Gibt es einen Hahn und Kolb Online Shop?

Combining robust rigidity with extended reach and proven insert compatibility, this boring bar delivers stable internal turning for medium-depth bores. With a 40 mm cutting diameter, 300 mm overall length and an S32T shank, the tool supports consistent chip control and precise bore geometry; order directly via Metav Werkzeuge or consult our specialists if further adaptation is required. Boring bar K197TM — 40 mm diameter, 300 mm overall length, Teknik Cutting Tools The Boring bar K197TM is a heavy-duty machining solution for internal turning using DC-- 11T3 indexable inserts, designed to maintain bore accuracy over extended reach in CNC production environments. S32T shank for high rigidity 40 mm cutting diameter for deep bores 300 mm overall length for extended reach Compatible with DC-- 11T3 indexable inserts Stable cutting performance for precise bores The Boring bar for DC-- 11T3 indexable inserts is engineered for dimensional stability during internal turning. Its S32T shank and 32 mm shaft provide a stiff connection to toolholders, reducing chatter and vibration—critical for maintaining tight tolerances in finished bores. The combination of a 40 mm cutting diameter and 34 mm cutting height concentrates cutting forces into a predictable vector, which helps preserve roundness and surface finish. In practice, this translates to fewer rework cycles and more consistent first-pass yields on serial production runs. Clear compatibility and machining behaviour explained Designed specifically for DC-- 11T3 indexable inserts, the bar accepts established insert geometries that simplify tooling management and spare-part stocking. The right-hand cutting configuration and the modest 3° cutting angle promote controlled chip formation and directional chip flow away from the bore, reducing the risk of recutting. The use of indexable inserts means edges can be rotated or replaced quickly without regrinding the body, saving set-up time and lowering life-cycle costs. The designation K197TM identifies the exact variant for ordering and cross-referencing in tooling lists. Practical advantages in workshop and production settings With an overall length of 300 mm the tool offers extended reach for deeper internal operations while the 22 mm clamping width on the cutting head secures the insert assembly for repeatable set-ups. At approximately 1.864 kg, the assembly balances mass for stable cuts without imposing excessive stress on the turret or spindle. These characteristics support efficient cycle times and predictable tool-change intervals, contributing to improved throughput. The robust construction suits a range of applications from precision finishing to medium-engagement roughing where indexable insert strategies are favoured for their cost-effectiveness and rapid maintenance. For tailored advice on integrating the Teknik Cutting Tools boring bar into the production process, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our consultants can help specify the right holder and insert combination for the task. Technical data Article number: K197TM Label: 40mm Bohrstange DC-- 11T3 L300mm Facts Cutting diameter: 40 mm Overall length: 300 mm Shaft diameter: 32 mm Cutting height: 34 mm Clamping width (cutting head): 22 mm Weight: 1.864 kg Cutting angle: 3° Cutting direction: right Special features Compatible with DC-- 11T3 indexable inserts S32T shank designation Product type: Boring bar SKU: K197TM FAQ What materials is this boring bar suited for? The boring bar K197TM is intended for general internal turning; compatibility with specific materials depends on the chosen DC-- 11T3 insert grade rather than the bar itself. How does the S32T shank benefit machining? An S32T shank increases connection rigidity between the tool and holder, improving stability and reducing vibration for more accurate bores with repeatable surface finishes. Can the cutting direction be changed? This variant is configured for right-hand cutting; for left-hand operations, an alternative tool geometry would be required. What does the 3° cutting angle affect in practice? The 3° cutting angle helps to control chip flow and cutting forces, leading to improved chip evacuation and reduced cutting resistance during internal turning. Which inserts should be ordered for this bar? Use DC-- 11T3 indexable inserts matched to the intended material and feed parameters; the bar is mechanically compatible with that insert family. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

High rigidity combined with internal coolant and a 40 mm body delivers consistent bore quality and extended tool life; the A32T shank and 300 mm overall length ensure straightforward integration into standard tooling setups. Order the Boring Bar KA224TM directly via Metav Werkzeuge or ask our consultants if needed. Boring Bar KA224TM — for VBMT 1604 indexable inserts, 40 mm with internal coolant (A32T) A Boring Bar KA224TM engineered for precision turning with VBMT 1604 indexable inserts, providing coolant-fed operation and a robust shank for repeatable bore finishes. 40 mm diameter for stable cutting Internal coolant for efficient chip evacuation Compatible with VBMT 1604 indexable inserts A32T shank ISO designation, robust construction Stable cutting and repeatable bore quality The solid design with a 40 mm body and 32 mm shaft diameter provides the rigidity necessary for consistent internal turning operations. The A32T ISO designation identifies the shank form so that the holder fits common turret and boring bar adapters without modification. With a 300 mm overall length and a mass of 1.79 kg, the tool balances reach and vibration dampening to reduce chatter; the result is fewer reworks and more predictable process windows. These measurable attributes translate directly into higher first-pass yields and lower scrap rates in batch production. Controlled cooling for longer tool life and process reliability Equipped with internal coolant, the bar directs cutting fluid precisely to the cutting edge, improving heat evacuation and chip clearance in deep or interrupted bores. Combined with the right-hand cutting orientation and a 107.5° cutting angle, the cooling stream reduces thermal loads on both insert and workpiece, which supports more consistent cutting forces and extended insert life. For operations where cycle time and insert consumption are critical KPIs, this toolholder architecture yields clear efficiency advantages and predictable maintenance intervals. Secure clamping and straightforward insert handling Designed for VBMT 1604 indexable inserts, the clamp head accepts standard insert geometry while allowing quick replacement: the clamp width of 22 mm and a cutting height of 50 mm ensure proper seating and stable force transmission. The fastening uses a Torx T15 driver and an M4x10 screw specification for positive torque control and repeatable clamp preload. Indexable inserts offer multiple cutting edges per part, and this system simplifies tool changeover, reducing downtime and supporting lean workflow strategies on the shop floor. Integration into workshop tooling and logistical benefits With a 32 mm shank diameter and the A32T mounting standard, the bar integrates with a wide range of adaptors and turret systems, helping to consolidate tooling inventories. The bar’s dimensions (300 mm overall length) and balanced mass enable practical handling and storage, while compatibility with commonly used inserts simplifies procurement and reduces lead times. Supplied under the Teknik Makina label and referenced as KA224TM, the holder is suited to industrial environments seeking standardised, maintainable tooling solutions. For tailored advice on selecting Teknik Cutting Tools boring bars and for order coordination, contact Metav Werkzeuge in Emmerich — our team will assist with technical matching and availability. Technical data SKU: KA224TM Label: 40mm Bohrstange VBMT 1604 L300mm mit Innenkühlung Product type: Boring bar Manufacturer: Teknik Makina ISO designation: A32T ECLASS: 21180806 UID: KA224TM Core specifications Diameter: 40 mm Overall length: 300 mm Shank diameter: 32 mm Cutting height: 50 mm Clamp head width: 22 mm Weight: 1.79 kg Cutting direction: right Cutting angle: 107.5° Torx key: T15 Screw: M4x10 Features Internal coolant Compatible with VBMT 1604 indexable inserts A32T shank ISO designation Right-hand cutting orientation Secure clamp with Torx T15 and M4x10 screw FAQ What insert type fits this boring bar? The holder is designed for VBMT 1604 indexable inserts; this compatibility allows use of standard carbide inserts suited to internal turning applications. Does the bar support coolant-fed machining? Yes, the boring bar includes internal coolant; the coolant channel supplies fluid directly to the cutting edge for improved cooling and chip control. What are the mounting and shank details for workshop integration? The bar uses an A32T shank form with a 32 mm shaft diameter, enabling straightforward mounting in compatible adaptors and turret systems. How is the insert secured and which fastener is required? Insert clamping is performed with a screw specified as M4x10, tightened using a Torx T15 driver to ensure repeatable clamp preload. Is this tool suitable for heavy-duty boring or long overhangs? The 40 mm body and 32 mm shank provide enhanced rigidity for typical internal turning; the 300 mm overall length offers a balance between reach and stiffness for many shop-floor applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a rigid, productivity-focused design that combines a 32 mm shank and a 60° cutting angle for stable turning with TNMG 1604 indexable inserts; order directly via Metav Werkzeuge or consult the experts for matching inserts and clamping options. MTENR for TNMG 1604 Indexable Inserts (S32T MTENR) — Boring bar with 32 mm shank, 300 mm overall length The MTENR for TNMG 1604 Indexable Inserts is a right-hand boring bar designed for external turning operations on CNC lathes, optimised for stability and repeatable performance with TNMG 1604 inserts S32T shank, 32 mm diameter Compatible with TNMG 1604 inserts Right-hand, 60° cutting angle 300 mm overall length, robust construction High rigidity for consistent surface finish and dimensional accuracy The holder's 32 mm shank and substantial body geometry reduce chatter and deflection during machining, which directly improves cycle-to-cycle repeatability. Built with a focus on rigidity, this boring bar converts stiffness into measurable production benefits: fewer rework cycles and more parts meeting tolerance on first pass. The S32T MTENR designation indicates a standardised shank and clamping interface, facilitating integration into existing tool assemblies while preserving stability for mid-to-heavy turning tasks. Precise insert compatibility that simplifies tool setup Designed specifically for TNMG 1604 indexable inserts, the tool holder ensures correct seating and stable clamping of triangular inserts with ground seating faces. The defined 60° cutting angle provides a predictable chip flow and cutting geometry that is well suited to general-purpose turning and facing. For manufacturing teams that standardise on TNMG inserts, this holder reduces setup time and inventory complexity by matching a widely used insert family to a robust tool body. Engineered for productive CNC turning cycles With a 300 mm overall length and balanced mass, the boring bar maintains effective reach without excessive overhang, supporting aggressive feed rates where the machine and workpiece permit. The right-hand cutting direction aligns with common lathe configurations and ensures reliable chip evacuation in standard turning passes. The unit's weight and dimensions are optimised to deliver productive metal removal while keeping vibration under control, aiding in consistent tool life and predictable maintenance intervals. Practical benefits for shop-floor integration Compatibility with TNMG inserts and a standard ISO designation helps streamline spare-part management and tool change routines. The combination of a sizable shank and engineered cutting geometry reduces the frequency of partial scrap and improves overall equipment effectiveness. For operations seeking a balance between robustness and flexibility, this boring bar delivers a straightforward route to increased throughput while enabling established insert strategies to remain in place. Discuss insert grades and clamping options with Metav Werkzeuge to match the MTENR holder to specific materials and cycle demands; Metav's Emmerich centre provides supply reliability and technical guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: K458TM Manufacturer: Teknik Makina Product name: MTENR for TNMG 1604 Indexable Inserts ISO designation: S32T MTENR Facts Shank diameter: 32 mm Cutting height: 60 mm Overall length: 300 mm Tool weight: 1.842 kg Applicable insert: TNMG 1604 Cutting angle: 60° Cutting direction: right Diameter: 40 Special features Indexable insert holder Right-hand turning geometry Robust construction for reduced vibration Standardised ISO shank designation FAQ What insert type fits this holder? The holder is designed for TNMG 1604 indexable inserts; TNMG-form inserts seat correctly in the MTENR pocket for secure clamping and repeatable positioning. Is the cutting direction right-hand or left-hand? This tool features a right-hand cutting direction, suitable for standard right-hand turning operations on lathes. What does S32T MTENR mean for shop fitting? S32T indicates the shank format and diameter standard, while MTENR identifies the pocket and orientation; together they ensure the boring bar integrates with common tool posts and holders. Can the holder be used for heavy roughing? The 32 mm shank and robust body provide enhanced stiffness, making the holder appropriate for medium to heavy turning where the machine and insert grade are matched to the task. Which organisation supplies this product and who handles European distribution? Teknik Cutting Tools is the manufacturer and distribution support for Europe is coordinated by Metav Werkzeuge for supply and technical advice. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine rigid stability with reliable insert compatibility: the left‑hand MTWN boring bar accepts TNMG 1604 indexable inserts and features a 32 mm shank for vibration‑resistant internal turning. Order directly via Metav Werkzeuge or consult their specialists for application matching. MTWN Boring Bar for TNMG Indexable Inserts — 32 mm shank, left‑hand (Teknik Makina) MTWN Boring Bar designed for left‑hand internal turning with TNMG 1604 indexable inserts, suited to medium‑duty machining and constrained bores. Left‑hand cutting direction for internal turning Compatible with TNMG 1604 indexable inserts 32 mm shank for enhanced rigidity and stability 300 mm overall length for deeper reach Stable performance for internal turning applications The MTWN boring bar is engineered to deliver consistent stability during internal turning operations. With a 32 mm shank, the holder reduces tool deflection and helps to prevent chatter when machining interrupted cuts or long overhangs. The robust geometry translates into improved surface finish and longer tool life for the chosen indexable inserts. Specified mass and dimensions contribute to predictable dynamic behaviour: a balanced assembly minimises vibration, making the tool suitable for repeatable production tasks where process reliability matters. Clear insert compatibility and cutting geometry explained Compatibility with TNMG 1604 indexable inserts provides a broad selection of grades and chipbreaker geometries, allowing adaptation to materials from mild steels to stainless alloys. The tool features a 60 mm cutting height, which sets the insert projection and seating for secure clamping, while the cutting angle 107.5° influences chip flow and edge engagement—valuable when optimising feeds and speeds. This combination of insert format and geometry enables effective material removal rates while maintaining control over cutting forces for internal contours. Practical integration, handling and shopfloor advantages Designed with the ISO designation S32T MTQNL, the boring bar integrates into standard turret and tooling systems without modification. The 300 mm overall length provides reach for deeper bore work, and the listed mass of 1.821 kg signals a substantial construction that assists stability during machining. The clamp interface identified as Clamp size 16 supports secure screw tightening and repeatable clamping of the insert seat. Selection of this bar supports streamlined tooling setups: fewer changeovers, reliable insert seating and compatibility with common TNMG insert families reduce process interruptions and inspection effort. Choose the Teknik Makina MTWN boring bar for left‑hand internal turning and contact Metav Werkzeuge in Emmerich for tailored application advice and order support via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: K538TM Manufacturer: Teknik Makina Designation: MTWN for TNMG Indexable Inserts (Boring bar) Facts Shank diameter: 32 mm Overall length: 300 mm Cutting height: 60 mm Weight: 1.821 kg Diameter: 40 mm Cutting angle: 107.5° Special features Compatible with TNMG 1604 indexable inserts Left‑hand cutting direction ISO designation S32T MTQNL Clamp size: 16 Brand: Teknik Makina FAQ What insert type does the boring bar accept? The MTWN boring bar accepts TNMG 1604 indexable inserts, offering a wide range of grades and chipbreakers for different materials and cutting conditions. Is this tool suitable for left‑hand internal turning only? Yes, the bar is configured for a left‑hand cutting direction and is optimised for internal turning tasks that require that orientation. What are the key dimensions to consider for toolholders? Relevant dimensions are the 32 mm shank diameter, 300 mm overall length, and 60 mm cutting height, which determine rigidity, reach and insert seating. How does the ISO designation affect compatibility? The S32T MTQNL designation ensures the boring bar fits standard turret and holder systems, simplifying integration with existing tooling setups. Can the MTWN bar be used for deep bores? With a 300 mm overall length and a robust shank, the bar is suitable for deeper bores where reach and stability are required; final suitability depends on machine setup and cutting parameters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid 32 mm shank, coolant-fed design and direct compatibility with CNMG 1204 inserts for stable, repeatable turning and facing operations; the tool’s 300 mm overall length gives extended reach while maintaining stiffness. Order the boring bar directly via Metav Werkzeuge or ask our consultants if needed. Boring bar A32T PCLNL — coolant-fed PCLN holder for CNMG 1204 indexable inserts (Teknik Makina) Boring bar A32T PCLNL is a coolant-supported turning bar intended for left-hand cutting operations with CNMG 1204 indexable inserts, suited to workshop and production use where rigid clamping and controlled chip evacuation are required. Boring bar A32T PCLNL by Teknik Makina Internal coolant for consistent chip evacuation Compatible with CNMG 1204 indexable inserts Stable machining and predictable chip control The A32T PCLNL holder combines a 32 mm shank with a robust holder body to reduce vibration and improve surface finish on the workpiece. The geometry accommodates CNMG 1204 indexable inserts and a 95° cutting angle, which together deliver a secure cutting action and reliable tool engagement. For applications where dimensional consistency and repeatability are essential, the construction of this holder increases process stability and lowers scrap rates by limiting deflection during heavy cuts. Coolant feed and extended insert life Built-in internal coolant directs lubricant and coolant close to the cutting edge, supporting efficient heat removal and chip breaking. The internal feed reduces thermal load on the insert and cutting edge, which contributes to longer tool life and more consistent cycle times. With an overall length of 300 mm, the holder balances reach with stiffness; this configuration is beneficial for medium-reach boring and external turning where coolant-assisted chip control is required to maintain machining quality. Practical applications and integration into workflows Designed for left-hand cutting and specified as A32T PCLNL in ISO terms, the holder suits general turning, facing and light boring tasks when fitted with the specified inserts. The tool is supplied for use with CNMG 1204 plates and is therefore compatible with a broad range of carbide grades and coatings offered by insert manufacturers. Its 40 mm diameter body and a cutting height of 50 mm allow secure clamping and straightforward integration into existing tool posts and turret systems, supporting efficient changeover and consistent set-ups across production batches. For specification advice or to arrange supply of the Teknik Cutting Tools A32T PCLNL coolant-fed boring bar, contact Metav Werkzeuge for tailored recommendations and prompt delivery arrangements. Technical data Article number: AP352TM Manufacturer: Teknik Makina ISO designation: A32T PCLNL Designation: PCLN for CNMG Indexable Inserts Dimensions & weight Shank diameter: 32 mm Overall length: 300 mm Cutting height: 50 mm Diameter: 40 mm Weight: 1.809 kg Cutting angle: 95° Features & applications Internal coolant: yes Suitable for CNMG 1204 inserts Left-hand cutting direction Coolant-fed holder design FAQ What inserts fit this holder? The holder is specified for use with CNMG 1204 indexable inserts; the PCLN style accepts the standard CNMG plate geometry for turning and facing. Does the tool provide internal coolant? Yes, the A32T PCLNL boring bar features internal coolant to improve chip evacuation and reduce cutting temperatures during operation. What are the key dimensions for set-up? Key measurable data are listed above: shank diameter 32 mm, overall length 300 mm, diameter 40 mm and cutting height 50 mm, which support accurate fixture and clamping planning. Is the cutting direction important for this tool? The tool is designed for left-hand cutting; confirm the machine turret orientation and program directions to ensure correct installation and machining direction. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise, repeatable finishing and robust clamping to reduce rework and secure consistent bore quality; the combination of a 25 mm shank, Ø40 mm max cutting diameter and compatibility with CCMT 0602 inserts supports efficient production. Order or discuss delivery options via Metav Werkzeuge for prompt supply and expert advice. Fine boring tool for fine finishing – Teknik Makina Fine boring tool for fine finishing designed for internal finishing applications and compatible with standard CCMT 0602 indexable inserts Fine finishing to 0.01 mm tolerance Compatible with CCMT 0602 inserts 25 mm shank for stable clamping Ø40 mm max cutting diameter Consistent fine finishes with measurable precision The boring bar is engineered to deliver high-precision internal finishes, enabling achievable tolerances down to 0.01 mm for demanding components. Its geometry and recommended insert grade are optimised for minimal vibration and uniform material removal, which reduces the need for secondary operations. By pairing the holder with CCMT 0602 indexable inserts, machinists obtain a reliable combination for repeatable bore quality in series production and prototype runs alike. Stable set-up for higher metal-removal efficiency A 25 mm shank and a substantial effective length provide the rigidity required for stable clamping and improved tool life. The tool’s dimensions—60 mm cutting length on the shank and an overall length of 116 mm—support secure seating in standard toolholders while allowing access into deeper bores. This stability permits slightly higher cutting parameters where the workpiece and machine permit, helping to increase throughput without compromising surface integrity. Flexible integration and practical workshop benefits Compatibility with commonly available indexable inserts simplifies stocking and tool change routines; the use of CCMT 0602 inserts ensures an economical, proven cutting edge for finishing operations. With a maximum cutting diameter of 40 mm and a tool weight around 0.51 kg, the holder balances manoeuvrability and mass for controlled cutting dynamics. For shops aiming to streamline tooling logistics, the tool integrates well with existing setups and supports predictable cycle times and quality outcomes. Contact Metav Werkzeuge today to review specifications, check availability or request a tailored delivery from our Emmerich stock Technical data SKU: THKB126TM Manufacturer: Teknik Makina Facts Max cutting diameter: 40 mm Shank diameter: 25 mm Cutting shank length: 60 mm Overall length: 116 mm Fine finishing capability: 0.01 mm Weight: 0.51 kg Special features Compatible inserts: CCMT 0602 Designed for internal fine finishing Balanced design for reduced vibration FAQ What tolerance can be achieved with this boring bar? The boring bar supports fine finishing down to 0.01 mm, enabling consistent internal surface quality suitable for precision components. Which insert type is required for the holder? The holder accepts CCMT 0602 indexable inserts; this common size facilitates economical tool changes and simple procurement. Is the tool suitable for deeper bores? With an overall length of 116 mm and a 60 mm effective cutting shank, the tool is intended for moderate-depth internal finishing where rigidity can be maintained. What is the article SKU and the supplying brand? The article is listed as THKB126TM and is supplied by Teknik Makina; the design focuses on fine internal finishing and compatibility with standard workshop inserts. Manufacturer: Teknik Cutting Tools; Buyukkayacık OSB Mah.422 Nolu Sokak No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of 0.01 mm finishing accuracy combined with a 25 mm shank for stable machining and reduced rework; the tool's compatibility with CCMT 0602 inserts ensures rapid indexable insert changes and consistent surface quality. Order the boring tool directly via Metav Werkzeuge or consult the team for application-specific advice. Boring tool for fine finishing — Teknik Makina fine-finishing boring bar with CCMT 0602 compatibility Boring tool for fine finishing designed for precision internal finishing in production workshops and toolrooms High-precision finishing to 0.01 mm Accepts CCMT 0602 indexable inserts 25 mm shank for stable clamping 125 mm overall length for deep bore access Consistent fine finishing for demanding internal bores The boring bar delivers a proven capability for tight-surface tolerances, with a documented fine finishing capability of 0.01 mm. This level of control reduces the need for subsequent polishing or rework and supports parts that must meet tight geometrical and surface specifications. Built to accept CCMT 0602 indexable inserts, the holder enables predictable chip formation and an easily repeatable finish quality. For production lines where cycle consistency and first-pass yield matter, the combination of fine tolerance and indexable inserts translates directly into fewer rejects and lower downstream labour costs. Rigid design that minimises chatter and improves productivity A 25 mm shank and compact overall length of 125 mm provide a stiff tool-holding solution that resists deflection in finishing passes. The tool's cutting portion extends 69 mm, allowing access into deeper bores while maintaining the necessary rigidity for high-quality finishes. Reduced vibration and improved tool stability lead to longer insert life and steadier cutting parameters, which in turn lowers setup time and increases machine throughput. These mechanical advantages support efficient machining on both CNC lathes and conventional turning centres. Fast insert replacement and straightforward integration into toolcycles Compatibility with standard CCMT 0602 inserts makes insert procurement and replacement simple and economical. Indexable inserts allow quick corner changes without the need for regrinding, reducing machine downtime and simplifying tooling logistics. The design supports common clamping systems and can be integrated into existing tool racks and presetting routines, so shops benefit immediately from lower setup complexity and faster return on tooling investment. Applications, target users and workshop benefits Intended for precision internal finishing tasks up to a 50 mm cutting diameter, this boring bar suits toolrooms, precision engineering shops and serial production environments that value surface integrity and dimensional accuracy. The rigour of the mechanical design and insert system brings practical benefits: fewer quality inspections, predictable maintenance intervals and consistent part quality. For workshops seeking dependable finishing solutions, the tool offers a clear productivity uplift and helps maintain standards across batches. Contact Metav Werkzeuge to arrange supply or a technical consultation on the Teknik Makina fine finishing boring tool THKB132TM — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical data Article number: THKB132TM Manufacturer: Teknik Makina Numerical data Maximum cutting diameter: 50 mm Shank diameter: 25 mm Cutting length: 69 mm Overall length: 125 mm Weight: 0.722 kg Fine finishing capability: 0.01 mm Designs / Special features Compatible inserts: CCMT 0602 Designed for fine finishing internal bores Indexable insert holder for rapid replacement FAQ What diameter range is suitable for machining with this boring bar? This boring bar is designed for internal finishing operations up to a 50 mm cutting diameter and is optimised for fine finishing work with the Teknik Makina boring tool THKB132TM. Which insert type is required for this holder? The holder is compatible with CCMT 0602 indexable inserts; using these standard inserts with the Teknik Makina fine finishing boring tool THKB132TM enables quick changes and consistent results. How does the shank diameter affect performance? The 25 mm shank diameter increases rigidity and reduces deflection during finishing passes, improving surface quality and insert life when using the Teknik Makina boring bar THKB132TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine stable 40 x 40 mm clamping geometry, a 40 mm cutting height and a secure M5x18 Torx fastening for consistent right‑hand external threading; order the clamp holder via Metav Werkzeuge or request consultant support for fitting and compatibility. Clamp holder SER 4040 – right‑hand external threading, 40 x 40 mm – Teknik Makina A heavy‑duty clamp holder engineered for right‑hand external thread turning and compatible with 27 ER indexable inserts in professional machine shops. Robust 40 x 40 mm clamping body 40 mm cutting height for deep threads Secure M5x18 Torx fastening Compatible with 27 ER indexable inserts Stable geometry for repeatable thread quality The primary advantage of this toolholder is its precise clamping geometry. The 40 x 40 mm cross section and 40 mm cutting height provide a rigid interface that reduces vibration during threading cycles, which in turn improves surface finish and dimensional repeatability. Mass distribution and the unit’s 2.589 kg weight contribute to stability on the carriage, so thread forms are produced consistently even under interrupted cuts. The ISO designation SER 4040 identifies the shank profile for straightforward integration into standard toolposts. Quick assembly and secure fixing to reduce downtime Designed for efficient workflows, the holder accepts 27 ER indexable inserts and mounts on the R27‑ER27 boring bar designation, enabling rapid insert changes without extensive reset procedures. Fixing is by an M5x18 Torx screw tightened with a T20 key, a combination that gives positive clamping force while remaining serviceable on the shop floor. The included U plate reference TA064 ensures compatibility with common mounting plates. Together, these features reduce set‑up time and make the toolholder suitable for batch production or mixed‑series turning tasks. Practical applications and operational benefits Optimised for right‑hand external threading, this holder is intended for industrial turning centres and manual lathes where reliable thread cutting is required. The robust construction supports operations in toolrooms and production lines that demand repetitive accuracy rather than one‑off setups. The overall length of 200 mm gives an accessible reach without compromising rigidity, and the toolholder is specified for right‑hand cutting direction. For purchasers, the clear technical alignment with 27 ER inserts simplifies stocking decisions and streamlines tool change procedures. Durability, compatibility and supply confidence Manufactured by Teknik Cutting Tools and distributed through Metav’s European channel, the holder benefits from tested manufacturing processes and logistical support from Emmerich. The combination of standardised ISO shank, proven fastening elements and common insert compatibility minimises the risk of mismatched components. For operations aiming to improve first‑pass yield on threaded parts, the assembly represents a pragmatic, high‑performance choice that balances ease of use with industrial robustness. For professional right‑hand external threading, contact Metav Werkzeuge for technical advice or to arrange supply of the Teknik Cutting Tools clamp holder (SKU D493TM) from our Emmerich stock Technical Data Article number: D493TM Manufacturer: Teknik Makina SKU: D493TM ECLASS: 21181004 ISO designation: SER 4040 Facts Width: 40 mm Height: 40 mm Cutting height: 40 mm Overall length: 200 mm Weight: 2.589 kg Special features Compatibility: 27 ER indexable inserts Boring bar designation: R27‑ER27 U plate reference: TA064 Torx screw: M5x18 Torx key: T20 Right‑hand cutting direction FAQ Is this holder suitable for external right‑hand thread cutting? Yes. The clamp holder (SER 4040) is specified for right‑hand external threading and is configured to accept 27 ER indexable inserts for thread‑forming and finishing operations. Which insert system fits this toolholder? The holder is compatible with 27 ER indexable inserts and is designed to mate with the R27‑ER27 boring bar interface. What fastening method secures the insert / tool to the holder? Fixing is achieved via an M5x18 Torx screw tightened with a T20 key, providing reliable clamping for machining forces encountered during threading. How does the holder improve thread quality on the lathe? The 40 x 40 mm clamping geometry and 40 mm cutting height increase rigidity and reduce vibration, leading to improved dimensional repeatability and surface finish on threaded components. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, rigid design with internal coolant and compatibility with ADKT 10T3 indexable inserts for stable turning performance; order directly via Metav Werkzeuge or consult our specialists for application advice. Corner tool head for ADKT 10T3 indexable inserts — 40 mm, internal coolant (Teknik Makina) A durable corner tool head designed for turning operations with ADKT 10T3 indexable inserts, offering integrated coolant supply and a compact 40 mm form factor for stable engagement in CNC lathes and turning centres. 40 mm head diameter Integrated internal coolant supply Compatible with ADKT 10T3 inserts Five cutting positions Greater process stability through rigid design and coolant The compact 40 mm head delivers increased stiffness at the cutting zone, which reduces vibration and improves surface consistency during finishing passes. The 40 mm dimension and lightweight construction contribute to controlled tool overhang, while the internal coolant channel directs coolant to the cutting edge, aiding chip evacuation and extending insert life. These engineering choices are intended to support predictable cycle times in serial production and precision reworking. Minimised downtime with proven indexable insert compatibility Compatibility with ADKT 10T3 insert geometry—commonly supplied by Korloy—means quick insert indexing and minimal set-up changeover. The holder accepts inserts with indexed positions, providing five cutting positions that can be rotated as edges wear, reducing consumable costs per component. Fast removal and secure clamping are achieved via the specified torx fastenings, ensuring repeatable seating and reliable tool life. Servicing and handling that keep workshops productive Maintenance routines are simplified by the standardised fastener arrangement: a Torx T8 key interfaces with the head and the retaining screw specified as M2.5x5.5 ensures consistent clamp torque. The modest mass of 0.18 kg improves dynamic behaviour in high-speed routines and reduces spindle load during rapid acceleration. Careful selection of fastener torque and periodic inspection of coolant passages will preserve performance and help avoid unplanned stops. Where this tool head adds the most value Engineered for precision turning tasks in small-batch production and industrial workshops, this corner tool head supports operators aiming to improve surface quality and reduce insert consumption. The combination of indexable inserts, directed coolant, and compact geometry makes it a practical choice where repeatability, short changeovers and reliable clamping are priorities for throughput and quality control. For specification confirmation, procurement or technical guidance on the Teknik Makina corner tool head (SKU T696TM), contact Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice and rapid supply. Technical data SKU: T696TM Product type: Corner tool head Label: 40mm Eckmesserkopf ADKT 10T3 L40mm mit Innenkühlung Manufacturer: Teknik Makina Core specifications Diameter: 40 mm Overall length: 40 mm Weight: 0.18 kg Cutting positions: 5 Torx key: T8 Torx screw: M2.5x5.5 Internal coolant: yes Special features Compatible with ADKT 10T3 indexable inserts Compatible insert manufacturer: Korloy eClass: 21181015 SKU: T696TM FAQ Which insert type fits this head? The corner tool head accepts ADKT 10T3 indexable inserts; compatibility is specified for ADKT 10T3 geometries. Does the tool head provide internal coolant? Yes, the holder is supplied with internal coolant to direct cutting fluid to the insert edge for improved cooling and chip control. How many indexed positions are available per insert? The design provides five cutting positions, allowing rotation to fresh edges as wear occurs. What fastening tools and screws are required? Insert retention uses a Torx T8 interface and the retaining screw specified is M2.5x5.5. Is this head suitable for production CNC lathes? The holder is intended for precision turning operations on CNC lathes and turning centres where quick indexable insert changes and coolant delivery are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise 40 mm cutting diameter, internal coolant, and compact overall length for consistent cycle times and improved chip control; order or request assistance via Metav Werkzeuge to integrate this corner tool head into existing turning setups. Corner tool head T365TM – 40 mm diameter with internal coolant (for XEKT 1904 Indexable Inserts) by Teknik Makina A corner tool head engineered for precision shoulder and corner turning with XEKT 1904 indexable inserts, offering integrated coolant supply for reliable chip control in CNC turning operations. Precision 40 mm cutting diameter Internal coolant for optimal chip evacuation Compatible with XEKT 1904 indexable inserts Three cutting edges for balanced machining Consistent cutting performance through compact geometry The 40 mm diameter cutting geometry combined with a 45 mm overall length produces a compact solution that reduces overhang and helps maintain stable cutting conditions. The head's three cutting edges are arranged to distribute cutting forces evenly, which supports constant cycle times and a predictable surface finish. With a mass of 0.192 kg, inertia is lowered, reducing susceptibility to chatter on medium to short tool projections; this leads to higher process reliability and fewer rework cycles. Secure mounting and straightforward serviceability Designed for standardised fastening, the head uses T15 Torx drive for the clamping screws and accepts M4x8.5 Torx screws, enabling secure torque transmission and simple maintenance routines. The tool accepts XEKT 1904 indexable inserts and is compatible with inserts from Korloy, allowing quick insert changes and inventory harmonisation in mixed-brand workplaces. A 16 mm mounting interface ensures compatibility with typical toolholder systems used in industrial turning centres. Improved cooling, chip control and surface quality Built-in internal coolant directs cutting fluid close to the cutting edge, improving thermal management and assisting chip breakage. This targeted cooling reduces heat-related wear on the insert and promotes consistent dimensional results over longer tool life. The 90° cutting angle design is particularly effective for square-shoulder operations and gives reliable reference surfaces without complex tool reorientation, simplifying setup times for batch production. Practical advantages for workshop and production environments The head is suited to workshops seeking a compact, versatile cutting solution for external turning and shoulder profiling where fast insert changes and coolant-fed machining are desirable. The compatibility with widely used XEKT 1904 inserts and Korloy supply chains helps reduce procurement complexity. With standard fasteners and a design focused on stable engagement, the head supports efficient tool changeovers, lower downtime and a more predictable process flow in small to mid-sized turning operations. Contact Metav Werkzeuge for advice on integrating the Teknik Makina T365TM corner tool head with internal coolant into production setups and to request application guidance from our Emmerich-based specialists. Technical data SKU: T365TM Product: Corner tool head Brand: Teknik Makina Facts Diameter: 40 mm Overall length: 45 mm Weight: 0.192 kg Mounting bore: 16 mm Cutting edges: 3 Cutting angle: 90° Torx key size: T15 Torx screw: M4x8.5 Internal coolant: yes Special features Compatible inserts: XEKT 1904 Compatible insert supplier: Korloy ECLASS: 21181015 Label: 40mm Eckmesserkopf XEKT 1904 L45mm mit Innenkühlung FAQ What insert type fits this head? The head is specified for XEKT 1904 indexable inserts; it is also compatible with inserts from Korloy when used with the Teknik Makina T365TM corner tool head. Is the coolant fed through the tool body? Yes, internal coolant is integrated in the T365TM, enabling coolant delivery directly to the cutting zone for improved chip evacuation and thermal control. Which fastening hardware is required for mounting? Mounting and clamp screws for the T365TM use a T15 Torx drive and M4x8.5 Torx screws as specified for secure assembly. What operations is this head best suited to? The corner tool head is optimised for 90° shoulder turning and profiling tasks on CNC lathes, where compact geometry and coolant-fed cutting improve consistency. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid turning solution that combines precise 90° cutting geometry with broad compatibility; the robust Torx clamping and 16 mm shank ensure repeatable seating and vibration-resistant performance. Order the component directly via Metav Werkzeuge or consult the technical team for application advice. Corner tool head T853TM — Corner turning head for XNKT 0604 indexable inserts (Teknik Makina) The Corner tool head T853TM delivers a secure, 90° turning option for lathe and CNC finishing operations, designed specifically for XNKT 0604 indexable inserts and compatible with Korloy inserts. Secure Torx M3x7 clamping Fits XNKT 0604 inserts (Korloy) 16 mm shank for rigid mounting 90° cutting angle for square shoulders Precision and stability for consistent turning results The head is engineered to provide repeatable geometry in shoulder turning and profiling. With a defined 90° cutting angle and a 16 mm shank for firm spindle seating, the component reduces deflection during interrupted cuts and maintains tool path accuracy. The combination of a compact diameter 40 mm head and total length 40 mm offers a short overhang that contributes to lower vibration and improved surface finish. These measurable attributes translate into fewer reworks and predictable cycle times on production runs. Quick, reliable clamping for faster set-up The component uses a Torx M3x7 clamping screw secured with a T8 key, enabling fast and secure insert retention. The Torx interface concentrates torque at the screw head for consistent clamp force and reduced screw cam-out, which supports frequent index changes without loss of seating precision. Compatibility with Korloy XNKT 0604 indexable inserts shortens procurement and inventory complexity for workshops that standardise on that insert family, simplifying changeovers and spare-part management. Designed for workshop efficiency and compatibility Weighing just 0.219 kg, the head balances low mass with mechanical rigidity, allowing agile handling during tool changes while contributing minimal centrifugal load at higher spindle speeds. The six cutting-edge orientation supports common indexable insert geometries, making the holder suitable for finishing and semi-finishing passes where controlled chip flow and tool life are priorities. The compact form factor and standardised mounting facilitate integration into existing tool turrets and multi-station toolposts. Practical benefits explained for procurement and operators Selecting this head reduces inventory variety through standard compatibility and delivers a tangible improvement in process reliability via robust clamping and short overhang. The standardised 16 mm mounting diameter is a common fit in workshop tooling systems, easing retrofits. For operators less familiar with insert tooling: an indexable insert is a replaceable cutting tip; the head secures that tip and defines its cutting angle, so maintaining correct clamp torque and using the specified T8 key ensures optimal seating and predictable wear patterns. Contact Metav Werkzeuge for tailored application advice and secure the Teknik Cutting Tools Corner tool head T853TM with 16 mm shank and Torx M3x7 clamping—phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data SKU: T853TM EClass: 21180902 Manufacturer: Teknik Cutting Tools Numbers Diameter: 40 mm Total length: 40 mm Shank diameter: 16 mm Weight: 0.219 kg Cutting angle: 90° Cutting edges: 6 Features For XNKT 0604 indexable inserts Compatible with Korloy inserts Torx screw M3x7 clamping Torx key size T8 FAQ What size of insert does this head accept? The head accepts XNKT 0604 indexable inserts and is compatible with Korloy inserts in that format. Which shank diameter is required for mounting? Mounting requires a toolholder or turret accepting a 16 mm shank. What type of clamping screw is used and which key is required? Clamping uses a Torx M3x7 screw and is tightened with a T8 key for consistent clamp force. Is the head suitable for shoulder turning at 90°? Yes, the head is specified with a 90° cutting angle, designed for square shoulder and corner turning tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid design that combines a 40 mm tool diameter with internal coolant and compatibility with Taegutec 3PKT 1505 indexable inserts for reliable corner turning and reduced tool-change downtime; order directly via Metav Werkzeuge or consult the technical team for integration advice. Eckmesserkopf — Corner tool head, 40 mm with internal coolant (Teknik Makina) A compact Eckmesserkopf corner tool head for 3PKT 1505 indexable inserts, engineered for stable, repeatable turning where consistent edge performance and controlled cooling are required. 40 mm diameter tool head Internal coolant supply Compatible with Taegutec 3PKT 1505 inserts Four cutting edges, 90° cutting angle Stable cutting with integrated coolant for longer tool life The built-in internal coolant channel directs cutting fluid directly to the cutting zone to improve chip evacuation and thermal control. This reduces flank wear and helps maintain a consistent cutting edge under production loads, delivering measurable increases in service intervals and process stability. For workshops aiming to reduce unplanned stoppages, the coolant feed lessens heat-related tool degradation and supports tighter tolerances when machining with indexable inserts. Rigidity and geometry for accurate corner turning With a 40 mm diameter and a compact overall length of 40 mm, the tool head provides the stiffness required for precise corner operations. The geometry offers a 90° cutting angle and four cutting edges, which combine to reduce vibration and deliver a predictable cutting force direction. The result is improved surface finish and repeatability across batches, particularly beneficial in small-series production or high-mix environments where setup consistency is essential. Convenient insert clamping and fast maintenance Insert changes are secured with a Torx fastener (Torx T15) and a M4x10 screw, enabling quick, repeatable clamping without specialised tools. The configuration supports standard 3PKT 1505 indexable inserts from Taegutec, simplifying spare-part logistics. With a compact mass of 0.268 kg, the tool head minimises additional load on the toolholder while maintaining the mechanical stability required for fine turning and finishing passes. Broad workshop compatibility for efficient production Designed as a practical component for turning tool assemblies, the head fits seamlessly into standard setups and supports common indexable insert formats. The compatibility with Taegutec inserts and the clear mechanical specifications make it straightforward to integrate into existing tooling arrays, reducing inventory complexity and enabling faster job changeovers. This component is aimed at production shops and precision engineering workshops seeking to harmonise performance, availability and process reliability. Contact Metav Werkzeuge for ordering and integration guidance on the Teknik Makina Eckmesserkopf T397-1TM; technical consultants in Emmerich can advise on fitment and process optimisation — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T397-1TM Product type: Corner tool head (Eckmesserkopf) Manufacturer: Teknik Makina Compatible inserts: 3PKT 1505 Compatible insert manufacturer: Taegutec Internal coolant: yes Fastening: Torx T15 / M4x10 Facts Diameter: 40 mm Overall length: 40 mm Aufnahme diameter: 16 mm Cutting edges: 4 Cutting angle: 90° Weight: 0.268 kg eClass: 21181015 Special features Internal coolant channel Compatible with 3PKT 1505 indexable inserts Torx key size T15 Fastening screw M4x10 SKU: T397-1TM FAQ Is this head compatible with Taegutec 3PKT 1505 indexable inserts? Yes. The Eckmesserkopf T397-1TM is specified for 3PKT 1505 indexable inserts and is compatible with inserts from Taegutec, ensuring standardised fitment and reliable seating. What benefit does the internal coolant provide? The internal coolant in this corner tool head directs fluid to the cutting zone to improve chip control and heat dissipation, prolonging insert life and stabilising machining results under continuous production. How many cutting edges and what cutting angle does the tool head have? The tool head features four cutting edges and a 90° cutting angle, designed to provide stable corner performance and improved surface finish in turning applications. What fastening hardware is required for insert clamping? Insert clamping uses a Torx drive; the tool head requires a Torx T15 key and M4x10 screw for secure and repeatable insert retention. Which applications suit this corner tool head best? The component is suited to precision corner turning, finishing passes and general turning tasks where indexable inserts are preferred; it is designed for workshops and production environments that require quick insert changes and consistent machining results. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid tool head that delivers precise 90° shoulder cuts and fast, secure insert changes; the combination of 16 mm shank stability and lightweight design supports repeatable results and reduced downtime. Order the component via Metav Werkzeuge or request clarification from our consultants. Eckmesserkopf T440TM — 90° indexable insert tool head by Teknik Makina, 16 mm shank The Eckmesserkopf T440TM is a 90° turning head designed for reliable shoulder and facing operations with standard indexable inserts and a compact 16 mm toolholder interface. 90° cutting angle for accurate shoulder cuts 16 mm shank diameter for compact toolholders Compatible with ISCAR indexable inserts Supplied with M5x12 Torx fixing screw Consistent accuracy and rigidity for shoulder machining The 90° geometry delivers a defined cutting orientation that is especially useful for shoulder turning and facing tasks where perpendicularity matters. By combining a 90° cutting angle with a 16 mm shank, the head offers improved stiffness compared with slimmer adaptors, which reduces chatter and improves surface finish. The 40 mm diameter and 45 mm overall length contribute to a stable cutting envelope while the modest mass of 0.279 kg keeps the assembly light enough for quick tool changes. These characteristics translate into fewer rejected parts and shorter cycle times on repetitive production runs. Quick, secure clamping and straightforward maintenance Fast insert retention is enabled by the supplied M5x12 Torx screw together with the T20 key specification, ensuring a positive clamp with predictable torque characteristics. The clear specification of the fixing hardware simplifies procurement and maintenance planning, and the head’s compatibility with ISCAR indexable inserts streamlines inventory since widely used insert families can be mounted without adapters. Reduced changeover time and a familiar clamping system enhance overall equipment effectiveness on the shop floor. Built for everyday workshop versatility The compact design suits a wide range of turning centres and tool posts where space is limited but performance is required. The head is intended for operations that demand clean shoulder faces and defined step features; its form factor enables use in tight set-ups and on smaller lathes. Because the component integrates common mechanical interfaces, it becomes an efficient option for job shops and production lines that favour interoperable tooling systems and minimal bespoke tooling. Productivity gains and cost-conscious tooling strategy By providing a repeatable 90° orientation and robust clamping in a lightweight package, the head helps to reduce rework and extend insert life through stable cutting conditions. Matching the head with standard ISCAR inserts allows purchasing teams to concentrate on fewer insert types, lowering complexity and storage costs. Combined with Metav’s reliable supply chain and technical advice from Emmerich, the T440TM supports a practical, productivity-focused tooling strategy that benefits both small workshops and industrial production environments. Discuss the Teknik Makina T440TM with Metav Werkzeuge in Emmerich—call +49 2822 7131930 or email info@metav-werkzeuge.com to confirm compatibility with existing toolholders and secure timely delivery Technical data Article number: T440TM Manufacturer: Teknik Makina SKU: T440TM Torx screw: M5x12 Torx key size: T20 Compatible insert manufacturer: ISCAR Facts Shank diameter: 16 mm Overall length: 45 mm Diameter: 40 mm Weight: 0.279 kg Cutting angle: 90° Number of cutting edges: 3 Special features Compatibility with ISCAR indexable inserts 90° geometry for shoulder and facing operations Supplied fixing screw M5x12 and Torx drive T20 FAQ Which insert systems fit this tool head? The head is compatible with ISCAR indexable insert systems; confirm specific insert family and seat type before ordering to ensure perfect fit. What is the shank diameter and how does it affect rigidity? The shank diameter is 16 mm; this provides higher stiffness than smaller adaptors and helps to reduce vibration during shoulder machining. What fixing screw and key size are included? Fixing hardware is specified as an M5x12 Torx screw; the corresponding Torx key size is T20. Is the head suitable for precision shoulder turning? Yes — the 90° cutting orientation is designed for shoulder and facing operations where perpendicularity and defined steps are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact 90° indexable insert tool head that combines secure Torx M4x10 clamping, a standard 16 mm shank and compatibility with Walter LNGX 1307 inserts; this ensures stable turning operations and straightforward insert changes. Order the component directly via Metav Werkzeuge or contact the consultants for integration advice. Teknik Makina 90° Indexable Insert Tool Head (T488TM) — for Walter LNGX 1307 inserts, 16 mm shank A 90° indexable insert tool head (T488TM) designed for turning and profiling where precise corner machining and compatibility with Walter LNGX 1307 indexable inserts are required 90° cutting angle for precise corner turning Compatible with Walter LNGX 1307 inserts 16 mm shank for standard tool holders Torx M4x10 clamping with T15 key required Secure clamping and compact footprint for consistent results The holder features a 16 mm shank and a compact 45 mm overall length, delivering a stable connection to the tool post while keeping the working envelope small. Clamping is effected with an M4x10 Torx screw, tightened with a T15 key, which provides repeatable seat contact and reduces micro‑movement during cut engagement. At a mass of 0.304 kg, the assembly maintains low inertia, which can contribute to reduced chatter on light to medium‑duty lathes. The mechanical design focuses on rigidity and simple serviceability to support consistent machining cycles. Direct compatibility with Walter LNGX 1307 indexable inserts Designed specifically for Walter LNGX 1307 inserts, the head accepts the prescribed insert geometry and secures it for accurate edge location. This compatibility removes the need for adapter plates and simplifies inventory management when Walter inserts are already in use. The indexed insert format enables fast edge rotation or replacement, minimising downtime and preserving cycle‑time efficiency. For operations requiring a standardised insert form, the holder ensures correct seating and tool alignment within industry tolerances. 90° geometry for precise shoulder and face turning A true 90° cutting angle is particularly advantageous for producing square shoulders, external chamfers and precise face profiles without secondary referencing. The tool head’s 40 mm diameter and triple‑edge configuration support balanced cutting forces and an even load distribution across the insert seat. In practice, this geometry reduces the need for multiple passes on perpendicular features and can improve first‑pass dimensional conformity, especially where tight angular accuracy is required. Practical applications and maintenance guidance The component is suited to external turning, shoulder finishing and short‑reach profiling in general mechanical workshops and light industrial turning centres. Routine inspection focuses on the clamping screw torque and insert seating; the Torx interface and standard screw size simplify replacements and spare part logistics. For integration into existing workflows, Metav Werkzeuge can supply the tool head as a single item or advise on compatible tool holders and insert stocks to streamline procurement and reduce setup time. For personalised supply and technical advice on integrating the T488TM 90° indexable insert tool head into production, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for prompt assistance. Technical data SKU: T488TM Manufacturer: Teknik Makina Shank diameter: 16 mm Tool diameter: 40 mm Overall length: 45 mm Weight: 0.304 kg Cutting angle: 90° Compatible with Walter LNGX 1307 inserts Torx screw M4x10 Torx key T15 Three cutting edges Suitable for turning and shoulder finishing FAQ What inserts fit this tool head? The tool head accepts Walter LNGX 1307 indexable inserts; the seat geometry is matched to that insert type for accurate location and secure clamping. Which shank size is required for mounting? Mounting requires a 16 mm shank interface; the T488TM is designed for standard tool holders that accept a 16 mm shaft. How is the insert secured in the holder? Clamping is achieved with an M4x10 Torx screw; a T15 key is used for tightening to the recommended torque to ensure repeatable seating. Is the 90° angle suitable for shoulder machining? Yes, the 90° cutting angle is intended for precise shoulder and face turning, providing accurate right‑angle profiles with minimal secondary operations. Can the head be used with non‑Walter inserts? The T488TM is specified for Walter LNGX 1307 inserts; alternative insert types require verification of seat geometry and secure clamping compatibility. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high‑precision toolholder that combines a 90° cutting angle with secure Torx fastening for consistent shoulder milling. Benefit from proven compatibility with LNMX 1006 indexable inserts and the reliable supply chain of Metav Werkzeuge for rapid delivery and expert advice. Corner milling head by Teknik Makina — 90° indexable head, Ø40 mm A corner milling head designed for square shoulder and face milling using LNMX 1006 indexable inserts, combining compact dimensions with robust fastening for production environments 90° cutting angle for square shoulder milling Compatible with LNMX 1006 indexable inserts Ø 40 mm head with five cutting edges 16 mm shank; Torx M3x7 screw, T8 key Precision seating and predictable machining results The compact milling head delivers precision by securing the insert in a repeatable seat that reduces run‑out and positional variation. With a defined 90° cutting geometry and a head diameter of Ø40 mm, the design supports accurate shoulder and corner cuts where dimensional conformity is critical. The use of indexable plates keeps maintenance straightforward: worn inserts are replaced, not the entire tool, which helps preserve shaft alignment and machine setup times. Simple, secure clamping for fast tool changes Fastening is achieved with a Torx screw (M3x7) operated with a T8 key, ensuring a secure clamp without complex procedures. The head accepts LNMX 1006 plates (Korloy‑compatible), a widely used insert format that allows rapid changeover and consistent cutting performance. For workshops unfamiliar with indexable systems, an indexable head holds replaceable carbide plates at a fixed angle so the cutting edge is restored instantly when an insert is rotated or replaced. Robust geometry for stable cutting and repeatability Equipped with five cutting edges across the head, the toolholder focuses on balanced engagement and stable chip removal under intermittent loads. The combination of a 90° approach and the head’s dimensions is optimised for repeatable results in series production, helping to reduce scrap rates and rework. The 16 mm shank delivers a compact footprint that supports rigid mounting while keeping the overall tool projection modest, which reduces deflection during heavier passes. Integration into the workshop and supply reliability The toolholder’s compact overall length and clear mechanical data simplify tool setup and inventory management in a production shop. Supplied by Teknik Makina and distributed via Metav Werkzeuge, the component benefits from a central European quality filter and dependable logistics. For procurement and planning, the clear compatibility with LNMX 1006 inserts and Korloy plates allows standardised stocking of inserts and fastening consumables, keeping toolrooms efficient and predictable. For Teknik Makina products such as this 90° corner milling head, contact Metav Werkzeuge for specific availability, delivery options and tailored recommendations — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: T386TM Manufacturer: Teknik Makina For inserts: LNMX 1006 indexable inserts (Korloy compatible) Manufacturer SKU: T386TM Facts Shank diameter: 16 mm Head diameter: 40 mm Overall length: 40 mm Weight: 0.258 kg Cutting angle: 90° Number of cutting edges: 5 Special features Torx screw M3x7 Torx key size T8 Compatible with Korloy LNMX 1006 inserts FAQ Which insert type fits this head? The head accepts LNMX 1006 indexable inserts; Korloy plates have been specified as compatible. What is the shank diameter of the toolholder? The shank diameter is 16 mm, matching the recorded uptake dimension for compact mounting. Which fastening hardware is required? Fastening uses an M3x7 Torx screw tightened with a T8 key for secure insert clamping. What cutting angle does the head provide? The toolholder provides a 90° cutting angle, suited to square shoulder and corner milling operations. How many cutting edges are present on the head? The head has five cutting edges designed into the assembly for balanced engagement. What is the SKU and who supplies the tool? The SKU is T386TM; the head is produced by Teknik Makina and supplied via Metav Werkzeuge. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of compact design and coolant-through performance for steady turning cycles; the internal coolant and compatibility with ADMT 1606 indexable inserts reduce tool change time and improve process reliability. Order directly via Metav Werkzeuge or contact our consultants for application advice. Corner tool head for ADMT 1606 indexable inserts — 40 mm diameter, internal coolant (Teknik Makina) The Corner tool head is a compact turning tool head for ADMT 1606 indexable inserts, engineered for coolant-through operation and constrained-space machining with a 45 mm overall length Compact 40 mm diameter for tight operations Internal coolant for improved tool life Compatible with ADMT 1606 indexable inserts Four cutting edges for extended service Precision and compatibility for accurate turning The modular design delivers a consistent clamping interface for ADMT 1606 indexable inserts, enabling quick insert changes and repeatable positioning. With a 40 mm diameter and a 45 mm overall length the holder is suited to restricted setups where rigid support is essential. The combination of compact dimensions and standard insert geometry shortens set-up time and reduces the number of toolholders required in a small-to-medium sized workshop, improving process efficiency and machine uptime. Coolant-through design that stabilises cutting conditions Equipped with internal coolant, the holder channels cutting fluid directly to the insert seat to lower temperatures and assist chip control, which is particularly beneficial on continuous turning operations. The secure fastenings use a Torx T15 drive and an M4x10 Torx screw to ensure steady clamping of the insert, reducing the risk of micro-movements under load. This setup supports longer tool life and more consistent surface finishes by maintaining a stable cutting zone and effective heat management. Workshop-ready handling and proven build quality Manufactured by Teknik Makina, the tool head combines lightweight handling (approx. 0.258 kg) with robust construction for everyday use on production lathes. The four cutting edges extend service intervals, while compatibility with insert supplier Walter ensures broad availability of cutting grades and geometries. The result is a versatile, maintenance-friendly tool holder that lowers inventory complexity and helps maintain a steady throughput in industrial and jobbing environments. Discuss the Teknik Makina corner tool head (SKU T351-1TM) with Metav Werkzeuge for tailored recommendations and fast supply from Emmerich; our specialists will help match the holder to the right ADMT 1606 insert and machining task. Technical data SKU: T351-1TM Manufacturer: Teknik Makina Product type: Corner tool head ECLASS: 21181015 Facts Diameter: 40 mm Overall length: 45 mm Weight: 0.258 kg Cutting edges: 4 Cutting angle: 90° Features Internal coolant: yes Compatible inserts: ADMT 1606 Compatible insert manufacturer: Walter Torx key: T15 Torx screw: M4x10 Label: 40mm Eckmesserkopf ADMT 1606 L45mm mit Innenkühlung FAQ Is this holder compatible with ADMT 1606 inserts? Yes. The Teknik Makina corner tool head (SKU T351-1TM) is designed specifically for ADMT 1606 indexable inserts and provides the correct seating and clamping geometry for secure use. Does the tool head provide internal coolant? Yes. Internal coolant is integrated into the holder to deliver coolant directly to the cutting edge, improving thermal control and chip evacuation during turning operations. What fastening method is used to secure the insert? The insert is secured with a Torx screw; the holder uses a Torx T15 drive and an M4x10 screw for reliable clamping. How many cutting edges are available per insert position? The tool head accepts inserts in a configuration that provides four cutting edges, extending service life before a re-index is required. Is the holder suitable for machine shops with limited overhang? Yes. With a compact 40 mm diameter and 45 mm overall length the corner tool head is optimised for confined setups and restricted overhangs. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a compact 40 mm cutter diameter, internal coolant and a robust 90° cutting geometry to ensure predictable cycle times and controlled chip flow; order the tool directly via Metav Werkzeuge or consult our team for specification advice. T241-1TM corner milling head — 40 mm indexable milling head with internal coolant for APMT 1604 by Teknik Makina T241-1TM corner milling head is designed for precision square-shoulder milling and profiling in CNC operations where reliable chip evacuation and quick insert changes are essential 40 mm cutter diameter with 90° cutting angle Internal coolant for improved chip evacuation Compatible with APMT 1604 inserts (Korloy) Torx T15 screw M4x10, 4 cutting edges Consistent production through designed geometry and coolant The compact tool body combines a 40 mm cutter diameter with a 90° cutting angle to deliver stable engagement and repeatable results on shoulder and profile passes. The short 45 mm overall length reduces overhang and helps maintain rigidity in medium-duty milling operations, which stabilises cutting forces and supports longer insert life. With a balanced mass of 0.258 kg, the head contributes to reduced vibration and consistent surface finish, while the geometry supports predictable toolpaths that enhance cycle-time reliability. Faster operations and less downtime through coolant-fed inserts Built-in internal coolant supplies cutting fluid directly to the cutting zone, improving chip breaking and evacuation at the tool edge. This feature is particularly significant when using APMT 1604 indexable inserts, enabling stable cutting at higher feed rates and cleaner chip control. The secure clamping system uses a Torx T15 key and M4x10 screw to fix inserts reliably; this permits rapid insert replacement and lowers maintenance intervals, thereby increasing machine uptime and reducing process interruptions. Versatility for confined and precise machining tasks As an indexable milling head, the component suits operations that require square-shoulder cutting and accurate profiling while keeping tool inventory minimal. The compatibility with Korloy inserts expands available grades and geometries for finishing or light roughing, allowing the tool to be adapted to different material demands without changing the tool body. The compact dimensions make the head appropriate for setups with limited clearance, enabling access to tight pockets and stepped shoulders while preserving stiffness. Practical handling and workshop integration The head’s straightforward interface and common fastener standard simplify procurement and servicing in busy shops. The T241-1TM designation aids ordering and stock management, while the indexable insert format supports cost-efficient reconditioning of cutting edges rather than whole-tool replacement. Together with Metav’s distribution from Emmerich, customers benefit from reliable supply and clear specification support, ensuring the head integrates smoothly into existing production toolsets. Contact Metav Werkzeuge to specify the Teknik Makina T241-1TM corner milling head with internal coolant for streamlined machining and dependable deliveries from Emmerich Technical Data SKU: T241-1TM Product type: Corner milling head Manufacturer: Teknik Makina ECLASS: 21181015 Facts Cutter diameter: 40 mm Overall length: 45 mm Weight: 0.258 kg Cutting edges: 4 Cutting angle: 90° Compatibility & features Internal coolant: Yes Indexable inserts: APMT 1604 Compatible insert manufacturer: Korloy Torx key: T15 Torx screw: M4x10 FAQ Which inserts fit this milling head? This milling head accepts APMT 1604 indexable inserts; Korloy grades are listed as compatible and offer a broad range of chipbreakers and coatings suitable for different finishes. Is internal coolant supplied through the tool body? Yes, the head is equipped with internal coolant, which directs cutting fluid to the insert edge to aid chip control and surface quality during milling. What is the overall length and how does it affect rigidity? The head has a compact overall length of 45 mm, reducing overhang and improving rigidity compared with longer tool assemblies, which contributes to steadier cuts and better finish. Which fastening standard secures the inserts? Inserts are secured with a Torx T15 drive and M4x10 screw, facilitating secure clamping and straightforward replacement using common workshop tools. How heavy is the tool and what does that mean for handling? At 0.258 kg, the head is lightweight yet sufficiently robust for stable operation, simplifying handling during tool changes and stocking while maintaining cutting stability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a 90° cutting geometry, compact 40 mm diameter and fast, secure insert clamping for consistent corner turning performance. Order the Corner Tool Head T397TM directly via Metav Werkzeuge or ask our consultants if needed. Corner Tool Head T397TM — 40 mm diameter, for 3PKT 1505 indexable inserts (Teknik Makina) The Corner Tool Head is designed for precise external and face turning tasks, accepting 3PKT 1505 indexable inserts for efficient cornering and profiling in general machining operations. Compact 40 mm diameter tool head Compatible with 3PKT 1505 indexable inserts 90° cutting geometry for accurate corner turning Stable geometry for repeatable corner turning The tool head’s 90° cutting angle and compact 40 mm diameter are engineered to deliver consistent part geometry when performing corner and shoulder operations. A solid 16 mm shank and a mass of 0.268 kg contribute to reduced vibration and improved surface finish; this translates into fewer rejects and less rework in batch production. The rigid configuration stabilises the cutting zone, enabling predictable tool life and steady dimensional results even on interrupted cuts. Fast insert changes and secure clamping for productive setups Designed for use with 3PKT 1505 indexable inserts (compatible with Taegutec), the head accepts inserts that can be indexed quickly to restore a fresh cutting edge without losing setup accuracy. Clamping is achieved via an M4x10 Torx screw, driven with a Torx T15 key, which simplifies maintenance and reduces downtime compared with welded or brazed tooling. Indexable inserts lower per-edge costs and make reconditioning straightforward, so tool costs are distributed over multiple edges rather than a single component. Practical benefits in workshop and small-series production The compact overall length of 40 mm and the modest weight make the head suitable for confined toolpost spaces and quick toolchanger setups. With four cutting edges indicated, the configuration supports repeated indexing cycles before replacement is necessary, improving cost-efficiency on short to medium production runs. The straightforward mechanical design keeps maintenance work minimal while preserving machining accuracy, which is particularly beneficial for workshops seeking dependable tooling without complex upkeep. Contact Metav Werkzeuge today to confirm compatibility, request delivery details and secure Corner Tool Head T397TM units from our Emmerich supply for immediate integration into production. Technical data Article number: T397TM Designation: Corner tool head For indexable inserts: 3PKT 1505 (Taegutec) Facts Diameter: 40 mm Overall length: 40 mm Shank diameter: 16 mm Weight: 0.268 kg Cutting angle: 90° Number of cutting edges: 4 Torx key: T15 Torx screw: M4x10 Special features Compatibility: Taegutec 3PKT 1505 inserts Compact design for confined toolpost spaces Secure Torx clamping for fast insert replacement FAQ Which inserts fit this tool head? The Corner Tool Head T397TM is specified for 3PKT 1505 indexable inserts, with compatibility tested for Taegutec insert grades. What drive and screw are required for clamping? Clamping uses an M4x10 Torx screw tightened with a Torx T15 key for secure and repeatable insert fixation. Is the head suitable for heavy roughing cuts? The compact 40 mm diameter and rigid 16 mm shank provide stability for many turning tasks; for heavy roughing, assessment of machine power and cutting parameters is recommended to match the intended application. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, 90° turning solution with internal coolant and a precise 40 mm tool interface for reliable corner machining — built for ADKT 1706 indexable inserts. Order directly via Metav Werkzeuge or consult our specialists for integration advice. Corner tool head for ADKT 1706 indexable inserts — 40 mm diameter, internal coolant The Corner tool head is designed for accurate 90° turning and corner operations using ADKT 1706 indexable inserts, offering internal coolant for improved tool life and chip control. 40 mm diameter for compact setups Integrated internal coolant for chip evacuation Compatible with Korloy ADKT 1706 inserts Four indexable cutting positions for longer runtime Torx T15 screw, M4x10 fastening Consistent 90° turning for repeatable part quality Designed for right‑angled turning tasks, this head delivers precise 90° geometry and stable tool positioning to support consistent batch production. The built‑in internal coolant supplies cutting fluid directly to the cutting edge, reducing thermal distortion and improving insert life; this means fewer interruptions for tool changes and steadier tolerances across runs. The compact 40 mm footprint allows use in confined toolposts without compromising rigidity. Faster changeover and dependable clamping to reduce downtime Maintenance and insert changes are simplified by the standardised Torx T15 drive and the M4x10 clamping screw, enabling quick, reproducible clamping actions. With four indexable faces, the head offers multiple reuse positions per insert, translating into longer intervals between tool replacements. The robust clamping arrangement and precise screw interface reduce the risk of seating errors, supporting higher machine uptime and predictable process behaviour. Broad workshop compatibility and clearer process control Engineered to accept Korloy ADKT 1706 indexable inserts, the head integrates seamlessly into common turning tool chains and is suited for a range of finishing and light‑turning operations. The combination of compact dimensions and internal coolant ensures effective chip control and coolant delivery even on small lathes and live‑tool setups. Clear, measurable properties and a familiar fastener system make process documentation and operator training straightforward. Choose Teknik Makina engineering for dependable corner machining and contact Metav Werkzeuge for tailored advice and ordering: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: T589TM Eclass: 21181015 Product type: Corner tool head Facts Diameter: 40 mm Overall length: 40 mm Weight: 0.248 kg Cutting edges: 4 Cutting angle: 90° Internal coolant: yes Torx key: T15 Clamping screw: M4x10 Special features Compatible with ADKT 1706 indexable inserts Suited for Korloy insert manufacturer Compact design for confined toolposts Designed for repeatable, high‑uptime operation FAQ What inserts are compatible with this tool head? The corner tool head accepts ADKT 1706 indexable inserts, specifically those from Korloy as stated in the product data. Is there coolant supply integrated in the head? Yes, the head incorporates internal coolant, which delivers cutting fluid directly to the cutting zone for improved insert life and chip control. How many usable cutting positions does the head provide? The design provides four indexable cutting positions, allowing multiple rotations of the insert before replacement. Which fastener is required for insert clamping? Insert clamping is achieved with an M4x10 screw tightened using a Torx T15 driver for reliable, repeatable seating. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of compact design, internal coolant and a stable 90° cutting geometry for predictable, high-quality turning results; order the tool directly via Metav Werkzeuge or consult our specialists for integration advice. Corner Tool Head T214-1TM for ADMT 1204 Indexable Inserts — 40 mm, Internal Coolant (Teknik Makina) The Corner Tool Head T214-1TM is a precision turning head designed for use with ADMT 1204 indexable inserts, providing internal coolant and a 90° cutting angle for consistent shoulder and profile machining in CNC turning operations. 40 mm diameter for compact setups Internal coolant for improved chip evacuation Four cutting edges for extended service life 90° cutting angle for precise shoulder machining Maximise cutting performance with predictable geometry The T214-1TM delivers stable cutting thanks to its 90° cutting angle and optimised seating for ADMT 1204 indexable inserts, which together reduce vibration and produce consistent surface finishes on shoulders and profiles. By combining a short overhang with a 40 mm diameter body and a compact 45 mm overall length, the tool head reduces deflection and improves dimensional repeatability. These factors translate into fewer reworks and more reliable cycle times, supporting efficient production scheduling and lowered per-part costs. Maintain process integrity with coolant-through design Equipped with internal coolant, the head directs cutting fluid close to the cutting edge, improving chip evacuation and heat control. This targeted coolant supply extends insert life and helps maintain cutting-edge stability during longer runs. For materials and operations where thermal management is critical, the coolant-through arrangement reduces built-up edge and improves surface integrity without complex setup changes. The result is a more robust cutting process and reduced frequency of tool changes. Compact, service-friendly construction for rapid upkeep Designed for tight toolpost spaces, the compact dimensions and modest weight (0.28 kg) make the head straightforward to handle and position. Fast maintenance is supported by the standard Torx screw M3x7 and Torx key T8, enabling quick insert indexation and clamp operations. The four cutting edges per insert minimise downtime for replacements and lower tooling consumption over production runs. Integration into existing holders is simplified by the standard interface and clear fitment for ADMT 1204 inserts supplied by Walter. Reliable compatibility for workshop and production use Compatibility with ADMT 1204 indexable inserts (Walter) ensures access to a broad range of grades and chipbreakers for different materials and cutting conditions. The T214-1TM is suitable for shoulder and profile tasks in CNC turning centres where repeatable results and straightforward maintenance are required. With its balanced combination of geometry, coolant supply and compact form factor, the tool head supports steady production output and predictable tool-life planning, making it a pragmatic choice for both jobbing shops and series manufacture. Choose Teknik Makina's corner tool head for dependable shoulder turning and contact Metav Werkzeuge for ordering or integration support; Metav's specialists are available at info@metav-werkzeuge.com or +49 2822 7131930 to advise on compatibility and tooling strategies. Technical data SKU: T214-1TM Label: 40mm Eckmesserkopf ADMT 1204 L45mm mit Innenkühlung Manufacturer: Teknik Makina Facts Diameter: 40 mm Overall length: 45 mm Weight: 0.28 kg Cutting angle: 90° Cutting edges: 4 Special features Internal coolant Compatible with ADMT 1204 indexable inserts (Walter) Torx screw: M3x7, Torx key: T8 Compact design for limited toolpost space FAQ How does internal coolant improve machining with this tool head? The internal coolant on the Corner Tool Head T214-1TM supplies fluid directly to the cutting zone, aiding chip evacuation and reducing heat at the edge, which helps to extend insert life and stabilise cutting performance. Which inserts are compatible with the tool head? This turning head is designed for ADMT 1204 indexable inserts; compatibility with Walter-manufactured inserts is confirmed for a wide selection of grades and chipbreaker options. What size and weight should be expected for setup planning? The head has a 40 mm diameter, a 45 mm overall length and weighs 0.28 kg, making it suitable for compact installations with reduced overhang. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine the compact 40 mm design with internal coolant to secure stable chip control, precise insert seating and reduced setup time; order the corner tool head directly via Metav Werkzeuge or ask our consultants if needed. Corner Tool Head for ANKX 1706 Indexable Inserts — 40 mm, internal coolant (Teknik Makina T440-1TM) Corner Tool Head is a 40 mm turning head engineered for ANKX 1706 indexable inserts, providing internal coolant and a compact 45 mm overall length for tight turning operations 40 mm diameter for compact machining Internal coolant for improved chip control Compatible with ANKX 1706 ISCAR indexable inserts Three cutting edges; Torx T20 M5x12 fixing Consistent turning performance in a compact package The compact tool head combines a 40 mm diameter with a 45 mm overall length to suit confined setups without compromising rigidity. The design accepts ANKX 1706 indexable inserts and secures them positively with the M5x12 Torx screw, tightened with a Torx T20 key. With a 90° cutting angle and three cutting edges, the head supports stable cutting geometry and repeatable insert positioning; this reduces the need for frequent readjustment and contributes to shorter setup cycles. The modest mass (0.279 kg) keeps tool overhang manageable and helps maintain concentricity during external turning. Internal coolant for controlled chip evacuation and thermal stability Integrated internal coolant directs cutting fluid close to the cutting zone, improving chip control and helping to manage temperatures at the insert edge. This targeted cooling lowers the risk of thermal distortion in small-diameter operations and can extend insert life by reducing heat-related wear. For workshops seeking reliable, repeatable results in series production or precision single-part work, the coolant channel is a practical advantage that helps maintain surface quality while supporting longer uninterrupted runs. Secure fixing and workshop efficiency The head uses a standard Torx T20 connection with an M5x12 screw to clamp inserts firmly, reducing the risk of movement under load and simplifying reassembly during insert changes. The compact format and familiar fixing method contribute to lower cycle times for tool changes and predictable clamping forces across shifts. Supplied under the Teknik Makina designation and available as SKU T440-1TM, this head fits seamlessly into established tooling arrays, supporting standardisation in toolrooms and consistent logistics from stock in Emmerich. Contact Metav Werkzeuge today to request the Teknik Cutting Tools corner tool head T440-1TM with internal coolant and to receive tailored technical advice from our Emmerich team Technical data SKU: T440-1TM Product type: Corner tool head Brand: Teknik Makina ECLASS: 21181015 Label: 40mm Eckmesserkopf ANKX 1706 L45mm mit Innenkühlung Facts Diameter: 40 mm Overall length: 45 mm Weight: 0.279 kg Cutting edges: 3 Cutting angle: 90° Special features Internal coolant: true Compatible inserts: ANKX 1706 Compatible insert manufacturer: ISCAR Torx screw: M5x12 Torx key: T20 Manufacturer: Teknik Makina FAQ Which indexable inserts fit this tool head? The head is designed for ANKX 1706 indexable inserts and is compatible with inserts produced by ISCAR for the ANKX 1706 series. Does the head provide internal coolant? Yes — internal coolant channels are integrated to deliver cutting fluid directly to the cutting edge for improved chip evacuation and temperature control. How are the inserts secured? Inserts are clamped using an M5x12 Torx screw; a Torx T20 key is required for tightening to the specified torque. Is the design suitable for compact turning applications? The 40 mm diameter and 45 mm overall length make the head well suited to tight turning setups where rigidity and short overhang are priorities. What are the SKU and manufacturer details for ordering? The product is listed as SKU T440-1TM and supplied by Teknik Cutting Tools (Teknik Makina) Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, coolant-fed solution that combines 40 mm diameter precision with a true 90° cutting angle, ensuring reliable square-shoulder machining and consistent surface finish; order the component directly via Metav Werkzeuge or consult our specialists for application advice. Corner tool head — 40 mm, internal coolant, for APMT 0903 indexable inserts (Teknik Makina) The corner tool head is a coolant-fed indexable insert holder designed for square-shoulder turning and compact tool setups, compatible with APMT 0903 indexable inserts and optimised for repeatable shoulder and face operations. 40 mm diameter for compact installations Internal coolant for improved chip evacuation Compatible with APMT 0903 Korloy inserts 90° cutting angle for square-shoulder machining Accurate square shoulders with compact geometry The holder’s compact 40 mm diameter and precisely maintained 90° cutting angle translate into consistent shoulder dimensions and reduced manual rework on repeat production runs. The design supports stable insert seating, which limits vibration and enhances surface finish; this predictable geometry is particularly beneficial when tight tolerances matter and when set-up times should be minimised. The combination of compact form and rigid construction enables efficient use on multi-tool turrets and small-lathe configurations without sacrificing repeatability. Coolant-fed design for extended tool life and cleaner cuts An integrated internal coolant channel directs cooling and lubrication precisely to the cutting edge, lowering thermal load and aiding chip control during interrupted cuts. This focused coolant supply reduces flank wear and helps preserve insert geometry, extending service intervals and cutting costs per component. For operations that demand controlled chip evacuation—especially in shoulder and face turning—the coolant-fed approach improves machining stability and supports more consistent cycle times under moderate to high cutting parameters. Compatibility that simplifies tooling logistics This indexable insert holder accepts APMT 0903 inserts and is compatible with Korloy-manufactured grades, easing stock management where those inserts are already in use. Fast replacement is ensured via the supplied Torx fastening system (Torx key T8; screw M2.5x5.5), allowing quick insert changes and minimising machine downtime. The unit’s compact overall length and standard interface simplify integration into existing tool stations, while the proven fastening specification supports secure clamping through repeated changeovers. Production-ready build for reliable operation Engineered by Teknik Makina with a focus on workshop durability, the holder’s lightweight yet robust construction (approx. 0.248 kg) and 40 mm overall length make it suitable for high-mix, space-constrained production environments. The design reduces inertia on the turret, improving acceleration and deceleration in CNC sequences and helping to maintain part accuracy across long runs. Clear interchangeability with APMT 0903 indexable inserts supports flexible process planning and rapid response to changing production demands. For coolant-fed corner machining from Teknik Makina, contact Metav Werkzeuge in Emmerich for tailored advice and secure procurement; our specialists will help confirm fitment and application details to integrate this holder into your workflow. Technical data SKU: T239-1TM Manufacturer: Teknik Makina Product type: Corner tool head Key specifications Diameter: 40 mm Overall length: 40 mm Weight: 0.248 kg Cutting edges: 5 Cutting angle: 90° Materials & features Internal coolant: yes Compatible inserts: APMT 0903 Compatible insert maker: Korloy Torx key: T8 Torx screw: M2.5x5.5 eClass: 21181015 FAQ Which insert type fits this tool head? The corner tool head accepts APMT 0903 indexable inserts; Korloy grades are listed among compatible manufacturers for this holder. Is the tool head suitable for shoulder turning on small lathes? Yes, the 40 mm compact geometry and 90° cutting angle make the holder well suited to square-shoulder turning on compact and medium-sized lathes. Does the unit provide coolant to the cutting edge? The holder features internal coolant, supplying lubricant and cooling directly to the insert tip to improve chip control and reduce thermal wear. What fastening hardware is required for insert clamping? Insert clamping uses a Torx fastening system: Torx key T8 and screw M2.5x5.5 are specified for secure and repeatable assembly. Can the holder be retrofitted into existing turret stations? The holder’s standard compact dimensions and fastening interface allow integration into common turret stations, subject to turret clearance and mounting compatibility. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the high rigidity of a 40 mm cutting head combined with internal coolant for improved surface finish and controlled chip evacuation; the compatibility with APMT 11T3 indexable inserts ensures easy tool management and reproducible results. Order directly via Metav Werkzeuge or request technical advice from the consultants for a streamlined integration into existing turning operations. Corner tool head — 40 mm with internal coolant for APMT 11T3 (Teknik Makina) Corner tool head for APMT 11T3 indexable inserts is a compact, coolant-fed cutting head designed for precision turning operations where chip control and repeatable edge location are essential. 40 mm diameter for compact tool setups Internal coolant for stable chip evacuation Compatible with APMT 11T3 indexable inserts 16 mm shank for secure mounting Improved process stability and surface quality through coolant-fed design The coolant-fed design brings measurable advantages for continuous turning applications. With a 40 mm tool diameter and integrated internal coolant, heat at the cutting zone is reduced and chips are directed away from the insert, which helps to maintain a consistent cutting edge temperature and prolong tool life. The head’s 90° cutting angle supports reliable corner machining and predictable tool engagement, resulting in a better surface finish and fewer rework cycles. These technical characteristics translate directly into lower process variability and more efficient cycle times on batch production. Precise mounting and straightforward maintenance for efficient shopfloor routines A solid interfacing geometry with a 16 mm shank provides a stable connection to modular holders and reduces vibration during heavy cuts. The fastenings use a T8 Torx key and M2.5×5.5 screw, which enables quick insert clamping and replacement without special tooling. Compatibility with Korloy-branded APMT 11T3 inserts simplifies logistics and reduces inventory complexity, as commonly available indexable inserts can be used across multiple tool stations. The compact mass (approx. 0.22 kg) helps to balance assemblies while still offering sufficient rigidity for accurate turning operations. Designed for industrial use and predictable integration into production Manufactured by Teknik Makina, this corner cutting head is built for repeatability and everyday industrial demands. The configuration with five cutting edges supports flexible insert indexing strategies, lowering unit costs per cutting edge. Classification and traceability are supported through the included SKU and eClass identifiers, ensuring the component can be specified precisely in procurement and tool lists. For complex setups or specific application advice, Metav Werkzeuge provides technical consultancy and local stock support from Emmerich, helping to reduce lead times and simplify supply chains. For technical specification checks, driven applications, or to arrange immediate supply of the Teknik Makina corner tool head (SKU T250-1TM), contact Metav Werkzeuge for expert guidance and availability from Emmerich. Technical Data SKU: T250-1TM UID: T250-1TM Product type: Corner tool head Manufacturer: Teknik Makina eClass: 21181015 Compatible inserts: APMT 11T3 Facts Diameter: 40 mm Shank diameter: 16 mm Overall length: 40 mm Weight: 0.22 kg Cutting angle: 90° Cutting edges: 5 Torx screw: M2,5x5,5 Torx key: T8 Special features Internal coolant Compatible insert manufacturer: Korloy Application: precision turning with indexable inserts FAQ Which indexable inserts fit this cutting head? The corner tool head is designed for APMT 11T3 indexable inserts; Korloy-compatible grades are listed as compatible for straightforward procurement. Does the tool head provide internal coolant? Yes, the cutting head features internal coolant, which improves chip evacuation and temperature control at the cutting edge. What is the mounting diameter required for the tool head? A 16 mm shank diameter is specified for the mounting interface to ensure stable clamping in suitable holders. Which fastener and key are used for insert clamping? Insert clamping is achieved with an M2.5×5.5 Torx screw and requires a T8 Torx key for service and insert changes. What identifier should be used when ordering or specifying this tool head? Use SKU T250-1TM and the product description "corner tool head for APMT 11T3" to ensure accurate ordering. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Precise 90° shoulder turning with integrated coolant and secure T8 Torx fastening ensures stable chip control and reduced tool wear; compatible with LNMX 1006 Korloy indexable inserts for flexible applications. Order the corner head directly via Metav Werkzeuge or consult their advisors for selection support. Corner Head T386-1TM — 40 mm corner turning head with internal coolant for LNMX 1006 indexable inserts (Teknik Makina) Corner Head T386-1TM is a compact 40 mm turning head engineered for accurate right‑angle shoulder cuts using LNMX 1006 inserts, featuring internal coolant for improved thermal control and a secure T8 Torx mounting system. 40 mm diameter head, 90° cutting angle Internal coolant for consistent cooling Fits LNMX 1006 Korloy indexable inserts Secured with T8 Torx screw M3x7 Accurate 90° shoulders and improved tool life The 40 mm diameter head with a defined 90° cutting angle provides consistent shoulder profiles and repeatable geometric accuracy in production turning. Internal coolant channels deliver cutting fluid directly to the insert edge, reducing thermal load and promoting controlled chip formation. This results in extended insert life and more predictable process windows, which benefits batch production and high‑precision jobbing alike. The combination of angle stability and targeted cooling supports higher productivity without sacrificing component tolerances. Secure clamping for repeatable set‑ups A robust fastening system, using a T8 Torx drive and M3x7 screw, guarantees reliable clamping of the indexable insert under machining loads. The deliberate choice of a Torx interface minimises cam‑out and enables consistent torque during changeovers, reducing the risk of incorrect seating. For workshops seeking short set‑up times and reproducible tool performance, this configuration lowers the probability of vibration‑related defects and simplifies routine maintenance. Compact form factor that adapts to tight machines With a compact overall length and a head diameter of 40 mm, this turning head keeps overhang to a minimum and suits machines with limited clearance. The modest mass of 0.258 kg helps to reduce spindle load and dynamic imbalance, particularly on smaller lathes or multispindle arrangements. Compatibility with LNMX 1006 Korloy indexable inserts provides access to commonly stocked inserts, easing logistics and enabling rapid replacement during production. Practical suitability and operational guidance Designed by Teknik Makina for shoulder turning tasks, the head supports straightforward integration into existing tool setups and is particularly suitable for high‑precision small to medium batch runs. Internal coolant requires appropriate machine coolant lines; when fitted correctly, the coolant channel significantly improves chip evacuation and surface finish. Routine checks of the Torx screw torque and insert seating are recommended to maintain consistent cutting performance and maximise service life. Contact Metav Werkzeuge for tailored advice on integrating the T386-1TM into production or to discuss compatible inserts and machine fitments Technical data SKU: T386-1TM Product type: Corner turning head Manufacturer: Teknik Makina Compatible inserts: LNMX 1006 (Korloy) Internal coolant: Yes Core specifications Diameter: 40 mm Overall length: 40 mm Weight: 0.258 kg Cutting angle: 90° Torx key: T8 Torx screw: M3x7 Aufnahme diameter: 16 mm Features Internal coolant channel Designed for LNMX 1006 indexable inserts Secure Torx clamping Compact design for reduced overhang FAQ Which inserts are compatible with this corner head? The corner head accepts LNMX 1006 indexable inserts; Korloy inserts in this format are compatible with the T386-1TM. Is the tool suitable for automated coolant systems? Yes, the integrated internal coolant channel is intended for use with machine coolant provision to improve chip evacuation and tool life. What fastening method is used for the insert? Insert clamping is achieved via a Torx screw (T8) using an M3x7 screw in the T386-1TM to ensure repeatable and secure seating. How does the head geometry affect shoulder finishing? The 90° cutting angle produces precise right‑angle shoulders with consistent dimensional control, especially when combined with correct insert selection and coolant flow. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com