Gibt es einen Hahn und Kolb Online Shop?

Take advantage of a compact, indexable solution that combines reliable clamp stability and easy insert changes for fast, repeatable internal machining. The tool’s 20 mm shank and 55 mm effective cutting length deliver improved rigidity and consistent finishes while the CCMT insert interface keeps tooling costs low — order the boring bar directly via Metav Werkzeuge or consult our specialists for application advice. TKB106TM boring bar — indexable internal boring tool with CCMT interface (Teknik Makina) The TKB106TM boring bar is designed for precision internal machining in workshop and production environments, accepting CCMT 09T3 indexable inserts for adaptable finishing and roughing operations Indexable insert holder for CCMT 09T3 20 mm shank for secure toolholder clamping 55 mm effective cutting length Suitable for bores up to 38 mm diameter Greater cutting stability through a compact, precision shank The bar’s 20 mm shank and balanced mass (0.378 kg) increase rigidity at the holder, which reduces vibration and improves concentricity during internal turning. A firmer support in the toolpost translates directly into more consistent bore diameters and longer insert life. For workshops seeking repeatable results, this means fewer reworks and more predictable cycle times — the result of combining a well-dimensioned shank with a compact overall length. Efficient insert system that lowers operating costs Equipped to accept CCMT 09T3 indexable inserts, the boring bar enables quick insert replacement without regrinding, cutting downtime and consumable costs. CCMT inserts are a widely used grade for finishing and semi-finishing; using them allows an operator to restore cutting performance in minutes. This modular approach delivers a clear economic benefit on production runs where frequent edge restoration would otherwise interrupt throughput. Effective cutting reach with controlled overhang for precision bores The 55 mm effective cutting length and total length of 105 mm balance reach and stiffness, supporting machining of medium-deep bores while limiting overhang-related deflection. With a maximum cutting diameter parameter indicating suitability up to 38 mm, the bar fits common internal turning tasks across automotive, hydraulic and general engineering components. The design focuses on delivering predictable tool behaviour so that setup times are reduced and process stability is improved. Choose Teknik Cutting Tools’ TKB106TM via Metav Werkzeuge for dependable internal machining — contact Metav Werkzeuge for tailored application support and ordering guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: TKB106TM Manufacturer: Teknik Makina Designation: Ausbohrwerkzeug Facts Cutting diameter max: 38 mm Shank diameter: 20 mm Effective cutting length: 55 mm Overall length: 105 mm Weight: 0.378 kg Compatible insert: CCMT 09T3 Special features Indexable insert interface CCMT 09T3 Compact construction for improved rigidity Nominal diameter reference: 28 Suitable for precision internal machining FAQ What insert type does the boring bar use? The boring bar accepts CCMT 09T3 indexable inserts, allowing fast edge changes and adaptable grades for finishing or semi-finishing. Which bore diameters are suitable for this tool? The bar is configured for internal bores up to 38 mm cutting diameter and is particularly effective where a moderate reach is required. How does the 20 mm shank affect machining performance? A 20 mm shank provides a secure clamp fit and improved rigidity, which reduces vibration and contributes to more consistent bore accuracy. Is the cutting length sufficient for medium-deep bores? With a 55 mm effective cutting length and 105 mm overall length, the tool offers a practical balance between reach and stiffness for many workshop applications. Can the bar be used for both finishing and roughing passes? Yes — paired with appropriate CCMT insert grades, the bar is suitable for semi-finishing and finishing operations where insert geometry and grade are selected to match the application. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust compatibility, high cutting stability and straightforward integration into existing toolholders for consistent bore quality; order directly via Metav Werkzeuge or consult the team for tailored toolset recommendations. Indexable insert drill – Ø 38 mm, SPMG 1104-compatible by Teknik Makina Indexable insert drill for medium to large diameter holes in industrial metalworking, designed for use with SPMG 1104 inserts and standard heavy-duty holders Indexable insert drill SPMG 1104 compatible Ø 38 mm for stable bore quality 76 mm cutting length for versatile hole depths 32 mm shank diameter with 58 mm holder length Reliable productivity for demanding bore operations The indexable insert drill combines a rigid body with a purpose-designed insert interface to deliver repeatable results in production. With a Ø 38 mm diameter and 76 mm cutting length, the tool is optimised for through and medium-depth blind holes where chip control and hole accuracy matter. The use of SPMG 1104 inserts allows fast corner changes and consistent cutting geometry, which reduces downtime and keeps cycle times predictable. The robust design supports high feed rates while maintaining hole straightness and surface finish, providing a measurable productivity gain on batch runs. Compatibility that reduces setup complexity Designed for common insert suppliers, the drill accepts inserts from Taegutec and YG-1, simplifying procurement and aftermarket flexibility. The 32 mm shank and 58 mm holder length match standard heavy-duty holders, enabling direct replacement in existing tool assemblies without special adaptors. Fewer tool changes and predictable clamping interfaces translate into lower setup time and improved machine utilisation. For workshops aiming to streamline tooling logistics, this compatibility lowers the risk of incorrect fittings and supports faster changeovers between jobs. Stability and durability for consistent hole quality Construction and mass distribution have been balanced to reduce vibration and maintain concentricity; the tool’s mass of 0.992 kg contributes to steadiness during cutting. The insert-based concept isolates wear to replaceable cutting edges, which preserves the main body and reduces long-term tooling costs. The drilled bore benefits from controlled chip evacuation and uniform cutting edge geometry, which helps achieve tighter tolerances and better surface integrity compared with ad hoc drilling solutions. Overall, the body is intended for repeated use under industrial conditions where consistency matters. Practical integration and workshop support The drill body is supplied ready for standard workshop use and is suitable for integration in turning and milling centres that accept indexable drills. Documentation and product images are available for verification prior to purchase. For specific material mixes or unusual clamping requirements, technical advice is recommended to ensure optimal insert grade and cutting data are selected. Metav’s sourcing approach aims to simplify precision: the tool can be matched with appropriate inserts and cutting parameters to meet individual production targets while maintaining supply reliability. Contact Metav Werkzeuge for a tailored tooling recommendation to integrate the Teknik Cutting Tools indexable insert drill Ø 38 mm (SKU U938TM) into existing production lines — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: U938TM Manufacturer: Teknik Cutting Tools E-class: 21180201 Facts Diameter: 38 mm Overall length: 173 mm Cutting length: 76 mm Shank diameter: 32 mm Shank length: 58 mm Weight: 0.992 kg Special features Compatible insert: SPMG 1104 Compatible insert manufacturers: Taegutec, YG-1 FAQ What insert type does the drill use? The drill uses SPMG 1104 indexable inserts; compatible manufacturers include Taegutec and YG-1 for easy sourcing. Can the drill be used for both through-holes and blind holes? Yes, the 76 mm cutting length supports a range of applications from through-holes to medium-depth blind bores when matched with suitable inserts. Which shank size is required for mounting? The tool has a 32 mm shank and a holder engagement length of 58 mm, matching common heavy-duty holders. Is the body suitable for high-feed applications? The drill body is designed for rigidity and stability, which supports higher feed rates while maintaining bore quality when correct inserts and speeds are applied. What is the SKU for ordering and reference? The SKU is U938TM; referencing this when enquiring ensures the correct indexable insert drill and compatible accessories are supplied. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of stable clamping, long effective cutting length and indexable-insert compatibility to keep bore-making cycles consistent and economical — order or request advice via Metav Werkzeuge for fast delivery and technical guidance. Teknik Makina Solid Drill U838TM — 38 mm diameter, indexable-insert design The Solid Drill U838TM is an indexable solid drill designed for medium-to-large bore production in industrial machining centres, offering a long cutting reach and secure 32 mm shank clamping for stable, repeatable performance. 38 mm cutting diameter 114 mm effective cutting length 32 mm shank for positive clamping Compatible with SPMG 1104 inserts Consistent cutting performance for deep bores The U838TM is engineered to deliver a high material removal rate across extended depths owing to its 114 mm cutting length and rigid tool geometry. Indexable-insert technology with SPMG 1104 plates reduces tool-change time and lowers life-cycle costs: worn inserts are replaced instead of the whole tool, improving uptime. The design supports stable chip formation and predictable wear, which simplifies process planning and helps maintain cycle-time targets in serial production. Mechanical stability that keeps cycles uninterrupted A substantial 32 mm shank and a 211 mm overall length provide the mechanical support required to minimise runout and vibration during plunge and pecking operations. This stability extends insert lifetime and improves hole quality, meaning fewer rework steps and reduced waste. The tool mass of 1.062 kg contributes to steady rotational momentum, which is beneficial when maintaining feed rates in continuous machining environments. Proven compatibility and straightforward servicing The drill is prepared for use with standard insert families and is listed as compatible with Taegutec and YG-1 insert suppliers, easing sourcing and stocking decisions. The SPMG 1104 indexable plates enable rapid replacement and uncomplicated set-up on holders that accept a 32 mm shank, helping to keep maintenance intervals short and predictable. Files and documentation are available for reference to support integration into existing tool inventories and CAM setups. For reliable production drilling with the Teknik Makina U838TM, contact Metav Werkzeuge for purchase and technical clarification — Metav’s Emmerich-based team provides rapid dispatch and practical procurement support via eMail info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data Article number: U838TM Manufacturer: Teknik Cutting Tools Product: Solid drill Dimensions & weight Diameter: 38 mm Effective cutting length: 114 mm Overall length: 211 mm Shank diameter: 32 mm Shank engagement length: 58 mm Weight: 1.062 kg Compatibility & features Insert type: SPMG 1104 Compatible insert makers: Taegutec, YG-1 eClass: 21180201 FAQ Which insert type is required for this drill? The Teknik Makina Solid Drill U838TM uses SPMG 1104 indexable inserts for cutting edge replacement. What is the maximum cutting length of the tool? The effective cutting length is 114 mm for the U838TM, allowing deep bore and extended-reach operations. Which shank size is required in the holder? A 32 mm shank holder is required; the tool has a 32 mm shank diameter with a 58 mm engagement length. Are inserts from other manufacturers usable? Inserts from Taegutec and YG-1 are listed as compatible with this design and can be used according to holder and seat specifications. What documentation is available for integration? Technical files have been provisioned and standard data (article number U838TM, dimensions and insert type) should be used for CAM setup and tool management Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust indexable drill that combines long cutting reach with secure clamping for stable, repeatable holemaking — compatible with Korloy WCM‑06T3 inserts. Order the tool directly via Metav Werkzeuge or consult their specialists for application advice. U638TM – Teknik Makina indexable drill, 38 mm diameter, 32 mm shank The U638TM is an indexable drill intended for CNC drilling tasks that demand extended cutting length and reliable insert coupling, suitable for industrial production environments and workshop use. 38 mm cutting diameter for deeper holes Compatible with Korloy WCM‑06T3 inserts 152 mm effective cutting length 32 mm shank for secure clamping Improved productivity through stable geometry and long reach The design delivers a 152 mm cutting length combined with a 249 mm total length, allowing deeper holemaking without changing tools as frequently. The extended reach reduces the number of setups and tool changes, which leads to shorter cycle times and higher machining throughput. Thanks to the 32 mm shank diameter and solid construction, the tool maintains axial and radial stability during prolonged cuts, helping to keep hole accuracy consistent across batches. Reduced downtime with indexable insert compatibility By accepting WCM‑06T3 insert plates from Korloy, the tool enables rapid insert replacement instead of full‑tool replacement. This saves maintenance time and permits quick reconditioning on the shop floor. The insert system supports consistent cutting edges and repeatable results, so the emphasis is on predictable component quality and easier inventory management of wear parts. Rigidity and handling designed for industrial use With a substantial mass of 1.43 kg and a robust clamping length of 58 mm, the drill is balanced for secure mounting and vibration damping on standard toolholders. The 32 mm shank ensures compatibility with common chucking systems and provides a reliable interface for transmitting cutting forces, which improves surface finish and roundness for through and medium‑depth holes. Practical benefits for production planning In machine shops where set‑ups and throughput matter, the combination of an extended cutting length and indexable inserts translates into a tangible improvement in operational efficiency. The tool’s nominal 38 mm diameter is a standard size that simplifies process planning and keeps fixturing requirements familiar. As a result, material removal rates can be optimised without compromising tool life or component tolerances. For precise guidance on integrating the U638TM into existing machining processes, or to arrange supply through Metav Werkzeuge, please contact Metav Werkzeuge GmbH at +49 2822 7131930 or info@metav-werkzeuge.com — specialists are available to advise on holder selection and insert stocks Technical Data Article number: U638TM Manufacturer: Teknik Makina Designation: Vollbohrer Facts Diameter: 38 mm Cutting length: 152 mm Shank diameter: 32 mm Shank length: 58 mm Total length: 249 mm Weight: 1.43 kg Special features Compatible with Korloy WCM‑06T3 inserts Indexable insert system Robust shank for secure clamping Suitable for CNC drilling operations FAQ What insert type fits this drill? The drill accepts WCM‑06T3 indexable inserts; compatibility is specified for Korloy insert plates. What are the key dimensions to check for holder selection? Important dimensions include a 38 mm diameter, 152 mm cutting length, 32 mm shank diameter and 249 mm total length for correct holder and clearance choice. Is this drill suitable for deep holes? Its 152 mm cutting length and 249 mm overall length make it appropriate for medium to deeper holes where an indexable insert solution is preferred. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of precise geometry and flexible insert compatibility — the result is consistent holemaking and reduced downtime. Order the drill directly via Metav Werkzeuge or request tailored advice from their consultants. Teknik Makina U738TM Indexable Drill — Ø38 mm, 152 mm cutting length The U738TM is an indexable drill designed for stable, high-efficiency holemaking in industrial machining, compatible with SPMG 1104 inserts. Ø38 mm drilling diameter 152 mm cutting length for deep holes 32 mm shank for secure clamping Compatible with SPMG 1104 inserts Consistent hole quality from engineered cutting geometry The U738TM delivers consistent bore tolerances thanks to its engineered cutting geometry and long cutting reach. With a Ø38 mm nominal diameter and a 152 mm cutting length, the tool is tailored for operations that demand repeatable results across longer depths. The indexable design reduces variability between cycles: worn cutting edges are replaced quickly, restoring original geometry without regrinding. This lowers scrap rates and increases first-pass yield, helping production processes stay predictable and efficient. The solid construction of the tool body maintains rigidity over its 249 mm overall length, which stabilises chip formation and supports uniform surface finish. Fast tool changes and straightforward setup reduce machine downtime A robust 32 mm shank combined with a 58 mm shank length ensures secure clamping in standard holders, enabling rapid changeovers and accurate axial alignment. The insert seat is configured for the SPMG 1104 grade, which is widely available from major manufacturers; the drill is expressly compatible with inserts from Taegutec and YG-1, offering sourcing flexibility and straightforward inventory management. Quick insert replacement translates into shorter maintenance windows and higher machine uptime. The modest mass of 1.32 kg balances handling convenience with the inertial stability required for steady cutting, supporting reliable cycle times on medium- to heavy-duty machining centres. Practical productivity: explained benefits and safe handling Indexable drilling with this tool means reduced per-hole cost and simplified tool logistics: indexable inserts remove the need for regrinding, while the drill body provides the repeatable datum for each new edge. The tool’s dimensions — notably the Ø38 mm drill diameter, 152 mm cutting reach and 249 mm overall length — allow clear planning of fixturing and coolant paths. For workshops less familiar with insert codes, SPMG 1104 denotes a common square format with a positive, multi-edge geometry suited to general-purpose holemaking; the matched seat ensures correct rake and clearance when new inserts are fitted. Metav’s product selection and technical documentation support specification decisions and help integrate the tool into existing tool lists. For reliable, high-output drilling with the Teknik Makina U738TM, contact Metav Werkzeuge in Emmerich for tailored technical advice by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: U738TM Manufacturer: Teknik Makina Product name: Indexable drill Facts Diameter: 38 mm Cutting length: 152 mm Overall length: 249 mm Shank diameter: 32 mm Shank length: 58 mm Weight: 1.32 kg eCl@ss: 21180201 Special features For indexable inserts: SPMG 1104 Compatible with insert brands: Taegutec, YG-1 SKU: U738TM FAQ What is the nominal drilling diameter of this tool? The nominal drilling diameter is 38 mm for the Teknik Makina U738TM indexable drill. Which insert type does the drill use? This drill accepts SPMG 1104 inserts and is designed to seat them correctly for repeatable cutting geometry. Which insert manufacturers are compatible? Insert brands tested for compatibility include Taegutec and YG-1 for the U738TM. What shank size is required for clamping? The tool is supplied with a 32 mm shank and a 58 mm shank length to fit standard holders. Is the U738TM suitable for deep-hole applications? With a 152 mm cutting length and a 249 mm overall length, the U738TM is intended for deeper holemaking while maintaining rigidity. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust combination of long cutting reach and secure clamping: the tool’s 38 mm diameter and 190 mm cutting length reduce the need for multiple tool changes while compatibility with Korloy WCM‑06T3 inserts keeps downtime to a minimum; order the indexable drill directly via Metav Werkzeuge or ask the consultants for tailored advice. Indexable drill body U798TM — 38 mm diameter, 32 mm shank by Teknik Makina The Indexable drill body U798TM is a production-grade drilling solution designed for use with WCM‑06T3 indexable inserts, offering extended cutting reach and secure shank clamping for machining operations. 38 mm diameter for deep hole drilling 190 mm cutting length for extended reach 32 mm shank for secure clamping Compatible with Korloy WCM-06T3 inserts Built for consistent production performance The U798TM is conceived as an indexable insert drilling solution that prioritises cycle-time efficiency and repeatable hole quality. The use of standard WCM‑06T3 inserts by Korloy allows fast insert changes and predictable cutting behaviour, which contributes to reduced non-productive time in a production environment. The tool body supports a modular workflow: by keeping the cutting geometry separate from the holder, maintenance is simplified and tool inventory can be optimised for varying batch sizes. The emphasis on insert compatibility ensures consistent cutting edges and simplified reconditioning compared with monolithic drills. Extended reach with dependable clamping Longer engagement is delivered through a 190 mm cutting length within an overall length of 287 mm, enabling access to deeper holes without compromising stability. A 32 mm shank and a dedicated 58 mm holder length provide a reliable clamping interface that reduces vibration and runout during operation. These characteristics translate into improved hole straightness and surface finish for repetitive machining tasks. The tool’s mass—1.48 kg—is balanced to support steady cutting dynamics while fitting standard toolholders that accept a 32 mm dia. shank. Efficient maintenance and straightforward integration Serviceability is a key benefit: insert replacement is rapid, lowering the mean time to repair and keeping assembly lines moving. The tool body is supplied ready for Korloy WCM‑06T3 inserts, streamlining procurement and reducing setup complexity. Clear, standardised mounting dimensions simplify integration into existing tool inventories and machine setups. For operations aiming to enhance uptime and rationalise tooling logistics, this drill body presents a practical route to increased throughput without extensive process changes. For ordering guidance or to discuss how the Teknik Makina indexable drill body U798TM fits into specific machining cells, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 for expert assistance Technical data Article number: U798TM Manufacturer: Teknik Makina Designation: Indexable drill body Dimensions & weight Diameter: 38 mm Cutting length: 190 mm Shank diameter: 32 mm Shank length: 58 mm Overall length: 287 mm Weight: 1.48 kg Compatibility & features Compatible inserts: WCM-06T3 Compatible insert maker: Korloy Application: indexable insert drilling FAQ Which inserts fit this tool? The tool is supplied for use with WCM‑06T3 indexable inserts; the U798TM holder accepts this insert type as specified. What are the key dimensions for toolholder selection? Reference the 32 mm shank and 58 mm holder length for clamping compatibility when integrating the U798TM into existing toolholders. Is the tool suitable for deep-hole drilling? With a 190 mm cutting length and 287 mm overall length, the indexable drill body is intended for extended-reach holemaking in production settings. How quickly can inserts be replaced? Insert change is rapid by design—WCM‑06T3 inserts are indexable and replaceable, enabling short maintenance intervals and reduced downtime. Which manufacturer produces this tool? The drill body is manufactured by Teknik Makina and supplied under article number U798TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable combination of a robust 38 mm diameter, 76 mm cutting length and a 32 mm shank delivers stable deep-hole performance and repeatable results; order the Solid drill U140TM directly via Metav Werkzeuge or ask our consultants if needed Solid drill U140TM — integral drill, 38 mm Ø with 32 mm shank (Teknik Makina) A Solid drill U140TM engineered for demanding deep-hole operations in production and maintenance workshops, offering a long cutting length and secure clamping for consistent machining Solid integral drill, 38 mm diameter 76 mm cutting length for deep holes 32 mm shank for secure toolholding Compatible with Korloy WCM-06T3 inserts Consistent cutting power for serial production The integral design provides a rigid tool body that reduces vibration and improves hole roundness in repeated cycles. With a 38 mm diameter and 76 mm cutting length, this tool keeps tool deflection low while enabling deeper holes without multiple setups. The result is improved process reliability and less rework — an important rational advantage for production planners seeking stable cycle times and predictable tool life. The description emphasises measurable performance rather than marketing claims. Secure mounting for repeatable accuracy A substantial 32 mm shank with a 58 mm effective clamp section ensures reliable seating in standard holders and minimises micro-movement under load. The longer shank engagement supports stable torque transmission and helps maintain concentricity over the full 173 mm overall length. At a weight of 0.975 kg, the tool balances robustness with manageable handling during tool changes, supporting quick set-ups in automated or manual machines. Standardised insert system for straightforward logistics Designed to accept Korloy indexable inserts (type WCM-06T3), the drill simplifies inventory and reduces the need for bespoke tool suppliers. The compatibility with a widely used insert format allows predictable procurement and easier regrinding or replacement. The 76 mm cutting length and insert geometry combine to support controlled chip formation and evacuation, which helps to maintain cutting temperatures and prolong insert life in series operations. Ideal for workshop integration and process security This integral drill suits production environments where repeatability and uptime matter. The combination of a rigid body, standard insert compatibility and secure shank engagement reduces unexpected downtime and supports efficient tool management. Beyond technical performance, the tool fits a pragmatic purchasing strategy: it uses established interfaces and measurable dimensions to simplify specification, stock control and machine setup. Consult Metav Werkzeuge for suitability and delivery of Teknik Cutting Tools' Solid drill U140TM — our specialists in Emmerich provide technical advice and reliable supply for industrial workshops Technical data Article number: U140TM Manufacturer: Teknik Makina Facts Diameter: 38 mm Cutting length: 76 mm Overall length: 173 mm Shank diameter: 32 mm Shank length: 58 mm Weight: 0.975 kg Special features Compatible with Korloy WCM-06T3 inserts Passend für inserts manufacturer: Korloy Integral (solid) drill design Suitable for deep-hole machining FAQ What materials is this drill suitable for? The Solid drill U140TM is specified for general deep-hole operations; material suitability depends on insert grade and machining parameters rather than the drill body alone Which insert type does the tool use? The tool accepts WCM-06T3 indexable inserts from Korloy, facilitating straightforward replacement and stock management What are the critical dimensions to check before ordering? Check the 38 mm diameter, 76 mm cutting length, 32 mm shank diameter and 173 mm overall length against machine holder capacity and hole specifications Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a stable 32 mm shank and 3 mm cutting width for reliable grooving and parting operations; its compatibility with Korloy 3C MGM inserts ensures fast tool changes and predictable results — order directly via Metav Werkzeuge or consult our advisors for application guidance. Grooving Clamp Holder K608TM – 32 mm shank, 250 mm overall length (Teknik Makina) A robust Grooving Clamp Holder K608TM engineered for secure clamping of indexable 3C MGM inserts in turning and grooving applications across general workshop and light industrial machine tools 32 mm shank diameter for stable mounting 3 mm maximum cutting width Compatible with Korloy 3C MGM inserts 250 mm overall length for extended reach Stable clamping for consistent grooves and parting The holder’s 32 mm shank is designed to deliver a rigid connection between toolpost and cutting edge, reducing vibration and helping to maintain cutting geometry. This rigidity is particularly beneficial when working with narrow cuts: the 3 mm cutting width provides a defined groove with minimal deflection, which results in repeatable part dimensions and less scrap. For workshops seeking predictable finishing tolerances, the combination of a solid shank and precise clamping equals fewer reworks and faster cycle stability. Reach and clearance that improve process flexibility With a 250 mm overall length and a body diameter of 38 mm, the tool holder offers added reach for deeper setups and complex part geometries while maintaining a compact footprint near the toolpost. Increased reach reduces the need for multiple setups or long overhangs from adaptors, shortening preparation time and improving throughput. The moderate mass of 1.555 kg contributes to steadiness without excessive inertia, supporting efficient handling during tool changes and set-up work. Easy integration with common insert systems and bars Compatibility with Korloy 3C MGM inserts and the ISO bar designation S32S 3C-R makes the holder straightforward to integrate into existing turning tool inventories. Workshops using MGM clamp systems can swap inserts quickly without adapting fixtures, enabling minimal downtime when changing operations. For purchasers, this means predictable tooling logistics and simpler inventory management because the holder works with established insert geometries and clamping principles. Built for workshop reliability and clear benefits The clamping concept and the specified cutting height of 60 mm provide a secure mount for indexable inserts, supporting controlled chip formation and consistent cutting depth. This reliability contributes to cost-effective production by reducing tool-change frequency and minimising machining deviations. Where precision and repeatability matter, a purposeful holder construction supports both productivity and operator confidence, ensuring that each groove or parting cut meets expected tolerances. For dependable grooving performance from Teknik Makina, contact Metav Werkzeuge for tailored application advice and fast supply from our Emmerich site Technical data Article number: K608TM Manufacturer: Teknik Makina Designation: Grooving clamp holder (Stechklemmhalter) Compatible inserts: 3C MGM Suitable for insert maker: Korloy Boring bar designation ISO: S32S 3C-R Clamp holder bar type: MGM Facts Shank diameter: 32 mm Cutting height: 60 mm Cutting width: 3 mm Overall length: 250 mm Body diameter: 38 mm Weight: 1.555 kg Special features Secure clamp for indexable inserts Designed for grooving and parting operations Fits standard S32S 3C-R bar systems Compatible with Korloy 3C MGM insert family FAQ Which inserts are compatible with this holder? The holder accepts Korloy 3C MGM indexable inserts; the clamping system is designed for the 3C MGM geometry used in grooving applications. What shank size is required for mounting? A 32 mm shank interface is specified for this grooving clamp holder, matching standard toolpost adaptors and boring bar mounts. Is the holder suitable for deep grooving or long overhangs? The 250 mm overall length gives extended reach for deeper setups, while the 32 mm shank helps maintain rigidity during longer overhangs. Which bar designation does this holder match? The tool is intended for use with bars to ISO designation S32S 3C-R and the MGM clamp type. Can the holder be used for both parting and precision grooves? Yes, the clamping stability and 3 mm cutting width make it suitable for defined parting cuts and narrow precision grooves. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of rigid clamping, precise grooving dimensions and straightforward insert compatibility to maintain stable turning operations and predictable cycle times; order directly via Metav Werkzeuge or contact our consultants for application advice and supply from Emmerich. Grooving clamping holder — Teknik Makina, rigid shank Ø32 mm, 4 mm cutting width Grooving clamping holder designed for narrow-groove and parting applications on lathes, compatible with Korloy 4C MGM inserts and engineered for repeatable positioning in production environments Robust clamping design for secure insert retention Shank Ø32 mm for rigid setup and minimal vibration Cutting width 4 mm for precise narrow grooves Compatible with Korloy 4C MGM inserts Improved process stability through rigid design The holder delivers a consistent, vibration‑resistant mounting that supports stable cutting conditions during grooving and parting operations. A solid tool body reduces chatter and extends insert life by keeping the insert geometry aligned under load. The holder’s geometry has been optimised for repeatable positioning, which helps maintain tolerances across batch production. For operations where predictable tool behaviour and minimised rework are decisive, this holder provides measurable process advantages. Clear compatibility and simple interface with inserts Compatibility with Korloy style inserts is provided via the proven clamping arrangement, accepting the 4C MGM insert form. The holder is referenced to the ISO designation S32S 4C‑R, making spindle and turret planning straightforward when integrating into existing tool inventory. The clamping system permits secure seating of the insert, which simplifies index changes and reduces set‑up time for maintenance tasks. This compatibility supports inventory standardisation and more efficient tool management. Compact dimensions that favour rigidity and access Key dimensions ensure both rigidity and accessibility at the cut: a shank Ø32 mm gives a robust connection to the turret or toolpost, the overall length 250 mm preserves reach while limiting overhang, and a cutting height 60 mm aligns the insert at nominal centre positions for many turning setups. The cutting width 4 mm is configured for narrow grooves and parting operations where space and precision are critical. The component mass of 1.552 kg provides damping without excessive inertia, aiding stable plunge and groove passes. Practical benefits for workshop and production use Designed for integration into production tooling racks, the holder enables faster changeovers and consistent machining results. The straightforward mechanical interface reduces the potential for assembly errors, while the compatibility with widely used insert formats lowers stocking complexity. For workshops seeking to streamline grooving operations, the holder contributes to consistent cycle times and simplified tool maintenance routines, supporting overall shopfloor productivity. Speak with Metav Werkzeuge for tailored selection and supply of Teknik Makina grooving solutions — contact info@metav-werkzeuge.com or call +49 2822 7131930 for specific application advice and availability from Emmerich. Technical data Article number: K614TM Manufacturer: Teknik Cutting Tools / Teknik Makina Brand: Teknik Makina Facts Shank diameter: 32 mm Overall length: 250 mm Diameter: 38 mm Weight: 1.552 kg Special features Insert compatibility: 4C MGM Compatible insert manufacturer: Korloy ISO designation: S32S 4C‑R Cutting height: 60 mm Cutting width for grooving: 4 mm FAQ What insert types fit this grooving clamping holder? The holder accepts 4C MGM style inserts and is specified for Korloy 4C MGM formats; the interface is aligned to the ISO reference S32S 4C‑R for straightforward match‑up. Is the shank size suitable for heavy‑duty turning turrets? With a shank Ø32 mm, the holder provides a rigid connection that is commonly used in robust turret setups, offering reduced overhang and improved stability for grooving tasks. Can the holder be used for parting as well as grooving? The design of the grooving clamping holder supports both narrow‑groove machining and controlled parting operations where the 4 mm cutting width and secure clamp are appropriate. How does the overall length affect tool performance? The overall length 250 mm balances reach and stiffness, limiting overhang to improve damping and reduce the risk of chatter compared with longer holders. Which SKU and brand should be referenced when ordering or restocking? Reference K614TM from Teknik Makina when ordering the grooving clamping holder to ensure the correct shank, length and insert compatibility are supplied. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining compatibility with multiple insert sizes, a robust 38 mm cutting diameter and a 32 mm shank, this tool delivers reliable thread production and extended service intervals for mixed-production environments; order directly via Metav Werkzeuge or consult their specialists for application support. DC212TM thread milling cutter by Teknik Makina — compatible with S21, S30 and S40 indexable inserts; 38 mm diameter DC212TM thread milling cutter for precision thread milling in production workshops and CNC centres using S21, S30 and S40 indexable inserts Compatible with S21, S30 and S40 inserts 38 mm cutting diameter for robust threads 150 mm overall length for deep reach 32 mm shank diameter, Torx M5x12 clamping Consistent, high-performance threading for mixed production The DC212TM is engineered for productive thread generation where flexibility and repeatability matter. Its compatibility with S21, S30 and S40 indexable inserts allows a single tool body to be equipped for different thread requirements, reducing tool changeovers and stocking complexity. The 38 mm cutting diameter is designed for robust thread profiles, while the use of indexable inserts ensures economical regrinding cycles and fast on-machine repairs. For managers aiming to increase throughput without sacrificing quality, the tool’s configuration enables predictable cycle times and simplified tool management. Secure clamping and rigid mounting for repeatable results Stable insert fixation is achieved via a Torx M5 x 12 clamping screw, operated with a T20 key, which provides a reproducible clamping force and minimises micro-movements during machining. The 32 mm shank diameter ensures high rigidity when mounted in standard toolholders, reducing chatter and improving surface finish of the threaded profile. These mechanical characteristics translate directly into fewer rejects and less rework — a rational efficiency improvement for shops where tolerances and repeatability are critical. Workflow advantages that reduce downtime and inventory With a 150 mm overall length, the cutter reaches deeper thread positions while maintaining balance between accessibility and stiffness. Adopting a tool that accepts several insert sizes reduces the number of dedicated cutters required across different jobs, simplifying procurement and storage. Metav Werkzeuge’s supply network complements this by offering dependable availability and expert advice, allowing maintenance planners and production engineers to secure replacement inserts and components quickly. The result is a measurable reduction in production interruptions and a smoother tool lifecycle. For application guidance or to source the Teknik Cutting Tools DC212TM thread milling cutter, contact Metav Werkzeuge for tailored advice and fast supply: call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: DC212TM Manufacturer: Teknik Makina Designation: Thread milling cutter for S21, S30 and S40 indexable inserts ECLASS: 21180805 ETIM: EC011860 Core technical data Cutting diameter: 38 mm Overall length: 150 mm Shank diameter: 32 mm Clamping screw: M5 x 12 (Torx T20) Design and special features Compatible with S21, S30 and S40 indexable inserts Indexable-insert system for economical maintenance Torx clamping for secure insert fixation Suitable for CNC and production workshop use FAQ What insert types are compatible with this cutter? The cutter accepts S21, S30 and S40 indexable inserts; the body is configured to take these standard insert sizes for flexible thread machining. Which screw and key are required for insert clamping? Insert clamping is via an M5 x 12 Torx screw tightened with a T20 key, providing secure and repeatable fixation for the inserts. What are the main dimensions of the tool? Key dimensions are a 38 mm cutting diameter, 150 mm overall length, and a 32 mm shank diameter as specified for the DC212TM thread milling cutter. Is this tool suitable for deep internal threads? The 150 mm overall length offers extended reach for deeper thread positions while balancing rigidity to maintain thread quality. Can this tool be used across mixed production with varying thread demands? Yes — the compatibility with multiple standard insert sizes allows rapid adaptation to different thread profiles and reduces the need for multiple dedicated cutters. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Robust clamping and proven insert compatibility deliver repeatable grooves and secure parting operations; the combination of a rigid shank and precise insert seating supports stable cutting and reduced rework. Order the part via Metav Werkzeuge or consult their specialists for application-specific advice. Grooving clamp holder K728TM — 4C insert holder with 32 mm shank by Teknik Makina A grooving clamp holder engineered for narrow-groove and parting operations that accepts Sandvik 4C indexable inserts and fits an S32S shank standard Rigid 32 mm shank for stable mounting Compatible with Sandvik 4C indexable inserts 4 mm cutting width for narrow grooving 60 mm cutting height for deep cuts 250 mm overall length for extended reach Stable interface for repeatable turning and parting The combination of a 32 mm shank and a solid clamp design produces a stable mounting that limits vibration and improves surface finish. In practical terms, a stiffer holder reduces tool chatter and contributes directly to longer insert life and fewer rejected parts. The holder’s mass is balanced for lathe use; its measured weight supports predictable dynamics at common spindle speeds. Specified mounting dimensions allow straightforward integration into existing tool posts, enabling reliable, repeatable set-ups and shorter machine idle time. Consistent groove geometry with indexable insert support Designed around the Sandvik 4C insert form, the holder provides a secure seat for indexable cutting edges so that single-seat tightening delivers consistent radial and axial positioning. The 4 mm cutting width combined with a 60 mm cutting height supports both narrow grooving and moderate-depth parting, giving a predictable chip control strategy when paired with suitable insert grades. The indexable system simplifies changing edges: worn corners are rotated or replaced without refacing the holder, reducing maintenance time and supporting continuous production. Workshop-ready reach, designation and handling With a 250 mm overall length and an S32S ISO shank designation, the holder offers extended reach for overhang applications while maintaining a known interface to standard lathe toolposts. The unit’s design facilitates quick clamping of the insert and reliable torque transmission from clamp screw to insert seat. Identified in the range as K728TM, this grooving clamp holder is suitable where secure insert retention and predictable cutting geometry are priorities. For additional technical clarification, Metav’s consultants can provide machining parameter guidance and check compatibility with existing fixtures. Contact Metav Werkzeuge for tailored application advice and to arrange supply of the Teknik Makina K728TM grooving clamp holder directly from Emmerich Technical Data SKU: K728TM Manufacturer: Teknik Makina Facts Shank diameter: 32 mm Overall length: 250 mm Cutting height: 60 mm Cutting width: 4 mm Diameter: 39 mm Weight: 2.854 kg Special features Compatible inserts: 4C Compatible insert manufacturer: Sandvik Shank designation: S32S Secondary designation: 4C-R-123 SDV FAQ What insert type fits this holder? The holder accepts 4C indexable inserts and is specified for use with Sandvik 4C insert geometries, ensuring correct seating and repeatability for the K728TM grooving clamp holder. Which shank does the tool require for mounting? Mounting requires a 32 mm shank interface; the product is manufactured to the S32S shank designation for standard lathe toolpost compatibility. What groove widths and depths is the holder designed for? The design supports a 4 mm cutting width and a 60 mm cutting height, suitable for narrow grooving and moderate-depth parting tasks when paired with appropriate insert grades. Is the K728TM suitable for extended reach applications? Yes, the 250 mm overall length provides additional reach for overhang requirements while maintaining secure insert clamping for stable machining. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust indexable design with a Ø39 mm cutting diameter and 36 mm cutting height for reliable chamfering and minimal downtime; order the chamfer cutter directly via Metav Werkzeuge or consult our technical advisors for application support. Chamfer cutter S343TM — indexable-insert cutter, Ø39 mm, Teknik Makina The Chamfer cutter S343TM is an indexable-insert milling tool engineered for precise chamfering and bevel preparation in metalworking applications. Indexable system for TCMT 16T3 inserts Ø 39 mm diameter for medium chamfers 36 mm cutting height for deep chamfers 20 mm shank for stable clamping Faster chamfering with replaceable inserts The indexable concept offers a clear production advantage: rapid insert changes lead to reduced downtime and lower per-part costs compared with solid-tool replacements. Fitted for TCMT 16T3 inserts, the cutter accepts commonly available carbide inserts, enabling a quick insert change routine that is compatible with standard workshop stocking practices. This design supports steady throughput in repetitive chamfering tasks and helps maintain predictable edge quality across batches. Stable clamping for consistent edge quality A robust tooling foundation improves process reliability. The combination of a 20 mm shank and a tool Ø39 mm body keeps the cutter rigid in the holder, which reduces vibration and preserves surface finish. With a 36 mm cutting height and two cutting edges, the geometry provides steady material engagement for chamfers and bevels; the included 30° and 60° chamfer options allow selection of the best edge angle for a given part design. Consistent clamping and predictable chip formation translate into fewer reworks and a more controlled machining process. Practical workshop handling and maintenance Maintenance is straightforward: inserts are secured with an M3.5x8.5 Torx screw and serviced using a T15 key, simplifying routine changeover and reducing toolroom time. The tool’s 100 mm total length and compact mass (approx. 0.356 kg) make it easy to handle during toolprep and mounting, while the indexable concept lowers overall tooling inventory by allowing one cutter body to serve multiple insert life cycles. For production environments that value both uptime and cost-efficiency, this cutter forms a pragmatic part of a modular tooling strategy. Secure Teknik Cutting Tools' chamfer cutter S343TM through Metav Werkzeuge for dependable stock and application advice — contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for specification assistance and order coordination Technical data Article number: S343TM Manufacturer: Teknik Makina SKU: S343TM Facts Diameter: 39 mm Shank diameter: 20 mm Cutting height: 36 mm Total length: 100 mm Cutting edges: 2 Weight: 0.356 kg Special features For indexable inserts TCMT 16T3 Chamfer angles: 30° and 60° Torx screw: M3.5x8.5 Torx key size: T15 FAQ What inserts are compatible with this cutter? The cutter is designed for TCMT 16T3 indexable inserts; TCMT 16T3 inserts fit the S343TM cutter and are commonly available from insert suppliers. How are inserts secured and changed? Inserts on the S343TM are fastened with an M3.5x8.5 Torx screw and require a T15 Torx key for secure and repeatable replacement. Which chamfer angles does the tool provide? The cutter features geometries for 30° and 60° chamfers, enabling straightforward selection of the desired edge profile for bevel preparation. Is the shank suitable for standard tool holders? The 20 mm shank and 100 mm overall length are compatible with holders accepting 20 mm shanks; the rigid shank supports stable clamping and consistent machining results. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a robust 32 mm shank and compatibility with 16–22ER indexable inserts for stable, precise internal turning; order the tool directly via Metav Werkzeuge or consult the specialists for application advice. SIL S32T boring bar — 32 mm shank, for 16–22ER indexable inserts (Teknik Makina) The SIL S32T boring bar is a left-hand internal turning tool designed for reliable workshop machining with 16–22ER indexable inserts, ideal for precision internal profiles and finishing operations For 16–22ER indexable inserts Left-hand cutting direction 32 mm shank diameter 300 mm overall length Improved rigidity for more accurate internal turning The substantial 32 mm shank provides increased rigidity, reducing vibration during machining and supporting a more consistent surface finish on internal bores. As a result, the tool delivers more stable cutting conditions and fewer rework cycles, which supports higher first-pass quality in routine turning tasks. The combination of a solid ISO-design shank and engineered geometry helps maintain concentricity when working at extended reach. Faster setup and predictable tool changes with standard inserts Compatibility with 16–22ER indexable inserts simplifies inventory management and shortens changeover times. The tool accepts standard ER-style inserts and is specified for use with an ER22 clamping arrangement, enabling reproducible seating and secure fixation of the cutting grade. This configuration reduces setup time and allows consistent chip control and cutting performance with commonly available insert grades. Workshop-oriented design for safe clamping and accessibility With an overall length of 300 mm and a cutting height of 40 mm, the bar balances reach and stiffness for internal operations. The left-hand cutting direction is specified for particular turning orientations and must be matched with machine tool rotation and application demands. The robust mass (approx. 1.827 kg) supports steady machining and predictable tool behaviour, while the ISO designation and familiar design facilitate integration into existing toolholder systems. For precise internal turning needs, request compatibility advice or place an order for the Teknik Cutting Tools SIL S32T through Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for tailored guidance and delivery information Technical Data Article number: K335TM Manufacturer: Teknik Makina Model / designation: SIL for 16-22ER Indexable Inserts ISO designation: SIL S32T Cutting direction: left Shank type: ER22 compatible SKU: K335TM Core specifications Shank diameter: 32 mm Overall length: 300 mm Cutting height: 40 mm Weight: 1.827 kg Diameter: 39 mm Features For 16–22ER indexable inserts Left-hand cutting direction Compatible with ER22 clamping holder ISO design SIL S32T Brand: Teknik Makina FAQ What insert sizes are compatible with this boring bar? The SIL S32T boring bar is designed for 16–22ER indexable inserts, allowing the use of common ER-format insert sizes for internal turning. Which cutting direction does the tool use? The tool is specified with a left-hand cutting direction, which must be matched to the machine’s rotation and the intended machining strategy. What shank and overall length does the bar offer? The bar features a 32 mm shank diameter and a 300 mm overall length, providing a balance of reach and rigidity for internal operations. Which clamping holder is recommended for this bar? The product is supplied for use with an ER22 clamping arrangement to ensure secure, repeatable fixation of the insert and holder assembly. What is the ISO designation and SKU for ordering? ISO designation SIL S32T; SKU K335TM for reference when ordering or checking compatibility. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust combination of a 39 mm nominal diameter and a 117 mm cutting length for consistent hole quality and extended tool life; the 32 mm shank ensures stable clamping and reduced runout. Order the indexable drill directly via Metav Werkzeuge or ask our consultants if needed. Indexable drill (U183TM) — Teknik Makina, 39 mm, 32 mm shank The indexable drill by Teknik Makina is designed for efficient holemaking in production and workshop environments, offering deep cutting capacity and compatibility with Korloy WCM-06T3 indexable inserts. 39 mm nominal diameter for robust holes 117 mm cutting length for deep penetration 32 mm shank for stable toolholding Compatible with Korloy WCM-06T3 inserts Productivity through optimised cutting geometry and depth The tool body combines a substantial 39 mm diameter with a 117 mm cutting length to deliver stable material removal rates and consistent hole dimensions across longer cycles. The extended cutting length reduces the need for multiple passes in common drilling operations, which shortens cycle times and improves workshop throughput. The design focuses on chip control and thermal stability, so the operator benefits from reliable performance during continuous production runs while maintaining hole integrity and repeatability. Stable clamping for improved runout and surface finish Equipped with a 32 mm shank, the tool provides a secure interface with standard holders and collets suited to that dimension. This larger shank diameter increases torsional rigidity and helps minimise runout, which directly affects hole roundness and surface finish. At a weight of 1.244 kg, the assembly offers mass that aids vibration damping without compromising tool change speed. For teams upgrading fixturing or checking holder compatibility, these dimensions simplify the selection of appropriate toolholding systems and reduce set-up time. Fast insert changes and straightforward tool maintenance This drill accepts WCM- 06T3 indexable inserts from Korloy, allowing quick replacement of cutting edges when wear occurs. The indexable system reduces downtime compared with regrinding solid cutters and lowers per-hole tooling cost over the tool life. Insert-based geometry also enables selective specification of grade and chipbreaker variants for particular materials or finishes, so production planners can balance cutting speed, tool life and surface result without replacing the full tool body. Engineered for production workshops and CNC cells As a robust drill body from Teknik Cutting Tools, the unit is aimed at machining centres, dedicated drilling stations and general workshop applications where productivity and predictable tool behaviour are priorities. The combination of precision, stability and modular insert technology supports batch production as well as one-off engineering tasks. Supplied via Metav Werkzeuge, the product is backed by a European logistics and quality filter that helps smaller workshops access high-performance tooling with dependable delivery and technical guidance. For tailored recommendations on toolholders, insert grades or to request a quotation for the Teknik Makina indexable drill U183TM, contact Metav Werkzeuge in Emmerich — advisors are available to match the drill to existing machines and production goals (info@metav-werkzeuge.com • +49 2822 7131930) Technical Data Article number: U183TM Manufacturer: Teknik Makina Designation: Vollbohrer eClass: 21180201 Facts Diameter: 39 mm Overall length: 214 mm Cutting length: 117 mm Shank diameter (aufnahme): 32 mm Shank length: 58 mm Weight: 1.244 kg Special features Compatible insert type: WCM- 06T3 Compatible insert manufacturer: Korloy Story trigger: vollbohrer FAQ What inserts are compatible with this drill? The Teknik Makina indexable drill U183TM is compatible with Korloy WCM- 06T3 inserts, enabling rapid edge changes. What are the primary dimensions to consider for setup? Key dimensions for the U183TM are 39 mm diameter, 214 mm overall length and 117 mm cutting length; shank diameter is 32 mm. Which shank size is required for holders? A 32 mm shank dictates the holder or collet bore size; toolholding systems that accept a 32 mm diameter will suit the U183TM. Is the cutting length sufficient for deeper bore work? The 117 mm cutting length provides capacity for deeper holes than standard short drills and supports single-pass operations in many production scenarios. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid tool body with a Ø 39 mm cutting diameter, 156 mm effective cutting length and compatibility with SPMG 1104 indexable inserts for reliable deep-hole machining — order or request advice via Metav Werkzeuge for seamless integration into production. Insert Drill U739TM – Indexable drill body, Ø 39 mm, 156 mm cutting length (Teknik Makina) A robust Insert Drill U739TM engineered for indexable SPMG 1104 inserts, intended for precision through-hole and deep-hole operations in CNC machining centres Solid indexable body for SPMG 1104 inserts Ø 39 mm cutting diameter for through drilling 156 mm effective cutting length for deep holes 32 mm shank for secure toolholder mounting High-performance drilling through long cuts and reliable insert compatibility The indexable drill body provides a combination of deep cutting capacity and proven insert compatibility that reduces downtime. With an effective cutting length of 156 mm and a cutting diameter of Ø 39 mm, the tool is designed to maintain concentricity over long reaches, which improves hole quality and reduces secondary operations. Compatibility with SPMG 1104 inserts plus recognised insert suppliers such as Taegutec and YG-1 ensures predictable cutting data and ready availability of replacements, translating into measurable productivity gains on batch and continuous runs. Stable clamping and repeatable accuracy for consistent production A 32 mm shank and a total length of 253 mm create a robust connection to the machine spindle, increasing torsional stiffness and reducing vibration during drilling cycles. The 58 mm shank engagement length supports secure mounting and repeatable positioning, which is especially valuable for automated setups and palletised machining. At approximately 1.356 kg, the tool body balances mass and rigidity to deliver stable cutting conditions without excessive tool overhang, helping maintain tolerance and surface finish across series production. Cost-effective machining strategy with indexable inserts By using replaceable indexable inserts, the drill body minimises tooling costs and simplifies maintenance: worn cutting edges are replaced quickly without regrinding the body, reducing machine downtime. The compatibility with established insert grades means optimised tool life for common workpiece materials and easier sourcing from Taegutec and YG-1. For operations seeking scalable, predictable performance in CNC environments, the design supports a low total cost of ownership and easier inventory management across multiple toolholders. Contact Metav Werkzeuge today for tailored tooling advice and rapid supply from Emmerich — Metav’s specialists can confirm suitability for specific CNC setups and insert grades for the U739TM insert drill body Technical Data Article number: U739TM Designation: Vollbohrer Manufacturer: Teknik Makina Facts Diameter: 39 mm Cutting length: 156 mm Shank diameter: 32 mm Shank length: 58 mm Overall length: 253 mm Weight: 1.356 kg Special features Compatible inserts: SPMG 1104 Compatible insert manufacturers: Taegutec, YG-1 Classification: eClass 21180201 Files: 62de7ec233927e49dbf3276b, 62de7dd60f56dbb4de4dbedd FAQ What insert type does the tool accept? The U739TM insert drill body is built for SPMG 1104 indexable inserts, providing straightforward replacement and proven cutting edge geometry for holemaking. Which insert brands are compatible with this tool? Insert manufacturers listed as compatible include Taegutec and YG-1, making it easy to source matching grades and chipbreakers for varied materials. What are the key dimensions that affect rigidity and reach? Key measures are the Ø 39 mm cutting diameter, 156 mm cutting length and a 32 mm shank; together these determine stiffness, reach and suitability for deep-hole drilling. Is the tool suitable for automated CNC cells and palletised systems? Yes, the secure 32 mm shank connection and 58 mm engagement length offer the repeatability and stability required for automated setups. Can the insert drill body be used for long production runs? Designed for indexable inserts, the U739TM supports quick insert changes and predictable tool life, which helps maintain uptime and reduce tooling costs in series production. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a balance between robust rigidity, replaceable-index insert economy and straightforward servicing for stable production drilling. With a 39 mm diameter and a 32 mm shank the tool minimises vibration while the use of SPMG 1104 inserts keeps tooling costs predictable — order directly via Metav Werkzeuge or consult the technical team for application advice. Indexable drill U839TM – 39 mm diameter, 32 mm shank (Teknik Makina) The Indexable drill U839TM is a heavy-duty indexable drilling solution for industrial machining where fast insert changes and consistent hole quality are required High rigidity: 39 mm operating diameter Secure clamping: 32 mm shank for stability Compatible with SPMG 1104 indexable inserts 117 mm effective cutting length, 214 mm overall Enhanced stability for consistent hole quality The tool’s 39 mm diameter combined with a sturdy 32 mm shank delivers improved axial and radial stiffness under cutting loads, which means fewer deviations in hole geometry and reduced rework. Built with a compact overall length of 214 mm, the design keeps overhang to a minimum while still offering reach for many production tasks. The moderate mass of 1.155 kg contributes to damping of chatter without adding unnecessary inertia, so machining routines run smoothly and spindle load is predictable — a clear efficiency gain for production-focused setups. Fast, cost-efficient insert handling Designed for use with SPMG 1104 indexable inserts and compatible with Taegutec and YG-1 insert systems, the drilling head allows rapid replacement of cutting edges. Indexable inserts separate the cutting grade from the tool body, enabling economical maintenance: worn inserts are swapped instead of replacing the whole cutter. This approach reduces tool downtime and simplifies inventory management for workshops that prefer standardised insert formats from recognised manufacturers. Reach and cutting length tuned for deeper bores An effective cutting length of 117 mm provides the necessary engagement for deeper hole operations without excessive tool extension. That cutting length, paired with the overall 214 mm length, gives a balance between accessibility and rigidity — fewer tool changes are required for medium-depth bores, which supports continuous production cycles. The combination of cutting reach and secure shank interface is intended to support repeatable bore depths and consistent surface finishes in serial operations. Ready for production supply and technical guidance Supplied by Teknik Makina and available via Metav Werkzeuge, the tool is positioned for quick dispatch to professional workshops and industrial users. The indexable design supports predictable servicing routines and lower unit costs over time, while compatibility with established insert manufacturers simplifies procurement. For buyers seeking robust, maintainable drilling solutions, this indexable cutter integrates well into structured tool sets and controlled production workflows. For tailored application advice or to secure supply from Metav Werkzeuge in Emmerich, contact our specialists for precise delivery options and compatibility checks — Metav Werkzeuge provides reliable stock and technical support for Teknik Makina tools. Technical details SKU: U839TM Manufacturer: Teknik Makina Data Diameter: 39 mm Overall length: 214 mm Cutting length: 117 mm Shank diameter: 32 mm Shank length: 58 mm Weight: 1.155 kg Special features Indexable insert type: SPMG 1104 Compatible insert manufacturers: Taegutec, YG-1 Description note: Rapid dispatch; further tools available in catalogue FAQ Which insert type fits this indexable drill? The indexable drill U839TM is designed for SPMG 1104 inserts; inserts from Taegutec and YG-1 are suitable. What is the shank diameter and why does it matter? The tool has a 32 mm shank, providing a secure clamping interface that improves rigidity and reduces vibration during drilling. How deep can this tool drill effectively? The cutter offers an effective cutting length of 117 mm, which determines the practical maximum engagement for single-pass bore operations. Is the tool intended for production use? Yes — the combination of indexable inserts, a robust shank and balanced overall length makes it suitable for repeatable, production-oriented drilling tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid, indexable drilling solution that pairs diameter 39 mm stability with straightforward insert replacement for economical machining. The combination of robust shank support and compatibility with Korloy inserts ensures consistent hole quality and reduced tooling downtime. Order via Metav Werkzeuge or consult the technical team for application advice. Teknik Makina Vollbohrer – Indexable drill body, Ø 39 mm, Shank Ø 32 mm The Teknik Makina Vollbohrer is a high‑rigidity drill body designed for industrial metalworking applications where repeatable hole quality and quick insert turnover are required Indexable drill body design Diameter 39 mm for robust holes Shank Ø 32 mm, 58 mm engagement Compatible with Korloy WCM-06T3 inserts Steady performance for long production runs The drill body is engineered to deliver stable drilling performance through a combination of a generous diameter 39 mm cutting zone and a substantial shank Ø 32 mm that promotes secure clamping. With a cutting length of 156 mm, this tool is suited to demanding through‑hole and medium‑depth drilling tasks where rigidity and chip evacuation are decisive for surface finish and roundness. The design reduces vibration, which in turn increases repeatability and lowers scrap rates in batch production. Economical operation through replaceable inserts By accepting standard Korloy WCM-06T3 inserts, the tool body keeps running costs low and maintenance quick. The indexable concept allows worn cutting edges to be exchanged in minutes, restoring original geometry without replacing the carrier. This approach supports predictable tool‑life planning and reduces overall tooling expenditure compared with solid drills, while preserving cycle times and process stability on CNC machining centres. Designed for workshop integration and handling With an overall length of 253 mm and a shank engagement length of 58 mm, the carrier is dimensioned for common toolholders and heavy‑duty clamping systems, ensuring safe torque transmission and axial stability. The unit weight of 1.38 kg gives a tangible sense of robust construction without excessive mass that would complicate handling. The body accommodates familiar mounting and balancing procedures so that setup time is minimised and machine uptime is maximised. Enquire with Metav Werkzeuge for availability, customised configurations and batch supply — call +49 2822 7131930 or email info@metav-werkzeuge.com (Metav Werkzeuge, Emmerich) Technical data Article number: U639TM Manufacturer: Teknik Makina ECLASS: 21180201 Diameter: 39 mm Overall length: 253 mm Cutting length: 156 mm Shank diameter: 32 mm Shank length: 58 mm Weight: 1.38 kg Compatible inserts: WCM-06T3 Compatible insert manufacturer: Korloy Technical files: 62de7ec30f56dbb4de4dbf2d, 62de7dd9148ec6b71020ff6b FAQ What materials is this drill body suitable for? The drill body accepts Korloy WCM-06T3 indexable inserts and is suitable for a wide range of metals; material compatibility depends on the chosen insert grade and geometry. How are inserts fixed and replaced? Inserts for this drill body are clamped into the pockets designed for WCM-06T3 format; replacement restores cutting geometry quickly and reduces overall tooling costs for the U639TM drill body. Which machines can accommodate this tool? The carrier is intended for CNC drilling and milling centres with toolholders matching a 32 mm shank; the 58 mm engagement length supports heavy clamping and torque transfer. What are the benefits of the indexable system compared with solid drills? Indexable systems lower lifecycle costs through individual insert replacement, allow controlled wear management and often deliver reduced cycle times for medium‑to‑large production runs. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of extended cutting reach, secure clamping and proven insert compatibility for efficient, repeatable holemaking in series production; order via Metav Werkzeuge or consult the technical team for application advice. Indexable drill U799TM – 39 mm diameter, 195 mm cutting length (Teknik Cutting Tools) The Indexable drill U799TM is an indexable insert drill designed for medium‑to‑deep holemaking in production environments, combining long cutting reach with a robust 32 mm shank for secure clamping and stable machining. 39 mm diameter for deep-hole drilling 195 mm cutting length for long reach 32 mm shank for secure clamping Compatible with Korloy WCM-06T3 inserts Increased productivity through extended cutting reach and stable geometry The long cutting zone of 195 mm and an overall length of 292 mm allow the tool to reach into deeper bores while maintaining stability. This extended reach reduces the need for secondary operations or special tool changes, which translates into shorter cycle times and fewer machine setups. The robust geometry is engineered to minimise deflection; as a result, hole quality is preserved across longer passes and repeatability is improved for batch production. Reliable insert system for consistent hole quality and cost efficiency Compatibility with Korloy WCM-06T3 indexable inserts provides an economical approach to tool life management: worn cutting edges are replaced quickly without regrinding, keeping downtime to a minimum. The insert system supports controlled chip formation and repeatable cutting performance, which helps to reduce scrap rates and contributes to a favourable cost‑per‑hole calculation. The tool's indexable concept is particularly suitable where straight, repeatable bores are required in series work. Secure clamping and easy integration into existing toolholders The 32 mm shank diameter and a dedicated shank length of 58 mm permit confident clamping in standard collet or hydraulic toolholders; the substantial shank cross‑section supports torque transmission and vibration damping. The tool, weighing 1.52 kg, is balanced for stationary machining and can be integrated into typical milling and drilling spindles without special adaptors when the machine accepts the specified shank size. Quick mounting and predictable runout contribute to consistent surface finish and positional accuracy. Application guidance and workshop compatibility The indexable system is intended for use with Korloy inserts and can be matched to insert grades that suit a range of steels and alloys; insert selection determines the material spectrum and cutting parameters. The drill's dimensions—39 mm diameter and 195 mm cutting length—should be considered when planning fixture clearances and coolant supply. For workshops seeking to consolidate tooling, the tool's standard shank and insert pattern support rapid integration into established toolsets, reducing procurement complexity and spare‑part variants. Contact Metav Werkzeuge in Emmerich for technical consultation on application suitability, insert selection and delivery of the Teknik Cutting Tools indexable drill U799TM — eMail info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data SKU: U799TM Manufacturer: Teknik Makina Designation: Indexable drill Dimensions & weight Diameter: 39 mm Cutting length: 195 mm Overall length: 292 mm Shank diameter: 32 mm Shank length: 58 mm Weight: 1.52 kg Features & compatibility Compatible insert: WCM-06T3 Suitable insert manufacturer: Korloy Indexable insert system for quick edge replacement Designed for medium‑to‑deep holemaking FAQ Which insert type does this tool accept? The indexable drill U799TM accepts Korloy WCM-06T3 indexable inserts; insert seating and clamping conform to the specified insert geometry. What drilling depth is possible with the tool? The tool provides a 195 mm cutting length within an overall length of 292 mm, enabling medium‑to‑deep bore machining where that reach is required. What shank size and clamping are required? A 32 mm shank diameter and 58 mm shank length are specified for secure clamping in standard collet or hydraulic holders compatible with that dimension. Is the U799TM suitable for high‑volume production? The U799TM, with its indexable system and extended cutting length, is designed for repeatable, high‑volume applications where quick insert changes and stable machining reduce cycle time. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust indexable design and precise geometry to reduce cycle times and tool change frequency; the combination of a Ø 39 mm cutting diameter and 78 mm cutting length supports reliable medium‑depth holemaking. For ordering or compatibility questions, contact Metav Werkzeuge or consult the technical team. Indexable drill body U939TM — Ø 39 mm, 78 mm cutting length (Teknik Makina) The Indexable drill body U939TM is a 39 mm diameter tool body designed for indexable inserts and medium‑depth production drilling in precision machining environments Robust indexable design for high productivity Ø 39 mm cutting diameter for standard hole sizes 78 mm cutting length for medium‑deep holes 32 mm shank for secure clamping Higher throughput through indexable insert technology The body is engineered to accept SPMG 1104 inserts, enabling fast, repeatable edge changes and minimised downtime compared with solid drills. By combining a 32 mm shank with a balanced geometry and an overall length of 175 mm, the tool body offers stable cutting under cyclic loads; this reduces vibration and supports consistent hole quality across runs. The replaceable‑insert concept translates directly into a lower cost per hole and simplified tool inventory management. Quick adaptation and secure mounting for production Compatibility with leading insert suppliers (Taegutec, YG‑1) ensures ready availability of cutting grades and geometries suited to different operations. The 58 mm mounting length provides solid engagement in standard holders, while the body’s mass (1.007 kg) contributes to rigidity during plunge and peck drilling cycles. These attributes shorten setup time and help maintain spindle load stability during uninterrupted production, making the tool suitable for repeatable series work on CNC machines where predictable cycle times are essential. Built for shopfloor reliability and easy maintenance Constructed as a purpose‑built indexable drill body, the design emphasises serviceability: worn cutting edges are replaced in seconds, not hours, which supports sustained productivity and predictable maintenance intervals. The combination of a 39 mm diameter and 78 mm cutting length balances access to deeper features with chip evacuation requirements, delivering confident performance in component machining. Technical consultations are available to confirm holder compatibility or to select insert grades for specific tasks. Contact Metav Werkzeuge for tailored compatibility checks or to request delivery from Emmerich: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: U939TM Manufacturer: Teknik Cutting Tools (Teknik Makina) eClass: 21180201 Compatible inserts: SPMG 1104 Core specifications Cutting diameter: 39 mm Cutting length: 78 mm Shank diameter: 32 mm Shank / mounting length: 58 mm Total length: 175 mm Weight: 1.007 kg Design / Special features Compatible insert manufacturers: Taegutec, YG‑1 Indexable drill body for replaceable inserts Balanced geometry for reduced vibration FAQ Which inserts fit this drill body? The U939TM accepts SPMG 1104 indexable inserts; compatible suppliers include Taegutec and YG‑1. What holder size is required for mounting? A 32 mm shank diameter and 58 mm mounting engagement are specified for secure clamping of the tool body. How deep can this tool drill in one pass? The tool body provides a 78 mm cutting length; the achievable penetration per pass depends on machine capability and chosen insert grade. Is the U939TM suitable for series production? Yes — the indexable design and quick insert changes make the U939TM well suited to series work where reduced downtime and repeatability are priorities. What advantages do indexable inserts provide over solid drills? Indexable inserts enable rapid edge replacement, lower cost per cutting edge and flexible selection of grades for different materials, all of which support consistent cycle times. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of a substantial 39 mm cutting diameter, a 78 mm cutting length and a robust 32 mm shank ensures dependable machining performance and consistent cycle times; purchase and supply handled reliably through Metav Werkzeuge for immediate integration into production. Teknik Makina Solid Drill U141TM — 39 mm diameter, 78 mm cutting length The Solid Drill U141TM is a heavy‑duty indexable‑insert compatible drilling solution designed for industrial machining where stable clamping and repeatable holemaking are required 39 mm cutting diameter 78 mm cutting length 32 mm shank diameter Compatible with Korloy WCM-06T3 inserts Stable clamping for repeatable holemaking The robust 32 mm shank and overall length of 175 mm provide a stable connection to the toolholder, reducing vibration and improving repeatability in series production. A solid construction and a weight of 1.006 kg contribute to consistent cutting engagement, which translates directly into fewer rejects and less rework. In production environments where dimensional consistency matters, the reinforced shank geometry supports higher process stability and predictable tool life. Indexable‑insert compatibility to cut downtime Designed for use with Korloy WCM‑06T3 inserts, the U141TM adopts an indexable approach that separates the cutting edge from the tool body. This means worn cutting edges can be replaced quickly without changing the entire drill body, reducing machine downtime and spare‑part complexity. The 78 mm cutting length enables deeper holemaking without multiple passes, while insert interchangeability supports fast on‑machine recovery and simplified inventory of cutting edges. Fast procurement and easier integration into CNC workflows Marked under eClass 21180201 and supplied with SKU U141TM, the tool is set up for straightforward inventory and procurement. The combination of standardised insert type, a familiar 32 mm shank interface and the clear dimensional data (39 mm diameter, 175 mm overall length) makes CAM programming and tool offset entry more predictable. Backed by Metav’s supply chain and stocking in Emmerich, the tool is suitable for workshops and industrial shops seeking dependable delivery and centralised sourcing for precision tooling. For procurement, technical queries or to arrange priority delivery of the Teknik Makina Solid Drill U141TM, contact Metav Werkzeuge in Emmerich for expert advice and reliable supply coordination. Technical data Article number: U141TM Manufacturer: Teknik Makina Product name: Solid drill (Vollbohrer) Data Diameter: 39 mm Overall length: 175 mm Cutting length: 78 mm Shank diameter: 32 mm Shank length: 58 mm Weight: 1.006 kg eClass: 21180201 Special features Compatible with Korloy WCM-06T3 inserts Indexable‑insert design SKU for procurement: U141TM FAQ Is this drill compatible with Korloy inserts? Yes. The Teknik Makina Solid Drill U141TM is compatible with Korloy WCM‑06T3 inserts and is supplied to accept that insert format for straightforward replacement. What hole size and depth does the tool support? The tool provides a 39 mm cutting diameter with a 78 mm cutting length and an overall length of 175 mm, enabling single‑pass drilling within that effective cutting depth. What are the shank and mounting requirements? The drill has a 32 mm shank diameter and a shank length of 58 mm; the toolholder must accept a 32 mm shank for secure clamping and repeatable positioning. How does indexable‑insert design help production? Indexable inserts such as the WCM‑06T3 allow rapid replacement of cutting edges without removing the whole drill body, reducing downtime and simplifying spare‑part management for the workshop. What identifying data is useful for procurement and CAM setup? Use SKU U141TM and eClass 21180201 for ordering and the dimensional data (39 mm diameter, 78 mm cutting length, 175 mm overall length) for CAM tool entry. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a robust 32 mm shank and a precise 3 mm cutting width for stable, low-vibration parting that extends insert life; order the parting tool clamp holder K682TM directly via Metav Werkzeuge or ask our consultants if needed Parting tool clamp holder K682TM — 32 mm shank, 3 mm cutting width (Teknik Makina) The Parting tool clamp holder is a clamp-style holder designed for parting and grooving operations in turning applications, offering secure mounting and compatibility with ZCC 4C ZT.D inserts 32 mm shank for secure lathe mounting 3 mm cutting width for precise parting Compatible with ZCC 4C ZT.D inserts Stable clamping for consistent parting quality The compact clamp design delivers a stable, low-vibration setup that supports repeatable results in serial turning tasks. With a 32 mm shank, the holder fits common lathe tool posts and reduces flex under cutting forces; this stability leads directly to longer insert life and fewer rejects. The mass of the unit, at 1.641 kg, further damps chatter during cut-off operations, turning machine time into reliable, measurable productivity gains. Engineers and workshop managers will appreciate the predictable behaviour when switching from roughing to finishing cuts. Narrow kerf and high cutting clearance for material-saving cuts A narrow 3 mm cutting width combined with a 50 mm cutting height offers a slim kerf that reduces material waste while allowing effective chip evacuation in most steels and non-ferrous alloys. The design supports fine parting and grooving tasks where minimal material removal and tight tolerances are required. The 250 mm overall length provides adequate reach for deeper or awkward set-ups without compromising rigidity, enabling precision finishing operations with less secondary machining. Fit and integration with existing tool systems The holder is specified with an S32S shank designation and pairs with standard clamp interfaces, so it integrates easily into established turning tool lines. It accepts ZCC inserts in the 4C ZT.D format and aligns with the holder designation 3C-R ZT.D, making insert selection straightforward and supply chains simpler. This compatibility minimises downtime for tool changes and reduces inventory complexity, which is advantageous in workshops seeking leaner logistics. Designed for everyday workshop reliability Manufactured to withstand routine industrial use, the clamp-style holder is a pragmatic choice for workshops and small production facilities that prioritise uptime. The combination of a secure clamp mechanism and standardised interface supports quick reindexing of inserts and efficient tool maintenance. The result is a dependable solution that balances durability with the operational ease required in high-mix, low-to-medium volume turning environments. Contact Metav Werkzeuge for supply and technical advice on the Teknik Makina parting tool clamp holder K682TM with its 32 mm shank and 3 mm cutting width; call +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: K682TM Manufacturer: Teknik Makina Dimensions & weights Shank diameter: 32 mm Overall length: 250 mm External diameter: 39 mm Cutting height: 50 mm Cutting width: 3 mm Weight: 1.641 kg Compatibility & features Compatible inserts: 4C ZT.D Compatible insert manufacturer: ZCC Shank designation: S32S Holder designation: 3C-R ZT.D FAQ Which inserts fit this holder? The parting tool clamp holder K682TM is specified for ZCC inserts in the 4C ZT.D format and works with the corresponding 3C-R ZT.D holder designation. What shank size is required for the tool post? The tool requires a 32 mm shank seat, noted as S32S, for correct mounting and to ensure the designed rigidity. How deep can the holder reach in typical setups? With an overall length of 250 mm and a cutting height of 50 mm, the holder supports deeper parting operations while maintaining stability. Is the holder heavy enough to reduce chatter? At 1.641 kg, the mass contributes to vibration damping and consistent parting performance in standard turning applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid holder with a 32 mm shank and a 5 mm cutting width for precise, repeatable grooving and parting operations; the 60 mm cutting height supports deeper engagement while the 250 mm overall length balances reach with rigidity. Order the K620TM grooving clamping holder via Metav Werkzeuge or consult the technical team for application advice. Grooving clamping holder K620TM — 5 mm cutting width, 32 mm shank (Teknik Makina) The Grooving clamping holder K620TM is a lathe-mounted parting and grooving tool holder engineered for secure clamping of 5C MGM indexable inserts and built for industrial turning operations Shank Ø 32 mm for stable mounting Cutting width 5 mm for narrow grooves Cutting height 60 mm for deeper engagement Compatible with 5C MGM indexable inserts Consistent clamping for repeatable parting performance The robust shank and clamping layout provide stable support during intermittent cuts, which reduces chatter and variation between cycles. With a 32 mm shank and a mass of 1.561 kg, the holder offers the rigidity required for consistent depth control and longer insert life. The S32S 5C‑R shank designation ensures compatibility with common lathe toolposts; this stability translates directly into improved process control and fewer rejected parts when machining repetitive grooves or parting components. Optimised geometry for narrow grooves and precision cuts A 5 mm cutting width paired with a 60 mm cutting height permits clean, narrow grooving and reliable parting where small kerf widths are essential. The narrow-cut configuration minimises material removal per pass, reducing cutting forces and heat generation. The holder’s geometry focuses load through the insert pocket, so the indexable insert is better supported during plunging cuts; this yields improved dimensional accuracy and a finer surface finish on the workpiece. Seamless integration with MGM clamping and Korloy inserts The clamping system is compatible with the MGM holder format and accepts 5C MGM indexable inserts from common suppliers such as Korloy, allowing easy replacement and inventory alignment across the shopfloor. The S32S 5C‑R shank and MGM interface enable straightforward mounting and exchangeability, helping maintenance teams to standardise tooling kits and reduce machine downtime for tool changes. Practical reach without compromising rigidity With an overall length of 250 mm and an outer diameter of 39 mm, the tool holder provides the reach required for off-centre grooving while maintaining sufficient stiffness for controlled cutting. This balance is particularly useful for small-batch production and mixed-series turning, where flexibility and tool life are equally important. The moderate weight supports vibration damping without imposing unnecessary load on the turret or toolpost. For expert guidance on applying the Teknik Makina K620TM grooving clamping holder in specific turning applications, contact Metav Werkzeuge for a technical consultation and delivery from our Emmerich warehouse Technical data SKU: K620TM Designation: Grooving clamping holder (Stechklemmhalter) Manufacturer: Teknik Makina Shank designation: S32S 5C-R Shank diameter: 32 mm Cutting width: 5 mm Cutting height: 60 mm Overall length: 250 mm Outer diameter: 39 mm Weight: 1.561 kg Compatible insert type: 5C MGM Compatible insert manufacturer: Korloy Holder family: MGM clamping system Application: Parting and grooving for lathe operations FAQ What insert types fit this holder? The K620TM accepts 5C MGM indexable inserts and is specified for the MGM clamping system; compatibility with Korloy 5C MGM inserts is indicated. Which shank size is required for mounting? The holder uses an S32S 5C‑R shank with a shank diameter of 32 mm, suitable for compatible lathe toolposts and turrets. How deep can this holder engage during parting operations? The design provides a cutting height of 60 mm, enabling deeper grooves and parting depths compared with shallow-height holders, while maintaining support for the insert. Is the K620TM suitable for short overhang applications? Yes — with an overall length of 250 mm and a compact outer diameter, the holder balances reach and rigidity for many turning tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Technical Data: Order Number: D720TM Item: Groving Holder usable with 3C TD Indexable Inserts of Taegutec Brand: Teknik Makina ISO Code: 2020 3C-R TD Numerical Representations: Weight: 0.398kg Total length: 125mm Additional Informattion Cutting Direction: rechts Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Compact, reliable and ready for routine assembly work: the compact design and the professional hex profile ensure efficient fastening with minimal tool weight, while procurement and support are available through Metav Werkzeuge for straightforward workshop supply. Allen key — compact metric hex key by Teknik Makina (SKU 3ALLENTM) A compact Allen key engineered for routine assembly and maintenance tasks in professional workshops and service environments Compact, lightweight design 0.1 kg Metric hex profile for standard fittings Manufactured by Teknik Makina Faster, neater fastening for everyday workshop tasks The compact design and the defined hex key geometry make this tool a practical choice for recurring fastening work in production, maintenance and assembly. The short profile reduces wobble and improves access in confined spaces, while the low mass contributes to reduced hand fatigue during repetitive tasks. The balanced combination of compact form and sturdy hex engagement supports reliable alignment and smoother operation, delivering measurable efficiency gains in small- to medium-scale workflows. Secure contact and repeatable engagement for fewer slips A correctly formed hexagon profile distributes torque across flat contact faces rather than corners, which reduces the risk of rounding fastener heads and improves repeatability when applying torque. This geometry explanation is useful for non-specialists: the wrench bears on six flats of the screw head, increasing contact area and lowering stress concentrations. For routine maintenance and light production work, that means fewer damaged fasteners and less rework — a direct saving in time and materials. Easy storage and quick portability for mobile technicians Weighing only 0.1 kg, the tool is tailored for technicians who value mobility without compromising on basic performance. The lightweight nature and compact footprint allow efficient tool organisation, keeping essential hex keys at hand in tool pouches or wall racks. For mobile service engineers and shop-floor technicians, this portability translates into faster job turnaround and a tidier toolbox, supporting a more organised workflow and less time spent searching for the right implement. Consistent supply and professional sourcing through Metav Sourcing this Teknik Makina item via Metav ensures access to a broad industrial portfolio and the benefits of a European distribution hub. Metav stands for democratisation of precision, combining decades of expertise with an expansive catalogue to reduce supplier complexity. With a long-standing customer base and transparent order handling from Emmerich, the partnership reinforces reliable supply for workshops and trade specialists seeking consistent quality and stock availability. For procurement and technical guidance on this Teknik Makina Allen key (SKU 3ALLENTM), rely on Metav Werkzeuge for targeted advice and dependable delivery from Emmerich — contact info@metav-werkzeuge.com or call +49 2822 7131930 for concise support. Technical data Article number: 3ALLENTM Name: Allen key Manufacturer: Teknik Makina Facts Weight: 0.1 kg eCl@ss: 21189290 Special features inbussschlussel: 3 Allen SKU: 3ALLENTM FAQ What does the product include? The product is listed as an Allen key set described by the field "3 Allen", indicating a package composition noted in the technical details for the Teknik Makina item (SKU 3ALLENTM). Is this suitable for professional workshop use? Yes, the hex profile and compact design make the item appropriate for routine professional assembly and maintenance tasks in workshop environments. How much does the tool weigh? The documented weight for the item is 0.1 kg, making it lightweight and easy to carry within a tool kit. Why is hex geometry important for fastening? Hex geometry increases contact area on the fastener flats, lowering stress on corners and helping to prevent rounding; this contributes to more reliable torque transfer and less rework. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com