Gibt es einen Hahn und Kolb Online Shop?

Take advantage of a compact, robust face milling solution that pairs compatibility with LOGU 0303 indexable inserts and a 40 mm diameter for stable, space-saving setups; the 16 mm shank and six cutting positions deliver long tool life and predictable uptime — order the face milling head directly via Metav Werkzeuge or ask our consultants if needed. Face milling head for LOGU 0303 indexable inserts — 40 mm diameter · 6 cutting edges · Teknik Makina A face milling head engineered for LOGU 0303 indexable inserts, designed for reliable face milling applications where compact dimensions and repeatable performance matter Face milling head for LOGU 0303 inserts 40 mm diameter for compact setups Six cutting positions for extended life 16 mm shank with T15 Torx fixing Stable compatibility that reduces setup uncertainty Built around the LOGU 0303 insert system, this milling solution accepts Kyocera-style indexable inserts and converts their proven cutting geometry into dependable face-milling performance. The head’s design accommodates the standard insert seating and clamping forces, which means less trial-and-error during tool setup and more predictable component tolerances. By choosing a head that matches the insert family, the machining process benefits from consistent chip control and a familiar regrind or replacement workflow, so production planners gain measurable process stability. Longer productive periods through indexed cutting positions The head features six cutting positions, allowing operators to rotate to a fresh edge rather than replace the entire insert immediately, extending service intervals and lowering tooling cost per component. Fast, secure retention is achieved with an M3x7 screw tightened with a T15 Torx key, simplifying maintenance routines and reducing changeover time. This configuration supports efficient workshop practices: when a cutting edge is worn, the insert is indexed quickly and the tool returns to cut within seconds, which helps to keep cycle times stable and reduces unscheduled downtime. Compact dimensions for rigid, space-efficient machining With a 40 mm diameter and an overall height of 40 mm combined with a 16 mm shank, the head is deliberately compact to suit small to medium milling spindles and tight fixtures. The reduced overhang improves rigidity and vibration resistance, contributing to better surface finish and extended insert life compared with larger, more cantilevered arrangements. The compact format also makes the head a practical choice for workshops looking to standardise tooling across multiple machines without sacrificing accessibility or repeatability. For technical advice or to secure fast supply of the Teknik Makina face milling head compatible with LOGU 0303 indexable inserts, contact Metav Werkzeuge in Emmerich by e-mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: T731TM Manufacturer: Teknik Makina Compatible system: LOGU 0303 / Kyocera indexable inserts Torx key: T15 Fixing screw: M3x7 Facts Diameter: 40 mm Overall height: 40 mm Shank diameter: 16 mm Cutting edges: 6 Special features Face milling application Compact design for small spindles Secure Torx clamping system Suitable for indexed insert rotation FAQ What inserts does this head accept? The face milling head accepts LOGU 0303 indexable inserts, matching Kyocera-style insert geometry for reliable seating and chip control. How is an insert secured in the head? Inserts are fixed with an M3x7 screw tightened using a T15 Torx key; the design permits quick indexing and secure clamping. Which machines suit this face milling head? Compact to medium milling spindles with a 16 mm tool holder or collet are appropriate, where the 40 mm diameter supports rigid, space-efficient setups. How many usable edges are available before replacement? The head accommodates inserts with six cutting positions, enabling multiple edge indexes to extend effective tool life. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, performance-oriented design with internal coolant and a 40 mm diameter to improve machining consistency and reduce thermal load. Order the cutter directly via Metav Werkzeuge or consult the Metav team for application support. Face milling head T362-1TM — 40 mm diameter with internal coolant for SDMT 09T3 indexable inserts (Teknik Makina) A robust face milling head engineered for precise face milling operations with SDMT 09T3 indexable inserts, offering a compact 40 mm design and integrated coolant feed for improved insert life. 40 mm diameter for compact setups Internal coolant for improved tool life Four cutting edges for efficient material removal High material-removal efficiency in a compact package The compact 40 mm design delivers concentrated cutting performance where space is limited without compromising stability. With four cutting edges, the tool enables balanced load distribution across inserts, which reduces vibration and supports consistent surface finish. The relatively low mass of 0.215 kg contributes to a fast-reacting tool system, helping to maintain spindle performance during light-to-medium face milling tasks. This combination of geometry and mass translates into improved machining throughput and predictable process behaviour in production environments. Integrated cooling and secure fixing for longer service life Built-in internal coolant directs cutting fluid close to the cutting zone, lowering temperatures at the edge and promoting chip evacuation. The result is reduced thermal wear on the insert seat and extended interval between changes. Inserts are secured with M3.5x8.5 Torx screws, tightened using a T15 key, ensuring a repeatable and secure clamping interface. Clear specification of fastening hardware simplifies maintenance planning and reduces downtime for insert changes, supporting uninterrupted workflows on the shop floor. Simple compatibility and easy workshop integration Designed to accept SDMT 09T3 indexable inserts and optimised for inserts from ZCC, the head integrates with common insert inventories to reduce tooling complexity. The overall length of 40 mm facilitates use in compact toolholders while preserving accessibility for maintenance. The head is manufactured by Teknik Makina and configured for straightforward replacement of cutting edges, which helps maintain operational readiness and aligns with centralised procurement strategies for cutting tools. Contact Metav Werkzeuge for tailored advice on deploying the Teknik Makina T362-1TM face milling head with internal coolant and for reliable supply from Emmerich. Technical data SKU: T362-1TM Product type: Face milling head Label: 40 mm face milling head SDMT 09T3 L40mm with internal coolant Manufacturer: Teknik Makina Core specifications Diameter: 40 mm Overall length: 40 mm Weight: 0.215 kg Cutting edges: 4 Internal coolant: yes Torx screw: M3,5x8,5 Torx key: T15 Compatibility & features For indexable inserts: SDMT 09T3 Suitable insert supplier: ZCC Product family: Face milling components FAQ What inserts fit this milling head? The T362-1TM accepts SDMT 09T3 indexable inserts; the head is specified for compatibility with inserts from ZCC. Is the head supplied with mounting screws? Mounting uses M3.5x8.5 Torx screws (Torx T15); check the delivery contents with the order to confirm included fasteners. Does the tool support coolant-through operation? Yes, the cutter head features internal coolant to deliver fluid close to the cutting edge for improved thermal control. What are the physical dimensions to consider for toolholder selection? Key dimensions are 40 mm diameter and 40 mm overall length; use these values when selecting a compatible holder. Who manufactures the product and who supplies it in Europe? The head is manufactured by Teknik Makina and supplied in Europe via Metav Werkzeuge for dependable logistics and quality filtering. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, reliable cutter head that combines precise geometry, broad insert compatibility and fast serviceability for steady production. With a 45° cutting angle and a 16 mm shank it delivers controlled material removal and straightforward integration into existing toolholders — order the component via Metav Werkzeuge or consult our technical team for tailored advice. Face milling head T319TM – compact cutter for SNKX 1206 indexable inserts (Teknik Makina) Face milling head T319TM is a compact cutter designed for SNKX 1206 indexable inserts, providing a 45° cutting angle for efficient face milling in confined setups For SNKX 1206 indexable inserts 45° cutting angle, three cutting edges 16 mm shank, Ø cutting up to 53 mm Torx fixing M4x12.5 with T15 key Faster, more consistent face milling with proven geometry The head is engineered to increase throughput while maintaining surface quality. The 45° cutting angle reduces axial load and encourages favourable chip evacuation, which supports higher feed rates without compromising finish. Combined with the three cutting edges and max cutting diameter 53 mm, the design balances material removal rate and tool life, offering a measurable improvement in cycle stability for repetitive face‑milling operations. Simplified stocking and flexible carbide choices Compatibility with the SNKX 1206 insert format reduces inventory complexity and supports rapid replacement. The cutter accepts inserts from common carbide suppliers such as Böhlerit, Korloy, Palbit, which allows selection of grades tailored to alloy and finish requirements. This standardisation helps procurement and workshop managers streamline tool rotation and reduces downtime caused by waiting for specialised inserts. Quick, repeatable mounting that reduces downtime Mounting is straightforward and engineered for repeatability: the head fits a 16 mm shank and secures inserts with a M4x12.5 Torx screw operated by a T15 key. The Torx fixation gives consistent clamp torque and makes insert changes fast and reliable. At approximately 0.417 kg and with a total length of 45 mm the assembly is compact, which helps to limit overhang and vibration on smaller milling centres, supporting stable cutting conditions. Built for workshop reliability and straightforward integration Manufactured by Teknik Makina, the cutter head combines robust construction with a compact footprint to suit both small production runs and series manufacture. The standardised interface and familiar insert format make retrofit into existing tool systems straightforward, reducing setup time. For customers in Europe, Metav Werkzeuge provides a quality‑screened supply chain from its Emmerich base, ensuring dependable availability and consistent parts handling. Discuss integration of the Teknik Makina face milling head T319TM with Metav Werkzeuge — call +49 2822 7131930 or email info@metav-werkzeuge.com for specific application guidance and supply options Technical data Article number: T319TM Manufacturer: Teknik Makina Description: for SNKX 1206 Indexable Inserts Facts Shank diameter: 16 mm Max cutting diameter: 53 mm Body diameter: 40 mm Total length: 45 mm Weight: 0.417 kg Cutting angle: 45° Number of cutting edges: 3 Special features Compatible inserts: SNKX 1206 Compatible manufacturers: Böhlerit, Korloy, Palbit Torx screw: M4x12.5 Torx key: T15 Brand: Teknik Makina FAQ Which insert type fits this cutter head? The T319TM face milling head accepts SNKX 1206 indexable inserts and is designed around that standard format. What is the maximum cutting diameter achievable? Maximum cutting diameter is 53 mm, which defines the practical face‑milling width for this head. How are inserts secured in the head? Inserts are fixed with an M4x12.5 Torx screw; a T15 key provides consistent clamping torque for secure assembly. What shank or holder size is required? The head uses a 16 mm shank interface, suitable for holders and adaptors that accept that diameter. Which materials and applications suit this cutter head? The cutter head is intended for face milling and finishing applications where SNKX 1206 inserts are appropriate; choice of carbide grade (from suppliers such as Böhlerit, Korloy, Palbit) determines suitability across steels and general workshop materials. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high‑performance face milling solution: a robust Ø40 mm head with six cutting edges and a 16 mm shank that boosts material removal while keeping tool changes quick. Order directly via Metav Werkzeuge or consult our specialists for application matching. Face milling head for LNMU 0303 indexable inserts – compact Ø40 mm, 6 edges by Teknik Makina A face milling head engineered for precise, high‑efficiency face milling with LNMU 0303 indexable inserts in compact toolholders and demanding workshop environments Compact face milling head Ø40 mm Six cutting edges for high removal rates 16 mm shank for secure toolholder fit Compatible with TNGLY‑OKE LNMU 0303 inserts Faster stock removal with minimal downtime The compact Ø40 mm cutting head delivers high metal removal in confined setups by distributing cutting forces across six cutting edges, so each insert carries a reduced load. Because the head accepts LNMU 0303 indexable inserts, the cutting tips are replaceable, avoiding full‑tool changes and significantly reducing machine downtime. For production planners this means predictable cycle times and fewer interruptions during multi‑part batches. Secure mounting and straightforward maintenance for reliable production A 16 mm shank ensures a tight fit into standard toolholders, improving run‑out stability and surface finish. Fixing is by M2.5×7 Torx screws accessed with a T8 Torx key, enabling quick insert swaps and controlled torque application. The design reduces the risk of incorrect clamping and supports repeatable set‑ups, which is especially beneficial for workshops aiming for consistent component tolerances and lower rework rates. Proven compatibility and application flexibility Designed specifically for LNMU 0303 style inserts and compatible with TNGLY‑OKE grades, the head suits a range of finishing and semi‑roughing tasks across ferrous and non‑ferrous materials (application to specific alloys depends on the chosen insert grade). The combination of a compact diameter, multiple cutting edges and standardised fixing means the tooling is flexible enough for tight‑access operations while maintaining efficient chip evacuation and cutting stability. For supply, technical matching or to discuss suitable insert grades for specific materials, contact Metav Werkzeuge to benefit from fast delivery and experienced application advice. Technical data SKU: T728TM Manufacturer: Teknik Makina ECLASS: 21180902 Core dimensions Diameter: 40 mm Overall height: 40 mm Shank diameter (D): 16 mm Cutting edges: 6 Designs / special features For LNMU 0303 indexable inserts Compatible inserts manufacturer TNGLY‑OKE Torx key size T8 Torx screw M2.5×7 Suitable for demanding machining, long tool life FAQ What insert type does this head accept? The face milling head accepts LNMU 0303 indexable inserts and is verified for use with TNGLY‑OKE inserts to ensure correct fit and performance (SKU T728TM, Teknik Makina). Can the head be used in compact toolholders? Yes, the 16 mm shank is intended for compact toolholders and provides secure mounting for stable machining with the face milling head (Teknik Makina, T728TM). How are inserts attached and replaced? Inserts are secured with M2.5×7 Torx screws and serviced using a T8 Torx key, allowing rapid replacement of worn cutting tips on the LNMU 0303 system (face milling head by Teknik Makina). Is this head suitable for heavy roughing? The head is designed for efficient face milling and semi‑roughing when paired with the appropriate LNMU 0303 insert grade; selection of the correct insert material and geometry determines suitability for heavy roughing. Manufacturer/Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a purpose-built face milling solution that combines precise insert compatibility with straightforward maintenance: the compact design supports efficient face milling using WNMX 09T3 indexable inserts and secures reliably via Torx fastening for reduced downtime. Order directly via Metav Werkzeuge or consult our technical team for application advice. T669TM face milling head – 40 mm diameter, for WNMX 09T3 inserts (Teknik Makina) A T669TM face milling head engineered for efficient face milling with WNMX 09T3 indexable inserts, suitable for light to medium-duty surfacing and finishing operations on production machines Compatibility with Korloy WNMX 09T3 inserts 40 mm diameter for broad face coverage Four cutting edges for stable material removal 16 mm shank for secure clamping Reliable insert compatibility for repeatable set-up The compact face milling head is matched to the widely used WNMX 09T3 indexable insert, ensuring fast, repeatable set-up across machines that accept a 16 mm tool bore. Built for straightforward insert changes, the head secures inserts with Torx M3x7 screws tightened with a T8 key, reducing changeover time and helping to maintain consistent tool geometry. Compatibility with Korloy inserts provides access to established cutting grades and geometries without bespoke tooling, which streamlines procurement and keeps spares simple. Consistent machining performance and low downtime Engineered with four cutting edges, the cutter head distributes cutting forces to reduce vibration and promote even wear, supporting steady surface finish quality during face milling passes. The geometry and mass balance of the head contribute to smoother spindle loads; at approximately 0.213 kg, the component is light enough to avoid unnecessary added inertia while still robust enough for routine production use. Fast, repeatable insert changes via the Torx fastening system minimise machine downtime and support higher productivity in batch and series manufacture. Practical design that supports production reliability With a 40 mm diameter and a total length of 40 mm, the head provides good face coverage while maintaining accessibility in compact set-ups. The 16 mm clamping diameter secures the head in standard toolholders for rigid positioning and repeatable concentricity. Supplied by Teknik Makina and distributed through Metav Werkzeuge, the component is intended as a straightforward replacement or upgrade for existing systems where WNMX 09T3 inserts are already in use, helping workshops and production lines to maintain continuity with proven insert solutions. Choose the Teknik Cutting Tools T669TM for dependable face milling with WNMX 09T3 inserts and contact Metav Werkzeuge for tailored advice and prompt supply from Emmerich – email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: T669TM Product: Face milling head (Planmesserkopf) Compatible inserts: WNMX 09T3 (Korloy) Manufacturer: Teknik Makina Core data Diameter: 40 mm Overall length: 40 mm Shank / bore diameter: 16 mm Cutting edges: 4 Weight: 0.213 kg Features and compatibility Torx screw: M3x7 Torx key: T8 Suitable for Korloy WNMX 09T3 indexable inserts Intended for face milling operations FAQ Which inserts fit this milling head? The T669TM face milling head accepts WNMX 09T3 indexable inserts; Korloy inserts in that format are directly compatible. What shank diameter is required for mounting? The head requires a 16 mm shank/clamping diameter for secure mounting in the toolholder. How many cutting edges does the cutter head provide? This milling head is equipped to use inserts that provide four cutting edges, enabling balanced material removal. Which fastening tools are needed for insert changes? Insert retention uses Torx M3x7 screws; a T8 key is required for tightening and loosening. Is the T669TM suitable for production environments? Yes, the T669TM face milling head is designed for reliable, repeatable set-up and quick insert changes, making it suitable for production use where WNMX 09T3 inserts are employed. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the HF13TM's combination of compact dimensions, high cutting-edge count and simple insert replacement to increase throughput while keeping maintenance time low; order directly via Metav Werkzeuge or consult the product specialists for integration advice. Igelfräser HF13TM — Rotary cutter head, Ø 40 mm, 18 cutting edges (Teknik Makina) The Igelfräser HF13TM is a rotary cutter head designed for indexable-insert milling with APKT 1003 inserts, offering a compact profile for profiling and high-feed surfacing on machines with a 32 mm toolholding interface. Ø 40 mm head diameter 18 cutting edges for smooth material removal Compatible with APKT 1003 inserts 32 mm shank for secure mounting Faster cycle times through increased cutting density A high tooth count is the central performance driver: with 18 cutting edges distributed on a compact Ø 40 mm head, chip load per edge is reduced while material removal remains efficient. The result is a more constant cutting force and reduced vibration, which translates into shorter cycle times and improved surface quality. The design is especially beneficial where frequent shallow passes are preferred over aggressive single cuts; quieter operation and lower spindle load contribute to extended tool life and more predictable production scheduling. Quick indexable-insert changes cut downtime The cutter accepts APKT 1003 indexable inserts from recognised suppliers such as Korloy, enabling rapid replacement of worn tips without remounting the entire tool. Insert retention uses Torx fastenings (M2.5x5.5), tightened with a T08 key, which simplifies maintenance and standardises workshop tooling. This indexable system reduces consumable costs compared with brazed or solid tools: only the small insert bodies are replaced, while the cutter body remains in service. Clear labelling of compatible inserts and standardised fixing hardware supports lean spare-part management and faster operator training. Stable mounting and predictable geometry for consistent results Mechanical stability starts with the connection: a 32 mm shank provides a robust interface for many common toolholders, while the 55 mm cutting height and 150 mm overall length offer a practical balance between reach and rigidity. The cutter's mass (approximately 1.1 kg) helps damp minor resonances, and the compact overall geometry reduces deflection at typical feed rates. For production environments where repeatability is essential, this geometry supports consistent component tolerances from part to part. Compatibility with standard insert formats also means known cutting parameters can be transferred quickly between machines. Contact Metav Werkzeuge for project-specific advice on integrating the HF13TM into existing toolsets and to arrange supply from our Emmerich warehouse — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: HF13TM Manufacturer: Teknik Makina Data Diameter: 40 mm Cutting edges: 18 Shank diameter: 32 mm Cutting height: 55 mm Overall length: 150 mm Weight: 1.1 kg Special features Compatible inserts: APKT 1003 Compatible insert manufacturer: Korloy Torx screw: M2.5x5.5 Torx key: T08 FAQ What inserts are compatible with this cutter head? The cutter head is designed for APKT 1003 indexable inserts; Korloy is listed as a suitable insert manufacturer for the HF13TM rotary cutter head. How is the insert secured and which tool is needed for changes? Inserts are retained by Torx screws (M2.5x5.5) and require a T08 Torx key for tightening and removal on the HF13TM. What shank diameter is required for mounting the cutter? The tool features a 32 mm shank diameter and is intended for holders compatible with that toolholding interface. Can the HF13TM be used for profiling and surface removal? Yes, the combination of 18 cutting edges and 55 mm cutting height makes the HF13TM suitable for profiling and controlled surface removal tasks where many small, stable cuts are preferred. What are the physical dimensions and mass of the cutter head? The HF13TM has a 40 mm head diameter, 150 mm overall length and weighs approximately 1.1 kg, providing a balance between reach and rigidity. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of high material removal rate, secure clamping and straightforward insert replacement for reliable machining performance; order the tool directly via Metav Werkzeuge or ask the consultants for tailored advice. Multi-insert rotary cutter HF18TM — Ø 40 mm, 18 cutting edges (Teknik Makina) A multi-insert rotary cutter HF18TM designed for efficient profiling and stock removal in CNC and milling applications, compatible with Korloy APXT 1003 indexable inserts. Ø 40 mm cutting diameter Compatible with Korloy APXT 1003 18 cutting edges for efficient stock removal 32 mm shank for secure clamping Faster, predictable material removal for production runs The HF18TM offers a Ø 40 mm cutting diameter combined with 18 cutting edges, delivering uniform chip formation and reduced cycle times compared with single-edge tools. High cutter occupancy allows for lower feed per tooth while maintaining throughput, which translates into improved surface consistency and predictable tool life. The design suits repetitive profiling and deburring where stable, repeatable results are required and where downtime must be minimised. Secure clamping and rapid serviceability for workshop efficiency A robust 32 mm shank and conservative overall geometry ensure secure fixture in conventional toolholders, reducing vibration and run-out during operation. Fast insert changes are enabled by the specified M2.5x5.5 Torx screw and T08 key, allowing maintenance to be completed with standard workshop tools. The result is lower setup time and a quicker return to productive machining, supporting tighter production schedules without complex procedures. Indexable inserts cut running costs and simplify logistics Designed for use with APXT 1003 indexable inserts from Korloy, the cutter lets shops replace only worn cutting edges rather than the entire head. This approach reduces tooling expenditure and minimises material loss during regrinds. The specified 55 mm cutting height provides ample engagement for aggressive stock removal while preserving a balance between cutting volume and insert life, making the solution cost-effective for medium- to high-volume operations. Practical dimensions for versatile integration and handling With a 200 mm overall length and a mass of 1.621 kg, the tool sits comfortably in standard machining envelopes and is uncomplicated to handle during changeover. The compact diameter and proven indexable-insert concept make the cutter suitable for retrofit into existing tool sets, keeping inventory manageable. Assembly and replacement follow typical industry procedures, so adoption requires minimal retraining of personnel. Contact Metav Werkzeuge today for a technical consultation or to arrange fast delivery from Emmerich; specialist advice and detailed product matching are available to ensure the HF18TM meets the specific process requirements. Technical data Article number: HF18TM Manufacturer: Teknik Makina Product name: Multi-insert rotary cutter SKU: HF18TM Core dimensions Diameter: 40 mm Shank diameter: 32 mm Cutting height: 55 mm Total length: 200 mm Number of cutting edges: 18 Weight: 1.621 kg Design & compatibility Compatible inserts: APXT 1003 Compatible insert manufacturer: Korloy Fixing screw: M2.5x5.5 Torx Required Torx key: T08 eCl@ss: 21180806 ETIM: EC011860 FAQ What insert type is required for this cutter? The cutter accepts APXT 1003 indexable inserts; Korloy-specified APXT 1003 is compatible with the HF18TM. How is the insert secured in the cutter? Inserts are retained by an M2.5x5.5 Torx screw; a T08 Torx key is used for tightening and replacement. Can the tool be used in standard milling holders? Yes, the 32 mm shank is intended for secure clamping in conventional toolholders common to milling machines. What maintenance is recommended to prolong cutter life? Regular inspection of inserts and correct torque on the fixing screws keeps the HF18TM running reliably; worn inserts should be replaced promptly to avoid uneven cutting. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust, indexable milling solution that combines a compact 40 mm diameter, 9 cutting edges and a 43 mm cutting height for stable material removal; order via Metav Werkzeuge or consult our experts for specification support. Indexable rotary cutter HF22TM — 40 mm diameter, 9 cutting edges (Teknik Makina) The indexable rotary cutter HF22TM is a compact milling head designed for use with APKT 1604 indexable inserts, suitable for general milling applications where fast insert changes and consistent cutting performance are required 40 mm diameter for compact milling heads 9 cutting edges for smoother material removal Compatible with APKT 1604 Korloy inserts Ø32 mm shank for secure machine mounting Consistent cutting performance with an indexable system The HF22TM is engineered as an indexable insert cutter to deliver repeatable results across short production runs and workshop tasks. Its 40 mm diameter and 9 cutting edges distribute cutting forces, reducing vibration and improving surface consistency. The 43 mm cutting height provides an extended engagement area, allowing each insert to contribute to material removal and increasing tool life through even wear. Designed for stability, the tool balances a compact footprint with sufficient cutting capacity to integrate into milling spindles or suitable tool holders. Fast insert replacement and low downtime An indexable system reduces the need for resharpening and keeps maintenance predictable. Inserts of the APKT 1604 style are secured with Torx M4x10 screws tightened by a T15 key, enabling quick changeovers and minimal setup time. The use of standardised inserts from Korloy simplifies stocking and replacement procedures. This approach translates into lower effective tooling costs and faster return to production when compared with full-solid tools that require regrinding. Secure mounting and workshop compatibility With a Ø32 mm shank and an overall length of 125 mm, the milling head provides a rigid connection to common holders and collets used in machine centres and milling spindles. The tool’s mass (0.821 kg) and geometry are balanced to reduce runout and ensure predictable cutting behaviour. The indexable concept combined with a compact form factor makes the cutter a practical option for workshops seeking to rationalise their tooling inventory while maintaining machining flexibility. Practical purchase and integration guidance Specification-focused purchasers benefit from objective data: the cutter accepts APKT 1604 inserts (Korloy), uses M4x10 Torx screws with a T15 key, and measures 40 mm in diameter with a 43 mm cutting height. For integration, select a clamping system that accepts a 32 mm shank and ensure the machine’s torque and speed range match the chosen inserts’ recommendations. Metav’s purchasing and technical teams can assist with matching insert grades and coolant strategies to the intended application. For tailored technical advice or to secure supply of the Teknik Makina HF22TM via Metav Werkzeuge, contact our specialists in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss machine compatibility and delivery options. Technical data Article number: HF22TM ECLASS: 21180806 ETIM: EC011860 Manufacturer: Teknik Makina Facts Diameter: 40 mm Cutting height: 43 mm Shank diameter: 32 mm Overall length: 125 mm Weight: 0.821 kg Cutting edges: 9 Special features Compatible with APKT 1604 indexable inserts Inserts manufacturer: Korloy Fixing screws: Torx M4x10 Torx key: T15 Manufacturer brand: Teknik Makina FAQ Which inserts are compatible with this milling head? The cutter accepts APKT 1604 indexable inserts; Korloy inserts are specified as compatible for the HF22TM. How are the inserts secured? Inserts are fixed with Torx M4x10 screws using a T15 Torx key for reliable clamping and straightforward replacement. What shank diameter is required for mounting? The tool has a Ø32 mm shank, so a holder or collet suitable for 32 mm is required for secure mounting. How many cutting edges does the tool provide and what is the benefit? The cutter provides 9 cutting edges, which helps distribute cutting forces and promotes smoother material removal with reduced vibration. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the high material removal rate from the combination of 12 cutting edges, a 40 mm cutting diameter and a 58 mm cutting height for consistent productivity. Secure clamping via the 32 mm shank and fast insert changes make the tool reliable for repetitive machining tasks; order the HF32TM through Metav Werkzeuge or contact our consultants for application advice. Igelfräser HF32TM — 40 mm indexable-insert milling cutter, 12 cutting edges (Teknik Makina) The Igelfräser HF32TM is an indexable-insert milling cutter designed for efficient roughing and semi-finishing in industrial toolrooms and production environments 40 mm cutting diameter 12 cutting edges for high stock removal Compatible with APKT 1604 inserts 32 mm shank for secure mounting Faster material removal with indexable inserts The cutter head is built around APKT 1604 indexable inserts, which enable rapid material removal while keeping running costs predictable. With 12 cutting edges, the design distributes cutting forces across multiple inserts, reducing vibration and extending the life of each insert. Indexable inserts mean downtimes are limited to quick insert changes rather than full tool regrinds, which improves machine uptime and lowers per-part machining costs. Compatibility with widely used insert sizes also simplifies inventory management. Ease of service and secure clamping for reliable production A 32 mm shank provides a stiff connection to standard toolholders, improving stability during heavy cuts and reducing chatter. Insert retention is accomplished with M4x10 Torx screws, tightened using a T15 key, which ensures quick and repeatable clamp force at each change. The straightforward screw-and-insert system reduces the time needed for routine maintenance and keeps set-up procedures simple, a practical advantage when cycle times and reproducibility matter. Stable geometry for consistent cut quality The cutter’s 40 mm diameter and 58 mm cutting height are balanced to allow deeper passes without sacrificing control. The 200 mm overall length offers reach where required, while the tool’s 1.28 kg mass contributes to dampening of minor spindle vibrations. These dimensional decisions translate into consistent surface results and predictable tool behaviour across batches, making the cutter suitable for repetitive production runs where part tolerance and surface integrity are priorities. Workshop compatibility and inventory efficiency Designed to accept inserts from established manufacturers such as Korloy, this milling head integrates easily into existing tool systems. The use of common insert forms like APKT 1604 reduces the need for bespoke consumables and enables rapid replenishment from standard suppliers. For engineers and buyers aiming to consolidate procurement without compromising on performance, the tool offers a practical balance between modularity and machining capability. Contact Metav Werkzeuge for application-specific guidance and to secure supply of the Teknik Makina HF32TM insert milling cutter with APKT 1604 compatibility Technical data Article number: HF32TM Manufacturer: Teknik Makina Product name: Igelfräser Compatible inserts: APKT 1604 (Korloy) Key dimensions Diameter: 40 mm Shank (d): 32 mm Cutting height: 58 mm Overall length: 200 mm Cutting edges: 12 Weight: 1.28 kg Special features Torx screw: M4x10 Torx key size: T15 Insert manufacturer compatibility: Korloy FAQ What type of inserts does this cutter accept? The HF32TM accepts APKT 1604 indexable inserts; the tool is compatible with inserts from Korloy and other suppliers offering the same designation. How many cutting edges are available and why does it matter? The cutter has 12 cutting edges, which spreads load across multiple inserts to increase removal rates and reduce vibration during heavy cuts. What shank size is required for mounting? The milling head uses a 32 mm shank diameter for secure mounting in standard toolholders, providing stiffness for stable machining. Which fastening parts are required for insert changes? Insert fastening uses M4x10 Torx screws and a T15 Torx key for quick and repeatable insert replacement. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the 90° geometry, secure Torx fastening and direct compatibility with ANHX 1206 indexable inserts for consistent right‑angle milling and low setup times; order the component directly via Metav Werkzeuge or consult the technical team for fitment advice. 90° Corner Milling Head for ANHX 1206 Indexable Inserts (Teknik Makina) — 16 mm shank, Torx M3.5×8.5 fastening The 90° Corner Milling Head for ANHX 1206 Indexable Inserts is a compact insert holder engineered for precise shoulder and face milling in CNC machining environments. 90° cutting angle for square operations Compatible with ANHX 1206 indexable inserts 16 mm shank for secure mounting Torx M3.5×8.5 fastening with T15 key Consistent right‑angle machining for repeatable production quality The 90° design delivers a reliable right‑angle approach that simplifies setup and reduces the need for additional fixture adjustments. With ANHX 1206 compatibility and a geometry optimised for square‑shoulder work, the head maintains a predictable tool path and repeatability across batches. This translates into fewer part reworks and a steadier process capability in series production. The provision of four cutting edges supports uninterrupted operation until the next indexed change, contributing to higher machine utilisation and lower per‑part manufacturing cost. Robust fastening and dimensions that cut changeover time A secure clamping concept is essential for stable cutting forces; the holder uses a Torx M3.5×8.5 screw tightened with a T15 key, ensuring consistent seat pressure and repeatable insert positioning. The 16 mm shank provides a compact but rigid connection to the toolholder system, while the 40 mm head diameter and 40 mm overall length balance accessibility in tight assemblies with the stiffness required for heavier cuts. At 0.248 kg, the head is light enough to limit spindle imbalance yet substantial enough to give a solid cutting feel. These dimensions reduce vibration and provide stable cutting conditions that improve surface finish and tool life. Suited to compact CNC setups and industrial workflows Designed for workshops and production lines that prioritise space and efficiency, the corner milling head integrates seamlessly into standard toolholding arrays and is a practical choice where square‑shoulder milling and face operations are frequent. Compatibility with Palbit‑type inserts (ANHX 1206) allows sourcing of proven grades for a variety of materials, enabling optimisation for aluminium, steel or cast components depending on the chosen insert grade. The compact design supports rapid index changes and straightforward inventory management, helping maintenance teams to keep cycles short and throughput high. Contact Metav Werkzeuge for compatibility checks and procurement of the Teknik Makina 90° corner milling head — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for personalised advice and fast delivery from Emmerich Technical Data Article number: T641TM Manufacturer: Teknik Makina Product: 90° corner milling head for ANHX 1206 indexable inserts Facts Shank diameter: 16 mm Head diameter: 40 mm Overall length: 40 mm Weight: 0.248 kg Cutting angle: 90° Number of cutting edges: 4 Special features Compatible inserts: ANHX 1206 Compatible insert manufacturer: Palbit Fastening screw: Torx M3.5×8.5 Torx key size: T15 FAQ What inserts fit this milling head? The head is designed for ANHX 1206 indexable inserts; compatible grades from Palbit are commonly used for versatile performance. Is the shank suitable for standard toolholders? The 16 mm shank diameter matches common compact toolholder systems and offers a rigid connection for reliable machining. How is the insert secured? Inserts are fixed with a Torx screw (M3.5×8.5) tightened with a T15 key, providing repeatable clamping and precise seating. Can the head be used for both shoulder and face milling? Yes; the 90° geometry and balanced dimensions make it suitable for square‑shoulder operations and face milling tasks in series production. What is the SKU for ordering and reference? Reference T641TM when enquiring about the Teknik Makina 90° corner milling head for ANHX 1206 inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust 90° solution with precise compatibility for APMT 0602 indexable inserts and a compact 16 mm shank that reduces vibration and set-up time — order directly via Metav Werkzeuge or consult our specialists for integration support. Corner turning head — 90° indexable turning head with APMT 0602 compatibility (Teknik Makina) The corner turning head is designed for precise external corner turning and face finishing in CNC turning applications using APMT 0602 indexable inserts 90° geometry for precise corner turning Compatible with APMT 0602 indexable inserts 16 mm shank diameter for stable clamping Torx T6 mounting with M2x4.2 screw Accurate 90° geometry for consistent corner finishing The 90° tool geometry delivers a repeatable cutting angle that simplifies set-up and reduces secondary finishing. With a focus on process stability, the head’s 90° orientation is matched to standard APMT 0602 inserts so that edge engagement is predictable and surface integrity is preserved. This orientation shortens cycle times by enabling straightforward toolpaths for corner relief and profiling, providing a measurable gain in throughput for batch and single-piece production. Secure fastening and fast insert changes to keep cycles moving A Torx T6 retention and an M2x4.2 screw provide reliable clamping for the indexable insert, enabling quick changeovers without compromising rigidity. The compact 16 mm shank ensures a tight fit in standard toolholders, reducing micro-movement under cutting loads. Reduced downtime for insert replacement and secure mounting translate directly into higher machine utilisation and lower process variation in serial production. Stiff, compact construction for improved surface quality With a 40 mm diameter and a 40 mm overall height, the head balances stiffness with compactness to fit tight tool arrangements while resisting deflection. The robust form factor supports consistent chip formation and tool life extension when used with quality carbide inserts from compatible manufacturers such as Korloy. This mechanical stability helps to maintain surface finish requirements and reduces the frequency of rework in high-precision turning tasks. Built for compatibility across workshop workflows The head accepts APMT 0602 indexable inserts and integrates into existing turning tool systems with minimal modification. Its design supports quick retrofitting into established processes, making it suitable for job shops and production lines that demand predictable results from modular tooling solutions. The combination of standardised insert geometry and a reliable clamping concept assists process engineers in achieving consistent part accuracy across runs. For a reliable 90° turning solution from Teknik Cutting Tools, contact Metav Werkzeuge for tailored advice and assured supply from Emmerich: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: T596TM Brand: Teknik Makina Product type: 90° corner turning head for APMT 0602 indexable inserts Core technical data Diameter: 40 mm Overall height: 40 mm Shank diameter (take-up): 16 mm Number of cutting edges: 10 Compatibility: APMT 0602 inserts Special features Compatible insert manufacturer: Korloy Mounting screw: M2x4.2 Torx key size: T6 Indexable insert type: APMT 0602 Angle: 90° FAQ What insert type does this head accept? The corner turning head accepts APMT 0602 indexable inserts, fitted and secured using the specified Torx T6 screw arrangement. Is the shank suitable for standard toolholders? The head features a 16 mm shank diameter designed for stable clamping in compatible toolholder systems. Which insert manufacturers are compatible? Compatibility is specified for Korloy APMT 0602 inserts; the head is designed around that insert geometry for optimal fit. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, 90° corner turning head that is built for reliable right‑angle operations with ADMT 1204 indexable inserts, combining secure clamping and simple integration to keep machining cycles efficient — order directly via Metav Werkzeuge or consult our specialists for application advice. Corner Turning Head 90° T214TM — for ADMT 1204 indexable inserts, 16 mm shank (Teknik Makina) The Corner Turning Head T214TM is a 90° turning tool head designed for precision right‑angle turning on lathes and CNC machines, intended for use with ADMT 1204 indexable inserts. 90° cutting geometry for right‑angle turning Compatible with ADMT 1204 indexable inserts 16 mm shank for secure mounting Torx M3x7 clamping screw, T8 key required Consistent right‑angle performance for turning operations The 90° geometry delivers a dependable cutting orientation that simplifies fixture planning and reduces set‑up complexity. Fitted for ADMT 1204 indexable inserts, the tool head provides a stable engagement point that helps reduce chatter and improves surface finish on shoulder and face machining. The compact geometry supports predictable tool behaviour, which contributes to shorter cycle times and higher process reliability for repetitive production runs. Simple mounting and secure clamping for fast changeovers Designed with a 16 mm shank and a modest overall length of 45 mm, this tool head slots into conventional toolposts and turret stations without the need for special adapters. The clamping is achieved with a Torx M3x7 screw (Torx key T8), enabling quick, repeatable insert fixation and easing maintenance routines. At 0.28 kg, the head is light enough to limit inertia but robust enough to withstand normal turning forces, supporting stable cutting and minimal tool deflection. Workshop efficiency through compatibility and durability Compatibility with Walter ADMT 1204 inserts ensures wide availability of insert grades and geometries, allowing shops to match insert specification to material and operation. The compact diameter (40 mm) and the nominal cutting angle make this head suitable for confined setups where a right‑angle approach is required. Built for regular production use, the head supports efficient insert indexing and predictable tool life, contributing to overall cost efficiency and reduced downtime in busy turning environments. Contact Metav Werkzeuge for tailored advice on integrating the T214TM corner turning head into existing tool systems and to request detailed technical data from our Emmerich team. Technical Data SKU: T214TM Manufacturer: Teknik Makina Article name: Corner turning head T214TM For indexable inserts: ADMT 1204 Compatible insert brand: Walter Cutting angle: 90° Dimensions & weight Diameter: 40 mm Overall length: 45 mm Shank diameter: 16 mm Weight: 0.28 kg Fixing & compatibility Torx screw: M3x7 Torx key size: T8 ECLASS: 21181015 Number of cutting edges (insert format): 4 FAQ What inserts fit this turning head? The corner turning head is designed for ADMT 1204 indexable inserts and is compatible with the ADMT format offered by Walter. Which shank size is required for mounting? A 16 mm shank seat is specified for the T214TM; the compact shank supports secure mounting in standard toolposts. What torque or key is used to clamp the insert? Clamping is performed with a Torx M3x7 screw; a T8 Torx key is required for tightening. Is the head suitable for right‑angle shoulder and facing operations? Yes — the 90° geometry of the head ensures consistent right‑angle engagement for shoulder turning and facing tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a compact 40 mm diameter, internal coolant and compatibility with RPMT 10T3 indexable inserts for efficient and reliable milling; order the cutter directly via Metav Werkzeuge or ask our consultants if needed. Round indexable cutter T706-1TM — 40 mm diameter with internal coolant (Teknik Makina) Round indexable cutter T706-1TM for high-efficiency face milling with RPMT 10T3 indexable inserts and integral coolant supply. Compact 40 mm diameter for tight setups Internal coolant for improved tool life Compatible with RPMT 10T3 indexable inserts Five cutting positions for continuous operation Compact design that boosts throughput The 40 mm cutter diameter and compact overall length make this tool ideal for confined setups where space and access are restricted. As a round indexable cutter, it houses five indexable inserts, allowing for continued operation with minimal interruption when a single insert is changed. The design reduces set-up time and supports steady material removal rates, which contributes to predictable cycle times and consistent throughput on the shopfloor. Coolant-through feature for controlled temperatures The integrated internal coolant channel delivers coolant directly to the cutting zone, reducing temperatures at the insert edge and improving chip evacuation. This targeted lubrication helps to preserve insert geometry and extends service intervals, resulting in fewer unplanned stops. For operations where thermal stability affects surface finish and dimensional accuracy, the coolant-through design provides a measurable performance advantage over external-only cooling. System compatibility and quick insert changes Made for RPMT 10T3 indexable inserts and compatible with Korloy-made inserts, the cutter simplifies tooling logistics by using a widely available insert type. The tool’s five cutting positions provide balanced cutting forces and a stable cutting run, while indexable inserts enable fast replacement without complex regrinding. Lightweight at 0.24 kg, the milling head is easy to handle during tool changes and tool magazine loading, reducing ergonomic strain and saving valuable time in production routines. Proven partner quality and supply reliability Produced by Teknik Makina, this round indexable cutter combines practical construction with industry-standard insert compatibility, making it suitable for diverse milling tasks. Supplied via Metav Werkzeuge, customers benefit from a dependable European supply channel and expert advice from a precision partner that supports workshops with a broad product range and a promise of consistent quality and transparent order handling. Contact Metav Werkzeuge for application guidance and fast supply of the Teknik Makina T706-1TM; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: T706-1TM eClass: 21180902 Label: 40mm Rundplattenfräser RPMT 10T3 L40mm mit Innenkühlung Manufacturer: Teknik Makina Core data Diameter: 40 mm Overall length: 40 mm Cutting edges: 5 Weight: 0.24 kg Special features Internal coolant For RPMT 10T3 indexable inserts Compatible with Korloy inserts Product type: Round indexable cutter FAQ What insert type does this cutter accept? The cutter accepts RPMT 10T3 indexable inserts; it is compatible with Korloy-manufactured RPMT 10T3 inserts for straightforward sourcing and replacement. How does the internal coolant improve performance? The internal coolant delivers coolant directly to the cutting zone, lowering cutting temperatures and improving chip control, which helps to extend insert life and maintain surface quality. How many cutting positions are available on the tool? The milling head provides five cutting positions, enabling continued machining with rapid insert indexing and reduced downtime for maintenance. Is the tool suitable for tight or confined machining setups? With a compact 40 mm diameter and a short overall length, the cutter is designed for operations where space is limited and where a compact tool reduces interference and setup complexity. Who supplies the T706-1TM and where can application advice be obtained? The T706-1TM is supplied by Teknik Makina and distributed via Metav Werkzeuge; application guidance and order support are available from Metav Werkzeuge’s consultants. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the compact 40 mm diameter and compatibility with RDMT 1204 indexable inserts for efficient small-diameter face milling; secure clamping with M3.5x8.5 Torx screws keeps changeovers fast and reliable. Order the 40 mm round insert milling head directly via Metav Werkzeuge or ask our consultants if needed. Round Insert Milling Head for RDMT 1204 – 40 mm, L40 The Round Insert Milling Head is a compact face milling solution designed for high-productivity machining with RDMT 1204 indexable inserts in constrained tool setups. Ø 40 mm cutting diameter Compatible with RDMT 1204 indexable inserts Four cutting edges for steady material removal Compact 40 mm overall length Increased throughput with a small footprint A small-diameter cutter that delivers measurable productivity gains: the combination of a 40 mm cutting diameter and 4 cutting edges allows stable chip formation and repeatable surface quality in short overhangs. The tool accepts RDMT 1204 indexable inserts, which are designed for fast, repeatable seating and consistent cutting geometry. For shops migrating from solid-tool strategies, this approach reduces inventory cost by using replaceable inserts, while maintaining the machining characteristics expected from a dedicated face milling head. The compact form factor also reduces tool vibration and contributes to longer insert life. Fast maintenance and secure assembly to cut downtime Maintenance is simplified by the use of standard Torx hardware and readily available screws: the head is secured with M3.5x8.5 screws accessed using a Torx T15 key, enabling quick insert replacement and secure clamping during operation. This reliable fastening system lowers the risk of assembly errors and minimises unplanned stops on the shop floor. The head’s modest mass and balanced design support predictable tool behaviour, helping to keep cycle times consistent across repeated production runs. Designed for tight setups and versatile workshop use With an overall length of 40 mm and a mounting bore of 16 mm, the cutter suits applications where restricted tool overhang and clearance are critical. The compact dimensions make it appropriate for face milling, light profiling and interrupted cuts where a short projection improves stability. The head integrates easily into existing toolholder systems used for face milling heads and is especially useful for job shops and production environments seeking a compact, indexable solution that fits into established workflows. For tailored application advice and reliable supply of Teknik Makina’s 40 mm round insert milling head, contact Metav Werkzeuge for expert guidance and prompt dispatch from Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: T139TM Label: 40mm Rundplattenfräser RDMT 1204 L40mm Product type: Round insert milling cutter Manufacturer: Teknik Makina ECLASS: 21180902 Facts Diameter: 40 mm Overall length: 40 mm Mounting bore: 16 mm Cutting edges: 4 Weight: 0.236 kg Torx key: T15 Screw: M3.5x8.5 Special features For RDMT 1204 indexable inserts Category: Face milling head (Planmesserkopf) Compact design for reduced overhang Secure Torx clamping system FAQ What inserts are compatible with this milling head? The milling head accepts RDMT 1204 indexable inserts; these inserts provide repeatable seating and are suited to the cutter’s geometry for stable chip control. How is the cutter fixed and serviced? Screws with the specification M3.5x8.5 are used and require a Torx T15 key for assembly and insert changes, allowing quick and secure maintenance. Which applications suit this 40 mm head best? The tool is tailored to compact face milling tasks, short overhang operations and situations where a small-diameter cutter improves stability and surface finish. Is the head suitable for interrupted cuts? Yes, the combination of 4 cutting edges and secure clamping makes the head capable of handling light interrupted cuts while maintaining insert life. What toolholders are compatible with the mounting bore? The head’s 16 mm mounting bore is compatible with standard holders designed for small-diameter face milling heads and short-projection set-ups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the secure Torx mounting, compact 40 mm cutting diameter and four cutting edges for consistent finishing in small-batch and serial milling operations; order via Metav Werkzeuge or consult our technical advisors for compatibility details. Round Insert Face Mill (Rundplattenfräser) T612TM — 40 mm, for RHKW 1204 Indexable Inserts (Teknik Makina) The Round Insert Face Mill is a compact milling cutter engineered for finishing and light material removal using RHKW 1204 indexable inserts, suitable for machine shops and production cells. 40 mm cutting diameter Four cutting edges for smooth material removal 16 mm shank for rigid clamping Compatible with Ingersoll RHKW 1204 inserts Reliable cutting performance for predictable cycle times The design delivers consistent chip control and repeatable geometry thanks to the cutter's balanced tool body and four cutting edges. A 40 mm cutting diameter combined with precise insert seating reduces vibration and supports stable finish quality on common steels and cast components. Where process reliability is paramount, the combination of a compact cutter and multiple cutting edges enables shorter cycle times with less rework, improving throughput in frequent short-run turning-to-milling operations. Fast, secure mounting and simple maintenance The head is fixed with a M4x10 Torx screw and a clamp screw M3.5, requiring only a T15 Torx key for insert changes and routine maintenance. This clamping concept shortens tool-change intervals and lowers downtime on the shop floor. The 16 mm shank provides a secure interface in standard toolholders, promoting stiffness during light-face milling. Clear mechanical connections also simplify inspection and reduce the risk of improper seating that can affect surface finish. Flexible integration into standard tool inventories Engineered for the RHKW 1204 indexable inserts and compatible with Ingersoll insert geometries, the cutter integrates easily into existing toolsets. The compact overall length of 40 mm makes it especially suitable where clearance is limited or where multiple tools must be arranged close together on the turret or milling spindle. Its balanced specification supports both finishing passes and modest material removal, giving production planners a compact option for mixed production demands. Confidence through established supply and support Supplied under Teknik Makina specifications and stocked for rapid dispatch, the tool benefits from reliable sourcing and clear technical data for procurement and quality checks. Documentation and spare-part references are available to support inventory management and process audits. For workplaces prioritising traceability, the SKU T612TM provides an unambiguous identifier for ordering and record-keeping. For assured compatibility with RHKW 1204 indexable inserts and to arrange procurement through Metav Werkzeuge, please contact Metav Werkzeuge GmbH at +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: T612TM Manufacturer: Teknik Makina Product: Round insert face mill (Rundplattenfräser) Facts Diameter: 40 mm Cutting edges: 4 Overall length: 40 mm Shank diameter: 16 mm Weight: 0.246 kg Torx screw: M4x10 Clamp screw: M3.5 Torx key: T15 Special features For RHKW 1204 indexable inserts Compatible with Ingersoll inserts Compact overall length for limited clearance applications Secure Torx fastening system FAQ What inserts does this cutter accept? The cutter is designed for RHKW 1204 indexable inserts and has been specified for compatibility with inserts from Ingersoll. Which toolholders suit the shank size? A 16 mm shank requires toolholders sized for a 16 mm shank; the tool's compact geometry simplifies integration into standard milling setups. How many cutting edges are available before indexing? The tool body accommodates inserts that provide four cutting edges, enabling multiple indexings before replacement. What is the article number for ordering and documentation? Order and reference with the SKU T612TM, which is used for stock management and procurement records. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, precisely engineered 90° turning solution with a 16 mm shank and secure Torx clamping for consistent, repeatable results; ideal where rigid mounting and compatibility with ADMT 1606 indexable inserts are required. Order the angle turning head directly via Metav Werkzeuge or ask our consultants if needed. Angle turning head T351TM — 90° toolholder for ADMT 1606 indexable inserts (Teknik Makina) Angle turning head T351TM for external turning applications, designed to accept ADMT 1606 indexable inserts and to provide a rigid 16 mm mounting for stable machining at a 90° cutting geometry. 90° cutting geometry for precise turning Compatible with ADMT 1606 inserts 16 mm shank for rigid mounting Torx M4x10 clamping with T15 key Consistent 90° geometry for predictable machining results The 90° cutting angle is integrated to deliver a repeatable cutting direction, which reduces setup variation and simplifies programme planning for batch production. Built for short overhangs, the compact head and its 16 mm shank increase stiffness at the cutting point, lowering vibration and improving surface finish. With a focus on process reliability, the design supports stable chip formation when paired with the correct ADMT 1606 grades, so cycle times and rework are reduced without sacrificing component accuracy. Secure clamping and compatible interface for quick changeovers Clamping is effected via a Torx M4x10 screw, driven with a T15 key, which ensures consistent torque and straightforward insert replacement. The head accepts ADMT 1606 indexable inserts and is declared compatible with Walter inserts, enabling flexible tooling choices across common insert ranges. The secure fastening method minimises micro-movement at the insert seat, supporting repeatability and extending tool life through uniform load distribution. Compact dimensions that support workshop efficiency With a diameter of 40 mm, an overall length of 45 mm and a mass of 0.258 kg, the unit is compact enough to be installed in tighter turret pockets while still offering sufficient mass for damping. The small footprint helps reduce tool overhang and allows closer tool-to-tool spacing in multi-station setups, which can shorten cycle times and improve throughput. The straightforward mechanical interface and common insert format make integration into existing CNC turning cells efficient and predictable. For procurement or technical advice on the Teknik Makina angle turning head T351TM, contact Metav Werkzeuge to discuss compatibility, delivery and ordering options — Metav's specialists will assist with selection and logistics. Technical data Article number: T351TM Manufacturer: Teknik Makina Facts Diameter: 40 mm Overall length: 45 mm Shank / mounting diameter: 16 mm Weight: 0.258 kg Cutting angle: 90° Compatible insert type: ADMT 1606 Number of cutting edges: 4 Special features Torx screw: M4x10 Torx key size: T15 Compatible with Walter inserts Compact design for reduced overhang FAQ Which insert type fits this toolholder? The angle turning head accepts ADMT 1606 indexable inserts; Teknik Makina's T351TM is made to work with that insert form and is compatible with Walter-manufactured ADMT 1606 grades. Is the head suitable for external turning on small diameters? Yes — the 90° geometry and compact form factor of the T351TM are intended for external turning operations where short overhang and high rigidity are required. What is the shank diameter and how does it affect mounting? The toolhead uses a 16 mm shank, providing a rigid connection to the turret or holder and improving stability compared with smaller-diameter tooling. How are inserts secured to the head? Inserts are clamped with a Torx M4x10 screw tightened using a T15 key, ensuring consistent torque and secure seating for reliable repeatability. What are the key dimensions and weight for setup planning? Key measures are a 40 mm diameter, 45 mm overall length and a weight of 0.258 kg, useful for assessing clearance and balance in multi-tool setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise 90° geometry and robust mounting to improve turning stability and repeatability; combined compatibility with Korloy WNGX 0806 inserts and straightforward Torx fastening ensures fast tool changes and reliable production. Order this turning head directly via Metav Werkzeuge or contact the consultants for tailored advice. 90° turning head T692TM — for WNGX 0806 indexable inserts (Teknik Makina) The 90° turning head T692TM is a compact toolholder engineered for stable, repeatable turning with Korloy WNGX 0806 indexable inserts in shop and industrial lathe applications. 90° cutting geometry for square turning 16 mm shank for stable mounting Compatible with Korloy WNGX 0806 inserts Requires T8 Torx key and M2.5x5.5 screw Predictable cutting performance through controlled geometry The 90° cutting geometry gives a defined cutting direction and steady tool engagement, which reduces chatter and improves surface finish stability. Designed for operations where consistent radial contact is essential, the turning head converts insert geometry into repeatable results. With a focus on throughput, the configuration supports steady material removal and reliable part tolerances, allowing process planners to predict cycle times more accurately. Fast, secure set-up that keeps machines running Installation and changeover are straightforward thanks to the 16 mm shank and accessible clamping features. The turning head accepts Korloy WNGX 0806 inserts and is fastened using the T8 Torx key with an M2.5x5.5 screw, enabling secure clamping and quick replacement of cutting edges. This straightforward interface reduces downtime during insert changes and makes the component suitable for both single‑operator shops and automated tool magazines. Compact dimensions with industrial robustness With a Ø40 mm diameter and overall height 40 mm, the holder fits tight tool stations while providing the rigidity expected in production environments. The design accommodates six cutting edges where applicable, offering balanced support for the insert and helping to distribute cutting forces evenly. Easy access to the fixing screw and clear mechanical seating mean routine maintenance is fast, supporting predictable tool life without the need for specialised service. Practical benefits for workshop efficiency and supply reliability The head is intended for routine turning tasks where compatibility and quick serviceability matter most. Supplied as a concise, well‑specified component, it helps reduce inventory complexity by matching common Korloy insert types. Combined with Metav’s European logistics and expert advice, the component becomes part of a dependable workflow: swift delivery from Emmerich, product advice, and a broad range of complementary tooling to streamline procurement and machine uptime. For dependable 90° turning solutions from Teknik Makina, contact Metav Werkzeuge for expert guidance and order support via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T692TM Manufacturer: Teknik Makina ECLASS: 21180902 Suitable for inserts manufacturer: Korloy Facts Shank diameter: 16 mm Diameter: 40 mm Overall height: 40 mm Cutting angle: 90° Number of cutting edges: 6 Special features Compatible with Korloy WNGX 0806 indexable inserts Fastening: M2.5x5.5 screw Torque tool: T8 Torx key SKU: T692TM FAQ What inserts fit this turning head? The turning head is compatible with Korloy WNGX 0806 indexable inserts; confirm insert size before ordering. Which tool is required to change the insert? Insert fastening uses an M2.5x5.5 screw that is driven with a T8 Torx key for secure clamping. What are the key mounting dimensions? Key dimensions include a 16 mm shank, Ø40 mm diameter and an overall height of 40 mm, suitable for compact tool stations. Can this head be used for heavy roughing cuts? The 90° geometry and robust shank provide stability for many turning tasks; match insert grade and machining parameters to the application. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust M16 screw connection, Ø40 mm cutting diameter and a three-edge cutter geometry for steady metal removal and reduced setup time; order directly via Metav Werkzeuge or consult the specialists for detailed application advice. Screw-in milling cutter VT242TM – Ø40 mm, M16 thread (Teknik Cutting Tools) The Screw-in milling cutter VT242TM is a screw-in cutter designed for use with SDMT 09T3 indexable inserts, delivering secure mounting and straightforward insert changes for workshop and light industrial milling tasks. Ø40 mm cutting diameter M16 screw connection Compatible with SDMT 09T3 inserts by ZCC Torx fastening M3.5x8.5, key T15 Secure mounting that keeps production running The M16 screw connection and 29 mm thread depth provide a mechanically robust interface that reduces runout and vibration during operation. With the Torx M3.5x8.5 fastening and a T15 key, clamp force is consistent and repeatable, which lowers the frequency of re-adjustments and shortens setup times. This mechanically sound design translates into more predictable machining results and fewer rejects when batches are repeated. The screw-in format also supports quick replacement of damaged holders without the need for complex fixturing. Insert compatibility engineered for consistent cutting Designed specifically for SDMT 09T3 indexable inserts, the tool accepts inserts from ZCC, ensuring a wide availability of cutting grades and geometries. The three-edge configuration offers balanced cutting forces and steady chip formation, while the 40 mm cutting height allows for effective engagement on a variety of workpiece profiles. Explaining the term: indexable inserts are replaceable carbide or coated cutting tips; using them minimises tooling costs because only the insert is exchanged when worn, not the entire tool body. Dimensions that favour rigidity and access With an Ø40 mm diameter and 69 mm overall length, the holder presents a compact yet stiff solution that resists deflection under load. The moderate mass of 0.253 kg contributes to reduced spindle imbalance and helps maintain surface finish quality at higher spindle speeds. These dimensions make the tool suitable for operations where accessibility in tight spaces matters, while still providing the necessary contact area to dissipate cutting forces effectively. The design therefore supports both productivity and component integrity. Practical features for efficient workshop routines The screw-in format and the clearly specified fastener (Torx M3.5x8.5) mean routine maintenance and insert changes are straightforward, helping to keep machine downtime to a minimum. The tool’s compatibility with standard SDMT 09T3 inserts enables quick sourcing of cutting grades for aluminium, steel or harder materials where appropriate grades are selected. Given the straightforward mechanical interface and commonly available Torx key size, inventory management is simplified and repair cycles are quicker, which supports steady throughput in a production setting. For assured compatibility with SDMT 09T3 indexable inserts and to discuss specification or ordering, contact Metav Werkzeuge in Emmerich for tailored advice and reliable supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: VT242TM Manufacturer: Teknik Makina Product: Screw-in milling cutter for SDMT 09T3 indexable inserts SKU: VT242TM Facts Diameter: 40 mm Overall length: 69 mm Cutting height: 40 mm Thread: M16 Thread depth: 29 mm Number of cutting edges: 3 Weight: 0.253 kg Special features Compatible inserts: SDMT 09T3 Compatible insert manufacturer: ZCC Torx screw: M3.5x8.5 Torx key: T15 Screw-in design Indexable inserts application FAQ Is the tool compatible with SDMT 09T3 inserts? Yes. The screw-in milling cutter VT242TM is designed specifically for SDMT 09T3 indexable inserts and accepts grades supplied by ZCC. What fastening is required for mounting the holder? The holder uses a Torx fastening M3.5x8.5 secured with a T15 key for consistent clamp force. What are the main dimensions to consider for machine setup? Key dimensions are a Ø40 mm cutting diameter and a 69 mm overall length; the thread is M16 with a 29 mm thread depth. How many cutting edges does the tool provide and what is the benefit? The tool features three cutting edges; this geometry balances cutting forces and supports steady chip evacuation for improved surface finish. Can the holder be used for different insert grades? Yes. The holder’s acceptance of SDMT 09T3 inserts allows selection of different grades for specific materials or cutting conditions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a rigid, indexable-insert solution that combines compatibility with Sandvik R390-1704 inserts and straightforward insert clamping for reduced downtime; order directly via Metav Werkzeuge or consult the technical team for application-specific guidance. S518TM — Shank milling cutter for R390-1704 indexable inserts by Teknik Makina, Ø 40 mm, shank Ø 32 mm The S518TM is a shank milling cutter designed for use with R390-1704 indexable inserts, offering robust geometry for demanding CNC milling tasks. Compatible with Sandvik R390-1704 inserts Ø 40 mm cutting diameter Shank Ø 32 mm and 45 mm cutting length Reliable insert system for flexible production The S518TM is engineered as an indexable insert solution, accepting the widely used R390-1704 style by Sandvik, which allows toolshops to balance economy and performance. The insert is secured with a Torx M3.5x8.5 screw operated with a T15 key, a common and robust clamping method that simplifies tool changes and reduces setup time. This arrangement supports fast replacement of cutting edges, keeping machines productive and tooling costs manageable. Geometry that stabilises material removal With a Ø 40 mm cutting diameter and a shank Ø 32 mm, the cutter provides a balance between cutting reach and rigidity; the 45 mm cutting length and 120 mm overall length give defined engagement depth while maintaining stability. The tool features a 90° cutting angle and four cutting edges, which together deliver even load distribution and consistent chip formation. The listed weight of 0.782 kg reflects a solid construction that assists repeatable performance in serial milling applications on CNC machines. Practical handling and production benefits Insert clamping with the specified Torx screw provides secure retention and straightforward maintenance, helping to keep throughput high in production environments such as toolrooms and milling centres. As a modular cutting tool, the solution lowers per-part costs because only inserts are replaced, not the entire cutter body. The design is therefore suited to workshops aiming for efficiency, predictable tool life and straightforward inventory management. For tailored technical advice or to arrange procurement of the Teknik Makina S518TM, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss compatibility, delivery and application support. Technical data SKU: S518TM Manufacturer: Teknik Makina Designation: Shank milling cutter for R390 1704 indexable inserts Suitable for inserts: R390-1704 Compatible insert supplier: Sandvik Facts Cutting diameter: 40 mm Shank diameter: 32 mm Cutting length: 45 mm Overall length: 120 mm Number of cutting edges: 4 Cutting angle: 90° Weight: 0.782 kg Special features Torx screw for insert clamping: M3.5x8.5 Torx key size: T15 Indexable insert system: R390-1704 Brand: Teknik Makina FAQ Which inserts fit this cutter? The S518TM accepts R390-1704 style indexable inserts, specified for use with Sandvik-compatible insert geometries. What are the key dimensions of the tool? The cutter has a 40 mm cutting diameter, 32 mm shank diameter, 45 mm cutting length and 120 mm overall length; weight is 0.782 kg. How are inserts secured in the cutter? Inserts are clamped with a Torx M3.5x8.5 screw, tightened or loosened using a T15 Torx key for quick and secure changes. For which applications is the cutter intended? The tool is designed for CNC milling operations that use indexable inserts and require a 90° cutting angle and the flexibility of replaceable cutting edges. Is this cutter compatible with Sandvik inserts? Yes, the S518TM is listed as compatible with Sandvik R390-1704 inserts and is prepared for their standard clamping hardware. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Specifications: Order Number: VT168TM Item: Modular End Mill usable with APKT 1604 Indexable Inserts of Korloy Brand: Teknik Makina Quantitative Specifications: Diameter: 40mm Cutting Edges: 4 Weight: 0.238kg Total length: 60mm Cutting Height: 35.5mm Thread: M16 Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Take advantage of stable turning performance, proven compatibility with TNMG 1604 indexable inserts and an extended reach that supports consistent cycle times; order the tool directly via Metav Werkzeuge or consult the advisers at Metav Werkzeuge for application guidance. Boring bar S32T MTQNR – MTWN for TNMG indexable inserts (Teknik Makina) The S32T MTQNR boring bar is a right‑hand toolholder designed for use with TNMG 1604 indexable inserts, offering rigidity and reach for medium‑duty external turning applications. S32T MTQNR shank Ø 32 mm 300 mm overall length for extended reach Compatible with TNMG 1604 indexable inserts Right‑hand cutting, 107.5° cutting angle Greater stability for consistent surface finish The S32T MTQNR boring bar is engineered to reduce chatter through a shank Ø 32 mm and a 40 mm outer diameter, delivering a stable connection between holder and insert. The 300 mm overall length provides the reach required for deeper external operations while maintaining rigidity; this combination helps to preserve tool life and improves repeatability of diameter tolerances across batches. For production environments, the reduced vibration directly translates into fewer reworks and more predictable throughput. Faster changeovers and efficient machining with indexable inserts Designed as an MTWN holder for TNMG 1604 indexable inserts, the tool supports quick insert replacement and economical tooling strategies. The compatibility with standard TNMG geometry allows use of a wide range of chipbreakers and grades, enabling optimisation by material and cut. The right‑hand cutting orientation and the 107.5° cutting angle balance clearance and cutting edge strength, which helps maintain stable cutting forces and longer edge life — a clear benefit when switching between roughing and finishing passes. Seamless integration into workshop routines and process reliability The toolholder's mass (approx. 1.821 kg) and ISO designation ensure predictable handling during set‑up and predictable balancing in rotating assemblies. The MTWN for TNMG indexable inserts format supports established clamping practices and simplifies inventory by aligning with commonly stocked TNMG inserts. For complex operations where fixture space and access matter, the boring bar’s geometry provides reach without excessive overhang, promoting safer toolpaths and easier programming for CNC lathes. Further technical details and application examples are available from Metav Werkzeuge to support process planning and tool selection. For reliable turning solutions from Teknik Makina and tailored application advice, contact Metav Werkzeuge in Emmerich — info@metav-werkzeuge.com or +49 2822 7131930 — to arrange procurement and integration support. Technical data Article number: K366TM Manufacturer: Teknik Makina Type designation: S32T MTQNR Product name: MTWN for TNMG Indexable Inserts ECLASS: 21180806 Facts Shank diameter: 32 mm Outer diameter: 40 mm Overall length: 300 mm Cutting height: 60 mm Cutting angle: 107.5° Weight: 1.821 kg Cutting direction: right Special features Compatible inserts: TNMG 1604 Holder format: MTWN ISO designation: S32T MTQNR Suitable for medium‑duty external turning SKU: K366TM FAQ Is this tool compatible with standard TNMG inserts? The MTWN holder is compatible with TNMG 1604 indexable inserts; the design of the boring bar supports standard TNMG geometries and common chipbreaker options. What is the shank size and how does it affect rigidity? The shank Ø 32 mm of the S32T MTQNR provides increased stiffness compared with smaller holders, which improves cutting stability and surface finish when machining external profiles. Which cutting direction is this tool intended for? This boring bar is configured for right‑hand cutting, optimised for conventional turning directions on standard CNC lathes. What reach does the tool provide for deep cuts? With a 300 mm overall length, the tool offers extended reach for deeper external turning while maintaining a balance between overhang and rigidity. How does the 107.5° cutting angle influence performance? The 107.5° angle offers a compromise between clearance and edge strength, helping to maintain stable cutting forces and prolong insert life during mixed roughing and finishing operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, precision‑focused milling solution that combines a 100° cutting angle, a 40 mm diameter and a secure 16 mm shank for stable set‑ups; the result is efficient face‑milling with minimal tool change time. Order via Metav Werkzeuge for reliable supply from Emmerich or request consultation if technical matching is required. Planing cutter head for BLMP 0904 indexable inserts — 100° cutting angle, 40 mm diameter (Teknik Makina) The planing cutter head is a compact face‑milling head designed for BLMP 0904 indexable inserts and engineered for precise steel machining in workshop and production environments 100° cutting angle for fine finishing 40 mm diameter for compact setups 16 mm shank for secure mounting Compatible with BLMP 0904 inserts (Taegutec) Proven cutting geometry for consistent surface quality The head’s 100° cutting angle and its arrangement of five cutting edges deliver a balanced material engagement that reduces vibration and produces a consistent finish on machined faces. The geometry is optimised for finishing passes and light to medium material removal, so cycle times can be shortened without compromising surface integrity. For users seeking measurable efficiency gains, this results in fewer re‑works and a steadier production flow when machining steels. Secure mounting and quick insert change to reduce downtime With a 16 mm shank and a compact 40 mm diameter, the tool head fits tight toolholders while keeping the centre of gravity close to the spindle, improving rigidity during face‑milling. Insert clamping is secured by a Torx screw M3.5x8.5 operated with a T10 key, enabling straightforward, repeatable insert replacement. The use of standard BLMP 0904 indexable inserts (Taegutec) simplifies stock management and ensures rapid return to cut after a tool change, supporting uninterrupted production. Built for workshop robustness and predictable handling Constructed for demanding steel applications, the component’s modest mass (approx. 0.176 kg) and compact overall length of 40 mm make it easy to handle and fit into crowded fixturing without compromising stability. The combination of compact design and durable construction provides a practical balance between handling convenience and machining performance, which is particularly valuable for small‑batch production and mixed‑operation job shops where tool flexibility and reliable repeatability matter. Contact Metav Werkzeuge for tailored advice and assured availability from Emmerich — quote SKU T485TM for prompt assistance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: T485TM Manufacturer: Teknik Makina Product: Planing cutter head for BLMP 0904 indexable inserts Facts Diameter: 40 mm Overall length: 40 mm Shank diameter: 16 mm Cutting angle: 100° Cutting edges: 5 Weight: 0.176 kg Torx screw: M3.5x8.5 Torx key size: T10 Special features Compatible with BLMP 0904 indexable inserts Suitable for Taegutec inserts Designed for face‑milling applications Robust construction for steel machining FAQ Which indexable inserts fit this tool head? The planing cutter head accepts BLMP 0904 indexable inserts; compatibility with Taegutec inserts is specified for the Teknik Makina face‑milling head (SKU T485TM). What is the required shank and tightening method? The head uses a 16 mm shank and is secured with a Torx screw M3.5x8.5, tightened/loosened using a T10 Torx key for repeatable clamping. How many cutting edges does the tool provide and what finish can be expected? The tool incorporates five cutting edges and a 100° cutting angle, delivering a stable engagement for fine finishing on machined faces. Is this head suitable for steel machining? Yes; the Teknik Makina planing cutter head is designed for robust steel machining, offering the geometry and construction needed for routine face‑milling tasks. How are inserts replaced on the face‑milling head? Replace inserts by loosening the Torx screw (M3.5x8.5) with a T10 key, remove the used BLMP 0904 insert and fit the new insert; ensure seating and secure clamping before resuming machining operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 100° cutting geometry, proven compatibility with BLMP 0603 indexable inserts and a compact 16 mm shank to increase face-milling throughput while reducing set-up time; order directly via Metav Werkzeuge or consult our specialists for application advice and integration support. Planmesserkopf — Face milling head, 100° cutting angle, for BLMP 0603 (Teknik Makina) The Planmesserkopf is a compact face milling head designed for use with BLMP 0603 indexable inserts, offering controlled chip formation and consistent surface quality across a range of facing and finishing tasks 100° cutting geometry for stable cuts Compatible with BLMP 0603 indexable inserts Compact 16 mm shank for versatile mounting Secure Torx clamping with M3x6.5 screw Stable, efficient facing with optimised geometry The 100° cutting geometry delivers reduced vibration and predictable chip flow, which directly improves surface finish and cycle-to-cycle repeatability. By pairing the head with BLMP 0603 inserts, the cutter benefits from small, indexable cutting edges that spread wear and extend tool life. For production environments that value uptime, this translates into fewer stoppages for regrinding and a lower cost per component through consistent material removal rates and predictable tool-change intervals. The result is measurable productivity gain without complex process changes. Fast, accurate mounting and reliable clamping A precise 16 mm shank and compact overall length minimise overhang and contribute to rigidity in the spindle, supporting higher feed rates and better dimensional control. The tool is delivered with a M3x6.5 Torx screw and requires a T8 key for insert clamping, enabling quick insert replacement and secure seating. The combination of a small form factor and robust fastening reduces set-up time and minimises human error during tool changes, which is particularly valuable in mixed-batch and job-shop workflows where changeovers must be efficient and repeatable. Compact design engineered for workshop durability With a nominal 40 mm diameter, 6 cutting edges and a lightweight construction of approximately 0.262 kg, the head offers a balance between strength and manoeuvrability. The compact mass lowers spindle load while maintaining cutting stability, making the component suitable for both high-speed finishing and conventional facing operations. Manufactured with attention to metalworking tolerances, the cutter head resists deformation and keeps insert seats intact over many tool cycles, supporting long-term reliability and predictable maintenance intervals. Clear application focus for improved throughput Designed for indexable inserts and compatible with Taegutec blades, the head is ideal for facing, light roughing and finishing on castings, steel and general workshop materials where small insert sizes are preferred. The small insert format reduces per-insert cost while allowing multiple indexes per blade, enabling a favourable balance between initial tooling investment and ongoing operating cost. When integrated into a production cell, the head’s features contribute to shorter machining cycles and a streamlined tooling inventory. For procurement, technical matching or rapid delivery advice on Teknik Makina’s face milling head (SKU T480TM), contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for tailored selection and reliable supply from stock. Technical data SKU: T480TM Manufacturer: Teknik Makina ECLASS: 21180902 Facts Diameter: 40 mm Shank (arbor) diameter: 16 mm Weight: 0.262 kg Total length: 45 mm Cutting angle: 100° Cutting edges: 6 Torx screw: M3x6.5 Torx key: T8 Special features for BLMP 0603 Indexable Inserts Compatible with Taegutec inserts Compact face milling head design Suitable for facing and finishing operations FAQ What insert type does this milling head use? The milling head is configured for BLMP 0603 indexable inserts; Teknik Makina’s Planmesserkopf is optimised for the small-format BLMP 0603 geometry. Is the head compatible with Taegutec inserts? Yes, the component is specified as compatible with Taegutec inserts and seats BLMP 0603 blades correctly for secure clamping and repeatable performance. What are the mounting dimensions for spindle selection? The head has a 16 mm shank diameter and a total length of 45 mm, which supports compact mounting and low overhang in many milling spindles. How many cutting edges are available per head? The design provides 6 cutting edges, enabling multiple indexes and a favourable balance between cutting area and insert replacement frequency. Which applications benefit most from this head? The head is best for facing, light roughing and finishing where BLMP 0603 inserts offer efficient chip control and low per-insert cost; it suits both CNC and manual milling environments. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, precision-engineered solution that combines durable performance and fast insert changes; the design balances rigidity with easy handling and is ideal for demanding turning operations. Order directly via Metav Werkzeuge or request tailored advice from our consultants for application-specific recommendations. Angle tool head T222TM — 90° indexable insert tool holder for LNMT 0804 inserts The Angle tool head T222TM is designed for 90° turning operations using LNMT 0804 indexable inserts and is optimised for robust workshop and production use. 90° cutting geometry for square shoulders Compatible with LNMT 0804 inserts from ISCAR 16 mm shank diameter for compact setups Quick securement via M2.5x7 Torx screw Consistent 90° geometry for reliable shoulder turning The 90° cutting geometry ensures repeatable, right-angled faces while reducing setup adjustments, making it particularly suited to operations that demand tight tolerances. The holder’s design accepts LNMT 0804 indexable inserts, which enable quick insert change and consistent chip control. With a 16 mm shank and a compact Ø40 mm head, the unit delivers a rigid connection to the toolpost, reducing vibration and improving surface finish in serial turning tasks. This results in fewer reworks and more predictable cycle times on production lines. Easy, secure clamping and simple maintenance Clamping is performed with an M2.5x7 Torx screw tightened using a T8 Torx key, a straightforward routine that keeps tool changeover times low and maintenance predictable. The connection system is engineered to retain the insert precisely, preventing micro-movement that can compromise tool life. The head’s measured overall length 40 mm and modest weight of 0.24 kg make the holder easy to position and handle during tool setup, while the robust fastening minimises the need for frequent readjustment. Designed for durable performance in metalworking Built for demanding machining, the tool head supports high-grade steel machining and is intended to deliver long tool life under steady cutting conditions. The configuration accommodates up to six cutting edges in its operational concept, enabling efficient use of inserts and dependable performance across repetitive cuts. The compact footprint and sturdy construction help maintain cutting parameters and contribute to predictable dimensional outcomes, which is essential in batch production and contract machining environments. Practical benefits for production workflows Integrating this holder into a tooling system simplifies inventory by standardising on the LNMT 0804 insert family and ISCAR-compatible geometries. The combination of a compact shank, secure clamping, and 90° geometry supports faster cycle-to-cycle consistency and reduces downtime associated with complex tool changes. These rational advantages translate into economic gains through improved throughput and lower scrap rates, making the component a pragmatic choice for workshops and manufacturing facilities aiming for operational reliability. For application guidance, stock availability or to arrange a purchase through Metav Werkzeuge, contact our team in Emmerich — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com — Metav’s consultants will assist with compatibility and selection advice Technical Data Article number: T222TM Product: Angle tool head for LNMT 0804 indexable inserts Manufacturer: Teknik Makina Key dimensions Shank diameter (mm): 16 Head diameter (mm): 40 Overall length (mm): 40 Weight (kg): 0.24 Cutting geometry: 90° Cutting edges: 6 Special features Compatible with LNMT 0804 indexable inserts Suitable for ISCAR insert types Fastening: M2.5x7 Torx screw Torx key size required: T8 FAQ Is this tool head compatible with ISCAR inserts? Yes. The angle tool head is compatible with LNMT 0804 indexable inserts and is specified to work with ISCAR insert types for straightforward integration. What is the shank size and will it fit standard toolposts? The holder has a 16 mm shank diameter; this size suits compact toolpost setups and is common in small to medium turning applications. How is the insert secured in the holder? Insert retention is via an M2.5x7 Torx screw; the screw is tightened using a T8 Torx key to ensure a secure, vibration-resistant fit. Can the head be used for heavy steel turning? The design supports high-grade steel machining and is intended for robust performance with good tool life when used within recommended cutting parameters. What is the SKU and manufacturer for ordering? The SKU is T222TM and the product is supplied by Teknik Makina; orders and technical enquiries can be placed through Metav Werkzeuge for European distribution. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com