Gibt es einen Hahn und Kolb Online Shop?

Take advantage of the combination of robust compatibility with APKT 1604 inserts, stable shank design and efficient chip evacuation for reliable milling performance. Order directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. Shank milling cutter S274TM — for APKT 1604 indexable inserts, Ø 40 mm Shank milling cutter S274TM is an indexable-insert tool designed for efficient face and slot milling where quick insert changes and consistent cutting geometry are required Compatible with APKT 1604 indexable inserts Ø 40 mm cutting diameter for medium-duty milling Shank Ø 32 mm for secure toolholding Four cutting edges with 90° cutting angle Consistent cutter geometry for predictable results The tool offers a stable cutting geometry that supports repeatable machining cycles and predictable surface quality. With a Ø 40 mm cutter body and four cutting edges, the design reduces vibration and evens out tool load, which helps to maintain dimensional accuracy on serial parts. The use of indexable inserts provides quick restoration of cutting performance: a worn edge is replaced faster than regrinding, which shortens machine downtime and contributes to a more economical production rhythm. Secure mounting and simple maintenance for workshop uptime A shank Ø 32 mm ensures firm clamping in standard toolholders and contributes to repeatable concentricity in multi-spindle setups. The tool is supplied for use with APKT 1604 inserts and includes standard fixing elements (Torx screw M4x10, Torx key T15) for straightforward insert changes. The practical assembly reduces set-up time and lowers the risk of assembly errors, so cycle starts are faster and maintenance remains low-effort — a clear advantage for busy fabrication environments. Broad application range and material compatibility Designed as a versatile milling solution, the cutter is suitable for typical industrial machining tasks where indexable inserts are preferred. The four-flute arrangement and 90° cutting angle allow efficient slotting and face milling operations while balancing cutting forces. Compatibility with Korloy APKT 1604 inserts opens access to a wide range of grades for different materials and cutting conditions, enabling adaptation to productivity or finish-focused requirements without changing the tool body. Contact Metav Werkzeuge today for expert guidance from Emmerich on deploying the Teknik Makina S274TM in production — our consultants can verify insert choices, clamping suitability and delivery options to match specific machining needs Technical data Article number: S274TM Manufacturer: Teknik Cutting Tools Product: Shank milling cutter For: APKT 1604 Indexable Inserts Compatible inserts manufacturer: Korloy Torx screw: M4x10 Torx key: T15 Facts Diameter: 40 mm Shank diameter: 32 mm Cutting length: 55 mm Overall length: 150 mm Cutting edges: 4 Weight: 0.96 kg Cutting angle: 90° Special features Suitable for APKT 1604 indexable inserts Compatible with Korloy inserts SKU S274TM — Teknik Makina FAQ Which insert type fits this cutter? The S274TM shank milling cutter is designed for APKT 1604 indexable inserts and is compatible with Korloy-manufactured inserts in that format. What are the key dimensions to check for toolholder compatibility? Check the shank diameter (32 mm) and the overall length (150 mm) to ensure secure clamping and sufficient reach for the intended operation. How many cutting edges does the tool have and what is their arrangement? The cutter features four cutting edges arranged for stable cutting forces and a 90° engagement geometry suited to face and slot milling. Which fastening parts are supplied for insert mounting? The tool requires a Torx fixing screw M4x10 and a T15 Torx key for insert clamping; these are the specified sizes for secure assembly. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust 32 mm shank and a 40 mm cutting diameter combined with four cutting edges for reliable material removal and consistent surface quality; the compact 120 mm overall length keeps tool overhang low for added stability. Order the tool directly via Metav Werkzeuge or consult the technical team for application-specific advice. Indexable insert milling cutter S584TM — 40 mm diameter, 32 mm shank | Teknik Makina The Indexable insert milling cutter S584TM is an indexable-insert tool holder designed to accept BDMT 1704 inserts for versatile face and shoulder milling in machining centres and milling stations. Indexable holder for BDMT 1704 inserts 40 mm cutting diameter, 4 cutting edges 32 mm shank for stable clamping Torx M4x10 fastening, T15 key Predictable performance through geometry and capacity The holder's geometry is tailored for steady metal removal: a 40 mm cutting diameter and 4 cutting edges yield a balanced cut profile that reduces vibration and spreads wear across multiple edges. The tool's 90° cutting angle provides a true shoulder face and consistent corner quality, which is particularly useful when alternating between roughing and finishing passes. These measurable characteristics enable higher feed rates and reproducible results, which helps to shorten cycle times and improve throughput in production environments. The design supports straightforward calculation of cutting data, so set-up times can be reduced and process windows tightened. Fast changeovers and compatible insert system The clamping system uses an M4x10 Torx screw driven with a T15 key for secure and repeatable insert fastening. It is specified for BDMT 1704 indexable inserts and is compatible with inserts from Kyocera, allowing workshops to use proven grades for specific materials. Since insert grades determine cutting performance, the holder itself provides the stable interface while cutting behaviour is adapted by choosing the right insert geometry and coating. The S584TM therefore enables flexible material coverage with minimal downtime for retooling, as insert replacement requires only simple, standardised tools. Workshop handling, balance and lifecycle benefits With an overall length of 120 mm, a cutting length of 40 mm and a compact 32 mm shank, the tool minimises overhang without compromising reach — a balance that reduces deflection and tool wear. The moderate mass (approx. 0.79 kg) assists in maintaining spindle balance during medium-duty milling, while the shank diameter supports secure clamping in standard holders. Practical features such as standard Torx fastening simplify maintenance and spare-part stocking. Choosing a robust holder like this contributes to longer intervals between balancing and reconditioning, which lowers total machining costs and keeps production running smoothly. Contact Metav Werkzeuge for tailored tool recommendations, availability and application support — Metav Werkzeuge’s team in Emmerich can advise on insert grades and clamping strategies via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: S584TM Manufacturer: Teknik Makina Brand: Teknik Cutting Tools SKU: S584TM ECLASS: 21180806 ETIM: EC011860 Facts Cutting diameter: 40 mm Shank diameter: 32 mm Cutting length: 40 mm Overall length: 120 mm Number of cutting edges: 4 Weight: 0.79 kg Cutting angle: 90° Special features For BDMT 1704 indexable inserts Compatible with Kyocera inserts Torx screw fastening M4x10 Torx key size T15 Indexable insert holder design FAQ What inserts fit this tool? The holder is designed for BDMT 1704 indexable inserts; compatible inserts from Kyocera can be used to suit the machining task. Which screw and key are required to secure inserts? Inserts are fastened with an M4x10 Torx screw using a T15 key for repeatable clamping. What are the key dimensions to check for machine compatibility? Relevant dimensions: 32 mm shank diameter, 40 mm cutting diameter, 120 mm overall length and 40 mm cutting length — confirm spindle or toolholder clearance accordingly. Is the tool suitable for finishing operations? Yes; with appropriate insert selection the toolholder supports finishing as well as roughing, thanks to its 90° cutting angle and balanced multi-edge configuration. How does the holder affect tool change and spare parts inventory? Standard Torx fastening and a common insert form (BDMT 1704) mean faster changeovers and simpler stocking of replacement screws and inserts for efficient workshop logistics. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid shank design and targeted cooling to maintain steady cutting performance across long production runs; the combination of a 40 mm cutting diameter, internal coolant and compatibility with BDMT 1704 indexable inserts keeps setup times low and productivity high. Order the cutter directly via Metav Werkzeuge or request tailored advice from the consultants in Emmerich. Shank milling cutter S584-1TM — 40 mm diameter, internal coolant (Teknik Makina) The Shank milling cutter S584-1TM is a robust insert cutter engineered for face and shoulder milling with BDMT 1704 indexable inserts, offering stable metal removal and short changeover times. 40 mm cutting diameter for stable milling Internal coolant for improved chip evacuation Compatible with BDMT 1704 inserts by Kyocera 32 mm shank with solid clamping stability Reliable performance for demanding milling operations The combination of a 40 mm cutting diameter and 4 cutting edges delivers a balance between material removal rate and surface quality. The 32 mm shank increases stiffness in the holder, reducing chatter and enabling higher feed rates with consistent results. For production environments this means fewer rejected parts and steadier cycle times; operators benefit from predictable tool behaviour and maintenance schedules, while planners gain measurable improvements in throughput and process stability. Efficient cooling and chip control for extended tool life Built-in internal coolant directs fluid to the cutting zone, flushing chips away from the inserts and reducing thermal stress on the cutting edges. This targeted cooling improves tool life and supports better surface finish on aluminium, steel and mixed-material workpieces when matched with suitable inserts. The internal coolant path also lowers the risk of chip re-cutting and abrasive wear, which contributes to longer intervals between indexings and lower total tooling consumption over a batch run. Compatibility and straightforward maintenance for minimal downtime Accepted inserts are BDMT 1704, and the cutter is compatible with inserts from Kyocera, enabling use of widely available grades for roughing and finishing. Fast insert changes are facilitated by the T15 Torx drive and M4x10 screws, which are standard in most maintenance toolkits. With an overall length of 120 mm and a cutting length of 40 mm, the tool offers a compact footprint while maintaining reach for shoulder operations. The modest mass of 0.791 kg simplifies handling and reduces toolholder imbalance when correctly clamped. Practical workshop advantages and suitable applications As an indexable shank cutter, the tool is suited to face milling, light shoulder milling and contouring operations where productivity and repeatability matter. The modular design reduces per-part tooling cost because only the inserts are replaced during wear cycles. For procurement and stock management, Metav’s European logistics base in Emmerich provides a near-market supply channel and quality filtering, which supports reliable reordering and consistent product specification across the workshop. Contact Metav Werkzeuge for specification guidance on the Teknik Makina S584-1TM shank milling cutter and to confirm the ideal insert grade and coolant setup for specific applications; Metav’s consultants can advise on delivery from Emmerich and parts availability Technical data Article number: S584-1TM Type: Shank milling cutter Brand: Teknik Makina Description: for BDMT 1704 Indexable Inserts Label: 40mm shank cutter BDMT 1704 L120mm with internal coolant Facts Cutting diameter: 40 mm Overall length: 120 mm Shank diameter: 32 mm Cutting length (shank): 40 mm Number of cutting edges: 4 Weight: 0.791 kg Torx key: T15 Torx screw: M4x10 eCl@ss: 21180806 Special features Internal coolant: true Compatible insert type: BDMT 1704 Compatible insert manufacturer: Kyocera Product type: Shank milling cutter SKU: S584-1TM FAQ What inserts are suitable for this cutter? The cutter accepts BDMT 1704 indexable inserts; compatible grades from Kyocera can be used for roughing or finishing depending on the workpiece material and cutting data. Does the tool provide internal coolant? Yes, internal coolant is integrated to deliver coolant directly to the cutting zone, improving chip evacuation and prolonging insert life. What are the key dimensions for clamping and setup? Clamping requires a 32 mm shank holder and the cutter has an overall length of 120 mm with a 40 mm cutting diameter, as stated in the technical data. Which drive and screws are required for insert changes? Insert retention uses a T15 Torx drive and M4x10 screws, enabling straightforward replacement with standard workshop tools. Is the cutter suitable for fine finishing? When equipped with an appropriate finishing grade insert, the cutter supports fine finishing operations and improved surface quality due to coolant-assisted cutting. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Comprehensive Technical Specifications: Order Number: S801TM Item: End Mill usable with WNMX 1305 Indexable Inserts the Hersteller's Korloy Brand: Teknik Makina Structural Details: Diameter: 40mm Cutting Edges: 3 Total length: 150mm Diameter Connection: 32mm Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Benefit from a reliable combination of a 40 mm cutting diameter, internal coolant and compatibility with LNMX 1004 indexable inserts for stable chip evacuation and extended tool life. Order the shank milling cutter directly via Metav Werkzeuge or contact our technical advisers for application support. Shaft milling cutter S097TM – 40 mm diameter, internal coolant (Teknik Makina) Shaft milling cutter S097TM is an indexable shank cutter designed for efficient face and shoulder milling with LNMX 1004 indexable inserts in general machining applications. 40 mm cutting diameter for robust machining Internal coolant for improved chip evacuation Compatible with LNMX 1004 indexable inserts Hex Torx T15 screw system M4x10 Heavy‑duty cutting capacity for consistent performance The tool was developed for demanding milling tasks where stability and repeatability matter. With a 40 mm diameter, 5 cutting edges and a 200 mm total length, the cutter provides a balance between material removal rate and rigidity. The 32 mm shank ensures secure clamping in standard toolholders, reducing vibration and improving surface finish. These mechanical characteristics translate into fewer interruptions for tool correction and a steadier production flow, making the miller suitable for workshop and small‑scale industrial environments. Controlled cooling and secure insert clamping for longer tool life Built‑in internal coolant directs fluid close to the cutting zone to lower temperatures and support chip evacuation, which helps to maintain cutting geometry and prolong insert life. The tool is designed for LNMX 1004 indexable inserts, with a secure Torx fastening system using Torx T15 and M4x10 screws to ensure consistent seating and rapid indexable‑insert changes. Proper coolant routing and reliable clamping reduce thermal cycling and wear, delivering improved process stability and more predictable maintenance intervals. Easy integration and efficiency gains on the shop floor The miller's dimensional design and moderate weight (approx. 1.2 kg) simplify handling while offering the robustness required for repeated operations. Identified under SKU S097TM, the cutter is optimised for quick retrofit into existing tool setups and straightforward insert replacement, which shortens downtime during tool changes. The combination of a rigid 32 mm shank and compact cutting length of 40 mm promotes accurate contouring and consistent results across batches, supporting efficient machining sequences and better use of production capacity. For a tailored recommendation based on Teknik Cutting Tools' internal‑coolant design, contact Metav Werkzeuge to discuss the S097TM shank milling cutter and application compatibility: info@metav-werkzeuge.com | +49 2822 7131930 Key data Article number: S097TM Label: 40mm shank cutter LNMX 1004 L200mm with internal coolant Product type: Shaft milling cutter Manufacturer: Teknik Makina Measurements & core data Cutting diameter: 40 mm Total length: 200 mm Shank diameter: 32 mm Cutting length: 40 mm Number of cutting edges: 5 Weight: 1.2 kg Features & compatibility Internal coolant Compatible with LNMX 1004 indexable inserts Compatible inserts manufacturer: Korloy Torx key: T15 Torx screw: M4x10 FAQ Which indexable inserts fit this shank milling cutter? The cutter is designed for LNMX 1004 indexable inserts; compatible inserts from Korloy are recommended for best fit and performance with the S097TM shank milling cutter. Does the tool provide internal coolant? Yes, the S097TM features internal coolant supply to the cutting zone to support chip evacuation and thermal control during milling. What Torx key and screw are required for insert changes? Insert clamping uses a Torx T15 key and M4x10 screws, ensuring secure and repeatable fastening of LNMX 1004 inserts. What are the key dimensions to consider for toolholder compatibility? Important dimensions are a 32 mm shank diameter, 40 mm cutting diameter and 200 mm total length; these values help to verify holder fit and reach for the required operation. Is the S097TM suitable for quick replacement in production? The cutter is engineered for straightforward insert changes and stable clamping, supporting efficient swap‑outs and shorter machine downtime during maintenance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust cutting capacity, reliable internal coolant and precise insert clamping for continuous, cost-efficient milling operations; order the shaft milling cutter directly via Metav Werkzeuge or ask our consultants if technical advice is required. Shaft milling cutter for XEKT 1904 Indexable Inserts — Teknik Makina (40 mm, internal coolant) The shaft milling cutter for XEKT 1904 Indexable Inserts is designed for insert-based milling tasks in production and workshop environments, offering stable cutting performance with integrated coolant supply. 40 mm diameter for robust material removal Internal coolant for improved tool life Compatible with XEKT 1904 inserts (Korloy) High-capacity cutting with precise geometry This insert-based cutter combines a compact head with a generous 40 mm cutting diameter and three cutting edges, delivering balanced chip loads and consistent surface results. The 32 mm shank and a 160 mm overall length provide the necessary stability for interrupted cuts and shoulder milling, while the defined cutting length of 61 mm ensures an efficient engagement zone. Such geometry reduces vibration and enables predictable tool behaviour, which supports higher first-pass yields and lowers rework rates. Coolant-fed design that prolongs service life The integrated internal coolant supply channels coolant directly to the insert rims, which improves heat control at the cutting zone and enhances chip evacuation. Better thermal management reduces edge wear and helps preserve cutting geometry over longer cycles, translating into fewer index changes and reduced production interruptions. For insert systems this means a lower cost per component processed and a more reliable tool life profile in continuous shifts. Secure clamping and proven insert compatibility Designed for XEKT 1904 indexable inserts, compatible with Korloy supply, the cutter uses a secure clamp system tightened with a T15 Torx key and M4x8.5 screws for repeatable seating. The replaceable-insert concept facilitates rapid maintenance: worn inserts can be exchanged within minutes, restoring cutting performance without the need to replace the entire tool body. This serviceability supports efficient shop-floor logistics and helps maintain steady cycle times. Integration into workshop set-ups and practical handling With a mass of 0.955 kg, the tool balances rigidity and manageable handling for tool changes and set-up. The 32 mm shank fits holders and adaptors engineered for standard tool-holding systems, so the cutter can be integrated into milling spindles designed for insert tooling. The combination of robust design, clear mechanical interfaces and internal coolant makes this cutter suitable for production environments seeking stable, repeatable milling performance. For secure, insert-based milling with internal coolant, contact Metav Werkzeuge to procure the Teknik Makina S389TM shaft milling cutter or request tailored technical advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: S389TM Product: Shaft milling cutter for XEKT 1904 indexable inserts Manufacturer: Teknik Makina SKU: S389TM UID: S389TM Measurements Diameter: 40 mm Overall length: 160 mm Cutting length: 61 mm Shank diameter: 32 mm Weight: 0.955 kg Number of cutting edges: 3 Torx key: T15 Screw: M4x8.5 Features Internal coolant Indexable insert system: XEKT 1904 Compatible insert manufacturer: Korloy Secure Torx clamping FAQ Which inserts fit this cutter? The cutter accepts XEKT 1904 indexable inserts; compatible inserts are available from Korloy and other suppliers offering that insert geometry. Is the tool coolant-fed and how does that help? Yes, the tool features internal coolant that directs fluid to the cutting edge, improving heat control, chip evacuation and overall tool life. What key and screws are required for insert clamping? Insert clamping requires a T15 Torx key and M4x8.5 screws for secure and repeatable seating of each XEKT 1904 insert. What shank size is needed for holder compatibility? The tool has a 32 mm shank, so a tool holder accepting a 32 mm diameter shank is required for correct retention and concentricity. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 40 mm cutting diameter, internal coolant and compatibility with Korloy XNKT 0604 indexable inserts for stable production cycles. Order the shank milling cutter directly via Metav Werkzeuge or consult our specialists for precise application advice. Shank milling cutter – 40 mm, internal coolant, for XNKT 0604 inserts (Teknik Makina) Shank milling cutter designed for use with XNKT 0604 indexable inserts, offering coolant-fed performance and a robust Ø32 mm shank for demanding milling tasks Diameter 40 mm for heavy-duty milling Internal coolant for improved tool life Compatible with Korloy XNKT 0604 inserts Shank Ø32 mm, overall length 130 mm Precision fit and secure clamping for repeatable results This cutter body is engineered for a precise fit with Korloy XNKT 0604 indexable inserts, using a five-edge configuration to distribute cutting load evenly and reduce vibration. The design incorporates a Torx fastener system (T8 key, M3x7 screw) to ensure secure clamping and fast insert changes, supporting consistent radial run-out and repeatability. A controlled interface between the insert pocket and the cutter body minimises micro-movements during cutting, which translates into predictable tool life and steady surface quality on workpieces. Coolant-fed design that improves chip control and finish The integrated internal coolant channels direct fluid close to the cutting edge, which helps with chip evacuation, temperature control and lubrication at the contact zone. For operations where chip management and thermal stability matter, the internal feed reduces the risk of built-up edge and improves surface integrity. This coolant-assisted arrangement also supports prolonged insert life and fewer unscheduled tool changes, contributing to greater uptime and lower process cost per component. Robust shank geometry for workshop reliability Built with a 32 mm shank and an overall length of 130 mm, the tool balances rigidity and reach for a wide range of milling set-ups. The cutting head offers a 45 mm effective cutting length and five cutting edges, allowing efficient material removal rates without sacrificing stability. At a mass of 0.865 kg, the assembly is substantial enough for steady cutting while remaining manageable for quick tool exchanges. The result is a cutter suited to repetitive workshop tasks where dependable clamping, easy insert replacement and consistent cutting performance are priorities. For coolant-fed milling solutions by Teknik Makina, contact Metav Werkzeuge in Emmerich for expert advice and procurement: info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: S842-1TM Product type: Shank milling cutter for XNKT 0604 indexable inserts Manufacturer: Teknik Makina Facts Diameter: 40 mm Overall length: 130 mm Shank diameter: 32 mm Cutting length: 45 mm Number of cutting edges: 5 Weight: 0.865 kg Torx key: T8 Torx screw: M3x7 Internal coolant: yes Special features Compatibility: Korloy XNKT 0604 inserts Coolant-fed design Torx fastener clamping system Robust shank geometry for stability FAQ Which inserts fit this cutter? The cutter is designed for XNKT 0604 indexable inserts; Korloy inserts in this grade are stated as compatible with the cutter body (SKU S842-1TM). How does the internal coolant affect performance? Internal coolant channels deliver fluid close to the cutting edge, improving chip evacuation, lowering cutting temperatures and helping to extend insert life when using this coolant-fed milling cutter. What fastening system secures the inserts? Inserts are secured with a Torx screw (M3x7) tightened with a T8 key, providing reliable and repeatable clamping for the five-edge cutter configuration. What are the key dimensions to check for machine compatibility? Check the 32 mm shank diameter and the 130 mm overall length against the machine spindle and toolholder capabilities before mounting the cutter. Is this cutter suitable for heavy-duty milling set-ups? The 40 mm diameter combined with a robust shank and coolant supply makes the tool appropriate for demanding milling operations where stability and chip control are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, purpose-built face milling solution that pairs a 40 mm diameter cutter body with six cutting edges to deliver consistent material removal and stable surface finishes. The 16 mm arbor bore and standard Torx M3x7 fastening ensure rapid insert changes and repeatable clamping; order or request technical advice via Metav Werkzeuge for supply from Emmerich. Planmesserkopf (Face milling head) for LNMX 0603 indexable inserts — 40 mm, 6 cutting edges | Teknik Cutting Tools A face milling head (Planmesserkopf) engineered for efficient face milling with LNMX 0603 indexable inserts in light-to-medium duty applications 40 mm diameter for precise face milling Fits LNMX 0603 indexable inserts Fixed with M3x7 Torx screw and T8 key Six cutting edges for smooth material removal Predictable cutting performance for shorter cycle times The compact cutter body delivers a 40 mm diameter that concentrates cutting forces close to the tool centre, reducing deflection and enabling more predictable cycle times on short to medium overhangs. With six cutting edges, chip load per edge is lowered, which supports a smoother surface finish and extends tool life under comparable cutting parameters. This configuration is especially suited to repetitive facing operations where consistency and repeatability directly affect throughput. Rapid insert changes and reliable clamping reduce downtime A straightforward Torx fastening system—secured by an M3x7 screw and operated with a T8 key—permits quick insert replacement while maintaining stable clamping. The 16 mm arbor bore ensures a secure fit in common holders and minimises vibration when properly mounted. These mechanical features translate into reduced changeover times and lower setup overhead, helping workshops maintain steady production without complex fixture adjustments. Broad compatibility to simplify tooling logistics Designed for LNMX 0603 indexable inserts (insert designation KRLY) and compatible with Korloy inserts, the cutter head uses industry-standard insert geometry so replacement parts are readily available. The straightforward compatibility reduces inventory complexity and supports rapid recovery after wear or breakage. Combined with Metav Werkzeuge’s European supply logistics, this solution supports a dependable tooling strategy for trades and small-scale production environments. For verified compatibility and tailored advice on tooling setups, contact Metav Werkzeuge for prompt supply and technical support from Emmerich: +49 2822 7131930 or info@metav-werkzeuge.com Technical Data SKU: T836TM Item: face milling head (Planmesserkopf) Compatible inserts: LNMX 0603 Compatible insert manufacturer: Korloy Fixing screw: M3x7 Torx key: T8 Core specifications Diameter: 40 mm Overall height: 40 mm Shank / bore: 16 mm Cutting edges: 6 Design & compatibility Insert type: KRLY Fits LNMX 0603 indexable inserts Manufacturer: Teknik Makina SKU reference: T836TM FAQ How are the inserts secured in the face milling head? The face milling head (SKU T836TM) secures LNMX 0603 inserts with an M3x7 Torx screw; a T8 key is used for tightening to ensure repeatable clamping. What arbor or holder size is required for mounting? A 16 mm arbor bore is specified for this cutter body, so a 16 mm holder or adaptor is required for correct seating and stability. Which insert geometries and makers are supported? The cutter accepts LNMX 0603 indexable inserts, commonly available from Korloy; the insert designation for this head is KRLY. Is this head suitable for heavy roughing operations? This design is optimised for face milling and light-to-medium material removal where a 40 mm diameter and six cutting edges provide balanced performance; heavy roughing beyond these parameters should be assessed against machine rigidity and cutting conditions. Are replacement inserts and spare screws standard parts? Replacement LNMX 0603 inserts from Korloy and standard M3x7 Torx screws are widely available, simplifying maintenance and spare-part logistics for workshops using this head. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, high-precision solution that combines a 40 mm diameter, internal coolant and compatibility with XNKU 06T3 indexable inserts to speed up face milling with consistent surface quality; order directly via Metav Werkzeuge or consult our specialists for integration advice. Face milling head — for XNKU 06T3 indexable inserts, 40 mm with internal coolant (Teknik Makina) The Face milling head is a compact cutter head engineered for accurate face milling operations in production and workshop environments, compatible with XNKU 06T3 indexable inserts and designed to integrate with standard toolholders. 40 mm diameter for reliable face milling Internal coolant for efficient chip removal Compatible with XNKU 06T3 indexable inserts Overall length 40 mm, lightweight 0.224 kg High-performance compatibility for predictable machining results The milling head accepts XNKU 06T3 indexable inserts and is optimised for a 90° cutting angle, ensuring a true face finish and predictable material removal. With capacity for five cutting edges, the design minimises tool change frequency while maintaining process stability. The internal coolant channel directs lubricant to the cutting zone, reducing built-up edge and improving chip control; this leads to longer insert life and a more consistent surface finish across batch runs. Technical clarity is provided by measurable parameters such as 40 mm diameter, L40 mm overall length and a 16 mm shank, which support planning and fixture selection in CNC setups. Practical design that reduces downtime and simplifies maintenance The compact construction and modest mass (0.224 kg) favour rapid spindle acceleration and reduced load on the toolholder, while the use of Torx fastening (T8) and standard M2.5x7 screws supports quick serviceability. Replacement of indexable inserts is straightforward thanks to the standardised insert pocket geometry, which allows fast indexing and repeatable seating. The head’s configuration, supplied by Teknik Makina, is compatible with Palbit-specified inserts, enabling streamlined procurement and predictable stocking of spare parts. Clear mechanical connections and standardised fixing elements contribute to lower maintenance time and a cleaner process workflow. Application advantages and procurement confidence for workshops Suited to routine face milling tasks where consistency and uptime matter, the head offers a balance between compactness and capacity for multi-edge inserts. The controlled coolant delivery and robust clamping ensure reduced insert wear under typical production feeds and speeds, helping to lower overall machining costs per component. For procurement, the head is identified by SKU T683TM, making order management and inventory tracking straightforward. Integration into existing toolsets is simplified by the small overall length and the 16 mm mounting interface, supporting efficient tool changeovers and compact tool magazine layout. For reliable face milling with controlled coolant delivery, contact Metav Werkzeuge to discuss specification matching and availability of the Teknik Makina face milling head (SKU T683TM) via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: T683TM Product type: Face milling head (Planmesserkopf) Designation: for XNKU 06T3 indexable inserts Facts Diameter: 40 mm Overall length: 40 mm Shank diameter: 16 mm Weight: 0.224 kg Number of cutting edges: 5 Cutting angle: 90° Special features Internal coolant: yes Compatible insert manufacturer: Palbit Fastening: Torx T8, screw M2.5x7 Manufacturer: Teknik Makina FAQ What inserts fit this milling head? The head is designed for XNKU 06T3 indexable inserts; Palbit inserts matching that designation are compatible. Is internal coolant integrated in the design? Yes, the milling head features internal coolant to direct coolant to the cutting zone for improved chip control. How many inserts or cutting edges does the head accommodate? The cutter head is configured for five cutting edges, which reduces indexing frequency during production. What is the shank size for mounting? The shank diameter is 16 mm, suitable for holders accepting that interface. Which fastening hardware is required for assembly? Assembly uses a Torx T8 key and M2.5x7 screws as supplied in the mounting design. How is the product identified for ordering? Order and inventory reference is SKU T683TM, which simplifies procurement and tracking. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Specifications: Order Number: T672TM Item: Face Mill usable with LNXT 1306 Indexable Inserts the Hersteller's Palbit Brand: Teknik Makina Quantitative Characteristics: Diameter: 40mm Cutting Edges: 4 Weight: 0.225kg Total length: 40mm Diameter Connection: 16mm Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Benefit from coolant-assisted cutting and stable performance delivered by a compact 40 mm face mill; the internal coolant reduces heat and supports consistent chip evacuation while the four-edge configuration keeps cuts balanced. Order the round insert face mill directly via Metav Werkzeuge or ask our consultants if needed. Round insert face mill for RDMT 1204 indexable inserts — 40 mm, internal coolant (Teknik Makina) The Round insert face mill for RDMT 1204 indexable inserts is a compact, coolant-fed cutter designed for precise face milling operations where reliable chip control and quick insert changes are essential. Ø 40 mm diameter Internal coolant feed Compatible with RDMT 1204 inserts Four cutting edges for balanced cutting Coolant-assisted cutting for consistent cycle times The integrated internal coolant feed channels coolant directly to the cutting zone, which lowers cutting temperatures and supports longer tool life. By flushing chips away from the insert pockets the system improves chip evacuation, reducing the risk of recutting and helping to maintain surface finish tolerances in continuous production. With a compact Ø 40 mm body the cutter is particularly suited to tight setups and machines where controlled material removal and repeatability are priorities. Modular clamping and insert handling to reduce downtime Compatibility with RDMT 1204 indexable inserts ensures access to a broad range of grades and geometries for different materials. The tool secures inserts with a Torx clamping screw that matches a T15 key and uses M3.5x8.5 Torx screws, enabling quick, standardised insert changes and straightforward maintenance procedures. The four cutting edges arrangement balances forces during cutting, which reduces vibration and improves surface consistency — a direct benefit for batch production and finishing passes. Compact design and workshop-ready supply chain Weighing just 0.236 kg and with an overall length of 40 mm, this cutter occupies little spindle space while delivering the rigidity expected in industrial environments. The T139-1TM designation simplifies stock handling and reordering, and the robust build from Teknik Makina supports repeatable setup across multiple workstations. For procurement and integration, Metav offers reliable supply and product advice to help fit the cutter into existing tool programmes without disrupting throughput. For dependable coolant-fed face milling with RDMT 1204 inserts, contact Metav Werkzeuge to discuss the Teknik Makina T139-1TM and its application in the production environment; eMail: info@metav-werkzeuge.com or call +49 2822 7131930 to arrange specification support or orders. Technical data SKU: T139-1TM Manufacturer: Teknik Makina Product type: Round insert face mill Label: 40mm Rundplattenfräser RDMT 1204 L40mm mit Innenkühlung UID: T139-1TM Dimensions & core figures Diameter: 40 mm Overall length: 40 mm Weight: 0.236 kg Number of cutting edges: 4 eCl@ss: 21180902 Features & compatibility Compatible with RDMT 1204 indexable inserts Internal coolant feed Torx key: T15 Torx screw: M3.5x8.5 FAQ What inserts does this cutter accept? The round insert face mill accepts RDMT 1204 indexable inserts; the configuration is optimised for those round insert geometries to provide secure seating and efficient cutting. How does the internal coolant benefit machining? Internal coolant in the cutter directs fluid to the cutting edge to reduce temperature, support chip evacuation and contribute to extended insert life for the T139-1TM tool. Which Torx key is required for insert changes? Insert clamping uses a Torx interface compatible with a T15 key and Torx screws sized M3.5x8.5 to ensure standardised, secure tightening. Is this cutter suitable for compact machine tools? Yes; the compact Ø 40 mm diameter and 40 mm overall length make it suitable for limited spindle clearance while maintaining the rigidity needed for stable cuts. How does the four-edge design affect surface finish? The four cutting edges distribute cutting forces evenly, reducing vibration and supporting consistent surface quality across repeated passes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high-performance milling solution that combines precise cutting geometry with easy maintenance: the 40 mm diameter design with three cutting edges ensures efficient material removal while the 16 mm shank provides secure mounting for stable machining. Order the tool directly via Metav Werkzeuge or consult the team for application advice. Round Insert Milling Cutter – 40 mm, for RDMT 12T3 indexable inserts by Teknik Makina The Round Insert Milling Cutter is a compact face milling tool designed for light to medium milling operations using RDMT 12T3 indexable inserts, ideal for workshop and small-batch production where rapid tool changes and consistent chip control are required. Ø 40 mm cutting diameter Three cutting edges for efficient removal Fits RDMT 12T3 indexable inserts 16 mm shank for secure mounting High removal rate with compact geometry The compact cutter achieves a strong balance between size and performance by combining a 40 mm diameter and three cutting edges, which increases the metal removal rate without demanding excessive spindle power. Using indexable inserts such as RDMT 12T3 allows multiple cutting edges per insert; when one edge is worn, the insert can be rotated to present a fresh edge, reducing tool costs and changeover time. This design suits production environments that prioritise cycle-time reduction and predictable throughput. Secure clamping and straightforward serviceability A practical clamping concept simplifies maintenance: the head is secured with a locking screw M3.5 and a Torx screw M3.5x8.5, operated with a T15 Torx key, enabling repeatable torque and safe insert retention. Torx drive engagement minimises cam-out and helps maintain consistent clamping force, which in turn supports stable cutting conditions and longer tool life. Simple, reliable fastenings mean less downtime during insert changes and faster setup for repetitive jobs. Versatile fit for varied machine set-ups With a 16 mm shank and a compact overall length of 40 mm, the cutter is suitable for operations where tool overhang must be kept to a minimum. The lightweight construction (approx. 0.235 kg) reduces centrifugal loads at higher speeds and helps maintain balance in high-rev applications on small milling spindles. Although compact, the tool is engineered for repeatable accuracy in small-batch or job-shop environments and integrates easily into standard toolholders and automated change systems. Discuss application-specific parameters with Metav Werkzeuge to confirm compatibility and optimise machining parameters for Teknik Cutting Tools' T280TM round insert milling cutter; Metav supplies from Emmerich with expert advice and reliable delivery. Technical Data Article number: T280TM Brand: Teknik Makina Model designation: Round insert milling cutter for RDMT 12T3 indexable inserts eClass / ETIM: 21180902 / EC011860 Data Diameter: 40 mm Cutting edges: 3 Overall length: 40 mm Shank diameter: 16 mm Weight: 0.235 kg Special features For RDMT 12T3 indexable inserts Locking screw: M3.5 Torx screw: M3.5x8.5 Torx key size: T15 SKU: T280TM FAQ What inserts are compatible with this cutter? The cutter is designed to accept RDMT 12T3 indexable inserts; using the specified insert form ensures the correct seating and chip control for this tool. How is the insert secured in the cutter? Inserts are clamped with a locking screw M3.5 and retained by the Torx fastener M3.5x8.5, tightened using a T15 key to achieve secure and repeatable retention for the T280TM. Can this cutter be used on small machine spindles? Yes, the combination of a 16 mm shank and compact overall length 40 mm makes the T280TM suitable for machines with limited tool overhang and smaller spindle capacities. How many cutting edges does the tool provide before insert rotation is required? The cutter is built for three cutting edges per revolution; each RDMT 12T3 insert offers multiple usable edges, which can be indexed to extend service life. Is the T280TM available with replacement screws or spare keys? Replacement fasteners compatible with the T280TM are standard Torx types; ensure use of the specified M3.5x8.5 Torx screw and T15 key to maintain clamping reliability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Compact milling performance with Ø40 mm diameter, five cutting edges and a 16 mm shank for secure mounting; delivers efficient material removal and reduced changeover time. Order the Round insert milling cutter directly via Metav Werkzeuge or ask our consultants if needed. Round insert milling cutter T706TM — for RPMW 10T3 indexable inserts, Ø40 mm (Teknik Makina) A versatile Round insert milling cutter T706TM intended for light facing and shoulder milling operations with RPMW 10T3 indexable inserts, designed for compact toolholders and short overhangs. Ø40 mm cutting diameter Compatible with RPMW 10T3 inserts 16 mm shank for compact toolholders Five cutting edges for efficient material removal Performance that keeps production moving The cutter is engineered to increase throughput by combining a compact geometry with five cutting edges that distribute cutting forces and extend tool life. With a Ø40 mm cutting diameter the tool achieves high material removal rates in interrupted and continuous cuts alike, reducing cycle time on small-to-medium batch runs. The design helps maintain consistent chip evacuation, which contributes to cleaner surfaces and less rework over extended production periods. Compatibility that reduces setup time Compatibility with RPMW 10T3 inserts from Korloy makes the tool easy to integrate into existing tooling systems; standardised insert sizes simplify stock management and replacement. Insert clamping uses a Torx screw (M3.5x8.5) operated with a Torx T15 key for straightforward, repeatable retention. The standardized fixing speeds insert changes and lowers fixture downtime, supporting predictable production planning and faster tool change routines. Compact design for confined toolholders A 16 mm shank and a 40 mm overall height make the head suitable for machines with restricted clearance, enabling closer approach to fixtures and fewer collisions on complex parts. The compact footprint optimises tool stiffness when mounted in short overhang, improving dimensional control and surface finish. This arrangement is particularly beneficial in small machining centres and turning/milling hybrids where space and rigidity are both at a premium. Practical applications and operator advantages Designed primarily for general-purpose milling tasks, the cutter is well suited to shoulder milling, light face milling and finishing passes where indexable inserts provide repeatable edge geometry. Use of indexable inserts reduces downtime since worn edges can be rotated or replaced quickly, yielding reduced downtime and stable process quality. The simple Torx clamping system also supports consistent torque application, which helps maintain cutting performance and repeatability across shifts. For technical advice, stock checks or an application review of the Teknik Cutting Tools T706TM, request a supply check or application consultation from Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T706TM Manufacturer: Teknik Makina Compatible inserts: RPMW 10T3 (Korloy) Shank diameter: 16 mm Cutting diameter: 40 mm Total height: 40 mm Cutting edges: 5 Clamping screw: M3.5x8.5 Torx key size: T15 Facts Diameter: 40 mm Total height: 40 mm Shank diameter: 16 mm Cutting edges: 5 Screw: M3.5x8.5 Special features Suitable for RPMW 10T3 indexable inserts Compatible with Korloy inserts Torx clamping system Compact design for confined toolholders SKU: T706TM FAQ What insert type fits this cutter? The cutter accepts RPMW 10T3 indexable inserts; it is specified for those insert dimensions and is compatible with Korloy RPMW 10T3 grades. How is an insert secured in the cutter? Inserts are clamped with a screw (M3.5x8.5) that is tightened using a Torx T15 key, providing consistent and repeatable clamping for the T706TM. Which machines benefit most from this cutter? The compact geometry and 16 mm shank make the tool particularly suitable for small machining centres and applications with limited clearance where stiffness and short overhangs are required. Does the tool support quick changeover on production lines? Yes, the use of standard RPMW 10T3 indexable inserts and a Torx clamping system reduces changeover time and simplifies insert stock management for continuous production. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Taking advantage of the 40 mm diameter, internal coolant and compatibility with WNMX 09T3 indexable inserts delivers a compact, high-efficiency solution for face milling operations; order via Metav Werkzeuge or consult their technical team for application support. Face milling head for WNMX 09T3 indexable inserts — 40 mm, internal coolant (Teknik Makina) Face milling head designed for efficient face milling with WNMX 09T3 indexable inserts in general workshop and industrial applications 40 mm diameter for compact machining Internal coolant for improved tool life Four cutting edges for smooth surface finish Compatible with Korloy WNMX 09T3 inserts Consistent machining performance for repetitive tasks This cutter head offers a reliable balance between rigidity and accessibility. The 40 mm diameter and lightweight construction deliver steady engagement at typical spindle speeds, reducing vibration during face milling. Designed for WNMX 09T3 indexable inserts, the unit supports repeatable results on cast iron, steel and non-ferrous materials when paired with the appropriate insert grades. The presence of four cutting edges also spreads cutting forces evenly, which helps preserve spindle bearings and maintain consistent cycle times. Built-in coolant and robust fastening for longer tool life Integrated internal coolant channels provide directed lubrication and chip evacuation at the cutting zone, lowering thermal load on the inserts and minimising built-up edge. The secure clamping system with M3x7 Torx screws (Torx key T8) simplifies insert changes while ensuring repeatable seating. These characteristics combine to reduce downtime and extend insert life, translating into measurable improvements in process economy and fewer tool changes per production shift. Workshop-ready design for straightforward integration The head’s compact overall length and compatibility with Korloy WNMX 09T3 inserts make it straightforward to adopt in existing tool setups. The lightweight construction eases handling during tool preparation and the standardised screw fixation supports quick maintenance routines. For operations aiming to centralise suppliers, the component fits neatly into broader tooling strategies, enabling a smooth transition to higher productivity without complex retrofitting. Discuss specific application requirements with Metav Werkzeuge to match this Teknik Makina face milling head to production needs — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: T669-1TM Label: 40mm face milling head WNMX 09T3 L40mm with internal coolant ECLASS: 21181015 Facts Diameter: 40 mm Overall length: 40 mm Weight: 0.213 kg Cutting edges: 4 Special features Internal coolant Compatible with WNMX 09T3 indexable inserts (Korloy) Torx screw M3x7, Torx key T8 Manufacturer: Teknik Makina FAQ What inserts fit this milling head? The milling head is compatible with WNMX 09T3 indexable inserts; Korloy grades are specified for straightforward matches. Does the head provide coolant to the insert tip? Yes, internal coolant channels supply lubrication directly to the cutting zone to aid chip evacuation and reduce thermal load. How many cutting edges are active on this head? The component is configured with four cutting edges, which helps distribute cutting forces and produce a smoother surface finish. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Compact 40 mm diameter and internal coolant combine to provide stable cutting and extended insert life; compatibility with RDMT 1003 indexable inserts simplifies maintenance and logistics. Order the round face mill directly via Metav Werkzeuge or ask our consultants if needed. Round face mill for RDMT 1003 – 40 mm with internal coolant (Teknik Makina) The Round face mill for RDMT 1003 indexable inserts is a compact milling head engineered for precise face milling in confined setups, offering internal coolant for improved tool life and consistent surface finish. Compact 40 mm diameter for tight spaces Integrated internal coolant for chip evacuation Compatible with RDMT 1003 indexable inserts Four cutting edges for stable material removal Precision and productive cutting for small setups The compact design delivers high repeatability in confined workstations. With a 40 mm diameter and a total length of 40 mm, the cutter is suited to applications where space and tool overhang are limited. The use of standard RDMT 1003 indexable inserts keeps tooling cost predictable and streamlines inventory. A reduced overhang and balanced geometry help to lower vibration, which translates into a more consistent surface finish and longer insert life—advantages that matter when cycle times and part quality are measured precisely. Internal coolant to protect inserts and improve cycle stability Built-in internal coolant directs cutting fluid precisely to the cutting zone, enhancing heat management and chip evacuation. This targeted supply reduces thermal load on the insert edges and slows wear, which reduces tooling changes and supports continuous production. In practical terms, the internal coolant contributes to steady cutting conditions and fewer rework events, providing a clear efficiency gain for shop floors focused on throughput and part quality. Robust fastening and service-friendly assembly Maintenance and insert changes are straightforward thanks to the Torx fastening system: a T15 Torx key secures the insert with M3.5x8.5 screws. The fast, standardised clamp method reduces downtime during service intervals and is compatible with widely available maintenance tools. The assembly's low mass (0.22 kg) and well-defined mounting interface also simplify handling and reduce wear on toolholding systems during frequent tool changes. Versatile milling head for predictable results The four cutting edges enable even material removal and stable milling performance across a variety of tasks that require a compact cutter head. The 16 mm mounting bore ensures a solid connection to the arbor or toolholder, maintaining concentricity and minimising run-out. Together, these attributes support repeatable results and predictable tool life, which are essential for production planning and process control in industrial machining environments. Choose Teknik Makina’s compact face mill with internal coolant for reliable, space-saving face milling—contact Metav Werkzeuge in Emmerich for tailored advice and dependable supply. Technical data SKU: T289-1TM Manufacturer: Teknik Makina Product type: Round face mill Facts Diameter: 40 mm Overall length: 40 mm Mounting bore: 16 mm Weight: 0.22 kg Cutting edges: 4 Fastening screw: M3.5x8.5 Torx key: T15 Special features Compatible with RDMT 1003 indexable inserts Internal coolant Indexable-insert face milling head SKU T289-1TM FAQ Which inserts fit this cutter? The cutter is compatible with RDMT 1003 indexable inserts; using this standard keeps insert logistics simple and cost-effective. Does the milling head have internal coolant? Yes, the tool features internal coolant that directs fluid to the cutting zone to help control temperature and chip evacuation. What are the key dimensions of the milling head? The milling head has a diameter of 40 mm, an overall length of 40 mm, and a 16 mm mounting bore. Which fastening hardware is used for the inserts? Inserts are secured with M3.5x8.5 screws operated with a T15 Torx key for quick and reliable clamping. Who manufactures the tool and what is the SKU? The tool is manufactured by Teknik Makina and sold under SKU T289-1TM for straightforward ordering and tracking. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact 40 mm design combined with internal coolant and compatibility with RDMT 12T3 indexable inserts to secure stable, high-performance face milling. Order the cutter through Metav Werkzeuge for reliable supply or contact our advisers for application guidance. Round insert cutter T281-1TM — 40 mm diameter, internal coolant (Teknik Makina) A Round insert cutter for RDMT 12T3 indexable inserts, engineered for compact face milling and efficient material removal in confined setups. 40 mm diameter for compact milling Internal coolant supply Compatible with RDMT 12T3 inserts Four cutting edges for efficient removal Compact cutter geometry for controlled, consistent machining The compact 40 mm diameter and streamlined body deliver a balanced combination of rigidity and accessibility for face milling in restricted spaces. With four cutting edges arranged for evenly distributed cutting forces, the head reduces vibration and supports consistent surface finish during interrupted and continuous cuts. This geometry is particularly beneficial when fixture space is limited, where a larger tool would compromise stability or prevent access. Internal coolant for improved tool life and process reliability Integrated internal coolant channels supply cutting fluid close to the cutting zone, reducing heat generation and aiding chip evacuation. Better cooling lowers thermal load on the insert, which translates into extended tool life and more reliable edge retention. For workshops aiming to reduce downtime, this targeted coolant approach helps maintain dimensional accuracy and surface quality over longer tool cycles. Secure clamping and fast indexable-insert changes Insert retention uses a Torx screw specification ( M3.5x8.5 ) tightened with a T15 key, providing secure clamping with reproducible seating force. The indexable design of RDMT 12T3 inserts enables rapid corner changes without reclamping the whole head, cutting maintenance time and simplifying tool logistics. The light overall mass (0.236 kg) further eases handling when preparing toolsets, reducing changeover effort at the machine. Efficient face milling across general applications Designed as a face milling head, the cutter supports versatile machining tasks where compact form factor and coolant supply are priorities. The pairing with RDMT 12T3 indexable inserts allows selection of insert grades suited to particular materials or cutting conditions, making the head a flexible choice for batch production and mixed-operation workshops. Operational stability and straightforward insert replacement help to uphold productivity and part quality in day-to-day production. Discuss suitability with Metav Werkzeuge in Emmerich — the Teknik Makina round insert cutter with internal coolant (SKU T281-1TM) can be specified and delivered directly; contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice Technical data Article number: T281-1TM Product type: Round insert cutter Brand: Teknik Makina ECLASS: 21180902 Indexable insert: RDMT 12T3 Facts Diameter: 40 mm Total length: 40 mm Weight: 0.236 kg Cutting edges: 4 Special features Internal coolant supply Torx screw: M3.5x8.5 Torx key: T15 Category: Face milling head (Planmesserkopf) FAQ What insert type is required for this cutter? The cutter accepts RDMT 12T3 indexable inserts; the TekniK Makina round insert cutter T281-1TM is designed specifically for that insert geometry. Does the cutter provide coolant to the cutting zone? Yes, the T281-1TM features internal coolant channels that deliver fluid directly to the insert rake zone to aid cooling and chip evacuation. Which toolholder or application suits this head best? The head is intended as a compact face milling solution; it is suitable where access is limited and coolant-fed machining is required, with the cutter working as a face milling head in general milling setups. How are the inserts secured and changed? Inserts are clamped with a Torx screw ( M3.5x8.5 ) tightened with a T15 key, allowing quick, repeatable index changes without complex procedures. Is the cutter appropriate for rapid changeover in production? Yes, the indexable insert system and secure Torx clamping enable fast insert replacement, supporting efficient tool changeovers and minimised machine downtime. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact face milling solution that combines a 40 mm cutting diameter, internal coolant and six cutting edges for consistent component finishes and reduced changeover time. The compact design and secure Torx fastening mean reliable mounting and fast insert changes — order or request tailored advice through Metav Werkzeuge for swift supply and application support. Face milling head T480-2TM – 40 mm, internal coolant, for BLMP 0603 indexable inserts (Teknik Makina) A face milling head T480-2TM engineered for accurate face machining with BLMP 0603 indexable inserts, optimised for compact toolholders and industrial milling applications. 40 mm diameter for compact face milling Internal coolant for improved tool life Compatible with BLMP 0603 indexable inserts Six cutting edges for efficient material removal High-efficiency face machining for compact setups The compact 40 mm diameter of this face milling head delivers a balance between accessibility and material removal capability, making it suitable for tight fixtures and multi-spindle arrangements. With six cutting edges, fewer tool changes are required, which reduces non-productive time and supports continuous production. The 100° cutting angle is designed to control cutting forces and promote even surface contact, meaning a consistent finish across the workpiece without compromising cycle time. Prolonged insert life through targeted coolant supply The integrated internal coolant channel directs lubricant and coolant close to the cutting zone, which helps manage temperature at the cutting edge and supports chip control. This focused cooling reduces thermal stress on inserts and can extend service intervals, improving overall process stability. For operations where coolant supply is part of the machining strategy, the head’s internal channel supports reliable coolant delivery without additional external adapters. Straightforward compatibility and quick serviceability Designed for use with BLMP 0603 indexable inserts and compatible with Taegutec tooling, the milling head simplifies procurement and tool preparation. Fast replacement of inserts is facilitated by the standard T8 Torx interface and M3x6.2 fixing screws, enabling rapid clamping and secure seating. The straightforward fastening system reduces changeover complexity and helps maintain consistent clamp torque, supporting repeatable machining results. Ready for industrial integration and compact tool assemblies With an overall length of 45 mm and a mass of 0.262 kg, this milling head suits compact tool assemblies where weight and reach affect spindle dynamics. The robust design from Teknik Makina matches industrial demands for repeatability and straightforward maintenance procedures. Where process reliability and simple stocking are priorities, the component’s form factor supports efficient storage and handling within a central toolroom or production cell. Contact Metav Werkzeuge for application-specific recommendations and to secure supply of the Teknik Makina face milling head with internal coolant — enquiries are handled directly from our Emmerich location for fast and transparent fulfilment. Technical data Article number: T480-2TM Designation: Face milling head for BLMP 0603 indexable inserts Manufacturer: Teknik Makina Dimensions & weight Diameter: 40 mm Overall length: 45 mm Weight: 0.262 kg Number of cutting edges: 6 Cutting angle: 100° Features & compatibility Internal coolant: yes Compatible with Taegutec BLMP 0603 indexable inserts Torx key: T8 Torx Fixing screw: M3x6.2 FAQ Which inserts fit this milling head? The head accepts BLMP 0603 indexable inserts and is specified for compatibility with Taegutec inserts for matching insert geometries. Does the tool provide internal coolant? Yes, the face milling head includes an internal coolant channel to supply lubricant directly to the cutting zone. How many cutting edges are available before insert change? The milling head is set up with six cutting edges, which extends effective cutting intervals compared with fewer-edge configurations. What are the key dimensions and mass of the head? The component has a diameter of 40 mm, overall length of 45 mm and a weight of approximately 0.262 kg. Which fastening and screw sizes are required for insert clamping? Insert clamping uses a T8 Torx interface with M3x6.2 screws for secure and repeatable fixing. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high-performance tool that combines a 40 mm diameter, four cutting edges and compatibility with SDMT 09T3 indexable inserts for reliable face milling results; order the face milling head directly via Metav Werkzeuge or ask the consultants if additional technical detail is required. Face milling head T362TM by Teknik Makina — compact 40 mm head for SDMT 09T3 indexable inserts Face milling head T362TM for SDMT 09T3 indexable inserts, designed for accurate facing and light to medium material removal in workshop and production settings 40 mm diameter for compact milling Four cutting edges for efficient removal 16 mm shank for secure toolholder fit Compatible with ZCC SDMT 09T3 inserts Improved productivity from compact tool geometry The compact design delivers a 40 mm diameter footprint while retaining robust cutting performance through four cutting edges. This geometry reduces tool overhang and improves stability in shoulder and face milling operations, which in turn reduces vibration and helps maintain consistent cycle times. Compatibility with SDMT 09T3 indexable inserts manufactured by ZCC ensures access to widely available grades and geometries, enabling optimized cutting parameters for alloyed steels and general workshop materials. The result is a reliable balance between removal rate and surface quality, suited to repetitive machining tasks. Fast insert changes and secure clamping reduce downtime Maintenance and insert replacement are straightforward thanks to the standardised fastening: Torx screw M3.5x8.5 tightened with a T15 key, and a compact 16 mm shank for secure seating in smaller toolholders. The robust screw and key combination keeps insert clamping precise, minimising the need for repeated adjustments and lowering machine downtime. With a lightweight assembly of approximately 0.215 kg, handling and tool change operations are simplified, which benefits small-batch production and mixed-operation shops where quick turnaround is essential. Consistent surface finish through stable cutter head design A well-balanced cutter head profile and four equally spaced cutting edges contribute to a steady cutting action and predictable chip formation. The resulting surface integrity supports downstream processes such as finishing and inspection without the need for excessive rework. The construction offers predictable deflection characteristics under standard cutting loads, so finishing cycles can be reliably planned and quality targets achieved with fewer trial cuts. This stability is particularly valuable when machining interrupted cuts or short overhangs. Compatibility and supply reliability for workshop integration Designed for indexable insert systems, the head matches SDMT 09T3 inserts from ZCC, making tool sourcing and grade selection straightforward. The compact overall length and standard shank diameter ease integration into existing toolholder inventories. For procurement and logistics, Metav Werkzeuge’s Emmerich location acts as a dependable supply channel, offering a broad range of complementary tooling and accessories to complete a machining setup. Technical documentation and product files linked to the SKU support planning and maintainability in production environments. Contact Metav Werkzeuge in Emmerich for tailored technical advice and reliable supply of the T362TM face milling head, ensuring fast integration into production workflows Technical Data SKU: T362TM Manufacturer: Teknik Makina Compatible inserts: SDMT 09T3 Compatible insert manufacturer: ZCC Description (EN): for SDMT 09T3 Indexable Inserts Facts Diameter: 40 mm Shank diameter: 16 mm Overall length: 40 mm Cutting edges: 4 Weight: 0.215 kg Special features Torx screw M3.5x8.5 Torx key: T15 Suitable for indexable insert face milling Compact design for reduced overhang FAQ Which inserts fit this cutter head? The head is designed for SDMT 09T3 indexable inserts; compatibility with ZCC SDMT 09T3 grades is specified for the T362TM face milling head. What fastening hardware is used for the inserts? Inserts are secured with a Torx screw M3.5x8.5, tightened using a T15 key, providing secure and repeatable clamping for the cutter head. What toolholder dimensions are required? The cutter requires a toolholder with a 16 mm shank bore for correct seating and rigid clamping of the assembly. Is the head suitable for heavy roughing? The compact geometry and four-edge configuration are optimised for facing and light to medium material removal; for heavy roughing, a larger dedicated roughing head is recommended. What is the weight and size of the cutter head? The assembly has a 40 mm diameter, 40 mm overall length and weighs approximately 0.215 kg, making it suitable for compact tool setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, purpose‑built design that combines 40 mm cutting head diameter with a 45° cutting angle and internal coolant to deliver consistent face‑milling results; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Face milling head T319-1TM – 40 mm diameter, internal coolant (Teknik Makina) Face milling head T319-1TM for SNKX 1206 indexable inserts, engineered for face‑milling operations where surface quality and reliable chip evacuation are essential 40 mm cutting head diameter Internal coolant for improved chip control Compatible with SNKX 1206 indexable inserts 45° cutting angle for smooth surface finish Higher throughput with predictable cutting performance The compact cutter body and the 45° rake geometry are combined to reduce cutting forces and to favour a stable engagement during face milling tasks. By pairing a robust cutter body with SNKX 1206 indexable inserts (Korloy), the assembly achieves an efficient balance between material removal and surface finish. The 40 mm head diameter and the stated maximum cutting diameter of 53 mm permit consistent passes on small to medium workpieces, supporting predictable cycle times and reduced rework. This results in measurable productivity gains on repetitive production runs. Improved process reliability through internal coolant and secure fixing Internal coolant is routed through the cutter to the insert pockets, promoting active cooling at the cutting edge and cleaner chip breakage; this feature helps extend insert life and maintain dimensional consistency. The head uses M4x12.5 fastening screws with a T15 Torx drive for secure clamping and simple torque application during tool changes. The three cutting edges arrangement provides balanced cutting action and reduces vibration, which supports repeatable component quality across batches and minimises downtime for adjustments. Designed for easy integration and dependable handling With an overall length of 45 mm and a net weight of 0.417 kg, the cutter head is compact enough for tight setups while still offering rigid support for the insert geometry. The body accepts SNKX 1206 indexable inserts and is compatible with Korloy insert types, allowing straightforward stocking and inventory management. Maintenance is simplified by standardised fasteners and the common insertion system, so toolroom staff can replace inserts and secure the head quickly, keeping machine uptime high and maintenance effort low. For technical consultation or to equip a workstation with the T319-1TM face milling head, contact Metav Werkzeuge in Emmerich to discuss application specifics and delivery options. Technical data SKU: T319-1TM Product type: Face milling head Brand: Teknik Makina Facts Diameter: 40 mm Overall length: 45 mm Weight: 0.417 kg Max cutting diameter: 53 mm Cutting angle: 45° Number of cutting edges: 3 Fastening screw: M4x12.5 Torx key: T15 Internal coolant: Yes Special features Compatible with SNKX 1206 indexable inserts (Korloy) Internal coolant for direct edge cooling Compact body for small to medium workpieces FAQ Is the milling head compatible with SNKX 1206 inserts? Yes. The T319-1TM is designed specifically for SNKX 1206 indexable inserts and is compatible with Korloy insert variants. Does the head provide coolant directly to the cutting edge? The cutter features internal coolant channels that deliver fluid close to the insert, aiding chip control and thermal management for prolonged insert life. What fastening hardware is required for installation? The assembly uses M4x12.5 screws tightened with a T15 Torx key to secure inserts and ensure a consistent clamping force. Which applications benefit most from this cutter head? The design suits face‑milling and finishing operations on small to medium workpieces where a 45° cutting angle and controlled chip evacuation improve surface quality. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the robust 100° cutting geometry and precise 16 mm shank for dependable face milling operations; the combination of secure Torx fastening and compatibility with ENMX 0604 indexable inserts supports consistent tool performance and fast insert replacement — order the face milling head directly via Metav Werkzeuge or request technical advice from our consultants. Face milling head T763TM — 100° face milling head for ENMX 0604 indexable inserts (Teknik Makina) A face milling head engineered for 100° ENMX 0604 indexable inserts, designed for reliable face milling and straightforward insert changes 100° cutting angle for heavy face milling Fits ENMX 0604 indexable inserts (YG-1 compatible) 16 mm shank diameter, 40 mm head diameter Secured with M2.5x7 Torx screw; T8 key Reliable cutting geometry for consistent material removal The face milling head offers a 100° cutting angle that is optimised to deliver stable contact during face milling cycles. This geometry supports a controlled cutting engagement that can reduce vibration and promote even load distribution across the insert edge. With a head diameter of 40 mm and an overall height of 40 mm, the tool body provides a compact yet rigid platform that contributes to repeatable results on each pass. The design therefore emphasises process reliability and predictability for production runs where consistency matters. Precision fit and secure clamping for operational safety A precise 16 mm shank diameter ensures a defined fit in tool holders that accept that mounting dimension, reducing radial play and improving concentricity. The insert is secured with a M2.5x7 Torx screw, driven by a T8 key, which simplifies maintenance while ensuring a firm mechanical connection. The number of effective cutting edges (six) and the solid clamping arrangement minimise the risk of insert movement under load, supporting safe, long-term operation and straightforward changeover procedures. Compatibility and practical handling to save shop time Compatibility with ENMX 0604 indexable inserts and documented suitability for YG-1 inserts makes selection of replacement cutting parts straightforward and traceable. The tool body is configured for fast insert swaps and secure fastening, which shortens downtime during maintenance. Clear specification of the mounting size and fastening standard helps in planning tooling inventories and in matching the cutter to existing holders. As a compact face cutter, it is suitable for shops seeking a reliable milling head that integrates into established tooling systems. For precision face milling with Teknik Makina quality, contact Metav Werkzeuge for tailored supply and technical advice — info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: T763TM ECLASS: 21181015 Manufacturer: Teknik Makina Facts Head diameter: 40 mm Overall height: 40 mm Shank diameter: 16 mm Number of cutting edges: 6 Cutting angle: 100° Special features Compatible inserts: ENMX 0604 Insert supplier compatibility: YG-1 Torx screw: M2.5x7 Torx key: T8 SKU / UID: T763TM FAQ Which inserts are compatible with this face milling head? The face milling head accepts ENMX 0604 indexable inserts; compatibility with YG-1 inserts is specified for straightforward replacement. What is the cutting angle and why is it relevant? The cutter uses a 100° cutting angle, which helps to stabilise the cutting engagement and supports controlled material removal during face milling. How is the insert fastened to the tool? The insert is secured by a M2.5x7 Torx screw, tightened with a T8 key, providing a reliable mechanical clamp that simplifies insert changes. What shank size is required for mounting the tool? A tool holder with a 16 mm shank reception is required to mount the face milling head with the specified fit and concentricity. How many cutting edges are available per assembly? The cutter body is configured with six cutting edges, allowing efficient use of the insert geometry as intended by the indexable design. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, precision-focused solution that combines a 40 mm diameter, internal coolant and compatibility with BLMP 0904 indexable inserts to maintain stable face-milling cycles and consistent surface quality. Order directly via Metav Werkzeuge or request tailored advice from our consultants for optimal integration into production. Planmesserkopf – face milling head with 40 mm diameter and internal coolant by Teknik Makina A Planmesserkopf engineered for efficient face milling with BLMP 0904 indexable inserts, designed to deliver compact, repeatable surfacing performance in small to medium workshop setups. 40 mm diameter for compact face milling Internal coolant supply for improved chip evacuation Compatible with BLMP 0904 indexable inserts Five cutting edges for efficient material removal Torx T10 mounting for secure insert retention Compact diameter for stable, predictable machining results A reduced tool diameter contributes to lower overhang and improved rigidity, which directly benefits cycle stability and dimensional consistency. The 40 mm cutter body is advantageous where space is limited or where minimised tool projection is required; by limiting deflection, the design enables more accurate planar cuts and reduced rework. The head’s configuration with five cutting edges balances material removal rate and surface quality, making it suitable for finishing and light roughing tasks. Integrated coolant for longer tool life and better finishes The built-in internal coolant channel delivers cutting fluid directly to the cutting zone, which helps to evacuate chips, reduce cutting temperatures and prevent built-up edge. In practice, this results in extended tool life and a more consistent surface finish across production runs. For workshops transitioning from external coolant setups, the internal supply reduces reliance on external nozzles and simplifies machine setup while improving cooling efficiency at the insert cutting edge. Robust mounting and simple service for productive workshops A secure fastening system based on T10 Torx engagement and M3.5×8.5 screws ensures reliable insert retention during heavier cuts and frequent index changes. The compact 40 mm overall length and light mass contribute to fast index and tool changes, shortening setup times on multi-shift floors. Compatibility with BLMP 0904 indexable inserts and proven fit with Taegutec-specified inserts supports standardisation of spare parts across fleets and simplifies inventory management. For a production-ready face milling solution from Teknik Makina, contact Metav Werkzeuge for specification support and ordering assistance—email info@metav-werkzeuge.com or call +49 2822 7131930 to match the cutter head precisely to the application. Technical data Article number: T485-1TM Label: 40mm Planmesserkopf BLMP 0904 L40mm mit Innenkühlung Manufacturer: Teknik Makina Facts Diameter: 40 mm Overall length: 40 mm Shank/holder diameter: 16 mm Weight: 0.176 kg Cutting edges: 5 Cutting angle: 100° Special features Internal coolant Compatible with BLMP 0904 indexable inserts Compatible with Taegutec inserts Torx T10 key Torx screw M3.5×8.5 FAQ Which indexable inserts fit this cutter head? The cutter head accepts BLMP 0904 indexable inserts and is compatible with inserts specified by Taegutec for the same seat geometry. Does the milling head provide internal coolant? Yes, the Planmesserkopf includes internal coolant, supplying fluid directly to the cutting zone for improved chip evacuation and tool life. What are the key dimensions to consider for machine setup? The head has a 40 mm diameter, 40 mm overall length and a 16 mm shank/holder diameter, which helps to assess rigidity and clearance for the intended machine. How are inserts secured in the head? Inserts are fastened using a T10 Torx interface and M3.5×8.5 screws, ensuring stable retention during machining and straightforward servicing. Is this cutter suitable for compact or confined setups? Yes, the compact design and reduced overhang of the 40 mm head make it well suited to confined setups where rigidity and minimal projection are critical. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of compact 40 mm diameter design, integrated internal coolant and compatibility with LNMU 0303 indexable inserts to maintain consistent surface quality and higher throughput. Order the tooling directly via Metav Werkzeuge or consult our specialists for application matching. Face mill head for LNMU 0303 indexable inserts — 40 mm diameter with internal coolant by Teknik Makina The face mill head is designed for compact, high-efficiency facing operations using LNMU 0303 indexable inserts in general machining and production environments. 40 mm diameter for compact milling Internal coolant for longer tool life 6 cutting edges for efficient stock removal Compatible with LNMU 0303 indexable inserts High-efficiency facing with compact dimensions The compact 40 mm diameter milling head delivers stable cutting for tight setups while enabling a respectable material removal rate when space is limited. The combination of a 55° cutting angle and 6 cutting edges reduces vibration and distributes cutting forces, which helps to maintain cycle times and tool-change intervals. This configuration supports predictable process behaviour in series production and small-batch workshops, translating blade geometry into measurable throughput gains. Integrated coolant channel for consistent surface quality An internal coolant channel provides directed cooling and chip control at the cutting zone, which reduces thermal load and improves surface finish and repeatability. By promoting efficient chip evacuation and cooling the cutting edge, the system extends tool life and reduces rework. For applications where consistency across multiple faces is essential, the coolant feed is a decisive factor in reducing micro-welds and edge build-up during prolonged cuts. Straightforward integration and proven compatibility Designed specifically for LNMU 0303 indexable inserts, the tool accepts inserts from Tungaloy and OKE, enabling flexible supply options and easy re-tooling in mixed-vendor environments. The head mounts on a 16 mm connection and is secured with Torx T8 fasteners using M2.5x7 screws, supporting quick replacement and reliable clamping. With a compact total length and a lightweight build, the milling head is suitable for retrofitting into existing tool setups without major adaptation, simplifying spare-part logistics. For precise facing jobs where coolant supply and insert compatibility matter, choose the Teknik Makina face mill head and contact Metav Werkzeuge for application advice and procurement: info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: T728-1TM Manufacturer: Teknik Cutting Tools Product type: Face mill head Facts Diameter: 40 mm Overall length: 40 mm Shank / mount diameter: 16 mm Weight: 0.275 kg Cutting edges: 6 Cutting angle: 55° Special features Internal coolant Designed for LNMU 0303 indexable inserts Compatible with Tungaloy and OKE inserts Torx key: T8 Torx screw: M2.5x7 ECLASS: 21181015 FAQ What insert type fits this milling head? The milling head accepts LNMU 0303 indexable inserts, utilising the standard seat and clamping geometry for this insert family. Is the cutter suitable for use with Tungaloy inserts? Yes, the tool is compatible with inserts from Tungaloy as well as OKE, enabling flexible sourcing. Does the head provide internal coolant? Yes, the head features internal coolant to aid chip evacuation and tool life under continuous operation. What are the mounting and fastening details? Mounting is via a 16 mm connection and the cutter is secured using Torx T8 fasteners with M2.5x7 screws; spare fixings match these specifications. Which SKU should be ordered for this item? Order the item under SKU T728-1TM for the 40 mm face mill head compatible with LNMU 0303 inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the compact 40 mm diameter, integrated internal coolant and five cutting edges for efficient, repeatable face milling; order the T505TM directly via Metav Werkzeuge or contact our consultants for specification support. Face‑milling head T505TM — 40 mm with internal coolant (Teknik Makina) A face‑milling head designed for LNMX 1004 indexable inserts, delivering compact face cutting with built‑in coolant for stable machining. 40 mm diameter for compact face milling Internal coolant for improved chip evacuation Accepts LNMX 1004 indexable inserts (Korloy) 90° cutting angle with five cutting edges Consistent machining and higher throughput The compact 40 mm cutter body concentrates cutting forces for steady performance on short overhangs. Fitted with five cutting edges and a 90° cutting angle, this head promotes uniform material removal and predictable surface finish — a real advantage where cycle time and repeatability matter. The construction minimises vibration in constrained set‑ups, translating tool geometry into demonstrable production gains for batch and single‑piece work alike. Controlled cooling for longer insert life Integrated internal coolant supplies lubrication and cooling directly to the cutting zone, which reduces thermal load and helps prevent built‑up edge on the inserts. Used with LNMX 1004 indexable inserts (compatible with Korloy grades), the coolant path supports consistent chip evacuation and prolongs insert life, lowering tooling costs and decreasing unscheduled stoppages. For users unfamiliar with internal coolant, this means fewer thermal distortions and steadier cutting performance over extended runs. Quick servicing and secure clamping Maintenance is straightforward thanks to the standardised fastenings: T15 Torx engagement for insert retention and M4x10 screws for secure fixing. The head’s low mass (0.19 kg) and accessible screw interfaces allow rapid index changes and minimal downtime, which suits production environments where tool change frequency impacts throughput. The clear, common fastening format reduces the need for special tools and supports a predictable maintenance routine. Compact compatibility for versatile workshops Model T505TM from Teknik Makina suits compact machining stations and toolrooms that require small, dependable face‑milling solutions. Its form factor and insert compatibility simplify stockholding, as the head uses the widely available LNMX 1004 inserts. The combination of reduced inventory complexity and a proven head design supports smoother workflow integration in both the workshop and production line. For tailored advice on integrating the T505TM into existing setups or to secure stock from our Emmerich distribution, contact Metav Werkzeuge for reliable supply and consultation. Technical data Article number: T505TM Product type: Face‑milling head Brand: Teknik Makina Label: 40mm Planmesserkopf LNMX 1004 L40mm mit Innenkühlung Key data Diameter: 40 mm Overall length: 40 mm Weight: 0.19 kg Cutting edges: 5 Cutting angle: 90° Screw: M4x10 Torx key: T15 Features Internal coolant Fits LNMX 1004 indexable inserts Compatible with Korloy inserts Compact design for short overhangs FAQ Which indexable inserts fit this head? The T505TM accepts LNMX 1004 indexable inserts and is compatible with Korloy grades suitable for that insert designation. Does the head provide coolant supply? Yes, the head has internal coolant, delivering fluid directly to the cutting zone to assist chip evacuation and reduce insert wear. What are the key dimensions of the cutter? The cutter has a 40 mm diameter and an overall length of 40 mm, designed for compact face‑milling operations. How many cutting edges does it offer and what is the angle? The tool is built with five cutting edges and a 90° cutting angle, promoting consistent face finishes and effective material removal. Which fastening and screw types are required for insert changes? Insert retention uses a T15 Torx interface with M4x10 screws for secure and rapid replacement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the small footprint and internal coolant to maintain steady chip evacuation while the six cutting edges ensure efficient material removal; order directly via Metav Werkzeuge or consult our specialists for integration advice. Planmesserkopf – Face milling head, 40 mm diameter, internal coolant (Teknik Makina) Planmesserkopf for precise face milling with LOGU 0303 indexable inserts, designed for compact toolholders and high repeatability in production environments 40 mm diameter for compact milling heads Internal coolant for effective chip control Compatible with LOGU 0303 Kyocera inserts Compact design that keeps cycle times low The compact 40 mm diameter face milling head combines a small envelope with a robust cutting concept to reduce setup constraints on smaller machines. With six cutting edges, load is distributed evenly across inserts, which improves surface finish and allows higher material removal per pass. The reduced overhang and the 16 mm mounting diameter contribute to better rigidity and less vibration, resulting in more consistent results on aluminium, steel and general workshop materials. This configuration supports efficient machining while keeping spindle loads predictable. Secure clamping and directed coolant for consistent tool life Built for reliable clamping and simple servicing, the tool uses M3x7 Torx screws tightened with a T8 key for straightforward insert changes and repeatable seating. The integrated internal coolant directs cutting fluid to the cutting zone, improving cooling and chip evacuation which extends insert life and reduces rework. Compatibility with LOGU 0303 indexable inserts from Kyocera ensures a wide choice of geometries for finishing or roughing. The combination of secure fastening and internal coolant helps maintain dimensional stability during longer cycles. Practical workshop benefits and straightforward maintenance Weighing just 0.283 kg and finished for balanced rotation, the head keeps spindle stress low and minimises setup time when replacing or indexing inserts. The compact overall length of 40 mm supports tight toolpacks and simple collision planning. Supplied as a ready-to-fit milling head (SKU T731-1TM) from Teknik Makina, it suits job shops and production lines that prioritise uptime and predictable performance. The design reduces maintenance intervals and simplifies stocking: one head plus a set of LOGU 0303 inserts covers many common face-milling tasks. For application advice or technical confirmation for the Teknik Cutting Tools face milling head T731-1TM, contact Metav Werkzeuge — our specialists in Emmerich will advise on integration, suitable inserts and machining parameters. Technical data SKU: T731-1TM Manufacturer: Teknik Makina Product: Face milling head for LOGU 0303 indexable inserts Facts Diameter: 40 mm Overall length: 40 mm Mounting / bore diameter: 16 mm Number of cutting edges: 6 Weight: 0.283 kg Torx screw: M3x7 Torx key: T8 Special features Internal coolant Compatible with LOGU 0303 indexable inserts Suitable for Kyocera insert range Compact design for improved rigidity Balanced for reduced vibration FAQ What insert type does this face milling head use? The face milling head accepts LOGU 0303 indexable inserts; the unit is configured for Kyocera-compatible geometries to cover finishing and roughing tasks. Is there internal coolant supply on the tool? Yes, the Planmesserkopf features internal coolant, which delivers lubricant directly to the cutting edge to improve tool life and chip evacuation. Which fastening hardware is required for insert changes? Insert retention is via M3x7 Torx screws tightened with a T8 key; this ensures repeatable clamping and quick service on the workshop floor. What are the mounting dimensions and balance considerations? The head has a 16 mm mounting diameter and a compact 40 mm overall length; its low mass (0.283 kg) helps maintain spindle balance and reduce vibration. Can the T731-1TM be used on small milling machines? Yes, the compact envelope and secure clamping make the T731-1TM suitable for smaller CNC mills and job-shop machinery where space and rigidity are considerations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com