Gibt es einen Hahn und Kolb Online Shop?

Take advantage of the combination of compact geometry, internal coolant, and compatibility with RCKT 1204 indexable inserts for reliable face milling and reduced downtime. Order the cutter directly via Metav Werkzeuge or consult the Metav specialists for application advice. Indexable Insert Face Mill T460-1TM — 50 mm, internal coolant (Teknik Makina) A Indexable Insert Face Mill T460-1TM designed for precise face milling with RCKT 1204 indexable inserts, offering controlled chip evacuation via internal coolant for stable cutting conditions. 50 mm diameter for compact face milling Internal coolant for better chip evacuation Compatible with RCKT 1204 inserts (Sandvik) Four cutting edges for smooth material removal Consistent metal removal through internal-coolant control The milling head employs internal coolant routed directly to the cutting zone to support consistent chip evacuation and thermal stability. With a 45° cutting angle and four cutting edges, the design reduces cutting forces and promotes even wear across inserts, which in turn extends indexable-insert life and lowers tooling costs per component. For production settings where repeatability is essential, the integrated coolant path helps maintain a predictable process window and reduces the risk of built-up edge and thermal softening. Compact form factor for tight fixtures and quick index changes At 50 mm diameter and 40 mm overall length, the compact geometry of this cutter suits restricted setups and multi-spindle arrangements. The light construction (approx. 0.287 kg) minimises centrifugal load and is beneficial where balance and rapid acceleration matter. Insert clamping uses a T15 Torx drive and M3.5x8.5 screws for secure fastening and straightforward replacement; this standardisation simplifies workshop logistics and shortens maintenance cycles. Compatibility with RCKT 1204 indexable inserts—including those from Sandvik—ensures ready availability of grades and geometries for varying roughing and finishing tasks. Predictable performance that supports process efficiency Designed for dependable face milling operations, the cutter head provides a stable cutting geometry that facilitates higher feed per tooth and repeatable material removal rates. The combination of controlled coolant delivery and a 45° approach reduces vibrations and contributes to improved surface finish with fewer interruptions. Supplied by Teknik Makina and marketed via Metav, the tool is suited to serial production as well as jobbing work where consistent cycle times and reduced rework are priorities. Contact Metav Werkzeuge for technical advice and availability of the Teknik Makina T460-1TM face mill with internal coolant and RCKT 1204 compatibility Technical Data Article number: T460-1TM Label: 50mm Rundplattenfräser RCKT 1204 L40mm mit Innenkühlung Product type: Indexable insert face mill Manufacturer: Teknik Makina Data Diameter: 50 mm Overall length: 40 mm Weight: 0.287 kg Number of cutting edges: 4 Cutting angle: 45° Torx key: T15 Torx screw: M3.5x8.5 Special features Internal coolant: yes Compatible inserts: RCKT 1204 Compatible insert manufacturer: Sandvik FAQ Which inserts are suitable for this milling head? The cutter accepts RCKT 1204 indexable inserts; compatible grades and geometries from Sandvik are suitable for a wide range of applications. Is coolant delivered directly to the cutting edge? Yes — the tool features internal coolant, which supplies the cutting zone to aid chip evacuation and thermal management. What fastening hardware is required for insert changes? Insert clamping uses a T15 Torx tool and M3.5x8.5 screws for secure fastening and straightforward replacement. Can the cutter be used in compact fixtures and multi-spindle machines? The compact dimensions (50 mm diameter, 40 mm length) and low mass (approx. 0.287 kg) make it well suited to tight setups and multi-spindle arrangements. Who manufactures the tool and what is the SKU? The tool is produced by Teknik Makina and marketed under SKU T460-1TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of compact design, internal coolant and secure Torx clamping for reliable facing operations; order directly via Metav Werkzeuge or consult the specialists for application advice. 50 mm Round Insert Face Mill for RDMT 1003 indexable inserts — Teknik Makina The 50 mm round insert face mill is a compact cutter engineered for precision facing and finishing with RDMT 1003 indexable inserts, suitable for CNC and workshop milling tasks. 50 mm diameter for compact face milling Internal coolant for improved tool life 4 cutting edges for stable material removal Torx T15 screws, M3.5x8.5 for secure clamping Maximise throughput with compact, efficient facing This cutter combines a 50 mm diameter with a short overall length to deliver efficient material removal in confined setups. The tool accepts RDMT 1003 indexable inserts, enabling cost-effective edge changes and predictable cutting behaviour. The presence of internal coolant channels reduces thermal stress at the cutting zone, which helps to maintain dimensional accuracy over longer runs and to extend insert life. The four effective cutting edges distribute load evenly, improving stability during face operations and lowering the risk of chatter. Faster tool changes and lower downtime through secure clamping Maintenance intervals are shortened by a design that prioritises quick insert replacement and secure fastening. The clamping system uses Torx T15 drive and M3.5x8.5 screws for reliable retention of the indexable inserts; this reduces rework from loose fastenings and ensures repeatable seating. A lightweight construction and compact overall length contribute to reduced spindle load and damped vibration, which benefits both surface finish and tool longevity. The modest 0.31 kg mass makes the cutter easier to handle during setup and exchange. Seamless integration into production workflows with trusted supply Engineered for industrial workshops and production lines, this face milling solution fits standard toolholders with a 22 mm bore and integrates into existing set-ups without elaborate adaptation. As part of a broader supply strategy, pairing this cutter with quality inserts and service from a reliable distributor reduces procurement complexity. Metav Werkzeuge acts as a local quality filter and supply partner from Emmerich, offering consistent availability and product range depth to support continuous production. For further technical details or to match inserts and holders, contact info@metav-werkzeuge.com or call +49 2822 7131930. For tailored application advice or to secure this Teknik Makina face mill from Metav Werkzeuge — contact the Emmerich team for reliable supply and technical matching. Technical data Article number/SKU: T290-1TM Brand: Teknik Makina ECLASS: 21180902 Product type: Round insert face mill Label: 50mm Rundplattenfräser RDMT 1003 L40mm mit Innenkühlung Facts Diameter: 50 mm Overall length: 40 mm Bore (arbor): 22 mm Cutting edges: 4 Weight: 0.31 kg Torx screw: M3.5x8.5 Torx key: T15 Internal coolant: Yes Special features For RDMT 1003 indexable inserts Internal coolant channel Compact design for reduced vibration Secure Torx clamping for repeatable seating FAQ Which inserts are compatible with this face mill? The face mill accepts RDMT 1003 indexable inserts; choosing grade and geometry should match the material and operation required. Is the cutter suitable for use with internal coolant systems? Yes — the design includes internal coolant channels to supply cutting fluid directly to the cutting zone. What is the arbor bore size required for mounting? The cutter is designed for a 22 mm arbor bore to fit compatible toolholders and adapters. How many cutting edges are available per cutter? The cutter features 4 cutting edges, allowing for balanced cutting and steady material removal. Are special screws or drivers required for insert changes? Insert clamping uses Torx T15 drive with M3.5x8.5 screws; a matching Torx driver is recommended for proper torque and secure fastening. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, performance-focused tool that combines a 50 mm diameter with internal coolant and five indexing positions for steady material removal; order the cutter directly via Metav Werkzeuge or ask the consultants for tailored machining advice. Round Insert Milling Cutter T140-1TM – 50 mm diameter, internal coolant (Teknik Makina) A round insert milling cutter designed for RDMT 1204 indexable inserts, optimised for compact face milling and light shoulder operations in CNC and milling centres 50 mm diameter for compact milling Internal coolant for improved chip evacuation Compatible with RDMT 1204 indexable inserts Five cutting edges for efficient material removal T15 Torx clamping, M3.5x8.5 screws included High-efficiency machining in compact setups A compact design with a 50 mm nominal diameter and an overall length 40 mm delivers a small footprint without compromising cutting capacity. The head’s configuration of five cutting edges enables continuous material removal with fewer interruptions for index changes, which increases throughput on short-cycle operations. For workshops constrained by tool overhang or with smaller spindle noses, this format provides process stability and keeps the cut consistent across passes. Better cooling, cleaner chips, longer life Built-in internal coolant channels direct cutting fluid to the cutting zone, reducing heat at the edge and improving chip evacuation. This results in more consistent surface finishes and reduced thermal wear on the inserts. Using indexable inserts reduces downtime: worn carbide tips are replaced quickly instead of replacing the whole cutter, so cycle times and maintenance windows are minimised while maintaining repeatable part quality. Secure clamping and straightforward service Clamping is executed via a T15 Torx interface using M3.5x8.5 screws for secure, repeatable seat pressure. The standardised fixing simplifies tool changes and ensures correct insert seating every time; a stable connection supports accurate machining and reduces vibration. The head is compatible with RDMT 1204 inserts, allowing flexible choice of grades and geometries for different materials and application requirements. Engineered for integration into production lines With a nominal mass of 0.311 kg, the cutter contributes little to tool stack weight while maintaining the rigidity required for stable face milling. The compact form factor makes it suitable for multi-spindle arrangements and automated tool changers. Where process reliability and predictable tool life are priorities, this head supports repeatable setups and easier inventory management through the use of standardised insert types such as RDMT 1204. For precise selection and availability of the T140-1TM, contact Metav Werkzeuge for application-matched recommendations and ordering: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T140-1TM Name: Round insert milling cutter for RDMT 1204 indexable inserts Manufacturer: Teknik Makina Core data Diameter: 50 mm Overall length: 40 mm Weight: 0.311 kg Cutting edges: 5 Internal coolant: yes Special features Compatible inserts: RDMT 1204 Torx key: T15 Torx screw: M3.5x8.5 Category: Face milling head FAQ Which inserts fit this milling head? The milling head accepts RDMT 1204 indexable inserts, a standard size for small-diameter face milling operations. Is there internal coolant supply? Yes, the cutter features internal coolant channels to improve chip removal and thermal stability at the cutting edge. How many indexing positions are available? The head is fitted for five cutting edges, allowing multiple index positions before insert replacement is needed. What fastening tools are required for insert changes? Insert clamping uses a T15 Torx key with M3.5x8.5 screws, providing secure and repeatable seating. What is the article number for ordering? Order using the article number T140-1TM to ensure the correct head and spec are supplied. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Compact construction and internal cooling combine to deliver consistent surface finish and extended insert life; with five cutting edges and compatibility with RPMT 1204 indexable inserts this cutter supports steady production performance. Order the round face mill directly via Metav Werkzeuge or ask our consultants if needed. Round face mill T711-1TM — 50 mm diameter, internal coolant (Teknik Makina) The Round face mill T711-1TM is a compact face milling head designed for finishing and semi-finishing operations using RPMT 1204 indexable inserts; suited to workshop and light industrial production where precise, repeatable results are required. 50 mm diameter for compact face milling Internal coolant supply for reliable chip evacuation Designed for RPMT 1204 indexable inserts Five cutting edges for efficient material removal Reliable cutting performance that raises throughput The milling head delivers a controlled, repeatable cut thanks to its five cutting edges and compact geometry. The arrangement of the inserts reduces vibration and balances cutting forces, which translates into a more consistent surface and fewer reworks. For applications that demand steady stock removal rather than heavy-duty roughing, the combination of modest diameter and a short overall length keeps tool overhang low, improving rigidity and enabling higher feed rates without compromising finish. The construction supports predictable tool life and reduces downtime between insert changes. Integrated cooling for cleaner chips and longer tool life Built-in internal coolant directs cutting fluid precisely to the cutting zone, aiding chip breaking and evacuation while lowering local cutting temperatures. This targeted cooling helps maintain edge integrity on the insert and reduces the risk of thermal damage during interrupted cuts. For operations where coolant access is limited, the internal supply improves process reliability and can contribute to lower tooling costs over time by protecting expensive indexable inserts. Compact design tailored for constrained setups With a diameter of 50 mm and an overall length of 40 mm, the cutter is optimised for workspaces with limited clearance. The short overhang improves stiffness and reduces chatter compared with longer heads, which benefits small- to medium-sized machining centres and milling heads. The low mass (approximately 0.327 kg) aids in quick tool changes and places less load on tool holders, making the head a practical choice for productive mixed-shops where flexibility and repeatable accuracy matter. Compatibility, handling and practical benefits The head is supplied for use with RPMT 1204 inserts and is compatible with inserts from Korloy, providing access to a range of grades for steel, stainless steel and cast materials as required. The design includes a standard mounting interface to suit a 22 mm arbor connection, making integration with common clamping systems straightforward. Clear identification by SKU T711-1TM simplifies procurement and inventory handling. The result is a versatile face milling solution that balances efficiency, cooling capability and compactness for everyday machining tasks. Contact Metav Werkzeuge to discuss suitability for specific materials and to arrange supply of the Teknik Makina T711-1TM round face mill with internal coolant for RPMT 1204 inserts Technical data Article number: T711-1TM Label: 50 mm round face mill RPMT 1204 L40 mm with internal coolant Brand: Teknik Makina eClass: 21180902 Core specifications Diameter: 50 mm Overall length: 40 mm Weight: 0.327 kg Cutting edges: 5 Compatible inserts: RPMT 1204 Internal coolant: yes Mounting bore: 22 mm Special features Compatible insert manufacturer: Korloy Product type: round face mill / face milling head SKU: T711-1TM FAQ What insert size does the cutter accept? The cutter accepts RPMT 1204 indexable inserts; the head is manufactured to accommodate that insert geometry. Is the tool suitable for finishing stainless steel? Yes, when fitted with the appropriate Korloy insert grade the head supports finishing and semi-finishing in stainless steel. How does the internal coolant improve machining? Internal coolant delivers fluid directly to the cutting zone, aiding chip evacuation and reducing cutting temperature for longer insert life when using this face milling head. What is the mounting interface for this cutter? The tool is designed for a 22 mm mounting bore and integrates with standard arbors and clamping systems for compact setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining robust 43° cutting geometry with a compact Ø50 mm design delivers consistent surface finish and predictable chip control; the secure 22 mm arbor mounting offers fast, repeatable set-up. Order directly via Metav Werkzeuge or consult our specialists for technical guidance. Planmesserkopf – Face milling head, 43° cutting angle, Ø50 mm (Teknik Makina) The Planmesserkopf is a compact face milling head engineered for finishing operations using OFCR 0704 indexable inserts. 43° cutting angle for smooth surface 50 mm diameter for tight spaces Accepts OFCR 0704 indexable inserts 22 mm arbor mounting with BK300 clamp High-precision cutting geometry for consistent finishes The face milling head uses a 43° cutting angle and four cutting edges to reduce cutting forces and improve surface quality in finishing passes. This geometry promotes stable chip formation and limits vibration, which translates into more predictable outcomes on the workpiece. The combination of the head’s compact Ø50 mm diameter and the specified cutting geometry makes the tool suitable where space is restricted but surface quality is critical. Bold construction and precise component fit maintain repeatability across multiple set-ups. Fast mounting and secure clamping minimise downtime Designed for efficient tool changes and secure attachment, the head mounts on a 22 mm arbor and is retained using the BK300 clamping wedge and an M8x18 locking screw, with an included Allen key size 4 for assembly. The lightweight construction (approx. 0.488 kg) simplifies handling during tool changes and reduces strain on the toolholder. Clear mechanical interfaces ensure repeatable concentricity and short set-up times, which supports higher machine utilisation and lower non-productive time on the shop floor. Purpose and practical benefits in finishing operations Intended for use with OFCR 0704 indexable inserts, the head delivers a balance of accessibility and cutting performance for finishing and light profiling work. The compact diameter allows access to confined features while maintaining a robust tool connection to the machine spindle. By standardising on an insert family, consumable management becomes simpler and costs can be controlled through predictable insert life and straightforward replacement. The result is a reliable milling solution that supports consistent production quality and easier process planning. For orders or technical advice regarding the Teknik Cutting Tools face milling head with 43° geometry, contact Metav Werkzeuge GmbH in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com for tailored delivery and support Technical data Article number: T260TM Name: Planmesserkopf For: OFCR 0704 indexable inserts Core technical data Diameter: 50 mm Overall length: 45 mm Mounting bore: 22 mm Weight: 0.488 kg Cutting angle: 43° Cutting edges: 4 Special features Clamping wedge: BK300 Locking screw: M8x18 Allen key: 4 Suitable for OFCR 0704 inserts Manufacturer: Teknik Makina FAQ Is this head compatible with OFCR 0704 indexable inserts? Yes. The Planmesserkopf T260TM is designed specifically for use with OFCR 0704 indexable inserts and the geometry is optimised for that insert form. What arbor size is required for mounting? The tool requires a 22 mm mounting bore and is intended to be secured using the BK300 clamping wedge arrangement for reliable concentricity. How many cutting edges does the head support? The head accommodates four cutting edges, enabling uninterrupted finishing passes with predictable surface results. What is the cutting angle and how does it affect machining? The 43° cutting angle reduces cutting forces and improves surface finish in light finishing applications, providing steadier chip evacuation and reduced tool-induced vibration. Which fastening parts are delivered or required for installation? The head uses an M8x18 locking screw and an Allen key size 4 for fastening; the BK300 clamping wedge is the recommended clamping component. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the compact yet robust face milling solution: a Ø50 mm head with a 75° cutting angle and compatibility with SPKN 1203 indexable inserts, delivering stable cutting and straightforward insert changes; order directly via Metav Werkzeuge or consult our team for configuration advice. Planmesserkopf – face milling head for SPKN 1203 indexable inserts, Ø50 mm, 3 cutting edges | Teknik Makina The Planmesserkopf is a compact face milling head designed for precision machining with SPKN 1203 indexable inserts, suited to small and medium-sized machine tools where stability and quick tool change are essential Compact Ø50 head for tight set-ups Accepts SPKN 1203 indexable inserts 75° cutting angle for stable cutting Consistent performance for productive machining The milling head is engineered to provide stable cutting and repeatable results in production runs. With a 75° cutting angle, the design reduces chatter and spreads cutting forces across the insert edge, which supports improved surface finish and longer tool life. The use of standard SPKN 1203 indexable inserts means straightforward regrind or replacement cycles and flexible grade selection for different workpiece materials. This technical setup leads to measurable efficiency gains and predictable process windows on the shop floor. Fast insert changes and secure clamping for high uptime Maintenance and tool changes are kept simple: the insert is secured with an M8x24 clamping screw tightened with a 5 mm Allen key, allowing quick exchange without special tools. The head features a 22 mm mounting diameter for rigid seating in the tool post or arbor, and a balanced geometry across 3 cutting edges to maintain cutting stability. At 0.385 kg and an overall length of 45 mm, the component is light enough for agile handling yet sufficiently robust for repeatable clamping, reducing machine downtime and keeping production moving. Compact design that suits constrained setups A small footprint and a Ø50 mm body make this cutter head particularly useful for restricted working spaces or multi-spindle configurations where clearance is limited. The compact form factor, combined with a proven insert system, delivers practical benefits: easier tool storage, lower inertial loads on spindle bearings and simpler toolpath planning. For workshops seeking a reliable, easy-to-fit solution, the head offers a balance of rigidity and accessibility that supports both one-off jobs and longer batch runs. For technical purchasing and delivery from Emmerich, request the Teknik Makina face milling head via Metav Werkzeuge (info@metav-werkzeuge.com | +49 2822 7131930) for personalised advice and procurement options Technical Data Article number: T148TM Manufacturer: Teknik Makina Facts Diameter: 50 mm Cutting edges: 3 Overall length: 45 mm Weight: 0.385 kg Shank diameter: 22 mm Cutting angle: 75° Special features Compatible with SPKN 1203 indexable inserts Clamping screw: M8x24 Allen key size: 5 mm FAQ What insert type does this head accept? The face milling head accepts SPKN 1203 indexable inserts; insert grade choice determines the suitable workpiece materials and cutting conditions. How are the inserts secured? Inserts are clamped with an M8x24 screw tightened using a 5 mm Allen key, providing secure fixation for stable cutting. What are the key dimensions and weight? Diameter 50 mm, shank/mount diameter 22 mm, overall length 45 mm, weight 0.385 kg for the Teknik Makina face milling head (SKU T148TM). Is the head suitable for machines with limited clearance? Yes — the compact Ø50 mm body and short overall length make it suitable for constrained set-ups and multi-tool arrangements. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 45° cutting geometry, compact 50 mm diameter and secure 22 mm mounting bore for consistent facing results; combine high mechanical quality with quick clamp-and-change handling to keep setups short. Order the milling head directly via Metav Werkzeuge or consult the team for availability and application advice. Planmesserkopf T164TM — 45° face-milling head for SNEU 1204 indexable inserts (Teknik Makina) A robust Planmesserkopf T164TM built for 45° facing applications with SNEU 1204 indexable inserts, optimised for secure mounting and efficient changeover. 45° cutting geometry for precise facing Compatible with SNEU 1204 indexable inserts 22 mm mounting bore for secure fitting Torx M5x12 screw with T20 key for quick service Improved material removal and surface quality with a 45° geometry The 45° cutting angle delivers a balance between material removal rate and surface finish, enabling effective facing without excessive tool load. Fitted for SNEU 1204 indexable inserts, the head spreads cutting forces over multiple edges, which reduces vibration and helps maintain consistent surface tolerances. With a compact 50 mm diameter, the assembly suits constrained fixtures while still providing a reliable contact circumference for stable machining. The engineering focus is on process stability and reproducible results rather than speculative performance figures. Fast, repeatable clamping and serviceability for shop-floor efficiency Mounting and service are simplified by a 22 mm shank interface and a single M5x12 Torx fastening screw, compatible with a T20 key. This arrangement ensures secure clamping and straightforward indexable-insert replacement, reducing downtime during insert changes. The unit’s overall length of 40 mm and modest mass (approx. 0.447 kg) allow for compact tool stacks and minimal spindle overhang, aiding in rigidity and repeatability on automated or manual lathes and milling heads. Designed for reliable integration into workshop workflows Engineered metalworking quality and a clear spare-part interface mean the head supports systematic tool management in production environments. The head’s configuration with five cutting edges permits predictable cutting cycles and simplifies inventory control where SNEU 1204 inserts are standardised. Documentation and the proven mechanical layout make the component straightforward to specify for fixture design and tool-presetting routines, supporting shorter setup times and higher first-pass yield. Contact Metav Werkzeuge today for availability and tailored application advice on the Teknik Cutting Tools T164TM face-milling head, with stock and dispatch direct from the Emmerich facility Technical data Article number: T164TM Brand: Teknik Makina Type: Face-milling head, 45° Dimensions & weight Diameter: 50 mm Overall length: 40 mm Mounting bore: 22 mm Weight: 0.447 kg Cutting angle: 45° Cutting edges: 5 Special features Compatible with SNEU 1204 indexable inserts Torx screw M5x12 Torx key size T20 SKU: T164TM FAQ Which indexable inserts fit this milling head? The milling head is compatible with SNEU 1204 indexable inserts as specified for the Planmesserkopf T164TM. What is the mounting interface for the cutter head? The head uses a 22 mm mounting bore and is secured with an M5x12 Torx screw, tightened using a T20 key. How does the 45° cutting angle affect machining? A 45° geometry reduces cutting load peaks and improves surface finish compared with steeper angles, supporting stable facing and consistent tolerances. Is the head suitable for compact setups and short overhangs? Yes, the compact 50 mm diameter and 40 mm overall length are designed to limit overhang and maintain rigidity in constrained setups. What is the article number for ordering and referencing? The article number for ordering and technical reference is T164TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a 100° cutting angle, compatibility with YG-1 ENMX 0905 indexable inserts and a compact Ø50 mm head for stable face milling and efficient insert changes; order the unit directly via Metav Werkzeuge or ask our consultants for application support. Planmesserkopf T701TM — face milling head with 100° cutting angle (Teknik Makina) The Planmesserkopf T701TM is a 100° face milling head designed for use with ENMX 0905 indexable inserts, delivering stable engagement for general face milling and finishing operations Compatible with YG-1 ENMX 0905 inserts 100° cutting angle for robust engagement Ø50 mm head diameter Four cutting edges for continuous machining 22 mm mounting for standard toolholders Improved cutting stability through geometry and edge count The head’s 100° cutting angle and its four cutting edges combine to reduce vibration during engagement, which improves surface finish and extends insert life. A larger effective cutting angle often spreads cutting forces across multiple edges, so each pass imposes less stress on the insert. For workshops unfamiliar with cutting geometry, this means fewer tool changes and more predictable cycle times, helping to keep production steady and downtime low. The compact Ø50 mm head diameter supports tight set-ups while still delivering consistent material removal. Fast insert changes and broad compatibility for workflow efficiency Designed for ENMX 0905 indexable inserts from YG-1, the reducer simplifies tooling logistics by matching a widely used insert format. Insert replacement and clamping use a Torx T10 drive with an M3.5x8.5 fixing screw, making routine maintenance straightforward with common workshop tools. Indexable inserts allow damaged cutting edges to be rotated or replaced without removing the entire head, cutting maintenance time and lowering consumable costs. This configuration supports rapid recovery after wear and keeps machine uptime high. Reliable mounting and concise dimensions for predictable set-up The tool mounts on a 22 mm shank interface and has a 50 mm overall height, enabling simple integration into standard toolholders and predictable stick-out calculations. Stable mounting reduces chatter and assists in maintaining repeatable cutting conditions across batches. Supplied by Teknik Makina, the component is suitable for general face milling tasks where compatibility and quick serviceability are priorities, and it helps workshops consolidate tooling choices without sacrificing process reliability. For procurement or technical advice on Teknik Makina’s 100° face milling head (T701TM), contact Metav Werkzeuge in Emmerich for specification matching and secure supply – info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: T701TM Manufacturer: Teknik Makina Compatible inserts: ENMX 0905 (YG-1) Core specifications Head diameter: 50 mm Overall height: 50 mm Shank mounting diameter: 22 mm Cutting edges: 4 Cutting angle: 100° Special features Torx key: T10 Fixing screw: M3.5x8.5 Designed for YG-1 ENMX 0905 indexable inserts FAQ Which indexable inserts fit this milling head? The T701TM is designed for ENMX 0905 indexable inserts and is compatible with the YG-1 range for straightforward sourcing and replacement. How many cutting edges does the head provide? The face milling head features four cutting edges, enabling continuous machining and even wear distribution for longer insert life. What is the mounting diameter for toolholder compatibility? The tool uses a 22 mm shank mounting interface for integration with standard toolholders. Which fasteners are required for insert replacement? Insert clamping is secured with an M3.5x8.5 screw tightened using a Torx T10, allowing quick and reliable changes with common workshop tools. For which machining tasks is this head best suited? With its 100° cutting angle and compact Ø50 mm diameter, the head is ideal for stable face milling and finishing where predictable surface quality and efficient insert changes are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact 50 mm diameter head, sturdy 22 mm mounting and seven cutting edges for stable, high-quality face milling — order the face-milling cutter head directly via Metav Werkzeuge or contact our consultants for tailored advice. Face-milling cutter head T481TM — 50 mm diameter, 7 cutting edges — Teknik Makina The face-milling cutter head T481TM is engineered for use with BLMP 0603 indexable inserts and designed to deliver consistent face-milling and finishing performance in small to medium-sized setups 50 mm diameter for compact machining 7 cutting edges for smooth finishing 22 mm shank for stable mounting Compatible with BLMP 0603 inserts (Taegutec) Compact design for stable, repeatable machining The cutter head’s compact 50 mm diameter and 22 mm mounting diameter provide a small running envelope that reduces vibration and increases concentricity at speed. With a mass of 0.457 kg, the head is light enough for machines with limited spindle capacity yet rigid enough to maintain cutting stability. These dimensional properties translate directly into improved surface quality and predictable tool life, so machining cycles remain consistent and setups require fewer compensations. Secure clamping and fast insert changes to keep production moving Clamping is handled by an M3x6.5 Torx screw tightened with a T8 key, ensuring reliable seat pressure and minimal micro-movement of the insert during cutting. The system is compatible with BLMP 0603 indexable inserts and tested for use with Taegutec grades, enabling quick insert replacement and consistent chip control. Reduced changeover time means less downtime on the shopfloor and higher net productive hours per shift. Optimised cutting geometry for quality finishes An effective 100° cutting angle combined with seven cutting edges spreads the cutting load and reduces edge wear per pass. The geometry supports fine finishing operations by directing chips away from the cut and lowering impact on each edge, which helps to achieve a more uniform surface finish and fewer rework cycles. Explaining the geometry in plain terms: a larger approach angle softens the engagement, producing gentler cutting forces and better surface integrity. Workshop compatibility and supply reliability for uninterrupted work The head’s dimensions (50 mm diameter, 50 mm overall length, 22 mm mounting) make it suitable for compact toolholders and smaller milling spindles, providing flexibility across varied machine parks. Compatibility with standard BLMP 0603 inserts ensures straightforward stocking and replacement. Backed by Metav’s distribution from Emmerich — a European quality filter with a broad product range and reliable logistics — the component supports uninterrupted workflows and simplified procurement for workshops and specialist suppliers. For reliable face-milling performance from Teknik Makina, request a quote or technical clarification via Metav Werkzeuge — contact our consultants at info@metav-werkzeuge.com or call +49 2822 7131930 to confirm suitability for the intended application Technical data SKU: T481TM Manufacturer: Teknik Makina Product: Face-milling cutter head for indexable inserts Suitable for inserts: BLMP 0603 Compatible inserts manufacturer: Taegutec Torx screw: M3x6.5 Torx key: T8 Facts Diameter: 50 mm Shank / mounting diameter: 22 mm Weight: 0.457 kg Number of cutting edges: 7 Cutting angle: 100° Overall length: 50 mm Special features For BLMP 0603 indexable inserts Tested compatibility with Taegutec inserts Compact form factor for small spindles Secure Torx clamping system M3x6.5 / T8 FAQ What insert type is required for this cutter head? The face-milling cutter head accepts BLMP 0603 indexable inserts; compatibility with Taegutec grades is specified for consistent performance. Which toolholder or shank size is needed for mounting? Mounting requires a toolholder compatible with a 22 mm shank/mounting diameter as stated in the technical data. How is the insert secured in the cutter head? Insert clamping is achieved with an M3x6.5 Torx screw and a T8 key for reliable, repeatable seating. What operations is the head best suited to? The head is designed for face milling and finishing passes where a 100° approach and multiple cutting edges favour smooth surfaces and reduced edge wear. How many cutting edges are available and why does that matter? The head uses seven cutting edges, which helps distribute wear and maintain consistent cutting forces for improved surface finish and longer intervals between insert changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact design with a 50 mm diameter and integrated internal coolant for efficient chip evacuation, while compatibility with LNMU 0303 indexable inserts provides application flexibility; order the face-milling head directly via Metav Werkzeuge or ask our consultants if needed. Face-milling head for LNMU 0303 indexable inserts — 50 mm, internal coolant by Teknik Makina Face-milling head for LNMU 0303 indexable inserts designed for compact, coolant-fed face milling and finishing in small to medium workpieces. 50 mm diameter for compact face milling Internal coolant for improved chip control Compatible with LNMU 0303 inserts T8 Torx fixation, M2.5x7 screws Faster, cleaner cuts for high-throughput machining The face-milling head delivers efficient material removal through its optimised geometry: 7 cutting edges and a 55° cutting angle combine to reduce cutting forces and distribute wear over multiple edges. This setup permits steadier feeds and feeds higher material removal rates without sacrificing surface finish. For operators seeking productivity gains, the reduced vibration and balanced design translate into shorter cycle times and more consistent part quality. Straightforward mounting and broad insert compatibility Mounting is simplified by the T8 Torx fixation and supplied M2.5x7 screws, which ensure secure clamping of the insert seats and quick index changes. The head is specified for LNMU 0303 inserts and is compatible with insert manufacturers such as Tungaloy and OKE, offering flexibility in tooling choice. Clear reference to the insert type avoids confusion during procurement and makes setup reproducible across different machines. Improved tool life and process reliability with coolant feed Integrated internal coolant supplies cutting fluid directly to the cutting zone to aid chip evacuation and thermal control. This results in lower flank wear and extended insert life, especially under interrupted cuts or challenging materials. The head’s modest mass (approx. 0.541 kg) supports dynamic stability on smaller toolholders and helps maintain balance at higher spindle speeds, contributing to predictable tool behaviour and reduced setup waste. Ideal for precise face milling and finishing tasks Designed for workshops and production environments that require compact, accurate face-milling solutions, this cutter head excels in finishing and light stock removal on small diameters. The combination of a small footprint, coolant delivery and multi-edge indexing provides a practical solution for jobs requiring good surface quality and repeatability. The compact design is also beneficial where toolchanging space is limited, enabling efficient tooling layouts and faster changeovers. Contact Metav Werkzeuge for a tailored quote or technical advice on the Teknik Makina face-milling head with internal coolant and compatibility for LNMU 0303 inserts — fast supply from Emmerich to your workshop. Technical Data Article number: T729-1TM SKU: T729-1TM Brand: Teknik Makina Description: Face-milling head for LNMU 0303 indexable inserts Label: 50mm Planmesserkopf LNMU 0303 L50mm mit Innenkühlung Facts Diameter: 50 mm Overall length: 50 mm Weight: 0.541 kg Cutting edges: 7 Cutting angle: 55° Torx key: T8 Torx screw: M2.5x7 eCl@ss: 21181015 Internal coolant: yes Special features Suited for LNMU 0303 indexable inserts Compatible with Tungaloy and OKE inserts Indexable-insert system for economical regrind Compact face-milling format FAQ Which insert type fits this head? The head accepts LNMU 0303 indexable inserts; compatible insert brands include Tungaloy and OKE, offering flexible sourcing. Is the cutter head coolant-fed? Yes, the face-milling head features internal coolant, delivering fluid to the cutting zone for improved chip control and tool life. What is the fixing method for the inserts? Inserts are secured using a T8 Torx fixation with M2.5x7 screws for reliable clamping and easy index changes. Can it be used for finishing operations? The compact geometry and 55° cutting angle make the head well suited to finishing and light stock removal where surface quality is important. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a compact 50 mm diameter with internal coolant and six cutting edges, this face milling head offers reliable surface finish and extended tool life for medium-duty milling operations; order the component directly via Metav Werkzeuge or contact our consultants for application matching. Planmesserkopf — face milling head, 50 mm diameter and internal coolant (Teknik Makina) The Planmesserkopf is a compact face milling head engineered for precision face machining with LNMX 1004 indexable inserts, providing a balance of rigidity and accessibility in confined setups. 50 mm diameter for stable face milling Internal coolant supply for better cooling Holds LNMX 1004 indexable inserts (Korloy) Six cutting edges; 90° cutting angle Consistent surface quality with efficient material removal The compact 50 mm diameter and six cutting edges deliver predictable cutting engagement for stable roughing and finishing passes. By combining a short overall length with a robust body, the head minimises vibration and facilitates a consistent surface finish even in interrupted cuts. The 90° cutting angle concentrates the cutting forces for controlled chip formation, which translates into higher process reliability and reduced rework rates in production runs. Better cooling and longer tool life through internal coolant Equipped with internal coolant, the milling head directs fluid straight to the cutting zone to reduce temperature peaks and flush chips away from the insert pockets. This focused cooling reduces thermal wear on the insert geometry and helps maintain cutting-edge integrity over longer tool life. For workshops seeking predictable maintenance intervals, the improved cooling leads to fewer unscheduled stoppages and a lower total cost per component machined. Fast servicing and straightforward assembly for shop floors Maintenance and insert changes are simplified: the head uses a T15 Torx key and M4x10 Torx screw, enabling quick clamp releases with standard workshop tooling. The compact construction and clear fastening method shorten downtime for insert changes and routine inspections. The modest weight of 0.26 kg and overall length of 40 mm make handling and set-up faster, benefiting busy shops where changeover speed matters. Compatibility and application scope for reliable integration Specifically designed for LNMX 1004 indexable inserts and compatible with inserts from Korloy, the head fits into established tooling systems without requiring bespoke inserts. This compatibility supports inventory simplification and streamlines procurement. The design suits general face milling tasks on milling machines and machining centres where a robust, coolant-fed solution improves throughput and repeatability. For a tailored recommendation or to procure the Teknik Makina face milling head through Metav Werkzeuge, please contact our advisors for specification matching and delivery options Technical Data SKU: T506TM Manufacturer: Teknik Makina Product type: Face milling head Facts Diameter: 50 mm Overall length: 40 mm Weight: 0.26 kg Number of cutting edges: 6 Cutting angle: 90° ECLASS: 21181015 Special features Internal coolant supply For LNMX 1004 indexable inserts Compatible with Korloy inserts Torx key: T15 Torx screw: M4x10 FAQ Which indexable inserts fit this milling head? The head accepts LNMX 1004 indexable inserts; compatibility with Korloy-manufactured inserts is indicated for smooth integration into existing tool stocks. Does the head provide coolant to the cutting zone? Yes, the internal coolant feed supplies fluid directly to the insert cutting edge, improving cooling and chip evacuation during machining. What fastening hardware is required for insert clamping? Insert clamping uses a T15 Torx key and M4x10 Torx screw, allowing quick, standardised servicing on the shop floor. Is this head suitable for finishing and roughing? The combination of a 50 mm diameter, six cutting edges and a 90° cutting angle makes the head suitable for both finishing and medium-duty roughing face milling operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of 50 mm diameter, internal coolant and compatibility with LOGU 0303 indexable inserts for stable face milling and prolonged insert life — ideal for repeatable production tasks. Order the tool directly via Metav Werkzeuge or consult our specialists for application-specific advice. Face milling head T732-1TM — 50 mm, internal coolant, for LOGU 0303 indexable inserts (Teknik Makina) Face milling head T732-1TM designed for efficient face milling operations with LOGU 0303 indexable inserts, combining compact dimensions with coolant integration for reduced thermal distortion in series production. Compact 50 mm diameter for tight workspaces Integrated internal coolant for temperature control Compatible with LOGU 0303 indexable inserts Seven cutting positions for steady material removal Consistent metal removal from a compact tool body The compact design centres on a 50 mm diameter and a total length of 50 mm, providing a small footprint without compromising stability. The short overhang reduces vibration and improves surface finish, which is particularly advantageous in high-repeatability environments. By pairing the head with LOGU 0303 indexable inserts, shops gain a versatile cutting solution that supports consistent cycle times and simplified tool inventory management. The balanced geometry contributes to predictable tool life and reliable process repeatability. Coolant integration that protects inserts and workpieces Built-in internal coolant directs cutting fluid close to the cutting zone, assisting chip evacuation and reducing thermal load on the cutting edge. This targeted cooling helps maintain cutting-edge geometry and reduces heat-related wear, translating into longer intervals between indexings. For teams unfamiliar with the benefits, internal coolant means fewer scrap parts from thermal distortion and improved dimensional stability across batches — a clear operational advantage for production milling. Quick mounting and reliable clamping for minimal downtime The head accepts assembly via the provided M3x7 Torx screws and requires a T8 Torx key for secure fastening. A shank diameter of 22 mm ensures rigid connection to compatible toolholders and reduces run-out risk during rotation. At a weight of 0.582 kg, the unit is robust yet manageable during tool changes, helping to keep set-up times short. The seven possible cutting positions support straightforward index changes, reducing maintenance effort on the shop floor. Engineered for industrial compatibility and efficient sourcing Compatibility with inserts from Kyocera (LOGU 0303) simplifies procurement and ensures access to a wide range of grades and geometries for different materials. The design focuses on practical workshop requirements: compact dimensions for tight fixture layouts, coolant provision for high-performance milling, and standardised fasteners for maintenance efficiency. For procurement and production planners, the result is a tool that integrates cleanly into existing processes while offering measurable improvements in uptime. For reliable supply of Teknik Makina’s face milling head with internal coolant and LOGU 0303 compatibility, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and delivery options Technical data Article number / SKU: T732-1TM Manufacturer: Teknik Makina Product type: Face milling head Core measurements Diameter: 50 mm Total length: 50 mm Shank diameter: 22 mm Weight: 0.582 kg Number of cutting positions: 7 Torx key: T8 Torx screw: M3x7 eClass: 21181015 Features and compatibility Internal coolant integrated Suitable for LOGU 0303 indexable inserts Compatible insert manufacturer: Kyocera Compact design for reduced overhang Standardised fastening for quick servicing FAQ Is this head compatible with other insert systems? The face milling head is designed for LOGU 0303 indexable inserts; compatibility with other systems depends on matching insert geometry and seat geometry, so use LOGU 0303 or confirmed equivalents from Kyocera. How does internal coolant improve performance? Internal coolant aboard the T732-1TM delivers fluid directly to the cutting zone to aid chip evacuation, reduce heat at the cutting edge and extend insert life under continuous production. What key is required to service the screws? Servicing requires a T8 Torx key to tighten or remove the M3x7 Torx screws used for clamping the inserts and securing the head. Can the head be used in tight fixture layouts? Yes — the compact 50 mm diameter and 50 mm overall length make the head suitable for constrained setups where minimal overhang and stiffness are required. Who supplies and distributes this tool? Teknik Makina manufactures the head, and Metav Werkzeuge coordinates distribution and support in Europe, ensuring reliable availability and application advice. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high-stability design that combines a 50 mm diameter footprint with internal coolant to improve chip evacuation and extend insert life; compatibility with SDMT 09T3 indexable inserts ensures straightforward integration into existing tool sets. Order the head directly via Metav Werkzeuge or contact our consultants for application guidance. Face milling head T363-1TM – 50 mm diameter, internal coolant (Teknik Makina) The face milling head T363-1TM is a compact, coolant-fed cutter head designed for efficient face milling with SDMT 09T3 indexable inserts in medium- to high-precision machining operations. 50 mm diameter for compact setups Internal coolant for improved chip evacuation Five cutting edges for balanced cutting Compatible with SDMT 09T3 inserts (ZCC) Compact 40 mm overall length for stability Performance gains from a compact, coolant-fed design The combination of a 50 mm diameter and a 40 mm overall length delivers a low overhang solution that improves rigidity and reduces vibration during face milling. With internal coolant channels, the head maintains better thermal control at the cutting zone, which in turn contributes to longer insert life and more consistent surface finishes. The compact dimensions make this milling head particularly suitable where limited tool clearance or tight fixturing is a concern, helping to shorten cycle times through improved stability. Simple maintenance and proven insert compatibility Maintenance and insert changes are straightforward: the head accepts SDMT 09T3 indexable inserts and is specified as suitable for ZCC insert types, enabling economical replacement strategies and compatibility with widely available tooling. Fast, tool-life-extending routines are supported by the standard Torx retention hardware: Torx T15 key and M3.5x8.5 screw, which simplify clamping and reduce downtime during tool changes. Indexable inserts mean that cutting geometry is recoverable without full tool replacement, lowering operating costs over time. Stability, balance and predictable results in production Equipped with five cutting edges, the head offers a balanced cutting profile that reduces chatter and distributes cutting forces evenly across the tool body. The modest mass of 0.355 kg contributes to dynamic stability and makes balancing on high-speed spindles less burdensome. For operations where repeatable tolerances and surface quality are priorities, the design supports reliable performance across batches and set-ups, translating into fewer reworks and higher first-pass yields. Ideal applications and who benefits most This face milling head is aimed at machine shops, maintenance departments and production lines looking to consolidate tooling with a compact, coolant-capable cutter. Its specification suits operations that require accessible, rigid tooling for general face milling tasks while maintaining compatibility with standard SDMT 09T3 inserts. Supplied via an experienced distributor network, the tool integrates into established workflows with minimal adjustment to existing clamping and insert inventories. For application checks, tooling recommendations or order placement, contact Metav Werkzeuge in Emmerich for tailored advice and dependable supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: T363-1TM ECLASS: 21181015 Product: Face milling head Label: 50mm Planmesserkopf SDMT 09T3 L40mm mit Innenkühlung Facts Diameter: 50 mm Overall length: 40 mm Weight: 0.355 kg Cutting edges: 5 Torx key: T15 Torx screw: M3.5x8.5 Internal coolant: yes Special features Compatible with SDMT 09T3 indexable inserts Insert manufacturer suitability: ZCC Manufacturer: Teknik Makina FAQ Is the head compatible with standard SDMT 09T3 inserts? Yes. The face milling head accepts SDMT 09T3 indexable inserts and is specified as suitable for inserts from ZCC, ensuring interchangeability with common insert stocks. Does the cutter head provide internal coolant? Yes. Internal coolant channels are integrated to improve chip evacuation and reduce cutting-zone temperatures, which helps to prolong insert life. Which fastening hardware is required for insert clamping? The head uses Torx retention: M3.5x8.5 screws secured with a T15 Torx key for straightforward insert changes and repeatable clamping torque. How many cutting edges does the head support and what is the effect? The head features five cutting edges, providing a balanced cutting profile that reduces vibration and contributes to a stable cutting process and improved surface finish. What are the key dimensions for machine integration? Key dimensions are 50 mm diameter and 40 mm overall length, with a mass of 0.355 kg, making the head suitable for compact set-ups and machines with limited tool overhang. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Compact 50 mm face milling head with internal coolant and four cutting edges provides reliable finishing with simple insert changes; order the face mill directly via Metav Werkzeuge or contact our consultants for application advice. Face milling head T358-1TM — 50 mm diameter, internal coolant (Teknik Makina) Face milling head T358-1TM is a compact tool for efficient finishing with SDMT 1204 indexable inserts, designed for space‑constrained setups and frequent insert changes Face milling head for SDMT 1204 inserts 50 mm diameter for compact setups Internal coolant for improved chip evacuation Four cutting edges, Torx T15 screws Accurate finishing in tight spaces for consistent results The compact design with a 50 mm diameter ensures stable engagement and predictable cutting forces when working on small‑scale faces. Built for use with SDMT 1204 indexable inserts, this head delivers a balance between accessibility and rigidity that supports uniform surface quality. The lightweight construction (approx. 0.312 kg) reduces spindle load in sensitive setups while the short 40 mm overall length helps to keep overhang minimal, which in turn lowers the risk of chatter and dimensional deviation. Engineers benefit from straightforward integration into existing toolholders and predictable process behaviour that supports repeatable batch production. Cooler cuts and longer insert life through directed coolant Internal coolant channels feed cutting zones directly, improving lubrication and chip evacuation during interrupted or continuous milling. The internal coolant reduces thermal peaks at the cutting edge, which slows wear and helps maintain tool geometry for longer intervals between indexings. Combined with secure fastenings — Torx T15 drive and M4x10 screws — the system provides stable clamp force that minimises micro‑movement under load. The practical result is enhanced productivity and fewer unscheduled stops, making the head an effective choice when stability and uptime are priorities in series manufacturing. Fast servicing and reliable clamp for smooth shopfloor routines The use of SDMT‑type indexable inserts means insert replacement is quick and does not require regrinding, so maintenance routines are compact and predictable. The head is fitted with four cutting edges, supporting uninterrupted rotation and even wear distribution across inserts; this reduces total tooling costs per component when set into an optimised tool cycle. Assembly and disassembly are handled with a common Torx T15 key, streamlining maintenance procedures and allowing trained staff to perform swaps rapidly. For workshops seeking a dependable, low‑complexity milling head, the combination of compact geometry and direct coolant creates measurable time savings on recurring tasks. Contact Metav Werkzeuge today to discuss how the Teknik Makina face milling head T358-1TM can be integrated into existing processes — technical advice and ordering information available via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data SKU: T358-1TM Product type: Face milling head Brand: Teknik Makina Description: for SDMT 1204 indexable inserts Label: 50mm Planmesserkopf SDMT 1204 L40mm mit Innenkühlung Core specifications Diameter: 50 mm Shank diameter: 22 mm Overall length: 40 mm Weight: 0.312 kg Cutting edges: 4 Cutting angle: 45° Drive: Torx T15 Fastening screws: M4x10 ECLASS: 21181015 Features / Compatibility Internal coolant Compatible with SDMT 1204 indexable inserts Suitable for ZCC insert manufacturer Compact design for reduced overhang Quick insert change via Torx fastening FAQ What inserts fit this face milling head? The face milling head accepts SDMT 1204 indexable inserts; it is also specified as compatible with inserts from ZCC. Does the tool provide coolant to the cutting edge? Yes, the head features internal coolant channels that deliver fluid directly to the cutting zone to aid chip evacuation and reduce thermal wear. Which fastening hardware is used for the inserts? Inserts are secured with Torx T15 drive screws; the specified screw size is M4x10 for reliable clamping. Is the head suitable for compact or heavy setups? The compact 50 mm diameter and 40 mm length make the head especially suitable for space‑limited or light to medium‑duty milling operations where reduced overhang is an advantage. Manufacturer/Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of compact design, internal coolant and proven compatibility with SEET 12T3 indexable inserts for reliable facing operations; order directly via Metav Werkzeuge or consult our specialists for technical advice. Face milling head — 50 mm diameter, internal coolant (Teknik Makina) The face milling head for SEET 12T3 indexable inserts is designed for precision facing and finishing tasks in production and maintenance workshops. 50 mm diameter for compact facing Internal coolant reduces heat build-up Compatible with SEET 12T3 indexable inserts Torx T15 / M3.5 x 11 fastening High material removal with stable surface finish This compact cutter offers a 50 mm diameter and a 45° cutting angle that combine to reduce radial cutting forces and help achieve an even surface finish on the workpiece. With 4 cutting edges, the head enables short, repeatable tool changes and predictable machining cycles, which supports higher throughput in both small-batch and continuous production. The geometry is optimised to balance chip evacuation and contact area, helping to prolong insert life while maintaining consistent dimensional results. Secure clamping and straightforward maintenance The tool uses standardised inserts and a robust fastening system that relies on M3.5 x 11 mm Torx screws and a T15 Torx interface, allowing repeatable clamp torque and simple servicing. The moderate overall length (L40 mm) and a 22 mm mounting diameter support stable toolholding in common toolholders, reducing vibration and improving repeatability. Quick, tool‑centric maintenance routines minimise downtime and make the cutter suitable for workshops aiming to keep changeover times low. Integrated cooling and production reliability A built‑in internal coolant channel directs coolant close to the cutting edge, improving temperature control and chip flushing during heavy facing cuts. The low mass (0.345 kg) and compact form support dynamic machining where balance and stiffness matter. Delivered as a ready‑to‑fit head, this item (SKU T560-1TM) is especially suitable where standard SEET 12T3 inserts are already in use, enabling inventory rationalisation and faster spare‑part turnover. For supply and technical consultation on Teknik Makina face milling heads with internal coolant, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for prompt advice and reliable delivery. Technical data SKU: T560-1TM Label: 50mm Planmesserkopf SEET 12T3 L40mm Product type: Planmesserkopf Manufacturer: Teknik Makina Facts Shank diameter: 22 mm Diameter: 50 mm Overall length: 40 mm Weight: 0.345 kg Number of cutting edges: 4 Cutting angle: 45° Special features Internal coolant Compatible with SEET 12T3 indexable inserts Torx screw: M3.5 x 11 mm Torx key: T15 SKU: T560-1TM FAQ Which inserts fit this milling head? The head is designed for SEET 12T3 indexable inserts; using the specified insert type ensures correct seat seating and cutting geometry for reliable performance. Does the cutter provide internal coolant? Yes, this face milling head includes internal coolant, which supplies cutting fluid directly to the tool‑work zone to aid cooling and chip evacuation. What are the main mounting dimensions? The tool features a shank diameter of 22 mm, an overall length of 40 mm and a cutter diameter of 50 mm, suitable for compact facing setups. How many cutting edges are available per head and what is the cutting angle? The assembly provides 4 cutting edges and is set up with a 45° cutting angle, balancing cutting forces and surface finish. Which fasteners and tools are required for insert retention? Insert clamping uses M3.5 x 11 mm Torx screws and a T15 Torx key for consistent clamp torque and secure fastening. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise, compact face milling with internal coolant and compatibility with SNEU 1206 indexable inserts; order directly via Metav Werkzeuge or consult our specialists for application-specific advice. Face milling head – 50 mm, internal coolant (Teknik Makina) Face milling head for efficient face milling operations with SNEU 1206 indexable inserts, designed for compact setups and robust chip control. 50 mm diameter for compact face milling head Internal coolant for improved chip evacuation Compatible with SNEU 1206 indexable inserts Torx T20 screws (M5x12) for secure fixing Compact design for stable, accurate face milling The compact 50 mm diameter and 40 mm overall length create a low-profile toolholder that reduces overhang and enhances rigidity. With a maximum cutting diameter of 63 mm and a 45° cutting angle, this tool produces clean face finishes while maintaining process stability. The light weight of 0.447 kg minimises spindle load for faster acceleration and deceleration, which is particularly beneficial in small to medium-sized machining centres. These dimensional and geometric specifications translate directly into improved surface quality and repeatable machining cycles. Internal coolant and secure clamping for longer tool life Equipped with internal coolant, this head directs cutting fluid precisely to the cutting edges, improving lubrication and chip evacuation. That targeted cooling reduces thermal stress on the inserts, extending cutting life and maintaining cutting edge geometry. Fixing is achieved with Torx T20 screws (M5x12), offering a robust and repeatable clamping method that simplifies insert changes while ensuring safe seating under intermittent loads. Compatibility with Walter-type inserts (SNEU 1206) means replacement parts are widely available, supporting continuous production with minimal downtime. Workshop-friendly maintenance and straightforward integration Maintenance is straightforward thanks to standardised fastenings and a common insert format; insert changes and re-torquing require only a Torx T20 key. The head supports five cutting positions to balance material removal rates and tool life, making it suitable for both roughing and semi-finishing passes. Its compact form factor and standard interface make it a flexible choice for a wide range of industrial and trade workshop applications where space, reliability and consistent results are priorities. Choose the Teknik Makina face milling head for reliable, coolant-enhanced face milling—contact Metav Werkzeuge by email at info@metav-werkzeuge.com or call +49 2822 7131930 for ordering and technical advice Technical data SKU: T164-1TM Product type: Face milling head Brand: Teknik Makina Label: 50 mm face milling head SNEU 1206 L40 mm with internal coolant ECLASS: 21181015 Key measurements Diameter: 50 mm Overall length: 40 mm Max. cutting diameter: 63 mm Cutting angle: 45° Weight: 0.447 kg Number of cutting edges: 5 Features & compatibility Internal coolant Compatible with SNEU 1206 indexable inserts Suitable for inserts by Walter Torx screw: M5x12 Torx key: T20 FAQ What insert type does this face milling head accept? The face milling head accepts SNEU 1206 indexable inserts; it is designed for that insert geometry and seat. Is the tool suitable for installations with internal coolant requirements? Yes, the head features internal coolant, delivering coolant directly to the cutting zone to improve chip evacuation and tool life. Which fastening hardware is used for the inserts? Inserts are secured with M5x12 Torx screws tightened with a T20 Torx key for secure and repeatable clamping. What is the maximum cutting diameter achievable with this head? The maximum cutting diameter specified is 63 mm, allowing for effective face milling across a range of component sizes. Can this head be used with Walter inserts? The head is listed as compatible with inserts from Walter, supporting common workshop inventories for rapid replacement. How does the compact size benefit workshop operations? A compact diameter and short overhang reduce spindle load and increase rigidity, resulting in improved surface finish and more consistent machining cycles. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, durable solution that combines a 50 mm diameter, compatibility with SNMX 1206 indexable inserts and a five-edge seating for steady metal removal; order directly via Metav Werkzeuge or consult our specialists for application support. Face milling head T343TM — 50 mm, for SNMX 1206 indexable inserts (Teknik Makina) The face milling head for SNMX 1206 indexable inserts is a compact cutter head designed for reliable facing and light-duty milling tasks on turning and milling centres. *50 mm diameter for compact machining *Compatible with SNMX 1206 indexable inserts *Five cutting edges for stable material removal *Torx T15 drive with M4x12.5 screws Precision and dependable material removal for short-cycle production The compact 50 mm diameter and a total length of 40 mm provide a space-saving solution that maintains cutting stability in confined setups. Built for repeatable facing operations, the head is set up for SNMX 1206 inserts, which are seated to deliver consistent chip formation; this reduces vibration and supports predictable tool life. With five cutting edges, the arrangement increases contact points during engagement, so metal removal is more even and surface finish is improved. The combination of a short overall length and balanced geometry makes this cutter head particularly suitable for workshops and small-batch production where machine work envelopes are limited. Easy insert replacement and secure fastening for uninterrupted shifts Insert changes are simplified by the standard Torx T15 interface and M4x12.5 fixing screws, which allow fast, repeatable clamping without special tooling. The fastening is designed to be torque-stable, helping to prevent loosening during operation; screws are specified as M4x12.5 for reliable seat pressure. Compatibility with Korloy-branded SNMX 1206 inserts broadens the choice of cutting grades and coatings, enabling selection of grades for aluminium, steel or other materials as required. The head, weighing 0.348 kg, is light enough to reduce spindle load yet robust enough for steady cutting forces, so reloading cycles are efficient and downtime is minimised. Designed for integration and process reliability in production workflows Configured for standard indexable-insert tooling systems, the cutter head is straightforward to mount on compatible holders thanks to a 22 mm mounting bore, which is common in many modular systems. The specified 88° cutting angle gives near-flat facing capability, which is advantageous when achieving consistent surface planes is required. Constructed to be a pragmatic choice in mixed-production environments, the component prioritises predictable machining behaviour and easy maintenance. Where process stability and quick insert changes are paramount, this face milling head supports shorter cycle times and steady output quality. Contact Metav Werkzeuge for tailored application advice and to request a specification sheet or quotation for the Teknik Makina face milling head T343TM — our Emmerich team will assist with compatibility checks and delivery options Technical data Article number: T343TM Manufacturer: Teknik Makina Product type: Face milling head Label: 50mm Planmesserkopf SNMX 1206 L40mm ECLASS: 21181015 Core specifications Diameter: 50 mm Overall length: 40 mm Mounting bore: 22 mm Weight: 0.348 kg Number of cutting edges: 5 Cutting angle: 88° Torx drive: T15 Fixing screw: M4x12.5 Special features Compatible with SNMX 1206 indexable inserts Suitable for Korloy inserts Short design for confined machine envelopes Balanced geometry for steady cutting Light construction with robust clamping FAQ What inserts fit this cutter head? The Teknik Makina face milling head T343TM is designed for SNMX 1206 indexable inserts; compatibility with Korloy SNMX 1206 grades is specified. Which fixing screws and driver are required? Fastening is by M4x12.5 screws with a Torx T15 drive, providing secure and repeatable clamping for normal machining loads. Is the head suitable for confined work envelopes? Yes, the 50 mm diameter and 40 mm overall length make it suitable for compact setups and operations with limited clearance. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high‑precision solution that combines internal coolant for improved chip evacuation with compatibility for SOET 13 indexable inserts, ensuring consistent surface finishes and reduced tooling changes. Order directly via Metav Werkzeuge or consult the technical team for integration advice. Face milling cutter head T637-1TM by Teknik Makina — 50 mm, internal coolant, for SOET 13 inserts The face milling cutter head T637-1TM is a robust milling solution engineered for medium‑duty facing operations and designed to accept SOET 13 indexable inserts, offering reliable performance in production and maintenance environments. 50 mm diameter for compact machining Internal coolant for improved chip control Compatible with SOET 13 inserts by Palbit Four cutting edges for stable cutting Consistent metal removal with compact dimensions The 50 mm diameter cutter head offers a compact footprint while delivering efficient material removal thanks to its four cutting edges. The short overall length of 45 mm and a balanced geometry reduce vibration during facing operations, which promotes repeatable surface quality and extends insert life. For workshops where space and tool change frequency matter, the compact design contributes to shorter cycle times and more predictable production flow. Built‑in coolant for better chip control and tool life Equipped with internal coolant, the cutter head directs fluid close to the cutting zone to aid chip evacuation and reduce temperatures at the insert edge. This internal feed reduces thermal loading on the cutting edge and helps maintain a stable cutting process when machining a range of common engineering materials. The result is less edge wear and fewer unplanned insert changes, which positively affects overall tool costs and machine uptime. Secure fastening and straightforward maintenance Assembly and insert clamping rely on a Torx T15 interface and M3.5x8.5 screws, allowing controlled torque application for consistent clamping force. The tool accepts a 22 mm toolholder connection, ensuring compatibility with standard arbors and reducing the need for special adaptors. Routine maintenance is straightforward: inspect the insert seats, verify screw torque with a T15 key and replace inserts as required to keep cutting performance stable. Trusted compatibility and supply chain reliability Designed for SOET 13 indexable inserts and compatible with Palbit inserts, the tool integrates seamlessly into established insert inventories. Sourced from Teknik Makina and distributed via Metav Werkzeuge, the cutter head benefits from careful quality control and dependable stock management in Emmerich. This combination supports predictable lead times and the assurance of consistent product quality for industrial users and specialist workshops. For ordering details, tooling advice or to discuss integration with existing holders, contact Metav Werkzeuge — Manufacturer assistance and product supply are coordinated from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 to speak with a technical consultant. Technical data SKU: T637-1TM Product type: Face milling cutter head Manufacturer: Teknik Makina Diameter: 50 mm Shank diameter: 22 mm Overall length: 45 mm Weight: 0.318 kg Number of cutting edges: 4 Cutting angle: 90° Screw: M3.5x8.5 Torx key: T15 Internal coolant: yes Compatible inserts: SOET 13 Compatible insert manufacturer: Palbit Category: Planmesserkopf / Face milling cutter head FAQ Which inserts fit this cutter head? The face milling cutter head T637-1TM is designed for SOET 13 indexable inserts and is compatible with Palbit SOET 13 grades. Is the tool suitable for through‑coolant setups? Yes, the T637-1TM features internal coolant to feed fluid close to the cutting edge for improved chip evacuation. What toolholder connection does it require? The cutter head accepts a 22 mm shank connection, making it compatible with standard holders for compact facing tools. How many cutting edges are available per revolution? The tool is equipped with four cutting edges, delivering balanced engagement and steady material removal during facing passes. Which torque and screw type are used for insert clamping? Insert clamping uses Torx T15 screws with M3.5x8.5 fasteners; consistent torque application is recommended to ensure secure seating. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact yet robust milling solution that combines 50 mm diameter, internal coolant, and five cutting edges for consistent face milling. Order directly via Metav Werkzeuge or consult our specialists to ensure the tool fits the production setup. Face milling head for SOET 13 indexable inserts — Teknik Makina, 50 mm, internal coolant The face milling head for SOET 13 indexable inserts is a compact cutter head designed for efficient face milling in constrained setups, offering secure clamping and coolant-fed cutting zones for improved tool life. 50 mm diameter for compact milling Internal coolant for improved chip control Holds five SOET 13 indexable inserts Compatible with Palbit SOET 13 inserts Consistent metal removal from a compact design The compact 50 mm diameter design delivers a stable cutting platform with a 90° cutting angle, enabling square-face finishes with minimal tool overhang. Fitted for SOET 13 indexable inserts, this cutter head converts multiple small insert engagements into a smooth metal-removal process, reducing cycle time and the number of passes required for planar surfacing. The arrangement of five cutting edges distributes cutting forces evenly, which contributes to predictable tool behaviour and consistent surface quality — a practical advantage for serial production and finishing tasks. Integration that keeps production moving Built with internal coolant channels and a low overall profile, the unit simplifies chip evacuation and heat management, extending insert life and maintaining dimensional stability during longer runs. Replacement and clamping are straightforward thanks to the specified T15 Torx interface and M3.5×8.5 screws, enabling quick insert changes with standard tooling. The compact 45 mm overall length and light mass support easy handling and rapid positioning in small or modular toolholders, helping to reduce downtime and speed up machine set-up. Compatibility and operational fit for the shop floor This cutter head is supplied ready for SOET 13 indexable inserts and is declared compatible with Palbit-branded inserts, simplifying inventory for workshops that standardise on that manufacturer. The construction and specification suit a wide range of face-milling tasks where a short, coolant-fed head and multiple insert engagement are preferred. The robust engineering and standard fasteners make it a practical choice for engineering shops looking for repeatable results with commonly available inserts. Talk to Metav Werkzeuge about how the Teknik Makina face milling head T637TM with internal coolant can be integrated into existing setups; Metav’s team in Emmerich can advise on insert stocks, holder compatibility and delivery logistics via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: T637TM Label: 50 mm face milling head SOET 13 L45 mm with internal coolant Manufacturer: Teknik Makina eClass: 21181015 Dimensions & core data Diameter: 50 mm Overall length: 45 mm Weight: 0.398 kg Number of cutting edges: 5 Cutting angle: 90° Features & compatibility Internal coolant For SOET 13 indexable inserts Compatible with Palbit SOET 13 inserts Torx key: T15 Torx screw: M3.5×8.5 Product type: Face milling head (Planmesserkopf) FAQ Which insert size fits this cutter head? The face milling head accepts SOET 13 indexable inserts; compatibility with Palbit SOET 13 inserts is specified for the Teknik Makina T637TM. Does the head supply coolant to the insert cutting zone? Yes, the cutter head is equipped with internal coolant, designed to support coolant-fed cutting for improved chip control and tool life. What fastening hardware is required for insert changes? Insert clamping uses a T15 Torx key and M3.5×8.5 screws as specified for this Teknik Makina unit. Is the head suitable for installations with limited axial space? With an overall length of 45 mm and a compact 50 mm diameter, the T637TM is intended for compact setups and tight toolholder envelopes. How many cutting edges engage during a single revolution? The cutter head carries five cutting edges, which distribute cutting forces and support efficient surface machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

High-performance facing ensured by the 50 mm cutter body and directed internal coolant, delivering stable cuts and extended insert life; compatibility with WNMX 09T3 indexable inserts ensures versatile workshop use. Order the face milling head directly via Metav Werkzeuge or ask our consultants if needed. Face Milling Head for WNMX 09T3 – 50 mm, Internal Coolant (Teknik Makina) Face milling head engineered for precision facing and finishing on CNC machines, compatible with WNMX 09T3 indexable inserts for general workshop and production applications 50 mm diameter body Internal coolant supply Compatible with WNMX 09T3 inserts Compact 40 mm overall length Torx T8 screw M3x7 clamping Consistent material removal for predictable productivity The robust cutter body is designed to deliver stable cutting behaviour and repeatable surface quality, making it suitable for short-series production and jobbing work. With a 50 mm diameter and five cutting edges, the tool minimises vibration while maintaining a constant metal removal rate. This stability reduces scrap and rework, offering a clear efficiency advantage for shops that require reliable throughput without frequent tool adjustments. Improved tool life and cooling-directed chip control Built-in internal coolant directs cutting fluid straight to the insert-seat interface, which enhances heat management and facilitates chip evacuation. The result is extended insert life and reduced thermal wear on the cutter body. Compatibility with WNMX 09T3 indexable inserts from Korloy allows for a wide choice of grades and geometries, enabling adaptation to different materials and cutting strategies without changing the cutter head. Secure clamping and compact design for reduced downtime Secure insert retention is achieved via Torx T8 screws (size M3x7), providing reliable clamping torque and fast replacement cycles. The 40 mm overall length and modest mass (approx. 0.329 kg) reduce overhang and spindle load, improving run-out performance and extending spindle bearing life. These design choices simplify maintenance and shorten tool-change intervals, supporting a practical shop-floor workflow. Practical applications and user orientation Suited to facing, skim milling and finish passes on production and maintenance lathes or milling centres, the cutter head accepts standard WNMX 09T3 indexable inserts and is readily integrated into existing tool stations. The compact construction coupled with internal coolant makes the tool a pragmatic option for machinists and subcontractors seeking a balance of performance and serviceability in everyday operations. Technical documentation and insert recommendations are available to assist selection. Contact Metav Werkzeuge for tailored advice on Teknik Makina's 50 mm face milling head with internal coolant and confirm stock and delivery options from Emmerich Technical data SKU: T670-1TM Product type: Face milling head Brand: Teknik Makina Facts Diameter: 50 mm Shank diameter: 22 mm Overall length: 40 mm Weight: 0.329 kg Cutting edges: 5 ECLASS: 21181015 Special features Compatible with WNMX 09T3 indexable inserts Compatible insert manufacturer: Korloy Internal coolant: yes Torx screw: M3x7 Torx key size: T8 FAQ Which inserts are compatible with this cutter head? The face milling head accepts WNMX 09T3 indexable inserts; Korloy grades are specified for matching, and the cutter head (SKU T670-1TM) was designed around this insert family. Is there internal coolant and what is its benefit? Yes, internal coolant is integrated; the internal coolant on the Teknik Makina face milling head improves heat control and chip evacuation, contributing to longer insert life. What clamping hardware does the cutter head use? Clamping is provided by Torx T8 screws (M3x7), offering secure and repeatable insert fixation for consistent performance in production. What are the key dimensions and mass for setup considerations? Key figures: 50 mm diameter, 22 mm shank diameter, 40 mm overall length, weight approx. 0.329 kg (SKU T670-1TM). Is this tool suitable for CNC production environments? The compact design, internal coolant and compatibility with standard WNMX 09T3 inserts make this cutter head suitable for CNC facing and finishing tasks in production settings. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The compact design, 50 mm diameter and internal coolant make this face milling head a reliable choice for precise surfacing tasks; its six cutting edges and 90° cutting geometry ensure consistent shoulder quality and balanced wear. Order the cutter directly via Metav Werkzeuge or request advice from the consultants for smooth integration into existing tool sets. Face milling head T684TM – 50 mm diameter, internal coolant (Teknik Makina) The face milling head for XNKU 06T3 indexable inserts is a compact surfacing cutter head with internal coolant, designed for precise finishing and square-shoulder milling in confined setups. 50 mm cutting head diameter Internal coolant supply Six cutting edges for even wear Compatible with Palbit XNKU 06T3 inserts Process stability through compact, balanced design The compact cutter body combines a 50 mm diameter with a short overall length to reduce overhang and vibration, improving stability during finishing operations. The combination of six evenly distributed cutting edges and a 90° cutting angle supports consistent shoulder geometry and predictable tool life. Reduced tool movement leads to fewer reworks and steadier part tolerances, which is particularly valuable in small-batch production and precision workshops where machining consistency directly affects throughput and cost-efficiency. Integrated coolant for cleaner chips and longer service intervals Built-in internal coolant channels direct cutting fluid precisely to the cutting edge, improving chip evacuation and thermal control at the cutting zone. This targeted cooling reduces edge wear and helps preserve surface finish, so the cutter maintains performance over more cycles. The result is lower changeover frequency and a more reliable machining window, which supports leaner tool inventory management and fewer unscheduled stops on the shop floor. Fast insert changes and service-friendly fixation Compatibility with XNKU 06T3 indexable inserts and recognition of common insert suppliers such as Palbit simplify logistics and tool provisioning. Fast replacement is enabled by the M2.5x7 Torx screw and the matching T8 key, allowing quick, exact re‑clamping during maintenance. The use of standardised fixings minimises downtime and makes the cutter well suited to production environments that require predictable service intervals and straightforward spare-part handling. Designed for tight spaces and accurate surfacing The short overall length and modest mass of the cutter help in applications where access is restricted or where multiple setups would otherwise be required. The cutter is engineered for face and shoulder milling tasks where a true 90° shoulder is needed; its balanced design contributes to steadier feed rates and reduced chatter. Combined with the integrated coolant and multiple cutting edges, this head supports efficient, repeatable surfacing operations without compromising finish or cycle time. For procurement or technical queries regarding the Teknik Makina face milling head T684TM, contact Metav Werkzeuge for supply from Emmerich and tailored advice by e‑mail at info@metav-werkzeuge.com or by telephone at +49 2822 7131930 Technical data SKU: T684TM Manufacturer: Teknik Makina Core data Diameter: 50 mm Overall length: 40 mm Weight: 0.361 kg Cutting edges: 6 Cutting angle: 90° Special features Internal coolant For XNKU 06T3 indexable inserts Compatible with Palbit inserts Torx screw M2.5x7 Torx key T8 eClass: 21181015 FAQ Which indexable inserts fit this cutter? The face milling head accepts XNKU 06T3 indexable inserts; compatibility with Palbit‑type inserts is indicated for straightforward procurement and stocking. How does the internal coolant benefit machining performance? Internal coolant in the T684TM directs fluid to the cutting edge, improving chip evacuation and cooling to extend edge life and preserve surface finish during extended cycles. What is the significance of the 90° cutting angle? A 90° cutting angle produces square shoulders and clean part edges; the geometry is especially useful for finishing operations where perpendicular faces and tight tolerances are required. What fastenings are used for insert replacement? Insert clamping uses a Torx screw M2.5x7 secured with a T8 key, enabling rapid and repeatable insert changes with standardised tooling. Is the cutter suitable for confined or compact setups? Yes; the compact overall length and 50 mm diameter reduce overhang and improve stability, making the cutter suitable for tight workspaces and setups that demand low vibration. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact 50 mm body, effective internal coolant and four cutting edges for reliable face milling results; order directly via Metav Werkzeuge or request application advice from our consultants. Face milling head T628-1TM — 50 mm body, internal coolant (Teknik Makina) The Face milling head T628-1TM is a purpose-built cutter body for high-efficiency face milling with SNKX 1606 indexable inserts, ideal for machining centres where space and consistent surface quality matter. 50 mm body diameter for compact setups Internal coolant for improved chip evacuation Four cutting edges for higher material removal Compatible with SNKX 1606 Palbit inserts Efficient removal in confined setups The compact 50 mm body diameter combines rigidity with access in crowded tool zones, enabling higher effective material removal rates on face operations. With a maximum cutting diameter of 63 mm and a 45° cutting angle, the design supports shallower radial depths while maintaining stable cutting conditions. This results in shorter cycle times and repeatable surface finish, making the head a sound choice where throughput and consistency are paramount. Coolant-fed design that prolongs tool life The integrated internal coolant channel delivers cutting fluid directly to the cutting zone, improving chip evacuation and temperature control. Better cooling reduces thermal load on the insert pockets and cutting edges, which helps to extend insert life and maintain dimensional stability over longer series. For operations sensitive to heat-related wear, the coolant-fed arrangement supports more reliable process windows and fewer unplanned tool changes. Compatibility and quick serviceability for production floors Designed for SNKX 1606 indexable inserts and matched to Palbit geometries, the cutter head simplifies inventory by using a common insert family. The head accepts the specified M5x12 Torx screws and is set up with a T20 Torx key for straightforward reconditioning during service intervals. With four indexed cutting edges, insert rotations reduce tooling costs per produced component and support efficient shop-floor routines. Solid construction for repeatable accuracy A balanced cutter body weighing 0.458 kg and a total length of 48 mm provide the mechanical stability required for face milling across a range of production tasks. The combination of a compact form factor and a robust clamp arrangement ensures consistent runout control and predictable engagement with workpieces. When paired with appropriate machining parameters and SNKX 1606 inserts, the arrangement helps to secure reproducible dimensional outcomes and surface integrity. Contact Metav Werkzeuge for tailored application advice or to secure the Teknik Makina T628-1TM face milling head from stock in Emmerich; technical consultations and prompt shipping are available via Metav Werkzeuge. Technical data Article number: T628-1TM Product type: Face milling head Brand: Teknik Makina Label: 50 mm face milling head SNKX 1606 L48 mm with internal coolant Facts Body diameter: 50 mm Overall length: 48 mm Weight: 0.458 kg Max cutting diameter: 63 mm Cutting angle: 45° Cutting edges: 4 Special features Internal coolant For SNKX 1606 indexable inserts Compatible with Palbit inserts Torx key: T20 Torx screw: M5x12 ECLASS: 21181015 FAQ Which inserts fit this milling head? The T628-1TM accepts SNKX 1606 indexable inserts and is compatible with Palbit-manufactured insert geometries specified for that designation. Does the cutter head support coolant-through operation? Yes, the face milling head features internal coolant, directing fluid to the cutting zone to aid chip evacuation and thermal control. What torque tool is required for insert changes? Insert screws are M5x12 Torx fasteners and are designed for a T20 Torx key for removal and fitting. How many cutting edges are available per insert index? The cutter arrangement provides four indexed cutting edges, enabling sequential indexing to extend insert life and reduce cost per part. Is the head suitable for compact machining centres? The 50 mm body diameter and 48 mm overall length make the head well suited to tight toolspaces while providing the stiffness required for face milling. Manufacturer/Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine the compact 50 mm diameter, internal coolant and five cutting edges to achieve efficient facing with reduced downtime; order the face milling head directly via Metav Werkzeuge or consult our specialists for configuration advice. Face milling head for SNMX 1206 indexable inserts — 50 mm, internal coolant A face milling head engineered for precise facing and finishing with SNMX 1206 indexable inserts in compact machining setups. 50 mm diameter for compact operations Internal coolant to the cutting edge Compatible with SNMX 1206 inserts by Korloy Five cutting edges for high material removal Maximised facing performance with a compact design The compact 50 mm diameter body delivers high productivity where space is limited, while the five cutting edges permit substantial material removal per revolution. With an almost perpendicular 88° cutting angle, the tool produces flat faces with minimal scallop height and consistent surface integrity. The reduced mass of 0.348 kg lowers the dynamic load on the spindle, improving cycle stability and allowing faster acceleration and deceleration without compromising runout. These characteristics translate into shorter cycle times and predictable throughput for short-run and series production alike. Fast replacement and secure clamping for uninterrupted processing Designed for straightforward maintenance, the head accepts SNMX 1206 indexable inserts from Korloy and secures them with M4x12.5 Torx screws (Torx key T15), enabling rapid insert exchange and repeatable clamping. The standardised screw and key format simplifies stocking of consumables and tools in the workshop. Clear mechanical interfaces reduce setup errors, so abrasive wear or broken inserts can be replaced quickly and spindle dwell time is minimised, which improves overall equipment effectiveness in the machine shop. Targeted cooling that extends insert life and safeguards process stability Integrated internal coolant channels deliver cutting fluid directly to the cutting edge, reducing thermal load and evacuating chips more effectively than external flood cooling alone. By maintaining lower cutting temperatures, insert wear is slowed and edge life extended, which lowers tooling costs per component and reduces the frequency of tool interventions. This controlled cooling also stabilises metallurgical effects at the cut zone, supporting consistent tolerances across runs and helping to maintain dimensional quality without extensive secondary finishing. Suited to modern CNC shops and versatile facing tasks The design is optimised for CNC milling centres and compact turning/milling applications where access and precision matter. The head’s balanced geometry supports reliable indexing and contributes to a steady cutting process, while its compact footprint makes it suitable for multi-axis set-ups and close-quarters fixturing. Whether required for finishing passes or medium-duty roughing where flatness and surface finish are priorities, the tool offers a robust combination of performance and ease of use for professional metalworking environments. Contact Metav Werkzeuge today to discuss the Teknik Cutting Tools face milling head T343-1TM with internal coolant and confirm the right specification for your production needs; our Emmerich team will advise on compatibility and supply options. Technical Data SKU: T343-1TM Product type: Face milling head Manufacturer: Teknik Makina Label: 50mm Planmesserkopf SNMX 1206 L40mm mit Innenkühlung Facts Diameter: 50 mm Overall length: 40 mm Weight: 0.348 kg Cutting angle: 88° Cutting edges: 5 Special features Internal coolant For SNMX 1206 indexable inserts Compatible with Korloy inserts Torx key: T15 Torx screw: M4x12.5 Eclass: 21181015 FAQ What insert type fits this head? The head is configured for SNMX 1206 indexable inserts; Korloy SNMX 1206 inserts are compatible with the clamping interface provided. How does the internal coolant improve tool life? Direct coolant delivery to the cutting edge reduces temperature and improves chip evacuation, which increases insert life and supports consistent cutting performance with the face milling head T343-1TM. Which key and screw are required for insert clamping? Insert clamping uses M4x12.5 Torx screws and requires a Torx T15 key for secure and repeatable fastening. Is this head suitable for compact CNC machines? Yes. The compact 50 mm diameter and low mass make the head well suited to compact CNC cells and tight-access facing operations. Who supplies and supports this product? Teknik Cutting Tools manufactures the head; Metav Werkzeuge can advise on selection and supply for workshop needs. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of reliable mounting and stable cutting performance to maintain consistent face-milling results and reduce downtime; order the Planmesserkopf T722TM directly via Metav Werkzeuge or ask their consultants for application advice. Planmesserkopf T722TM — face-milling head with Ø50 mm diameter and 4 cutting edges by Teknik Makina The Planmesserkopf T722TM is a compact face-milling head for indexable inserts, engineered for metal-cutting operations where secure mounting and repeatable results matter Ø50 mm head diameter Four cutting edges for smooth material removal 22 mm mounting bore for firm clamping Torx T15 fixing screws M4x10 Consistent machining quality through stable geometry The milling head combines a precise outer diameter and a compact overall height to deliver a stable cutting platform. With a nominal Ø50 mm cutter body and 4 cutting edges, vibration is reduced and surface finish is improved; this leads to fewer rework cycles and more predictable cycle times. The result is higher first‑pass quality in routine machining, which supports efficient production planning and lower overall manufacturing costs. Fast, secure insert changes to keep processes moving A robust fixing system, specified with Torx T15 drive and M4x10 screws, ensures that inserts remain clamped under varying cutting forces. The head accepts indexable inserts, which are rapidly indexed or replaced without removing the holder; maintenance is simplified and cutter availability is maximised. These features translate into measurable reductions in tool-change time and improved uptime on the shop floor. Versatile mounting and proven compatibility The component fits a 22 mm mounting bore and is matched with established insert manufacturers such as YG-1, providing interchangeability within common tool systems. Its compact overall height supports constrained setups while the multi‑edge design enables balanced material removal. For operations seeking a dependable face-milling solution from a recognised supplier, this head represents a pragmatic choice that emphasises long-term usability and supply reliability. For tailored advice on the Teknik Makina face-milling head with Ø50 mm working diameter, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com to discuss compatibility and delivery options Technical data Article number: T722TM Manufacturer: Teknik Makina SKU: T722TM Dimensions & core data Diameter: 50 mm Overall height: 40 mm Number of cutting edges: 4 Mounting bore: 22 mm Mounting & special features Torx key: T15 Fixing screw: M4x10 Compatible insert manufacturer: YG-1 FAQ Which insert types fit this milling head? The milling head is designed for indexable inserts and is compatible with inserts from YG-1 as indicated in the product specification. What is the mounting diameter required? The tool requires a 22 mm mounting bore for installation. How many cutting edges does the head provide? The head is equipped with four cutting edges, allowing balanced cutting and improved surface finish. Which screw type secures the inserts? Inserts are secured using Torx T15 screws specified as M4x10 for reliable clamp force. Is the head suitable for compact setups? Yes, the compact overall height of 40 mm supports installation in constrained tool arrangements while maintaining performance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com