Gibt es einen Hahn und Kolb Online Shop?

Take advantage of the combination of robust clamping, long cutting reach and insert compatibility for reliable hole production; the stable 52 mm diameter and 156 mm cutting length ensure consistent performance in serial drilling. Order the U205TM directly via Metav Werkzeuge or ask our consultants if needed. Vollbohrer U205TM — indexable-insert drill body with 52 mm diameter and 156 mm cutting length by Teknik Makina The Vollbohrer U205TM is a drill body intended for heavy-duty machining where secure clamping and exchangeable cutting edges reduce downtime. 52 mm diameter for deep holes 156 mm cutting length for extended reach 40 mm shank diameter for stable clamping Compatible with WCM- 0804 inserts by Korloy Accurate holes with stable geometry and long cutting reach The U205TM combines a 52 mm nominal bore with a 156 mm cutting length, giving machining operations a clear advantage where repeatable hole geometry is required. The substantial 40 mm shank provides a rigid connection to the holder, which reduces runout and vibration; this results in better surface quality and longer insert life. For production environments, the measurable benefit is fewer reworks and predictable toolwear, because the drill body maintains alignment over longer cycles. Technical teams can therefore rely on consistent centre-to-centre accuracy when the holder and machine spindle meet the specified clamp and runout tolerances. Fast indexable-insert changes and reduced operating costs Designed to accept the WCM- 0804 insert family (supplier: Korloy), the tool body supports economical interchange of cutting edges without removing the entire tool from the spindle. The indexable system lowers hourly tooling costs: worn inserts are replaced quickly and the body can remain in the machine, limiting downtime. The 271 mm overall length and 68 mm shank engagement allow secure mounting in extended-reach setups while keeping the cutting geometry accessible. For process planners this means easier inventory control — only inserts need frequent replenishment — and improved uptime for batch drilling or repair work. Robust construction for demanding workshop and production use With a mass of 2.655 kg, this drill body is built for duty rather than light trimming tasks: the weight contributes to damping and steady cutting under load. The overall design supports stable cutting conditions and helps to avoid chatter in longer-hole drilling applications. The U205TM is suitable where repeatability and mechanical stability are priorities; because it accepts standard WCM- 0804 inserts from Korloy, it integrates into existing tooling strategies without complex adaptation. If further specification or machine-matching information is required, technical reference data and holder compatibility should be checked to ensure the best-fit clamping system. Contact Metav Werkzeuge today for application-specific advice on the Teknik Makina U205TM drill body, availability and matching insert recommendations — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: U205TM Manufacturer: Teknik Makina Product designation: Vollbohrer Facts Diameter: 52 mm Cutting length: 156 mm Shank diameter: 40 mm Shank engagement length: 68 mm Overall length: 271 mm Weight: 2.655 kg Special features Compatible inserts: WCM- 0804 Recommended insert supplier: Korloy Indexable-insert solution for economical edge changes FAQ Which inserts fit this drill body? The U205TM accepts WCM- 0804 inserts; Korloy is listed as the matching insert supplier for this drill body by Teknik Makina. What are the key dimensions to check for tool mounting? Check the 40 mm shank diameter and the 68 mm shank engagement length for holder compatibility with the U205TM drill body. What is the cutting reach of this tool? The tool provides a 156 mm cutting length with an overall tool length of 271 mm, offering extended reach for deeper hole machining. How heavy is the drill body and why does that matter? The U205TM weighs 2.655 kg; the mass contributes to damping and improved stability during cutting, which supports better surface finish and insert life. Can the drill body be used with existing Korloy insert stock? Yes, the U205TM is specified for WCM- 0804 inserts from Korloy, allowing integration with compatible insert inventories Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from precise chamfering with a Ø53 mm cutter that accepts TCMT 16T3 indexable inserts and offers both 45° and 90° chamfer options; the 25 mm shank provides secure clamping for repeatable results. Order the tool directly via Metav Werkzeuge or consult their specialists for application guidance. Chamfer Cutter S342TM – indexable cutter, Ø53 mm, 45°/90° chamfers (Teknik Makina) The Chamfer Cutter S342TM is an indexable milling cutter designed for efficient production of 45° and 90° chamfers in machining and workshop environments, suitable for use on milling heads and CNC toolholders. Indexable for TCMT 16T3 inserts 45° and 90° chamfer angles Ø53 mm diameter, 3 cutting edges 25 mm shank for secure clamping Deliver consistent chamfers and improved assembly fit The cutter delivers repeatable results thanks to its Ø53 mm body and a three‑edge cutting configuration that stabilises cutting forces. Chamfers at 45° and 90° are produced without additional setup changes, which simplifies jigging and reduces rework. The measurable cutting height 37 mm allows predictable material removal per pass, enabling planners to calculate cycle times and tolerances with confidence. This component is aimed at production workshops and contract manufacturers where process reliability is prioritised. Faster tool changes and reduced downtime with indexable inserts Designed for indexable operation, the tool accepts TCMT 16T3 inserts that are commonly stocked and quickly replaced. The use of indexable inserts minimises tool change time and keeps machining uptime high; insert indexing restores original geometry without regrinding. Fixing is executed with a Torx screw M3.5x8.5 and maintenance or replacement torque is applied via T15 drive tools. At a total length of 100 mm and a modest mass of 0.634 kg, the cutter offers good dynamic behaviour in automated spindles while remaining easy to handle during set‑up. Secure clamping and compatibility with common toolholders A 25 mm shank diameter ensures robust clamping in standard collets and hydraulic chucks, providing concentricity and resistance to deflection in interrupted cuts. The cutter’s design concentrates the cutting edges near the periphery for controlled chip evacuation and steady surface finish on chamfered edges. The product from Teknik Makina is suitable where quick indexability and predictable chamfer geometry are required in serial production or maintenance workshops, helping maintain process quality and assembly accuracy. Contact Metav Werkzeuge for tailored application advice on the Teknik Makina Chamfer Cutter S342TM and to arrange supply directly from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for technical clarification and order support Technical Data Article number: S342TM Manufacturer: Teknik Makina Name: Chamfer Cutter S342TM Facts Diameter: 53 mm Cutting edges: 3 Total length: 100 mm Shank diameter: 25 mm Cutting height: 37 mm Chamfer angles: 45°, 90° Weight: 0.634 kg Torx screw: M3.5x8.5 Torx key: T15 Special features For indexable inserts TCMT 16T3 Indexable design for fast insert changes Three cutting edges for stable cutting Suitable for milling heads and CNC toolholders FAQ What insert type does this cutter use? The cutter is designed for TCMT 16T3 indexable inserts, which provide fast replacement and consistent geometry for chamfering operations. Can this tool produce both 45° and 90° chamfers? Yes, the tool is configured to machine chamfers at 45° and 90° angles, offering flexibility for assembly preparations and edge finishing. What is the shank diameter and will it fit standard holders? The tool has a 25 mm shank, which is compatible with common collets and toolholders used in milling and CNC applications. How many cutting edges does the cutter have and what is the total length? The cutter features 3 cutting edges and a total length of 100 mm, balancing stability with reach in typical workshop setups. Which screw and drive size secure the inserts? Inserts are secured with a Torx screw M3.5x8.5, tightened or released using a T15 Torx key. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust design, long cutting reach and easy insert interchangeability for reliable performance in series drilling. The large 53 mm diameter and 159 mm cutting length deliver consistent hole quality while the 40 mm shank ensures secure clamping. Order the solid drill directly via Metav Werkzeuge or ask our consultants for application guidance. Solid Drill U207TM by Teknik Cutting Tools — 53 mm diameter, 274 mm overall length Solid Drill U207TM is a heavy-duty indexable drilling tool designed for stable, repeatable holemaking in workshop and light industrial production environments 53 mm cutting diameter 159 mm cutting length 40 mm shank diameter Compatible with Korloy WCM‑0804 inserts Consistent hole quality for production environments The U207TM is engineered to combine a long cutting reach with dimensional stability. The 53 mm nominal diameter and 159 mm cutting length allow deep-hole capability without compromising concentricity, translating into fewer reworks and higher throughput. The tool’s geometry is selected to reduce vibration and maintain repeatable accuracy across runs, which benefits batch and series production where consistent hole size is critical. For technicians less familiar with tooling jargon: longer cutting length means fewer tool changes when producing deeper holes. Insert system that reduces downtime and tooling cost Designed for use with WCM‑0804 indexable inserts from Korloy, the tool provides controlled chip formation and fast insert replacement. Using an insert system lowers per‑hole tooling cost compared with single‑piece cutters and allows quick top‑ups during shift changes. The compatibility with a widely available insert type means the spare parts flow is straightforward, supporting uninterrupted production. Clear seating and positive clamping of the insert pocket contribute to predictable cutting performance and straightforward maintenance. Secure clamping and balanced dimensions for drill stability The substantial 40 mm shank and 274 mm overall length deliver both clamp security and the reach required for many component designs. The shaft dimensions are chosen to work with standard toolholders while offering sufficient mass to damp cutting forces; the tool’s 2.74 kg mass reflects that balance. Operators will notice fewer chatter marks and improved surface finish where tool rigidity is essential. For workshop planners, this means fewer rejects and a more efficient machining sequence without needing dedicated fixturing changes. Contact Metav Werkzeuge in Emmerich for tailored application advice and stock availability of the Teknik Cutting Tools Solid Drill U207TM. Technical data Article number: U207TM Designation: Vollbohrer (solid drill) Manufacturer: Teknik Makina Diameter: 53 mm Overall length: 274 mm Cutting length: 159 mm Shank diameter: 40 mm Shank length: 68 mm Weight: 2.74 kg Compatible insert type: WCM- 0804 Compatible insert manufacturer: Korloy Facts Diameter: 53 mm Overall length: 274 mm Cutting length: 159 mm Shank diameter: 40 mm Shank length: 68 mm Weight: 2.74 kg Special features Indexable insert system Insert designation WCM‑0804 Compatible with Korloy inserts Robust shank for secure clamping FAQ What materials is this drill suitable for? The Solid Drill U207TM is intended for general-purpose drilling in common engineering materials; compatibility with specific alloys depends on insert grade and cutting data rather than the tool body itself. Which inserts are used with this tool? This drill accepts WCM‑0804 indexable inserts; Korloy grades are a standard match for typical steel and cast applications. How does the shank diameter affect performance? A 40 mm shank provides improved clamping stability and vibration damping, which helps the tool maintain hole accuracy during deeper cuts. Can the cutting length be changed or extended? The tool’s 159 mm cutting length is fixed by design; changing reach requires a different tool type or a toolholder solution with extended reach while observing rigidity limits. Is the U207TM suitable for series production? Yes. The combination of a 53 mm diameter, long cutting length and an indexable insert system makes the U207TM well suited to repetitive production where fast insert changes and consistent hole quality are priorities. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a 45 mm shank for secure clamping, a 400 mm overall length for extended reach and compatibility with KNUX 1604 inserts for efficient indexable tooling — order the RK758TM directly via Metav Werkzeuge or consult our advisors for specification support RK758TM Boring bar – CKUNR for KNUX indexable inserts, 45 mm shank by Teknik Cutting Tools A RK758TM boring bar designed for right-hand turning and extended-reach internal and external machining with KNUX 1604 indexable inserts. Robust 45 mm shank for stable clamping Compatible with KNUX 1604 indexable inserts 400 mm overall length for extended reach Stable clamping for reliable heavy machining The RK758TM is built around a 45 mm shank, which provides the rigidity required for repeatable results in demanding setups. A larger shank diameter reduces vibration and run-out, translating into improved surface finish and longer insert life. The 54 mm diameter at the cutting end and the 93° cutting angle support effective chip formation during right-hand cutting, making this bar suitable where stability and predictable cutting behaviour are priorities. The substantial mass of 4.924 kg further dampens chatter in many turning operations, reducing secondary finishing steps. Extended reach with predictable geometry With an overall length of 400 mm, the RK758TM offers reach for deeper bores and larger workpieces while maintaining stability through its robust design. The 60 mm cutting height gives sufficient support for indexable inserts to engage material cleanly and consistently. Clear, measurable geometry makes process planning straightforward: feeds and speeds can be set knowing the toolholder geometry and mass will behave consistently, which supports higher first-pass yield and reduced cycle time in production environments. Insert system and handling designed for productivity The ISO designation S45V CKUNR indicates a CKUNR-style holder compatible with KNUX 1604 indexable inserts, a common and readily available insert format in industry. Compatibility with standard inserts simplifies tool inventory and changeover. The right-hand cutting configuration allows integration into established lathe programmes without modification. Tool changes are simplified by the indexable system, reducing downtime compared with brazed or one-piece tooling and supporting a leaner workshop workflow. Proven choice for workshops and production lines Specifying tooling from an experienced supplier reduces procurement risk: this holder’s defined dimensions and standard insert compatibility support predictable purchasing and stocking. The combination of robust shank diameter, defined cutting geometry and standardised insert format makes the holder an economical choice for mixed-batch production or workshop environments that require versatility and repeatability. Metav’s position as a precision partner ensures reliable supply and technical guidance from its Emmerich facility. For machining tasks that require extended reach and secure clamping, contact Metav Werkzeuge to source the Teknik Cutting Tools RK758TM boring bar or discuss process integration via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: RK758TM Description: CKUNR for KNUX Indexable Inserts ISO designation: S45V CKUNR Manufacturer: Teknik Makina Facts Shank diameter: 45 mm Cutting height: 60 mm Diameter: 54 mm Overall length: 400 mm Weight: 4.924 kg Cutting angle: 93° Cutting direction: Right-hand eClass: 21180806 Special features Suitable for KNUX 1604 indexable inserts CKUNR-style holder Designed for indexable-insert changeover Robust construction for reduced vibration FAQ What insert type fits this holder? The RK758TM accepts KNUX 1604 indexable inserts in a CKUNR holder configuration, enabling use of widely available insert grades Is this tool suitable for right-hand cutting only? Yes, the holder is configured for right-hand cutting and is optimised for typical turning and boring operations in that direction What are the key dimensions to consider for setup? Relevant dimensions include a 45 mm shank, 54 mm diameter, 60 mm cutting height and 400 mm overall length for fixture planning How does the shank diameter affect performance? A 45 mm shank increases rigidity and reduces vibration, which improves surface finish and extends insert life under comparable cutting conditions Can this holder be used in small workshop lathes? The RK758TM’s mass and reach are intended for stable setups; assessment of machine capacity and tooling clearance is recommended before selection Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of high cutting capacity, precise insert compatibility and secure shank mounting for uninterrupted production. Order the drill body directly via Metav Werkzeuge or consult our technical team for application-specific advice. Vollbohrer U209TM — indexable insert drill body with 54 mm diameter, Korloy WCM-0804 compatibility A robust indexable insert drill body, Vollbohrer U209TM, engineered for medium-deep holemaking in CNC machining and suitable for Korloy WCM-0804 inserts Indexable insert compatible WCM-0804 Large 54 mm diameter for deep holes 162 mm effective cutting length Robust 40 mm shank, secure mounting Increase throughput with consistent, repeatable holemaking This drill body is built for high productivity: the 54 mm nominal diameter combined with a 162 mm cutting length provides a balance between material removal and tool rigidity, enabling longer uninterrupted cycles on batch work. The design reduces the need for frequent tool changes and supports consistent hole quality, which in turn improves process stability and lowers per-part machining time. Using an indexable concept means cutting edges can be rotated or replaced rapidly, keeping spindle downtime to a minimum and maintaining a steady production flow. Fast insert replacement and reliable clamping for predictable results The modular concept accepts WCM-0804 inserts from Korloy, allowing straightforward replacement and familiar grades for different materials. A substantial 40 mm shank provides a secure connection to standard toolholders, improving runout behaviour and vibration damping during drilling. These factors reduce cycle variation and extend the service life of both inserts and the body, translating into measurable cost-efficiency for repetitive tasks. Clear mechanical interfaces simplify maintenance and spare-part planning for workshop managers. Practical dimensions and handling for workshop integration With an overall length of 277 mm and a body weight of 3.21 kg, the tool balances reach with manageable mass for handling and fixturing. The 162 mm cutting length supports medium-deep hole operations without resorting to specialist deep-hole equipment, while the 40 mm mounting diameter fits typical collets and holders used in production environments. The combination of familiar dimensions and indexable inserts makes this body straightforward to integrate into existing tool sets, reducing setup time and the complexity of inventory management. Trusted supply and application support for uninterrupted operations Supplied under the Teknik Cutting Tools line and stocked by Metav, the assembly benefits from a reliable European distribution channel. Metav’s service model focuses on predictable delivery, broad spare-part availability and application advice to match insert grades and feed/speed recommendations with the intended workpiece material. This support helps bridge the knowledge gap where insert grades and machining parameters determine final surface finish and hole tolerance. Discuss application specifics with Metav Werkzeuge for the Teknik Cutting Tools U209TM indexable insert drill body and arrange compatibility checks or reserve stock via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: U209TM Manufacturer: Teknik Cutting Tools Product: Indexable insert drill body (translated from Vollbohrer) Dimensions & core data Diameter: 54 mm Overall length: 277 mm Cutting length: 162 mm Shank diameter: 40 mm Shank length: 68 mm Weight: 3.21 kg Suitable inserts & compatibility Compatible inserts: WCM-0804 Recommended insert manufacturer: Korloy Manufacturer SKU reference: U209TM FAQ What inserts fit this drill body? The drill body is compatible with WCM-0804 indexable inserts; Korloy grades are commonly used with this holder for a wide range of applications. What are the main dimensions to consider for tool change and holder selection? Key values are 54 mm diameter, 162 mm cutting length, 277 mm overall length and a 40 mm shank; these determine holder choice and reach. Is the shank diameter suitable for standard toolholders? Yes, the 40 mm shank is intended for standard holders that accept that mounting diameter, providing stable clamping for precision drilling. How does insert replacement affect production downtime? Because the body uses indexable WCM-0804 inserts, edge changes are quick and repeatable, cutting downtime and maintaining consistent cycle times with minimal spindle idle time. Which brand manufactures this drill body and what is the SKU? The body is produced under Teknik Cutting Tools and listed as SKU U209TM for reference in ordering systems. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the precise compatibility with the 55–75 CCMT 09T3 boring tool and the assured fit of an original Teknik Makina cartridge to reduce set-up variance and secure repeatable results on the shop floor. Order the cartridge directly via Metav Werkzeuge or ask our consultants for tailored advice. Cartridge KR108TM — Cartridge for Boring Tool 55–75 CCMT 09T3 by Teknik Makina, precision fit The Cartridge KR108TM is a dedicated replacement cartridge for the Boring Tool 55–75 CCMT 09T3, designed to ensure a secure interface between insert and holder for industrial boring applications Precision fit for CCMT 09T3 inserts Compatible with 55–75 mm boring tools Original Teknik Makina part Secure mounting for repeatable runs Reduced set-up time through precise compatibility The KR108TM cartridge is engineered to provide a precision fit with CCMT 09T3-style inserts, which directly reduces alignment effort during tool changes. A correctly matched cartridge shortens the machining downtime caused by re‑setting inserts and improves first‑pass accuracy. In practice, a stable cartridge interface translates into fewer adjustments at the machine and a more predictable production rhythm, helping maintain cycle times and component tolerances. Reliable seating and repeatable performance As the interface component between insert and boring body, the cartridge’s role is to deliver secure clamping and consistent seating geometry. This stability enhances repeatability across batches and simplifies quality control: once the cartridge is installed and the insert seated, concentricity and cutting geometry remain stable, which lowers scrap rates and reduces the need for corrective machining. The cartridge also supports consistent chip evacuation and tool life when used with appropriately specified inserts. Integration advice and workshop application The cartridge is specified for use with the 55–75 mm boring range and CCMT 09T3 inserts; compatibility should be verified against the toolholder series and insert specification in the boring assembly. For workshop managers and fitters seeking modularity, this cartridge enables straightforward replacement without modifying the existing holder. If questions remain about matching the cartridge to a particular boring bar or insert grade, Metav Werkzeuge can provide technical clarification to ensure correct integration and efficient deployment. Contact Metav Werkzeuge for expert guidance on integrating Teknik Makina cartridges and to arrange prompt delivery from Emmerich to the workshop bench Technical data Article number: KR108TM Name: Cartridge for Boring Tool 55–75 CCMT 09T3 Manufacturer: Teknik Makina Core data Compatible range: 55–75 mm Insert type: CCMT 09T3 SKU: KR108TM Special features Intended for: Boring tool 55–75 CCMT 09T3 Type: Cartridge Internal ID: KR108TM FAQ Is this cartridge compatible with all 55–75 mm boring bars? Compatibility depends on the boring bar’s clamp and internal seat geometry; the Cartridge KR108TM is specified for boring tools with a 55–75 mm range and CCMT 09T3 inserts and should be checked against the bar’s holder design before fitting. Can the KR108TM be used with different insert grades? Yes, the KR108TM accepts CCMT 09T3 inserts irrespective of carbide grade, but insert coating and grade should be chosen according to the material being machined and the recommended insert data from the insert manufacturer. How does the cartridge affect machining repeatability? By providing a consistent seating surface and secure clamp interface, the cartridge improves concentricity and reduces variation between tool changes, leading to better repeatability across production runs. Are spare cartridges and replacement parts available for this SKU? Spare units corresponding to SKU KR108TM are available as original Teknik Makina parts; consult the product listing or Metav Werkzeuge for stock information and ordering details. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Compact design for stable seating and fast changeover—combine precision seating, robust fit and quick replacement to keep production flowing. Order the cartridge directly via Metav Werkzeuge or consult the team for application advice. Cartridge for Boring Tool 55–75 CCMT 1204 — precise seating & quick changeover (Teknik Makina) A cartridge for the 55–75 CCMT 1204 boring tool that secures insert seating and simplifies tool replacement for turning and internal boring operations Secure insert retention Compatible with 55–75 CCMT 1204 Fast replacement for minimal downtime Durable construction for industrial use Improved process stability through precise seating A correctly matched cartridge delivers a measurable advantage in machining consistency. By providing precision seating for the cutting insert, the component reduces micro-movement during cutting, which in turn lowers vibration and improves surface finish. This results in longer tool life and fewer rejects per shift. The focus here is on repeatable, verifiable performance rather than vague claims: a stable holder contributes directly to predictable cycle times and consistent part tolerances. Rapid changeovers to keep machining cells productive Minimising non-productive time is central to modern shopfloor efficiency. The cartridge is designed for quick changeover, permitting fast insert or holder swaps and so reducing fixture downtime between batches. In practice this means set-up windows are shortened and throughput is increased without compromising accuracy. For production planners, this is a concrete operational benefit: less idle spindle time and improved utilisation of turning and boring assets. Clear compatibility and supply reliability for production planning Compatibility with the specified boring tool family is documented, easing procurement and inventory decisions. The cartridge supports the 55–75 CCMT 1204 specification, simplifying parts management for toolrooms and maintenance departments. Sourcing is backed by Metav’s central European distribution, which acts as a quality filter and supply hub; this ensures reliable availability and traceable origin for the replacement component. The overall effect is lower administrative overhead and more dependable production planning. Contact Metav Werkzeuge for tailored availability and application guidance on the Teknik Makina cartridge (SKU KR115TM) for the 55–75 CCMT 1204 — email info@metav-werkzeuge.com or call +49 2822 7131930 for fast consultation and order processing Technical Data Article number: KR115TM Description: Cartridge for Boring Tool 55–75 CCMT 1204 Manufacturer: Teknik Makina Data No core numerical specifications available Special features Compatible with 55–75 CCMT 1204 boring tool Intended for secure insert retention Facilitates quick replacement and minimal set-up time Manufacturer SKU: KR115TM UID: KR115TM FAQ What machines is this cartridge compatible with? The cartridge is specified for use with the 55–75 CCMT 1204 boring tool family; compatibility is stated in the product record for ease of tool selection. How does the cartridge affect machining quality? By providing precision seating and a secure fit, the cartridge reduces micro-movement and vibration, which improves surface finish and tool life when used with the appropriate boring tool. Is replacement straightforward for maintenance teams? Yes, the design supports fast changeover and straightforward swapping of the cartridge and insert, helping to reduce setup time on the shopfloor. Can this component be sourced via Metav Werkzeuge? Metav Werkzeuge lists and supplies the Teknik Makina cartridge (SKU KR115TM) and can advise on stock and compatibility for production needs. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Robust drilling performance with a Ø55 mm cutting diameter and a secure 40 mm shank delivers reliable hole quality and process stability; the indexable concept using WCM-0804 inserts keeps downtime low. Order the U211TM directly via Metav Werkzeuge or ask our consultants for application advice. U211TM — Indexable insert drill, Ø55 mm, for WCM-0804 inserts (Teknik Makina) The U211TM is an indexable drill body designed for stable, high-precision holemaking in CNC machining where replaceable Korloy WCM-0804 inserts are preferred. Ø55 mm nominal diameter Compatible with Korloy WCM-0804 inserts 165 mm effective cutting length 40 mm robust shank diameter Reliable hole quality and process stability The design focuses on repeatable results in series production: a Ø55 mm nominal diameter combined with a 165 mm cutting length provides consistent engagement, while the mass and geometry of the tool body reduce vibration during cutting. This stability translates into fewer scrap parts and steadier cycle times, making the tool suitable where hole tolerance and surface finish matter. The indexable concept means only the cutting edges need attention, not the whole tool, which preserves machine uptime and supports tighter process control. Economical machining with indexable inserts Using WCM-0804 indexable inserts from Korloy enables quick edge changes and predictable machining costs. The insert-based approach separates cutting-edge wear from the tool body, so maintenance is limited to exchanging inserts and checking clamp integrity. Where cutting conditions vary, the system allows rapid adaptation by selecting insert grades or geometries without replacing the drill body, supporting cost-efficiency and operational flexibility in production environments. Rigidity, clamping and dimensional data for stable setup A 40 mm shank diameter and 68 mm shank length ensure secure clamping in standard toolholders, while the 280 mm overall length gives sufficient reach for many workpiece geometries. The tool’s 3.237 kg mass contributes to dampening of minor tool deflection under load, improving concentricity and hole roundness. These dimensional characteristics support robust setups on machining centres and reduce the risk of chatter when combined with appropriate holder and spindle rigidity. Practical setup pointers and lifecycle considerations For best results, match the holder and spindle clamping to the 40 mm shank and verify runout before production runs. Insert seating and torque of the clamping screws should be checked at regular intervals to maintain consistent cutting conditions. The modular nature of the design simplifies refurbishment: worn inserts are replaced quickly and the body inspected for damage, which helps extend overall tool service life and keeps the cutting process predictable. For application advice or to secure the U211TM for a specific CNC process, contact Metav Werkzeuge in Emmerich for tailored recommendations and prompt delivery coordination. Technical data Article number: U211TM Manufacturer: Teknik Makina Product type: Insert drill (indexable) ECLASS: 21180201 Facts Diameter: 55 mm Overall length: 280 mm Cutting length: 165 mm Shank diameter: 40 mm Shank length: 68 mm Weight: 3.237 kg Special features For WCM-0804 indexable inserts Compatible with Korloy insert geometry Indexable drill body for CNC drilling FAQ What insert type does this drill use? The drill accepts Korloy WCM-0804 indexable inserts; the U211TM is configured for that insert geometry. What are the key dimensions to check for holder compatibility? Verify the 40 mm shank diameter and 68 mm shank length to ensure correct clamping in the selected toolholder for the U211TM. Is the U211TM suitable for long-reach drilling? With an overall length of 280 mm, the tool provides moderate reach; stability depends on holder and spindle rigidity as well as clamping practice. How does the indexable design affect maintenance? The indexable design reduces downtime by allowing quick replacement of worn WCM-0804 inserts rather than replacing the entire tool body, simplifying maintenance cycles for the U211TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise T-slot milling with a 55 mm diameter cutting head and compatibility with RD-- 1003 indexable inserts for consistent slot geometry and reduced tool change time — order directly via Metav Werkzeuge or consult the team for tailored tooling advice. T-slot cutter for RD-- 1003 indexable inserts, 55 mm diameter The T-slot cutter is designed for efficient creation and finishing of T-slots in machining setups, offering stable toolholding and repeatable results in industrial milling applications. 55 mm diameter for robust slotting Compatible with RD-- 1003 inserts 16 mm shank for secure clamping Six cutting edges for balanced cutting Consistent slot geometry and production reliability Precision in slotting begins with tool geometry and insert compatibility. The 55 mm diameter cutting head combined with RD-- 1003 indexable inserts provides repeatable pocket and T-slot profiles, reducing the need for rework. The cutter’s design translates insert indexing into predictable cutting forces, which helps maintain dimensional tolerances across batch production. By using indexable inserts, the emphasis is on fast, cost-effective maintenance: when an edge is worn, only the insert needs replacement rather than the whole tool, supporting uninterrupted workflow and predictable uptime. Stable mounting and improved surface finish A secure connection between spindle and cutter is essential for vibration control and surface quality. The 16 mm shank and overall compact form (total length 45 mm) deliver a rigid interface that minimises chatter during milling, while the six cutting edges distribute load evenly for smoother engagement. The cutting length 24 mm is optimised to reach common T-slot depths without compromising stiffness. These features combine to lower acoustic emissions, reduce tool wear and deliver a finer finish on the machined slot, which is particularly important when subsequent assembly or sliding fits are required. Practical handling and insert fastening explained Maintenance and insert replacement are straightforward: inserts are secured with an M3.5x8.5 screw tightened using a T15 torx key, providing a reliable clamping method that resists loosening under load. The low mass (approx. 0.135 kg) of the cutter helps reduce inertial effects during direction changes, making it well suited to both CNC milling centres and manual machines with robust toolholders. For identification and reordering, the cutter is listed under SKU TKC180TM, matching tooling inventory with production requirements and spare-part logistics. Suitable operations and tool lifecycle management This cutter is intended for standard T-slot milling tasks in industrial settings where indexable tooling enhances efficiency. The modular nature of indexable inserts supports predictable lifecycle planning: track insert usage, replace individual edges as they reach wear limits, and maintain a small inventory of spare inserts rather than oversized complete cutters. Attention to correct clamping torque on the M3.5x8.5 screw and regular inspection of the insert seats will extend service life and contribute to consistent part quality throughout production runs. For technical selection and procurement of the Teknik Makina T-slot cutter (SKU TKC180TM) with RD-- 1003 compatibility, contact Metav Werkzeuge for expert advice and order handling to ensure the right tooling configuration for the application. Technical data SKU: TKC180TM Label: 55mm T-Nut Fräser RD-- 1003 L45mm Manufacturer: Teknik Makina Dimensions & weight Diameter: 55 mm Total length: 45 mm Cutting length: 24 mm Shank diameter: 16 mm Number of cutting edges: 6 Weight: 0.135 kg Compatibility & assembly Compatible inserts: RD-- 1003 (indexable inserts) Torx key: T15 Fastening screw: M3.5x8.5 Product type: T-slot cutter ECLASS: 21180605 FAQ Which inserts fit this cutter? The cutter accepts RD-- 1003 indexable inserts, which are specified for the tool’s pocket and clamping geometry. What shank size is required for mounting? A 16 mm shank holder or collet is required to mount the cutter securely for machining operations. How are the inserts secured in place? Inserts are fastened with an M3.5x8.5 screw and can be tightened or loosened using a T15 torx key. What is the designation for reordering this cutter? Reorder using SKU TKC180TM, which identifies the 55 mm T-slot cutter compatible with RD-- 1003 inserts. Is the cutter balanced for high-speed milling? The cutter’s multiple cutting edges and compact geometry promote balanced cutting behaviour; check machine and spindle specifications for permitted speeds. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, precision‑oriented design that pairs a 55 mm cutting diameter with compatibility for RD-- 12 indexable inserts, delivering reliable T‑slot machining and predictable tool life; order directly via Metav Werkzeuge or consult the Metav team for application advice. T-slot cutter TKC185TM — 55 mm diameter, for RD-- 12 indexable inserts (Teknik Makina) T-slot cutter TKC185TM for machining T‑slots using RD-- 12 indexable inserts; engineered for stable performance in workshop and industrial milling. 55 mm cutting diameter Compatible with RD-- 12 inserts Five cutting edges for stable cuts Shaft Ø 16 mm, L45 mm overall Faster, consistent T‑slot production through optimised insert use The combination of a 55 mm cutting diameter and compatibility with RD-- 12 indexable inserts enables efficient slot creation with consistent geometry. Indexable inserts allow multiple cutting edges to be used sequentially, so cycle times are maintained while shop floor handling is reduced. This design supports a measurable increase in productivity and reduces the frequency of full‑tool changes, which is particularly beneficial in repetitive production or batch machining of profiles. Stable clamping and compact dimensions for secure machining A robust shaft Ø 16 mm and an overall length of 45 mm provide a compact tool with good rigidity, helping to minimise chatter and deflection in clamped setups. The 24 mm cutting length on the shaft gives sufficient engagement for typical T‑slot depths while keeping the overhang short. Together these dimensions reduce vibration and improve surface finish, making the cutter suitable for both conventional milling machines and CNC toolholders that require precise, repeatable results. Practical fastening and simple insert replacement for predictable maintenance Inserts are secured with a Torx screw M3.5x8.5, tightened using a T15 Torx key, allowing quick, tool‑guided index changes without complex adjustments. The cutter features five cutting edges, which spreads wear and extends the interval between insert rotations. For teams new to indexable tooling, this means predictable maintenance cycles and easy stock management of RD-- 12 inserts, simplifying toolroom logistics while maintaining cut quality. For tailored application advice or to arrange supply through Metav Werkzeuge, contact the Metav technical team at info@metav-werkzeuge.com or call +49 2822 7131930 — assistance is available from our Emmerich facility. Technical data Article number: TKC185TM Manufacturer: Teknik Makina Product type: T‑slot cutter Facts Cutting diameter: 55 mm Overall length: 45 mm Shaft diameter: 16 mm Shaft cutting length: 24 mm Number of cutting edges: 5 Weight: 0.138 kg Special features Compatible with RD-- 12 indexable inserts Torx key: T15 Torx screw: M3.5x8.5 Label: 55mm T‑Nut Fräser RD-- 12 L45mm FAQ What insert type does this cutter use? The cutter is designed for RD-- 12 indexable inserts, which are secured with a Torx screw M3.5x8.5. Is the shaft compatible with standard toolholders? The Ø 16 mm shaft and compact L45 mm overall length suit common milling holders that accept 16 mm shanks. How many cutting edges are available before an insert change? Each insert configuration offers multiple edges; the cutter itself is specified with five cutting edges to distribute wear and extend service intervals. Can this tool be used for deep T‑slots? The tool provides a 24 mm cutting length on the shaft; suitability for deeper slots depends on required slot depth and clamping arrangement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact combination of rigidity and insert flexibility: the T-slot cutter offers a 55 mm diameter and a 25 mm shank for stable, repeatable slotting; compatible with Korloy MGM 5C inserts for efficient chip formation. Order the tool directly via Metav Werkzeuge or consult the advisors for application-specific guidance. T-slot cutter TKC306TM — 55 mm diameter, 25 mm shank (Teknik Makina) A T-slot cutter designed for precision T-slot and round milling in CNC and conventional milling machines, offering sturdy shank support and insert interchangeability for industrial production environments 55 mm diameter for T-slot shaping 25 mm shank for rigid toolholding Compatible with Korloy MGM 5C inserts Robust two-edge configuration Stable machining through rigid geometry and shank design The cutter combines a 25 mm shank with a balanced body and a 120 mm overall length to reduce run-out and vibration during T-slot formation. This geometry enhances surface finish and extends tool life by maintaining a consistent cutting line, which is particularly important when slot tolerances are tight. The tool’s mass distribution and 0.513 kg weight support steady spindle loads, enabling reliable cycle times and fewer reworks in series production. Insert system and fast serviceability for minimal downtime Designed for use with Korloy MGM 5C indexable inserts, the cutter simplifies reconditioning: worn inserts are replaced without regrinding the tool body. The secure fixing with an M8 Torx screw and supplied 6 Allen key specification ensures repeatable clamping torque and quick changeover. With 2 cutting edges and a 5 mm cutting height, material removal can be efficient while preserving insert life; this configuration supports predictable chip flow and reduces the need for complex coolant strategies. Application versatility and process reliability in industrial settings As a round milling solution, the tool handles both standard T-slots and related profile milling tasks, delivering consistent dimensional control across batches. The measured distance from cutting edge to shank (15.25 mm) gives a clear datum for setup, aiding fixture design and repeatability on jigs or CNC vises. The combination of indexable inserts and a sturdy shank reduces tooling inventory complexity while keeping machining costs manageable for workshops and production lines focused on throughput and precision. For application advice or to discuss suitable insert grades and cutting parameters, contact Metav Werkzeuge for personalised recommendations and procurement support. Technical data Article number: TKC306TM Manufacturer: Teknik Makina Diameter: 55 mm Shank diameter: 25 mm Overall length: 120 mm Cutting edges: 2 Cutting height: 5 mm Compatible inserts: MGM 5C (Korloy) Fixing screw: M8 Torx Torx key: 6 Allen Weight: 0.513 kg Core specifications Diameter 55 mm Shank 25 mm Overall length 120 mm Cutting height 5 mm Distance cutting edge–shank 15.25 mm Cutting edges 2 Weight 0.513 kg Special features Compatible with Korloy MGM 5C inserts Round milling cutter application Secure M8 fixing screw Indexable insert system for fast service FAQ What inserts fit this cutter? The cutter accepts Korloy MGM 5C indexable inserts; the design and pocket geometry are optimised for this insert type to ensure stable cutting and predictable chip control. Is the tool suitable for heavy-duty slotting? The tool’s 25 mm shank and two-edge configuration allow stable slotting under standard industrial feeds; for very deep or interrupted cuts, adjust parameters and check insert grade recommendations. How is the insert secured and serviced? Inserts are secured with an M8 Torx screw; replacement is straightforward and reproducible, enabling quick changeovers and minimal downtime for the TKC306TM. Can the cutter be used for round milling tasks? Yes, the geometry supports round milling and T-slot machining, making the cutter a versatile choice for profile milling and slot operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid, indexable solution that combines stable clamping with insert flexibility: the TKB120TM suits internal boring tasks where quick insert replacement and controlled cutting length improve uptime. Order via Metav Werkzeuge or consult their specialists for workshop-ready delivery from Emmerich. Teknik Makina TKB120TM Boring Bar — CCMT 09T3 Compatible, Ø45–56 mm An TKB120TM boring bar engineered for internal boring and turning operations on medium-sized lathes, compatible with CCMT 09T3 indexable inserts. Indexable insert: CCMT 09T3 compatible Max cutting diameter 56 mm 32 mm shank for rigid clamping Overall length 180 mm, cutting length 120 mm Stable support for precision internal machining The TKB120TM combines a 32 mm shank with a balanced body to deliver rigid clamping and consistent cutting conditions. That structural stability reduces chatter and helps achieve repeatable diameters on internal bores. For shops aiming to improve process reliability, the combination of a solid shank and a dedicated cutting length means fewer rejects and less rework, while the measured mass contributes to a controlled cutting feel during heavy cuts. Fast insert changes and economical running costs Designed around indexable inserts, specifically CCMT 09T3, the tool enables quick edge changes without regrinding. This approach lowers tooling overhead and minimises downtime compared with solid-tool reconditioning. The replaceable-insert concept allows the workshop to restore cutting edges in seconds, maintaining cycle times and preserving machine utilisation — a clear rational gain for production environments focused on throughput. Defined reach and machining envelope for consistent results With a 120 mm cutting length and 180 mm overall length, the bar provides a predictable machining envelope that suits many internal turning set-ups. The specified 56 mm max cutting diameter and nominal Ø45 value allow planners to select the tool where bore access and depth are limiting factors. Clear dimensional data supports fixture planning and reduces the need for trial-and-error on the shop floor. Practical handling and compatibility on the machine The tool accepts the common CCMT insert form, making it straightforward to integrate into existing tooling inventories. The moderate weight of the assembly contributes to stability without imposing excessive spindle load, and the standardised shank diameter eases selection of holders and adaptors. For workshops streamlining tool change procedures, the bar’s compatibility with widely used insert geometries supports rapid deployment and consistent surface finishes. Discuss Teknik Cutting Tools’ TKB120TM with Metav Werkzeuge for a tailored recommendation and fast supply from Emmerich to the workshop bench Technical data Article number: TKB120TM Manufacturer: Teknik Makina Product: Boring tool Facts Max cutting diameter: 56 mm Shank diameter: 32 mm Cutting length (shank): 120 mm Overall length: 180 mm Weight: 1.528 kg Special features Insert type: CCMT 09T3 Nominal diameter: 45 mm Compatible with indexable inserts FAQ What insert type does this boring bar use? The TKB120TM is specified for CCMT 09T3 indexable inserts, allowing rapid edge changes and standardised insert stock. Which shank size is required for clamping? Clamping is based on a 32 mm shank; the TKB120TM’s shank diameter ensures firm mounting in suitable tool holders. What is the maximum cutting diameter available with the tool? The tool supports a maximum cutting diameter of 56 mm, with a nominal diameter entry of 45 mm for planning bore access. How long is the effective cutting length? The cutting length is 120 mm, while the overall bar length is 180 mm, providing a defined machining reach for internal operations. Is the TKB120TM suitable for quick tool changes in production environments? Yes — the TKB120TM’s use of indexable CCMT inserts and standard shank dimensions facilitates fast insert replacement and straightforward integration into existing tooling routines. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid, production-ready solution that combines stable clamping with quick insert compatibility; the robust shank and precise insert seat reduce downtime and maintain machining quality. Order directly via Metav Werkzeuge or consult the specialists for application advice. SIR S50U boring bar — SIR for IR indexable inserts by Teknik Cutting Tools The SIR S50U is a right-hand boring bar designed for heavy-duty turning with IR-compatible indexable inserts, optimised for stable clamping and consistent chip control SIR system for IR indexable inserts Shank Ø50 mm for rigid clamping Compatible with 22 IR inserts Overall length 350 mm, diameter 56 mm High rigidity for consistent machining The boring bar is engineered to keep vibration low and form tolerances tight in serial production. With a shank Ø50 mm, large cross-section and a diameter of 56 mm, the holder minimises deflection under cutting forces, which directly improves surface finish and reduces rework. Specified cutting geometry and the right-hand orientation mean predictable chip flow and repeatable results across workpieces. Fast, reliable insert changes to shorten cycle time Compatibility with 22 IR indexable inserts and the SIR clamping concept ensures secure seat engagement and rapid replacement. The clamping uses a Torx fastener system (Torx T15 with M4x15 screw) for reliable torque transmission, which reduces time at the machine and keeps changeover consistent on the shop floor. Clear interface features such as the U-plate TA063 and reference ring BSP010 support rapid set-ups and predictable positioning. Designed for production use and toolroom safety An overall length of 350 mm and a cutting height of 75 mm provide the reach required for medium-depth boring while retaining stiffness. The tool's mass (approx. 5.335 kg) contributes to damping during heavy cuts and stabilises the toolholder under variable loads. The ISO designation SIR S50U signals an industry-standard interface, facilitating inventory management and tool planning in CNC operations. Practical integration into machining systems The bar is supplied ready for assembly with the appropriate clamping interface for IR22 holders and works with commonly stocked indexable inserts, reducing procurement complexity. The standardised fasteners and locating features allow maintenance teams to replace consumables using conventional hand tools, improving uptime without specialised equipment. Specification clarity aids production planning and tool-life estimation. For a stable turning solution from Teknik Cutting Tools, ask Metav Werkzeuge for tailored recommendations and delivery from their Emmerich hub: info@metav-werkzeuge.com • +49 2822 7131930 Technical Data Article number: K346TM Model name: SIR S50U Product type: Boring bar / SIR for IR indexable inserts Manufacturer: Teknik Cutting Tools Core dimensions Shank diameter: 50 mm Overall diameter: 56 mm Cutting height: 75 mm Overall length: 350 mm Weight: 5.335 kg Compatibility & features Cutting direction: right-hand For indexable inserts: 22 IR Clamping system: SIR for IR inserts Clamping holder designation: IR22 U-plate: TA063 Pass ring: BSP010 Torx key: T15 Torx screw: M4x15 FAQ What insert type fits this boring bar? The SIR S50U accepts 22 IR indexable inserts and is configured for the SIR clamping interface to ensure correct seating and secure fixation. Is the bar suitable for heavy-duty turning? Yes; with a shank Ø50 mm, 56 mm diameter and a weight of 5.335 kg, the bar is intended to provide increased rigidity for heavier cuts and better vibration damping. How is the insert secured in the clamping seat? Insert retention is achieved via the SIR clamping system using a Torx T15 fastener and M4x15 screw, delivering consistent torque and reliable fixation. Can the bar be used on standard CNC turret toolposts? The ISO designation SIR S50U and standardised interface make the bar compatible with typical toolholding systems that accept IR22-style clamping holders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of broad taper compatibility, sturdy construction and precise dimensions for reliable tool holding in demanding CNC environments; order the milling arbor directly via Metav Werkzeuge or consult our specialists for application advice. Milling arbor ISO 25–27 – Teknik Makina M304TM with 57 mm shank The milling arbor M304TM from Teknik Makina is a tool-holder solution for industrial milling applications, designed for secure clamping and consistent performance with ISO 25–27 taper interfaces. ISO 25–27 taper for wide compatibility 154 mm total length for deep reach 57 mm tool shank diameter Robust construction, weight 3.617 kg Precise interface for consistent machining results A carefully engineered tool-holder interface ensures repeatable seating on standard ISO 25–27 taper spindles, which reduces setup time and supports consistent concentricity during machining. The combination of a defined taper and a 57 mm shank diameter delivers a predictable connection that helps to maintain precision across batches. For procurement and process planning, the quantified dimensions allow straightforward integration into tool lists and fixture checks, simplifying tool-change reasoning in production schedules. Stable mass and geometry for improved surface finish The arbor’s 154 mm overall length and measured mass (approx. 3.617 kg) contribute to mechanical damping and reduced vibrational sensitivity during heavy cuts. This stability supports better surface quality and longer cutter life by limiting deflection and runout fluctuation. In practice, a heavier, well-balanced holder can mean fewer reworks and more consistent tolerances, which translates into measurable gains in throughput and fewer scrap parts when machining demanding materials. Compatibility, handling and supply-chain confidence Delivered as a straightforward milling tool-holder, the M304TM fits standard tool-change procedures and is suitable where a robust, repeatable connection to the spindle is required. For workshops and production engineers seeking dependable supply, Metav Werkzeuge combines a broad product range with central European logistics, offering consistent availability and an experienced consultative approach. If clarification on fitment or tool selection is needed, Metav’s technical advisors can provide guidance tailored to the machining task and machine interface. For application-specific advice on the Teknik Makina M304TM milling arbor or to verify compatibility with existing spindle tooling, contact Metav Werkzeuge in Emmerich by e-mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical data Article number: M304TM Product type: Milling arbor Label: Fräseraufnahme ISO 25-27 Facts Shank diameter: 57 mm Total length: 154 mm Weight: 3.617 kg Special features Taper: ISO 25–27 Brand: Teknik Makina SKU: M304TM FAQ Is this arbor compatible with ISO 25–27 spindle interfaces? Yes. The milling arbor is designed specifically for ISO 25–27 taper connections and provides a standardised interface for compatible spindles. What are the key dimensions to check before ordering? Check the 57 mm shank diameter and 154 mm total length; these are the primary dimensions that determine fit and reach for the Teknik Makina M304TM. How does the weight affect machining performance? The approx. 3.617 kg mass helps to damp vibrations and improve stability during cutting, which can enhance surface finish and reduce tool wear. Can the arbor be used on different machine models? The arbor is suitable for machines that accept ISO 25–27 tapers; ensure the spindle interface and required reach match the M304TM dimensions. What information identifies this product in procurement systems? The SKU/article number M304TM and the designation “Milling arbor ISO 25–27” are the identifiers used for ordering and stock management. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust SIR S50U construction, high radial stiffness from a 50 mm shank, and precise compatibility with IR27 indexable inserts to maintain steady machining cycles and predictable tool life; order the tool directly via Metav Werkzeuge or contact our consultants for application advice. Boring bar K347-2TM — SIR S50U external turning bar, Ø58 mm, 350 mm A Boring bar K347-2TM engineered for external turning with indexable IR inserts, designed to deliver rigidity and repeatable results in industrial production environments SIR S50U design for IR27 indexable inserts Ø58 mm cutting diameter for external turning 50 mm shank for high radial stiffness 350 mm overall length, right‑hand orientation Rigidity and repeatability for heavy-duty turning The SIR S50U configuration provides a stable tool body that reduces chatter and deflection during external turning operations. With a 50 mm shank and a nominal cutting diameter of Ø58 mm, the bar is dimensioned to resist bending moments that commonly degrade surface finish and dimensional accuracy. This construction converts directly into predictable tolerances and less rework, which is particularly valuable for medium- to large-batch production where cycle-time consistency matters. The design for IR27 indexable inserts enables quick insert changes while maintaining the clamping integrity necessary for repeatable results. Geometry aligned to right‑hand cutting for efficient chip control Designed for right‑hand cutting, the bar positions the insert and clamp plate (TA065) for reliable chip evacuation and stable cutting angles. The specified cutting height of 75 mm ensures correct insert seating and positive engagement with the workpiece; this reduced risk of misalignment preserves the insert edge geometry and prolongs component life. The combination of geometry and clamping method supports efficient metal removal rates and lowers the risk of unexpected tool failure during continuous shifts, which contributes to overall productivity improvements on the shop floor. Practical handling, maintenance and integration into toolsets Assembly and maintenance are straightforward: clamping is secured with an M5x18 Torx screw (Torx key T20) and the holder designation IR27 supports common industrial insert packages, simplifying spare-part logistics. The bar’s 350 mm overall length and an item weight of 5.177 kg balance accessibility with mass that helps damp vibrations in demanding cuts. The ISO marking SIR S50U facilitates catalogue matching and tool management in ERP systems. When integrated into a standard tool carousel or turret, the bar’s interface and dimensions allow rapid setup and predictable offsets, reducing machine idle time between jobs. For production-critical turning with Teknik Cutting Tools’ SIR S50U concept, request a compatibility review from Metav Werkzeuge — Metav’s specialists in Emmerich can advise on insert grades, clamping torque and setup to match specific workpiece materials and cycle requirements. Technical data Article number: K347-2TM Name: Boring bar (SIR S50U) Type: SIR for IR indexable inserts Manufacturer: Teknik Makina Facts Diameter: 58 mm Shank diameter: 50 mm Overall length: 350 mm Cutting height: 75 mm Weight: 5.177 kg Direction: Right-handed Compatible inserts: 27 IR Torx key: T20 Torx screw: M5x18 Clamp plate: TA065 Special features ISO designation: SIR S50U Clamping designation: IR27 Designed for indexable inserts Right-hand cutting orientation Quick insert replacement capability FAQ What insert type fits this boring bar? The boring bar accepts IR27 indexable inserts; the tool is specified for IR27 clamping and the clamp plate TA065. Is the bar suitable for heavy cuts and high radial loads? The SIR S50U geometry with a 50 mm shank and Ø58 mm body offers elevated radial stiffness suited to heavier external turning, reducing deflection under load. How is the clamping secured and which tools are required? Clamping is secured by an M5x18 Torx screw, tightened with a T20 Torx key for reliable insert retention. Can the bar be used in automatic turret tool systems? Yes; the 350 mm overall length and standard ISO designation facilitate integration into common turret and tool post systems when offsets are set accordingly. What is the weight and does it affect handling? The item weight is 5.177 kg; the mass helps damp vibration but should be considered for manual handling and balance during rapid tool changes. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Specifications: Order Number: D684TM Item: Groving Holder usable with 5C MGM Indexable Inserts of Korloy Brand: Teknik Makina ISO Code: 3232 5C-R MGM Quantitative Characteristics: Weight: 1.268kg Total length: 150mm Additional Informattion Cutting Direction: rechts Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Take advantage of the adjustable 10°–80° angle range, the stable 25 mm shank and compatibility with TCMT 16T3 indexable inserts for precise, repeatable chamfering in production environments; order the cutter directly via Metav Werkzeuge or consult our experts for application advice. Adjustable Chamfer Cutter by Teknik Makina — 10°–80° angle, accepts TCMT 16T3 The Adjustable Chamfer Cutter is an indexable chamfering tool engineered for flexible bevel creation across a range of production and workshop tasks. Adjustable angle 10°–80° 25 mm shank for rigid clamping Max cutting diameter 34 mm Compatible with TCMT 16T3 inserts Flexible bevel control for varied chamfering tasks The adjustable design provides an immediate benefit in setups that require multiple bevels: the 10°–80° angle range permits rapid switching between shallow and steep chamfers without changing the tool body. This flexibility reduces downtime and simplifies tool inventories in small batches or mixed-production runs. The mechanism is optimised for repeatability, so every setting change maintains consistent edge geometry — important when tolerances are tight and finish quality matters. Rigid mounting and insert-based economy A 25 mm shank ensures secure clamping for stable cutting conditions, while a maximum cutting diameter of 34 mm defines the tool’s working envelope. Compatibility with TCMT 16T3 indexable inserts delivers the usual indexable-tool advantages: fast insert changes, consistent cutting edges and cost-efficient reconditioning compared with brazed cutters. The cutter is supplied with a Torx fastening system (M3.5×8.5 screw, T15 key) for reliable insert retention and straightforward maintenance. Practical handling and workshop integration Weighing just 0.37 kg, the tool balances ease of handling with industrial robustness, making it suitable for both bench-mounted operations and longer production runs where tool change ergonomics matter. The cutter’s modular concept supports standard indexable-insert workflows and simplifies spare-part logistics. For application-specific questions or to confirm fitment in a particular holder, Metav Werkzeuge can advise on the correct clamping and insert choices to match existing toolholders and machine systems. Contact Metav Werkzeuge for tailored application advice on the Teknik Makina adjustable chamfer cutter and secure reliable supply directly from Emmerich. Technical data Article number: AH15TM Manufacturer: Teknik Makina Designation: Adjustable chamfer cutter Core specifications Angle range: 10°–80° Max cutting diameter: 34 mm Shank diameter: 25 mm Weight: 0.37 kg Features and compatibility Inserts: TCMT 16T3 Torx screw: M3.5×8.5 Torx key: T15 Flexible holder designation: S1474 FAQ What angle range can be set with this cutter? The adjustable chamfer cutter by Teknik Makina can be set across a 10°–80° range to cover shallow to steep bevels. Which indexable inserts are compatible? Compatibility is specified for TCMT 16T3 inserts; the cutter uses these standard inserts for economical edge changes. What shank size is required for secure clamping? A 25 mm shank diameter provides the necessary rigidity for stable chamfering operations with this cutter. How is the insert secured on the cutter? Inserts are fastened with a Torx screw (M3.5×8.5) using a T15 key for reliable retention and simple servicing. Is the cutter suitable for production use? With a robust shank, indexable inserts and adjustable angles, the Teknik Makina chamfer cutter is intended for workshop and production environments where versatility and repeatability are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the tool's adjustable chamfering and internal coolant to improve cycle consistency and extend insert life; the compact 25 mm shank and 100 mm overall length provide straightforward machine integration. Order the adjustable chamfer cutter directly via Metav Werkzeuge or ask the consultants for tailored advice. Adjustable Chamfer Cutter AH15-1TM — for TCMT 16T3 Indexable Inserts, 5 mm cutting diameter The Adjustable Chamfer Cutter AH15-1TM is a compact, indexable‑insert cutter engineered for precise chamfering tasks in small and medium production environments, compatible with TCMT 16T3 inserts. Adjustable chamfering for TCMT 16T3 inserts 5 mm nominal cutting diameter Internal coolant for improved tool life Faster, repeatable chamfering for production runs The adjustable design with support for TCMT 16T3 indexable inserts delivers a cost‑effective route to repeatable chamfers without equipping multiple solid tools. Using interchangeable inserts reduces downtime for regrinding; replacing a worn indexable insert is faster than reconditioning a solid cutter, helping to maintain cycle times. The tool’s adjustable geometry enables fine tuning of the chamfer depth and angle, supporting consistent component quality across batches. Consistent cooling that prolongs service intervals Built‑in internal coolant directs lubricant and cooling fluid close to the cutting edge, which reduces thermal loading on the insert and evacuates chips more effectively. For operations where thermal stability influences dimensional accuracy, the coolant feed helps preserve cutting edge integrity and delays wear, translating into fewer insert changes and longer uninterrupted production windows. This characteristic supports predictable maintenance planning on the shop floor. Robust shank and compact dimensions for easy integration With a 25 mm shank and an overall length of 100 mm, the cutter fits standard holder systems without requiring special adaptors, simplifying tool changeover. The modest weight of 0.37 kg contributes to machine spindle balance at moderate speeds and facilitates handling during set‑up. A maximum cutting diameter of 34 mm establishes the tool’s capability envelope while the 5 mm nominal cutter size addresses typical chamfer profiles found in fabrication and finishing workflows. Practical benefits for purchasing and workshop managers The modular approach—indexable inserts on an adjustable body—lowers total cost of ownership by separating the wear‑sensitive cutting edges from the more durable tool body. Stocking a set of TCMT 16T3 inserts allows fast on‑site replacements and reduces lead times compared with bespoke solid tools. The design is suitable where flexibility and reduced tooling inventory are priorities, enabling efficient adaptation to varying component designs. For a tailored recommendation on machining parameters or to secure the Teknik Makina adjustable chamfer cutter AH15-1TM via Metav Werkzeuge, contact Metav Werkzeuge for professional advice and supply options. Technical data Article number: AH15-1TM Label: 5mm Fasenfräser, verstellbar TCMT 16T3 L100mm mit Innenkühlung Manufacturer: Teknik Cutting Tools / Responsible: Metav Werkzeuge GmbH Facts Nominal diameter: 5 mm Maximum cutting diameter: 34 mm Shank diameter: 25 mm Overall length: 100 mm Weight: 0.37 kg SKU: AH15-1TM UID: AH15-1TM Special features Adjustable chamfer cutter design Compatible with TCMT 16T3 indexable inserts Internal coolant/feed-through coolant Compact shank for standard tool holders FAQ What inserts does this cutter accept? The cutter is designed for TCMT 16T3 indexable inserts and uses the standard insert geometry associated with that designation. Is coolant supported through the tool body? Yes, the tool features internal coolant to deliver cutting fluid close to the insert for better thermal control and chip evacuation. What are the main dimensions to check for holder compatibility? Key dimensions are the 25 mm shank diameter and 100 mm overall length, which determine holder fit and projection. Can worn inserts be replaced on the cutter? Worn TCMT 16T3 inserts can be removed and replaced on the cutter body without additional machining, enabling rapid tool service. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of adjustable chamfering, internal coolant and compatibility with TCMT 1102 indexable inserts for consistent, burr-free bevels in serial production; order the cutter directly via Metav Werkzeuge or consult our specialists for application advice. Adjustable Chamfer Milling Cutter AH10-1TM — 5 mm diameter, internal coolant (Teknik Makina) A compact adjustable chamfer milling cutter AH10-1TM designed for precise beveling with TCMT 1102 indexable inserts, optimised for repeatable edge preparation in workshop and production environments Adjustable chamfering for versatile bevel widths Internal coolant supply for improved tool life Shank Ø20 mm for secure, stable clamping Compatible with TCMT 1102 indexable inserts Precision chamfering that reduces rework The adjustable chamfering concept delivers reliable bevel widths without multiple tools, making setup more efficient and reducing rework. The tool is designed around the proven TCMT 1102 indexable inserts, so insert changes are quick and economical. As a result, process consistency is improved and cycle times are shortened. This configuration makes the cutter particularly suitable where repeatable edge geometry is required across batches, helping to maintain part tolerances with minimal intervention. Better cutting conditions with internal coolant Integrated internal coolant channels feed cutting fluid directly to the cutting zone, improving chip evacuation and cooling at the insert edge. The immediate cooling reduces thermal loading on the insert, which contributes to longer tool life and a superior surface finish on bevelled edges. The combination of a compact cutter body and coolant supply supports stable cutting at the specified dimensions, including a cutting diameter 27 mm and an overall length 100 mm, while keeping vibrations low through the shank Ø20 mm connection. Economical handling thanks to indexable inserts The use of indexable inserts makes servicing straightforward: worn cutting edges are replaced rather than the entire tool, cutting consumable costs and minimising downtime. The insert system supports rapid restoration of cutting performance and consistent geometry. For operations that value uptime and predictable maintenance schedules, the replaceable-insert approach offers a clear cost-benefit compared with solid-tool alternatives and keeps capital equipment utilisation high. Application flexibility for workshop and light production This adjustable chamfer cutter excels in tasks that require clean, precise bevels on metal components where a dedicated chamfering operation is needed. The compact design is suitable for integration into standard toolholders that accept a shank Ø20 mm connection. The product is identified as AH10-1TM and is manufactured by Teknik Makina; it complements typical cutting tool inventories and supports mixed-production environments where rapid changeover between operations is essential. Speak to Metav Werkzeuge for technical consultation on the AH10-1TM and fast supply from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: AH10-1TM Label: 5mm Fasenfräser, verstellbar TCMT 1102 L100mm mit Innenkühlung Manufacturer: Teknik Makina Measurements Diameter: 5 mm Maximum cutting diameter: 27 mm Overall length: 100 mm Shank diameter: 20 mm Weight: 0.241 kg Features Compatibility: TCMT 1102 indexable inserts Internal coolant: yes Adjustable chamfering Indexable insert system SKU for ordering: AH10-1TM FAQ Which indexable inserts are suitable for this cutter? The cutter uses TCMT 1102 inserts; the AH10-1TM is designed to accept these standard indexable inserts for easy replacement. How does the internal coolant improve performance? Internal coolant channels deliver fluid directly to the cutting edge, which helps the AH10-1TM maintain cutting stability, extend insert life and improve surface finish. What holder size is required for secure mounting? The cutter features a shank Ø20 mm, so a toolholder or collet that accepts a 20 mm shank is required for stable clamping. Can the chamfer width be adapted during production? Yes, the adjustable design allows adaptation of bevel dimensions to meet varying chamfer requirements without changing to a different cutter. What are the order reference and weight for logistics planning? Order under SKU AH10-1TM; the cutter weight is 0.241 kg. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, reliable tool that combines 5 mm accuracy with easy handling to keep assembly and maintenance tasks moving smoothly; lightweight construction at 0.1 kg reduces operator fatigue and supports fast, repeatable tightening. Order directly via Metav Werkzeuge or consult our team for specific workshop applications. Allen key (5 mm) — compact hex key for workshop fastening, Teknik Makina The Allen key is a compact hex wrench designed for precise fastening in assembly, maintenance and general workshop applications Compact 5 mm hex key for precise fastening Lightweight: only 0.1 kg for easy handling Robust workshop tool by Teknik Makina Precision fastening where space is limited The compact 5 mm shaft and hex profile enable accurate torque transfer for small fasteners, making this tool suitable for confined or recessed fixings. Its minimal profile supports access to tight joints while the standard hex geometry ensures consistent contact with the fastener head, reducing cam‑out and rounding. The emphasis is on precision and repeatability, so routine assembly and maintenance cycles remain efficient and traceable with every twist. Practical design for efficient workshop use A lightweight tool at 0.1 kg, this hex key reduces hand fatigue during repetitive operations and speeds up small‑part assembly tasks. The simple form factor eliminates unnecessary bulk on the workbench and integrates well with existing tool sets. By favouring straightforward geometry over complex mechanisms, the tool promotes a low‑maintenance workflow that aligns with lean workshop practices and reliable day‑to‑day performance. Easy handling, storage and trusted provenance The compact profile supports tidy storage and rapid retrieval from tool boards or racks, improving process flow between jobs. Supplied under the Teknik Makina label, this hex key benefits from a clear, production‑orientated design suited to industrial and trade environments. The focus remains on dependable operation and practical usability, providing craftsmen and technicians with a straightforward, compact design that complements precision tool collections. Consider the Teknik Cutting Tools 5 mm Allen key for consistent small‑fastener work — contact Metav Werkzeuge for availability and application advice Technical Data Article number: 5ALLENTM Designation: Allen key Size indication: 5 Facts Weight: 0.1 kg ECLASS: 21189290 SKU: 5ALLENTM Special features Tool type: Allen key (hex key) Brand: Teknik Makina Compact form for confined spaces FAQ What size is the tool and what does it fit? The tool is a 5 mm Allen key; it fits fasteners with a 5 mm internal hex profile and is intended for small assembly and maintenance tasks. Is the Allen key suitable for workshop and industrial applications? Yes, the 5 mm hex key from Teknik Makina is designed for workshop use and repetitive fastening where a compact, reliable hex wrench is required. How heavy is the tool and does it aid repetitive work? Weighing approximately 0.1 kg, the Allen key reduces hand fatigue during repetitive operations while maintaining secure contact with the fastener. Can the 5ALLENTM be integrated into a standard tool set? The 5ALLENTM Allen key is compact and designed for easy storage on tool boards or in sets, making it straightforward to add to existing collections. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise chamfering, robust clamping and Korloy compatibility for consistent production results; order the chamfer cutter directly via Metav Werkzeuge or ask our consultants if needed. 5 mm Chamfer Cutter L130 mm – Teknik Makina, 2 flutes, 32 mm shank A 5 mm chamfer cutter L130 mm designed for accurate edge preparation and light chamfering tasks in machining applications, suitable for use with Korloy indexable inserts. 5 mm cutting diameter for precise chamfers 130 mm overall length for deep reach 32 mm shank for secure clamping Compatible with Korloy indexable inserts Accurate chamfering that reduces rework and increases throughput The chamfer cutter delivers controlled edge formation with a 5 mm cutting diameter that is optimised for small, precise chamfers. The geometry of the cutting edges and the two-flute design focus on repeatable results, reducing the need for downstream deburring and rework. By standardising on a cutter that produces uniform chamfer profiles, shops can expect improved cycle consistency and a measurable uplift in overall process efficiency. Stability and runout control for cleaner finishes A substantial 32 mm shank provides the mechanical stability required for steady cutting, while the two cutting edges support a balanced tool load. The tool requires a T15 Torx key to secure the insert screw (type M3,5x11), which aids quick indexing and replacement when service is necessary. The combination of a robust shank and compact cutter head minimises vibration and runout, resulting in a cleaner finish and longer tool life under normal operating conditions. Designed for versatile chamfering tasks in production environments Engineered for edge preparation, bevel creation and light deburring, this cutter is compatible with Korloy indexable inserts to offer a cost-effective approach to consumable management. The overall length 130 mm and a cutting length 50 mm provide access to workpieces with restricted reach while maintaining sufficient engagement for stable cutting. The solution is suitable for batch production and workshop retooling where predictable chamfer geometry is an operational requirement. Practical handling and workshop integration Maintenance and insert changes require only a standard Torx drive; the specified T15 Torx interface and M3,5x11 screw form a simple, proven fastening method that supports rapid servicing. The cutter is identified as S359TM, enabling straightforward inventory tracking and reordering. Supplied through Metav’s distribution, the tool benefits from a European quality filter and reliable logistics, helping to keep toolrooms stocked and production uninterrupted. For robust, repeatable chamfers with Teknik Makina reliability, contact Metav Werkzeuge for technical advice and procurement — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: S359TM Manufacturer: Teknik Makina Product type: Chamfer cutter Article label: 5mm Fasenfräser L130mm Dimensions & core data Diameter: 5 mm Overall length: 130 mm Shank diameter: 32 mm Cutting length: 50 mm Number of flutes: 2 Features & compatibility Compatible with Korloy indexable inserts Torx key: T15 Torx screw: M3,5x11 ECLASS: 21180806 Category: Machining / Shank cutters FAQ What material systems is this cutter suitable for? The cutter S359TM from Teknik Makina is intended for general chamfering tasks; compatibility with specific materials depends on the chosen Korloy insert grade and machining parameters. How is the insert fastened and exchanged? Insert fixation uses a Torx screw M3,5x11 requiring a T15 Torx key; the S359TM design allows straightforward screw removal for rapid insert changes. What advantages does the 32 mm shank provide? A 32 mm shank increases clamping stability and reduces tool deflection, improving finish and dimensional consistency during chamfering operations. Can this cutter reach recessed or hard-to-access edges? With an overall length of 130 mm and a cutting length of 50 mm, the tool is configured to access moderately recessed edges while maintaining cutting stability. How many cutting edges does the cutter have and why does it matter? The tool features two flutes; this configuration balances chip evacuation and cutting stability for small to medium chamfer profiles. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of compatibility with XCET 3104 indexable inserts, precise 5 mm chamfering and a 32 mm shank for stable clamping — all designed to keep production flowing with minimal downtime. Order the tool directly via Metav Werkzeuge or ask the consultants for application advice. Chamfer Cutter S357TM (for XCET 3104 Indexable Inserts) — 5 mm, L 130 mm — Teknik Makina A chamfer cutter designed for use with XCET 3104 indexable inserts, intended for precision chamfering and bevel preparation in milling applications. Compatible with XCET 3104 inserts 5 mm cutting diameter 32 mm shank for stable clamping 130 mm overall length Precision chamfering with indexable inserts The tool is engineered for repeatable chamfering thanks to its use of XCET 3104 indexable inserts, which allow rapid replacement and consistent cutting geometry across production runs. With a 5 mm cutting diameter, the cutter provides a controlled chamfer width that simplifies downstream assembly and finishing. The replaceable insert system reduces tool-change time, lowering machine downtime and improving overall process efficiency. The combination of indexed inserts and a single, well-defined cutting edge gives predictable chip formation and a reliable surface finish. Rigidity and runout control for consistent edge quality Clamping stability has been prioritised: the 32 mm shank and the substantial overall length of 130 mm are balanced to offer both reach and torsional rigidity in typical milling setups. A 50 mm cutting length ensures sufficient engagement for bevel operations while limiting overhang to reduce runout. These dimensions contribute to uniform results part after part, particularly in setups where consistent chamfer depth and angle are essential. Stable clamping reduces vibration, which in turn preserves insert life and lowers scrap rates. Fast maintenance and secure fixing for industrial workflows Insert retention and serviceability are straightforward: the cutter uses a Torx retention screw M3.5x11, tightened with a T15 key, enabling quick and secure insert changes on the shop floor. Compatibility with Korloy insert variants offers flexibility in sourcing and grade selection according to the material being machined. The tool’s single cutting edge simplifies inspection and seating of the insert, making routine maintenance fast and predictable, which supports tight production schedules and well-ordered tool management. Suitable tasks and operational benefits Best placed in CNC milling and secondary chamfering operations, this chamfering tool improves edge preparation prior to welding, coating or assembly. The design supports high repeatability and easy integration into existing tool inventories that include XCET 3104 inserts. For procurement and logistics, Metav Werkzeuge provides centralised distribution and a quality filter from Emmerich, helping to reduce supplier complexity while ensuring reliable supply. The result is a pragmatic tool choice for workshops seeking to optimise cycle times and maintain consistent edge quality. For technical consultation on toolholder compatibility or to secure supply of the S357TM chamfer cutter from Teknik Makina, contact Metav Werkzeuge for tailored advice and prompt delivery from Emmerich. Technical data Article number: S357TM eClass: 21180806 Product type: Chamfer cutter Facts Diameter: 5 mm Overall length: 130 mm Shank diameter: 32 mm Cutting length: 50 mm Cutting edges: 1 Torx screw: M3.5x11 Torx key: T15 Special features Compatible with XCET 3104 indexable inserts Suitable for Korloy inserts Tool category: Shaft cutters (Schaftfräser) Manufacturer: Teknik Makina FAQ Which inserts fit this cutter? The cutter accepts XCET 3104 indexable inserts; it is compatible with Korloy grades for varied material applications. What are the critical dimensions for toolholding? The tool has a 32 mm shank and 130 mm overall length; ensure a matching toolholder for stable clamping and minimal runout. How are the inserts secured? Inserts are fixed with a M3.5x11 Torx screw and tightened using a T15 key for secure retention and rapid replacement. What machining tasks is the cutter intended for? Designed for precision chamfering and bevel preparation in milling operations, the cutter supports repeatable edge preparation prior to assembly or finishing. What is the cutting engagement length? The tool provides a 50 mm cutting length, suitable for many chamfering and secondary machining tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of 5 mm cutting diameter, a 32 mm shank and a 130 mm overall length for stable, repeatable chamfering in series production; order the tool directly via Metav Werkzeuge or contact our consultants for application support. Teknik Makina Chamfer Cutter S358TM – 5 mm dia, L130 mm A Chamfer Cutter S358TM designed for precise edge preparation and fast insert changes in industrial milling and finishing processes. 5 mm cutting diameter 32 mm shank diameter Two cutting edges for clean chamfers Compatible with Korloy indexable inserts Consistent, repeatable chamfering for reduced rework The S358TM shaft-mounted chamfer cutter delivers controlled edge preparation where dimensional consistency matters. With a 5 mm cutting diameter and two cutting edges, the tool produces uniform chamfers that minimise secondary deburring and manual finishing work. For workshops aiming to tighten tolerances and reduce throughput variability, the cutter’s geometry supports reliable cycle times and predictable tool wear. The result is fewer rejects and shorter downstream processing, which directly benefits productivity planning in high-volume environments. Stable clamping and vibration reduction for better surface finish A 32 mm shank and a total length of 130 mm provide enhanced rigidity in most standard collet or chuck systems. This robust shank diameter reduces deflection during machining, helping to maintain a consistent cutting angle over the full length of the operation. The 50 mm cutting length balances reach with stiffness, enabling clean chamfer edges even on longer toolpaths. In practice, improved stability lowers the risk of chatter, optimises surface quality and prolongs the life of both the insert and the holder. Fast, secure insert changes and simple maintenance Designed for compatibility with Korloy indexable inserts, the tool streamlines insert replacement and reduces downtime. The insert is secured with an M3.5x11 Torx screw, tightened with a T15 Torx drive for repeatable clamping torque. This standardised fixing simplifies maintenance routines and spare-part management across mixed fleets. Clear, repeatable fastening reduces assembly errors and makes it easier to train workshop staff on correct insert handling, supporting consistent process reliability. Practical applications and process advantages This chamfer cutter is suited to precision chamfering and edge breaking in preparation for assembly, welding or coating. By integrating a dedicated chamfering tool into the machining sequence, shops can consolidate operations and cut overall cycle time. The design focuses on practical, measurable benefits: reproducible edge geometry, straightforward insert swaps and reduced operator intervention. For production-oriented environments that require dependable tooling, the S358TM contributes to smoother workflow and predictable output. For availability, specification matching or machining recommendations for the Teknik Makina chamfer cutter S358TM contact Metav Werkzeuge in Emmerich — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical Data SKU: S358TM Label: 5mm Fasenfräser L130mm Manufacturer: Teknik Cutting Tools Facts Diameter: 5 mm Overall length: 130 mm Shank diameter: 32 mm Cutting length: 50 mm Number of cutting edges: 2 Torx screw: M3,5x11 Torx key size: T15 Special features Compatible with Korloy indexable inserts Shaft-mounted chamfer cutter design Suitable for industrial milling and finishing FAQ What cutting diameter does the tool use? The chamfer tool has a 5 mm cutting diameter, suitable for small, precise chamfers. Which shank size is required for clamping? The tool uses a 32 mm shank diameter, designed for stable clamping in compatible collets or holders. Which inserts are compatible with this cutter? The cutter is compatible with Korloy indexable inserts and uses an M3.5x11 Torx screw for secure fastening. What is the article number or SKU? The article number is S358TM, sold under the Teknik Makina chamfer cutter designation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid chamfering solution that combines compatibility with TCMT 1102 indexable inserts and dual-angle chamfering (60° / 120°) for versatile edge preparation; order the tool directly via Metav Werkzeuge or consult the experts for application advice. Chamfer mill S335-1TM — Chamfering cutter for TCMT 1102 indexable inserts, Ø5 mm, L70 mm (Teknik Makina) The Chamfer mill S335-1TM is a purpose-built chamfering cutter for machining precise 60° and 120° chamfers using TCMT 1102 indexable inserts, suitable for CNC and toolroom operations. Compatible with TCMT 1102 indexable inserts Dual chamfer angles 60° and 120° 12 mm shank for secure clamping Compact 70 mm overall length Precise chamfers with an insert-based system that saves time The S335-1TM is engineered for repeatable chamfering using industry-standard indexable inserts. Its compatibility with TCMT 1102 inserts means insert replacement is fast and cost-effective compared with brazed tooling, while the dual-angle capability (60° and 120°) allows a single tool to cover multiple chamfer profiles. With a nominal diameter of Ø5 mm and a maximum cutting diameter of Ø16 mm, the cutter provides a flexible work range that reduces tool changes and increases uptime on batch runs. Short, rigid design that improves surface quality and stability A 12 mm shank combined with a 70 mm overall length keeps the toolholder engagement high and minimises overhang, which in turn reduces vibration and improves surface finish. The low mass (approx. 0.182 kg) contributes to dynamic stability at typical machining speeds, helping to extend insert life and maintain consistent edge geometry. These factors together result in measurable gains in process reliability and predictable cycle times for production environments. Fast serviceability with standard fixation components Maintenance and insert changes are straightforward: the cutter uses a Torx fastening system (key Torx T8) and M2.5x5.5 fixing screws, ensuring secure clamping and simple re-indexing of the single cutting edge. The single-edge arrangement simplifies insert handling and inventory, lowering the risk of assembly errors during changeover. Clear identification (SKU S335-1TM) streamlines replenishment and tool management in busy toolrooms. Designed for industrial chamfering tasks and flexible workflows This chamfering tool is aimed at workshops and CNC operations seeking a reliable insert-based option for edge preparation. By combining a compact form factor with standardised inserts, the cutter supports lean tooling strategies and reduces dependency on specialist brazed cutters. The result is a pragmatic balance of precision, convenience and predictable maintenance intervals, making it suitable for repeated chamfering, edge breaking and preparatory finishing in assembly-ready components. For tailored application advice or to purchase the Teknik Makina S335-1TM, contact Metav Werkzeuge for expert guidance and secure supply directly from Emmerich. Technical data Article number: S335-1TM Label: 5mm Fasenfräser TCMT 1102 L70mm Manufacturer: Teknik Makina Facts Nominal diameter: 5 mm Maximum cutting diameter: 16 mm Shank diameter: 12 mm Overall length: 70 mm Weight: 0.182 kg Cutting edges: 1 Chamfer angles: 60°, 120° Special features Compatible with TCMT 1102 indexable inserts Torx key: T8 Torx screw: M2.5x5.5 SKU: S335-1TM FAQ What inserts does the cutter accept? The S335-1TM accepts TCMT 1102 indexable inserts, enabling quick insert swaps and standardised replenishment. Can the tool produce both 60° and 120° chamfers? Yes, the cutter is designed for 60° and 120° chamfers, providing flexibility for different edge profiles. What shank diameter is required for the holder? The tool features a 12 mm shank, suitable for compatible collets and toolholders in the same diameter class. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com