Gibt es einen Hahn und Kolb Online Shop?

Take advantage of the combination of precise T-slot geometry, robust 32 mm shank support and rapid indexable-insert replacement for uninterrupted production. Order the T‑slot cutter directly via Metav Werkzeuge or request advice from the technical consultants for tailored application guidance. T‑nut cutter TKC050TM — 50 mm diameter, 7‑flute T‑slot milling cutter by Teknik Makina The T‑nut cutter TKC050TM is a purpose‑built tool for accurate T‑slot and T‑nut machining in general workshop and industrial milling applications, designed to deliver repeatable slot geometry with quick insert changes. 50 mm diameter for wide T‑slots 7 flutes for stable chip control 32 mm shank for rigid clamping 45 mm cutting length for deep slotting Consistent slot geometry for reliable assembly This T‑slot mill is engineered to produce precise T‑slot profiles with a stable cutting edge arrangement. The combination of a 50 mm diameter and 7 flutes reduces vibration and promotes uniform chip evacuation, which in turn helps maintain profile accuracy over serial runs. For customers seeking repeatable fitting results in fixtures and workholding, the tool’s balanced flute count offers an effective compromise between surface finish and removal rate. The cutting head is secured with a Torx fastener system to simplify insert replacement, while the robust 32 mm shank supports high clamping rigidity and reduces the risk of runout during heavy passes. Optimised for productivity and straightforward insert servicing Designed with workshop efficiency in mind, the tool supports rapid insert changes and minimal downtime. The cutter is supplied with a Torx screw (M2x4.2) and requires a T6 Torx key, ensuring secure and fast replacement of indexable inserts from compatible manufacturers. With a 45 mm cutting length and a 5 mm cutting height, the tool is suitable for moderately deep T‑slot operations without compromising stability. The overall length of 120 mm and a relatively low mass (0.83 kg) make the cutter easy to handle during tool changes and storage, while still providing the necessary reach for most vertical and horizontal milling setups. Material compatibility and application profile The cutter’s geometry and construction make it suitable for a broad range of general metalworking tasks where T‑slot milling is required. Its flute geometry aids chip control across typical ferrous and non‑ferrous workpieces commonly encountered in fixture manufacture and machine bed modification. Compatibility with established insert manufacturers, including Taegutec, simplifies procurement and gives access to a range of grades for different materials and cutting conditions. The result is a tool that supports both one‑off and small‑batch production environments with a focus on consistent fit and reduced rework. Installation, handling and expected benefits Fitted into a suitable toolholder with the 32 mm shank, the cutter performs best when clamped with minimal overhang and correct axial support. The indexed insert system means that minor edge wear can be addressed by simple indexing or replacing the insert, avoiding full‑tool replacement and lowering operating costs. Users will appreciate the balance between cutting capacity and user‑friendly maintenance: faster changeovers and fewer interruptions translate into improved shop throughput and predictable part quality. Documentation and technical drawings are recommended for integration into process planning and NC programming. For technical consultation on integrating the 50 mm T‑slot cutter into production, contact Metav Werkzeuge for expert advice and dependable delivery from Emmerich. Technical data Article number: TKC050TM Manufacturer: Teknik Makina ECLASS: 21180605 ETIM: EC011860 Core data Diameter: 50 mm Flutes: 7 Overall length: 120 mm Shank diameter: 32 mm Cutting length (shank): 45 mm Cutting diameter at shank: 31.5 mm Cutting height: 5 mm Weight: 0.83 kg Special features T‑slot cutter for machining T‑nuts and T‑slots Compatible with Taegutec indexable inserts Torx screw M2x4.2 for insert clamping Torx key required: T6 SKU: TKC050TM FAQ Which insert brands fit this T‑slot cutter? The TKC050TM is specified for use with compatible indexable inserts; it is listed as compatible with Taegutec inserts and will accept inserts from manufacturers following the same seat geometry. What shank size and holder are required? The cutter has a 32 mm shank; a rigid toolholder sized for a 32 mm shank and minimal overhang is recommended to ensure optimal runout and finish. How deep can the cutter machine a T‑slot in one pass? The tool provides a 45 mm cutting length and a 5 mm cutting height; maximum single‑pass depth should be selected based on material, insert grade and machine rigidity to avoid overload. How is the insert secured and replaced? Inserts are secured with a Torx screw (M2x4.2) and require a T6 Torx key for removal and fitting, enabling quick and secure insert changes. Is the TKC050TM suitable for serial production? Yes, the cutter’s multi‑flute design and robust shank support are intended to deliver consistent results in serial and small‑batch production, reducing rework and downtime. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust, indexable design that combines a 50 mm cutting diameter with a 25 mm shank for stable clamping and precise slot profiles; the tool accepts MGM 4C indexable inserts for fast changeovers. Order via Metav Werkzeuge or consult our specialists for setup recommendations. T-slot cutter TKC303TM — 50 mm diameter, two cutting edges · Teknik Makina The T-slot cutter TKC303TM is an indexable T-slot milling cutter designed for precise slotting in fixtures, machine tables and profile systems. 50 mm cutting diameter for deep T-slots 25 mm shank ensures rigid clamping Accepts MGM 4C indexable inserts (Korloy) Two cutting edges for efficient material removal Accurate slot profiles with indexable inserts for consistent output The TKC303TM delivers repeatable results through its indexable inserts concept. Using replaceable MGM 4C inserts from Korloy reduces downtime compared with solid tools: worn edges are swapped without removing the toolholder, shortening cycle interruptions. The combination of a wide cutting diameter and a two-edge geometry yields stable cutting forces and predictable chip formation, which contributes directly to improved surface finish and dimensional conformity in batch production. Rigid shank and geometry that stabilise machining A 25 mm shank and a balanced tool body length provide the rigidity required for accurate slotting operations. With a 120 mm overall length and a cutting height 4 mm, the cutter maintains concentricity and reduces chatter when clamped correctly, resulting in lower rework rates. The measured distance from cutting edge to shank (12.75 mm) helps planners assess reach and clamping overlap for fixture design, making the tool suited to integrated fixtures where stability is paramount rather than long overhangs. Practical workflow integration and low-maintenance handling The indexable design and compatibility with standard insert geometries simplify inventory: stock the MGM 4C inserts instead of multiple full-diameter cutters. Fast securing via an M8 clamping screw and an Allen key reduces changeover time at the machine, while the two-edge configuration balances material removal and tool life for routine production cycles. This cutter is positioned for operations that favour predictable throughput, minimal setup complexity and straightforward in-shop maintenance. For tailored tooling recommendations and to arrange supply from our Emmerich hub for the Teknik Makina TKC303TM, contact Metav Werkzeuge by phone or e‑mail for specialist advice and delivery planning Technical data SKU: TKC303TM Name: T-slot cutter (T-Nut Fräser) Manufacturer: Teknik Makina Brand: Teknik Cutting Tools Weight: 0.536 kg Insert type: MGM 4C Compatible insert manufacturer: Korloy Clamping screw: M8 Wrench/key: 6 mm Allen Facts Diameter: 50 mm Shank diameter: 25 mm Number of cutting edges: 2 Overall length: 120 mm Cutting height: 4 mm Distance cutting edge to shank: 12.75 mm Weight: 0.536 kg Special features Indexable insert system (MGM 4C) Compatible with Korloy insert geometries Round milling cutter body Secured with M8 clamping screw and 6 mm Allen key FAQ Which inserts are compatible with this cutter? The TKC303TM accepts MGM 4C indexable inserts and is designed to work with Korloy insert geometries. What are the key dimensions and securing method? The TKC303TM has a 50 mm diameter, 25 mm shank, 120 mm overall length and a 4 mm cutting height; inserts are fixed with an M8 clamping screw using a 6 mm Allen key. How many cutting edges does the tool have and what is the benefit? Equipped with two cutting edges, the tool balances efficient material removal with smooth slot walls, supporting repeatable cycle times with the TKC303TM. Can the cutter be used with standard 25 mm tool holders? The 25 mm shank of the TKC303TM is compatible with holders and collets sized for 25 mm shafts; verification of holder specs is recommended prior to use. What maintenance is recommended for long life? Regular inspection of insert condition and secure clamping of the M8 screw keeps the TKC303TM serviceable; replace worn inserts promptly to maintain slot quality. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise T-slot production with a 50 mm diameter cutter and a 25 mm shank that keeps set-up fast and stable; the indexable RHKW 1003 inserts deliver efficient material removal and predictable tool costs. Order directly via Metav Werkzeuge or consult our specialists for cutting data and compatibility advice. T-slot milling cutter TKC202TM — 50 mm diameter, 25 mm shank (Teknik Makina) The T-slot milling cutter TKC202TM is an indexable-insert tool designed for producing accurate T-slots in machine tables, fixtures and profile systems within CNC and workshop environments 50 mm diameter for deep T-slots 25 mm shank for secure clamping Quick indexable insert change with Torx T15 Compatible with Ingersoll RHKW 1003 inserts High-precision slotting with efficient set-up The cutter combines a 50 mm diameter cutting head with five active flutes to create true T-slot profiles with consistent geometry. Using indexable inserts rather than solid cutters reduces per-edge cost and simplifies maintenance: worn edges are replaced, not the whole tool. The compatible RHKW 1003 insert format is common in industry, so insert stocking is straightforward and repeatable machining tolerances are easier to achieve. Fast insert changes reduce production downtime Designed for rapid maintenance, the tool uses a Torx T15 interface for the main fastenings and a M4x10 Torx screw for secure insert clamping; the primary locking is managed via an M3.5 locking screw. These standard fasteners allow quick, safe insert replacement with minimal operator training and no complex torque devices. The result is less machine downtime, faster shift handovers and a simplified tool-change routine on the shop floor. Robust shank and compact form for reliable clamping A 25 mm shank diameter provides solid engagement in standard collets and toolholders, keeping run-out low during heavy cuts. The cutter’s 100 mm overall length and balanced mass (approx. 0.284 kg) make it suitable for both small CNC milling centres and larger production machines alike. Compatibility with Ingersoll insert geometries ensures interchangeability with established indexable systems and helps reduce tooling variants in the tooling cabinet. Practical benefits for machining operations With five cutting edges, this cutter achieves stable chip formation and consistent slot profiles, which benefits repeatable assembly and fixturing accuracy. Selection of appropriate cutting parameters and coolant strategy will define surface quality and tool life; for guidance on optimal feed rates and speeds for specific materials, Metav specialists can provide application-oriented recommendations. The TKC202TM’s modular approach to inserts keeps lifecycle costs under control while ensuring predictable production output. Discuss machining requirements and secure shipment from Metav Werkzeuge for the Teknik Makina TKC202TM — contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: TKC202TM Manufacturer: Teknik Makina Product name: T-slot milling cutter Core data Diameter: 50 mm Shank diameter: 25 mm Overall length: 100 mm Cutting edges: 5 Weight: 0.284 kg Special features Suitable for indexable inserts RHKW 1003 Compatible with Ingersoll insert systems Torx screw M4x10 for insert clamp Torx key size T15 M3.5 locking screw FAQ Which inserts fit this cutter? The TKC202TM accepts indexable inserts in the RHKW 1003 format; compatibility with Ingersoll-type inserts is specified for standard fit and repeatability. How many cutting edges does the cutter have? The tool is built with five active cutting edges, providing steady chip evacuation and smooth slot geometry. What shank diameter is required for toolholding? A 25 mm shank is provided, designed for secure clamping in common collets and holders used on CNC milling machines. What fasteners are used for insert clamping? Insert clamping uses a M4x10 Torx screw with a Torx T15 interface; the tool also includes an M3.5 locking screw for secure retention. Is the cutter suitable for production environments? Yes — the TKC202TM’s indexable design, standard fasteners and 25 mm shank make it well suited to repeated production work and quick tooling changes Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah. 422 Nolu Sokak No: 9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact solution that pairs 50 mm cutting capacity with secure clamping via a 32 mm shank, and benefits from straightforward insert changes for continuous shop-floor productivity — order the tool directly via Metav Werkzeuge or contact our consultants for application advice. T-slot cutter TKC060TM — 50 mm diameter, 32 mm shank (Teknik Makina) The T-slot cutter TKC060TM is a robust milling tool designed for efficient production and maintenance of T‑slots in workshop environments, combining a compact overall length with indexable‑insert convenience 50 mm cutting diameter for deep T‑slots Compatible with SPMG 06 indexable inserts 32 mm shank for high clamping rigidity Quick insert fastening with M2.2x5 Torx screws Precision and rigid clamping for repeatable slots The cutter delivers consistent geometry thanks to its 50 mm nominal diameter and 6 cutting edges, which are arranged to produce clean, repeatable T‑slot profiles. The combination of a 32 mm shank and a 120 mm overall length offers a balance between accessibility and stability; the substantial shank diameter reduces deflection and run‑out, which preserves profile accuracy in serial machining. With a 45 mm cutting length and a cutting height of 8 mm, the tool is dimensioned to create deep T‑slots while maintaining cutter life and process reliability. Operators and process engineers will recognise the benefit of a tool that prioritises dimensional control over long production runs. Reduce downtime with indexable‑insert efficiency This cutter uses SPMG 06 indexable inserts, making edge replacement rapid and economic. Asserts of insert technology mean that only the insert needs replacement when wear occurs, avoiding the need to change the entire cutter body and minimising downtime. The insert pockets are secured with M2.2x5 Torx screws, tightened with a T7 key, which standardises the maintenance routine and shortens service intervals. Compatibility with Taegutec‑style inserts broadens sourcing options for spare parts, supporting lean inventory management and predictable tool‑cost planning for production managers. Simple integration into existing tool systems Installation is straightforward: the 32 mm shank fits conventional toolholders and collets rated for that diameter, and the cutter’s 0.839 kg mass helps preserve balance across typical spindle speeds used for slotting operations. The cutter’s geometry and insert format allow it to be slotted into established tool assemblies without extensive modification, while the rugged design supports repeated indexing cycles. For quieter changeovers and reliable torque transmission during mounting, standard workshop torque practices are recommended and routine inspection of the Torx screws keeps the system secure. The overall design focuses on ease of integration for maintenance, retrofit, or new‑build machining cells. For dependable T‑slot machining with Teknik Makina quality, contact Metav Werkzeuge for tailored technical advice or to secure the TKC060TM for the production line — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: TKC060TM Manufacturer: Teknik Makina Diameter: 50 mm Shank diameter: 32 mm Shank cutting length: 45 mm Cutting diameter (shank): 31.5 mm Cutting height: 8 mm Number of cutting edges: 6 Overall length: 120 mm Weight: 0.839 kg Indexable insert type: SPMG 06 Compatible insert manufacturer: Taegutec Insert fastening: M2.2x5 Torx screws Torx key required: T7 Suitable for indexable‑insert milling FAQ Which insert type fits this cutter? The TKC060TM accepts SPMG 06 indexable inserts; the pocket is compatible with inserts from Taegutec. What are the key dimensions for mounting? The cutter has a 32 mm shank and a 120 mm overall length; holders and collets should be specified for a 32 mm shaft. How are the inserts secured and serviced? Inserts are fastened with M2.2x5 Torx screws, serviced using a T7 key for straightforward replacement. What cutting geometry does the tool provide? The tool offers a 50 mm cutting diameter, 6 cutting edges, a 45 mm cutting length and an 8 mm cutting height for deep T‑slot profiles. Is balancing recommended for high‑speed use? For high spindle speeds, balancing is recommended; the cutter mass (approx. 0.839 kg) and its length should be considered when setting up the spindle assembly. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust, indexable‑insert system and a rigid 32 mm shank for stable, repeatable T‑slot machining; combine efficiency, precision and straightforward insert changes to keep production running smoothly — order directly via Metav Werkzeuge or consult our specialists for application advice. Teknik Makina T‑slot cutter, 50 mm diameter, SPMG 06 compatible T‑slot cutter for machining T‑shaped slots and profiles in production and tooling environments, designed for quick insert replacement and high rigidity. 50 mm diameter for deep T‑slots Compatible with SPMG 06 inserts 32 mm shank for rigid clamping Consistent slot accuracy for repeatable production The cutter’s geometry and seven cutting edges deliver a balanced material removal rate that supports consistent slot dimensions across batches. With a 50 mm diameter and a cutting height of 6 mm, the tool is configured to maintain slot form while limiting vibration; this reduces rework and shortens downstream finishing. The result is a reliable machining process that helps control tolerances and improves throughput without excessive tool changes. Stable machining through rigid clamping and optimised length A 32 mm shank and overall length of 120 mm provide the stiffness needed for stable milling even under higher cutting forces. The shank‑to‑cutting length ratio, together with a 31.5 mm cutting shank diameter, lowers deflection and improves surface quality, which is especially important when T‑slots must mate precisely with bolts or sliding fixtures. The cutter’s mass (0.833 kg) contributes to damping, producing a cleaner finish and reducing the chance of chatter on standard CNC milling setups. Fast insert changes and serviceable design This cutter uses SPMG 06 indexable inserts, compatible with inserts from Taegutec, enabling quick index changes and flexible edge selection for different materials and finishes. Insert retention is secured with a M2.2x5 Torx screw and a T7 key specification, allowing service staff to replace or rotate inserts with common workshop tools. The indexable system reduces consumable costs and downtime compared with brazed solutions, making it a practical choice for busy job shops. Application fit and operational benefits Designed within the cutting tools and CNC domain, this milling tool suits fixture and machine‑table T‑slot creation as well as component profiling where a T‑shaped groove is required. Compatibility with industry‑standard insert formats simplifies procurement and inventory, while the tool’s balanced design supports higher material removal rates without sacrificing precision. Choose this cutter when stability and quick serviceability are priorities in repetitive or batch production. For dependable T‑slot machining with Teknik Makina quality, contact Metav Werkzeuge in Emmerich for ordering and tailored technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: TKC054TM Manufacturer: Teknik Makina ECLASS: 21180605 ETIM: EC011860 Weight: 0.833 kg Facts Diameter: 50 mm Overall length: 120 mm Cutting edges: 7 Cutting height: 6 mm Shank diameter: 32 mm Shank cutting length: 45 mm Shank cutting diameter: 31.5 mm Special features Indexable insert system SPMG 06 Compatible with Taegutec inserts Torx screw M2.2x5 for insert fastening Torx key size T7 Designed for T‑slot machining FAQ What insert type does the cutter use? The cutter uses SPMG 06 indexable inserts; Taegutec inserts are listed as compatible for this tool (SKU TKC054TM). How does the shank diameter affect performance? A 32 mm shank increases rigidity during milling, which improves surface finish and reduces deflection when machining T‑slots with this cutter. How many cutting edges are on the tool and what is the benefit? The tool has seven cutting edges; this configuration supports balanced cutting action and helps maintain slot geometry across production runs. Is the tool suitable for quick insert replacement in a shop environment? Yes — insert retention is via an M2.2x5 Torx screw requiring a T7 key, enabling fast service and minimal downtime. What is the overall length and how does it influence setup? The overall length is 120 mm, a dimension that balances accessibility and stiffness for most CNC milling set‑ups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Efficient T-slot milling is achieved with the combination of a 50 mm cutting diameter and four cutting edges, delivering stable material removal and consistent groove geometry; the shaft Ø 32 mm ensures rigid clamping for repeatable results. Order the cutter directly via Metav Werkzeuge or consult our specialists for application support. T-Nut Cutter TKC108TM – Indexable T-slot milling cutter, Ø 50 mm, Teknik Makina The T-Nut Cutter TKC108TM provides precise T-slot machining with indexable CCMT 1204 inserts, designed for workshop and production milling tasks Ø 50 mm cutting diameter Compatible with CCMT 1204 inserts Shaft Ø 32 mm for rigid clamping Four cutting edges for balanced cutting Increase throughput with reliable cutting geometry The large Ø50 mm cutter body combined with four cutting edges permits steady chip removal and reduced vibration, which translates into shorter cycle times and improved surface quality on the machined slot. With support for indexable inserts the tool enables rapid insert changes, lowering downtime compared with brazed or monolithic cutters. The modular concept of insert-based cutters means maintenance is limited to replacing worn CCMT 1204 inserts and the securing screw, keeping production flowing while maintaining dimensional consistency across batches. Fast set-up and secure clamping for repeatable results A robust shaft Ø 32 mm provides secure clamping in standard toolholders, increasing torsional stability during high-feed operations. The cutter’s 110 mm overall length gives adequate reach for common T-slot depths without excessive overhang, while a cutting length of 50 mm offers sufficient engagement for profiling wider slots. Insert retention is handled by an M5x12 Torx screw, tightened with a T20 key, ensuring simple and reliable assembly. These design choices reduce set-up time and help achieve the same tool datum from one shift to the next. Durable construction aimed at consistent production quality The TKC108TM’s balance between body mass and cutting geometry supports consistent machining forces; the tool mass of 0.691 kg contributes to steady cutting dynamics and lowers chatter risk in many milling set-ups. The tool’s compatibility with widely available CCMT 1204 indexable inserts offers a cost-effective route to maintain sharp cutting edges: wear can be addressed by rotating or replacing individual inserts rather than changing the entire cutter. The combination of balanced cutting and replaceable inserts reduces scrap rates and supports a predictable production schedule. Practical workshop guidance and application notes For reliable results, verify holder compatibility with the shaft Ø 32 mm and ensure correct torque on the M5x12 Torx screw using a T20 key to secure each insert. Regular inspection of insert seating and the screw thread will prevent unplanned stoppages. For varied materials, select the appropriate CCMT grade to match hardness and cutting conditions; the indexable system makes grade swaps straightforward. If uncertainty remains about suitability for a specific task, technical advice is available through Metav Werkzeuge to assist with tool selection and process parameters. For precise and dependable T-slot production request the Teknik Makina TKC108TM through Metav Werkzeuge or contact our consultants at Metav Werkzeuge for tailored machining advice Technical Data Article number: TKC108TM Manufacturer: Teknik Makina Designation: T-Nut Cutter Compatible inserts: CCMT 1204 Torx screw: M5x12 Torx key: T20 Key Facts Cutting diameter: 50 mm Number of cutting edges: 4 Shaft diameter: 32 mm Cutting length: 50 mm Cutting height: 20 mm Overall length: 110 mm Weight: 0.691 kg Special features Indexable insert system Balanced four-edge geometry Secure insert fixation with Torx screw Designed for repeatable T-slot machining FAQ Which inserts fit this cutter? The cutter accepts CCMT 1204 indexable inserts; the TKC108TM is configured for these standard carbide inserts to allow rapid replacement and varied cutting grades. What shaft diameter does the tool require for clamping? Clamping requires a holder compatible with a shaft Ø 32 mm, matching the cutter’s shaft for rigid and stable mounting. How many cutting edges are provided and what is the benefit? The tool has four cutting edges, providing balanced cutting forces and steady chip evacuation for consistent slot geometry. What is the overall length and typical reach for the cutter? Overall length is 110 mm, offering sufficient reach for common T-slot profiles while keeping overhang modest for stability. Are special tools required to change the inserts? Insert retention uses an M5x12 Torx screw secured with a T20 key; this standardised solution streamlines insert changes and reduces toolroom complexity. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of 50 mm diameter, secure M16 threaded mounting and compatibility with MGMN 200 indexable inserts for reliable T‑slot production; order the tool directly via Metav Werkzeuge or contact our consultants for application advice. T-slot cutter TKC280TM – 50 mm diameter, for MGMN 200 indexable inserts (Teknik Makina) The T-slot cutter TKC280TM is a purpose-made milling tool for producing precise T‑slots and internal profiles using MGMN 200 indexable inserts, designed for industrial workshop and production use. 50 mm nominal diameter Compatible with MGMN 200 inserts (Korloy) M16 threaded mounting 25 mm shank, two cutting edges Consistent T‑slot geometry for efficient production The TKC280TM is engineered to deliver repeatable groove profiles by combining a 50 mm diameter body with two cutting edges and a 2 mm cutting height, enabling stable material removal and reduced vibration. Using standard MGMN 200 indexable inserts simplifies tool management and lowers downtime: worn inserts are replaced quickly, restoring cutting performance without recalibration. For manufacturing environments where cycle time and predictability matter, this cutter supports steady throughput while preserving the accuracy of each milled T‑slot. Secure mounting and straightforward insert handling A robust M16 thread and a 25 mm shank provide solid clamping and concentricity for the spindle interface, which reduces run‑out and improves surface finish. The tool is supplied with an Allen 6 key for insert clamping, allowing fast, tool‑side changes on the shop floor. Clear mechanical fixation and the use of indexable insert technology mean maintenance is straightforward: insert rotation or replacement restores cutting geometry quickly, supporting lean workflows in small‑batch and serial production alike. Versatility, lightweight design and practical workshop benefits With an overall length of 65 mm and a mass of just 0.152 kg, the cutter balances rigidity with manageable handling during tool changes and storage. Compatibility with common Korloy MGMN 200 inserts makes the cutter a practical choice for workshops that prefer established insert systems; the indexable approach keeps inventory flexible and reduces tooling costs over time. The compact profile of this milling cutter also aids in collision tolerance and toolpath planning on compact machining centres, supporting both retrofit and new‑build setups where space and tool accessibility are considerations. Contact Metav Werkzeuge for procurement and application support with the Teknik Makina TKC280TM—our specialists in Emmerich will advise on suitability and delivery to your workshop. Technical data Article number: TKC280TM Manufacturer: Teknik Makina Product: T‑slot cutter for MGMN 200 indexable inserts Core data Diameter: 50 mm Overall length: 65 mm Shank diameter: 25 mm Weight: 0.152 kg Cutting edges: 2 Cutting height: 2 mm Thread: M16 Allen key: 6 Features / Compatibility Compatible with Korloy MGMN 200 inserts Indexable insert system Threaded mounting for secure clamping Compact overall length for confined setups FAQ Is this cutter compatible with Korloy MGMN 200 inserts? Yes. The TKC280TM T‑slot cutter from Teknik Makina is designed for MGMN 200 indexable inserts and is compatible with Korloy‑brand inserts. What mounting interface does the tool use? The cutter uses an M16 threaded mounting and a 25 mm shank for secure clamping in toolholders and spindle adaptors. How many cutting edges does the cutter have and what is the cutting height? The tool features two cutting edges with a cutting height of 2 mm, providing a balance between material removal and finish quality. Which Allen key is required for insert clamping? Insert clamping and adjustment are carried out with a 6 Allen key supplied for the TKC280TM. What are the dimensions and weight of the tool? The tool has a 50 mm diameter, 65 mm overall length and weighs 0.152 kg. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of reliable indexable‑insert compatibility and a robust 50 mm cutting diameter for consistent thread quality and reduced setup time. Order the cutter directly via Metav Werkzeuge or consult our specialists for application advice. Thread milling cutter for S14, S21, S30 and S40 indexable inserts — Teknik Makina, Ø 50 mm, 153 mm overall length The Thread milling cutter is a heavy‑duty tool for machining threads with indexable‑insert systems, designed for CNC and workshop use with standard Torx clamping. Compatible with S14–S40 indexable inserts Ø 50 mm cutting diameter 153 mm overall length Secured by M5x18 Torx screw (T20) Reliable indexable‑insert system for consistent thread form The tool is built around an indexable insert concept that reduces downtime and simplifies inventory management while maintaining repeatable thread geometry. With a Ø 50 mm cutting diameter and a shank Ø 40 mm, the design supports stable spindle engagement and good chip control in interrupted cuts. Insert changeover is straightforward thanks to the standardised clamping arrangement, so process reliability is increased and toolholder life is preserved. Faster cycles and secure clamping to boost throughput Designed to contribute to faster cycle times, the cutter minimises non‑cutting time by enabling rapid insert replacement and reliable seat repeatability. The head is fixed using an M5x18 Torx screw together with a T20 Torx key, ensuring a firm, repeatable clamp force and reduced re‑setting. This mechanical security lowers the risk of micro‑movement during threading operations, which supports higher feed rates and stable chip evacuation without compromising thread accuracy. Practical integration for professional workshops and CNC cells Engineered for straightforward integration into existing tool systems, the cutter features a 153 mm overall length and a 40 mm toolholder diameter that suit a wide range of toolholders and adaptors. The configuration makes it suitable for shops that favour modular tooling and quick changeovers. Specification and compatibility with S14, S21, S30 and S40 insert formats allow purchasing teams to consolidate insert types across multiple tool families, simplifying logistics and reducing stock complexity. For application advice on the Teknik Makina thread milling cutter (SKU DC217TM) or to request a technical sheet, contact Metav Werkzeuge for tailored recommendations and compatibility checks — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: DC217TM Name: Gewindeschneidfräser / Thread milling cutter Brand: Teknik Makina Compatibility: for S14, S21, S30 and S40 Indexable Inserts Core measurements Cutting diameter: 50 mm Overall length: 153 mm Shank diameter (aufnahme): 40 mm Torx screw: M5x18 Torx key: T20 eCl@ss: 21180805 ETIM: EC011860 Special features Compatible insert types: S14, S21, S30, S40 Indexable‑insert system Secure Torx clamping SKU: DC217TM FAQ Which insert sizes are supported by this thread milling cutter? The cutter supports S14, S21, S30 and S40 indexable inserts as stated in the technical specification for the Teknik Makina thread milling cutter (SKU DC217TM). What are the main dimensions to check for machine integration? Key dimensions are the Ø 50 mm cutting diameter, 153 mm overall length and the 40 mm shank diameter; these ensure compatibility with common toolholders. How is the insert secured in the cutter head? Inserts are secured by an M5x18 Torx screw; tightening and loosening is carried out with a T20 Torx key for reproducible clamp force. Is this cutter suitable for automated tool change systems? The design and standard shank diameter support use in CNC toolholders and many automated systems, provided the toolholder accepts a 40 mm shank and the machine spindle clearance accommodates the 153 mm overall length. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid, ISO‑specified boring solution that accepts WNMG 0804 inserts and delivers consistent chip control via internal coolant; the combination of secure clamping, a 40 mm shank and a 300 mm overall length supports stable, repeatable turning operations—order directly through Metav Werkzeuge or request tailored advice from our consultants. PWLN for WNMG Indexable Inserts (A40T PWLNR) — Right‑hand boring bar, 40 mm shank A PWLN for WNMG Indexable Inserts boring bar engineered for precision internal and external turning applications, compatible with WNMG 0804 inserts and designed for coolant‑through machining Right‑hand cutting direction for standard turning 40 mm shank for high rigidity Internal coolant for improved chip evacuation Compatible with WNMG 0804 indexable inserts Greater rigidity for reliable surface quality The solid design with a 40 mm shank and a sturdy body diameter of 50 mm ensures high rigidity during cutting, reducing vibration and improving dimensional consistency. The tool geometry, including a 95° cutting angle and 60 mm cutting height, is suited to finishing and medium‑duty turning where surface finish and tolerance adherence matter. High rigidity translates directly into fewer reworks and more predictable cycle times, which benefits production planning and process stability. Controlled coolant flow for longer insert life Equipped with internal coolant, the boring bar delivers coolant directly to the cutting zone, supporting effective chip removal and thermal control. This targeted fluid delivery reduces the risk of built‑up edge and thermal softening of the insert, thereby extending insert life and maintaining a consistent surface finish. For operations that require uninterrupted throughput, the coolant‑through capability provides operational reliability and helps to minimise downtime for insert changes. Easy integration and secure clamping for fast set‑up The tool meets the A40T PWLNR ISO designation and accepts WNMG 0804 inserts, enabling compatibility with common indexable insert inventories. The bar’s clamping designation 08 and a total length of 300 mm allow straightforward mounting in standard holders and routers, reducing set‑up time. The right‑hand orientation supports conventional turning cycles. Taken together, these design choices simplify tool management and support consistent process repeatability on the shop floor. Request a tailored quotation or technical consultation via Metav Werkzeuge for Teknik Cutting Tools’ PWLN boring solution — contact info@metav-werkzeuge.com or call +49 2822 7131930 for fast, local supply and advice Technical data Article number: AP364TM ISO designation: A40T PWLNR Product name: PWLN for WNMG Indexable Inserts Numbers / Core technical data Shank diameter: 40 mm Cutting height: 60 mm Weight: 2.8 kg Cutting angle: 95° Body diameter: 50 mm Overall length: 300 mm Design / Special features Compatible inserts: WNMG 0804 Cutting direction: Right Internal coolant: Yes Clamping designation: 08 Manufacturer item name: Bohrstange PWLN für WNMG Wendeplatten FAQ Which inserts are compatible with this boring bar? The boring bar accepts WNMG 0804 indexable inserts; this compatibility ensures quick insert changes and alignment with common shop inventories. Does the tool support coolant‑through machining? Yes, the tool features internal coolant, enabling direct coolant delivery to the cutting edge for better chip control and prolonged insert life. What shank diameter and length does the bar have? The bar is supplied with a 40 mm shank and an overall length of 300 mm, offering a balance of reach and rigidity for a wide range of turning tasks. Is the cutter right‑handed or left‑handed? This tool is configured for right‑hand cutting, suitable for standard turning operations and compatible setups. What is the ISO designation and clamping reference? The bar carries the A40T PWLNR ISO designation and a clamping designation of 08, supporting secure mounting and standardised toolholder fitment. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of secure Torx clamping, a compact 22 mm shank and a 90° cutting geometry for reliable square-shoulder turning; order the tool directly via Metav Werkzeuge or contact their specialists for procurement and technical advice. Eckmesserkopf T215TM — Turning head for ADMT 1204 indexable inserts with 90° cutting angle The Eckmesserkopf T215TM is a compact turning head designed for external square-shoulder and face-turning operations, compatible with ADMT 1204 indexable inserts and built for stable lathe integration. 90° cutting angle for square-shoulder turning 22 mm shank diameter for standard tool posts Compatible with ADMT 1204 indexable inserts Torx fastening M3x7, requires T8 key Improved machining stability for precise shoulder finishes The 90° cutting geometry delivers consistent shoulder formation and planing results while the 50 mm head diameter increases the contact area with the tool post, providing improved rigidity and vibration damping. This stability reduces chatter and helps maintain surface quality during interrupted cuts. Thanks to the 22 mm shank, the holder integrates with many common tool posts without the need for adaptors, enabling a compact, repeatable setup that supports predictable cycle times and consistent component tolerances. Fast, secure insert changes that save setup time Clamping is executed with a Torx M3x7 screw tightened using a T8 key, ensuring a secure and reproducible fit for each insert. The holder is prepared for indexable inserts of the ADMT 1204 format and accepts inserts from Walter, which simplifies procurement and compatibility in mixed-tool shops. With five cutting edges, the insert life is optimised through quick indexing; changeovers take only moments, reducing machine downtime and improving overall tool utilisation. Compact dimensions for tight tool stations and versatile integration With an overall length of 45 mm and a mass of 0.35 kg, the turning head is engineered for operations with restricted overhang and limited turret clearance. The compact footprint supports setups where space is at a premium while the moderate weight keeps centrifugal and dynamic loads low during higher-speed turning. This combination of compactness and performance makes the component suitable for both serial production and small-batch precision work where tool access and repeatability matter. Contact Metav Werkzeuge for stock and tailored application advice regarding the Teknik Makina Eckmesserkopf T215TM; technical enquiries by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: T215TM Manufacturer: Teknik Makina Type: Eckmesserkopf for ADMT 1204 Indexable Inserts Facts Shank diameter: 22 mm Head diameter: 50 mm Overall length: 45 mm Weight: 0.35 kg Cutting angle: 90° Cutting edges: 5 Special features Torx screw: M3x7 Torx key: T8 Compatible insert manufacturer: Walter Suitable for: ADMT 1204 indexable inserts FAQ Is this turning head compatible with ADMT 1204 inserts? Yes. The T215TM is designed specifically for ADMT 1204 indexable inserts and is compatible with inserts from Walter. What mounting and overall dimensions does the holder have? The holder features a 22 mm shank diameter, a 50 mm head diameter and a 45 mm overall length, which makes it suitable for compact tool stations. How are inserts secured in the holder? Inserts are clamped with a Torx screw M3x7; tightening and removal require a T8 key for reproducible clamping torque. What cutting geometry and applications are intended? The tool provides a 90° cutting angle optimized for square-shoulder turning and face finishes, offering stable results on interrupted and continuous cuts. Is the holder suitable for limited-clearance turrets? Yes; the 45 mm overall length and 0.35 kg weight make the T215TM appropriate for tight turret pockets and space-constrained setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Robust machining performance combined with quick insert changes and a stable 32 mm shank ensure consistent T‑slot quality and low downtime. Order the T‑slot milling cutter TKC066TM directly via Metav Werkzeuge or ask our consultants if needed. T-slot milling cutter TKC066TM — 50 mm diameter, six cutting edges (Teknik Makina) A T-slot milling cutter engineered for precision T‑grooves in industrial milling applications, compatible with Taegutec SPMG 07 indexable inserts 50 mm cutting diameter for robust T‑slots 32 mm shank for stable clamping Six cutting edges for efficient material removal Compatible with Taegutec SPMG 07 indexable inserts Accurate T‑slot production with repeatable geometry The T‑slot milling cutter TKC066TM is configured to deliver repeatable slot dimensions thanks to a 50 mm cutting diameter combined with six cutting edges. The multi‑edge arrangement balances chip load and reduces vibration, which leads to improved surface consistency and fewer rework cycles. For production environments where repeatability matters, the cutter’s geometry supports stable finish quality without complex process adjustments. Stable clamping and reduced run‑out for better tool life A 32 mm shank paired with a 120 mm overall length provides a stiff interface between tool and spindle, lowering radial run‑out and improving tool life. The relatively modest mass (0.496 kg) contributes to reduced spindle stress during long runs. These mechanical advantages translate into fewer tool changes and a more predictable maintenance schedule, supporting higher machine uptime and better throughput. Fast insert changes and compatible tooling system Insert changes are straightforward: the cutter accepts SPMG 07 indexable inserts from Taegutec, secured with a M2.5×7 Torx screw that requires a T8 key. This common fastener format simplifies stocking of service parts and shortens changeover time, making the cutter a cost‑effective choice for batch production where quick recovery between jobs matters. Designed for productivity in workshop and production settings With an effective cutting height of 10 mm and an overall design focused on stability, the cutter is suited to repetitive T‑slot machining tasks on industrial milling centres and machining stations. The use of indexable inserts keeps per‑cutting‑edge costs low and allows optimised tool life management by rotating or replacing worn inserts rather than discarding the entire body. Practical selection and setup guidance When integrating the cutter, ensure the machine spindle and clamping system match the 32 mm shank and that sufficient torque is available for the insert screws. The cutter’s compatibility with Taegutec SPMG 07 inserts offers a clear supply path for replacements. For tailored advice on machining parameters or to confirm fitment with specific machines, Metav’s technical team can provide guidance based on production goals and material handling. Contact Metav Werkzeuge for expert advice on supply and optimal setup of the Teknik Makina TKC066TM T‑slot milling cutter — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: TKC066TM Manufacturer: Teknik Makina Name: T‑slot milling cutter Measurements & weights Diameter: 50 mm Shank diameter: 32 mm Cutting shank diameter: 31.5 mm Shaft cutting length: 45 mm Cutting height: 10 mm Number of cutting edges: 6 Overall length: 120 mm Weight: 0.496 kg Features & compatibility Compatible insert: SPMG 07 Compatible insert manufacturer: Taegutec Torx screw: M2.5×7 Torx key size: T8 Story trigger: t-nut-fraeser FAQ Which inserts fit this cutter? The TKC066TM is designed for SPMG 07 indexable inserts; Taegutec recommends these inserts for a reliable fit and repeatable cutting performance. What shank size is required for mounting? Mounting requires a 32 mm shank holder to ensure stable clamping and minimise run‑out when using the TKC066TM. How many cutting edges does the cutter have and what diameter is it? The cutter features six cutting edges and a 50 mm cutting diameter, offering balanced chip removal and good surface quality. How are the inserts secured and what tool is needed? Inserts are secured with an M2.5×7 Torx screw; a T8 key is used for fastening and insert replacement on the TKC066TM. Is the tool body replaced when inserts wear? No — worn insert edges are rotated or replaced individually, which reduces operating costs compared with solid‑tool systems. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of robust insert compatibility, a generous cutting length and a stable shank for dependable holemaking in production runs. Order the Indexable drill U203TM through Metav Werkzeuge or contact our advisers for application-specific guidance. Indexable drill U203TM – Ø 51 mm, 153 mm cutting length (Teknik Makina) The Indexable drill U203TM is a precision insert drill designed for demanding CNC holemaking where repeatability and rapid insert changes are required Diameter 51 mm for deep holes 153 mm cutting length for long bores 40 mm shank for stable clamping Compatible with Korloy WCM-0804 inserts Designed for uninterrupted production with insert-based economy The robust design of this indexable drill targets machine shops and production lines that require consistent throughput without frequent tool regrinds. With a 51 mm diameter and a 153 mm cutting length, the tool reduces the number of refits needed for longer bores, while the substantial 40 mm shank ensures secure clamping and lower vibration. Using an insert system means cutting edges are replaced quickly rather than the entire tool being renewed, which translates into less downtime and a lower cost per hole over high volumes. Precision that supports faster cycle times on CNC equipment Built to integrate with standard machining spindles, the U203TM’s overall length of 268 mm offers reach for deeper operations while keeping rigidity. Compatibility with Korloy WCM-0804 inserts provides a clear maintenance path: worn cutting edges are swapped in seconds, preserving bore quality and surface finish. For shops unfamiliar with insert terminology, an insert is a replaceable carbide cutting piece; using them lets operators maintain stable cutting geometry and consistent part tolerances without specialist grinding skills. Ready for workshop logistics and consistent supply Marked under SKU U203TM, this tool comes as a single, ready-to-fit item with a mass of 2.537 kg, simplifying handling, storage and inventory rotation. The insert-based approach reduces the variety of full tools required in a storeroom since one body can serve many edge changes. Bought via Metav Werkzeuge, customers also benefit from centralised procurement and steady stock levels from Emmerich, which supports reliable delivery into European workshops and minimises supply disruption. For a precise assessment of how the U203TM will perform in specific machining scenarios, contact Metav Werkzeuge for tailored advice and to discuss compatible inserts and delivery options via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: U203TM Manufacturer: Teknik Makina Diameter: 51 mm Overall length: 268 mm Cutting length: 153 mm Shank diameter: 40 mm Shank length: 68 mm Weight: 2.537 kg Suitable insert: WCM-0804 Compatible insert manufacturer: Korloy Facts Ø 51 mm Overall length 268 mm Cutting length 153 mm Shank length 68 mm Shank Ø 40 mm Weight 2.537 kg Special features Compatible with Korloy WCM-0804 inserts SKU U203TM Manufacturer Teknik Makina FAQ Which inserts fit this drill best? The U203TM indexable drill is designed for Korloy WCM-0804 inserts; using the specified insert type maintains intended cutting geometry and tool balance. Can the U203TM be used on standard milling spindles? Yes. The tool’s 40 mm shank and 268 mm overall length allow mounting in typical CNC spindles and drilling heads that accept that shank diameter. How does insert replacement affect uptime? Replacing worn inserts on the U203TM is quick and eliminates the need for regrinding the whole tool body, which reduces machine downtime and keeps production moving. Is the drill suitable for long-reach holes? With a 153 mm cutting length and 268 mm overall length, the U203TM supports deeper bores while preserving rigidity for accurate holemaking. What is the SKU for ordering spare parts or replacements? Order or reference the tool using SKU U203TM when requesting the drill body or compatible insert sets. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Taking advantage of the combination of compact design, integrated internal coolant and precise 90° geometry, the tool head ensures stable corner turning and reduced cycle times; order the component directly via Metav Werkzeuge or request specialist advice from our consultants. Corner tool head T966-3TM — 52 mm diameter, internal coolant (Teknik Makina) The Corner tool head T966-3TM is a compact indexable holder for BOMT 1304 indexable inserts, designed for precise 90° corner turning in confined setups while providing integrated internal coolant to improve tool life and chip control 52 mm diameter for compact turning heads Integrated internal coolant supply Compatible with BOMT 1304 indexable inserts Deliverable precision for corner turning operations The compact head offers a defined 90° cutting angle and placement for BOMT 1304 inserts, delivering repeatable positioning that translates into consistent batch quality. With a 52 mm diameter and a short overall length, the design limits overhang and vibration, which directly benefits surface finish and tolerances. The presence of internal coolant channels supports effective cooling and chip evacuation at the cutting edge, reducing thermal wear and helping to maintain tool geometry over extended runs. This results in fewer regrinds and more predictable tool-change intervals, supporting lean production schedules. Reduced downtime through practical fastening and maintenance Changeovers are simplified by standardised fastening: the head uses M3.5x8.5 Torx screws and an accessible Torx T10 interface, enabling straightforward insert clamping and fast maintenance procedures. The compact overall length of 40 mm and light mass of 0.412 kg allow installation in tight toolpost arrangements with minimal impact on balance. These features support rapid set-up and lower fixturing complexity, which translates into higher machine uptime and easier integration into existing turning cells. Maintenance routines are short and predictable, helping planning and stock management for replacement screws and inserts. Proven compatibility and industrial suitability Designed by Teknik Makina and supplied under SKU T966-3TM, the head is matched to inserts from recognised manufacturers and is specified for BOMT 1304 plates; the toolholder accepts standard indexable parts, ensuring broad availability of cutting grades for different materials. The robust layout and coolant provision make the head suitable for production environments where consistent cycle times and reproducible results are required. The compact profile also facilitates use on smaller lathes and machining centres where access is limited, while retaining the stability expected in industrial turning operations. Contact Metav Werkzeuge today to secure the Teknik Makina corner tool head featuring integrated internal coolant and precise 90° geometry — our advisors at Metav Werkzeuge can confirm compatibility, advise on insert grades and ensure reliable supply from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: T966-3TM Manufacturer: Teknik Makina Product type: Corner tool head Facts Diameter: 52 mm Overall length: 40 mm Weight: 0.412 kg Cutting angle: 90° Number of cutting edges: 5 Torx screw: M3.5x8.5 Torx key: T10 Special features Internal coolant For BOMT 1304 indexable inserts Compatible with inserts from Ingersoll FAQ Which inserts fit this corner tool head? The corner tool head is specified for BOMT 1304 indexable inserts and accepts matching plates from standard suppliers such as Ingersoll Does the tool head support through-tool coolant? Yes — the head features internal coolant channels to supply cutting zones and improve wear resistance What fastening hardware is required for insert clamping? Clamping uses M3.5x8.5 Torx screws tightened with a Torx T10 key for secure and repeatable insert retention Is the head suitable for compact lathes and tight setups? The compact overall length of 40 mm and modest weight (0.412 kg) make it suitable for confined setups where reduced overhang is required Who manufactures this tool head and what is the SKU? The head is manufactured by Teknik Makina and supplied under SKU T966-3TM Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high-precision milling solution that combines economical insert use with stable mounting and reliable repeatability; the T486TM face-milling head accepts BLMP 0904 indexable inserts and delivers consistent finishes with its 100° cutting angle — order directly via Metav Werkzeuge or consult the specialists for integration advice. Face-milling head T486TM — for BLMP 0904 indexable inserts, Ø52 mm The face-milling head T486TM is a compact cutter head designed for light to medium face milling and planing operations using BLMP 0904 indexable inserts, suited to standard machining centres and toolholders. For BLMP 0904 indexable inserts Ø52 mm cutter diameter 6 cutting edges for economical use 22 mm arbor bore for secure mounting Torx screw M3.5x8.5, key T10 High-performance cutting with economical insert use The cutter head is engineered for efficient material removal while keeping operating costs low. With 6 cutting edges and compatibility with BLMP 0904 indexable inserts, the design enables multiple index rotations before replacement, reducing tooling expenditure and downtime. The 100° cutting angle promotes a smooth cut and improved surface finish, especially on broad face operations. The insert seat geometry is optimised to ensure repeatable seating and stable chip evacuation, which translates into predictable cycle times and a reduced risk of premature insert wear. Stable mounting and precise alignment for reproducible results Mechanical stability is achieved through a 22 mm arbor bore and a compact overall form factor (Ø52 mm, total length 50 mm). This configuration provides a rigid connection to the spindle and minimises run-out, allowing tight tolerances to be maintained across production batches. Assembly and clamping are straightforward: fastening is via a M3.5x8.5 Torx screw tightened with a T10 key, enabling reliable clamp forces without complex tooling. The head’s modest mass (0.427 kg) reduces spindle load while preserving cutting stability, which is beneficial for machines with restricted power or for higher-speed finishing operations. Flexible compatibility and practical workshop integration The head is specified for indexable inserts made by recognised manufacturers such as Taegutec, ensuring broad supply availability and interchangeability. Its compact diameter and controlled overhang make it suitable for face milling, light shoulder cuts and finishing passes where accessibility matters. The modular nature of the insert system simplifies inventory: by stocking BLMP 0904 inserts, a workshop can service multiple cutter heads and adapt to varying materials and cutting tasks. Technical terms: an indexable insert is a replaceable carbide cutting element; indexable systems allow rotation to a fresh edge rather than full regrinding, which reduces cost per edge and simplifies tool maintenance. Discuss application requirements with Metav Werkzeuge for optimal setup of the T486TM face-milling head and secure compatibility checks or delivery from Emmerich — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: T486TM Article name: Face-milling head (Planmesserkopf) Manufacturer: Teknik Makina Facts Diameter: 52 mm Bore (arbor): 22 mm Total length: 50 mm Weight: 0.427 kg Cutting angle: 100° Cutting edges: 6 Special features For BLMP 0904 indexable inserts Compatible with Taegutec inserts Torx screw: M3.5x8.5 Torx key size: T10 FAQ What inserts fit this milling head? The face-milling head T486TM is designed for BLMP 0904 indexable inserts and is compatible with inserts from manufacturers such as Taegutec. How is the head mounted to the spindle or arbor? A 22 mm arbor bore is provided for secure mounting; the head is fastened with a M3.5x8.5 Torx screw using a T10 key to ensure stable clamping. What size and type of work is this head best suited to? The head’s Ø52 mm diameter and 100° cutting angle make it appropriate for face milling, light planing and finishing passes on general workshop materials. How many cutting edges are available per head configuration? The T486TM configuration provides 6 cutting edges via the indexable insert system, allowing economical edge rotation before replacement. Is the component weight relevant for spindle selection? The head weighs 0.427 kg, which helps keep spindle load moderate and is suitable for machines with limited power while maintaining cutting stability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact milling solution that combines precise indexable insert compatibility with robust mechanical fixing for consistent chip control and long tool life; ideal for medium-duty milling tasks in production and repair shops. Order the tool directly via Metav Werkzeuge or consult the technical advisers for application-specific recommendations. Round Insert Cutter T667TM — for RDMT 12T3 indexable inserts, Ø52 mm The Round Insert Cutter T667TM is a rotary milling head designed for stable face and light shoulder milling using RDMT 12T3 indexable inserts, suited to general metalworking and toolroom applications. Ø52 mm cutting diameter For RDMT 12T3 indexable inserts Five cutting edges for steady material removal 22 mm shank diameter, compact 0.403 kg weight High material removal with controlled stability The mill head is engineered to deliver efficient machining while keeping vibration in check. The Ø52 mm diameter together with the five cutting edges allows for relatively high feed per tooth without sacrificing surface quality, which contributes to a reliable cycle time. For shops replacing brazed cutters, the use of RDMT 12T3 round inserts provides repeatable cutting geometry and predictable wear behaviour, simplifying process control and reducing downtime. Robust clamping and service-friendly screw system Secure insert retention is achieved with standardised fastening components specified in the data. The cutter uses M4x10 Torx screws and a T15 key for repeatable tightening torque, while the locking screw is M3.5, enabling safe clamping of the inserts under typical milling loads. These familiar fasteners make insert changes straightforward for trained staff and reduce the risk of incorrect torque compared with non-Torx systems, thereby supporting consistent machining results. Compact interface for common toolholders The tool is supplied with a 22 mm toolholder interface and a compact overall length of 50 mm, which helps maintain rigidity in short-overhang setups and improves accessibility in confined fixtures. Its mass of 0.403 kg keeps the spindle load modest, allowing quick acceleration and steady rotation in many bench and CNC machines. The compact dimensions are an advantage in demanding fixture layouts where clearance and stiffness are decisive. Compatibility and practical workshop benefits Designed for use with Palbit-manufactured inserts and identified as compatible with RDMT 12T3, the cutter supports a wide range of grades and chipbreaker geometries available on the market. This flexibility aids process optimisation across steels and non-ferrous materials when appropriate insert grades are selected. The combination of standardised screws and commonly stocked insert formats reduces the need for special inventory, streamlining supply management in the workshop. For tailored technical advice or to secure the Teknik Cutting Tools round insert cutter T667TM with RDMT 12T3 compatibility, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: T667TM Manufacturer: Teknik Makina Product name: Rundplattenfräser Designation (EN): for RDMT 12T3 Indexable Inserts eCl@ss: 21180902 ETIM: EC011860 Facts Diameter: 52 mm Number of cutting edges: 5 Overall length: 50 mm Shank diameter (D): 22 mm Weight: 0.403 kg Special features Compatible with Palbit inserts Fastening screw: M3,5 Torx screw: M4x10 Torx key size: T15 For RDMT 12T3 indexable inserts FAQ Which insert type fits this cutter? The cutter is designed for RDMT 12T3 indexable inserts; compatible grades from Palbit and other manufacturers can be used provided the insert format matches. What fastening hardware is required for insert changes? Insert retention uses an M3.5 locking screw together with M4x10 Torx screws tightened with a T15 key for secure and repeatable clamping. Is the tool suitable for compact fixture set-ups? Yes, the compact 50 mm overall length and 22 mm shank diameter make the cutter suitable for short-overhang arrangements where stiffness and clearance are essential. Can the cutter be used for abrasive or hard alloys? Material suitability depends on the chosen insert grade; the cutter accepts RDMT 12T3 inserts, so selecting an appropriate grade for hardened or abrasive materials is recommended. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact tooling solution that combines a 52 mm diameter, internal coolant and compatibility with RDMT 1604 indexable inserts for reliable, repeatable milling cycles; order via Metav Werkzeuge or consult the technical team for application advice. Round Insert Milling Head for RDMT 1604 Indexable Inserts – 52 mm, Internal Coolant (Teknik Makina) The Round Insert Milling Head is a compact face‑milling solution designed for CNC and machining centres using RDMT 1604 indexable inserts, offering internal coolant and a short overall length for confined setups. 52 mm diameter for compact tool setups Internal coolant to the cutting edge Compatible with RDMT 1604 indexable inserts Four cutting edges for stable material removal High removal rates from a compact tool The tool’s 52 mm diameter and L50 mm overall length are engineered to provide efficient material removal in space‑restricted fixtures. Using RDMT 1604 indexable inserts allows for rapid index changes and consistent cutting geometry, which reduces non‑productive time and tooling cost per cut. The arrangement of 4 cutting edges yields balanced engagement and smoother load distribution, translating into predictable cycle times on medium‑duty milling operations. For shops seeking to standardise holders and inserts, this head delivers straightforward integration without complex adaptation. Internal coolant for improved tool life and surface quality Coolant delivered through the body directly to the insert seat supports controlled temperatures at the cutting zone; the internal coolant mechanism enhances chip evacuation and reduces built‑up edge formation. For processes where thermal stability affects tolerance or surface finish, this feature helps maintain consistent part quality across shifts. The head uses a secure fastener system with T15 Torx drive and M4x10 screws, ensuring repeatable clamping torque and reliable coolant passage to the insert pockets. Quick serviceability and secure assembly Maintenance routines are simplified by the indexable design and standardised fastening: insert changes use the T15 key and M4x10 screws, reducing downtime during tool service. The tool’s low mass (0.35 kg) eases handling when mounting or balancing multi‑cutter arrangements and contributes to faster changeovers at the machine. Clear access to the screwheads and a conventional clamping concept make insert replacement and inspection efficient for trained operators, lowering the risk of assembly errors. Reliable choice for versatile face‑milling tasks Designed by Teknik Makina as a compact face milling head, this tool supports routine milling where a short overhang and focused coolant supply are advantageous. The compatibility with standard RDMT 1604 indexable inserts allows workshops to choose grades and geometries tailored to their cutting strategy while keeping insert inventory aligned across similar tool families. The combination of compact geometry, coolant delivery and standard fasteners makes this head a pragmatic option for production environments that prioritise repeatability and easy servicing. Discuss the suitability of the Teknik Makina round insert milling head with Metav Werkzeuge’s specialists or place an order via Metav Werkzeuge for delivery from Emmerich – eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical data SKU: T271-1TM Label: 52 mm round insert milling head for RDMT 1604, L50 mm, internal coolant Manufacturer: Teknik Makina Facts Diameter: 52 mm Overall length: 50 mm Weight: 0.35 kg Number of cutting edges: 4 Screw: M4x10 Torx key: T15 Compatible inserts: RDMT 1604 Special features Internal coolant to the insert seat Indexable insert system Face milling head design Manufacturer SKU: T271-1TM FAQ Is this head compatible with RDMT 1604 inserts? Yes. The head is designed specifically for RDMT 1604 indexable inserts and accepts standard insert geometries for that designation. Can the internal coolant be used with standard coolant supply lines? The internal coolant channel is integrated into the head body and is intended to be supplied from the machine’s coolant feed to deliver fluid directly to the insert seat. What fasteners are used to secure the inserts? Inserts are retained using M4x10 screws driven with a T15 Torx key; this provides a reliable clamping interface and repeatable torque handling. Is the tool suitable for confined or short‑overhang set‑ups? Yes. The compact 52 mm diameter and L50 mm overall length make it well suited to operations with limited clearance or reduced overhang requirements. How does the indexable design affect maintenance intervals? Indexable inserts allow worn edges to be rotated or replaced without removing the entire head, reducing downtime and lowering consumable costs compared with solid cutters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise indexable-insert compatibility, compact design and simple insert replacement for shortened downtimes; order the milling cutter directly via Metav Werkzeuge or ask our consultants for technical advice. Rundplattenfräser T271TM — indexable-insert face mill, Ø52 mm, Teknik Makina The Rundplattenfräser T271TM is a compact indexable-insert face mill intended for finishing and light roughing with RDMT 1604 inserts in CNC and manual milling operations Ø52 mm diameter for tight machining 4 cutting edges for smooth finishes 22 mm shank for secure toolholder fit Compact 50 mm overall length for constrained spaces Faster cycle times with consistent surface quality The cutter’s Ø52 mm diameter combined with its 4 cutting edges enables steady material removal and a fine surface finish on interrupted and continuous cuts. Using standard RDMT 1604 indexable inserts reduces dwell time: inserts can be rotated or replaced quickly without regrinding. For production environments this means shorter non-productive intervals and more consistent part geometry, which directly supports predictable cycle times and improved process repeatability. Robust clamping and fast insert changes reduce downtime A 22 mm tool shank ensures reliable seating in common toolholders, supporting stable machining even at higher feed rates. The tool secures inserts with a M4x10 locking screw and a M4.5x11 Torx screw (Torx key T20), making insert changes straightforward and reproducible. The clear interface between cutter body and insert pocket minimises the risk of misalignment, which prolongs insert life and reduces the frequency of tool-setting operations. Compact design for versatile machine use With a total length of 50 mm and a mass of 0.35 kg, the milling head is engineered for situations where toolchanger clearance or fixture proximity is limited. The compact envelope allows closer approach to fixturing and simpler toolpath planning, while the relatively low mass contributes to lower spindle load during acceleration. This design suits job-shop environments and CNC cells where flexibility and space efficiency are priorities. Industry compatibility and traceable specification The milling head is specified for the widely used RDMT 1604 insert format, ensuring easy sourcing of consumables and predictable wear behaviour. Relevant classification codes are recorded for procurement systems: eClass 21180902 and ETIM EC011860, which support clear parts management across ERP systems. The cutter’s defined fastening and interface dimensions simplify integration into existing tool inventories and maintenance routines. For procurement or technical clarification on Teknik Makina indexable face mills, contact Metav Werkzeuge for ordering and application support at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T271TM Manufacturer: Teknik Makina Product name: Rundplattenfräser For inserts: RDMT 1604 Indexable Inserts eClass: 21180902 ETIM: EC011860 Facts Diameter: 52 mm Number of cutting edges: 4 Overall length: 50 mm Shank / mounting diameter: 22 mm Weight: 0.35 kg Locking screw: M4x10 Torx screw: M4.5x11 Torx key size: T20 Special features U-plate designation: BSP010 Compatible with RDMT 1604 insert format Compact design for limited tool clearance FAQ Which insert type fits this cutter? The cutter accepts RDMT 1604 indexable inserts; RDMT 1604 inserts provide quick indexing and are widely available for different grades and chipbreakers. What are the key dimensions to check for toolholder compatibility? Check the 22 mm shank diameter and the 50 mm overall length to confirm seating and clearance in the chosen toolholder; the cutter’s Ø52 mm cutting diameter determines the required toolpath offsets. How are the inserts secured and changed? Inserts are secured with a M4x10 locking screw and a M4.5x11 Torx screw; a T20 Torx key is used for tightening and removal to ensure consistent clamping torque. Is this cutter suitable for finishing and roughing? The tooling is intended primarily for finishing and light roughing operations using RDMT 1604 inserts; machining parameters should be adapted to the specific material and insert grade. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precision, secure clamping and internal coolant for stable, high-feed face milling — order directly via Metav Werkzeuge or consult our technical team for application-specific advice. Face milling head for BLMP 0603 indexable inserts — 52 mm diameter, internal coolant (Teknik Makina) A face milling head for BLMP 0603 indexable inserts designed for robust face milling operations where coolant-fed cutting and compact overall length support consistent surface quality. 52 mm cutting diameter Internal coolant supply Compatible with BLMP 0603 inserts Robust design with 7 cutting edges Coolant-controlled cutting for higher process stability The internal coolant channel delivers coolant directly to the cutting zone, reducing cutting temperature and improving chip evacuation. This lowers tool wear and supports longer service intervals, which in turn increases process uptime and reduces total machining cost. Designed for industrial use, the face milling head facilitates consistent heat management during continuous cycles and helps to maintain repeatable results across batches. Compact, rigid construction for consistent surface finish A compact overall length of 50 mm combined with a 52 mm diameter and a mass balanced layout deliver reduced vibration and stable cutting conditions. The arrangement of 7 cutting edges provides multiple indexing positions before replacement, allowing sustained material removal rates and fewer tool changes. The result is improved surface finish and dimensional consistency on series parts, especially where repeatability is essential. Fast insert changes and secure fastening to cut downtime Insert clamping and fastening use standard hardware for quick servicing: Torx T8 key engagement and M3x6.2 Torx screws ensure secure retention and straightforward replacement of the BLMP 0603 indexable inserts. The cutter body is supplied ready for Taegutec-compatible inserts, simplifying procurement and reducing setup complexity. Lightweight yet rigid, the tool body supports efficient handling while maintaining the clamping integrity required for productive machining. For tailored procurement or application advice on Teknik Makina face milling solutions, contact Metav Werkzeuge — Metav’s Emmerich location combines extensive stock and technical expertise to ensure the right tool reaches the workshop quickly; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: T482-1TM Product: Face milling head Model/label: 52 mm face milling head BLMP 0603 L50 mm with internal coolant Manufacturer: Teknik Makina Facts Diameter: 52 mm Overall length: 50 mm Mounting diameter: 22 mm Weight: 0.472 kg Cutting edges: 7 Cutting angle: 100° Special features Internal coolant supply For BLMP 0603 indexable inserts Compatible insert manufacturer: Taegutec Torx key: T8 Torx screw: M3x6.2 eClass: 21181015 UID: T482-1TM FAQ What insert type does this cutter use? The cutter is designed for BLMP 0603 indexable inserts and is compatible with Taegutec-manufactured inserts, enabling straightforward procurement and interchangeability. Is the tool coolant-fed and what benefit does that bring? Yes — the internal coolant channel supplies coolant directly to each cutting edge, which improves chip control, reduces thermal wear and extends the usable life of the inserts. What fastening hardware is required for insert replacement? Insert retention uses a Torx T8 key and M3x6.2 Torx screws for secure clamping and quick servicing of the BLMP 0603 inserts. What are the main dimensions and balance considerations? Key dimensions include a 52 mm cutting diameter and 50 mm overall length; the compact design and balanced construction provide reduced vibration for consistent surface quality. Who manufactures this face milling head and how is it identified? The tool is supplied by Teknik Makina and is listed under SKU T482-1TM for ordering and identification. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a compact 52 mm cutting diameter with internal coolant and secure Torx clamping, this face milling head provides reliable finishing performance for BLMP 0904 indexable inserts; order directly via Metav Werkzeuge or consult our specialists for application advice. Face milling head T486-1TM — 52 mm diameter, internal coolant (Teknik Makina) T486-1TM is a compact face milling head designed for BLMP 0904 indexable inserts, offering a short overall length and coolant-fed cutting for consistent surface quality. 52 mm cutting head diameter Internal coolant for improved chip evacuation Holds BLMP 0904 indexable inserts Compact 50 mm overall length High-performance finishing from a compact cutter body The compact face milling head combines a 52 mm diameter with a 100° cutting angle and six cutting edges, creating a tool geometry optimised for stable contact and consistent finishing. Fit with BLMP 0904 indexable inserts, the cutter body allows predictable load distribution across the inserts, which reduces vibration and supports uniform surface results. The design is aimed at production and job-shop environments where repeatable quality and short setup times are priorities. The included fastening specification ensures secure seating and reliable torque transmission for daily machining cycles. Coolant-fed clamping for longer insert life and cleaner chips Built-in internal coolant channels supply cutting fluid directly to the insert pocket to aid cooling and chip control. This targeted coolant feed helps reduce the risk of built-up edge and supports longer tool life without complex retrofit work. The milling head uses a 22 mm mounting interface for stable spindle connection and employs T10 Torx drive geometry with M3.5x8.5 screws for simple and robust clamping. As a result, insert changes are fast and the cutter maintains alignment under load, helping to preserve tolerances and minimise rework. Compact dimensions and workshop-friendly handling With an overall length of 50 mm and a lightweight construction at approximately 0.427 kg, the cutter is easy to handle and suits tight setups or multi-axis machines where space is limited. The short projection reduces bending moments and supports higher dimensional accuracy at the cutting zone. Maintenance routines remain straightforward thanks to standardised Torx screws and widely available BLMP 0904 inserts from suppliers such as Taegutec, making the tool practical for both small batch work and continuous production runs. The robust, service-oriented design supports dependable performance across varied schedules. Contact Metav Werkzeuge for compatibility checks and tailored application guidance on the Teknik Makina T486-1TM face milling head; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: T486-1TM Manufacturer: Teknik Makina Product type: Face milling head Compatible inserts: BLMP 0904 Compatible insert supplier: Taegutec Facts Cutting head diameter: 52 mm Overall length: 50 mm Weight: 0.427 kg Mounting diameter: 22 mm Number of cutting edges: 6 Cutting angle: 100° Special features Internal coolant: yes Torx key size: T10 Torx screw: M3.5x8.5 ECLASS: 21181015 FAQ Which indexable inserts fit this milling head? The face milling head accepts BLMP 0904 indexable inserts; inserts from Taegutec are specified as compatible with the T486-1TM cutter. Is the cutter supplied with internal coolant? Yes — the cutter body includes internal coolant channels to deliver cutting fluid directly to the insert zone, improving chip evacuation and thermal control. What is the mounting interface for the cutter? The milling head uses a 22 mm mounting diameter for spindle or arbor attachment, providing a compact and stable connection. How many inserts does the head accommodate and what is the cutting angle? The head is configured for six cutting edges and a 100° cutting angle, which supports stable face milling and consistent surface finishes. What fastening hardware is required for insert clamping? Clamping is achieved with T10 Torx drive screws; the specified screw size is M3.5x8.5, enabling secure and service-friendly insert changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, high-performance tool that combines a 52 mm diameter, four cutting edges and a 45° cutting angle to deliver stable face milling with SDMT 1204 inserts; order directly via Metav Werkzeuge or consult our specialists for integration and stocking advice. Face milling head T358-2TM – 52 mm diameter, for SDMT 1204 indexable inserts (Teknik Makina) The Face milling head for SDMT 1204 indexable inserts is a short, robust tool body engineered for dependable face milling and finishing operations in general machining environments 52 mm diameter for broad coverage Compatible with SDMT 1204 inserts Four cutting edges for longer service 45° cutting angle for smooth chip flow Consistent compatibility reduces setup time The milling head is built to accept SDMT 1204 indexable inserts and aligns with common ZCC geometries, which simplifies tool selection and reduces setup complexity. Paying attention to standard insert formats means fewer special orders and faster changeovers on the shop floor. The result is consistent cutting behaviour and predictable process parameters, allowing production planning to rely on repeatable cycle times. Precision and repeatability for reliable finishes A 45° cutting angle combined with four cutting edges gives a balance between cutting stability and surface quality. The geometry minimises vibration and distributes cutting forces evenly across the tool body, which improves component finish and extends insert life. With a 52 mm diameter and compact 40 mm overall length, the design supports controlled engagement for both finishing and light roughing tasks while maintaining a reliable run-out performance. Fast maintenance and secure fastening for minimal downtime Secure clamping is achieved with M4x10 Torx screws tightened with a T15 drive, enabling swift insert swaps and consistent torque application. The straightforward fastening system reduces the risk of incorrectly seated inserts and lowers maintenance time between operations. As a result, the milling head supports higher machine uptime and simpler spare-part handling in maintenance routines. Ready-to-stock design that streamlines procurement The tool body (SKU T358-2TM) is compact and lightweight at approx. 0.381 kg, which simplifies storage and handling and allows efficient stocking across multiple workstations. Sourcing through Metav aligns supply with quality control: orders are fulfilled from Emmerich with an emphasis on verified parts and consistent availability, helping workshops and trade customers reduce supplier fragmentation and secure dependable deliveries. For supply or technical advice on Teknik Makina’s 52 mm face milling head (T358-2TM) contact Metav Werkzeuge in Emmerich for tailored procurement and integration guidance — info@metav-werkzeuge.com, +49 2822 7131930 Technical data SKU: T358-2TM Manufacturer: Teknik Makina Product type: Face milling head Label: 52mm Planmesserkopf SDMT 1204 L40mm Key specifications Diameter: 52 mm Overall length: 40 mm Shank / mounting diameter: 22 mm Weight: 0.381 kg Cutting edges: 4 Cutting angle: 45° Fastening screw: M4x10 Drive: Torx T15 Compatibility & features For SDMT 1204 indexable inserts Compatible with ZCC insert geometries Compact design for stable engagement Torx fastening for repeatable clamping FAQ Which insert type fits this milling head? The milling head accepts SDMT 1204 indexable inserts; compatibility with common ZCC geometries ensures straightforward insert procurement. What is the tool’s diameter and suitable application? The 52 mm diameter and 45° cutting geometry make the head suitable for face milling operations that require stable engagement and good surface finish. How are inserts secured to the tool body? Inserts are clamped using M4x10 Torx screws tightened with a T15 drive, which supports quick and repeatable insert changes. Is the SKU useful for reorders and stock management? Yes — the SKU T358-2TM identifies the compact face milling head for streamlined ordering and inventory control. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Compact, efficient machining with a small footprint: the combination of a 52 mm diameter, a 45° cutting angle and four cutting edges ensures stable face milling and reduced cycle times. Integrated coolant support extends tool life and improves surface finish. Order the face milling head directly via Metav Werkzeuge or ask our consultants if needed. Face milling head for SDMT 1204 indexable inserts — 52 mm, internal coolant (Teknik Makina) Face milling head for SDMT 1204 indexable inserts designed for compact, precise material removal in CNC and turning-milling centres. Face milling head for SDMT 1204 inserts 52 mm diameter for compact operations Internal coolant supply for heat control Compatible with ZCC indexable inserts Faster cycles through compact, powerful cutting The small-diameter milling head combines a 52 mm body with a 45° cutting angle to deliver efficient material removal while reducing spindle load. Fitted for SDMT 1204 indexable inserts and providing 4 cutting edges, this configuration shortens toolpaths and minimises changeover frequency—benefits that translate directly into higher throughput on batch and jobbing work. The geometry supports stable chip evacuation and consistent surface quality on each pass. Cooler cutting for longer tool life and better finishes Built-in internal coolant directs fluid precisely to the insert pocket and cutting zone, lowering temperatures and flushing chips away from the cutting edge. Reduced thermal stress and clearer cutting zones slow wear progression, which results in longer insert life and fewer interruptions for maintenance. For operations that demand repeatable surface condition and tight process windows, the coolant provision is a decisive advantage for sustained productivity. Secure clamping and quick insert handling The cutter head is secured with M4x10 Torx screws tightened using a T15 Torx key, enabling fast, repeatable insert changes and a consistently secure clamp force. Compatibility with ZCC manufactured inserts provides flexibility when choosing grades for ferrous or non-ferrous work, while the modest mass (0.379 kg) and an overall length of 40 mm make handling and toolset balancing easier during setup and tool changes. Compact mounting for versatile machine integration A 22 mm mounting diameter allows installation on compact toolholders and multi-tasking turrets, making this head suitable for small to medium machine tools where space and clearance are limited. The construction supports precise indexing and concentricity, which is advantageous for finishing passes and mixed-material batches. Supplied by Teknik Makina and identified as SKU T358-3TM, the unit is a practical choice for workshops aiming to improve flexibility without compromising process reliability. For precise, compact face milling solutions from Teknik Makina, contact Metav Werkzeuge for ordering details or technical compatibility checks—eMail info@metav-werkzeuge.com or call +49 2822 7131930 to discuss your application and logistics. Technical data SKU: T358-3TM Manufacturer: Teknik Makina Product type: Face milling head Facts Diameter: 52 mm Overall length: 40 mm Weight: 0.379 kg Mounting diameter: 22 mm Cutting angle: 45° Cutting edges: 4 Special features Internal coolant For SDMT 1204 indexable inserts Compatible with ZCC inserts Torx key: T15 Torx screw: M4x10 FAQ Which inserts fit this milling head? The face milling head accepts SDMT 1204 indexable inserts and is compatible with ZCC insert manufacturers; choose the grade appropriate for the workpiece material and machining strategy. Does the head provide coolant to the cutting zone? Yes, the unit features internal coolant that delivers fluid directly to the insert pockets, improving cooling and chip evacuation during cutting. What mounting diameter is required? The milling head uses a 22 mm mounting diameter for attachment to compatible toolholders and turrets. How many cutting edges are active on the head? The head is designed for 4 cutting edges, enabling balanced cutting and efficient material removal per revolution. Which fastening hardware and tool are needed for insert changes? Insert pockets are secured with M4x10 Torx screws tightened using a T15 Torx key for quick and secure insert replacement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, productivity-focused milling solution that combines a 52 mm diameter, internal coolant and compatibility with SDNW 1205 indexable inserts for shorter cycle times and reliable surface finish; order the head directly via Metav Werkzeuge or consult our specialists for application support. Face milling head (Planmesserkopf) for SDNW 1205 — 52 mm, internal coolant — Teknik Makina The face milling head is a compact, internally cooled cutter head designed for light to medium-duty face milling using SDNW 1205 indexable inserts; ideal where space is limited but process stability remains essential. Compatible with SDNW 1205 indexable inserts 52 mm diameter for compact face milling Internal coolant for enhanced chip evacuation Five cutting edges; L50 mm overall length Increased productivity from compact, targeted design The compact diameter and controlled geometry prioritise material removal where it matters. With a 52 mm diameter and five cutting edges, the head shortens non-cutting times while maintaining consistent engagement for face operations. The 90° cutting angle delivers a square shoulder finish and predictable cutting forces, which helps stabilise feed rates and reduce vibration. Specified for SDNW 1205 inserts, the configuration allows the use of proven insert grades from recognised manufacturers, enabling a clear performance comparison and straightforward tool selection. The combination of compact form and defined insert compatibility supports higher spindle speeds or tighter tool spacing where multiple heads are used on the same spindle. Better chip control and process reliability through internal coolant Internal coolant is built into the design to improve chip evacuation and extend insert life in continuous cycles. The internal coolant channel directs coolant close to the cutting edge, aiding lubrication and heat dissipation so that the insert maintains sharper cutting geometry for longer. This reduces the frequency of index changes and contributes to a more predictable tool lifecycle, which in turn simplifies production planning. The head is secured with an M4x10 Torx screw and requires a T15 Torx key, enabling fast, repeatable clamp-up and straightforward maintenance during shift changes. With an overall length of L50 mm and a mass of approximately 0.378 kg, the unit is easy to handle and integrates without significant balance disruption on standard toolholders. Simple installation, dependable serviceability and supply continuity Mounting and service are kept efficient: a single Torx fastener and compatible insert pocket geometry mean quick insert replacement and reduced downtime. The robust construction supports repeated index changes and routine handling in busy workshop environments. Compatibility with inserts from Hitachi ensures access to a wide range of grades for different materials and cutting conditions, while standard fastening hardware limits the need for special tools. For buyers focused on reliable sourcing, Metav Werkzeuge offers steady availability from Emmerich and product support that links practical application knowledge with secure European distribution, helping to streamline procurement and reduce supplier complexity. Contact Metav Werkzeuge for tailored application advice on the Teknik Cutting Tools face milling head T383TM and for current stock information — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: T383TM Product type: Planmesserkopf Brand: Teknik Makina Compatible inserts: SDNW 1205 Inserts manufacturer: Hitachi Facts Diameter: 52 mm Overall length: 50 mm Weight: 0.378 kg Cutting edges: 5 Cutting angle: 90° Special features Internal coolant Torx key: T15 Torx screw: M4x10 SKU: T383TM FAQ Which inserts fit this milling head? The milling head accepts SDNW 1205 indexable inserts; Hitachi insert grades are commonly used with this head for a range of finishes and workpiece materials. Is the head suitable for wet machining? Yes — the head features internal coolant, which guides coolant directly to the cutting zone for improved lubrication and chip control during wet operations. What fastening hardware is required for insert changes? Insert clamping uses an M4x10 Torx screw, tightened with a T15 Torx key for consistent, repeatable securement. Can the head be used for shoulder milling and light facing? The 90° cutting angle and compact form make the head appropriate for square-shoulder milling and light face operations where a compact cutter is beneficial. How does the head help reduce downtime? Quick insert changes, standard Torx fastening and compatibility with widely available SDNW 1205 inserts reduce changeover time and simplify spare-part inventories. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of a compact 52 mm diameter, internal coolant and compatibility with SOET 13 indexable inserts ensures consistent face-milling performance and simple insert changes. Order the planing cutter head directly via Metav Werkzeuge or consult our advisors for application-specific guidance. Planing cutter head for SOET 13 indexable inserts — 52 mm, internal coolant (Teknik Makina) The Planing cutter head is designed for face milling with SOET 13 indexable inserts and is intended for compact, high-precision finishing and semi-roughing operations in small- to medium-sized workshops. 52 mm diameter for compact machining Internal coolant for improved chip evacuation Compatible with SOET 13 Palbit inserts Four cutting edges, 90° cutting angle Consistent results from compact design and insert compatibility The compact 52 mm diameter design provides a stable, space-saving solution for machining faces where tool access is restricted. Compatibility with SOET 13 indexable inserts keeps operating costs predictable: worn edges are replaced rather than the entire tool, maintaining productivity while reducing tooling downtime. Indexable inserts are small, reversible cutting elements that simplify maintenance and inventory control, delivering a fast return to production after a changeover. Longer cutting life and improved surface quality through internal coolant Integrated internal coolant channels direct cutting fluid precisely to the cutting zone, which reduces heat at the cutting edge and improves chip evacuation. The result is extended insert life and a more consistent surface finish under load. For materials prone to built-up edge or thermal sensitivity, internal coolant supports higher stable cutting parameters and helps keep cycle times down without compromising component quality. Secure clamping and reliable fastenings for vibration control A robust fastening system with T15 Torx drive and M3.5×8.5 screws ensures stable clamping of the inserts during interrupted cuts and heavier passes. The combination of four cutting edges and a 90° cutting angle produces uniform loading on each insert, reducing vibration and run-out. This mechanical reliability translates directly into improved dimensional accuracy and repeatability on milled faces. Practical fit for everyday workshop use With an overall length of 45 mm and a mass near 0.401 kg, the head is easy to handle and suits operations seeking a balance between rigidity and manoeuvrability. Compatibility with Palbit-supplied SOET 13 inserts broadens sourcing options while retaining performance standards. The compact face-milling solution is suitable for finish machining and medium-material-removal-rate tasks where quick insert changes and coolant-fed operation are decisive advantages. For tailored technical advice on the Teknik Makina face milling head (SKU T638TM) and to confirm compatibility for specific machines or materials, contact Metav Werkzeuge’s technical team for direct assistance and supply coordination. Technical data SKU: T638TM ECLASS: 21181015 Manufacturer: Teknik Makina Numeric specifications Diameter: 52 mm Overall length: 45 mm Weight: 0.401 kg Cutting edges: 4 Cutting angle: 90° Screw: M3.5×8.5 Torx key: T15 Features / Compatibility Internal coolant For SOET 13 indexable inserts Compatible with Palbit inserts Face milling application Product type: Planing cutter head FAQ Is this head compatible with SOET 13 inserts from other manufacturers? Compatibility is confirmed for SOET 13 geometry; the head accepts inserts from Palbit and other manufacturers producing the same SOET 13 specification, provided insert seating and clamping match the indexable insert geometry. Can the internal coolant be used on all machine types? The internal coolant feature requires a machine-side coolant supply; the planing cutter head supports coolant-fed operation when connected to a suitable internal coolant line on the spindle. What advantages does a 90° cutting angle provide for face milling? A 90° cutting angle delivers a square shoulder and reduces radial forces, improving surface finish and dimensional control on face-milled components with the planing cutter head. How many cutting edges are available before inserts need replacement? The head uses indexable inserts with four usable cutting edges per insert; rotating or replacing inserts restores cutting performance without replacing the entire head assembly. Which Torx key is required for insert changes? Insert fastening uses a T15 Torx drive with M3.5×8.5 screws for reliable clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact face milling solution that pairs a 52 mm cutting diameter with a 100° cutting angle for consistent surface finish; the head accepts BLMP 0603 indexable inserts and secures with an M3x6.5 screw for reliable clamping. Combine precise cutting geometry and quick insert changes for shorter setup times — order the head directly via Metav Werkzeuge or request application advice from our consultants. Face milling cutter head T482TM — for BLMP 0603 indexable inserts, 52 mm diameter (Teknik Makina) The face milling cutter head T482TM is a compact milling head engineered for efficient face operations with BLMP 0603 indexable inserts, suited to production environments that demand repeatable surface quality and fast changeovers. For BLMP 0603 indexable inserts 52 mm cutting diameter 7 cutting edges for extended tool life 22 mm toolholder attachment Precision performance for repeatable face milling The milling head delivers a 52 mm cutting diameter combined with a 100° cutting angle, engineered to produce even chipflow and a stable cutting engagement. This geometry reduces vibration at the cut edge and promotes a consistent surface finish on the workpiece, which means fewer rework operations. With 7 cutting edges on the circumference, the design distributes cutting forces and extends service intervals; the result is improved process uptime and predictable tool-life behaviour in short- and medium-run production. Fast setup and compatibility with standard inserts Designed for quick integration, the tool accepts BLMP 0603 indexable inserts and is compatible with Taegutec inserts that follow the same specification. The shank mates to a 22 mm toolholder, while the insert pocket is secured with an M3x6.5 screw and a Torx T8 drive for repeatable clamping torque and straightforward servicing. These characteristics minimise changeover time and simplify inventory management, as common insert sizes can be stocked across multiple cutter heads to reduce diversity on the shop floor. Built for balance and dependable workshop use At an overall length of 50 mm and a mass of 0.472 kg, the cutter head is compact and sufficiently rigid for stable rotation at typical milling speeds; its dimensions support good dynamic balance when mounted in a standard holder. The compact form factor reduces overhang and helps maintain concentricity, which lowers the risk of chatter and contributes to consistent dimensional accuracy. Together with standardised fastening and insert geometry, the assembly supports predictable machining results and easier process planning. For tailored technical guidance on integrating the Teknik Makina face milling cutter head T482TM into existing tooling systems, contact Metav Werkzeuge for application recommendations at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: T482TM Manufacturer: Teknik Makina Designation: face milling cutter head for BLMP 0603 indexable inserts Facts Diameter: 52 mm Overall length: 50 mm Attachment / shank diameter: 22 mm Weight: 0.472 kg Cutting edges: 7 Cutting angle: 100° Fastening screw: M3x6.5 Special features Compatible with BLMP 0603 indexable inserts Compatible with Taegutec inserts Torx key size: T8 Compact design for reduced overhang FAQ Which insert type does the cutter head accept? The face milling cutter head accepts BLMP 0603 indexable inserts; compatible Taegutec variants are supported by the same pocket geometry. What is the required toolholder diameter for mounting? Mounting requires a 22 mm toolholder attachment; the head's 22 mm interface ensures a secure fit and correct concentricity. How is the insert secured in the cutter head? Inserts are clamped with an M3x6.5 screw using a Torx T8 drive to provide repeatable clamping and straightforward replacement. Is the cutter head suitable for high-speed finishing passes? The combination of a 100° cutting angle and compact geometry supports stable finishing operations; balance and holder selection remain important for high-speed applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com