Gibt es einen Hahn und Kolb Online Shop?

Take advantage of a compact design, precise geometry and secure clamping for reliable internal turning in tight bores; the combination of a 5 mm cutting diameter, 8 mm shank and compatibility with CC-- 0301 indexable inserts keeps machining setups simple and repeatable — order via Metav Werkzeuge or consult our specialists for application advice. K097TM Boring bar — SCLC for CC-- indexable inserts, 5 mm, right-hand (Teknik Makina) K097TM Boring bar presented as a compact SCLC tool for precise internal turning in constrained bores using CC-- 0301 indexable inserts Compact 5 mm boring diameter Shank diameter 8 mm for secure clamping Compatible with CC-- 0301 indexable inserts Right-hand cut with 95° cutting angle Accurate internal turning with compact geometry The K097TM boring bar is engineered for tasks where space is limited but dimensional accuracy remains critical. With a 5 mm nominal cutting diameter and 100 mm overall length, this SCLC toolholder offers a narrow footprint while maintaining the rigidity required for internal turning. The 8 mm shank supports secure clamping in standard holders, reducing vibration and improving surface finish. The ISO designation S05H SCLCR indicates a standardised tool geometry that facilitates repeatable setup and interchangeability across compatible toolposts and holders. Reduced setup time through indexable-insert compatibility Designed specifically for use with CC-- 0301 indexable inserts, the boring bar simplifies insert changes and reduces downtime. The 15 mm cutting height and the holder form factor ensure correct seating of the insert, while the right-hand cutting orientation and 95° cutting angle offer predictable chip flow and stable cutting forces. For manufacturing environments prioritising throughput, the modularity of an indexable system translates into faster maintenance and consistent component quality, making this bar suitable for short-run and medium-run production where quick tool replacement is an advantage. Practical benefits for workshop and production use Beyond raw dimensions, this tool delivers practical benefits: low mass at 0.046 kg eases handling and minimises centrifugal effects in high-speed operations, and the defined holder geometry supports accurate repeatability when changing tools. The compact design enables access to confined bores that conventional tools cannot reach, expanding machining options without necessitating larger setups. When paired with the correct clamp and holder, the bar contributes to reliable machining cycles and predictable part tolerances, aligning with rational efficiency and process stability objectives. Contact Metav Werkzeuge for tailored application guidance on Teknik Cutting Tools products and secure delivery from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: K097TM Type designation: S05H SCLCR Application designation: SCLC for CC-- Indexable Inserts Facts Diameter: 5 mm Shank diameter: 8 mm Cutting height: 15 mm Overall length: 100 mm Weight: 0.046 kg Cutting angle: 95° Cutting direction: Right-hand Materials & compatibility Compatible inserts: CC-- 0301 Clamp holder designation: 03 Suitable for indexable insert systems (SCLC form) FAQ Which insert type fits this boring bar? The bar accepts CC-- 0301 indexable inserts; the SCLC holder form and the stated cutting height provide correct seating and clamping for this insert type. Is the tool right-hand or left-hand cutting? This boring bar is specified for right-hand cutting with a 95° cutting angle to suit common internal turning directions. What is the shank size and does it fit standard holders? The shank diameter is 8 mm, compatible with holders designed for that shank size and identified by the ISO designation S05H SCLCR. Can this bar reach deep bores given its overall length? With an overall length of 100 mm and a compact 5 mm cutting diameter, the tool is intended for confined bore access; actual reach suitability depends on the machine’s setup and holder choice. How heavy is the tool and does weight affect performance? The tool weighs 0.046 kg, which aids handling and contributes to reduced centrifugal influence in higher-speed rotations, supporting stable cutting conditions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of fine M2.2 threading, a compact 3 mm diameter and a short 5 mm overall length for precise, space-saving fixing solutions — order directly via Metav Werkzeuge or consult our specialists for application advice. Torx screw TC059TM — M2.2 thread, 3 mm diameter (Teknik Makina) A Torx screw intended for small-scale assemblies and fixtures, providing compact fixation for precise mechanical and electronic components; compatible with a T7 hex key. Fine M2.2 thread for precise assemblies Compact 3 mm diameter for tight spaces Short 5 mm overall length for shallow joins 60° head angle suitable for countersunk seating Precision fit for compact assemblies The compact design of this fastener delivers a reliable mechanical connection where space is at a premium. With a M2.2 thread and a 3 mm diameter, the component is tailored for miniature housings, instrument fixtures and small machine parts. The fine thread pitch reduces the risk of material stress in thin-walled parts and enables controlled torque application during installation. In practice, this means cleaner assembly procedures and fewer rework cycles on densely packed assemblies. Secure seating and repeatable alignment A 60° head angle enables consistent countersunk seating in prepared holes, ensuring repeatable alignment across multiple fixings. The 5 mm overall length keeps the screw profile minimal while still delivering sufficient engagement for steel or alloy substrates when used with appropriate inserts or pre-tapped holes. For precision workshops and production lines, this translates into steadier joints and predictable torque behaviour during tightening operations. Tool compatibility and assembly workflow This fastener is specified for use with a T7 hex key, supporting standard hand and torque-driver processes common in small-component assembly. Compatibility with a dedicated driver reduces the chance of cam-out and improves assembly speed on repetitive tasks, promoting efficient throughput on production benches. The concise geometry also minimises obstruction around the head, simplifying handling during automated or semi-automated assembly. For further specification or to secure supply of this Teknik Cutting Tools Torx screw (TC059TM), contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for prompt advice and ordering assistance Technical data Article number: TC059TM Name: Torx screw Manufacturer: Teknik Makina Facts Weight: 0.1 kg Diameter: 3 mm Thread: M2.2 Overall length: 5 mm Angle: 60° Features Suitable tool: Hex key T7 ECLASS: 21189290 FAQ Which driver fits this screw best? The screw is designed for use with a T7 hex key; the specification for the Teknik Cutting Tools Torx screw (TC059TM) indicates a T7 driver for secure engagement. What thread size does the screw use? This fastener uses a M2.2 thread, providing fine engagement for small components and precision assemblies. Is the head suitable for countersunk applications? Yes, the 60° head angle is intended for countersunk seating, giving repeatable alignment in prepared holes. For which applications is this fastener intended? The component is intended for compact assemblies and fixtures, such as small mechanical housings, instrument brackets and densely packed electronic assemblies. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable fastening for compact assemblies: combine metric consistency and secure Torx drive with a slim profile and predictable torque behaviour for efficient, repeatable production. Order the Torx screw directly via Metav Werkzeuge or ask our consultants if needed. Torx screw TC064TM — M3 thread, Torx drive (Teknik Makina) The Torx screw is a compact M3 fastener designed for secure mechanical joins where space is limited and repeatability matters M3 metric thread, precision-formed 3.8 mm head diameter for compact fit Torx drive compatible with T8 key Compact design for confined assemblies The compact geometry of this fastener, with a M3 thread, a head diameter of 3.8 mm and a total length of 6.2 mm, delivers a small installation footprint while preserving clamping strength. In practice, the reduced head diameter allows components to be fastened close to edges or inside tight housings without imposing bulky clearances. The metric specification supports interchangeability with standard M3 components, making procurement and inventory simpler and reducing assembly errors. This combination of dimensions ensures a predictable fit and easy integration into product designs where space efficiency is essential. Torque control and reduced cam‑out with Torx drive Equipped with a Torx T8 drive, the fastener enables improved torque transfer compared with slotted or Phillips drives, which helps avoid stripping and ensures consistent tightening across production runs. The Torx geometry engages the driver over a larger surface area, reducing the risk of cam‑out and making manual or powered assembly more reliable. For operations that specify a torque setting, this drive form supports controlled torque application, leading to fewer reworks and a steadier assembly process. Compatibility with a standard T8 tool streamlines maintenance and tool selection on the shop floor. Consistent production quality for repeatable results Manufactured by Teknik Makina and listed under TC064TM, this fastener is produced to metric tolerances that support uniform performance in series production. The precision dimensions promote consistent clamping behaviour and predictable mechanical characteristics across batches, which is particularly valuable in small‑part assemblies and electronics where tight tolerances matter. Although no coating or material specification is provided in the basic data, the screw’s metric conformity and Torx drive make it a straightforward choice for engineers seeking a compact, reliable solution for repeatable fastening tasks. For reliable, metric fastenings from Teknik Makina, request TC064TM through Metav Werkzeuge — our team in Emmerich provides stock and ordering support at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: TC064TM Name: Torx screw Manufacturer: Teknik Makina Facts Weight: 0.1 kg Diameter: 3.8 mm Total length: 6.2 mm Angle: 60° Thread: M3 Special features Torx drive, compatible with T8 key Metric M3 thread Compact head diameter for tight spaces FAQ What thread does this screw use? The TC064TM is supplied with a M3 metric thread suitable for standard M3 mating parts. Which driver size is required for the Torx drive? The fastener uses a Torx T8 drive; a T8 tool engages the recess correctly. What are the main dimensions of the fastener? The product data shows a head diameter of 3.8 mm and a total length of 6.2 mm for the TC064TM Torx screw. Is the material or coating specified for this screw? No material or coating is specified in the provided technical data for this screw; the entry lists dimensions, thread form and drive type only. Is this fastener suitable for precision assemblies? Yes. The metric dimensions and Torx drive make TC064TM appropriate where compact size and repeatable torque control are priorities. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact Torx screw that combines secure Torx T15 drive compatibility, a standard M4.5 thread and a countersink-friendly 60° head for consistently flush assemblies; order directly through Metav Werkzeuge or contact our consultants for specification support. Torx screw TC080TM — M4.5 × 11 mm, Torx T15 by Teknik Makina A Torx screw intended for standard workshop and assembly applications, offering an M4.5 thread and an 11 mm total length for reliable, repeatable fastening. Torx T15 drive compatible Thread M4.5 for standard fittings 11 mm total length 60° head angle for flush fastening Precise fastening for repeatable assembly results The compact fastener delivers mechanical reliability by combining a standard M4.5 thread with a short, controlled shank. The combination of a metric thread and a shallow overall length results in predictable clamping behaviour when used in pre-tapped holes or with matching threaded inserts. Matching the drive to a Torx T15 tool reduces cam‑out and torque loss during installation, contributing to consistent joint preload and fewer reworks. The specification supports process stability in small- to medium-scale assemblies where repeatability matters. Tool compatibility and installation efficiency The head geometry, given as a 60° angle, indicates suitability for countersunk or flush mounting where a low-profile finish is required. The Torx interface paired with a T15 driver enables efficient torque transfer and precise positioning, which speeds up automated and manual assembly steps alike. Reduced cam‑out extends driver bit life and lowers the incidence of damaged heads; the fastener’s dimensions (diameter 6.2 mm, thread M4.5, total length 11 mm) make it a practical choice for compact components and confined installation spaces. Workshop readiness and supply reliability Technical simplicity and conformity to familiar standards make this fastener straightforward to specify across procurement and production documents. The item’s listed mass (0.1 kg) is useful for logistics and inventory planning. Sourcing via a trusted partner helps maintain continuity of supply: Metav combines a broad product range with a quality filter at its Emmerich site, backed by long‑standing industry relationships and an established customer base of over 48,000 customers. For procurement planners and workshop managers, the combination of standard sizing and trusted distribution reduces administrative overhead and supports uninterrupted assembly operations. For availability checks, compatibility advice or to secure Teknik Makina stock through Metav Werkzeuge, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for prompt assistance Technical data Article number: TC080TM Designation: Torx screw Manufacturer: Teknik Makina eClass: 21189290 Facts Diameter: 6.2 mm Thread: M4.5 Total length: 11 mm Head angle: 60° Weight: 0.1 kg Special features Torx drive: T15 compatible Countersink geometry indicated Standard workshop fastener FAQ What driver fits this screw? The Torx screw TC080TM is compatible with a Torx T15 driver for optimal torque transfer and reduced cam‑out. Is the head suitable for a flush finish? Yes, the head angle of 60° on the TC080TM is intended for countersunk applications and provides a low‑profile finish when installed correctly. What are the core dimensions of the fastener? Diameter 6.2 mm, thread M4.5 and total length 11 mm are the primary dimensions of the TC080TM. Is this fastener suitable for automated assembly? The Torx interface (T15) and standard metric thread make the TC080TM well suited to both manual and automated assembly processes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact fastening solution with a standard M5 metric thread and a short 9 mm overall length for secure, space-saving joins; the small 6.3 mm diameter shank ensures precise alignment in narrow assemblies. Order the part directly via Metav Werkzeuge or request guidance from their consultants for integration into production. Screw TC048TM by Teknik Makina — M5 thread, 9 mm length A Screw TC048TM engineered for fastening shims and U‑plates in workshop and industrial assemblies, offering a compact profile for tight installation spaces M5 metric thread for standard fittings 9 mm total length for compact assemblies 6.3 mm diameter shank for precise alignment Compatible with 4 mm Allen key Precise fit for compact assemblies The M5 metric thread paired with a 9 mm overall length delivers a reliable fastening solution where space is limited. This configuration reduces protrusion while maintaining clamping force, which benefits machine housings, bracketry and layered fixtures. The 6.3 mm shank diameter aids repeatable positioning, so components remain true to alignment during assembly and service, supporting consistent production quality with minimal adjustment. Straightforward installation that speeds assembly Installation is simplified by compatibility with a 4 mm Allen key, enabling rapid torque application and straightforward access even in confined areas. The hex drive arrangement reduces cam‑out and makes manual or machine-assisted tightening efficient. For production environments, this translates to reduced assembly time per unit and lower risk of damage to mating parts, a clear operational advantage during high‑volume or repetitive tasks. Application guidance for shims and U‑plates Designed specifically for use with shims and U‑plates, the fastener is suited to precision positioning and repeatable fixture setups. The short overall length is optimal where countersinking is undesirable or where minimal clearance is required above the mating surface. In retrofit and maintenance scenarios, the screw’s dimensions support quick replacement and reinstatement of alignment, preserving component tolerances without elaborate disassembly. Traceability and workshop logistics Marked with SKU TC048TM, this fastener can be tracked within inventory and bill‑of‑materials systems to simplify reordering and quality checks. At just 0.1 kg per unit in bulk handling terms, storage and handling requirements are modest. Supplied by Teknik Makina and distributed via Metav Werkzeuge, the part integrates into existing supply chains with predictable availability and straightforward documentation for purchasing and audit trails. For dependable fastening components from Teknik Cutting Tools, contact Metav Werkzeuge for order placement and tailored advice — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: TC048TM Designation: Screw for shim / U‑plate Manufacturer: Teknik Makina Facts Weight: 0.1 kg Diameter: 6.3 mm Thread: M5 Total length: 9 mm Special features Intended for shims and U‑plates Hex drive compatible with 4 mm Allen key Compact profile for narrow assemblies FAQ What are the main dimensions and thread of this fastener? The screw features an M5 thread with a 6.3 mm shank diameter and a 9 mm total length, suitable for compact fastening tasks. Which tool is required to install the fastener? Installation is performed with a 4 mm Allen key, which matches the hex drive of the screw for secure tightening. Can this screw be used with shims and U‑plates? Yes — the design is intended specifically for shims and U‑plates and provides precise alignment for layered assemblies. How is the item identified for reordering and inventory? The part is listed under SKU TC048TM, allowing straightforward tracking in procurement and stock systems. Who manufactures and distributes this screw? Manufactured by Teknik Makina and supplied through Metav Werkzeuge, the component is intended for workshop and industrial use. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine secure M2.5 threading with a compact 6.5 mm overall length for reliable, space-saving fastening in precision assemblies; order the TC061TM Torx screw directly via Metav Werkzeuge or contact our consultants for application guidance. Torx screw TC061TM – M2.5 thread, 3.5 mm diameter | Teknik Makina The Torx screw TC061TM is a compact fastener engineered for fine mechanical assemblies and constrained installation spaces, suitable where small, precise fixings are required. M2.5 metric thread for fine assemblies 3.5 mm head diameter for compact fit 6.5 mm overall length for shallow fixings Compatible with hex key T8 Precise thread geometry for dependable connections The compact fastener is designed around an M2.5 metric thread, which provides consistent engagement in small component housings and precision fixtures. A fine thread like M2.5 delivers predictable clamping force with reduced risk of loosening under light dynamic loads, making it well suited to instrument housings, control panels and delicate assemblies. The nominal head diameter of 3.5 mm and the short 6.5 mm overall length reduce protrusion and allow secure seating in shallow countersunk or through-hole applications. The specified 50° head-related angle supports secure torque transfer and consistent seating geometry when paired with compatible fastener seats. These dimensional details enable engineering teams to predict fit and tolerance behaviour and to integrate the fastener into CAD models and BOMs without ambiguity. Tool compatibility and efficient assembly workflow Installation efficiency is supported by a declared compatibility with hex key T8, so the fastener integrates smoothly with common workshop tool sets and automated assembly drives that accept T8 tooling. Where repeatable insertion speed and low-cycle torque control matter, the combination of compact dimensions and a standard driver interface speeds assembly and reduces handling time. For maintenance and disassembly procedures, the standardised drive size simplifies spare-part management. The screw’s lightweight specification (0.1 kg as an item reference) minimises additional mass in weight-sensitive assemblies and reduces transport and handling burdens when ordered in larger quantities. Clear specification of driver compatibility and dimensional parameters helps production planners select the correct feed and torque settings for reliable, repeatable results on the shop floor. Sourcing confidence and fit-for-purpose supply Sourced from Teknik Makina, the component is positioned for use in precision workshops and production environments where repeatability and part traceability matter. Procuring through Metav Werkzeuge adds the advantage of an established European distribution channel and a quality filter at the Emmerich hub, supporting reliable delivery and centralised purchasing for industrial buyers. The product’s concise dimensional set simplifies inventory classification and reduces the chance of installation errors: engineers and buyers can reference the M2.5 thread, 3.5 mm head diameter and 6.5 mm length when preparing assembly sheets or ordering spares. For applications that demand tight fitment and minimal clearance usage, this fastener offers a compact, industry-standard solution that aligns with efficient workshop logistics and quality-conscious procurement. For precise small-component fastening, choose the Teknik Makina TC061TM and contact Metav Werkzeuge for tailored procurement support and specification advice. Technical data Article number: TC061TM Manufacturer: Teknik Makina SKU: TC061TM Data Diameter: 3.5 mm Thread: M2.5 Overall length: 6.5 mm Angle: 50° Weight: 0.1 kg Special features Drive compatibility: hex key T8 Product type: Torx screw Intended use: precision assemblies, shallow fixings Origin: Teknik Makina FAQ What is the thread size of this fastener? The Teknik Makina Torx screw TC061TM is specified with an M2.5 metric thread for fine mechanical connections. Which driver fits the TC061TM? The TC061TM is listed as compatible with a hex key T8, enabling use with common T8 tooling for installation. What are the main dimensions to consider? Key dimensions are 3.5 mm head diameter, 6.5 mm overall length and a 50° head angle, which together determine seating and clearance requirements. Is the TC061TM suitable for confined or shallow spaces? Yes — the short 6.5 mm length and compact 3.5 mm head diameter make the TC061TM appropriate for shallow fixings and restricted installation areas. Can this fastener be used in precision instrument assemblies? The fine M2.5 thread and compact geometry make the TC061TM appropriate for many precision assemblies where small, reliable fastenings are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, precision-made locating solution that combines consistent dimensional accuracy and fast integration into cutting-tool assemblies — ideal for streamlining insert changes and reducing set-up time. Order or request procurement support via Metav Werkzeuge for reliable supply and delivery. Hollow pin TS-3TM — tubular locating pin for indexable inserts, Ø 6.65 mm, 5.5 mm length (Teknik Cutting Tools) Hollow pin for securing indexable inserts in cutting tool pockets; suited to industrial and workshop use Precision Ø 6.65 mm fit Short overall length 5.5 mm Suitable for indexable inserts Tubular locating design Consistent locating and repeatability for production workflows The hollow pin TS-3TM is manufactured to deliver reliable locating performance in insert-mounted cutting systems. With a nominal diameter of Ø 6.65 mm and an overall length of 5.5 mm, the component provides a defined contact geometry that reduces play between the insert and the tool pocket. This dimensional consistency shortens set-up time and helps maintain repeatable tool position between insert changes, supporting efficient machining cycles in small-batch and serial production alike. Compact form factor that reduces interference and simplifies assembly A short, tubular locating element like the TS-3TM minimises protrusion into the work area while still delivering secure positioning. The tubular design allows easy insertion into appropriately prepared pockets and avoids excessive bulk at the cutting edge. The low mass (approx. 0.1 kg) contributes negligible inertia, which is beneficial where multiple rapid insert changes or high-frequency indexing are required. Integration guidance and practical benefits for workshop teams For integration, match the pin diameter and length with the toolholder’s seat and the insert’s bore geometry to ensure correct engagement. The TS-3TM has been designed for straightforward placement in indexable-insert assemblies, supporting faster maintenance and less downtime. Where toolholder specifics differ, selecting the correct locating element avoids stress concentrations and maintains consistent cutting performance. Reliability through professional sourcing and supply Procured via Metav’s distribution channels, this locating pin benefits from Metav’s quality control and stock management in Emmerich. Metav supplies a broad range of precision components and ensures dependable delivery to workshops and industrial customers, helping to consolidate sourcing and reduce supplier complexity. Contact Metav Werkzeuge for technical compatibility checks and procurement of the TS-3TM hollow pin; phone +49 2822 7131930 or email info@metav-werkzeuge.com for immediate assistance Technical Data Article number: TS-3TM Name: Hollow pin (Rohrstift) Manufacturer: Teknik Makina Facts Diameter: 6.65 mm Overall length: 5.5 mm Weight: 0.1 kg SKU: TS-3TM Special features Suitable for indexable inserts Tubular locating design Compact form for minimal protrusion FAQ What is the primary application of this locating pin? The TS-3TM hollow pin is intended to locate and position indexable inserts in tool pockets, enabling repeatable seating and stable cutting geometry. Which dimensions are critical when selecting this pin? Key dimensions are the Ø 6.65 mm diameter and the 5.5 mm overall length; the weight is approximately 0.1 kg for handling and inventory considerations. Will the TS-3TM fit my existing toolholder? Compatibility depends on the toolholder pocket and insert bore dimensions; the TS-3TM is designed for standard insert mounting scenarios but checking seat geometry against Ø 6.65 mm and 5.5 mm is recommended. Is this component suitable for industrial workshop use? Yes — the TS-3TM is designed for robust integration into workshop and production settings where consistent locating and quick insert changes are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, industry-standard fixing solution with an M3 thread, a Ø 5.5 mm profile and a total length of 6.7 mm for dependable assembly performance; order through Metav Werkzeuge or consult the team for application advice. Screw for Shim — M3 thread, compact fixing for U-plate applications by Teknik Cutting Tools The Screw for Shim is a compact fastening component designed for secure attachment of U-plates and shims in workshop and assembly environments, offering a standard metric thread for consistent, repeatable installation. M3 thread for standard metric fittings Ø 5.5 mm compact head diameter Overall length 6.7 mm for tight assemblies Compatible with T15 hex key Precise fixing that keeps assemblies true A small, accurately produced fastening element delivers measurable benefits in repeatable assemblies. The M3 thread provides a familiar metric interface that simplifies integration into tapped holes and standard fixtures, while the Ø 5.5 mm dimension defines a compact profile suitable for constrained spaces. This results in less play at the joint and a more stable overall structure, reducing the need for rework and improving process reliability. Reduced downtime through predictable installation Consistent geometry and a short overall length make this component favourable where speed and predictability matter. The 6.7 mm total length permits secure engagement without unnecessary protrusion, helping to avoid interference with mating parts. Compatibility with a T15 hex key streamlines assembly operations, enabling rapid torquing with common workshop tools and lowering the risk of stripping during installation. Easy sourcing and simple stock management The screw is lightweight and compact, which benefits both logistics and handling in production and maintenance stock. Delivered under SKU TC062TM, this component is readily specified for mounting shims and U-plates and is suitable for standard workshop use. The combination of standard metric thread, compact dimensions and proven tooling compatibility supports efficient procurement and spare-part strategies. For robust, compact fastening choose the Teknik Cutting Tools M3 screw and contact Metav Werkzeuge in Emmerich for tailored supply and technical guidance — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: TC062TM ECLASS: 21189290 Manufacturer: Teknik Cutting Tools Facts Diameter: 5.5 mm Thread: M3 Overall length: 6.7 mm Weight: 0.1 kg Special features Compatible with T15 hex key For Shim / for U-plate Compact profile for tight assemblies FAQ What size and thread does this fixing use? The Screw for Shim is specified with an M3 thread and a diameter of 5.5 mm, listed under SKU TC062TM. Is a special tool required for installation? Installation is carried out with a T15 hex key, making the component compatible with common workshop tooling. What applications suit this fastener? The component is intended for securing shims and U-plates where a compact, metric-threaded fastening is needed; it is suitable for general assembly and workshop use. Which company produces this part? This fastening component is manufactured by Teknik Cutting Tools and distributed under SKU TC062TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable fastening performance is achieved through the combination of a Torx drive and a metric M4 thread, delivering secure joints in confined assemblies; the compact 11 mm overall length and 6.7 mm diameter support space-saving designs. Order via Metav Werkzeuge or consult the technical team for application guidance. Torx Screw — M4 thread, 11 mm overall length (Teknik Makina) A Torx Screw engineered for reliable mechanical fastening in industrial and workshop settings, offering a compact profile and Torx-compatible drive for stable torque transmission. Torx head for high torque transfer Metric M4 thread for standard fastening Compact 11 mm length for tight spaces 60° seat angle for precise seating Secure joints with compact dimensions The compact profile combines a metric M4 thread with a modest overall length of 11 mm, making this fastener well suited to assemblies where space is limited. The modest 6.7 mm diameter maintains a low profile without compromising clamping force; when paired with a properly sized threaded hole or insert, the result is a consistent mechanical connection. The technical design supports repeatable installation in production or repair tasks and reduces the need for post-assembly rework. Reliable torque transfer and tool compatibility A Torx drive provides superior torque transmission compared with slotted or Phillips heads, reducing cam-out and wear on both the fastener and the tool. This component is compatible with a T15 Torx key, enabling efficient installation with power or hand tools commonly used in workshops. The 60° seating angle facilitates accurate countersinking where required, ensuring the fastener sits flush and distributes load evenly across the mating surface. Assembly efficiency and procurement confidence From a procurement perspective, the straightforward specification—M4 thread, 11 mm length, 6.7 mm diameter—simplifies component selection and inventory management. The item’s modest mass (0.1 kg) supports easy handling and predictable packaging. Specifiers and purchasing teams benefit from the clear technical parameters for CAD models, bill of materials and quality checks, while production staff gain a dependable, repeatable fastener for everyday applications. For workshop-grade fastening and bulk supply, trust Teknik Makina’s Torx screw and contact Metav Werkzeuge for procurement and technical clarification at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: TC078TM Manufacturer: Teknik Makina ECLASS: 21189290 Weight: 0.1 kg Dimensions & thread Diameter: 6.7 mm Thread: M4 Overall length: 11 mm Angle: 60° Design & compatibility Drive type: Torx Compatible key: T15 Torx key FAQ What driver is required for installation? This Torx screw (Teknik Makina, fastener, SKU TC078TM) is driven with a T15 Torx key or a compatible T15 Torx bit for power tools. What are the thread and external dimensions? The fastener has a metric M4 thread, an overall length of 11 mm and a diameter of 6.7 mm as specified for SKU TC078TM from Teknik Makina. How does the 60° angle affect seating? The 60° angle defines the seating geometry to allow a flush countersunk fit; when combined with appropriate matching countersink geometry, the screw distributes load evenly. Is this fastener suitable for compact assemblies? Yes, the short 11 mm overall length and modest 6.7 mm diameter make this Torx screw (Teknik Makina, SKU TC078TM) suitable for confined or low-profile assemblies. What advantages does a Torx drive provide over other head types? A Torx drive reduces cam-out and allows higher torque transfer with less tool wear, improving installation reliability for recurring production tasks such as those performed with SKU TC078TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of precise clamping geometry, compatibility with Korloy MGM 3 inserts and a compact 150 mm overall length for efficient left-hand parting operations; order the parting tool holder directly via Metav Werkzeuge or ask our consultants for application advice. Teknik Makina parting clamp holder — left-hand, ISO 2525, for Korloy MGM 3 inserts Parting clamp holder for left-hand cut-off and grooving applications in turning processes, designed for use with Korloy MGM 3 inserts and ISO 2525 shank systems. Left-hand cutting direction compatible Fits Korloy MGM 3 indexable inserts 25 mm cutting head width for stability Max cutting diameter Ø80 mm supported Stable clamping for reliable parting results A compact clamp holder constructed to deliver consistent clamping force and repeatable parting cycles. The combination of a 25 mm cutting head and an ISO 2525 shank provides a stable interface between machine and tool, reducing chatter and extending insert life. This rigidity translates into measurable process benefits: fewer interrupted cycles, improved surface finish and less insert wear when machining non-critical steels and general workshop materials. The product is supplied in a compact format weighing 0.717 kg, which simplifies handling and tool change procedures on busy machining centres. Designed for efficient insert usage and quick set-up The holder accepts Korloy MGM 3 indexable inserts and is optimised for a 3 mm cutting width, allowing precise parting with minimal material loss. The design supports a maximum cutting depth of 17 mm for the parting blade, while the shaft cutting length of 25 mm gives adequate engagement for most facing and grooving set-ups. Clear, industry-standard labelling such as the ISO 2525 designation and compatibility note for 3C-L (60–80) bar sizes helps planning and inventory management, speeding up tooling selection and reducing set-up time at the lathe. Compact overall length with practical machining capacity With an overall length of 150 mm and a supported maximum machining diameter of Ø80 mm, the holder is well suited to confined toolposts and smaller lathes where space is at a premium. The 40 mm cutting height ensures correct insert support, improving chip control and operator confidence during repetitive cut-off tasks. The left-hand cutting orientation is particularly useful for specific machine arrangements and workpiece feed directions, enabling the holder to be integrated seamlessly into established turning programmes. For tailored advice on using this Teknik Makina parting clamp holder (SKU D802TM) with Korloy MGM 3 inserts and to arrange supply via Metav Werkzeuge in Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt technical guidance and order placement Technical data Article number: D802TM Manufacturer: Teknik Makina Facts Cutting head width: 25 mm Cutting width: 3 mm Cutting height: 40 mm Maximum cutting diameter: Ø80 mm Stech depth (max): 17 mm Shaft cutting length: 25 mm Overall length: 150 mm Weight: 0.717 kg Shank designation: ISO 2525 Versions / Special features Left-hand cutting direction Compatible with Korloy MGM 3 inserts Bar compatibility: 3C-L (60–80) Suitable for parting and grooving applications Compact design for restricted toolpost space FAQ Which inserts fit this parting clamp holder? The holder is configured for Korloy MGM 3 indexable inserts; Teknik Makina’s parting clamp holder (SKU D802TM) is specified to accept that insert family. What is the maximum supported workpiece diameter? Maximum cutting diameter is Ø80 mm, enabling secure parting operations up to that workpiece size with the recommended insert and set-up. Is the cutting direction left-hand or right-hand? This clamp holder is designed for left-hand cutting direction, suitable for machines and feed arrangements that require that orientation. How deep can the parting blade engage? The parting blade supports a maximum stech depth of 17 mm, giving adequate depth for standard grooving and cut-off tasks. What are the shank and overall dimensions? Shank designation is ISO 2525 with an overall length of 150 mm, optimised for compact toolposts and easy tool changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust shank design, precise insert compatibility and efficient chip evacuation for reliable T-slot machining; order the cutter directly via Metav Werkzeuge or consult the technical team for suitability. T-Nut Cutter TKC251TM — 60 mm diameter, 25 mm shank | Teknik Makina The T-Nut Cutter TKC251TM is a high-capacity T-slot cutter designed for producing secure T-nut profiles in metalworking and fixture production. High-efficiency 60 mm cutting diameter 4 cutting edges for smooth material removal 25 mm shank for solid clamping stability Precision and stability for consistent T-slot profiles The TKC251TM is engineered to deliver a consistent T-slot geometry thanks to its 60 mm diameter and stable 25 mm shank. The cutter’s 4 flutes promote balanced cutting forces and help to reduce chatter, while the specified cutting angle 55° supports accurate sidewall formation. These design choices combine to reduce rework and ensure repeatable part quality, particularly where secure fastening or locating elements depend on uniform T-nut dimensions. Weight and balance are tuned to support steady spindle performance; the tool mass of 0.583 kg contributes to vibration damping without compromising responsiveness. Fast insert changes and clarified insert compatibility This T-slot cutter accepts DCMT 11T3 indexable inserts, a common and versatile geometry for side-and-face operations. The indexable system allows worn cutting edges to be rotated or replaced rapidly, reducing downtime compared with brazed-tip tools. Fixing is secured by a M3.5x9 Torx screw and tightened with a T15 key, enabling repeatable clamp torque and straightforward servicing at the bench. For users unfamiliar with insert codes: DCMT 11T3 denotes an indexable, trigon-shaped insert with a nominal size suitable for the cutter’s pocket; the set-up supports precise chip breaking and economical edge indexing. Efficient machining workflow and workshop advantages With an overall length 120 mm and a cutting length 35 mm on the shaft, this cutter is configured for deep, stable engagement in common T-slot operations. The combination of robust shank diameter and multiple cutting edges contributes to improved surface finish and faster feed rates under suitable machine conditions. The cutter’s geometry is intended to provide a balance between material removal rate and tool life, supporting efficient batch production without sacrificing profile accuracy. Supplied technical data and the tool’s indexable insert system make it practical to plan replacement cycles and maintenance in a production schedule, helping workshops maintain throughput and predictable quality. Contact Metav Werkzeuge in Emmerich for procurement advice and accurate specification matching for the Teknik Makina T-slot cutter TKC251TM (SKU TKC251TM) Technical data SKU: TKC251TM Manufacturer: Teknik Makina Compatible inserts: DCMT 11T3 Core dimensions Diameter: 60 mm Overall length: 120 mm Shank diameter: 25 mm Cutting length (shaft): 35 mm Number of flutes: 4 Weight: 0.583 kg Cutting angle: 55° Design & compatibility Torx key: T15 Torx screw: M3.5x9 Files available: IDs 62de7eec33927e49dbf32794, 62de7e5c0f56dbb4de4dbf10 FAQ What inserts fit this T-slot cutter? The cutter uses DCMT 11T3 indexable inserts; these are compatible with the cutter’s insert pocket and support economical edge indexing. Can the cutter be clamped in a standard 25 mm toolholder? The tool features a 25 mm shank, which is intended for secure clamping in holders or collets rated for that diameter. What is the significance of the 4 flutes on this cutter? Four cutting edges distribute cutting forces evenly, improving surface finish and reducing vibration during T-slot machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of reliable 45° cutting geometry and simple, secure mounting to improve cycle consistency in finishing operations; the head accepts SEET R245 12T3 indexable inserts and features a 22 mm shank for straightforward toolholder compatibility. Order the item directly via Metav Werkzeuge or consult the team for application advice. Planmesserkopf T435TM — 45° corner milling head with SEET R245 compatibility (Teknik Makina) A Planmesserkopf designed for precise 45° corner and face milling using SEET R245 12T3 indexable inserts in industrial turning and milling setups 45° cutting geometry for accurate corner milling Compatible with SEET R245 12T3 indexable inserts 22 mm shank for standard toolholders Torx screw M3.5x8.5 supplied (T15) Predictable corner geometry for consistent part quality The 45° cutting arrangement delivers a predictable engagement with the workpiece, reducing variation in corner radii and improving assembly fit. With the 45° cutting angle and support for SEET R245 12T3 indexable inserts, the head converts insert performance into repeatable surface results. Indexable inserts are replaceable cutting edges that allow fast restoration of cutting performance without regrinding; this lowers machining downtime and keeps tool costs controllable over long production runs. The combination of controlled geometry and replaceable inserts supports higher first-pass quality and fewer rework cycles. Fast integration with existing toolholders and straightforward clamping Designed for compatibility, the head uses a 22 mm shank for secure seating in common holders and a single Torx screw M3.5x8.5 (key size T15) for insert clamping and replacement. This simple interface reduces changeover complexity on the shop floor and shortens tool-change routines. The tool’s 63 mm diameter and balanced mass (approx. 0.815 kg) contribute to stable running at typical spindle speeds, helping to maintain surface finish while limiting vibration. Where modularity and quick servicing are priorities, this corner milling solution enables efficient interaction with standard clamping systems and established insert portfolios from recognised manufacturers. Engineered for repeatable shop-floor performance and low-maintenance operation Built for frequent insert changes and consistent cutting conditions, the milling head supports five cutting edges and a compact overall length of 50 mm, keeping the cutting forces well managed in finish operations. The accessible Torx fastening ensures secure retention and straightforward maintenance, while the head’s compatibility with insert suppliers such as Sandvik, XTC and ZCC broadens sourcing options. Backed by Metav’s quality filter in Emmerich, the component is offered with reliable logistics and technical support, helping procurement and production teams keep tool inventories lean without compromising on precision. Contact Metav Werkzeuge to discuss application suitability for the T435TM corner milling head, confirm compatibility with existing toolholders or to request a tailored supply recommendation from our specialists at the Emmerich site Technical data SKU: T435TM Manufacturer: Teknik Makina Product name: Planmesserkopf for SEET 12T3 R245 indexable inserts Suitable inserts: SEET R245 12T3 Compatible insert manufacturers: Sandvik, XTC, ZCC Cutting angle: 45° Shank diameter: 22 mm Diameter: 63 mm Overall length: 50 mm Number of cutting edges: 5 Weight: 0.815 kg Torx screw: M3.5x8.5 Torx key: T15 Core specifications Diameter: 63 mm Shank (aufnahme): 22 mm Overall length: 50 mm Cutting angle: 45° Number of cutting edges: 5 Weight: 0.815 kg Materials & compatibility Compatible with SEET R245 12T3 indexable inserts Supported insert manufacturers: Sandvik, XTC, ZCC Fastening hardware: Torx screw M3.5x8.5 (T15) Intended application: corner/face milling operations FAQ Which inserts fit this milling head? The head accepts SEET R245 12T3 indexable inserts; compatible brands listed for the T435TM include Sandvik, XTC and ZCC. What is the shank size and how is the insert secured? The T435TM features a 22 mm shank and the insert is secured with a Torx screw M3.5x8.5, tightened with a T15 key. Is the tool suitable for 45° corner milling tasks? Yes, the 45° cutting geometry has been designed for accurate corner and face milling, providing consistent engagement and repeatable corner radii. How many cutting edges and what are the key dimensions? The unit supplies 5 cutting edges, a 63 mm diameter and an overall length of 50 mm, with a mass of approximately 0.815 kg for stable operation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine precise 45° cutting geometry with Palbit SNKX/ONHX compatibility and a compact 22 mm mounting for consistent facing performance; order directly via Metav Werkzeuge or consult our specialists for application advice. Facing cutter head T629TM – 45° geometry for SNKX 1606 / ONHX 0606 indexable inserts (Teknik Makina) The Facing cutter head T629TM is a compact 45° tool holder designed for efficient facing and finishing with SNKX 1606 and ONHX 0606 indexable inserts 45° cutting geometry for smooth facing Compatible with SNKX 1606 and ONHX 0606 inserts 63 mm diameter for stable machining 22 mm mounting bore for secure clamping Five cutting edges for continuous productivity High-performance facing with proven insert compatibility The T629TM delivers a controlled cutting action through its 45° cutting geometry, which reduces radial forces and supports stable chip formation. Designed for use with SNKX 1606 and ONHX 0606 indexable inserts (Palbit compatible), the head ensures predictable cutting behaviour and repeatable surface quality. This specification is suitable where consistent facing finish and cycle-time reductions are required, translating technical data into measurable production gains. Secure mounting and robust construction for reliable operation A compact 22 mm bore combined with a 63 mm diameter provides a rigid interface that minimises runout and vibration during cutting. Clamping is achieved with M5x12 Torx screws tightened using a T20 key, enabling quick insert changes and repeatable torque values. The head’s balanced geometry and modest mass (0.776 kg) support stable spindle loads and contribute to longer tool life and predictable machining parameters. Efficient tool life and straightforward maintenance Equipped to carry five cutting edges, the head allows a sequence of indexable insert positions before replacement, lowering downtime and tool-handling frequency. The modular design simplifies insert access, while the use of standard SNKX/ONHX inserts keeps consumable logistics simple. The result is an optimised cost-per-part ratio and fewer interruptions — benefits that directly affect workshop throughput and operational efficiency. Applications and operational advantages This facing cutter head is intended for facing and finishing operations where SNKX 1606 / ONHX 0606 inserts are already specified. The combination of Palbit insert compatibility and the head’s geometry makes it suitable for batch production and toolroom setups that demand reliable repeatability. Installation and changeover procedures are straightforward, supporting fast set-up in mixed-production environments without complex adjustments. For dependable 45° facing with Teknik Makina build quality, contact Metav Werkzeuge for tailored advice and fast dispatch from Emmerich — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T629TM Manufacturer: Teknik Makina Product: Facing cutter head (45°) for SNKX 1606 / ONHX 0606 Facts Diameter: 63 mm Mounting bore: 22 mm Overall length: 50 mm Weight: 0.776 kg Cutting angle: 45° Number of cutting edges: 5 Special features Compatible inserts: SNKX 1606, ONHX 0606 Compatible insert manufacturer: Palbit Torx screw: M5x12 Torx key size: T20 SKU: T629TM FAQ What inserts fit this cutter head? The facing cutter head accepts SNKX 1606 and ONHX 0606 indexable inserts; Palbit-brand inserts are listed as compatible for this tool. Which toolholder bore is required for mounting? Mounting requires a 22 mm centre bore; the 22 mm mounting bore provides secure clamping and minimal runout for the T629TM. How many cutting edges does the head provide? The head carries five cutting edges, allowing multiple index positions before insert replacement and improving uptime. What torque connection is used for insert retention? Inserts are secured with M5x12 Torx screws, tightened using a T20 key for consistent clamping force. Is the head suitable for heavy-duty facing? The 45° geometry and 63 mm diameter offer stable performance for facing tasks where SNKX/ONHX inserts are appropriate; assess process parameters to confirm suitability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of 90° cutting geometry, a 63 mm body diameter and a 22 mm shank to secure stable, repeatable corner turning. Benefit from compatibility with ANHX 1004 indexable inserts and reliable mounting using the M3x7 Torx fastening. Order the tool directly via Metav Werkzeuge or consult the advisors for application-specific guidance. Eckmesserkopf — Corner cutting head with 90° geometry for ANHX 1004 indexable inserts (Teknik Makina) The Eckmesserkopf is a compact corner cutting head engineered for precise 90° turning operations using ANHX 1004 indexable inserts; ideal where rigidity and repeatability matter in production and jobbing shops. 90° cutting angle for precise corner turning Compatible with ANHX 1004 indexable inserts 63 mm body diameter for rigid stability 22 mm shank diameter for secure mounting Consistent geometry for predictable machining results The corner cutting head delivers a 90° cutting angle combined with a Ø63 mm body to reduce vibration and deflection during side and face turning. The hardened connection to the machine spindle and the 22 mm shank ensure a secure fit, translating spindle power into cutting performance with minimal loss. This design yields repeatability across batches and reduces scrap rates by stabilising chip formation and tool engagement. Fast insert changes and secure clamping cut downtime Compatibility with ANHX 1004 indexable inserts and the Palbit insert form means insert swaps are straightforward and standards-based. The head uses an M3x7 Torx fastening and a T8 Torx key for positive clamp torque, which keeps the insert seated reliably. Reduced tool-change time and dependable clamping improve uptime and support consistent cycle times on turning centres. Built for everyday workshop use with dependable handling With a modest mass of 0.638 kg and a compact overall length of 40 mm, the head is easy to manoeuvre during tool set-up yet robust enough for repeated operation. The configuration features seven cutting edges, promoting efficient indexing strategies where multi-edge inserts are used. The combination of compact dimensions and a rigid interface supports both short overhangs and close-tolerance face turning. Practical benefits for purchasing and inventory decisions Choosing this corner cutting head simplifies tooling logistics: it fits a common insert format and fastener type, helping standardise the tooling pool. The technical profile — Ø63 mm, 22 mm shank, 90° geometry — supports wide applicability across medium-duty turning tasks, allowing procurement teams to reduce the number of specialised holders required on the shop floor. Select Teknik Makina’s corner cutting head for its proven geometry and compatibility, and contact Metav Werkzeuge to arrange supply or technical consultation directly from Emmerich. Technical data Article number: T658TM Manufacturer: Teknik Makina Facts Diameter: 63 mm Overall length: 40 mm Shank diameter: 22 mm Weight: 0.638 kg Cutting angle: 90° Cutting edges: 7 ECLASS: 21181015 Features Compatible inserts: ANHX 1004 Compatible insert manufacturer: Palbit Torx key size: T8 Torx screw: M3x7 Brand: Teknik Makina FAQ Which indexable inserts fit this cutting head? The Eckmesserkopf is designed for ANHX 1004 indexable inserts; Palbit-format inserts are compatible and recommended for correct seating and performance. What is the required shank or toolholder interface? This corner cutting head features a 22 mm shank diameter for secure mounting in compatible tool turrets or holders. Which fastening hardware is supplied or required? Clamping is achieved using an M3x7 Torx screw tightened with a T8 Torx key; the specification is included in the product details for workshop preparation. Is the head suitable for tight, repeatable corner turning? Yes — the 90° geometry, Ø63 mm body and compact 40 mm length provide rigidity and repeatability for precise corner and face turning operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, precision-engineered corner tool head that combines a 90° cutting angle with a secure 22 mm shank for stable mounting; compatible with APKT 1705 indexable inserts and supplied with a Torx clamping screw for fast, reliable insert changes – order or discuss options with Metav Werkzeuge for technical guidance. Eckmesserkopf — corner tool head with 90° cutting angle for APKT 1705 indexable inserts by Teknik Makina Eckmesserkopf is a compact 90° corner turning head designed for reliable external turning and face‑off operations with APKT 1705 indexable inserts in CNC lathes and turning centres. 90° cutting angle for precise corner turning Compatible with APKT 1705 indexable inserts 22 mm shank diameter for secure mounting Torx M4x10 clamping screw, T15 key included Reliable precision and predictable machining results The compact head offers a 90° cutting angle that promotes consistent geometry when executing corner and shoulder cuts. The solid construction and precise mounting dimensions reduce vibration and runout, which in turn improves surface finish and tool life. Compatibility with APKT 1705 indexable inserts means the tool head fits a widely used insert format, simplifying inventory and replacement logistics. The result is predictable machining outcomes and reduced scrap rates. Secure clamping and rapid insert changes for uptime A 22 mm shank ensures a stiff connection to the holder or turret, minimising deflection under load. The assembly uses a Torx M4x10 clamping screw tightened with a T15 key, enabling quick, repeatable insert clamping without specialised tooling. This reduces downtime during changeovers and supports higher machine utilisation. For workshops seeking faster set‑ups, the combination of standardised screws and familiar insert geometry delivers practical gains in daily productivity. Compact design that suits crowded turrets and versatile applications With a head diameter of 63 mm, an overall length of 45 mm and a weight of 0.52 kg, this tool head is dimensioned for installations where space is limited yet stiffness remains essential. The design is particularly suitable for external turning, profiling and light facing tasks where a corner tool head is preferred. Built to accept inserts from established manufacturers such as Taegutec, it offers flexibility across jobs and materials while keeping the tool kit manageable. Practical advantages for purchasing and workshop logistics Using a standard insert type like APKT 1705 keeps consumable procurement straightforward and cost‑efficient. The compact footprint and standardised clamping screw mean fewer special spares are required, simplifying stock management. For buyers and production planners, the technical compatibility and repeatability translate directly into lower operational complexity and steady production throughput. Contact Metav Werkzeuge for tailored advice on integrating this Teknik Makina corner tool head into the production line or to request a quotation and compatibility checks Technical Data Article number: T554TM Manufacturer: Teknik Makina Compatible inserts: APKT 1705 Indexable Inserts Facts Cutting angle: 90° Shank diameter: 22 mm Head diameter: 63 mm Overall length: 45 mm Cutting edges: 6 Weight: 0.52 kg Special features Compatible with Taegutec inserts Torx clamping screw M4x10, key T15 For APKT 1705 indexable inserts 90° corner tool head design FAQ Which insert type fits this corner tool head? The tool head is designed for APKT 1705 indexable inserts and is compatible with inserts from manufacturers such as Taegutec. What are the mounting dimensions required? Mounting requires a spindle or turret accepting a 22 mm shank; the overall head diameter is 63 mm and the length is 45 mm. What clamping hardware is supplied with the tool head? The delivery references a Torx M4x10 clamping screw and the required T15 key for secure insert fastening. Is the tool head suitable for heavy roughing? The compact, stiff design is optimised for precision turning and finishing; for heavy roughing applications, consider holders and heads specified for higher cutting loads. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a stable machining setup with the combination of robust S50U MTQNR construction, compatibility with TNMG 1604 indexable inserts and a precise 107.5° cutting angle for predictable chip control and surface finish; order the tool through Metav Werkzeuge or consult our specialists for integration advice. MTWN for TNMG Indexable Inserts — S50U MTQNR boring bar (Ø63 mm, 350 mm) The MTWN for TNMG Indexable Inserts is a right-hand boring bar engineered for external turning applications with TNMG 1604 inserts, providing a heavy-duty shank and a geometry optimised for stable, repeatable chip formation. Right-hand turning for external operations Compatible with TNMG 1604 indexable inserts 63 mm outer diameter, 350 mm overall length Robust S50U MTQNR shaft, 50 mm shank diameter Stable cutting performance for demanding turning operations The design focuses on process stability by combining a substantial shank diameter (50 mm) with a large outer diameter (63 mm) and an overall length of 350 mm. This geometry reduces deflection during interrupted cuts and supports consistent concentricity in serial production. The ISO designation S50U MTQNR identifies a standardised interface for secure clamping; the heavier mass (weight 5.121 kg) contributes to vibration damping, which results in improved surface quality and extended insert life. Explanation of technical terms: a larger shank diameter increases rigidity, while the outer diameter and geometry influence how the tool presents the insert to the workpiece. Predictable chip flow and repeatable finishes With a defined cutting angle of 107.5° and compatibility with TNMG 1604 indexable inserts, the toolholder promotes controlled chip breaking and effective evacuation in general turning tasks. The right-hand cutting direction suits conventional turning setups. The combination of cutting geometry and insert fit improves reproducibility across batches, meaning fewer reworks and steadier cycle times — a rational benefit for production planning. Where material or feed ranges are critical, match the TNMG grade to the workpiece to balance wear resistance and toughness. Practical integration and workshop suitability The bar's ISO-style designation and the clear specification of shank and overall dimensions simplify tool selection and fixturing on lathes and turning centres. The item is intended for use with TNMG 1604 inserts; adapt the insert grade to the application (roughing, finishing, or mixed-duty). The specification includes a clamp-holder designation (value 16) for reference during tooling configuration. For workshops aiming to reduce supplier complexity, this robust holder reduces the need for frequent re-clamping and supports a predictable maintenance rhythm. For reliable heavy-duty turning with proven rigidity, contact Metav Werkzeuge to request detailed integration support or to place an order for the Teknik Cutting Tools MTWN boring bar (SKU K368TM) Technical Data SKU: K368TM Manufacturer: Teknik Makina Designation: Bohrstange / MTWN for TNMG Indexable Inserts ISO designation: S50U MTQNR Core measures Outer diameter: 63 mm Shank diameter: 50 mm Overall length: 350 mm Cutting height: 65 mm Weight: 5.121 kg Cutting angle: 107.5° Special features Compatible with TNMG 1604 indexable inserts Right-hand cutting direction Clamp holder designation: 16 Designed for external turning applications FAQ Which insert type fits this boring bar? The bar is designed for TNMG 1604 indexable inserts; select the appropriate TNMG grade for the material and cutting conditions. What are the key dimensions to check for machine compatibility? Check the 63 mm outer diameter, 50 mm shank diameter and 350 mm overall length against toolpost clearance and turret capacity. Is the bar suited to heavy interrupted cuts? The robust S50U MTQNR construction and substantial mass (5.121 kg) improve damping and make the bar suitable for heavier, interrupted turning routines when paired with the correct insert grade. Does the tool have a specified cutting direction? Yes — the tool is configured for right-hand cutting operations. What ISO designation helps with clamping and replacement? The S50U MTQNR ISO-style designation identifies the holder interface and assists with secure clamping and straightforward replacement. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining robust construction, a 50 mm shank and compatibility with TNMG 2204 inserts, this boring bar delivers stable cutting and consistent chip control for external turning. Order the S50U MTUNR boring bar directly via Metav Werkzeuge or consult our specialists for application advice. Teknik Makina S50U MTUNR Boring Bar – MTUN for TNMG indexable inserts, 50 mm shank A S50U MTUNR boring bar designed for right-hand external turning, ideal where stiffness, repeatable insert seating and extended reach are required. 50 mm shank for stable clamping Compatible with TNMG 2204 inserts 65 mm cutting height for deep cuts 350 mm overall length for extended reach Increased rigidity for consistent surface finish The combination of a 50 mm shank and a solid construction reduces vibration and improves stability during external turning. Reduced chatter leads to a better surface finish and longer insert life, which in turn lowers tooling costs and machine downtime. The ISO designation S50U MTUNR indicates a standard interface for secure mounting, guaranteeing predictable behaviour under moderate to heavy cutting conditions and simplifying integration into existing tool holders. Reliable insert seating and efficient chip control Designed specifically for TNMG 2204 indexable inserts, the holder provides a secure seating geometry that supports repeatable cutting results. The 93° cutting angle and 65 mm cutting height promote controlled chip flow and reliable cutting edge engagement, reducing the risk of unexpected insert movement. This combination is particularly effective for finishing and semi-finishing passes where dimensional consistency and repeatability are essential. Reach and tool geometry for versatile external machining With a 350 mm overall length and a tool diameter of 63 mm, the tool balances reach with rigidity to enable access into deeper workpieces without excessive deflection. The right-hand cutting orientation is optimised for standard lathe setups, providing straightforward use in conventional turning operations. The tool’s mass and dimensions make it suitable for medium-duty to demanding external boring tasks where a longer tool overhang is required while maintaining acceptable stiffness. Practical integration and operational benefits The bar’s compatibility with standard TNMG inserts simplifies inventory and reduces preparation time at the machine. A measured weight of 5.145 kg reflects its robust build and contributes to stable cutting dynamics once mounted. For production environments the reliable geometry and standard interface reduce set-up variation, supporting consistent cycle times and predictable maintenance intervals—factors that improve overall process efficiency and quality assurance. Contact Metav Werkzeuge to confirm fitment, verify insert selection and secure supply of the Teknik Makina S50U MTUNR boring bar from our Emmerich warehouse Technical Data SKU: K454TM Manufacturer: Teknik Makina ISO designation: S50U MTUNR Indexable inserts: TNMG 2204 Cutting direction: right Core measurements Shank diameter: 50 mm Cutting height: 65 mm Overall length: 350 mm Tool diameter: 63 mm Weight: 5.145 kg Cutting angle: 93° Special features MTUN for TNMG indexable inserts Right-hand turning tool ECLASS: 21180806 FAQ Which inserts fit this boring bar? The Teknik Makina S50U MTUNR boring bar is designed for TNMG 2204 indexable inserts and secures them with a standard MTUN seat for repeatable positioning. Is the cutting orientation right-hand or left-hand? This holder is configured for right-hand cutting, matching standard lathe turning directions. What are the principal dimensions to consider for mounting? Key dimensions include a 50 mm shank diameter, 350 mm overall length, 65 mm cutting height and a 63 mm tool diameter, with a weight of 5.145 kg. What ISO designation should be referenced when ordering tool holders? Refer to the ISO designation S50U MTUNR when matching the bar with compatible tool posts and adapters. For which operations is this tool best suited? The bar is intended for external boring and turning with TNMG inserts, offering a balance of reach and rigidity for finishing and semi-finishing cuts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of robust shank stability and reliable TNMG insert compatibility to maintain consistent turning quality and machine uptime. Order the component directly via Metav Werkzeuge or consult our specialists for process alignment and rapid supply. MTUN boring bar — S50U MTUNL left‑hand, for TNMG indexable inserts (Teknik Makina) The MTUN boring bar is a left‑hand external turning tool designed for use with TNMG 1604 indexable inserts, engineered to provide stable performance in lathe turning operations where rigidity and repeatable insert seating are required. Left-hand cutting direction For TNMG 1604 indexable inserts Shank diameter 50 mm, Ø63 mm body Overall length 350 mm ISO designation S50U MTUNL Stable clamping and vibration control for consistent cuts A solid shank and compact body reduce chatter and improve surface finish in manual and CNC turning operations. The combination of a 50 mm shank and Ø63 mm body provides high bending stiffness, which helps resist deflection under load. With an overall length of 350 mm and a mass of 5.15 kg, the tool maintains inertial stability that supports steady cutting conditions and predictable tooling behaviour. These design choices translate into fewer rework cycles and a more constant part quality when the set‑up is matched to machine capabilities. Fast insert changes and precise cutting geometry Designed to accept TNMG 1604 indexable inserts, the MTUN geometry secures repeatable seating and simple replacement, minimising downtime during tool changes. The bar carries the ISO designation S50U MTUNL, indicating the standardised shank and mounting form for straightforward integration into existing setups. A 93° cut angle and 65 mm cutting height are implemented to balance clearance and cutting engagement, allowing effective chip flow with commonly used TNMG grades. The standardised interface reduces setup time and supports predictable cutting behaviour across batches. Operational advantages and workshop integration Left‑hand orientation suits applications where reverse‑direction turning is specified or where tooling layouts require a left‑hand approach. The robust S50U configuration is compatible with standard heavy‑duty toolholders and is suited for rigid clamping arrangements. Specifying this bar simplifies inventory management by pairing a proven shank format with widely available TNMG inserts. For specification matching or to verify compatibility with a particular clamping system, technical staff at Metav Werkzeuge provide guidance and data to ensure correct integration into the production cell. For specification matching, delivery options and process advice on the Teknik Makina MTUN boring bar (S50U MTUNL, K526TM), contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or call +49 2822 7131930 for tailored assistance and prompt dispatch Technical data Article number: K526TM Manufacturer: Teknik Makina Product: MTUN for TNMG indexable inserts (bezeichnung_2_en) ISO designation: S50U MTUNL Cutting direction: left Core specifications Shank diameter: 50 mm Body diameter: 63 mm Overall length: 350 mm Cutting height: 65 mm Weight: 5.15 kg Cut angle: 93° Compatible insert: TNMG 1604 Design & features Left‑hand boring bar design S50U MTUNL shank designation Compatible with TNMG 1604 indexable inserts Robust mass for stable turning FAQ Which inserts fit this boring bar? The MTUN boring bar is specified for TNMG 1604 indexable inserts; the seating and clamp geometry are matched to that insert format. What is the shank diameter and does it suit heavy‑duty holders? The tool has a 50 mm shank and a Ø63 mm body, designed for rigid clamping and heavy‑duty holder compatibility; check the holder specification against the ISO designation S50U MTUNL. Is the cutting direction left or right? This bar is configured for left‑hand cutting direction as stated in the technical data and is intended for operations requiring a left‑hand approach. What is the overall length and how does that affect stability? The overall length is 350 mm; the moderate overhang together with the bar mass (5.15 kg) improves bending resistance and reduces vibration compared with longer, lighter bars. How does the 93° cut angle influence machining? A 93° cut angle provides a practical compromise between clearance and tool engagement, helping controlled chip flow and consistent surface finish when paired with appropriate TNMG inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Achieve precise internal turning with the combination of a robust 50 mm shank, 350 mm overall length and compatibility with WN-- 0804 indexable inserts — order the boring bar directly via Metav Werkzeuge or consult our specialists if needed. S50U MWLNR Boring bar — 50 mm shank, 350 mm overall length (Teknik Makina) A S50U MWLNR boring bar engineered for heavy-duty internal turning, optimised for MWLN-style indexable inserts and right-hand cutting applications. S50U MWLNR ISO shank, robust 50 mm Suitable for WN-- 0804 indexable inserts Right-hand cutting with 350 mm overall length Consistent clamping and concentricity for repeatable bore quality The bar is built around a 50 mm shank designed to provide stable clamping in standard holders, which reduces runout and improves surface finish during internal machining. With a 63 mm body diameter and a measured mass of 5.11 kg, the component delivers inertia that dampens vibration, so single-pass operations are more consistent. The ISO designation S50U MWLNR corresponds to established tooling standards, which simplifies integration into existing toolholders and reduces setup time. Geometry tuned for controlled chip flow and reliable cutting A defined 95° cutting angle and a cutting height of 65 mm ensure that the insert seat and rake geometry promote predictable chip formation when using WN-- 0804 inserts. The right-hand cutting configuration is matched to standard lathe feed directions and is recommended where radial stock removal is required. Key geometric choices are aimed at efficient material evacuation, which in turn extends insert life and lowers the frequency of tool changes. Workshop-ready length and handling for deep bores The 350 mm overall length provides extended reach for deeper internal turning tasks while preserving stiffness through its 50 mm shank. Machining longer bores is supported by the bar’s balanced dimensions, allowing for safer, more controlled passes without excessive deflection. The combination of reach and rigidity makes it suitable for medium-to-heavy duty internal operations in both single-part and small-batch production environments. Compatibility and straightforward tooling choices Designed for MWLN-style indexable inserts, the bar accepts WN-- 0804 inserts and pairs with common clamping systems (designation 08) for rapid insert changes and secure seating. The standardised interface reduces the need for bespoke tooling and enables straightforward replacement with widely available inserts. Where workshop logistics favour inventory reduction, the bar’s compatibility with established insert families simplifies procurement and stocking. For reliable internal turning with Teknik Cutting Tools' S50U MWLNR choose Metav Werkzeuge for advice and ordering — contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored technical guidance Technical Data Article number: K434TM Manufacturer: Teknik Makina Product: Boring bar (Bohrstange) Designation: MWLN for WN-- Indexable Inserts Facts Shank diameter: 50 mm Body diameter: 63 mm Cutting height: 65 mm Overall length: 350 mm Cutting angle: 95° Weight: 5.11 kg Special features Compatible inserts: WN-- 0804 ISO designation: S50U MWLNR Cutting direction: right-hand Clamping designation: 08 Designed for MWLN indexable inserts FAQ What insert type fits this boring bar? The boring bar is designed for WN-- 0804 indexable inserts and conforms to the MWLN insert family guidance for reliable seating and chip control. Is the bar suitable for deep internal turning operations? Yes; the 350 mm overall length and 50 mm shank provide reach and stiffness suited to deeper internal turning while maintaining acceptable rigidity. What is the recommended cutting direction? The tool is configured for right-hand cutting, matching standard lathe feed directions and conventional internal turning setups. Which ISO designation should be referenced for holder selection? Refer to S50U MWLNR as the ISO designation when selecting compatible toolholders or confirming holder compatibility. How does the bar affect vibration and surface finish? The larger 50 mm shank and 63 mm body diameter increase mass and damping, reducing vibration and improving finish compared with smaller-diameter alternatives. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Secure consistent shoulder milling results with the combination of 63 mm diameter, internal coolant and direct compatibility with APMT 1604 inserts; order the milling head directly via Metav Werkzeuge or ask our consultants if needed. 63 mm square shoulder milling head T245-1TM — internal coolant, APMT 1604 compatible | Teknik Makina The 63 mm square shoulder milling head T245-1TM is a compact, precision toolholder designed for robust shoulder and face milling tasks in production and jobbing shops, suited to APMT 1604 indexable inserts. 63 mm diameter for shoulder milling Internal coolant for improved chip evacuation Compatible with APMT 1604 indexable inserts 90° cutting angle for precise shoulder cuts Precise geometry for repeatable shoulder cuts The holder’s 63 mm diameter and 90° cutting angle deliver consistent, square shoulders and accurate face finishes across series production. The compact 45 mm overall length reduces overhang and increases rigidity, which in turn lowers vibration and improves surface quality. Designed to accept APMT 1604 indexable inserts, the holder is suitable for both roughing and finishing passes where repeatability and dimensional control are required. This combination of geometry and insert compatibility ensures predictable tool behaviour, helping to reduce rework and increase throughput in small-batch and serial machining. Improved cooling and chip management for longer life Equipped with internal coolant, the toolholder directs cutting fluid close to the cutting edge for effective cooling and chip evacuation. This targeted cooling reduces thermal load on the insert and cutting edge, slowing wear and preserving geometry over longer tool life. In practical terms, internal coolant contributes to more stable cutting conditions, especially during interrupted cuts or when machining difficult-to-cut materials. The result is fewer indexings, lower tooling costs per component and more consistent surface integrity on the workpiece. Secure clamping and service-friendly fastenings The clamping architecture uses a Torx T15 drive and M4x10 Torx screws for secure insert retention and straightforward maintenance. These standardised fastenings allow quick indexings and minimise downtime during tool changes. The toolholder’s balanced mass (approx. 0.578 kg) and compact form factor promote stable running at typical milling speeds, supporting higher feed rates where the cutter geometry and insert grade permit. For shops seeking predictable set-up times, the combination of standard Torx fixing and indexable insert compatibility simplifies inventory and reduces operator training needs. Ready for industrial workflows and supplier assurance Matched to Korloy-manufactured APMT 1604 inserts, the head is intended for industrial users who require a durable, serviceable solution for shoulder milling. The SKU T245-1TM identifies the exact configuration for procurement and toolroom records. Integrating this toolholder into a standardised tooling setup reduces complexity at the machine and streamlines reordering. For buyers focused on reliability and supply-chain transparency, Metav’s provision from Emmerich ensures centralised access to documentation and replacement parts suitable for production environments. For specification advice or to arrange supply of the T245-1TM square shoulder milling head, contact Metav Werkzeuge for tailored recommendations and prompt delivery from Emmerich. Technical data SKU: T245-1TM Product type: Square shoulder milling head For indexable inserts: APMT 1604 Core data Diameter: 63 mm Overall length: 45 mm Weight: 0.578 kg Cutting angle: 90° Number of cutting positions: 6 Special features Internal coolant: yes Compatible insert manufacturer: Korloy Torx key: T15 Torx screw: M4x10 Manufacturer: Teknik Makina FAQ What inserts fit this milling head? This milling head accepts APMT 1604 indexable inserts; the holder is specified for inserts from Korloy in the supplied configuration. Is the toolholder suitable for high-feed operations? The compact 45 mm overhang and 63 mm diameter provide increased rigidity for higher feed rates where insert grade and cutting data allow; confirm specific feed recommendations with the chosen insert. How is cooling provided to the cutting edge? Cooling is delivered via internal coolant channels that route fluid directly to the insert zone to improve heat control and chip evacuation. Which fasteners are used for insert clamping? Insert clamping uses a Torx T15 drive and M4x10 screws to ensure secure retention and straightforward servicing. Can this head be used for both roughing and finishing? Yes; with appropriate insert grades and cutting parameters, the holder supports both roughing and finishing operations thanks to its 90° cutting angle and stable geometry. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining reliable 90° corner geometry, secure 22 mm shank support and compatibility with APMT 11T3 indexable inserts, this turning head delivers consistent corner profiles and reduced setup time; order via Metav Werkzeuge or contact our consultants for technical guidance. Corner Turning Head T254TM — for APMT 11T3 indexable inserts, 90° cutting angle (Teknik Makina) The Corner Turning Head T254TM is a compact indexable insert holder engineered for precise 90° corner turning and shoulder operations, designed to accept APMT 11T3 inserts for workshop and production use 90° cutting angle for precise corner turning Compatible with APMT 11T3 indexable inserts 22 mm tool shank diameter for rigid clamping Supplied with M2.5×5.5 Torx screw T8 Consistent corner geometry for accurate finishing The toolhead provides a 90° cutting angle that ensures repeatable corner profiles and tight shoulder runs. By using standard APMT 11T3 inserts, often supplied by Korloy, the holder simplifies insert sourcing and reduces inventory complexity. The geometry is optimised to produce consistent surface quality on shoulder faces and internal corners, which results in fewer secondary operations and a more efficient production flow. Rigid mounting and quick insert changes to cut downtime With a 22 mm shank for secure clamping and a compact overall length of 40 mm, the assembly offers high stiffness that reduces vibration and improves tool life. The insert is retained with an M2.5×5.5 Torx screw (Torx key T8) for fast, toolroom-friendly changes. The relatively low mass of 0.483 kg aids manoeuvrability during setup while still providing the stability required for repeatable turning cycles. Versatility across workshop turning tasks Designed for APMT 11T3 indexable inserts, the head supports multi-edge insert strategies and is suitable for finishing and semi-finishing of shoulders and radii where precise right-angle control is required. The 63 mm head diameter contributes to rigid contact with the toolholder assembly, and the configuration with seven cutting edges offers options for economical insert indexing in batch production. These characteristics make the head a practical choice where throughput and predictable results are priorities. For secure supply and expert advice on integrating the T254TM corner head into production, contact Metav Werkzeuge—call +49 2822 7131930 or email info@metav-werkzeuge.com for ordering and technical consultancy. Technical data Article number: T254TM Name: Corner turning head for APMT 11T3 Manufacturer: Teknik Makina Dimensions & weight Diameter: 63 mm Shank diameter: 22 mm Overall length: 40 mm Weight: 0.483 kg Cutting angle: 90° Compatibility & fittings For APMT 11T3 indexable inserts Suitable insert maker: Korloy Torx screw: M2.5×5.5 Torx key: T8 Number of cutting edges: 7 FAQ Which inserts fit this turning head? The head is designed for APMT 11T3 indexable inserts; Korloy-compatible APMT 11T3 grades and geometries are suitable for routine use. What shank size is required in the toolholder? A 22 mm shank diameter is specified for rigid mounting and optimal stability when machining with the T254TM. How is the insert secured and changed? Inserts are retained with an M2.5×5.5 Torx screw; use a T8 Torx key for secure fastening and rapid replacement. Is the head suitable for finishing shoulders and corners? Yes — the 90° cutting angle and rigid construction are tailored to produce precise shoulder faces and corner radii with consistent surface finish. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the precise combination of reliable cooling and robust clamping offered by this corner turning head: the integrated internal coolant and compatibility with BOMT 1304 indexable inserts reduce tool change frequency and improve surface finish, while supply from Metav Werkzeuge ensures dependable delivery and technical support. Corner turning head T967-1TM for BOMT 1304 indexable inserts — 63 mm, internal coolant (Teknik Makina) Corner turning head T967-1TM is a compact turning head designed for perpendicular cutting tasks on lathes and toolholders, intended to accept BOMT 1304 indexable inserts. 63 mm head diameter Internal coolant supply Compatible with BOMT 1304 inserts 90° cutting angle, six cutting edges Controlled cooling for longer insert life The integrated internal coolant channel delivers coolant directly to the cutting zone, which improves chip evacuation and reduces thermal load on the insert. For repetitive or long cycle turning operations this means longer tool life and more consistent surface finishes. Using coolant at the tip also helps avoid thermal expansion of the tool head, maintaining dimensional stability during extended runs. The coolant routing is especially beneficial when machining alloys or tougher materials where heat build-up is a limiting factor. Stable geometry for accurate shoulder and facing cuts With a 63 mm head diameter and a defined 90° cutting angle, the design provides a stable cutting geometry ideal for square shoulders and facing operations. The head offers six cutting edges, allowing multiple indexings of the insert before replacement, which enhances cost-efficiency in production environments. The compact 40 mm overall length contributes to reduced overhang and improved rigidity in the toolholder, translating directly into better repeatability and tighter tolerances on machined components. Service‑friendly fastening and precise assembly Fastening utilises a T10 Torx interface and M3.5x8.5 Torx screw for secure clamping of each insert pocket, ensuring straightforward replacement and minimising downtime. The Torx standard gives positive drive engagement to prevent stripping during tightening and allows controlled torque application for reliable repeatability. Clear access to screws and standardised fasteners means maintenance is faster and less prone to error, supporting higher uptime on the shop floor. Built for compatible systems and production workflows This tool head is configured specifically for BOMT 1304 indexable inserts and is compatible with inserts from Ingersoll, making it easy to integrate into existing tooling systems that already use that insert family. At a weight of 0.612 kg, it balances robustness with manageable mass for multi‑station turrets and automated tool changers. The combination of standardised mounting, coolant capability and insert compatibility supports both small workshops and industrial production lines seeking predictable, repeatable cutting performance. For tailored advice on integrating the Teknik Cutting Tools corner turning head T967-1TM into existing toolholders or for guidance on optimal coolant settings and insert choice, contact Metav Werkzeuge — reliable supply and technical assistance from Emmerich is available via email or phone. Technical data Article number / SKU: T967-1TM Product type: Corner turning head eClass: 21181015 Core measurements Head diameter: 63 mm Overall length: 40 mm Weight: 0.612 kg Cutting angle: 90° Cutting edges: 6 Special features Internal coolant Compatible inserts: BOMT 1304 (Ingersoll) Torx key: T10 Torx screw: M3.5x8.5 FAQ What inserts does this turning head accept? The turning head accepts BOMT 1304 indexable inserts; it is also compatible with inserts from Ingersoll, ensuring straightforward integration into established tooling systems. Is the coolant supplied through the head? Yes, the head features internal coolant routing that delivers cooling directly to the cutting zone to improve chip control and extend insert life. How many times can an insert be indexed? The head is designed for inserts with six cutting edges, allowing multiple indexings before replacement, which reduces tooling costs over time. Which fasteners are used for securing the inserts? Inserts are secured with a T10 Torx drive using M3.5x8.5 Torx screws, providing positive engagement and reliable clamping during machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, sturdy toolholder that combines a 22 mm shank and a 90° cutting angle for consistent corner operations; the holder accepts WNMU 0705 indexable inserts and secures them with an M4x10 Torx screw. Order the corner insert head directly via Metav Werkzeuge or ask our consultants if needed. Teknik Makina corner insert head — for WNMU 0705 indexable inserts, 22 mm shank The Teknik Makina corner insert head is a compact toolholder engineered for machining tasks that require reliable indexable-insert performance and a controlled 90° cutting geometry. 22 mm shank diameter for stable clamping Compatible with WNMU 0705 indexable inserts 90° cutting angle for precise corner machining M4x10 Torx screw, T15 key for secure fastening High-stability design for predictable results The holder’s 22 mm shank and 63 mm diameter body provide a rigid interface with the machine, reducing vibration and improving surface finish in sensitive operations. Combined with the 90° cutting angle, the arrangement delivers a defined cutting geometry that simplifies process planning and toolpath definition. This mechanical stability translates into repeatable part quality and fewer in-process adjustments, which supports higher throughput without compromising dimensional accuracy. Fast, secure insert mounting to reduce downtime Designed for use with WNMU 0705 indexable inserts from brands such as ISCAR, the head uses an M4x10 Torx screw tightened with a T15 key for positive, repeatable clamping. The simple fastening method shortens tool-change intervals and lowers set-up complexity on the shopfloor. At an overall length of 40 mm and a mass of 0.515 kg, the holder balances compact installation with enough mass to dampen chatter, offering a practical compromise between accessibility and cutting stability. Practical application and maintenance advantages Equipped with six cutting edges, the insert system enables multiple indexing steps before replacement, improving cost efficiency per edge. The compact footprint suits confined tool stations or multi-tool turrets while the robust construction reduces the need for frequent maintenance. Routine checks are limited to screw torque and insert condition; this straightforward upkeep supports long production runs and predictable tooling budgets. The combination of mechanical clarity and uncomplicated serviceability makes the head suitable for both specialised workshops and industrial turning cells. Contact Metav Werkzeuge today to discuss application fitment or request further technical details for the Teknik Makina corner insert head T393TM Technical Data Article number: T393TM Manufacturer: Teknik Makina Weight: 0.515 kg Overall length: 40 mm Shank diameter: 22 mm Diameter: 63 mm Facts Cutting angle: 90° Number of cutting edges: 6 Fastening screw: M4x10 Torx key: T15 Special features Compatible inserts: WNMU 0705 Compatible insert manufacturer: ISCAR Compact toolholder design Indexable-insert system FAQ Can this holder be used with WNMU 0705 inserts from other manufacturers? The corner insert head accepts WNMU 0705 indexable inserts; compatibility with other brands depends on the exact insert geometry, but the holder is specified for WNMU 0705 profiles and is confirmed with ISCAR variants for the best fit. What tools are required to mount and secure the insert? Mounting uses an M4x10 Torx screw tightened with a T15 key; the process is quick and repeatable for the Teknik Makina corner insert head (SKU T393TM). How does the 22 mm shank influence machining performance? The 22 mm shank provides a stable clamping interface that reduces vibration and enhances surface finish, leading to more consistent machining results and longer insert life. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the precise 90° cutting geometry, compact 63 mm diameter and integrated internal coolant for reliable shoulder turning and reduced cycle times; order or request advice via Metav Werkzeuge for a seamless supply from Emmerich. 63 mm Corner Turning Head for ANKX 1205 Indexable Inserts — 90° Cutting Angle (Teknik Makina) A 63 mm corner turning head designed for ANKX 1205 indexable inserts, delivering 90° cutting geometry and internal coolant for efficient shoulder and face turning in compact setups 63 mm diameter for compact setups 90° cutting angle for precise shoulder turning Internal coolant for improved chip evacuation Compatible with ISCAR ANKX 1205 inserts Maximise machining precision and process stability The compact turning head combines a 63 mm diameter with a short overall length (45 mm) to reduce overhang and minimise deflection in tight setups. Its 90° cutting angle is tailored for accurate shoulder and face machining, enabling consistent dimensional control and repeatability. Designed for indexable-insert turning, the head accepts ANKX 1205 inserts from ISCAR, which simplifies inventory management and shortens tool-change times. The measured mass of 0.596 kg supports dynamic stability while maintaining a rigid connection to the toolholder. Internal coolant and secure insert clamping for longer tool life Built-in internal coolant channels direct cutting fluid close to the cutting edge, improving lubrication and chip control under medium to heavy cuts. This targeted cooling reduces thermal loads on the insert, which in turn extends life and maintains surface quality. Inserts are fastened with M4x10 Torx screws, driven with a T15 key for repeatable torque and clamping force; this secure fixation minimises micro-movements that can cause premature wear and chatter. Compact design for quick set-up and reliable indexing With an overall length of 45 mm and a weight of 0.596 kg, the turning head is engineered for short overhang applications where stiffness matters. It provides six effective cutting positions, enabling efficient index changes without complex regrinding. The robust mechanical interface and standardised screw sizes simplify maintenance and shorten downtime during insert changes, translating to higher machine availability and predictable throughput. Suitable applications and workshop benefits The head is intended for general turning operations where precise 90° shoulders, faces and chamfers are required. It suits production shops and subcontractors working with steel and alloy components where interchangeability with ISCAR ANKX 1205 inserts is a logistical advantage. The compact footprint supports multi-spindle and bar-fed machines, while the internal coolant option enhances performance on medium-cut cycles. For further specification checks or to confirm compatibility with existing toolholders, technical guidance is available from Metav Werkzeuge. Contact Metav Werkzeuge for tailored advice on application-specific setup and to secure the Teknik Cutting Tools corner turning head with internal coolant — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: T574-1TM Label: 63 mm corner turning head ANKX 1205 L45 mm with internal coolant Manufacturer: Teknik Makina Facts Diameter: 63 mm Overall length: 45 mm Weight: 0.596 kg Cutting angle: 90° Cutting positions: 6 Design & special features Internal coolant: yes Suitable for: ANKX 1205 indexable inserts Compatible insert manufacturer: ISCAR Torx screw: M4x10 Torx key: T15 FAQ What insert type does this head accept? The head is designed for ANKX 1205 indexable inserts (compatible with ISCAR insert variants) and secures them with M4x10 Torx screws. Is internal coolant available and how does it help? Yes; the internal coolant directs fluid to the cutting edge, improving chip evacuation, reducing tool temperature and extending insert life. What are the main dimensional limits for use in compact setups? With a 63 mm diameter and 45 mm overall length, the head is suited to applications requiring low overhang and high stiffness. How many effective cutting positions are provided? The head provides six cutting positions, enabling quick indexing and extended intervals between insert replacements. Which torque tool is required for insert changes? Insert screws use a T15 Torx drive (M4x10 screws) for secure and repeatable clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com