Gibt es einen Hahn und Kolb Online Shop?

Take advantage of a robust left‑hand clamping solution that combines precise insert compatibility and a rigid 93° cutting geometry for dependable turning performance; order directly via Metav Werkzeuge or consult Metav’s specialists for configuration advice. Klemmhalter PDJN for DNMG Indexable Inserts — left‑hand tool holder with PDJNL 2525 ISO designation by Teknik Makina Klemmhalter PDJN for DNMG Indexable Inserts is a left‑hand turning holder designed for facing and light turning operations with DNMG‑format inserts, delivering stable clamping and consistent cutter alignment for industrial workshops. Left‑hand orientation for facing operations For DNMG 1506 indexable inserts ISO PDJNL 2525 designation 150 mm overall length for deep reach Precise clamping for reliable turning results The holder is engineered to secure DNMG 1506 inserts with repeatable accuracy, reducing chatter and rework in batch production. Its PDJNL 2525 mounting geometry ensures consistent seat contact and predictable rake orientation, which translates into steady cutting forces and extended insert life. The left‑hand configuration and the 93° cutting angle combine to keep tool engagement stable on shoulder and face cuts, helping shops hit tolerances more reliably while maintaining throughput. Geometry and fastening that speed up setup times A compact head width of 32 mm and a holder width of 25 mm deliver a low‑profile design that facilitates access in confined setups and multi‑station lathes. The clamping arrangement, specified with an M15 screw interface for the tool‑post mounting, allows secure fixation with minimal torque variation, so changeovers are quicker and tool runout remains low. These aspects reduce setup time and increase uptime, supporting lean production without compromising rigidity. Built for practical reach and balanced handling With an overall length of 150 mm and a cutting height of 38 mm, this holder provides the reach necessary for recessed shoulders while retaining a compact centre of gravity; the result is improved handling during manual set‑up and reduced vibration during turning cycles. The component mass of 0.73 kg contributes to a stable assembly that limits deflection when machining medium to light steel workpieces, helping maintain surface finish and dimensional consistency in series work. A dependable option for systematic workshop workflows Chosen as part of a coordinated tooling system, the PDJN clamping solution supports standardised insert use and straightforward inventory management. The combination of an established ISO designation and a clear material of application for DNMG 1506 inserts simplifies procurement and training, while the left‑hand orientation expands capability for asymmetric machining tasks. This makes the holder a practical addition for workshops aiming to harmonise tooling across multiple machines and operators. For robust left‑hand turning applications, specify the PDJNL 2525 holder from Teknik Makina via Metav Werkzeuge — Metav’s specialists can advise on matching inserts and mounting options to suit the production task. Technical Data Article number: P124TM Manufacturer: Teknik Makina Designation (EN): PDJN for DNMG Indexable Inserts ISO designation: PDJNL 2525 ECLASS: 21181004 Numbers / Core technical data Overall length: 150 mm Cutting head width: 32 mm Holder width: 25 mm Holder height: 25 mm Cutting height: 38 mm Weight: 0.73 kg Cutting angle: 93° Designs / Special features For DNMG 1506 indexable inserts Left‑hand cutting orientation Shank / mounting designation: M15 Suited for industrial turning and facing operations FAQ What inserts fit this holder? The Klemmhalter PDJN for DNMG Indexable Inserts is designed specifically for DNMG 1506 format inserts and provides the correct seat geometry for secure indexing and repeatable positioning. Is the holder suitable for heavy roughing cuts? The PDJN holder by Teknik Makina offers a rigid 93° cutting geometry and a solid clamping design, which is suited for medium to light turning operations; for heavy roughing, selection should be matched to machine stiffness and insert grade. Which side does the holder cut from? This variant is configured for left‑hand cutting, intended for operations where tool engagement is required from the workpiece’s left side relative to spindle rotation. What mounting or shank designation is used? The tool holder is specified with an M15 mounting designation, enabling compatibility with appropriate tool posts and adaptors in standard lathe setups. How does the overall length affect machining access? An overall length of 150 mm provides extended reach for recessed features and shoulders while maintaining control over deflection and vibration for typical workshop tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise insert compatibility, a stable 25 x 25 mm shank and a compact 150 mm overall length for reliable turning operations; order directly via Metav Werkzeuge or consult the team for application advice. SDJCR 2525 clamping toolholder – SDJC for DCMT indexable inserts (right-hand) The SDJCR 2525 clamping toolholder is a right-hand turning holder designed to accept DCMT 11T3 indexable inserts for medium-duty external turning and facing tasks in general workshop and production environments. Compatible with DCMT 11T3 indexable inserts Right-hand cutting orientation Robust 25 x 25 mm shank 150 mm overall length for extended reach Consistent chip control and repeatable geometry for efficient turning The holder is engineered to secure DCMT 11T3 inserts with a stable clamping interface, which reduces micro-movement and improves surface finish on serial components. The 93° cutting angle provides a balanced approach between clearance and cutting force, helping to maintain tool life under typical machining feeds. In practice, a dependable clamping design lowers rework rates by limiting insert chatter, and the result is a more predictable process that supports tighter tolerances on turned parts. Rigid shank and compact length to increase stability and access A 25 x 25 mm shank combined with a 150 mm overall length gives a sturdy yet compact footprint for lathe setups where access and rigidity matter. The moderate mass of 0.735 kg contributes to vibration damping without making tool changes cumbersome. The 32 mm cutting head width and 30 mm cutting height are matched to the insert geometry so cutting forces are transferred evenly into the holder; this reduces edge wear on inserts and allows consistent finishing passes with fewer tool adjustments. Fast mounting and straightforward integration with standard toolposts The turning holder includes an M11 mounting characteristic for straightforward attachment where compatible posts or adapters are used, and the SDJC clamping concept allows quick insert indexing and replacement. For production environments, reduced downtime during insert changes and the use of standard DCMT 11T3 sizes mean less inventory complexity and faster cycle recovery. The combination of standard interface and robust construction supports reliable throughput and simplifies tooling management on the shopfloor. For supply and technical guidance on Teknik Cutting Tools' SDJCR 2525 clamping toolholder, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to discuss compatibility with specific lathes and insert grades Technical Data Article number: D228TM Manufacturer: Teknik Makina ISO designation: SDJCR 2525 ECLASS: 21181004 Data Shank width: 25 mm Shank height: 25 mm Overall length: 150 mm Cutting head width: 32 mm Cutting height: 30 mm Cutting angle: 93° Weight: 0.735 kg Suitable for inserts: DCMT 11T3 Mounting thread: M11 Cutting direction: right Special features SDJC clamping concept for DCMT inserts Right-hand turning configuration Compact, rigid construction for reduced vibration FAQ Which insert size fits this holder? The SDJCR 2525 clamping toolholder accepts DCMT 11T3 indexable inserts as the standard size for its clamping pocket. Is the holder suitable for right-hand turning only? Yes, the holder is configured for a right-hand cutting direction and is intended for external turning and facing in that orientation. What are the shank dimensions and overall length? The holder features a 25 x 25 mm shank and an overall length of 150 mm, providing a compact but rigid setup for many lathe toolposts. How does the SDJC clamping system affect tool change time? The SDJC clamping design allows quick indexing and secure retention of inserts, which reduces changeover time and supports higher machine uptime. Can this holder be mounted to standard toolposts? The holder uses an M11 interface characteristic and is compatible with standard mounting arrangements where that thread or corresponding adapter is accepted. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise clamping, integrated internal coolant and proven compatibility with VBMT 1604 inserts for reliable turning operations; order via Metav Werkzeuge or consult our specialists for application advice. SVJBL 2020 clamping toolholder — Left‑hand turning holder with internal coolant by Teknik Makina The SVJBL 2020 clamping toolholder is a left‑hand turning holder designed for VBMT 1604 indexable inserts, offering through‑coolant capability for improved chip control and tool life. Left‑hand holder for VBMT 1604 inserts Integrated internal coolant channel 93° cutting angle for versatile turning 150 mm overall length for extended reach Improved cycle times through secure clamping and coolant supply The holder combines a robust clamping design with an integrated internal coolant channel, reducing setup time and improving cutting stability. The secure clamp interface minimises insert movement under load, which translates into consistent surface finish and fewer rework cycles. With the coolant routed directly to the cutting zone, chip evacuation and thermal control are enhanced — a practical advantage when machining alloys or longer workpieces where temperature and chip control influence part quality. Versatility in turning applications with standard insert compatibility Engineered for VBMT 1604 indexable inserts, the toolholder supports a wide range of carbide grades and chipbreaker geometries, enabling flexible process selection for finishing and semi‑roughing. The 93° cutting angle delivers a favourable approach for general‑purpose external turning, while the left‑hand orientation caters to specific machine setups and toolpath strategies. Compatibility with a standard shank designation (M16‑IK) and the supplied top plate reference (TA034) simplifies integration into existing tool assemblies. Practical assembly and service features that reduce downtime Designed for straightforward mounting and service, the assembly uses an M3.5x11 Torx screw and a T15 Torx key for clamping plate retention, enabling quick insert changes and secure fastening. The holder’s 150 mm overall length and compact head dimensions (head width 32 mm, body width 25 mm, height 25 mm) balance accessibility and stiffness, which is especially useful on lathes where reach and rigidity must be optimised. The modest mass of approximately 0.683 kg keeps tool overhang manageable while maintaining stability during cuts. Contact Metav Werkzeuge for detailed application guidance and to discuss suitability of the Teknik Cutting Tools SVJBL 2020 clamping toolholder for specific turning tasks — Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany; eMail: info@metav-werkzeuge.com; Tel: +49 2822 7131930 Technical data Article number: AP555TM Manufacturer: Teknik Makina ISO designation: SVJBL 2020 Intended inserts: VBMT 1604 Shank designation: M16‑IK Facts Overall length: 150 mm Holder height: 25 mm Head width: 32 mm Body width: 25 mm Cutting height: 40 mm Cutting angle: 93° Weight: 0.683 kg Special features Left‑hand orientation Internal coolant (through‑coolant) Top plate reference: TA034 Fastening: Torx screw M3.5x11 Required Torx key: T15 FAQ What inserts fit this holder? The SVJBL 2020 clamping toolholder is specified for VBMT 1604 indexable inserts and accepts standard VBMT geometries used in turning. Is the coolant internal or external? This holder provides internal (through) coolant, directing cutting fluid to the insert‑nose area for improved chip control and tool life. Which shank or boring bar designation is required? The toolholder is designed for a M16‑IK bar or bore stem, as indicated by the provided shank designation. Can the holder be used for finishing and roughing operations? Yes. With appropriate carbide grades and chipbreakers in VBMT 1604 inserts, the holder suits both finishing and semi‑roughing applications thanks to its secure clamp and 93° approach. What fastening parts are needed for maintenance? Replacement or service requires the M3.5x11 Torx screw and a T15 Torx key for top plate and clamp operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, right‑hand turning toolholder that combines ISO SVJCR 2525 compatibility with a 150 mm overall length for improved rigidity and straightforward insert replacement; order the part directly via Metav Werkzeuge or contact our consultants for application advice. Toolholder SVJCR 2525 – SVJC for VCMT Indexable Inserts (Teknik Makina) — Right‑hand turning, 150 mm overall length The SVJC for VCMT Indexable Inserts is a right‑hand turning toolholder engineered for secure clamping of VCMT 1604 inserts in standard external turning applications. *SVJCR 2525 ISO designation for standardised fit *Compatible with VCMT 1604 indexable inserts *Right‑hand turning with 150 mm overall length *Robust head: 32 mm width, 25 mm height Reliable clamping for consistent machining results The holder is designed around the SVJCR 2525 ISO interface and secures VCMT 1604 indexable inserts with a conventional clamping screw configuration, ensuring repeatability across multiple tool changes. The integrated M16 bore fastens the insert seat reliably, which reduces setup variation and minimises rework caused by inconsistent positioning. This results in shorter machine downtime and more predictable process outputs, making the component suitable for production lines where repeatable turning accuracy matters. Dimensions that increase rigidity and extend cutter life With an overall length of 150 mm and a toolhead measuring 32 mm wide by 25 mm high, the holder provides a stable platform that limits vibration during external turning. The specified cutting height of 40 mm and a cutting angle 93° contribute to optimal chip flow and controlled engagement for medium‑duty operations. The assembly weighs approximately 0.683 kg, a balance that supports steady clamping while remaining easy to handle during setup. The mechanical geometry is aimed at improving tool life by maintaining stable cutting conditions rather than relying on compensatory machining parameters. Simple integration and production readiness Configured for right‑hand operation, the toolholder integrates into conventional turret and toolpost setups and is a direct option where SVJCR holders are already standardised. Compatibility with the widespread VCMT insert family simplifies inventory and spares management, while the ISO designation supports rapid replacement without the need for special adaptors. For procurement, Metav Werkzeuge acts as a European quality filter and supply partner, offering consistent availability from stock and technical guidance for workshop integration. For purchase enquiries or detailed application guidance regarding the SVJCR 2525 toolholder, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — consultants are available to advise on fitment and machining set‑up. Technical Data Article number: D248TM Manufacturer: Teknik Makina Designation: SVJCR 2525 Product name: SVJC for VCMT Indexable Inserts Suitable inserts: VCMT 1604 Cutting direction: right Dimensions & Weights Overall length: 150 mm Head width: 32 mm Holder width: 25 mm Cutting height: 40 mm Weight: 0.683 kg Cutting angle: 93° Features & Compatibility M16 clamping bore ISO interface: SVJCR 2525 Compatible with VCMT 1604 indexable inserts Right‑hand turning orientation Designed for external turning applications FAQ Which inserts fit this toolholder? The SVJC for VCMT Indexable Inserts accepts VCMT 1604 indexable inserts and is designed for standard insert seating and clamping. Is the holder for right‑hand or left‑hand turning? This toolholder is configured for right‑hand turning operations. What is the ISO designation of the tool shank? The shank is specified as SVJCR 2525, matching common ISO toolholder standards. What are the key dimensions to check for machine compatibility? Key dimensions are an overall length of 150 mm, head width 32 mm, holder width 25 mm, and cutting height 40 mm. How is the insert secured to the holder? Clamping is achieved via the M16 bore and standard clamping hardware, providing secure seating for VCMT 1604 inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust, right‑hand toolholder that combines a 95° cutting angle with proven compatibility for CN-- 1906 indexable inserts, ensuring secure clamping and reproducible turning results; order directly via Metav Werkzeuge or request consultation from our specialists. Toolholder DCLN (DCLNR 2525) — right‑hand turning holder for CN-- inserts by Teknik Makina A Toolholder DCLN designed for right‑hand turning operations with CN-- indexable inserts, optimised for medium‑duty workshop and production turning tasks. Right‑hand turning holder DCLN Compatible with CN-- 1906 inserts 95° cutting angle for secure cutting 150 mm overall length, robust 0.82 kg Precision and stability for consistent turning performance The DCLN toolholder delivers stable chip control and reliable insert clamping through its 95° cutting angle, which reduces radial loads and helps maintain tool life. Its ISO designation DCLNR 2525 denotes a standardised shank geometry for predictable setup and repeatable positioning in the toolpost. For production environments where process stability matters, the holder’s dimensions and mass contribute to reduced vibration during turning, resulting in improved surface finish and consistent part tolerances. Fast setup and wide insert compatibility to save machine time Designed to accept CN-- 1906 indexable inserts, the holder simplifies insert changes and shortens setup cycles. The M19 bore designation and clear shank dimensions assist with secure mounting and alignment in common toolpost systems. With a cutting height of 40 mm and compact head width, this solution allows quick access to the insert seat and straightforward clamping, limiting downtime and enabling efficient changeovers between operations. Workshop durability and clear technical fit for everyday use Constructed for routine workshop demands, the holder’s 150 mm overall length and 0.82 kg weight offer a balance between reach and rigidity. The head width of 32 mm and shank width of 25 mm make the unit suitable for a broad range of turning tasks while keeping the tool overhang moderate. The right‑hand orientation and defined geometry support predictable chip flow and a secure interface with standard indexable turning plates, helping maintain throughput without frequent adjustments. Contact Metav Werkzeuge for personalised advice on the Teknik Makina DCLN toolholder (SKU D163TM); technical data and application guidance are available by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: D163TM Manufacturer: Teknik Makina Designation: DCLN for CN-- Indexable Inserts ISO designation: DCLNR 2525 Cutting direction: right Facts Shank height: 25 mm Head width: 32 mm Shank width: 25 mm Cutting height: 40 mm Overall length: 150 mm Weight: 0.82 kg Cutting angle: 95° Special features Compatible inserts: CN-- 1906 Bore designation: M19 Right‑hand turning holder Standardised ISO shank geometry FAQ Which inserts fit this holder? The holder accepts CN-- 1906 indexable inserts; the DCLN design ensures proper seating and secure clamping for these plates. What is the cutting direction of the toolholder? This toolholder is specified for right‑hand turning operations and is manufactured to suit conventional right‑hand tool setups. What are the key dimensions to check for machine compatibility? Important dimensions include the 25 mm shank height, 32 mm head width, 150 mm overall length and the 40 mm cutting height; verify these against the machine’s toolpost and clearance requirements. Is the DCLN suitable for production use? Yes. The holder’s standardised geometry and robust mass provide stability for routine workshop and small‑series production tasks where reproducible results are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining secure clamping for CCMT 1204 inserts with internal coolant and a stable 95° cutting angle, this holder delivers consistent right‑hand turning and reduced vibration. Benefit from the compact 150 mm overall length and straightforward Torx fixation for fast insert changes; order direct through Metav Werkzeuge or consult our specialists for precise implementation. SCLC for CCMT indexable inserts – SCLCR 2525 clamping holder (right‑hand, internal coolant) by Teknik Makina A SCLC for CCMT indexable inserts clamping holder engineered for right‑hand turning operations, offering internal coolant delivery and robust ISO SCLCR 2525 compatibility for medium‑duty lathe work Right‑hand cutting orientation Internal coolant for controlled flow Compatible with CCMT 1204 inserts ISO SCLCR 2525 toolholder design Accuracy and insert compatibility for reliable turning results The holder is designed around the CCMT 1204 insert family and the SCLCR 2525 ISO form, which together provide a reproducible insert seat and predictable cutting line. The slightly negative 95° cutting angle reduces radial load peaks and helps keep the workpiece concentric during finishing passes. For production contexts where repeatability matters, this configuration supports stable surface quality and consistent dimensional outcomes, reducing scrap rates and machine idle time. Robust clamping and quick serviceability to cut setup times A compact head width of 32 mm and a secure clamping geometry deliver repeatable seating and low vibration. The clamp is fastened with a Torx screw M4x11, operated with a T15 key, while the matching U‑plate is identified as TA015‑1 for straightforward replacement. With an overall length of 150 mm and a weight of 0.771 kg, the assembly balances rigidity and handling ease, so countertop setup is faster and tool swaps are less disruptive to cycle times. Coolant integration and operational advantages on the lathe Integrated internal coolant channels feed the insert area directly, improving chip evacuation and helping to manage cutting temperatures without external modification. The holder accepts a conventional M12‑IK bore interface for secure mounting and is optimised for right‑hand cutting direction in typical turning cycles. Together, these technical choices contribute to longer insert life and more consistent performance during extended production runs, while the compact form supports close‑quarters tool layouts on the turret. For practical purchasing or application advice regarding this Teknik Makina SCLC clamping holder (SKU AP503TM), contact Metav Werkzeuge for technical clarification or to arrange a supply — telephone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical Data Article number: AP503TM Manufacturer: Teknik Makina Type: SCLC for CCMT Indexable Inserts (SCLCR 2525) Brand: Teknik Makina Cutting direction: right Internal coolant: yes Dimensions & weight Overall length: 150 mm Head width: 32 mm Holder width: 25 mm Holder height: 25 mm Cutting height: 30 mm Weight: 0.771 kg Cutting angle: 95° Design & special features Compatible inserts: CCMT 1204 Fastening screw: M4x11 (Torx) Torx key size: T15 U‑plate: TA015‑1 Tool shank / bore designation: M12‑IK ISO designation: SCLCR 2525 FAQ What inserts fit this clamping holder? The holder is specified for CCMT 1204 indexable inserts; the SCLCR 2525 seating ensures correct positioning and chip control. Is the coolant internal or external? The toolholder features internal coolant, supplying fluid directly to the insert zone to aid chip evacuation and temperature control. Which cutting direction is intended for this toolholder? This design is for right‑hand turning operations, with geometry optimised for stable right‑hand cuts. What fastener and key are required for insert clamping? Clamping uses a Torx screw M4x11, tightened with a T15 key for secure and repeatable fixation. Can this holder be mounted on standard tool posts? The holder uses an M12‑IK shank/bore designation for turret mounting; ensure turret compatibility with this standard. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, purpose-built clamping wedge that secures WNMG 06 turning inserts with reliable repeatability and low added mass; combine precision, simple integration and trusted supply from Metav Werkzeuge for uninterrupted workshop operation — order directly via Metav Werkzeuge or consult the team for application advice. Spannpratze — clamping wedge for WNMG 06 inserts by Teknik Makina A Spannpratze engineered as a compact clamping wedge to secure WNMG 06 turning inserts in compatible turning toolholders for workshop and light industrial use Clamping wedge for WNMG 06 inserts Lightweight: approx. 0.1 kg Designed for turning toolholders Consistent clamping for reliable turning performance The clamping wedge provides a straightforward mechanical solution for securing indexable inserts, delivering secure clamping and repeatable positioning that support consistent cutting performance. By focusing on a simple wedge principle, the component offers a predictable clamping force that helps maintain insert alignment during turning operations. The design reduces variables in the tool assembly and supports process stability, which is particularly valuable in production runs where reproducible results matter. Compatibility with WNMG 06 geometry ensures the device interfaces with a widely used insert form, easing part selection and spare‑part management. Compact design that simplifies workshop workflows A compact component with a lightweight profile, the wedge is intended for easy handling and rapid replacement at the bench. Reduced mass contributes to simpler tool balancing and minimises the impact on the holder assembly, while the compact footprint aids installation in confined toolholder envelopes. For workshop teams, this translates into quicker change‑overs and fewer interruptions. Clear physical form and standard mounting dimensions make inventory and storage straightforward, supporting efficient stock rotation and rapid availability of spares for routine maintenance. Robust integration and practical benefits for procurement Specified by a recognised manufacturer, the component is suited to standard turning setups requiring WNMG 06 inserts and fosters interoperability across common toolholder systems. Selecting such a dedicated clamping element helps streamline procurement and reduces the need for custom solutions, thereby shortening lead times and simplifying supplier lists. The practical nature of the part lends itself to predictable service life when used within normal operating parameters, contributing to dependable workshop throughput and lower administrative effort in parts management. Contact Metav Werkzeuge to check compatibility with existing holders and secure Teknik Makina clamping wedges for WNMG 06 applications — assistance and order processing available from Metav Werkzeuge in Emmerich by phone or email. Technical Information Article number: BK019TM Manufacturer: Teknik Makina Core data Weight: 0.1 kg eClass: 21189290 Design & compatibility Suitable for WNMG 06 inserts Product name: Spannpratze UID: BK019TM FAQ What is this component used for? The Spannpratze by Teknik Makina is used as a clamping wedge to secure WNMG 06 turning inserts in compatible toolholders, ensuring repeatable positioning during turning operations. Is the clamping wedge suitable for all WNMG 06 toolholders? Compatibility depends on the toolholder design; the Spannpratze is designed for standard WNMG 06 insert geometries, but verification against the specific holder dimensions is recommended before installation. How much does the component weigh and why does that matter? The clamping wedge weighs approximately 0.1 kg; the lightweight design reduces added mass to the tool assembly, which aids handling and minimises changes to holder balance. Are any special maintenance steps required? Routine inspection for wear, cleanliness of the clamping surfaces and correct torqueing of fastening elements will help maintain clamping reliability; replace the wedge if deformation or surface damage is detected. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise clamping, compact dimensions and quick assembly for consistent external-threading results in batch and single-part production. Order the component directly via Metav Werkzeuge or contact our consultants for specification checks. SER 1212 clamping holder (D498TM) – right-hand external threading, compact 12 × 12 mm cross-section The SER 1212 clamping holder is a right-hand tool holder designed for external threading on lathes and turning centres, providing a compact, rigid solution for short overhang and repeatable thread profiles. SER 1212 clamping holder for external threads Right-hand cutting direction Compatible with ER11 inserts and M11-ER11 shank Compact 12 × 12 mm cross-section Precision and stability for repeatable thread quality The compact 12 × 12 mm cross-section and a cutting height of 20 mm deliver a rigid seating that minimises vibration during turning, which improves surface finish and thread accuracy. The tool body design keeps the insert firmly clamped, translating into consistent thread form across production runs. This rigidity is especially relevant where repeatability matters, such as batch threading of shafts or pins, because reduced chatter leads to fewer rejects and less rework. Fast setup and secure clamping reduce downtime Compatibility with standard ER11 turning inserts and the M11-ER11 shank designation means the holder integrates cleanly with common boring-bar systems. Assembly relies on a Torx fixing (key T8) and a securing screw (M2.5×5.5), allowing fast, repeatable changeovers with minimal adjustment. The ISO designation SER 1212 signals an established form factor that fits industry workflows, so tool change procedures remain lean and reliable in a production environment. Compact overall length and light handling for flexible use With an overall length of 150 mm and a net weight of 0.193 kg, the holder balances accessibility and control: long enough for typical setups but short enough to keep overhang low for improved rigidity. The right-hand cutting direction supports conventional thread turning operations without altering feed strategy. Designed by Teknik Makina, this tool holder suits both demanding shop-floor use and smaller workshops seeking industrial‑grade clamping performance with compact dimensions. Contact Metav Werkzeuge today to discuss the Teknik Makina SER 1212 clamping holder and confirm suitability for specific threading tasks or to arrange prompt delivery from our Emmerich hub. Technical data Article number: D498TM Manufacturer: Teknik Makina ISO designation: SER 1212 Description: clamping holder for outside thread, right-hand Facts Cross-section width: 12 mm Cross-section height: 12 mm Cutting height: 20 mm Overall length: 150 mm Weight: 0.193 kg Special features Right-hand cutting direction For turning inserts: 11 ER Boring bar / shank designation: M11-ER11 Torx screw: M2.5×5.5 Torx key size: T8 SKU: D498TM FAQ What cutting direction is this holder designed for? The SER 1212 clamping holder is configured for a right-hand cutting direction suitable for standard external-thread turning operations. Which inserts and shank standards are supported? This tool supports 11 ER turning inserts and corresponds to a M11-ER11 shank/boring-bar designation for straightforward integration. What are the key dimensions and weight of the holder? The holder has a 12 × 12 mm cross-section, 20 mm cutting height, overall length 150 mm and weighs 0.193 kg. Which fastening hardware is used for the clamping screw? The clamping screw is M2.5×5.5, tightened with a T8 Torx key for quick, repeatable assembly. Is this holder suitable for production environments? Yes; the SER 1212 clamping holder (Teknik Makina, SKU D498TM) offers compact rigidity and standard interface compatibility, making it suitable for consistent threading across production batches. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of extended reach and stable clamping for efficient turning operations; the compact cross-section and ISO conformity reduce tool changes and simplify inventory. Order directly via Metav Werkzeuge or consult our specialists for application guidance. Clamping holder L150 mm (P095TM) – 150 mm length, 25 x 25 mm cross-section, Teknik Makina A clamping holder L150 mm designed for secure tool mounting in machining applications, offering extended reach and standardised compatibility for workshop tool posts 150 mm overall length for extended reach 25 x 25 mm cross-section for stable clamping ISO 2525 standard shank for compatibility 30° cutting angle for controlled tool engagement Extended reach that reduces setup frequency The 150 mm overall length provides extra reach for components with deeper profiles, enabling fewer workpiece repositionings and a more efficient setup routine. The elongated design balances accessibility with rigidity, so the holder supports stable machining even when access is limited. With a mass of 0.594 kg, the component offers reassuring solidity without excessive weight, contributing to consistent tool behaviour and reduced vibration during cuts. Standardised shank for straightforward tool management Built to the ISO 2525 specification, the holder interfaces cleanly with widely used tool posts and fixtures, reducing the variety of adapters required in the tool crib. The 25 x 25 mm cross-section denotes the clamping envelope, ensuring a tight seat and reliable torque transmission. For purchasers managing stock, this standardisation simplifies procurement and minimises downtime caused by incompatible fittings — a pragmatic advantage for production-focused workshops. Geometry tuned for controlled engagement and durability A 30° cutting angle supports predictable chip formation and steadier tool entry, making the holder suitable for general turning tasks where surface quality and tool life are priorities. The robust construction and attention to machining tolerances translate into a dependable clamping solution for repetitive workflows. Supplied by Teknik Makina, the design aims to balance practical performance with ease of integration into existing setups, reducing the need for frequent adjustments. For dependable supply and tailored advice on Teknik Makina clamping solutions, contact Metav Werkzeuge for ordering and technical consultation at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — Metav Werkzeuge will assist with product selection and delivery to suit workshop needs Technical data Article number: P095TM Label: Klemmhalter L150mm Manufacturer: Teknik Makina Facts Overall length: 150 mm Weight: 0.594 kg Cross-section width: 25 mm Cross-section height: 25 mm Cutting angle: 30° eClass: 21181004 Special features ISO designation: 2525 Product type: Clamping holder Category path: Zerspanen > Klemmhalter UID: P095TM FAQ What machine interfaces is this holder compatible with? The clamping holder L150 mm (P095TM) conforms to ISO 2525, so it is compatible with machine tool posts and fixtures designed for that shank standard. Can the holder be used for deeper turned parts without extra supports? Yes, the 150 mm overall length provides additional reach; however, the stability of each setup should be evaluated and, where necessary, supplementary support or reduced overhang should be considered. How does the 25 x 25 mm cross-section affect performance? A 25 x 25 mm cross-section ensures a secure clamping envelope and good torque transmission, which helps to maintain cutting stability and consistent surface finish during operations. Is the 30° cutting angle suitable for general turning tasks? The 30° engagement angle is designed for controlled entry and predictable chip formation, making the holder well suited to a broad range of general turning applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, ISO‑standard interface and a 150 mm reach to improve turning stability and accessibility in constrained setups; the combination of a 25×25 mm cross section and a 30° approach angle supports consistent cutting results. Order the clamping holder directly via Metav Werkzeuge or request a technical consultation for integration advice. Clamping Holder L150 mm (Toolholder) – 25×25 mm, 30° by Teknik Makina The Clamping Holder L150 mm is a compact toolholder engineered for secure mounting and precise positioning in small to medium turning applications, offering an ISO‑standard interface for straightforward integration. ISO 2525 compatible mounting interface Robust 25×25 mm cross section 150 mm overall length for deep reach 30° cutting angle for universal turning Improved machining stability for consistent results The Clamping Holder L150 mm delivers measurable improvements in repeatability through its rigid 25×25 mm cross section and standardised ISO 2525 interface. These attributes reduce unwanted deflection during cut entry and exit, which in turn contributes to a more uniform surface finish and fewer corrective passes. For operations where part tolerances and cycle reliability matter, the reduced vibration and steady clamping position help to decrease rework and increase first‑pass accuracy, making the holder a sound choice for production and jobbing environments that prioritise process stability. Optimised reach and workshop versatility to increase throughput With an overall length of 150 mm, the toolholder provides extended reach for deeper bores and components with restricted access while maintaining adequate stiffness for routine turning tasks. The 30° approach facilitates favourable cutting engagement for a range of turning strategies, allowing simpler tool set‑ups and faster changeovers when paired with compatible insert systems. Because the holder adheres to a recognised interface standard, retrofitting into existing tool posts is straightforward, reducing machine downtime and supporting leaner workflow in mixed‑batch production. Durable construction, traceability and straightforward procurement The holder’s compact mass (approx. 0.594 kg) and precise form factor support robust day‑to‑day handling without compromising machine balance. Traceability is ensured via the stock reference P092TM, which simplifies ordering and inventory management. Supplied by Teknik Makina and distributed through Metav’s European logistics hub, the component benefits from consistent quality checks and reliable availability. For workshops seeking dependable tooling components that integrate seamlessly into established processes, this toolholder offers a pragmatic combination of durability and standards compliance. Contact Metav Werkzeuge today for a detailed specification match or to secure supply of the Teknik Makina clamping holder P092TM; Metav’s specialists in Emmerich provide prompt technical advice and order handling Technical data Article number: P092TM Label: Clamping Holder L150mm Product type: Clamping holder Facts Overall length: 150 mm Width: 25 mm Height: 25 mm Weight: 0.594 kg Cutting angle: 30° Special features ISO interface: 2525 Manufacturer: Teknik Makina ECLASS: 21181004 FAQ What standard interface does the holder use? The holder features an ISO 2525 interface, allowing straightforward mounting on compatible tool posts and carriers. What are the main dimensions and weight? Key dimensions are 150 mm overall length with a 25×25 mm cross section and a weight of approximately 0.594 kg for the P092TM item. Which machining tasks is this holder suited for? This clamping holder is designed for small to medium turning operations where a compact, stiff toolholder with a 30° approach is advantageous. How can the P092TM be identified for reordering? Reorder using the stock reference P092TM and the label Clamping Holder L150mm; these identifiers ensure traceability through Metav’s catalogue. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of reliable clamping with a 25 mm body and 150 mm overall length for stable turning and consistent chip control; the MTENN design enables quick insert changes and predictable tool performance. Order directly via Metav Werkzeuge or consult our specialists for spacing, compatibility and delivery options. Clamping holder MTENN 2525 – MTENN toolholder for TN-- 1604 indexable inserts, 25 mm body (Teknik Makina) The Clamping holder MTENN 2525 is a robust turning toolholder designed for secure seating of TN-- 1604 indexable inserts in general turning applications, combining compact dimensions with a standard ISO interface for workshop integration 25 mm body diameter for rigid support 150 mm overall length for stable overhang Compatible with TN-- 1604 indexable inserts 60° cutting angle for common turning profiles Consistent rigidity for precision turning A short, rigid clamping body reduces vibration and keeps cutting geometry stable; the 25 mm body width and 150 mm overall length deliver a compact span that improves surface finish and repeatability. The design translates into fewer reworks and steadier cycle times: by limiting deflection the holder supports the insert edge where accuracy matters most. The included 60° cutting angle aligns with common insert grades and turning strategies, making the unit suitable for diverse workshop setups while reducing the need for multiple toolholders. Fast insert changes and straightforward compatibility Designed around the MTENN ISO designation, this toolholder accepts TN-- 1604 indexable inserts and is prepared for routine insert replacement without specialised fixtures. The clamping geometry and M16 shank/interface allow a secure fit and predictable repeatability between changes, which shortens tool-change time and supports lean production. Material and coating details for inserts determine cutting data; pairing the holder with appropriate grades ensures optimum edge life and process stability. This combination supports higher throughput and fewer unexpected stoppages. Workshop-ready reliability and easy integration With a mass of 0.724 kg and a compact cutting-head width of 12.5 mm, the MTENN arrangement is easy to mount and balances well on common toolposts or turrets. The ISO designation MTENN 2525 simplifies procurement and machine setup, while the compatibility note for TN-- 1604 inserts helps planners standardise tooling. The result is a durable clamping solution that slots into existing tool inventories, lowers setup complexity and supports consistent production quality in small-batch and serial turning alike. Contact Metav Werkzeuge today for procurement and technical advice on the MTENN clamping holder with 25 mm body and 150 mm length Technical data Article number: D110TM Manufacturer: Teknik Makina ISO designation: MTENN 2525 Compatible inserts: TN-- 1604 Data Overall length: 150 mm Weight: 0.724 kg Body width: 25 mm Cutting head width: 12.5 mm Cutting height: 35 mm Cutting angle: 60° Special features For TN-- 1604 indexable inserts M16 shank/interface Product type: Clamping holder Brand: Teknik Makina FAQ What inserts are compatible with this holder? The clamping holder is specified for TN-- 1604 indexable inserts and the MTENN 2525 interface ensures correct positioning. Is the MTENN 2525 suitable for general turning tasks? Yes, the MTENN 2525 toolholder with its 60° cutting angle is aimed at standard turning profiles and common workshop applications. How does the holder affect machining accuracy? The compact 25 mm body and 150 mm overall length reduce deflection, improving surface finish and dimensional repeatability when the MTENN clamping holder is used. What mounting interface is used on the holder? The holder employs an M16 shank/interface and an ISO MTENN 2525 designation to match common turret and toolpost fittings. Can insert changes be performed quickly? Yes, the clamping geometry has been designed for straightforward, repeatable insert replacement to support efficient tool changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

A compact, rigid clamping toolholder with a 25 x 25 mm shank, 150 mm overall length and compatibility with DN-- 1506 indexable inserts — delivering predictable cutting geometry and stable clamping. Order the Klemmhalter DDNNN 2525 directly via Metav Werkzeuge or ask our consultants if needed. Klemmhalter — DDNNN 2525 clamping toolholder for DN-- 1506 indexable inserts (Teknik Makina) A Klemmhalter clamping holder engineered to secure DN-- 1506 indexable inserts for compact turning applications, combining a standardised shank with a controlled cutting geometry. 25 x 25 mm shank for rigid clamping Compatible with DN-- 1506 inserts 150 mm overall length for compact setups 62.5° cutting angle for stable cutting Greater rigidity for steady machining results The DDNNN 2525 holder is designed around a 25 x 25 mm shank that prioritises rigidity and repeatability at the toolpost. This robust cross-section reduces vibration and deflection during cutting, which in turn supports improved surface finish and extended insert life. With the ISO DDNNN 2525 designation and a compact 150 mm overall length, the holder integrates into machining centres and lathes where a short overhang and predictable behaviour are required. The combination of structural stiffness and standard geometry makes this a practical choice for workshops seeking consistent turning performance. Secure insert clamping and predictable cutting geometry Clamping is arranged to accept DN-- 1506 indexable inserts and to maintain the correct seating under cutting forces. The toolholder presents a 40 mm cutting height and a 12.5 mm cutting‑head width that together position the insert reliably at the intended datum. A defined 62.5° cutting angle offers controlled engagement with the workpiece, aiding chip formation and dimensional hold. The M15 thread interface provides a straightforward mechanical connection for mounting or replacement, supporting quick insert changes and dependable repeatability under varied cutting conditions. Compact design for easy workshop integration At just 150 mm long and weighing 0.724 kg, this clamping toolholder occupies little bench or turret space while still delivering a solid toolholding solution. The modest footprint reduces interference in multi‑tool arrangements and simplifies setup in confined fixtures. Compliance with the DDNNN format ensures compatibility with standard indexable insert families, making inventory management easier. For production environments where uptime and consistent results matter, the holder’s combination of compactness and standardised dimensions helps streamline tooling routines and reduce changeover times. For tailored advice on Teknik Makina toolholders and to confirm compatibility with individual machines, contact Metav Werkzeuge — info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: D106TM Brand: Teknik Makina Compatible inserts: DN-- 1506 ISO designation: DDNNN 2525 Dimensions & Performance Shank height: 25 mm Shank width: 25 mm Cutting-head width: 12.5 mm Cutting height: 40 mm Overall length: 150 mm Weight: 0.724 kg Cutting angle: 62.5° Mounting thread/interface: M15 Features & Compatibility For DN-- 1506 indexable inserts ISO standardised DDNNN 2525 format Compact 150 mm footprint Clamping design for indexable inserts FAQ Which indexable inserts fit this holder? The holder accepts DN-- 1506 indexable inserts and is specified as DDNNN 2525 for correct fit and seating. What are the main dimensions to consider for fixture planning? Shank 25 x 25 mm, overall length 150 mm, cutting‑head width 12.5 mm and cutting height 40 mm; weight 0.724 kg. What cutting geometry does the toolholder present? The toolholder positions the insert at a 62.5° cutting angle to support consistent chip control and dimensional stability. Which mounting interface is required? A M15 interface is provided for mounting; check turret or toolpost compatibility before installation. Is this holder suitable for compact multi‑tool arrangements? Yes — the 150 mm overall length and standardised format make it suitable where a short overhang and compact tool layout are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Combining a robust 32 mm body, compatibility with DN--1506 indexable inserts and a precise 62.5° cutting angle delivers stable, repeatable turning performance; order the DDNNN clamping holder directly via Metav Werkzeuge or consult the Metav team for application advice. Klemmhalter DDNNN 3232 — DDNNN clamping holder for DN--1506 indexable inserts (Teknik Makina) A Klemmhalter DDNNN 3232 designed for secure mounting of DN--1506 indexable inserts in turning and grooving operations, suited to industrial workshop use Compatibility with DN--1506 inserts 32 mm body width for stable support 62.5° cutting angle for defined chip flow Durable 1.29 kg construction for minimal vibration Consistent clamping geometry for reliable part quality The DDNNN-style clamping holder provides a stable tool position that reduces vibration and machining variance. With a 32 mm body width and a defined 62.5° approach, the holder secures the insert so that cutting forces remain consistent cycle after cycle. This predictable geometry benefits repeatability on medium- to high-volume turning tasks and helps maintain dimensional tolerances without constant readjustment. The ISO designation DDNNN 3232 indicates the standardised fit and orientation that workshop engineers expect when integrating toolholders into established toolposts. Robust build to shorten set-up and boost uptime A rigid clamping interface and compact form reduce the frequency of re‑clamping and adjustment, resulting in lower set-up times between jobs. The compact head width of 16 mm and a cutting height of 40 mm allow integration into tight turret positions while preserving clearance for chip evacuation. The overall length of 170 mm balances reach and stiffness for a wide range of turning and profiling operations. The holder’s mass (1.29 kg) contributes to damping of transient cutting forces, which supports longer tool life for the inserts and steadier surface finishes on workpieces. Compatibility that simplifies inventory management Designed for use with DN--1506 indexable inserts and a P15 shank designation for the relevant boring bar range, the holder reduces the number of adapter types required across turning centres. Standardised interface dimensions mean that inserts from approved series seat reliably, so setting sheets and process windows remain stable when inserts are changed. For procurement and maintenance teams, this compatibility lowers the logistical overhead and simplifies reorder cycles while preserving machining performance. Practical advantages for workshop workflows The holder’s compact geometry and standardised ISO labelling enable fast identification and replacement on the shop floor. Reduced vibration and a well-defined cutting angle support improved surface integrity, which in turn decreases downstream inspection time and rework. For workshops seeking a balance between tool stability and flexibility, this clamping holder offers an efficient route to consistent production results with minimal adjustment effort. For tailored recommendations on mounting or process parameters, Metav Werkzeuge’s application specialists can provide machining guidance. Contact Metav Werkzeuge for precise application advice on Teknik Makina clamping holders and arrange procurement directly from Metav’s Emmerich hub Technical data Article number: D109TM Manufacturer: Teknik Makina Designation: Klemmhalter DDNNN 3232 For indexable inserts: DN-- 1506 SKU: D109TM Facts Body height: 32 mm Body width: 32 mm Head width: 16 mm Cutting height: 40 mm Cutting angle: 62.5° Overall length: 170 mm Weight: 1.29 kg eCl@ss: 21181004 Special features Compatible with DN--1506 indexable inserts ISO designation DDNNN 3232 Boring bar/shank designation P15 Suitable for turning and grooving operations Brand: Teknik Makina FAQ Which inserts fit this clamping holder? The clamping holder is designed for DN--1506 indexable inserts; compatibility is ensured by the ISO DDNNN 3232 interface. What is the cutting angle and why does it matter? A 62.5° cutting angle defines the insert approach and helps control chip flow and cutting forces, improving surface finish and repeatability. What are the key dimensions to check for turret clearance? Check the body height 32 mm, body width 32 mm, head width 16 mm and overall length 170 mm against available turret space. How heavy is the holder and what is the effect on machining? The holder weighs 1.29 kg, which contributes to vibration damping and increases rigidity for steadier cuts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Achieve secure right-hand turning with internal coolant, precise compatibility for VBMT 1604 inserts and robust ISO SVJBR 2525 clamping — a compact solution engineered for repeatable results on production lathes; order the holder directly via Metav Werkzeuge or consult the team for fitment advice. SVJBR 2525 clamping holder – right-hand, internal coolant (Teknik Makina) The SVJBR 2525 clamping holder is a right-hand toolholder for turning applications with VBMT 1604 indexable inserts, designed for secure clamping and integrated coolant supply to improve chip control and tool life Right-hand turning with fixed 93° cutting angle Internal coolant for improved chip evacuation Compatible with VBMT 1604 indexable inserts ISO SVJBR 2525 form with 150 mm overall length Stable clamping for predictable turning accuracy A compact, purpose-built clamping solution ensures consistent contact between insert and holder. With a clamp height of 25 mm and an effective cutting height of 40 mm, the design reduces deflection during interrupted cuts and long turning passes. The head width of 32 mm and a nominal 93° cutting angle give a neutral engagement geometry that simplifies setup and reduces the need for repeated adjustments. For workshop planners this means fewer rejects and less rework: the holder translates insert geometry into reliable cutting performance, and the ISO designation SVJBR 2525 makes integration straightforward where standardised interfaces are used. Productivity gains through coolant and compact integration Integrated internal coolant directs cutting fluid close to the cutting edge, improving lubrication and chip evacuation for longer insert life and steadier surface finish. The compact shank design (M16-IK) and 150 mm overall length enable tight clearances on multi-tool turrets while the low mass (approx. 0.192 kg) helps reduce vibration transfer. The holder accepts the common VBMT 1604 insert form and secures it with a Torx fastener (T15), using a M3.5x11 screw and the matching TA034 locating plate for rapid, repeatable insert changes. These technical choices are made to support higher spindle speeds and uninterrupted production cycles, turning technical detail into measurable throughput gains. Practical fitment, applications and workshop confidence Designed for right-hand turning tasks, this clamping holder suits general machining shops, subcontract turning centres and in-house production lines that rely on standardised indexable inserts. The holder’s compact geometry is particularly useful for finishing passes and semi-finishing where rigidity and coolant access are decisive. Metav’s product curation and logistics mean the component is delivered from a quality-controlled stock in Emmerich with documentation and fast shipping options, providing a trustworthy supply channel for maintenance and production planning. For procurement and floor managers, the combination of standard ISO form, coolant capability and simple mechanical fixing offers a pragmatic balance between performance and operational ease. Contact Metav Werkzeuge for tailored advice on Teknik Cutting Tools SVJBR 2525 clamping holders and to confirm compatibility with existing toolposts and turret systems Technical data SKU: AP546TM Manufacturer: Teknik Makina ISO designation: SVJBR 2525 Article name: SVJB for VBMT Indexable Inserts Facts Overall length: 150 mm Clamp height: 25 mm Head width: 32 mm Cutting height: 40 mm Weight: 0.192 kg Cutting angle: 93° Special features Internal coolant: yes Direction: right-hand Compatible inserts: VBMT 1604 Shank / bore holder: M16-IK U-plate: TA034 Torx key: T15 Torx screw: M3.5x11 FAQ What insert type does this holder accept? The holder accepts VBMT 1604 indexable inserts and is supplied in the ISO form SVJBR 2525 (SKU AP546TM) for standardised fitment. Is coolant supply integrated in the toolholder? Yes — internal coolant is provided to direct fluid to the cutting zone, improving chip control and insert life. Which direction of cut is the holder designed for? This is a right-hand clamping holder intended for conventional right-hand turning operations. What mounting / shank interface does it require? The toolholder is specified with a M16-IK shank designation and suits compatible boring bars or toolposts designed for that interface. Are the fastening parts standardised for simple maintenance? Fastening uses a Torx T15 and a M3.5x11 screw together with the TA034 locating plate for quick and repeatable insert changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of a secure clamp system and internal coolant ensures stable, long‑running left‑hand turning operations with consistent surface finish. Benefit from compatibility with DCMT/VCMT indexable inserts and robust geometry to reduce vibration and tool change time — order the holder directly via Metav Werkzeuge or request technical advice from our consultants. SVJCL 2020 clamping toolholder (SVJC for VCMT indexable inserts) — left‑hand with internal coolant The SVJCL 2020 clamping toolholder is a left‑hand turning tool designed for VCMT/DCMT indexable inserts, delivering secure clamping and integrated coolant for machining centres and conventional lathes. Left‑hand turning orientation (left) Internal coolant channel for reliable chip clearance Fits DCMT/VCMT indexable inserts Overall length 150 mm, robust 0.735 kg Stable performance for left‑hand turning and repeatable results Engineered for precision turning, this clamp‑style toolholder provides a defined cutting angle of 93°, which positions the insert for controlled chip formation and consistent contact pressure. The holder accepts standard DCMT/VCMT indexable inserts, enabling quick index changes and familiar insert geometry for toolrooms and production lines. Reduced setup time and repeatability are the primary benefits: repeatable seating and clamping lower scrap rates and shorten machine downtime, while established insert formats keep tooling logistics simple. Integrated coolant and secure clamping for longer insert life The internal coolant channel improves cooling at the cutting edge, supporting longer cutting intervals and more predictable tool wear. With the dedicated clamping plate TA034 and the supplied fastening hardware (Torx screw M3.5x11, Torx key T15), the insert is held firmly to minimise micro‑movement under load. This combination reduces thermal softening and edge chipping, which in turn increases productive cutting time and helps maintain surface quality on turned components — a direct economic advantage on medium‑ to high‑volume batches. Robust dimensions that enhance rigidity and reduce vibration With an overall length of 150 mm and a weight of 0.735 kg, the toolholder balances reach and rigidity for stable turning operations. Key dimensions such as a cutting height of 35 mm, a holder height of 25 mm, and a cutting‑head width of 32 mm contribute to a low‑vibration setup that supports better surface finish and longer insert life. The shank designation K16‑IK indicates the mounting profile, making integration into existing toolposts straightforward and ensuring secure support during heavy cuts. For technical consultation on integrating the SVJCL 2020 into existing setups or to request a quote, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 — our specialists will advise on suitability and supply options Technical data Article number: AP535TM Manufacturer: Teknik Makina ISO designation: SVJCL 2020 Product type: SVJC for VCMT indexable inserts Facts Overall length: 150 mm Cutting height: 35 mm Holder height: 25 mm Cutting head width: 32 mm Holder width: 25 mm Weight: 0.735 kg Cutting angle: 93° ECLASS: 21181004 Special features Internal coolant: yes Fits inserts: DCMT 11T3 / VCMT Clamping plate: TA034 Torx screw: M3.5x11 Torx key: T15 Shank designation: K16‑IK Cutting direction: left FAQ Is this holder suitable for standard DCMT and VCMT inserts? The SVJCL 2020 holder is specified for DCMT 11T3 and compatible VCMT indexable inserts, enabling use of common turning inserts in production and repair workshops (AP535TM). Does the toolholder provide coolant to the insert tip? Yes — the holder includes an internal coolant channel, delivering coolant towards the insert to improve tool life and surface finish during sustained turning operations. What mounting or fastening parts are supplied? The holder is supplied with the designated clamping plate TA034 and uses a Torx screw M3.5x11 (Torx key T15) for secure retention of the insert seat. Can this holder be mounted in a standard toolpost with a K16 profile? The shank designation K16‑IK indicates compatibility with toolposts and boring bars accepting that profile; the holder offers straightforward integration where the K16 mounting is used. Is the SVJCL 2020 suitable for heavy roughing cuts? The toolholder’s robust geometry, defined cutting height and mass (0.735 kg) give it good rigidity for many turning tasks; assessment for heavy roughing should consider the machine power, insert grade and cutting parameters. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise clamping, internal coolant and compact dimensions to maintain cycle-time stability and extend insert life; order the holder directly via Metav Werkzeuge or consult our tooling specialists for application-specific advice. SVJCR 2525 — SVJC for VCMT Indexable Inserts, internal coolant, right-hand SVJCR 2525 is a right-hand clamping holder designed for turning applications with VCMT/DCMT-style indexable inserts; ideal for medium-duty external turning where secure insert retention and coolant supply increase productivity. Right-hand turning orientation Internal coolant supply Compatible with DCMT 11T3 inserts ISO designation SVJCR 2525 Consistent right-hand turning for stable throughput The holder delivers repeatable clamping and a defined cutting geometry that reduces setup time and stabilises cycle times. With a right-hand orientation and a 93° approach angle, the toolholder is intended for conventional turning operations where predictable chip formation and tool behaviour are required. The overall length of 150 mm and compact head width minimise overhang, which in turn reduces vibration and supports more consistent surface finish and dimensional control—benefits that translate directly into fewer reworks and higher process reliability. Secure clamping and coolant to extend insert life A secure clamping mechanism, specified under ISO SVJCR 2525, holds DCMT/VCMT indexable inserts firmly and is tightened using an M3.5x11 Torx screw (T15), ensuring repeatable torque and seating. The integrated internal coolant channel supplies coolant directly to the cutting edge; this reduces thermal load, improves chip evacuation and commonly extends the service life of carbide inserts. For manufacturers seeking to lower tooling costs per component, the combination of firm clamping and directed coolant provides a measurable reduction in wear and a more stable cutting process. Compact footprint and straightforward integration Designed with a 25 mm shank width and a 25 mm holder height, together with a 32 mm cutting-head width, this clamping holder fits common turret and toolpost setups while keeping footprint small. The modest weight of 0.735 kg and standardised interface simplify handling and changeover; the holder accepts the common DCMT 11T3 insert form factor, which facilitates stocking and reduces inventory complexity. Where quick set-up is essential, the standardised dimensions and familiar screw interface enable rapid installation with existing tooling hardware. Practical advantages for workshop and production use Because the design focuses on proven interface standards and coolant-fed cooling, it suits both jobbing shops and production lines where repeatability and uptime are priorities. The robust construction and clear ISO designation make procurement and QA processes straightforward, while the compatibility with commonly used indexable inserts ensures broad applicability across turning tasks. Technical advisors are available to discuss specific workpiece materials and machining parameters to ensure the holder matches the intended application. Contact Metav Werkzeuge for tailored tooling recommendations and request the SVJCR 2525 right-hand clamping holder with internal coolant (AP526TM) — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: AP526TM Manufacturer: Teknik Makina Designation: SVJC for VCMT indexable inserts ISO designation: SVJCR 2525 Facts Cutting height: 35 mm Holder height: 25 mm Shank width: 25 mm Cutting-head width: 32 mm Overall length: 150 mm Weight: 0.735 kg Cutting direction: right Approach angle: 93° Compatible inserts: DCMT 11T3 Coolant: internal Special features Clamping plate: TA034 Torx screw: M3.5x11 Torx key size: T15 Right-hand orientation Suitable for VCMT/DCMT indexable inserts FAQ Which insert types fit this holder? The clamping holder is intended for DCMT / VCMT indexable inserts; the geometry matches DCMT 11T3-style inserts to ensure correct seating and cutting clearance. Does the holder provide coolant to the insert tip? Yes, the toolholder features an internal coolant channel that supplies coolant close to the cutting edge to support chip control and reduce thermal loading. What fastener is used to secure the insert? An M3.5x11 Torx screw is used for insert clamping; the required Torx key size is T15, providing consistent torque for repeatable clamping. Is this holder suitable for left-hand turning? No, the holder is specified for right-hand turning; left-hand operations require the corresponding left-hand variant. Can the holder be mounted in standard toolposts and turrets? Yes, the holder's standardised shank dimensions and ISO designation are compatible with common turret and toolpost interfaces used in turning centres. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the holder's compatibility with TN-- 2204 inserts, robust MTJNR 2525 shank format and compact geometry to improve turning stability and setup repeatability; order directly via Metav Werkzeuge or consult the team in Emmerich for specification matching. Clamping holder MTJN D202TM — right-hand, for TN-- 2204 indexable inserts (Teknik Makina) Clamping holder MTJN D202TM is a right-hand turning toolholder designed for stable clamping of TN-- 2204 indexable inserts in standard lathe applications. Right-hand cutting orientation Compatible with TN-- 2204 inserts ISO MTJNR 2525 shank format 150 mm length, 93° cutting angle Increased stability for reliable turning results The holder's compact geometry and clearly defined dimensions deliver repeatable clamping and reduced vibration during machining. With a total length of 150 mm and a cutting height of 40 mm, the assembly keeps the insert in an optimal position for consistent chip formation. The 93° cutting angle supports an effective approach to the workpiece, improving surface finish and tool life when paired with the correct insert grade. These concrete attributes translate into predictable process behaviour and fewer unexpected adjustments at the machine. Secure clamping and robust construction for daily use A firm connection between insert and holder is essential for productivity; the MTJN design secures TN-- 2204 indexable plates in a stable seat, while the holder head width of 32 mm and holder height of 25 mm add rigidity at the cutting zone. The unit's weight of 0.775 kg contributes to dampening minor oscillations without excessive bulk. The ISO designation MTJNR 2525 indicates a standard shank format that simplifies toolpost set-up and interchangeability across machines equipped for this holder family, reducing downtime during tool changes. Easy integration into workshop workflows and support from Metav Compatibility with widely used TN-- inserts and the right-hand orientation make the holder straightforward to integrate into existing tooling systems. The shank specification M22 for the bore-bar interface provides clarity for choosing compatible adaptors and fixtures. For complex orders or to confirm fitment with specific toolposts, Metav Werkzeuge's advisors are available to provide dimension checks and delivery guidance directly from Emmerich. This combination of technical clarity and regional supply reliability helps workshops maintain steady production and reduces procurement uncertainty. Contact Metav Werkzeuge in Emmerich for precise fitment advice and reliable supply: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: D202TM SKU: D202TM Designation: MTJN for TN-- Indexable Inserts Brand: Teknik Makina ISO designation: MTJNR 2525 Facts Total length: 150 mm Cutting height: 40 mm Holder height: 25 mm Head width: 32 mm Holder width: 25 mm Weight: 0.775 kg Cutting angle: 93° Direction: right Suitable for inserts: TN-- 2204 Bore/shank designation: M22 Special features Clamping holder design MTJN Right-hand turning orientation Compatible with TN-- 2204 indexable inserts Standardised MTJNR 2525 shank format FAQ Is this holder suitable for standard lathe toolposts? The clamping holder MTJN D202TM fits toolposts designed for ISO MTJNR 2525 shanks and is intended for standard lathe turning applications with right-hand cutting orientation. Which indexable inserts are compatible? The holder is specified for TN-- 2204 indexable inserts; compatibility is ensured when matching insert geometry and thickness to the MTJN seat. What are the key dimensions to check before ordering? Confirm total length (150 mm), cutting height (40 mm) and shank format MTJNR 2525 to ensure correct fit on the machine and in the toolpost. Can this holder be used for both roughing and finishing? Yes; the secure clamping and 93° cutting angle make the holder suitable for a range of turning tasks, provided the insert grade and cutting parameters are selected for the intended operation. Where can dimensional or application queries be clarified? Metav Werkzeuge can provide additional technical clarification and delivery options from Emmerich; contact info@metav-werkzeuge.com or call +49 2822 7131930 for assistance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a rigid clamping concept with compatibility for VBMT 1604 inserts delivers consistent, chatter‑resistant turning and reliable dimensional repeatability; benefit from the left‑hand orientation and robust SVJBL 2525 form for safe chip control. Order directly via Metav Werkzeuge or consult the specialists for application-specific advice. Klemmhalter SVJB for VBMT Indexable Inserts (SVJBL 2525) — Left‑hand clamping holder, 150 mm overall length — Teknik Makina The Klemmhalter SVJB for VBMT Indexable Inserts is a left‑hand clamping holder designed for turning operations with VBMT 1604 inserts, suited to workshop and small‑batch production environments where stability and repeatable set‑up matter. Left‑hand turning orientation for precise cuts Compatible with VBMT 1604 indexable inserts Solid SVJBL 2525 clamping form for stability 150 mm overall length, M16 shank thread Stable clamping for repeatable turning performance The holder's engineered clamp geometry provides a consistent seating for indexable inserts, reducing vibration and improving surface finish on turned components. With a nominal cutting angle of 93° and a clamping form based on SVJBL 2525, the design focuses on axial stability during left‑hand operations. For production runs where part tolerance and tool life are critical, the combination of secure clamping and correctly matched insert size VBMT 1604 leads to fewer set‑ups and less rework, improving overall process efficiency. Compact dimensions that simplify set‑up and handling Measured at 150 mm overall length with a head width of 32 mm and a holder height of 25 mm, the tool balances reach with rigidity. The shank uses an M16 thread interface for secure attachment to compatible tool posts. A cutting edge height of 40 mm ensures correct insert alignment in common turret systems, while the relatively low mass (0.688 kg) helps reduce inertia on smaller lathes. These dimensional details make calibration straightforward and shorten downtime during tool changes. Application focus: left‑hand turning and practical workshop use Intended for left‑hand cutting, this holder suits turning tasks where chip flow and tool orientation demand a dedicated solution. Compatible with VBMT 1604 inserts, the design supports general turning, light roughing and finishing passes depending on insert grade. The robust holder form contributes to predictable wear patterns on inserts, enabling planned index changes and better cost control in small‑ to medium‑scale machining operations. Reliability and service from a precision partner Supplied by Teknik Cutting Tools and available through Metav Werkzeuge, the unit benefits from consistent quality checks and a reliable supply chain. Metav's European distribution acts as a quality filter for workshop equipment, backed by extensive product range and a strong service network. For operations seeking dependable clamping performance and short lead times, this holder combines a standard ISO designation with practical features that support repeatable manufacturing. For a tailored assessment of whether this left‑hand SVJBL 2525 holder from Teknik Cutting Tools fits the intended turning application, contact Metav Werkzeuge for expert advice and reliable supply — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: D382TM Manufacturer: Teknik Cutting Tools Brand: Teknik Makina Product name: Klemmhalter SVJB for VBMT Indexable Inserts (SVJBL 2525) Facts Overall length: 150 mm Holder height: 25 mm Head width: 32 mm Holder width: 25 mm Cutting edge height: 40 mm Weight: 0.688 kg Cutting angle: 93° Shank thread: M16 Compatible insert: VBMT 1604 Cutting direction: left ECLASS: 21181004 SKU: D382TM Special features ISO designation: SVJBL 2525 Designed for VBMT 1604 indexable inserts Left‑hand orientation for specific turning tasks Robust clamping form for improved stability FAQ Which insert type fits this holder? The holder is specified for VBMT 1604 indexable inserts; this format provides the intended seating and cutting geometry for stable turning. Is the holder suitable for right‑hand turning? This version is designed for left‑hand cutting; for right‑hand operations a right‑hand variant should be selected. What is the mounting interface for the holder? The shank uses an M16 thread interface for secure mounting to compatible tool posts and adaptors. How does the cutting angle affect machining? The 93° cutting angle gives a neutral geometry that balances radial and axial forces, supporting controlled chip flow and surface finish in turning operations. Does the holder require special inserts or grades? Standard VBMT 1604 inserts in appropriate grades for the work material and speed can be used; tool grade selection depends on the specific workpiece material and cutting conditions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise clamping, robust dimensions and a secure insert interface for consistent right-hand turning operations; combine rigidity and repeatability to reduce rework and downtime. Order or request advice via Metav Werkzeuge for a reliable supply and technical guidance. Clamping holder DCLN for CN-- indexable inserts (ISO DCLNR 2525) — right-hand, 25 mm shank height The clamping holder DCLN is designed for right-hand turning with CN1204 indexable inserts and provides a compact, rigid mounting solution for turning applications Right-hand turning configuration Compatible with CN1204 inserts ISO DCLNR 2525 designation Robust 25 mm shank height Engineered for consistent right-hand turning performance The toolholder is built to deliver repeatable results in turning operations where stability matters. The DCLNR 2525 geometry and a 95° approach angle translate into predictable chip flow and tool engagement, which supports stable cutting forces and consistent part quality. Specified as a right-hand configuration, this clamping solution reduces the need for trial-and-error setup and shortens cycle-time variability, helping machine shops increase throughput without sacrificing precision. Dimensions and mass that improve rigidity and vibration control With a shank height of 25 mm, an overall length of 150 mm and a cutting-head width of 32 mm, the holder balances accessibility with structural stiffness. The relatively compact footprint and a mass of 0.785 kg reduce overhang-induced deflection while keeping the tooling envelope manageable for a range of lathes. These dimensional choices minimise chatter and enable higher stable cutting parameters, which in turn reduces secondary finishing and scrap rates. Fast insert changes and standardised interfaces for uptime Designed for CN1204 indexable inserts and identified as DCLN for CN-- indexable inserts, the holder accepts standard insert geometries and a familiar clamping routine. The M12 shank designation ensures a secure connection to compatible tool posts or tool blocks, while the 30 mm cutting height supports correct insert seating and engagement. This combination enables a quick insert change process, which shortens maintenance stops and keeps production running with minimal interruption. Practical fit for workshop workflows and quality-conscious buyers This clamp-style toolholder suits businesses that prioritise operational reliability and measurable productivity gains. The compact, right-hand design saves turret space and simplifies tool library management. Choosing a standardized holder like this supports predictable inventory, easier replacement and traceable performance in day-to-day turning tasks. Backed by Metav’s role as a European quality filter and supply partner, the component integrates into broader workshop procurement strategies focused on repeatability and dependable delivery. Contact Metav Werkzeuge for tailored application advice on the Teknik Makina clamping holder and to secure supply arrangements; phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: D162TM Manufacturer: Teknik Makina Designation: DCLN for CN-- Indexable Inserts (ISO DCLNR 2525) Facts Height: 25 mm Shank width: 25 mm Cutting head width: 32 mm Cutting height: 30 mm Cutting angle: 95° Total length: 150 mm Weight: 0.785 kg Direction: right-hand Special features Fits CN1204 indexable inserts ISO designation DCLNR 2525 Shank designation M12 Suitable for right-hand turning FAQ What inserts fit this holder? The holder is specified for CN1204 indexable inserts; compatibility is based on the CN1204 geometry and standard clamping dimensions. Is the holder suitable for right-hand turning only? Yes, this tool is configured as a right-hand clamping holder and is optimised for right-hand turning cycles. What are the key dimensional constraints to consider for machine setup? Important dimensions include a shank height of 25 mm, overall length 150 mm and cutting-head width 32 mm; these determine clearance and stiffness in the turret or tool post. Which shank or mounting interface is required? The holder includes a M12 shank designation for secure attachment to compatible tool mounts. Can this holder support quick insert changes on the shop floor? Yes, the standardised insert seat and clamping design enable quick insert change routines, reducing downtime during tool exchanges. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of precise clamping, standardised insert compatibility and a compact design to maintain steady turning cycles; order directly via Metav Werkzeuge or consult our specialists for application advice. Klemmhalter DWLNL 2525 — Left‑hand turning holder for WN-- indexable inserts (Teknik Makina) A durable clamping holder engineered for left‑hand turning with WN-- 0604 indexable inserts, offering standardised seating and stable tool engagement DWLNL 2525 ISO designation for secure fit Compatible with WN-- 0604 indexable inserts 25 mm clamping height, 32 mm cutting head width Left‑hand cutting direction, 95° cutting angle Optimised rigidity for repeatable turning results The toolholder delivers consistent machining through a stable clamping interface and a robust head geometry. With a clamping height of 25 mm and a cutting head width of 32 mm, the design reduces vibration and increases repeatability in serial turning operations. The 95° cutting angle promotes effective chip evacuation and lowers cutting forces, which helps achieve improved surface finishes and longer insert life. This mechanical stability translates directly into fewer reworks and more predictable cycle times on the shop floor. Standardised insert interface for quick tool changes The holder is designed around the DWLNL 2525 seat to accept common indexable grades, specifically the WN-- 0604 family of inserts, enabling fast replacement and a uniform clamping plane. Standardisation of the insert interface reduces setup time and simplifies tool inventory management. In practice, this means quicker changeovers between jobs and reduced downtime, especially useful in batch production. The left‑hand orientation is explicitly matched to the cutting direction, avoiding ambiguity during tool selection and ensuring correct mounting from the outset. Compact dimensions and handling that aid workshop efficiency Built for practical handling, the unit features an overall length of 150 mm and a mass of 0.772 kg, offering a balance between reach and rigidity that suits lathes and turning centres with limited overhang. The cutting height of 26 mm aligns the insert with typical toolpost geometries to minimise setup adjustments. A clamping screw designation of M06 provides secure fixation and straightforward maintenance. Together, these measured dimensions make the holder a reliable choice for everyday turning tasks where predictable positioning and ergonomic handling are priorities. For tailored technical advice on Teknik Cutting Tools turning holders or to discuss suitability for specific machining tasks, contact Metav Werkzeuge for expert guidance and order support by calling +49 2822 7131930 or emailing info@metav-werkzeuge.com Technical Data Article number: D319TM Manufacturer: Teknik Makina Type: DWLN for WN-- Indexable Inserts ISO designation: DWLNL 2525 Facts Clamping height: 25 mm Cutting head width: 32 mm Body width: 25 mm Cutting height: 26 mm Overall length: 150 mm Weight: 0.772 kg Cutting angle: 95° Cutting direction: left Special features Suitable for WN-- 0604 indexable inserts Clamping screw designation: M06 ISO designation: DWLNL 2525 FAQ What insert size does this holder accept? The holder is designed for WN-- 0604 indexable inserts and uses the standard DWLNL seating for secure positioning. Is the holder suitable for left‑hand turning only? Yes, the toolholder is configured for left‑hand turning, matching the cutting direction specified for the DWLNL 2525 seat. What are the key dimensions to check before mounting? Important dimensions include a clamping height of 25 mm, overall length of 150 mm, and a cutting head width of 32 mm; these determine compatibility with the toolpost and insert position. Which clamping screw is required for maintenance? The clamping screw designation is M06, which should be used for secure tightening and maintenance procedures. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a stable 95° cutting angle and a compact 25 mm shank for dependable turning performance; combine compatibility with WN-- 0804 indexable inserts and a 150 mm overall length for easy integration into existing tooling lines — order the Klemmhalter directly via Metav Werkzeuge or ask our consultants if further specification details are required. Klemmhalter DWLNR 2525 (D178TM) — Right-hand turning holder for WN-- 0804, 95° cutting angle The Klemmhalter DWLNR 2525 is a right-hand turning holder designed for DWLN-style indexable inserts (WN-- 0804), engineered to provide secure clamping and consistent geometry in medium-duty turning applications Right-hand holder for WN-- 0804 inserts 95° cutting angle for reliable chip control Robust 25 × 25 mm shank, 150 mm overall length Precision clamping for consistent turning results A properly configured holder ensures repeatable part quality; this toolholder features a 25 mm shank and a 32 mm cutting-head width that together deliver stable support during cuts. The 95° cutting angle aids chip flow and contact geometry, reducing the likelihood of vibration and improving surface finish. Because the insert seat matches the WN-- 0804 form, insert seating is precise and repeatable, which shortens set-up checks and helps maintain process tolerances across production runs. Designed for productivity and seamless machine integration The holder’s 150 mm overall length and right-hand orientation make it straightforward to insert into standard toolposts without compromising accessibility. The clamping system accepts the M08 fixing, enabling secure, fast clamping of the insert and minimising downtime during changeovers. With a compact profile and a 32 mm cutting height, the toolholder supports efficient chip evacuation and allows operators to keep feeds and speeds optimised for increased throughput. Built for durability and predictable handling At approximately 0.793 kg, the unit balances rigidity with manageable handling for rapid tool changes. The ISO designation DWLNR 2525 signals compatibility with established toolholding standards, simplifying procurement and inventory management. Manufactured by Teknik Cutting Tools, the holder is intended for shops seeking a reliable, industry-standard clamping solution that reduces setup iterations and supports consistent machining results over time. For personalised technical advice or to arrange procurement of the DWLNR 2525, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 — consultants can advise on machine compatibility and order handling Technical Data SKU: D178TM ISO designation: DWLNR 2525 For inserts: WN-- 0804 Facts Shank width: 25 mm Shank height: 25 mm Cutting-head width: 32 mm Cutting height: 32 mm Overall length: 150 mm Weight: 0.793 kg Cutting angle: 95° Direction: right Special features Clamping screw: M08 Design: DWLN holder for indexable inserts Suitable for medium-duty turning Manufacturer: Teknik Cutting Tools FAQ Which insert type fits this holder? The holder accepts WN-- 0804 indexable inserts; the seat and clamping system are specified for that insert geometry and size. Is the holder right- or left-hand oriented? This toolholder is right-hand oriented, designed for turning operations that require a right-hand approach. What are the key dimensions to check for machine compatibility? Check the 25 mm shank (width and height), 150 mm overall length and the 32 mm cutting height to ensure the DWLNR 2525 fits the toolpost and clears workpiece fixtures. Who manufactures the holder and how is it designated? The holder is produced by Teknik Cutting Tools and carries the ISO designation DWLNR 2525 with SKU D178TM for ordering and identification. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Efficient chip control and consistent clamping are combined in this clamping holder: a 95° cutting angle and 40 mm cutting height deliver secure tool engagement and reliable material removal. With a compact 150 mm overall length and a stable 25 mm width, the design supports repeatable turning operations. Order or request specification guidance through Metav Werkzeuge for smooth integration into production workflows. MWMNN 2525 clamping holder — 95° cutting angle, 40 mm cutting height The MWMNN 2525 clamping holder is designed for turning applications with WN-- 0804 indexable inserts, providing robust clamping and straightforward integration into standard tool posts. MWMNN 2525 profile for WN-- 0804 inserts Cutting height 40 mm for deep operations 95° cutting angle for secure chip control 150 mm overall length, robust 25 mm width Precision engineering for reliable turning results The holder is built to secure WN-- 0804 indexable inserts at a defined 95° cutting angle, which improves chip formation and reduces chatter during interrupted cuts. The specified 40 mm cutting height aligns the tool tip precisely with the workpiece centre in many common set-ups, so consistent part geometry is more easily achieved. The robust clamping interface reduces insert movement under load, enhancing repeatability and prolonging insert life by avoiding micro‑vibrations that accelerate wear. Compact form factor that simplifies machine integration With a 150 mm overall length and a 25 mm holder width, the assembly combines rigidity with compactness for confined tool stations. The 12.5 mm cutting head width supports close‑quarter machining while the 0.724 kg mass helps dampen minor oscillations without adding excessive load to the turret. The ISO designation MWMNN 2525 and the shank reference M08 indicate conventional mounting geometry compatible with many turning tool posts, which reduces setup time and supports fast tool changes in production environments. Practical handling, maintenance and workshop benefits The design focuses on operator efficiency: the clamping mechanics enable secure fixation of the insert and straightforward access for inspection and replacement. As the component is intended for WN-- 0804 inserts, selection of the correct insert grade and geometry remains essential for optimised results in the chosen application. Metav’s distribution and technical advice ensure that matching inserts and mounting accessories are available, backed by the company’s quality filter in Emmerich and a wide product range for workshop consolidation. Contact Metav Werkzeuge for tailored advice and ordering assistance for the Teknik Cutting Tools MWMNN 2525 clamping holder (SKU D116TM) Technical data SKU: D116TM ISO designation: MWMNN 2525 Suitable for: WN-- 0804 indexable inserts Manufacturer: Teknik Makina Facts Overall length: 150 mm Cutting height: 40 mm Holder width: 25 mm Holder height: 25 mm Cutting head width: 12.5 mm Weight: 0.724 kg Cutting angle: 95° Special features Shank/holder reference: M08 Intended use: Turning with indexable inserts Design optimised for secure clamping and repeatability FAQ What inserts fit this clamping holder? The clamping holder is specified for WN-- 0804 indexable inserts, which should be used to ensure correct seating and performance with the MWMNN 2525 profile. Is the holder compatible with standard tool posts? Yes. The ISO designation MWMNN 2525 and the shank reference M08 indicate conventional mounting geometry that is compatible with many standard turning tool posts. How does the 95° cutting angle affect machining? A 95° cutting angle gives a stable cutting edge orientation that improves chip breaking and reduces radial forces, helping to maintain dimensional accuracy and surface finish in interrupted or heavy cuts. What should be considered when replacing inserts? When replacing inserts in this clamping holder, ensure correct insert type (WN-- 0804), clean seating faces, and verify clamping torque to maintain repeatable positioning and prevent premature wear. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Robust clamping and precise indexing reduce setup time while ensuring consistent thread quality; with a 150 mm overall length and a compact 25 mm head it supports stable external threading using 16 ER inserts — order the Klemmhalter directly via Metav Werkzeuge or consult our specialists for application guidance. Klemmhalter D260TM by Teknik Makina — Clamping holder for external threading, compatible with 16 ER, right-hand A Klemmhalter D260TM clamping holder engineered for right-hand external threading on lathes and turning centres, providing compact support for indexable 16 ER inserts and ISO-designated stability Right-hand cutting direction Compatible with 16 ER inserts Cutting head width 25 mm Overall length 150 mm Engineered for stable, high-precision external threading This clamping holder delivers a focused combination of clamping rigidity and dimensional consistency that benefits serial threading tasks. The holder's ISO AL 2525 designation ensures interchangeability in standardised setups, while the compact head dimensions provide a low overhang to reduce vibration. By using 16 ER indexable inserts the toolhead enables fast insert changes and consistent thread form, which supports higher throughput and fewer reworks compared with one-piece tooling. The right-hand cutting orientation is specified for standard clockwise threading operations, providing a predictable cutting geometry for process planning. Faster setup and reliable repeatability for workshop production With an overall length of 150 mm and a head width of 25 mm, the holder is designed to fit tight turret stations while still offering an effective cutting height 30 mm for robust engagement. The specified shank/collet interface (M16–ER16) matches common clamping systems, enabling quick installation and secure fixation without additional adapters. The modest mass of 0.754 kg contributes to easier handling during tool changes and reduces strain on turret drives. These measurable attributes translate into shorter setup cycles and improved repeatability, which is particularly valuable in small-batch production or mixed-process turning. Practical benefits for everyday workshop use and supply reliability The tool holder's straightforward geometry and standardised connections make it suitable for routine maintenance and fast replacement when needed, limiting machine downtime. Compatibility with 16 ER inserts reduces tooling inventory complexity, since the same insert family can be used across multiple holders and operations. Supplied by Teknik Makina and distributed via Metav, the component arrives with traceable specifications so procurement teams can plan supplies with confidence. The design focuses on predictable outcomes: stable clamping, reproducible thread profiles and uncomplicated servicing, which together support a resilient production workflow. For dependable external threading performance with Teknik Makina quality, contact Metav Werkzeuge for tailored advice and next-step ordering — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application fit and availability Technical data Article number: D260TM Manufacturer: Teknik Makina ISO designation: AL 2525 For indexable inserts: 16 ER Facts Overall length: 150 mm Head width: 25 mm Holder height: 25 mm Cutting height: 30 mm Weight: 0.754 kg Cutting direction: right Special features Shank / collet interface: M16–ER16 Application: for external threading Compatible insert family: 16 ER ISO-compatible designation: AL 2525 FAQ Which insert type fits this holder? The holder accepts 16 ER indexable inserts; Teknik Makina's designation aligns the tool with common insert geometries for external threading. Is the cutting direction right-hand or left-hand? This clamping holder is configured for right-hand cutting direction, suitable for standard clockwise threading operations. What are the key dimensions of the tool? Key dimensions: overall length 150 mm, head width 25 mm, cutting height 30 mm; weight is 0.754 kg. Which clamping interface is used for mounting? Mounting is via an M16–ER16 interface, compatible with ER16-style collet systems and quick-fit turrets. Can this holder be used in automated turret systems? Yes, the compact 150 mm length and standardised ISO designation support use in turrets and turning centres where 16 ER insert tooling is employed. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid clamping solution that combines precise fit for KNUX 1604 inserts with a secure M6 locking screw and a robust 25 × 25 mm holder body for consistent turning results; order the clamping holder directly via Metav Werkzeuge or ask the consultants if needed. CKJNL 2525 clamping holder — CKJN for KNUX indexable inserts, left-hand, 25 × 25 mm — Teknik Makina CKJN for KNUX indexable inserts is an engineered clamping holder for left-hand turning, designed to hold KNUX 1604 indexable inserts with reliable rigidity and repeatable positioning. Left-hand cutting orientation Compatible with KNUX 1604 inserts Robust M6 locking screw for secure clamping 25 × 25 mm holder body, 150 mm overall length Rigid design for repeatable machining accuracy The CKJNL 2525 clamping holder is built around a compact 25 × 25 mm cross-section and a 150 mm overall length, offering a balance of stiffness and accessibility for common turning tasks. The combination of a M6 locking screw and the BK028 clamp prong secures the insert seat to minimise micro-movement during cuts. This rigidity translates into improved dimensional repeatability and reduced tool-change adjustments, which supports higher first-pass yield in production settings. Optimised geometry for left-hand turning with KNUX inserts Designed specifically for KNUX 1604 indexable inserts, the toolholder presents a cutting angle of 93° and a cutting head width of 30 mm with a cut height of 35 mm. The left-hand orientation means the insert geometry and holder seating are matched for left-handed operations, preventing misalignment and ensuring consistent chip flow. For workshops standardising on KNUX inserts, this reduces setup time and simplifies inventory by matching holder geometry to the insert form. Practical assembly and maintenance for workshop efficiency Assembly and routine maintenance are straightforward: the clamp plate is secured with an M3x10 screw to the TA046 shim plate while the primary locking is provided by the M6 screw. A 3 Allen key is indicated for the relevant fastenings. These standardised fastenings make insert replacement and re-tightening quick, reducing machine downtime. The holder’s modest mass (approximately 0.75 kg) keeps handling safe while providing sufficient mass to dampen vibration during many operations. Application benefits and production-level reliability With a 25 mm holder width and 25 mm height, the holder suits constrained toolpost configurations while offering a cutting head profile that balances reach and stiffness. The toolholder’s compatibility with KNUX 1604 inserts and its secure clamping arrangement support repeatable surface finish and tolerance control in batch turning. For production environments seeking predictable tool performance, this holder reduces variables that cause scrap or rework and integrates straightforwardly into existing insert-based tooling systems. For precision left-hand turning and reliable clamping with the Teknik Makina CKJNL 2525, contact Metav Werkzeuge for tailored technical advice or to request a quotation — info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: RD034TM Manufacturer: Teknik Makina ISO designation: CKJNL 2525 Compatible inserts: KNUX 1604 Facts Holder width: 25 mm Holder height: 25 mm Cutting head width: 30 mm Cutting height: 35 mm Overall length: 150 mm Weight: 0.75 kg Cutting angle: 93° Special features Cutting direction: left Locking screw: M6 Clamp plate: TA046 Clamp prong: BK028 Clamp screw: M3x10 Allen key: 3 Allen Boring bar designation: M16 FAQ Which indexable inserts are compatible with this holder? The clamping holder is designed for KNUX 1604 indexable inserts and ensures correct seating and chip control when used with those inserts. Is the holder suitable for right-hand turning operations? No, the holder is configured for left-hand cutting; it is intended for left-hand turning and will not provide the intended geometry for right-hand operations. What fastenings and tools are required for assembly? Assembly uses an M6 locking screw for the main clamp and an M3x10 screw for the clamp plate (TA046); a 3 Allen key is indicated for the fastenings. What are the principal dimensions and mass of the holder? Key dimensions: 25 × 25 mm holder body, 150 mm overall length, 30 mm cutting head width, 35 mm cutting height; mass approximately 0.75 kg. What cutting geometry does the holder provide? The toolholder presents a cutting angle of 93° and a left-hand orientation, optimised for stable chip formation and consistent tool engagement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com