Gibt es einen Hahn und Kolb Online Shop?

Take advantage of a secure M12 connection and a 150 mm reach to extend machining capability while preserving rigidity; the combination of a 25 mm shank and a 20.7 mm cutter opening supports stable clamping and predictable tool engagement. Order the extension for screw-in milling cutters directly via Metav Werkzeuge or ask our consultants if needed Extension for screw-in milling cutters VT515TM — M12 thread, 150 mm overall length (Teknik Cutting Tools) Extension for screw-in milling cutters VT515TM is a dedicated toolholder designed to increase reach for screw-in milling operations while maintaining concentricity and clamping stability in production environments M12 thread for secure cutter attachment 150 mm overall length for extended reach 25 mm shank diameter for rigid clamping Weighs 0.542 kg for balanced handling Gain extended reach without compromising engagement The extension provides a 150 mm overall length that allows deeper access to workpieces or additional clearance for fixturing, while the M12 thread and a 40 mm cone engagement ensure the cutter is positively located. The internal opening of 20.7 mm matches standard screw‑in cutter shanks, reducing adaptor stacks and preserving axial alignment. This construction minimises wobble and contributes to reliable repeatability in serial production, which in turn reduces scrap rates and set‑up iterations. Improve rigidity and surface quality with a stout shank A 25 mm shank diameter gives the assembly the necessary stiffness for moderate cutting loads, improving surface finish and extending cutter life through reduced vibration. The extension’s mass (approx. 0.542 kg) is optimised to balance inertia and dynamic stability, so toolpaths remain predictable at typical feed rates used in milling centres. For machine shops seeking consistent results, this means fewer corrective passes and a more efficient machining cycle. Integration and shopfloor benefits for production use Designed for compatibility with screw‑in milling cutters, the component simplifies tooling inventories by enabling existing cutters to reach otherwise inaccessible features. The straightforward mechanical interface shortens changeover time and supports standardised maintenance checks. In practice, the extension is suited to CNC machining centres and toolrooms where extended reach, secure attachment, and dimensional reliability contribute directly to throughput and process stability. For technical advice or to arrange supply of the Teknik Cutting Tools extension (VT515TM), contact Metav Werkzeuge’s specialists at info@metav-werkzeuge.com or call +49 2822 7131930 — assistance and regional supply from Emmerich are available Technical data Article number: VT515TM Manufacturer: Teknik Makina Thread: M12 Weight: 0.542 kg Core dimensions Overall length: 150 mm Shank diameter: 25 mm Cutter opening: 20.7 mm Cone engagement length: 40 mm Special features Screw‑in cutter compatibility Stout shank for improved rigidity Balanced mass for stable handling FAQ Which cutter shank sizes fit this extension? The extension accepts screw‑in milling cutters with a shank opening of 20.7 mm; the M12 threaded interface gives secure axial engagement for standard screw‑in cutters (Teknik Cutting Tools VT515TM). Is the component suitable for use in CNC machining centres? Yes — the 25 mm shank and robust design make the extension appropriate for CNC applications where added reach and rigidity are required. How much extra reach does the extension provide? The overall length of 150 mm increases access compared with standard holders, allowing machining of deeper pockets or improved clearance for fixtures. What ensures the cutter is securely retained? Retention is delivered through the M12 thread combined with a 40 mm cone engagement, which together ensure positive location and repeatable concentricity for the cutter. Can this extension affect surface finish or tool life? By increasing stiffness through the 25 mm shank and limiting play at the connection, the extension supports improved surface finish and can reduce premature cutter wear under comparable cutting conditions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a precise, rigid extension designed for screw-in cutters: M10 thread for secure mounting and a 150 mm overall length for extra reach while maintaining concentricity and balance; order the extension via Metav Werkzeuge or request bespoke advice for integration into existing toolholders. Extension for screw-in milling cutters – M10 thread, 150 mm length by Teknik Makina The Extension for screw-in milling cutters is a purpose-built toolholder component that extends the working reach of screw-in cutters while preserving rigidity and runout control for workshop and CNC applications M10 thread for secure attachment 150 mm overall length for extended reach Shaft Ø 19 mm for rigid support Compatible with cutters with 17.7 mm opening Longer reach without compromising rigidity Extending cutter reach can often lead to vibration and loss of accuracy; this extension is engineered to avoid that. With a 150 mm overall length and a substantial shaft diameter of 19 mm, the bar provides added reach while maintaining lateral stability on the spindle. The design reduces deflection compared with slimmer extensions, so machining cycles remain predictable. In practice, this means fewer scrap parts and more consistent surface finish when working on longer or recessed profiles. Secure seating and consistent concentricity A precision M10 thread and a long taper of 30 mm on the seating section ensure that the cutter seats accurately and remains concentric under load. The mating opening of 17.7 mm is specified to match common screw-in cutter geometries, enabling a firm mechanical engagement that supports repeatable runout figures. For toolroom planners and production engineers, this translates into reliable radial control and reduced need for frequent re-adjustment during batch runs. Balanced weight and straightforward handling for workshop use Weighing 0.329 kg, the extension keeps spindle load modest while offering the extra length required for specialised operations. The moderate mass assists in maintaining rotational balance, which is advantageous on both high-speed and general-purpose machines. As a component for cutting tool assemblies, the unit helps streamline setups: fewer intermediate holders, more direct positioning and a lower risk of introducing additional error sources during assembly. For secure extended-reach milling applications, contact Metav Werkzeuge to discuss the Teknik Cutting Tools extension VT506TM and confirm compatibility with existing toolholders; Metav Werkzeuge provides fast, localised supply from Emmerich and practical advice for integration. Technical data Article number: VT506TM Manufacturer: Teknik Makina ECLASS: 21189208 ETIM: EC002219 Facts Overall length: 150 mm Shaft diameter: 19 mm Cutter opening (compatible): 17.7 mm Long taper (seating): 30 mm Thread: M10 Weight: 0.329 kg Special features For screw-in milling cutters Long taper seating for secure engagement Engineered for reduced deflection Suitable for workshop and CNC tool assemblies FAQ Is this extension compatible with all screw-in cutters? Compatibility depends on the cutter's mating opening and thread; the VT506TM by Teknik Makina is designed for cutters with a 17.7 mm opening and an M10 thread match What concentricity performance can be expected? When used with correctly matched screw-in cutters and a properly torqued M10 connection, the extension VT506TM delivers stable concentricity suitable for many finishing and profiling tasks Can the extension be used on high-speed spindles? The VT506TM’s 19 mm shaft and balanced mass of 0.329 kg support use on higher spindle speeds, provided the machine tool and holder meet the required balance and runout specifications How is the extension installed and secured? The component fits via the M10 thread and seats on a 30 mm taper; correct tightening and verification of seating ensure reliable engagement for routine machining Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of extended reach, a secure M8 connection and a lightweight, workshop-ready design to keep machining processes efficient and reliable; order the extension directly via Metav Werkzeuge or consult our specialists for application guidance. Extension for Screw‑in Cutters VT501TM – M8 threaded arbor, 150 mm overall length (Teknik Makina) The Extension for Screw‑in Cutters is a threaded arbor extension designed to increase reach for screw‑in milling cutters in workshop and CNC environments. M8 thread for secure connection 150 mm overall length for extended reach 15 mm shank for standard toolholders Low weight 0.202 kg for balanced handling Extended reach while maintaining rigidity The arbor extension provides an additional 150 mm of overall length without compromising on rigidity. With a 15 mm shank, the extension is compatible with many common toolholders, enabling longer overhangs where access is restricted. This reduces the need for special long‑reach cutters and simplifies setups, allowing precise machining in deep or awkward positions while maintaining acceptable run‑out and stability for milling operations. Threaded seating for repeatable accuracy A secure M8 threaded connection and a 30 mm taper seating ensure a repeatable mechanical interface between the extension and screw‑in cutters. The tapered seating promotes concentric clamping and reduces micro‑movement under load, which translates into consistent tool performance and predictable surface finish. For users unfamiliar with tapered fittings: the cone creates a tight mechanical contact that centres the cutter and resists loosening during rotation. Balanced handling and quick integration Weighing 0.202 kg, the extension remains light enough to avoid excessive imbalance on high‑speed spindles while providing meaningful reach. Its geometry supports straightforward integration into existing tooling systems: the larger shank diameter offers mechanical stiffness, and the reduced mass compared with longer adaptors helps to limit spindle strain. Compatibility with standard holders reduces changeover time and simplifies stock management in mixed production environments. Practical productivity gains for workshops By using this threaded arbor extension, setups become more versatile: one arbor can serve multiple screw‑in cutters, cutting down on the number of specialised tools required. The result is fewer tool changes, reduced inventory complexity and faster turnaround on small to medium production runs. Combined with Metav Werkzeuge’s reliable supply chain and technical support from the Emmerich hub, this extension supports continuous workshop operation and gives buyers confidence in consistent product quality. Contact Metav Werkzeuge for tailored advice on Teknik Makina extensions and secure procurement from our Emmerich hub; technical consultants are available to discuss compatibility and ordering. Technical data SKU: VT501TM Manufacturer: Teknik Makina eClass: 21189208 ETIM: EC002219 Facts Shank diameter: 15 mm Cutter opening diameter: 12.7 mm Cone/taper length: 30 mm Overall length: 150 mm Weight: 0.202 kg Thread: M8 Special features Threaded arbor extension for screw‑in cutters Suitable for workshop and CNC applications Lightweight design for reduced spindle load Standard interface dimensions for common toolholders FAQ Is this extension compatible with standard screw‑in milling cutters? Yes. The Extension for screw‑in cutters (VT501TM) uses an M8 threaded connection and a 12.7 mm cutter opening diameter compatible with common screw‑in milling cutters from typical suppliers. How does the tapered seating affect accuracy? The 30 mm taper seating centres the cutter and increases clamping stability; this design improves concentricity and helps maintain consistent run‑out during milling. Will the weight impact spindle balance at high speeds? At 0.202 kg the extension is intentionally light to minimise imbalance; however, users should always check total assembly balance for very high spindle speeds and perform dynamic balancing if required. Can this arbor extension reduce the need for long‑reach cutters? Yes. By extending reach by 150 mm while keeping a rigid 15 mm shank, the extension allows standard cutters to access deeper features, reducing the necessity for a larger set of specialised long‑reach tools. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of an extended, stable tool connection that improves accessibility in deeper cuts while keeping spindle load low; the M8 thread and 150 mm reach combine to deliver a reliable, repeatable mounting for screw-in indexable cutters. Order directly via Metav Werkzeuge or consult the technical team for selection and supply. Extension for screw-in cutters — 150 mm reach, M8 thread (Teknik Makina) Extension for screw-in cutters for use with screw-in indexable insert cutters, designed to extend working reach while maintaining concentricity and simple mounting 150 mm overall length for deeper reach M8 thread for secure screw-in connection 15 mm solid shaft for rigid support 12.7 mm opening for standard insert cutters Longer reach with predictable, machine-friendly performance The extension arbor provides a controlled increase in working distance without sacrificing precision. With an overall length of 150 mm, the unit is engineered to reduce the need for complex fixturing when machining recessed features or tooling fixtures. The solid 15 mm shaft offers stable support, which helps to reduce unwanted vibration and runout during operations, and the relatively low mass of 0.208 kg minimises additional spindle load. For workshop planners and production engineers, this means predictable machining cycles and fewer interruptions caused by tool instability. Secure mounting that keeps repeatability high Threaded connection via the M8 thread ensures a positive mechanical joint to the cutter body and contributes to consistent concentricity across repeated installations. The internal opening of 12.7 mm suits many screw-in indexable cutters and supports straightforward assembly with standard fastening hardware. The 30 mm cone length creates a reliable seating surface for the cutter, translating to repeatable radial and axial positioning. The result is an extension that preserves the original tool geometry and repeatability, reducing scrap rates and setup time. Simple integration into existing tooling systems Designed for practical compatibility, the extension fits into common tool setups for indexable cutters and is particularly useful where increased reach is required without converting to long overhang cutters. The component’s straightforward geometry permits quick verification of fit and alignment on the bench; the absence of complex adapters means fewer parts to manage in inventory. This practical design supports leaner tool management and faster changeovers in small-batch or mixed-production environments. Durable, production-oriented specification Although detailed material specifications are not supplied in the product data, the component’s dimensions and thread standardisation reflect a production-orientated mindset: standardised thread (M8), defined seating cone length (30 mm) and a measured shaft diameter (15 mm). These measurable parameters allow engineering teams to assess stiffness and dynamic behaviour in context with machine and cutter characteristics. Where higher rigidity or specific coatings are required, the extension can be evaluated alongside suitable cutter bodies to ensure compatibility with the intended machining task. For procurement or technical advice on Teknik Makina extensions: contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 to confirm fitment and secure supply from Emmerich Technical data Article number: VT500TM Manufacturer: Teknik Makina Facts Overall length: 150 mm Shaft diameter: 15 mm Opening for screw-in cutter: 12.7 mm Cone length (seating): 30 mm Thread: M8 Weight: 0.208 kg Special features For screw-in indexable cutters Simple, standardised connection Low additional spindle mass Designed for repeatable mounting FAQ Which cutter types are compatible with this extension? The extension for screw-in cutters (VT500TM) is intended for screw-in indexable insert cutters; compatibility is determined by the cutter’s 12.7 mm mounting opening and M8 screw connection. How does the M8 thread affect mounting stability? The M8 thread used on the Technik Makina extension (VT500TM) provides a secure mechanical connection that contributes to repeatable seating and reduced axial movement during machining. What are the key dimensions to check before fitting? Confirm the cutter’s mounting opening (12.7 mm), the machine-side holder clearance for a 150 mm overhang, and the 15 mm shaft diameter to ensure correct fit and stiffness with the selected cutter body. Will the extension significantly increase spindle load? With a weight of 0.208 kg, the extension adds minimal mass; assessment should still be made in context with the spindle speed and cutter mass to maintain dynamic stability during operation. Can the extension be used with different brands of indexable cutters? The extension (VT500TM) is compatible with cutters that match the listed mounting dimensions and an M8 thread; cross-brand fit should be verified by checking the cutter’s mounting geometry. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of precise fit, extended reach and solid connection for reliable milling operations. The extension’s 24 mm shank and M12 thread ensure consistent clamping and minimal runout, supporting smoother production. Order the extension directly via Metav Werkzeuge or consult the specialists for application advice. Extension for Screw-in Milling Cutter VT513TM — 24 mm shank, M12 thread (Teknik Makina) The Extension for Screw-in Milling Cutter is a tool extension designed to increase reach and maintain secure seating for screw-in cutters in milling and CNC applications. Solid 24 mm shank diameter M12 thread connection for secure attachment 150 mm overall length for extended reach 40 mm taper for tight cutter seating Extend reach while keeping rigidity and control The extension delivers a balance between reach and stiffness: with a 24 mm shank and a 150 mm overall length, the component provides increased access to recessed features while aiming to preserve tool stability. Longer tool extensions often risk vibration and loss of precision; the measured shank diameter here reduces that risk by maintaining a robust connection to the spindle or holder. This makes the accessory suitable where additional length is required without sacrificing repeatable performance. Reliable cutter seating and repeatable connection Designed for screw-in cutter systems, the tool features an M12 thread, a 20.7 mm cutter opening and a 40 mm taper for the mating cutter. The combination of thread and taper distributes clamping forces and supports axial alignment, which contributes to secure clamping and reduced runout compared with loose-fit adapters. The taper length enhances axial stability during milling, explaining why a properly matched extension can help preserve cutting geometry and surface finish in precision operations. Workshop compatibility and practical handling With a compact weight of 0.502 kg and straightforward geometry, the extension integrates into standard workshop workflows and CNC tool inventories. The accessory is intended for use with screw-in milling cutters and is produced for robust handling in repetitive machining contexts. Technical enquiries and specification checks are supported by Metav Werkzeuge, whose role as a precision partner helps ensure correct selection and a reliable supply chain for production and maintenance demands. Contact Metav Werkzeuge for tailored advice on integrating the Teknik Makina VT513TM extension into existing tooling setups and to discuss availability or delivery options Technical data Article number: VT513TM Manufacturer: Teknik Makina Product name: Extension for screw-in milling cutter Facts Shank diameter: 24 mm Cutter opening diameter: 20.7 mm Taper length (screw-in cutter): 40 mm Overall length: 150 mm Thread: M12 Weight: 0.502 kg Special features Intended for screw-in milling cutters M12 thread connection 40 mm taper for cutter seating Compact, workshop-friendly weight FAQ What shank diameter does the extension use? The extension is supplied with a 24 mm shank diameter, suitable for holders and collets designed for this dimension. Which thread and taper specifications are provided for cutter mounting? The VT513TM uses an M12 thread, a 20.7 mm cutter opening and a 40 mm taper to seat screw-in cutters securely. What is the overall length of the extension? The overall length is 150 mm, offering extended reach for machining deeper or recessed areas. How heavy is the extension and is it easy to handle? The extension weighs 0.502 kg, a compact mass that supports easy handling and practical workshop use. For which applications is this extension intended? The extension is intended for milling and CNC operations requiring increased tool reach with screw-in cutter systems. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a tool that combines precise compatibility with APKT 1705 indexable inserts and a robust 32 mm shank for stable machining; order the cutter directly via Metav Werkzeuge or consult our specialists for integration advice. Shank cutter S664TM — Shank cutter for APKT 1705 indexable inserts, Ø 40 mm, 4 flutes The Shank cutter S664TM is a precision milling head engineered for use with APKT 1705 indexable inserts, designed to deliver stable, repeatable results in indexable-insert milling applications. Four cutting edges for efficient material removal Diameter 40 mm for stable machining 32 mm shank for secure clamping Compatible with APKT 1705 indexable inserts Stable, vibration‑resistant clamping for consistent part quality The combination of a 32 mm shank and an outer diameter of Ø 40 mm gives the tool a high moment of inertia, which reduces chatter and improves surface quality in interrupted and continuous cuts. With an overall length of 150 mm and a cutting length of 60 mm, the design balances reach and rigidity to support predictable toolpaths and repeatable geometries. The tool’s mass of 0.85 kg contributes to stability without compromising handling during tool changes. These dimensional characteristics translate into fewer rejected parts and a steadier process window, so cycle times can be optimised with confidence. Fast, secure insert changes minimise downtime Insert retention is achieved with a standard M4x10 Torx screw tightened with a T15 key, enabling swift and reliable replacement of worn cutting edges. The indexable system accepts APKT 1705 inserts, a widely used insert format that keeps tooling costs down by allowing multiple cutting edges per insert. The straightforward fastening method reduces maintenance time at the machine and simplifies inventory: fewer complete cutters are required because inserts can be rotated or replaced independently. This arrangement supports efficient shift‑turnover procedures and lowers the mean time to repair in busy production environments. Predictable performance and straightforward integration into tooling stocks With four cutting edges, the cutter offers balanced engagement and even chip distribution for many common milling operations where APKT insert geometry is appropriate. Compatibility with inserts from established suppliers such as Taegutec ensures easy sourcing and replacement. The tool’s geometry and standardised fastening mean it can be integrated into existing toolholders and workflows without bespoke adaptations. For procurement and toolroom planning, the clear specifications — diameter, shank size, cutting length and Torx screw type — make lifecycle calculation and spare‑parts management straightforward, supporting lean stock strategies and reliable supply. Contact Metav Werkzeuge to discuss technical fitment, availability and supply options for the Teknik Makina S664TM shank cutter compatible with APKT 1705 indexable inserts Technical data Article number: S664TM Manufacturer: Teknik Makina Type: Shank cutter for APKT 1705 indexable inserts Dimensions & weight Diameter: 40 mm Shank diameter: 32 mm Cutting length: 60 mm Overall length: 150 mm Weight: 0.85 kg Number of cutting edges: 4 Compatibility & fittings Compatible inserts: APKT 1705 Compatible insert manufacturer: Taegutec Torx screw: M4x10 Torx key: T15 FAQ Which insert format is required for this cutter? The shank cutter accepts APKT 1705 indexable inserts; the tool is supplied to work with that insert format for easy sourcing. How are inserts secured in the cutter? Inserts are clamped with an M4x10 Torx screw tightened using a T15 key, allowing fast and secure insert changes. What are the key dimensions to consider when planning toolholders? Important dimensions are Ø 40 mm diameter, 32 mm shank diameter, 60 mm cutting length and 150 mm overall length; the cutter weighs 0.85 kg. Is the cutter compatible with Taegutec inserts? Yes, the cutter is compatible with APKT 1705 inserts from manufacturers such as Taegutec, facilitating straightforward replacement. What machining advantages does the indexed system provide? The indexable design of the cutter reduces tooling cost per cutting edge and shortens downtime for maintenance, making it suitable for operations where predictable tool costs and rapid insert changes are priorities. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a robust milling solution that combines a 40 mm diameter, four cutting edges and a 60 mm cutting length for efficient material removal and consistent surface finish; order the cutter directly via Metav Werkzeuge or consult our technical team for application advice. Shank milling cutter S469TM – 40 mm diameter, 4 flutes (Teknik Makina) The Shank milling cutter S469TM is designed for indexable-insert milling with ADMT 1606 inserts, offering a rigid shank layout for stable, repeatable operations in production and workshop environments 40 mm cutting diameter Four cutting edges for consistent removal Shank 32 mm for increased rigidity Compatible with ADMT 1606 Walter inserts Greater metal removal with stable cutter geometry With a 40 mm diameter and four flutes, the tool provides a combination of chip removal rate and surface control that suits continuous milling operations. The 60 mm cutting length delivers extended engagement for shoulder and face milling while the 90° cutting angle ensures a predictable corner geometry. The indexable-insert concept reduces toolholding variability: individual inserts are clamped to a precise seat so the overall tool runout remains low, which in turn secures surface quality and extends effective tool life. This measurable setup translates into fewer interruptions and a more reliable production rhythm. Fast insert changes and secure clamping reduce downtime A robust Shank Ø 32 mm gives the assembly high torsional stiffness in the holder, improving chatter resistance under elevated cutting forces. Insert retention is via an M4x10 Torx screw operated with a T15 key, a standardised solution that balances torque transmission with quick serviceability. The screw system allows repeatable clamp preload for each replacement insert, meaning maintenance intervals are predictable and changeovers are efficient. Using industry-standard indexable inserts such as ADMT 1606 keeps spare-part logistics simple and supports fast on-machine recovery. Designed for workshop and production reliability At an overall length of 150 mm and a weight of 0.927 kg, the cutter is dimensioned for stable handling and compatibility with common milling arbors. Compatibility with Walter-type ADMT 1606 inserts supports cross-sourcing flexibility, while the solid construction from Teknik Makina addresses the need for dependable, everyday performance. The tool's design focuses on reducing total machining cost by combining replaceable cutting edges with a durable shank, which lowers the cost per cutting edge and simplifies inventory management in a centralised workshop environment. For reliable high-performance milling with ADMT 1606 inserts, request availability or technical clarification from Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: S469TM Manufacturer: Teknik Makina Designation: Shank milling cutter for ADMT 1606 indexable inserts Facts Diameter: 40 mm Shank diameter: 32 mm Cutting length: 60 mm Overall length: 150 mm Cutting edges: 4 Weight: 0.927 kg Cutting angle: 90° Special features Compatible with ADMT 1606 indexable inserts (Walter) Torx screw M4x10, Torx key T15 SKU: S469TM FAQ What insert type does the cutter use? The cutter accepts ADMT 1606 indexable inserts; the tool is supplied as a shank milling cutter compatible with Walter-style ADMT 1606 inserts. How is the insert secured on the tool? Inserts are fastened with an M4x10 Torx screw tightened using a T15 key, providing repeatable clamping force and quick changeover for the S469TM shank milling cutter. Is the shank suitable for heavy milling operations? The S469TM has a 32 mm shank diameter that improves rigidity and reduces the risk of chatter, making the tool suitable for demanding milling tasks in production settings. What are the key dimensions to check for holder compatibility? Relevant dimensions are the 40 mm cutting diameter, 32 mm shank diameter and 150 mm overall length; these determine fitment in standard arbors and toolholders. Who manufactures this milling cutter? The cutter is produced by Teknik Makina and distributed via Metav Werkzeuge as SKU S469TM for industrial and workshop use. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of 32 mm blade height and a 2.45 mm narrow cutting width for precise, repeatable parting operations; the robust 150 mm length ensures stable clamping and reduced vibration. Order the parting blade directly via Metav Werkzeuge or consult our application specialists for tailored advice. Parting blade KL44TM by Teknik Makina — 32 mm height, 150 mm length The parting blade KL44TM is a lathe parting (cut-off) blade designed for accurate, low-waste separation and grooving operations in production and workshop environments Compatible with Korloy SP 300 inserts 32 mm blade height for stable clamping 2.45 mm narrow blade for fine parting cuts 150 mm overall length for secure mounting Engineered for precise parting with stable clamping The KL44TM is developed for reliable parting and cut-off performance where repeatability matters. With a 32 mm height the blade offers an increased clamp surface that significantly reduces the risk of chatter during plunge cutting; this leads to cleaner parting edges and less rework. The slim 2.45 mm width minimises material loss and lowers cutting forces, which in turn reduces spindle load and extends insert life. These measurable characteristics support predictable cycle times and make the tool a suitable choice for small-batch production as well as series work. Compatibility that streamlines machining processes Designed to accept SP 300 style inserts from Korloy, the KL44TM gives shops a simple route to standardised tooling and quick insert swaps. The use of a common insert family shortens downtime for changes and inventory management while enabling stable cutting conditions with proven grades. Because the blade matches established insert interfaces, setup is straightforward and fixturing remains consistent across different workpieces — a practical advantage for lean workflows and mixed-machine shops aiming to cut changeover time. Practical integration for workshop reliability In everyday workshop contexts the combination of a 150 mm overall length and the reinforced blade height supports secure mounting in most parting tool holders, improving operator confidence and reducing the need for repeat adjustments. The blade is positioned within the cutting-tools category for turning and cut-off tasks and pairs well with medium to heavy-duty lathes. For technical queries or specific application data Metav Werkzeuge provides documentation and advisory support, helping to select suitable inserts and verify machine compatibility before purchase. For reliable, low-waste parting operations request technical advice from Metav Werkzeuge regarding the Teknik Cutting Tools KL44TM — contact info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for individual lathe setups Technical data Article number: KL44TM Product name: Parting blade Manufacturer: Teknik Cutting Tools / Responsible: Metav Werkzeuge GmbH Compatible insert family: SP 300 Compatible insert maker: Korloy Core specifications Blade height: 32 mm Cutting height: 25 mm Blade width: 2.45 mm Overall length: 150 mm SKU: KL44TM Special features Tool type: Parting blade (cut-off) Insert compatibility: Korloy SP 300 Designed for stable clamping and narrow-parting cuts FAQ What inserts fit this parting blade? The KL44TM is designed for SP 300 style inserts and is compatible with Korloy insert versions in that family. Which lathe operations are suitable for this blade? This parting blade is intended for cut-off and grooving operations on conventional and CNC lathes where a narrow cutting width and stable clamping are required. How does the blade height affect performance? A 32 mm blade height increases clamp support and reduces vibration, improving edge quality and extending insert life during plunge cuts. Is the KL44TM suitable for high-speed parting? The KL44TM is optimised for stable parting; suitability for high-speed regimes depends on insert grade and machine capability — matching the SP 300 insert grade to the application improves results. Can this blade reduce material waste? Yes; the 2.45 mm narrow width minimises the kerf, lowering material loss per cut while maintaining cutting stability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from the combination of a 32 mm blade height and a narrow 2.45 mm cutting edge for accurate, efficient parting; order the KL35TM through Metav Werkzeuge or ask our specialists for tailored application advice. Teknik Makina KL35TM parting blade — 32 mm height, 150 mm length Teknik Makina KL35TM parting blade designed for grooving and parting operations in precision turning applications, compatible with KGMN 300 indexable inserts. 32 mm blade height for deep grooving 2.45 mm narrow blade for precise parting Fits Korloy KGMN 300 indexable inserts 150 mm overall length for stable clamping Precision for demanding grooving operations The Teknik Makina KL35TM parting blade offers a reliable geometry tailored to consistent cut control. With a 32 mm blade height and a 25 mm cutting height, the tool provides a stable reference for axial positioning, which reduces chatter and improves surface finish. The narrow 2.45 mm blade width minimises material waste during parting and enables fine, accurate separations on small-diameter workpieces. These dimensional specifications are intended to support repeatable setups and shorter cycle times in production environments where precision is essential. Seamless compatibility with indexable inserts and holders Compatibility with established insert systems is a practical advantage. The blade is specified for use with KGMN 300 indexable inserts from Korloy, allowing well-known insert geometries and grades to be chosen according to material and cutting conditions. The design also matches clamping holders with a max. cutting depth 36 mm, which permits secure installation and full exploitation of the blade’s height. Using standardised inserts simplifies tool management, reduces retooling time and makes it straightforward to select coatings or grades for specific metals without changing the blade geometry. Robust geometry that supports efficient machining A 150 mm overall length provides sufficient reach and lever arm for stable clamping while keeping the unsupported length moderate to limit deflection. The blade’s proportions promote efficient chip flow and reduce the risk of jamming during deep cuts. Built for workshop resilience, the geometry is compatible with common turning setups and can be integrated into existing toolholding systems. The result is a balance between rigidity and accessibility: operators benefit from reliable parting actions and reduced tool-change frequency, which contributes to smoother production schedules. Practical advantages for procurement and workshop planning Selecting standardised components streamlines inventory and maintenance. The blade’s fit with Korloy’s KGMN 300 inserts means tooling can be standardised across multiple machines, lowering stock variety and simplifying reordering. Technical teams will value the clearly defined dimensions — 32 mm blade height, 25 mm cutting height, 2.45 mm blade width, 150 mm length — which support accurate fixture design and repeatable setups. This clarity reduces downtime caused by mis-matched components and supports predictable manufacturing throughput. For a reliable supply from our Emmerich hub and expert application guidance on the KL35TM, contact Metav Werkzeuge to discuss which Korloy insert grades best suit the intended materials and cycle times Technical Data Article number: KL35TM Manufacturer: Teknik Makina Facts Blade height: 32 mm Cutting height: 25 mm Blade width: 2.45 mm Overall length: 150 mm Max. stechtiefe (holder): 36 mm Special features Compatible with Korloy KGMN 300 indexable inserts Designed for grooving and parting operations Suited to standard clamping holders FAQ What inserts are compatible with this parting blade? The KL35TM parting blade is compatible with Korloy KGMN 300 indexable inserts and accepts standard insert geometries for grooving and parting. What are the key dimensions to check before installation? Check the 32 mm blade height, 25 mm cutting height, 2.45 mm blade width and the 150 mm overall length to ensure correct alignment in the holder. Which maximum cutting depth is supported by the holder interface? The blade is designed to work with clamping holders that permit a max. cutting depth of 36 mm. Is the blade suitable for use with standard turning toolholders? Yes, the KL35TM is intended for integration with standard clamping holders compatible with KGMN 300 inserts and typical grooving setups. How does the narrow blade width benefit production? A 2.45 mm blade width reduces material loss during parting and allows finer separations, which is advantageous for precision components and material-saving processes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the KL30TM parting blade’s precise 25 mm cutting height together with its slim 2.45 mm blade width for clean, repeatable parting cuts; order the KL30TM directly via Metav Werkzeuge or ask our consultants if needed. Parting Blade KL30TM — 25 mm cutting height, 2.45 mm blade width (Teknik Makina) The Parting Blade KL30TM is a robust parting bar for lathe and CNC applications, designed to accept MGMN 300 indexable inserts and deliver stable parting operations across short to medium depth cuts Precision 25 mm cutting height 2.45 mm slim blade for narrow cuts 150 mm overall length for stability Compatible with MGMN 300 inserts Reliable parting performance for production lathes The KL30TM offers a consistently controlled cutting geometry that reduces vibration and improves surface finish when parting-off components. With a 25 mm cutting height and a total length of 150 mm, the bar provides the necessary overhang and rigidity for many workshop and light industrial turning tasks. The relatively narrow 2.45 mm blade width enables narrow kerf cuts, which minimise material waste and shorten chip evacuation times. Combined, these dimensions help to maintain cycle times and reduce the need for secondary machining, delivering an efficient production flow. Precision geometry that reduces rework and scrap A narrow blade and defined cutting height ensure reliable insert positioning and repeatable results. The KL30TM is sized for MGMN 300 type indexable inserts — a standard insert format that allows quick replacement and consistent edge geometry without the need to regrind. Using indexable inserts means downtime is limited to fast insert changes, which lowers overall production costs and increases machine availability. The tool’s geometry supports clean break-off of workpieces, reducing burr formation and the risk of rework. Easy integration and practical workshop benefits Installation is straightforward in standard parting tool holders; the design supports a maximum parting depth of 36 mm when used with compatible clamping systems. Compatibility with established insert types and references such as N151-3 (as listed) and inserts from Korloy simplifies procurement and inventory management. For workshops aiming to centralise tool supply, the KL30TM fits into common machining setups without complex adaptations, helping to streamline tooling logistics and maintain predictable production results. Contact Metav Werkzeuge for tailored advice on the Teknik Makina KL30TM parting blade — call +49 2822 7131930 or email info@metav-werkzeuge.com to request technical details and fast supply from Emmerich. Technical Data SKU: KL30TM Manufacturer: Teknik Makina ECLASS: 21181018 Suitable inserts manufacturer: Korloy Numbers / Core technical data Blade height: 32 mm Cutting height: 25 mm Blade width: 2.45 mm Overall length: 150 mm Maximum parting depth (with suitable clamping): 36 mm Special features / Versions Compatible insert type: MGMN 300 Reference insert types mentioned: N151-3 Story trigger / listing reference: stechschwert FAQ Is the KL30TM compatible with Korloy MGMN 300 inserts? Yes. The KL30TM parting blade is specified for use with MGMN 300 indexable inserts and is listed for compatibility with Korloy insert types. What are the main dimensions of the parting blade? The KL30TM provides a blade height of 32 mm, a cutting height of 25 mm, a blade width of 2.45 mm and an overall length of 150 mm. How deep can the KL30TM cut? When mounted in a suitable clamping holder, the parting blade supports a maximum parting depth of 36 mm (clamping system dependent). Which insert references appear with this blade? The product listing references MGMN 300 inserts and includes the insert reference N151-3 as shown in the item listing. For what kinds of turning operations is this blade suitable? Designed as a parting tool, the KL30TM is suitable for controlled parting-off and narrow-groove operations on lathes and CNC turning centres that accept standard parting holders and MGMN-style indexable inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Efficient parting operations are achieved with a 2.45 mm blade width and a 25 mm cutting height, combined with a 150 mm overall length for stable clamping and consistent chip control; order the KL60TM parting blade directly via Metav Werkzeuge or consult the advisors for integration help. KL60TM Parting Blade — 2.45 mm blade width, 150 mm length (Teknik Makina) KL60TM Parting Blade is a precision parting tool for CNC turning, engineered to work with Sandvik inserts (type 123 3C) and to deliver reliable cut-off performance in production environments Compatible with Sandvik 123 3C inserts Narrow 2.45 mm blade width for fine kerfs 150 mm overall length for secure clamping Consistent cut quality from optimised geometry The design focuses on a slim kerf and steady support to reduce vibration and minimise workpiece distortion. The 2.45 mm blade width and 25 mm cutting height ensure a narrow chip formation, which helps maintain surface integrity during separation. For workshop planners this means fewer rejects and improved process repeatability thanks to the blade’s balanced proportions and predictable cutting behaviour. Stable clamping and reduced chatter for safer cycles A longer body aids rigidity at the toolholder, so the 150 mm length and 32 mm overall height contribute to a firm seating in standard clamping systems. The resulting stability reduces chatter and tool deflection, allowing for more consistent parting passes and extended insert life. This translates directly into shorter setup times and less downtime between operations, supporting a smoother production flow. Compatibility that simplifies tooling logistics Prepared for use with Sandvik inserts (designation 123 3C), this parting blade aligns with established insert standards to simplify reordering and tool stocking. The compatibility with widely used insert systems means existing holders and inventory can be retained while upgrading to a purpose-built blade. The KL60TM therefore supports efficient procurement and quick integration into existing turning centres. Practical advantages for everyday workshop use The parting blade’s dimensions balance accessibility for close-to-shoulder cuts with a robust contact area for the toolholder, improving handling during mounting and reducing the risk of misalignment. The combination of narrow blade width and defined cutting height supports precise kerf control and easier separation of finished components, helping to maintain output quality across batches while keeping process control straightforward. Discuss the KL60TM parting blade by Teknik Makina with Metav Werkzeuge for tailored parting solutions — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: KL60TM Manufacturer: Teknik Makina Facts Overall length: 150 mm Blade height: 32 mm Cutting height: 25 mm Blade width: 2.45 mm Special features Compatible with Sandvik Suitable for insert type 123 3C Parting blade for CNC turning FAQ Which insert type fits this blade? The KL60TM parting blade is specified for use with Sandvik inserts, type 123 3C, enabling straightforward replacement and stocking. What are the main dimensions of the blade? Key dimensions for the KL60TM are 150 mm overall length, 32 mm height, 25 mm cutting height and a 2.45 mm blade width. Is the blade suitable for standard insert holders? Yes, the KL60TM is designed for compatibility with common insert systems and works with Sandvik-compatible holders for seamless integration. How does the narrow blade width benefit production? A 2.45 mm blade width reduces kerf size and chip volume, promoting cleaner separations and less material distortion during parting operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of 32 mm blade height and 25 mm effective cutting height for reliable, repeatable parting operations; the 150 mm length provides reach for deeper cuts while keeping rigidity. Order the parting blades directly via Metav Werkzeuge or ask our consultants if further data is required. Parting blades KL80TM – 32 mm blade height, 150 mm length (Teknik Makina) Parting blades KL80TM are precision cut-off blades engineered for lathe parting and grooving, offering stability and consistent cutting geometry for production and workshop environments. 32 mm blade height for stable cutting 150 mm overall length for deeper cuts 25 mm effective cutting height Deliverable accuracy for repeatable production results Precision in parting operations begins with stable geometry. The 32 mm blade height increases section resistance to bending, which improves cutting stability and reduces the need for frequent rework. For series production, this means more consistent part lengths and fewer rejects. The measurable blade dimensions provide a clear baseline for process planning and help to maintain cycle-time targets in turning and finishing workflows. Reduced vibration and improved surface quality through rigid design A taller cross-section and solid profile translate into lower tool deflection during cut-off operations. The result is improved surface quality on the parted face and fewer secondary operations. By maintaining a rigid cutting edge, the tool supports higher feed rates without compromising finish, contributing to an efficient turning process and reduced machining time per component. Fast integration into existing tooling stocks The blade’s proportions and standardised geometry allow straightforward fitting in common parting tool holders. Minimal setup and predictable clamping behaviour speed up tool changes and reduce machine downtime. This practical compatibility supports lean workshop practices and helps to maintain continuity across shifts when multiple operators use the same machine fleet. Consistent performance across routine turning tasks With an effective cutting height of 25 mm and an overall length of 150 mm, the blade balances reach and stiffness for everyday cut-off and grooving tasks. The dimensions suit both single-machine shops and production cells where predictable, repeatable performance is required. Manufactured by a recognised supplier, the component meets expectations for durability and repeatability in regular service. For procurement or technical clarification, contact Metav Werkzeuge to discuss stocking, compatibility or to request additional data relevant to specific machining setups. Technical data Article number: KL80TM Eclass: 21181018 Facts Blade height: 32 mm Overall length: 150 mm Cutting height: 25 mm Special features Product type: Parting blades Manufacturer: Teknik Makina UID: KL80TM FAQ What are the exact dimensions of the parting blade? The Parting blades KL80TM have a blade height of 32 mm, an overall length of 150 mm and an effective cutting height of 25 mm (SKU KL80TM). For which operations is this blade intended? The KL80TM from Teknik Makina is designed for lathe parting and cut-off operations, suitable for routine grooving and separating tasks in turning processes. Can the blade be used in standard parting holders? Yes, the KL80TM is intended for use with common parting tool holders; correct clamping and alignment ensure the best performance. How does the blade geometry affect machining results? The increased blade height and rigid profile of the KL80TM reduce deflection and vibration, which improves surface finish and dimensional repeatability during parting. Is additional technical documentation available? Technical specifications and detailed dimension sheets for the Parting blades KL80TM can be provided on request to support process setup and holder selection. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of robust parting geometry, 32 mm blade height and a 150 mm overall length for stable, repeatable parting. The KL81TM delivers consistent cutting performance and reduced rework; order the parting blades directly via Metav Werkzeuge or consult the technical team for holder compatibility and delivery options. Stechschwerter – Parting blades, 32 mm height, 150 mm length (Teknik Makina) Stechschwerter are precision parting blades designed for reliable material separation in turning operations, suited to standard holders and industrial workshop environments. Robust parting geometry 32 mm blade height for deep cuts 150 mm overall length for stability Compatible with standard holders Consistent cuts through stable geometry and clear cutting height The solid design of these parting blades provides a predictable cutting line and reduced vibration during separation. With a 32 mm blade height and a 25 mm cutting height, the tool enables deeper parting strokes while maintaining precision and surface quality. The increased height enhances lever arm stability, which reduces chatter and the likelihood of workpiece deformation. For technicians and production planners, this translates into fewer rejects and less time spent on secondary machining, supporting higher first-pass yield. Simple integration into existing setups for faster throughput Designed for compatibility with conventional parting holders, the KL81TM simplifies tool changeovers and keeps machine downtime to a minimum. The 150 mm overall length contributes to improved clamping stability without requiring special fixtures. As a result, the blades are suitable for retrofitting into established workflows, enabling a rapid increase in throughput. Clear, standardised dimensions make programming and process validation straightforward, so line engineers can rely on predictable cycle times and maintain process control. Reliable supply chain and service that supports production continuity Sourced from Teknik Cutting Tools and distributed via Metav Werkzeuge, these parting blades come with the assurance of a quality-focused supply network. Metav’s European logistics hub functions as a quality filter, ensuring ordered items meet expected specifications and arrive ready for immediate use. For procurement managers, the benefit is a dependable partner that reduces supplier complexity and supports uninterrupted production planning with transparent order processing and stock handling. For specification advice, holder compatibility checks or to request delivery from Metav Werkzeuge’s Emmerich hub, contact the Metav technical team by e‑mail or phone for prompt, expert support and fast supply. Technical Data Article number: KL81TM Product: Parting blades (Stechschwerter) Brand: Teknik Makina ECLASS: 21181018 Dimensions Blade height: 32 mm Overall length: 150 mm Cutting height: 25 mm Special features Suitable for parting operations Compatible with standard parting holders SKU: KL81TM FAQ What materials are suitable for these parting blades? The Stechschwerter parting blades (Teknik Cutting Tools KL81TM) are intended for general parting applications; specific material suitability should be checked against the machine and holder being used. Is the KL81TM compatible with standard parting tool holders? Yes. The KL81TM is dimensioned for standard holders and offers a 150 mm overall length to support stable clamping in conventional setups. How does the cutting height affect operation? A 25 mm cutting height on these parting blades helps to achieve deeper cuts with reduced risk of workpiece deformation, improving process reliability and finish quality. Can these blades reduce machining time? By providing stable geometry and predictable cutting behaviour, the KL81TM can contribute to fewer stoppages and rework, which supports improved throughput in turning operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine the 3.45 mm narrow blade with a 32 mm shank height and 150 mm overall length to achieve stable, precise parting and grooving results in series production. Order the part directly via Metav Werkzeuge or consult the technical team for integration advice. Parting Blade KL45TM by Teknik Makina — 3.45 mm blade, 150 mm length A sturdy parting tool blade, the Parting Blade KL45TM is designed for precision grooving and parting operations with Korloy SP 400 indexable inserts. Parting tool for Korloy SP 400 inserts 3.45 mm narrow blade for fine kerf 32 mm shank height for enhanced rigidity 150 mm overall length for extended reach Precise cuts with a narrow kerf and solid support The combination of a 3.45 mm blade width and a 25 mm cutting height creates a consistently narrow kerf that minimises material loss and reduces the need for secondary finishing. A 32 mm shank height provides the necessary stiffness to resist chatter during aggressive feeds, which means cleaner parting lines and more predictable dimensional results. In practice, a narrow blade reduces cutting forces and, when paired with a rigid holder, contributes to longer tool life and fewer rejected parts. Plug-and-produce compatibility to keep production moving Compatibility with Korloy SP 400 indexable inserts ensures straightforward procurement and rapid replacement cycles. The use of standardised inserts promotes interchangeability across different machines and fixtures, shortening downtime during tool changes. For manufacturers focused on throughput, this standard compatibility translates into measurable improvements in line availability and reduced inventory complexity while maintaining consistent cutting performance. Practical dimensions for diverse shop floor setups An overall length of 150 mm offers sufficient reach for a wide range of turning and grooving holders without unnecessary overhang, while the 25 mm effective cutting height accommodates common part geometries. The blade's proportions are optimised for both manual and CNC lathe setups where rigidity and repeatability are priorities. The robust geometry supports steady feeds and aids operators in maintaining process stability, reducing the frequency of in-process adjustments and rework. For reliable parting performance from Teknik Makina, contact Metav Werkzeuge for procurement or technical guidance at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss integration with existing tool holders and inserts. Technical data SKU: KL45TM Manufacturer: Teknik Makina ECLASS: 21181018 Compatible insert manufacturer: Korloy Compatible insert type: SP 400 Core dimensions Blade width: 3.45 mm Shank height: 32 mm Cutting height: 25 mm Overall length: 150 mm Compatibility & features For use with Korloy SP 400 indexable inserts Intended for parting and grooving applications Robust shank geometry for reduced vibration FAQ Which inserts are compatible with this parting blade? The parting blade KL45TM is specified for Korloy SP 400 indexable inserts and is designed to accept that insert form for reliable seating and repeatable performance. What workpiece materials is the blade suited for? The KL45TM blade is intended for general parting and grooving tasks; insert selection (for example grades and coatings) should be matched to the workpiece material to achieve optimal cutting performance. How does the shank height affect machining stability? A 32 mm shank height increases rigidity at the cutting zone, reducing chatter and improving surface finish during parting or grooving cycles. Is the overall length suitable for standard CNC lathe holders? With a 150 mm overall length, the blade provides sufficient reach for most holders while keeping overhang minimal to preserve stability in CNC lathe setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of a 32 mm blade height and 150 mm overall length ensures controlled, rigid parting performance for demanding turning operations; compatibility with ZT.D4C indexable inserts and ZCC inserts reduces changeover time and simplifies tool inventory. Order directly via Metav Werkzeuge or contact their consultants for specification support. Parting blades for ZT.D4C indexable inserts — KL69TM, 32 mm blade height (Teknik Makina) The parting blades for ZT.D4C indexable inserts deliver precise cut-off capability for CNC turning applications and are designed to accept ZCC-standard inserts. Robust 32 mm blade height for stable parting 150 mm overall length for deep cuts Compatible with ZT.D4C indexable inserts Designed for ZCC standard inserts Stable cuts from a tall, rigid blade for repeatable results A tall blade profile with 32 mm blade height gives the assembly enhanced rigidity during parting operations, reducing vibration and chatter and thereby improving surface finish and dimensional repeatability. The 25 mm cutting height specifies the usable insert contact zone and supports consistent chip formation when paired with the correct insert geometry. Such dimensional clarity helps maintenance planning and setup precision, contributing to shorter machining cycles and fewer scrap parts. Easy integration with indexable systems for efficient changeovers Designed specifically for ZT.D4C indexable inserts, the blade simplifies inventory management by matching a common insert family; compatibility with ZCC inserts further broadens replacement options. The 150 mm overall length provides reach for deeper parting tasks without compromising toolholder stability. This configuration aids production planners seeking low-downtime tool solutions and supports rapid insert swaps, keeping throughput high in series turning or batch work. Industrial use cases and supply reliability for workshop operations Suitable for industrial turning and workshop environments where reliable parting or cut-off performance is essential, this blade suits a range of steel-turning tasks when paired with the correct insert choice. The item is supplied under SKU KL69TM, fitting standard toolholders configured for ZT.D4C inserts. Purchasing through Metav Werkzeuge guarantees access to central European distribution and a quality-filtered inventory, which helps maintain consistent supply to the workbench and reduces procurement complexity. Contact Metav Werkzeuge for tailored specification advice and to secure Teknik Makina parting blades directly from Emmerich. Technical data SKU: KL69TM Manufacturer: Teknik Makina ECLASS: 21181018 Dimensions Blade height: 32 mm Overall length: 150 mm Cutting height: 25 mm Compatibility & details For ZT.D4C indexable inserts Compatible insert manufacturer: ZCC Product type: Stechschwerter (parting blades) Label: Stechschwerter ZT.D4C FAQ Which indexable inserts fit this blade? The blade is designed for ZT.D4C indexable inserts and is compatible with ZCC standard inserts when the correct insert grade and geometry are selected. What are the main dimensions of the parting blade (KL69TM)? Key dimensions are 32 mm blade height, 150 mm overall length and 25 mm cutting height for SKU KL69TM. For which operations is this product most suitable? This parting blade is intended for cut-off and parting applications in CNC and manual turning where a rigid blade profile and standard indexable inserts are preferred. Is the blade compatible with ZCC-manufactured inserts? Yes, the design specifies compatibility with ZCC inserts for the ZT.D4C indexable system supplied with SKU KL69TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise, low-waste parting operations thanks to the slim 2.45 mm blade and a robust 150 mm overall length; secure compatibility with DGN 3 indexable inserts ensures repeatable clamping and reliable chip control. Order the parting blade directly via Metav Werkzeuge or consult the team for application advice. Parting blade KL20TM — Parting-off blade with DGN 3 compatibility by Teknik Makina The Parting blade KL20TM is a lathe parting-off blade engineered for clean cut-offs and narrow-kerf grooving in turning operations. Slim 2.45 mm blade width for minimal material loss 150 mm overall length for secure reach in lathes Compatible with DGN 3 indexable inserts Cutting height 25 mm for standard toolholders Precise geometry for consistent parting performance The KL20TM delivers a compact geometry that reduces material waste while maintaining stiffness under load. The slender 2.45 mm blade width produces a narrow kerf, which lowers scrap and can shorten cycle times in batch turning. At the same time, the 150 mm overall length and 32 mm blade height give sufficient engagement length for stable clamping in common parting holders, helping to avoid chatter and minimise rework. The physical dimensions are designed to balance accessibility with rigidity, so that the cutting edge remains predictable across repeated operations. Robust fitment and secure insert handling Compatibility with DGN 3 indexable inserts simplifies tool management and replacement. The blade accepts standard DGN 3 inserts, enabling rapid seating and consistent repeatability when combined with a matching parting holder. The tool’s measured cutting height of 25 mm aligns with typical holder geometries, which supports a secure clamping position and reliable chip evacuation. Clear mechanical interfaces reduce the need for frequent adjustment, translating into less downtime and a steadier production flow for workshop and industrial turning tasks. Designed for workshop efficiency and repeatability This parting blade emphasises practical benefits: a reduced kerf for material savings, dimensions that fit common holders, and compatibility with widely available inserts to ease stocking and logistics. The KL20TM’s simple specification makes it straightforward to integrate into existing tooling setups without extensive requalification. For operations where repeatable part separation and clean face finish are priorities, the blade’s proportions and insert interface contribute directly to predictable cycle outcomes and less post-process work. For precise parting results with Teknik Cutting Tools' KL20TM parting blade, contact Metav Werkzeuge in Emmerich for tailored application advice and dependable supply: info@metav-werkzeuge.com · +49 2822 7131930 Technical data Article number: KL20TM Name: Parting blade (Stechschwerter) Manufacturer: Teknik Makina eClass: 21181018 Facts Overall length: 150 mm Blade width: 2.45 mm Blade height: 32 mm Cutting height: 25 mm Maximum parting depth: 36 mm Special features Compatible with DGN 3 indexable inserts Suited for parting-off and narrow-kerf grooving Simple integration into standard parting holders FAQ What insert type fits this blade? The KL20TM parting blade is compatible with DGN 3 indexable inserts, enabling standardised insert replacement and predictable seating. Which machines is this blade intended for? This parting blade is intended for lathe parting-off and narrow-kerf grooving operations where a slim blade and reliable insert clamping are required. How does the blade geometry affect material waste? The 2.45 mm blade width produces a narrow kerf, which reduces scrap per cut and can improve material utilisation across series production. Is the KL20TM suitable for existing parting holders? The blade’s cutting height of 25 mm and overall dimensions are specified to match common parting-holder geometries, supporting secure clamping and repeatable positioning. What are the benefits of DGN 3 compatibility? Using DGN 3 inserts simplifies inventory, speeds up insert changes and helps maintain consistent cutting geometry, which supports stable process parameters and easier quality control. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a compact 12 mm shank and a precise 15.5 mm tool diameter for reliable parting results; the 150 mm overall length ensures stable reach while the secure Torx fastening speeds maintenance—order directly via Metav Werkzeuge or consult our specialists for application advice. Stechklemmhalter K832TM — Parting tool clamp holder, 15.5 mm, L150 mm (Teknik Makina) Stechklemmhalter is a compact parting and grooving clamp holder designed for precise, low‑vibration lathe operations where narrow grooves and short parting depths are required. Compact 12 mm shank for space-saving setups 15.5 mm tool diameter for narrow parting grooves 150 mm overall length for stable reach Secure Torx fastening with T7 and M2.2x6 screw Precision parting for consistent production The K832TM is engineered for reproducible parting operations where dimensional repeatability matters. The 15.5 mm diameter and 8.6 mm cutting‑head width provide a defined contact area for the cutting blade, while the 25 mm cutting height supports correct blade alignment in the tool post. With a 2 mm maximum parting depth the holder is optimised for fine separation and narrow groove tasks, reducing the need for multiple corrective passes and improving throughput. Compact form factor for machine compatibility A short, robust profile keeps the tooling package compact without sacrificing stiffness. The 12 mm shank conforms with small‑format tool posts and the S12M designation indicates compatibility with common insert and shaft systems used in light‑duty turning centres. The 150 mm overall length combined with a low mass of 0.128 kg helps to reduce cantilever‑induced vibration, enabling cleaner cuts on smaller machines and improving surface finish stability. Secure clamping and efficient maintenance Clamping is achieved via a Torx‑head screw, using a T7 key and an M2.2x6 Torx screw for repeatable, high‑torque fixation of the parting blade. The simple fastening arrangement allows quick blade changes and straightforward periodic checks, which keeps downtime to a minimum. The K832TM (SKU K832TM) is supplied with standard fastening hardware suitable for routine workshop maintenance; further technical clarifications are available from Metav Werkzeuge. Choose the Teknik Makina K832TM when compact, accurate parting is required — contact Metav Werkzeuge for procurement or technical consultation at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: K832TM Label: 15.5mm Stechklemmhalter L150mm Product type: Parting tool clamp holder Facts Diameter: 15.5 mm Overall length: 150 mm Shank diameter: 12 mm Cutting‑head width: 8.6 mm Cutting height: 25 mm Max parting depth: 2 mm Weight: 0.128 kg eClass: 21181005 Special features Bohrstange designation: S12M Torx key: T7 Torx screw: M2.2x6 SKU: K832TM FAQ What maximum parting depth is possible with this holder? The maximum parting depth for the Stechklemmhalter K832TM is 2 mm, designed for narrow separation and precision groove operations. Which shank sizes and tool posts is this clamping holder compatible with? The holder features a 12 mm shank and the S12M designation, making it compatible with standard 12 mm tool posts and light‑duty lathe turrets. How is the cutting blade secured in the clamp? Blade fixation is via a Torx screw (SKU K832TM) using a T7 key and an M2.2x6 screw for secure, repeatable clamping. Is this holder suitable for small lathes and reduced overhang setups? Yes; the compact 150 mm overall length and low mass support reduced overhang, improving stiffness and surface finish on smaller machines. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a compact 15.5 mm cutting diameter, a 150 mm overall length and secure Torx clamping for precise, repeatable parting operations; order the tool via Metav Werkzeuge or consult our specialists for integration advice. 15.5mm Parting Tool Holder S12M, L150mm (Teknik Makina) The 15.5mm parting tool holder is a dedicated clamping solution for precision parting and grooving on turning centres and compact lathes, combining a standard S12M shank with a narrow head for restricted access operations. 15.5 mm cutting diameter 150 mm overall length for reach S12M shank, 12 mm shaft diameter Torx M2.2x6 clamping screw, T7 key Stable clamping for consistent parting quality A solid mechanical connection is essential for reliable parting cycles. This clamping holder features a S12M shank and a 12 mm shaft diameter that give a rigid interface with common toolposts, while the Torx M2.2x6 screw and matching T7 key ensure secure clamping of the parting blade. The combination of a narrow head profile and firm fixation reduces vibration and walk, which results in improved surface finish and fewer rejected parts. The low mass of 0.13 kg also contributes to quick tool indexing and minimal dynamic imbalance during high-speed turning. Geometry designed to improve access and process stability Engineered with a clamp-head width of 8.6 mm and a cutting height of 20 mm, the holder permits efficient placement of parting blades close to the workpiece centre while maintaining blade support. The specified maximum plunge depth of 2 mm indicates suitability for light to medium parting tasks and fine-grooving where tight tolerances are required. Such geometry enables shorter cycle times through reduced tool interference and better chip flow, which directly supports more predictable machining and lower rework rates in batch production. Simple integration and low-maintenance operation Installation and routine handling are straightforward thanks to the standardised S12M interface and the Torx clamping system. The compact design with 150 mm overall length offers sufficient reach for most common turning setups without excess overhang, helping to preserve tool life and reduce set-up iterations. Routine checks are confined to the clamping screw and blade seating; parts can be serviced with the supplied T7 key and a standard replacement M2.2x6 screw, keeping downtime to a minimum and maintaining consistent process capability on the shop floor. Practical workshop benefits and application scope Primarily intended for precise parting and grooving operations, the holder is suitable for short, accurate cuts where blade stability and repeatability are priorities. Its modest mass and compact profile make it a practical choice for both one-off precision work and small-batch production. Where space around the spindle is limited, the narrow head and standardised shank allow quick retrofitting to existing toolposts, offering a cost-effective means to upgrade capability without major machine changes. Metav’s quality control at Emmerich ensures that each item meets the expected manufacturing tolerances and fitment standards. For precise and dependable parting operations choose Teknik Makina holders—contact Metav Werkzeuge in Emmerich for tailored advice and ordering via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: K836TM Manufacturer: Teknik Makina Product type: Parting tool holder ISO shank designation: S12M Facts Cutting diameter: 15.5 mm Overall length: 150 mm Shaft diameter: 12 mm Cutting height: 20 mm Clamp head width: 8.6 mm Max plunge depth: 2 mm Weight: 0.13 kg Torx screw: M2.2x6 Torx key: T7 Special features Shank type S12M Torx clamping screw M2.2x6 Narrow clamp head for restricted access Low mass for quick indexing FAQ What shank type does the holder use? The holder is supplied with an S12M shank, which is compatible with standard S12M toolpost systems and allows straightforward mounting in most turning toolholders. What is the maximum parting depth? The maximum plunge depth specified for this clamping holder is 2 mm, making it suitable for shallow to moderate parting cuts and fine-grooving tasks. Which clamping screw and key are required? Clamping is secured with an M2.2x6 Torx screw; a T7 key is used for tightening and loosening. What blade width can be accommodated? The clamp head width is 8.6 mm, so blades up to that width can be clamped securely in the holder. Is the tool holder suitable for high-speed turning? With a rigid S12M shank and compact construction, the holder supports stable operation; suitability for specific spindle speeds depends on blade choice and machine dynamics. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from a compact solution that combines robust clamping, precise parting geometry and rapid set-up. With a 150 mm overall length and a 2 mm cutting width, the holder delivers controlled parting performance for short- to medium-length operations — order the item directly via Metav Werkzeuge or consult our specialists for integration advice. Parting tool clamping holder L150 mm — left-hand, ISO 2525 Parting tool clamping holder L150 mm designed for left-hand parting and grooving tasks on standard turning centres and workshop lathes, offering a compact footprint and reliable clamping for repeatable operations. Left-hand cutting direction 150 mm overall length 2 mm cutting width Max parting depth 18 mm High-precision parting for consistent production results The holder is engineered as a dedicated parting tool holder, providing a rigid mounting that supports consistent cutting depth and repeatability. With an overall length of 150 mm and a compact head width of 25 mm, the design reduces deflection during plunge cuts and helps maintain finish quality. The ISO 2525 designation ensures compatibility with common toolpost systems, so the unit integrates without complex adapters. Emphasis on measurable stability translates into fewer rejected parts and lower rework costs. Rapid, secure set-up and straightforward maintenance Installation and adjustment are simplified by the supplied fastening hardware: a hex screw M6x20 and an Allen key 5 for clamping torque control. The clamping bar accepts cutting widths up to 2 mm and allows a maximum parting depth of 18 mm, enabling quick changeovers between jobs. At just 0.728 kg, the holder combines sufficient mass for dampening vibrations with a light enough weight to make handling and fixturing straightforward for operators, reducing set-up time and increasing machine utilisation. Practical fit for workshop workflows Designed for left-hand operations, the toolholder suits routine parting and grooving tasks where secure clamping and predictable chip control are priorities. The compact 25 x 25 mm cross-section of the holder body supports tight toolpost arrangements and close-quarters machining. Where space and repeatability matter, this solution helps streamline processing sequences and simplifies inventory: a single, robust holder for common parting duties supports steady throughput while minimising the number of different fixtures required at the workbench. Contact Metav Werkzeuge for tailored integration support and specify the Teknik Makina D883TM parting tool clamping holder L150 mm when ordering — our Emmerich team will advise on delivery and optimisation for specific turning applications. Technical data Article number: D883TM Label: Stechklemmhalter L150mm Product type: Stechklemmhalter Brand: Teknik Makina ISO designation: 2525 Core measurements Overall length: 150 mm Weight: 0.728 kg Holder width: 25 mm Holder height: 25 mm Cutting head width: 25 mm Max parting depth: 18 mm Cutting width: 2 mm Special features Cutting direction: left Allen key: 5 Hex screw: M6x20 SKU: D883TM eClass: 21181005 FAQ What is the maximum parting depth with this holder? The Teknik Makina D883TM parting tool clamping holder permits a maximum parting depth of 18 mm, allowing controlled plunge cuts in typical turning operations. Which fastening hardware is supplied with the holder? The holder is supplied with an M6x20 hex screw and an Allen key size 5 for secure clamping and quick installation. What are the main dimensions and weight of the unit? The holder has an overall length of 150 mm, a 25 mm × 25 mm cross-section and a weight of 0.728 kg for stable mounting and easy handling. Is the cutting direction fixed or reversible? This unit is specified for left-hand cutting; the design and clamping geometry are optimised for left-hand parting operations. How does the ISO designation affect compatibility? The ISO 2525 designation indicates standardised shank and mounting dimensions, supporting straightforward integration with compatible toolposts and holders. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact holder that combines 25×25 mm shank rigidity with a 3 mm cutting width for precise parting and grooving; the right-hand design and 150 mm overall length support stable setup and repeatable cuts—order the parting tool holder directly via Metav Werkzeuge or consult our specialists for application advice. Stechklemmhalter D721TM — Parting tool holder, 3 mm cutting width, 25×25 mm shank (Teknik Makina) A Stechklemmhalter D721TM crafted for right-hand parting and grooving tasks, optimised for Taegutec 3C TD indexable inserts and designed to fit 25×25 mm tool posts. 25×25 mm shank for stable clamping 3 mm cutting width for narrow grooves Max cutting depth 18 mm for deep parting Compatible with Taegutec 3C TD inserts Greater productivity through stable clamping and defined cutting geometry The holder’s 25×25 mm shank and compact 150 mm overall length deliver a stiff mounting that reduces vibration and improves chip control during parting and grooving cycles. With a 3 mm cutting width the tool supports narrow kerfs which conserve material and lower cutting forces, enabling higher feed rates on many turning centres. The right-hand cutting orientation provides predictable chip flow and is compatible with standard lathe spindle arrangements. These attributes combine to reduce scrap and increase throughput, making the unit a practical choice for serial work and mixed-batch production. Fast setup and standardised insert compatibility for smoother workflows Built to accept Taegutec 3C TD inserts and referenced by ISO designation 2525, the clamping system allows quick insert changes and straightforward tool re‑qualification. The holder’s interface aligns with common tool posts described as 3C-R TD, so replacement tooling is readily available and procurement is simplified. This standardisation shortens downtime during tool changes and helps maintain consistent cutting parameters across shifts, supporting leaner processes and predictable cycle times. Robust application range and benefits for workshop use Designed for parting and grooving applications, the tool accommodates a maximum cutting depth of 18 mm, which covers typical deep grooving requirements on medium‑sized workpieces. At a weight of 0.735 kg the construction balances mass for damping with manageable handling during setup. The clamping concept secures inserts against side and axial forces, which supports repeatable positioning and extends insert life when combined with correct cutting data. The result is reliable performance across steel and alloy turning operations where precise kerf width and edge control are required. For specification support or to order the Teknik Makina D721TM through Metav Werkzeuge — benefiting from our quality filter in Emmerich and specialist application advice — contact Metav Werkzeuge by eMail at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Technical Data Article number: D721TM Manufacturer: Teknik Makina Facts Shank width: 25 mm Shank height: 25 mm Cutting width: 3 mm Max cutting depth: 18 mm Overall length: 150 mm Weight: 0.735 kg Special features Compatible inserts: Taegutec 3C TD Toolholder ISO designation: 2525 Toolpost reference: 3C-R TD Cutting direction: right FAQ Which inserts fit this holder? The D721TM is compatible with Taegutec 3C TD indexable inserts; the holder accepts the standard insert form used for narrow parting and grooving tasks. What does the ISO designation 2525 indicate? The ISO designation 2525 refers to the holder’s 25×25 mm shank geometry and fitting standard, simplifying selection for toolposts and fixtures. Is the holder suitable for deep grooving? With a maximum cutting depth of 18 mm, the holder supports moderately deep grooving and parting operations typical for medium workpieces. Can the D721TM be used on CNC lathes and manual machines? Yes, the design is suitable for CNC turning centres as well as manually operated lathes that accept 25×25 mm tool posts and right-hand cutting holders. How does the 3 mm cutting width affect machining? A 3 mm kerf reduces material removal per pass, lowers cutting forces and often improves surface finish, making it preferable for narrow grooves and precise parting. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, stable holder that combines a 150 mm overall length with a 25 mm cross-section and compatibility with MGM 250 indexable inserts for reliable grooving and parting operations; order the holder directly via Metav Werkzeuge or consult their technical advisors for application support. Grooving clamp holder (Stechklemmhalter) for MGM 250 indexable inserts — L150 mm, right-hand (Teknik Makina) A robust Grooving clamp holder (Stechklemmhalter) engineered for turning and grooving applications, providing secure clamping of MGM 250 indexable inserts for consistent right-hand cutting in workshop and production environments. L150 mm shank for compact setups Compatible with MGM 250 indexable inserts Right-hand cutting orientation Supplied with M6x20 clamping screw Consistent groove quality through precise clamping The grooving clamp holder delivers stable engagement by combining a substantial cross-section of 25 mm with a purpose‑designed clamping interface for MGM 250 inserts. This geometry reduces vibration and runout during parting and grooving, which translates into improved surface finish and longer insert life. The secure retention system and the M6x20 clamping screw ensure repeatable positioning of the insert head, enabling process reliability in both single‑part and batch production. Easy integration into existing toolposts and setups Designed with common workshop standards in mind, the holder fits established toolholders and mounts without special adapters, identified by the ISO 2525 designation for straightforward specification. The compact 150 mm overall length suits confined toolstations where space is limited while still providing sufficient overhang for typical grooving depths. The right‑hand orientation supports conventional lathe setups, simplifying tool changeover and setup times at the machine. Built for controlled cutting depths and narrow grooves With a maximum grooving depth of 17 mm and a cutting width of 2.5 mm, the toolholder is optimised for narrow slotting, precision parting and finishing cuts where dimensional control is critical. The defined cutting parameters help maintain chip control and minimise deflection, leading to predictable tool performance. The holder’s cutting head width of 25 mm provides lateral stiffness that benefits repeatable depth control during continuous operations. Compatibility and traceable supply chain The holder has been specified for use with Korloy inserts of the MGM 250 family and carries the label D656TM for clear identification in tool lists and maintenance records. Manufactured by Teknik Makina, the component aligns with industry practice for indexable grooving systems and supports toolroom standardisation efforts. Traceability and clear SKU marking reduce procurement errors and aid inventory management in professional workshops. For tailored advice on integrating the Teknik Makina grooving clamp holder D656TM into production, contact Metav Werkzeuge for a direct supply from Emmerich and technical consultation: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: D656TM Manufacturer: Teknik Makina Product type: Grooving clamp holder (Stechklemmhalter) Compatible inserts: MGM 250 (Korloy) ISO designation: 2525 Facts Overall length: 150 mm Holder width: 25 mm Holder height: 25 mm Cutting head width: 25 mm Max grooving depth: 17 mm Cutting width: 2.5 mm Clamping screw: M6x20 Allen key: 5 mm Cutting direction: right-hand Special features Compatible with MGM 250 indexable inserts Label: Stechklemmhalter MGM 250 L150mm SKU: D656TM Manufacturer: Teknik Makina Purpose: Grooving and parting applications FAQ What insert type is compatible with this holder? The holder is specified for MGM 250 indexable inserts and is compatible with Korloy inserts in that family. What is the maximum grooving depth achievable? A maximum grooving depth of 17 mm is supported by the holder’s cutting head design. Which clamping hardware is supplied with the tool? The holder is supplied with an M6x20 clamping screw and requires a 5 mm Allen key for assembly. Is the holder suitable for right- and left-hand cutting? This model is manufactured for right-hand cutting orientation; select the corresponding version for left‑hand requirements. How is the holder identified for reordering? Reorder using SKU D656TM and the label for quick identification in procurement and inventory systems. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise, vibration‑resistant clamping combined with broad insert compatibility for consistent parting performance; the compact 150 mm length and M6×20 clamping screw ensure straightforward integration into existing tooling. Order the holder directly via Metav Werkzeuge or consult our specialists for application advice. Parting clamp holder MGM 300 L150mm — right-hand, for MGM 300 indexable inserts (Teknik Makina) The Parting clamp holder MGM 300 L150mm is a right-hand tool holder engineered for secure clamping of MGM 300 indexable inserts and reliable parting and grooving operations in CNC turning centres For MGM 300 indexable inserts Right-hand cutting orientation Total length 150 mm for compact set-up M6×20 clamping screw with 5 mm Allen key Stability and repeatable accuracy for parting This holder is built to deliver precision where tight tolerances matter. By pairing a rigid 25 × 25 mm shank with a reinforced head, the design reduces deflection during engagement, which lowers the risk of chatter and ensures repeatable parting profiles. Compatibility with MGM 300 inserts provides a predictable cutting geometry, so set-up times are shorter and tool offsets remain stable. The right-hand cutting orientation supports conventional lathe arrangements and simplifies programming on both manual and automated turning centres. Robust clamping system for secure insert retention A straightforward clamping arrangement combines an M6×20 clamping screw with a supplied 5 mm Allen key, enabling secure and quick tightening. The 42.5 mm head width gives a solid bearing surface for the insert seat, improving contact stability and extending insert life under typical machining loads. Because the fastening is direct and accessible, maintenance and insert changes are fast, reducing machine downtime and supporting higher shop throughput without complex tooling procedures. Application scope and measurable cutting data Designed for common industrial parting jobs, the holder accommodates a maximum cutting diameter of 350 mm and supports a cutting height of 0.965 mm, with a maximum plunge depth of 17 mm and a cutting width of 3 mm. These measurable parameters allow straightforward process planning: select the insert grade and feed to match material and finish requirements, then verify performance using the numeric values provided. Compatibility with Korloy inserts offers additional flexibility when selecting grade or geometry for steel, alloyed materials or specific surface finish targets. Easy integration into workshop tooling systems Marked with the ISO designation 2525, the tool holder fits standard turret and slot arrangements where this format is used, easing migration into existing fixtures and tool assemblies. The compact 150 mm overall length balances accessibility and rigidity, making the holder suitable for confined setups and multi‑tool turrets. Installation requires no special adapters; the clear dimensional data supports quick verification against machine and turret specifications. For mixed production environments, this holder serves as a dependable element in a modular tooling strategy. For expert selection and supply of the Teknik Makina parting clamp holder, contact Metav Werkzeuge to discuss suitability for specific machining tasks or to place an order via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data SKU: D826TM Manufacturer: Teknik Makina Product type: Parting clamp holder Compatibility: for MGM 300 indexable inserts Compatible insert manufacturer: Korloy ISO designation: 2525 Specifications Overall length: 150 mm Shank width: 25 mm Shank height: 25 mm Head width: 42.5 mm Max. cutting diameter: 350 mm Cutting height: 0.965 mm Max. plunge depth: 17 mm Cutting width: 3 mm Cutting direction: right Clamping screw: M6×20 Allen key: 5 mm Special features Label: Stechklemmhalter MGM 300 L150mm ECLASS: 21181005 For MGM 300 indexable inserts Compatible with Korloy insert system FAQ Which inserts fit this holder? The holder accepts MGM 300 indexable inserts and is compatible with Korloy insert variants; confirm the insert geometry matches the MGM 300 seat for correct clamping. What is the overall length and how does it affect stability? Overall length is 150 mm; the compact length improves rigidity compared with longer holders, helping to reduce deflection during parting and groove operations. Is the clamping hardware included, and what size is required? Clamping uses an M6×20 screw and a 5 mm Allen key is referenced for tightening; this enables straightforward insert changes and secure retention. Can this holder be used for heavy‑duty parting on large diameters? The holder supports a maximum cutting diameter of 350 mm and a maximum plunge depth of 17 mm; for heavy continuous cuts, choose inserts and machine settings that match these limits. What standard does the holder follow for mounting? The tool bears the ISO 2525 designation, facilitating integration into turrets and fixtures designed for this standard Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, production-ready holder that combines precise clamping, a narrow 3 mm cutting width, and a robust 150 mm overall length for dependable grooving and parting operations — order via Metav Werkzeuge or consult our specialists for integration advice. Grooving clamp holder for MGM 300 indexable inserts, L150mm (Teknik Makina) The grooving clamp holder for MGM 300 indexable inserts is a right-hand toolholder engineered for precise grooving and parting tasks on turning centres, compatible with Korloy MGM 300 inserts. Compatible with MGM 300 indexable inserts 150 mm overall length for deep grooving 3 mm cutting width for narrow slots Right-hand cutting orientation Consistent, measurable grooving performance for production use Designed for repeatable accuracy in series turning, this grooving clamp holder delivers a focused cutting profile thanks to its 3 mm cutting width and a 1.125 mm cutting height, which together enable narrow slotting with minimal material waste. The toolholder’s 150 mm overall length provides reach into deeper bores and long overhangs while the 42.5 mm head width ensures an optimised support surface for the insert seat. By choosing a holder tailored to the MGM 300 family, the machining process gains stability and predictable chip formation, which translates into shorter cycle times and improved workpiece consistency. Fast set-up, secure clamp and low maintenance overhead Clamping is accomplished with a standard M6x20 screw tightened using a 5 mm Allen key, allowing quick insert changes and secure fixation that resists vibration in moderate-duty turning. The 25 mm clamping height and width combine to give a rigid interface with the toolpost, reducing the need for frequent retightening. Fewer adjustments and a straightforward maintenance routine lower downtime and help maintain production cadence. Practical mechanical details such as the accessible clamping screw and standard Allen key reduce the complexity of routine servicing and spare-part logistics. Ready for shop-floor integration and compatible insert systems The holder is matched to MGM 300 indexable inserts and is suitable for inserts from Korloy, enabling straightforward replacement and common tooling strategies across the workshop. With a labelled maximum cutting diameter of 500 mm and a 17 mm maximum plunge depth, the unit fits a wide range of turning operations from fine grooving to light parting. The right-hand cutting orientation suits standard lathe setups and keeps toolpath planning simple. For manufactory teams seeking robust, interoperable tooling, this holder offers a compact, reliable option that slots into existing insert inventories and tooling programmes. For reliable grooving with Teknik Makina tooling standards, contact Metav Werkzeuge for ordering and practical advice: info@metav-werkzeuge.com or call +49 2822 7131930 — Metav’s specialists assist with specification and shop-floor integration. Technical data SKU: D827TM Label: Stechklemmhalter MGM 300 L150mm Manufacturer: Teknik Makina Core specifications Overall length: 150 mm Clamping width: 25 mm Clamping height: 25 mm Head width: 42.5 mm Maximum cutting diameter: 500 mm Cutting width: 3 mm Cutting height: 1.125 mm Maximum plunge depth: 17 mm Clamping screw: M6x20 Allen key: 5 mm Cutting direction: right ISO designation: 2525 Materials & special features Compatible with MGM 300 indexable inserts Compatible with Korloy inserts Right-hand cutting orientation Designed for grooving and parting applications FAQ Which inserts fit this holder? The grooving clamp holder is designed for MGM 300 indexable inserts and is compatible with Korloy-manufactured inserts in that series (SKU D827TM). Is the holder suitable for deep groove operations? Yes, the holder’s 150 mm overall length and 17 mm maximum plunge depth support deeper grooving tasks within the stated limits. What tools are required for insert changes? Insert retention uses an M6x20 screw accessible with a 5 mm Allen key, enabling quick and standardised insert changes. Can this holder be used for left-hand turning? This model is specified for right-hand cutting orientation; select a dedicated left-hand version if the turning setup requires left-hand cutting. What is the support width at the cutting head? The cutting-head support measures 42.5 mm which provides a stable seat for the indexable insert to resist chatter. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, robust clamp design and precise compatibility with MGM 300 indexable inserts for stable parting operations; combine the 150 mm overall length and 25 mm cross-section for repeatable set-ups and reliable chip clearance — order the holder directly via Metav Werkzeuge or request advice from our consultants. Parting clamp holder MGM 300 L150mm — left-hand parting tool, 150 mm, Teknik Makina The Parting clamp holder MGM 300 L150mm is a left-hand parting and grooving holder designed for MGM 300 indexable inserts, suitable for CNC turning applications where secure clamping and repeatable tool position are essential Left-hand cutting direction for parting tasks Compatible with MGM 300 indexable inserts 25 mm width and height for stable clamping M6x20 clamping screw and 5 mm Allen key Built for precise parting and grooving The parting clamp holder is engineered to accept MGM 300 indexable inserts and to deliver consistent engagement in turning operations. With an overall length of 150 mm and a compact cross-section of 25 mm, the holder provides a rigid mounting that reduces vibration and improves surface finish. The supplied M6x20 clamping screw and corresponding 5 mm Allen key enable straightforward insert changes and consistent clamp preload, which is critical for repeatable machining cycles on lathes and turning centres. Secure clamping for repeatable production Designed with a cutting width of 3 mm and a maximum parting depth of 26 mm, this holder supports controlled material separation while maintaining insert stability throughout the cut. The left-hand configuration suits operations that require the tool to cut from right to left, and the rated maximum turning diameter of 600 mm gives a practical envelope for medium-sized workpieces. The holder’s mass of 0.735 kg contributes to damping, helping to extend insert life and reduce unwanted chatter in high-repetition production. Simple integration and service-friendly handling Assembly and routine maintenance are straightforward thanks to the clear clamping arrangement and the ISO designation 2525, which simplifies fixture planning and inventory management. Compatibility with Korloy manufactured inserts allows flexible sourcing of cutting edges, while the compact cutting head width of 25 mm supports tight set-ups in automated tool turrets and single-tool toolposts. Ideal for workshops, job shops and OEM maintenance departments that demand dependable, easy-to-replace tooling components. For procurement assistance or to secure the Teknik Makina left-hand parting clamp holder via Metav Werkzeuge — including advice on fitment for existing toolholders and inserts — contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for specialist guidance. Technical Data Article number: D805-1TM Label: Stechklemmhalter MGM 300 L150mm Brand: Teknik Makina Product type: Stechklemmhalter ECLASS: 21181005 Facts Overall length: 150 mm Weight: 0.735 kg Tool width: 25 mm Tool height: 25 mm Cutting head width: 25 mm Max cutting diameter: 600 mm Max parting depth: 26 mm Cutting width: 3 mm Insert height: 40 mm Clamping screw: M6x20 Special features Compatible inserts: MGM 300 Compatible insert manufacturer: Korloy Cutting direction: left Hex key: 5 mm Allen Clamping holder designation ISO: 2525 FAQ Which indexable inserts fit this holder? The parting clamp holder accepts MGM 300 indexable inserts; compatibility with Korloy-made MGM 300 grades is explicitly indicated. Is the holder left-hand or right-hand? This version is configured for left-hand cutting direction, suitable for parting operations that require right-to-left engagement. What is the maximum parting depth with this holder? The holder supports a maximum parting depth of 26 mm, allowing robust grooving and parting tasks within that depth range. What clamping hardware is provided for insert fixation? The holder uses an M6x20 clamping screw and is supplied with a 5 mm Allen key for straightforward insert changes and secure clamping. Can this holder be used on workpieces up to 600 mm diameter? Yes — the technical specification lists a maximum turning diameter of 600 mm, which defines the practical envelope for safe operation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com