Gibt es einen Hahn und Kolb Online Shop?

Take advantage of sturdy clamping, precise insert compatibility and a compact 150 mm overall length for consistent grooving and parting operations; order the tool via Metav Werkzeuge or request expert advice for application-specific recommendations. Parting clamp holder for MGM 300 indexable inserts by Teknik Makina Parting clamp holder designed for precision grooving and parting with MGM 300 indexable inserts, suitable for right-hand turning applications on machine lathes Compatible with MGM 300 inserts 150 mm overall length 3 mm cutting width, 17 mm depth Right-hand cutting direction Improved rigidity and predictable cutting performance The holder’s 150 mm overall length combined with a compact 25 x 25 mm shank provides a stiff mounting that reduces chatter and improves surface finish during grooving and parting tasks. Designed for a focused contact zone, the 42.5 mm cutting-head width stabilises the insert seat so that cutting forces are transferred cleanly into the tool post. For shops seeking repeatable results, this configuration lowers scrap rates and shortens setup time by delivering a consistent tool position and minimal deflection during engagement. Fast, secure insert clamping for uninterrupted production Built for use with MGM 300 indexable inserts and tested with Korloy variants, the clamp system uses an M6x20 clamping screw with a 5 Allen hex key for rapid insert changes and secure fixation. The insert pocket complies with ISO 2525 designation, ensuring accurate seating and repeatable cutting height of 0.773 mm. This precise interface reduces the need for micro-adjustments between insert changes, supporting higher uptime and straightforward tool management in batch or series production. Practical integration into standard lathe tool setups Engineered for right-hand cutting direction and a maximum recommended cutting diameter of 36 mm, the holder suits common parting and grooving cycles where tight tolerances are required. The maximum grooving depth of 17 mm and cutting width of 3 mm make it well suited to narrow slotting operations and controlled part separation. The robust construction and straightforward geometry simplify indexing, inspection and replacement routines, helping maintain predictable cycle times and integrating easily with existing toolholders and tailstock arrangements. For a tailored recommendation or to order the Teknik Makina parting clamp holder D820TM, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 for immediate advisory support Technical data SKU: D820TM Manufacturer: Teknik Makina Product type: Stechklemmhalter Label: Stechklemmhalter MGM 300 L150mm eClass: 21181005 Facts Overall length: 150 mm Shank width: 25 mm Shank height: 25 mm Cutting-head width: 42.5 mm Max cutting diameter: 36 mm Cutting height: 0.773 mm Max grooving depth: 17 mm Cutting width: 3 mm Cutting direction: right Clamping screw: M6x20 Hex key: 5 Allen Special features Compatible with MGM 300 indexable inserts Recommended insert manufacturer: Korloy Clamping designation: ISO 2525 Clamp type: parting/grooving holder SKU reference: D820TM Brand: Teknik Makina FAQ What insert type does this holder accept? The parting clamp holder accepts MGM 300 indexable inserts; the pocket and clamping arrangement are tailored to that family for secure seating. Can the holder be used for left‑hand cutting? This holder is configured for right‑hand cutting direction; left‑hand use is not supported by the defined geometry. What is the maximum grooving depth and width achievable? Maximum grooving depth is 17 mm with a cutting width of 3 mm, suitable for narrow slotting and parting tasks. Which clamping hardware is supplied for insert fastening? The tool uses an M6x20 clamping screw tightened with a 5 Allen hex key for reliable insert fixation. Is the holder compatible with Korloy inserts? Yes, the holder is compatible with Korloy variants of the MGM 300 family and has been specified for those insert dimensions where noted. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust clamping design and precise compatibility with MGM 300 indexable inserts for consistent parting performance; the 150 mm overall length and right-hand cutting orientation ensure stable set-up and predictable chip control. Order directly via Metav Werkzeuge or contact our consultants for advice and availability. Parting clamp holder MGM 300 L150mm — 150 mm right-hand parting holder by Teknik Makina The Parting clamp holder MGM 300 L150mm is a right-hand parting tool holder engineered for grooving and parting operations with MGM 300 indexable inserts on lathes and turning centres. *Compatible with MGM 300 indexable inserts *Length 150 mm for stable tooling *Right-hand cutting direction *Holds Korloy inserts securely with M6x20 clamp screw Stable parting performance through measured design The holder delivers consistent results by combining a 150 mm overall length with a compact clamping body that reduces vibration. The 25 mm block width and 25 mm block height form a rigid foundation, while the 42.5 mm cutting-head width positions the insert for controlled engagement. These measurable characteristics minimise chatter and extend insert life, resulting in improved machining efficiency and repeatable part tolerances when using MGM 300 inserts. Secure clamping and quick set-up for production environments Clamping is executed via an M6x20 clamp screw operated with a 5 mm Allen key, enabling fast insert changes without compromising stability. The ISO designation 2525 describes the holder interface and helps with fixture planning and spindle clearance checks. A 3 mm maximum cutting width and 17 mm maximum plunging depth accommodate standard parting and grooving tasks; the defined parameters aid process planning, reducing trial-and-error during set-up and increasing uptime. Application scope and workshop benefits Designed for right-hand cutting, this toolholder suits a wide range of turning applications where precise parting and grooving are required. Compatibility with Korloy inserts offers access to widely available cutting grades and geometries, allowing optimisation for materials such as steel and alloyed components. The model (SKU D824TM) supports efficient workshop workflows by simplifying tooling inventories and ensuring rapid replacement in routine maintenance cycles. Choose Teknik Makina quality for accurate, reliable parting — contact Metav Werkzeuge for personalised advice and to arrange supply of the D824TM: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: D824TM Label: Stechklemmhalter MGM 300 L150mm Manufacturer: Teknik Makina eClass: 21181005 Dimensions and key figures Overall length: 150 mm Clamp width: 25 mm Clamp height: 25 mm Cutting-head width: 42.5 mm Maximum cutting diameter: 150 mm Cutting width: 3 mm Insert height: 0.771 mm Maximum plunging depth: 17 mm ISO designation: 2525 Cutting direction: right Clamp screw: M6x20 Allen key: 5 mm Compatibility and features Compatible inserts: MGM 300 indexable inserts Suitable insert manufacturer: Korloy Right-hand parting applications SKU: D824TM FAQ What inserts fit this holder? The parting clamp holder accepts MGM 300 indexable inserts; the holder is specified for inserts from Korloy and compatible grades. Which cutting direction does the tool require? This holder is configured for right-hand cutting and is intended for right-hand parting and grooving operations. What is the maximum plunging depth with this holder? The maximum plunging depth is 17 mm, allowing controlled shoulder cuts and conventional parting depths. Which fastener is used for clamping the insert? Clamping is performed with an M6x20 screw tightened with a 5 mm Allen key for quick and secure insert changes. What is the article number or SKU for ordering? The SKU for this parting clamp holder is D824TM, listed as Stechklemmhalter MGM 300 L150mm by Teknik Makina. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a precise, compact clamping solution that combines stable clamping performance with compatibility for MGM 300 indexable inserts and a 150 mm overall length; order directly via Metav Werkzeuge or consult the team for application advice. Parting Clamp Holder MGM 300 L150mm – compact holder for right-hand parting A robust Parting Clamp Holder MGM 300 L150mm designed for right-hand parting and grooving operations, compatible with MGM 300 indexable inserts and optimised for workshop use. Compact L150 mm design for tight setups Compatible with MGM 300 indexable inserts 25 mm clamping width and 25 mm clamping height Maximum cutting diameter 48 mm, right-hand cut Engineered precision for consistent parting results The holder is engineered to deliver steady results across repetitive parting tasks: its compatibility with MGM 300 indexable inserts ensures a predictable tool life and repeatable geometry, while the specification for a 48 mm maximum cutting diameter and a cutting height of 0.772 mm supports controlled chip formation. The narrow 3 mm cutting width and ISO designation 2525 enable fine, accurate cuts with reduced lateral play, which translates into fewer rework cycles and a lower scrap rate. These measurable design choices prioritise process stability and machining predictability, important for production environments where cycle time and quality are decisive. Faster set-ups and straightforward handling for shop floors A compact overall length of 150 mm and symmetric 25 mm clamping width and height make fixture planning simpler and enable closer tool spacing. The clamping screw M6x20 and supplied 5 mm Allen key permit quick insert changes and secure fastening without the need for specialised tools. Reduced setup complexity shortens machine downtime and increases throughput: fewer adjustments are required to achieve the correct cutting geometry, and the clear mechanical interface reduces the risk of incorrect tightening. For workshops aiming to improve uptime, the holder contributes directly to operational efficiency and ease of maintenance. Durable configuration that matches common insert systems and applications Built for everyday use in turning and parting operations, the holder supports inserts from recognised suppliers such as Korloy, ensuring broad availability of cutting grades and geometries for different materials. The right-hand cutting orientation and a maximum plunge depth of 17 mm allow confident application in standard lathe setups, while the cutting head width of 42.5 mm provides a solid mounting plane to resist vibration. Backed by Teknik Makina’s production heritage, the design emphasises mechanical robustness and consistent clamp force to maintain tool position and surface finish over extended runs. For tailored advice and reliable delivery of the Teknik Makina parting clamp holder, contact Metav Werkzeuge for personalised application support and rapid shipment of SKU D821TM. Technical Data SKU: D821TM Label: Stechklemmhalter MGM 300 L150mm Manufacturer: Teknik Makina Product type: Parting clamp holder ISO designation: 2525 Core dimensions and performance Overall length: 150 mm Clamping width: 25 mm Clamping height: 25 mm Cutting head width: 42.5 mm Max. cutting diameter: 48 mm Cutting height: 0.772 mm Cutting width: 3 mm Max. plunge depth: 17 mm Clamping screw: M6x20 Allen key: 5 mm Compatibility and special features For MGM 300 indexable inserts Compatible with Korloy inserts Right-hand cutting direction ISO 2525 holder designation Label D821TM FAQ Which inserts fit this holder? The holder accepts MGM 300 indexable inserts and is confirmed compatible with inserts from Korloy; the design follows the ISO 2525 holder standard for a reliable fit. What is the maximum cutting diameter for this clamping tool? The maximum cutting diameter is 48 mm, which is suitable for a wide range of parting and grooving operations when using the correct insert geometry and setup. How deep can the holder plunge when parting? A maximum plunge depth of 17 mm is specified, enabling confident parting-in operations within that limit while maintaining clamp stability. What fastening and adjustment tools are required? Fastening is by an M6x20 clamping screw; adjustments and insert changes use a 5 mm Allen key as specified in the technical data. Is the holder right- or left-handed? This holder is configured for right-hand cutting operations and is manufactured by Teknik Makina under SKU D821TM for workshop integration. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; info@metav-werkzeuge.com

Combine a compact L150 mm design with secure clamping for MGM 300 indexable inserts and a robust M6x20 clamping screw to achieve consistent parting results; order the holder directly via Metav Werkzeuge or consult the specialists for application support. Parting tool clamping holder D823TM – for MGM 300 inserts, L150 mm (Teknik Makina) The parting tool clamping holder D823TM is a right‑hand clamping solution designed to secure MGM 300 indexable inserts for efficient parting and grooving operations in CNC turning. Compatible with MGM 300 indexable inserts Compact L150 mm overall length Right‑hand cutting direction ready Clamping with M6x20 screw and 5 mm Allen key Precision clamping for repeatable parting quality A reliable clamping interface is decisive for consistent results in parting operations. The holder’s ISO 2525‑compliant geometry and the M6x20 clamping screw deliver a secure seat for MGM 300 inserts, which reduces vibration and improves surface finish. With an insert height of 0.762 mm and a defined cutting width of 3 mm, the system supports precise material separation with minimal tool deflection. The integrated clamping arrangement allows repeatable positioning of indexable inserts, meaning fewer adjustments during production and better overall process stability. Built for quick set‑up and dependable cycle times Workshop efficiency benefits from straightforward handling and compact dimensions. The short L150 mm overall length together with a holder width and height of 25 mm keeps the tool overhang low, aiding rigidity on the turret. The cutting head spans 42.5 mm, and the assembly is configured for right‑hand cutting, matching common turning setups. Practical features such as compatibility with Korloy inserts, the supplied 5 mm Allen key and the robust M6x20 screw reduce changeover times and maintenance needs. With a maximum parting depth of 17 mm and a maximum cutting diameter of 110 mm, the holder supports a range of typical turning tasks while maintaining dependable clamping force. Improve uptime with standardised components and simple service Standardised interfaces and familiar hardware mean easier inventory management and quicker servicing intervals. The holder’s ISO designation and common fasteners make replacement and spare‑part planning straightforward, supporting lean workshop procedures. Combining the mechanical advantages of the clamping design with Metav’s distribution and product range ensures steady availability and technical guidance when specifying tooling for production lines. The result is a practical parting solution that helps optimise cycle times and simplifies tool management without compromising process reliability. For precise parting with guaranteed compatibility to MGM 300 inserts, contact Metav Werkzeuge in Emmerich for tailored specification advice and order support. Technical data SKU: D823TM Label: Stechklemmhalter MGM 300 L150mm Manufacturer: Teknik Makina Core dimensions Overall length: 150 mm Holder width: 25 mm Holder height: 25 mm Cutting head width: 42.5 mm Maximum cutting diameter: 110 mm Maximum parting depth: 17 mm Cutting width: 3 mm Insert height: 0.762 mm Features Compatible with MGM 300 indexable inserts Suitable for Korloy inserts ISO designation 2525 Clamping screw M6x20 Comes with 5 mm Allen key Right‑hand cutting direction FAQ Which inserts fit this holder? The parting tool clamping holder accepts MGM 300 indexable inserts and is specified for inserts from manufacturers such as Korloy. What is the maximum parting depth? The maximum parting depth for this holder is 17 mm. Is the holder set up for right‑ or left‑hand cutting? This clamping holder is configured for right‑hand cutting direction. What fasteners and tools are required for installation? Installation uses the M6x20 clamping screw; a 5 mm Allen key is supplied for secure tightening. What are the key dimensions for turret planning? Key dimensions include overall length 150 mm, holder width 25 mm, holder height 25 mm, cutting head width 42.5 mm and maximum cutting diameter 110 mm. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise clamping, compatibility with MGM 300 indexable inserts and a compact 150 mm shank for controlled parting operations; order the holder directly via Metav Werkzeuge or ask our consultants if needed Parting clamping holder MGM 300 L150mm — right-hand parting tool holder with ISO 2525 interface Parting clamping holder MGM 300 L150mm is a right-hand parting tool holder engineered for secure clamping of MGM 300 indexable inserts in precision turning and grooving applications 150 mm shank length for deep cuts Compatible with MGM 300 indexable inserts Right-hand cutting direction 25 mm clamping width, ISO 2525 interface Engineered for repeatable, high-precision parting The holder is built to deliver consistent results in parting and grooving operations. Its ISO 2525 clamping interface and compatibility with MGM 300 indexable inserts reduce setup variation and support repeatable tool seating, which translates into fewer rejects and less rework. The 150 mm shank provides the reach required for deeper cuts while maintaining rigidity. Technical features such as the 42.5 mm toolhead width and defined cutting height ensure the insert sits at the correct centre line for accurate engagement with the workpiece. Secure clamp, simple maintenance, reliable changeover Clamping is handled via an M6x20 clamping screw and a 5 mm Allen key, offering a robust connection that resists loosening under typical cutting forces. The 25 mm clamp width and compact tool geometry minimise vibration and support stable cutting conditions. Because the design uses standardised interfaces and fasteners, insert changes and routine checks are straightforward, reducing machine downtime. Clear mechanical fixing and standard hardware mean maintenance requires only basic workshop tools and a short service interval. Practical performance for everyday workshop productivity Designed for right-hand operations, this holder supports a maximum effective cutting diameter of 70 mm and a plunge depth of 17 mm, with a cutting width of 3 mm, enabling controlled material separation in a broad range of turning tasks. Compatibility with Korloy-manufactured inserts increases flexibility within existing tooling stocks, allowing quick adaptation between parting and grooving jobs. The compact, purpose-built geometry delivers a balance of access and rigidity, making the holder suitable for small-batch production and repair work where predictable tool behaviour is essential. For reliable parting performance and fast supply from Emmerich, request a tailored quote via Metav Werkzeuge or contact our specialists at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: D822TM Product type: Stechklemmhalter (parting clamping holder) Label: Stechklemmhalter MGM 300 L150mm eClass: 21181005 For indexable inserts: MGM 300 Compatible insert manufacturer: Korloy Secondary designation (EN): for MGM 300 Indexable Inserts ISO designation: 2525 Clamping screw: M6x20 Allen key: 5 Allen Overall length: 150 Cutting direction: right Numbers / Core technical data Clamping width: 25 mm Holder height: 25 mm Cutting head width: 42.5 mm Max cutting diameter: 70 mm Cutting height: 0.767 mm Max plunge depth: 17 mm Cutting width: 3 mm Designs / Special features Right-hand cutting direction Compatible with MGM 300 indexable inserts ISO 2525 clamping interface Includes M6x20 clamping screw Requires 5 mm Allen key Label/SKU: D822TM FAQ Is the holder compatible with Korloy MGM 300 inserts? Yes. The parting clamping holder is compatible with MGM 300 indexable inserts and is listed as suitable for inserts from Korloy (SKU D822TM). What is the maximum cutting diameter supported? The holder supports a maximum effective cutting diameter of 70 mm for standard parting and grooving operations. Which cutting direction does this holder support? This design is for right-hand cutting direction and is optimised for right-hand parting applications. What clamping hardware is required for mounting and insert changes? Clamping uses an M6x20 screw and a 5 mm Allen key for fastening, providing a secure and serviceable connection. How deep can the tool plunge and what is the maximum cutting width? The tool provides a maximum plunge depth of 17 mm with a cutting width of 3 mm, suitable for controlled parting cuts Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining precise compatibility with MGM 400 indexable inserts, a compact 150 mm overall length and a robust right‑hand clamping concept, this holder delivers stable grooving and repeatable results in production environments. Order the Stechklemmhalter directly via Metav Werkzeuge or ask our consultants if needed. Stechklemmhalter MGM 400 L150mm — Right‑hand grooving clamp holder, 150 mm, Teknik Makina Stechklemmhalter MGM 400 L150mm is a purpose‑built clamping tool for grooving and parting operations, designed to accept MGM 400 indexable inserts for industrial turning applications. For MGM 400 indexable inserts 150 mm overall length Right‑hand cutting direction Max grooving depth 20 mm Stable clamping for predictable production output The holder delivers a stable clamping interface that reduces vibration and increases tool life. Fitted for MGM 400 indexable inserts and compatible with Korloy tool grades, the device is engineered to keep insert seating rigid under cutting forces. The integrated clamp uses an M6x20 Torx screw and requires a T20 Torx driver plus a 5 mm Allen key for secure assembly; this combination simplifies changeovers and shortens downtime. By maintaining consistent insert position, the system supports repeatable groove dimensions and reduces scrap rates, making it well suited to batch production and high‑mix turning centres. Precise groove control with compact geometry Thanks to a 150 mm overall length and a compact cutting head width of 45 mm, the holder grants excellent access in confined workpiece zones while still offering measurable cutting stability. The tool supports a cutting width of 4 mm and a maximum grooving depth of 20 mm, enabling controlled material removal for typical grooving and parting tasks. The specified cutting height of 0.748 mm assists in selecting the matching insert geometry so that chip formation and evacuation are consistent. For operators new to indexable tooling: “right‑hand” indicates the holder is intended for cuts produced when the tool advances from left to right relative to the lathe spindle rotation. Workshop compatibility and ergonomic maintenance Designed in accordance with an ISO 2525 holder designation, this clamping solution integrates with common toolholders and simplifies toolroom logistics. The compact design and standardised fixings make installation straightforward on compatible tool posts, reducing set‑up time and the need for specialised equipment. The holder’s compatibility with Korloy inserts broadens procurement options and allows workshops to capitalise on established insert grades without bespoke retooling. Overall, the combination of standard fastenings, clear dimensional data and established insert compatibility contributes to a more efficient tool‑management strategy and predictable machining cycles. For reliable supply, compatibility checks and swift delivery from Metav Werkzeuge in Emmerich, contact Metav Werkzeuge for tailored advice and a project quotation at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: D834TM Product type: Stechklemmhalter Manufacturer: Teknik Makina Compatible inserts: MGM 400 Compatible insert maker: Korloy ISO designation: 2525 Facts Overall length: 150 mm Holder width: 25 mm Holder height: 25 mm Cutting head width: 45 mm Max cutting diameter: 200 mm Cutting height: 0.748 mm Cutting width: 4 mm Max grooving depth: 20 mm Cutting direction: right Special features Torx screw M6x20 Torx key T20 required 5 mm Allen key required Designed for grooving and parting operations Compact geometry for confined workpiece access FAQ Which indexable inserts fit this holder? The Stechklemmhalter accepts MGM 400 indexable inserts and has been specified for compatibility with Korloy insert grades; the SKU is D834TM by Teknik Makina. Is the holder right‑hand or left‑hand? This clamping holder is configured for right‑hand cutting direction; it is intended for cuts where the tool moves from left to right relative to spindle rotation. What is the maximum grooving depth? The maximum grooving depth is 20 mm, which supports a wide range of standard grooving applications without additional modification. Which tools are needed for assembly and insert changes? Assembly requires a T20 Torx driver for the M6x20 screw and a 5 mm Allen key for auxiliary fastening; these standard tools simplify workshop maintenance. Can this holder be used with other insert manufacturers? The holder is specified for MGM 400 inserts and listed as compatible with Korloy; users may verify other brands’ geometry against MGM 400 dimensions for fitment. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust clamping, precise compatibility with MGM 400 indexable inserts and a compact 150 mm length for stable parting operations. Order the holder via Metav Werkzeuge for reliable supply and expert advice. Parting clamp holder "Stechklemmhalter MGM 400 L150mm" by Teknik Makina — 150 mm, for MGM 400 indexable inserts A parting clamp holder designed for industrial turning and grooving applications, compatible with MGM 400 indexable inserts and built for secure clamping in medium-deep parting operations. Robust parting holder for MGM 400 inserts 150 mm overall length for deeper operations 25 mm clamp width for rigid clamping Compatible with Korloy MGM 400 indexable inserts Engineered for stable parting and consistent chip control The holder is optimised to secure MGM 400 style indexable inserts with a focus on rigidity and predictable chip flow. Its 150 mm overall length provides reach for deeper parting tasks while keeping vibration low, which in turn extends insert life and reduces surface finish variability. The design translates into fewer tool changes, more predictable cycle times and less scrap, supporting efficient production rhythms in small-batch and series machining alike. Faster set-up and dependable clamping for the workshop Familiar, workshop-grade fastening makes setup straightforward. The clamping arrangement follows the ISO 2525 designation and is secured with a Torx T20 drive and M6x20 screw for repeatable torque and secure seating of the insert. An Allen key: 5 is specified for auxiliary adjustments. These standardised interfaces reduce downtime during tool changes and simplify spare-part inventories, delivering measurable time savings at the machine spindle. Dimensioned for predictable cutting performance Critical dimensions determine what can be achieved at the cutting edge: a maximum cutting diameter of 48 mm, a cutting height of 0.775 mm and a maximum parting depth of 20 mm. These figures help to select the correct insert geometry and cutting parameters and make it straightforward for process engineers to calculate feeds and speeds. Compatibility with Korloy supplied inserts broadens material and grade choices for optimising performance across a range of steels and non-ferrous materials. Durable construction that supports workshop reliability A focused design with a 25 mm clamp width and a 42.5 mm cutting-head width prioritises mechanical stability during parting operations. Routine maintenance is uncomplicated thanks to standard fasteners and clear mechanical interfaces, which helps to keep the toolroom running and inventory predictable. Where traceable supply and dependable quality matter, this holder integrates easily into an organised tooling strategy without introducing exotic or proprietary elements. For technical procurement or process consultation on the Teknik Makina parting clamp holder, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 for fast, reliable supply and expert advice. Technical data Article number: D829TM Label: Stechklemmhalter MGM 400 L150mm Manufacturer: Teknik Makina SKU: D829TM Core data Overall length: 150 mm Clamp width: 25 mm Holder height: 25 mm Cutting-head width: 42.5 mm Max cutting diameter: 48 mm Cutting height: 0.775 mm Max parting depth: 20 mm Cutting width: 4 mm Torx key: T20 Torx screw: M6x20 Allen key: 5 Special features Compatible with MGM 400 indexable inserts Suitable insert supplier: Korloy Clamping designation: ISO 2525 Product type: Parting clamp holder FAQ What inserts fit this holder? The holder accepts MGM 400 indexable inserts; it is also specified as compatible with inserts from Korloy for straightforward procurement and grade selection. What is the maximum cutting diameter for use with this holder? The maximum cutting diameter is 48 mm, which sets the practical envelope for parting and grooving operations using this holder. Which fasteners are used for the clamping mechanism? Clamping is secured with a Torx T20 drive and an M6x20 screw; an Allen key: 5 is listed for auxiliary adjustments. How deep can the tool cut in a single pass? The holder supports a maximum parting depth of 20 mm, enabling medium-depth operations without compromising stability. Is the holder suitable for high-speed turning? The mechanical design emphasises rigidity and secure insert seating; compatibility with appropriate insert grades for high-speed turning should be verified with the chosen insert supplier. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact holder that pairs precise clamping with broad compatibility: the combination of a 150 mm overall length and compatibility with MGM 400 indexable inserts delivers stable grooving and parting operations. Order the grooving clamp holder directly via Metav Werkzeuge or request advice from our consultants for seamless integration into production. Grooving clamp holder MGM 400 L150mm – 150 mm, right-hand | Teknik Makina Grooving clamp holder MGM 400 L150mm is a right-hand clamping tool engineered for precise parting and grooving using MGM 400 indexable inserts 150 mm overall length for compact setups Compatible with MGM 400 indexable inserts Right-hand cutting orientation 25 x 25 mm shank, ISO 2525 Consistent cutting performance for high-throughput production The Grooving clamp holder MGM 400 L150mm provides a stable interface between machine and insert, reducing vibration and securing predictable chip formation. Its compact 150 mm length and 25 x 25 mm shank meet standard toolpost geometries, enabling quick changeovers and repeatable set-ups. The right-hand orientation and a 45 mm cutting-head width ensure the tool aligns correctly for conventional turning centres, while the robust clamping geometry supports steady 4 mm cutting widths. This reliability translates into fewer interrupted cycles and improved process efficiency for batch and single-part production. Designed for predictable accuracy and broad material use The holder is configured to accept MGM 400 indexable inserts from established manufacturers such as Korloy, so insert procurement and replacement are straightforward. Engineered limits—20 mm maximum plunge depth and 1.126 mm cutting height—define safe operating envelopes for grooving tasks, while a maximum recommended cutting diameter of 500 mm suits many lathe sizes. Clear specification of these parameters reduces setup uncertainty and helps planners select feeds and speeds that balance tool life and cycle time, supporting a rational decision-making process for production managers. Practical fastening and service-friendly design Maintenance and retooling are minimised by familiar fastening standards: the clamping screw is M6x20 tightened with a Torx T20, while assembly and adjustments can be carried out using the 5 Allen key. The ISO shank designation 2525 simplifies fixture planning and cataloguing. These features lower downtime during insert changes and make the holder compatible with established workshop routines. For buyers seeking a dependable, low-complexity grooving solution, the unit’s straightforward mechanics and standardized fasteners are a practical advantage. For tailored guidance or to arrange delivery from Emmerich, contact Metav Werkzeuge – info@metav-werkzeuge.com or +49 2822 7131930; request the Teknik Makina grooving clamp holder MGM 400 L150mm to ensure robust, repeatable grooving and parting performance Technical data SKU: D836TM Label: Stechklemmhalter MGM 400 L150mm Manufacturer: Teknik Makina Product type: Stechklemmhalter ECLASS: 21181005 Compatible inserts: MGM 400 Compatible insert manufacturer: Korloy Facts Overall length: 150 mm Shank width x height: 25 x 25 mm Cutting-head width: 45 mm Max cutting diameter: 500 mm Cutting height: 1.126 mm Cutting width: 4 mm Max plunge depth: 20 mm Screw: M6x20 Torx key: T20 Allen key: 5 Special features Right-hand cutting orientation ISO shank designation 2525 Torx M6x20 clamping screw Compatibility with Korloy MGM 400 inserts FAQ Which inserts fit this holder? The holder is specified for MGM 400 indexable inserts; compatibility with Korloy MGM 400 grades is confirmed for straightforward procurement and replacement. What is the maximum plunge depth for grooving operations? The holder supports a maximum plunging depth of 20 mm, providing a clear limit for safe grooving and parting procedures. Which fastening tools are required for assembly and insert changes? Insert clamping uses an M6x20 screw driven with a Torx T20, while holder adjustments can be made with the supplied 5 Allen key. Is the shank size industry standard for rapid toolpost mounting? Yes; the shank follows the ISO 2525 designation at 25 x 25 mm, making it compatible with standard toolposts and fixtures. Can this holder be used on medium and large lathes? With a maximum recommended cutting diameter of 500 mm, the holder suits many medium to large lathe centres for typical parting and grooving tasks. Manufacturer/Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of precise, repeatable parting and grooving with compact dimensions and secure clamping for uninterrupted production. Benefit from the compatibility with MGM 400 indexable inserts and the straightforward fastening system to keep setup times short. Order via Metav Werkzeuge or contact the consultants for specification advice. Parting clamp holder MGM 400 L150 mm by Teknik Makina — rigid clamping for grooving and parting Parting clamp holder for MGM 400 indexable inserts designed for right-hand grooving and parting operations on production lathes Compact L150 mm design for tight tool paths Compatible with MGM 400 indexable inserts Suitable for Korloy insert series Right-hand cutting orientation Max cutting diameter 70 mm Consistent parting performance for production lathes Built for predictable results, this parting clamp holder combines a compact L150 mm body with a rigid clamping interface to reduce vibration and maintain insert position under load. The robust geometry stabilises the cutting edge and supports consistent chip control, which lowers scrap rates and reduces downstream rework. The right-hand configuration is tailored for standard lathe feed directions, so cycle times remain efficient while process stability is increased. Quick set-up and reliable fastening to speed machine changeovers The holder is engineered for fast, repeatable mounting: the clamping screw is M6x20, driven with a T20 Torx, and an accessible 5 mm Allen arrangement is provided for secondary adjustments. These familiar fasteners mean the setup sequence is simple and can be standardised across multiple stations, cutting non-productive time. Fewer tool changes and clearer torque points translate directly into higher machine availability on batch and continuous runs. Precise dimensions that support cutting accuracy and tool life Dimensional stability is a core advantage: a 25 mm holder width and 25 mm height position the insert securely, while the cutting head measures 42.5 mm across to give a stable support plane. The tool accepts a 4 mm cutting width and permits a maximum parting depth of 20 mm, with a max cutting diameter 70 mm guideline for safe operation. Maintaining the correct cutting height is essential for insert life and surface finish; the small, defined cutting height ensures the insert engages the workpiece with the intended geometry rather than relying on compensation from the machine. Broad compatibility and focused application range Designed around the MGM 400 insert form, the clamp holder is fully compatible with Korloy-manufactured inserts and comparable MGM 400 styles from other suppliers, simplifying procurement and stocking. The construct is optimised for parting and grooving tasks on CNC lathes where space is restricted and reliable clamp pressure is required. This compatibility ensures that suitable inserts are readily available and replacement cycles remain predictable. Durable design for routine workshop use and maintenance The component’s layout facilitates routine inspection and service: the fasteners are externally accessible and the clamping interface can be checked without disassembly of the entire toolpost, enabling planned maintenance without extended downtime. Supplied specifications and the compact form factor aid integration into existing tool sets, and the straightforward mechanical design supports longevity in demanding production environments. Contact Metav Werkzeuge for tailored advice on the Teknik Makina parting clamp holder D830TM and request supply from our Emmerich warehouse; consultants are available to confirm fitment and optimal insert selection Technical data Article number / SKU: D830TM Product type: Parting clamp holder Brand: Teknik Makina Compatible inserts: MGM 400 Suitable insert manufacturer: Korloy Facts Overall length: 150 mm Holder width: 25 mm Holder height: 25 mm Cutting head width: 42.5 mm Max cutting diameter: 70 mm Cutting width: 4 mm Max parting depth: 20 mm Cutting height: 0.783 mm Cutting direction: right Special features Clamping screw: M6x20 Torx key: T20 Allen key / hex: 5 mm ISO designation: 2525 SKU: D830TM FAQ Which inserts fit this clamp holder? The holder accepts MGM 400 indexable inserts; Korloy MGM 400 variants are explicitly suitable and commonly used with this holder. Is the holder suitable for left-hand operations? No, the tool is designed for a right-hand cutting direction; left-hand applications require a corresponding left-hand holder. Which fasteners and tools are required for assembly? Assembly uses an M6x20 clamping screw with a T20 Torx drive; an additional 5 mm Allen hex is referenced for related adjustments. What are the maximum cutting depth and diameter? Maximum parting depth is 20 mm and the guideline for safe operation is a max cutting diameter of 70 mm. Can this holder be used in tight toolpost spaces? Yes, the L150 mm compact design and 25 mm width are intended for confined toolpaths where secure clamping is still required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, precision clamping solution that combines compatibility with MGM 400 indexable inserts, a robust L150 mm overhang and a dedicated right-hand cutting orientation for reliable parting and grooving operations. Order the parting clamp holder directly via Metav Werkzeuge or consult our specialists for process integration and tool selection. Parting clamp holder — for MGM 400 indexable inserts, L150 mm (Teknik Makina) Parting clamp holder for right-hand external grooving and parting on lathes, designed to accept MGM 400 indexable inserts for high repeatability and stable cutting. Compatible with MGM 400 indexable inserts L150 mm overall length for secure tool projection 25 mm clamp width for rigid workholding Right-hand orientation for standard lathe set-ups Consistent parting performance with predictable results The holder is engineered for repeatable parting and grooving where dimensional control is essential. With a rigid 25 mm clamping section and L150 mm overall length, the assembly reduces flex and runout that can cause burrs or rework. Compatibility with MGM 400 indexable inserts provides a clear upgrade path to modern insert geometries; the measured 0.961 mm insert seat height aligns insert tip position consistently, which simplifies setting and minimises trial cuts. These measurable design choices contribute directly to fewer rejected parts and a more efficient cycle time on the machine. Secure clamping and straightforward fastening for minimal downtime Clamping stability is aided by a precise interface and standard fastenings that support quick tool changes. The device lists an M6x20 Torx screw for the cutting head and specifies a T20 Torx drive plus a 5 mm Allen key interface for auxiliary adjustments, enabling maintenance with common workshop tools. The 25 mm clamp width and 25 mm clamp height combine to hold inserts with low vibration transmission; the result is improved surface finish and extended insert life, which lowers running costs per component without sacrificing machining speed. Designed to withstand robust workshop conditions A wider cutting head of 45 mm and a maximum recommended cutting diameter of 350 mm make the holder suitable for a broad range of external turning and parting tasks in general engineering and light to medium-duty industrial environments. The controlled 4 mm maximum cut width and 20 mm maximum plunge depth provide clear operational limits for safe, repeatable operations on conventional and CNC lathes. Compatibility with Korloy inserts ensures access to established insert geometries and grades for different materials and cutting conditions, supporting adaptability across parts families. Practical integration into production workflows The holder carries an ISO-style tag 2525, which helps to locate matching tool posts and mounting bushes and speeds up inventory matching in toolrooms. Its right-hand orientation suits the majority of lathe setups; for non-standard arrangements, consider fixture orientation during programming. The compact design supports lean tool stations and reduces tool-change interference, enabling faster set-ups and less downtime between batches. For purchasing and technical enquiries Metav Werkzeuge can advise on process pairing and supply logistics to ensure swift delivery to the workbench. For procurement or technical advice on the Teknik Makina parting clamp holder, contact Metav Werkzeuge in Emmerich for tailored recommendations at info@metav-werkzeuge.com or call +49 2822 7131930. Technical data SKU: D835TM Product type: Parting clamp holder Model designation: for MGM 400 indexable inserts Manufacturer: Teknik Makina Overall dimensions & key numeric data Overall length: 150 mm Clamp width: 25 mm Clamp height: 25 mm Cutting-head width: 45 mm Maximum cutting diameter (Dmax): 350 mm Insert seat height: 0.961 mm Maximum plunge depth: 20 mm Cutting width: 4 mm Fastener: M6x20 Designs & special features Compatible with MGM 400 indexable inserts Compatible insert manufacturer: Korloy Right-hand cutting orientation ISO designation: 2525 Torx screw drive: T20 Allen key interface: 5 mm FAQ Which insert series fits this clamp holder? The clamp holder accepts MGM 400 indexable inserts; Korloy-manufactured inserts in that series are suitable and widely available for various grades and chipbreakers. What are the maximum cutting dimensions for safe operation? Rated figures include a maximum cutting diameter of 350 mm, a maximum plunge depth of 20 mm and a cutting width of 4 mm, providing clear operational guidelines for parting and grooving tasks. Which fasteners and drive sizes are specified for assembly? Assembly and head fastening use an M6x20 screw; the holder references a T20 Torx drive and a 5 mm Allen interface for related adjustments. Is the holder suitable for heavy interrupted cuts or only finishing passes? The holder's 25 mm clamping width and 45 mm cutting-head width provide rigidity for stable cuts, but machining strategy should follow the specified maximum plunge and width limits to avoid overload. How does the insert seat height affect set-up? The 0.961 mm seat height ensures a consistent insert tip position, simplifying height set-up at the tool post and reducing the need for shim adjustments when replacing inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable, stable performance for precise parting and grooving thanks to secure clamping, a 150 mm overall length and compatibility with MGM 400 indexable inserts; order the holder directly via Metav Werkzeuge or ask our consultants if needed Parting clamp holder MGM 400 L150mm — Grooving clamping holder, 150 mm, for MGM 400 indexable inserts (Teknik Makina) The Parting clamp holder MGM 400 L150mm is a right-hand grooving clamping tool engineered for secure parting and grooving operations in turning centres using MGM 400 indexable inserts 150 mm overall length for deep reach Compatible with MGM 400 indexable inserts Right-hand cutting for standard turning operations Max plunge depth 20 mm for secure parting Improve machining stability and extend insert life The clamping geometry of this holder delivers secure clamping and reduced vibration for consistent cut quality. With an overall length of 150 mm and a 25 mm clamp width and height, the design provides a rigid support that minimises deflection during parting tasks. The 45 mm cutting-head width gives a stable mounting platform for MGM 400 inserts, which helps to prolong insert life and maintain repeatable results across batches. Faster set-up and reliable fastening for production environments Designed for quick assembly and secure fixation, the holder uses an M6x20 Torx screw and a T20 Torx drive together with a 5 mm Allen key for adjustment and replacement. The ISO designation 2525 simplifies fixture planning in production documentation. The measured cutting height of 0.768 mm and a cutting width of 4 mm allow accurate chip formation, while the holder’s compatibility with Korloy inserts ensures straightforward procurement and interchangeability. Purpose-built for parting and grooving in CNC turning This right-hand holder supports a maximum cutting diameter of 110 mm and a maximum plunge depth of 20 mm, making it suited to conventional parting-off and narrow-groove operations. Its compatibility with MGM 400 indexable inserts positions it as a practical choice for shops requiring dependable, repeatable performance. The compact clamping head and standard screw interfaces aid integration into existing tool turrets with minimal adaptation. For tailored tooling solutions and application advice on the Teknik Makina parting clamp holder D831TM, contact Metav Werkzeuge for expert guidance and supply from our Emmerich site Technical data SKU: D831TM Manufacturer: Teknik Makina Type: Parting clamp holder Model designation: Stechklemmhalter MGM 400 L150mm ISO designation: 2525 Core data Overall length: 150 mm Clamp width: 25 mm Clamp height: 25 mm Cutting-head width: 45 mm Maximum cutting diameter: 110 mm Maximum plunge depth: 20 mm Cutting width: 4 mm Cutting height: 0.768 mm Cutting direction: right Features & accessories Compatible with MGM 400 indexable inserts Suitable for inserts by Korloy Torx screw: M6x20 Torx key: T20 Allen key: 5 mm FAQ Which inserts fit this holder? The holder is specified for MGM 400 indexable inserts; it is supplied or recommended to be used with Korloy inserts sized for MGM 400. Is the cutting direction right-hand or left-hand? This tool is configured for right-hand cutting, suitable for standard turning and parting-off cycles. What is the maximum plunge depth for parting operations? The maximum plunge depth is 20 mm, enabling secure parting in a range of workpiece diameters. Which fastening hardware is required for assembly? Assembly uses an M6x20 Torx screw with a T20 key and a 5 mm Allen key for adjustment and locking. Can this holder be used on large-diameter workpieces? The holder supports a maximum cutting diameter of 110 mm, making it appropriate for many standard lathe setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Robust compatibility with MGM 400 indexable inserts and a compact 150 mm overall length deliver secure, vibration‑resistant grooving for right‑hand operations; combine rigidity and precise insert seating for consistent cycle times. Order the grooving clamping holder directly via Metav Werkzeuge or consult our specialists for detailed application advice. Grooving clamping holder MGM 400 L150 mm — right‑hand, Teknik Makina The Grooving clamping holder MGM 400 L150 mm is a right‑hand tool holder for precision grooving and parting tasks, engineered to accept MGM 400 indexable inserts and suited to production and maintenance environments. For MGM 400 indexable inserts 150 mm overall length Right‑hand cutting direction Compatible with Korloy inserts Max cutting diameter 150 mm High‑rigidity clamping for repeatable grooving quality The holder provides a rigid seating for MGM 400 indexable inserts, reducing chatter and improving surface finish in grooving and parting operations. The ISO 2525 designation of the clamping interface ensures standardised insert location; combined with the M6×20 securing screw, this results in reliable insert retention and stable cutting behaviour. Operators benefit from fewer re‑settings and predictable dimensional outcomes, which supports tighter tolerances on serial parts. Compact dimensions for flexible set‑ups and fast handling With an overall length of 150 mm and a compact cross‑section of 25 × 25 mm, the tool is designed for space‑efficient setups in lathe tool posts and turret housings. The cutting‑head width of 45 mm and a cutting width of 4 mm enable narrow grooving operations while maintaining tool stiffness. The tool requires a 5 mm Allen key and a T20 Torx for assembly and insert changes; these standard sizes permit rapid intervention at the machine without specialised tooling, shortening downtime between operations. Compatibility that reduces inventory complexity Specified for MGM 400 inserts and compatible with Korloy manufacturers, the holder simplifies procurement and inventory management by aligning with widely used insert families. A maximum cutting diameter of 150 mm and a maximum grooving depth of 20 mm define its operational envelope, making it suitable for a broad range of turning applications. The right‑hand cutting orientation is optimised for standard turning directions, supporting predictable chip flow and tool life in continuous production. Contact Metav Werkzeuge for tailored application support and order the Teknik Makina grooving clamping holder to streamline grooving processes in the workshop Technical Data SKU: D832TM Label: Grooving clamping holder MGM 400 L150 mm Manufacturer: Teknik Makina eClass: 21181005 Core data Overall length: 150 mm Holder width: 25 mm Holder height: 25 mm Cutting‑head width: 45 mm Max cutting diameter: 150 mm Cutting edge height: 0.776 mm Max grooving depth: 20 mm Cutting width: 4 mm Torx screw: M6x20 Torx key size: T20 Allen key size: 5 mm Special features For MGM 400 indexable inserts Compatible with Korloy inserts Right‑hand cutting direction ISO designation: 2525 Product type: Grooving clamping holder SKU reference: D832TM FAQ Which inserts fit this holder? The holder accepts MGM 400 indexable inserts; compatibility with Korloy insert variants is specified for a streamlined tooling choice. What is the maximum grooving depth? Maximum grooving depth is 20 mm, allowing use in typical parting and grooving tasks within that depth range. Which fasteners and tools are required for insert changes? Insert clamping uses an M6x20 Torx screw; a T20 Torx and a 5 mm Allen key are the standard tools for assembly and adjustment. Is the holder suitable for left‑hand operations? This holder is configured for right‑hand cutting direction; left‑hand operations require a corresponding left‑hand tool holder. What turning diameter is supported? The holder is rated for a maximum cutting diameter of 150 mm, defining its practical use on external turning tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the robust compatibility with MGM 800 indexable inserts and the precise 25 mm clamping geometry for consistent parting and grooving results; the 150 mm overall length and right-hand cutting orientation support stable setups and efficient tool changes — order through Metav Werkzeuge or consult our specialists for exact deployment advice. Stechklemmhalter MGM 800 L150mm — parting clamp holder, right-hand, Teknik Makina The Stechklemmhalter is a right-hand parting clamp holder designed for use with MGM 800 indexable inserts, optimised for precise grooving and parting tasks in industrial turning applications. Compatible with MGM 800 indexable inserts 25 mm clamping width and height Overall length 150 mm Right-hand cutting orientation Precise clamping geometry for stable machining The holder's engineered clamping surfaces deliver a repeatable and rigid connection between tool and insert. With a 25 mm clamping width and matching clamping height, the design reduces micro-movement under cutting loads, which directly improves dimensional accuracy and surface finish. This stability is particularly valuable in operations where narrow parting cuts or deep grooves must be produced reliably, as the tightened interface reduces chatter and extends insert life. Designed for compatibility and fast setup Built to accept MGM 800 indexable inserts and matched to Korloy insert geometries, the tool carrier simplifies inventory and tooling planning. The ISO designation 2525 indicates the standardised shank interface for straightforward mounting in turret systems. The holder uses an M8x22 clamping screw and is tightened with a 6 mm Allen key, enabling quick and secure insert changes that minimise downtime and support continuous production rhythms. Performance benefits for workshop productivity The combination of a 150 mm overall length and a right-hand cutting direction provides flexibility in machine setups while maintaining a compact overhang for reduced deflection. The maximum parting depth of 25 mm and an effective cutting width of 8 mm make this holder suitable for a broad range of parting and grooving tasks. The reduced need for frequent rework and the improved first-pass accuracy contribute to lower cycle times and a measurable boost to operational throughput. Built for everyday industrial use and material versatility Although primarily specified for indexable inserts, the holder's robust construction and clamping concept are intended to support consistent performance across common turning applications. Its design supports typical workshop materials encountered in series production, and the clear specification of mechanical attachment parts ensures that maintenance and replacement are straightforward. Long-term reliability helps maintain production schedules and reduces unscheduled tool changes. For tailored advice on integrating this Teknik Makina parting clamp holder into the production line, or to request the D687-2TM technical datasheet, contact Metav Werkzeuge for personalised consultation and order support. Technical data Article number: D687-2TM ECLASS: 21181005 Label: Stechklemmhalter MGM 800 L150mm Product type: Parting clamp holder Manufacturer: Teknik Makina Facts Overall length: 150 mm Weight: 0.805 kg Clamping width: 25 mm Clamping height: 25 mm Cutting-head width: 25 mm Max parting depth: 25 mm Cutting width: 8 mm Clamping screw: M8x22 Allen key: 6 mm Shank designation: ISO 2525 Cutting direction: right Special features Compatible with MGM 800 indexable inserts Suitable for Korloy inserts Right-hand parting orientation Hardened clamping surfaces Standardised shank interface for turret mounting FAQ What inserts fit this clamp holder? The clamp holder accepts MGM 800 indexable inserts and is specified as compatible with Korloy insert types for straightforward procurement and changeover. What is the maximum parting depth for this tool? The maximum parting depth is 25 mm, as indicated in the product specification for the D687-2TM holder. Which fastening hardware is required for insert clamping? An M8x22 clamping screw is specified and the assembly is tightened using a 6 mm Allen key for reliable insert retention. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid, compact holder that combines precise PHCR 25 insert compatibility with a short set-up time and robust clamping. The 25 mm shank dimensions and 150 mm overall length ensure stable parting operations, while the Torx fastener system (M5x12, T20) simplifies maintenance. Order the holder via Metav Werkzeuge or contact our consultants for matching inserts and application advice. Parting toolholder PHCR 25 L150mm — 25 mm shank, right-hand, Teknik Makina Parting toolholder PHCR 25 L150mm for lathe parting and grooving applications; compatible with PHCR 25 indexable inserts and optimised for right-hand cutting tasks Compatible with PHCR 25 indexable inserts 25 mm shank width and height 150 mm overall length Right-hand cutting direction Boost productivity with secure, low-maintenance clamping A robust clamping design ensures secure clamping of PHCR 25 style inserts, reducing vibration and improving dimensional consistency. The integrated Torx fixation (M5x12) operated with a T20 key permits quick insert changes and repeatable seating height, which shortens downtime during batch changeovers. By prioritising mechanical stability over complex adjustment, the holder supports predictable cycle times and reduces scrap rates in serial turning and parting operations. Achieve consistent finishes and longer tool life The compact 25 mm shank geometry, combined with a 150 mm length, offers a balance between rigidity and accessibility at the toolpost. That stiffness helps maintain cutting edge engagement during right-hand parting cuts, resulting in more consistent surface quality and less flank wear on the insert. For production environments where repeatability is essential, this configuration reduces the need for frequent regrinding and contributes to lower unit costs over extended runs. Simplify tooling logistics and machine set-up Designed for compatibility with ISCAR-sourced PHCR 25 inserts, the holder streamlines inventory and speeds up selection for common parting profiles. The straightforward mechanical design means fewer special tools are required for service, while the moderate mass (0.69 kg) keeps handling simple without compromising stability. For workshops aiming to rationalise tooling assortments, this parting toolholder offers predictable performance with minimal maintenance overhead. For assured compatibility with PHCR 25 indexable inserts and reliable supply from Emmerich, request the Teknik Makina parting toolholder via Metav Werkzeuge or consult our specialists on +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: D976TM Label: Stechklemmhalter PHCR 25 L150mm ECLASS: 21181005 Manufacturer: Teknik Makina Dimensions & weight Overall length: 150 mm Shank width: 25 mm Shank height: 25 mm Weight: 0.69 kg Cutting direction: right Special features Compatible with PHCR 25 indexable inserts Suitable for ISCAR inserts Torx screw: M5x12 Torx key: T20 SKU: D976TM FAQ What inserts fit this holder? The holder accepts PHCR 25 indexable inserts; it is specified for standard PHCR 25 geometries and is compatible with ISCAR supply lines. Is the cutting direction fixed? Yes, the component is configured for right-hand cutting, optimised for conventional lathe parting operations. Which fastener secures the insert? An M5x12 Torx screw secures the insert; the required key is T20, which enables repeatable clamping torque. How does the shank size affect rigidity? The 25 mm shank width and height provide a rigid interface with the toolpost, reducing deflection during parting and improving finish consistency. Can this holder be used in high-production environments? Designed for straightforward maintenance and rapid insert changes, the holder supports high-production routines by limiting downtime and ensuring stable cutting behaviour. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise, vibration‑resistant clamping and simple, secure fastening—ideal for stable right‑hand parting operations with PHCR 25 indexable inserts. Order the holder directly via Metav Werkzeuge or consult our specialists for tailored advice. Stechklemmhalter PHCR 25 L150mm — Parting clamp holder, 150 mm overall length, right‑hand (Teknik Makina) The Stechklemmhalter is a right‑hand parting clamp holder designed for PHCR 25 indexable inserts and optimised for lathe grooving and parting tasks, offering stable clamping and straightforward integration into industrial turning setups Compatible with PHCR 25 inserts 150 mm overall length Right-hand cutting orientation Fastening: T20 / M5x12 Secure clamping for consistent parting quality With a compact clamp profile of 25 mm by 25 mm and an overall length of 150 mm, the holder delivers a stable clamping interface that reduces tool vibration and improves cut consistency. The mass of 0.7 kg contributes to dampening during heavy cuts, so operators benefit from repeatable groove geometry and less tool chatter. This stability translates into fewer rejected parts and a steadier production rhythm. Rapid setup and robust fastening to minimise downtime Fast, reliable mounting is provided by the standard M5x12 Torx screw together with a T20 driver interface, enabling quick insertion changes and secure locking of the indexable insert. The right‑hand cutting orientation is clearly specified to match machine programming and toolpath planning, reducing setup errors. The simple fastening arrangement also lowers maintenance time and eases routine checks, supporting uninterrupted shift work. Broad compatibility that supports efficient workflows Designed for use with PHCR 25 indexable inserts and compatible with inserts from ISCAR, this clamp holder fits seamlessly into existing tool assortments and toolholder families. Manufactured by Teknik Makina, the component is engineered for everyday production demands and can be stocked to ensure rapid replacement. Metav’s supply chain and extensive product range further support continuous operations: a dependable partner with a wide offering and prompt order handling. Contact Metav Werkzeuge for personalised technical advice and to secure Teknik Makina’s D972TM parting clamp holder; reach us at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: D972TM Label: Stechklemmhalter PHCR 25 L150mm Product type: Stechklemmhalter Manufacturer: Teknik Makina Facts Overall length: 150 mm Weight: 0.7 kg Clamp width: 25 mm Clamp height: 25 mm ECLASS: 21181005 Special features For PHCR 25 indexable inserts Compatible with ISCAR inserts Cutting direction: right Torx key: T20 Torx screw: M5x12 FAQ Which indexable inserts fit this holder? The holder is specified for PHCR 25 indexable inserts and is compatible with ISCAR insert types; the item is listed as Stechklemmhalter PHCR 25 L150mm (SKU D972TM) from Teknik Makina. Is the cutting direction right‑hand or left‑hand? This clamp holder is manufactured for right‑hand cutting operations and is marked accordingly for machine setup and tooling programmes. What are the physical dimensions and weight? Overall length is 150 mm with a clamp width and height of 25 mm each; the mass is 0.7 kg, providing a stable platform for parting cuts. What tool is required for installation and which screw is used? Installation uses a Torx T20 driver and an M5x12 screw for secure fastening; the design supports quick, repeatable insert changes for Teknik Makina’s D972TM holder. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, robust solution for lathe parting and grooving: the holder’s 150 mm overall length and 25 x 25 mm cross-section deliver rigidity and repeatable positioning, while the left‑hand cutting orientation and maximum cutting depth of 18 mm support defined process parameters for safe, efficient parting operations. Order or consult via Metav Werkzeuge for expert selection and prompt delivery. Parting Tool Holder L150 mm (D889TM) by Teknik Makina — left‑hand, 25 × 25 mm The Parting Tool Holder L150 mm secures parting and grooving tools for left‑hand cutting on conventional lathes and CNC turning centres, providing a stable platform for controlled chip separation and repeatable component finishing Left-hand cutting orientation 150 mm overall length 25 x 25 mm holder cross-section Maximum cutting depth 18 mm 4 mm cutting width Rigidity and repeatable positioning for secure parting The holder is built around a compact, square shank with a 25 x 25 mm cross-section and 150 mm overall length, giving a stiff mounting that reduces vibration during cut‑off operations. A rigid clamping interface reduces tool flexing, which in turn supports consistent parting results and extends insert life. For process planners, the clear mechanical data — including maximum cutting depth 18 mm and 4 mm cutting width — enables predictable tool engagement and easier cycle‑time calculation. The configuration suits a broad range of turning tasks where precise chip control and secure part separation are required. Fast set‑up and secure clamping to keep the turning centre productive Designed for efficient fixturing, the toolholder uses an M6x20 clamping screw and is adjusted with a 5 mm Allen key, streamlining set‑up and reducing downtime when changing tools. The square shank follows the ISO 2525 size convention (25 × 25 mm), delivering compatibility with standard toolposts and quick‑change adapters. Clear, simple fastening reduces risk of under‑tightening and supports safer operation under load. As a result, workshop throughput benefits from shorter tool change cycles and fewer unexpected interruptions. Practical design focused on workshop integration and process reliability This parting holder is optimised for left‑hand cutting applications, making it suitable for typical lathe setups where the tool moves from the workpiece centre outwards. The compact head width of 25 mm keeps the cutting envelope small, aiding access in confined setups and enabling close‑tolerance grooving close to shoulders or shoulders with minimal interference. The component’s moderate mass (0.735 kg) favours manageable handling while retaining the mass needed to dampen chatter. For production and maintenance teams, the straightforward mechanical concept translates into predictable service life and easy replacement planning. For technical advice or to reserve this Teknik Makina parting tool holder (D889TM), contact Metav Werkzeuge in Emmerich by eMail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss compatibility with existing toolposts and turning cycles. Technical data SKU: D889TM Product type: Parting tool holder Brand: Teknik Makina eClass: 21181005 Facts Overall length: 150 mm Weight: 0.735 kg Holder width: 25 mm Holder height: 25 mm Cutting head width: 25 mm Cutting width: 4 mm Maximum parting depth: 18 mm Clamping screw: M6x20 Special features Left-hand cutting direction ISO 2525 compatible (25 × 25 mm) Adjustment: 5 mm Allen key Category: Machining > Clamping holders FAQ What operations is this holder intended for? The holder is intended for parting and grooving operations on lathes and CNC turning centres; the Parting Tool Holder L150 mm (D889TM) is optimised for controlled cut‑off and narrow grooving tasks. Is the cutting direction left or right? This toolholder is configured for left‑hand cutting, matching applications where the tool advances from the workpiece centre towards the outer diameter. What is the maximum cutting depth and cutting width? The maximum cutting depth is 18 mm and the cutting width specified is 4 mm, giving clear limits for tool engagement planning. Which fastening and adjustment tools are required? Set‑up and tightening are performed with an M6x20 clamping screw and a 5 mm Allen key, enabling quick and secure clamping. Which mounting standard does the shank follow? The shank follows the ISO 2525 size convention with a 25 × 25 mm cross‑section, ensuring compatibility with standard toolposts and quick‑change systems. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise parting performance and a compact, robust clamp design — compatible with Walter GX16 inserts and featuring a 25 mm clamping height for stable cuts. Order the D859TM directly via Metav Werkzeuge or consult our specialists for application advice. D859TM parting tool holder — 25 mm clamping height, 2 mm cutting width (Teknik Makina) A D859TM parting tool holder engineered for secure clamping of GX16 indexable inserts, intended for accurate parting and grooving operations in turning applications. 25 mm clamping height Accepts GX16 indexable inserts 2 mm cutting width for fine slots 150 mm overall length, 0.403 kg Consistent clamping for repeatable parting quality The holder delivers a stable clamping interface thanks to its 25 mm clamping height and 25 mm body dimensions, which reduce tool flex and vibration during cut-off operations. This stability translates directly into improved surface finish and reduced rework, especially when working with narrow grooves where a 2 mm cutting width is required. The ISO 2525 designation indicates a standardised shank profile that simplifies integration into existing toolposts and quick-change systems, lowering setup time and improving through-put without sacrificing accuracy. Broad compatibility to simplify tooling choices Built to accept GX16 indexable inserts and specified for Walter insert geometry, the holder supports a familiar insert family so that procurement and inventory management remain efficient. The toolholder’s compatibility with the 2C GX16 bar designation enables use with standard parting bars and mounting systems, providing flexibility across small-batch and serial production runs. This compatibility reduces the need for special inserts, helping to streamline tooling logistics while maintaining consistent cutting performance. Compact, balanced design for easy handling and robust performance With a total length of 150 mm and a mass of 0.403 kg, the unit is compact enough for tight lathe setups yet heavy enough to dampen chatter during aggressive cuts up to the specified max cutting depth of 18 mm. The clamp-style fixing secures the insert reliably while permitting quick insert changes, which supports lean workshop routines and lowers machine downtime. For machining specialists seeking predictable results from parting and grooving operations, this holder offers a practical balance of rigidity, accessibility and minimal footprint on the toolpost. For precision parting with proven compatibility, contact Metav Werkzeuge to discuss the D859TM parting tool holder and suitable GX16 inserts — Metav Werkzeuge can advise on integration and supply from Emmerich: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: D859TM Manufacturer: Teknik Makina ISO designation: 2525 Fits indexable inserts: GX16 (Walter) Facts Clamping height: 25 mm Head width: 25 mm Body width: 25 mm Cutting width: 2 mm Max cutting depth: 18 mm Overall length: 150 mm Weight: 0.403 kg Special features Bohrstange designation: 2C GX16 Compatible with Walter GX16 inserts Clamp-style parting holder Designed for turning parting and grooving applications FAQ What insert type does the holder accept? The D859TM accepts GX16 indexable inserts and is specified for compatibility with Walter GX16 geometries. What are the key dimensions to check for machine fitment? Check the 25 mm clamping height, 150 mm overall length and ISO 2525 shank form when integrating the holder into a toolpost or quick-change block. How deep can the D859TM cut in one pass? The holder is specified with a maximum parting depth of 18 mm, which defines its recommended maximum cutting engagement for stable operation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

A compact combination of 4 mm cutting width, 25 x 25 mm shank profile and a 22 mm maximum parting depth delivers reliable, repeatable cuts for workshop turning operations; order the parting tool holder directly via Metav Werkzeuge or consult the technical advisors for tailored application support. Parting Tool Holder (Stechklemmhalter) — 4 mm cut width, right-hand, Teknik Makina A robust Parting Tool Holder for right-hand cut-off and grooving tasks on lathe applications, designed for secure clamping of indexable inserts and stable performance in short overhang setups. 4 mm cutting width for precise parting Right-hand orientation for standard turning setups 25 x 25 mm shank profile for rigid mounting Compatible with Horn indexable inserts High-precision cutting where consistency matters The Teknik Makina parting tool holder is engineered for dependable parting and grooving operations, combining a slim 4 mm cutting width with a 25 x 25 mm block profile to reduce vibration and ensure repeatable results. The holder’s geometry is optimised to support a clean chip flow and steady cut, which translates into lower scrap rates and consistent cycle times. For workshops aiming to raise process reliability, the compact design allows close control of chip formation while maintaining a short overhang for improved rigidity. Secure clamping and controlled cutting depth Clamping stability is provided by a solid clamping system that matches the ISO designation 2525, offering straightforward insert seating and dependable retention under intermittent loads. The tool accepts standard indexable inserts from Horn, enabling quick replacement and straightforward inventory management. With a maximum parting depth of 22 mm, the holder supports most common cut-off tasks without compromising stiffness. The moderate mass of 0.705 kg contributes to stable dynamics on the toolpost, aiding surface finish and dimensional control. Compatibility engineered for workshop efficiency Designed to mate with bores and adaptors in the 4C-R S229 series, this holder fits existing clamping arrangements and slot systems, reducing setup time when retrofitting or scaling production. The right-hand cutting direction suits conventional turning centres and ensures predictable chip evacuation. Compatibility with widely used insert systems simplifies procurement and keeps tooling costs transparent, supporting a pragmatic cost-benefit approach in production planning. Practical dimensions and handling benefits With an overall length of 150 mm and a compact 25 mm head and body width, the holder is suited to confined toolpost spaces and multi-station arrangements. The balanced proportions minimise interference with adjacent tools while delivering sufficient reach for effective parting. The combination of a standardised shank, ISO alignment and recognised insert compatibility allows flexible deployment across small-batch engineering to medium-volume machining, promoting workflow continuity and fewer changeovers. For purchasing enquiries or detailed application advice regarding the Teknik Makina parting tool holder (SKU D694TM), contact Metav Werkzeuge for a personalised quotation and technical consultation via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: D694TM Manufacturer: Teknik Makina Designation: Stechklemmhalter Eclass: 21181005 Facts Shank height: 25 mm Shank width: 25 mm Cutting head width: 25 mm Cutting width: 4 mm Max parting depth: 22 mm Overall length: 150 mm Weight: 0.705 kg Cutting direction: right Special features ISO designation: 2525 Compatible inserts: Horn Bohrstange designation: 4C-R S229 Right-hand orientation Robust clamping for indexable inserts FAQ What insert types fit this holder? The holder accepts standard indexable inserts specified by Horn; compatibility is indicated in the product data for the Teknik Makina parting tool holder (Stechklemmhalter), SKU D694TM. Is the holder suitable for deep grooving operations? This cut-off holder is designed for a maximum parting depth of 22 mm, making it suitable for typical grooving and parting tasks within that range. Can the holder be mounted on standard 25 x 25 mm toolposts? Yes, the compact 25 x 25 mm shank profile is intended for rigid mounting on standard toolposts and fixtures commonly used in turning centres. Does the orientation allow left-hand cutting? The supplied configuration is for right-hand cutting direction; left-hand variants would require a different orientation or alternative holder. How does the holder support workshop efficiency? By using standardised ISO seating (2525) and compatibility with Horn inserts, the parting tool holder reduces tool-change time and simplifies tooling stock management. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining the right‑hand cutting orientation, a 4 mm maximum cutting width and a rigid 25 mm clamp height, the D777TM delivers stable, repeatable parting and grooving results; order this tool via Metav Werkzeuge or consult our specialists for application guidance. Parting and Grooving Tool Holder D777TM — Right‑hand, 4 mm cutting width (Teknik Cutting Tools) The Parting and Grooving Tool Holder D777TM is a right‑hand clamp holder engineered for precision parting and grooving tasks using 4C DGN indexable inserts in modern turning centres Right‑hand cutting orientation 4 mm maximum cutting width Compatible with 4C DGN inserts (ISCAR) 150 mm overall length for deep cuts Consistent, high‑precision parting and grooving The D777TM is designed to deliver repeatable results on series turning operations through its defined right‑hand geometry and narrow cutting capacity. The 4 mm cutting width is optimised for typical parting and shallow grooving applications, enabling accurate control of the cut and predictable chip formation. By using standard 4C DGN indexable inserts, the holder combines proven insert technology with a compact clamping system, which reduces setup variation and supports stable diameter control on finished components. Robust clamp design for reduced vibration and improved tool life A compact clamping body with nominal dimensions of 25 mm height and 25 mm width gives the holder a rigid interface between toolpost and insert head. The resulting torsional stiffness lowers deflection during engagement and thus reduces the risk of chatter when performing plunge cuts of up to 20 mm. The tool’s mass of 0.709 kg contributes to damped cutting dynamics without compromising rapid tool changes, helping to extend insert life and maintain consistent surface quality across batches. Ready for straightforward integration into existing toolsets Produced to the ISO designation 2525 and compatible with the 4C‑R DGN boring bar family, the D777TM fits established workshop toolholders and quick‑change systems. Compatibility with ISCAR‑type inserts ensures access to a broad range of grades and chipbreaker geometries suited to different materials and cutting conditions. The straightforward clamp arrangement and standardised interface shorten setup times and simplify inventory management, making this holder a practical choice for workshops seeking consistent performance with minimal adaptation. Practical applications and operational benefits Ideal for turning centres and lathes where precise parting or groove generation is required, the holder supports controlled plunging and lateral cuts within its dimensional limits. The 150 mm overall length provides reach for deeper features while keeping overhang acceptable for general turning work. By pairing the holder with the appropriate insert grade, operators can balance economy and performance, achieving efficient material removal and stable edges on components destined for assembly or further processing. Contact Metav Werkzeuge for procurement and technical guidance on the Teknik Cutting Tools D777TM — available from Emmerich with reliable supply and application advice Technical Data Article number: D777TM Manufacturer: Teknik Makina Designation: Parting and grooving tool holder (Stechklemmhalter) SKU: D777TM Facts Overall length: 150 mm Cutting width: 4 mm Maximum plunge depth: 20 mm Clamp height: 25 mm Cuthead width: 25 mm Body width: 25 mm Weight: 0.709 kg Special features Compatible inserts: 4C DGN Compatible insert manufacturer: ISCAR ISO designation: 2525 Compatible boring bar: 4C‑R DGN Cutting direction: Right‑hand FAQ What cutting direction is the holder designed for? The holder is configured for right‑hand cutting; the D777TM operates with a right‑hand feed and geometry for standard lathe setups. Which inserts fit this tool holder? The tool holder accepts 4C DGN indexable inserts and is specified for ISCAR‑compatible grades. What is the maximum plunge depth for parting operations? The holder supports a maximum plunge depth of 20 mm, as indicated in the technical data for stable parting passes. Is the D777TM compatible with quick‑change boring bars? Yes — the holder is compatible with the 4C‑R DGN boring bar designation and standardised interfaces. How long is the holder and how does this affect overhang? With an overall length of 150 mm, the D777TM provides reach for deeper grooves while maintaining acceptable rigidity for general turning tasks. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust right-hand parting solution that combines dependable clamping, compatibility with ZCC 5C ZT.D inserts and a compact 25 × 25 mm head for consistent chip control — ideal for short-run and repeat production. Order directly via Metav Werkzeuge or consult our specialists for application-specific advice. Stechklemmhalter — Right-hand parting and grooving clamp holder, 25 × 25 mm, Teknik Makina The Stechklemmhalter is a right-hand parting and grooving clamp holder engineered for lathe turning, offering a compact 25 mm clamping head and compatibility with standard ZCC inserts for routine workshop and industrial applications. Right-hand cutting for controlled parting Compatible with 5C ZT.D ZCC inserts 25 x 25 mm clamping head dimensions 150 mm overall length for stable reach Improved parting accuracy through stable clamping The holder’s 25 x 25 mm clamping head and secure insert seat deliver consistent support during cut-off and grooving tasks, reducing tool chatter and improving repeatability. With a cutting width of 5 mm and a maximum grooving depth of 18 mm, the design is focused on controlled material separation and reliable chip formation. These measurable parameters enable process planners to match the tool to the required cut profile, lowering scrap rates and reducing rework in production. Seamless integration with industry-standard inserts and bars Designed for compatibility with 5C ZT.D inserts from ZCC and to fit a 5C-R ZT-D bar designation, the holder streamlines tooling logistics by using widely available components. The ISO-style designation 2525 indicates the holder geometry and clamping interface, simplifying procurement and ensuring correct replacement parts. Right-hand cutting orientation provides predictable chip flow to the operator’s left, which is essential when setting up tool paths and guard arrangements on conventional and CNC lathes. Practical handling and production benefits for small and medium runs At an overall length of 150 mm and a mass of 0.734 kg, the holder balances rigidity with manageable handling during set-up, allowing quick changes at the turret and reliable stability during the cut. The compact footprint supports tight chuck work and short overhangs, which helps maintain concentricity and reduces vibration. For workshops seeking consistent parting performance, the combination of defined geometric values and straightforward compatibility improves throughput and operational confidence. Contact Metav Werkzeuge for tailored tooling advice and availability, or call +49 2822 7131930 to discuss the best holder configuration for specific machining tasks. Technical data Article number: D046TM Manufacturer: Teknik Makina Model / designation: Stechklemmhalter ISO designation: 2525 Compatible inserts: 5C ZT.D (ZCC) Core specifications Cutting direction: right Holder height: 25 mm Head width: 25 mm Holder width: 25 mm Cutting width: 5 mm Max grooving depth: 18 mm Overall length: 150 mm Weight: 0.734 kg Features / compatibility Compatible with ZCC inserts For use with 5C-R ZT-D bar Right-hand parting and grooving application FAQ Which inserts fit this holder? The holder accepts ZCC 5C ZT.D type inserts; the designation is stated in the technical data for the D046TM part. What is the maximum grooving depth? The maximum grooving (stepping) depth is 18 mm, suitable for typical parting and grooving tasks within that range. Is this holder right- or left-hand? This toolholder is configured for right-hand cutting, providing standard chip evacuation direction for many lathe set-ups. What are the key dimensions for set-up planning? Key values are 25 mm clamping head dimensions, 5 mm cutting width and 150 mm overall length, useful for turret and chuck clearance calculations. Which clamping bar does it require? The holder is specified to work with a 5C-R ZT-D bar designation, matching common bar types used with this interface. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from robust clamping, compatibility with MGM 800 indexable inserts and a 150 mm overall length for reliable deep parting — ideal where repeatable results and short tool-change cycles matter. Order the Stechklemmhalter MGM 800 L150mm directly via Metav Werkzeuge or ask our consultants if needed. Stechklemmhalter MGM 800 L150mm — left-hand parting tool holder by Teknik Makina The Stechklemmhalter MGM 800 L150mm is a left-hand parting and grooving holder designed for use with MGM 800 indexable inserts, delivering secure clamping and consistent cutting performance in turning applications. Parting holder for MGM 800 indexable inserts Left-hand cutting direction for specialised operations 150 mm overall length for deep parting 25 mm clamping width and 25 mm head width Consistent cycle-time reduction through secure clamping and stability The holder is engineered to provide stable clamping and minimise vibration during parting operations, which improves surface finish and reduces reject rates. With a 25 mm clamping width and a 25 mm cutting-head width, the geometry supports lateral rigidity — beneficial for long runs and batch production. The mass and balance of the unit, at approx. 0.746 kg, contribute to steady chip formation and repeatable cut quality, helping to shorten machining cycles and lower overall production variability. Quick insert changes and straightforward maintenance to keep the line running Designed for efficient servicing, the parting tool holder uses an M8x22 clamping screw accessible with a 6 Allen key, enabling fast insert replacement and secure seating of the indexable insert. The ISO 2525 designation clarifies mounting dimensions for toolpost compatibility and simplifies integration into existing setups. Faster changeover reduces downtime and supports predictable throughput — a practical gain for small-series and continuous production alike. Clear compatibility and defined cutting parameters for planning operations This holder accepts Korloy-sourced MGM 800 indexable inserts, with a maximum parting depth of 25 mm and a cutting width of 8 mm, making it suitable for standard parting‑off and narrow‑grooving tasks on turning centres. The left-hand cutting orientation makes the holder appropriate for operations where tool approach and spindle direction require a mirrored configuration. The SKU D621-2TM identifies the exact variant for procurement and inventory control, aiding procurement teams in maintaining consistent tooling across multiple machines. For reliable parting performance from Teknik Makina and procurement support from Metav Werkzeuge, contact Metav Werkzeuge GmbH for ordering and technical advice — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: D621-2TM eClass: 21181005 Product type: Parting tool holder (Stechklemmhalter) Manufacturer: Teknik Cutting Tools Overall length: 150 mm Weight: 0.746 kg Clamping width: 25 mm Head width: 25 mm Maximum parting depth: 25 mm Cutting width: 8 mm Cutting direction: left Clamping screw: M8x22 Allen key: 6 Allen ISO designation: 2525 Compatible inserts: MGM 800 indexable inserts Recommended insert manufacturer: Korloy Application: Parting and narrow grooving SKU for ordering: D621-2TM FAQ Which inserts are compatible with this holder? This parting tool holder is compatible with MGM 800 indexable inserts and is specified for use with inserts from Korloy. What is the maximum parting depth? The holder supports a maximum parting depth of 25 mm, suitable for standard parting and narrow‑grooving tasks. How is the insert clamped and changed? Insert clamping is secured with an M8x22 screw that is operated using a 6 Allen key, allowing quick and reliable insert changes. Is the cutting direction left-hand or right-hand? The tool is supplied in a left-hand configuration, intended for operations requiring that orientation. What are the key dimensions to check for toolpost compatibility? Key dimensions include the 150 mm overall length, 25 mm clamping and head widths, and the ISO 2525 designation for mounting compatibility. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, robust holder that combines a 3 mm cutting width with a 22 mm maximum grooving depth for precise parting and grooving operations. Rely on the secure clamp design and the 25 x 25 mm shank for stable cuts; order directly via Metav Werkzeuge or consult the technical team for integration support. Parting and grooving toolholder D711TM — left‑hand, 3 mm cutting width (Teknik Makina) The Parting and grooving toolholder D711TM is a left‑hand parting and grooving toolholder optimised for indexable Horn inserts, offering a compact 25 x 25 mm shank and a 150 mm overall length for stable lathe operations. Left‑hand parting and grooving direction 3 mm cutting width for narrow grooves Max grooving depth 22 mm 25 x 25 mm shank for secure clamping Improved cycle stability through narrow cutting geometry The holder’s 3 mm cutting width and defined seating for indexable inserts deliver consistent chip control and reduced tool interference. With a 22 mm maximum grooving depth, the design supports common parting tasks and narrow‑groove finishing without unnecessary overhang. This targeted geometry reduces rework and contributes to predictable cycle times on CNC lathes, which is particularly valuable for high‑mix, medium‑volume production where process stability translates directly into lower scrap rates and fewer set‑ups. Secure clamping and rigid shank for repeatable accuracy A square shank of 25 x 25 mm and a 150 mm overall length balance accessibility and stiffness to minimise vibration during heavy‑duty cuts. The robust clamp mechanism ensures positive insert retention and repeatable seating, improving surface finish and dimensional repeatability. At a weight of 0.7 kg, the toolholder keeps inertia low while providing sufficient mass for dampening. These characteristics make the holder suitable for both roughing parting cuts and controlled finishing passes where consistent tool behaviour is required. Seamless integration with indexable inserts and bar systems Designed to accept Horn indexable inserts and specified as ISO 2525, the toolholder references common industry standards for straightforward tool management. The bar designation 3C‑L S229 indicates compatibility with standard bar holders and simplifies replacement within existing tool sets. Integration of this holder into a modular tooling strategy reduces machine downtime during tool swaps and supports efficient inventory management through standardised insert types and ISO referencing. Contact Metav Werkzeuge for application advice and reliable delivery of the Teknik Makina D711TM — specialist support is available from Emmerich to ensure the right configuration for the machining task Technical data Article number: D711TM Name: Parting and grooving toolholder Manufacturer: Teknik Makina Facts Cutting width: 3 mm Max grooving depth: 22 mm Shank height: 25 mm Shank width: 25 mm Head width: 25 mm Overall length: 150 mm Weight: 0.7 kg Special features Left‑hand cutting direction ISO designation: 2525 Compatible with Horn indexable inserts Bar designation: 3C‑L S229 FAQ What insert types fit this toolholder? The D711TM accepts indexable inserts compatible with Horn systems; the holder is specified for standard Horn insert geometries and referenced by ISO 2525. Is the cutting direction suitable for common lathe setups? Yes, the toolholder is configured for a left‑hand cutting direction, matching left‑hand parting and grooving operations on conventional and CNC lathes. How deep can this holder cut in a single pass? The maximum grooving depth is 22 mm, which is suitable for most parting and narrow‑groove applications within this toolholder class. What shank size is required in the turret or bar adapter? A 25 x 25 mm shank accommodates the holder and provides the clamping profile necessary for secure mounting in standard turrets or bar adaptors. Can the holder be used for finishing as well as roughing? The combination of a rigid 25 x 25 mm shank and the precise seat for indexable inserts enables both stable roughing and controlled finishing passes when matched with the appropriate insert grade and geometry. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid clamping design combined with internal coolant and a precision 95° cutting angle for consistent left‑hand turning performance; order the clamping holder directly via Metav Werkzeuge or consult our specialists for workplace integration. PWLNL 2525 clamping holder – left‑hand turning toolholder with internal coolant (Teknik Makina) The PWLNL 2525 clamping holder is a left‑hand turning toolholder engineered for WNMG 0604 indexable inserts, offering internal coolant delivery and a compact 150 mm overall length for workshop and CNC lathe applications Left‑hand turning holder, 95° cutting angle For WNMG 0604 indexable inserts Internal coolant supply 150 mm overall length, 30 mm cutting height Consistent clamping and dimensional stability for repeatable turning The toolholder delivers a rigid clamping principle that reduces vibration and runout during interrupted cuts. Its ISO designation PWLNL 2525 denotes a standardised shank and clamping geometry compatible with commonly used turning toolposts, which simplifies tool changeover and inventory. The specified cutting height of 30 mm and 95° cutting angle ensure the insert sits in a predictable orientation, improving dimensional repeatability on turned parts and reducing scrap rates in batch production. Improved cooling and chip control for longer insert life Built‑in internal coolant channels direct cutting fluid close to the cutting edge, supporting heat control and chip evacuation when machining steels and alloys. Supplying coolant through the holder lowers flank and crater wear on the insert, which translates into extended insert life and fewer tool changes per shift. For shops upgrading from external coolant setups, the integrated feed reduces the need for manual coolant alignment and supports consistent cutting conditions across serial runs. Workshop efficiency and straightforward integration into existing setups At 150 mm overall length and a compact head width of 32 mm, the holder is sized for both confined toolposts and heavier turning applications, offering a balance between reach and rigidity. The clamping system uses a TH617 clamping screw with accessory parts such as TA021 shim plate and TS3 dowel pin, enabling quick assembly and secure seating of WNMG 0604 inserts. The left‑hand configuration and standardised mount allow predictable set‑up times, contributing to faster machine changeovers and higher uptime on multi‑operation shop floors. Choose the Teknik Makina PWLNL 2525 for robust left‑hand turning with integrated coolant — contact Metav Werkzeuge for tailored advice and ordering at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: AP166TM Manufacturer: Teknik Makina Designation: PWLN for WNMG Indexable Inserts ISO designation: PWLNL 2525 Cutting direction: left Internal coolant: yes Cutting angle: 95° Facts Overall length: 150 mm Cutting height: 30 mm Holder height: 25 mm Head width: 32 mm Holder width: 25 mm Weight: 0.756 kg Suitable insert: WNMG 0604 Special features Clamping screw: TH617 Shim / support plate: TA021 Dowel pin: TS3 Knee lever: TL3 Allen key: 2.5 Allen Bore bar designation: M06-IKG1/8 Left‑hand turning configuration Internal coolant supply FAQ What inserts fit this holder? The holder is specified for WNMG 0604 indexable inserts; the PWLNL 2525 geometry secures the standard WNMG shape and size for reliable seating. Is coolant fed through the holder? Yes, the PWLNL 2525 features internal coolant, allowing fluid to reach the cutting edge and improving tool life and chip control. Can the holder be mounted on standard toolposts? The ISO designation and compact shank of the PWLNL 2525 are intended for standard turning toolposts and offer straightforward integration into existing lathe setups. Which spare parts are associated with the clamping system? Associated parts listed for the holder include TH617 clamping screw, TA021 shim plate, TS3 dowel pin and TL3 knee lever, which facilitate secure assembly and maintenance of the clamping interface. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise geometry and reliable compatibility: the compact parting blades deliver stable cutting at a 32 mm blade height with a narrow 1.65 mm blade width, while the 150 mm length and 36 mm maximum cutting depth support secure engagement in production lathes. Order the parting blade directly via Metav Werkzeuge or consult our specialists for integration advice. Parting blades KL34TM — precision parting blade, 32 mm height, for KGMN 200 inserts (Teknik Makina) The Parting blades KL34TM are designed for precision parting and grooving on CNC and manual lathes, compatible with KGMN 200 indexable inserts for efficient chip control and consistent results 32 mm blade height for secure clamping Compatible with KGMN 200 inserts (Korloy) 36 mm maximum cutting depth for deeper cuts 1.65 mm blade width for narrow kerf and material savings Stable geometry for efficient parting and grooving The KL34TM parting blade features a 32 mm blade height and 25 mm cutting height, engineered to provide a rigid interface between toolholder and insert. This geometry reduces vibration and improves dimensional stability during cut-off and grooving operations, so the risk of chatter is decreased and finish quality is improved. With a 1.65 mm blade width, material removal is optimised for minimal waste while maintaining sufficient flute clearance. The combination of these dimensions supports higher feed rates where the process permits and contributes to predictable cycle times, which is essential for production planning in job shops and small-scale manufacturing. Quick set-up and predictable tool performance Designed for indexable inserts of the KGMN 200 family, the blade simplifies tooling logistics: inserts from Korloy fit directly, reducing changeover complexity and inventory variety. The overall length of 150 mm gives adequate reach for a variety of setups, while the specified holder depth of 36 mm ensures secure seating and reliable clamping in compatible toolposts or holders. This clarity of interface enables faster machine set-up and helps maintain process repeatability, so teams can focus on throughput rather than troubleshooting tooling interfaces. For operators new to parting tools, the straightforward compatibility and defined dimensions make integration into existing tool libraries uncomplicated. Less rework, more consistent results for workshops A narrow kerf and robust blade height combine to lower scrap rates by reducing workpiece deflection at the cut-off zone. The design suits both single-item prototyping and small-series production where material conservation and surface condition matter. For those seeking an easy-to-understand technical specification, parting is the process of cutting a finished contour free from the parent material; these blades provide the mechanical stability required to achieve that with minimal post-process finishing. Backed by Teknik Makina’s manufacturing standards, the component supports continuous operation and predictable wear characteristics, contributing to lower downtime and a more reliable production flow. Contact Metav Werkzeuge today to discuss Teknik Cutting Tools KL34TM parting blades for a suitable holder configuration — call +49 2822 7131930 or email info@metav-werkzeuge.com to clarify fitment and delivery options Technical data SKU: KL34TM Brand: Teknik Makina Suitable for inserts: KGMN 200 Compatible insert manufacturer: Korloy Dimensions Blade height: 32 mm Cutting height: 25 mm Blade width: 1.65 mm Length: 150 mm Maximum cutting depth (holder): 36 mm Compatibility and features For parting and grooving applications Indexable-insert system Narrow kerf design for reduced material loss Designed for secure clamping in compatible holders FAQ What insert type fits this blade? The KL34TM parting blade is designed for KGMN 200 indexable inserts; Korloy inserts in that designation are a direct match. Which operations is this blade intended for? This blade is intended for parting (cut-off) and grooving tasks on CNC and manual lathes where a narrow kerf and stable geometry are required. How does blade width affect material savings? A 1.65 mm blade width reduces the kerf compared with wider tools, lowering material loss and often reducing cycle energy per parted component. Can this blade be used in high-production environments? Yes, the KL34TM’s rigid profile and standard insert compatibility support repeatable use in serial production provided proper clamping and cooling practices are observed. What is the maximum practical cutting depth? The blade specification lists a maximum cutting depth of 36 mm for the holder seating; actual achievable depth depends on machine capability and holder design. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com