Gibt es einen Hahn und Kolb Online Shop?

Combine stable clamping with quick insert changes and compatibility for ENMX 0604 indexable inserts to maintain steady throughput on milling operations; the robust 20 mm shank and three cutting edges support repeatable performance. Order the Shaft milling cutter S108TM directly via Metav Werkzeuge or ask the consultants if needed. Shaft milling cutter S108TM — 20 mm shank, for ENMX 0604 indexable inserts (Teknik Makina) A precision shaft milling cutter S108TM designed for use with ENMX 0604 indexable inserts, intended for medium-duty milling where stability and fast insert replacement are priorities. 20 mm shank diameter for stable clamping Compatible with ENMX 0604 indexable inserts Three cutting edges for balanced cutting M2.5x7 Torx fixing screw, T8 key Consistent rigidity for accurate machining and reduced vibration The tool’s 20 mm shank is engineered to deliver stable clamping in conventional collets and toolholders, which translates into reduced vibration and improved surface finish. Rigidity during milling minimises chatter and contributes to longer insert life; this means fewer interruptions and more predictable component tolerances. By choosing a cutter with a substantial shank diameter and balanced geometry, machining cycles become more reliable, particularly on operations where dimensional repeatability is essential. Fast insert changes and secure fixing to save production time Compatibility with ENMX 0604 indexable inserts enables rapid insert swaps; the M2.5x7 Torx fixing screw and supplied T8 key secure each insert positively for safe, repeatable clamping. The tool features three cutting edges, which provide a compromise between chip evacuation and cutting stability; this geometry reduces toolholder loads while maintaining effective material removal. For workshops that run medium-volume production or mixed batches, the simplified insert handling lowers downtime and streamlines tool management. Designed for predictable tool life and straightforward service With an overall length of 130 mm and a cutting diameter of 20 mm, the cutter balances reach with stiffness, making it suitable for face and light shoulder milling tasks where access is required without sacrificing control. The tool’s construct reduces the frequency of regripping and recalibration, supporting consistent cycle times and easier scheduling. Supplied data indicate direct compatibility with inserts from YG-1, which helps to align procurement and stock management for faster replenishment and fewer production holds. Contact Metav Werkzeuge for tailored application advice and to secure the S108TM shaft milling cutter for reliable production — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: S108TM Manufacturer: Teknik Makina Article: Shaft milling cutter For indexable inserts: ENMX 0604 Compatible insert maker: YG-1 Dimensions & core data Diameter: 20 mm Shank / clamping diameter: 20 mm Overall length: 130 mm Cutting edges: 3 Fixing screw: M2.5x7 Torx key: T8 Eclass: 21180806 ETIM: EC011860 Special features & materials Designed for ENMX 0604 indexable inserts Three-flute design for balanced cutting Positive Torx fixation for secure insert clamping Brand: Teknik Makina FAQ Which insert type fits the cutter? The cutter is designed for ENMX 0604 indexable inserts, allowing direct use of those plates in the S108TM for predictable cutting geometry. Is the tool compatible with YG-1 inserts? Yes, compatibility with YG-1 inserts is indicated; the S108TM accepts ENMX 0604 inserts produced by that manufacturer. What are the key dimensions to check for toolholder fit? Relevant dimensions are the 20 mm shank diameter and the 130 mm overall length; these determine clamping compatibility and reach. How is the insert secured in the cutter? Inserts are fastened using an M2.5x7 Torx screw; a T8 key is specified for secure tightening and reliable repeatability. For which applications is this cutter best suited? The tool is suitable for medium-duty milling tasks where a balance of stiffness, accessible reach and fast insert changes are required; typical uses include face milling and light shoulder operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of high rigidity, quick insert changeover and compact dimensions for consistent machining results; order the cutter via Metav Werkzeuge or consult our specialists for application advice. Shank milling cutter S030TM — 20 mm shank, for APMT 0602 indexable inserts by Teknik Makina Shank milling cutter S030TM designed for indexable APMT 06 inserts, engineered for reliable insert clamping and repeatable results in production toolrooms 20 mm shank diameter For APMT 06 indexable inserts 30 mm cutting height Requires T6 Torx key Engineered stiffness for steady, predictable machining The S030TM is built around a 20 mm shank and a 120 mm overall length, a combination that balances accessibility with rigidity to reduce chatter and maintain surface quality. With 5 cutting edges and a 30 mm cutting height, the tool enables efficient material removal while keeping tool deflection low; the 90° cutting angle supports square shoulder machining and predictable corner geometry. The modest mass (0.26 kg) helps preserve spindle dynamics, especially in medium-duty milling tasks, so cycle times stay stable and repeatability improves. Quick insert changes and secure clamping minimise downtime This milling cutter accepts APMT 06 indexable inserts and is compatible with Korloy inserts, allowing standardised inventory and rapid on-machine servicing. The insert is secured with a M1.8x4.1 Torx screw tightened with a T6 key for toolroom-standard clamping torque and repeatable seating. Indexable inserts are small, replaceable carbide tips that can be rotated or renewed without regrinding a whole tool body — a cost-efficient approach that reduces tooling waste and simplifies workshop logistics while keeping machining precision high. Practical fit for modern workshops and CNC setups Designed by Teknik Makina, the cutter's 20 mm diameter and compact 120 mm length make it straightforward to integrate into milling spindles and modular tool holders. The consistent geometry of indexable tooling supports predictable process planning and shorter setup intervals. For shops seeking reliable insert tooling with straightforward maintenance, this cutter delivers a compact footprint, standard fastening hardware and compatibility with widely available APMT 06 inserts — features that collectively support higher machine utilisation and fewer unplanned stoppages. Contact Metav Werkzeuge for application guidance on the Teknik Makina S030TM shank milling cutter and fast supply — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: S030TM Manufacturer: Teknik Makina Suitable for inserts: APMT 06 Compatible insert manufacturer: Korloy Core data Shank diameter: 20 mm Cutter diameter: 20 mm Cutting height: 30 mm Overall length: 120 mm Cutting angle: 90° Number of cutting edges: 5 Weight: 0.26 kg Special features Torx screw: M1.8x4.1 Torx key size: T6 For APMT 0602 indexable inserts SKU: S030TM FAQ What inserts does this cutter accept? The shank milling cutter S030TM accepts APMT 06 indexable inserts and is compatible with Korloy APMT 06 grades. How are the inserts secured and which key is required? Inserts are held with a M1.8x4.1 Torx screw; a T6 Torx key is used for tightening and removal on the S030TM. Is the S030TM suitable for high-speed machining? The S030TM is designed for stable, repeatable milling with indexable inserts; compatibility with high-speed applications depends on machine capability and chosen insert grade. Can the cutter be used with inserts from other manufacturers? The S030TM is specified for APMT 06 format inserts; interchangeable inserts from other manufacturers that match this format and seat geometry can be used provided clamping and seat fit are correct. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of ANHX 1004–1206 insert compatibility, a 20 mm shank and a 30 mm cutting length for consistent, productive milling results; order the tool directly via Metav Werkzeuge or consult our specialists for application guidance. Shank cutter S783TM – 20 mm shank, for ANHX 1004–1206 indexable inserts | Teknik Makina A Shank cutter S783TM engineered for indexable-insert milling, offering secure insert clamping and a compact cutting length for precision pocketing and shoulder milling in CNC operations 20 mm shank for rigid toolholding Compatible with ANHX 1004–1206 inserts Three cutting edges for balanced cutting 160 mm overall length for extended reach Consistent performance through insert compatibility The S783TM is designed around the proven ANHX 1004–1206 indexable insert system, ensuring fast insert changes and predictable cutting geometry. Compatibility with Palbit-type inserts simplifies supply chains and reduces tooling variants on the shop floor. With a 90° cutting angle, the tool supports square-shoulder milling and precise face finishes; this combination yields stable forces and repeatable results in series production. The focus on insert interchangeability translates into lower downtime and a predictable cost-per-part for production planners. Rigidity and reach balanced for everyday milling A 20 mm shank provides the rigidity required for consistent chip evacuation and reduced vibration, while the 160 mm overall length gives sufficient reach for medium-depth pockets. The 30 mm cutting length balances tool engagement and stiffness, helping to maintain dimensional accuracy without sacrificing accessibility. The compact mass (approx. 0.058 kg) makes handling and tool changes straightforward, and the geometry supports stable toolholding in common milling arbors and collets, improving surface quality and tool life. Secure clamping and fast service intervals Insert retention is achieved using the supplied fastener configuration: T8 Torx drive and M3x7 screw for reliable seating under cyclic loads. This familiar fastening standard allows for quick, toolroom-friendly maintenance and reduces the learning curve for operators. The cutter’s three cutting edges distribute load evenly, which moderates wear on each edge and extends the interval between insert indexings. As a result, cycle times remain steady and maintenance planning becomes simple and predictable. Integration into workshop workflows Intended for installation in standard CNC toolholders, the cutter integrates smoothly into existing machining processes without the need for special fixtures. The compact design supports efficient nesting of tools in tool magazines and reduces collision risk in tight setups. For procurement and workshop managers, the combination of insert compatibility, standard fastener types and a robust shank offers a pragmatic route to lower tooling complexity and improved throughput in everyday milling operations. Contact Metav Werkzeuge for tailored advice on integrating the Teknik Makina shank cutter S783TM into production setups — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: S783TM Manufacturer: Teknik Makina Facts Shank diameter: 20 mm Cutting length: 30 mm Overall length: 160 mm Number of cutting edges: 3 Weight: 0.058 kg Cutting angle: 90° Special features For ANHX 1004–1206 indexable inserts Compatible with Palbit insert systems Torx key: T8 Torx screw: M3x7 FAQ Which inserts fit this shank cutter? The cutter is compatible with ANHX 1004–1206 indexable inserts, enabling quick insert swaps and supply-chain alignment with Palbit-style inserts. How is the insert secured on the cutter? Insert retention uses a T8 Torx drive and an M3x7 screw, providing secure seating under milling loads and straightforward maintenance. What advantages do three cutting edges provide? The three cutting edges distribute cutting forces evenly, reducing individual edge wear and helping to maintain consistent surface finish over longer intervals. Can the cutter be used in standard CNC toolholders? Yes; the shank design and dimensions are intended for connection to normal milling arbors and toolholders, facilitating integration into existing tool magazines. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, rigid shank milling solution with a 20 mm shank diameter, a 40 mm cutting length and compatibility with Sandvik R390-11T3 indexable inserts for consistent shoulder and slot milling — order or consult via Metav Werkzeuge for tailored supply and advice. Shank milling cutter S592TM — 20 mm shank, for R390-11T3 indexable inserts (Teknik Makina) The Shank milling cutter S592TM is a solid holder designed to accept R390-11T3 indexable inserts for industrial milling tasks, combining a compact 20 mm shank with a 90° cutting angle for secure axial and radial milling operations. 20 mm shank diameter for rigid clamping Accepts R390-11T3 indexable inserts Three cutting edges for steady material removal Torx M2.5x7 clamping screw with T8 key Exceptional rigidity for repeatable results The holder’s 20 mm shank and 120 mm overall length form a compact interface that reduces deflection during medium-duty milling. The combination of a short, sturdy shank and a 90° cutting angle delivers a predictable cutting force direction, which improves positional accuracy at every pass. For workshops aiming to raise first-pass yield, the mechanical stability of this tool reduces vibration and supports consistent surface finish quality — an economic benefit through fewer reworks and shorter cycle times. Fast insert changes and low downtime Equipped for the common R390-11T3 insert format and supplied with a Torx M2.5x7 clamping screw operated with a T8 key, this holder simplifies insert replacement and clamp torque control. The indexable system means worn cutting edges are replaced rather than whole tools, lowering consumable costs and shortening maintenance intervals. The three-edge seating ensures even load distribution across the insert, which helps to extend indexable insert life and maintain cutting performance between changes. Practical reach and handling for shopfloors With a 40 mm cutting length, a nominal 20 mm diameter and a tool weight of approximately 0.27 kg, this shank tool balances reach with manoeuvrability for fixtures and compact setups. The geometry is suitable for shoulder milling and light slotting where the R390 family is proven. The modest mass aids in quick tool changes and handling on the machine, while the standard interface supports integration into existing tool holders without additional adapters, keeping set-up time and inventory complexity to a minimum. Secure precision machining supplies from Teknik Cutting Tools through Metav Werkzeuge — for detailed compatibility checks or order fulfilment contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: S592TM Manufacturer: Teknik Makina Facts Shank diameter: 20 mm Cutting length (shank): 40 mm Overall length: 120 mm Number of cutting edges: 3 Weight: 0.27 kg Cutting angle: 90° Special features Accepts R390-11T3 indexable inserts Torx clamping screw M2.5x7 Torx key size T8 Compatible with Sandvik insert systems FAQ What insert type fits this holder? The holder accepts R390-11T3 indexable inserts; compatibility has been verified for inserts from Sandvik. Which shank diameter does the tool use? The tool features a 20 mm shank diameter, designed for rigid clamping in standard tool holders. How many cutting edges are provided by the insert seating? The cutter is set up for three cutting edges, enabling steady material removal and balanced loading on the insert. What is the cutting length and overall reach? The assembly provides a 40 mm cutting length with a 120 mm overall length, suitable for medium-reach milling tasks. Which clamping screw and key are required for insert changes? A Torx M2.5x7 clamping screw is specified, to be operated with a T8 Torx key. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust milling solution that combines versatile compatibility with precise dimensions and secure clamp fastening for predictable machining results. Benefit from the 20 mm shank and compatibility with SECO XOMX 1204 indexable inserts for straightforward tool replacement — order via Metav Werkzeuge or consult our specialists for application advice. Teknik Makina Shank Milling Cutter S638TM — for XOMX 0602-1204 Indexable Inserts, 20 mm Shank Teknik Makina Shank Milling Cutter S638TM is a shank-type milling tool designed for indexable-insert turning and milling applications in industrial production. 20 mm shank diameter for stable clamping Compatible with SECO XOMX 1204 indexable inserts Two cutting edges for efficient material removal Torx T10 screw M3.5x8.5 for secure insert fastening Reliable performance from a compact shank design The shank-style cutter delivers a 20 mm shank that provides consistent clamping in standard tool holders, reducing vibration and improving surface finish. Its compact dimensions and 120 mm overall length make the tool suitable for common tool posts and milling arbors where reach and rigidity must be balanced. The tool’s geometry supports stable cutting behaviour, and the two cutting edges offer efficient metal removal while keeping cutting forces predictable. Fast reconditioning and compatibility for reduced downtime Designed for use with XOMX 1204 indexable inserts, the cutter simplifies maintenance: worn cutting edges are replaced quickly without regrinding, which lowers toolroom time and keeps production moving. The insert seat and locking system use a Torx T10 screw (M3.5x8.5) for reliable clamping, ensuring the insert remains secure under machining loads. Compatibility with established SECO insert formats provides access to a wide range of grades and geometries for varied materials. Predictability through clear specifications and industrial fit Measured and documented dimensions support process planning and fixture design: a 20 mm shank diameter, 45 mm cutting length, and 120 mm overall length enable accurate setup and consistent repeatability. The cutter’s 90° cutting angle gives neutral face engagement suitable for facing and slotting operations where perpendicular contact is required. These precise values allow engineers to calculate cutting parameters and choose matching holders with confidence, improving cycle-time estimates and part quality. Built for workshop integration and practical handling At 0.5 kg, the tool is heavy enough to feel robust while remaining easy to handle during tool changes. The solid shank profile and standard fastening method make the cutter straightforward to install in existing setups. Using standardised indexable inserts reduces inventory complexity because the same insert family can be stocked for multiple toolholders. This practical approach supports lean tooling strategies and simplifies spare-part management in the workshop. For application matching or to source the Teknik Makina S638TM with compatible SECO XOMX 1204 inserts, contact Metav Werkzeuge — our consultants provide machining advice and can recommend suitable insert grades for specific component materials. Technical data Article number: S638TM Manufacturer: Teknik Makina Designation: Shank milling cutter for XOMX 0602-1204 indexable inserts Facts Shank diameter: 20 mm Cutting length (shank): 45 mm Overall length: 120 mm Cutting edges: 2 Diameter: 20 mm Weight: 0.5 kg Cutting angle: 90° Special features Compatible with SECO inserts For XOMX 0602-1204 indexable inserts Torx screw: M3.5x8.5 Torx key size: T10 FAQ What insert type does this cutter use? The cutter is designed for XOMX 1204 indexable inserts and is compatible with SECO XOMX 0602–1204 insert formats for straightforward replacement. Which shank and overall dimensions should be expected? The Tekniк Makina S638TM features a 20 mm shank diameter, a 45 mm cutting length, and a 120 mm overall length for predictable setup and clamping. How are the inserts secured in the cutter? Inserts are fixed using a Torx screw (M3.5x8.5) tightened with a T10 Torx key, providing a secure clamp under normal milling loads. How many cutting edges are available and what is their effect? The tool has two cutting edges; this arrangement balances material removal rate and cutting force, supporting efficient machining with manageable power requirements. Is the tool suited for standard toolholders? The shank profile and 20 mm diameter are compatible with commonly used toolholders and arbors, allowing easy integration into existing setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Characteristics: Order Number: HF15TM Item: Shoulder Milling usable with APKT 1003 Indexable Inserts of Korloy Brand: Teknik Makina Quantitative Specifications: Diameter: 20mm Cutting Edges: 6 Weight: 0.481kg Total length: 200mm Cutting Height: 28mm Diameter Connection: 20mm Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Take advantage of the combination of high stability, flexible insert compatibility and precise tool support to keep production running with minimal interruptions; order the Vollbohrer directly via Metav Werkzeuge or consult the technical advisors for application-specific guidance. Vollbohrer U820TM — Indexable insert drill with 20 mm diameter and 60 mm cutting length (Teknik Cutting Tools) The Vollbohrer U820TM is a robust indexable insert drill engineered for precision metalworking, optimised for CNC and turret applications where repeatable hole quality and short cycle times are required. 20 mm diameter for stable drilling 60 mm effective cutting length 25 mm shank for secure clamping Compatible with SPMG 0602 inserts Consistent hole quality through stable geometry and cutting length The design focuses on delivering repeatable results in series production: a nominal 20 mm diameter combined with a 60 mm cutting length and an overall length of 139 mm results in a centred, vibration-resistant cutting action that reduces scrap rates. The combination of a solid tool body and precise insert seating helps maintain hole tolerances across longer runs, while the indexed insert system enables quick replacement without repositioning the tool, supporting uninterrupted machining rhythms. Flexible insert system for reduced downtime and predictable costs This drill accepts SPMG 0602 indexable inserts and is compatible with leading manufacturers Taegutec and YG-1, enabling simple sourcing and predictable spare-part logistics. Using indexable inserts separates cutting-edge wear from the tool body, so cutting edges are renewed in seconds and tool life is extended; the economic benefit is achieved through reduced regrinding and lower inventory burden for full solid drills. For process planners, this means better uptime and a clear cost-per-hole calculation. Secure clamping and balanced handling for reliable machining A 25 mm shank diameter with a 56 mm shank length provides a reliable clamping interface in standard toolholders, ensuring high axial and radial stability during drilling. The tool’s measured weight of 0.347 kg contributes to a balanced spindle load and supports controlled feed rates and surface finishes. The construction was engineered to simplify tool change routines and to maintain concentricity under typical cutting forces, which benefits both roughing and subsequent finishing operations. For tailored advice on integrating this Teknik Cutting Tools indexable insert drill into production, contact Metav Werkzeuge in Emmerich for compatibility checks, supply options and technical consultation via info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical Data SKU: U820TM Name: Vollbohrer Brand: Teknik Cutting Tools Facts Diameter: 20 mm Overall length: 139 mm Cutting length: 60 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.347 kg Special features For indexable inserts SPMG 0602 Compatible with Taegutec and YG-1 inserts Indexable insert drill body Files available (refer to product documentation) FAQ Which inserts fit this drill? The drill accepts SPMG 0602 indexable inserts; compatible manufacturers listed include Taegutec and YG-1 for easy sourcing. Is the tool suitable for CNC spindles and turret heads? Yes, the U820TM indexable insert drill is designed for secure clamping and stable rotation in standard CNC toolholders and turret setups. What are the critical dimensions to check before ordering? Verify the 20 mm diameter, 25 mm shank diameter and the 56 mm shank length against the machine’s holder specifications to ensure correct fit. How does the insert system reduce production costs? By using replaceable SPMG 0602 inserts, cutting edges can be renewed quickly without discarding the drill body, lowering lifecycle costs and minimising downtime. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of stable clamping and extended reach with a 20 mm drilling capacity and 100 mm cutting length, combined with compatibility for Korloy WCm-0402 indexable inserts to reduce tool changes and machining interruptions. Order the U780TM through Metav Werkzeuge or request technical advice from their specialists for integration into production. Indexable drill body U780TM — 20 mm diameter, 100 mm cutting length (Teknik Makina) The Indexable drill body U780TM is designed for production drilling with replaceable indexable inserts, offering long cutting reach for through and deep-hole operations in CNC machining applications. *20 mm diameter for stable core drilling *100 mm cutting length for deeper bores *25 mm shank diameter for secure clamping *Compatible with Korloy WCm-0402 inserts Precision and consistency for repetitive drilling The U780TM is engineered to deliver repeatable bore quality in mid- to high-volume machining. The combination of a 20 mm bore diameter and a 100 mm cutting length allows a single tool body to reach deeper workpieces without secondary extensions, which reduces setup complexity and cumulative run-out. The fixed shank geometry and mass distribution contribute to consistent tool engagement; this translates into predictable cycle times and reduced scrap rates in serial production. Robust clamping and axial stability A 25 mm shank diameter supports solid clamping in standard tool holders and quick-change systems. Greater shank stiffness diminishes vibration and deflection, improving hole roundness and surface finish. This mechanical stability benefits both medium-duty finishing and roughing passes, allowing fewer corrective operations and more efficient use of machining centres. The design focuses on secure retention to keep insert positioning accurate under the axial loads typical of deep drilling. Insert system that limits downtime Compatibility with WCm-0402 indexable inserts from Korloy means cutting edges can be replaced rapidly without reclamping the whole tool body. Indexable inserts reduce regrind cycles and lower tooling cost per hole by shifting the wear to inexpensive, replaceable tips. The modularity of the insert concept supports fast tool changes during shift work and facilitates inventory management of cutting grades tailored to materials and cutting conditions. Manufacturer and application clarity for procurement Supplied by Teknik Makina, the U780TM suits workshop environments that prioritise throughput and predictable maintenance. The tool body’s measured weight of 0.421 kg and standard connection dimensions allow straightforward integration into existing setups. For procurement and planning, the combination of insert availability, measurable geometry and established mounting standards makes the U780TM a practical choice for manufacturers seeking a balance of serviceability and machining reach. For a production-ready drilling solution based on the U780TM, consult Metav Werkzeuge for delivery options or technical matching to existing holders and machining strategies — Metav Werkzeuge’s team in Emmerich can advise on compatibility and supply. Technical data Article number: U780TM Manufacturer: Teknik Makina Designation: Indexable drill body Core data Diameter: 20 mm Overall length: 179 mm Cutting length: 100 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.421 kg Compatibility & features Compatible inserts: WCm-0402 Compatible insert manufacturer: Korloy Files: 62de7ec30aced56449540eb2, 62de7dd80aced56449540e82 FAQ What materials is this tool body suitable for? The U780TM indexable drill body accepts WCm-0402 inserts (Korloy) and is suitable for a wide range of common workshop materials; insert grade selection should be matched to the workpiece material for optimal performance. How does the insert system affect maintenance? Using WCm-0402 indexable inserts on the U780TM reduces maintenance time because worn cutting edges are replaced quickly, avoiding the need to replace or regrind the entire tool body. Which holder or chuck is required for secure mounting? The tool body’s 25 mm shank diameter is compatible with standard tool holders and clamping systems; check the machine’s tooling interface to confirm holder type and clamping method. Is the U780TM suitable for deep-hole drilling applications? Yes; the 100 mm cutting length and 179 mm overall length give extended reach suitable for deeper bores while maintaining stability for serial machining. Where can technical data sheets or CAD files be obtained? Technical documentation associated with the U780TM (file IDs provided) can be requested through Metav Werkzeuge’s sales or technical department for integration and verification. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid Ø20 mm shank combined with a 30 mm effective cutting length for consistent surface quality and reduced vibration; the modular design for APMT 11T3 indexable inserts keeps downtime to a minimum. Order directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. S234TM — Shank milling cutter for APMT 11T3 indexable inserts, Ø20 mm, 30 mm cutting length (Teknik Makina) The S234TM is a shank milling cutter purpose-built to accept APMT 11T3 indexable inserts, providing secure insert clamping and repeatable performance across a wide range of milling tasks Shank Ø20 mm for stable clamping 30 mm effective cutting length Compatible with APMT 11T3 indexable inserts Torx M2.5x5.5 screw, T8 key required High rigidity for predictable cycle times and improved surface finish A robust holder geometry with a Ø20 mm shank and a 30 mm cutting length translates into greater rigidity at the cutting edge, which reduces chatter and delivers a more consistent finish on workpieces. The combination of these dimensions and a substantial overall length of 210 mm stabilises the tool during deep cuts and interrupted cuts alike. With two cutting edges, index changes are infrequent yet fast, so machining cycles stay predictable and tool costs are kept under control. The measured mass of 0.523 kg contributes to good dynamic balance on modern milling spindles, supporting reproducible results in serial production. Fast insert changes and economical tooling strategy The holder is compatible with APMT 11T3 indexable inserts and is listed as suitable for inserts from Korloy, enabling the use of widely available geometries and grades. Insert clamping is secured by a Torx M2.5x5.5 screw; the required key size is T8, allowing quick replacement without special fixtures. Indexable inserts permit multiple cutting edges per insert, so the effective cost per cutting edge is reduced and maintenance becomes a matter of minutes rather than hours. For operations where rapid throughput and low tooling logistics are priorities, this modular approach supports leaner tooling inventories and faster machine turnarounds. Geometry tuned for right‑angle operations and versatile milling A 90° cutting angle gives this shank milling cutter natural aptitude for shoulder milling, slotting and milling of right-angled contours with minimal setup complexity. The tool’s geometry balances the need for aggressiveness and control: suitable for light to medium cuts while maintaining edge stability. The two-edged concept supports alternating cutting directions and can improve chip evacuation compared with single-edge designs. Where tight tolerances and square shoulders are required, this configuration helps deliver repeatable dimensional accuracy with reduced rework. Reliable supply and application support from a precision partner Sourcing tooling through a specialist distributor offers tangible benefits for production planning. Metav combines a broad product range with a local quality filter based in Emmerich, providing stable supply and documented product integrity for industrial buyers. Established relationships with thousands of customers and a catalogue that covers precision metrology and workshop tooling make procurement simpler and reduce the number of suppliers involved in a project. For buyers evaluating process changes or scaling production, availability and consistent performance data are decisive factors in maintaining uptime and cost control. Choose the Teknik Cutting Tools S234TM shank milling cutter for robust right‑angle milling and contact Metav Werkzeuge for tailored application advice and reliable supply from Emmerich: info@metav-werkzeuge.com · +49 2822 7131930 Technical data SKU: S234TM Manufacturer: Teknik Makina Article name: Shank milling cutter for APMT 11T3 indexable inserts ECLASS: 21180806 ETIM: EC011860 Facts Shank diameter: 20 mm Cutting length (shank): 30 mm Diameter: 20 mm Number of cutting edges: 2 Overall length: 210 mm Weight: 0.523 kg Cutting angle: 90° Special features Compatible inserts: APMT 11T3 Suitable insert supplier: Korloy Torx screw: M2.5x5.5 Torx key: T8 FAQ Which inserts fit this holder? The holder accepts APMT 11T3 indexable inserts; Korloy grades are listed as compatible and offer a broad choice of chipbreakers and grades. How is the insert secured in the tool? Insert clamping is via a Torx M2.5x5.5 screw; a T8 key is required for secure and repeatable fastening. What operations is the tool geometry best suited to? The 90° cutting angle and rigid shank make the tool ideal for shoulder milling, slotting and right‑angle work where square corners and consistent surface finish are required. How does the tool support productivity in serial production? A combination of Ø20 mm shank rigidity, 30 mm cutting length and two cutting edges reduces vibration, shortens downtime for index changes and contributes to stable cycle times. Is the tool balanced for high-speed spindles? With an overall length of 210 mm and a mass of 0.523 kg, the holder offers good dynamic behaviour for typical milling setups; balance will depend on the chosen insert and clamping condition. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise insert compatibility, compact overall length and a rigid 25 mm shank for dependable drilling performance; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Indexable drill U314TM — 20 mm diameter, 25 mm shank (Teknik Cutting Tools) The Indexable drill U314TM is an indexable insert drill body engineered for precision holemaking where fast insert changes and consistent geometry are required *Compatible with Taegutec SOMT 0703 inserts *Rigid 25 mm shank for stable clamping *60 mm cutting length for medium-depth holes *Compact overall length of 138 mm for tight setups Precision and predictable hole quality from indexable inserts The modular design delivers predictable geometry by using replaceable inserts, which ensures consistent hole dimensions over repeated cycles. With a 20 mm diameter and a 60 mm cutting length, the tool balances reach and rigidity to maintain bore tolerance. The U314TM’s configuration reduces the frequency of complete tool replacement; only the worn insert is exchanged, which lowers tooling costs and shortens downtime while keeping machining outcomes repeatable. Stable clamping and compact design for production reliability A 25 mm shank and a 138 mm overall length provide a compact yet robust package suited to confined toolholders. The shorter clamping footprint helps to reduce deflection under cutting loads, improving roundness and axial runout stability. For workshops requiring reliable set-up in multi-spindle or constrained fixturing, this design mitigates vibration and supports higher process consistency. Insert compatibility that simplifies logistics and maintenance Designed to accept SOMT 0703 inserts from Taegutec, the drill body streamlines inventory by using an established insert format. The ability to source standard indexable inserts means faster replenishment and predictable wear behaviour; inserts can be rotated or replaced without regrinding solid tools. This results in easier maintenance and cost-effective stocking for production or service environments. Practical dimensions and handling benefits for everyday use Key handling advantages include a clamping length of 56 mm and a low unit weight of 0.347 kg, which together make the tool easy to mount and less demanding on tool changers. The measured dimensions support straightforward tool management and quick changeover routines, contributing to shorter machine idle times and improved throughput without sacrificing stability. Discuss specification matching and delivery options with Metav Werkzeuge — call +49 2822 7131930 or email info@metav-werkzeuge.com for tailored advice and procurement support Technical data Article number: U314TM Manufacturer: Teknik Cutting Tools Brand: Teknik Makina Product type: Indexable drill body Compatible inserts: SOMT 0703 (Taegutec) Core dimensions Diameter: 20 mm Overall length: 138 mm Cutting length: 60 mm Shank diameter: 25 mm Clamping length: 56 mm Weight: 0.347 kg Features & compatibility Indexable insert concept Accepts Taegutec SOMT 0703 inserts Compact length for tight tool setups Rigid 25 mm shank for stable clamping FAQ What insert type does the tool accept? The U314TM accepts SOMT 0703 indexable inserts; Taegutec-compatible inserts are recommended for optimal fit. Is the shank diameter suitable for standard holders? The 25 mm shank is compatible with common 25 mm holders and provides a stable clamp for the indexable drill body. What is the effective cutting length of the drill? The tool offers a cutting length of 60 mm, providing medium-depth drilling capability while maintaining rigidity. Can inserts be rotated to extend service life? Yes, the SOMT 0703 inserts fitted to the U314TM can be indexed or replaced to extend operational life and reduce tooling costs. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of indexable insert compatibility, a 20 mm cutting diameter and a stiff 25 mm shank for reliable, repeatable drilling in production environments; order the Indexable drill body U720TM directly via Metav Werkzeuge or ask our consultants if further technical details are required Indexable drill body U720TM – 20 mm cutting diameter, SPMG 0602 insert compatible (Teknik Makina) The Indexable drill body U720TM is designed for economical, high‑productivity drilling applications where replaceable inserts and rigid clamping matter Compatible with SPMG 0602 inserts 20 mm cutting diameter 80 mm cutting length for deep holes 25 mm shank for secure clamping Reduce tooling cost with indexable inserts and robust design The U720TM tool body combines the advantages of indexable inserts with a compact, rigid construction to lower overall tooling expense. By using replaceable SPMG 0602 inserts the need to regrind is eliminated and tool life is effectively managed; this leads to fewer tool changes and reduced machine downtime. The 20 mm cutting diameter together with an 80 mm cutting length provides a balance between reach and stiffness, while the 25 mm shank ensures secure contact in standard toolholders for consistent performance. Consistent hole quality and machine‑friendly dimensions Designed for shop floors and CNC centres alike, this drill body delivers repeatable hole geometry by combining controlled insert geometry with a stable tool carrier. The overall length of 159 mm gives reach where needed without excessive overhang, supporting accurate concentricity and surface finish. Compatibility with insert manufacturers Taegutec and YG‑1 simplifies procurement and stocking, enabling standardisation of inserts across multiple tool types and helping to maintain uniform hole quality across batches. Streamlined tool management for workshop reliability The U720TM’s modest mass (approx. 0.383 kg) and standardised shank/insert interfaces simplify handling, storage and replacement procedures in busy production settings. Consistent interfaces reduce inventory complexity: one tool body accepts a well‑known insert size, while the readily available insert format keeps downtimes short. Supplied by Teknik Makina and available through Metav Werkzeuge, the tool benefits from a European quality filter and dependable logistics to support uninterrupted operation on the shop floor. For tailored technical advice and reliable supply of the Teknik Makina U720TM indexable drill body, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for prompt, expert support Technical data SKU: U720TM Manufacturer: Teknik Makina Product: Indexable drill body Dimensions & weight Cutting diameter: 20 mm Overall length: 159 mm Cutting length: 80 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.383 kg Compatibility & features Insert type: SPMG 0602 Compatible insert manufacturers: Taegutec, YG‑1 Indexable insert drilling body FAQ Which insert type fits this drill body? The U720TM accepts SPMG 0602 indexable inserts, a common size that simplifies replacement and inventory. What shank size is required for machine mounting? The tool has a 25 mm shank diameter and a 56 mm shank length for secure clamping in standard holders. How deep can this tool cut in a single setup? The effective cutting length is 80 mm, enabling deeper hole work while preserving rigidity for consistent bore quality. Is the U720TM compatible with inserts from major suppliers? Yes, the drill body is compatible with inserts from Taegutec and YG‑1, allowing flexible sourcing options. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from precise holemaking, insert compatibility and robust clamping for stable cycle times; order directly via Metav Werkzeuge or consult our specialists for application advice. Indexable Insert Drill U108TM – Ø 20 mm, 119 mm overall length (Teknik Makina) The Indexable Insert Drill U108TM is an indexable insert drill body engineered for reliable through-hole operations in production and workshop environments, compatible with WCM‑0402 inserts for efficient insert changeover 20 mm cutting diameter for standard holes Compatible with Korloy WCM-0402 inserts 40 mm effective cutting length 25 mm shank diameter for secure clamping Faster, repeatable holemaking through optimised geometry The U108TM drill body offers a combination of a compact design and a clear specification set to keep cycle times predictable. With a Ø 20 mm cutting diameter and a 40 mm cutting length, the tool supports repeated holemaking with consistent results, reducing scrap and rework. The 119 mm overall length balances reach and rigidity, helping to maintain concentricity and minimise runout when mounted in appropriate holders. Explaining the benefit: a defined effective cutting length means bosses and fixtures can be designed around a known cutting zone, simplifying process planning and reducing set-up variations for series production. Economical tooling through insert compatibility and quick serviceability Compatibility with WCM-0402 insert geometry allows rapid edge changes without replacing the whole tool body, converting maintenance time into productive machining minutes. Using standardised indexable inserts from trusted suppliers such as Korloy reduces per‑hole tooling costs and simplifies stock management for workshop stores. The modular approach also enables the selection of grades and coatings to suit specific workpiece materials, offering a pragmatic cost-benefit: lower running costs per hole and shorter downtime for insert replacement compared with solid carbide alternatives. Secure clamping and machine-friendly interface for stable machining A 25 mm shank provides a solid interface for chucks and collet systems, improving stability under load and helping to avoid chatter. The robust shank dimension supports secure clamping and a consistent connection to the spindle, which contributes to reduced vibration and extended insert life. For machine operators, this translates into fewer corrective interventions and a steadier process window, particularly important when running medium-length production cycles where tool stability directly affects surface finish and positional tolerance. Practical applications and shop-floor benefits Designed as a general-purpose indexable drilling solution, the tool body is suited to workshops that prioritise serviceability and predictable output. The construction supports repeated insert changes and simplifies inventory: keep a small selection of WCM-0402 inserts and one tool body per diameter to cover many jobs. The relatively low mass of the assembly aids acceleration and deceleration on CNC machines, making the system suitable for both single‑station machining centres and multi‑spindle production cells where tooling change speed and reliability are critical. Discuss specific requirements with Metav Werkzeuge — request a tailored specification or a quotation for the Teknik Makina U108TM indexable insert drill by contacting Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: U108TM Manufacturer: Teknik Makina Product designation: Indexable insert drill (translated from Vollbohrer) Facts Diameter: 20 mm Overall length: 119 mm Cutting length: 40 mm Shank (aufnahme) diameter: 25 mm Weight: 0.327 kg Special features Compatible insert type: WCM-0402 Recommended insert supplier: Korloy Indexable insert drilling principle Robust shank for secure clamping FAQ What insert type fits this drilling body? The drilling body accepts WCM-0402 indexable inserts; Korloy inserts with this designation are compatible with the U108TM. Which shank size is required for correct clamping? A 25 mm shank diameter is specified for the U108TM to ensure secure clamping and machine compatibility. What is the effective cutting length of the tool? The tool provides a 40 mm cutting length, enabling controlled hole depth and repeatable machining. Is the tool suitable for long-reach drilling applications? With a 119 mm overall length, the tool offers modest reach while maintaining rigidity; it is optimised for standard through-hole and medium-reach operations rather than extreme long-reach scenarios. How does indexable insert tooling reduce running costs? By replacing only the worn inserts (WCM-0402) rather than the entire body, the system lowers per-hole tooling expense and shortens maintenance downtime. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Optimise machining cycles with a robust 20 mm shank and five cutting edges for consistent chip control; the M2x4.2 Torx fixing with T6 key enables fast insert changes and secure clamping. Order the shank cutter directly via Metav Werkzeuge or contact our consultants for specification support. S006TM Shank Cutter by Teknik Makina — for APMT 0602 indexable inserts, 20 mm shank S006TM Shank Cutter designed for secure clamping and quick insert replacement in medium-duty milling applications For APMT 0602 indexable inserts 20 mm shank diameter for robust clamping Five cutting edges for smooth engagement Quick replacement with M2x4.2 Torx screw Faster cycle times through indexable-insert efficiency The use of APMT 0602 indexable inserts delivers a cost-efficient route to high material removal without the need for full regrinding or reconditioning. With a 20 mm shank, the tool offers enhanced rigidity at the spindle, which reduces chatter and supports higher feed rates where appropriate. The combination of insert indexing and the cutter’s geometry leads to predictable tool life and lower tooling cost per component, making it a pragmatic choice for batch production and mixed-series work. Secure set-up and rapid maintenance for production continuity Tool changeovers are simplified by the M2x4.2 Torx screw and compatible T6 key, allowing technicians to replace inserts swiftly and safely. The cutter’s five cutting edges distribute the cutting load evenly across the circumference, improving engagement stability and offering a more uniform surface finish on the workpiece. These features reduce downtime and make the tool suitable for workshops that require repeatable set-ups and fast recovery between jobs. Built to integrate with existing tool systems and inventory With a measured 110 mm overall length and a 30 mm cutting length, the shank cutter balances reach and stiffness for common milling tasks. Compatibility with Korloy indexable inserts means simple inventory management for customers already sourcing that brand, while the standardised fixing method aligns with common workshop procedures. The tool’s practical dimensions and standardised insert format support straightforward tool holder selection and inventory rationalisation. Contact Metav Werkzeuge for tailored advice on toolholders, delivery times and inventory support—call +49 2822 7131930 or email info@metav-werkzeuge.com and benefit from direct supply from Emmerich Technical data SKU: S006TM Manufacturer: Teknik Makina Shank diameter: 20 mm Cutting length: 30 mm Overall length: 110 mm Diameter: 20 mm Number of cutting edges: 5 Weight: 0.24 kg For APMT 0602 indexable inserts Compatible insert manufacturer: Korloy Torx screw: M2x4.2 Torx key: T6 Cutting angle: 90° FAQ Which inserts fit this shank cutter? The shank cutter accepts APMT 0602 indexable inserts; compatibility with Korloy inserts is stated for straightforward sourcing and stocking. How is the insert secured and which tool is required? Inserts are fixed with an M2x4.2 Torx screw; a T6 key is used for tightening and replacement to ensure reliable clamping. What are the key dimensions to check for toolholder selection? Check the 20 mm shank diameter, 110 mm overall length and 30 mm cutting length to ensure correct toolholder and reach for the application. Is this cutter suitable for high-volume production? The combination of a rigid 20 mm shank and indexable inserts makes the cutter suitable for repetitive production where predictable tool life and rapid insert changes are priorities. What is the product SKU for ordering or reordering? Order using SKU S006TM to ensure the correct Teknik Makina shank cutter is supplied. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Achieve repeatable, cost-efficient milling through the combination of a rigid 20 mm shank and compatibility with RDMW 0702 indexable inserts; the secure Torx clamping enables rapid insert changes and reduced downtime. Order the shaft milling cutter directly via Metav Werkzeuge or ask the consultants for application-specific advice. Shaft milling cutter R142TM — indexable insert holder with 20 mm shank (Teknik Makina) The Shaft milling cutter R142TM is a robust indexable-insert milling tool intended for medium-duty milling operations that use RDMW 0702 inserts, offering a balance of stability and accessibility for workshop and production environments. Indexable inserts RDMW 0702 compatible 20 mm shank for stable toolholding 45 mm effective cutting length Secure Torx clamping M2.5x5.5, T8 key Stable clamping and reduced vibration for consistent results With a 20 mm shank and an overall length of 120 mm, this shank cutter provides enhanced rigidity that translates into consistent surface finish and longer insert life. The three-flute configuration delivers a stable cutting action that lowers chatter and helps maintain tolerances over longer runs. In practical terms, that means fewer rejects and less rework in serial production, while the modest tool weight of 0.278 kg makes handling and changeover straightforward on most milling spindles. Quick insert exchange and broad tool compatibility for flexible machining Designed for RDMW 0702 indexable inserts and compatible with Taegutec inserts, the toolholder uses a Torx clamping system (M2.5x5.5 screw, T8 key) to allow fast and secure insert changes. Indexable inserts mean lower per-cutting-edge cost and faster on-site replacement compared with solid-carbide tools. The 45 mm cutting length provides room for a variety of part geometries while keeping the tool projection short enough to preserve stiffness — a clear benefit when switching between roughing and semi-finishing operations. Practical benefits for workshop efficiency and maintenance The R142TM reduces setup complexity: standard Torx tooling simplifies insert retention checks and maintenance intervals, while the compact design minimises tool overhang. The three cutting edges help distribute cutting forces evenly, which can extend the lifespan of both the inserts and the holder. For procurement and inventory planning, the use of common RDMW 0702 inserts and a standard 20 mm shank supports parts consolidation, reducing the number of different tools required in the cabinet and speeding up changeovers on the shop floor. Contact Metav Werkzeuge today to discuss integrating Teknik Cutting Tools' R142TM into production or to request tailored recommendations from the Metav Werkzeuge team in Emmerich Technical data SKU: R142TM Product name: Shaft milling cutter for RDMW 0702 indexable inserts Manufacturer: Teknik Makina Facts Shank diameter: 20 mm Cutting length: 45 mm Overall length: 120 mm Diameter: 20 mm Number of cutting edges: 3 Weight: 0.278 kg Special features Compatible inserts: RDMW 0702 Suitable insert manufacturer: Taegutec Clamping screw: M2.5x5.5 (Torx) Torx key size: T8 FAQ Which inserts fit this toolholder? The shaft milling cutter R142TM accepts RDMW 0702 indexable inserts and is specified for inserts from manufacturers such as Taegutec, ensuring wide availability and interchangeability. How is the insert secured and exchanged? Inserts are clamped with a Torx screw M2.5x5.5; exchange and torqueing are performed using a T8 Torx key to achieve secure and repeatable clamping. What are the key dimensions affecting machine setup? Key dimensions are the 20 mm shank diameter, 45 mm effective cutting length, and 120 mm overall length, which together determine required spindle holder and allowable tool projection. How many cutting edges does the tool provide and why that matters The tool features three cutting edges, which balance chip removal and cutting forces to reduce chatter and improve tool life in many milling operations. Is this holder suitable for long-reach applications? With an overall length of 120 mm and a 20 mm shank, the cutter is intended for moderate reach; longer overhangs will reduce stiffness and should be avoided for high-precision tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of secure clamping, integrated internal coolant and straightforward insert compatibility for efficient milling operations; order directly via Metav Werkzeuge or request tailored advice from our consultants. Shank milling cutter for VDKT 11T2 indexable inserts — Teknik Makina, 20 mm shank, internal coolant Shank milling cutter for VDKT 11T2 indexable inserts with internal coolant, designed to accept Korloy inserts and to integrate seamlessly into workshop tooling systems. 20 mm shank for stable clamping Internal coolant for improved insert life Compatible with VDKT 11T2 Korloy inserts 100 mm overall length, 30 mm cutting length Precision and compatibility that reduce setup time This Shank milling cutter is engineered to accept VDKT 11T2 indexable inserts, a common geometry that simplifies stocking and reduces machine downtime. The combination of a 20 mm shank and a compact overall length ensures stable clamping in standard holders, which translates into consistent machining results. Indexable inserts allow cost-effective replacement of the cutting edge without regrinding the body, so toolholding changeovers are fast and repeatable — a clear productivity advantage for batch and continuous production runs. Improved thermal control for longer tool life Integrated internal coolant supplies cutting fluid directly to the insert seat, which improves cooling and helps evacuate chips from the cutting zone. By reducing thermal stress on the insert and insert seat, the cooling channel contributes to steadier cutting conditions and more predictable toolwear. For operations where process stability and repeatability matter, this internal supply is a decisive factor in maintaining surface finish and dimensional accuracy over longer cycle times. Practical design for efficient maintenance and handling With a 30 mm cutting length and two cutting edges, the tool delivers balanced engagement with predictable chip formation. Insert retention is secured with M2.5x5.5 torx screws, tightened using a T8 key for quick and reliable insert changes. The accessible screw design and standardised insert form make routine maintenance straightforward, keeping downtime to a minimum and simplifying staff training in the workshop. Suitable integration into production workflows As a modular milling solution, the cutter fits into existing tool inventories where VDKT 11T2 inserts are already used, enabling flexible process planning. It is suitable for machining tasks where insert change speed, coolant delivery and secure toolholding are priorities. The robust specification supports use in general-purpose milling fixtures and can be incorporated into both manual and CNC setups without costly adapter requirements. For enquiries about Teknik Makina's S399TM shank milling cutter and supply from Metav Werkzeuge, please contact Metav Werkzeuge in Emmerich for delivery and technical consultation at info@metav-werkzeuge.com or +49 2822 7131930 — our specialists will advise on fixture compatibility and lead times. Technical data Article number: S399TM Product type: Shank milling cutter Manufacturer: Teknik Makina Facts Shank diameter: 20 mm Overall length: 100 mm Cutting length: 30 mm Number of cutting edges: 2 Weight: 0.314 kg Torx screw: M2.5x5.5 Torx key: T8 Special features Internal coolant Compatible inserts: VDKT 11T2 Compatible insert manufacturer: Korloy SKU: S399TM FAQ What type of inserts does this cutter accept? The cutter accepts VDKT 11T2 indexable inserts; it is supplied to work with Korloy inserts in that geometry. Is internal coolant available on this tool? Yes, the tool is equipped with internal coolant, which delivers coolant directly to the insert seat to aid cooling and chip evacuation. What are the shank and overall lengths of the milling cutter? The milling cutter features a 20 mm shank and a 100 mm overall length, with a 30 mm cutting length. Which screw and key are required for insert changes? Insert retention uses an M2.5x5.5 torx screw that is tightened with a T8 key; the design allows fast and secure insert replacement. Who manufactures this shank milling cutter and what is the SKU? The tool is manufactured by Teknik Makina and sold under SKU S399TM, designed for VDKT 11T2 inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of proven compatibility and a compact, rigid design to shorten set‑up times and maintain consistent machining quality; the combination of a secure Torx fixing and standard WNGX 0403 insert interface supports efficient tool changes and reliable repeatability — order directly via Metav Werkzeuge or consult our specialists for any application questions. Shank cutter S944TM — Indexable cutter for WNGX 0403 inserts, Ø20 mm (Teknik Makina) A shank cutter S944TM designed for secure mounting of WNGX 0403 indexable inserts, intended for general indexable‑insert milling tasks in production and job‑shop environments. Ø20 mm shank diameter For WNGX 0403 indexable inserts Torx screw M2.5×5.5, key T8 110 mm overall length, 3 cutting edges Faster set‑ups thanks to standard insert compatibility The combination of a standard interface for WNGX 0403 indexable inserts and a proven clamp system reduces inventory complexity and shortens downtime between jobs. Because the tool accepts widely used Korloy inserts, procurement and replacement are simplified, which in turn improves tool availability on the shop floor. The secure Torx fixing (M2.5×5.5) operated with a T8 key ensures clamping repeatability and straightforward insert changes without complex fixtures, contributing to leaner tool management. Compact dimensions that support rigidity and surface consistency A Ø20 mm shank and a total length of 110 mm balance reach and stiffness to maintain stable cutting conditions. The tool’s three cutting edges distribute cutting forces across multiple contact points, reducing vibration and promoting consistent surface finish. For milling operations where stability affects part quality, this compact configuration helps keep tolerances tight while allowing practical tool overhang for common set‑ups. Simple maintenance and secure fixing for productive workshops The carriage and screw arrangement is configured for quick insert replacement and secure retention under load. The specified Torx screw size and key type standardise maintenance routines and lower the risk of incorrect fastenings. Compatible with Korloy WNGX 0403 inserts, the cutter is suitable for shops that prioritise predictable tool change cycles and a minimal learning curve for operators, supporting uninterrupted production rhythm. Contact Metav Werkzeuge today to discuss the Teknik Cutting Tools S944TM shank cutter, confirm its fit for specific machining tasks and arrange delivery from Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: S944TM Manufacturer: Teknik Makina Article designation: Shank cutter for WNGX 0403 Indexable Inserts Diameter: 20 mm Overall length: 110 mm Cutting edges: 3 Shank diameter (clamp): 20 mm Torx screw: M2.5×5.5 Torx key: T8 Compatible inserts: Korloy WNGX 0403 eClass: 21180806 ETIM: EC011860 Numbers / Core technical data Diameter: 20 mm Overall length: 110 mm Cutting edges: 3 Shank diameter: 20 mm Torx screw dimension: M2.5×5.5 Torx key size: T8 Designs / Special features Compatible with Korloy WNGX 0403 inserts Torx screw M2.5×5.5 with T8 key Indexable insert system Manufacturer: Teknik Makina SKU: S944TM FAQ Are Korloy WNGX 0403 inserts compatible with this tool? Yes. The shank cutter S944TM is designed for WNGX 0403 indexable inserts and accepts Korloy‑specification plates. What are the shank and overall dimensions? The tool has a Ø20 mm shank and an overall length of 110 mm, providing a compact but usable overhang. How many cutting edges does it have and why does that matter? It has three cutting edges; this layout spreads the cutting load, reduces vibration and helps maintain a consistent surface quality. What Torx screw and key are required for insert clamping? Clamping uses a Torx screw sized M2.5×5.5 and requires a T8 key for tightening and removal. Is this cutter suitable for production use in job shops? Yes. The standard insert interface, secure Torx fixing and compact geometry make it appropriate for routine indexable‑insert milling operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a 20 mm shank, a 55 mm cutting length and 3 cutting edges for stable, productive milling operations; order the tool directly via Metav Werkzeuge or ask consultants if guidance on insert selection is required. Shank Milling Cutter S628TM – 20 mm diameter, 3 cutting edges (Teknik Makina) The Shank Milling Cutter S628TM is a robust indexable milling tool designed for use with XOMX 0602–1204 indexable inserts, offering compact geometry for shoulder milling and slotting in standard machining setups 20 mm shank diameter 55 mm cutting length 3 cutting edges Compatible with SECO XOMX indexable inserts Stable machining for consistent throughput The compact 20 mm shank and optimised geometry provide a high degree of rigidity, which reduces vibration and improves tool life. With a 55 mm cutting length and 3 cutting edges, the cutter delivers an efficient material removal rate while maintaining surface quality; the combination of these dimensions allows shorter cycle times and steadier feeds. Decision-makers benefit from predictable performance in series production, where reduced tool variation translates directly into fewer reworks and steadier output. Fast, secure insert changes to minimise downtime Insert retention is handled via a precise fastener system: a M2.5 Torx screw fixed with a T8 key ensures repeatable clamping force and straightforward indexable insert swaps. The use of standardised attachment components simplifies workshop logistics and reduces maintenance time between operations. The indexable concept also lowers long-term running costs, as worn cutting edges can be rotated or replaced without discarding the entire tool body. Compact dimensions suited to versatile set-ups With a 150 mm overall length and a nominal mass of 0.373 kg, the cutter balances accessibility and stability for a wide range of milling stations. The tool’s 90° cutting angle supports true shoulder faces and square corners without extensive secondary finishing. Such proportions make the cutter suitable for machines with limited overhang while providing enough reach for common fixture layouts; handling is comfortable during set-up and the relatively low weight minimises spindle load during rapid repositioning. Reliable supply and technical backing for production use Sourcing the tool through Metav brings an established supply chain and workshop expertise to the procurement decision. Metav’s distribution model functions as a quality filter for the European market, backed by long-term relationships with customers and a comprehensive product range. This combination supports planned stock rotation and consistent replenishment, helping production planners secure the right tooling at the right time while maintaining traceability across orders. Choose the Teknik Cutting Tools S628TM for reliable indexable milling performance and contact Metav Werkzeuge for procurement and technical advice from Emmerich; email info@metav-werkzeuge.com or call +49 2822 7131930 for further specification support Technical data Article number: S628TM Manufacturer: Teknik Makina Product name: Schaftfräser for XOMX 0602-1204 Indexable Inserts ECLASS: 21180806 ETIM: EC011860 Facts Diameter: 20 mm Shank diameter: 20 mm Cutting length: 55 mm Overall length: 150 mm Cutting edges: 3 Weight: 0.373 kg Cutting angle: 90° Special features Compatible inserts: XOMX 0602–1204 (also XOMX 0903) Compatible with SECO inserts Torx screw: M2.5x5.5 Torx key: T8 FAQ Which indexable inserts are compatible with this cutter? The S628TM is specified for XOMX 0602–1204 indexable inserts and is noted as compatible with XOMX 0903 variants; adapters or specific seat forms from SECO may be required for certain grades. How are inserts secured in the cutter? Insert clamping is achieved with a M2.5 Torx screw tightened using a T8 key, providing repeatable clamping force for safe machining and rapid changeovers. What machining tasks suit this cutter best? The tool’s 90° cutting angle and compact geometry make it well suited to shoulder milling and slotting where square faces and accurate edges are required. Does the cutter require special spindle interfaces? The shank form is designed for conventional collet or holder systems that accept a 20 mm shank; the 150 mm overall length and modest mass support standard workshop set-ups. How does the cutter aid production efficiency? The combination of a rigid 20 mm shank, a 55 mm cutting length and three cutting edges reduces vibration and allows stable feeds, which helps maintain surface finish and extend insert life Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a stable clamping interface and proven indexable-insert compatibility: the cutter combines a 20 mm shank with ADMX 0702 insert support and four cutting edges for dependable production throughput. Order the shank milling cutter directly via Metav Werkzeuge or consult our specialists for application advice. Shank milling cutter S760TM — 20 mm shank, for ADMX 0702 indexable inserts (Teknik Makina) The Shank milling cutter S760TM is a robust 4-flute tool engineered for face and shoulder milling with ADMX 0702 indexable inserts in general machining applications High-stability 20 mm shank Compatible with ADMX 0702 inserts Four cutting edges for balanced cutting 125 mm overall length for extended reach Precision and stability for repeatable machining The tool offers a 20 mm shank and a balanced four-flute geometry that reduces vibration and improves surface finish during both roughing and light finishing passes. The combination of a solid shank diameter and a nominal 125 mm overall length provides stable clamping and repeatable tool life, which translates directly into fewer tool changes and more consistent part tolerances. For shops working to tight process windows, the cutter’s 90° cutting angle supports square shoulder operations with predictable cutting forces. Designed for productivity and simple maintenance With a dedicated insert pocket for ADMX 0702 indexable inserts and a secure M2x4.2 Torx screw (Torx key T6) the system simplifies insert changes and reduces downtime. The modular insert design allows rapid replacement without regrinding, and the cutter’s 17 mm effective cutting length delivers material engagement suitable for common face and slotting tasks. The modest weight of 0.293 kg keeps spindle load low while maintaining rigidity, making the cutter suited for both manual tool setups and CNC environments where cycle time and tool-change efficiency matter. Compatibility, application and tool-room guidance Manufactured for compatibility with Pramet-style tooling, the S760TM supports indexable insert use across a range of ferrous and non-ferrous operations when paired with the appropriate insert grade. The adapter-style pocket accepts ADMX 0702 plates, enabling the selection of carbide grades and coatings tailored to stainless steels, alloy steels or general engineering materials. For predictable results, match insert geometry and grade to the specific machining task; the cutter’s four cutting edges deliver a balanced cut pattern that helps maintain tool life and workpiece quality. For technical fit confirmation or to specify the S760TM for a particular application, contact Metav Werkzeuge by phone at +49 2822 7131930 or by email at info@metav-werkzeuge.com — our advisors can confirm suitability and offer ordering support Technical data Article number: S760TM Manufacturer: Teknik Makina Article name: Shank milling cutter for ADMX 0702 indexable inserts Compatible insert type: ADMX 0702 Core dimensions Shank diameter: 20 mm Cutting length (effective): 17 mm Cutting diameter: 20 mm Number of cutting edges: 4 Overall length: 125 mm Weight: 0.293 kg Cutting angle: 90° Designs / Special features Torx screw: M2x4,2 Torx key: T6 Compatible with Pramet inserts 4-flute geometry for balanced cutting FAQ Which indexable inserts fit the cutter? The S760TM shank milling cutter from Teknik Makina is designed for ADMX 0702 indexable inserts and is compatible with Pramet-manufactured plates of that designation. Is the shank size suitable for standard toolholders? Yes, the S760TM features a 20 mm shank that fits holders and collets specified for 20 mm tooling, providing secure clamping for stable machining. What fastening hardware is required for insert changes? Insert clamping uses an M2x4.2 Torx screw secured with a T6 Torx key; the S760TM design facilitates rapid and repeatable insert replacement. For which operations is this cutter best suited? The S760TM is intended for face and shoulder milling where a 90° cutting angle and four cutting edges provide efficient material removal and a good surface finish. How heavy is the tool and does weight affect spindle load? The S760TM weighs 0.293 kg, which is light enough to keep spindle load low while maintaining the rigidity needed for industrial machining cycles. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of reliable indexable-insert performance, a compact 25 mm shank and a 40 mm cutting length for efficient, repeatable holemaking; order the U920TM indexable insert drill directly via Metav Werkzeuge or ask our consultants if needed. U920TM indexable insert drill – Ø20 mm, 25 mm shank (Teknik Makina) U920TM is an indexable insert drill intended for stable, cost-effective production drilling in general engineering and CNC machining applications. *Indexable insert drill for SPMG 0602 *Cutting diameter Ø20 mm *25 mm shank with 56 mm clamping length *40 mm cutting length for deeper holes High-efficiency holemaking with indexable inserts The design focuses on productive drilling cycles by combining an indexable insert concept with a substantial 40 mm cutting length, enabling longer uninterrupted drilling operations compared with short-tip solutions. Using SPMG 0602 inserts reduces per-hole tooling cost because inserts are replaceable, and wear is limited to the insert rather than the whole tool body. The result is a measurable improvement in throughput and a predictable maintenance rhythm for the workshop. Stable clamping and consistent set-up reduce downtime A robust 25 mm shank and a 56 mm engagement length deliver secure seating in toolholders, minimising runout and vibration during machining. The tool’s compact 119 mm overall length and modest weight (0.334 kg) support rapid spindle acceleration and simpler balancing on CNC machines. Compatibility with established insert vendors such as Taegutec and YG-1 streamlines procurement and ensures swift re‑tooling when inserts require replacement. Versatile integration for production environments The modular nature of the drill body allows it to be used where indexable systems are preferred for repeatability and cost control. The combination of Ø20 mm bore capability and a standard insert type makes the tool well suited to serial drilling in components where predictable tool life and quick insert changes are priorities. Built by Teknik Makina, the design aims to offer reliable performance across multiple shifts while keeping spare-part logistics straightforward for maintenance teams. Contact Metav Werkzeuge for product availability, technical specification sheets and delivery options for the Teknik Makina U920TM indexable insert drill — info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: U920TM Manufacturer: Teknik Makina Designation: Vollbohrer ECLASS: 21180201 Facts Diameter: 20 mm Overall length: 119 mm Cutting length: 40 mm Shank diameter: 25 mm Shank clamping length: 56 mm Weight: 0.334 kg Special features Compatible with SPMG 0602 indexable inserts Compatible insert manufacturers: Taegutec, YG-1 Intended for indexable insert drilling systems FAQ What insert type does this drill use? The U920TM drill accepts SPMG 0602 indexable inserts and is compatible with inserts from manufacturers such as Taegutec and YG-1. What are the main dimensions to consider for toolholder selection? Key dimensions are Ø20 mm cutting diameter, 25 mm shank diameter, 56 mm clamping length and 119 mm overall length. Is the tool suitable for serial production on CNC lathes or milling centres? Yes, the indexable insert concept of this drill is specifically intended to support serial production on CNC machining centres where fast insert changes and repeatability are required. How does the insert system affect running costs? Using replaceable SPMG 0602 inserts reduces running costs because only the insert needs replacement when worn, preserving the drill body and lowering per-hole expenditure. Can inserts from other manufacturers be used? Inserts from established suppliers such as Taegutec and YG-1 are listed as compatible, offering flexibility in sourcing. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Compact indexable drill body with Ø20 mm cutting diameter, 25 mm shank and 45 mm cutting length for deeper holes; precise insert fit for Korloy QC--10T304. Reduced tool changes and predictable repeatability support efficient batch production. Order the insert drill body directly via Metav Werkzeuge or ask our consultants if needed. Indexable insert drill body U040TM by Teknik Cutting Tools — Ø20 mm, 25 mm shank U040TM is an indexable insert drill body designed for production drilling where secure clamping and fast insert replacement matter, especially in CNC machining and toolroom applications. Ø20 mm cutting diameter 25 mm shank diameter for secure clamping Compatible with Korloy QC--10T304 inserts 45 mm cutting length for deep holes Precision and productivity for repetitive holemaking The U040TM functions as a robust indexable drill body that combines a compact profile with dependable repeatability. With a 25 mm shank and a Ø20 mm cutting diameter, the tool is engineered to fit standard toolholders and maintain concentricity under load. The replaceable insert system reduces downtime: when a cutting edge wears, only the Korloy QC--10T304 insert needs replacement, keeping maintenance straightforward and costs predictable. For production environments, this means fewer set-ups and consistent hole quality across batches. Designed for secure clamping and longer engagement A 56 mm clamping length and a total length of 116 mm provide stability for deeper operations while the 45 mm cutting length permits extended engagement without resorting to excessively long tools that increase deflection. The compact mass of 0.33 kg supports high-speed indexable drilling with lower spindle load and improved surface finish. Where positional accuracy and repeatable hole diameter are crucial, the assembly reduces vibrations and contributes to shorter cycle times — a clear rational advantage for production-focused workshops. Compatibility, versatility and simple replacement strategy Engineered for compatibility with Korloy inserts, the drill body accepts the proven QC--10T304 insert family, enabling quick index changes and flexible cutting-edge selection based on workpiece material. The tool is suited to standard machining centres and toolholders that accept a 25 mm shank diameter. For procurement and planning, this means simplified spare inventory: the body remains reusable while inserts are stocked as consumables, improving total cost of ownership and operational readiness. Contact Metav Werkzeuge for a machining consultation and secure the Teknik Cutting Tools U040TM insert drill body; Metav Werkzeuge can confirm fitment and application suitability at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: U040TM Manufacturer: Teknik Makina Article type: Insert drill body Compatible inserts: QC--10T304 (Korloy) Shank diameter: 25 mm Cutting diameter: 20 mm Cutting length: 45 mm Clamping length: 56 mm Overall length: 116 mm Weight: 0.33 kg FAQ What insert type does this drill body use? The drill body accepts Korloy QC--10T304 indexable inserts; this ensures fast replacement and a consistent cutting geometry. Which shank size is required for mounting? The tool requires a 25 mm shank receptacle; ensure the machine holder matches this diameter for secure clamping. Is the tool suitable for deep holes? With a 45 mm cutting length and a 116 mm overall length, the body is suited to moderately deep holes where rigidity is required. Can the same body be re-used after insert wear? Yes — the body is designed for repeated use while worn inserts are replaced, reducing the need for full-tool replacement. Which manufacturer produces this drill body? The U040TM insert drill body is supplied by Teknik Makina and intended for use with Korloy inserts when matching holders are employed. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, insert-compatible drilling solution that combines reach and stability: a 20 mm cutting diameter with a 25 mm shank provides secure clamping and repeatable holemaking, while compatibility with Korloy WCM-0402 inserts reduces tooling inventory. Order the U150TM indexable drill directly via Metav Werkzeuge or ask our consultants if needed. U150TM indexable drill — 20 mm diameter, 25 mm shank (Teknik Makina) The U150TM indexable drill is a robust drill body designed for insert-based holemaking, offering stable clamping and extended reach for deep-hole operations 20 mm diameter for standard hole sizes Compatible with Korloy WCM-0402 inserts 25 mm shank for stable clamping 60 mm cutting length for deeper holes Engineered for efficient, repeatable drilling with insert technology The U150TM is built as an indexable insert drill body, delivering a rational improvement to cycle times through reduced regrind and quick insert changes. With a 20 mm nominal diameter and an insert specification of WCM-0402, the tool converts insert life and edge geometry into consistent hole quality. The use of indexable inserts allows the cutting edge to be replaced in seconds, which reduces machine downtime and simplifies tool management in volume production. The design emphasises axial stiffness and reliable chip evacuation so that productive cutting parameters can be exploited without sacrificing process stability. Precision clamping and extended cutting length for varied applications A 25 mm shank provides a secure interface for conventional chucks and holders, improving runout control and repeatability on lathes and machining centres. The 60 mm cutting length together with a 139 mm overall length gives access to deeper bore features while maintaining sufficient overhang control; the shorter 56 mm mounting length is optimised to balance reach and rigidity. These dimensions support operations where both access and form tolerance matter, such as stepped bores and through-holes in medium-duty workpieces. The result is measurable process reliability and reduced scrap rates through improved concentricity and surface finish. Compatibility, workshop efficiency and trust in supply Compatibility with Korloy inserts (WCM-0402) reduces tooling complexity for workshops that already standardise on that insert family. The drill body’s lightweight construction (approx. 0.344 kg) eases handling during set-up and is compatible with automated tool changers where compact mass helps maintain balance. By focusing on transferable insert systems and straightforward clamping geometry, this drilling solution supports lean inventory strategies and faster set-ups — benefits that directly contribute to lower unit costs and steadier throughput on production lines. For procurement or a technical evaluation of fitment with existing holders and inserts, contact Metav Werkzeuge to discuss the U150TM indexable drill and available supply options Technical data SKU: U150TM Product type: Indexable drill body Brand: Teknik Makina Compatible insert: WCM-0402 Compatible insert manufacturer: Korloy Core measurements Diameter: 20 mm Shank diameter: 25 mm Cutting length: 60 mm Mounting length: 56 mm Overall length: 139 mm Weight: 0.344 kg Features & compatibility Insert-based cutting system Designed for secure clamping and reduced runout Suited to through-hole and recessed drilling tasks Lightweight construction for easy handling Matches Korloy WCM-0402 insert geometry FAQ What insert type does this drill use? The drill accepts WCM-0402 indexable inserts; the body is manufactured to interface precisely with that insert geometry. Is the shank suitable for standard tool holders? The 25 mm shank is compatible with common clamping systems and offers stable mounting for accurate holemaking. What maximum reach does the tool provide? With a 60 mm cutting length and 139 mm overall length, the body is intended for medium-depth drilling where access beyond the face is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of robust drill geometry, reliable insert compatibility and a compact 25 mm shank for secure clamping — ideal for steady production runs; order directly via Metav Werkzeuge or consult our specialists if clarification is needed. U608TM Solid drill — 20 mm diameter, 159 mm overall length (Teknik Cutting Tools) The U608TM Solid drill is a precision cutting tool for indexable-insert drilling, designed for shop-floor and CNC applications where repeatability and fast insert changes are required 20 mm cutting diameter 159 mm overall length Compatible with Korloy WCM-0402 inserts 25 mm shank for rigid clamping Greater rigidity for consistent hole quality The drill body is engineered to provide high rigidity through a 25 mm shank and compact proportions. With a 20 mm cutting diameter and 159 mm overall length, the tool minimises deflection under load, which helps to maintain concentricity and hole tolerance across a production batch. The 80 mm cutting length offers an effective balance between reach and stiffness, reducing chatter and the need for rework — a direct efficiency gain for repetitive drilling operations. Fast insert changes to reduce downtime Compatibility with Korloy indexable inserts (type WCM-0402) allows quick replacement of the cutting edge without full regrinding of the body. Indexable inserts mean predictable wear cycles and straightforward tool maintenance: once an insert edge dulls, replacing the small insert restores cutting performance within minutes. This approach supports a better cost-per-hole ratio and simplifies tooling logistics in multi-shift environments. Practical handling and workshop integration At just 0.383 kg, the tool body is easy to handle when mounting or during tool-change procedures while the 25 mm shank ensures secure clamping in standard holders. The combination of defined dimensions and a stable shank facilitates fast setup and repeatable positioning in both manual and automated toolholders. For operators less familiar with insert-based drilling, indexable systems replace the need for specialist regrinding and provide a predictable maintenance rhythm. For tailored advice on Teknik Cutting Tools' U608TM solid drill and fast delivery from Metav Werkzeuge in Emmerich, contact our consultants for machining recommendations and compatibility checks. Technical data Article number: U608TM Manufacturer: Teknik Cutting Tools (Teknik Makina) Product: Vollbohrer (solid drill) Core dimensions Diameter: 20 mm Overall length: 159 mm Cutting length: 80 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.383 kg Compatibility & features Compatible inserts: WCM-0402 Compatible insert manufacturer: Korloy Designed for indexable insert drilling FAQ Which insert type fits this drill? The U608TM accepts WCM-0402 indexable inserts; the tool body is compatible with inserts from Korloy. What are the overall and cutting lengths? Overall length is 159 mm and cutting length is 80 mm. What shank diameter is required for clamping? The tool uses a 25 mm shank and should be clamped in a holder suited for a 25 mm shank to ensure rigidity. Is this a solid or indexable drill? Although listed as a Vollbohrer, this drill body is designed for indexable-insert operation using WCM-0402 inserts. How heavy is the tool body? The U608TM has a mass of 0.383 kg, aiding handling during tool changes and setup. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of fast indexable insert changes, a rigid 25 mm shank for stable clamping and a compact Ø 20 mm cutting diameter to keep downtime low and cycle times consistent; order the tool via Metav Werkzeuge or consult our team for application-specific advice. Indexable Drill Body – Ø 20 mm, 25 mm shank, Teknik Makina Indexable Drill Body designed for short cutting engagements and reliable indexable-insert performance in production environments *Indexable inserts SOMT 0703 compatible *Ø 20 mm cutting diameter *Shank diameter 25 mm for secure clamping *Overall length 158 mm, cutting length 8 mm Reduced downtime through indexable-insert design The tool is configured to accept SOMT 0703 indexable inserts from Taegutec, which enables fast insert replacement without removing the drill body from the machine. This modular concept reduces maintenance time and improves process reliability because only the cutting edges are renewed when worn rather than the whole tool. The result is a measurable productivity improvement when short, repeatable hole cycles are required, and replacement inserts can be stocked economically to avoid production gaps. Rigidity and repeatability for consistent hole quality With a 25 mm shank and an overall length of 158 mm, the tool body is engineered for secure clamping and low run-out. The short cutting length (8 mm) concentrates cutting forces close to the spindle, which helps to stabilise the cut and maintain concentricity. The relatively light mass (0.387 kg) reduces spindle load during acceleration while retaining sufficient mass for vibration damping, supporting reproducible hole geometry in serial production. The solid mechanical concept is aimed at shops prioritising repeatability and tool life. Practical compatibility and simple procurement The drill body is listed under SKU U414TM and supplied by Teknik Makina. It is explicitly matched to SOMT 0703 inserts and the insert manufacturer Taegutec, which simplifies tool selection and spare-parts management. The compact cutting length and standard Ø 20 mm diameter make the body suitable for applications where short through-holes or small-depth drilling is common. For buyers seeking a reliable supply chain, Metav Werkzeuge provides consistent availability and technical guidance to integrate the tool into existing toolholders and changeover routines. For tailored technical advice or to secure the U414TM indexable drill body from Teknik Makina, contact Metav Werkzeuge in Emmerich by email (info@metav-werkzeuge.com) or phone (+49 2822 7131930) for personalised procurement and delivery support. Technical data Article number: U414TM Manufacturer: Teknik Makina Designation: Vollbohrer Dimensions & weight Diameter: 20 mm Overall length: 158 mm Cutting length: 8 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.387 kg Features & compatibility Compatible inserts: SOMT 0703 Compatible insert manufacturer: Taegutec SKU: U414TM FAQ What inserts fit this drill body? The drill body accepts SOMT 0703 indexable inserts; compatibility with Taegutec inserts is specified for efficient replacement. What is the nominal diameter and cutting length of the tool? The tool provides a Ø 20 mm nominal diameter with a cutting length of 8 mm, optimised for short-hole and shallow-depth operations. Which shank dimensions and clamping stability can be expected? The body features a 25 mm shank and a 56 mm shank length, offering secure clamping and improved repeatability for serial drilling. How is the U414TM identified for ordering and stock management? Order or reference the tool by SKU U414TM; the product is supplied by Teknik Makina and can be procured through Metav Werkzeuge. Is this tool suitable for high-volume production? Yes, the indexable-insert concept with SOMT 0703 inserts is designed to reduce downtime and enable rapid edge changes, supporting continuous production runs. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, purpose-built drill body that combines compatibility with ISCAR XC-- 10T304 indexable inserts, a secure Torx fastening system and workshop-ready dimensions to keep tool changes fast and production steady. Order or request advice via Metav Werkzeuge for rapid supply and compatibility checks. Solid drill body U050TM — compatible with XC-- 10T304 indexable inserts, 20 mm diameter (Teknik Makina) A solid drill body U050TM designed for indexable-insert drilling, offering a 20 mm working diameter and a total length of 102 mm for integration into standard tool systems. 20 mm diameter for standard metric drills Total length 102 mm, robust body design 56 mm shank length, 45 mm cutting length Compatible with ISCAR inserts, Torx T15 screw Consistent performance through indexable-insert compatibility The core advantage of this drill body is its direct compatibility with XC-- 10T304 indexable inserts, a choice that reduces downtime by enabling rapid insert changes without removing the tool from the spindle. Fitted to a robust body from Teknik Makina, the system supports predictable cycle times because insert replacement is fast and repeatable. For production environments that prioritise throughput, an indexable-insert solution reduces regrinding logistics and inventory pressure while maintaining cutting-edge surface finishes and dimensional consistency. Secure clamping and service-friendly fastening Secure mounting is achieved via a Torx T15 drive and an M4.5x11 fastening screw, a straightforward arrangement that simplifies maintenance and minimises the risk of loosening under machining loads. The 56 mm shank length provides a solid engagement in standard holders, improving run-out stability and thereby preserving the life of the inserts. This configuration supports efficient workshop routines: fewer tool changes, clearer maintenance steps and uncomplicated replacement procedures for operators and maintenance staff alike. Practical dimensions for seamless workshop integration Engineered with a 20 mm bore size, 102 mm overall length, 56 mm shank length and 45 mm cutting length, the body delivers a compact footprint suitable for a wide range of setups. At approximately 0.33 kg, the component is light enough for easy handling but substantial enough to resist vibration in many production scenarios. These dimensions make the body straightforward to stock and pair with existing holders and adaptors, helping to reduce the number of unique items in a tooling drawer and streamlining procurement and setup across multiple machines. Contact Metav Werkzeuge to discuss availability and ensure the Teknik Makina U050TM drill body fits the existing ISCAR XC-- 10T304 inserts and toolholders in the workshop Technical data Article number: U050TM Label: 20mm Vollbohrer XC-- 10T304 L102mm Manufacturer: Teknik Makina Eclass: 21180201 Facts Diameter: 20 mm Total length: 102 mm Shank length: 56 mm Cutting length: 45 mm Weight: 0.33 kg Special features Compatible with XC-- 10T304 indexable inserts Compatible insert manufacturer: ISCAR Torx key: T15 Torx screw: M4.5x11 FAQ Is this drill body compatible with ISCAR XC-- 10T304 inserts? Yes. The U050TM drill body accepts XC-- 10T304 indexable inserts and is specified for use with inserts from ISCAR, ensuring direct compatibility. What are the key dimensions of the drill body? The drill body has a 20 mm diameter, 102 mm total length, 56 mm shank length and 45 mm cutting length; weight is approximately 0.33 kg. Which fastening system secures the insert head? The insert is secured using a Torx T15 driver and an M4.5x11 screw, providing a service-friendly and reliable clamping method. Can this body be used in standard toolholders? Yes. With a 56 mm shank length and standard geometric proportions, the body integrates with typical workshop holders to provide stable engagement and run-out performance. What is the SKU for ordering or referencing this item? The product is listed under SKU U050TM, supplied by Teknik Makina and available through Metav Werkzeuge for European distribution. Teknik Makina: Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com