Gibt es einen Hahn und Kolb Online Shop?

Take advantage of the proven combination of left-hand cutting, 20 mm shank diameter and compatibility with 16–22ER indexable inserts for steady internal turning performance; order the SIL S20Q directly via Metav Werkzeuge or ask our consultants if needed SIL S20Q boring bar — 20 mm shank, left-hand cutting — Teknik Makina The SIL S20Q is a left-hand boring bar designed for 16–22ER indexable inserts, intended for internal turning and facing operations in workshop and production environments Left-hand cutting direction 20 mm shank diameter Compatible with 16–22ER indexable inserts 180 mm overall length Stable left-hand machining for repeatable accuracy The SIL S20Q is engineered for consistent performance in left-hand operations, making it suitable where reverse-direction cutting is required. The combination of the 20 mm shank and a 24 mm diameter body provides rigidity that reduces deflection during internal turning. This rigidity translates into improved surface finish and repeatability on serial parts, helping to maintain production tolerances and reduce scrap. Secure clamping and insert compatibility for reduced downtime Designed to accept 16–22ER indexable inserts and to interface with an ER16 clamping system, the tool offers straightforward insert changes and reliable seat stability. The 40 mm cutting height ensures adequate engagement for common insert sizes, while the robust clamping arrangement minimises vibration and the need for frequent re-adjustment, resulting in fewer interruptions on the shop floor. Optimised length and balance for workshop efficiency With a 180 mm overall length and a mass of approximately 0.445 kg, this boring bar balances reach and controllability for internal operations. The geometry has been conceived to assist chip control and steady cutting behaviour, which contributes to longer insert life and lower tooling costs per part. The tool’s dimensions support setups where access and rigidity must be reconciled without resorting to oversized holders. Practical handling and service considerations The bar’s ISO designation SIL S20Q and clear mechanical specification simplify tool selection for engineering teams and purchasing. Routine checks of clamping screws and insert seating are recommended to preserve cutting stability and tool life. If requirements are unclear or a specific machining task demands verification, Metav’s technical advisors are available to clarify compatibility and to recommend optimal insert grades and feeds For reliable left-hand internal turning with proven compatibility, contact Metav Werkzeuge for tailored technical advice and ordering; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: K330TM Manufacturer: Teknik Makina ISO designation: SIL S20Q Item description: Boring bar for indexable inserts (SIL for 16–22ER) Facts Shank diameter: 20 mm Overall length: 180 mm Body diameter: 24 mm Cutting height: 40 mm Weight: 0.445 kg Cutting direction: left Special features Compatible with 16–22ER indexable inserts ER16 clamping interface Designed for internal turning and facing Left-hand boring bar FAQ Which insert sizes are supported? The tool accepts 16–22ER indexable inserts; the SIL S20Q is specified for that range and seats ER-style cutters securely. What is the shank diameter and overall length? The boring bar has a 20 mm shank diameter and an overall length of 180 mm, providing a balance between reach and rigidity. Is the cutting direction left- or right-handed? This boring bar is configured for left-hand cutting, indicated by the tool geometry and ISO designation. Which clamping system is compatible? The bar interfaces with an ER16 clamping system, allowing straightforward integration into compatible toolholders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact solution that combines precise insert compatibility and robust shank stability to keep setups efficient and repeatable; the right-hand design and 20 mm shank ensure straightforward integration into existing tooling systems. Order the drill bar directly via Metav Werkzeuge or ask our consultants if needed. SIR S20P drill bar – for IR22 indexable inserts, 20 mm shank, 170 mm overall SIR S20P drill bar engineered for turning and boring applications with IR22 indexable inserts, providing a compact and rigid toolholder for standard industrial lathes and CNC turning centres. Compatible with 22 IR indexable inserts 20 mm shank diameter 170 mm overall length Right-hand cutting direction Consistent holemaking and repeatable results with indexable inserts The SIR S20P is designed to accept IR22 indexable inserts, delivering consistent cutting geometry across indexed tool changes. By using standardised inserts, the system reduces variability between cycles and shortens downtime caused by regrinding or reconditioning. The combination of a 20 mm shank and a proven insert clamping concept maintains axial rigidity, which translates into improved surface finish and a lower scrap rate for batch production. For shops migrating from solid drills, this modular approach offers faster retooling and predictable cycle times. Reduced setup time and secure clamping for reliable machining A clear benefit of the configuration is the simplified clamping and fastening: the cutting head is secured with an M4x11 screw driven by a Torx T15 key, ensuring repeatable torque application and stable insert retention. This fixed‑screw arrangement shortens tool change routines and reduces the risk of insert movement under load. The right‑hand cutting orientation supports conventional turning operations and is compatible with common machine tool setups, offering efficient chip evacuation and predictable cutting forces that protect both the workpiece and the toolholder. Practical handling, integration and workshop efficiency With an overall length of 170 mm and a nominal diameter of 24 mm, the tool balances reach and stiffness for many standard boring jobs, while its net mass of 0.433 kg keeps handling simple during setup. The ISO designation SIR S20P clarifies compatibility with existing tool libraries and CAM post‑processors, aiding rapid integration into production schedules. Supplied as a compact toolholder for indexable inserts, it supports cost‑effective maintenance strategies: only the inserts require regular replacement rather than the entire tool, reducing consumable waste and overall tooling spend. For expert advice on integrating the Teknik Makina SIR S20P into existing tooling setups or to arrange supply from Metav Werkzeuge, please contact our specialists via info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: K342-1TM Manufacturer: Teknik Makina ISO designation: SIR S20P Compatible inserts: 22 IR Facts Shank diameter: 20 mm Overall length: 170 mm Diameter: 24 mm Cutting height: 40 mm Weight: 0.433 kg Cutting direction: right Special features Torx key: T15 Torx screw: M4x11 Right-hand cutting orientation Suited for indexable insert systems FAQ Which indexable inserts fit this tool? The SIR S20P drill bar is designed for IR22 indexable inserts, ensuring secure seating and correct cutting geometry for repeatable results. What is the shank diameter and how does that affect clamping? The shank diameter is 20 mm; this size gives stable clamping in standard toolholders and collet systems while keeping the tool compact for confined setups. Is the tool suitable for left‑hand machining? No, the tool is specified for right‑hand cutting; left‑hand operations would require an alternative orientation or tool type. What fastening hardware is required for insert replacement? Insert clamping uses an M4x11 screw tightened with a Torx T15 key, enabling consistent torque and rapid insert changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust drilling solution that pairs a 24 mm working diameter with a 120 mm cutting length for reliable hole quality and fewer reworks; benefit from secure clamping via a 25 mm shank and standard mounting length for straightforward integration—order via Metav Werkzeuge or consult our specialists for configuration advice. Solid drill (Vollbohrer) by Teknik Cutting Tools — 24 mm, 120 mm cutting length Solid drill (Vollbohrer) for industrial machining applications, designed for use with indexable cutting inserts and compatible toolholders 24 mm working diameter for precise holes 120 mm cutting length for extended reach 25 mm shank for stable clamping Compatible with Korloy WCM-0503 inserts Consistent hole quality that reduces rework The combination of a 24 mm working diameter and a 120 mm cutting length delivers consistent hole geometry across serial production. A longer cutting length permits deeper passes without frequent tool changes, which improves throughput and reduces the risk of positional error. By focusing on dimensional consistency and chip evacuation, the tool helps maintain tight tolerances and lowers scrap rates, supporting reliable production schedules. Reduced tooling cost through insert compatibility Compatibility with Korloy WCM-0503 indexable inserts turns fixed-cost tooling into a serviceable system. Replacing worn inserts is faster and more economical than replacing entire solid-drill bodies, so maintenance intervals are shorter and cost per hole is lower. This modular approach also simplifies inventory: a single drill body can be paired with common insert grades for different materials, meaning fewer unique holders and a leaner tooling stock. Secure clamping and balanced geometry for steady cuts A 25 mm shank and 56 mm mounting length provide secure clamping in standard toolholders, while the 202 mm overall length balances reach with rigidity. The specified 0.465 kg mass supports stable spindle dynamics without excessive overhang, which helps limit runout and vibration. These mechanical characteristics contribute to improved surface finish and extend the service life of both inserts and the tool body. Practical benefits for workshop and production planning The U784TM configuration supports efficient tool management and predictable machine cycles. With clear specifications and straightforward insert matching, planning tool lists and spare-part kits becomes simpler. The modular setup not only reduces downtime for cutter changes but also aids in rapid reconditioning of worn components, fostering continuous production and a structured maintenance routine that aligns with industrial workflows. Contact Metav Werkzeuge for tailored advice and supply information: Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the U784TM and optimal insert grades for specific applications Technical data Article number: U784TM Brand: Teknik Cutting Tools Manufacturer: Teknik Makina Facts Diameter: 24 mm Cutting length: 120 mm Overall length: 202 mm Shank diameter: 25 mm Mounting length: 56 mm Weight: 0.465 kg Special features Compatible with Korloy WCM-0503 inserts Indexable-insert drilling concept Designed for industrial machining use FAQ What are the core dimensions of this drill? The U784TM Vollbohrer has a 24 mm diameter, a 120 mm cutting length and an overall length of 202 mm, listed under Teknik Cutting Tools Which inserts fit this tool? The drill is compatible with Korloy WCM-0503 inserts, enabling economical indexable insert changes for extended tool life What shank and mounting dimensions should the holder support? A 25 mm shank and a 56 mm mounting length are specified for secure clamping and correct seating of the U784TM body Is the tool suitable for deeper holes in serial production? With its 120 mm cutting length and balanced overall geometry, the drill supports medium-deep hole machining while maintaining repeatable accuracy How heavy is the tool and what does that mean for spindle dynamics? The U784TM weighs 0.465 kg; this moderate mass helps achieve stable spindle dynamics and reduced vibration for better surface finish Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable drilling performance with an indexable design: 24 mm cutting diameter, 25 mm shank and 96 mm cutting length deliver consistent chip removal and reduced tool change times. Compatible with SOMT 08T3 inserts from Taegutec, the tool balances modularity and rigidity to support productive shop-floor machining. Order or request technical advice directly via Metav Werkzeuge for fast, reliable supply. U420TM Indexable Drill Body – 24 mm diameter, 25 mm shank (Teknik Makina) The U420TM Indexable Drill Body is a modular drilling solution for industrial machining, designed for use with SOMT 08T3 indexable inserts and intended for stable, repeatable holemaking in workshop and production environments. 24 mm cutting diameter 25 mm shank diameter 96 mm effective cutting length Compatible with SOMT 08T3 inserts Faster throughput thanks to modular inserts and stable geometry The indexable design, accepting SOMT 08T3 inserts, enables quick insert changes and lower running costs compared with solid-carbide consumables. With a 25 mm shank and a centred construction, the tool provides improved clamping stability; the result is fewer vibrations and a reduced risk of premature wear. For operations where uptime matters, this combination of modularity and mechanical stability supports shorter cycle times and consistent hole quality. Consistent holemaking with engineered dimensions Precision in drilling is driven by controlled tool geometry: the 24 mm cutter diameter and 96 mm cutting length create a defined engagement volume, which simplifies speed-and-feed planning and enhances process reliability. The tool’s overall length of 174 mm and a shank length of 56 mm are specified to ensure correct seating in standard holders, while the modest weight (approx. 0.486 kg) aids in handling and balancing during set-up. These measurable values enable straightforward integration into existing machining routines. Shop-floor advantages in handling and maintenance By combining a standard shank size with a commonly available insert format, tool changes and inventory management become more efficient. The use of indexable inserts reduces scrap from regrinds and minimises downtime for reconditioning. Where exchangeability is important, the modular nature of this tool simplifies logistics: fewer complete tools are required, and insert stock can be kept small while covering a wide range of materials and conditions. Practical compatibility and specification guidance The drill body is specified for use with Taegutec-compatible inserts of the SOMT 08T3 type, providing a clear procurement path for replacement cutting edges. The measurable specifications—diameter, cutting length, shank diameter and overall length—make it simple to verify mounting and clearance in machine spindles or holders. For production environments seeking predictable performance, these defined tolerances and standards make planning and process control more straightforward. Contact Metav Werkzeuge for tailored supply of Teknik Makina indexable drill bodies (U420TM) or to discuss compatibility with existing tool holders and Taegutec SOMT 08T3 inserts; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: U420TM Manufacturer: Teknik Makina ECLASS: 21180201 Core specifications Cutting diameter: 24 mm Overall length: 174 mm Cutting length: 96 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.486 kg Special features Compatible with SOMT 08T3 indexable inserts Suitable for Taegutec insert formats Modular indexable drilling system FAQ What insert type fits this drill body? The U420TM drill body is designed for SOMT 08T3 indexable inserts; Taegutec-compatible inserts are commonly used with this model. Which shank size is required for mounting? This model features a 25 mm shank diameter and a shank length of 56 mm, matching standard holders for tools with that shank size. What are the key dimensions to verify before ordering? Check the 24 mm cutting diameter, 96 mm cutting length and the overall length 174 mm to ensure clearance and correct tool-seat engagement with the machine spindle. Is this tool supplied with inserts? The U420TM drill body is specified as an indexable tool body; inserts such as SOMT 08T3 are procured separately to match machining requirements. How does the modular design benefit production? Using the U420TM with indexable inserts reduces full-tool replacement costs and shortens maintenance times, improving process uptime and tool management. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a 24 mm cutting diameter with a 25 mm shank and a 48 mm effective cutting length, this solid drill offers stable clamping and consistent hole quality for indexable-insert operations; order directly via Metav Werkzeuge or consult our specialists for fitment advice. Teknik Makina Solid Drill U924TM — 24 mm, 25 mm shank The Teknik Makina Solid Drill U924TM is an insert-compatible drilling tool designed for machining applications that demand repeatable hole geometry and rapid insert changes 24 mm precise cutting diameter Compatible with SPMG 07T3 inserts 25 mm shank for stable clamping 48 mm effective cutting length Engineered for repeatable hole quality and productivity The U924TM is built to deliver consistent hole geometry through a balanced design that supports stable cutting conditions. With a 24 mm nominal diameter and an effective cutting length of 48 mm, the tool reduces variation between passes and helps maintain concentricity in series production. The combination of a rigid 25 mm shank and a compact overall length supports improved runout performance, which in turn reduces scrap rates and rework. Explained plainly, the robust shank diameter increases grip in the holder and improves torque transmission during the cut, leading to more reliable results on the shop floor. Fast insert changes and reduced downtime Designed to use SPMG 07T3 indexable inserts, the cutter simplifies maintenance and shortens downtime compared with solid-carbide solutions. Insert compatibility with established manufacturers such as Taegutec and YG-1 allows for quick replacement and easy sourcing of spare parts, accelerating tool turnaround. The insert system also makes it straightforward to adapt to different grades or edge preparations without withdrawing the entire tool from the spindle, supporting leaner inventory management and faster response to varying workpiece materials. Stability and chip control for cleaner machining A compact overall length of 130 mm and a focused cutting length support controlled chip formation and evacuation, particularly in medium-deep hole applications. The tool’s geometry is oriented towards steady cutting forces so that the holder, insert and workpiece stay aligned under load; this promotes cleaner chip flow and reduces the risk of chip re-cutting. For operations where surface finish and dimensional tolerance are important, this stability contributes directly to reduced secondary processing and higher first-pass yields. Practical choice for mixed production environments For workshops balancing diverse jobs, the U924TM provides an economical route to high availability: the indexable insert concept combines durable carrier design with low-cost consumables. The tool’s measurable features — diameter, cutting length and shank size — make it simple to specify and integrate into existing tooling setups. Combined with Metav’s distribution and technical competence, this cutter is well suited to small-batch and medium-volume production where predictability and fast serviceability are valued. Contact Metav Werkzeuge to confirm suitability for specific materials and to arrange supply directly from Emmerich; telephone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: U924TM Manufacturer: Teknik Makina Item name: Solid drill U924TM Compatible insert: SPMG 07T3 Compatible insert manufacturers: Taegutec, YG-1 Facts Diameter: 24 mm Overall length: 130 mm Cutting length: 48 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.382 kg Special features Indexable-insert design Rapid insert exchange Stable 25 mm shank for secure clamping Suited for repeatable holemaking FAQ What is the nominal diameter of this drill? The nominal diameter is 24 mm for the Teknik Makina Solid Drill U924TM. Which inserts does the tool accept? The cutter accepts SPMG 07T3 indexable inserts and is compatible with inserts from Taegutec and YG-1. How long is the effective cutting length? The effective cutting length is 48 mm on the U924TM. What shank size is required for the holder? The tool is supplied with a 25 mm shank diameter for secure clamping. Is the U924TM suitable for quick tool changes in production? Yes — the indexable-insert concept of the U924TM enables rapid insert exchange and reduced downtime. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Data inconsistency detected: the item is named as a "Vollbohrer" (translated: solid drill) while the data also lists compatibility with indexable inserts (WCM-0503) and an insert manufacturer (Korloy), which creates confusion regarding the actual nature of the product, as solid drills and tools designed for indexable inserts are fundamentally different in terms of design, functionality, and application; this discrepancy makes it impossible to generate a reliable and accurate product description, as the conflicting entries suggest a lack of clarity in the source data, potentially leading to misunderstandings or errors in usage, so it is essential to verify and correct the source data to ensure consistency and accuracy.

Benefit from precise, repeatable hole production thanks to the combination of a stable 25 mm shank, a generous 96 mm cutting length and compatibility with SPMG 07T3 inserts; order this tool via Metav Werkzeuge or contact our consultants for configuration advice. Indexable drill body (Ø 24 mm) — 25 mm shank, 96 mm cutting length | Teknik Makina The Indexable drill body (Ø 24 mm) by Teknik Makina is a robust tool body designed for industrial drilling with SPMG 07T3 indexable inserts, suitable for serial production and workshop use Ø 24 mm cutting diameter 25 mm shank diameter Compatible with SPMG 07T3 inserts 96 mm cutting length Consistent hole quality and longer tool life The U724TM indexable drill body delivers consistent hole geometry in repetitive operations by combining a precise tool datum with a rigid 25 mm shank. The Ø 24 mm cutting diameter and 96 mm cutting length balance deep-reach capability with stability, reducing vibration and improving surface finish. Using standard SPMG 07T3 inserts keeps tooling costs predictable: worn edges are replaced quickly without discarding the body, so cycle times remain stable and tooling budgets become easier to plan. Fast set-up and broad insert compatibility for production A compact clamping length of 56 mm and a total length of 178 mm enable straightforward tool change and reliable clamping in standard tool holders. The body accepts inserts from established manufacturers such as Taegutec and YG-1, supporting supply-chain flexibility and reducing downtime due to substitute parts. The tool’s modest mass (0.46 kg) contributes to lower spindle load during high-speed cutting, which helps maintain machining tolerances and extends bearing life on production machines. Practical benefits for shops and production planners Choosing this drill body reduces overall machining complexity: indexable inserts allow quick restoration of cutting performance, while the robust shank and body geometry improve repeatability and dimensional control. For operations that require predictable outputs and easy maintenance, the configuration supports lean tooling workflows and minimal in-process intervention. The standardized insert type simplifies inventory management and facilitates cross-compatibility with common insert suppliers used in modern machining environments. Contact Metav Werkzeuge for tailored advice on integrating the Teknik Makina U724TM into production workflows and to receive assistance with tooling selection and availability Technical data SKU: U724TM Manufacturer: Teknik Makina Diameter: 24 mm Overall length: 178 mm Weight: 0.46 kg Facts Shank diameter: 25 mm Cutting length: 96 mm Clamping length: 56 mm ECLASS: 21180201 Special features Compatible inserts: SPMG 07T3 Compatible insert manufacturers: Taegutec, YG-1 Suitable for indexable drilling operations SKU listed: U724TM FAQ What insert type does this drill body use? The drill body uses SPMG 07T3 indexable inserts; compatible manufacturers include Taegutec and YG-1. Is the shank suitable for standard tool holders? Yes, the body has a 25 mm shank diameter and a 56 mm clamping length designed for conventional holder interfaces. What hole diameter does the tool produce? The body is specified for a 24 mm cutting diameter and is designed for stable, repeatable holes in serial production. How deep can this tool cut effectively? With a 96 mm cutting length and a total length of 178 mm, the tool is intended for medium-depth drilling where rigidity and insert performance are required. Which SKU should be ordered for this configuration? Order the Teknik Makina tool under SKU U724TM for the configuration described above. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a robust Ø24 mm working diameter, 48 mm cutting length and a secure 25 mm shank for stable, repeatable drilling results; available via Metav Werkzeuge with technical consultation on demand. Indexable drill U116TM by Teknik Makina — Ø24 mm, WCM-0503 compatible Indexable drill U116TM for precision indexable insert drilling in production and workshop settings Indexable insert system WCM-0503 compatible Ø24 mm working diameter 48 mm effective cutting length 25 mm shank diameter for secure clamping Stable rigidity that secures process reliability The tool delivers a high level of stability through a compact overall length of 130 mm combined with a substantial 25 mm shank, which reduces vibration in heavy machining cycles. The measured 48 mm cutting length provides a controlled engagement depth for consistent hole quality while the moderate mass (approx. 0.39 kg) keeps dynamic loads manageable on the spindle. These construction details translate into fewer rejects and improved cycle-time predictability in CNC drilling operations. Lower tooling costs thanks to indexable inserts Designed around the standard WCM-0503 insert format, the drill reduces long-term tooling expenditure by permitting individual insert replacement rather than full-tool renewal. Compatibility with Korloy inserts simplifies procurement and inventory management, enabling rapid replacement during planned stoppages. The indexed insert concept also supports consistent edge geometry restoration, maintaining hole accuracy across multiple insert changes and thus improving overall equipment effectiveness. Flexible application in machining workflows The design suits series drilling tasks on modern machining centres where repeatability and uptime matter. With a Ø24 mm working diameter and a 25 mm clamping diameter, the tool is intended for secure chucking or holder systems that demand reliable clamping forces. The combination of 130 mm overall length and defined cutting zone helps integrate the tool into standard tool libraries and helps planners estimate reach and clearance without complex recalculation. The SKU U116TM identifies the configuration for ordering and documentation. For a dependable supply of Teknik Cutting Tools products and tailored technical advice on tool selection and compatibility, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss specification matching and delivery options. Technical data Article number: U116TM Manufacturer: Teknik Makina Dimensions & weight Diameter: 24 mm Overall length: 130 mm Cutting length: 48 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.39 kg Compatibility & features Compatible inserts: WCM-0503 Inserts manufacturer: Korloy Product type: Indexable drill SKU/UID: U116TM FAQ What insert type does the drill use? The drill is specified for WCM-0503 indexable inserts, compatible with standard Korloy inserts. What are the key dimensions to consider for setup? Essential measures are Ø24 mm diameter, 48 mm effective cutting length and 25 mm shank diameter; the overall length is 130 mm. Is the tool suitable for use in CNC machining centres? Yes — the tool’s shank and length combination is designed for secure clamping and predictable integration into CNC tool libraries. How is tool life maintained with this design? Tool life is extended by replacing individual WCM-0503 inserts rather than the whole tool body, preserving consistent cutting geometry between changes. Which SKU identifies this configuration for ordering? Order references should use SKU U116TM to ensure the correct indexable drill configuration. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise, repeatable holemaking with the Teknik Makina indexable insert drill body U824TM: a secure 25 mm shank and a 72 mm cutting length deliver efficient deep-hole production with quick insert changes. Order the indexable insert drill body directly via Metav Werkzeuge or ask our consultants if needed. Indexable Insert Drill Body U824TM – Ø24 mm, for SPMG 07T3 inserts (Teknik Makina) The Indexable Insert Drill Body U824TM is engineered for CNC machining centres and production lines where fast insert replacement and consistent hole quality are required. Compatible with SPMG 07T3 inserts Ø24 mm nominal diameter 25 mm shank for secure clamping 72 mm cutting length for deeper holes Increased throughput through optimised cutting geometry The U824TM drill body combines a Ø24 mm nominal diameter with a 72 mm cutting length, enabling longer effective engagement with the workpiece while maintaining stability. The use of indexable inserts means the cutting edge can be replaced in seconds, reducing machine downtime and lowering per-hole tooling cost compared with solid drills. This configuration supports a reliable production rhythm: fewer tool changes, shorter set-up windows and consistent hole tolerance across long runs. The result is measurable efficiency gains for batch production and repetitive machining tasks. Secure clamping and repeatable positioning for accuracy A 25 mm shank and a defined shank length of 56 mm provide a firm interface with toolholders, minimising runout and vibration during drilling cycles. The overall length of 154 mm and a compact tool weight of 0.446 kg balance accessibility with rigidity, helping to maintain concentricity and extend insert life. For workshops unfamiliar with insert tooling, the principle is straightforward: the body locates and supports the insert, while the insert delivers the cutting action — a design that separates wear items from the carrier and simplifies maintenance routines. Flexible compatibility to streamline inventory This drill body accepts the SPMG 07T3 insert format, compatible with established insert manufacturers Taegutec and YG-1, which simplifies reordering and keeps spare-part stocks compact. Using a standardised insert size allows a workshop to select grades and geometries appropriate to different tasks without changing the carrier, providing operational flexibility. The modular approach also reduces waste: only the small cutting insert is replaced when worn rather than the whole tool. Practical benefits for production planning and serviceability The U824TM’s design supports quick clamp-and-go replacement of inserts and straightforward reconditioning of the drill body when needed. For production planners this translates into predictable tool life cycles and easier cost calculations per component. Technically, the carrier supports accurate insert seating and stable cutting conditions; operationally, teams benefit from faster corrective actions at the machine and reduced dependence on specialist regrinding services. This combination of predictable performance and low-maintenance operation supports continuous workflow in busy workshops. For detailed technical advice on the Teknik Makina indexable insert drill body U824TM or to arrange supply from Metav Werkzeuge’s Emmerich warehouse, contact our consultants at Metav Werkzeuge by e‑mail or phone. Technical data SKU: U824TM Manufacturer: Teknik Makina Designation: Indexable insert drill body Core specifications Diameter: 24 mm Overall length: 154 mm Cutting length: 72 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.446 kg Features & compatibility Insert format: SPMG 07T3 Compatible insert manufacturers: Taegutec, YG-1 Item type: Indexable drill body FAQ What insert format does this drill body use? The drill body accepts SPMG 07T3 inserts; compatible insert grades from Taegutec and YG‑1 can be used depending on the application. Is the U824TM suitable for deep-hole drilling? With a 72 mm cutting length and 154 mm overall length, the U824TM is designed to reach deeper holes than short-form drill bodies while keeping stability and accuracy. Which shank diameter is required for clamping this tool? The carrier requires a 25 mm shank clamp interface and a shank length of 56 mm for secure mounting and repeatable positioning. Can different insert geometries be used with this carrier? Yes — the carrier accepts SPMG 07T3 inserts, allowing selection of insert grades and geometries for optimised cutting performance without changing the drill body. How does using an indexable drill body affect maintenance? An indexable carrier separates the wear element (the insert) from the tool body, so maintenance usually involves replacing small inserts rather than the entire tool, reducing cost and turnaround time. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of precise holemaking with a compact tool that combines a Ø 24 mm cutting diameter and a 96 mm cutting length for consistent, repeatable results; the robust 25 mm shank and 178 mm overall length ensure stable clamping and easy integration into standard toolholders. Order the tool directly via Metav Werkzeuge or consult the technical team for application advice. Indexable drill (Vollbohrer) U616TM by Teknik Makina — Ø 24 mm, overall length 178 mm A versatile indexable drill designed for industrial drilling operations where consistent hole quality and secure shank fixation matter, compatible with Korloy inserts WCM‑0503 Ø 24 mm precision drilling Cutting length 96 mm for deep holes Shank Ø 25 mm, 56 mm shank length Compatible with Korloy WCM‑0503 inserts Consistent hole quality through defined cutting length The tool delivers a 96 mm cutting length, which is intended to produce consistent chip control and repeatable hole dimensions in serial production. By fixing the cutting zone to a predictable length, the design reduces the risk of over‑penetration and helps maintain perpendicularity in through and blind holes. The combination of a defined cutting zone and a standardised shank diameter supports reliable toolholding, which in turn improves finished‑part tolerances and reduces rework rates. Stable clamping and machine integration for uninterrupted machining With a 25 mm shank diameter and a shank length of 56 mm, the carrier is dimensioned for secure clamping in commonly used toolholders and adaptors. A firm clamping area minimises run‑out and vibration, translating into longer insert life and more consistent surface finish. The tool’s 178 mm overall length balances reach and rigidity, making it suitable for medium‑depth drilling tasks while preserving stability in CNC and turret applications. Practical versatility via insert compatibility Compatibility with Korloy WCM‑0503 inserts provides clear advantages for workshops that require rapid index changes and predictable cutting geometry. The use of indexable inserts allows faster on‑site service life restoration compared with regrinding solid tools, offering productivity gains in high‑mix production. The carrier is listed under SKU U616TM, enabling straightforward identification in procurement systems and spare‑parts planning. Designed to support productive workflows in professional shops Engineered for industrial environments, the tool assists in reducing machine downtime through predictable maintenance cycles and straightforward insert replacement. Its moderate weight (approx. 0.425 kg) and standardised interface facilitate handling and storage, while the dimensional data support rapid programming and tool‑path verification. The clear specifications make the item simple to integrate into tool lists and CAM libraries, removing ambiguity from production planning. Contact Metav Werkzeuge for a technical appraisal or to arrange immediate supply of the U616TM indexable drill from our Emmerich distribution — technical advice and order handling are available via Metav Werkzeuge. Technical data SKU: U616TM Product name: Vollbohrer Manufacturer: Teknik Makina ECLASS: 21180201 Facts Diameter: 24 mm Overall length: 178 mm Cutting length: 96 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.425 kg Special features Compatible with Korloy WCM‑0503 inserts Suitable for indexable drilling applications Compact overall length for medium‑depth holes FAQ Which inserts fit this tool? The carrier is compatible with Korloy WCM‑0503 inserts; insert seating and clamping follow the Korloy specification for that grade. What are the key dimensions to reference when programming? Use the Ø 24 mm diameter, 96 mm cutting length and 178 mm overall length (shank Ø 25 mm, shank length 56 mm) for tool‑path and collision checks. Is the tool suitable for deep hole drilling? The moderate overall length and 96 mm cutting length make the tool suited to medium‑depth holes; for deeper reaches, alternative tool geometries should be considered. How is the tool identified for reordering and inventory? The item is listed as SKU U616TM which should be used for procurement and spare‑parts tracking. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise T‑slot cutting, proven insert compatibility and straightforward serviceability to keep set‑ups fast and production steady. Order the cutter through Metav Werkzeuge or ask our advisors for a tailored specification check. T‑slot cutter — 24 mm diameter, for SCMT 09T3 indexable inserts (Teknik Makina) A T‑slot cutter designed for machining standard T‑slots with SCMT 09T3 indexable inserts, suitable for CNC and workshop milling operations where repeatable slot geometry and quick insert changes are required 24 mm cutting diameter for standard T‑slots Compatible with SCMT 09T3 indexable inserts 20 mm shank for secure clamping 100 mm overall length with 35 mm cutting length Accurate slot profiles with proven insert compatibility The cutter delivers consistent T‑slot geometry by using the widely available SCMT 09T3 indexable inserts, enabling predictable cutting behaviour and straightforward replacement. The 24 mm cutting diameter combines a compact footprint with adequate stock removal for common T‑slot sizes, which simplifies tooling choices across jobs. By relying on standard inserts, tool procurement and inventory management are eased, supporting a reliable production flow and shorter machine downtime. Secure mounting and simple upkeep for uninterrupted work A 20 mm shank provides rigid clamping in standard toolholders, improving concentricity and reducing vibration during milling. The insert is fixed with an M3.5x8.5 screw secured using a T15 Torx key, a configuration that keeps changeovers fast and repeatable. These design choices reduce set‑up time and make routine maintenance straightforward, which translates into higher machine utilisation and more predictable scheduling on the shop floor. Cutting geometry tuned for clean T‑slot edges The cutter’s 55° cutting angle and single‑edge configuration are optimised to form the T profile with minimal burr formation and reliable clearance beneath the slot head. The geometry balances shear and chip evacuation to produce a consistent slot profile across a run of workpieces. For machinists unfamiliar with angle effects, a 55° approach gives a compromise between positive cutting action and durable edge life for intermittent slotting tasks. Practical dimensions and workshop advantages With an overall length of 100 mm and a cutting length of 35 mm, the tool suits both through‑slotting and partial‑depth operations while keeping tool overhang manageable. The modest mass (0.182 kg) makes handling and tool changes easy in a busy production environment. Supplied under SKU TKC191TM by Teknik Makina, this cutter integrates into existing toolsets without adding complexity, supporting quicker changeovers and consistent machining results. Contact Metav Werkzeuge for a specification check, delivery options and to secure the Teknik Makina T‑slot cutter (SKU TKC191TM) from our Emmerich stock. Technical Data Article number: TKC191TM Brand: Teknik Makina Product type: T‑slot cutter Model: 24mm T‑slot cutter for SCMT 09T3 indexable inserts ECLASS: 21180605 Facts Diameter: 24 mm Overall length: 100 mm Shank diameter: 20 mm Cutting length: 35 mm Weight: 0.182 kg Cutting angle: 55° Number of cutting edges: 1 Special features Compatible with SCMT 09T3 indexable inserts Torx screw: M3.5x8.5 Torx key: T15 SKU: TKC191TM FAQ Which inserts fit this T‑slot cutter? The cutter is designed for SCMT 09T3 indexable inserts; using these standard inserts ensures correct seat geometry and cutting performance. What shank size does the cutter require? The tool has a 20 mm shank diameter, suitable for holders and collets that accept a 20 mm shank. How is the insert secured? The insert is fixed with an M3.5x8.5 screw tightened using a T15 Torx key to ensure secure and repeatable clamping. What is the SKU and who supplies this cutter? The cutter is supplied as SKU TKC191TM by Teknik Makina and offered via Metav Werkzeuge. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of solid-carbide construction and internal coolant for reliable internal threading and minimal downtime; order the KE75TM directly via Metav Werkzeuge or request specialist advice from Metav consultants for seamless integration into production. KE75TM Thread boring bar – solid carbide, internal coolant (Teknik Makina) The KE75TM is a solid-carbide thread boring bar for internal thread turning applications on CNC lathes, compatible with 16 IR indexable inserts and designed for right-hand cutting. Solid-carbide body for high rigidity Internal coolant for improved chip evacuation Compatible with 16 IR indexable inserts 24 mm nominal diameter, 250 mm overall length Delivering repeatable internal threads with indexable inserts The KE75TM combines a solid-carbide blank with an indexable‑insert system to produce consistent internal threads while reducing set‑up time. The tool accepts 16 IR inserts, which simplifies replenishment and keeps downtime low. With a cutting height of 13.7 mm, the geometry supports positive insert clamping and predictable engagement. This configuration translates into stable thread form, fewer rejects and a measurable increase in process reliability for serial production. Better chip control and cooling for uninterrupted cycles Integrated internal coolant channels direct cutting fluid to the cutting edge, which improves heat dissipation and chip control during internal thread turning. For right-hand cutting operations, targeted coolant flow helps prevent chip nest formation inside bores, reducing rework and improving surface finish. The result is longer insert life and a steadier cycle time, particularly on demanding materials where thermal management is critical. Robust shank and compact dimensions for confined bores Designed with an E20S shank and a 20 mm tool holder diameter, the bar presents a compact footprint while maintaining torsional stiffness. The nominal diameter is 24 mm and the overall length is 250 mm, making it suitable for deeper internal threading tasks without excessive overhang. At approximately 0.56 kg, the component balances mass and rigidity, offering improved vibration damping compared with lighter holders — an advantage when repeatability is required across series parts. Engineered for production environments and straightforward assembly The KE75TM features right-hand cutting and is supplied with the necessary fastenings: a Torx‑head screw (M3.5x11) secured with a T15 key. The tool pairs with IR16 clamping holders and a reference backing plate (TA060), enabling rapid installation and secure insert retention. For workshop planners, the combination of a solid-carbide blank and indexable inserts offers a cost-effective route to high-quality internal threads while keeping inventory management predictable. Contact Metav Werkzeuge for sourcing the Teknik Makina KE75TM threading bar with technical consultation and delivery from Emmerich; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: KE75TM Manufacturer: Teknik Makina Material: Solid carbide Type: Thread boring bar for internal threads ISO designation: E20S Compatible inserts: 16 IR Facts Diameter: 24 mm Overall length: 250 mm Shank diameter (holder): 20 mm Cutting height: 13.7 mm Weight: 0.56 kg Cutting direction: right Torx key: T15 Torx screw: M3.5x11 Special features Internal coolant For indexable inserts 16 IR Compatible clamping holder designation IR16 Backing plate reference TA060 Pass ring BSP010 Suited to internal thread turning on CNC lathes FAQ What inserts fit this boring bar? The KE75TM thread boring bar is specified for 16 IR indexable inserts and is delivered to work with the corresponding clamping holder designation IR16. Is internal coolant available with this tool? Yes, the KE75TM features internal coolant to improve chip evacuation and tool life during internal thread machining. Which machines is the bar intended for? This solid‑carbide boring bar is intended for CNC lathes and turning centres where compact, rigid tooling for internal threads is required; the E20S shank fits standard toolholders used in such setups. What are the key dimensions to check before ordering? Verify the 24 mm nominal diameter, 250 mm overall length and the 20 mm shank/holder diameter to ensure compatibility with existing tool turrets and holders when integrating the KE75TM. Which screw and key are required for insert clamping? Insert clamping uses an M3.5x11 Torx screw tightened with a T15 key, supplied for secure and repeatable clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a rigid Ø20 mm shaft, secure compatibility with CNMG 1204 inserts and a compact 200 mm overall length, this boring bar delivers stable cuts and predictable tool life for turning applications. Order the tool via Metav Werkzeuge or request technical advice from their consultants for immediate supply from Emmerich. Boring bar PCLN for CNMG indexable inserts — Teknik Makina S20R PCLNR, Ø20 mm The boring bar PCLN for CNMG Indexable Inserts is a right‑hand turning tool designed for CNMG 1204 inserts, offering a compact 200 mm length and a robust Ø20 mm shank for secure clamping in common toolposts and turrets. Shaft Ø20 mm for rigid clamping Designed for CNMG 1204 indexable inserts 200 mm overall length for versatile reach Without internal coolant for external supply Stable clamping for consistent machining results A toolholder built around a Ø20 mm shank provides improved rigidity, reducing chatter during heavy cuts and finishing passes. The ISO designation S20R PCLNR indicates a standard shank and head layout that fits many lathe toolposts; this makes fixture planning straightforward and repeatable. By lowering vibration and deflection, the design contributes directly to extended insert life and more predictable surface finishes, which reduces rework and downtime on production batches. Compatibility with CNMG 1204 inserts for flexible turning Prepared for CNMG 1204 indexable inserts, the turning bar accepts a widely available insert geometry that suits roughing and finishing when matched to the appropriate grade. The tool’s 95° cutting angle and right‑hand cutting direction support conventional turning setups and stable plunge behaviour. Because the bar is specified without internal coolant, cooling strategy is external by design — this simplifies the holder construction and is ideal for dry machining or systems where coolant is supplied externally. Practical dimensions that suit busy workshops With a 200 mm overall length and a nominal diameter of 24 mm at the head, the holder balances reach and stiffness for internal or external operations in confined setups. The 50 mm cutting height and the modest weight of 0.54 kg make handling and tool changes easy for technicians while keeping centre‑of‑gravity shifts minimal when mounted. These dimensions support quicker set‑ups and predictable toolpaths, improving throughput without compromising process stability. Built for professional workflows and reliable supply Manufactured by Teknik Makina and stocked by Metav, the holder is aimed at machining centres and workshops that demand dependable tooling ready for immediate use. The simple construction—no internal coolant—reduces potential leak paths and maintenance points, while the standard geometry ensures compatibility with established clamping systems. Combined with Metav’s logistics and technical support, this solution is suitable for integration into both single‑machine shops and serial production environments. Contact Metav Werkzeuge for tailored machining advice and fast supply from Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number (SKU): P338TM Brand: Teknik Makina ISO designation: S20R PCLNR Facts Shaft diameter: 20 mm Cutting height: 50 mm Overall length: 200 mm Weight: 0.54 kg Head diameter: 24 mm Cutting angle: 95° Cutting direction: right Special features Fits CNMG 1204 indexable inserts Without internal coolant Suitable for standard toolpost mounting Compact design for internal and external boring FAQ What insert type does this boring bar accept? The Tek­nik Ma­ki­na boring bar is designed for CNMG 1204 indexable inserts, allowing use of standard grades for roughing or finishing. Is this holder suitable for internal boring in small bores? Yes, with its 200 mm overall length and compact head diameter the bar is suitable for many internal and external turning setups where reach and rigidity must be balanced. Does the tool provide internal coolant feed? The holder is specified without internal coolant; coolant must be supplied externally or omitted for dry machining applications. Which cutting direction does the tool support? The bar is configured for right‑hand cutting, matching typical lathe feed directions for conventional turning operations. What is the ISO designation and why is it relevant? The S20R PCLNR designation describes the shank and head form, ensuring compatibility with standard toolpost clamping systems and aiding selection for machine setups. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of robust compatibility and tight finishing capability for a reliable internal boring cycle; the combination of a CCMT 0602 indexable insert system, a diameter range of Ø25–32 mm and a compact overall length of 72 mm supports stable, repeatable results in steel turning. Order directly via Metav Werkzeuge or consult the technical team for application-specific advice. Boring tool for CCMT 0602 indexable inserts (THKB102TM) — Ø25–32 mm, M12 by Teknik Makina The Boring tool for CCMT 0602 indexable inserts is an internal boring bar engineered for precision steel machining and finishing across a 25–32 mm diameter band Compatible with CCMT 0602 indexable inserts Diameter range Ø25–32 mm Fine finishing capability 0.02 mm M12 mounting, overall length 72 mm High-precision finishing for repeatable tolerances This boring bar is designed to deliver consistent surface quality and dimensional accuracy when working on steel components. With a declared fine finishing capability of 0.02 mm, the tool enables tight tolerance attainment in finishing passes; the specification indicates the achievable surface control rather than a guaranteed single-cycle tolerance, and is best interpreted within a defined machining strategy (cutting data, insert geometry, clamping and machine rigidity). The use of indexable inserts reduces set-up time and keeps process repeatability high: worn edges can be replaced without regrinding the holder, maintaining productivity while controlling cost per part. The focus on measurable finishing performance supports planning for downstream processes such as heat treatment or assembly. Secure mounting and flexible application range The holder accepts standard CCMT 0602 inserts and is engineered for secure attachment via an M12 thread, providing a rigid connection that limits vibration and improves tool life. The tool’s effective working span covers Ø25–32 mm, which makes it suitable for common internal boring diameters encountered in component manufacturing. Shorter overhang and a compact 72 mm overall length reduce leverage at the cutting edge, lowering the risk of chatter and enabling higher surface quality at typical cutting speeds for steel. For workshops employing indexable turning systems, the component simplifies inventory by aligning with widely used insert types and geometries. Built for stable steel turning with efficient handling Constructed for demanding steel machining tasks, the holder balances rigidity with a low mass—its listed weight of 0.194 kg contributes to easier handling during tool changes while preserving stability during cuts. The indexable insert concept means faster recovery from tool wear and straightforward insert replacement, which supports continuous operation on production lines and small-batch shops alike. Where attention to cycle time and part quality is required, the combination of compatible insert format and compact geometry allows process optimisation: fewer tool change interruptions and predictable finishing outcomes support higher overall throughput and lower scrap rates. For application-specific recommendations or to procure the Teknik Makina boring tool THKB102TM through Metav Werkzeuge, request a tailored machining consultation from the Emmerich team or arrange purchase via the Metav Werkzeuge sales desk. Technical data Article number: THKB102TM Manufacturer: Teknik Makina ECLASS: 21041590 Facts Diameter range: Ø25–32 mm Overall length: 72 mm Thread: M12 Fine finishing: 0.02 mm Weight: 0.194 kg Special features Compatible with CCMT 0602 indexable inserts Suitable for steel machining Indexable insert system for fast edge changes Compact design for reduced overhang FAQ What insert type fits this boring holder? The holder is compatible with CCMT 0602 indexable inserts; the design accepts the standard CCMT insert geometry used in turning and finishing applications. Which diameter range is covered by the tool? Internal machining across Ø25–32 mm is supported, making the tool suitable for medium-diameter bore finishing and turning operations. What is the declared finishing capability? A fine finishing capability of 0.02 mm is specified, which refers to achievable control during finish passes under appropriate machining conditions with correct insert geometry and machine rigidity. How is the tool secured in the spindle or adapter? Mounting is provided via an M12 thread, offering a rigid connection that reduces vibration and supports stable cutting performance. Is this tool suitable for heavy roughing operations? The design is optimised for finishing and internal boring where indexable inserts and reduced overhang are advantageous; for heavy roughing, a holder with a larger cross-section or specific roughing geometry is generally recommended. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining precise indexable capability for Korloy WCM-0503 inserts with a 25.5 mm cutting diameter and a 75 mm effective cutting length, this insert drill body supports consistent holemaking and reduced changeover times. Order the tool directly via Metav Werkzeuge or consult our specialists for integration advice. Insert Drill U161TM — indexable insert drill body, 25.5 mm diameter, Teknik Makina The Insert Drill U161TM is an indexable drilling solution designed for production tooling and CNC applications, offering a compact overall length and a robust shank interface for stable clamping Indexable drill body for WCM-0503 inserts 25.5 mm cutting diameter 75 mm effective cutting length Robust 25 mm shank, 158 mm overall Consistent drilling performance for production work The U161TM is engineered to support repeatable hole quality across medium- to long-run operations. With a 25.5 mm cutting diameter and a 75 mm cutting length, the design balances rigidity and reach to reduce deflection in typical drilling cycles. The combination of a substantial 25 mm shank and a 158 mm overall length maintains stable clamping in standard toolholders, which contributes to consistent concentricity and predictable process windows. Where cycle time and part tolerances are critical, the indexable concept removes the need for frequent full-tool replacement and shortens machine downtime. Designed for fast insert changes and dependable clamping Compatibility with Korloy WCM-0503 indexable inserts ensures quick tip replacement and predictable cutting geometry. The insert interface is designed to allow rapid indexing and secure seating, reducing setup time when multiple holes or different coatings are required. A 56 mm holder engagement length gives a clear datum for tool change systems and supports firm axial support in collets or hydraulic chucks. The result is lower fixture time, easier maintenance of cutting edges and a straightforward path to repeatable production results with minimal operator intervention. Reliability and supply advantages from Metav Sourcing through Metav Werkzeuge brings a transparent supply chain and practical technical support from a European distribution hub. Metav’s inventory and quality-filter approach streamlines procurement for workshops and industrial buyers, while the company’s extensive product range helps reduce supplier overhead. For purchasers seeking tooling that fits existing machining strategies, the insert drill body integrates with standard indexable workflows and benefits from Metav’s stock visibility and logistics centred in Emmerich, ensuring dependable delivery and traceable quality throughout the purchasing process. For availability, technical integration guidance or to request a quotation for the Teknik Makina U161TM insert drill body, contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application-specific requirements Technical data Article number: U161TM Manufacturer: Teknik Makina Facts Diameter: 25.5 mm Cutting length: 75 mm Shank diameter: 25 mm Shank engagement length: 56 mm Overall length: 158 mm Weight: 0.49 kg Special features Compatible with Korloy WCM-0503 inserts Indexable insert drill body design Suitable for production and CNC toolholders FAQ Which inserts fit this drill body? This insert drill body is compatible with WCM-0503 indexable inserts; Korloy inserts are specified for the standard seating and geometry of the U161TM. What are the key dimensions of the U161TM? The U161TM features a 25.5 mm cutting diameter, 75 mm cutting length, 25 mm shank diameter and a total length of 158 mm. What clamping interface is required? The tool uses a 25 mm shank with a 56 mm engagement length suited to standard holders and systems that accept this shank diameter. Is the insert drill body designed for quick tip replacement? Yes — the indexable design allows rapid insertion and indexing of WCM-0503 inserts, reducing changeover time and simplifying maintenance. How heavy is the U161TM and what is its SKU? The U161TM weighs approximately 0.49 kg and is listed under SKU U161TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Achieve dependable holemaking with a 25.5 mm cutting diameter and a 75 mm cutting length, combining consistent performance and straightforward insert replacement. Compatibility with SPMG 07T3 indexable inserts and leading makers like Taegutec and YG-1 reduces tooling downtime and total machining cost. Order or request specification support directly via Metav Werkzeuge for reliable supply and expert advice. Indexable insert drill U825-1TM — Ø 25.5 mm, 75 mm cutting length by Teknik Makina The indexable insert drill is engineered for medium-depth drilling in workshop and production environments, offering fast insert changes and stable mounting for repeatable hole quality 25.5 mm cutting diameter 75 mm cutting length 158 mm overall length Compatible with Taegutec and YG-1 inserts Accurate holes through controlled cutting geometry The U825-1TM is built to deliver consistent hole quality thanks to its defined cutting geometry and a comparatively long engagement length. With a Ø 25.5 mm cutting diameter and 75 mm cutting length, the tool is intended to provide repeatable results when used in appropriately configured drilling fixtures. The controlled chip formation achieved with indexable cutting edges reduces the risk of rework, so production throughput can be increased while maintaining dimensional tolerances. The combination of cutting diameter and engagement length means fewer tool changes for medium-depth applications, which contributes directly to improved line efficiency. Flexible, cost-efficient insert system for quick turnarounds Designed around standard indexable inserts, this drill accepts SPMG 07T3 plates, a widely available format that allows economical wear management. Compatibility with Taegutec and YG-1 inserts ensures access to a broad range of grades and geometries for different materials and cutting conditions. The replaceable-edge concept separates the expensive body from the consumable cutting edges, enabling predictable tool costs per hole and simplified inventory management. Insert replacement is fast and reduces machine downtime, delivering a tangible cost-benefit in series production and batch work alike. Robust shank and practical mounting for reliable handling Key mechanical dimensions support straightforward integration with standard tooling systems: a 25 mm shank diameter with 56 mm shank length, an overall length of 158 mm and a tool weight of 0.467 kg. These proportions make the drill suitable for common toolholders that accept a 25 mm shank while keeping runout and clamping forces within typical workshop tolerances. The compact overall length is helpful where access is limited, while the modest mass aids stability and handling during tool changes. Clear technical parameters permit quick verification of fixture compatibility and help planners reduce setup time. Specify the Teknik Cutting Tools indexable insert drill U825-1TM via Metav Werkzeuge for dependable supply and expert consultation — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: U825-1TM Manufacturer: Teknik Makina ECLASS: 21180201 Dimensions & weight Cutting diameter: 25.5 mm Cutting length: 75 mm Overall length: 158 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.467 kg Compatibility & features Insert type: SPMG 07T3 Compatible insert makers: Taegutec, YG-1 SKU: U825-1TM FAQ What insert type does this drill use? The drill uses SPMG 07T3 indexable inserts; replacement inserts of this format can be fitted quickly to restore cutting performance. Which insert manufacturers are compatible? Compatibility is specified for Taegutec and YG-1, ensuring access to multiple grades and geometries for varied machining tasks. What are the key dimensions and weight? Key data for the U825-1TM: Ø 25.5 mm cutting diameter, 75 mm cutting length, 158 mm overall length, 25 mm shank diameter, 56 mm shank length, weight 0.467 kg. Which toolholders will accept this drill? Holders that accept a 25 mm shank are suitable; the specified shank length of 56 mm supports secure clamping in common toolholders. Is this drill suited to deep-hole drilling? With a 75 mm cutting length, the tool is best described as suitable for medium-depth holes rather than specialised deep-hole drilling applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of robust cutting stability and efficient chip control thanks to the internal coolant design, combined with proven compatibility for LNMX 1004 inserts — ideal for continuous production runs. Order or request expert advice directly from Metav Werkzeuge to ensure the right configuration for the application. Indexable milling cutter – 32 mm shank, internal coolant (Teknik Makina) A versatile indexable milling cutter engineered for use with LNMX 1004 indexable inserts, designed to deliver steady metal removal and reliable coolant-fed machining in industrial milling operations 32 mm shank diameter Internal coolant for improved chip evacuation Compatible with Korloy LNMX 1004 inserts 250 mm overall length, 80 mm cutting length T15 Torx screws M4x10 for secure fastening Stable tool geometry for predictable material removal The body is built around a 32 mm shank and a 250 mm overall length, providing the rigidity required for repeatable milling tasks. With four cutting edges, this cutter offers balanced engagement that reduces vibration and helps maintain concentricity during roughing and light finishing passes. The robust construction supports consistent cut depths and tool life stability, making it suitable for workshop and light industrial environments where predictable performance is a priority. Coolant-through design that enhances surface quality and uptime A dedicated internal coolant channel directs fluid precisely to the insert seating area to optimise chip evacuation and cooling at the cutting zone. That targeted cooling reduces edge temperature, which in turn helps preserve insert life and surface integrity of the workpiece. For operations where cycle stability and reduced rework are essential, this coolant-fed arrangement improves process reliability and can contribute to fewer unscheduled tool changes. Practical compatibility and workshop integration for fast setup Designed specifically for Korloy LNMX 1004 indexable inserts and supplied with the matching fastening specification (T15 Torx, M4x10 screws), the tool simplifies procurement and assembly. The cutter provides an 80 mm cutting length and a compact, manageable weight of 1.2 kg, enabling straightforward handling and quick changeovers on milling spindles that accept a 32 mm shank. The SKU S096TM identifies this configuration for ordering and inventory control. For tailored procurement of this Teknik Makina indexable milling cutter with internal coolant, contact Metav Werkzeuge for expert guidance and supply directly from Emmerich to the workshop bench. Technical data SKU: S096TM Manufacturer: Teknik Makina Product type: Indexable milling cutter Weight: 1.2 kg Compatible inserts: LNMX 1004 (Korloy) Core dimensions Shank diameter: 32 mm Overall length: 250 mm Cutting length: 80 mm Number of cutting edges: 4 Features and fittings Internal coolant Torx key: T15 Torx screw: M4x10 Compatible with Korloy inserts (LNMX 1004) Category: Milling cutters FAQ What inserts are suitable for this cutter? The indexable milling cutter is designed for LNMX 1004 inserts and is compatible specifically with Korloy LNMX 1004 geometry. Does the tool support coolant-through machining? Yes, the cutter features internal coolant to direct fluid to the cutting zone for improved chip evacuation and temperature control. What are the key dimensions to check before mounting? Verify the 32 mm shank diameter and the 250 mm overall length to ensure spindle compatibility and sufficient projection for the intended operation. Which fastening hardware is specified for the inserts? The cutter uses T15 Torx fastening and M4x10 screws for secure attachment of LNMX 1004 inserts. How is the tool identified for ordering? This configuration is listed under SKU S096TM, Teknik Makina, and is available through Metav Werkzeuge for procurement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, purpose-built boring solution that combines precision finishing, compatibility with CCMT 09T3 indexable inserts and a robust overall length for stable setups; order directly via Metav Werkzeuge or consult their specialists for specification matching and delivery from Emmerich. Finishing Boring Bar THB132TM — Ø250 mm, for CCMT 09T3 indexable inserts (Teknik Makina) Finishing Boring Bar THB132TM is a purpose-designed internal turning tool for high-precision finishing operations in metalworking, optimised for CCMT 09T3 indexable inserts and compact machine configurations. Precision internal finishing tool Compatible with CCMT 09T3 inserts Compact 212 mm overall length Suitable for up to Ø310 mm cutting diameter High-precision finishing for internal bores The THB132TM is engineered for fine machining of internal diameters where consistent surface quality and tight tolerances are required. Its compatibility with CCMT 09T3 indexable inserts enables reproducible results and economical insert changes. In practise, the combination of a stable tool body and proven insert geometry reduces vibration and helps achieve uniform surface finish, which in turn minimises secondary operations and rework. Compact design that improves machine accessibility With an overall length of 212 mm and a nominal tool diameter of 250 mm, this boring bar is designed for use in restricted or short overhang applications. The reduced projection helps maintain rigidity, lowering the risk of chatter and improving tool life. For setups where space is limited, the compact profile provides the pragmatic advantage of enhanced accessibility without sacrificing the cutting envelope, which reaches up to Ø310 mm. Clear productivity gains with indexable technology Using standard CCMT inserts, the tool delivers fast, repeatable index changes and consistent geometry across production batches. Indexable inserts mean lower downtime for tool management and predictable cost control per part. The THB132TM’s design supports straightforward insert clamping and replacement, enabling efficient process planning and a measurable uplift in throughput for finishing operations. Practical suitability across common finishing tasks The boring bar is suitable for precision turning tasks on components requiring fine internal surfaces and form accuracy. Its geometry and insert compatibility make it well suited to finishing cast and machined workpieces where tight dimensional stability is critical. The specification emphasises operational reliability and straightforward integration into existing turning centres, helping maintain production continuity and part quality. Contact Metav Werkzeuge for a tailored delivery and technical match from Emmerich for Teknik Cutting Tools' THB132TM finishing boring bar Technical data Article number: THB132TM Label: 250mm Ausdrehwerkzeug für die Feinbearbeitung CCMT 09T3 L212mm Description: Finishing boring tool for CCMT 09T3 indexable inserts eClass: 21041590 Facts Diameter: 250 mm Total length: 212 mm Maximum cutting diameter: 310 mm Cutting height: 142 mm Special features Compatible with CCMT 09T3 indexable inserts Product type: Finishing boring tool Manufacturer: Teknik Makina SKU: THB132TM UID: THB132TM FAQ Is this boring bar suitable for finishing internal diameters on small lathes? The THB132TM is designed for compact setups and, with its 212 mm overall length and Ø250 mm body, is well suited to smaller turning centres where rigidity and reach are balanced. Which inserts are required for correct operation? This tool is specified for CCMT 09T3 indexable inserts; using the recommended insert geometry ensures the intended finishing performance and surface quality. What maximum bore can be machined with this tool? The tool supports a maximum cutting diameter of Ø310 mm, allowing a broad finishing range within that envelope. How does the design help reduce vibration during finishing cuts? The compact projection and robust body increase rigidity, which reduces chatter and helps achieve a consistent surface finish with the selected CCMT inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust 90° cutting configuration combined with a Ø250 mm head and secure 60 mm shank — designed for stable machining with TPKN indexable inserts; order directly via Metav Werkzeuge or consult the Metav specialists for application advice. Eckmesserkopf — corner tool head by Teknik Makina, 90° cutting angle, for TPKN 1603-2204 indexable inserts Eckmesserkopf is a compact corner tool head optimised for right-angle cutting and heavy-duty indexable insert applications, suitable for workshop and production environments where predictable chip control and straightforward insert changes are required. 90° cutting angle for consistent shoulder cuts Compatible with TPKN 2204 indexable inserts Ø250 mm head for stable machining 60 mm shank for secure clamping Reliable 90° geometry for predictable results The right-angle design provides a 90° cutting angle that simplifies set-up and guarantees reproducible shoulder and face cuts. The solid Ø250 mm head mass contributes to reduced vibration and improved surface finish during interrupted cuts, while the arrangement for TPKN 2204 inserts ensures straightforward availability of cutting edges. This geometry is especially advantageous where repeatability and short cycle times are priorities, because the design reduces rework and streamlines toolpath planning. Secure clamping and quick insert changes A substantial 60 mm shank and a precise mounting interface with E = 101.6 mm support a rigid connection to the turret or toolpost, reducing deflection under load and extending insert life. Retention is achieved with a socket-head screw M8x24, tightened with an Allen 5 key for reliable fixation. The head accepts standard TPKN indexable inserts, which allows simple rotation or replacement of cutting edges and keeps downtime to a minimum — a practical benefit in mixed-production shops. Engineered for workshop durability and serviceability With a practical overall length of 62 mm and a mass of 8.235 kg, the unit balances rigidity and compact handling for frequent tool changes. The head accommodates 9 cutting edges, offering multiple indexing options before replacement, which supports longer intervals between consumable purchases. Constructed for everyday industrial use, the design reduces the need for special fixtures and aligns with conventional toolholding systems, promoting straightforward integration and predictable maintenance cycles. Contact Metav Werkzeuge to discuss Teknik Makina corner tool heads and secure delivery from our Emmerich warehouse — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for specification matching and availability Technical data Article number: T138TM SKU: T138TM Product name: Corner tool head Compatible inserts: for TPKN 1603-2204 Indexable Inserts Brand: Teknik Makina Facts E (mm): 101.6 Shank diameter (mm): 60 Head diameter (mm): 250 Overall length (mm): 62 Weight (kg): 8.235 Cutting angle: 90° Number of cutting edges: 9 Socket-head screw: M8x24 Allen key size: 5 mm Special features Compatible with TPKN 2204 Right-angle / corner design Indexable insert system Robust construction for workshop use FAQ What inserts fit this corner tool head? The Eckmesserkopf is designed for TPKN 1603–2204 indexable inserts and accepts standard TPKN 2204 sizes for straightforward replacement and indexing. Is the shank suitable for standard turrets? Yes, the head features a 60 mm shank diameter and a defined mounting length (E = 101.6 mm) to integrate with common turret and toolpost systems used in industrial lathes and machining centres. How is the insert secured and changed? Inserts are secured on the head and clamped using the provided socket-head screw M8x24; tightening and loosening is performed with an Allen 5 key to allow quick insert indexing. Does the head support heavy interrupted cuts? The Ø250 mm head mass and rigid shank connection give improved damping and stiffness, which helps maintain stability under interrupted or heavy cutting conditions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise insert compatibility, integrated coolant delivery and stable left-hand geometry to improve cycle times and extend insert life; order the tool directly via Metav Werkzeuge or consult the team for tailored recommendations. A25S PCLNL AP350TM – PCLN Boring Bar for CNMG Indexable Inserts, Internal Coolant A25S PCLNL AP350TM is a left-hand PCLN-style boring bar designed for turning operations with CNMG 1204 indexable inserts, offering internal coolant delivery for enhanced tool life and process stability Internal coolant delivery For CNMG 1204 inserts Left-hand cutting orientation 32 mm overall diameter Coolant where it matters for longer tool life and better finishes The integrated internal coolant channel directs cutting fluid precisely to the cutter edge, reducing heat at the cutting zone and flushing swarf away from the insert seat. This focused cooling lowers thermal wear and supports a more consistent edge condition, which in turn improves surface finish and reduces rework. The result is a measurable improvement in productivity and a reduction in tooling cost per component when machining in continuous production environments. Fast set-up and reliable compatibility for efficient changeovers Built around a PCLN pocket for standard CNMG 1204 indexable inserts and identified by the A25S PCLNL ISO designation, the toolholder simplifies insert mounting and alignment. The clear interface between holder and insert shortens set-up time and minimises adjustment, supporting faster tool changes on turning centres. This compatibility ensures predictable cutting geometry and repeatable results across batches and operators. Stable geometry tuned for left-hand turning tasks The holder’s left-hand cutting orientation and robust body — 32 mm overall diameter with a 25 mm shank — create a rigid assembly that resists vibration during offset cutting. A cutting angle of 95° and a cutting height of 50 mm contribute to secure clamping of the insert and consistent chip formation. Together these features provide process stability that allows shops to maintain higher feed rates while preserving dimensional accuracy. Engineered for workshop and production use with clear supply assurance Designed for repeatable performance in commercial workshops and industrial turning lines, this boring bar balances rigidity and accessibility for frequent use. The modest mass and overall length of 250 mm provide reach without excess overhang, supporting tighter tolerances in bore and face work. For further specification details or application advice, Metav Werkzeuge’s technical consultants can assist with integration into existing toolsets and machining strategies. Contact Metav Werkzeuge for availability, technical guidance and fast supply of the A25S PCLNL AP350TM boring bar with internal coolant from Teknik Cutting Tools — direct from Emmerich to the workbench Technical data Article number: AP350TM Manufacturer: Teknik Makina Product name: A25S PCLNL Product type: PCLN boring bar for CNMG indexable inserts Data Overall length: 250 mm Diameter: 32 mm Shank diameter: 25 mm Cutting height: 50 mm Weight: 0.921 kg Cutting angle: 95° Special features PCLN for CNMG indexable inserts ISO designation A25S PCLNL Internal coolant Left-hand cutting orientation Compatible with CNMG 1204 inserts FAQ What insert type does this holder accept? The AP350TM is designed for CNMG 1204 indexable inserts and uses a PCLN-style pocket to ensure secure seating and repeatable positioning. Is the coolant internal or external? Internal coolant is provided; the internal coolant channel delivers fluid directly to the cutting edge for improved cooling and chip evacuation. Which cutting direction is this tool designed for? This boring bar has a left-hand cutting orientation, intended for left-hand turning applications. What are the key dimensions for machine setup? Key dimensions: overall length 250 mm, diameter 32 mm, shank diameter 25 mm; these figures support stability and toolholder fitting. Can the AP350TM be used on CNC lathes for production runs? Yes, the AP350TM is engineered for production use with features that support repeatable geometry, active coolant delivery and reduced set-up time Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The VT519TM extension combines a 250 mm overall length with a 25 mm shank and an M12 threaded connection to extend tooling reach while maintaining machining stability; order the extension directly from Metav Werkzeuge or consult our specialists for specification support. VT519TM Extension for Screw-in Milling Cutters — 250 mm overall length, M12 thread | Teknik Makina A robust VT519TM extension for screw-in milling cutters designed to increase reach in milling operations where a longer tool projection is required without sacrificing stability 250 mm overall length for extended reach M12 threaded connection for secure mounting 25 mm shank diameter for rigid support Greater reach without compromising rigidity The extension delivers an extended working length of 250 mm, enabling access to deep pockets and hard-to-reach contours while preserving tool stability. The 25 mm shank diameter provides a solid bearing surface in the spindle or holder, which helps to reduce vibration and runout during aggressive cuts. By combining increased length with a substantial shank cross-section, the component supports consistent machining accuracy and predictable surface finish, making it suitable for extended operations where standard holders would limit access. Secure, standardised mounting for screw-in cutters Designed for compatibility with threaded cutter systems, the extension features an M12 thread and an insertion opening of 20.7 mm, and a taper seating length of 40 mm to ensure reliable axial alignment. The internal geometry supports stable engagement of screw-in cutters: the cutter screws onto the arbor and the extension maintains concentricity, reducing the likelihood of misalignment. The straightforward threaded connection permits rapid tool changes while the conical seat improves load transfer between cutter and extension. Integrates into extended milling setups and CNC workflows The component is aimed at professional workshops and production environments that require extended tooling reach in milling or finishing tasks. The increased projection supports specialised set-ups where access constraints are a primary concern, and the solid construction contributes to predictable tool life. The extension is appropriate for both CNC machining centres and rigid manual milling machines where threaded cutter systems are already in use, allowing existing toolsets to be adapted for longer-reach applications without redesigning fixturing. Practical handling and specification guidance With a net weight of 1.165 kg, the extension has sufficient mass to damp minor vibrations while remaining manageable during handling and tool changes. The 40 mm taper length and the 20.7 mm cutter opening are key dimensions for matching with existing screw-in cutters; customers are advised to verify cutter internal diameters and manufacturer torque recommendations before assembly. For preparations involving balancing or special holders, the measured shank and thread data support planning for clamping and runout control in high-precision setups. For ordering and detailed specification assistance for this Teknik Makina extension, please contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants provide tailored advice for integrating the VT519TM into existing toolchains Technical data Article number: VT519TM Manufacturer: Teknik Makina Weight: 1.165 kg Measurements / core data Overall length: 250 mm Shank diameter: 25 mm Cutter opening (inner): 20.7 mm Taper seating length: 40 mm Design & features Thread: M12 Intended for screw-in milling cutter systems Solid, single-piece construction FAQ What is the overall length of the extension? The VT519TM extension has an overall length of 250 mm, providing extra reach for deep or obstructed machining tasks. Which thread is used for mounting? Mounting is via an M12 threaded connection, designed for secure engagement with compatible screw-in cutter systems. What shank and cutter opening diameters are specified? The extension has a 25 mm shank diameter and an internal cutter opening of 20.7 mm to receive threaded milling cutters. How long is the taper seating for the cutter? The conical seating length is 40 mm, which supports accurate axial alignment and transmission of cutting forces. Is the VT519TM suitable for CNC and manual machines? Yes; the extension is intended for integration into both CNC machining centres and rigid manual milling setups that employ screw-in cutter tooling. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 250 mm overall length, 25 mm shaft stiffness and secure M12 thread to extend screw-in milling cutters for deep or hard-to-reach cuts; this combination supports stable machining and fewer setup changes. Order the VT518TM directly via Metav Werkzeuge or consult our specialists for matching to specific applications. Extension for Screw-in Milling Cutters VT518TM — 250 mm overall length, 25 mm shaft (Teknik Makina) The Extension for Screw-in Milling Cutters offers a rigid, long-reach adapter intended for use with screw-in milling cutters in CNC machining centres and workshop milling machines, enabling access to recessed features and deeper pockets while maintaining a controlled connection to the cutting tool. 250 mm overall length for extended reach 25 mm shaft for high stiffness M12 thread for secure screw-in mounting 1.17 kg balanced mass for stable operation Greater reach with predictable machining outcomes The long adapter delivers a 250 mm overall length that extends the effective working envelope of screw-in cutters, reducing the need for additional part re-clamping or multiple setups. With a 25 mm shaft the extension preserves axial rigidity relative to smaller-diameter options, which helps to control deflection during interrupted cuts. The result is fewer programme changes and a smoother production flow when machining deep pockets or stepped components on CNC machines. Secure seating for improved concentricity and surface quality A reliable mechanical connection is the basis for reproducible results. The VT518TM uses an M12 thread and an internal seating arrangement with a 40 mm cone and a 20.7 mm opening, providing a firmly located interface between extension and cutter. This geometry reduces runout, which in turn improves surface finish and extends cutter life; in practice, correct seating and clean contact faces are decisive for minimising radial deviation during high-speed rotation. Stable dynamics and workshop durability Weighing 1.17 kg, the extension contributes mass that influences the tool system’s dynamic behaviour. That balanced mass can attenuate minor vibrations and support stable operation across a range of spindle speeds, provided the machine’s toolholding and feeds are matched accordingly. The robust dimensions favour consistent repeatability in series production, helping to keep rejects low and process times predictable. Integration into efficient supply and service workflows Sourcing the VT518TM through Metav Werkzeuge brings practical benefits for industrial and trade customers: local stock management in Emmerich, an extensive product range to reduce supplier numbers, and decades of precision expertise that support reliable procurement decisions. This combination of technical fit and dependable supply ensures workshop requirements are met with minimal administrative overhead. For tailored technical matching and prompt supply from Metav Werkzeuge, request personalised advice from our Emmerich team at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the VT518TM and its suitability for specific machining tasks. Technical Data SKU: VT518TM Manufacturer: Teknik Makina Facts Overall length: 250 mm Shaft diameter: 25 mm Shaft opening: 20.7 mm Cone length (seating): 40 mm Thread: M12 Weight: 1.17 kg Special features Extension for screw-in milling cutters Secure screw-in mounting Designed for extended-reach milling applications FAQ What sizes and interfaces does the extension use? The VT518TM from Teknik Makina features a 25 mm shaft, a 20.7 mm opening and an M12 thread, providing the defined mechanical interface for compatible screw-in milling cutters. How does the 250 mm length affect rigidity? With an overall length of 250 mm, the extension increases overhang; however, the larger shaft diameter helps to maintain stiffness, so deflection is reduced compared with thinner extensions in similar conditions. Is the VT518TM suitable for CNC machining centres? Yes. The extension is intended for use in CNC machining centres and workshop mills where screw-in cutters are employed and longer reach is required. How does the seating geometry influence runout? The 40 mm cone seating and defined opening support precise axial location, which reduces radial runout and contributes to improved surface finish and cutter life when correctly mounted. What should be considered regarding mass and dynamics? At 1.17 kg, the extension adds rotating mass that alters the tool system dynamics; spindle speed and feed should be selected with the toolholder and workpiece rigidity in mind to avoid chatter. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of ISO DSSNR 4040 format, S25 shank stability and a 45° cutting angle for consistent turning results; order directly via Metav Werkzeuge or contact our consultants for specification support. Klemmhalter DSSNR 4040 – DSSNR toolholder for SNMG indexable inserts, 45° cutting angle (Teknik Makina) A Klemmhalter DSSNR 4040 engineered as a right-hand toolholder for SNMG 2508 indexable inserts, optimised for stable external turning and facing tasks in CNC and turret lathes. DSSNR 4040 format, 45° cutting angle Compatible with SNMG 2508 inserts Robust S25 shank, 250 mm overall length 40 mm head width, 60 mm cutting height Improved cycle times through defined cutting geometry The holder’s 45° cutting angle and dedicated compatibility with SNMG 2508 indexable inserts deliver a controlled chip flow and predictable cutting forces, which together reduce cycle-to-cycle variation. In practice, this geometry supports higher feed rates under stable cutting conditions, enabling measurable productivity gains on serial turning operations. The specification for right-hand cutting ensures correct orientation in standard turret setups and eliminates ambiguity when programming tool offsets. Performance advantages are therefore tangible: improved surface finish and extended insert life derive from the combination of angle, insert seat accuracy and robust clamping. Stiffness and repeatability from shank to cutting edge Designed around an S25 shank and an overall length of 250 mm, the assembly balances accessibility with torsional rigidity. The ISO DSSNR 4040 designation guarantees standardised indexing and mounting interfaces, making the holder immediately compatible with many turret systems and changeover procedures. The holder’s measured weight of 3.012 kg and its 40 mm head width contribute to damping of vibration in interrupted cuts, resulting in consistent dimensional results. Where tight tolerances are required, the mechanical clamping layout and precise insert pocket reduce setup time and maintain repeatability across batches. Practical handling and workshop integration The toolholder accepts the widely used SNMG 2508 inserts, which simplifies inventory and reduces the variety of cutting grades in stock. The 60 mm cutting height provides a comfortable overlap with standard toolpost heights in many machines, minimising additional setup shimming. Clamping is performed with a secure screw interface compatible with the holder’s geometry, allowing swift insert replacement and straightforward inspection routines. For shops seeking a straightforward upgrade path, the holder integrates with common toolholders and requires no special adapters beyond the specified shank interface. Reliability and maintenance advantages Materials and manufacturing tolerances focus on longevity and serviceability: the ISO-compliant seating and robust shank reduce the risk of chattering and wear-induced runout. Regular inspection of the clamping screw and insert seat is recommended to maintain the initial accuracy; routine checks will preserve the holder’s performance and extend component life. The product’s construction supports a maintenance-first approach that keeps machines productive and reduces unexpected downtime, aligning with lean manufacturing objectives. For specification advice or to secure this Teknik Cutting Tools DSSNR holder for SNMG 2508 inserts, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to discuss integration and availability. Technical data Article number: D208TM Manufacturer: Teknik Makina Designation: Klemmhalter DSSNR for SNMG indexable inserts ISO designation: DSSNR 4040 Facts Overall length: 250 mm Shank type: S25 Holder width: 50 mm Head width: 40 mm Cutting head width: 40 mm Cutting height: 60 mm Weight: 3.012 kg Cutting angle: 45° Cutting direction: right Special features Compatible with SNMG 2508 indexable inserts Right-hand turning toolholder ISO-compliant insert pocket Robust clamping interface for stable cutting Suitable for turret and CNC lathe installations FAQ Which inserts fit this holder? The Klemmhalter DSSNR 4040 is designed for SNMG 2508 indexable inserts and seats them in an ISO-compliant pocket for reliable seating and repeatable cutting geometry. Is the holder suitable for standard turret turrets? Yes, the S25 shank and the ISO DSSNR 4040 format make the holder compatible with common turret and toolpost systems used in industrial lathes. What is the cutting direction and angle? This toolholder is specified for right-hand cutting with a 45° cutting angle, offering controlled chip formation and improved surface finish in typical turning applications. How does the holder affect insert life? By providing a stable clamping interface and precise seat alignment, the holder helps to reduce insert wear and can contribute to longer effective tool life under comparable cutting conditions. What is the overall length and how does it influence stiffness? The 250 mm overall length balances reach and rigidity; shorter setups will increase stiffness, while the specified length allows access to workpiece features without excessive deflection. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise 90° shoulder milling combined with a robust 25 mm shank and 45 mm cutting length for consistent tool life and stable machining. The design for APKT 1604 indexable inserts reduces downtime through quick insert changes. Order the cutter directly via Metav Werkzeuge or contact our consultants for specification advice. S256TM Shaft Cutter — Indexable milling cutter for APKT 1604, 25 mm shank (Teknik Makina) S256TM is a 90° indexable milling cutter intended for robust shoulder and face milling operations with APKT 1604 inserts 90° cutting angle for square shoulders 25 mm shank for stable clamping Compatible with Korloy APKT 1604 inserts Torx M4x10 screw, T15 interface Accuracy and rigidity for repeatable shoulder milling The 90° geometry delivers consistently square shoulders and predictable tool engagement, which helps to maintain part tolerances in batch production. The combination of a 25 mm shank and an overall length of 120 mm improves axial rigidity and reduces chatter when compared with slender tooling. Where tight geometry is required, the 45 mm cutting length provides adequate reach without unnecessary overhang, assisting in maintaining surface finish and dimensional stability. These characteristics translate directly into fewer reworks and more reliable cycle times on production runs. Quick insert changes and secure clamping to reduce downtime Designed for indexable inserts, the cutter accepts APKT 1604 plates and secures them with a Torx M4x10 screw accessed via a T15 key interface. The use of indexable tooling means the cutting edge can be renewed rapidly by replacing the insert rather than the entire tool body, lowering tooling costs over time. With two cutting edges per insert, the system supports efficient use of insert geometry and enables straightforward rotation or replacement, contributing to higher machine uptime and simpler maintenance routines. The S256TM construction focuses on reliable clamping and repeatable seating of the insert pocket. Predictable throughput and simplified tool management Indexable systems like this cutter promote predictable total cost of ownership: indexable inserts concentrate the wearing element into small, replaceable parts while the tool body remains a long-term asset. For operations that favour batch processing or mixed-series production, the ability to standardise on APKT 1604 inserts simplifies inventory and reorder processes. The cutter’s balanced dimensions and specified geometry make it suitable for general industrial milling tasks where a 90° cutting angle is required; the result is sustained productivity with reduced planning complexity and straightforward tool change procedures. Supply reliability and partner expertise from Metav Procured through Metav Werkzeuge, this cutter benefits from a supplier positioned as a “quality filter” for the European market. Metav combines decades of precision competence with broad product availability, supporting workshops and manufacturing with a large catalogue and dependable logistics. The established customer base and comprehensive assortment reduce procurement risk and help centralise tooling needs. For purchasers seeking consistent supply and technical guidance, Metav’s expertise complements the cutter’s technical strengths and supports seamless integration into existing toolsets. Choose Teknik Makina’s S256TM for reliable 90° milling and contact Metav Werkzeuge for tailored technical advice and supply via info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical Data Article number: S256TM Manufacturer: Teknik Cutting Tools Suitable for inserts: APKT 1604 Compatible insert manufacturer: Korloy Shank diameter: 25 mm Cutting length: 45 mm Cutting angle: 90° Number of cutting edges: 2 Overall length: 120 mm Weight: 0.43 kg Torx screw: M4x10 (T15) Core Data Shank diameter: 25 mm Cutting length: 45 mm Overall length: 120 mm Weight: 0.43 kg Cutting angle: 90° Cutting edges: 2 Special features For APKT 1604 indexable inserts Compatible with Korloy inserts Torx M4x10 screw, T15 interface SKU: S256TM Brand: Teknik Makina FAQ What inserts fit this cutter? The cutter is designed for APKT 1604 indexable inserts and is compatible with Korloy plates shaped to that designation. How is the insert secured in the cutter? Inserts are held by a Torx screw (M4x10) using a T15 key; the fastening system is designed for repeatable seating and reliable clamping. Is the S256TM suitable for shoulder milling? Yes — the 90° cutting angle makes the S256TM particularly suitable for square shoulder and face milling operations with predictable geometry. How many cutting edges are used per insert? Each insert provides two cutting edges, enabling rotation or replacement to extend usable life before disposal. Where can replacement inserts or spares be sourced? Replacement APKT 1604 inserts from Korloy and spare fastening screws can be supplied through Metav Werkzeuge as part of routine replenishment. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com