Gibt es einen Hahn und Kolb Online Shop?

Take advantage of a compact cutter body that combines internal coolant and a 22 mm diameter for improved chip control and stable machining. The combination of a 20 mm shank, 30 mm cutting length and three cutting edges ensures balanced material removal and reliable tool life — order or request guidance from Metav Werkzeuge for application advice. 22 mm milling cutter S146-1TM — cutter body for APKT 1003 indexable inserts, internal coolant (Teknik Makina) 22 mm milling cutter S146-1TM designed as a robust cutter body for APKT 1003 indexable inserts, equipped with internal coolant to support efficient chip evacuation and consistent surface results in serial and job-shop milling Internal coolant for improved chip control 22 mm diameter for compact machining Compatible with APKT 1003 Korloy inserts 3 cutting edges for balanced removal Higher material removal rates with consistent stability The cutter body is engineered to deliver stable cutting performance through its three-flute geometry and stout 20 mm shank, which reduces vibration and improves run-out behaviour. The combination of a 22 mm body diameter and 30 mm cutting length enables secure engagement in shoulder and light face milling operations. For production environments where cycle time and repeatability matter, the internal coolant feed is routed to the cutting zone to assist chip evacuation and reduce heat at the cutting edge, which supports longer insert life and fewer process interruptions. Compatibility and secure clamping for reduced setup times The tool is supplied for use with APKT 1003 indexable inserts and is matched to industry-standard clamping hardware, including the specified Torx T8 key and M2.5x5.5 Torx screw. This configuration ensures fast insert changes and repeatable seat seating, so the cutting edge is positioned reliably after each index. Using standardised inserts from Korloy simplifies inventory and enables straightforward selection of grades for steel, aluminium or mixed materials where indexable insert strategies are preferred. Practical serviceability and workshop integration The design of the S146-1TM milling cutter supports efficient maintenance and replacement routines: the accessible Torx drive facilitates quick insert fastening, while the internal coolant connection is compatible with typical machine coolant supplies. The tool’s modest mass and compact overall dimensions (100 mm total length) make it suitable for both mobile setups and fixed-production fixtures. Technicians will appreciate that common workshop tools suffice for routine interventions, reducing downtime and keeping throughput steady. Contact Metav Werkzeuge for tailored application advice and secure supply of the Teknik Makina S146-1TM milling cutter with internal coolant and APKT 1003 compatibility Technical Data Article number: S146-1TM Label: 22mm Schaftfräser APKT 1003 L100mm mit Innenkühlung Manufacturer: Teknik Makina Product type: Milling cutter Facts Diameter: 22 mm Total length: 100 mm Shank diameter: 20 mm Cutting length: 30 mm Number of cutting edges: 3 Weight: 0.243 kg Special features Internal coolant Compatible with APKT 1003 inserts (Korloy) Torx key: T8 Torx screw: M2.5x5.5 Designed for indexable insert clamping FAQ Which indexable inserts fit this cutter body? The cutter body accepts APKT 1003 indexable inserts; the S146-1TM is supplied to work with Korloy-manufactured inserts for standardised seating and repeatable geometry. Is the coolant supplied through the tool body? Yes, the S146-1TM features internal coolant directed to the insert area to assist chip evacuation and temperature control during milling. What clamping hardware is required for insert changes? Insert fastening uses an M2.5x5.5 Torx screw driven by a T8 key, allowing quick and secure insert replacement on the S146-1TM cutter body. Does the tool require a special holder or is the shank standard? The tool has a 20 mm shank suitable for standard collet or holder systems that accept a 20 mm diameter shank, enabling easy integration into existing tool setups. For which machining tasks is this cutter particularly suitable? With a 22 mm diameter, 30 mm cutting length and three cutting edges, the S146-1TM is well suited to medium-duty slotting, shoulder milling and light face milling where indexable insert economics are desired. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precision, internal coolant and broad insert compatibility for reliable, high-throughput milling. Order the cutter body directly via Metav Werkzeuge or ask the consultants for machining recommendations. Shank cutter — indexable end mill body with internal coolant, 22 mm diameter (Teknik Makina) A shank cutter designed as an indexable end mill body for APKT 1003 indexable inserts, suitable for machining operations where stiffness and coolant delivery to the cutting zone are essential. 22 mm cutter diameter Internal coolant supply Compatible with APKT 1003 inserts (Korloy) 20 mm shank, 60 mm cutting length Stable cutting performance for consistent surface quality The tool body delivers rigidity through its 22 mm diameter and 20 mm shank, reducing chatter and improving surface finish on a variety of workpieces. With three cutting edges, the design balances material removal rate and stability: a modest number of edges lowers cutting forces per tooth while maintaining a steady metal removal rate. For shops migrating from solid end mills to indexable systems, the holder body provides a predictable cutting behaviour and allows the use of standard APKT 1003 inserts for cost-efficient edge replacement. Coolant-through design reduces heat and improves tool life A controlled internal coolant channel feeds coolant directly to the insert seat, enhancing chip evacuation and reducing thermal load at the cutting edge. The direct coolant supply supports higher cutting parameters without compromising tool life, particularly in interrupted cuts or deeper pocketing. Maintenance is straightforward: insert clamping uses a Torx T8 driver and M2.5x5.5 screw, enabling quick index changes and minimal downtime during shift changes. Versatile compatibility and simple integration into production Compatibility with Korloy-manufactured APKT 1003 inserts makes the holder an economical choice for workshops standardising on carbide grades and geometries. The cutter’s total length of 150 mm and 60 mm effective cutting length fit common tool setups, and the modest weight of 0.36 kg keeps balance considerations simple for spindle-speed adjustments. Using an indexable holder reduces inventory of full-profile cutters while retaining flexibility for finishing or roughing by selecting suitable inserts. Contact Metav Werkzeuge for tailored advice on integrating the Teknik Makina indexable end mill body with internal coolant into existing processes, and request verification for specific machine-spindle and workpiece combinations Technical data SKU: S178-1TM Manufacturer: Teknik Cutting Tools Label: 22mm Shank cutter APKT 1003 L150mm with internal coolant Facts Cutter diameter: 22 mm Total length: 150 mm Shank diameter: 20 mm Cutting length: 60 mm Number of cutting edges: 3 Weight: 0.36 kg Special features Internal coolant Compatible with APKT 1003 indexable inserts Suitable insert manufacturer: Korloy Torx key: T8 Torx screw: M2.5x5.5 FAQ How does internal coolant improve milling with this holder? Internal coolant supplies cutting fluid directly to the insert seat, improving chip evacuation and cooling the cutting edge, which can increase achievable cutting speeds and extend tool life for the Teknik Makina indexable end mill body. Which inserts fit this cutter body? This holder is designed for APKT 1003 indexable inserts and is compatible with inserts produced by Korloy, allowing straightforward procurement and interchangeability. Can the holder be used for finishing operations? Yes. With the correct choice of insert geometry and grade, the holder supports finishing passes thanks to its rigidity and coolant-assisted heat control. What tool is needed to change inserts? Insert clamping uses a Torx T8 driver and an M2.5x5.5 screw for secure fixation and rapid index changes. Is the shank size suitable for standard toolholders? The 20 mm shank matches common toolholders and collets designed for that nominal shank diameter; compatibility should be confirmed against the specific clamping system. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the rigid 20 mm shank, a 22 mm cutting diameter and compatibility with APXT 1003 indexable inserts for reliable, high‑repeatability milling — order directly via Metav Werkzeuge or consult our technical advisers for application support. Shank Milling Cutter S168TM — 22 mm diameter, 3‑edge, for APXT 1003 indexable inserts (Teknik Makina) The Shank Milling Cutter S168TM is an insert milling cutter designed for industrial milling tasks, offering rigid toolholding and economical indexable insert use in production and jobbing shops 22 mm cutting diameter Three cutting edges for stable cuts 20 mm shank for rigid toolholding Compatible with APXT 1003 inserts High stability for tight tolerances and long tool life The combination of a 20 mm shank and three‑flute geometry gives notably improved stiffness compared with smaller shank tools. This design reduces tool deflection under load, which results in consistent part accuracy and extended insert life. In practice, the stiffer mounting allows machining at higher feed rates with fewer passes, so cycle times are reduced while surface quality remains stable. The specification is especially suitable for milling operations where repeatability and dimensional control are essential. Fast insert changes and secure clamping for uptime Clamping is performed using a Torx M2.5 x 5.5 screw tightened with a T8 key, providing positive and repeatable insert retention. Compatibility with APXT 1003 indexable inserts — including those from Korloy — means replacements are inexpensive and quick to fit, reducing downtime. The indexable system separates cutting edge wear from the tool body, lowering long‑term tooling costs and simplifying inventory: a small set of inserts maintains multiple cutters across the shop floor. Geometry optimised for mixed finishing and light roughing A 90° cutting angle and three cutting edges deliver a balance between material removal rate and surface finish. With a cutting length of 40 mm and overall length of 120 mm, the cutter is engineered for accessible reach without compromising rigidity. The flute arrangement moderates chip formation, improving evacuation and lowering the risk of re-cutting swarf. For users seeking a predictable finish and repeatable cycle times, this geometry supports efficient throughput on a wide range of operations. Practical workshop benefits and application scope Beyond geometry, the tool’s modest weight (0.29 kg) and standard interfacing make it straightforward to fit into existing tool holders and machining setups. The cutter is aimed at production and maintenance engineers looking for a cost‑effective indexable solution that integrates with standard insert systems. Where flexibility is required — quick edge changes, repeatable clamping and consistent runout control — this tool provides a straightforward upgrade to productivity without complex retooling. For robust indexable milling with APXT 1003 inserts, contact Metav Werkzeuge for procurement and tailored technical advice: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data SKU: S168TM Manufacturer: Teknik Makina Product: Shank milling cutter for APXT 1003 indexable inserts Compatible inserts: APXT 1003 (Korloy) Torx screw: M2.5 x 5.5 Torx key: T8 Core specifications Diameter: 22 mm Shank diameter: 20 mm Cutting length: 40 mm Number of cutting edges: 3 Overall length: 120 mm Cutting angle: 90° Weight: 0.29 kg Features & compatibility Compatible with Korloy inserts For APXT 1003 indexable inserts Three‑flute geometry for stable cutting Torx clamping screw for secure insert fixation FAQ Which inserts fit this milling cutter? The cutter accepts APXT 1003 indexable inserts; compatibility with Korloy inserts is specified for the milling cutter S168TM from Teknik Makina. What shank and holder dimensions are required? The tool features a 20 mm shank diameter; a matching rigid toolholder with 20 mm bore is recommended for optimal performance. How many cutting edges does the tool have and what is the benefit? The tool has three cutting edges, which provide a compromise between smooth chip load distribution and sufficient material removal rate for stable cutting. What torque key is needed for insert clamping? Insert clamping uses a Torx screw M2.5 x 5.5, tightened with a T8 key for secure and repeatable fixation. For which operations is this cutter best suited? With a 22 mm diameter and 40 mm cutting length, the cutter is aimed at mixed finishing and light roughing where rigidity and quick insert changes are priorities. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining compact dimensions with a secure M6 clamping screw and a 5 mm tool bore, this mini parting clamp holder delivers stable fixation in tight lathe setups; its 22 mm body and 88 mm overall length simplify integration into narrow toolposts. Order the holder via Metav Werkzeuge or consult our specialists for application advice. Mini parting clamp holder DC328TM by Teknik Makina — 22 mm body, M6 clamping screw A compact Mini parting clamp holder designed for secure clamping of parting and profiling tools in confined lathe operations. Compact 22 mm body for tight toolposts M6 clamping screw for secure fixation 88 mm overall length for confined setups Lightweight at 0.274 kg for easy handling Stable clamping for precise parting cuts The holder provides a rigid clamping arrangement that reduces vibration during parting operations. With a dedicated M6 clamping screw and a centred 5 mm tool bore, the design ensures consistent contact pressure and predictable tool behaviour. Reduced micro-movement leads to more repeatable part-off faces and fewer rework cycles. The construction is aimed at users seeking reliable performance when working with slender parting blades or profiling inserts in small to medium lathes. Compact footprint for cramped toolposts and tight centres A small toolholder body with a 22 mm diameter and 88 mm overall length allows installation where larger holders will not fit. The compact geometry supports installations close to chuck faces and in multi-tool turrets, reducing overhang and improving rigidity. Shorter overhangs directly influence deflection and surface finish, so the compact format supports higher cutting stability and easier setup in confined workspaces, contributing to time savings during tool changes. Simple integration, lightweight handling and workshop efficiency Weighing just 0.274 kg, the holder is easy to handle during setup and changeover, reducing strain during repetitive operations. The straightforward clamp interface is compatible with common parting blades and is designed for quick alignment. By combining compact dimensions with a conventional clamping thread, the product streamlines retrofitting into existing toolposts without complex adapters. Specification clarity and predictable mounting characteristics result in shorter downtime and improved process reliability. Contact Metav Werkzeuge in Emmerich for bespoke advice on the Teknik Makina Mini parting clamp holder DC328TM — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss fitment and workshop applications Technical data Article number: DC328TM Manufacturer: Teknik Makina Product name: Mini parting clamp holder Dimensions / weight Diameter: 22 mm Overall length: 88 mm Shank bore: 5 mm Thread: M6 Weight: 0.274 kg Features Compact toolholder design Intended for parting/turning toolholding Lightweight, easy to change FAQ What shank size does the holder accept? The holder accepts a 5 mm tool shank; this is shown by the specified 5 mm shank bore for the Teknik Makina mini parting clamp holder (SKU DC328TM). What are the key dimensions for installation? The body diameter is 22 mm and the overall length is 88 mm, providing a compact footprint suitable for narrow toolposts and confined lathe setups. Which thread is used for the clamping screw? Clamping is secured via an M6 thread, providing standardised fixation compatible with common clamping screws. Is the holder suitable for frequent tool changes? Yes; at 0.274 kg the holder is lightweight and designed for straightforward handling and quick changeovers in production or workshop environments. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the compact 22 mm shank and short L88 mm overall length to improve rigidity and access in confined turning operations; the combination of compact design and reliable clamping contributes to steadier cuts and fewer set-ups. Order the Mini parting toolholder directly via Metav Werkzeuge or consult our technical team for application advice. Mini parting toolholder D22 d10 L88 by Teknik Makina — compact 22 mm shank, 88 mm overall length The Mini parting toolholder D22 d10 L88 is a compact clamping solution for precision parting and grooving on lathes, designed for tight setups and improved tool rigidity 22 mm shank diameter Compact L88 overall length Stable clamping for parting tasks Reduced overhang for improved accuracy Improved stability and access for tight turning operations The compact 22 mm shank combined with an L88 overall length reduces tool overhang, which improves stiffness and diminishes chatter during parting operations. For workshops facing limited clearance, this short footprint provides better access to confined work zones while maintaining a secure clamp. The design focuses on mechanical stability rather than added complexity, so the result is a simpler tool arrangement that supports consistent cut quality and predictable tool life. Streamlined workshop use and inventory management With a concise form factor and clearly defined dimensions, the DC354TM simplifies tool planning and storage. The small toolholder helps to reduce machine set‑up time by offering predictable positioning and repeatable clamping characteristics, which supports faster changeovers and steadier process control. The compact design also assists in standardising tooling kits for small‑batch production or multi‑operation turning cells, improving overall shopfloor efficiency. Trusted supply and practical support through Metav Sourced from Teknik Makina, this mini clamping solution benefits from reliable manufacturing and practical application focus. Purchasing via Metav provides the added value of a European quality filter and dependable logistics from Emmerich, backed by decades of metrology and tooling experience. The partnership ensures consistent availability and a professional procurement route for workshops and industrial buyers seeking compact, performance‑oriented clamping tools. Discuss the DC354TM with Metav Werkzeuge for tailored procurement and technical advice from our Emmerich team, ensuring the right mini parting toolholder for your lathe setups. Technical Data SKU: DC354TM Label: 22mm Mini-Stechklemmhalter L88mm Name: Mini parting toolholder D22 d10 L88 Manufacturer: Teknik Makina Facts Diameter: 22 mm Overall length: 88 mm ECLASS: 21181005 UID: DC354TM Special features Mini design for confined spaces Clamping function for parting/grooving Short overhang for improved rigidity FAQ What is the shank diameter of this toolholder? The shank diameter is 22 mm, as specified for the DC354TM mini toolholder. What is the overall length of the holder? The overall length is 88 mm, giving a compact L88 footprint for tight setups. Which applications is the holder intended for? The holder is intended for parting and grooving operations on lathes, offering a compact clamping solution for these turning tasks. Who manufactures this mini parting toolholder? The toolholder is produced by Teknik Makina and is available under the SKU DC354TM. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The compact design and short overhang of this tool deliver steady clamping and improved accessibility in confined turning setups. With a 22 mm shank and 88 mm overall length, the holder reduces vibration and supports accurate grooving cycles. Order the component directly via Metav Werkzeuge or request advice from their consultants for fast integration into production. Mini grooving clamp holder D22 d06 L88 (Teknik Makina) The mini grooving clamp holder provides compact, precise clamping for grooving and parting operations on lathes and CNC turning centres. Compact grooving holder, ideal for tight toolpaths 22 mm shank diameter for slim tool posts 88 mm overall length to reduce overhang SKU DC336TM by Teknik Makina Precision clamping in confined toolrooms The compact grooving clamp holder concentrates stiffness where it matters. Thanks to the 22 mm shank and an 88 mm overall length, the design reduces cantilever effects and lateral vibration during narrow-groove cuts. This results in improved surface finishes and longer insert life compared with oversized holders. For shops handling small-diameter workpieces, the reduced profile facilitates close-positioned tooling and safer turret clearance. Faster set-up and consistent process outcomes A short, predictable tool geometry simplifies tool offsets and repeatable set-up. The holder’s compact form supports rapid indexing and consistent radial engagement with the insert—key factors for repeatable grooving cycles. With the DC336TM label for quick identification, toolroom organisation is simplified and changeover times are lowered, supporting leaner machining sequences and higher spindle utilisation. Integration into standard turning workflows Designed for conventional and CNC lathes, the small form factor allows installation on slim tool posts and low-profile tool blocks. The item is optimised for grooving and parting applications where minimal overhang is required; the reduced mass near the cutting edge benefits high-precision turning tasks. The straightforward geometry also eases measurement and inspection steps during process validation. Practical benefits for workshops and production lines Adopting a compact grooving clamp holder helps protect inserts and reduces scrap rates by stabilising the cutting zone. The holder’s labelled SKU and concise dimensions support predictable tool lists and faster procurement. For maintenance cycles and inventory management, the clear designation and compact footprint make storage and rotation simpler in both small workshops and larger production environments. Contact Metav Werkzeuge in Emmerich for tailored advice on integrating the Teknik Makina DC336TM into existing turning setups and to secure reliable supply from our European warehouse Technical Data SKU: DC336TM Product: Mini grooving clamp holder Manufacturer: Teknik Makina Eclass: 21181005 Dimensions & Core Data Shank diameter: 22 mm Overall length: 88 mm Designation: D22 d06 L88 Labels & Identification Short label: 22mm Mini-Stechklemmhalter L88mm Product type: Mini-Stechklemmhalter FAQ Which machines is this holder compatible with? The holder is suitable for conventional lathes and CNC turning centres that accommodate a 22 mm shank; the Teknik Makina DC336TM is intended for low-profile tool posts and compact turret stations. What are the exact shank and length dimensions? Shank diameter is 22 mm and overall length is 88 mm for the DC336TM mini grooving clamp holder, matching slim toolpost configurations. Which turning tasks are best suited to this holder? The design is aimed at grooving and parting operations where reduced overhang and stable clamping improve surface finish and insert life. How does the compact profile benefit workshop efficiency? A shorter overhang reduces vibration and improves repeatability, which lowers scrap rates and shortens set-up and changeover times in batch and single-piece production. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of a metric M6 thread, a compact 9.5 mm diameter and a 22 mm total length ensures secure clamping with minimal axial play; ideal for high-repeatability milling setups. Order the screw directly via Metav Werkzeuge or consult our team for application-specific guidance. Screw for End Mill TC181TM — M6 thread, 9.5 mm diameter (Teknik Makina) The Screw for End Mill TC181TM is a retention fastener designed to secure end mill shanks in milling holders and adaptors, providing stable clamping for precision cuts. M6 standard thread for secure clamping Diameter 9.5 mm for tight fit Total length 22 mm for compact assemblies Hex key 3 mm compatible with Allen wrench Secure clamping that improves tool stability and repeatability A compact retention screw such as this is a straightforward way to reduce axial and radial movement in the toolholder. With a metric M6 thread and a 9.5 mm diameter, the fastener creates consistent contact pressure across the clamping interface, which reduces runout and enhances concentricity during milling. The result is fewer rework cycles and more predictable tool life, translating directly into improved process efficiency for production and repair workshops. Quick serviceability for reduced downtime Maintenance cycles benefit from a simple design that is compatible with a 3 mm Allen key, enabling fast replacement or retightening at the bench or on the machine. The 22 mm total length keeps the assembly compact while allowing enough engagement for reliable fixation, so changeovers are completed swiftly without special tooling. This eases everyday workshop routines and supports higher machine availability — a practical advantage for busy job shops and production lines. Designed for integration with standard holders and workshop logistics Manufactured to fit conventional end mill shank arrangements, the component follows familiar metric conventions making it straightforward to match with existing holders and adaptors. The screw’s lightweight nature and standard geometry simplify inventory management and spare-part planning. Combined with Metav Werkzeuge’s sourcing and quality-filtering from Emmerich, procurement becomes more dependable, helping to centralise supplies and support a smoother workflow across industry, craft and trade operations. For tailored advice on matching this Teknik Makina retention screw to specific holders or to secure appropriate spares, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: TC181TM Name: Screw for End Mill Manufacturer: Teknik Makina Weight: 0.1 kg Facts Diameter: 9.5 mm Thread: M6 Total length: 22 mm Weight: 0.1 kg Special features Compatible with 3 mm Allen key Suited for end mill shanks Metric M6 thread standard FAQ Is this screw compatible with standard end mill holders? The TC181TM screw is intended for use with holders that accept a metric M6 thread and a 9.5 mm clamping interface; verification of the holder thread and bore is recommended before installation. Which tool is required to tighten the fastener? A 3 mm Allen key (hex key) is specified for the retention screw, allowing straightforward tightening and removal at the machine or workshop bench. How often should the screw be inspected or replaced? Inspect the screw periodically for thread wear, deformation or corrosion; replacement is advised when secure clamping can no longer be achieved to maintain the integrity of the clamping system. What is the SKU and who manufactures this component? The SKU is TC181TM; the part is supplied by Teknik Makina and intended as a retention screw for end mill assemblies. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine solid shank stability with reliable indexable‑insert compatibility — the result is consistent finishing and fast insert changes; order the tool directly via Metav Werkzeuge or contact the consultants for application support. Teknik Makina S116TM Shaft milling cutter — 22 mm diameter, indexable inserts compatible The Shaft milling cutter S116TM is a shank-mounted milling solution for precision face and slot operations using TPKN 1103–2204 indexable inserts on CNC and manual machines. Compatible with TPKN 1103–2204 inserts 22 mm cutting diameter 20 mm shank for stable clamping Two cutting edges for smooth finishing Reliable compatibility for indexable-insert machining The design centres on proven insert compatibility with TPKN 1103 and TPKN 2204 grades, enabling toolshops to use a widely available insert family for a variety of finishing tasks. Using indexable inserts means that only the small cutting tip is renewed when worn, which reduces downtime and keeps inventory simple. The 22 mm cutting diameter and the two‑edge configuration provide a balance between material removal and surface quality, while the fixed insert pocket and clamping arrangement ensure repeatable positioning for every index. Stability and predictable performance in daily use A 20 mm shank and an overall length of 120 mm deliver rigid support in standard toolholders, lowering vibration and improving surface finish compared with slender alternatives. The cutter’s 45 mm cutting length offers sufficient engagement for shallow face milling or light slotting, and the modest mass (approx. 0.301 kg) assists in spindle balance and acceleration. Insert clamping is achieved with an M6x14 Torx screw secured with the supplied 3 Allen key, giving a straightforward and reproducible assembly that supports consistent cycle times on production batches. Quick setup and maintenance for workshop efficiency The indexable system simplifies changeovers: worn inserts are removed and indexed or replaced without removing the holder from the spindle in many setups, reducing machine downtime. The robust clamping screw and accessible pocket geometry make insert changes efficient and safe, which is particularly valuable in small to medium production runs where uptime is a priority. Clear labelling of the tool and standard dimensions assist in inventory management and make the shaft cutter easy to integrate into established tooling sets. Practical applications and operational benefits This shank cutter is suited to finishing passes, face milling and light slotting where repeatable geometry and surface quality matter. Compatibility with the TPKN insert family permits selection of grades and geometries optimised for the workpiece material and machining strategy; toolroom staff can therefore adapt cutting edge grade without changing the holder. The combination of stable clamping, a standardised 22 mm diameter and simple insert access supports reliable results across batch production and bespoke machining tasks. For supply, compatibility checks or to discuss tooling strategies for Teknik Makina cutting solutions contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — the team will advise on the S116TM and suitable insert grades. Technical data Article number: S116TM Manufacturer: Teknik Makina Designation: Shaft milling cutter for TPKN 1103-2204 indexable inserts eClass: 21180806 ETIM: EC011860 Dimensions & weights Cutting diameter: 22 mm Shank diameter: 20 mm Cutting length: 45 mm Overall length: 120 mm Number of cutting edges: 2 Weight: 0.301 kg Features & compatibility Compatible inserts: TPKN 1103 / 2204 Torx screw: M6x14 Torx key: 3 Allen SKU: S116TM Files available: 2 attachments FAQ Which insert types fit this cutter? The cutter accepts TPKN 1103 and TPKN 2204 indexable inserts; insert grade selection determines material suitability and cutting strategy. What are the key dimensions to check for toolholding? Check the 20 mm shank and 120 mm overall length to ensure compatibility with the selected chuck or holder and sufficient projection for the intended cut. How many cutting edges does the tool have? This shaft milling cutter is supplied with two cutting edges, providing a compromise between surface finish and material removal rate. How is the insert fixed in place? Insert retention is via an M6x14 Torx screw, tightened with the supplied 3 Allen key for reproducible clamping. What applications suit this shank milling cutter? Typical uses are finishing passes, face milling and light slotting where indexable inserts and quick tip changes are valued. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of reliable compatibility with APXT 1003 indexable inserts and a rigid Ø22 mm cutting diameter ensures efficient, reproducible milling results; the compact 100 mm overall length and secure Torx fixing make the tool well suited for standard CNC operations. Order via Metav Werkzeuge for assured supply or consult the technical team for application advice. Shank Cutter S146TM — for APXT 1003 Indexable Inserts, Ø22 mm, 3 Cutting Edges (Teknik Makina) A Shank Cutter S146TM engineered for milling with APXT 1003 indexable inserts, combining a 22 mm cutting diameter and a 90° cutting angle for consistent face and slot milling. Compatible with APXT 1003 indexable inserts Ø22 mm cutting diameter 3 cutting edges for stable machining M2.5x5.5 Torx screw and T8 key High-performance machining through proven insert compatibility The S146TM is designed around the APXT 1003 insert system, offering the economic advantage of replaceable cutting edges and predictable performance. By accepting Korloy inserts, the tool allows rapid return to cutting after an insert change, reducing machine downtime. The arrangement of 3 cutting edges distributes cutting forces evenly, which helps to maintain a smooth chip flow and steady spindle load. For production environments prioritising throughput, this configuration supports repeatable results and lowers per-part tooling costs. Rigidity and set-up precision for stable results A 20 mm shank provides the necessary stiffness for many CNC milling setups, while the 30 mm cutting length balances reach with rigidity. The precise shank diameter and overall 100 mm length contribute to predictable deflection characteristics during cutting, improving dimensional stability. The cutter is fastened using an M2.5x5.5 Torx screw (T8), enabling secure clamping of the insert and simple servicing with commonly available torque tools. These features translate into fewer interruptions for rework and a shorter machine setup time. Practical advantages in workshop workflows Selecting a shank cutter that matches a widely used insert type helps streamline inventory; stocking the S146TM means fewer complete cutters are required when inserts are renewed. The Ø22 mm cutting diameter is suited to a range of face and light slotting operations where APXT 1003 inserts are specified. The tool’s modest weight (0.243 kg) and standard fixing method make handling and replacement straightforward on machine trolleys and in production cells, promoting a cleaner changeover process and safer tool handling routines. Maintenance and serviceability that keep production moving Service tasks are reduced to a quick insert replacement and a single Torx screw operation, with the T8 key commonly available across maintenance toolsets. The straightforward construction simplifies inspection and reduces the time needed for tool checks between shifts. Keeping a small stock of APXT 1003 inserts and M2.5x5.5 screws ensures minimal downtime; the modular nature of indexable systems helps to preserve cutter bodies while delivering consistent cutting performance over many insert cycles. For reliable supply and practical advice on using the Teknik Cutting Tools S146TM shank cutter, contact Metav Werkzeuge GmbH in Emmerich by e‑mail at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 for tailored recommendations and fast delivery. Technical Data Article number: S146TM Manufacturer: Teknik Makina Product: Shank cutter for APXT 1003 indexable inserts SKU: S146TM Facts Cutting diameter: 22 mm Shank diameter: 20 mm Cutting length: 30 mm Overall length: 100 mm Number of cutting edges: 3 Cutting angle: 90° Weight: 0.243 kg Torx screw: M2.5x5.5 Torx key size: T8 Special features Compatible with APXT 1003 indexable inserts Suitable for Korloy insert variants Secure Torx fixing for quick insert changes Compact shank design for standard CNC toolholders FAQ Which inserts are compatible with this cutter? The S146TM is designed for APXT 1003 indexable inserts and is compatible with Korloy-manufactured inserts in that size and seat form. What are the key dimensions to check when mounting the shank cutter? Check the 20 mm shank diameter, the Ø22 mm cutting diameter, and the overall 100 mm length to ensure correct clamping and adequate clearance in the machine setup. How is the insert secured in the S146TM? The insert is fastened with an M2.5x5.5 Torx screw, tightened using a T8 key for consistent clamping force and easy replacement. Is the S146TM suitable for heavy roughing operations? The S146TM is optimised for stable, repeatable milling with APXT 1003 inserts; for heavy roughing, consider cutter and insert combinations specified for higher cutting forces and larger insert geometries. Can the cutter body be reused after multiple insert changes? Yes. The indexable system of the S146TM is intended to allow repeated insert replacement while retaining the cutter body, offering cost efficiency across multiple insert cycles. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, robust drill body that combines precise clamping with easy insert replacement; the compatibility with Taegutec SOMT 0703 inserts reduces tooling costs and downtime while the Ø 22 mm diameter and 25 mm shank ensure stable results in series production — order via Metav Werkzeuge or ask for tailored advice. Indexable Insert Drill U418TM — Drill body, Ø 22 mm, 25 mm shank (Teknik Makina) The Indexable Insert Drill U418TM is a drill body engineered for insert-based drilling operations in machining centres and drilling heads, combining a short, rigid design with standard insert compatibility. Compact design with 25 mm shank Compatible with Taegutec SOMT 0703 inserts 88 mm effective cutting length Rigid body for reduced vibration Stable clamping delivers consistent hole quality The drill body is built around a 25 mm shank and a Ø 22 mm cutting diameter to provide a secure, machine-friendly connection that reduces run-out and vibration. This rigidity translates into consistent hole quality across production runs and fewer rejects; the standardised shank diameter also simplifies toolholder selection and repeatable set-up routines, supporting predictable cycle times and reduced rework. Reduced tooling expense through insert standardisation Designed for indexable cutters, the tool accepts Taegutec SOMT 0703 inserts which are widely available and simple to replace. Using standard insert geometry means lower tooling costs and minimal downtime for service intervals: worn cutters are replaced rather than the entire tool, and the modular layout supports quick maintenance procedures on the shop floor, improving overall equipment effectiveness. Balanced proportions for reliable performance in production With an 88 mm cutting length, 166 mm overall length and a mass of 0.425 kg, the drill body offers a balance between reach and rigidity that suits repetitive machining tasks. The measured geometry helps to maintain tool life and workpiece quality, while the modest weight contributes to smoother acceleration and deceleration on CNC spindles. For workshops seeking dependable repeatability, this configuration supports stable drilling cycles and efficient integration into tool inventories. Contact Metav Werkzeuge for a technical consultation on the Teknik Makina Indexable Insert Drill U418TM (SKU U418TM) and to request a tailored supply recommendation from Emmerich. Technical Data Article number: U418TM Manufacturer: Teknik Makina Product name: Indexable insert drill (Vollbohrer) Facts Diameter: 22 mm Overall length: 166 mm Cutting length: 88 mm Shank length: 56 mm Shank diameter: 25 mm Weight: 0.425 kg Special features Compatible insert: SOMT 0703 Compatible insert manufacturer: Taegutec Designed for replaceable cutting inserts and easy reconditioning FAQ Which inserts fit this drill body? The drill body accepts Taegutec SOMT 0703 inserts; Teknik Makina’s U418TM is configured for this standard insert size to ensure broad availability and simplified stocking. What are the critical dimensions for toolholding? Key dimensions are a 25 mm shank, Ø 22 mm cutting diameter, 88 mm cutting length and 166 mm overall length, which should be checked against the machine’s toolholder and available clearance before use. How does the tool help reduce downtime? By using replaceable SOMT 0703 inserts, wear is managed at the insert level rather than replacing the whole tool body, so the U418TM enables fast cutter changes and lower per-hole tooling costs. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a sturdy indexable system and precise dimensions to keep production cycles reliable: the combination of a Ø 22 mm cutting diameter, a 25 mm shank and compatibility with SPMG 07T3 inserts delivers efficient holemaking and quick tool changes. Order the tool through Metav Werkzeuge or contact the consultants for application support. Vollbohrer – Indexable insert drill body, Ø 22 mm, Teknik Makina The Vollbohrer is an indexable insert drill body engineered for standardised insert use and medium-depth holemaking in workshop and production environments. Indexable system for SPMG 07T3 inserts 25 mm shank for secure clamping 66 mm effective cutting length Compatible with Taegutec and YG-1 inserts Higher throughput with standardised inserts The indexable design of this drill body supports fast insert changes and consistent cutting performance, which reduces downtime and keeps cycle times predictable. With an effective cutting length of 66 mm and a Ø 22 mm cutting diameter, the tool body is suited to repetitive drilling tasks where tool-change speed and repeatability matter. The use of standard SPMG 07T3 inserts means access to a wide range of grades and geometries from established suppliers, enabling optimisation of tool life and cutting parameters. Compatibility with recognised insert manufacturers further simplifies stock management and purchasing. Rigidity and clamping certainty for accurate holes A robust 25 mm shank and the balanced geometry of the holder translate into improved run-out characteristics and axial stability during drilling, which helps achieve tighter tolerances and better surface finish. The 145 mm overall length and the defined shank length provide clear guidance for clamping depth in common holders and adaptors. These mechanical attributes support consistent hole quality across batches, which is particularly advantageous for production runs where dimensional consistency is critical. Practical integration into the workshop workflow The drill body accepts common insert grades from suppliers such as Taegutec and YG-1, easing procurement and replacement. The modular approach of using an insert-compatible body reduces the need for complete tool replacement after wear; only the inserts are exchanged. This lowers consumable costs over time and simplifies inventory. The moderate weight of the assembly supports handling during set-up while the standardised connection dimensions permit rapid fixture into established drilling spindles and adaptors. Contact Metav Werkzeuge for tailored application advice on the Teknik Makina indexable insert drill body U822TM — reach the Metav team at +49 2822 7131930 or info@metav-werkzeuge.com Technical data SKU: U822TM Manufacturer: Teknik Makina Diameter: 22 mm Overall length: 145 mm Cutting length: 66 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.375 kg Compatible inserts: SPMG 07T3 Compatible insert manufacturers: Taegutec, YG-1 Product type: Indexable insert drill body FAQ What insert type fits this drill body? The drill body accepts SPMG 07T3 inserts; compatible grades from Taegutec and YG-1 are suitable for the holder. Which machines or holders are required for the shank? The 25 mm shank requires a matching holder or chuck with sufficient clamping length for the 56 mm shank seating; verify holder capacity before installation. What drilling depth can be achieved with this tool? The tool provides an effective cutting length of 66 mm, with an overall length of 145 mm for handling and clamping considerations. Is the tool supplied with inserts? The delivery data does not list inserts as included; inserts such as SPMG 07T3 should be ordered separately from compatible manufacturers. What is the SKU and manufacturer for reference? Reference SKU U822TM, manufactured by Teknik Makina, for ordering and technical enquiries. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, insert-driven drilling solution that combines precise holemaking with quick insert changes and secure clamping — ideal for batch production and rapid tool exchange. Benefit from a 22 mm cutting diameter and a 25 mm shank for stable setup; order directly via Metav Werkzeuge or consult the technical team for application advice. Indexable insert drill U922TM by Teknik Makina — 22 mm diameter, 25 mm shank The Indexable insert drill U922TM is a purpose-built drill body for CNC holemaking with SPMG 07T3 indexable inserts, designed to deliver stable, repeatable results in batch and single-piece production. 22 mm cutting diameter for standard holes Compatible with SPMG 07T3 indexable inserts 25 mm shank for robust clamping Lightweight 0.34 kg — easy handling High-precision drilling performance for repeatable results The U922TM drill body is engineered for consistent hole quality and minimal setup variation. With a 22 mm nominal diameter and a 44 mm cutting length, the tool balances reach and rigidity to reduce runout and vibration during machining. The insert-driven design ensures that cutting edges can be renewed without regrinding the tool body, which maintains hole tolerance and surface finish across production runs. The compatibility with industry-standard insert formats simplifies procurement and inventory management while preserving productivity. Lower running costs through insert interchangeability Indexable tooling brings clear economic advantages in medium- to high-volume workshops. The U922TM accepts the SPMG 07T3 insert family and is also compatible with major insert suppliers Taegutec and YG-1, allowing shops to choose the best-performing grade for each application. Using indexable inserts reduces tool-change downtime and per-cutting-edge cost compared with solid-carbide alternatives, so the overall cost per hole falls rapidly in series production while maintaining machining security. Practical dimensions for straightforward integration Designed for straightforward mounting, the body features a 25 mm shank and an overall length of 123 mm, making it suitable for many standard toolholders and adaptors. The 0.34 kg mass keeps centrifugal loads low and facilitates handling during tool changes. A shank with tight tolerances and a compact overall length helps to reduce cantilever effects, improving concentricity and allowing for more aggressive feeds where the machine and workholding permit. Reliable supply and expert backing from Metav Werkzeuge Metav positions itself as a partner for precision: a broad stock and a disciplined quality filter at Emmerich support reliable delivery and consistent product selection. The U922TM is offered within that supply chain, which aims to reduce lead times and simplify procurement. Technical consultations are available for selecting insert grades or confirming holder compatibility, ensuring the chosen setup matches the required material and finish parameters. Discuss application requirements with Metav Werkzeuge in Emmerich to confirm the U922TM matches the machining task and to arrange supply or expert consultation. Technical data Article number: U922TM Manufacturer: Teknik Makina Product designation: Indexable insert drill Facts Diameter: 22 mm Overall length: 123 mm Cutting length: 44 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.34 kg Special features Compatible with inserts: SPMG 07T3 Compatible insert manufacturers: Taegutec, YG-1 Insert-driven concept for quick edge change FAQ What materials is this drill suitable for? The U922TM is an indexable insert drill body; material suitability depends on the chosen insert grade. With appropriate SPMG 07T3 inserts, the tool can be adapted for a wide range of steels and general workshop materials. Which inserts fit the U922TM? The drill accepts SPMG 07T3 inserts and is compatible with inserts from Taegutec and YG-1, allowing selection of grades optimised for wear resistance or toughness. What are the key dimensions to check for holder compatibility? Verify the 25 mm shank diameter and 123 mm overall length against the toolholder; the 56 mm shank engagement length is relevant for clamping depth. Can the tool achieve high metal removal rates? Metal removal rates are determined by insert geometry, grade and machine capability. The U922TM’s rigid shank and insert system support productive feeds when matched with suitable inserts and machining parameters. Is the U922TM suitable for automated tool change systems? The compact design and standard shank diameter facilitate integration into automated tool magazines provided the magazine accepts the specified shank size and overall length. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The provided product data contains a contradiction that prevents the generation of a reliable product description for SKU U318TM. The item is labelled as "Vollbohrer" (which denotes a solid drill), while separate fields specify compatibility with indexable inserts — in particular the insert type SOMT 0703 and the insert manufacturer Taegutec. These entries imply an indexable‑insert drill body rather than a solid drill, so the core function and tool category are unclear. To avoid misleading technical information, a complete product text cannot be produced until the source data is corrected. Please confirm whether the tool is a solid twist drill or an indexable‑insert drill body, and verify related fields such as insert compatibility, shank and cutting geometry. Once the discrepancy is resolved, a full, standards‑accurate British English product description can be provided.

Benefit from the secure combination of a 25 mm shank for stable clamping and insert compatibility with Korloy WCM‑0402, engineered to keep drilling cycles efficient and predictable. Order the tool directly via Metav Werkzeuge or consult the technical advisors if additional specifications are required. Indexable drill (Vollbohrer) – 22 mm diameter, 25 mm shank · Teknik Makina A robust indexable drill engineered for insert cutting with Korloy WCM‑0402, designed for stable holemaking and dependable performance in production and workshop environments 22 mm cutting diameter Compatible with WCM-0402 inserts 25 mm shank for stable clamping Total length 123 mm, cutting length 44 mm Precision and repeatability for serial drilling The design focuses on repeatable results in production runs: a well-balanced geometry and insert-compatible head reduce variation between holes and simplify tool management. Compatibility with Korloy WCM‑0402 insert geometry allows rapid insert replacement without regrinding, which shortens unproductive downtime and helps maintain a consistent hole quality. The result is an efficient process chain where cycle times are predictable and tool changes are straightforward. Secure clamping and rigid toolholder interface A 25 mm shank delivers a reliable interface with standard toolholders and collets, increasing resistance to vibration and improving surface finish. With a total length of 123 mm and a cutting length of 44 mm, the drill balances reach and rigidity for medium-depth holes. The compact mass and balanced proportions reduce deflection under load, contributing to longer insert life and fewer scrap parts in demanding applications. Lower operating costs through insert strategy Using an indexable system with WCM‑0402 inserts separates the cutting edge from the tool body, enabling economical replacement of worn edges rather than the entire tool. This approach lowers cost per hole and supports lean inventory management in production environments. The concept is especially suitable where repeatable hole tolerances and fast tool turnarounds are required, making the tool a practical choice for workshop and small-series manufacturing. Practical handling and logistics benefits With a tool weight of 0.345 kg, handling and fixture changes are uncomplicated, while standard shank dimensions simplify integration into existing setups. Technical documentation and files are provided with the article to aid setup and programming, supporting rapid commissioning at the machine. The compact design also helps to reduce spindle load, supporting steady performance across shift cycles. Contact Metav Werkzeuge for tailored procurement advice on Teknik Makina indexable drills — available from Emmerich with reliable supply and technical support; eMail: info@metav-werkzeuge.com · Tel: +49 2822 7131930 Technical data Article number: U112TM Manufacturer: Teknik Makina Product name: Vollbohrer Dimensions & weights Diameter: 22 mm Total length: 123 mm Cutting length: 44 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.345 kg Compatibility & features Insert type: WCM-0402 Compatible insert maker: Korloy Files: 62de7ec4bd24461b3d5f7a4f, 62de7ddb0f56dbb4de4dbedf FAQ What is the recommended insert type for this drill? The drill is specified for WCM‑0402 inserts; compatibility with Korloy inserts is confirmed for this indexable system. How does the 25 mm shank improve machining results? A 25 mm shank provides a rigid clamping interface that reduces vibration and deflection, improving hole accuracy and prolonging insert life on the Teknik Makina indexable drill SKU U112TM. Can this drill be used in automated multi-spindle operations? Yes, the balanced geometry and standard shank size make the drill suitable for integration in automated setups where stable clamping and repeatable hole quality are required. What are the key dimensions to check before selecting a toolholder? Check the 25 mm shank diameter, the 56 mm shank length and the overall length of 123 mm to ensure correct toolholder seating and sufficient clearance. Are setup files available for machine programming? Yes, accompanying files are listed with the article and can be used to support setup and CAM programming for the U112TM tool. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust indexable insert drill that pairs Ø22 mm holemaking, a shank Ø25 mm for secure clamping and an 88 mm effective cutting length to sustain consistent production runs; order the U612TM directly via Metav Werkzeuge or consult the technical team for specification matching. U612TM indexable insert drill body — Ø22 mm, shank Ø25 mm (Teknik Makina) The U612TM indexable insert drill body is engineered for precision holemaking in industrial machining, accepting Korloy WCM‑0402 inserts for efficient, repeatable performance in production and workshop environments Ø22 mm drill diameter 88 mm effective cutting length Shank Ø25 mm for stable clamping Compatible with Korloy WCM‑0402 inserts Consistent cutting performance through stable geometry The indexable insert design combines a rigid body with a dedicated 88 mm cutting length to deliver constant chip control and dimensional stability. The tool’s Ø22 mm nominal diameter and a shank Ø25 mm ensure compatibility with common toolholders while minimising runout. For production contexts where repeatability matters, the arrangement of the insert pockets and the body’s geometry reduce vibration and distribute cutting forces evenly, which helps to preserve tool life and maintain hole tolerance without frequent corrections. Cost efficiency and quick servicing with indexed inserts Compatibility with WCM‑0402 inserts from Korloy enables rapid index changes and cost-effective replenishment of the cutting edge. Instead of replacing whole drills, worn cutting edges are rotated or replaced, reducing downtime and inventory costs. The tool’s modular approach supports predictable maintenance cycles and simpler tool management in the workshop. Where operators require a straightforward description: an indexable insert drill means the cutting part is replaceable and indexed, so workshop staff can restore cutting performance quickly without regrinding. Practical handling, clamping and integration in the toolroom The overall length of 167 mm, a 56 mm shank length and a mass of 0.43 kg balance accessibility with secure clamping in standard fixtures. The shank dimensions permit high‑precision mounting in collets or shrink fit holders that accept cylindrical shanks, improving concentricity and enabling higher material removal rates within recommended limits. Documentation and SKU tracking (U612TM) simplify procurement and tool presetting; technical drawings or preset data can be maintained centrally to support setup consistency across multiple machines. For procurement or technical consultation on integrating the U612TM indexable insert drill body into existing tool sets, contact Metav Werkzeuge for tailored advice and supply at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: U612TM Item name: Indexable insert drill body (translated from Vollbohrer) Manufacturer: Teknik Makina Core data Diameter: 22 mm Overall length: 167 mm Cutting length: 88 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.43 kg Compatibility & features Compatible insert type: WCM‑0402 Compatible insert manufacturer: Korloy Application: indexable insert drilling FAQ Which inserts fit this drill body? The drill body accepts WCM‑0402 indexable inserts; Korloy‑spec inserts listed as WCM‑0402 are compatible with the U612TM. What is the effective cutting length and why it matters? The 88 mm cutting length defines the maximum useful engagement of the cutting edges; it determines the reachable hole depth without sacrificing stability and influences chip evacuation. What shank size is required for clamping? A shank Ø25 mm is specified for stable mounting; the 56 mm shank length is provided for secure seating in standard holders. Is the tool suitable for simple workshop presetting? Yes — the modular indexable design and defined dimensions (Ø22 mm, 167 mm overall) support straightforward presetting and consistent replacement of inserts. How is tool life extended with this design? Tool life is improved by replacing or rotating WCM‑0402 inserts rather than the whole body, lowering tooling costs and reducing downtime for regrinding. Hersteller: Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a precise 22 mm nominal diameter and an 88 mm cutting length to maintain production flow with fewer tool changes; the robust 25 mm shank and 56 mm clamping length ensure secure mounting and repeatable results. Order the tool directly via Metav Werkzeuge or contact our consultants for application advice. Indexable Insert Drill Body U722TM — 22 mm, SPMG 07T3 compatible by Teknik Cutting Tools The Indexable Insert Drill Body U722TM is a purpose-built drill holder for indexable insert drilling in milling and turning centres, engineered to deliver stable holemaking performance in medium-deep applications. 22 mm nominal diameter for reliable holemaking Compatible with SPMG 07T3 indexable inserts 88 mm effective cutting length for deeper holes 25 mm shank for secure clamping in toolholders Longer reach for fewer tool changes The holder provides an effective cutting length of 88 mm, paired with a total length of 167 mm, which extends reach without compromising rigidity. This combination reduces the need for intermediate tool swaps during medium-deep hole operations and supports consistent cycle times on batch runs. The extended reach is balanced by a design that maintains concentricity, so the machining process stays within tolerance windows while increasing operational efficiency. Secure clamping and repeatable set-up A 25 mm shank diameter and a 56 mm clamping length give dependable axial support and torque transmission in standard toolholders. The specified shank length and overall mass of 0.417 kg contribute to stable cutting conditions and reduced vibration at cutting speeds appropriate for indexable insert drilling. As a result, set-up times are shorter and runout is minimised, which supports higher first-pass yields and predictable surface finish. Broad insert compatibility for lower tooling cost Designed to accept SPMG 07T3 inserts, the drill body is compatible with inserts from established suppliers such as Taegutec and YG-1, enabling flexible sourcing and straightforward exchange of cutting edges. Using indexable inserts reduces per-hole tooling costs and simplifies maintenance: worn inserts are replaced in seconds while the drill body remains in the spindle. This approach supports predictable tool budgets and rapid recovery from wear-related downtime. Practical design for workshop throughput The U722TM model balances reach, rigidity and serviceability to suit high-mix and mid-volume production environments. The geometry supports reliable chip evacuation within its effective cutting length, and the straightforward insert seats speed up maintenance intervals. For teams seeking to centralise tooling purchases, the drill body integrates with common holders and insert systems, allowing streamlined inventory management and rapid tool changeovers on the shopfloor. Contact Metav Werkzeuge for application recommendations and to arrange supply of the Teknik Cutting Tools Indexable Insert Drill Body U722TM — info@metav-werkzeuge.com or +49 2822 7131930 Technical details Article number: U722TM Manufacturer: Teknik Makina Key measurements Diameter: 22 mm Total length: 167 mm Cutting length: 88 mm Shank diameter: 25 mm Shank length: 56 mm Weight: 0.417 kg Compatibility & features Compatible inserts: SPMG 07T3 Compatible insert manufacturers: Taegutec, YG-1 Indexable insert drill body for medium-deep holes FAQ Which inserts fit this drill body? The drill body accepts SPMG 07T3 indexable inserts; compatible manufacturers include Taegutec and YG-1, simplifying procurement and replacement. What are the key dimensions for setting up the holder? Nominal diameter is 22 mm, effective cutting length 88 mm, total length 167 mm, and shank diameter 25 mm; these values apply to the U722TM model and are useful for toolholder and spindle selection. Is the tool suitable for deeper holemaking? The design supports medium-deep holes within its 88 mm cutting length, offering extended reach while maintaining stability for consistent hole quality. How is the drill body clamped in a toolholder? Clamping is via the 25 mm shank with a 56 mm clamping length to ensure secure seating and repeatable positioning in standard toolholders for reliable machining with indexable inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of precise holemaking with a stable 25 mm shank and a 22 mm cutting diameter combined with a 66 mm effective cutting length for consistent cycle times and reduced rework. Order the solid drill directly via Metav Werkzeuge or consult our specialists for application advice. Solid drill U154TM — 22 mm diameter, 66 mm cutting length The Solid drill U154TM is a robust, indexable-insert drilling tool designed for precise axial drilling applications with Korloy-compatible inserts, suitable for production environments and machine-shop use 22 mm diameter for robust holes 66 mm effective cutting length 25 mm shank for stable clamping Compatible with Korloy WCM-0402 inserts Consistent hole quality for demanding production The tool is engineered to deliver repeatable hole geometry across batches thanks to its rigid 25 mm shank and optimised proportions. The combination of a 22 mm diameter and a 66 mm cutting length provides a balance between reach and rigidity, so axial deflection is minimised and cycle-to-cycle variation is reduced. For machining centres and turret lathes this results in fewer rejects and less secondary finishing. The moderate mass of the assembly (approx. 0.385 kg) makes handling straightforward while still providing the inertia needed for steady cutting performance. Faster uptime through indexable-insert compatibility Compatibility with Korloy WCM-0402 indexable inserts enables economical edge changes and consistent cutting performance without full-tool replacement. Insert swaps are quick and require only minimal setup time, which shortens downtime and keeps throughput high. The tool’s interface and 56 mm mounting length ensure firm clamping in standard holders, so insert life can be exploited reliably. For operations aiming to improve overall equipment effectiveness, the modular approach to cutting edges is a straightforward efficiency lever. Practical integration and trusted supply chain The geometry and dimensions—145 mm total length with a robust shank—allow straightforward integration into common tool holders and machine-tool toolrooms. Specification-driven procurement is simplified by the clear, verifiable measurements: diameter, cutting length, shank diameter and mounting length are stated values that support planning and fixture design. Metav’s warehouse in Emmerich acts as a quality filter for the European market, offering reliable availability and specialist advice should further clarification be required. The product is therefore suitable where stable drilling performance and predictable supply are priorities. Contact Metav Werkzeuge for tailored application advice on Teknik Cutting Tools’ Solid drill U154TM and to confirm insert compatibility for the intended machining task. Technical data Article number: U154TM Manufacturer: Teknik Makina EClass: 21180201 SKU: U154TM Data Diameter: 22 mm Total length: 145 mm Cutting length: 66 mm Shank diameter: 25 mm Shank/mounting length: 56 mm Weight: 0.385 kg Special features Compatible inserts: Korloy WCM-0402 Files available: 62de7ec3a9cff922f4703d40, 62de7ddaa9cff922f4703d13 FAQ What machine types is this drill suited for? The U154TM solid drill is designed for use in machining centres and turret lathes where indexable-insert drilling is employed and a rigid 25 mm shank is supported. Which inserts fit the tool? The tool accepts Korloy WCM-0402 indexable inserts; compatibility is specified to enable quick edge replacement and consistent cutting performance. How long is the cutting portion of the drill? The effective cutting length is 66 mm, providing sufficient reach while maintaining rigidity for stable holemaking. What is the total length and mounting length of the tool? Total length is 145 mm and the mounting/shank length is 56 mm, suitable for standard holders that accept a 25 mm shank. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of reliable indexable‑insert compatibility, robust shank dimensions and a long cutting length for steady production cycles; order directly via Metav Werkzeuge or consult our specialists for tailored advice. Shank Milling Cutter S187TM — for APXT 1003 indexable inserts, Ø22 mm, 3 cutting edges (Teknik Makina) A Shank Milling Cutter S187TM engineered for efficient face and shoulder milling with APXT 1003 indexable inserts, suitable for medium‑duty production environments 22 mm cutting diameter Shank diameter 20 mm 3 cutting edges 70 mm cutting length Compatible with Korloy inserts Consistent material removal for repeatable runs The tool is designed to deliver steady metal removal thanks to a 90° cutting geometry and three precisely spaced cutting edges. With a Ø22 mm cutting diameter combined with a shank Ø20 mm, the design provides a stable interface between spindle and cutter, reducing run‑out and vibration. This stability translates into improved surface quality and longer insert life, making the tool an economic choice for serial machining tasks that prioritise uptime and predictability. Secure clamping and simple insert fixation Compatibility with APXT 1003 indexable inserts and a Torx clamping screw (M2.5×5.5) operable with a T8 key ensures straightforward insert changes and reliable fixation during interrupted cuts. The long 70 mm cutting length reduces the need for frequent tool changes when machining stepped or deep features, while the tool’s balanced mass (approx. 0.513 kg) supports consistent spindle behaviour. Clear mechanical interfaces mean shorter set‑up times and more consistent process control on the shop floor. Practical fit for mixed production environments With an overall length of 200 mm and three cutting edges, the cutter is suited to general workshop and light industrial applications where versatility and repeatability matter. The combination of a robust shank and standardised insert system allows for quick adaptation to different workpiece geometries and materials when paired with appropriate APXT 1003 grades. For buyers seeking a dependable milling solution that integrates into established tool inventories, this shank cutter offers a good balance between rigidity and accessibility of replacement inserts. Discuss your machining requirements with Metav Werkzeuge to confirm suitability for specific materials and production conditions, or request a tailored quotation through Metav Werkzeuge for the S187TM. Technical data Article number: S187TM Manufacturer: Teknik Makina Type: Shank milling cutter Designation: for APXT 1003 Indexable Inserts eClass: 21180806 ETIM: EC011860 Facts Cutting diameter: 22 mm Shank diameter: 20 mm Cutting length: 70 mm Overall length: 200 mm Number of cutting edges: 3 Cutting angle: 90° Weight: 0.513 kg Torx screw: M2.5×5.5 Torx key: T8 Special features Compatible inserts: APXT 1003 Suitable insert manufacturer: Korloy SKU: S187TM Files available: 2 linked files FAQ Which inserts fit this shank cutter? The shank milling cutter accepts APXT 1003 indexable inserts; compatible grades from Korloy are commonly used with this tool. What shank diameter is required for machine mounting? A 20 mm shank diameter is specified for the S187TM and is intended for collets or holders sized to that diameter. How long is the effective cutting length? The tool provides a 70 mm cutting length, enabling machining of deeper features without frequent tool changes. What is the cutting diameter and how many cutting edges are fitted? The cutter has a 22 mm cutting diameter and is configured with three cutting edges for balanced removal and finish. Which screw and key are used to secure the inserts? Inserts are clamped with a Torx screw M2.5×5.5, tightened with a T8 Torx key for reliable fixation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, purpose-built boring tool that accepts widely available CCMT 0602 indexable inserts and covers a practical bore range of Ø 23–28 mm; order the tooling directly via Metav Werkzeuge or consult the specialists for application advice. Boring tool TKB174TM – Internal boring tool for WCMX and CCMT indexable inserts, Ø 23–28 mm, M12 thread (Teknik Makina) A Boring tool TKB174TM designed for internal turning and finishing where a short overhang and reliable insert clamping are required, compatible with CCMT 0602 indexable inserts for flexible workshop stocking Ø 23–28 mm cutting diameter range M12 mounting thread Compatible with CCMT 0602 inserts 72 mm total length Precise compatibility that reduces tooling variety and downtime The tool is built around a standard insert format, accepting CCMT 0602 indexable inserts and WCMX-style options, which gives an immediate logistical benefit: commonly stocked inserts can be used across multiple holders, reducing inventory complexity. The compatibility with established insert geometries ensures repeatable edge positioning and predictable wear patterns, which simplifies process planning and lowers effective tooling cost over time. Using a standard insert also enables rapid replacement and minimal spindle idle time, supporting continuous shop-floor throughput. Compact design for improved rigidity and concentricity A short overall length of 72 mm combined with an M12 mounting thread reduces cantilever and improves stability during internal operations. The reduced overhang lowers vibration potential and supports closer tolerances in bored features, which is particularly useful in confined bores where tool deflection would otherwise degrade finish and roundness. At a mass of 0.145 kg, the holder is easy to handle and quick to change while imposing minimal additional load on turrets or adaptors, helping to maintain cycle consistency in production runs. Practical integration, serviceability and workshop benefits The holder’s Ø 23–28 mm application window covers a useful span of small- to mid-diameter bores, making it suitable as a standardiser for multiple jobs. The TKB174TM accepts readily available inserts, so maintenance routines become straightforward and spare parts procurement is simplified. The M12 thread offers secure seating and straightforward replacement; the result is predictable clamping repeatability and reduced set-up time. For operations seeking to balance flexibility, tool life and straightforward maintenance, this holder provides a pragmatic solution without unnecessary complexity. Discuss machining requirements with Metav Werkzeuge’s tooling specialists in Emmerich for tailored recommendations on the TKB174TM; email info@metav-werkzeuge.com or call +49 2822 7131930 to align tool selection with specific applications. Technical data Article number: TKB174TM Manufacturer SKU: TKB174TM Measurements & weights Cutting diameter range: 23–28 mm Total length: 72 mm Thread: M12 Weight: 0.145 kg Compatibility & features Compatible with CCMT 0602 indexable inserts For use with WCMX and CCMT indexable inserts Application: internal boring / finishing FAQ What insert types fit this boring holder? The holder is compatible with CCMT 0602 inserts and WCMX-style indexable inserts, allowing use of standard ground geometries for finishing and light roughing. What bore sizes are covered by this tool? This boring tool accommodates bores in the Ø 23–28 mm range and is intended for internal turning tasks within that span. How is the tool mounted to the turret or adaptor? Mounting is achieved via an M12 thread, offering secure clamping and straightforward replacement during tool changes. Is the TKB174TM suitable for heavy-depth cuts? The TKB174TM is optimised for compact installations where rigidity is required; specific cutting depths depend on machine setup, insert grade and workpiece material. How heavy is the holder and how does that affect handling? The holder weighs 0.145 kg, which supports easy handling and minimal additional load on turrets or adaptors during index changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Reliable, insert-compatible drilling combines a 23.5 mm diameter with a 69 mm cutting length and a robust 25 mm shank for secure clamping and consistent hole quality; ideal for production runs requiring fast indexable insert changes. Order the indexable drill directly via Metav Werkzeuge or consult our specialists for matching Taegutec inserts and application guidance. Indexable drill U321TM – Ø 23.5 mm, 147 mm overall length (Teknik Cutting Tools) Indexable drill U321TM is an insert-equipped drill for precision holemaking in production and workshop environments, designed to accept SOMT 08T3 inserts from Taegutec for straightforward insert replacement and repeatable results. Compatible with Taegutec SOMT 08T3 inserts Diameter 23.5 mm for standard hole sizes Overall length 147 mm for deep reach Shank Ø 25 mm for secure clamping Consistent hole quality through optimised cutting geometry The U321TM indexable drill delivers repeatable hole quality by combining a controlled cutting length with a rigid shank geometry. The 69 mm cutting length and 147 mm overall length allow deeper holes with reduced vibration, while the 25 mm shank ensures reliable clamping in standard toolholders. For production-oriented operations this means fewer scrapped parts and improved cycle time; the tool’s compatibility with Taegutec inserts simplifies tool servicing and minimises downtime. Fast insert changes and predictable tool life for efficiency Designed to use SOMT 08T3 inserts, the drill enables quick indexable insert replacement without specialised equipment. This reduces maintenance intervals and supports high-throughput workflows. The insert system also allows users to match grade and geometry to the workpiece, improving performance in materials where thermal and abrasive loads vary. The lightweight construction at 0.412 kg supports smoother spindle behaviour, contributing to a predictable tool life and lower overall machining costs. Application focus: production drilling and retrofit to existing setups This insert drill is suited for medium‑duty production drilling where standard hole diameters and repeatability are required. The combination of a secure 25 mm shank and indexable cutting heads makes the tool adaptable for retrofitting into existing drill holders and multi‑spindle machines. For workshops handling batch production or parts with tighter tolerances, the tool provides a balance of robustness and serviceability that supports continuous operation. Contact Metav Werkzeuge for tailored recommendations on inserts and holders for the Teknik Cutting Tools U321TM and arrange a specification check with our technical consultants at Metav Werkzeuge in Emmerich Technical data SKU: U321TM Manufacturer: Teknik Makina Diameter: 23.5 mm Overall length: 147 mm Cutting length: 69 mm Shank diameter: 25 mm Weight: 0.412 kg Compatible insert: SOMT 08T3 Compatible insert manufacturer: Taegutec Tool type: Indexable drill Shank for secure clamping FAQ What insert type does this drill use? The U321TM uses SOMT 08T3 indexable inserts; Taegutec is specified as the compatible insert manufacturer. Can the drill be clamped in standard 25 mm holders? Yes. The drill has a 25 mm shank designed for secure clamping in standard toolholders. Is the U321TM suitable for deep hole drilling? With a 147 mm overall length and a 69 mm cutting length, the U321TM is intended for deeper holes within its specified cutting range. Which applications suit this indexable drill best? The drill is best for production and workshop drilling where repeatability and fast insert changes are priorities, such as batch manufacturing or retrofit to multi‑spindle machines. Who manufactures this tool and who is the responsible distributor? Teknik Cutting Tools manufactures the product; Metav Werkzeuge acts as the responsible distributor and technical contact for European customers. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a sturdy 20 mm shank, a long 185 mm cutting length and compatibility with CCMT 0602 indexable inserts for reliable internal machining and reduced cycle times. Order the internal boring bar directly via Metav Werkzeuge or ask the consultants if needed. Internal boring bar TKB104TM — 20 mm shank, CCMT 0602 compatible (Teknik Makina) The internal boring bar TKB104TM is designed for controlled internal turning with indexable CCMT 0602 inserts, delivering stable bore finishing and straightforward insert changes for small to medium production runs 20 mm shank for stable clamping Compatible with CCMT 0602 inserts 185 mm cutting length for deep bores Total length 235 mm Engineered rigidity for repeatable bore results A robust 20 mm shank is provided to maintain concentricity and minimise vibration during internal turning, so runout is reduced and surface quality is improved. The tool body is balanced for stable rotation and the moderate weight (0.682 kg) supports safe handling while remaining rigid in the tool post. These design choices translate into fewer scrapped parts and more consistent first-pass quality on turned bores. Fast indexability and controlled chip flow Compatibility with CCMT 0602 indexable inserts enables rapid, cost-efficient insert replacement and flexible grade selection for different workpiece materials. The long 185 mm cutting length gives access to medium-depth bores without frequent tool changes. Insert geometry fosters predictable chip formation, which minimises interruptions and helps maintain steady cycle times on CNC lathes and manual turning centres. Precision where it matters — process stability The geometry and shank specification are chosen to support accurate bore diameters and repeatable finishes. The tool is suited for finishing and light-medium stock removal where dimensional stability is required. Where operators demand reproducible outcomes, the boring bar’s construction reduces the need for corrective passes, improving productivity and lowering overall machining costs. Simple integration and low-maintenance operation The boring bar is compatible with standard tool holders and is supplied for use with industry-standard CCMT 0602 inserts, simplifying inventory and maintenance routines. Routine upkeep is limited to insert changes and basic clamping checks; no specialised service tools are necessary. The tool’s total length of 235 mm allows straightforward setup in common lathe configurations, making it a practical choice for mixed-shop environments and contract workshops. Contact Metav Werkzeuge to discuss how the Teknik Cutting Tools TKB104TM boring bar with a 20 mm shank and 185 mm cutting length can streamline internal turning processes — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: TKB104TM Manufacturer: Teknik Makina eClass: 21181208 Files: 62de7eef0f56dbb4de4dbf60, 62de7e6333927e49dbf32755 Facts Shank diameter: 20 mm Cutting length: 185 mm Total length: 235 mm Weight: 0.682 kg Special features For indexable inserts CCMT 0602 SKU: TKB104TM Suitable for internal turning applications FAQ What insert type does this boring bar take? The boring bar is compatible with CCMT 0602 indexable inserts; these inserts can be selected in grades appropriate for steel, alloyed materials or finishing tasks. Is the tool suitable for deep bore machining? With a cutting length of 185 mm and a total length of 235 mm, the bar is designed for medium-depth internal machining and provides good access within common lathe envelopes. How is concentricity and vibration control achieved? Concentricity and vibration damping are achieved through the 20 mm shank and the bar’s balanced construction, which together improve surface finish and repeatability. Can the boring bar be mounted in standard tool holders? Yes, the bar is intended for use with standard turning tool holders compatible with a 20 mm shank and indexable insert systems, facilitating easy integration. What routine maintenance is required? Routine maintenance is limited to periodic insert replacement and verification of clamping torque; no specialised maintenance is required for normal workshop use. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, indexable solution that balances rigidity and insert compatibility for efficient internal machining. The combination of a shank Ø16 mm with a 52 mm effective cutting length supports stable boring cycles and predictable repeatability — order supply via Metav Werkzeuge or request an individual tooling recommendation from our consultants. TKB094TM Boring Bar – indexable boring tool, Ø19 mm nominal, CCMT 0602 compatible A TKB094TM boring bar designed for internal turning and reboring operations in CNC setups, optimised for use with CCMT 0602 indexable inserts and compact tool layouts Indexable CCMT 0602 compatibility Nominal diameter Ø19 mm Shank diameter Ø16 mm for rigid clamping 52 mm cutting length for deeper bores Engineered rigidity for repeatable internal machining The design focuses on delivering consistent, measurable results through rigid clamping and balanced geometry. With a shank Ø16 mm, the bar reduces vibration and tool deflection compared with slimmer alternatives, which improves bore roundness and surface finish. The nominal Ø19 mm profile and a modest mass of 0.192 kg help to maintain tool stability during interrupted cuts, making this tool suitable for short- to medium-length internal machining tasks where repeatability and control are priorities. Insert system that simplifies tooling logistics Compatibility with CCMT 0602 indexable inserts streamlines procurement and reduces inventory complexity. Indexable inserts allow economical edge changes: worn cutting edges are replaced rather than the entire tool, lowering operating costs and shortening downtime. For less experienced staff, an indexable system also simplifies set-up because insert seating and clamping angles are standardised; the result is quicker insert replacement and consistent cutting geometry across multiple tool holders. Integration into CNC workflows and measurable productivity gains The bar’s 52 mm cutting length and 100 mm overall length are balanced for accessible reach in most turning centres while keeping overhang minimal. The maximum cutting diameter 23 mm provides a clear performance envelope for process planning. Reduced set-up time and fewer full-tool replacements translate into higher effective machine availability and a predictable cycle time — a rational benefit for production planning and cost accounting in small-batch and serial manufacturing environments. Contact Metav Werkzeuge for a tailored technical recommendation and supply of the Teknik Cutting Tools TKB094TM boring bar, directly from our Emmerich hub. Technical data Article number: TKB094TM Manufacturer: Teknik Makina Name: Boring bar Accepts: CCMT 0602 inserts Weight: 0.192 kg Facts Nominal diameter: 19 mm Maximum cutting diameter: 23 mm Shank diameter: 16 mm Cutting length: 52 mm Overall length: 100 mm Special features For indexable CCMT 0602 inserts Shank Ø16 mm for rigid clamping Nominal Ø19 mm profile 52 mm effective cutting length Compact 100 mm overall length FAQ What insert type does this boring bar accept? The TKB094TM boring bar is specified for CCMT 0602 indexable inserts, providing standardised seating and cutting geometry for quick insert changes. What are the key dimensional limits for planning a process? Key values for planning with this boring bar are a nominal diameter of 19 mm, maximum cutting diameter 23 mm, cutting length 52 mm and overall length 100 mm. Which shank diameter is required for secure clamping? Secure clamping requires a holder or arbor compatible with the shank Ø16 mm dimension to ensure the required rigidity. How does the TKB094TM support shop-floor efficiency? By using indexable inserts and a compact geometry, the TKB094TM reduces downtime for tool changes and helps keep overhang low, contributing to steadier cycle times and less rework. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of precise insert compatibility, a stable 20 mm shank and a 50 mm effective cutting length to secure repeatable internal bores; order directly via Metav Werkzeuge or consult our specialists for application advice. Boring Tool TKB100TM (Teknik Makina) — 20 mm shank, for CCMT 0602 inserts Boring Tool TKB100TM is a precision internal boring holder designed for CNC lathes and milling machines, optimised for CCMT 0602 indexable inserts and medium-reach operations. CCMT 0602 insert compatibility 20 mm solid shank for stable clamping 50 mm effective cutting length Max cutting diameter 28 mm Accurate insert compatibility for consistent bore quality The holder is engineered for CCMT 0602 indexable inserts, which makes tool changes fast and repeatable. With a 50 mm effective cutting length and a maximum cutting diameter of 28 mm, the system is suitable for mid-range internal machining tasks where dimensional consistency is essential. Indexable inserts reduce downtime for tool regrinds and provide a measurable cost advantage in batch production, while established insert grades preserve edge life under varying cutting conditions. Stable shank and reach that reduce vibration A 20 mm shank provides a secure clamp interface that helps to maintain concentricity and reduce runout during cutting. The combination of a compact 100 mm overall length and a low mass of 0.298 kg limits overhang-induced deflection, which in turn improves surface finish and dimensional accuracy. These mechanical characteristics are particularly important when tight tolerances are required; the holder’s geometry is thereby designed to support efficient chip evacuation and minimise chatter during machining. Practical advantages for workshop and production environments The modular approach with indexable inserts simplifies inventory management and lowers per-part tooling costs in small-batch and series production. The tool’s compact design supports flexibility on conventional and CNC machines, enabling quick set-up and predictable cycle times. Metav’s position as a quality filter for Europe ensures reliable supply and technical guidance, offering purchasers the confidence that precision components are backed by experienced consultancy and a comprehensive product range. Contact Metav Werkzeuge today to discuss the Teknik Makina TKB100TM and secure a precision boring solution tailored to the application, delivered from our Emmerich stock and supported by our technical consultants. Technical Data Article number: TKB100TM Manufacturer: Teknik Makina Product: Boring tool Cutting diameter max: 28 mm Shank diameter: 20 mm Effective cutting length: 50 mm Overall length: 100 mm Weight: 0.298 kg Compatible insert type: CCMT 0602 Indexable insert holder design Compact, low-mass construction FAQ Which insert type fits this tool? The tool accepts CCMT 0602 indexable inserts; Teknika Makina’s TKB100TM is configured for this common insert geometry to simplify sourcing and changeover. What machines is the holder suited for? The holder is suitable for CNC lathes and milling machines where a 20 mm shank and a 100 mm overall length meet the required toolholder interface and reach. How does the shank diameter affect performance? A 20 mm shank improves clamping stability and reduces runout, which helps to maintain bore accuracy and surface finish during operations with the TKB100TM. Is this tool a good choice for small-batch production? Yes; the use of indexable inserts and the tool’s compact geometry make the TKB100TM a cost-effective solution for small-batch and repeatable production tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high-stability boring solution with a 16 mm shank and a 23 mm cutting diameter, compatible with DC-- 11T3 indexable inserts; order directly via Metav Werkzeuge or request advice from our technical consultants. S16Q SD-CR boring bar — compact indexable-insert boring bar, 16 mm shank, for DC-- 11T3 inserts (Teknik Makina) The S16Q SD-CR is a right-hand boring bar intended for internal turning with DC-- 11T3 indexable inserts, offering a compact 180 mm overall length for confined setups. S16Q SD-CR ISO shank for secure clamping 16 mm shank diameter for stable machining Compatible with DC-- 11T3 indexable inserts Right-hand cutting with 62.5° cutting angle Stable cutting for precise internal turning The bar provides stable clamping through a standard ISO shank design, which reduces chatter and improves surface finish in internal turning operations. A 16 mm shank and modest mass (0.288 kg) help maintain rigidity while allowing flexible setup in smaller machining centres. The 23 mm cutting diameter gives a clear indication of effective working size, and the geometry is designed to promote predictable cutting behaviour under steady feeds and speeds. This combination supports higher first-pass accuracy and fewer reworks, translating into measurable time and cost savings in production runs. Optimised for fast insert changes and consistent chip control Compatibility with DC-- 11T3 inserts means quick, repeatable insert replacement without complex regrinding. The SD-CR holder form and the 62.5° cutting angle are chosen to balance cutting forces and tool accessibility, delivering consistent chip formation and predictable load distribution. Right-hand cutting direction simplifies toolpath planning for common CNC lathe setups and reduces the learning curve for operating personnel. For teams new to indexable tooling, this arrangement shortens setup time and lowers the risk of mounting errors. Compact design that fits busy workshops With an overall length of 180 mm and a cutting height of 32 mm, this boring bar is designed for confined tool pockets and tight turret clearances. The reduced overhang curtails vibration and contributes to stable surface finishes when machining internal diameters. At only 0.288 kg, the tool is lightweight to handle but maintains the necessary mass for damping unwanted motion. The compact footprint makes the tool a practical choice for small-batch production or mixed-workshop environments where machine real estate and quick changeovers are priorities. If specific application parameters need verification, our technical team is available for guidance at info@metav-werkzeuge.com or by phone on +49 2822 7131930. Contact Metav Werkzeuge for application advice on the Teknik Makina S16Q SD-CR boring bar (SKU K172TM) and arrange prompt delivery from Emmerich with tailored technical support Technical data Article number: K172TM Manufacturer: Teknik Makina ISO designation: S16Q SD-CR Type designation (English): SD-CR for DC-- Indexable Inserts Brand: Teknik Makina Numerical data Shank diameter: 16 mm Cutting diameter: 23 mm Overall length: 180 mm Cutting height: 32 mm Weight: 0.288 kg Cutting angle: 62.5° Cutting direction: right Compatibility & features For indexable inserts: DC-- 11T3 Clamp/holder reference: 11 Suitable for internal turning with indexable inserts ISO shank holder format FAQ Which insert type fits this boring bar? The boring bar is designed for DC-- 11T3 indexable inserts; the SD-CR holder form accepts inserts in that size and seating form. What are the dimensional key figures of the tool? The tool has a 16 mm shank, a 23 mm cutting diameter and an overall length of 180 mm; weight is 0.288 kg (SKU K172TM). Is the cutting direction right- or left-handed? This model is configured for right-hand cutting and a 62.5° cutting angle suited to common internal turning operations. How does the compact length benefit small workshops? A shorter overhang reduces vibration and improves stability in confined setups, allowing more consistent surface finishes and safer tool changeovers. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com