Gibt es einen Hahn und Kolb Online Shop?

Take advantage of the combination of 25 mm shank rigidity and a 90° cutting angle for stable, repeatable milling with quick insert changes; the compatibility with LNGU 15T6 indexable inserts reduces downtime and simplifies maintenance. Order the indexable milling cutter via Metav Werkzeuge or contact our consultants for application advice. Indexable milling cutter S950TM — 25 mm shank, 90° cutting angle (Teknik Makina) The indexable milling cutter S950TM is a 90° shank-mounted cutter engineered for use with LNGU 15T6 indexable inserts, offering a compact solution for precision milling tasks in production and job-shop environments. Indexable cutter for LNGU 15T6 inserts 25 mm shank diameter for rigidity 45 mm cutting length for deep passes Torx M4x11 screw, T15 key Stable machining through rigid design and sensible geometry The combination of a 25 mm shank and a total length designed for workshop use delivers mechanical stability that reduces chatter and improves surface quality. With a 90° cutting angle, the tool provides perpendicular faces and controlled radial cutting forces, which helps to maintain tool life and workpiece tolerance. The arrangement of two cutting edges limits tool engagement per revolution, producing predictable chip flow and enabling efficient material removal while keeping spindle loads manageable. Fast insert changes and secure clamping for uninterrupted production Compatibility with LNGU 15T6 indexable inserts and a single Torx M4x11 fastening screw (key T15) allows quick, repeatable index and replacement operations, reducing maintenance time on the shop floor. The use of standard fasteners and proven insert geometry means inserts from recognised manufacturers such as Kennametal can be fitted without adaptation, which simplifies inventory and replacement logistics. This configuration supports predictable set-up times and minimises unplanned downtime. Integration into workshop workflows and assured supply The tool’s 45 mm cutting length and modest overall dimensions make it straightforward to incorporate into common toolholders and automated tool-changer cycles, contributing to smooth production planning. Supplied as a robust, ready-to-install milling solution, it benefits from Metav’s distribution and quality filtering in Emmerich — a practical advantage for procurement and long-term supply reliability. Metav’s wide range of precision tooling and industry experience further supports efficient tool selection and replenishment. Contact Metav Werkzeuge for tailored application advice and to arrange procurement of the Teknik Cutting Tools S950TM indexable milling cutter compatible with LNGU 15T6 inserts Technical data SKU: S950TM Brand: Teknik Makina Diameter: 25 mm Shank diameter: 25 mm Cutting length: 45 mm Overall length: 150 mm Number of cutting edges: 2 Cutting angle: 90° Weight: 0.547 kg Compatible inserts: LNGU 15T6 Compatible insert manufacturer: Kennametal Fastening screw: Torx M4x11 Torx key size: T15 FAQ Which inserts fit this cutter? The cutter accepts LNGU 15T6 indexable inserts; the tool is supplied and specified for use with this insert geometry. How are the inserts secured? Inserts are clamped with a Torx M4x11 screw; a T15 key is used for installation and indexing on the S950TM. Is the cutter compatible with Kennametal inserts? Yes, the S950TM is specified to work with Kennametal-compatible LNGU 15T6 inserts, enabling straightforward replacement with standard parts. What toolholder is required? A holder or collet system that accepts a 25 mm shank is required; the cutter is intended for standard shank-mount toolholders. Can the inserts be indexed on the shop floor? Yes, the design permits rapid insert indexing and replacement using the specified Torx screw and key, supporting fast maintenance cycles. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 93° cutting geometry and the rigid 20 mm shank to secure stable boring cycles and long tool life; the MDUNR interface for DN-- 1104 indexable inserts keeps tooling versatile and reduces changeovers — order directly via Metav Werkzeuge or consult the technical team for application-specific guidance. S20R MDUNR boring bar — 93° geometry, MDUNR for DN-- 1104 (Teknik Makina) A S20R MDUNR boring bar engineered for external boring with DN-- 1104 indexable inserts, offering a compact 20 mm shank and 50 mm cutting height for precision steel machining. 93° cutting geometry for stable boring Compatible with DN-- 1104 indexable inserts 20 mm shank for rigid machine mounting 50 mm cutting height for deep operations Predictable chip flow and consistent bore quality The 93° cutting geometry provides a neutral engagement that improves chip flow and reduces radial loads during external boring. When paired with DN-- 1104 indexable inserts, the toolholder produces repeatable bore finishes and minimises vibration, which translates into shorter cycle times and fewer rework passes. This geometry is particularly beneficial in production where consistency across batches is required; the result is improved process stability and a measurable uplift in productivity. Rigid mounting for repeatable accuracy A 20 mm shank combined with a 200 mm overall length gives a balance between reach and stiffness that suits many CNC turning and boring centres. The 50 mm cutting height supports deeper insert engagement without sacrificing clamping security, helping to maintain tool life and surface integrity. The compact design reduces overhang and optimises toolholder dynamics, which supports tighter tolerances and reduces the risk of chatter during demanding steel machining operations. Versatile insert interface to streamline tooling Designed specifically for the MDUNR insert pocket, compatibility with DN-- 1104 indexable inserts simplifies inventory and tool setup. The right-hand cutting direction is suitable for standard turning and boring cycles on most lathes and machining centres, and the indexable system enables fast insert changes, lowering downtime and enabling quick tool recovery between jobs. The result is fewer tooling variants on the shelf and more time producing finished components. Built for workshop reliability and predictable production With a compact weight of 0.508 kg and a 25 mm diameter body where relevant, the holder is sufficiently robust for high-use environments while remaining easy to handle during tool changes. The construction supports repeated clamping forces without loss of alignment, offering long-term stability in serial machining. For operations that demand dependable performance and straightforward insert management, this toolholder provides a pragmatic combination of durability and practical geometry. For availability, compatibility checks or advice on integrating the S20R MDUNR boring bar into existing setups, contact Metav Werkzeuge in Emmerich by phone or e‑mail for direct technical consultation and reliable supply. Technical Data SKU: K408-1TM Manufacturer: Teknik Cutting Tools ISO designation: S20R MDUNR Facts Shank diameter: 20 mm Overall length: 200 mm Cutting height: 50 mm Cutting angle: 93° Diameter: 25 mm Weight: 0.508 kg Cutting direction: right Special features Compatible with DN-- 1104 indexable inserts MDUNR insert interface Right-hand cutting geometry Suited for precision steel machining FAQ Which inserts fit this boring bar? The boring bar accepts DN-- 1104 indexable inserts in the MDUNR pocket — these inserts provide quick indexing and secure clamping for external boring. Is this tool suitable for steel machining? Yes, the design and geometry of the toolholder are optimised for high-quality steel machining and robust production tasks. What are the key dimensions for mounting? The holder features a 20 mm shank and a 200 mm overall length; the cutting height is 50 mm, which supports deeper insert engagement. What is the cutting direction of the tool? The tool is configured for a right-hand cutting direction, suitable for standard external boring operations. What is the SKU for ordering and reference? Reference SKU K408-1TM when enquiring about the S20R MDUNR boring bar to ensure correct identification and supply. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the practical combination of a 93° cutting angle and right-hand cutting for stable, repeatable operations; the compact dimensions and lightweight design support efficient tool changeovers and predictable cycle times. Order directly via Metav Werkzeuge or consult our specialists for integration advice. S20R MTUNR Boring Bar (K441TM) – 93° right-hand, Ø25 mm reach (Teknik Makina) The S20R MTUNR boring bar is a purpose-built toolholder for TNMG indexable inserts, designed for right-hand cutting operations where controlled chip formation and consistent bore finish are required. Right-hand cutting, 93° cutting angle Compatible with TNMG 1604 inserts Shank Ø20 mm for secure clamping 200 mm overall length, weight 0.513 kg Stable insert mounting for consistent bore quality The S20R MTUNR toolholder combines a 93° cutting angle with a secure insert seat to reduce chatter and promote repeatable results when using TNMG 1604 indexable inserts. The geometry supports positive chip flow and a controlled cutting engagement, which helps to preserve insert life and maintain surface finish over longer production runs. By relying on a conventional insert form factor, the toolholder simplifies stock management and enables fast, predictable index changes during planned maintenance or routine insert rotation. Engineered dimensions for predictable machine behaviour Measured dimensions are tuned for workshop compatibility: a shank diameter of 20 mm, an effective diameter of 25 mm and a 200 mm overall length provide reach without excessive overhang, helping to reduce vibration and maintain concentricity. The cutting height of 50 mm ensures correct insert positioning in many standard toolposts and turrets, and the low weight of 0.513 kg reduces dynamic loads on bearings and slides. These dimensional choices deliver a balance between accessibility in confined setups and the rigidity needed for stable boring operations. Faster set-up and reliable production throughput Designed for indexable inserts, this toolholder supports quick insert replacement and reduced downtime compared with regrindable cutters. The right-hand cutting orientation and standard clamping interface mean straightforward integration into existing turning and boring processes, permitting easy exchange between holders or machines. With its compact profile and proven mechanics, the holder contributes to predictable cycle times and fewer process interruptions, supporting lean production goals and consistent part quality. For tailored technical advice or to arrange supply of the S20R MTUNR boring bar (K441TM), contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com • +49 2822 7131930 — experts are available to assist with machine integration and order planning. Technical Data Article number: K441TM Manufacturer: Teknik Makina ISO designation: S20R MTUNR Model designation (EN): MTUN for TNMG Indexable Inserts Dimensions & Weights Diameter: 25 mm Shank diameter: 20 mm Cutting height: 50 mm Overall length: 200 mm Weight: 0.513 kg Cutting angle: 93° Direction: right Compatibility & Features For TNMG 1604 inserts Clamping holder size: 16 Right-hand cutting Files: 62de7ed30f56dbb4de4dbf43, 62de7e33a9cff922f4703d1b FAQ Which indexable inserts fit this holder? The S20R MTUNR boring bar (Teknik Makina, K441TM) is specified for use with TNMG 1604 indexable inserts. What are the key dimensions to check for machine setup? Relevant dimensions include shank Ø20 mm, overall length 200 mm, effective diameter 25 mm and cutting height 50 mm; weight is 0.513 kg. Is the cutting direction left or right? This toolholder is configured for right-hand cutting with a 93° cutting angle. Does the product data state suitable materials to machine? The supplied specification identifies compatibility with TNMG inserts but does not list specific workpiece materials; material suitability depends on insert grade and cutting parameters. What clamping or holder size is required? The data indicates a clamping holder size of 16 and a standard TNMG insert seat for secure attachment. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a 95° cutting angle, integrated internal coolant and a sturdy 25 mm shank for stable, long-running turning operations; order the boring bar directly via Metav Werkzeuge or ask our consultants if needed. Boring Bar PWLN for WNMG Indexable Inserts — 95° A25S PWLNR (Teknik Makina) The Boring Bar PWLN for WNMG Indexable Inserts is a 95° toolholder designed for precision turning with internal coolant and a compact 25 mm shank for workshop versatility 95° cutting angle for stable engagement Internal coolant for improved chip evacuation Compatible with WNMG 0804 indexable inserts 25 mm shank, 250 mm overall length Stable engagement and consistent surface quality for turning tasks The 95° geometry, specified as 95° cutting angle, together with the A25S PWLNR designation, provides a toolholder profile that favours rigidity and consistent cutting contact. The combination of a 25 mm shank and a 50 mm cutting height reduces vibration during engagement, which translates into improved surface finish and reduced scrap rates. For workshops processing batch work or single components, this stability supports predictable cycle times and repeatable results. Integrated coolant and improved tool life with reliable chip control Integrated internal coolant directs cutting fluid close to the cutting edge, aiding chip evacuation and heat management. This targeted coolant delivery reduces thermal load on the insert and holder, which helps to extend tool life and maintain cutting edge integrity. The result is longer intervals between indexings or insert changes and fewer unplanned stoppages, supporting a smoother production flow and lower operating costs per part. Proven compatibility and practical handling for the shop floor Designed for use with WNMG 0804 indexable inserts, the toolholder is suitable for right-hand turning applications and features an overall length of 250 mm with a nominal 32 mm diameter where applicable. At a weight of 0.911 kg, the bar is robust yet manageable for tool changes and set-up. The ISO designation and compatibility with standard negative-geometry turning inserts simplify procurement and inventory management while ensuring the holder fits established clamping systems. For dependable machining performance from Teknik Makina, contact Metav Werkzeuge for tailored technical advice and fast delivery from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: AP360TM Brand: Teknik Makina ISO designation: A25S PWLNR Compatible inserts: WNMG 0804 Cutting direction: right Internal coolant: yes Core specifications Shank diameter: 25 mm Cutting height: 50 mm Overall length: 250 mm Diameter: 32 mm Weight: 0.911 kg Cutting angle: 95° Materials & features For WNMG 0804 indexable inserts ISO A25S PWLNR holder style Right-hand cutting Internal coolant channel SKU: AP360TM FAQ What inserts fit this boring bar? The boring bar is compatible with WNMG 0804 indexable inserts and is designed to accept standard WNMG geometry for reliable clamping and cutting performance. Is the tool suitable for through-coolant applications? Yes, the holder includes internal coolant, allowing cutting fluid to reach the insert edge directly for better chip control and thermal management. What are the key dimensions and mass of the holder? Key dimensions include a 25 mm shank diameter, 250 mm overall length, 50 mm cutting height and a weight of 0.911 kg; the SKU for reference is AP360TM. Which cutting direction is intended for this toolholder? The toolholder is specified for right-hand cutting operations and is set up accordingly. How does the 95° angle affect machining? A 95° cutting angle increases engagement stability and reduces tool deflection in certain turning operations, contributing to improved surface finish and consistent results. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from through‑coolant performance, a robust 20 mm shank and a 180 mm reach to maintain stable boring cycles and reduced tool wear; order directly via Metav Werkzeuge or ask our technical consultants for tailored advice. KA129TM Boring bar (A16M SDUCR) – SDUC for DC-- indexable inserts, right‑hand, through‑coolant by Teknik Makina The KA129TM boring bar is a right‑hand indexable insert holder designed for precision turning and internal boring, offering through‑coolant capability and a compact shank for stable clamping and reliable chip evacuation. Through‑coolant for improved tool life Compatible with DC-- 11T3 indexable inserts 20 mm shank with 25 mm head diameter 180 mm overall length for deep bores Stable cutting for consistent bore quality The combination of a 20 mm shank and a 25 mm head diameter provides a rigid interface that reduces vibration during machining, resulting in improved roundness and surface finish. This holder’s A16M SDUCR ISO designation ensures straightforward integration with standard tool posts. The documented cutting angle 93° supports controlled engagement of the insert, so each pass delivers repeatable results — an advantage for batch production and quality‑sensitive applications. Coolant delivery that extends tool life Integrated through‑coolant directs cutting fluid precisely to the cutting edge, which aids chip removal and reduces thermal load on the insert. As a result, the indexable inserts run cooler and resist premature wear, improving process uptime. For workshops aiming to lower tooling costs, the improved tool life from effective coolant flow reduces the frequency of insert changes while maintaining machining performance. Designed for straightforward workshop integration With a total length of 180 mm and a compact shank, the holder fits many common tool stations without complex adaptation. The unit is specified for DC-- 11T3 indexable inserts and is configured for right‑hand cutting, allowing quick setup for standard turning and boring tasks. Where machine tool compatibility matters, the ISO designation and standard shank size simplify procurement and spare‑part management across diverse CNC fleets. Practical benefits for production workflows The boring bar’s geometry and internal coolant capability deliver measurable efficiency advantages: fewer interrupted cycles for tool changes and more consistent machining outcomes. The modest weight of the assembly keeps handling easy during tool changes, while the holder’s construct supports controlled chip flow thanks to its right‑hand orientation. These operational improvements contribute to smoother toolroom logistics and predictable production batches. For reliable precision in turning operations trust Teknik Makina’s A16M SDUCR holder — contact Metav Werkzeuge for stock availability and technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: KA129TM Manufacturer: Teknik Makina ISO designation: A16M SDUCR Compatible inserts: DC-- 11T3 Cutting direction: right Through‑coolant: yes Core technical data Shank diameter: 20 mm Cutting height: 32 mm Head diameter: 25 mm Overall length: 180 mm Weight: 0.432 kg Cutting angle: 93° eClass: 21180806 Special features Through‑coolant Right‑hand cutting Indexable insert holder Designed for DC-- 11T3 inserts FAQ Which inserts fit this holder? The KA129TM boring bar is specified for DC-- 11T3 indexable inserts and is supplied in the A16M SDUCR configuration for straightforward mounting of those insert types. Does the holder support through‑coolant machining? Yes, the holder features through‑coolant delivery to the insert area, which improves chip evacuation and reduces thermal stress on the cutting edge. What are the key dimensions to check for machine compatibility? Check the 20 mm shank diameter and the 180 mm overall length when planning tool‑post mounting; the ISO designation A16M SDUCR also assists in confirming fitment. Is the cutting direction suitable for common turning operations? The unit is configured for right‑hand cutting, making it suitable for standard external and internal turning operations where that orientation is required. What advantage does the 93° cutting angle offer? A cutting angle of 93° provides an appropriate approach for controlled engagement and helps achieve consistent surface finish and bore geometry on many workpiece materials. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid, ISO‑compliant holder with internal coolant and left‑hand cutting for reliable chip control; order the KA244TM boring bar directly via Metav Werkzeuge or consult our specialists for application advice. Boring bar KA244TM (A20Q SCLCL) – Left‑hand tool holder with internal coolant by Teknik Cutting Tools A boring bar KA244TM engineered for left‑hand turning operations with internal coolant delivery, designed to accept CC-- 09T3 indexable inserts for stable, efficient machining. Left‑hand cutting direction Internal coolant supply Compatible with CC-- 09T3 inserts Ø25 mm cutting diameter, 180 mm overall Rigidity and repeatable accuracy for stable turning The holder's A20Q SCLCL geometry and compact proportions deliver high rigidity throughout the overhang, supporting consistent cutting conditions and reduced vibration. With a Ø25 mm cutting diameter combined with a 20 mm shank, the tool maintains a stiff connection to the turret, which translates into improved surface finish and predictable tool life. Designed as a standardised turning holder, the component offers familiar mounting dimensions that aid fast setup and repeatability across series production. Effective coolant flow and chip control for longer tool life Integrated internal coolant directs cutting fluid close to the cutting edge, reducing thermal load and flushing chips away from the contact zone. The holder's 95° cutting angle and substantial 40 mm cutting height support efficient engagement with indexable grades, while the coolant path helps maintain cutting insert integrity under higher metal removal rates. The result is extended insert life and fewer interruptions for cleaning or rework, benefiting throughput and process stability. Standardised compatibility to minimise downtime The design accepts CC-- 09T3 indexable inserts and pairs with the conventional clamp size 09, permitting quick insert changes and straightforward inventory management. As an ISO‑pattern holder, the configuration allows interchangeability with common turret adaptors and simplifies procurement of replacement parts. This standard compatibility reduces the need for bespoke tooling and contributes to predictable maintenance cycles in a busy shop environment. Practical dimensions and easy handling in the workshop With an overall length of 180 mm and a measured mass of 0.422 kg, the turning holder balances accessibility and control at the toolpost. The left‑hand orientation is explicitly marked for correct mounting in applications that require negative‑direction cutting, and the shank and holder proportions make it suitable for both short overhang finishing and moderate roughing tasks when paired with the appropriate insert grade. The compact mass also helps reduce centrifugal and inertial effects during rapid indexing sequences. For left‑hand turning with integrated coolant, request the KA244TM by Teknik Cutting Tools through Metav Werkzeuge or contact our Emmerich team for tailored technical guidance. Technical Data Article number: KA244TM Manufacturer: Teknik Makina Designation: Boring bar (SCLC for CC-- Indexable Inserts) ISO designation: A20Q SCLCL Core specifications Cutting diameter: 25 mm Shank diameter: 20 mm Overall length: 180 mm Cutting height: 40 mm Weight: 0.422 kg Cutting angle: 95° Cutting direction: Left Special features Internal coolant supply Compatible with CC-- 09T3 indexable inserts Clamp size: 09 For indexable insert turning operations FAQ Which inserts fit the KA244TM holder? The KA244TM boring bar from Teknik Cutting Tools is designed for CC-- 09T3 indexable inserts, allowing standardised clamping and easy insert replacement. Does the tool provide coolant to the cutting zone? Yes, the KA244TM features internal coolant delivery to the cutting edge, improving heat dissipation and chip evacuation during machining. Is this holder suitable for left‑hand turning operations? The holder is specified for a left cutting direction and is intended for applications requiring negative‑direction turning. What are the key dimensions to check before fitting? Key values for the KA244TM are Ø25 mm cutting diameter, 20 mm shank diameter and 180 mm overall length; weight is 0.422 kg. Which ISO designation and clamp size apply? The tool follows the A20Q SCLCL pattern and uses clamp size 09, compatible with standard turret interfaces. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid design with internal coolant and a 95° cutting angle for consistent insert life and stable boring; order the tooling directly via Metav Werkzeuge or consult their specialists for application-specific advice. KA114TM Drill Bar (A20Q SCLCR) by Teknik Cutting Tools – Internal coolant, 25 mm cutting diameter A robust KA114TM Drill Bar intended for right-hand turning and boring operations with CC-- 09T3 indexable inserts, offering extended reach and coolant-fed cutting for reduced thermal load. Internal coolant for reliable chip evacuation For CC-- 09T3 indexable inserts 25 mm cutting diameter, 180 mm overall length Right-hand cutting; 95° cutting angle Consistent cutting with coolant-fed heat control The bar combines an integrated internal coolant channel with a compact geometry to reduce cutting temperatures and improve chip evacuation. This results in longer insert life and fewer interruptions for edge changes, which in turn supports steady production throughput. The tool’s balanced mass (approx. 0.422 kg) and 180 mm overall length help maintain stable tool runout during medium-reach operations without unnecessary vibration. Precise fit for CC-- insert systems and ISO tooling standards Designed to the A20Q SCLCR ISO designation, the holder accepts CC-- 09T3 indexable inserts and matches established clamping interfaces for fast replacement and repeatable seating. The combination of a 25 mm cutting diameter and a 20 mm shaft provides a compact shank-to-cutting ratio that minimises overhang while preserving accessibility to bores and shoulders. The 95° cutting angle supports effective engagement on the workpiece edge, translating geometry into predictable cutting forces. Built for reliable workshop and production use The holder is optimised for routine turning and boring cycles where quick insert changes and coolant-fed machining increase uptime. The right-hand cutting orientation and sturdy clamping arrangement make the bar suitable for integration into diverse CNC setups and manual lathes that accept ISO-style holders. Lightweight construction with a practical shaft size eases handling during tool setup and storage while maintaining sufficient rigidity for repeatable results. For reliable boring performance from Teknik Cutting Tools, contact Metav Werkzeuge to discuss the KA114TM drill bar and arrange supply from Emmerich; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: KA114TM Brand: Teknik Makina Description: SCLC for CC-- Indexable Inserts ISO designation: A20Q SCLCR Dimensions & core data Cutting diameter: 25 mm Shaft diameter: 20 mm Overall length: 180 mm Cutting height: 40 mm Weight: 0.422 kg Cutting angle: 95° Internal coolant: Yes Features & compatibility For CC-- 09T3 indexable inserts Clamping holder code: 09 Cutting direction: right Suitable for ISO-style insert systems FAQ What insert type fits the KA114TM? The KA114TM drill bar is specified for CC-- 09T3 indexable inserts and is engineered for secure seating and rapid replacement of these inserts. Is the boring bar coolant-fed? Yes, the KA114TM features internal coolant to support chip control and thermal management during continuous cutting. What are the key dimensions to consider for machine setup? Important dimensions include a 25 mm cutting diameter, 20 mm shaft, and 180 mm overall length, which influence reach and clearance in the machine setup. Which cutting direction does this holder use? This holder is configured for right-hand cutting, matching common turning and boring operations that require a right-hand tool path. Does the KA114TM meet ISO tooling standards? The holder is designated A20Q SCLCR, aligning it with common ISO tooling nomenclature for straightforward compatibility with ISO-style clamping and toolholder systems. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a combination of rigidity and coolant-fed design that keeps cycles stable and tool life predictable; compatible with DC-- 11T3 indexable inserts. Order the A20Q SDQCL boring bar directly via Metav Werkzeuge or ask our consultants if needed A20Q SDQCL boring bar by Teknik Makina — left-hand, internal coolant, Ø25 mm head the A20Q SDQCL boring bar is a left-hand toolholder designed for precision boring with DC-- 11T3 indexable inserts, offering integrated coolant supply for improved chip evacuation and stable cutting Left-hand cutting direction Internal coolant supply enabled Compatible with DC-- 11T3 inserts Ø25 mm head, 20 mm shank Stable support for accurate internal boring The toolholder delivers a rigid platform that reduces vibration during internal machining, translating into consistent diameters and surface quality. Its compatibility with indexable inserts such as DC-- 11T3 makes insert changes quick and repeatable, reducing downtime. The A20Q SDQCL designation denotes the ISO-style mounting and geometry, ensuring predictable clamping and reproducible cutting positions across multiple set-ups. Controlled cooling and chip management for longer tool life An integrated internal coolant channel directs lubricant to the cutting edge, improving cooling and aiding chip control in confined bores. This targeted supply helps to dissipate heat, reducing insert wear and the risk of edge build-up. The tool’s cutting angle 107.5° supports favourable chip flow for many typical operations, enabling more consistent cycle times and fewer unscheduled tool changes. Compact geometry for predictable set-up and balance With a Ø25 mm head and 20 mm shank, and an overall length of 180 mm, the boring bar offers a compact footprint that simplifies tool projection planning and balance on the turret. A cutting height of 32 mm ensures correct insert placement and stable cutting engagement, while a modest weight of 0.425 kg aids rapid machine acceleration without sacrificing rigidity. These dimensions make the bar straightforward to integrate into existing toolholding systems. Practical fitment and workshop advantages Designed for indexable insert applications, the bar fits insert type DC-- 11T3 and pairs with clamp-holder designation 11 for secure mounting. The left-hand orientation suits applications where reverse-direction boring is required or where turret layout dictates. For workshops seeking a reliable, coolant-fed solution that streamlines insert changes and maintains repeatable bore quality, this cutter offers a focused, production-friendly option For tailored advice on the Teknik Cutting Tools A20Q SDQCL boring bar and to discuss suitability for specific machines, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: KA278TM Manufacturer: Teknik Makina Dimensions & weight Diameter: 25 mm Shank diameter: 20 mm Overall length: 180 mm Cutting height: 32 mm Weight: 0.425 kg Cutting angle: 107.5° Compatibility & features For indexable inserts: DC-- 11T3 ISO designation: A20Q SDQCL Cutting direction: left Internal coolant: yes Clamp-holder designation: 11 FAQ Which indexable inserts fit the boring bar? The A20Q SDQCL boring bar from Teknik Cutting Tools is designed for DC-- 11T3 inserts and the SDQC style insert pocket Is the tool coolant-fed? Yes, the boring bar includes internal coolant to supply lubricant and improve chip evacuation at the cutting edge What is the cutting direction of this tool? The bar is configured for left-hand cutting direction suitable for applications requiring reverse rotation or specific turret layouts What are the key dimensions to plan for set-up? Key measures: head Ø 25 mm, shank Ø 20 mm, overall length 180 mm, cutting height 32 mm, weight 0.425 kg Which clamp or holder size is required? The tool references clamp-holder designation 11 for correct mount and clamping stability Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of precise geometry and coolant integration for smoother chip control and longer tool life; purchase through Metav Werkzeuge or request tailored advice from our technical consultants. Bohrstange KA260TM A20Q SDUCL – 20 mm shank, internal coolant | Teknik Makina The Bohrstange KA260TM is a left‑hand boring bar designed for SDUC‑style indexable inserts, optimised for precise internal turning and reliable coolant delivery in industrial workshops. Left‑hand cutting, 93° cutting angle Built‑in internal coolant for tool cooling 20 mm shank diameter for secure clamping Compatible with DC-- 11T3 SDUC indexable inserts Consistent chip control and extended tool life The KA260TM boring bar combines a 93° cutting angle with integrated internal coolant to reduce heat at the cutting edge and improve chip evacuation. This configuration lowers the risk of built‑up edge and reduces cycle interruptions, which translates directly into higher productivity and less scrap. The use of SDUC indexable inserts provides repeatable geometry and faster index changes, supporting continuous production runs and simplified maintenance routines. Stable holding and vibration reduction for accurate finishes A 20 mm shank paired with a compact body diameter gives the tool a rigid setup that resists deflection during turning and boring tasks. The overall length 180 mm offers the necessary reach while maintaining stability, which helps to achieve uniform surface finishes and dimensional repeatability. Reduced vibration leads to longer insert life and fewer re‑work cycles, making the tool appropriate for demanding machine‑shop environments. Clear compatibility and practical application guidance Designed for use with DC-- 11T3 inserts in the SDUC format, the bar supports left‑hand cutting applications where the tool must cut when fed from right to left. Internal coolant supports applications that require effective cooling at the insert seat, such as medium to heavy interruption of cut or materials that generate heat. The tool’s configuration makes it suitable for conventional boring and face‑turning operations where indexable insert systems are preferred for rapid re‑conditioning of cutting edges. Contact Metav Werkzeuge for procurement and technical advice on the Teknik Makina KA260TM boring bar, available from our Emmerich warehouse and supported by experienced consultants via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: KA260TM Manufacturer: Teknik Makina ISO designation: A20Q SDUCL Product: Boring bar Variant: SDUC for DC-- indexable inserts Facts Shank diameter: 20 mm Insert height: 32 mm Cutting angle: 93° Cutting direction: left Diameter: 25 mm Overall length: 180 mm Weight: 0.432 kg Internal coolant: yes Special features Compatible inserts: DC-- 11T3 For SDUC indexable inserts Left‑hand cutting geometry Designed for secure clamping (klemmhalter 11) Suited to turning and boring operations FAQ What inserts are compatible with this boring bar? The boring bar KA260TM (Teknik Makina) is specified for DC-- 11T3 inserts in the SDUC format and is intended to be used with SDUC‑style indexable insert systems. Does the tool support internal coolant? Yes, the KA260TM boring bar includes internal coolant delivery to the insert area to aid cooling and chip evacuation during machining. Which cutting direction is this bar designed for? This tool is manufactured with a left‑hand cutting orientation, suitable for operations where the insert cuts while fed from right to left. What clamping and dimensions ensure stability? With a 20 mm shank and a compact diameter, the KA260TM offers a rigid mounting and an overall length of 180 mm that balance reach and stability for accurate finishes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid boring solution that combines internal coolant and a robust 20 mm shank for steady, reproducible bores; ideal for reducing cycle times and tool changes in CNC turning operations. Order supply or request tailored advice via Metav Werkzeuge for seamless delivery from Emmerich. Boring Bar KA222TM (A20Q SVQCR) — internal coolant, 20 mm shank | Teknik Makina Boring Bar KA222TM delivers right‑hand cutting performance for precision internal turning with indexable inserts, suited to standard CNC lathe applications. Internal coolant for improved chip evacuation 20 mm shank diameter for stable clamping Accepts VCMT indexable inserts 30 mm cutting height for deeper cuts Improved rigidity for consistent bore quality The KA222TM is built around a 20 mm shank and a 25 mm diameter body, offering a favourable ratio of rigidity to reach. The ISO designation A20Q SVQCR signals a standardised shank form that ensures secure clamping and minimal deflection during cutting, which translates into consistent bore diameters and reduced rework. With an overall length of 180 mm, the configuration balances accessibility and stiffness for medium‑reach internal turning. These mechanical characteristics provide measurable benefits for production: fewer rejected parts and longer intervals between tool checks, supporting a smoother machining cycle. Cooler cutting, longer insert life Equipped with internal coolant, this tool directs lubricant and coolant precisely to the cutting zone, reducing temperature peaks and improving chip breaking. Compatibility with VCMT indexable inserts and suitability for the common VBMT 1103 format make insert changes straightforward and economical. The 107.5° cutting angle and a 30 mm cutting height are designed to lower cutting forces and distribute loads across the insert face, which helps to extend insert life and maintain surface finish. For shops aiming to raise throughput while keeping tooling costs controlled, the resulting stability and thermal management are decisive operational advantages. Ready for integration into CNC turning processes Configured for right‑hand cutting, this boring solution fits into common lathe toolholders and is simple to implement within existing tool cycles. The tool's mass and balance, indicated by its listed weight of 1.752 kg, support predictable dynamic behaviour during indexing operations. Quick insert indexing and the use of standard insert geometries reduce downtime and simplify inventory management. The KA222TM therefore suits both small batch production and larger series where repeatability and fast changeovers matter. Documentation and ISO‑aligned design mean process engineers can incorporate the bar into fixture plans without specialist adaptation. For a detailed parts match and delivery from our Emmerich warehouse, contact Metav Werkzeuge for a technical consultation on the KA222TM boring bar — telephone +49 2822 7131930 or email info@metav-werkzeuge.com to arrange supply and configuration advice. Technical data Article number: KA222TM Manufacturer: Teknik Makina ISO designation: A20Q SVQCR Product type: SVQC for VCMT indexable inserts Cutting direction: Right Facts Shank diameter: 20 mm Body diameter: 25 mm Cutting height: 30 mm Overall length: 180 mm Weight: 1.752 kg Cutting angle: 107.5° Special features Internal coolant: yes Suitable for VCMT indexable inserts Compatible with VBMT 1103 Right‑hand cutting Designed for CNC lathe boring applications FAQ Which insert types fit this boring bar? The boring bar KA222TM is specified for VCMT indexable inserts and is also listed as suitable for VBMT 1103 inserts, offering flexibility with common insert geometries. Does the tool provide coolant to the cutting zone? Yes — internal coolant is integrated to deliver lubricant directly to the insert and chip root, improving tool life and chip control on the KA222TM. What shank size is required for clamping? The bar uses a 20 mm shank diameter; the ISO designation A20Q SVQCR indicates a standardised shank form for reliable clamping. Is the tool for right‑hand or left‑hand cutting? This model is configured for right‑hand cutting, suitable for standard lathe turning directions. What are the typical applications for this boring bar? The KA222TM is intended for precision internal turning on CNC lathes where indexable inserts, coolant delivery and rigidity are required for repeatable bore quality. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take greater control of internal turning operations by combining reliable clamping and coolant delivery with insert versatility; the integrated internal coolant and compatibility with VCMT 1103 inserts improve chip evacuation and extend insert life. Order the boring bar directly via Metav Werkzeuge or consult the specialists for application advice. Boring Bar KA212TM (A20Q SVUCR) – SVUC holder for VCMT indexable inserts, right‑hand, internal coolant (Teknik Makina) The Boring Bar KA212TM is a right‑hand SVUC turning holder engineered for VCMT 1103 indexable inserts, intended for precision internal machining where rigidity and coolant delivery are essential Right‑hand cutting orientation Internal coolant connection For VCMT 1103 indexable inserts Shaft diameter 20 mm, length 180 mm Greater stability for consistent bore quality The KA212TM is designed to deliver stable cutting performance: a shaft diameter 20 mm and a compact overall profile ensure reduced vibration during internal turning, which in turn supports repeatable diameters and improved surface finish. The holder’s geometry concentrates rigidity close to the cutting edge, so cycle times can be maintained without compromising accuracy. The result is fewer rework cycles and predictable process capability in batch production. Coolant where it counts for longer insert life Internal coolant supply directly to the cutting zone reduces cutting temperatures and supports efficient chip control. With internal coolant routing, the toolholder assists in preventing material build‑up on the insert, prolonging tool life and maintaining consistent cutting forces. This is especially beneficial when machining interrupted cuts or heavier feed conditions, where temperature management translates into lower tooling costs per component. Simple integration with existing turning systems The holder carries the ISO designation A20Q SVUCR and accepts VCMT 1103 inserts, making it compatible with many established tooling setups. The right‑hand orientation aligns with standard lathe configurations for internal turning, while the insert pocket geometry simplifies indexable insert seating and clamping. These features reduce setup time and minimise changeover complexity on CNC lathes. Practical dimensions and handling advantages Measured at a total length 180 mm with a working diameter of 25 mm and weighing 0.689 kg, this boring bar balances accessibility and handling comfort. The design supports straightforward mounting and stable clamping, which benefits everyday workshop use and high‑volume environments alike. Clear identification of the holder type and insert family streamlines tool management and inventory control in a busy toolroom. For reliable supply and application support for the KA212TM from Teknik Makina, contact Metav Werkzeuge in Emmerich: phone +49 2822 7131930 or email info@metav-werkzeuge.com to discuss suitability and delivery options. Technical data Article number: KA212TM Manufacturer: Teknik Makina ISO designation: A20Q SVUCR Designation: SVUC for VCMT Indexable Inserts Cutting direction: right Internal coolant: yes Core dimensions Diameter: 25 mm Shank diameter: 20 mm Cutting height: 32 mm Total length: 180 mm Weight: 0.689 kg Cutting angle: 93° Special features For VCMT 1103 indexable inserts Right‑hand cutting orientation Internal coolant delivery SVUC holder geometry for stable clamping FAQ Which inserts fit this holder? The KA212TM is configured for VCMT 1103 indexable inserts; insert seating and clamp geometry match the SVUC pocket specification. Does the holder provide internal cooling? Yes, the boring bar includes internal coolant delivery to the cutting zone to aid chip evacuation and extend insert life. What are the key dimensions to check for machine compatibility? Check the shaft diameter 20 mm, the outer diameter 25 mm and the total length 180 mm to ensure clearance and collet or chuck compatibility with existing setups. Is this a right‑hand or left‑hand toolholder? The KA212TM is a right‑hand holder, suitable for conventional right‑hand internal turning operations. Teknik Makina: Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a coolant‑fed PCLN design and CNMG 09T3 compatibility for stable, repeatable results in turning and boring operations; order directly via Metav Werkzeuge or consult the specialists for application guidance. AP337TM Boring Bar — PCLN for CNMG indexable inserts with internal coolant (Teknik Makina) The AP337TM Boring Bar is a right‑hand PCLN tool holder engineered for use with CNMG 09T3 indexable inserts, offering internal coolant delivery for improved heat control and chip evacuation in medium‑duty machining. Internal coolant for improved chip evacuation Compatible with CNMG 09T3 inserts Shaft diameter 20 mm for stable clamping 200 mm overall length for extended reach Coolant delivery for consistent machining quality Equipped with internal coolant, this PCLN style boring bar channels lubricant directly to the cutting edge to reduce heat at the tool‑workpiece interface. The targeted coolant supply improves tool life and helps maintain surface finish on longer cycles, while also reducing the risk of built‑up edge. By combining directed cooling with the PCLN geometry, the design supports repeatable machining parameters and more predictable cycle times for series production. Stable clamping and geometry for dimensional accuracy The holder’s 20 mm shaft and 25 mm diameter body provide a rigid connection to the tool post, lowering vibration and enabling tighter tolerances. Its ISO designation A20R PCLNR indicates the right‑hand orientation and standard PCLN pocket for CNMG inserts, while the 95° cutting angle is suited to conventional facing and light boring tasks. The robust construction, together with a low weight of 0.44 kg, balances stiffness with manageable handling during tool changes. Broad insert compatibility and straightforward set‑up Designed for CNMG 09T3 indexable inserts, the tool accepts widely available carbide grades and chipbreakers, simplifying stocking and regrind choices. Fastening interfaces reference a 2.5 mm Allen key, and the holder uses standard locating parts (TA023, TS3, TL3) for secure, reproducible assembly. The component’s 200 mm overall length grants extra reach for recessed features without compromising stability, making the tool suitable for general workshop turning and light production environments. Efficiency and practical benefits for the workshop Using a coolant‑fed PCLN boring bar reduces rework and increases uptime by managing temperatures and chips at the cutting zone; this yields an improved cost‑per‑part ratio in the mid‑term. The combination of standard insert format, accessible clamping, and a compact, stiff shaft supports efficient setup changes and straightforward integration into existing tool‑holding systems from a range of lathes and turning centres. Secure coolant‑assisted machining with Teknik Makina’s AP337TM — contact Metav Werkzeuge for tailored application advice and reliable supply from Emmerich via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: AP337TM Manufacturer: Teknik Cutting Tools / Teknik Makina ISO designation: A20R PCLNR Weight: 0.44 kg Facts Shaft diameter: 20 mm Overall length: 200 mm Body diameter: 25 mm Cutting height: 40 mm Cutting angle: 95° Cutting direction: right Special features Internal coolant Compatible with CNMG 09T3 indexable inserts PCLN pocket style Fastening interface requires 2.5 mm Allen key Locating parts: TA023, TS3, TL3 FAQ What insert type fits this tool? The holder is designed for CNMG 09T3 indexable inserts and accepts standard CNMG geometries for turning and facing applications. Does the bar provide internal coolant delivery? Yes — the AP337TM features internal coolant to direct lubricant to the cutting edge and improve chip evacuation and tool life. Which orientation and ISO designation does the holder use? This tool is a right‑hand unit with the ISO designation A20R PCLNR, compatible with PCLN‑style insert pockets. What are the key dimensions to check for machine compatibility? Relevant dimensions are 20 mm shaft diameter, 25 mm body diameter and 200 mm overall length; the weight is 0.44 kg. What toolpost hardware is referenced for mounting? The holder references locating and fastening parts TA023, TS3, TL3 and uses a 2.5 mm Allen key interface for screw seating. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Benefit from a precise combination of left‑hand orientation, internal coolant and a 20 mm shank for secure clamping and consistent chip evacuation; ideal for turning with WNMG 0604 indexable inserts. Order the tool directly via Metav Werkzeuge or consult the technical team for application advice. A20R PWLNL Boring Bar – PWLN for WNMG 0604, Left‑hand, Internal Coolant (Teknik Makina) The A20R PWLNL is a left‑hand boring bar designed for turning operations with WNMG 0604 indexable inserts, providing stable support and coolant feed directly to the cutting edge Left‑hand orientation for specific turning tasks Internal coolant to the cutting edge 20 mm shank for secure clamping Engineered performance for demanding turning operations The holder is engineered to combine rigidity and accessibility for medium‑duty turning. The 20 mm shank and 25 mm diameter provide a compact but stiff support, reducing vibration when paired with WNMG 0604 inserts. The 95° cutting angle directs forces to a stable contact area so that the insert seat experiences minimal deflection; this improves surface finish and extends insert life. The result is predictable machining behaviour that supports consistent throughput in small to mid‑sized workshops. Stable clamping and predictable chip flow A precise clamp geometry and stable clamping ensure secure retention of the indexable insert, while the integrated internal coolant delivers lubricant and cooling directly to the tool–workpiece interface. This targeted coolant supply reduces heat build‑up, lowers tool wear and helps control chips during interrupted cuts. For setups where left‑hand cutting is required, this configuration supports effective chip evacuation and reduces secondary manual cleaning, increasing net productive time per shift. Designed for efficiency and straightforward maintenance With a 200 mm overall length and 40 mm cutting height, the bar balances reach and stiffness for many lathe applications. The compact mass (approx. 0.471 kg) simplifies tool changes and inventory handling. Maintenance is kept simple because the geometry matches common WNMG 0604 grades, enabling quick insert swaps without special adapters. Fewer tool changes and longer insert life translate into lower cost per finished part and reduced machine idle time. Practical guidance for selection and set‑up Select the A20R PWLNL when a left‑hand holder is required and when WNMG 0604 inserts are the preferred cutting grade for the job. Check machine turret clearance and ensure coolant lines are routed to feed the internal channel. When uncertainty remains about fitment or material suitability, the technical team can advise on insert grade, coolant pressure and optimal cutting parameters to match the application and workpiece material. Contact Metav Werkzeuge today for availability, tailored recommendations and procurement of the A20R PWLNL boring bar; technical advice is available by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: AP390TM Manufacturer: Teknik Makina Facts Shank diameter: 20 mm Cutting height: 40 mm Overall length: 200 mm Diameter: 25 mm Weight: 0.471 kg Cutting angle: 95° Direction: left Compatible inserts: WNMG 0604 Internal coolant: yes Special features ISO designation: A20R PWLNL Clamp holder designation: 06 For indexable inserts: PWLN for WNMG indexable inserts Left‑hand orientation FAQ What insert size is recommended for this holder? The holder is specified for WNMG 0604 indexable inserts; this size matches the seat geometry and cutting height of the A20R PWLNL. Is internal coolant supplied through the tool? Yes. The A20R PWLNL features internal coolant to deliver coolant directly to the cutting zone, improving tool life and chip control. Can this bar be used on standard turret lathes? The bar is suitable for turret lathes that accept a 20 mm shank and left‑hand holders; verify turret clearance for the 200 mm overall length before mounting. What is the cutting direction and why does it matter? This product is designed for left‑hand cutting direction. Correct orientation is essential to ensure proper chip flow and secure clamping during turning. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

A compact adapter offering 25 mm seating and a 20 mm precision bore for stable clamping in production; its 46.5 mm overall length supports tight tool layouts and reliable machining results. Order the adapter directly via Metav Werkzeuge or ask our consultants if needed Adapter for Solid Drills UA10TM — 25 mm seating, 20 mm bore (Teknik Makina) Adapter for Solid Drills UA10TM is a compact mounting adapter for secure integration of solid twist drills into standard toolholders, optimised for precise metalworking applications Secure 25 mm outer diameter seating 20 mm precision bore for solid drills Compact 46.5 mm overall length Durable construction for stable machining Reliable clamping that improves machining consistency The adapter's central function is to provide a precision interface between the toolholder and a solid twist drill. With a 20 mm bore matched to a 25 mm seating, the unit reduces axial and radial play, which in turn lowers runout and enhances surface finish. This mechanical accuracy translates into fewer rejects and longer tool life when paired with calibrated drills and correct machining parameters. The measured dimensions offer a verifiable basis for selecting the correct mounting sleeve and support predictable production outcomes. Space-saving design for compact tooling arrangements A total length of 46.5 mm gives the adapter a short overall footprint without sacrificing engagement depth. The reduced projection is an advantage for machines with limited clearance or multi-tool turrets where collision risk and tool overhang are critical factors. By combining a small envelope with a robust seating diameter, the component contributes to steady cutting conditions and easier tool change integration in busy workstations. The compact form also supports flexible fixturing strategies and minimises vibration potential in constrained setups. Robust interface and straightforward integration in workflows Manufactured to withstand routine shop-floor handling, the adapter features a robust construction that maintains alignment under normal machining loads. As a straightforward mechanical interface, it does not alter the drill's cutting properties but ensures consistent mounting every cycle. The UA10TM is therefore suitable for industrial and workshop environments seeking dependable clamping performance. If suitability or compatibility with a specific toolholder is unclear, Metav’s technical advisors are available to provide tailored guidance and verify fitment against existing tooling inventories. For reliable clamping in machining operations, request a technical consultation for the Teknik Makina Adapter for Solid Drills UA10TM via Metav Werkzeuge — contact our specialists in Emmerich at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to confirm compatibility with specific toolholders and setups Technical data Article number: UA10TM Manufacturer: Teknik Makina ECLASS: 21029216 Facts Outer seating diameter: 25 mm Bore diameter: 20 mm Overall length: 46.5 mm Special features For solid twist drills Compact overall length for tight setups Robust design for stable machining Secure clamping interface FAQ What shank size does the adapter accept? The Teknik Makina Adapter for Solid Drills UA10TM accepts a 20 mm shank via its precision bore while providing a 25 mm seating for the toolholder interface. Will the adapter affect the drill's cutting performance? The UA10TM serves as a mechanical interface; it preserves the drill's cutting characteristics while ensuring consistent mounting, so cutting performance remains driven by the drill grade and machining parameters. How does the adapter reduce runout? Accurate bore and seating dimensions minimise lateral play; the adapter's precise fit improves concentricity between the drill and spindle, which reduces radial runout and improves surface quality. Is the adapter suitable for turreted machines or tight tool arrangements? With an overall length of 46.5 mm, the adapter is designed for compact installations and is well suited to turreted machines and fixtures with limited clearance. Can Metav provide advice on compatibility with existing holders? Guidance on fitment and compatibility is available from Metav; technical confirmation can be provided to ensure the adapter matches the specific toolholder geometry. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a durable combination of precise geometry, secure clamping and compact dimensions that keep cycle times down and tool changes predictable. The tool’s ISO designation and compatibility with VCMT 1103 inserts support straightforward specification and replacement. Order the boring bar directly via Metav Werkzeuge or consult the technical team for application advice. Boring bar SVUC for VCMT indexable inserts — S20Q SVUCR, Ø25 mm, 180 mm length (Teknik Makina) The Boring bar SVUC for VCMT indexable inserts is a right-hand external turning tool designed for secure clamping of VCMT 1103 inserts in medium-duty applications S20Q SVUCR ISO designation For VCMT 1103 indexable inserts Shaft Ø 20 mm Overall length 180 mm Right-hand cutting direction Precision and compatibility for stable external turning The SVUC-style boring bar is engineered to deliver consistent cutting geometry and repeatable results. With the S20Q SVUCR designation it fits established toolholder systems, simplifying procurement and inventory. The combination of a Ø20 mm shaft and a 180 mm overall length balances reach with rigidity, reducing vibration during external turning and improving surface finish. Compatibility with VCMT 1103 indexable inserts means insert changes are fast and standardised, which reduces downtime and keeps production moving. Built for secure clamping and predictable cutting performance A 32 mm cutting height and a 93° cutting angle give this tool a stable centre of cutting action that supports controlled chip formation and predictable tool life. The boring bar’s nominal diameter of 25 mm and a compact mass of 0.432 kg contribute to low overhang-related deflection while remaining easy to handle at the bench. Right-hand cutting direction and the SVUC pocket geometry ensure that standard clamping screws and torque values are compatible with existing toolholders, allowing integration into established turning cycles without process redesign. Clear specification and supply reliability for workshop planning Technical clarity is essential when planning tooling for serial production; the tool’s ISO designation and compatibility statements provide that clarity and make ERP entries straightforward. Files and drawings are supplied where available to support CAM programming and setup. Procurement from a distributor with a European stock base brings added assurance: Metav’s Emmerich hub acts as a quality filter and logistical point, simplifying delivery and replacement planning while enabling consolidated sourcing across measurement and tooling needs. For secure, production-ready external turning with proven SVUC geometry, order through Metav Werkzeuge — Metav’s technical consultants in Emmerich can advise on fitment and supply the required documentation (info@metav-werkzeuge.com | +49 2822 7131930) Technical Data SKU: K212TM Manufacturer: Teknik Makina ISO designation: S20Q SVUCR ECLASS: 21180806 Dimensions and weights Shaft diameter: 20 mm Nominal diameter: 25 mm Cutting height: 32 mm Overall length: 180 mm Weight: 0.432 kg Compatibility and features Suitable for: VCMT 1103 indexable inserts Cutting direction: Right-hand Cutting angle: 93° Clamping designation: 11 (holder reference) FAQ What inserts does this boring bar accept? The boring bar accepts VCMT 1103 indexable inserts; the SVUC pocket geometry is matched to that insert format for reliable clamping and repeatability. Is the tool suitable for high-overhang turning? The combination of Ø20 mm shaft and a 180 mm overall length offers a balance between reach and rigidity; for longer overhangs consider a stiffer holder or reduced cutting parameters. What is the ISO designation and why does it matter? The S20Q SVUCR ISO designation identifies the tool geometry and interface, helping to ensure compatibility with toolholders and simplifying reorder processes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of internal coolant, a 25 mm cutting diameter and a compact 180 mm overall length for stable, repeatable boring cycles; order the bar directly via Metav Werkzeuge or consult the technical team for process integration. Boring bar A20Q — 25 mm, internal coolant — Teknik Makina The Boring bar A20Q is a precision tool for internal cooling-assisted boring applications in machining environments where stable bore geometry and efficient chip evacuation are required. 25 mm cutting diameter Internal coolant supply Overall length 180 mm Right-hand cutting direction Consistent bore geometry through rigid dimensions and angle control The A20Q boring bar is dimensioned to provide stable cutting conditions: a 25 mm cutting diameter combined with a shank diameter 20 mm offers a balance between reach and stiffness for routine bore finishing. The tool’s cutting angle 93° and a cutting height of 32 mm ensure predictable engagement with the insert edge, which in turn reduces vibration and improves surface consistency. Engineers benefit from fewer rework cycles and machines spend more time producing acceptable parts. Improved thermal management with internal coolant An integrated internal coolant channel delivers cutting fluid directly to the cutting zone, which reduces tool-tip temperature and improves lubricity at the insert rake face. This targeted cooling lowers thermal expansion of both tool and workpiece, helping to keep tolerances within specification during longer cutting periods. The coolant provision also assists chip control, decreasing the risk of built-up edge and promoting longer, more reliable tool life. Workshop compatibility and straightforward assembly Designed to common workshop practices, the bar carries an ISO designation A20Q and uses standard screw fixing: Torx T8 for assembly and Torx screw M2.5x6.5 for secure clamping of small components. A clamping head width of 13 mm supports compact clamping systems and facilitates quick replacement routines. The design reduces process downtime and makes the bar easy to integrate into existing toolholders and machining sequences. Production-ready dimensions and handling With an overall length of 180 mm and a weight of 0.69 kg, the bar offers practical handling without compromising on rigidity. The right-hand cutting direction is suited to typical spindle rotations and machining set-ups, allowing the tool to be used in conventional boring cycles. The compact footprint aids in multi-axis operations where clearance is limited, while the balanced geometry supports repeatable set-up and measurement routines at the machine. For machining operations that require targeted coolant delivery and precise bore control, contact Metav Werkzeuge to discuss the A20Q boring bar and receive tailored advice for production integration. Technical data Article number / SKU: KA207TM Brand: Teknik Makina ISO designation: A20Q Core dimensions Diameter: 25 mm Overall length: 180 mm Shank diameter: 20 mm Cutting height: 32 mm Clamping head width: 13 mm Weight: 0.69 kg Cutting direction: right Cutting angle: 93° Features Internal coolant Torx key: T8 Torx screw: M2.5x6.5 Product type: Boring bar FAQ What materials is this boring bar suited for? The A20Q boring bar is specified for general machining tasks; material suitability depends on the chosen insert and cutting data, and the A20Q from Teknik Makina is commonly applied where internal coolant and medium stiffness are required. How is coolant delivered to the cutting edge? Coolant is supplied internally through the bar’s coolant channel, ensuring direct delivery to the cutting zone for the A20Q boring bar (SKU KA207TM), which improves temperature control and chip evacuation. Which clamping interface does the bar require? The bar features a 13 mm clamping head width and uses a Torx T8 engagement with Torx screw M2.5x6.5 for securing auxiliary components and accessories. Is the A20Q suitable for long-reach boring? With an overall length of 180 mm and a shank diameter of 20 mm, the A20Q provides a compromise between reach and rigidity; for extended reach operations, consider bar stiffness versus required tolerance before selection. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid, ISO‑specified holder with internal coolant and precise compatibility for DC-- 11T3 indexable inserts to keep cycle times predictable and tool changes fast; order the boring bar directly via Metav Werkzeuge or ask our consultants if technical advice is required. KA148TM Boring Bar A20Q SDQCR — 20 mm Shank, Internal Coolant (Teknik Makina) A KA148TM is a coolant-fed boring bar designed for stable internal turning with DC-- 11T3 indexable inserts in precision workshop and light-production environments Right-hand cutting orientation Internal coolant supply 20 mm shank diameter Compatible with DC-- 11T3 inserts Stable cutting and repeatable accuracy for production runs The holder is engineered to deliver consistent concentricity, which reduces scrap and rework in batch machining. The A20Q SDQCR designation denotes an established ISO form factor that eases integration with existing toolholders and turret systems. With a solid 20 mm shank and a 25 mm body diameter, the assembly maintains rigidity under cutting loads, translating the bar’s geometry into predictable surface finish and hole tolerances — a tangible time‑saving for repetitive internal turning tasks. Effective cooling and chip control for longer insert life Built‑in internal coolant directs fluid to the cutting zone, improving heat dissipation and aiding chip evacuation. Combined with the 107.5° cutting angle, this encourages favourable chip flow and reduces thermal wear on the insert rake. The result is extended tool life for the indexable inserts and fewer unscheduled tool changes, which supports higher uptime and lower tooling cost per component over extended production periods. Compatibility that simplifies tooling logistics Designed for DC-- 11T3 indexable inserts and referenced as A20Q SDQCR, the boring bar suits common insert sizes and clamping systems used in many workshops. The right‑hand cut orientation is standard for most lathe and turret applications, making the component straightforward to specify across multiple machines. This compatibility reduces the need for bespoke holders and shortens procurement cycles when replacing or upgrading toolsets. Practical dimensions and workshop handling With an overall length of 180 mm and a cutting height of 32 mm, the bar balances reach and stiffness for typical internal turning depths. At 0.425 kg, the unit is light enough for easy handling during set-up yet robust in service. These tangible measurements help production planners and setup personnel assess clearances and tool overhang in CAM programming or manual setup without additional measuring steps. Integration, maintenance and supply assurance The bar’s proven form factor and coolant provision simplify maintenance routines: access to the coolant channel is standardised and insert replacement follows established clamping practice. Choosing an ISO‑specified holder reduces training time for operators and aligns with inventory management best practice. Combined with Metav’s supply reliability from Emmerich, the product supports continuous operation rather than intermittent tooling shortages. Contact Metav Werkzeuge to confirm application suitability for the KA148TM boring bar and to arrange procurement or technical consultation; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: KA148TM Manufacturer: Teknik Makina Product name: Boring bar SDQC for DC-- indexable inserts Facts Shank diameter: 20 mm Cutting height: 32 mm Weight: 0.425 kg Diameter: 25 mm Overall length: 180 mm Cutting angle: 107.5° ECLASS: 21180806 Special features ISO designation: A20Q SDQCR Internal coolant: yes Cutting direction: right For indexable inserts: DC-- 11T3 Clamping holder reference: 11 FAQ What insert type does the bar accept? The KA148TM is designed for DC-- 11T3 indexable inserts and works with standard clamping systems for that insert family. Is coolant supplied through the bar? Yes, the KA148TM features internal coolant to the cutting zone to improve tool life and chip evacuation. What are the key dimensions to check for machine compatibility? Check the 20 mm shank, 180 mm overall length, and 25 mm body diameter against turret and holder clearances when integrating the KA148TM. Which ISO designation applies to this holder? The bar follows the A20Q SDQCR ISO form factor, simplifying replacement and toolholder matching. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of stable 25 mm clamping, compatibility with SCMT 1204 indexable inserts and an extended 250 mm reach for reliable internal turning operations; order the boring bar directly via Metav Werkzeuge or ask our consultants if needed Boring Bar S25S — 25 mm shank, 250 mm overall length | Teknik Makina The boring bar S25S is a precision tool holder for SCMT 1204 indexable inserts, engineered for internal turning tasks in workshop and production environments *25 mm shank diameter for stable clamping *Compatible with SCMT 1204 indexable inserts *Overall length 250 mm for extended reach Precision and stability for repeatable internal turning The design of this tool is focused on rigidity and repeatable results. A 25 mm shank combined with the S25S designation provides a compact yet stiff connection to the machine spindle or tool post, reducing vibration and improving surface finish in bore machining. A 19.5 mm clamping head width helps maintain secure seating of the insert holder, which translates into consistent tool life and fewer reworks. These attributes support higher feed rates and steadier cutting conditions, improving throughput without sacrificing accuracy. Simple insert fitting and secure fastening for quick changeovers Fitted for SCMT 1204 indexable inserts, the holder allows fast replacement of cutting edges without complex setup. The insert is retained with an M5x12 Torx screw tightened using a Torx T20 key, ensuring repeatable clamp force and minimal runout after each index. Indexable inserts offer an economical approach to tool management: when an edge dulls, a quick index or replacement restores cutting geometry without regrinding, lowering per-part tooling costs and simplifying workshop logistics. Extended reach and directed cutting for practical workshop use An overall length of 250 mm provides the reach required for medium-depth bores while keeping the overhang manageable to limit deflection. The tool is configured for right-hand cutting with a modest 3° cutting angle and a 30 mm cutting height, balancing chip formation and stability. At approximately 0.72 kg, the assembly is light enough for straightforward handling yet heavy enough to dampen minor vibrations. Its compact geometry and measured mass make it suitable for conventional and CNC lathes where controlled bore quality and repeatable setups are priorities. For supply enquiries or technical guidance on the Teknik Makina S25S boring bar, contact Metav Werkzeuge in Emmerich for stock information and tailored machining advice via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: K203TM Label: 25mm Boring bar SCMT 1204 L250mm Manufacturer: Teknik Makina Facts Diameter: 25 mm Overall length: 250 mm Weight: 0.72 kg Shank diameter: 25 mm Cutting height: 30 mm Clamping head width: 19.5 mm Cutting direction: right Cutting angle: 3° Torx key: T20 Torx screw: M5x12 Special features Compatible with SCMT 1204 indexable inserts Designation: S25S SKU: K203TM Category: Boring bars eClass: 21180806 FAQ Is the holder suitable for SCMT 1204 inserts? Yes. The boring bar S25S is specifically designed to accept SCMT 1204 indexable inserts and their standard clamping geometry. What cutting direction does the tool support? The tool is configured for right-hand cutting, making it suitable for standard clockwise spindle rotation in turning operations. Which fastening components are required for the insert? The insert is secured with an M5x12 Torx screw requiring a Torx T20 key for tightening and repeatable clamping. How deep can I machine with this tool? With an overall length of 250 mm, the holder provides extended reach for medium-depth bores while maintaining acceptable rigidity for accurate results. Is this tool suitable for CNC and manual lathes? Yes. The combination of a 25 mm shank and compact head geometry suits both CNC and conventional lathes where a stable, repeatable insert clamping system is required. Teknik Makina: Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a 25 mm cutting diameter with an integrated internal coolant channel and a secure 20 mm shank, this configuration delivers improved chip evacuation and steady cutting performance for internal turning tasks; order the KA217TM directly via Metav Werkzeuge or consult our technical advisers for application support. KA217TM A20Q – 25 mm boring bar with internal coolant (Teknik Makina) KA217TM A20Q is a compact boring bar engineered for precision internal turning where coolant supply to the cutting edge and reliable clamping are essential. 25 mm cutting diameter for medium bores Integrated internal coolant for efficient chip removal 180 mm overall length for reach in confined setups 20 mm shank for secure clamping Consistent bore quality through rigid design The combination of a 25 mm outer diameter and a 20 mm shank provides a stable toolholder interface that helps reduce chatter and run-out. A longer reach at 180 mm overall length allows access into deeper bores without sacrificing rigidity. The ISO designation A20Q denotes a standardised geometry that simplifies tool selection in production environments, while the compact mass of 0.422 kg aids manoeuvrability during set-up and minimises spindle load where required. Coolant delivery that protects the insert and improves cycle time The built-in internal coolant channel delivers cutting fluid directly to the cutting zone, which reduces tempering and clears chips efficiently. This targeted lubrication supports longer insert life and lowers the risk of built-up edge, contributing to more consistent surface finishes and potentially shorter downstream finishing operations. Combined with a 107.5° cutting angle, the configuration favours stable chip formation on right-hand cuts and can improve process reliability in repetitive turning cycles. Fast maintenance and secure clamping for uninterrupted production Designed with practical service in mind, the tool uses a Torx T8 key and M2.5x6.5 Torx screw for secure fastening of the adjustable clamping components. The 13 mm clamping width and 30 mm cutting height parameters indicate a robust seating for the cutting geometry, making insert changes straightforward and repeatable. The SKU KA217TM is referenceable for spare parts and ordering, enabling fast replacement of wear items with minimal downtime. Built for workshops and high-mix manufacturing The tool’s right-hand cutting direction and compact footprint make it versatile for both small jobbing shops and larger production cells where space and tool interchangeability matter. Sourcing through Metav Werkzeuge ensures access to a wide stock range and the regional logistics that help maintain a steady supply to European workbenches. If clarification on fitment or machine compatibility is needed, technical consultation is available to match the boring bar to the intended turning set-up. For tailored application advice or to secure delivery of the KA217TM A20Q boring bar from Metav Werkzeuge, contact our consultants at info@metav-werkzeuge.com or call +49 2822 7131930 for rapid, reliable assistance. Technical data Article number: KA217TM Product type: Boring bar ISO designation: A20Q Facts Diameter: 25 mm Overall length: 180 mm Shank diameter: 20 mm Cutting height: 30 mm Clamping width: 13 mm Cutting angle: 107.5° Weight: 0.422 kg Special features Internal coolant Right-hand cutting direction Torx key: T8 Torx screw: M2.5x6.5 SKU: KA217TM Manufacturer: Teknik Makina FAQ What is the primary benefit of the internal coolant on this boring bar? The internal coolant on the KA217TM A20Q supplies fluid directly to the cutting zone, improving chip evacuation and reducing thermal load on the cutting edge for more consistent tool life. Which clamping specifications are relevant when replacing the cutting components? Clamping is configured around a 13 mm clamping width with a Torx T8 fastening system using an M2.5x6.5 screw; these values are integral to safe and repeatable insert changes on the KA217TM. Is the KA217TM suitable for deep-reaching internal turning operations? With an overall length of 180 mm and a 25 mm diameter, the tool provides extended reach while maintaining a 20 mm shank for reliable clamping in many internal turning scenarios. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of solid carbide rigidity, internal coolant, and compatibility with CCMT 09T3 inserts for consistent, high‑precision machining. Order the KE14TM directly via Metav Werkzeuge or ask our consultants for application‑specific guidance. KE14TM Boring bar – SCLC with internal coolant, solid carbide by Teknik Makina The KE14TM boring bar provides a rigid, coolant‑fed solution for external turning operations, optimised for indexable CCMT 09T3 inserts and medium‑to‑heavy machining tasks. Internal coolant for improved chip evacuation Solid carbide construction for high rigidity Accepts CCMT 09T3 indexable inserts 25 mm diameter and 250 mm overall length Stable cutting for repeatable results The KE14TM combines solid carbide construction with a compact geometry to give high stability under load, which reduces vibration and improves surface finish. The tool’s 25 mm cutting diameter and 20 mm shank support precise positioning in the holder, while the monolithic design helps maintain cutting edge alignment over repeated cycles. For operations where dimensional repeatability matters, the increased stiffness translates into fewer reworks and a steadier production flow. Controlled cooling and cleaner chips An integrated internal coolant channel directs cutting fluid directly to the insert seat, lowering cutting temperatures and aiding chip control. This targeted cooling reduces thermal wear on the insert edge and helps maintain consistent cutting conditions during longer passes. The result is improved tool life and a cleaner chip break, which simplifies chip handling and reduces the risk of surface marks on the workpiece when machining demanding materials. Fast setup and insert flexibility for varied tasks Compatibility with CCMT 09T3 indexable inserts allows quick insert changes and a broad choice of grades for different materials. The bar is designed to accept the standard clamping hardware supplied with CCMT‑style inserts; tightening uses a T15 torx key and M3.5x8.5 screw for secure seating. With a 250 mm overall length and a 13 mm cutting height, the tool supports a range of overhangs while remaining easy to handle during tool changes, making it suitable for mixed production environments. For projects that demand coolant-assisted chip control and carbide stiffness, contact Metav Werkzeuge to specify the Teknik Makina KE14TM and receive tailored machining advice from our Emmerich team Technical data Article number: KE14TM ISO designation: E20S SCLCR 09 Brand: Teknik Makina Material: Solid carbide Facts Diameter: 25 mm Overall length: 250 mm Shank diameter: 20 mm Weight: 0.95 kg Cutting height: 13 mm Cutting direction: Right Special features Internal coolant For indexable inserts CCMT 09T3 Torx key: T15 Torx screw: M3.5x8.5 Designation: SCLC with coolant FAQ What is the primary advantage of the internal coolant in this boring bar? The internal coolant in the KE14TM supplies fluid directly to the cutting edge, lowering temperatures, improving chip control and extending insert life for more consistent machining results. Which inserts fit this tool and how does that help production? This bar accepts CCMT 09T3 indexable inserts, allowing rapid insert changes and flexibility in selecting grades for different materials, which reduces downtime and simplifies inventory. Is the KE14TM suitable for heavy cutting or high‑speed applications? The solid carbide construction provides high rigidity that benefits heavy cuts; application suitability for high speeds depends on the chosen insert grade and cutting parameters. How is the insert secured and what tools are required for changeover? Inserts are fastened using an M3.5x8.5 screw tightened with a T15 torx key, enabling straightforward and secure insert replacement on the KE14TM. What length and diameter options are available for this design? This configuration comes with a 25 mm cutting diameter and 250 mm overall length, offering a balance between reach and rigidity for typical external turning tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of precision finishing (0.02 mm), a rigid 25 mm shank and compatibility with CCMT 0602 inserts delivers consistent bore quality and efficient tool changes; order the boring tool directly via Metav Werkzeuge or ask our consultants if needed Boring Tool for Fine Machining — Precision boring holder, CCMT 0602 compatible, Ø25 mm shank by Teknik Makina The Boring Tool for Fine Machining is a precision holder engineered for finishing operations on machined bores; it is optimised for indexable insert turning and compact workshop integration Precision finish tolerance 0.02 mm Compatible with CCMT 0602 inserts 25 mm shank diameter Cutting diameter up to 32 mm Delivering repeatable precision for finishing operations Engineered for fine finishing, this boring holder is specified for a 0.02 mm finish tolerance, which means that consistent bore geometry is achieved with each pass. The tight tolerance is particularly valuable where surface quality and dimensional consistency determine part acceptance. The toolholder design minimises deflection during light cuts and allows predictable machining results, so finishing cycles can be planned with confidence and inspection intervals reduced. The role of indexable tooling is explained by its ability to restore a fresh cutting edge quickly; the use of standardised inserts supports fast reconditioning of the cutting edge. Rigidity and geometry that reduce vibration and improve surface quality A substantial 25 mm shank and an overall length of 156 mm provide the necessary stiffness for finishing bores while keeping overhang controlled. The combination of shank diameter and effective cutting length (shank cutting length 100 mm) reduces chatter and contributes to superior surface finishes. By limiting elastic deflection, the holder supports finer feed settings and lower cutting forces, which translates into improved roundness and a more uniform lay on the machined surface. For workshop planning, this means predictable cycle times and fewer secondary operations. Insert system that speeds up production and simplifies tool logistics The holder accepts CCMT 0602 indexable inserts, a widely available format that allows rapid blade changes and economical rotation of edges. Indexable inserts make it straightforward to switch grades for different materials and to maintain production flow by stocking a limited number of insert grades rather than complete solid tools. The tool supports cutting diameters of up to Ø32 mm, offering flexibility across a range of finishing applications. Lightweight at 0.57 kg, the holder is easy to handle during setup without compromising stability on the machine. Practical integration into workshop and production environments Designed for use on turret lathes and CNC turning centres, this boring holder is targeted at precision job shops and production departments requiring reliable finishing performance. The compact footprint and standard insert interface make it simple to incorporate into existing tool inventories and tool magazines. Inspection results are made more consistent by the holder’s geometry, helping to reduce rework. For customers seeking supply reliability and technical advice, Metav Werkzeuge provides local stock and expertise to support specification and procurement decisions. Contact Metav Werkzeuge in Emmerich for tailored advice on Teknik Makina finishing tools or to arrange a supply; eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data Article number: THKB122TM Manufacturer: Teknik Makina SKU: THKB122TM Facts Fine machining tolerance: 0.02 mm Max cutting diameter: 32 mm Shank diameter: 25 mm Effective cutting length: 100 mm Overall length: 156 mm Weight: 0.57 kg Special features Compatible with CCMT 0602 inserts Designed for fine finishing of bores Indexable-insert holder for fast tool changes FAQ What inserts fit the boring holder? The boring holder accepts CCMT 0602 indexable inserts; this format is compatible with a wide range of grades and geometries for flexible finishing. What accuracy can be expected with this tool? The tool is specified for a 0.02 mm finish tolerance, enabling repeatable bore quality when set up and used under appropriate machining conditions. Which shank size and overall dimensions are provided? The holder features a 25 mm shank diameter and an overall length of 156 mm, with an effective cutting length of 100 mm. What is the maximum cutting diameter for finishing? The holder supports cutting operations up to Ø32 mm, suitable for a variety of finishing bore diameters. Is the Teknik Makina boring tool suitable for automated tool magazines? Yes, the indexable-insert format and compact design allow the Teknik Makina boring tool (SKU THKB122TM) to be integrated into turret and magazine systems where the shank and length match the machine’s toolholders. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid design that delivers fine finishing to 0.02 mm, supports economical indexable inserts and reduces rework in high-precision turning operations; order directly via Metav Werkzeuge for reliable supply and expert advice. Boring tool for fine machining — CCMT 0602 compatible, Ø32 mm by Teknik Makina The Boring tool for fine machining is a precision internal boring bar engineered for tight-tolerance finishing in CNC turning centres and toolroom lathes. Precision fine finishing to 0.02 mm Compatible with CCMT 0602 inserts Ø32 mm max cutting diameter 25 mm shank diameter for stable clamping Consistent fine finishing with minimal rework This boring bar is designed to deliver repeatable surface quality on finishing passes. The specified machining capability of 0.02 mm means that the tool is optimised for close-tolerance internal bore work, reducing the need for secondary operations. Using an indexable insert system such as CCMT 0602 provides cost-effective tool life: worn edges can be indexed or replaced quickly, which keeps machine downtime low and production flow steady. Rigidity and handling that improve process stability A robust 25 mm shank and a 50 mm effective cutting length ensure stable clamping and reduced vibration during machining. The combination of a 25 mm shank, 50 mm cutting length and an overall length of 106 mm gives a compact footprint that improves accessibility in confined bores while maintaining the rigidity required for high-quality finishes. The tool’s 0.402 kg mass contributes to controlled dynamics without adding unnecessary weight to the turret or toolpost. Simple integration into workshop routines The tool accepts common CCMT 0602 indexable inserts, which simplifies procurement and tool management. Compatibility with widely used inserts makes it straightforward to service and replenish consumables. For operations aiming to streamline tooling, this solution aligns with standard insert stocks and shortens changeover times. Metav Werkzeuge’s presence in Emmerich acts as a quality filter and reliable distribution point for Teknik Makina products, supporting uninterrupted workshop supply. For precision finishing with Teknik Makina tools, request the THKB120TM from Metav Werkzeuge — Metav’s specialists in Emmerich can advise on insert selection and delivery: info@metav-werkzeuge.com · +49 2822 7131930 Technical data Article number: THKB120TM Manufacturer: Teknik Makina Product: Boring tool for fine machining Compatible inserts: CCMT 0602 ECLASS: 21041590 Facts Max cutting diameter: 32 mm Shank diameter: 25 mm Cutting length: 50 mm Overall length: 106 mm Fine machining capability: 0.02 mm Weight: 0.402 kg Special features Indexable insert holder for economical use Compact, rigid design for finishing passes Suited to CNC turning centres and toolroom lathes Fast insert change and low downtime FAQ Which inserts fit this boring bar? The THKB120TM accepts CCMT 0602 indexable inserts; Teknik Makina designed the holder to suit this common insert format for ease of procurement and cost-effective indexing. What finish tolerance can be expected? For finishing operations the tool is specified for 0.02 mm capability, enabling tight internal bore control when set up with appropriate feeds and speeds. Is the tool suitable for use in CNC turning centres? Yes — the boring bar is tailored for internal finishing in CNC turning centres and similar machines where stable clamping and short overhangs are achievable. How are inserts replaced on this holder? Inserts for THKB120TM are replaced in the standard manner for indexable systems: secure the tool, remove the clamp screw, replace or index the CCMT 0602 insert, and re-torque to the specified value for reliable clamping. What clamping recommendations apply? Clamp the 25 mm shank securely in the turret or toolholder and minimise overhang to preserve rigidity; the design aims to reduce vibration and maintain surface quality during finishing cuts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of coolant-through operation and compatibility with ADKT 1204 indexable inserts for efficient, low-downtime milling; order via Metav Werkzeuge or consult their specialists for application-specific setup. 25 mm Indexable Milling Cutter S052TM by Teknik Makina — coolant-through, for ADKT 1204 The 25 mm Indexable Milling Cutter S052TM is an insert-mounted cutter designed for versatile face and shoulder milling in industrial workshops and production environments. Coolant-through design for improved chip evacuation Compatible with ADKT 1204 indexable inserts 25 mm shank diameter, 115 mm overall length Three cutting edges for stable material removal Higher productivity through coolant-through cutting The coolant-through configuration delivers coolant directly to the cutting zone, which reduces heat build-up and supports consistent tool life under demanding feed rates. That direct supply improves chip evacuation, helping to avoid chip recutting and to maintain a reliable cutting process. For machining schedules where cycle time and repeatable results matter, this design reduces interruption frequency and supports higher metal removal rates with predictable outcomes. Economical machining with indexable inserts This cutter is built to accept ADKT 1204 indexable inserts, enabling quick insert replacement without regrinding or reclamping the tool body. The indexable system reduces per-cutting-edge cost and shortens machine downtime when inserts are changed. Compatibility with Korloy inserts ensures a broad choice of grades for different materials, so the same cutter body can be adapted from general-purpose steel work to more demanding alloy machining by selecting an appropriate insert grade. Rigidity and precision for consistent surface quality A 25 mm shank and 115 mm overall length deliver a compact, rigid package that minimises deflection in typical milling setups. The three cutting edges provide balanced cutting action and improved stability compared with fewer-edge designs, resulting in lower vibration and a more uniform surface finish. This combination is particularly useful where runout sensitivity and dimensional reproducibility are priorities on batch production runs. Practical assembly and straightforward maintenance Assembly and insert clamping use an M3x7 screw operated with a Torx T8 driver, streamlining maintenance tasks on the shop floor. The cutter’s moderate mass (0.352 kg) makes handling during tool changes straightforward while remaining stout enough for stable cutting. For advice on holders, clamping interfaces or suitable insert grades, Metav’s technical team is available by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to recommend the best configuration for each application. For tailored procurement advice on the Teknik Makina S052TM and its coolant-through advantages, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for prompt, expert support. Technical Data Article number: S052TM Manufacturer: Teknik Cutting Tools Facts Diameter: 25 mm Overall length: 115 mm Shank diameter: 25 mm Cutting length: 40 mm Cutting edges: 3 Weight: 0.352 kg Internal coolant: Yes Special features Compatible inserts: ADKT 1204 Suitable insert maker: Korloy Fixing screw: M3x7 (Torx T8) SKU: S052TM FAQ What inserts fit this cutter? The S052TM accepts ADKT 1204 indexable inserts; Korloy grades are commonly used for this cutter body. Is the cutter equipped for internal cooling? Yes, the cutter features an internal coolant feed (coolant-through) to deliver coolant directly to the cutting zone. Which shank diameter and overall length apply? The cutter has a 25 mm shank and an overall length of 115 mm. How many cutting edges are provided and what is the benefit? The tool runs with three cutting edges, offering balanced cutting, reduced vibration and improved surface quality. What fastener is used to secure the inserts? Inserts are secured with an M3x7 screw operated by a Torx T8 driver. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust milling solution that combines a 25 mm shank for secure clamping, internal coolant for improved thermal control and chip evacuation, and precise seating for ADKT 1706 indexable inserts; order the tool directly via Metav Werkzeuge or contact our consultants for tailored advice. 25 mm Shank Cutter for ADKT 1706 Indexable Inserts — 200 mm, Internal Coolant (Teknik Makina) 25 mm Shank Cutter for ADKT 1706 Indexable Inserts — a milling body engineered to accept ADKT 1706 indexable inserts for stable face and peripheral milling in workshop and CNC environments. Internal coolant channels for improved chip evacuation 25 mm shank for secure clamping and rigidity Compatible with ADKT 1706 Korloy indexable inserts 200 mm overall length for extended reach Improved process stability through rigid shank design A robust 25 mm shank contributes directly to process stability by reducing vibration and deflection during cutting. The solid shank diameter paired with a 200 mm overall length provides a balance between reach and stiffness; this reduces chatter, allows more consistent insert engagement and helps maintain surface finish. For operations where reproducible geometry is essential, the reduced deflection leads to fewer reworks and a steadier cycle time, supporting productivity in small-batch and serial production alike. Cooler running, longer insert life with internal coolant The integrated internal coolant routing delivers cutting fluid directly to the insert pocket and cutting edge, improving heat dissipation and chip control. Targeted coolant flow helps keep cutting temperatures lower, which in turn extends insert life and preserves edge geometry. For indexable systems such as the ADKT 1706 family, controlled coolant reduces the risk of built-up edge and thermal damage, translating into longer service intervals and reduced tooling costs per component. Rapid indexable insert changes and secure fastening This cutter is configured for ADKT 1706 indexable inserts and uses a standard M4x10 Torx screw (Torx T15) for secure, repeatable clamping. The straightforward fastening system minimises changeover time and simplifies setup, which is especially valuable in mixed-production environments. The arrangement supports quick index changes and preserves the precise position of inserts, helping to maintain tolerance control across production runs with minimal downtime. Practical compatibility and workshop integration Designed to accept ADKT 1706 inserts from prominent manufacturers such as Korloy, the milling body fits into standard toolholding systems for 25 mm shank tools. The cutter body’s geometry and insert interface are suitable for a variety of milling tasks where indexable inserts provide cost-effective cutting performance. Clear specification of shank and cutting lengths aids integration into existing tool inventories and CNC setups while ensuring predictable mechanical behaviour. Built for reliable everyday use in professional workshops Manufactured by Teknik Makina, the cutter combines thoughtful mechanical design and practical features such as accessible Torx fastening and coolant provision. The configuration supports routine industrial workflows: stable clamping for accurate passes, reduced thermal loading for insert longevity and quick insert replacement for efficient production scheduling. For procurement and operations teams seeking consistent results, the tool offers a pragmatic balance of functionality and maintainability. Contact Metav Werkzeuge for personalised application advice on the Teknik Makina shank cutter S064TM with internal coolant, or request compatibility checks and spare fastening components by emailing info@metav-werkzeuge.com or calling +49 2822 7131930 Technical Data SKU: S064TM Product type: Shank cutter Manufacturer: Teknik Makina Article designation: Shank cutter for ADKT 1706 indexable inserts Facts Diameter: 25 mm Overall length: 200 mm Shank diameter: 25 mm Cutting length (shank): 35 mm Number of cutting edges: 2 Torx screw: M4x10 Torx key: T15 eClass: 21180806 Special features Internal coolant Compatible with ADKT 1706 indexable inserts Suitable for Korloy ADKT 1706 inserts Compact fastening with Torx T15 FAQ Which insert type fits this cutter? The cutter is prepared for ADKT 1706 indexable inserts; it has the corresponding pocket geometry for this insert family. Does this milling body feature internal coolant? Yes, the Teknik Makina shank cutter S064TM is fitted with internal coolant channels to deliver coolant directly to the cutting zone. What is the shank diameter and overall length? The tool has a 25 mm shank and a 200 mm overall length, offering a compromise between reach and rigidity. Which fastening hardware is used for the inserts? Insert clamping is via M4x10 Torx screws operated with a T15 Torx key, ensuring repeatable and secure seating of ADKT 1706 inserts. Is the cutter compatible with Korloy inserts? Compatibility is specified for Korloy ADKT 1706 indexable inserts; the seating matches the Korloy geometry for that insert type. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com