Gibt es einen Hahn und Kolb Online Shop?

Benefit from the combination of extended reach and fast insert exchange: the 150 mm overall length and compatibility with LNMX 0603 indexable inserts support reliable cycle times and lower per-part tooling costs. Order the shaft milling cutter directly via Metav Werkzeuge or ask our consultants if needed. Shaft milling cutter S287TM — indexable milling cutter Ø32 mm, 150 mm overall length (Teknik Makina) Shaft milling cutter S287TM designed for versatile face and shoulder milling with exchangeable inserts, ideal for industrial production environments Ø32 mm solid shank for stable clamping 150 mm overall length for extended reach Five cutting edges for consistent material removal Compatible with LNMX 0603 indexable inserts Greater stability and consistent machining results The S287TM is built around a substantial Ø32 mm shank and 150 mm overall length, which together deliver enhanced rigidity and an increased working envelope. This combination reduces vibration during heavy cuts and improves surface finish without relying solely on spindle speed. By choosing a tool with a robust shank diameter and balanced length, process planners secure repeatable tolerances and longer uninterrupted runs, translating directly into increased productivity and fewer scrapped parts. Fast insert changes and lower running costs Compatibility with LNMX 0603 indexable inserts, manufactured to widely accepted geometries, enables rapid tool servicing and low inventory complexity. The cutter accepts inserts from Korloy, allowing shops to source cost-effective replacements. Quick clamping is achieved with an M3x7 Torx screw and a T8 key, so downtime for tool changes is minimised. Using indexable inserts reduces consumable expense per cutting edge and provides simple adaptation between roughing and finishing by swapping insert grades rather than whole tools. Integration into machining centres and tooling systems With a 32 mm toolholder interface and standardised mounting dimensions, the milling head fits common toolholders used in production milling centres. The design facilitates secure clamping and consistent concentricity, which supports higher feed rates and longer tool life. Process engineers will value the predictable balance between reach and stiffness, allowing optimisation of step-over and axial depth to meet cycle-time targets while preserving component integrity. Practical operation and workshop benefits The tool’s five cutting edges distribute cutting forces evenly, which can lead to smoother chip evacuation and reduced peak loads on the spindle. Maintenance routines remain straightforward: replacement of LNMX 0603 inserts with the specified M3x7 fastening reduces complexity for floor technicians and shortens setup times. For procurement and production planning, the modular approach simplifies stock keeping and supports a rapid response to changing production mixes. Contact Metav Werkzeuge today for application advice and to secure Teknik Cutting Tools S287TM for your production line — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: S287TM Manufacturer: Teknik Makina eClass: 21180806 ETIM: EC011860 Facts Diameter: 32 mm Shank/holder interface: 32 mm Overall length: 150 mm Number of cutting edges: 5 Special features For LNMX 0603 indexable inserts Compatible with Korloy inserts Torx screw M3x7 Torx key size T8 Indexable milling cutter design FAQ What insert type does the cutter use? The cutter is designed for LNMX 0603 indexable inserts, compatible with common grades and geometries. Is the tool compatible with Korloy inserts? Yes, the tool accepts inserts compatible with Korloy LNMX 0603 types for broad sourcing options. What are the key dimensions for fixture planning? Key dimensions: Ø32 mm diameter, 32 mm shank interface and 150 mm overall length for reach and clamping considerations. Which fastener and key are required for insert clamping? Insert clamping uses an M3x7 Torx screw secured with a T8 key to ensure consistent seating. Can this milling cutter be used for both roughing and finishing? Its indexable design and five cutting edges make it suitable for flexible use; select appropriate insert grades for roughing or finishing tasks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a precise combination of stable multi-edge cutting, simple insert compatibility and compact tool dimensions for uninterrupted production. Order the shank milling cutter directly via Metav Werkzeuge or consult our specialists for application matching. Shank milling cutter S682TM – 32 mm shank, for LOGU 0303 indexable inserts (Teknik Makina) The Shank milling cutter S682TM is engineered as a shank-style milling cutter for LOGU 0303 indexable inserts, intended to provide consistent, repeatable machining performance in setups requiring a compact overall length. 32 mm shank diameter 60 mm effective cutting length Five cutting edges for stable machining Compatible with LOGU 0303 / Kyocera inserts Stable multi-edge cutting for predictable cycle times With five cutting edges, the design reduces chip load per edge and supports a smoother power draw during operation. This configuration promotes a steadier cut profile compared with single-edge tools and contributes to extended tool life under comparable conditions. The combination of a 32 mm shank and the 60 mm effective cutting length keeps the tool rigid in the holder while allowing sufficient reach for many finishing and semi-finishing passes. Emphasis on repeatability makes this cutter especially suitable where process stability and predictable cycle times are key procurement criteria. Quick insert changes and low maintenance effort The cutter accepts LOGU 0303 indexable inserts from Kyocera, enabling fast insert replacement without the need for complex adjustments. Replacement and clamping use a Torx T8 key and M3x7 fixing screws, presenting a straightforward procedure for maintenance teams. Fewer replacement steps reduce downtime between operations and simplify inventory management by relying on widely available insert geometries. The modest overall mass of around 0.412 kg minimises dynamic loads on toolholders during higher spindle speeds, supporting safer and cleaner insert changes. Compact dimensions for space-constrained tool setups An overall length of 150 mm with a 32 mm shank diameter offers a compact footprint that integrates easily into tool magazines and multi-spindle arrangements. The combination of compactness and a standardised interface for LOGU 0303 inserts allows workshop planners to consolidate tooling variants while maintaining the option of high-performance indexable inserts. The SKU S682TM identifies the specific configuration, aiding quick procurement and spare-part matching in purchasing systems. Consistent industrial specification and practical handling Manufactured by Teknik Makina, this shank cutter combines practical handling features with shop-floor compatibility. The cutter’s construction and fixing elements are tailored for routine industrial use, where fast insert seating and mechanical stability matter. Clear specification of the fixing hardware and shank geometry simplifies process planning and reduces uncertainty in tool change procedures. For operations seeking reliability from a compact indexable-cutter solution, the mechanical design supports efficient integration into existing machining cells. Contact Metav Werkzeuge for a technical consultation and component matching — prompt supply and advice from Emmerich are available: info@metav-werkzeuge.com, +49 2822 7131930. Technical data Article number: S682TM Manufacturer: Teknik Makina Core dimensions Diameter: 32 mm Overall length: 150 mm Weight: 0.412 kg Shank diameter: 32 mm Effective cutting length: 60 mm Cutting edges: 5 Special features Compatible with LOGU 0303 indexable inserts Compatible insert manufacturer: Kyocera Torx key: T8 Fixing screw: M3x7 Product type: Shank milling cutter FAQ Which inserts fit this shank milling cutter? The S682TM accepts LOGU 0303 indexable inserts; compatibility with Kyocera-manufactured inserts is specified for straightforward procurement and replacement. How many cutting edges does the tool have and what is the benefit? The cutter has five cutting edges, which distributes chip load and supports smoother cutting action and enhanced stability during machining. What dimensions are critical when setting up the tool in a holder? Key dimensions are the 32 mm shank diameter and 150 mm overall length, with a 60 mm effective cutting length to be considered for holder selection and reach requirements. Which fastener and key are required for insert changes? Insert clamping uses an M3x7 fixing screw tightened with a Torx T8 key, simplifying routine insert replacement and maintenance. How is this tool identified for reorder or spare parts? Order and spare-part enquiries should reference SKU S682TM to ensure the correct shank cutter configuration is supplied. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

High stability and precise shoulder milling are achieved through the combination of a 32 mm shank and a 90° cutting angle, while the three-edge design and 55 mm cutting length enable efficient material removal and deeper reach. Order the S534TM directly via Metav Werkzeuge or consult our specialists for application guidance. S534TM solid shank milling cutter – 32 mm shank for R390-1704 indexable inserts (Teknik Makina) The S534TM is a solid shank milling cutter engineered for use with R390-1704 indexable inserts; designed to deliver square shoulders and reliable toolholding in CNC milling applications where repeatable geometry and accessibility are key 32 mm shank diameter for stable clamping Compatible with R390-1704 Sandvik inserts 3 cutting edges for efficient material removal Total length 200 mm for extended reach Stable clamping and consistent cutting for reliable cycle time Featuring a 32 mm shank and a three-edge configuration, this milling cutter provides a stable interface between spindle and toolholder, reducing chatter and enabling consistent chip formation. The 55 mm cutting length allows for deeper pocketing without compromising rigidity, while the 90° cutting angle produces true square shoulders that simplify finishing passes. These characteristics translate into shorter cycle times and fewer rework operations, offering a measurable efficiency advantage on repeat production runs. Fast indexable insert changes and low maintenance downtime Insert retention is secured with an M3.5x8.5 Torx screw, accessed using a T15 key, which enables straightforward insert replacement and minimal setup interruption. The robust fastening reduces the risk of loosening under load, maintaining positional accuracy of the inserts through long production cycles. At a mass of 0.781 kg, the cutter balances inertial stability with manageable handling during tool setup, supporting safe and efficient workshop routines without elaborate maintenance procedures. Practical reach and versatility in preparation for complex operations With a total length of 200 mm and a diameter of 32 mm, the cutter is suited to reach deeper features while preserving axial stiffness; this makes it a pragmatic choice where access and feature geometry combine to challenge shorter tools. Compatibility with Sandvik R390-1704 indexable inserts allows the use of widely available grades and geometries, facilitating rapid tooling decisions and stock management. Metav’s position as a precision partner ensures that the tool supply is supported by technical advice and a wide product range for complementary tooling needs For precision milling with reliable repeatability, request the Teknik Makina S534TM via Metav Werkzeuge or contact our specialists at info@metav-werkzeuge.com / +49 2822 7131930 for tailored application advice and compatibility checks Technical data SKU: S534TM Manufacturer: Teknik Makina Suitable for indexable inserts: R390-1704 Torx screw: M3.5x8.5 Torx key: T15 Weight: 0.781 kg Core measurements Shank diameter: 32 mm Cutting length: 55 mm Number of cutting edges: 3 Total length: 200 mm Diameter: 32 mm Cutting angle: 90° Special features Compatible with Sandvik R390-1704 indexable inserts Three-indexable-insert configuration Solid shank design for increased stiffness Brand: Teknik Makina SKU reference: S534TM FAQ What inserts are compatible with this cutter? The S534TM is designed for use with R390-1704 indexable inserts and is specified as compatible with Sandvik insert types of that designation. How is each insert secured? Inserts are fastened with an M3.5x8.5 Torx screw; the recommended key for tightening and removal is a T15. What machining geometry does the cutter provide? The tool features a 90° cutting angle, which produces square shoulders ideal for finishing and achieving precise corner geometry. Is the tool suitable for deep pocketing? Yes. The combination of a 55 mm cutting length and a 200 mm overall length gives the cutter the reach needed for deeper pockets while retaining axial stiffness. Which brand manufactures the tool and what is the SKU? The tool is produced by Teknik Makina and is listed under SKU S534TM for ordering and inventory reference. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a 32 mm shank with a 60 mm cutting length and compatibility with Sandvik R390‑1806 indexable inserts provides high material‑removal capacity with repeatable set‑up and straightforward maintenance — order directly via Metav Werkzeuge or consult our technical advisers for application support. Schaftfräser S601TM — indexable insert milling cutter, 32 mm shank, 3 flutes (Teknik Makina) The Schaftfräser S601TM is an indexable shank milling cutter designed for use with R390‑1806 Sandvik inserts, suited to medium and heavy milling tasks where quick insert changes and stable clamping are priorities. 32 mm shank diameter for stable clamping 60 mm effective cutting length 3 cutting edges for high material removal Compatible with Sandvik R390‑1806 inserts Optimised cutting performance for increased throughput High mechanical stability is delivered by the 32 mm shank and a rigid tool body, enabling more aggressive passes without compromising workpiece accuracy. With three cutting edges and a 60 mm cutting length, the tool supports elevated material‑removal rates while maintaining predictable chip formation. The 90° cutting geometry produces clean shoulder surfaces and reduces the need for secondary finishing, so cycle times are shortened and overall process efficiency improves. This technical setup is especially advantageous where replacement inserts offer a lower cost per cut compared with solid‑carbide alternatives. Secure clamping and rapid insert serviceability Assembly and reconditioning were prioritised in the design: insert fixation uses an M4x11 Torx screw tightened with a T15 key, providing consistent clamp force and fast insert changes. The indexable concept means damaged or worn cutting edges are replaced in seconds, restoring cutting geometry without regrinding the holder. Repeatable mounting reduces set‑up deviations and ensures that each insert position provides reliable cutting performance. The combination of precise screw fastening and standardised R390‑1806 insert format simplifies stock management and reduces tooling downtime. Practical integration into workshop workflows At an overall length of 200 mm and a weight of 1.188 kg, the holder balances rigidity with manageable handling during tool changes and machine loading. Compatibility with widely used Sandvik R390‑1806 inserts makes the tool an economical choice for workshops seeking standardised consumables and predictable tool life. By replacing only the insert, running costs fall and inventory efficiency rises; the result is a more predictable production schedule and lower per‑part tooling expense. The design supports straightforward measuring and inspection routines, helping maintain process control across batch runs. For robust, indexable milling performance with proven compatibility, contact Metav Werkzeuge to discuss specification matching or to place an order — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: S601TM Manufacturer: Teknik Makina Compatible inserts: R390‑1806 Compatible insert manufacturer: Sandvik Torx screw: M4x11 Torx key: T15 Core data Shank diameter: 32 mm Effective cutting length: 60 mm Number of cutting edges: 3 Overall length: 200 mm Diameter: 32 mm Cutting angle: 90° Weight: 1.188 kg Special features Indexable insert system Designed for R390‑1806 inserts Quick‑change insert fastening with Torx screw 3‑flute configuration for high MRR FAQ What insert type does this milling cutter use? The S601TM holder accepts R390‑1806 indexable inserts, a common format that simplifies spare‑part stocking. How is the insert fixed to the tool? Insert clamping is achieved with an M4x11 Torx screw, tightened using a T15 key for secure and repeatable fixation. What is the shank diameter and how does it affect stability? A 32 mm shank diameter gives the holder greater rigidity during heavy cuts, improving stability and surface finish. How many cutting edges are active and what is the benefit? The tool has three cutting edges, which balances material removal and chip control while extending time between indexings. Is the holder suitable for quick insert changes on the shop floor? Yes — the indexable design and Torx‑screw fastening enable fast insert replacement to minimise machine downtime. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a robust Ø32 mm cutting diameter with a stable shank Ø25 mm and three cutting edges, the tool delivers consistent material removal and reduced downtime; order the R194TM shank milling cutter through Metav Werkzeuge or request application guidance from their specialists. Shank milling cutter R194TM — for RDMT 1003 indexable inserts, Ø32 mm, 3‑edge by Teknik Makina The Shank milling cutter R194TM is an indexable insert milling tool engineered for precision face and slot milling with RDMT 1003 inserts in industrial CNC and workshop environments. Accepts RDMT 1003 indexable inserts Ø32 mm cutting diameter 3 cutting edges for smooth removal Shank Ø25 mm, 40 mm cutting length High-performance compatibility that boosts throughput The R194TM is built around compatibility with RDMT 1003 indexable inserts, which makes it straightforward to maintain cutting performance while keeping tooling costs under control. Using indexable inserts avoids full-tool replacement and shortens setup times; this yields measurable productivity gains on repeated operations. The Ø32 mm cutting diameter provides a balance between material removal rate and surface finish, while the design supports reliable chip control during continuous milling cycles. Robust shank and compact geometry for stable cuts A shank Ø25 mm combined with a 40 mm cutting length and 120 mm overall length gives the cutter a rigid footprint that resists vibration at moderate spindle speeds. The reduced tool deflection improves dimensional consistency across batches and contributes to longer insert life. With a tool weight of 0.484 kg, the assembly remains manageable for standard toolholders yet heavy enough to dampen chatter in common machining setups, supporting repeatable results without complex fixturing. Secure clamping and service-friendly insert changes Clamping is executed using the M3.5 locking screw and an M3.5x8.5 Torx screw; the required hex driver is T15, ensuring secure fastening of the insert pocket. The three cutting edges are indexed quickly, allowing a fast return to production after a wear change. These mechanical details reduce the risk of misalignment during replacement and simplify routine servicing, making the cutter suitable for high-turnover production cells and maintenance-friendly workshops. Workshop advantages and practical handling As an indexable-insert solution, the cutter minimises inventory overhead by separating the body from the cutting tips; spare inserts are compact to store and simple to swap. The modular approach supports consistent tool performance across shifts and operators, and the clear specification of fastening hardware reduces assembly mistakes. Overall, this tool is designed to integrate with existing insert workflows and to provide dependable results for recurring milling tasks. Contact Metav Werkzeuge today for tailored cutting data and to arrange supply of the R194TM insert shank cutter for RDMT 1003 applications Technical data Article number: R194TM Manufacturer: Teknik Makina Product: Shank milling cutter for RDMT 1003 indexable inserts Facts Diameter: 32 mm Shank diameter: 25 mm Cutting length: 40 mm Overall length: 120 mm Cutting edges: 3 Weight: 0.484 kg Locking screw: M3.5 Torx screw: M3.5x8.5 Torx key: T15 Special features Compatible with RDMT 1003 indexable inserts Robust shank design for reduced vibration Indexable three-edge configuration for efficient stock removal FAQ Which insert type fits this cutter? The R194TM accepts RDMT 1003 indexable inserts designed for the cutter body and provides reliable seating and rotation for each index. What are the main dimensions to check for toolholder compatibility? Check the Ø32 mm cutter diameter and shank Ø25 mm to ensure the toolholder and spindle collet match the R194TM's geometry. How many cutting edges are used and what is the benefit? The cutter uses 3 cutting edges, which balance chip load and feed per tooth for smoother material removal and consistent surface quality. Which fastening hardware is required for insert clamping? Insert clamping uses a M3.5 locking screw and an M3.5x8.5 Torx screw; the supplied driver size is T15 for secure tightening. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, indexable milling solution that combines robust clamping, precise dimensions and simple insert replacement for steady production. Benefit from the Ø32 mm cutting diameter with three cutting edges and a 25 mm shank for reliable spindle engagement — order the tool directly via Metav Werkzeuge or consult the team for application advice. Shank cutter for RDMT 12T3 indexable inserts — Ø32 mm, 3 cutting edges (Teknik Makina) The shank cutter is a purpose-built milling tool for efficient face and slot milling with RDMT 12T3 indexable inserts, suitable for general machining setups requiring straightforward insert changes and secure clamping. Ø32 mm cutting diameter Three cutting edges for balanced cutting 25 mm shank for solid spindle fit 40 mm effective cutting length Rigidity and stable metal removal for consistent component quality This milling tool delivers dependable rigidity through its defined dimensions: a 32 mm cutting diameter combined with a 25 mm shank ensures stable spindle seating and reduced vibration during operation. The tool’s three cutting edges distribute cutting forces evenly, which aids in maintaining surface finish and extending insert life under comparable cutting conditions. The specified overall length of 120 mm and a cutting length of 40 mm provide a balanced reach-to-stiffness ratio, making the tool suitable for face milling and shallow slotting tasks where maintaining dimensional accuracy across multiple parts is essential. The declared weight of 0.473 kg reflects a compact design that is easy to handle during tool changes without compromising on mechanical integrity. Quick, repeatable insert replacement and secure fastening Designed around RDMT 12T3 indexable inserts, the tool simplifies maintenance and keeps downtime to a minimum. Insert retention uses a M3.5 locking screw and M3.5x8.5 Torx screw, tightened with a T15 Torx key, enabling repeatable clamping torque and safe seating of each insert. This straightforward fastening concept reduces variability in tool set-up and supports consistent cutting geometry after every insert change. The clear specification of the fastening hardware supports maintenance planning and spare part stocking, while the standardised insert interface helps to streamline inventory when using common RDMT 12T3 inserts across several toolholders. Versatility for workshop workflows and integration in production The tool’s compatibility with RDMT 12T3 inserts and its compact shank make it a flexible choice for diverse workshop machines, including those with limited toolroom space. The combination of a defined Ø32 mm diameter and a 25 mm shank supports a wide range of spindle tapers and collet systems commonly found in milling machines and machining centres. For buyers seeking operational continuity, the simple insert system and standard Torx fixation allow technicians to perform rapid swaps and keep production running. If further clarification on machine compatibility or recommended cutting parameters is required, technical guidance is available to ensure the tool is applied where it brings the most benefit. Select Teknik Makina’s shank cutter for dependable indexable milling — contact Metav Werkzeuge for order placement or tailored technical advice from Emmerich today Technical data Article number: R230TM Manufacturer: Teknik Makina Designation: Shank cutter for RDMT 12T3 indexable inserts ECLASS: 21180806 ETIM: EC011860 Core dimensions Cutting diameter: 32 mm Number of cutting edges: 3 Shank diameter: 25 mm Cutting length: 40 mm Overall length: 120 mm Weight: 0.473 kg Fixings & compatibility For RDMT 12T3 indexable inserts Locking screw: M3,5 Torx screw: M3,5x8,5 Torx key: T15 Files: 62de7e4d148ec6b71020ff8a, 62de7ee40f56dbb4de4dbf56 FAQ Which insert type is compatible with this tool? The tool is designed for RDMT 12T3 indexable inserts; RDMT 12T3 inserts seat correctly in the cutter and provide the specified cutting geometry. What are the key dimensions to check for machine compatibility? Confirm spindle and collet acceptance for a 25 mm shank, and ensure the machine can accommodate an overall length of 120 mm and a 32 mm cutting diameter. How are inserts secured and what tools are required? Inserts are secured with a M3,5 locking screw and a M3,5x8,5 Torx screw, tightened using a T15 Torx key for repeatable clamping. Can the cutter be used for both face milling and slotting? Yes; the combination of 40 mm cutting length and three cutting edges makes the tool suitable for controlled face milling and shallow slotting operations. What is the article number for ordering or inventory? The article number (SKU) is R230TM, listed for ordering and stock control. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust build quality, rapid insert replacement and extended reach for reliable milling operations; the tool’s 32 mm shank, compatibility with RDMT 12T3 inserts and 300 mm overall length ensure stable performance in demanding setups. Order the R256TM directly via Metav Werkzeuge or consult the Metav team for application advice. Schaftfräser R256TM — shank milling cutter for RDMT 12T3 indexable inserts, 32 mm shank by Teknik Makina The Schaftfräser R256TM is a purpose-built shank milling cutter for indexable RDMT 12T3 inserts, engineered for operations requiring stability and extended reach in machining environments 32 mm shank for stable clamping Compatible with RDMT 12T3 indexable inserts Three cutting edges for balanced performance 300 mm overall length for extended reach Stability and precision for consistent results A thick 32 mm shank and balanced mass distribution provide reduced vibration and improved positional stability during milling. The configuration with three cutting edges delivers consistent chip removal and a predictable load per cutter tooth, which helps to maintain surface quality and repeatability across batches. The presence of an M3.5 locking screw and a dedicated T15 Torx key simplifies secure clamping of the insert seat, focusing maintenance time on quick insert changes rather than alignment work. Fast insert changes to keep production moving Compatibility with RDMT 12T3 indexable inserts means replacement is straightforward and predictable. The specified M3.5x8.5 Torx screw secures each insert reliably while allowing rapid replacement with a standard T15 driver, reducing machine downtime and supporting efficient tool management. The modular insert system makes it economical to rotate or replace cutting edges when wear occurs, extending the usable service life of the toolholder and lowering per-part machining costs. Extended reach without compromising rigidity With a 300 mm overall length combined with a 70 mm cutting length, the cutter is designed for tasks that require deeper access while maintaining rigidity. The tool’s mass—approximately 1.829 kg—contributes to dampening during cutting, which in turn helps to reduce chatter when working at longer overhangs. This balance between reach and stability supports machining of components with recessed features or extended flanks without compromising on surface finish. Durable, service-friendly design for workshop workflows Constructed for industrial use and straightforward upkeep, the R256TM allows quick replacement of worn components and uses standard fastening hardware for service simplicity. The indexable system reduces waste compared with disposable solid tools, while the organiser-friendly spare-part logic shortens tool change intervals. Supplied by Teknik Cutting Tools and distributed via Metav Werkzeuge, the tool benefits from reliable availability and a technical supply chain geared to professional workshops and production facilities. For personalised tooling advice, application matching or to secure the R256TM through Metav Werkzeuge, contact Metav Werkzeuge GmbH at +49 2822 7131930 or info@metav-werkzeuge.com to discuss specifications and compatible inserts Technical data Article number: R256TM Manufacturer: Teknik Makina Designation: Schaftfräser for RDMT 12T3 Indexable Inserts Facts Shank diameter: 32 mm Cutting length: 70 mm Overall length: 300 mm Weight: 1.829 kg Number of cutting edges: 3 Special features Compatible with RDMT 12T3 indexable inserts Locking screw: M3,5 Torx screw: M3,5x8,5 Torx key: T15 FAQ What inserts fit this cutter? The cutter accepts RDMT 12T3 indexable inserts; the clamping is secured with an M3,5 locking screw and M3,5x8,5 Torx screw as specified for the R256TM. How is the insert fixed and removed? Inserts are fastened with the M3,5x8,5 Torx screw; removal and fitting require a T15 Torx key for safe and repeatable mounting. Is the tool suitable for deep internal features? Yes. The 300 mm overall length and 70 mm cutting length make the tool suitable for operations requiring extended reach while maintaining acceptable rigidity. How many cutting edges are available and what is the benefit? The tool has three cutting edges, which provides a balanced cutting load per tooth and contributes to smoother chip evacuation and steady cutting forces. Can the cutter be serviced in a standard workshop? Routine service—insert changes, screw checks and quick inspections—can be carried out with standard workshop tools, including a T15 Torx driver. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a stable 32 mm shank and a 60 mm effective cutting length to increase process reliability and reduce vibration during indexable insert milling; combine robust clamping with compatibility for SDMT 09T3 inserts for consistent chip control. Order directly via Metav Werkzeuge or consult the Metav team for application-specific setup. Indexable Insert Milling Cutter S396TM — 32 mm shank, for SDMT 09T3 inserts (Teknik Makina) Indexable Insert Milling Cutter S396TM is a modular tool designed for machining tasks with SDMT 09T3 indexable inserts, providing a robust shank and secure insert clamping for stable cutting performance in production environments Compatible with SDMT 09T3 indexable inserts 32 mm shank for stable clamping 60 mm effective cutting length Torx screw M3.5x8.5, T15 key required Greater stability for predictable machining results The solid 32 mm shank ensures a rigid connection between spindle and cutter, significantly reducing chatter and deflection during side and face milling. This mechanical stability directly translates into consistent surface finish and longer insert life, since reduced vibration lowers insert wear. For workshops seeking measurable productivity gains, the robust shank geometry supports higher feed rates and steadier tolerances, making the tool a practical choice for repetitive production runs where process repeatability is crucial. Precise insert system for fast indexability and chip control Designed to accept SDMT 09T3 indexable inserts, this cutter provides a system-oriented solution for rapid insert changes and predictable cutting behaviour. The combination of a fixed insert pocket geometry and the specified M3.5x8.5 Torx screw with T15 drive secures the insert reliably, preserving alignment under load. Fewer manual adjustments mean shorter downtime for tool changes and a quicker return to full cutting parameters, which benefits throughput on medium‑ to high‑volume components. Practical dimensions tailored to workshop workflows With a 60 mm cutting length, three cutting edges and a total length of 150 mm, the S396TM balances reach and rigidity for a range of milling operations. The three-flute arrangement promotes efficient chip evacuation while maintaining cutting stability, so operations that require moderate axial engagement see improved cycle consistency. Weighing 0.934 kg, the assembly is substantial enough for damping vibrations yet compact for standard toolholders. Compatibility with ZCC insert options expands selection flexibility for different grades and coatings, allowing process optimisation without changing toolholders. For a reliable, production-ready insert milling solution from Teknik Makina, contact Metav Werkzeuge to discuss the S396TM and its fit for specific applications — email info@metav-werkzeuge.com or call +49 2822 7131930 to arrange supply from Emmerich. Technical data Article number: S396TM Brand: Teknik Makina Suitable for indexable inserts: SDMT 09T3 Compatible insert manufacturer: ZCC Core dimensions Shank diameter: 32 mm Cutting length (shank cutting length): 60 mm Number of cutting edges: 3 Total length: 150 mm Diameter: 32 mm Weight: 0.934 kg Features and compatibility Torx screw: M3.5x8.5 Torx key: T15 For SDMT 09T3 indexable inserts SKU: S396TM FAQ Which inserts fit this cutter? The cutter accepts SDMT 09T3 indexable inserts; the design is compatible with inserts from ZCC and other suppliers offering the SDMT 09T3 geometry. What are the key dimensions to check for fixture compatibility? Check the 32 mm shank diameter, 150 mm total length and the 60 mm effective cutting length to ensure proper toolholder engagement and adequate clearance in the machine setup. How is the insert secured? Inserts are clamped with an M3.5x8.5 Torx screw; a T15 drive is specified for correct torque and secure seating. How many cutting edges does the tool have and what is the benefit? The tool has three cutting edges; this offers a compromise between smooth cutting action and efficient chip evacuation for many milling tasks. What is the SKU and brand for ordering? The product is sold as S396TM by Teknik Makina; reference this SKU when specifying the cutter for procurement or spare parts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of sturdy clamping, targeted cooling and straightforward insert compatibility for reliable milling results; order the tool directly via Metav Werkzeuge or consult our specialists for integration advice. Insert milling cutter S794TM — 32 mm shank, internal coolant, for SOET 13 indexable inserts (Teknik Makina) Insert milling cutter S794TM designed for indexable SOET 13 inserts, offering a compact 32 mm shank and 180 mm overall length for machining tasks that demand stability and coolant-fed cutting performance 32 mm shank for secure clamping Internal coolant for improved chip control Compatible with SOET 13 inserts (Palbit) 180 mm overall length for extended reach Stable clamping for repeatable accuracy This insert milling cutter is engineered around a 32 mm shank, delivering notable rigidity at the tool interface and helping to reduce vibration during side and face milling. The robust shank dimension supports consistent clamping, which in turn improves surface finish and prolongs tool life compared with smaller-diameter holders. For production environments where repeatability matters, the combination of a substantial shank and a well balanced cutter body contributes directly to predictable cycle times and fewer reworks. Effective cooling to extend tool life Equipped with internal coolant, the cutter routes cutting fluid directly to the cutting zone to aid chip evacuation and temperature control. This feature reduces thermal load on the cutting edges, supporting longer edge life and improved process stability when using indexable inserts. In practice, targeted coolant flow helps to prevent built-up edge on the insert and maintains geometric integrity of the cutting edge, making the tooling choice particularly suitable for continuous or semi-continuous milling operations. Practical design for quick insert changes and maintenance The tool accepts SOET 13 indexable inserts and is specified for inserts from Palbit, allowing straightforward procurement and replacement in mixed-tool inventories. The head uses M4x10 Torx screws secured with a T15 key, simplifying service procedures and minimising downtime. With three cutting edges and a 60 mm cutting length, the package balances capacity and serviceability for many standard milling tasks; replacement inserts can be changed rapidly, returning the cutter to production with minimal handling. Contact Metav Werkzeuge for tailored integration advice on the Teknik Makina S794TM with internal coolant — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss tooling setups and compatibility with existing fixtures Technical data Article number: S794TM Product type: Insert milling cutter Manufacturer: Teknik Makina Core technical data Diameter: 32 mm Overall length: 180 mm Weight: 0.956 kg Shank diameter: 32 mm Cutting length: 60 mm Number of cutting edges: 3 Special features Internal coolant Compatible with SOET 13 indexable inserts Compatible inserts manufacturer: Palbit Torx key: T15 Torx screw: M4x10 FAQ Which inserts fit this cutter? The cutter is designed for SOET 13 indexable inserts and is compatible with inserts supplied by Palbit; use the corresponding SOET 13 geometry for correct seating and cutting performance. What is the purpose of the internal coolant? Internal coolant delivers fluid directly to the cutting zone on the S794TM, improving chip evacuation and temperature control to extend insert life and maintain process stability. How many cutting edges does the tool have? The tool features three cutting edges, balancing material removal rate with vibration control and providing a practical compromise between feed per tooth and cutting stability. Which screw and key are required for insert replacement? Insert clamping is secured with M4x10 Torx screws requiring a T15 key for safe and efficient replacement. Is the shank suitable for rigid clamping systems? The 32 mm shank offers a sturdy interface for standard tool holders and rigid clamping systems, helping to reduce deflection and improve repeatability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining the 32 mm shank for stable clamping, five cutting edges for efficient material removal and a secure Torx fixing, the cutter delivers repeatable performance across production runs. Benefit from quick insert changes with WNGX 0403-compatible tooling and order the S946TM directly via Metav Werkzeuge or consult our specialists for setup advice. Indexable shank cutter S946TM — 32 mm shank, 5 cutting edges by Teknik Makina A robust indexable shank cutter S946TM engineered for machining with WNGX 0403 indexable inserts, offering a compact 110 mm overall length for stable rotary performance. For WNGX 0403 indexable inserts Shank diameter 32 mm for stable clamping Five cutting edges for efficient material removal Torx fixing M2.5x5.5, T8 key Increased rigidity and consistent removal rates for production work The combination of a 32 mm shank and a compact 110 mm overall length provides enhanced rigidity at the toolholder, which translates into consistent chip formation and reduced vibration during milling. With five cutting edges, material is removed more evenly per revolution, reducing cycle time on repetitive tasks. Compatibility with the WNGX 0403 insert family ensures ready availability of replacements and allows easy adjustment of cutting geometry without changing the whole tool. The S946TM is therefore suited to workflows that prioritise throughput and reproducible surface finishes. Fast indexable changes and secure clamping to minimise downtime Indexable tooling simplifies maintenance and lowers per-edge cost compared with monolithic cutters. The cutter uses a Torx M2.5x5.5 fixing screw tightened with a T8 key, giving a reliable and repeatable clamp force for each insert change. Quick, repeatable replacement of WNGX 0403 inserts reduces machine idle time and simplifies inventory control: one set of inserts can service multiple cutters. The modular approach supports both ad hoc repairs on the shop floor and planned tool-life strategies in CNC machining centres. Practical fit for workshops and machining centres seeking dependable tooling Designed by Teknik Makina for industrial use, this cutter pairs robust mechanical design with the flexibility of indexable inserts, making it appropriate for general milling operations where changeover speed and tool stability are priorities. The tool’s geometry and five-edge configuration favour steady production cycles, while the standardised fixing method eases operator training and toolroom logistics. Where consistent throughput and straightforward maintenance are required, this indexable shank cutter delivers measurable operational advantages. Contact Metav Werkzeuge to discuss suitability for specific applications, request batch availability or arrange technical guidance from our Emmerich team via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: S946TM Manufacturer: Teknik Makina SKU: S946TM Facts Shank diameter: 32 mm Diameter: 32 mm Overall length: 110 mm Cutting edges: 5 Special features Compatible inserts: WNGX 0403 Compatible insert manufacturer: Korloy Fixing screw: M2.5x5.5 (Torx) Torx key: T8 Designed for indexable insert tooling FAQ What inserts fit this cutter? The cutter accepts WNGX 0403 indexable inserts; most standard WNGX 0403 grades from Korloy are compatible with the S946TM. How is the insert secured? Inserts are clamped using a Torx M2.5x5.5 screw tightened with a T8 key, which provides repeatable and secure fixing on the S946TM. Is the shank suitable for standard toolholders? The 32 mm shank is suitable for toolholders accommodating a 32 mm shank diameter and provides stable clamping for milling operations. How many cutting edges does the tool have and what is the benefit? The tool features five cutting edges, which distribute cutting forces over more edges for smoother material removal and improved productivity in continuous production. Who manufactures the cutter and who supplies it in Europe? The cutter is produced by Teknik Makina and supplied in Europe by Metav Werkzeuge; the SKU for reference is S946TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of rigid 32 mm shank support, integrated internal coolant and full compatibility with XEKT 1904 indexable inserts for reliable milling performance; order the S388TM directly via Metav Werkzeuge or consult our specialists for application guidance. S388TM 32 mm Shank Milling Cutter with internal coolant for XEKT 1904 indexable inserts — Teknik Makina The S388TM 32 mm shank milling cutter is a precision tool designed for indexable insert milling with integrated internal coolant and a long 220 mm overall length for extended reach in industrial and workshop operations. 32 mm shank diameter for secure clamping Internal coolant for improved chip evacuation Compatible with XEKT 1904 Korloy inserts Overall length 220 mm, 81 mm cutting length Improved chip control and coolant-fed cutting performance The cutter’s internal coolant channel directs cutting fluid close to the insert tip, improving chip evacuation and reducing heat at the cutting edge. This results in more consistent tool life and fewer thermal deformations during extended runs. For machining centres and clamping systems where coolant delivery is possible, the internal feed ensures stable cutting conditions even with longer overhangs, keeping the machining process efficient and predictable. Rigidity and insert system compatibility for predictable results A 32 mm shank diameter provides high rigidity in the toolholder, which lowers runout and vibration when paired with appropriate collets or shrink-fit holders. The S388TM has been engineered for XEKT 1904 indexable inserts (Korloy), secured with the specified M4 x 8.5 fixing screw and tightened using a T15 Torx key, ensuring repeatable seating and torque transmission. This compatibility simplifies tooling logistics and supports fast insert changes for uninterrupted production. Practical design for workshop and industrial milling tasks With an overall length of 220 mm and a cutting length of 81 mm, the tool balances reach and stiffness for slotting and face-milling tasks where extended overhang is required. The two cutting edges provide an efficient material removal approach with predictable chip formation. The compact weight of approximately 1.192 kg aids handling during tool changes while maintaining mass to dampen chatter. The combination of mechanical stability and coolant supply makes this cutter suitable for a range of machining tasks where insert systems are preferred over solid-carbide solutions. Contact Metav Werkzeuge in Emmerich for a tailored quotation or to confirm insert compatibility for the S388TM shank milling cutter: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: S388TM Designation: Schaftfräser for XEKT 1904 indexable inserts Manufacturer: Teknik Makina Facts Shank diameter: 32 mm Overall length: 220 mm Cutting length: 81 mm Number of cutting edges: 2 Weight: 1.192 kg Torx key: T15 Fixing screw: M4 x 8.5 Special features Internal coolant through the shank Compatible with XEKT 1904 indexable inserts Insert manufacturer match: Korloy FAQ What inserts fit this milling cutter? The S388TM is designed for XEKT 1904 indexable inserts; compatibility with Korloy XEKT 1904 inserts is confirmed. Is the coolant channel internal or external? This shank milling cutter features an internal coolant feed routed through the shank to the insert area for improved cooling and chip removal. Which toolholder types are suitable for a 32 mm shank? A 32 mm shank requires a corresponding collet or shrink-fit holder rated for that diameter to ensure secure clamping and low runout for the S388TM. How many cutting edges does the tool have and what does that mean for feed rates? The tool has two cutting edges; this geometry typically allows higher chip load per tooth and can support efficient feed rates with the correct insert grade and machining parameters. What securing hardware is required for the inserts? Inserts are fastened with an M4 x 8.5 screw tightened with a T15 Torx key, ensuring consistent clamp force for reliable seating. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a 32 mm shank and compatibility with XNKT 0805 indexable inserts for stable, efficient machining and fast insert changes; order the shank milling cutter directly via Metav Werkzeuge or request tailored advice from our consultants. Shank milling cutter S843TM – 32 mm shank · for XNKT 0805 indexable inserts (Teknik Makina) Shank milling cutter S843TM designed for indexable-insert milling in general workshop and industrial setups, offering a compact 125 mm overall length and secure Torx clamp for consistent performance. 32 mm shank diameter Compatible with XNKT 0805 inserts Three cutting edges for stable machining Secured with M4x10 Torx screw (T15) Maximise metal removal with consistent stability The robust 32 mm shank and three cutting edges combine to deliver improved stiffness and repeatable cutting behaviour. This design reduces chatter and keeps the cutting forces predictable, which supports higher process reliability during slotting or peripheral milling operations. The result is more consistent cycle times and less need for corrective rework, creating clear productivity gains on the shop floor. Rapid, secure insert changes to reduce downtime Indexable tooling with XNKT 0805 inserts simplifies maintenance: worn cutting edges are replaced rather than the whole tool, which lowers consumable costs and shortens machine downtime. The insert is clamped by an M4x10 Torx screw, tightened with a T15 key for a secure and repeatable fit; this mechanical simplicity translates into quicker set-ups and reliable clamping forces without complex procedures. Compact dimensions for flexible toolholder integration With an overall length of 125 mm and a compact head profile, the shank cutter is suitable for a wide range of toolholders where a 32 mm mounting diameter is standard. The combination of compact length and a rigid shank helps to maintain axial and radial stability, enabling safer entry into tighter work zones while preserving surface quality and dimensional control. Proven compatibility for predictable procurement Designed to accept XNKT 0805 indexable inserts and optimised for inserts from Korloy, this cutter supports standardisation across insert inventories and simplifies procurement. Where workshop efficiency and consistent supply are priorities, choosing a cutter that fits established insert families helps to harmonise tooling across machines and operators, supporting smoother production planning. Contact Metav Werkzeuge for customised recommendations on tooling layouts and insert selection for Teknik Makina’s S843TM shank milling cutter — our consultants can advise on integration with existing holders and supply options via Metav Werkzeuge. Technical Data SKU: S843TM Manufacturer: Teknik Makina eClass: 21180806 ETIM: EC011860 Article: for XNKT 0805 Indexable Inserts Facts Shank diameter: 32 mm Diameter: 32 mm Overall length: 125 mm Cutting edges: 3 Torx screw: M4x10 Torx key: T15 Special features Compatible with XNKT 0805 indexable inserts Compatible insert manufacturer: Korloy Secure Torx-clamped insert mounting FAQ Which insert type fits this cutter? The shank milling cutter S843TM accepts XNKT 0805 indexable inserts; Korloy inserts in this size are compatible. What is the shank diameter and why does it matter? Shank diameter is 32 mm — a larger shank improves rigidity and helps maintain cutting stability under load. How many cutting edges does the tool have? The tool is equipped with three cutting edges, which balances material removal rate with stable cutting forces. Which screw and key are required for insert clamping? Insert clamping uses an M4x10 Torx screw, tightened with a T15 key for secure, repeatable fixing. Is the S843TM suitable for standard toolholders? The overall length of 125 mm and the 32 mm shank make the S843TM suitable for many common holders designed for a 32 mm mounting diameter Teknik Makina: Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of ADKT 1505 insert compatibility, a compact Ø32 mm cutting diameter and a secure Ø25 mm shank for fast setup and consistent results; order via Metav Werkzeuge or consult the team for application advice. Shank milling cutter S307TM – indexable-insert milling cutter, Ø32 mm, 3 flutes (Teknik Makina) The Shank milling cutter S307TM is designed for medium-duty milling using ADKT 1505 indexable inserts and is ideal for production runs where quick insert changes and dependable clamping are essential Ø 32 mm cutting diameter Three cutting edges for efficient chip removal Compatible with ADKT 1505 indexable inserts Shank Ø 25 mm for secure clamping Consistent cutting performance for repetitive production The S307TM delivers reliable chip formation through its three-flute geometry, which balances cutting force and evacuation to maintain process stability. Thanks to the Ø32 mm diameter and a cutting length of 45 mm, the design supports steady material removal rates while keeping vibrations low. For production environments this means fewer interruptions and a predictable surface finish, helping to maintain cycle times and reduce scrap. Quick insert changes and robust clamping reduce downtime A practical benefit of the indexable-insert concept is the speed of service: inserts can be replaced without removing the cutting head from the machine. The cutter uses a M4x10 Torx screw secured with a T15 key, enabling fast, repeatable insert changes and secure retention. The shank Ø25 mm provides positive clamping in common toolholders, lowering the risk of tool movement and minimising rework caused by poor seating. Compatibility with established insert systems for process flexibility Engineered for use with ADKT 1505 inserts and compatible with ISCAR insert standards, this cutter allows integration into existing tooling inventories and simplifies spare-part management. Selecting a cutter that matches common inserts reduces procurement complexity and supports quicker set‑ups across multiple machines. The combination of indexable inserts and a standardised shank supports cost-effective machining by separating cutting edges from the tool body. Practical workshop advantages and handling information With an overall length of 120 mm and a mass of 0.477 kg, the tool is compact to handle and straightforward to store. The shank construction and balanced flute count help to reduce operator fatigue during tool changes and inspection. Where surface quality and throughput matter, choosing an indexable milling cutter like this one helps shops achieve repeatable results while keeping maintenance tasks simple and economical. Contact Metav Werkzeuge today for tailored recommendations on Teknik Cutting Tools' S307TM shank milling cutter and to discuss suitable insert grades and clamping solutions from our Emmerich team Technical data Article number: S307TM Manufacturer: Teknik Makina Eclass: 21180806 ETIM: EC011860 Facts Diameter: 32 mm Number of flutes: 3 Cutting length: 45 mm Overall length: 120 mm Shank diameter: 25 mm Weight: 0.477 kg Special features For ADKT 1505 indexable inserts Compatible with ISCAR inserts Torx screw M4x10 Torx key size T15 Indexable-insert milling cutter design FAQ Which inserts fit this cutter? The S307TM is designed for ADKT 1505 indexable inserts and is compatible with inserts from ISCAR, allowing use of established grades and geometries. What toolholder size is recommended for safe clamping? A toolholder that accepts a Ø25 mm shank provides secure clamping and stable machining when using this indexable-insert cutter. How many flutes does the cutter have and what is the benefit? The cutter has three flutes, which balance cutting stability and chip evacuation for consistent surface finish during medium-duty milling. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of high stability, precise compatibility with APKT 1604 indexable inserts and an 80 mm cutting length for efficient milling cycles; order the cutter directly via Metav Werkzeuge or consult our specialists for process integration. S453TM – Shaft milling cutter by Teknik Makina, Ø 32 mm shank, 80 mm cutting length S453TM is a shank-type milling cutter designed for robust slotting and shoulder milling operations using APKT 1604 indexable inserts, ideal for medium‑ to heavy‑duty CNC applications Ø 32 mm shank diameter 80 mm cutting length for deep cuts Compatible with APKT 1604 indexable inserts Three cutting edges for smooth chip evacuation Faster cycle times through stable shank design The cutter delivers measurable productivity gains thanks to its Ø 32 mm shank, which increases rigidity at the tool holder and reduces chatter during interrupted cuts. With an 80 mm cutting length, the tool enables deeper engagement in a single pass, reducing the number of operations required to reach final dimensions. The combination of shank stability and generous cutting span supports higher feed rates and contributes directly to shorter cycle times on batch work. Fewer tool changes with standardised insert compatibility Built to accept APKT 1604 indexable inserts, the tool integrates seamlessly into workflows that already use common triangular‑style inserts. Compatibility with Korloy inserts gives access to a broad range of grades for steel, stainless steels and cast materials, so tooling can be adapted to the workpiece without replacing the holder. The insert is secured with a M4x10 Torx screw and a T15 key, ensuring repeatable clamping and quick index changes that keep machine downtime to a minimum. Consistent surface results from optimised geometry The cutter’s 90° cutting angle and three cutting edges were selected to balance stock removal and surface finish. Three flutes promote efficient chip evacuation while maintaining a uniform cutting load across the insert edges; this helps to achieve consistent shoulder faces and reduces the need for secondary finishing. The tool’s overall length of 350 mm and substantial mass provide damping that stabilises the cut, which is particularly beneficial when machining with longer overhangs. Clear specification and workshop support for confident procurement Technical clarity in the specification—shank Ø, cutting length, number of cutting edges and insert type—means purchasing decisions can be made with confidence and without unnecessary enquiries. Metav’s offering positions precision equipment within reach of workshops by combining product availability with application knowledge; for complex set‑ups the distributor can advise on insert grades and machine parameters to match material and productivity targets. This approach minimises sourcing risk while supporting efficient implementation on the shop floor. Contact Metav Werkzeuge for a tailored recommendation on the Teknik Cutting Tools S453TM shank milling cutter — call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss insert grades and CNC parameters Technical Data Article number: S453TM Manufacturer: Teknik Makina SKU: S453TM Facts Shank diameter: 32 mm Cutting length: 80 mm Overall length: 350 mm Number of cutting edges: 3 Weight: 2.274 kg Cutting angle: 90° Special features For APKT 1604 indexable inserts Compatible with Korloy inserts Torx screw M4x10, Torx key T15 Three‑flute geometry for improved chip control FAQ What insert type does this cutter use? The cutter accepts APKT 1604 indexable inserts; compatible insert grades from Korloy are suitable depending on the workpiece material. Is the shank diameter suitable for standard tool holders? Yes — the Ø 32 mm shank is compatible with common 32 mm collet or shrink‑fit holders used in milling spindles. How many cutting edges are fitted and what benefit do they bring? The tool uses three cutting edges, which balance material removal and chip evacuation to deliver smoother cutting and stable surface quality. Can the screw be tightened with a standard key? The insert is secured by an M4x10 Torx screw requiring a T15 Torx key for reliable, repeatable clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 32 mm shank combined with internal coolant and a secure BDMT 1704 insert interface to maintain steady production and reduce set-up time; order directly via Metav Werkzeuge or consult our specialists for application advice. Shank milling cutter S582-1TM — 32 mm shank with internal coolant for BDMT 1704 indexable inserts (Teknik Makina) Shank milling cutter for BDMT 1704 indexable inserts designed for reliable indexable-insert milling tasks where coolant delivery and secure clamping are required *32 mm shank with 60 mm cutting length *Internal coolant for reliable cooling *Compatible with BDMT 1704 inserts (Kyocera) *Three cutting edges, robust 150 mm overall length Increased metal removal with directed coolant flow The tool’s internal coolant channel directs cutting fluid close to the cutting zone, improving chip evacuation and temperature control. That results in more consistent cutting forces and reduced heat-related edge wear, which supports longer tool life and steadier part quality. Intended for indexable-insert milling workflows, this configuration helps maintain production throughput while lowering the frequency of unscheduled tool changes. Fast insert changes and repeatable clamping for uptime A robust mechanical interface ensures quick replacement of BDMT 1704 indexable inserts from Kyocera, secured by the M4x10 Torx screw and set with a T15 Torx key. The clear screw specification and standardised insert type reduce assembly time and improve repeatability between setups, minimising downtime and contributing to predictable cycle times in batch production. Stable shank geometry for consistent machining results With a 32 mm shank and 150 mm overall length, the cutter provides a balanced combination of accessibility and rigidity. The 60 mm cutting length and three cutting edges produce uniform engagement and a stable cut pattern, lowering the risk of chatter in typical milling operations. The measured mass of 0.895 kg contributes to a steady rotational inertia that supports repeatable results on horizontal and vertical milling spindles. Workshop-ready design and application guidance Designed for practical shop-floor use, the cutter suits a range of indexable-milling tasks where fast changeover and reliable coolant delivery matter. For complex setups or to confirm compatibility with a specific machine spindle or insert grade, Metav’s technical advisors can provide application guidance and recommendations to match coolant, insert grade and machining parameters to the intended workpiece and cycle requirements. Discuss machining requirements and availability with Metav Werkzeuge’s specialists in Emmerich: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: S582-1TM Manufacturer: Teknik Makina Product type: Shank milling cutter for BDMT 1704 indexable inserts Facts Diameter: 32 mm Overall length: 150 mm Cutting length (shaft): 60 mm Shank diameter: 32 mm Number of cutting edges: 3 Weight: 0.895 kg Torx key: T15 Torx screw: M4x10 Internal coolant: yes Special features Compatible with BDMT 1704 indexable inserts Suitable for Kyocera inserts Quick insert change via M4x10 Torx screw Designed for reliable chip evacuation via internal coolant FAQ Which insert type fits this cutter? The cutter accepts BDMT 1704 indexable inserts; the design and clamping system are matched to that insert family for consistent seating and performance. Is internal coolant supplied through the tool body? Yes, the tool features internal coolant routing to the cutting zone to assist chip removal and temperature control during milling. What torque and screw type secure the insert? Inserts are secured with an M4x10 Torx screw, tightened using a T15 Torx key as specified for the S582-1TM. Can this cutter be used with non-Kyocera inserts? The cutter is specified for BDMT 1704 inserts and is listed as compatible with Kyocera grades; alternative manufacturers producing BDMT 1704-compatible inserts may be used if seat geometry and clamping match exactly. What are the key dimensions to check for machine compatibility? Important dimensions include the 32 mm shank diameter, 150 mm overall length and 60 mm cutting length; these determine spindle fit and reach for the intended operation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid Ø 32 mm shank and 4 cutting edges for consistent material removal; compatibility with LNHU 0904 indexable inserts keeps changeovers quick. Order via Metav Werkzeuge or consult the Metav team for application advice and availability. Shank milling cutter S329TM – Ø 32 mm, 4‑cut, for LNHU 0904 indexable inserts by Teknik Makina A robust Shank milling cutter S329TM engineered for reliable peripheral milling and efficient insert changeovers in CNC and milling operations. Ø 32 mm shank diameter 4‑cut geometry for efficient removal For LNHU 0904 indexable inserts (Walter) Torx screw M3x7, Torx key T8 Maximised rigidity for stable, productive cutting A larger shank diameter delivers measurable benefits in everyday production: the Ø 32 mm body increases stiffness and reduces deflection compared with smaller holders, so the tool maintains a consistent cutting line under load. With 4 cutting edges and a cutting length of 40 mm, the design supports productive feeds and predictable tool life. The result is improved process stability and fewer scrapped parts during heavy cuts, which directly contributes to shorter cycle times and higher first‑pass yield. Fast insert changes and lower operating costs The cutter accepts LNHU 0904 indexable inserts and is specified for inserts from Walter, enabling quick edge rotation or replacement without the need for regrinding. Fixing is achieved with a M3x7 Torx screw, tightened with a T8 key, ensuring reproducible clamping force and straightforward maintenance. Indexable inserts provide an economical cost‑per‑edge approach: worn edges are replaced rapidly, downtime is reduced and toolroom workload is minimised — a clear operational advantage when planning batch runs or mixed production. Practical dimensions that suit workshop workflows With an overall length of 150 mm and a net weight of 0.972 kg, the cutter balances handling convenience with structural mass that helps dampen vibration. The 40 mm effective cutting length is suitable for a range of peripheral milling tasks where controlled chip evacuation and stable engagement matter. Operators and maintenance teams benefit from the straightforward geometry and documented specifications, which support predictable tooling cycles and make inventory planning easier for purchasing and production control. For technical application advice or to reserve the Teknik Makina S329TM for planned production runs, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 — Metav's specialists will assist with compatibility checks and delivery options Technical data Article number (SKU): S329TM Manufacturer (raw data): Teknik Makina Designation: Shank milling cutter for LNHU 0904 indexable inserts ECLASS: 21180806 ETIM: EC011860 Data Shaft diameter: 32 mm Cutting length (shaft): 40 mm Overall length: 150 mm Number of cutting edges: 4 Weight: 0.972 kg Special features For LNHU 0904 indexable inserts Compatible insert manufacturer: Walter Torx screw: M3x7 Torx key size: T8 FAQ Which inserts fit this cutter? The cutter is designed for LNHU 0904 indexable inserts; the tool accepts inserts from Walter and compatible suppliers for the LNHU 0904 profile. What is the shank diameter and why does it matter? The shank diameter is 32 mm; a larger shank increases stiffness and reduces deflection, improving stability during heavier milling operations with the S329TM shank milling cutter. How many cutting edges does the tool have? This milling tool features 4 cutting edges, which support higher material removal rates and balanced cutting forces during peripheral milling. What fastening hardware is required for the inserts? Insert clamping uses an M3x7 Torx screw and requires a T8 Torx key for secure and repeatable tightening on the S329TM. Is the S329TM suitable for automated tool changers? The tool’s dimensions (Ø 32 mm shank, 150 mm overall length) and standard insert fixation make it compatible with many automatic tool‑change systems; suitability should be confirmed against the specific machine interface and holder. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust indexable design and rigid 32 mm shank for stable machining and consistent chip control; the compatibility with LNMT 0804 inserts and ISCAR standards simplifies tool selection and replacement. Order directly via Metav Werkzeuge or consult our specialists for application matching and setup advice. Shank milling cutter S300-1TM — indexable tool with 32 mm shank and five cutters by Teknik Makina Shank milling cutter S300-1TM for light to medium-duty milling operations using LNMT 0804 indexable inserts; designed for secure clamping and fast insert changes Compatible with LNMT 0804 indexable inserts 32 mm shank diameter for rigid mounting Five cutting edges for balanced chip load Torx M2.5x7 screws, T8 key for quick service Higher throughput from indexable insert technology The use of LNMT 0804 indexable inserts allows rapid insert replacement and predictable cutting performance, which translates directly into improved machine uptime and lower per-part costs. The cutter's five cutting edges distribute the cutting forces evenly, reducing vibration and enabling a steadier feed rate. For production environments where cycle time matters, this configuration supports sustained material removal without frequent full-tool exchanges, making process planning more efficient. Secure clamping and straightforward maintenance A 32 mm shank offers enhanced rigidity in the toolholder, reducing runout and improving surface finish on the workpiece. Insert retention is managed with M2.5x7 Torx screws, serviced using a T8 key, which simplifies maintenance procedures on the shop floor and shortens changeover time. The combination of a robust holder body and standardised fastenings supports repeatable seating of the insert, contributing to consistent dimensional results across batches. Integration into existing machining cells and tooling systems Designed as a shank-mounted milling solution, the cutter's 120 mm overall length and 40 mm cutting length provide a practical balance between reach and stiffness for many spindle configurations. Compatibility with ISCAR-type reference standards for LNMT 0804 inserts eases procurement and tooling management, allowing maintenance teams to standardise on commonly available inserts. The tool's mass and geometry are optimised for stability, helping to maintain tool life and predictability under continuous use. Contact Metav Werkzeuge for tailored tooling advice and to confirm insert compatibility — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: S300-1TM Name: Shank milling cutter (Schaftfräser) for LNMT 0804 indexable inserts Brand: Teknik Makina Numbers / Core technical data Shank diameter: 32 mm Cutting length (shaft): 40 mm Overall length: 120 mm Diameter: 32 mm Number of cutters: 5 Weight: 0.775 kg Torx screw: M2,5x7 Torx key: T8 Designs / Special features Compatible with LNMT 0804 indexable inserts Suitable insert manufacturer reference: ISCAR Shank-mounted design for rigid clamping Files available: 62de7e53148ec6b71020ff8d, 62de7ee7bd24461b3d5f7a74 FAQ What insert type does the cutter accept? The cutter accepts LNMT 0804 indexable inserts; the design follows common industry dimensions for straightforward replacement. Which insert manufacturers are compatible with this tool? The tool is matched to ISCAR-style LNMT 0804 inserts; Teknik Makina’s S300-1TM is optimised for those insert geometries. What fastening hardware is required for insert changes? Insert retention uses M2.5x7 Torx screws tightened with a T8 key, facilitating quick and secure insert replacement. Is the shank size suitable for standard collets and holders? With a 32 mm shank, the cutter is intended for holders and adaptors designed for that diameter, offering a balance of reach and rigidity. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine the 32 mm shank rigidity with a 60 mm cutting length and secure M4x10 Torx clamping for consistent indexable-insert performance; order the tool directly via Metav Werkzeuge or consult our technical advisors for selection support. Shank milling cutter S720TM – 32 mm shank, for VCGT 1604 indexable inserts (Teknik Makina) The Shank milling cutter S720TM is a precision indexable-insert holder designed for robust milling tasks, offering stable clamping and straightforward insert replacement for general CNC and workshop applications. 32 mm shank diameter 60 mm cutting length Compatible with VCGT 1604 inserts Secure M4x10 Torx clamping, T15 key Increased rigidity for predictable machining results The combination of a 32 mm shank and a 200 mm overall length is engineered to balance accessibility with stiffness; this reduces deflection and vibration during material removal. With two cutting edges arranged for stable engagement, the toolholder is intended to maintain consistent chip control and surface finish under moderate to heavy cuts. The clamping system, secured by an M4x10 Torx screw and tightened using a T15 key, is specified to hold the insert firmly in place, which results in repeatable positioning and reduced downtime for clamp checks. These characteristics make the holder suitable where reproducible results and tool reliability are required. Optimised geometry for efficient insert usage A 60 mm cutting length provides extended cutting engagement while preserving rigidity at the tool tip. The insert pocket is configured for VCGT 1604 indexable inserts, enabling quick index changes and standardised insert stocking across multiple cutters. The shank-mounted design is compatible with conventional toolholders and spindle interfaces used in milling operations, and the tool's mass (approx. 1.225 kg) contributes to a steady cutting behaviour without excessive tool overhang. By using standard insert formats, machine shops can streamline inventory and achieve predictable cycle times, improving throughput in batch and single-piece production environments. Practical workshop benefits and supplier confidence The modular approach of an indexable-insert holder simplifies maintenance: worn inserts are replaced rather than the whole tool, lowering lifecycle costs and minimising service intervals. The component is delivered ready for installation with the correct Torx fastener specification, and the proven shank diameter supports common collet and chuck systems. For procurement and supply reliability, Metav acts as a central European quality filter and distributor, ensuring consistent availability and trained advisory services. If additional clarification on fitment or machine compatibility is required, technical guidance is available to support the selection process. For tailored advice or to secure supply of the S720TM shank milling cutter, contact Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 for fast delivery from Emmerich and expert product guidance Technical data SKU: S720TM Manufacturer: Teknik Makina eClass: 21180806 ETIM: EC011860 Designation (EN): for VCGT 1604 Indexable Inserts Core dimensions Shank diameter: 32 mm Cutting length (shank): 60 mm Cutting edges: 2 Overall length: 200 mm Weight: 1.225 kg Features Compatible inserts: VCGT 1604 Torx clamping screw: M4x10 Torx key size: T15 Files: 62de7ee50f56dbb4de4dbf58, 62de7e4fbd24461b3d5f7a29 FAQ Which insert type fits this cutter? The cutter is designed for VCGT 1604 indexable inserts; the pocket and clamping geometry are matched for that format to ensure correct seating and chip formation. What torque tool is required for the clamping screw? A T15 Torx key is specified for the M4x10 clamping screw; this ensures secure fastening and correct seating of the insert in the pocket. Is the shank suitable for standard collets and chucks? The 32 mm shank diameter fits common milling toolholding systems; it is intended for use where a robust shank is required to reduce overhang and increase rigidity. How many cutting edges are available and what is the benefit? The holder accepts inserts producing two cutting edges in the cutting cycle, which balances material removal rate with stable cutting forces for improved surface finish. What are the basic dimensions to check for machine compatibility? Check the 32 mm shank diameter, 200 mm overall length, and 60 mm cutting length against machine clearance and tool changer requirements before procurement. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a stable clamping situation with a 25 mm shank, a robust Ø32 mm cutter diameter and four cutting edges that deliver consistent chip removal for industrial milling tasks; order directly via Metav Werkzeuge or consult the technical team if additional data is required. Shaft Indexable Milling Cutter S647TM — Ø32 mm, 4 cutting edges | Teknik Makina The Shaft Indexable Milling Cutter S647TM is engineered for insert milling with XOMX 0602–1204 indexable inserts, providing reliable material removal in CNC and industrial milling applications. Compatible with SECO XOMX 1204 inserts Ø32 mm cutter diameter Four cutting edges for steady cutting Shank Ø25 mm for secure clamping High material removal rate with consistent chip control The milling head combines a 32 mm diameter with four cutting edges, designed to maintain a steady material removal rate while reducing vibration and chatter. The geometry and 90° cutting angle deliver predictable cutting forces, which is particularly valuable in serial production and when machining shoulders or face surfaces. The indexable insert system simplifies edge changes and lowers downtime compared with solid-tool grinding, so production runs benefit from shorter interruptions and consistent surface quality. Robust shank and secure fastening for industrial spindles A 25 mm shank diameter and a precise overall length of 120 mm guarantee stable clamping in milling holders and tool holders used on industrial CNC machines. The tool is supplied with a Torx fastening concept (M3.5×8.5 screw, Torx key T10) to ensure repeatable insert seating and minimised play. This mechanical reliability reduces the risk of insert displacement under higher feed rates, supporting both higher productivity and reduced scrap rates in demanding workshops. Application flexibility and maintenance efficiency Compatible with XOMX 1204 indexable inserts and specified for use with SECO-style inserts, the tool is suited for a variety of materials and machining tasks where indexable milling is preferred. The replaceable insert system simplifies maintenance and inventory management: worn cutting edges are swapped quickly without regrinding the whole tool, which lowers operating costs and preserves spindle time. With a tool weight of 0.965 kg, balance and handling during tool changes remain manageable for workshop staff and automated tool changers alike. For reliable machining performance from Teknik Makina components, contact Metav Werkzeuge for ordering and detailed technical advice: info@metav-werkzeuge.com or call +49 2822 7131930 — Metav Werkzeuge will assist with selection and delivery from Emmerich. Technical Data SKU: S647TM Product type: Shaft indexable milling cutter Compatibility: XOMX 0602–1204 indexable inserts Core dimensions Cutter diameter: 32 mm Shank diameter: 25 mm Cutting length: 45 mm Overall length: 120 mm Number of cutting edges: 4 Weight: 0.965 kg Cutting angle: 90° Materials & features Insert type: XOMX 1204 compatible Recommended insert manufacturer: SECO Fastening: Torx screw M3.5×8.5 Torx key size: T10 Typical use: Indexable insert milling for industrial CNC FAQ What insert type does this cutter use? The shaft indexable milling cutter accepts XOMX 1204 indexable inserts; it is designed for use with SECO-compatible inserts for reliable seating and performance. Can the cutter be securely clamped in standard tool holders? Yes, the tool features a 25 mm shank and an overall length of 120 mm, providing secure clamping in compatible milling holders for repeatable results. How many cutting edges are available and what benefit do they provide? The cutter has four cutting edges, which deliver smoother chip flow and more even wear distribution compared with fewer-flute alternatives, improving surface finish and tool life. Is special fastening hardware required for inserts? Standard Torx fastening is used: screw M3.5×8.5 and Torx key T10, ensuring repeatable insert clamping and straightforward maintenance. Is this tool suitable for automated tool changers? With a compact weight of 0.965 kg and standard shank size, the cutter is compatible with many automated tool changer systems commonly used in industrial CNC environments. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of precise insert compatibility, a compact 32 mm cutting diameter and a robust 25 mm shank for consistent, low‑vibration milling results; order the tool directly via Metav Werkzeuge or consult the technical advisors for application guidance. S763TM shank cutter – 32 mm diameter, for ANHX 1004–1206 indexable inserts (Teknik Makina) S763TM is a purpose-built shank-mounted milling cutter intended for indexable‑insert milling, offering secure insert clamping and straightforward maintenance for workshop and production use 32 mm cutting diameter 25 mm shank diameter 40 mm cutting length Compatible with ANHX 1004 inserts Built for stable, repeatable cutting in production The S763TM is engineered to deliver consistent machining through its 3 cutting edges and a 90° cutting angle, which together provide an even load distribution and predictable engagement. These geometric choices reduce chatter and support repeatable tolerances across batches, making the cutter suitable for serial production as well as precise one‑off work. The assembly is optimised for indexable‑insert workflows, allowing the milling head to maintain cutting stability during extended runs. Fast insert changes and reduced downtime Designed with practical shop routines in mind, the tool uses a M3x7 Torx screw and accepts a T8 key for secure insert fixation. The 25 mm shank and a 125 mm overall length create a compact, rigid setup for milling heads, while the 40 mm cutting length balances reach and stiffness. Quick insert replacement reduces machine downtime, and the clear mechanical interface with ANHX 1004 indexable inserts simplifies tool maintenance and inventory management for production planners and maintenance staff. Suited to workshops and industrial environments This cutter was developed for users seeking reliable insert milling with established indexable systems; it is compatible with inserts from Palbit and addresses the needs of both trade workshops and industrial shops that demand reproducible results. The tool’s moderate weight of 0.783 kg and straightforward geometry facilitate handling during tool changes and set‑up, while the robust shank supports stable cutting forces in routine machining tasks. For buyers looking for a dependable insert milling solution, the S763TM represents a pragmatic balance of performance and serviceability. Order the Teknik Makina S763TM shank cutter through Metav Werkzeuge for guaranteed supply from Emmerich and expert application advice—contact info@metav-werkzeuge.com or call +49 2822 7131930 for detailed support Technical data Article number: S763TM Manufacturer: Teknik Makina Suitable for inserts: ANHX 1004–1206 (Palbit) Facts Diameter: 32 mm Shank diameter: 25 mm Cutting length: 40 mm Number of cutting edges: 3 Overall length: 125 mm Weight: 0.783 kg Cutting angle: 90° Torx screw: M3x7 Torx key: T8 Special features Designed for ANHX 1004 indexable inserts Compatible with Palbit inserts 3‑flute design Secure Torx clamping Compact, rigid shank FAQ What types of inserts fit this cutter? The S763TM accepts ANHX 1004–1206 indexable inserts and is listed as compatible with Palbit insert variants. How is the insert secured in the milling head? Insert clamping is accomplished with a M3x7 Torx screw; the recommended tightening tool is a T8 key for correct seating and repeatable clamping force. What are the key dimensions for setup and tool holders? Key dimensions include a 32 mm cutting diameter, 25 mm shank diameter and 125 mm overall length, which assist in selecting appropriate tool holders and setting stick‑out. Is the cutter suitable for serial production runs? Yes, the combination of 3 cutting edges and a 90° cutting angle provides stable cutting behaviour that suits repetitive production tasks and helps preserve surface quality across batches. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust geometry, straightforward insert compatibility and secure clamping for dependable milling results; order the shank milling cutter directly via Metav Werkzeuge or ask our consultants if needed. Shank Milling Cutter S034TM – 32 mm Ø, 4 flutes (for APKT 1003–1604 Indexable Inserts) — Teknik Makina The Shank Milling Cutter S034TM is a tool body designed to accept APKT 1003–1604 indexable inserts for versatile face and slot milling in industrial production environments. Ø32 mm cutting diameter 4 cutting edges for stable machining 25 mm shank diameter, 35 mm cutting length Compatible with APKT 1003 indexable inserts Reliable cutting geometry for steady material removal The S034TM milling body delivers consistent performance through its standardised geometry: a Ø32 mm cutting diameter combined with 4 flutes and a 90° cutting angle ensures predictable chip formation and even radial engagement. This results in improved surface quality and reduced vibration during passes. The design supports repeatable tool setting and facilitates reliable process control on series production parts. By using indexable inserts, the assembly limits downtime to a rapid insert change, sustaining production throughput. Secure clamping and easy maintenance for production continuity Designed with a 25 mm shank and a 35 mm effective cutting length, the cutter body offers a balanced connection between spindle and tool, enhancing rigidity for medium-duty operations. Fastening is secured with an M2.5x5.5 Torx screw, operated with a T8 key, enabling quick insert replacement without special tooling. The compact mass of 0.768 kg supports controlled dynamics in the tool holder and simplifies handling during changeovers. Routine maintenance focuses on torque checks and insert inspection, which keeps machine downtime to a minimum and supports predictable scheduling. Practical compatibility and straightforward shop-floor integration The tool is specified for use with APKT 1003 indexable inserts and aligns with inserts from YG-1, making it a flexible option where these insert systems are already standardised. Its universal insert interface and common fixation method reduce the need for unique spare items in the tool crib, lowering logistical complexity. The combination of indexable technology and the cutter body’s features supports an efficient cost-per-cut strategy: worn cutting edges are replaced rather than the entire tool, delivering economical operation over many cycles. Contact Metav Werkzeuge to discuss how the Teknik Makina S034TM can be integrated into existing tooling setups and to arrange delivery from our Emmerich stock Technical Data SKU: S034TM Manufacturer: Teknik Makina Product: Shank milling cutter for APKT 1003-1604 indexable inserts Compatible inserts: APKT 1003 Compatible insert manufacturer: YG-1 Facts Cutting diameter: 32 mm Shank diameter: 25 mm Cutting length: 35 mm Overall length: 100 mm Number of cutting edges: 4 Cutting angle: 90° Weight: 0.768 kg Special features Torx screw: M2.5x5.5 Torx key: T8 Indexable-insert system: APKT 1003–1604 compatibility Balanced design for reduced vibration Rapid insert-change capability FAQ What inserts fit this milling body? The Shank Milling Cutter S034TM is specified for APKT 1003 indexable inserts and supports the APKT 1003–1604 range; compatible inserts from YG-1 are suitable for this cutter body. How is the insert secured to the cutter? Insert retention uses an M2.5x5.5 Torx screw tightened with a T8 key, which enables quick and repeatable insert changes for the Teknik Makina S034TM cutter body. Which shank size is required for the tool holder? The tool features a 25 mm shank diameter; holders and adaptors sized for a 25 mm shank are appropriate when using the S034TM milling body. What cutting diameter and flute count does the tool offer? This cutter provides a Ø32 mm cutting diameter with 4 flutes, offering a balance between material removal rate and surface finish for standard milling tasks. Is this cutter suitable for high-speed machining? The S034TM is designed as a robust insert-carrying cutter body; cutting speed suitability depends on the chosen APKT inserts and machining parameters rather than on the body alone—select inserts and settings matched to the application. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid cutter body with a Ø32 mm shank and a 45 mm effective cutting length for stable, reproducible milling results; order the tool directly via Metav Werkzeuge or consult the Metav team for application advice. Indexable milling cutter S038TM — for APKT 1003–1604 indexable inserts, Ø32 mm, 4 cutting edges (Teknik Makina) The Indexable milling cutter S038TM is a shank-mounted cutter body designed for finish and semi-finish face and shoulder milling with APKT 1003–1604 indexable inserts, offering a compact 150 mm overall length for standard workshop tool posts Ø 32 mm shank diameter 45 mm effective cutting length Holds APKT 1003 inserts (YG‑1 compatible) Torx M2.5x7 fastening, T8 key required Greater rigidity for consistent machining results A larger shank diameter is the simplest way to increase tool stability in milling operations: the Ø32 mm shank of this milling cutter reduces deflection under load and improves surface finish consistency when compared with smaller holders. The 150 mm overall length keeps the tool projection moderate, which further reduces vibration and enables higher feed rates with predictable tool life. For production environments where process repeatability matters, the combination of shank size and compact geometry translates into fewer reworks and more predictable cycle times. Secure insert clamping and simple serviceability The cutter body is supplied to accept APKT 1003 indexable inserts and is compatible with YG‑1 insert geometries, simplifying procurement and inventory. Insert retention uses a Torx M2.5x7 screw tightened with a T8 key, ensuring repeatable clamping torque and straightforward insert changes at the machine. Indexable inserts let workshops separate cutting-edge wear from the expensive cutter body: worn edges are replaced in seconds, keeping downtime to a minimum and cost per cutting edge low. The 90° cutting angle offers reliable shoulder clearance and predictable chip flow for general-purpose milling. Optimised geometry for efficient machining Equipped with 4 cutting edges, the cutter body balances material removal with smooth engagement, spreading cutting forces across multiple edges for reduced load per insert. The 45 mm cutting length provides ample axial engagement for many face and shoulder operations without overextending the insert life. These characteristics support efficient material removal while maintaining control over heat and chip evacuation—advantages that improve throughput and lower the total cost of machining per component. Practical workshop details and integration With a mass of approximately 0.946 kg, the tool body is easy to handle during tool changes and inspection routines. The design suits general workshop tool posts and common milling spindle configurations; the compact overall length aids storage and tool magazine organisation. For traceability and ordering within a controlled procurement process, use SKU S038TM when requesting the cutter body or spare fastening screws from Metav Werkzeuge. As a reliable partner, Metav supports selection and logistics so that precision tools arrive quickly and without administrative friction. For tailored advice on application, compatibility or to secure the Teknik Makina S038TM from Metav Werkzeuge, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to request a quotation or technical guidance Technical Data Article number: S038TM Manufacturer: Teknik Makina SKU: S038TM Compatible inserts: APKT 1003 Compatible insert maker: YG-1 Fastening screw: M2,5x7 (Torx T8) Numbers / Core technical data Shank diameter: 32 mm Effective cutting length: 45 mm Overall length: 150 mm Weight: 0.946 kg Number of cutting edges: 4 Cutting angle: 90° Special features / Versions For APKT 1003–1604 indexable inserts Torx screw clamping system M2,5x7 Compatible with YG‑1 insert geometries Compact 150 mm overall length FAQ Which insert grade and size fits this cutter? The cutter accepts APKT 1003 indexable inserts; matching grades from YG‑1 are compatible and commonly used with this cutter body. What toolholder shank does the body require? The body presents a Ø32 mm shank interface; compatibility with a specific spindle or adaptor depends on the machine’s toolholder system. How is the insert secured and what key is needed? Inserts are fastened with an M2.5x7 Torx screw; a T8 key is required to achieve the correct clamping. Is the cutter suitable for shoulder milling with light overhangs? Yes. The 90° cutting angle, 45 mm cutting length and Ø32 mm shank offer good rigidity for face and shoulder milling with moderate overhang. What identifier should be quoted when ordering spare parts or replacements? Use SKU S038TM and reference the Teknik Makina cutter body when ordering replacement screws, inserts or spare bodies. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of precise insert compatibility, a rigid Ø32 mm shank and a compact overall length for controlled, high-productivity milling. Order the cutter through Metav Werkzeuge or contact the Metav consultants for tailored technical advice. Indexable Insert Milling Cutter S662-1TM – Ø32 mm shank, for APKT 1705 inserts (Teknik Makina) A versatile Indexable Insert Milling Cutter S662-1TM engineered for insert-based milling operations where quick indexable-changeover and stable toolholding are required in conventional and CNC setups. Ø32 mm shank for stable mounting Compatible with APKT 1705 inserts Three cutting edges for steady feed M4x10 Torx screw included (T15) Stable mounting for consistent machining results The Ø32 mm shank and compact body deliver increased rigidity and reduced vibration during cuts, which directly supports repeatable dimensional control. A rigid tool body reduces chatter, so the cutter body maintains a predictable cutting behaviour when fitted into standard toolholders. The solid mounting diameter is especially valuable for operations that demand consistent surface quality and tight tolerances, as it minimises run-out and preserves the lifetime of inserts and adapter components. Fast insert changes and predictable clamping This milling cutter accepts APKT 1705 indexable inserts and is supplied with an M4x10 Torx screw and T15 key specification for secure, repeatable clamping. The use of a standard screw and key simplifies maintenance cycles and reduces downtime, because inserts can be exchanged without specialist tools. Compatibility with common insert geometries enables straightforward inventory management and faster set-up times on the shop floor, promoting efficient shift-to-shift throughput. Geometry designed for stable material removal Equipped with three cutting edges, the cutter body balances material removal rate and feed stability to deliver smooth chip evacuation and consistent cutting forces. The 60 mm effective cutting length offers a compromise between reach and stiffness, allowing for both side and face-milling applications where a controlled depth of cut is required. This geometry supports steady machining under moderate cutting parameters, helping to protect insert edges and extend service intervals. Practical build for everyday workshop reliability With an overall length of 200 mm and a mass of 1.236 kg, the tool body is compact enough for constrained setups yet heavy enough to feel robust during handling. The body has been designed for repeatable fitment in standard arbors and holders; as a result, tool change procedures are straightforward and safe. The combination of accessible clamping hardware and a standard insert system reduces the need for specialised spare parts, making maintenance predictable and cost-effective. Integration into production and supply benefits Suppliers such as Taegutec are listed as compatible insert manufacturers, which supports flexible purchasing and fast supply-chain decisions. The cutter body is produced by Teknik Makina and is intended for industrial use in milling applications that rely on indexable insert systems. For workshops seeking simplified tooling logistics, the standardisation around APKT 1705 inserts helps consolidate cutter bodies and inserts across multiple machines, lowering administrative complexity and stock variety. For application-specific recommendations or to arrange a supply, contact Metav Werkzeuge — the experts at Metav will advise on the Teknik Makina indexable milling cutter S662-1TM and compatible inserts, and can support fast procurement and delivery from Emmerich. Technical Data Article number: S662-1TM Manufacturer: Teknik Makina Facts Shank diameter: 32 mm Cutting length (shaft): 60 mm Overall length: 200 mm Number of cutting edges: 3 Weight: 1.236 kg Special features Compatible inserts: APKT 1705 Compatible insert manufacturers: Taegutec Fastening screw: M4x10 Torx Torx key size: T15 FAQ Which inserts fit this cutter body? The cutter is designed for APKT 1705 indexable inserts; compatible inserts from manufacturers such as Taegutec can be used with the S662-1TM. What is the shank diameter and why it matters? The tool features a 32 mm shank, which provides improved rigidity and reduced run-out compared with smaller diameters, supporting consistent machining accuracy. How many cutting edges does the cutter use? The cutter body accepts arrangements for three cutting edges, offering a balance between material removal rate and feed stability. Which fastening hardware is provided or required? Clamping uses an M4x10 Torx screw with T15 key specification for secure and repeatable insert retention. Who manufactures this cutter and where can it be sourced? The tool body is manufactured by Teknik Makina and can be sourced via Metav Werkzeuge; reference SKU S662-1TM when enquiring. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a 32 mm diameter, five cutting edges and a 130 mm overall length for stable, high‑feed milling; order the indexable insert milling cutter directly via Metav Werkzeuge or consult our specialists for application advice. Indexable Insert Milling Cutter S050TM — for APMT 0903 Indexable Inserts, 32 mm diameter The Indexable Insert Milling Cutter S050TM is a shank-mounted cutter designed for heavy‑duty face and shoulder milling with APMT 0903 indexable inserts, offering reliable compatibility and robust chip evacuation. 32 mm diameter for robust material removal Five cutting edges for high productivity Compatible with APMT 0903 Korloy inserts Torx clamp M2.5x5.5 with T8 key Stable cutting geometry for consistent material removal The cutter features a 32 mm nominal diameter and five cutting edges, which together ensure balanced load distribution and improved surface finish during interrupted cuts. The combination of a substantial shank and a 130 mm overall length reduces vibration and runout, enabling stable milling in both roughing and semi‑finishing operations. The tool body geometry has been conceived to promote reliable chip flow; this reduces recutting and helps maintain tool life, resulting in measurable process stability on mixed production batches. Engineered compatibility and quick insert changes Designed specifically for APMT 0903 indexable inserts, the holder accepts inserts from Korloy, enabling straightforward integration into existing tooling stocks. The clamping system uses a Torx M2.5x5.5 screw with a T8 key, allowing quick, repeatable insert replacement and minimal downtime at the machine. For workshops that value modularity, this cutter delivers the operational benefit of fast insert changes and predictable seating accuracy, which shortens setup time and supports consistent part quality across shifts. Practical workshop benefits and handling With a mass of 0.73 kg and a compact form factor, the tool balances rigidity with manageable handling during mounting and inspection. The solid shank design simplifies clamping in standard toolholders while the 30 mm effective cutting height provides ample depth-of-cut options for common face‑milling tasks. Where tool life and repeatability matter, this cutter offers a practical route to increased throughput without complex retooling—suitable for jobbing shops and production lines alike. Integrating into production and quality routines The milling cutter supports predictable process parameters when paired with the recommended inserts; predictable cutting geometry facilitates programming of CAM paths and easier optimisation of feeds and speeds. For quality assurance, the tool’s dimensions and clamping features enable consistent repositioning after maintenance. When traceability and supply reliability are priorities, partnering with a supplier that acts as a quality filter for the European market reduces procurement risk and streamlines stock management. For reliable compatibility with APMT 0903 inserts and assured delivery from a trusted partner, contact Metav Werkzeuge to secure the Teknik Cutting Tools Indexable Insert Milling Cutter S050TM — expert advice and rapid supply from Emmerich available on request. Technical data Article number: S050TM Manufacturer: Teknik Cutting Tools / Teknik Makina Facts Diameter: 32 mm Shank diameter: 32 mm Overall length: 130 mm Cutting height: 30 mm Number of cutting edges: 5 Weight: 0.73 kg Special features Compatible with APMT 0903 indexable inserts Suitable for Korloy inserts Torx clamp screw M2.5x5.5 Torx key size T8 FAQ What inserts fit this cutter? The cutter is designed for APMT 0903 indexable inserts and is compatible with inserts from Korloy, which ensures straightforward integration into existing insert stocks. How many cutting edges does the tool have and what is the benefit? The tool has five cutting edges, which provide improved productivity and a more even load distribution for smoother milling and extended insert life. What are the key dimensions to check when ordering toolholders? Check the 32 mm shank diameter and the 130 mm overall length to ensure compatibility with the existing toolholder and sufficient stick‑out for the intended milling operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com