Gibt es einen Hahn und Kolb Online Shop?

Robust and precise machining for repeatable T‑groove production: the combination of a 32 mm cutting diameter, secure 25 mm shank and compatibility with standard CCMT 09T3 inserts delivers steady material removal and reduced downtime. Benefit from fast insert changes and reliable clamping for continuous workshop operation — order or request application advice via Metav Werkzeuge. T-slot cutter TKC103TM — indexable milling cutter, Ø 32 mm (Teknik Makina) A T-slot cutter TKC103TM engineered for accurate T‑groove and T‑nut milling on CNC and conventional milling heads; compatible with CCMT 09T3 indexable inserts for efficient production use. Ø 32 mm cutting diameter Shank Ø 25 mm for firm clamping Compatible with CCMT 09T3 inserts Four cutting edges for steady removal Precision T‑grooves with consistent results This indexable milling tool delivers repeatable T‑slot geometry by combining a clear cutting diameter with a balanced cutter body. The 32 mm diameter and the design for CCMT 09T3 inserts ensure that each pass removes material evenly, which reduces the need for rework and shortens cycle times. The cutter’s four cutting edges distribute cutting forces across multiple flutes, lowering vibration and improving surface finish. For production environments, this translates into predictable throughput and less tool handling between operations. Fast maintenance and secure clamping for uninterrupted workflow A stable connection between tool and spindle is essential for precise milling; the cutter’s 25 mm shank provides a solid clamping interface for common toolholders, improving rigidity during plunge and side cuts. Insert retention is handled with an M3.5x9 Torx screw, and a T15 key secures the carbide plates quickly and safely. The practical arrangement of screw and key speeds up insert changes and minimises machine downtime, allowing rapid restoration of cutting capacity after resharpening or replacement of inserts. The tool’s moderate mass (0.434 kg) helps to balance rigidity with manageable tool handling in the workshop. Built for production and workshop flexibility With an overall length of 100 mm and a compact cutting-shank arrangement, the cutter offers reach without excess overhang, making it suitable for typical T‑slot and T‑nut operations on milling machines and machining centres. Compatibility with widely available CCMT plates keeps tooling costs predictable and supports a range of grades for different workpiece materials. The design suits both batch production and jobbing environments where quick changeovers and consistent results matter. Applied correctly, the tool contributes to streamlined processes and reliable part quality across repeated runs. For supply, technical matching and reliable delivery of Teknik Makina cutting tools, contact Metav Werkzeuge in Emmerich by eMail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for tailored advice and order handling Technical data Article number: TKC103TM Brand: Teknik Makina Product name: T-slot cutter Core specifications Diameter: 32 mm Shank diameter: 25 mm Cutting-shank diameter: 16 mm Cutting height: 14 mm Number of cutting edges: 4 Shank length (cutting): 33 mm Overall length: 100 mm Weight: 0.434 kg Features and compatibility Compatible with CCMT 09T3 inserts Insert screw: M3.5x9 Torx Torx key size: T15 Indexable milling cutter for T‑grooves Four-flute cutting geometry FAQ What inserts does this cutter use? The cutter is designed for CCMT 09T3 indexable inserts; those inserts are widely available in several grades to match different workpiece materials. How is the insert secured? Insert retention uses an M3.5x9 Torx screw; a T15 key is required to tighten or loosen the screw for replacement. Which shank diameter is required for the toolholder? The cutter has a 25 mm shank diameter and should be mounted in a compatible collet or holder that provides sufficient clamping length for rigidity. What applications suit this milling cutter? This tool is intended for producing T‑slots and T‑nuts in general machining applications where indexable insert solutions are preferred for cost efficiency and quick servicing. Is the cutter suitable for automated production environments? Yes, the cutter’s stable geometry, four cutting edges and standard insert compatibility make it suitable for CNC production runs that require repeatability and efficient tool changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine stable 25 mm shank, 3 mm cutting width and compatibility with 3C ZT.D indexable inserts to ensure consistent grooving performance; order the holder directly via Metav Werkzeuge or ask our consultants for fitment advice. K681TM Grooving Clamp Holder — 25 mm shank, 3 mm cutting width (Teknik Makina) The K681TM grooving clamp holder is a lathe-mounted toolholder engineered for secure clamping of 3C ZT.D indexable inserts, providing precise grooving and parting operations in turning applications Robust 25 mm shank for stable mounting Accepts 3C ZT.D indexable inserts 35 mm cutting height for consistent engagement 200 mm overall length for extended reach Engineered stability for repeatable grooves The holder is built with an emphasis on rigidity and repeatability: the 25 mm shank and a body diameter of 33 mm combine to reduce deflection during cut entry, while the measured weight (1.576 kg) helps damp vibration. Together these attributes maintain a stable tool position, which translates into consistent groove geometry and longer insert life. For workshops aiming to reduce scrap and rework, this mechanical stability is a clear operational advantage. Precise clamping designed for indexable inserts Compatibility with 3C ZT.D indexable inserts and a 3 mm cutting width makes the clamp ideal for fine grooving tasks and narrow parting lines. The holder accepts ISO shank configuration S25R and the related designation 3C‑R ZT.D, enabling quick insert changes and repeatable seating accuracy. Indexable inserts offer predictable cutting edges and straightforward indexing; when combined with a reliable clamping system, tool changeover times are reduced and process reproducibility improves. Practical design for workshop efficiency At 200 mm overall length the toolholder offers reach for deeper set-ups while maintaining manageable overhang. The 35 mm cutting height ensures correct edge alignment on most standard turning centres, reducing the need for shims or complex set-up procedures. This straightforward compatibility and robust mechanical design support faster set-ups and steady production runs, helping to keep cycle times predictable and tooling costs under control. For tailored advice on integrating the K681TM into existing tool chains, contact Metav Werkzeuge for consultation and ordering assistance. Technical data Article number: K681TM Manufacturer: Teknik Makina Designation: Stechklemmhalter Facts Shaft diameter: 25 mm Cutting height: 35 mm Cutting width: 3 mm Overall length: 200 mm Body diameter: 33 mm Weight: 1.576 kg Special features Compatible inserts: 3C ZT.D Suitable insert supplier: ZCC Shank designation: S25R Alternate holder designation: 3C-R ZT.D FAQ What insert type fits this holder? The K681TM is designed for 3C ZT.D indexable inserts and is specified to work with inserts from ZCC. Which machine spindles or turrets suit the holder? The holder's 25 mm shank and ISO designation S25R make it compatible with toolposts and turret stations that accept 25 mm round shanks. How does the holder support repeatable set-ups? A combination of the rigid 25 mm shank, controlled body diameter and accurate clamping geometry ensures repeatable seating and consistent groove dimensions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of stable clamping, precise cutting diameter and quick insert replacement for uninterrupted production. Benefit from compatibility with CCMT 09T304 inserts, a 20 mm shank for secure mounting and straightforward assembly via Torx hardware — order through Metav Werkzeuge or request specialist advice for application checks. Back countersink C106TM by Teknik Makina — compatible with CCMT 09T304, 20 mm shank The Back countersink C106TM is a rear-side countersinking tool intended for precision metalworking with indexable inserts, delivering repeatable results in set-up-optimised production environments Back countersink C106TM by Teknik Makina Compatible with CCMT 09T304 indexable inserts 20 mm shank for stable tooling Max cutting diameter 33 mm, overall length 152 mm Stable insert mounting for consistent results The tool features a robust mounting concept that accepts CCMT 09T304 indexable inserts, enabling fast insert changes and predictable component finish. A 20 mm shank ensures dependable clamping in common toolholders, reducing chatter and improving dimensional consistency across batches. The single cutting-edge geometry focuses cutting forces into a defined zone, which supports repeatability and lowers adjustment frequency — a clear economic advantage for serial production. Precision countersinking that supports process reliability With a max cutting diameter of 33 mm and an overall length of 152 mm, the device is configured to reach recessed positions while maintaining cutting stability. The single cutter arrangement offers controlled material removal and a predictable chamfer profile, simplifying subsequent assembly steps where a clean seat for screw heads is required. The construction prioritises machining control and process safety to help maintain consistent component quality across cycles. Quick assembly and maintenance to keep uptime high Fast, secure fastening is provided by the supplied Torx hardware (screw M3.5x8.5) and the designated Torx T15 key engagement, which simplifies re‑tensioning after insert replacement. The modest mass of 0.308 kg and compact geometry assist in straightforward handling during tool changes and inspection. For users seeking integration advice or confirmation of holder compatibility, technical guidance can be provided to ensure a smooth implementation and minimal set-up time on the shop floor. Contact Metav Werkzeuge for tailored integration advice or to reserve the C106TM; direct technical enquiries are welcome via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: C106TM Manufacturer: Teknik Makina Designation: Back countersink Facts Cutting diameter (max): 33 mm Body diameter: 21 mm Shank diameter: 20 mm Overall length: 152 mm Cutting edges: 1 Weight: 0.308 kg Torx screw: M3.5 x 8.5 Torx key: T15 Special features For indexable inserts: CCMT 09T304 Fastening: Torx screw M3.5x8.5 (T15) FAQ Which insert type fits this countersink? The C106TM accepts CCMT 09T304 indexable inserts, offering quick replacement and standardised geometry for consistent chamfering. What shank diameter is required for the holder? The tool has a 20 mm shank; ensure the toolholder or collet accommodates a 20 mm shank for secure clamping. What is the maximum cutting diameter and reach? Maximum cutting diameter is 33 mm and the overall length is 152 mm, suitable for accessing recessed rear surfaces. Which fastening hardware is used for the insert? Assembly uses a Torx screw M3.5x8.5; a T15 driver is specified for correct torque and secure clamping. How many cutting edges does the tool have and what is the effect? The device carries 1 cutting edge, which concentrates cutting forces for a predictable chamfer and easier process control. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, indexable milling solution that combines stable clamping with rapid insert changes; the combination of a Ø33 mm cutting diameter and a 32 mm shank delivers consistent chip control and process reliability. Order the tool directly via Metav Werkzeuge or consult the team for integration advice. Indexable milling cutter S487TM by Teknik Makina — for 3PKT 1004 indexable inserts, Ø33 mm, 3 cuts The Indexable milling cutter S487TM is a robust tool body engineered for industrial milling applications with 3PKT 1004 indexable inserts, designed to provide stable machining over long runs Compatible with Taegutec 3PKT 1004 inserts Ø33 mm cutting diameter 32 mm shank diameter for stable clamping 200 mm overall length, 40 mm cutting length Efficient compatibility that reduces setup time and tooling complexity The tool body is built for proven insert systems, offering straightforward compatibility with 3PKT 1004 indexable inserts and Taegutec geometries. This standardised approach shortens changeover and reduces tooling variants in stock, which directly improves machine uptime. With a Ø33 mm cutting diameter the cutter balances rigidity and chip evacuation, enabling predictable cutting forces and repeatable results in series production. Such compatibility is a rational advantage for production planners seeking predictable throughput. Design features that enhance stability and insert security A substantial 32 mm shank ensures secure clamping in standard tool holders and reduces run-out risk during heavy milling passes. The body uses a Torx M2.5x7 fastening arrangement, requiring a T15 driver for insert fixation — a simple, reliable method that secures inserts firmly while allowing fast replacement. The combination of shank dimension and robust fixing offers a clear benefit: fewer vibrations, improved surface finish and extended tool life for the inserts, which translates into lower process costs over time. Practical dimensions for workshop logistics and handling At an overall length of 200 mm and with a 40 mm cutting length, the cutter fits common mill setups without compromising reach or rigidity. The balanced geometry and modest mass (approx. 0.495 kg) make handling and tool changes uncomplicated on the shop floor. The body is optimised for indexable inserts, so maintenance consists mainly of routine insert changes and screw checks — straightforward tasks that keep downtime to a minimum and support consistent production performance. Reliable supply and integration support from Metav Beyond the technical benefits, the tool is backed by a dependable supply channel that suits workshop procurement. Choosing a standardised indexable cutter body reduces the number of special orders and supports a lean stocking strategy. For planners and purchasers, the combination of standard insert compatibility and solid mechanical design delivers a pragmatic route to stable machining results and predictable inventory management. Discuss integration of the Teknik Cutting Tools S487TM and secure dependable supply via Metav Werkzeuge GmbH — contact Metav Werkzeuge for ordering and technical coordination at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: S487TM Manufacturer: Teknik Makina Designation: Indexable milling cutter for 3PKT 1004 Indexable Inserts Brand: Teknik Makina Facts Cutting diameter: 33 mm Shank diameter: 32 mm Number of cutting edges: 3 Overall length: 200 mm Cutting length: 40 mm Weight: 0.495 kg Torx screw: M2.5x7 Torx key size: T15 Special features Compatible with Taegutec inserts For 3PKT 1004 indexable inserts Indexable insert system tool body Robust shank for stable clamping FAQ What inserts fit this cutter? The cutter accepts 3PKT 1004 indexable inserts; compatibility with Taegutec insert geometries is specified for straightforward replacement and performance. Which driver is required for insert fixation? Insert screws use a Torx M2.5x7 fastener; a T15 driver is the correct size for secure tightening. What are the key dimensions to check for holder compatibility? Important dimensions are the 32 mm shank diameter and the 200 mm overall length; these determine holder fit and overhang behaviour. How many cutting edges does the tool provide? The body is configured for 3 cutting edges, permitting balanced chip formation and steady cutting forces in milling operations. Is the tool suitable for long production runs? The combination of a solid shank, standardised insert system and simple insert fixing makes the body suitable for continuous production when managed with correct insert selection. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of internal coolant, a compact 33 mm diameter, and secure Torx fastening for consistent chip control and extended insert life; order the insert milling cutter directly via Metav Werkzeuge or consult Metav's specialists for application advice Insert milling cutter S492TM – Insert milling cutter for BLMP 0904, 33 mm diameter, internal coolant (Teknik Makina) Insert milling cutter S492TM designed for indexable-insert milling in industrial and workshop environments, compatible with BLMP 0904 inserts and optimised for secure fastening and coolant-fed machining Internal coolant for reliable chip evacuation Compatible with BLMP 0904 Taegutec inserts 33 mm cutter diameter, 32 mm shank 150 mm overall length with 4 cutting edges Consistent material removal with coolant-fed tip design The insert milling cutter delivers controlled chip evacuation thanks to its integrated internal coolant channel, which directs coolant to the cutting zone and reduces thermal load. This results in more stable cutting conditions and a longer effective life for the replaceable indexable inserts. The tool body’s 33 mm diameter and the specified 40 mm cutting length ensure a predictable metal removal rate and repeatable surface quality for medium-duty pocketing and face-milling tasks, while the robust construction contributes to reduced downtime through fewer unplanned tool changes. Secure clamping and straightforward insert retention Designed for secure mechanical connection, the cutter uses Torx T10 drive and M3.5x8.5 fastening screws for each insert pocket, providing repeatable seat torque and minimised vibration at speed. The 32 mm shank gives a stable interface with the toolholder, improving concentricity and balance. Together these features support consistent geometric tolerances in serial production and make the system suitable for standard milling holders used in CNC machining centres. Broad compatibility with BLMP 0904 indexable inserts The body is configured for BLMP 0904 indexable inserts and is compatible with Taegutec-manufactured inserts, enabling flexible selection of grades and geometries to match workpiece materials and cutting conditions. The insert system allows fast index changes and straightforward inventory management: keeping a small set of insert grades available lets one adapt the same cutter body for roughing or finishing without replacing the entire tool body. Workshop efficiency and maintenance considerations With four cutting positions, the insert milling body offers efficient use of replacement inserts and economical machining cycles. The design supports routine maintenance procedures such as torque checks for the M3.5x8.5 screws and inspection of seat faces for wear. Because the cutter is an indexable system rather than a solid tool, workshops benefit from reduced toolcost per cutting edge and faster turnaround when changing wear parts, improving overall throughput in production runs Contact Metav Werkzeuge for tailored cutting parameters and procurement support referencing SKU S492TM — Metav’s technical consultants will advise on insert grades and holder selection Technical data SKU: S492TM Product type: Insert milling cutter Compatible inserts: BLMP 0904 Manufacturer: Teknik Makina Core specifications Cutter diameter: 33 mm Overall length: 150 mm Shank diameter: 32 mm Cutting length: 40 mm Number of cutting edges: 4 Weight: 1.108 kg Torx key: T10 Fastening screw: M3.5x8.5 Features & compatibility Internal coolant Suitable for Taegutec BLMP 0904 inserts Indexable-insert system Label: 33mm shank milling cutter BLMP 0904 L150mm with internal coolant FAQ What inserts fit the S492TM body? The S492TM insert milling cutter is configured for BLMP 0904 indexable inserts and is compatible with Taegutec grades designed for that insert geometry. Is the cutter coolant-fed and how does that help? Yes, the cutter features internal coolant delivery; targeted coolant reduces heat at the cutting edge, improves chip control and can extend insert life. What fastening hardware is required for the inserts? The cutter uses M3.5x8.5 screws with a Torx T10 drive for secure insert retention and repeatable clamping torque. Can the S492TM be used with common CNC toolholders? The 32 mm shank provides a stable connection for standard toolholders that accept that shank diameter; confirm holder compatibility for the intended spindle and clamping system. How many cutting edges are available before index changes? The cutter body offers 4 insert positions; each position can be indexed or replaced independently, allowing economical reuse of the insert body Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of compatibility, rigidity and straightforward serviceability: the cutter’s 33 mm diameter and compatibility with LNMU 0303 indexable inserts reduce changeover time while the 32 mm shank and 200 mm overall length ensure stable machining. Order the tool directly via Metav Werkzeuge or consult the specialists for machining recommendations. Indexable shank cutter S689TM – 33 mm diameter, for LNMU 0303 indexable inserts (Teknik Makina) A durable Indexable Shank Cutter S689TM designed for high-productivity milling with LNMU 0303 inserts, suitable for a wide range of general machining tasks 33 mm cutter diameter Compatible with LNMU 0303 inserts 32 mm shank diameter 200 mm overall length Boosted throughput with indexable insert technology The tool is built around the LNMU 0303 indexable insert system, which enables rapid insert changes and consistent cutting geometry. Fitting standard Tungaloy inserts lowers tooling costs by allowing multiple reuses of the cutter body while the insert performance ensures repeatable chip control. With 5 cutting edges on the head, machining cycles can be optimised for productive face and shoulder milling, so cycle times are reduced and tool inventory is simplified. Indexable systems also limit downtime compared with solid-carbide replacements, improving shop-floor efficiency. Stiffness and stability for consistent part quality A substantial 32 mm shank provides the axial and radial rigidity necessary for tighter tolerances when machining medium-duty components, while the 33 mm body diameter contributes to a stable cutting platform. The 60 mm cutting length (head cutting length) balances reach and rigidity, making the tool suitable where both access and dimensional control matter. The tool weight of 1.112 kg is consistent with a robust design and supports vibration dampening during interrupted cuts, which helps maintain surface finish and dimensional accuracy across production batches. Simple service and secure clamping for workshop use Maintenance and reconditioning are straightforward: inserts are secured with M2.5x7 Torx screws and a T8 Torx key is used for fastening, ensuring quick, reliable replacement with common workshop tools. The modular design reduces consumable costs and simplifies stockkeeping; workshop teams can replace worn inserts quickly and return the cutter to service without specialised equipment. Supplied as a finished tool body compatible with industry-standard indexable inserts, this cutter integrates easily into existing toolholders and tool management systems, reducing procurement complexity. Contact Metav Werkzeuge for tailored application guidance and to request the Teknik Makina S689TM indexable shank cutter; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: S689TM Product type: Shank cutter Brand: Teknik Makina Compatible inserts: LNMU 0303 Compatible insert manufacturer: Tungaloy Core specifications Cutter diameter: 33 mm Shank diameter: 32 mm Overall length: 200 mm Cutting length: 60 mm Number of cutting edges: 5 Weight: 1.112 kg Torx key: T8 Torx screw: M2.5x7 Materials & features Indexable insert system Replaceable cutting inserts Torx screw clamping Label: 33mm Shank cutter LNMU 0303 L200mm FAQ Which inserts are required for this tool? The cutter uses LNMU 0303 indexable inserts; compatible inserts from Tungaloy are recommended for optimal fit and performance. What is the usable cutting length of the tool? The tool provides a 60 mm cutting length on the head, allowing for a balance of reach and rigidity in typical milling operations. What shank size is needed in the toolholder? A toolholder capable of accepting a 32 mm shank is required; the robust shank ensures stable clamping and reduced deflection. How are the inserts fastened and which key is needed? Inserts are secured with M2.5x7 Torx screws and require a T8 Torx key for replacement and torque-controlled servicing. Is the cutter supplied as a ready-to-fit body or with inserts included? The S689TM is supplied as a finished cutter body compatible with LNMU 0303 inserts; inserts are stocked separately and should be selected according to application needs. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the holder's combination of sturdy clamping, precise geometry and quick insert changes to keep parting and grooving cycles consistent and efficient; order the parting clamp holder via Metav Werkzeuge or consult our experts for application advice. Parting clamp holder — 25 mm shank, for 3C indexable inserts (Teknik Cutting Tools) The Parting clamp holder is a dedicated grooving and parting tool holder designed for CNC lathe applications, offering robust clamping for narrow-width cuts and reliable compatibility with standard 3C indexable inserts. 25 mm shank diameter for stable clamping Compatible with 3C indexable inserts 3 mm cutting width for narrow parting cuts 200 mm overall length, balanced weight 0.782 kg Stable clamping and consistent cut quality The holder is engineered to provide stable clamping and reduced vibration thanks to its solid 25 mm shank and rigid body geometry. This results in improved surface finish and repeatable parting depths, which is especially valuable for series production. The tool’s cutting height of 50 mm and compact footprint ensure that the insert sits securely at the correct centreline, so the machining process is controlled and deviations are minimised. The design is intended to integrate with standard lathe tool posts and to maintain cutting stability during medium-duty parting operations. Fast insert changes and lower operating costs Compatibility with 3C indexable inserts enables fast, tool-free or minimal-tool insert indexing and replacement, reducing downtime and increasing machine uptime. Because inserts are indexable, the effective tool life is extended: a single insert offers multiple cutting edges before replacement is required. The 3 mm cutting width supports narrow groove and parting operations, helping to conserve material and lower scrap rates while delivering predictable chip control when paired with suitable inserts and machine parameters. Compact dimensions for straightforward setup With an overall length of 200 mm and a nominal diameter of 33 mm, the holder is compact yet accessible for adjustment and inspection. The S25R shank designation aligns with common shank standards, simplifying selection for turret-mounted or post-mounted setups. At a mass of 0.782 kg, the holder is lightweight enough for rapid handling while heavy enough to contribute to system stability, allowing fast clamping without compromising rigidity. Clear dimensional data supports planning for fixture layout and turret clearance. Practical application and workshop reliability This clamp-style tool holder is suitable for repeatable grooving and parting tasks where accurate edge location and quick servicing are required. Its simple clamping mechanism and standardised interface make it a pragmatic choice for machine shops seeking efficient changeover routines and predictable process behaviour. Where workflow efficiency and uptime are priorities, the holder contributes to leaner set-up times and steadier production throughput. For procurement or technical queries about the Teknik Cutting Tools parting clamp holder K648TM, contact Metav Werkzeuge for availability, machining recommendations and compatibility checks Technical data Article number: K648TM Item name: Parting clamp holder Manufacturer: Teknik Makina Core data Shank diameter: 25 mm Cutting width: 3 mm Cutting height: 50 mm Total length: 200 mm Weight: 0.782 kg Diameter: 33 mm Special features Compatible with 3C indexable inserts Shank type: S25R Holder designation: 3C-R S224 For grooving and parting operations FAQ What insert type does this holder accept? The holder accepts 3C indexable inserts; it is configured for standard 3C insert geometry to enable quick indexing and replacement for the parting clamp holder K648TM. Which shank specification is used for mounting? Mounting is based on the S25R shank specification, matching common 25 mm turret or post tool holders for secure installation of the parting clamp holder. What is the maximum cutting width supported? The holder is specified for a 3 mm cutting width, which is suitable for narrow parting and grooving operations where minimal material removal is required. Is the holder suitable for high-speed parting? The holder is designed for stable clamping and repeatable use; compatibility with high-speed cutting depends on insert selection and machine capability when using the parting clamp holder K648TM. How does the holder aid changeover times? By using 3C indexable inserts and a straightforward clamping arrangement, the holder reduces insert-change and set-up time, improving operational efficiency in series machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Specifications: Order Number: U633TM Item: Indexable Drill usable with WCM- 06T3 Indexable Inserts of Korloy Brand: Teknik Makina Numbers and Data: Diameter: 33mm Weight: 1.102kg Total length: 225mm Diameter Connection: 32mm Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Benefit from the combination of stable clamping, a 33 mm cutting diameter and compatibility with 4NKT 0603 indexable inserts for consistent material removal; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Schaftfräser — shank-mounted milling cutter, 33 mm diameter, for 4NKT 0603 indexable inserts — Teknik Makina A Schaftfräser designed as a shank-mounted milling cutter for 4NKT 0603 indexable inserts, intended for secure indexable-insert milling on CNC machines and rigid toolholders 33 mm cutting diameter for high material removal 32 mm shank for rigid toolholder clamping Four cutting edges for efficient chip removal Compatible with Taegutec 4NKT 0603 inserts Enhanced stability for consistent machining results The shank-mounted design delivers stable clamping and reduced run-out, helping to maintain consistent cut quality over long tool engagements. With a 32 mm shank and a 220 mm overall length, the tool balances reach and rigidity to minimise vibration and support repeatable geometry in batch production. This combination is particularly beneficial where hold tolerances affect downstream assembly or finishing operations, as the improved stability directly reduces rework and scrap rates. Efficient cutting thanks to four-edged insert geometry Equipped for four cutting edges and a 33 mm diameter, the cutter achieves effective chip evacuation and steady material removal. The generous 35 mm cutting length allows for both peripheral milling and light face cuts, enabling a straightforward transition between roughing and semi-finishing passes. Using indexable inserts means predictable wear behaviour; inserts can be rotated or replaced without removing the holder, which reduces downtime and keeps spindle utilisation high. Practical fastening and service features that save time The insert is secured with an M3x6.5 Torx screw and requires a T8 key for servicing, allowing quick, reproducible clamp torque during insert changes. Compatibility with established insert formats — notably the 4NKT06 / 4NKT 0603 series — makes stocking spares and replacements simpler. The cutter’s solid construction and the option to source inserts from Taegutec support routine maintenance strategies and consistent cutting performance across shifts. Seamless integration into production workflows The cutter is supplied as a ready-to-fit shank-mounted solution that suits CNC milling centres and heavy-duty toolholders where a robust connection is essential. Weighing approximately 1.462 kg, the unit offers the mass needed for stable cutting without compromising tool-change speed on automated systems. The design supports predictable machining windows and can be combined with standard coolant and fixture setups to maintain cycle-time targets and consistent surface finish. Contact Metav Werkzeuge for tailored technical advice or to discuss application suitability of the Teknik Cutting Tools S477-1TM shank-mounted milling cutter; reach our specialists at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: S477-1TM Manufacturer: Teknik Makina Product name: Shank-mounted milling cutter for 4NKT 0603 indexable inserts Key measurements Cutting diameter: 33 mm Shank diameter: 32 mm Cutting length: 35 mm Number of cutting edges: 4 Overall length: 220 mm Weight: 1.462 kg Compatibility & fastening Compatible inserts: 4NKT06 / 4NKT 0603 Suitable insert manufacturer: Taegutec Fixing screw: M3x6.5 Torx Torx key size: T8 FAQ Which indexable inserts fit this cutter? The cutter accepts 4NKT 0603 type inserts (often referenced as 4NKT06); insert changes follow standard indexable-insert procedures for this format. What are the main dimensions of the S477-1TM? Key dimensions for the S477-1TM include a 33 mm cutting diameter, a 32 mm shank and a 220 mm overall length; cutting length is 35 mm. How are the inserts secured? Inserts are fastened with an M3x6.5 Torx screw; a T8 Torx key is used for tightening and removal to ensure repeatable clamping. Is the cutter compatible with Taegutec inserts? Yes, the S477-1TM is compatible with inserts from Taegutec specified in the 4NKT 0603 series. What machining roles is this cutter intended for? The cutter is intended for indexable-insert milling operations on CNC machines where a rigid shank and reproducible insert changes improve productivity and part consistency. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust shank stability, precise insert compatibility and a service-friendly clamping system for dependable cycle times and consistent surface finish. Order the S477TM directly via Metav Werkzeuge or consult the technical team for application-specific advice. Schaftfräser S477TM – indexable insert cutter by Teknik Makina, 33 mm cutting diameter The Schaftfräser S477TM is a precision shank cutter designed for milling operations with indexable inserts, optimised for medium to heavy material engagement and versatile across workshop and light production environments. 33 mm cutting diameter for robust performance 32 mm solid shank for stable clamping Compatible with 4NKT 0603 indexable inserts 35 mm cutting length, four cutting edges Consistent machining through proven insert compatibility Designed around the 4NKT 0603 system, this cutter accepts standard indexable inserts from recognised manufacturers such as Taegutec, which reduces setup complexity and keeps tooling inventories compact. The use of indexable inserts means worn cutting edges are replaced rather than the whole tool, delivering a lower cost per cutting edge and shorter downtime compared with brazed or solid tools. The combination of a defined insert pocket and secure fixing provides predictable cutting geometry, which supports consistent cycle times and a repeatable surface finish. Stable clamping and concentricity for accurate results A 32 mm solid shank ensures firm seating in the spindle or holder, improving concentricity and reducing runout during rotation. Reduced radial runout directly benefits tool life and surface quality, especially when engaging higher material removal rates. The tool’s 33 mm diameter and four cutting edges are balanced to deliver even cutting forces, so the cutter remains stable through plunge and peripheral milling passes. This stability translates into fewer rejects and less rework in serial production. Quick insert changes and secure fixing for continuous operation Maintenance is simplified by the straightforward clamping concept using an M3x6.5 Torx screw and T8 key, enabling fast, repeatable insert replacement without specialised equipment. The 35 mm cutting length offers sufficient engagement for step-down strategies while keeping insert protrusion minimal, which helps maintain rigidity. The robust construction and accessible fixing also reduce the risk of improper seating, limiting unplanned stoppages and enhancing overall equipment effectiveness. Suited for workshops and light industrial production With an overall length of 200 mm and a compact profile, this cutter is a practical choice where space and tool change speed matter. The combination of a solid shank and standardised insert interface supports a range of operations from contouring to face milling. For operations prioritising uptime and repeatability, the S477TM delivers a pragmatic balance between performance and maintainability, making it a logical addition to setups that already use 4NKT-series inserts. Contact Metav Werkzeuge in Emmerich for tailored application guidance and to discuss how the S477TM fits into current machining processes; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: S477TM Manufacturer: Teknik Makina Designation: Shank cutter for 4NKT 0603 indexable inserts Core data Cutting diameter: 33 mm Shank diameter: 32 mm Cutting length: 35 mm Overall length: 200 mm Number of cutting edges: 4 Weight: 1.327 kg Special features Compatible inserts: 4NKT 0603 Suitable insert manufacturer: Taegutec Torx screw: M3x6.5 Torx key size: T8 SKU: S477TM FAQ Which insert type fits this cutter? The cutter accepts 4NKT 0603 indexable inserts; inserts from Taegutec in this format are compatible with the S477TM. How is the insert secured in the cutter? Insert fixation is accomplished with an M3x6.5 Torx screw requiring a T8 key, providing a secure and repeatable clamping interface for the S477TM. What clamping diameter is required for stable operation? A 32 mm solid shank gives high clamping stability; the S477TM is intended for holders or spindles that accommodate a 32 mm shank for optimal concentricity. Is the cutter suitable for heavy material removal? The combination of a 33 mm cutting diameter and four cutting edges makes this cutter appropriate for medium to heavy engagement, depending on the machine power and cutting parameters used with the S477TM. What benefit do indexable inserts provide compared with solid tools? Indexable inserts reduce tool replacement time and cost per cutting edge; the S477TM’s design leverages these advantages for improved uptime and predictable tool costs. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Deliver consistent performance by combining a 33 mm cutting diameter, internal coolant and compatibility with WNMX 09T3 indexable inserts for reliable, economical milling. Benefit from a robust shank design and a 70 mm cutting length that supports steady material removal; order directly via Metav Werkzeuge or request application advice from our consultants. Shank milling cutter for WNMX 09T3 indexable inserts — 33 mm, internal coolant (Teknik Makina) A shank-mounted milling cutter designed for insert-based milling where coolant-through capability and precise shank stability are required 33 mm cutting diameter Internal coolant supply Compatible with Korloy WNMX 09T3 Shank Ø 32 mm for rigid clamping Three cutting edges for stable cutting Faster, more predictable material removal for continuous production The tool is engineered to provide steady material removal with its 33 mm diameter and a cutting length of 70 mm. The shank design with a 32 mm diameter reduces runout when clamped in standard toolholders, which in turn supports repeatable tolerances and consistent surface finishes. Where cycle time and process reliability are critical, the cutter’s three cutting edges balance cutting force and chip load, enabling efficient removal rates without resorting to aggressive feeds that would shorten tool life. These characteristics make the cutter a pragmatic choice for workshops seeking measurable productivity gains. Coolant-through design that protects edges and improves tool life Equipped with internal coolant, the cutter delivers coolant directly to the cutting zone, improving chip evacuation and thermal control. This targeted supply reduces edge temperatures and helps maintain cutting geometry for longer periods; the result is fewer insert changes and more uptime. For operations sensitive to heat or where chip control affects surface quality, the coolant-through feature is a functional advantage that both prevents built-up edge and supports consistent part quality. The mechanism is compatible with standard pressurised coolant systems and is integrated to avoid compromising the shank’s rigidity. Straightforward compatibility and service for workshop workflows Compatibility with WNMX 09T3 indexable inserts — fitted to accepted industry standards — simplifies tooling logistics and reduces the need for specialised inventories. The cutter accepts Korloy-manufactured inserts and is secured with a Torx screw (M3x7) tightened with a T8 key, which keeps changeover quick and reproducible. Routine maintenance is kept simple: replace worn inserts and check the Torx screw torque; the robust shank profile is designed to remain stable through many insert changes. The product is supplied as a ready-to-mount unit, identified as S806-1TM, and is intended for operations where indexable-insert systems are already part of the production setup. For application-specific advice or to purchase this Teknik Makina shank milling cutter via Metav Werkzeuge, contact our technical team for tailored recommendations and delivery options. Technical data Article number: S806-1TM Product type: Shank milling cutter Manufacturer: Teknik Makina Compatible inserts: WNMX 09T3 Suitable insert manufacturer: Korloy Facts Cutting diameter: 33 mm Overall length: 150 mm Shank diameter: 32 mm Cutting length: 70 mm Weight: 0.854 kg Number of cutting edges: 3 Torx key: T8 Torx screw: M3x7 Special features Internal coolant supply Indexable-insert system (WNMX 09T3) Shank-mounted design for rigid clamping Three cutting edges for balanced cutting FAQ Which insert type fits this cutter? The Teknik Makina shank milling cutter accepts WNMX 09T3 indexable inserts; Korloy-manufactured inserts are explicitly listed as compatible and are commonly used with this tool. Is coolant-through capability included? Yes — the cutter is equipped with internal coolant, which delivers coolant directly to the cutting zone to aid chip evacuation and reduce cutting temperatures. What are the critical dimensions for holder selection? Refer to the shank diameter (32 mm) and overall length (150 mm); these dimensions determine compatible toolholders and clamping systems for stable operation. How are inserts secured and changed? Inserts are fixed with a Torx screw (M3x7); the appropriate Torx key is T8. The system is designed for quick, repeatable insert changes while maintaining secure clamping. What is the article number for ordering and reference? Order or reference the cutter using SKU S806-1TM (Teknik Makina shank milling cutter for WNMX 09T3). Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the robust combination of stable clamping, precise cutting geometry and proven insert compatibility for reliable holemaking in production environments; order the part directly via Metav Werkzeuge or consult our specialists for integration advice. Indexable Insert Drill Body U933TM — Ø33 mm, compatible with SPMG 0904 inserts (Teknik Cutting Tools) The Indexable Insert Drill Body U933TM offers a rigid drill-body solution for industrial machining, designed for indexable inserts and heavy-duty chipping conditions while maintaining repeatable hole quality. Ø33 mm cutting diameter 32 mm shank for secure clamping Compatible with SPMG 0904 inserts Cutting length 66 mm Stable holemaking through a rigid shank and optimised geometry The drill body combines a 32 mm shank with a total length of 159 mm and a cutting length of 66 mm, delivering the rigidity required for consistent bore concentricity and reduced vibration. This stability translates into better surface finish and longer insert life when machining batch or continuous production workpieces. The solid construction and balanced geometry also reduce runout at the holder, which is critical when tight positional tolerance is required. Proven insert compatibility and simple toolset integration Designed for indexable inserts of type SPMG 0904, the tool body accepts commonly available insert grades and styles from established manufacturers such as Taegutec and YG-1, simplifying procurement and repopulating tool cabinets. The compatibility with standard insert families allows a swift changeover between grades for differing materials, keeping machine downtime to a minimum and enabling process flexibility across aluminium, steel and alloyed steels where an insert solution is preferred. Practical benefits for production planning and maintenance With a listed mass of 0.815 kg the component is heavy enough to signal robust build quality yet compact for straightforward handling during setup. The defined holder length of 58 mm facilitates secure mounting in standard toolholders and the measured dimensions support predictable tool offsets in CAM programmes. This predictability reduces setup iterations and contributes to efficient cycle planning, especially valuable for small-batch makers and larger workshops alike. For reliable integration into machining centres and stocked tool assortments, contact Metav Werkzeuge to specify the Teknik Cutting Tools Indexable Insert Drill Body U933TM and align insert grades and holder interfaces with existing setups — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: U933TM Manufacturer: Teknik Makina Designation: Indexable insert drill body (Vollbohrer) Diameter: 33 mm Shank diameter: 32 mm Cutting length: 66 mm Holder length: 58 mm Total length: 159 mm Weight: 0.815 kg Insert type: SPMG 0904 Compatible insert makers: Taegutec, YG-1 Intended use: indexable-insert drilling Material: (not specified) FAQ What materials is the U933TM suitable for? The Indexable Insert Drill Body U933TM is specified for use with a range of common workpiece materials when paired with the appropriate insert grade; compatibility with insert makers such as Taegutec and YG-1 enables selection for steel, alloyed steels and aluminium applications. Which insert size is required for this drill body? The drill body accepts SPMG 0904 inserts; matching the correct insert grade for the application will determine cutting performance and tool life for the Indexable Insert Drill Body U933TM from Teknik Cutting Tools. How does the shank diameter support machining stability? A 32 mm shank offers a secure clamping interface and contributes to reduced runout and vibration, improving hole accuracy and insert life during production cycles. Is the tool suitable for use in automated tool changers? The defined holder length (58 mm) and standardised shank diameter facilitate mounting in common holders and automated tool systems when the holder matches the specified dimensions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the robust combination of 33 mm cutting diameter, a 32 mm shank for secure clamping and replaceable inserts to keep machining costs predictable; order directly through Metav Werkzeuge or contact the technical team for compatibility advice. Indexable Insert Drill U793TM — 33 mm diameter, 32 mm shank (Teknik Makina) The Indexable Insert Drill U793TM is an indexable insert drilling solution designed for CNC holemaking where quick insert changes and repeatable bore quality are required 33 mm cutting diameter for medium boremaking 32 mm shank for secure toolholder clamping Compatible with Korloy WCM‑06T3 inserts 165 mm cutting length and 258 mm total length Higher productivity through predictable performance The U793TM is engineered to deliver consistent hole quality and predictable tool life by combining a stable tool body with a standardised insert system. The 33 mm cutting diameter and 165 mm cutting length are configured to support machining cycles where repeatability is essential. Using an indexable concept allows machining parameters to be optimised for productivity: worn edges are corrected by a simple insert change rather than a full tool replacement, which reduces unplanned downtime and lowers per‑hole costs. The measured weight of 1.182 kg and balanced geometry contribute to reduced vibration, supporting better surface finish and tighter tolerances in serial production. Practical handling that shortens setup and service intervals With a 32 mm shank and a 58 mm shank length, the design fits common holders and clamping systems, enabling quick tool changes at the spindle and consistent runout control. The compatibility with Korloy WCM‑06T3 inserts simplifies inventory management when Korloy inserts are already in use, and replaceable inserts mean maintenance is straightforward: minimal tools required for insert replacement and re‑setting. This reduces the time a machine is offline and keeps process capability high — a rational advantage for job shops and production lines that must balance throughput with tool cost control. Designed for integration and reliable sourcing A total length of 258 mm gives a practical reach for most chucking and toolholding arrangements without excessive overhang, while the robust shank diameter increases clamping rigidity for deeper holemaking tasks. The combination of standard insert geometry and conventional shank dimensions supports straightforward integration into existing tool cabinets and CAM strategies. For purchasers, Metav Werkzeuge provides a consistent supply channel and technical orientation that helps to democratise precision tools across workshops and industry: stable availability from a European distribution base reduces the risk of supply interruptions and supports long‑term planning. Contact Metav Werkzeuge for specification confirmation and to discuss how the Teknik Makina Indexable Insert Drill U793TM can be optimised for existing toolholders and production processes — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: U793TM Manufacturer: Teknik Makina Article type: Indexable insert drill Dimensions & core data Cutting diameter: 33 mm Shank diameter: 32 mm Cutting length: 165 mm Shank length: 58 mm Total length: 258 mm Weight: 1.182 kg Designs & special features Compatible inserts: WCM‑06T3 Compatible insert manufacturer: Korloy Indexable insert system Balanced tool body for reduced vibration FAQ What insert type does this drill use? The drill uses Korloy WCM‑06T3 indexable inserts specified for the Teknik Makina U793TM. What are the key dimensions for toolholder selection? Key dimensions are a 32 mm shank diameter, 58 mm shank length and 258 mm total length, suitable for holders matching a 32 mm shank. How does the indexable concept reduce running costs? By replacing only the worn indexable inserts rather than the entire drill body, the U793TM reduces material costs and shortens maintenance cycles. Is the tool balanced for high‑speed operation? The U793TM is designed with a balanced body and a shank large enough to improve clamping rigidity and reduce vibration during operation. Can standard clamping systems be used with this drill? Yes. The 32 mm shank is compatible with common toolholding systems that accept that nominal diameter. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust drilling solution that combines a large Ø33 mm cutting diameter with quick insert changes and a substantial 66 mm cutting length for productive boremaking; procurement and technical advice are available via Metav Werkzeuge to ensure seamless integration into production. Indexable insert drill U134TM — Ø33 mm, Korloy WCM‑06T3 compatible by Teknik Makina The indexable insert drill U134TM is designed as a precision drilling body for industrial CNC applications, offering a high cutting length-to-diameter ratio and compatibility with Korloy indexable inserts for efficient holemaking. Indexable design for fast insert changes Compatible with Korloy WCM‑06T3 inserts Ø33 mm cutting diameter, high metal removal 32 mm shank for stable spindle clamping Increased productivity through large diameter and long cutting reach The tool body delivers a combination of a Ø33 mm cutting diameter and a 66 mm cutting length, which translates into fewer tool changes for repeated boremaking and longer uninterrupted runs. The insert system (type WCM‑06T3) allows for economical, rapid replacement of cutting edges without regrinding, reducing downtime. With a substantial 159 mm overall length, the design supports both through-hole and shallow deep-hole operations within the limits of the machine setup, helping to maintain cycle-time efficiency in production environments. Reliable clamping and process stability for high-quality bores A robust 32 mm shank and precisely machined seating ensure stable spindle clamping and reduced runout, contributing to consistent bore geometry and surface finish. The tool’s mass (approx. 0.845 kg) aids stable rotation at moderate spindle speeds while the insert geometry from the selected manufacturer promotes predictable chip formation and heat distribution. The indexable arrangement lowers tooling cost per hole since only the inserts require replacement, which improves per-piece cost calculations for medium- and large-batch work. Practical integration and service-ready compatibility Compatibility with Korloy inserts (WCM‑06T3) means straightforward sourcing of cutting edges and predictable performance when paired with recommended grades. The tool is supplied as a serviceable drill body suitable for workshops that standardise on indexable systems and wish to reduce inventory of solid tools. For detailed machining parameters or to confirm fitment with a specific spindle or holder, Metav Werkzeuge’s technical team can provide targeted guidance and ensure the tool meets the operational requirements of the production cell. Contact Metav Werkzeuge for tailored advice on integrating the U134TM into production and for reliable supply from Emmerich; technical data and procurement support are available by email or phone. Technical data Article number: U134TM Manufacturer: Teknik Makina ECLASS: 21180201 Facts Cutting diameter: 33 mm Shank diameter: 32 mm Cutting length: 66 mm Shank length: 58 mm Overall length: 159 mm Weight: 0.845 kg Special features Compatible inserts: WCM‑06T3 Compatible insert manufacturer: Korloy SKU / UID: U134TM FAQ Which inserts fit this drill body? The drill body accepts WCM‑06T3 indexable inserts; Korloy is listed as the compatible insert manufacturer for the U134TM. What is the cutting diameter and overall length? The tool provides a 33 mm cutting diameter and an overall length of 159 mm, giving a 66 mm effective cutting reach for boremaking. What shank size is required for mounting? A 32 mm shank is specified for the tool, ensuring stable clamping in appropriately rated collets or holders. How does the indexable system reduce operating costs? By using replaceable WCM‑06T3 inserts, the cutting edges can be renewed without replacing the entire tool body, lowering per-hole tooling expense for serial production. Is the tool supplied ready to use with inserts fitted? The U134TM is supplied as the drill body; inserts of type WCM‑06T3 must be sourced separately and mounted according to the insert manufacturer's instructions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust, indexable drilling solution that combines precise cutting geometry and easy insert replacement to keep cycle times low; the compatibility with Korloy WCM‑06T3 inserts and a compact shank profile ensure rapid integration into existing toolholders. Order or request technical clarification via Metav Werkzeuge for reliable supply from Emmerich. Vollbohrer — Indexable drill, Ø 33 mm / shank Ø 32 mm by Teknik Makina The Vollbohrer is an industrial indexable drill designed for efficient holemaking in production environments, optimised for use with Korloy WCM‑06T3 inserts and medium‑deep drilling applications. Indexable design for Korloy WCM‑06T3 inserts Ø 33 mm cutting diameter Shank Ø 32 mm, 58 mm clamping length Cutting length 99 mm, overall length 192 mm High productivity through indexable tooling and clear compatibility The indexable configuration delivers a clear productivity advantage: with replaceable WCM‑06T3 inserts the toolhead can be renewed in seconds, reducing machine downtime and tooling cost per hole. For batch production the ability to replace inserts without regrinding means shorter non‑productive times and consistent component quality. The tool’s compatibility with Korloy indexable inserts simplifies procurement and ensures repeatable cutting performance. Precise geometry that supports stable hole quality The combination of a Ø 33 mm cutting diameter and a cutting length of 99 mm is tailored for stable chip evacuation and consistent concentricity. The compact shank Ø 32 mm with a 58 mm clamping length aids toolholder rigidity, which directly reduces run‑out and bore deviation. Reduced vibration and better force distribution translate into more reliable hole tolerances and improved surface finish in serial production. Practical benefits for integration and handling Measured overall length of 192 mm and a sub‑kilogram mass (0.973 kg) make the tool straightforward to handle and store. The axial proportions permit easy clamping in standard holders while keeping reach adequate for medium‑depth operations. The insert system eliminates the need for regrinding and allows for simple inventory management of inserts rather than whole tools, thus lowering total cost of ownership for the workshop. Where this tool adds value on the shop floor In operations where predictable cycle times and minimal set‑up overhead are priorities, the indexable drill provides an economical route to high throughput. The robust construction suits repetitive drilling in steels and general engineering materials where insert changeovers are preferable to complete tool replacement. Combined with disciplined tool management, the solution enhances process reliability across production runs. Contact Metav Werkzeuge for tailored technical advice or to arrange supply directly from our Emmerich facility; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: U176TM Manufacturer: Teknik Makina Designation: Vollbohrer Core technical data Diameter: 33 mm Shank diameter: 32 mm Cutting length: 99 mm Clamping length: 58 mm Overall length: 192 mm Weight: 0.973 kg Special features Compatible inserts: WCM‑06T3 Suitable insert manufacturer: Korloy FAQ What insert type is required for this drill? The drill is designed for WCM‑06T3 indexable inserts and is optimised for use with Korloy insert grades. What are the key dimensions to check for toolholder compatibility? Check the shank Ø 32 mm, the clamping length 58 mm and an overall length of 192 mm to ensure correct seating in the toolholder. Can this drill be used for deep hole machining? The tool’s cutting length of 99 mm makes it suitable for medium‑depth holes; for deeper bores assess chip evacuation and holder rigidity. Which manufacturer produced this tool and what is the SKU? This indexable drill is from Teknik Makina and is listed under SKU U176TM. What is the practical advantage of the indexable design? The indexable design allows fast insert replacement, reducing downtime and lowering per‑hole tooling costs compared with regrindable solid tools. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a robust indexable design and an extended cutting length that together boost productivity and repeatable hole quality; order the tool directly via Metav Werkzeuge or consult our specialists for application advice. Vollbohrer — Indexable solid drill Ø33 mm, 99 mm cutting length (Teknik Makina) A Vollbohrer designed for indexable inserts, offering deep cutting capacity and secure clamping for demanding metalworking operations Solid indexable design for repeatable performance Compatible with SPMG 0904 indexable inserts Ø33 mm diameter with 99 mm cutting length Robust 32 mm shank for secure clamping Increased throughput through indexable cutting geometry The indexable concept delivers rapid material removal with fewer full-tool changes, translating into measurable productivity gains on the shop floor. With a 99 mm cutting length and an external diameter of Ø33 mm, this indexable solid drill is configured for extended penetration depths while preserving chip control and coolant access. The use of replaceable SPMG 0904 inserts keeps downtime to a minimum and reduces per-hole cost compared with solid single-piece tools, making the tool a pragmatic choice for repetitive drilling tasks. Rigidity and clamping for consistent hole quality Designed with a 32 mm shank and a shank length of 58 mm, the tool offers high axial stability in standard holders, which reduces vibration and improves positional accuracy. The overall length of 192 mm and a mass of 0.92 kg balance reach with stiffness, supporting stable cutting even under intermittent heavy feeds. This mechanical stability directly benefits surface finish and roundness in drilled holes, so process engineers can rely on reproducible results across production runs. Compatibility and workshop convenience to cut operating costs Compatibility with leading insert manufacturers Taegutec and YG-1 ensures access to a broad range of grade and geometry options for varying workpiece materials and cutting conditions. The modular concept simplifies reconditioning: worn inserts are replaced rather than the entire tool body, reducing inventory cost and waste. Supplied items are supported via Metav Werkzeuge’s European logistics hub, which acts as a quality filter and offers straightforward order handling and dependable replenishment for professional workshops. For precision, durability and fast availability, contact Metav Werkzeuge to source the Teknik Makina Vollbohrer (SKU U833TM) and confirm insert choices and delivery times. Technical data SKU: U833TM Manufacturer: Teknik Makina Diameter: 33 mm Overall length: 192 mm Cutting length: 99 mm Shank diameter: 32 mm Shank length: 58 mm Weight: 0.92 kg Insert type: SPMG 0904 Compatible insert manufacturers: Taegutec, YG-1 Product type: Indexable solid drill FAQ Which inserts fit this indexable solid drill? The drill accepts SPMG 0904 inserts; compatible manufacturers listed are Taegutec and YG-1 for the Teknik Makina Vollbohrer (SKU U833TM). What are the principal dimensions to consider for holder selection? Key dimensions: Ø33 mm diameter, 32 mm shank diameter, 58 mm shank length and 192 mm overall length. How deep can the tool cut effectively? The effective cutting length is 99 mm, which defines the standard maximum engagement depth for continuous drilling operations. Is the shank compatible with standard clamping systems? The 32 mm shank diameter is intended for holders and chucks designed to accept a 32 mm shank; confirmation with the specific clamping system is recommended. Can inserts be sourced from multiple manufacturers? Yes, inserts from Taegutec or YG-1 are compatible with the Teknik Makina Vollbohrer (U833TM), allowing choice of grade and geometry for different applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust 25 mm shank, 50 mm cutting height and compatibility with 4C indexable inserts for precise parting and grooving operations; order the tool through Metav Werkzeuge or consult our specialists for configuration assistance. Teknik Makina Stechklemmhalter K654TM — parting and grooving clamp holder with 25 mm shank and 4 mm cutting width Teknik Makina Stechklemmhalter K654TM is a dedicated parting and grooving clamp holder designed for stable insert clamping in CNC lathes and turning centres, optimised for short-chipping and reliable repeatability. Robust 25 mm shank for secure mounting 50 mm cutting height for deep grooves 4 mm cutting width for fine parting operations Compatible with 4C indexable inserts Stable clamping for consistent parting quality The holder delivers a secure clamp for indexable inserts compatible with the 4C system, combining a rigid tool body with a compact interface. The 25 mm shank diameter provides a solid connection to standard tool posts and boring bars (designation S25R), reducing vibration and runout during cuts. For production environments this means fewer rejected parts and improved process repeatability. The clamping geometry supports a precise insert seat, so cutting width of 4 mm can be achieved reliably without rework. Faster setup and predictable tool behaviour Designed with workshop efficiency in mind, the holder’s 200 mm overall length and standard shank form enable quick changeovers and predictable tool projection. The combination of a defined cutting height of 50 mm and matched insert seating reduces the need for frequent manual adjustments; set-up times are shortened and cycle consistency increases. Technical novices will find the principle straightforward: a correctly sized shank and matched insert type ensure the insert tip is aligned to the machine’s datum, improving first-pass accuracy. Built for daily workshop demands Constructed to withstand regular use, the component balances mass and rigidity—total weight around 0.764 kg—for controlled dynamics without unnecessary bulk. The holder accepts 4C-style inserts and works with compatible boring-bar designs (notably S25R and related holders), which means replacement inserts are widely available and change-out is simple. The robust build supports high repeatability in medium-duty parting and grooving applications, contributing to lower downtime and a steadier production flow. For reliable parting and grooving performance, contact Metav Werkzeuge for tailored advice or to arrange procurement through our Emmerich hub — email info@metav-werkzeuge.com or call +49 2822 7131930 for specialist guidance and order support. Technical Data Article number: K654TM Manufacturer: Teknik Makina Brand: Teknik Makina SKU: K654TM Facts Shaft diameter: 25 mm Cutting height: 50 mm Cutting width: 4 mm Overall length: 200 mm Weight: 0.764 kg Diameter (tool body): 33 mm Insert type: 4C Boring-bar designation: S25R Secondary holder designation: 4C-R S224 Special features Compatible with 4C indexable inserts Rigid clamping geometry for reduced runout Standard shank for conventional tool posts Designed for parting and grooving operations FAQ What insert type fits this parting clamp holder? The parting clamp holder accepts 4C indexable inserts; the tool is tailored to 4C seating and clamping for stable cutting performance with Teknik Makina K654TM. Which shank diameter is required for mounting? Mounting requires a 25 mm shank diameter interface (S25R compatibility), ensuring a secure fit in standard tool posts and boring-bar adaptors for the Teknik Makina K654TM holder. What cutting dimensions can be expected from this holder? The holder is specified for a cutting width of 4 mm and a cutting height of 50 mm, making it suitable for precise parting and narrow grooving tasks with consistent chip control. Is the holder suitable for high-speed applications? The tool is designed for stable clamping and repeatable geometry; for high-speed use, consult machining parameters and Teknik Makina recommendations to confirm feed and speed limits for the chosen insert type and machine. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust 25 mm shank, a precise 4 mm cutting width and full compatibility with ZCC 4C ZT.D inserts to keep turning operations predictable and productive; order directly via Metav Werkzeuge or consult the team for specification support. Parting and grooving clamp holder K684TM — 25 mm shank, 4 mm cutting width (Teknik Makina) A compact parting and grooving clamp holder designed for precise turning tasks and compatible with ZCC 4C ZT.D indexable inserts. 25 mm shank for secure mounting Compatible with ZCC 4C ZT.D inserts 4 mm cutting width for precise grooves 200 mm overall length for deeper cuts Consistent parting performance through rigid design The holder delivers consistent results thanks to a 25 mm shank and a robust body that reduce vibration during cut-off and grooving operations. The combination of secure clamping and a defined cutting height of 35 mm supports repeatable geometry and reduces scrap rates in batch production. For workshops aiming to increase first-pass quality, the rigid construction of the holder contributes to steady tool life and predictable surface finish, helping to lower rework and improve throughput. Insert compatibility and straightforward set-up Engineered for use with ZCC 4C ZT.D inserts and identified by the ISO-style designation S25R, the tool accepts common clamping bars such as 4C-R ZT.D, enabling rapid replacement and minimising machine downtime. Clear compatibility with established insert systems simplifies stock management and makes the holder a practical choice for mixed-production environments. The straightforward interface with standard inserts reduces set-up time on the lathe and supports a smoother production flow. Accurate groove geometry with controlled cut parameters With a defined cutting width of 4 mm and a cutting height of 35 mm, the holder is optimised for narrow groove and parting tasks where dimensional control matters. The nominal overall length of 200 mm and external diameter of 33 mm provide reach for deeper operations while maintaining rigidity close to the workpiece. Such geometry helps to maintain dimensional tolerances and minimise thermal or elastic deformation during extended cycles, which is vital for repeatable batch performance. Practical workshop benefits and reliability Weighing in at 1.578 kg and built by Teknik Makina, the unit is a reliable addition to tool sets used in conventional and CNC turning. Compatibility with ZCC inserts and an ISO-compatible shank designation mean easier procurement and integration into existing tooling families. For purchasers seeking a balance of mechanical stability, straightforward maintenance and proven compatibility, this clamp holder supports efficient production and a lower total cost of operation through reduced set-up complexity. For specification advice or to place an order for Teknik Makina tooling, contact Metav Werkzeuge for personal consultation and delivery details. Technical data Article number: K684TM Manufacturer: Teknik Makina Compatible insert designation: 4C ZT.D Compatible insert manufacturer: ZCC Holder shank ISO: S25R Core specifications Shank diameter: 25 mm Cutting height: 35 mm Cutting width: 4 mm Overall length: 200 mm External diameter: 33 mm Weight: 1.578 kg Features / Versions Clamping bar designation: 4C-R ZT.D Application: parting and grooving Robust construction for reduced vibration Designed for rapid insert replacement FAQ Which inserts are compatible with this holder? The holder is compatible with ZCC standard inserts of the 4C ZT.D family; the clamping bar designation is 4C-R ZT.D. What shank and ISO designation does the tool use? The tool uses an ISO-style shank designated S25R with a 25 mm shank diameter, sold under SKU K684TM by Teknik Makina. What cutting dimensions does the holder support? The clamp holder is designed for a cutting width of 4 mm and a cutting height of 35 mm, suitable for narrow grooves and parting operations. Is the length suitable for deeper parting applications? With an overall length of 200 mm and an external diameter of 33 mm, the holder offers additional reach for deeper operations while prioritising rigidity. How heavy is the holder? The tool has a mass of 1.578 kg, reflecting its solid construction for stable cutting performance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of compatibility with CCMT 09T3 indexable inserts, internal coolant and a robust 32 mm shank to maintain stable production and minimise rework; order directly via Metav Werkzeuge or consult our technical team for application-specific guidance. T-Nut Fräser — 33 mm T‑slot cutter with internal coolant by Teknik Makina The T-Nut Fräser is a precision T‑slot cutter designed for machining accurate T‑slots using CCMT 09T3 indexable inserts in CNC milling and fixture manufacture. *33 mm diameter for medium‑sized T-slots *Internal coolant for improved chip evacuation *32 mm robust shank for stable clamping *Compatible with CCMT 09T3 indexable inserts Delivering repeatable slot geometry for reliable assembly A stable toolholder and consistent cutter geometry reduce corrective machining and assembly delays. The combination of a 32 mm shank and a well‑balanced head ensures low runout and consistent engagement, which translates into better tolerance control. Fitted with CCMT 09T3 indexable inserts, the cutter offers predictable cutting behaviour and simple insert changes, enabling straightforward restoration of cutting performance without complex regrinding procedures. Coolant‑through design that improves tool life and process uptime The integrated internal coolant channel directs cutting fluid precisely to the cutting zone, aiding chip evacuation and reducing thermal load on the insert edges. This targeted cooling lowers flank wear and extends the useful life of cutting edges, while also supporting higher metal removal rates where process conditions allow. Using coolant effectively reduces built‑up edge and improves surface finish, helping to keep machining cycles consistent and downtime to a minimum. Modular maintenance and secure clamping for efficient production With only two cutting edges and a simple Torx T15 fastening system (screw M3.5×8.5), insert replacement is rapid and repeatable, decreasing tool change time on the shop floor. The tool’s overall design, including a 135 mm overall length and a dedicated 65 mm cutting length, suits inline tool management and inventory control. The model SKU TKC160TM is supplied by Teknik Makina and integrates smoothly into modular tooling strategies, supporting a predictable spare‑parts approach and controlled tooling costs. Discuss application requirements with Metav Werkzeuge for an optimised tool set‑up or request tailored technical advice on Teknik Cutting Tools' T‑slot cutters like the TKC160TM by contacting Metav Werkzeuge directly Technical data SKU: TKC160TM Product type: T-slot cutter Brand: Teknik Makina Label: 33mm T-Nut Fräser CCMT 09T3 L135mm mit Innenkühlung Facts Diameter: 33 mm Overall length: 135 mm Weight: 0.678 kg Shank diameter: 32 mm Cutting length: 65 mm Cutting edges: 2 Special features Internal coolant Compatible with CCMT 09T3 indexable inserts Torx key T15 Torx screw M3.5×8.5 FAQ Which inserts are compatible with this cutter? The cutter accepts CCMT 09T3 indexable inserts; the modular design facilitates fast insert replacement and consistent cutting geometry. Does the tool support coolant‑through operation? Yes, the tool features internal coolant which directs fluid to the cutting zone for improved chip evacuation and tool life. What shank size is required for the holder? The tool has a 32 mm shank, designed for robust clamping in standard heavy‑duty holders to ensure minimal runout. How are the inserts secured and replaced? Inserts are fixed using a Torx T15 screw (M3.5×8.5), allowing quick and repeatable replacement with common workshop tools. What is the product SKU for ordering or stock control? The item is listed as TKC160TM, which identifies the 33 mm T‑slot cutter with internal coolant from Teknik Makina Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust combination of 33 mm cutting diameter, internal coolant and a firm 32 mm shank to achieve consistent T-slot quality and reduced tooling costs; order this cutter via Metav Werkzeuge or consult our specialists for tailored machining recommendations. T-slot cutter TKC162TM — 33 mm diameter, internal coolant, for CCMT 09T3 indexable inserts The T-slot cutter TKC162TM is a CNC milling tool designed for machining precise T-slots using CCMT 09T3 indexable inserts, offering stable clamping and reliable coolant delivery for longer tool life 33 mm diameter for deep T-slots Internal coolant for improved chip evacuation Compatible with CCMT 09T3 indexable inserts 32 mm shank for stable clamping Consistent slot geometry through replaceable inserts and sturdy design The cutter combines a 33 mm diameter with a geometry optimised for T-slot profiles, enabling stable material removal with minimal rework. By accepting CCMT 09T3 indexable inserts, the milling tool allows fast insert changes and predictable cutting performance, which reduces downtime and lowers per-part tooling cost. The use of replaceable carbide inserts means edge quality can be restored without regrinding the body, translating into continuous production and repeatable slot dimensions. Improved cooling and chip control for longer cutting intervals Built-in internal coolant supplies cutting fluid directly to the insert area, supporting heat dissipation and helping to clear chips from the slot cavity. This targeted coolant feed reduces thermal loading on the cutting edge and improves surface finish, particularly in deeper or narrow T-slots. Better chip evacuation also lowers the risk of recutting swarf, enhancing tool life and preserving dimensional accuracy over extended runs. Secure clamping and straightforward maintenance for efficient setups A 32 mm shank and a total length of 180 mm provide the rigidity needed for stable milling, while a 65 mm cutting length offers the reach required for common T-slot depths. The assembly uses a T15 Torx key and M3.5x8.5 Torx screws, enabling quick insert changes and secure fixation. With two cutting edges per head, the tool balances material removal with smoothness of cut, making it suitable for workshop and production contexts where consistent results and straightforward serviceability matter Contact Metav Werkzeuge for an expert assessment of machining parameters or to arrange supply of the Teknik Makina T-slot cutter equipped with internal coolant; eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data SKU: TKC162TM Manufacturer: Teknik Makina Data Diameter: 33 mm Total length: 180 mm Shank diameter: 32 mm Cutting length (shaft): 65 mm Number of cutting edges: 2 Weight: 0.947 kg Special features For inserts: CCMT 09T3 Inner cooling: Yes Torx key: T15 Torx screw: M3.5x8.5 FAQ What insert type is required for this cutter? The cutter is designed for CCMT 09T3 indexable inserts, which provide economical replacement and consistent cutting geometry for T-slot milling. Is the cutter suitable for deep T-slots in production environments? Yes, the combination of a 33 mm diameter, a 65 mm cutting length and internal coolant makes the tool appropriate for deeper T-slot operations in a production setting. How is coolant delivered to the cutting edge? Coolant is supplied through the tool body via internal coolant, directing fluid to the insert seat to aid heat control and chip evacuation. What shank size is required for secure clamping? A 32 mm shank ensures stable clamping in standard toolholders and helps reduce vibration during milling cycles. Which fastener is used to secure the inserts? Inserts are fixed with M3.5x8.5 Torx screws, tightened using a T15 Torx key for reliable and repeatable fixation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a rigid 25 mm shank and a precise 4 mm cutting width to keep parting operations stable and repeatable; the 200 mm overall length gives the reach needed for many turning setups. Order the holder via Metav Werkzeuge or consult our specialists for application advice. Parting Clamp Holder K630TM – 25 mm shank, 4 mm cutting width (Teknik Makina) The Parting Clamp Holder K630TM is a compact, rigid tool holder designed for grooving and parting on lathes and CNC turning centres. Robust 25 mm shank for stable cutting Compatible with 4C indexable inserts 4 mm maximum cutting width 200 mm overall length for extended reach Consistent parting accuracy through rigid shank support A stable tool blank is essential for accurate parting and grooving. The holder’s 25 mm shank and substantial support area minimise deflection during cut, which reduces chatter and produces a cleaner parting face. With a 34 mm external diameter and a precise clamping arrangement, the unit maintains repeatable engagement with the insert. This mechanical stability results in fewer rework cycles and a more reliable production flow for repetitive turning tasks. Fast insert compatibility and clear clamping geometry Compatibility with 4C indexable inserts makes routine tool changes swift and predictable. The design accepts standard 4C plates and the clamping system is engineered to secure the insert with minimal axial play. The 50 mm cutting height provides correct seating and support for the insert, ensuring consistent chip control while reducing the chance of premature edge failure. For workshops that value predictable maintenance intervals, this combination lowers downtime and supports efficient tool management. Built for production: reach, balance and vibration control An overall length of 200 mm offers the reach needed for deeper grooving and parting operations without excessive overhang. At 0.768 kg, the holder provides a balance between rigidity and manageable mass, helping to dampen vibrations without becoming cumbersome to handle. These physical characteristics are particularly useful in serial production environments, where reduced vibration extends insert life and improves surface finish — a tangible efficiency gain across batches. Simple integration into standard turning setups The holder carries the ISO-style designation S25R, while the clamping variant is referenced as 4C-R S229, aiding compatibility checks with existing tool posts and turrets. The part integrates easily into common tool stations and is suited to conventional and CNC lathes that accept a 25 mm shank. Clear, standardised references reduce setup time and help workshop planners match the holder to the correct insert and machine interface without guesswork. Discuss machining requirements with Metav Werkzeuge or request tailored application advice from our Emmerich team to confirm fitment and optimise insert selection for the Teknik Makina K630TM Parting Clamp Holder Technical Data SKU: K630TM Manufacturer: Teknik Makina Product name: Parting clamp holder (Stechklemmhalter) Numbers / Core technical data Shank diameter: 25 mm Cutting height: 50 mm Cutting width: 4 mm Overall length: 200 mm Outer diameter: 34 mm Weight: 0.768 kg Design / Special features Compatible insert type: 4C Shank designation: S25R Holder designation: 4C-R S229 FAQ Which insert type fits this holder? The holder accepts 4C indexable inserts; the clamping geometry is specified for the 4C series and is referenced by the holder designation 4C-R S229. What is the maximum cutting width for grooving? The maximum recommended cutting width is 4 mm, defined by the tool’s cutting-edge clearance and clamping arrangement. Is the holder suitable for CNC turning centres? Yes, the Parting Clamp Holder K630TM is intended for use in both manual lathes and CNC turning centres that accept a 25 mm shank and ISO-style shank codes such as S25R. How does the overall length affect stability? The 200 mm overall length provides reach for deeper operations but should be balanced against potential overhang; the holder’s mass and rigidity help control vibration in typical turning conditions. What mounting reference should be checked before ordering? Confirm the machine’s tool post or turret accepts a 25 mm shank (S25R) and ensure the insert type 4C is compatible with existing tool management. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a 340 mm cutting capacity with compatibility for CCMT 1204 indexable inserts and a compact 208 mm overall length delivers efficient large-bore machining with reduced setup time and straightforward maintenance – ideal for production runs and repair work. Order the tooling directly via Metav Werkzeuge or consult our specialists for application advice. Boring tool for CCMT 1204 indexable inserts – 340 mm cutting diameter, 208 mm overall length (Teknik Makina) The boring tool for CCMT 1204 indexable inserts is a robust, purpose-built solution for large internal diameters on lathes and turning centres, designed to accept standard CCMT 1204 inserts for flexible, low-downtime machining. Compatible with CCMT 1204 indexable inserts 340 mm cutting diameter 208 mm overall length Engineered for reliable large-bore machining The design combines a large nominal diameter of 340 mm with proven compatibility for CCMT 1204 indexable inserts to enable stable, repeatable internal machining. This configuration reduces the need for specialised single-edge tools by allowing the use of standard inserts, which shortens downtime for edge changes and keeps inventory simple. The result is a practical balance between rigidity and accessibility for medium to heavy bore turning operations in production and maintenance workshops. Maintenance and insert handling for productive shifts Using indexable inserts means that cutting edges are replaced quickly without regrinding, contributing to predictable cycle times and lower per-part tooling costs. The tool’s 208 mm overall length keeps overhang acceptable for many turning centres, improving vibration resistance and surface finish consistency. Clear compatibility with CCMT-format inserts simplifies procurement and allows established grades to be selected for steel, castings or alloy workpieces, depending on the insert chosen. Integration into the workshop and process benefits The modular nature of the system supports standard workshop workflows: familiar insert geometry (CCMT 1204) makes selection straightforward, while the tool’s nominal dimensions facilitate programming and setup on conventional machine controls. For purchasing managers and shopfloor engineers, the combination of a high cutting diameter, standardised insert format and compact overall length delivers both flexibility and reduced logistical overhead, reinforcing predictable throughput in mixed-batch production. For procurement advice, technical clarification or to order the Teknik Makina TKB162TM boring tool contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for prompt, expert support. Technical data Article number: TKB162TM Product: Boring tool for CCMT 1204 indexable inserts Manufacturer: Teknik Makina Facts Nominal diameter: 340 mm Max cutting diameter: 450 mm Overall length: 208 mm eClass: 21181208 Special features Compatible inserts: CCMT 1204 Product type: Boring tool Label: 340mm Ausbohrwerkzeug CCMT 1204 L208mm SKU: TKB162TM FAQ What insert format does this boring tool accept? The tool is designed for CCMT 1204 indexable inserts; using the specified insert format ensures correct seating, cutting geometry and expected performance for the Teknik Makina TKB162TM boring tool. What are the nominal and maximum cutting diameters? Nominal cutting diameter is 340 mm and the data sheet notes a maximum cutting diameter value of 450 mm, enabling selection of the appropriate set-up for the intended bore. Is the overall length suitable for standard lathes? With an overall length of 208 mm, the TKB162TM is suited to many turning centres where moderate overhang and rigidity are required; machine capability and clamping should be checked prior to operation. Can standard CCMT grades be used for different materials? Yes; the tool accepts standard CCMT 1204 inserts, allowing selection of insert grades optimised for steel, cast iron or non-ferrous materials to match the machining task. How does using indexable inserts affect workshop efficiency? Indexable inserts reduce downtime for edge changes and simplify inventory by using standardised inserts, which supports predictable cycle times and easier reconditioning workflows. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, indexable-insert solution that combines high repeatability, straightforward maintenance and efficient chip control; the measurable benefits are reduced set-up time and consistent chamfer quality. Order the chamfer cutter directly via Metav Werkzeuge or contact the consultants for application advice. Chamfer cutter S345TM – indexable-insert chamfering cutter, Ø 34 mm (Teknik Makina) Chamfer cutter S345TM is a robust indexable-insert tool designed for precise chamfering operations in machining centres and milling machines, suitable for use with standard TCMT 16T3 inserts. Ø 34 mm cutting diameter for broad edges Compatible with TCMT 16T3 indexable inserts 20 mm cylindrical shank for standard holders 30° and 60° chamfer angles for versatile chamfering Consistent chamfer quality with indexable inserts The indexable design ensures repeatable chamfer geometry and fast recovery time after insert changes. With a 34 mm nominal diameter and 40 mm cutting height, the cutter delivers a stable machining platform for chamfers and deburring operations. The use of TCMT 16T3 inserts provides straightforward tool management: worn inserts are replaced rather than re-sharpened, reducing downtime and keeping the production line moving. This configuration supports efficiency improvements in batch production where reproducibility is essential. Reduced set-up complexity and secure clamping A 20 mm shank permits secure mounting in standard collet chucks and toolholders, while the supplied M3.5×8.5 Torx screw (Torx key T15) secures the insert reliably under cutting loads. The double-angled design (available 30° / 60°) enables the selection of the most suitable chamfer geometry without multiple tools, saving tool-change time and simplifying tool inventory. The cutter’s modest weight (0.307 kg) and balanced construction minimise spindle wear and support stable surface finishes. Designed for workshop integration and predictable throughput The modular indexable-insert concept aligns with lean workshop processes: predictable tool life, fewer regrinds and quicker interventions at the machine. The cutter’s compatible insert size and common Torx fastener mean replacement parts are widely available, aiding uninterrupted production flow. For procurement managers and workshop supervisors this tool represents a pragmatic choice where uptime and standardisation across multiple machines are priorities, rather than exotic single-use solutions. Contact Metav Werkzeuge today to discuss how the Teknik Makina Chamfer Cutter S345TM fits into existing tool sets and to arrange delivery from Emmerich; Metav Werkzeuge’s consultants can advise on holder compatibility and insert selection Technical data Article number: S345TM Brand: Teknik Makina Insert type: TCMT 16T3 Core dimensions Cutting diameter: 34 mm Shank diameter: 20 mm Cutting height: 40 mm Overall length: 100 mm Number of cutting edges: 2 Weight: 0.307 kg Features & compatibility Chamfer angles: 30° and 60° Torx screw: M3.5x8.5 Torx key size: T15 Indexable-insert system FAQ Which inserts fit this chamfer cutter? The chamfer cutter S345TM from Teknik Makina is designed for TCMT 16T3 indexable inserts. What shank diameter is required for mounting? The tool has a 20 mm cylindrical shank, compatible with standard collet chucks and holders that accept a 20 mm shank. What chamfer angles are available with this cutter? This cutter is configured for both 30° and 60° chamfering applications, enabling flexible edge geometries. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid tool that combines a 34 mm cutting diameter, a 25 mm shank for increased stability and quick indexable insert changes for continuous chamfering operations; order the cutter via Metav Werkzeuge or consult the Metav team for application advice. Chamfer mill S339-1TM — chamfer cutter for TCMT 16T3 indexable inserts (34 mm, 25 mm shank) S339-1TM is a purpose-built chamfer mill for industrial shaft tooling, optimised for repeatable chamfers using TCMT 16T3 indexable inserts. Chamfer mill for TCMT 16T3 inserts 34 mm cutting diameter for wider chamfers 25 mm shank for high rigidity Two cutting edges for smooth finishes Enhanced rigidity for consistent chamfering A solid toolholder connection is essential for predictable results. The 25 mm shank delivers elevated torsional stiffness, reducing chatter and dimensional variation when machining chamfers. Compatibility with TCMT 16T3 indexable inserts allows fast reconditioning of the cutting edge: worn inserts are replaced rather than the entire cutter, cutting downtime and consumable costs. The combination of a 34 mm diameter and a compact overall length provides a balance between reach and stability for many workshop setups. Efficient cutting and reliable surface quality Designed with two cutting edges, the cutter achieves efficient material removal while maintaining a controlled cutting force that helps to produce even chamfer profiles. A 40 mm cutting length grants sufficient engagement for stepped or multi-level chamfers, while the 100 mm overall length supports access in deeper set-ups. The modest mass (approx. 0.378 kg) contributes to smooth acceleration on CNC spindles and helps to dampen high-frequency vibration, supporting improved surface finish without complex toolpath adjustments. Practical mounting and maintenance for production use Secure mounting is achieved via the included Torx fastening: T15 key access and an M3.5x8.5 Torx screw ensure repeatable clamping of the insert seat, eliminating play between the insert and the body. The indexable system simplifies inventory management—only inserts and Torx screws are regularly exchanged—while the tool body remains in service, aligning with lean maintenance practices. The model is supplied as SKU S339-1TM and is suitable for integration into standard shaft-milling toolholders classified under shaft cutters. Contact Metav Werkzeuge for tailored application advice and a personalised quotation for the Teknik Makina S339-1TM chamfer mill — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: S339-1TM Label: 34mm Fasenfräser TCMT 16T3 L100mm ECLASS: 21180806 Manufacturer: Teknik Makina Product type: Chamfer mill Facts Diameter: 34 mm Overall length: 100 mm Shank diameter: 25 mm Cutting length: 40 mm Cutting edges: 2 Weight: 0.378 kg Torx key: T15 Torx screw: M3.5x8.5 Special features For TCMT 16T3 indexable inserts Indexable insert mounting for fast replacement Designed as a shaft-mounted chamfer cutter Robust Torx clamping for secure seating FAQ How are the inserts secured in this chamfer mill? The inserts are fastened with an M3.5x8.5 Torx screw (T15) to the seat; the S339-1TM uses the standard TCMT 16T3 indexing form for straightforward insert changes. What shank diameter and toolholder compatibility does it offer? The tool features a 25 mm shank, suitable for standard shaft toolholders used in milling and CNC applications where a solid clamping interface is required. What chamfer size does a 34 mm diameter support? A 34 mm cutting diameter facilitates wider chamfers and provides stable engagement; the actual chamfer width depends on insert geometry and axial depth of cut. How many cutting edges are fitted and what is the benefit? The cutter uses two cutting edges, which balance material removal rate and surface finish, helping to reduce cutting forces and improve chamfer uniformity. Is this cutter suitable for production runs with frequent insert changes? Yes, the indexable insert system and Torx fastening are tailored for fast, repeatable insert replacement, making the S339-1TM appropriate for production environments. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com