Take advantage of the HSS‑Co PM core and ALCRONA coating for reliable wear resistance and improved tool life; the short, centre‑cutting design and Weldon shank deliver high rigidity and secure clamping for precise finishes — order via Metav Werkzeuge or consult our specialists for application advice. TECWERK short HSS‑Co PM end mill 6 mm, ALCRONA‑coated (DIN 844, Type HR) The TECWERK short HSS‑Co PM end mill 6 mm is a centre‑cutting, four‑flute cutter engineered for high‑rigidity milling of steels, stainless steels and cast components in confined setups. HSS‑Co PM for enhanced toughness and heat resistance ALCRONA coating for higher wear protection Centre‑cutting 4‑flute geometry for plunge capability Weldon shank with drive flat for reliable clamping High‑performance material and coating for longer tool life The combination of HSS‑Co PM (powder‑metallurgy high‑speed steel) and the ALCRONA surface finish provides a balance of toughness and thermal resistance that is especially beneficial under interrupted cuts and elevated temperatures. Meeting DIN 844 specifications, this short cutter offers consistent edge strength and predictable wear patterns, which supports stable cycle times and fewer premature tool changes. The engineered coating reduces built‑up edge and extends the service interval of the tool, leading to measurable process reliability. Short design and flute geometry that improve stiffness and accuracy A compact overall length and a conical flute root increase the cutter’s rigidity, reducing deflection during side milling and finishing passes. With a cutting length of 4 mm and an effective length of 19 mm, the geometry is tailored to minimise vibration in tight fixtures. The 4‑flute layout balances chip evacuation with increased cutting edge count for finer surface finish, while the Weldon style cylindrical shank with drive flat ensures secure axial and torsional location in the toolholder for repeatable positioning. Application range and machining benefits Designed for workpieces up to approximately 1400 N/mm² tensile strength, the tool is very well suited to machining steels, stainless steels and cast iron, while non‑ferrous metals and special alloys are conditionally machinable depending on process parameters. The centre‑cutting capability allows plunge milling or spot drilling without pre‑drilled starts, enabling flexible toolpaths in small‑batch production and repair work. This concentrated applicability reduces tool inventories by providing a versatile short cutter for both roughing reliefs and fine finishing. Practical handling, clamping and process considerations Right‑hand cutting action and the compact configuration make this cutter well matched to short overhangs and rigid setups; correct clamping of the Weldon shank and a secure holder are essential to exploit the tool’s stiffness. Regular inspection of flank wear and coating condition preserves surface quality and helps predict regrinds. Adopting the cutter in process chains stabilises finish quality and reduces rework, contributing to more efficient throughput and lower process variability. Choose the TECWERK ALCRONA‑coated HSS‑Co PM end mill for durable, accurate short‑reach milling and contact Metav Werkzeuge for tailored application guidance or to request availability (SKU 2000866055NW) Technical data Article number: 2000866055NW SKU / UID: 2000866055NW Manufacturer: TECWERK Facts Diameter: 6 mm Overall length: 57 mm Cutting length: 4 mm Effective length: 19 mm Shank diameter: 6 mm Flutes: 4 Free relief: 5.5 mm Cutting direction: right‑hand cutting Standard: DIN 844 Special features Material: HSS‑Co (powder metallurgy) Coating: ALCRONA Type: short, Type HR, 4‑cutting edges Centre‑cutting for plunge capability 45° protection chamfer Cylindrical shank with drive flat (Weldon) Conical flute root for improved rigidity Suitable for steels, inox and cast iron (very good) Conditionally suitable for non‑ferrous and special alloys Designed for workpiece tensile strength up to approx. 1400 N/mm² FAQ Is this cutter suitable for plunge milling? The cutter is centre‑cutting and therefore suitable for plunge milling; the centre‑cut geometry on the TECWERK short HSS‑Co PM end mill allows controlled axial entry into the workpiece. Which materials are best machined with this tool? This short, ALCRONA‑coated HSS‑Co PM cutter performs very well in steels, stainless steels and cast iron, while non‑ferrous metals and specialised alloys are conditionally suitable depending on cutting data. How does the Weldon shank benefit the setup? The Weldon style cylindrical shank with a drive flat provides secure clamping and repeatable torsional location, reducing the risk of slippage in high‑torque operations. What advantage does the short version offer compared with a long cutter? The shorter overhang increases stiffness and reduces chatter, improving dimensional accuracy and surface finish in confined or heavily supported setups. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from the combination of HSS‑Co5 construction, four‑flute geometry and a secure Weldon shank to maintain process reliability and consistent part quality; order the TECWERK end mill directly via Metav Werkzeuge or ask our consultants if needed TECWERK End mill DIN 844 Type HR, HSS‑Co5, D 6 mm, Weldon shank A TECWERK end mill designed for short, high‑precision milling and light plunge work in steel and cast components, ideal for workshop and industrial applications HSS‑Co5 material for improved wear resistance Four‑flute geometry for refined surface finish Weldon shank with drive flat for secure clamping Centre‑cutting for limited plunge capability Precision and durability for everyday production The combination of HSS‑Co5 high‑speed steel and the DIN 844 Type HR specification offers a robust tool for general milling tasks where repeatable performance matters. The tool’s four‑flute geometry reduces vibration and produces a finer surface finish compared with fewer‑flute cutters, while the short overall length supports rigidity in handheld and machine tool set‑ups. These design choices result in lower tool deflection and more consistent part tolerances in series work. Controlled cutting action for steel and cast materials Engineered with a centre‑cutting geometry and right‑hand cutting helix, the cutter enables limited plunging and reliable axial engagement. The effective cutting length of 19 mm combined with a compact profile yields improved chip evacuation in interrupted cuts and better heat management. According to the tool data, the cutter is particularly well suited to steel and cast iron applications, supporting efficient material removal up to the specified strength ranges. Secure fixation and straightforward tool changes A Weldon shank with drive flat ensures positive torque transmission and simple tool changes in milling holders and collet chucks that accept Weldon‑style clamping. The tool’s 6 mm shank diameter and standard cylindrical shank form allow compatibility with common toolholders, reducing setup time. The short design and shank form enhance concentricity and reduce runout, which contributes to a longer service life under repetitive production cycles. Special geometries that aid surface quality and chip control The cutter features a relief‑ground fine profile and a 45° protective chamfer at the entry to protect the cutting edges during engagement. A small relief zone of 5.5 mm helps to maintain clearance behind the cutting edges, improving chip flow and reducing rubbing. These geometry details are valuable when finishing features where surface integrity and dimensional accuracy are priorities, and they make the tool a dependable choice for small to medium batch runs. Contact Metav Werkzeuge for availability of the TECWERK HSS‑Co5 end mill and ensure steady supply from Emmerich for your workshop needs Technical Data Article number: 2000866490NW Label: Schaftfräser DIN 844 Typ HR D.6mm Einsatz‑L.19mm HSS‑Co5 Weldon TW Manufacturer: TECWERK Product type: End mill Norm: DIN 844 Facts Diameter: 6 mm Overall length: 57 mm Effective length: 19 mm Cutting length: 4 mm Number of cutting edges: 4 Relief grind: 5.5 mm Special features Material: HSS‑Co (HSS‑Co5) Type HR, short design Four‑flute geometry Weldon shank with drive flat 45° protective chamfer Centre‑cutting Right‑hand cutting Cylindrical shank with drive flat Relief‑ground fine profile Suitable for steels (very well), cast iron (very well), non‑ferrous metals (limited) Recommended for workpiece strengths up to approx. 800 N/mm² uncoated and up to 1200 N/mm² with coating FAQ What materials is this cutter best suited for? The TECWERK end mill (SKU 2000866490NW) is stated to be very well suited for steel and cast iron, with conditional suitability for non‑ferrous metals. Can this tool perform plunge milling? Yes, the centre‑cutting geometry permits limited plunge operations; the tool is primarily intended for milling with axial engagement as described for DIN 844 Type HR cutters. Which shank system is used and how is it clamped? The cutter uses a Weldon shank with a drive flat, allowing secure clamping in Weldon‑compatible holders and straightforward tool changes. How does the four‑flute design affect surface finish? The four‑flute geometry provides smoother cutting action and improved surface finish compared with fewer‑flute tools, particularly in finishing passes on steel and cast parts. Is the tool suitable for hardened steels? The tool data specifies suitability up to certain strength limits (approx. 800 N/mm² uncoated, 1200 N/mm² with coating); it is not explicitly indicated for high‑hardness steels beyond those ranges. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

The combination of a TiCN-coated surface and a HSS‑Co5 substrate delivers extended tool life and consistent cutting performance, while the Weldon shank ensures secure clamping for stable machining. Order the cutter directly via Metav Werkzeuge or consult the Metav specialists for application advice. TECWERK End Mill DIN 844 Type HR, 6 mm – HSS‑Co5, TiCN‑coated The TECWERK End Mill DIN 844 Type HR D.6mm is a long, four‑flute HSS‑Co milling cutter designed for precision finishing and general milling of steel and cast iron in workshop and production environments HSS‑Co5 body with TiCN coating Four‑flute geometry for smooth chip removal Weldon shank with drive flat Suited to steel up to ~1200 N/mm² Longer tool life and steady performance under load The TiCN finish on the HSS‑Co5 substrate increases surface hardness and reduces friction, which results in longer tool life and fewer tool changes on the shop floor. In practice, the coating lowers build‑up and improves heat resistance during elevated cutting speeds; this translates into higher uptime and a more predictable machining cycle. The cutter’s solid composition and DIN‑compliant design support repeatable results in short to medium production runs. Secure clamping and runout stability for precision work A Weldon shank with drive flat provides positive drive and improved concentricity in standard tool holders, reducing slippage during interrupted cuts. The cylindrical shank with drive flat and the cutter’s adherence to DIN 844 ensure compatibility with common toolholders and predictable runout behaviour. For tools with a 6 mm shank and the given geometry, this mechanical reliability contributes directly to dimensional consistency and surface finish quality. Geometry optimised for steel and cast iron machining The long profile and four‑flute configuration produce a favourable balance between cutting edge engagement and chip evacuation. The tool is centre‑cutting with a 45° protective chamfer, allowing plunge starts and improved entry behaviour. A relief‑ground fine profile minimises rubbing and reduces axial cutting forces, which benefits the machining of harder materials. Suitability ratings indicate very good performance on steel and cast iron, with conditional use on non‑ferrous metals, stainless alloys and special alloys where appropriate feeds and speeds are applied. Practical benefits for production and workshop use Using this cutter in a consistent, documented tool setup reduces process variability and supports throughput targets on both single‑part and small‑batch production. The combination of HSS‑Co5 toughness and TiCN low friction improves tool life in interrupted or semi‑finishing operations, while the Weldon shank secures the tool in automatic tool changes. For buyers seeking a balance between cost, robustness and machining quality, this specification supports stable machining routines without demanding specialised holders or unusually complex parameters For procurement, technical queries or tailored application recommendations for TECWERK cutters, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 — Metav’s specialists will advise on feeds, speeds and inventory supply. Technical data Article number: 2000866546NW Product: End mill, DIN 844, Type HR, Weldon shank Material: HSS‑Co5 Coating: TiCN Core measurements Diameter: 6 mm Shank diameter: 6 mm Overall length: 68 mm Effective length: 30 mm Cutting length: 4 mm Number of flutes: 4 Materials & features Long design, 45° protective chamfer Centre‑cutting geometry Relief‑ground fine profile Cylindrical shank with drive flat (Weldon) Right‑hand cutting Very good suitability for steel Very good suitability for cast iron Conditional suitability for non‑ferrous metals, stainless and special alloys FAQ What materials is this cutter best suited to? This TECWERK end mill performs very well on steel and cast iron; it is conditionally suitable for non‑ferrous metals, stainless and special alloys when appropriate cutting parameters are applied. Is the cutter suitable for plunge milling? Yes, the centre‑cutting geometry and the 45° chamfer allow plunge starts; the tool’s profile supports controlled entry during axial engagement. Which shank system is required for secure clamping? The cutter features a Weldon shank with a drive flat; compatible Weldon‑type holders or collet systems with the matching flat ensure secure clamping and reduced slippage. How does the TiCN coating improve performance? The TiCN coating lowers friction and increases surface hardness, which reduces build‑up and thermal wear; this leads to prolonged tool life and more consistent cutting conditions. Does the cutter comply with industrial standards? The tool is manufactured to DIN 844 Type HR specifications, ensuring dimensional and performance consistency for industrial applications. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from the combination of universal material compatibility, a heat-resistant TiAlN coating and a vibration-reducing geometry that keeps production steady; order the TECWERK solid carbide end mill directly via Metav Werkzeuge or ask our consultants for application support. Solid Carbide End Mill DIN 6527 L, Ø6 mm — TiAlN, 35–38° helix (TECWERK) The Solid Carbide End Mill DIN 6527 L, Ø6 mm is a long, multi-flute cutter designed for efficient roughing and finishing across a wide range of engineering materials in industrial milling applications. Solid carbide construction, TiAlN coating 35–38° helix angle for stable chip evacuation Six flutes for high material removal rates Long shank with neck relief for low vibration High productivity with longer tool life The TECWERK cutter combines solid carbide substrate with a TiAlN surface treatment to increase heat resistance and protect against built-up edge during continuous milling cycles. The 35–38° helix reduces cutting forces and improves chip flow, while the six-cutting-edge configuration enables higher feed rates without sacrificing stability. With a cutting length of 6 mm and an effective length of 20 mm, the geometry supports both rapid material removal and controlled finishing passes, resulting in extended service intervals and fewer tool changes for a more efficient production flow. One-tool versatility across common and demanding materials Thanks to the latest geometry and coating, this long end mill is highly suitable for steel, stainless (Cr–Ni) steels, cast and grey cast irons, non-ferrous metals and aluminium alloys with silicon content, as well as abrasive or special alloys encountered in modern workshops. The universal fine-grain carbide substrate paired with TiAlN makes the tool appropriate for both roughing and finishing, enabling consolidated tooling strategies where fewer cutters are needed to cover multiple operations — a clear advantage for mixed-production environments and small series manufacturing. Stable machining and superior surface quality Designed with unequal pitch and a neck relief (neck clearance), the cutter minimises chatter and vibration even in long-reach applications, delivering consistent surface finish and dimensional accuracy. The shank meets DIN 6535 HB specifications with a shank tolerance h6, ensuring repeatable clamping precision. A protective 45° chamfer (0.12 mm) at the cutting edge improves edge strength during interrupted cuts. The right-hand cutting direction and long shank geometry together reduce the risk of harmonic excitation, supporting smoother operation and predictable tool life in industrial milling setups. Choose the TECWERK long solid carbide end mill with TiAlN coating for reliable, vibration‑reduced milling — contact Metav Werkzeuge in Emmerich for tailored application advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000866936NW UID: 2000866936NW Norm: DIN 6527 Manufacturer: TECWERK Product type: Solid carbide end mill Coating: TiAlN Material: VHM Dimensions and data Diameter: 6 mm Shank diameter: 6 mm Overall length: 57 mm Cutting length: 6 mm Effective length: 20 mm Free relief length: 5.8 mm Flutes: 6 Helix angle: 35–38° Cutting direction: right-hand Packing unit: 1 Design and special features DIN 6527 L, Type N, long version Multi-flute geometry, unequal pitch Neck relief for low-vibration machining 45° protective chamfer, 0.12 mm Cylindrical shank to DIN 6535 HB, tolerance h6 Suitable for roughing and finishing Universal fine-grain solid carbide substrate Especially suited for steel, INOX, castings, NE-metals, aluminium with Si and abrasive materials FAQ What materials is this cutter suitable for? The TECWERK solid carbide end mill (SKU 2000866936NW) is highly suitable for steel, stainless (Cr–Ni) steels, cast iron, grey cast iron, non‑ferrous metals and aluminium alloys with silicon, plus abrasive and special alloys. Can the tool be used for both roughing and finishing? Yes. The geometry and TiAlN coating make the cutter appropriate for combined roughing and finishing operations while maintaining edge stability and good surface quality. What features reduce vibration during long‑reach milling? Unequal pitch, neck relief and the long shank design reduce harmonic excitation; the tool’s neck relief and newly developed geometry enable quieter, more stable machining with improved surface results. What are the key dimensions for clamping and reach? The cutter has a diameter and shank of 6 mm, an overall length of 57 mm, a cutting length of 6 mm and an effective length of 20 mm, with shank tolerance h6 for precise clamping. Which standard and coating does the tool comply with? The cutter conforms to DIN 6527 L, features a TiAlN coating and is manufactured from VHM (solid carbide) to ensure thermal resistance and wear protection. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of a high-performance, short solid carbide solution with TiAlN surface treatment and a compact 6 mm diameter for stable, high-speed milling cycles; order directly via Metav Werkzeuge or consult the team for application-specific advice. End Mill DIN 6527K Type N/HPC – 6 mm, solid carbide with TiAlN (TECWERK) An End Mill DIN 6527K Type N/HPC designed for high-performance roughing and finishing across steels, cast irons and non-ferrous alloys. Solid carbide, TiAlN coating 6 mm diameter, 16 mm effective length Four flutes with centre cutting for plunging Short design with neck relief for low vibration High-speed performance for shorter cycle times The cutter combines a solid carbide body with a hard TiAlN surface layer to raise heat resistance and wear life during demanding HPC work. The four-flute geometry and the centre-cutting capability enable axial plunging and efficient chip evacuation, which reduces tool-change frequency and shortens overall machining cycles. As a result, machining programmes run more economically while maintaining consistent material removal rates and surface integrity. Broad material suitability for flexible job scheduling Designed with a universal geometry, the tool performs well in a wide range of materials: steel, cast iron, stainless steel, aluminium with silicon, and various non-ferrous and special alloys. The cutter’s configuration supports both roughing and finishing passes, making it suitable for shops that prioritise flexibility. When abrasive or alloyed materials impair other tools, the combination of substrate and coating keeps tolerances stable over longer tool lives. Built for precision and vibration control A short shank and a neck relief minimise overhang-induced deflection, while an unequal pitch reduces harmonic chatter in interrupted or deep cuts. The shank conforms to DIN 6535 HB with a tight h6 tolerance for reliable clamping and concentricity. The tool also features a 45° chamfer and a protective micro‑bevel to safeguard the cutting edge during entry, supporting repeatable part quality in serial production. Compact dimensions that simplify fixture and tool planning With a 6 mm nominal diameter, a cutting length of 4 mm and an effective length of 16 mm, the cutter fits compact tool assemblies and shorter holders for enhanced rigidity. The short design and right-hand cutting direction suit stable setups and allow easy integration into existing tool cycles without major programme changes. This balance of size and capability makes the cutter a practical choice for tooling inventories aiming to reduce the number of specialised tools required. For precise application advice or stock enquiries about the TECWERK TiAlN-coated solid carbide end mill, contact Metav Werkzeuge directly at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific materials and processes Technical data SKU: 2000866484NW Standard: DIN 6527 Product type: End mill Manufacturer: TECWERK Facts Diameter: 6 mm Cutting length: 4 mm Effective length: 16 mm Overall length: 54 mm Shank diameter: 6 mm Number of flutes: 4 Free relief (neck): 5.8 mm Chamfer (protection): 0.12 mm Special features Solid carbide (fine grain) TiAlN coating DIN 6527 K · Type N / HPC Centre cutting (axial plunge) Short design for reduced overhang 45° protective chamfer Cylindrical shank to DIN 6535 HB, tolerance h6 Unequal pitch for vibration reduction Right‑hand cutting Neck relief for vibration‑reduced machining Suited for roughing and finishing Suitable for steel, cast iron, stainless steel, non‑ferrous alloys and abrasive materials FAQ Is this cutter suitable for plunge milling? Yes. The TECWERK end mill is centre cutting, so axial plunging is possible; the four‑flute geometry supports chip evacuation during plunge operations. Which materials does the tool perform best in? The tool is optimised for a broad range: steel, cast iron, stainless steel and non‑ferrous alloys, including aluminium with silicon content, offering very good suitability across these materials. What advantage does the TiAlN coating provide? The TiAlN layer increases thermal stability and wear resistance, extending tool life in high‑speed and high‑temperature conditions compared with uncoated carbide. How does the short shank affect performance? The short design reduces overhang, improves rigidity and minimises vibration, which enhances dimensional accuracy and surface finish in both roughing and finishing passes. Can this cutter be clamped in standard DIN toolholders? Yes. The shank is a cylindrical type compliant with DIN 6535 HB and a h6 tolerance, ensuring secure and concentric clamping in standard holders. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Take advantage of a combination of solid carbide construction, TiAlN surface protection and a compact, vibration‑resistant design for reliable high‑performance milling. Order the TECWERK cutter directly via Metav Werkzeuge or contact the consultants for process‑matching advice. End mill WN Type N, 6 mm — VHM, TiAlN, 35° helix (TECWERK) The End mill WN Type N, 6 mm, solid carbide (VHM), TiAlN‑coated is a short, high‑efficiency cutter designed for roughing, finishing and groove machining across a broad range of metals. Solid carbide VHM construction for high stiffness TiAlN coating for heat resistance and longevity 35° helix for high cutting efficiency Extra‑short design for vibration‑free machining Four flutes for improved surface finish Greater material removal and consistent surface quality The combination of VHM (solid carbide) substrate and TiAlN coating delivers a step change in thermal stability and wear resistance, enabling higher cutting speeds and longer tool life. The pronounced 35° helix promotes efficient chip evacuation while the four flutes balance material removal with a fine machining result. Thanks to the proven HPC geometry with unequal pitch, the cutter reduces harmonic excitation and provides a consistently good surface finish when machining steel up to 45 HRC as well as cast iron, copper, brass and aluminium. This makes the tool a pragmatic choice where process reliability and productivity are key. Compact form for stable, vibration‑free cutting and accurate grooves The extra‑short design and short, stable execution prioritise rigidity at the cutting zone. A shorter overhang reduces deflection, so the tool excels in groove work, roughing and finishing where stability matters. The end mill features a centre‑cut capability for plunge operations and a cylindrical shank to DIN 6535 HB, ensuring secure clamping and repeatable run‑out in standard toolholders. The geometry also incorporates a soft cutting angle (10°) to moderate cutting forces, which helps preserve machine and workpiece integrity during robust machining cycles. Longer service life and predictable process behaviour Small but decisive details improve operational robustness: a protective chamfer of 0.2 mm at the cutting edge reduces chipping during interrupted cuts, and the right‑hand cutting direction matches standard machining setups. The fine‑grain carbide substrate paired with the TiAlN layer resists built‑up edge and thermal wear, lowering the frequency of tool changes and supporting steady production throughput. Designed for high‑performance cutting (HPC), the tool is suited to applications where reproducible results and reduced downtime translate into measurable process gains. Contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss how the TECWERK end mill suits specific machining tasks and to request tailored advice from the precision team Technical data Article number: 2000866414NW Manufacturer: TECWERK Product type: End mill (Schaftfräser) Norm: DIN 6527 Core data Diameter: 6 mm Overall length: 40 mm Cutting length: 4 mm Shank diameter: 6 mm Number of flutes: 4 Helix angle: 35° Protective chamfer: 0.2 mm Cutting direction: right‑hand Special features Material: solid carbide (VHM) Coating: TiAlN Geometry: HPC with unequal pitch Design: extra‑short, short and stable execution Centre‑cut for plunge machining Shank: cylindrical shank to DIN 6535 HB Machining tasks: roughing, finishing, groove machining Suitable for: steel up to 45 HRC, cast iron, copper, brass, aluminium Cutting characteristic: soft cut (10°) for reduced cutting forces FAQ What materials can this end mill machine effectively? The TECWERK end mill is engineered for a wide range of materials, being very well suited to steel up to 45 HRC, and also suitable for cast iron, copper, brass and aluminium; performance in stainless steel and non‑ferrous metals is indicated as conditional. Is the cutter suitable for plunge or ramping operations? Yes. The tool has a centre‑cut capability that allows plunge and ramping operations as part of its intended use. How does the TiAlN coating benefit production runs? The TiAlN coating increases thermal resistance and reduces wear, which supports higher cutting speeds and longer tool life under continuous production conditions. What clamping standard does the shank follow? The cutter is supplied with a cylindrical shank conforming to DIN 6535 HB, enabling secure clamping in standard toolholders. Does the geometry reduce vibration during heavy cuts? The tool uses HPC geometry with unequal pitch and an extra‑short form to lower harmonic excitation and provide vibration‑reduced machining for improved surface finish. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Reliable machining performance from a solid carbide body and TiAlN coating, combined with a long working length and vibration‑reducing geometry for consistent roughing and finishing results. Order the end mill directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. TECWERK long solid carbide end mill, 6 mm — TiAlN, 4‑flute, centre‑cut The TECWERK end mill for high‑performance roughing and finishing in steels, cast irons and non‑ferrous alloys, designed for vibration‑reduced pocketing and plunge operations. *Solid carbide body with TiAlN coating *Long effective length for deep pocketing *Unequal pitch and neck relief reduces vibration *Centre‑cutting, four‑flute design for versatility High-temperature resistance for longer tool life The combination of solid carbide construction and a TiAlN coating significantly raises the tool’s resistance to heat during high‑speed or interrupted cutting. This chemical vapour deposited coating forms a stable, hard surface that reduces adhesion and wear at elevated temperatures, which in turn extends service intervals and lowers tool consumption. For workshops aiming to keep cycle times stable under demanding conditions, this treatment delivers predictable performance and reduced tool change frequency. Stable cutting with minimised chatter and reliable surface finish A four‑flute configuration with unequal pitch and a dedicated neck relief reduces harmonic vibrations and improves stability when machining interrupted surfaces or long overhangs. The geometry includes a 45° chamfer and centre‑cutting capability, enabling plunge cuts and reliable entry into the component. These features translate into a more consistent surface finish and fewer rejects in series production, particularly when processing steels, stainless steels, cast iron and many non‑ferrous alloys. Long reach and universal application for roughing and finishing With a long overall length and an effective length of 20 mm, the tool is built for deep pocketing and cavities where reach is critical. The cylindrical shank to DIN 6535 HB with a h6 tolerance ensures secure clamping and concentricity in standard holders. Thanks to its optimised geometry and coating, the cutter is suited to HPC strategies as well as finish passes in materials ranging from aluminium alloys with silicon to abrasive, high‑strength steels and special alloys, providing a versatile solution across jobbing and production environments. Contact Metav Werkzeuge for tailored cutting data or to order the TECWERK end mill (SKU 2000866524NW) — shipped from Emmerich with expert support Technical data Article number / SKU: 2000866524NW Standard: DIN 6527 Product type: End mill (long) Facts Diameter: 6 mm Overall length: 57 mm Effective cutting length: 20 mm Cutting length (small flute): 4 mm Flutes: 4 Shank diameter: 6 mm Shank tolerance: h6 Special features Material: solid carbide (VHM) Coating: TiAlN Cutting direction: right‑hand cut Centre cutting (plunge capable) Unequal pitch for reduced vibration Neck relief for low‑vibration overhangs 45° chamfer / chamfer size 0.12 mm Cylindrical shank to DIN 6535 HB Suitable for steel, stainless steel (INOX), cast iron, non‑ferrous metals, aluminium with silicon, special alloys and abrasive materials Application: High‑performance cutting (HPC), roughing and finishing Packaging unit: 1 FAQ Is this tool suitable for plunge cutting? Yes. The TECWERK long solid carbide end mill features a centre‑cutting geometry that allows plunge operations as well as conventional milling. Which materials can be machined with this cutter? The tool is designed for a wide range of materials: steels (including high‑alloy), stainless steel (INOX), cast iron, non‑ferrous metals and aluminium alloys with silicon, as well as abrasive and special alloys. How does the TiAlN coating help in production? The TiAlN coating increases thermal resistance and reduces adhesion, which improves tool life under high temperatures and supports stable performance in continuous production runs. What features reduce chatter when working with long overhangs? Unequal pitch, neck relief and the four‑flute geometry work together to suppress vibrations and maintain a consistent surface finish during extended reach machining. What is the exact product identification for ordering? Order the TECWERK long solid carbide end mill (6 mm, TiAlN, 4‑flute) under SKU 2000866524NW for direct supply from Metav Werkzeuge. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

With a TiAlN coating and solid carbide construction, this cutter delivers durable edge stability and consistent finish even in demanding operations; the extra‑long design and 35–38° helix enable efficient chip evacuation and extended reach for deep cavities. Make use of these qualities for reliable roughing and finishing cycles — order the TECWERK Type N solid carbide end mill directly via Metav Werkzeuge or ask our consultants if needed. TECWERK Type N solid carbide end mill, D 6 mm — TiAlN, 6 flutes, extra‑long The Type N solid carbide end mill is an extra‑long, multi‑flute cutter engineered for universal milling tasks in steel, cast materials and non‑ferrous alloys. Solid carbide, TiAlN coating for long tool life 6 flutes with unequal pitch for smooth chips Extra‑long reach for deep cavity machining 35–38° helix for rapid chip evacuation High productivity for roughing and finishing operations This cutter is designed to combine material removal rate and surface quality in a single tool. With a solid carbide body and a TiAlN surface finish, the geometry promotes stable cutting at elevated temperatures and reduces flank wear, which extends usable life and minimises tool changes. The multi‑flute configuration and unequal pitch reduce chatter and enable a steady feed, so machining cycles run more efficiently and deliver repeatable results for both roughing and finishing tasks. Versatile material compatibility with reliable results The tool’s geometry and coating make it suitable for a broad range of materials, including carbon and alloyed steels, cast and stainless steels, as well as many non‑ferrous metals and abrasive alloys. The right‑hand cut and high 35–38° helix angle help evacuate chips quickly and lower cutting forces, which is particularly beneficial when working in interrupted cuts or thin walls. This versatility reduces the need for multiple special‑purpose cutters and simplifies tool selection for mixed‑material production. Process stability and toolholder friendliness An extra‑long overall length combined with a precisely ground shank and h6 tolerance provides secure clamping and better concentricity in the toolholder. The tool features a protective chamfer and a neck relief to limit stress at the transition area, supporting vibration‑reduced machining even in deeper reaches. These characteristics contribute to greater process stability, improved surface finish and fewer rejected parts over a production run. Clear advantages for workshop efficiency Choosing a tool that supports both heavy material removal and a fine finish reduces cycle count and tool inventory. The combination of an advanced coating and a robust carbide substrate reduces thermal softening at the cutting edge, while the six‑flute layout promotes a finer surface without sacrificing throughput. For job shops and production floors aiming to streamline operations, this cutter helps shorten set‑up times and increase effective spindle utilisation. For high‑reach milling tasks, request the TECWERK Type N solid carbide end mill via Metav Werkzeuge — our Emmerich‑based specialists can advise on toolholder compatibility and suggest optimised machining parameters; contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored support. Technical data SKU: 2000866329NW Norm: DIN 6527 Label: Schaftfräser TypN D.6mm Einsatz-L.25mm VHM TiAlN 35-38Grad HB Z.6 ext.lang TW Manufacturer: TECWERK Facts Diameter: 6 mm Overall length: 62 mm Effective (cutting) length: 25 mm Flutes: 6 Helix angle: 35–38° Shank diameter: 6 mm Shank tolerance: h6 Special features Material: solid carbide (VHM) Coating: TiAlN Type: Type N, multi‑cutting edge, extra‑long Cutting direction: right‑hand cut Unequal pitch for vibration damping Neck relief and chamfer for stress reduction Suitable for roughing and finishing Designed for low‑vibration machining Protective chamfer: 0.12 mm FAQ What materials is this cutter suitable for? The TECWERK Type N solid carbide end mill is suitable for steels, cast materials, stainless steels and a wide range of non‑ferrous alloys, as stated in the product specification. How many flutes does the tool have and why does that matter? This cutter has six flutes; the six‑flute geometry increases material removal without compromising the finish and, together with unequal pitch, reduces vibration during machining. What is the effective cutting length of the tool? The effective cutting length is 25 mm, which gives the extra‑long design the reach needed for deeper pocketing and cavity work. Is the shank compatible with standard toolholders? The shank diameter is 6 mm with an h6 tolerance, allowing secure clamping in standard collets and holders that accommodate 6 mm shanks. What benefits does the TiAlN coating provide? The TiAlN coating increases heat resistance and reduces adhesive wear, improving edge life and process reliability under elevated cutting temperatures. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from the combination of HSS‑Co5 construction and a Weldon drive flat for vibration‑resistant, precise short‑reach milling; order this DIN 844 short end mill directly via Metav Werkzeuge or consult our specialists for application guidance. End mill DIN 844 Type NR Ø6 mm, HSS‑Co5, Weldon shank – TECWERK The End mill DIN 844 Type NR Ø6 mm HSS‑Co5 is a short, three‑flute, centre‑cutting cutter designed for accurate milling of steels, cast parts and selected non‑ferrous materials in compact setups. HSS‑Co5 high‑alloy cutting material suitable for steels DIN 844 short Type NR geometry for rigid setups Weldon shank with drive flat for secure clamping Centre‑cutting three‑flute design for axial entry High‑performance material for demanding shop work The HSS‑Co5 composition delivers a balance of toughness and red‑hardness, making this cutter well suited to interrupted cuts and harder operating conditions. With an uncoated rating for components up to ≈800 N/mm², the tool supports frequent use in maintenance and small‑batch production where tool life and predictability matter. The short geometry reduces overhang, increasing rigidity and helping to maintain dimensional accuracy on shoulders and small step features. Consistent chip control and edge protection for improved surface finish A three‑flute, centre‑cutting geometry with a relieved flute profile and a 45° protective chamfer promotes controlled chip evacuation and stable cutting forces. The tool’s effective length 19 mm and a cutting length of 3 mm concentrate cutting action where it is needed, reducing chatter and helping to achieve repeatable surface quality. The moderate relief (freischliff 5.5 mm) supports cleaner entry and exit, which is particularly valuable when milling castings or interrupted surfaces. Secure clamping and repeatable set‑ups reduce downtime The Weldon shank with drive flat provides positive torque transmission and simple tool indexing in standard holders, speeding changeovers and reducing the risk of slippage during heavy engagement. Compliance with DIN 844 ensures familiar geometry for toolroom planners and purchasing departments, while the short multi‑flute format improves rigidity for compact fixturing and tight‑tolerance operations. Practical suitability and workshop recommendations Right‑hand cutting and the short NR type make this cutter a dependable choice for profile milling, small slotting and shoulder operations in workshops and maintenance bays. Materials suitability indicates very good performance on steel and cast iron, with conditional use on non‑ferrous metals; this matches many common daily tasks in tooling, repair and small‑series production. For application advice or to confirm fitment in specific tool holders, technical support is available from Metav Werkzeuge. Contact Metav Werkzeuge today for tailored advice or to order the TECWERK end mill directly from our Emmerich warehouse Technical data Article number: 2000866463NW Manufacturer: TECWERK Standard: DIN 844 Product type: End mill (short, Type NR) Facts Diameter: 6 mm Overall length: 57 mm Effective length: 19 mm Cutting length: 3 mm Shank diameter: 6 mm Number of flutes: 3 Relief grind: 5.5 mm Cutting direction: Right‑hand Special features Material: HSS‑Co (HSS‑Co5) Centre cutting Weldon shank with drive flat 45° protective chamfer Relieved flute profile / honed relief Short multi‑flute design (Type NR) Very good suitability for steel and cast iron Packaging unit: 1 FAQ Is this cutter suitable for shoulder milling in steel? The TECWERK end mill (DIN 844 Type NR, Ø6 mm) is designed for rigid, short‑reach shoulder milling and is rated very good for steel machining up to approximately 800 N/mm² with an uncoated tool. Can the tool be used for aluminium and other non‑ferrous metals? The cutter is conditionally suitable for non‑ferrous metals; the three‑flute geometry offers good chip control, but machining parameters should be adapted to the specific alloy and rigidity of the set‑up. What clamping option is recommended for this shank? Use a Weldon‑compatible holder or collet block that accepts a drive flat; the Weldon shank provides secure torque transmission and repeatable seating for the cutter. Does the tool allow plunge cutting? As a centre‑cutting three‑flute end mill, it permits axial entry and plunge cutting; attention to machine rigidity and feed rates is advised to maintain tool life. What standard does the geometry follow and why does that matter? The geometry conforms to DIN 844, which standardises short Type NR end mills for predictable performance, easy replacement and compatibility with common tool‑holding practice. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

The combination of HSS‑Co PM construction and ALCRONA coating delivers extended tool life and consistent performance, while the Weldon shank ensures secure clamping and torque transmission; order the TECWERK short 6 mm HSS‑Co PM end mill directly via Metav Werkzeuge or ask our consultants if needed. TECWERK short 6 mm HSS‑Co PM end mill DIN 844 – ALCRONA, 4 flutes, Weldon shank The TECWERK short 6 mm HSS‑Co PM end mill is a DIN 844 Type N, centre‑cutting, right‑hand 4‑flute cutter for efficient milling of steels, stainless steel and cast iron in general workshop and light industrial applications. HSS‑Co PM with ALCRONA coating DIN 844 Type N, 4‑flute short design Weldon shank with drive flat Centre‑cutting, right‑hand cutting Precision and endurance for consistent throughput Constructed from HSS‑Co PM, this short end mill combines the toughness of cobalt‑alloyed high‑speed steel with powder‑metallurgical microstructure for improved wear resistance. The ALCRONA coating reduces friction and increases thermal stability, which together extend tool life under interrupted cuts and higher feed rates. For operations where repeatable accuracy and reduced tool change frequency matter, this tool translates material properties into measurable production gains and lower total cycle times. Material suitability and reliable chip control Designed to machine materials up to roughly 1000 N/mm², the cutter is very well suited for steel, stainless steel and cast iron, while non‑ferrous metals and special alloys are conditionally suitable. The 4‑flute geometry balances cutting edge engagement and chip space, allowing efficient material removal on short axial depths. Centre‑cutting flutes permit plunge milling, and the right‑hand cutting direction matches conventional spindle setups. These characteristics reduce secondary operations and support a lean machining process. Geometry engineered for stability and vibration reduction The short overall length and the Weldon shank with drive flat provide secure clamping and minimise overhang‑related deflection. Unequally divided flutes offer vibration reduction, improving surface finish and tool life where chatter would otherwise be a problem. An optimised flute root increases effective stiffness, converting tool rigidity into smaller tolerances on finished components and fewer scrapped parts, which supports both productivity and quality control objectives. Practical handling and workshop integration With a 6 mm diameter and an effective length tailored for short‑reach profiling, the cutter is straightforward to set up on common milling machines and compact machining centres. The DIN 844 Type N standard ensures compatibility with existing tool libraries and holders, simplifying inventory and procurement. For buyers seeking a dependable, compact cutter that fits standard fixtures and reduces setup complexity, this tool delivers a pragmatic balance of performance and ease of use. Contact Metav Werkzeuge for personalised machining advice and delivery options on the TECWERK short 6 mm HSS‑Co PM end mill (SKU 2000866031NW); eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical data Article number: 2000866031NW Standard: DIN 844 Type designation: Type N Material: HSS‑Co PM Coating: ALCRONA Facts Diameter: 6 mm Overall length: 57 mm Cutting length: 4 mm Effective length: 19 mm Free margin: 5.5 mm Cutting edges: 4 Shank diameter: 6 mm Cutting direction: right‑hand Packing unit: 1 Special features Weldon shank with drive flat Centre‑cutting geometry Short design for reduced overhang Unequally divided flutes for vibration reduction Improved rigidity by tapered flute root Suited for steel, stainless steel, cast iron (very good) Conditionally suitable for non‑ferrous metals and special alloys FAQ What materials can this cutter machine effectively? The TECWERK short 6 mm HSS‑Co PM end mill is very well suited for steel, stainless steel and cast iron; non‑ferrous metals and special alloys are conditionally suitable. Does the tool support plunge milling? Yes, the centre‑cutting geometry of this Type N end mill allows plunge operations as well as conventional side milling. What are the benefits of the ALCRONA coating? The ALCRONA coating on the HSS‑Co PM substrate reduces friction and increases thermal resistance, which extends tool life during intermittent cuts and higher feeds. How does the Weldon shank improve machining? The Weldon shank with drive flat ensures secure clamping and reliable torque transmission, reducing the risk of slippage and improving repeatability on short‑reach operations. Is this cutter compatible with standard toolholders? Compliance with DIN 844 and the 6 mm shank diameter make the cutter compatible with common collet chucks and holders used in general workshop and light industrial setups. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Combining the heat resistance of HSS‑Co5 with a secure Weldon shank, this short multi‑flute end mill gives consistent chip evacuation and stable performance in steel and cast iron; order the cutter directly via Metav Werkzeuge or consult our specialists for machining advice. End mill DIN 844 Type NR, 8 mm HSS‑Co5 – Weldon shank (TECWERK) A End mill DIN 844 Type NR for short, high‑precision milling in medium‑strength steels and cast iron, featuring a 25 mm effective cutting length and a robust Weldon shank. HSS‑Co5 high‑speed steel construction DIN 844 Type NR, short multi‑flute design 25 mm effective cutting length, 45° chamfer Weldon shank with drive flat for secure clamping Stable performance in medium‑strength materials The HSS‑Co5 composition raises red hardness and toughness compared with conventional high‑speed steels, resulting in more reliable edge retention under heat. With an 8 mm diameter and 25 mm effective cutting length, this cutter is designed for efficient pocketing and face milling operations in materials up to approximately 800 N/mm² in its uncoated form. The DIN 844 geometry and central cutting capability allow plunge operations and precise entry into the workpiece, reducing the need for pre‑drilled starts and simplifying setup for series production. Secure clamping and vibration control for consistent results A Weldon shank with a drive flat ensures positive engagement in the toolholder and reduces the risk of slippage during heavy intermittent cuts. The short, multi‑flute layout (three cutting edges) and the 45° protection chamfer together improve chip evacuation and lower radial cutting forces, which helps to avoid chatter on less rigid setups. The relieved flute profile provides a controlled cutting edge, delivering dimensional stability and repeatable surface quality across runs. Predictable tool life and process economy Supplied uncoated, this cutter offers a reliable baseline for many workshop applications; the cobalt alloy increases resistance to work‑hardening and thermal softening, extending useful life compared with plain HSS. Tool reconditioning is straightforward thanks to the classic geometry and accessible flute design, which keeps down total cost of ownership for medium‑volume production. Suitability assessments: steel – very well suited; cast iron – very well suited; non‑ferrous metals – conditionally suited, depending on feed and speed adjustments. Contact Metav Werkzeuge for a tailored cutting tool recommendation and to secure this TECWERK HSS‑Co5 end mill for reliable supply from Emmerich. Technical Data SKU: 2000866465NW Article designation: End mill DIN 844 Type NR, HSS‑Co5, Weldon shank Standard: DIN 844 Manufacturer: TECWERK Facts Diameter: 8 mm Overall length: 69 mm Effective cutting length: 25 mm Flutes: 3 Shank diameter: 10 mm Special features Material: HSS‑Co (HSS‑Co5) Weldon shank with drive flat Right‑hand cutting Central cutting geometry (plunge capable) 45° protection chamfer Relieved flute profile Supplied uncoated Very well suited for steel and cast iron; conditionally for non‑ferrous metals FAQ What materials is this end mill suitable for? The TECWERK end mill (DIN 844 Type NR, SKU 2000866465NW) is very well suited for steel and cast iron; non‑ferrous metals are conditionally suitable with adapted feeds and speeds. Can this cutter be used for plunge milling? Yes, the central cutting geometry of the tool permits plunge cutting, allowing direct entry into the workpiece without pre‑drilling for many applications. Does the tool come coated? This particular item is supplied uncoated; the HSS‑Co5 substrate still offers improved heat resistance, and coated variants can be considered where higher surface speeds are required. What holder is recommended for secure clamping? A toolholder that accommodates a Weldon shank with a matching drive flat is recommended to ensure secure clamping and to prevent rotation under load. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of durable HSS‑Co8 cutting geometry, a rigid Weldon shank and the short, DIN 844 Type N design for stable, high‑productivity milling. Order the tool directly via Metav Werkzeuge or consult the team for application advice. Schaftfräser DIN 844 Type N, 8 mm, HSS‑Co8 — short 4‑flute end mill by TECWERK The Schaftfräser DIN 844 Type N, 8 mm HSS‑Co8 is a short, centre‑cut end mill designed for rigid milling and plunge work in workshop and industrial settings. HSS‑Co8 for improved heat resistance DIN 844 Type N short 4‑flute design Weldon shank with drive flat for secure clamp Centre‑cut for plunge and slotting operations Stable cutting performance for demanding steel machining The short 4‑flute geometry, manufactured from HSS‑Co8, provides a reliable balance between wear resistance and toughness for interrupted cuts. With an 8 mm cutter diameter and 4 mm cutting length, the tool concentrates stiffness close to the cutting zone, reducing deflection and chatter during heavy engagement. The centre‑cut feature permits controlled plunging and slotting without pre‑drilling, while the 4‑flute layout optimises surface finish on side walls. Performance guidance indicates suitability up to 800 N/mm² in uncoated condition and, where a suitable coating is applied, material strength limits can be extended toward 1000 N/mm² — crucial information when setting feeds and speeds. Secure clamping and dimensional control for repeatable setups Clamping reliability is provided by the Weldon shank with drive flat on a 10 mm shank diameter, paired with a compact 69 mm overall length and 25 mm effective length. This configuration minimises overhang and improves run‑out stability in collets or chucks, translating into consistent part accuracy and longer tool life. The short design also simplifies fixture planning in small machining centres or compact rigs. The tool’s ground relief (approx. 7.5 mm) contributes to predictable chip flow and reduced rubbing at the flank, which helps maintain dimensional control across serial runs. Broad workshop applicability with clear material recommendations Designed to the DIN 844 Type N specification, this end mill is primarily engineered for conventional steels and cast iron where it is very well suited, while performance on stainless and non‑ferrous alloys is conditional and depends on cutting data and part geometry. The cutter is right‑hand cutting, making it compatible with standard milling strategies. For marginal materials or complex alloys, pairing the substrate with an appropriate coating and adapted cutting parameters can extend tool capability. For technical clarifications or to discuss specific workpiece materials and cycle optimisation, Metav’s technical advisers can provide tailored recommendations and machining data. Contact Metav Werkzeuge for availability and personalised technical advice from their Emmerich team — phone +49 2822 7131930 or email info@metav-werkzeuge.com — to ensure the TECWERK Schaftfräser is matched to the intended application. Technical Data Article number: 2000866330NW Standard: DIN 844 SKU: 2000866330NW Facts Diameter: 8 mm Overall length: 69 mm Cutting length: 4 mm Effective length: 25 mm Shank diameter: 10 mm Flutes: 4 Relief / free grind: 7.5 mm Cutting direction: right‑hand cutting Special features Material: HSS‑Co (cobalt high‑speed steel) Type: DIN 844 Type N, short, centre‑cut Shank: cylindrical with Weldon drive flat Application: suitable for steel and cast iron; conditional for non‑ferrous and stainless steels Packaging unit: 1 FAQ What applications is this TECWERK Schaftfräser best suited for? This TECWERK Schaftfräser (DIN 844 Type N, SKU 2000866330NW) is best suited for rigid milling operations in steel and cast iron, including slotting and plunge cuts where stiffness and tool life are priorities. Can the end mill be used for stainless steel and aluminium? The tool can machine stainless steel and non‑ferrous metals conditionally; optimised cutting data and, where appropriate, a compatible coating are recommended to improve performance on these materials. What does HSS‑Co8 mean for tool behaviour? HSS‑Co8 indicates a cobalt‑alloyed high‑speed steel that offers improved hot hardness and toughness compared with standard HSS, benefiting the TECWERK end mill during higher temperatures and intermittent cutting. Is the Weldon shank compatible with standard clamping systems? Yes, the Weldon shank with drive flat provides secure clamping in common toolholders and chucks, improving resistance to rotation and enhancing repeatability in production setups. Does the cutter allow plunging without pre‑drilling? Yes, the centre‑cut design permits controlled plunging and makes the cutter suitable for short plunge operations and slotting in appropriate materials. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Taking advantage of the HSS‑Co8 composition and a 44 mm effective length yields durable performance for deep milling operations; combine the long flute design with the secure Weldon shank for reliable clamping and consistent cycles — order the TECWERK end mill through Metav Werkzeuge or request specialist advice from our consultants. TECWERK end mill DIN 844 Type N — 8 mm, HSS‑Co8, 4‑flute long A TECWERK end mill DIN 844 Type N engineered for deep slotting, plunge cuts and general milling of castings and steels in workshop and production environments. HSS‑Co8 for high wear resistance Long effective length 44 mm for deep cuts Weldon shank with drive flat for secure clamping Four flutes, centre‑cutting for plunge milling Reliable deep milling with extended reach The long version of this cutter combines a 44 mm effective length with a full 88 mm overall length, enabling deeper engagement without frequent tool changes. The four‑flute geometry improves chip evacuation on moderate radial engagement, while the centre‑cutting design permits controlled plunge operations. Constructed in HSS‑Co8, the tool sustains higher temperatures and resists abrasion better than plain HSS, which translates into longer tool life under intermittent heavy cuts. For shops that run mixed batches or require occasional plunge milling, this geometry reduces setup complexity and supports tighter cycle times through reduced tool handling. Clear guidance on material suitability and cutting limits Designed primarily for conventional machining tasks, the cutter shows very good suitability for steel and castings, while non‑ferrous metals and stainless steels are only conditionally suitable. Performance guidance from the tool data indicates operation up to approximately 800 N/mm² with an uncoated tool and potential service up to 1,200 N/mm² where coated options are used. These figures help planners match the cutter to job demands: for medium‑strength steels, expect consistent removal rates and good flank wear resistance; for harder alloys or high thermal loads, consider coated alternatives or adjusted cutting parameters to preserve tool life. Secure clamping and machine compatibility for stable machining The cylindrical shank is furnished with a Weldon drive flat to prevent slippage in collets or chucks, providing repeatable torque transmission in interrupted cuts. Key dimensions — 8 mm diameter, 10 mm shank, 88 mm overall length and 44 mm effective length — align with common tool holders and toolchanger capacity in machining centres and CNC mills. The cutter conforms to DIN 844, a recognised industry standard for long shank end mills, and features right‑hand cutting for conventional spindle rotation; these attributes simplify tool selection and ensure predictable integration into existing machining processes. Practical benefits for workshop efficiency and procurement For production and maintenance shops seeking dependable performance, the combination of cobalt‑alloy steel and long flute form reduces the frequency of replacements and minimises unscheduled downtime. The cutter’s robust construction supports repeatable tolerances, while the Weldon shank and standard dimensions ease tool inventory management. Procuring the cutter via Metav means access to a broad stock range and a European distribution base that emphasises reliable supply — a practical choice for operations that value continuity and a single trusted supplier for precision tools. Contact Metav Werkzeuge for availability, tailored tooling advice and to discuss the suitability of the TECWERK end mill for specific applications Technical data Article number: 2000866378NW Manufacturer: TECWERK Standard: DIN 844 Product type: End mill (long type) Facts Diameter: 8 mm Overall length: 88 mm Effective length: 44 mm Shank diameter: 10 mm Number of flutes: 4 Cutting direction: Right‑hand cutting Relief / free clearance: 7.5 mm Special features Material: HSS‑Co (cobalt high‑speed steel) Weldon shank with drive flat Centre‑cutting geometry (plunge capable) Long flute design for deep cuts Material suitability: steel — very good; castings — very good; non‑ferrous & stainless — conditionally suitable Guidance: up to ~800 N/mm² uncoated; up to ~1,200 N/mm² with coated variants FAQ What materials is this end mill best suited for? The TECWERK end mill is rated very good for steel and castings; non‑ferrous and stainless steels are conditionally suitable depending on cutting parameters. Can this cutter be used for plunge milling? Yes — the centre‑cutting geometry and four flutes permit controlled plunge operations as well as conventional side milling. Which shank size and clamping does it require? The tool has a 10 mm cylindrical shank with a Weldon drive flat for secure clamping in compatible holders. Does the cutter conform to a recognised standard? The cutter complies with DIN 844, ensuring standard dimensions and predictable fitment in tooling systems. Is the tool suitable for deep slots and extended reach applications? With a 44 mm effective length and long‑shank design, the cutter is intended for deeper slotting where a longer reach is required. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of HSS‑Co5 durability, a four‑flute geometry and a secure Weldon shank for reliable short‑run milling; order the cutter directly via Metav Werkzeuge or consult the team if required TECWERK End Mill DIN 844 Type HR Ø 8 mm (HSS‑Co5) — Weldon shank, 4‑flute TECWERK End Mill DIN 844 Type HR Ø 8 mm (HSS‑Co5) is a short, four‑flute, centre‑cutting end mill designed for efficient milling of steel and cast iron in workshop and production environments Short HSS‑Co5 geometry for tough cuts Four‑flute design for steady surface finishes Weldon shank with drive flat for secure clamping Centre‑cutting for plunge and slot milling High performance for demanding steels and castings The cutter is made from HSS‑Co5, delivering improved red hardness and wear resistance compared with standard high‑speed steel; this means consistent performance when machining ferrous materials. With suitability rated very good for steel and very good for cast iron, the tool enables stable metal removal where toughness and edge retention matter. The data indicate capability up to ≈800 N/mm² with an uncoated tool and up to ≈1200 N/mm² when a coated grade is chosen, supporting a broader process window for mixed production runs. Geometry that improves productivity and finish A four‑flute configuration combined with a centre‑cutting geometry provides an effective balance between chip evacuation and axial engagement, allowing plunge cuts and slotting without additional tool changes. The short design with a 25 mm effective length and a compact profile reduces chatter and increases rigidity, which benefits cycle time and surface quality on vertical milling operations. The relieved fine helix profile helps direct chips away from the cutting zone while preserving a clean machined surface. Secure clamping and simple handling for workshop use The cylindrical shank with a Weldon drive flat ensures firm clamping in standard holders and milling arbors, reducing the risk of slippage under intermittent loads. A shank diameter of 10 mm with an overall length of 69 mm keeps the tool compact for setups where space is limited. Right‑hand cutting and a protective 45° chamfer on the tip improve tool life in repetitive processes, making the cutter a practical choice for machining centres and manual mills alike. Practical applications and material guidance This short, four‑flute end mill is optimised for machining structural and hardened steels, and it is particularly suited to cast components where stable tool edges are required. The tool is conditionally suitable for non‑ferrous metals, so process validation is recommended when aluminium or brass workpieces form the bulk of production. For mixed operations that include tougher steels, choosing a coated variant can extend workable strength ranges and reduce regrinding frequency. Contact Metav Werkzeuge in Emmerich for tailored advice on tooling setups, variant selection and availability — the Metav team can assist with technical questions and order coordination Technical data Article number: 2000866492NW Norm: DIN 844 Manufacturer: TECWERK Product type: End mill (short, Type HR) Facts Diameter: 8 mm Shank diameter: 10 mm Effective length: 25 mm Cutting length: 4 mm Overall length: 69 mm Number of flutes: 4 Relief clearance (mm): 7.5 Special features Material: HSS‑Co5 Type HR, short design Four‑flute, centre‑cutting 45° protective chamfer Relieved fine helix profile Cylindrical shank with drive flat (Weldon) Right‑hand cutting Uncoated (coated variants recommended for higher strength ranges) Suitable: steel (very well), cast iron (very well), non‑ferrous metals (conditionally) Packaging unit: 1 FAQ What range of materials is this cutter best suited for? The TECWERK end mill (Type HR, Ø 8 mm) is rated very well for steel and cast iron, with conditional suitability for non‑ferrous metals. Can this cutter be used for plunge milling? Yes, the centre‑cutting geometry and four‑flute design permit plunge operations and slotting with the appropriate feeds and speeds. What shank system does the tool use for clamping? The tool features a Weldon shank with a drive flat, providing secure clamping in standard holders and reducing slippage risk during heavy cuts. Is there a coated version for higher strength materials? The tool is supplied uncoated; however, a coated variant is advisable when machining materials approaching ≈1200 N/mm², as coatings extend usable strength ranges. Which DIN standard does the cutter conform to? The cutter complies with DIN 844, Type HR specifications for short end mills. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from the combination of HSS‑Co construction, TiCN coating and a long 44 mm cutting reach to improve cycle times and reduce tooling changes; order the TECWERK end mill directly via Metav Werkzeuge or contact our consultants for tailored machining advice. TECWERK HSS‑Co End Mill D844 Type N, Ø8 mm, TiCN, 4‑flute, Weldon The TECWERK HSS‑Co end mill D844 Type N Ø8 mm is a long, centre‑cutting tool designed for precision milling of steel, stainless steel and cast materials in workshop and industrial environments. DIN 844 Type N, centre-cutting HSS‑Co base with TiCN coating Long 44 mm effective cutting length Weldon shank with 10 mm diameter Increased material removal with predictable performance The long 44 mm effective cutting length combined with a compact 8 mm diameter and 4‑flute geometry provides a reliable balance between rigidity and material removal. The DIN 844 Type N specification denotes a long‑reach, centre‑cutting profile that enables limited plunge milling and through‑slotting while maintaining accuracy. For production environments seeking consistent cycle times, this design reduces the need for frequent tool changes and supports uninterrupted runs on medium‑duty milling tasks. Extended tool life thanks to TiCN and cobalt‑alloy steel Constructed from HSS‑Co and finished with a TiCN coating, the cutter resists adhesive wear and preserves edge integrity under elevated contact temperatures. The coating increases surface hardness and lowers friction, allowing the tool to handle higher specific cutting forces; uncoated operation is suitable up to roughly 800 N/mm², while the TiCN finish extends capability towards 1200 N/mm². The result is longer service life, fewer stoppages for regrinding and improved cost‑efficiency per component machined. Secure clamping and precise engagement for repeatable accuracy A Weldon shank with a 10 mm diameter drive flat ensures secure retention in standard tool holders, reducing slippage during heavy cuts. The cylindrical shank and balanced flute arrangement support concentricity and minimise run‑out, which in turn lowers vibration and produces cleaner surface finishes. Where tight tolerances matter, the combination of robust clamping and the tool’s centre‑cutting geometry keeps process variability to a minimum. Application guidance and material suitability This end mill is optimised for machining tasks in steel, stainless steel and castings—all rated as very well suited—while non‑ferrous metals and special alloys are listed as conditionally suitable. For operations involving medium‑strength materials, the coated variant is recommended to leverage the higher allowable cutting forces and enhanced wear resistance. When selecting cutting parameters, favour conservative feeds and increases in spindle speed only after verifying chatter behaviour; consult tooling data sheets or our technical team for specific feeds, speeds and coolant recommendations. For reliable procurement and application support of this TECWERK HSS‑Co end mill, contact Metav Werkzeuge today — our specialists in Emmerich will advise on compatibility, supply and optimal machining parameters. Technical Data Article number: 2000866400NW Standard: DIN 844 Brand: TECWERK Product type: End mill Material: HSS‑Co Coating: TiCN Package unit: 1 Facts Diameter: 8 mm Overall length: 88 mm Effective cutting length: 44 mm Shank diameter: 10 mm Flutes: 4 Relief: 7.5 mm Cutting direction: right‑hand Special features DIN 844 Type N — long, centre‑cutting Weldon shank with drive flat Cylindrical shank with drive flat Z = 4 (four flutes) Suitable for steel: very good Suitable for stainless steel: very good Suitable for non‑ferrous metals: limited suitability TiCN coating for extended tool life FAQ Is this end mill suitable for plunge cutting? The tool is centre‑cutting, so limited plunge operations are possible; full‑depth plunging should be validated for the specific workpiece and machine setup. What materials can be machined with this cutter? This TECWERK HSS‑Co end mill is very well suited to steel, stainless steel and castings; non‑ferrous metals and special alloys are conditionally suitable. What does the TiCN coating provide? The TiCN coating increases surface hardness and reduces friction, extending tool life and enabling higher cutting forces compared with the uncoated tool. Which shank type and diameter does the cutter use? The cutter features a Weldon shank with a 10 mm diameter and drive flat for secure clamping in standard holders. Can this cutter handle hardened steels? The tool is intended for low to medium strength materials; uncoated operation is suitable to about 800 N/mm², while the TiCN coated version extends capability nearer to 1200 N/mm² depending on application parameters. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from the combination of HSS‑Co PM construction, ALCRONA surface treatment and vibration‑reducing four‑flute geometry for precise, long‑lasting milling; order this end mill directly via Metav Werkzeuge or request application advice from our consultants. TECWERK End Mill DIN 844 Type N, 8 mm, HSS‑Co PM, ALCRONA, Weldon Shank — 4‑flute, short The TECWERK end mill DIN 844 Type N is a short, four‑flute cutter designed for stable slotting and peripheral milling of steels, stainless steel and cast iron up to approximately 1000 N/mm². HSS‑Co PM core for high toughness ALCRONA coating for extended tool life Four‑flute design with centre cutting Weldon shank, 10 mm shank diameter Reduced vibration through unequal flute spacing Precise performance through engineered materials and coating The short, Type N cutter combines a HSS‑Co PM substrate with an ALCRONA coating to deliver increased edge strength and wear resistance under intermittent and continuous cutting. Powder‑metallurgy high‑speed steel (HSS‑Co PM) offers a uniform microstructure that improves toughness compared with conventional grades; the coating reduces friction and thermal loading, which together extend service intervals and help maintain consistent part quality. This construction is especially beneficial where tool life and repeatable accuracy directly affect production throughput. Broad material suitability for workshop and industrial use Designed for a wide range of applications, the cutter is very well suited to steel, stainless steel and cast iron, while non‑ferrous metals and special alloys are workable with adapted parameters. The tool is specified for materials up to roughly 1000 N/mm², which covers many common structural steels and hardened components encountered in general engineering and toolroom environments. The centre‑cutting geometry permits plunge work and makes the tool suitable for slotting as well as side milling, increasing process flexibility. Geometry and clamping for improved rigidity and finish With an 8 mm cutting diameter, 4 cutting edges and a Weldon shank of 10 mm, the cutter offers a compact footprint that increases stiffness in the holder. The effective length 25 mm and short overall length (69 mm) reduce deflection during machining; a tapered flute root improves tool stiffness, while vibration reduction is achieved by unequal flute spacing. These design choices result in steadier cutting forces and a finer surface finish, particularly important for tight‑tolerance or thin‑walled components. Practical guidance for safe integration and process optimisation Use secure clamping and a compatible Weldon‑style holder to exploit the cutter’s stiffness advantages. Given the material range, select cutting speeds and feeds appropriate to the workpiece and machine rigidity; applying coolant or lubricant where recommended will prolong tool life and improve chip evacuation. For interrupted cuts or hard conditions, the HSS‑Co PM core and ALCRONA coating combine to resist chipping and thermal wear, reducing unplanned tool changes and supporting more stable cycle times. For reliable supply and application support, choose the TECWERK end mill via Metav Werkzeuge—fast delivery from Emmerich and personal technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000866033NW Standard: DIN 844 Product type: End mill (Type N) Brand: TECWERK Material: HSS‑Co PM Coating: ALCRONA Diameter: 8 mm Number of flutes: 4 Cutting length: 4 mm Effective length: 25 mm Overall length: 69 mm Shank diameter: 10 mm Shank type: Weldon Cutting direction: right‑handed Centre cutting: yes Packaging unit: 1 Facts Diameter: 8 mm Flutes: 4 Cutting length: 4 mm Effective length: 25 mm Overall length: 69 mm Shank diameter: 10 mm Special features Powder‑metallurgy HSS‑Co core ALCRONA surface coating Type N short design Weldon shank for secure clamping Centre‑cutting for plunge capability Unequal flute spacing for vibration reduction Tapered flute root for improved stiffness Very well suited: steel, stainless steel, cast iron Conditionally suited: non‑ferrous metals, special alloys FAQ Which materials can this end mill machine reliably? The TECWERK end mill (DIN 844 Type N, SKU 2000866033NW) is very well suited to steel, stainless steel and cast iron; non‑ferrous materials and special alloys are workable with adjusted cutting data. What does the ALCRONA coating provide? ALCRONA coating on this TECWERK cutter reduces friction and thermal wear, extending tool life and helping maintain cutting edge integrity under demanding conditions. Why choose a Weldon shank for this cutter? A Weldon shank provides secure clamping and improved torque transmission for the short, 8 mm cutter, enhancing rigidity and repeatability in milling operations. How does the cutter reduce vibration during milling? Unequal flute spacing and a tapered flute root on this four‑flute cutter help to disrupt harmonic excitation, resulting in lower vibration and a finer surface finish. Is the tool suitable for plunge cutting? Yes; the centre‑cutting geometry enables plunge cuts as well as slotting and peripheral milling with the TECWERK end mill. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of robust HSS‑Co PM construction and an ALCRONA wear barrier for consistent tool life and reliable finishing results. Order the tool via Metav Werkzeuge or contact the consultants for specification support. TECWERK End Mill DIN 844 — Ø 8 mm, HSS‑Co PM, ALCRONA‑coated, Weldon, 4 flutes, long The TECWERK end mill provides a long‑reach, centre‑cutting solution for demanding milling of steel, stainless steel and cast iron in production and toolroom environments. HSS‑Co PM base material with ALCRONA coating Four‑flute, centre‑cutting geometry for versatile milling Long reach with Weldon cylindrical shank for stability Optimised flute design for vibration reduction Deliver consistent material removal and extended tool life This long‑reach cutter is built from HSS‑Co PM, a powder‑metallurgy cobalt high‑speed steel that delivers improved toughness and wear resistance compared with conventional HSS. The ALCRONA coating adds a tribological barrier, reducing built‑up edge and extending tool life in intermittent or continuous cuts. With a Ø 8 mm cutting diameter and four flutes, the tool balances chip evacuation and surface finish: the multiple cutting edges reduce feed per tooth while maintaining material removal rates. The centre‑cutting geometry permits limited plunge milling and safe ramping into the workpiece, which broadens application options beyond purely peripheral passes. Improved stability and vibration control for better surface quality Designed for demanding setups, the cutter combines a Weldon shank with a cylindrical shaft featuring a drive flat for secure clamping in tool holders. The overall length 88 mm and effective length 44 mm give genuine long‑reach capability while retaining rigidity where it matters. Vibration is reduced by an unevenly divided flute pitch and a conical flute root that increases stiffness along the cutting edge—this translates into steadier cutting, fewer chatter marks and a more uniform finish. The short cutting length 4 mm and ground relief (7.5 mm relief) concentrate cutting forces where they are most effective, helping to protect the tool and the machine spindle in cantilevered setups. Clear application window and machining guidance The geometry and material combination make this cutter very well suited to steel, stainless steel and cast iron, with conditional suitability for non‑ferrous metals and special alloys. It is optimised for workpiece strengths of up to approximately 1000 N/mm², so it performs reliably in a broad range of industrial tasks from maintenance milling to component finishing. As a right‑hand cutting tool with four flutes and a centre‑cutting tip, it is a practical choice for slotting, pocketing and finishing operations where accessibility and surface quality are priorities. For secure assembly use holders compatible with a 10 mm shank diameter and a Weldon drive flat. Choose TECWERK’s precision end mill for demanding milling tasks and contact Metav Werkzeuge for tailored advice and prompt supply from Emmerich — info@metav-werkzeuge.com · +49 2822 7131930 Technical Data SKU: 2000866043NW Standard: DIN 844 Product type: End mill (Type N) Designation: long, centre cutting, 4 flutes Facts Diameter: Ø 8 mm Overall length: 88 mm Cutting length: 4 mm Effective length: 44 mm Shank diameter: 10 mm Flutes: 4 Cutting direction: right‑hand Special features Material: HSS‑Co PM Coating: ALCRONA Shank: cylindrical with Weldon drive flat Vibration reduction by uneven flute division Improved rigidity via conical flute root Suitability: very good for steel, stainless steel, cast iron Suitability: conditional for non‑ferrous metals and special alloys Centre‑cutting geometry FAQ What materials is this end mill suitable for? The TECWERK end mill is very well suited for steel, stainless steel and cast iron; it is conditionally suitable for non‑ferrous metals and special alloys. Can this cutter perform plunge operations? Yes. The centre‑cutting geometry allows for limited plunge milling and safe ramping into the workpiece, expanding its use beyond peripheral milling. What does the Weldon shank mean for clamping? A Weldon cylindrical shank provides a drive flat for secure clamping; the 10 mm shank diameter ensures compatibility with standard Weldon holders and reduces slippage during heavy cuts. How does the ALCRONA coating affect tool life? The ALCRONA coating improves wear resistance and reduces adhesion of workpiece material, which extends cutting life and helps maintain surface finish during interrupted cuts. Why choose a powder‑metallurgy HSS‑Co grade? The HSS‑Co PM substrate combines enhanced toughness and wear resistance, giving better edge retention under tougher milling conditions compared with conventional HSS. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

High-performance HSS‑Co PM substrate combined with an ALCRONA coating provides extended tool life and reliable performance in demanding steel applications. The short DIN 844 Type HR 4‑flute geometry and Weldon shank deliver increased rigidity and secure clamping for reduced vibration. Order the TECWERK end mill directly via Metav Werkzeuge or contact our consultants for tailored application advice. TECWERK End mill DIN 844 Type HR – 8 mm, HSS‑Co PM, ALCRONA‑coated The TECWERK short 4‑flute end mill is designed for robust milling of steels and stainless materials, offering centre‑cutting capability and a Weldon shank for reliable clamping in industrial toolholders. HSS‑Co PM substrate with ALCRONA coating DIN 844 Type HR short 4‑flute geometry Weldon shank with drive flat Suited for materials up to ≈ 1400 N/mm² tensile strength Consistent performance in demanding steel machining The HSS‑Co PM core provides a balance of toughness and wear resistance that benefits interrupted cuts and high‑load operations. With ALCRONA surface treatment, the tool shows improved resistance to adhesive wear and reduced built‑up edge, which extends service intervals and maintains surface finish quality. This combination is especially effective when machining steels and stainless materials that approach the upper tensile range indicated for the cutter. The result is predictable tool life and fewer unscheduled tool changes, supporting smoother production flow. Rigidity and control for accurate features Short overall geometry and a 4‑flute layout enhance stiffness and reduce overhang‑related deflection, which helps preserve dimensional accuracy in pocketing and contouring tasks. The 45° chamfer on the cutting edge gives a defined engagement that softens entry effects while the conical flute root increases shaft stiffness; together they reduce chatter and improve repeatability when producing milled features. For jobs requiring precise depths and clean edges, the cutter’s reduced projection and stiff design contribute directly to part quality. Secure clamping and straightforward integration on the shop floor A Weldon shank (drive flat) ensures positive drive transfer to standard toolholders, allowing rapid tool changes without complex adaptors. The 10 mm shank diameter and compact overall length reduce the need for long extensions, lowering the chance of vibration. Centre‑cutting geometry permits limited plunge operations, and the cutter is specified for reliable machining of steel, stainless steel and cast materials—non‑ferrous and certain special alloys are conditionally compatible. For complex applications or material mixes, Metav Werkzeuge’s technical team can supply additional cutting‑data guidance and holder recommendations. For reliable high‑strength milling with TECWERK’s HSS‑Co PM end mill, contact Metav Werkzeuge for availability and application support at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000866057NW Manufacturer: TECWERK Norm: DIN 844 Product type: End mill Material: HSS‑Co Coating: ALCRONA Facts Diameter: 8 mm Shank diameter: 10 mm Overall length: 69 mm Cutting length: 4 mm Effective length: 25 mm Free clearance: 7.5 mm Number of flutes: 4 Special features DIN 844 · Type HR · short version Weldon shank with drive flat 45° chamfer Centre cutting for limited plunging Right‑hand cutting Improved stiffness via conical flute root Suitability: Steel – very good; INOX – very good; Cast – very good; Non‑ferrous – conditionally; Special alloys – conditionally FAQ Is this cutter suitable for stainless steel applications? The TECWERK end mill is specified as very well suited for INOX; the HSS‑Co PM substrate and ALCRONA coating help maintain edge life and surface quality when machining stainless materials (SKU 2000866057NW). Can this cutter perform plunge cuts? Yes, the tool features centre‑cutting geometry, which allows limited plunge operations; the cutting length of 4 mm supports short plunges and entry cuts. Which clamping system is required for this tool? The cutter has a Weldon shank with a drive flat and a 10 mm shank diameter, designed for secure clamping in Weldon holders and standard setscrewed toolholders. For which materials is this end mill optimised? Optimised for steels and stainless steels (very good suitability) and cast materials; non‑ferrous metals and special alloys are conditionally suitable depending on cutting conditions. How does the ALCRONA coating improve performance? ALCRONA reduces adhesion and thermal wear on the cutting edges, extending tool life and improving consistent surface finish during prolonged milling of tougher materials. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from a high-performance combination of solid carbide construction, TiAlN coating and an extra‑long flute for deep-pocket machining; the result is reliable removal rates and consistent surface quality. Order the TECWERK solid carbide end mill D 8 mm, Z6, TiAlN directly via Metav Werkzeuge or ask our consultants for application support. TECWERK solid carbide end mill D8 mm – TiAlN-coated, 6-flute, extra-long A TECWERK solid carbide end mill D8 mm engineered for universal roughing and finishing, suitable for steel, cast iron, stainless and non-ferrous alloys in CNC and workshop applications. TiAlN coating for high heat resistance Extra-long flute for deep-pocket machining Six flutes for high feed and fine finish Cylindrical shank DIN 6535 HB, tolerance h6 Consistent performance for demanding roughing and finishing Constructed from solid carbide (VHM) and designed with six cutting edges, this cutter offers a balance between material removal and surface quality. The multi-flute concept permits higher feed rates while keeping a fine finish on the workpiece; fewer passes are needed in many operations. The combination of a longer effective cutting length and a stable flute geometry reduces interruptions for tool changes, supporting continuous production and shorter cycle times. Coating and geometry that extend tool life The TiAlN coating increases thermal resistance and reduces adhesion at the cutting zone, which translates into longer tool life during dry or high-temperature machining. The moderate 35–38° helix angle promotes effective chip evacuation while the 45° protection chamfer (0.12 mm) minimises chipping at entry. An unequal pitch and a neck relief (hollowed shank area) lower vibration, enabling stable high-speed operation and reliable dimensional results on the finished component. Broad material suitability to reduce tooling inventory This end mill is specified for universal use across a wide range of materials: steel, cast iron, temper cast, Cr‑Ni steels, stainless (INOX), non‑ferrous metals, aluminium with silicon content, special alloys and abrasives. The tool’s geometry and coating make it very well suited to both roughing heavy sections and performing finishing passes on demanding alloys, meaning fewer dedicated cutters are required and setup times are reduced. Machine integration and concentricity for repeatable accuracy The cutter features a cylindrical shank to DIN 6535 HB with h6 tolerance, ensuring concentric clamping and minimal runout in collets and chucks. Key dimensions such as an 8 mm diameter, 30 mm effective length, 6 mm cutting length and 68 mm overall length allow straightforward integration into existing toolholders and programming cycles. The right‑hand cutting direction and fine‑grain carbide core support predictable tool behaviour under varied feed and speed settings. Request specification advice or place an order through Metav Werkzeuge for reliable supply of the TECWERK extra‑long TiAlN‑coated solid carbide end mill; Metav Werkzeuge provides fast delivery and technical guidance from Emmerich — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical Data Article number: 2000866878NW Norm: DIN 6527 SKU: 2000866878NW Manufacturer: TECWERK Facts Diameter: 8 mm Effective length: 30 mm Overall length: 68 mm Cutting length: 6 mm Flutes: 6 Helix angle: 35–38° Protection chamfer: 0.12 mm Free relief: 7.7 mm Shank diameter: 8 mm Shank tolerance: h6 Cutting direction: right-hand Special features Material: solid carbide (VHM), universal fine grain Coating: TiAlN Extra-long design for deep-pocket machining Cylindrical shank to DIN 6535 HB Unequal pitch for vibration reduction Neck relief for low-vibration performance 45° protection chamfer Suitable for steel, cast iron, stainless, non‑ferrous, special alloys, aluminium with silicon and abrasive materials Works for roughing and finishing FAQ What materials can this end mill machine effectively? The TECWERK solid carbide end mill (SKU 2000866878NW) is specified for steel, cast iron, temper cast, Cr‑Ni steels, stainless (INOX), non‑ferrous metals, aluminium with silicon content, special alloys and abrasive materials. How does the TiAlN coating benefit machining? TiAlN on this cutter increases heat resistance and lowers adhesion at the cutting edge, which extends tool life and improves performance during high-temperature or high-speed operations. Is the shank compatible with standard holders? Yes — the cylindrical shank is made to DIN 6535 HB with h6 tolerance, ensuring accurate clamping and minimal runout in common collets and chucks. What machining tasks is this cutter best suited for? The tool’s extra‑long geometry and six-flute layout make it suitable for deep-pocket roughing as well as finishing passes where a fine surface is required, especially in serial CNC operations. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Benefit from a combination of solid carbide construction, multilayer TiAlN wear protection and a 45° helix for reliable stability in both roughing and finishing; order directly via Metav Werkzeuge or contact the consultants for application support. TECWERK Solid Carbide End Mill DIN 6527 L — Ø 8 mm, TiAlN, 45° The TECWERK solid carbide end mill DIN 6527 L is a long, four-flute tool engineered for universal roughing and finishing tasks, especially on steel and stainless materials, with a cylindrical shank to DIN 6535 HB. Solid carbide construction (VHM) Multilayer TiAlN coating 45° helix for high stability Designed for roughing and finishing Stable cutting for higher metal removal rates The tool's solid carbide body and a special flute geometry provide enhanced rigidity and vibration resistance, which translates directly into higher metal removal rates and consistent tool life. The 45° helix angle improves axial engagement and distributes cutting forces evenly across the cutting edges, reducing chatter during aggressive passes. By choosing a long-flute design with a four-flute layout, the cutter balances efficient chip evacuation with a larger shear zone, yielding productive machining cycles without sacrificing dimensional control. Surface quality that meets finishing requirements Thanks to the combination of the fine flute geometry and the tool's four cutting edges, the end mill produces a notable surface finish even when used for roughing followed by light finishing passes. The short cutting length together with the long overall profile gives access to deeper features while maintaining stiffness close to the cut, reducing deflection and enabling tighter form and position tolerances. For applications where the final surface quality matters, the geometry supports reduced rework and shorter downstream processing. Multilayer TiAlN for thermal and wear resistance The multilayer TiAlN coating offers improved adhesion and a protective barrier against abrasive wear and high temperatures, extending tool life in demanding operations. TiAlN also provides excellent oxidation resistance, which is particularly advantageous when machining stainless-steel grades where heat generation at the cutting edge is critical. The coating’s temperature stability helps to maintain edge integrity during interrupted cuts and heavier engagements, making the cutter suitable for both continuous and semi-interrupted machining conditions. Versatile application and practical features for workshop use Equipped with a chipbreaker and an unequal pitch, the cutter reduces harmonic excitation and improves chip control across a range of materials. Material suitability is optimised for steel and stainless steel, while non-ferrous metals, special alloys and cast iron are conditionally supported depending on cutting parameters. The tool adopts a cylindrical shank to DIN 6535 HB, ensuring secure clamping in standard toolholders and enabling predictable runout performance for high-precision tasks. For tailored parameter recommendations, technical consultation is available to align cutter selection with machine capability and workpiece requirements. Contact Metav Werkzeuge for advice on selecting the correct TECWERK long solid carbide end mill for the intended application — expert support and reliable supply from Emmerich are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 2000866687NW Standard: DIN 6527 Brand: TECWERK Product type: End mill Dimensions & core data Diameter: 8 mm Overall length: 63 mm Cutting length: 4 mm Shank diameter: 8 mm Flutes: 4 Helix angle: 45° Cutting direction: right-hand Materials & special features Material: solid carbide (VHM) Coating: TiAlN (multilayer) Shank: cylindrical shank to DIN 6535 HB With chipbreaker and unequal pitch Type: DIN 6527 L, Type NF, long Suitability steel: very good Suitability stainless steel: very good Suitability non-ferrous metals: conditional Suitability special alloys: conditional Suitability cast iron: conditional FAQ What materials is this cutter best suited for? The TECWERK solid carbide end mill is optimised for steel and stainless steel, offering very good performance on these materials; non-ferrous metals, special alloys and cast iron are conditionally supported depending on cutting strategy and parameters. Does the TiAlN coating improve performance for stainless steel? Yes, the multilayer TiAlN coating on the TECWERK cutter provides thermal stability and wear resistance that help maintain edge life and surface quality when machining stainless steel. How does the 45° helix influence machining? A 45° helix reduces cutting force peaks and promotes smoother cutting action, which increases stability and reduces chatter during both roughing and finishing operations with this long four-flute cutter. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Benefit from the combination of PM HSS‑Co construction, ALCRONA coating and a Weldon shank for dependable long‑reach milling performance; order the cutter directly via Metav Werkzeuge or consult our specialists for tailored cutting parameters. End mill DIN 844 Type HR, 8 mm, HSS‑Co PM, ALCRONA coated — TECWERK The End mill DIN 844 Type HR D8 mm is a long, 4‑flute HSS‑Co end mill with centre cut and Weldon shank, designed for machining steels and stainless steel up to approximately 1400 N/mm². PM HSS‑Co body with ALCRONA coating Weldon shank with drive flat for secure clamping Centre‑cut geometry for limited plunging Long reach with improved stiffness Very good for steel and stainless steel Precise material pairing for consistent results The tool combines PM HSS‑Co metallurgy with an ALCRONA surface treatment to deliver enhanced wear resistance and thermal stability during interrupted cuts. Conforming to DIN 844 and specified as Type HR, the geometry is optimised for cutting forces typical of steels and INOX with tensile strengths up to ~1400 N/mm². The combination of powder‑metallurgy steel and hard coating reduces flank wear and extends tool life, meaning more consistent part tolerances and fewer tool changes over a production run. Robust design that keeps machining stable A Weldon shank with a 10 mm drive flat and a 45° protective chamfer secure the tool under heavy feed and rapid direction changes. The centre‑cut capability allows direct plunging for short depths, while the 4‑flute layout balances chip evacuation and radial stiffness. With an effective length of 44 mm and an overall length of 88 mm, the long‑reach profile plus a conical flute root improves bending stiffness, reducing chatter risk and producing superior surface finish in through‑slot and shoulder milling operations. Productivity advantages in the workshop or on the shop floor The cutter’s short cutting length of 4 mm and the geometry tuned for right‑hand cutting help to keep forces predictable and cycle times stable. Tool life gains from the ALCRONA layer and HSS‑Co PM substrate translate into lower tooling consumption and less downtime for replacements. Suitability ratings indicate the cutter is very good for steel, stainless steel and cast materials, and conditionally suitable for non‑ferrous and special alloys — a practical choice where a single tool must cover a range of medium‑duty tasks while delivering repeatable quality and efficiency. Contact Metav Werkzeuge for personalised cutting data or to arrange supply of this TECWERK end mill through our Emmerich hub. Technical Data Article number: 2000866071NW SKU: 2000866071NW Standard: DIN 844 Brand: TECWERK Facts Diameter: 8 mm Overall length: 88 mm Effective length: 44 mm Cutting length: 4 mm Shank diameter: 10 mm Number of flutes: 4 Free relief: 7.5 mm Cutting direction: right‑handed Packaging unit: 1 Special features Material: HSS‑Co PM Coating: ALCRONA Type: HR, long Geometry: centre‑cut, 45° protective chamfer Shank: Weldon shank with drive flat Application: machining up to approx. 1400 N/mm² tensile strength Material suitability: very good for steel, inox and cast; conditional for NE‑metals and special alloys Design advantage: improved stiffness via tapered flute root FAQ What materials is the TECWERK end mill suitable for? The TECWERK end mill is rated very good for steel, stainless steel and cast materials and conditionally suitable for non‑ferrous metals and special alloys; suitable up to around 1400 N/mm² tensile strength. Can this tool perform plunging operations? Yes, the centre‑cut geometry enables limited plunging and helical entry; the end mill is specified as centre‑cut to allow direct engagement where necessary. What is the shank type and how is it clamped? The cutter features a Weldon shank with a 10 mm drive flat to ensure secure clamping and reliable torque transmission in standard toolholders. How does the ALCRONA coating help in production? ALCRONA coating increases wear resistance and reduces built‑up edge tendency, which lengthens tool life and maintains surface quality under higher temperatures and interrupted cuts. Which standard does this cutter follow? The tool conforms to DIN 844, Type HR, specifying dimensions and tolerances for long straight‑flute end mills. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of a DIN 844‑compliant short end mill that combines HSS‑Co5 substrate with a TiCN coating for extended tool life and reliable machining; the Weldon shank ensures secure clamping for repeatable results. Order directly via Metav Werkzeuge or consult our specialists for application advice. TECWERK End mill DIN 844 Type NR, Ø8 mm — HSS‑Co5, TiCN, Weldon shank The TECWERK End mill DIN 844 Type NR is a short, multi‑flute cutter designed for accurate machining of steel and cast iron, offering centre cutting and high clamping stability for workshop and light industrial use DIN 844 short multi‑flute design HSS‑Co5 with TiCN coating for wear resistance Weldon shank with drive flat for secure clamping Predictable performance through standardised geometry Built to DIN 844, this short multi‑flute end mill delivers consistent cutting geometry that reduces process variation and simplifies tool selection. The combination of a HSS‑Co5 substrate and a TiCN coating provides a balance between toughness and surface hardness, enabling reliable edge retention under interrupted cuts. With a Ø8 mm cutter diameter and an effective length of 25 mm, the tool offers predictable engagement volumes, which supports stable cycle times and consistent part quality in serial production. Longer life and improved surface finish with the right coating The TiCN (titanium carbonitride) layer increases surface hardness and lowers friction, which reduces built‑up edge and improves finish on ferrous materials. The cobalt content in HSS‑Co5 improves red hardness and thermal resistance compared with standard HSS, allowing higher machining temperatures before hardness loss. Together these materials extend tool life and maintain dimensional accuracy over longer runs, making the cutter a cost‑effective choice for repetitive milling tasks where component quality matters. Secure clamping and vibration‑resistant machining A Weldon shank with drive flat and a 10 mm shank diameter provides a positive location in holders, reducing slippage and runout at the toolholder interface. The tool’s overall length of 69 mm and short design increase stiffness, while the 3‑flute geometry balances chip evacuation and cutting edge strength. These features reduce chatter and support reproducible toolpaths, which is particularly beneficial when machining prismatic parts or when tight tolerances are required. Clear guidance on applications and material suitability This short end mill is optimised for materials of low to medium strength: it is very well suited to steel and cast iron, while non‑ferrous and special alloys are conditionally machinable with adapted cutting data. The geometry includes a centre cutting capability and a 45° protective chamfer, enabling limited plunge cuts and reliable entry into workpieces. For steels up to 800 N/mm² with an uncoated tool and up to 1000 N/mm² when coated, the tool offers dependable performance; adjust feeds and speeds according to machine rigidity and workholding for best results. Select the TECWERK HSS‑Co5 TiCN short end mill for robust workshop performance — order via Metav Werkzeuge or contact our consultants at info@metav-werkzeuge.com or +49 2822 7131930 for specific machining recommendations. Technical data Article number: 2000866469NW Label: Schaftfräser DIN 844 Typ NR D.8mm Einsatz‑L.25mm HSS‑Co5 TiCN Weldon TW Standard: DIN 844 Manufacturer: TECWERK Facts Diameter: 8 mm Overall length: 69 mm Effective length: 25 mm Shank diameter: 10 mm Number of flutes: 3 Free relief: 7.5 mm Cutting direction: right‑hand cutting Special features Material: HSS‑Co5 (cobalt high‑speed steel) Coating: TiCN (titanium carbonitride) Type NR, short multi‑flute 45° protective chamfer Centre cutting Relieved flute profile Weldon shank with drive flat Very well suited to steel Very well suited to cast iron Conditionally suited to non‑ferrous metals, special alloys and stainless steel FAQ What materials is this end mill best suited to? The TECWERK end mill (SKU 2000866469NW) is very well suited to steel and cast iron; non‑ferrous metals, stainless steel and special alloys are conditionally machinable with adapted cutting data. Can this cutter be used for plunge milling? Yes. Because the cutter is centre cutting, the tool allows limited plunge operations; use conservative feeds when plunging to preserve edge life. How does the Weldon shank affect clamping? The Weldon shank with drive flat and a 10 mm shank diameter gives secure clamping and reduced slippage, improving runout stability for the TECWERK end mill (2000866469NW). What performance benefit does the TiCN coating provide? The TiCN coating increases surface hardness and reduces friction, which lowers built‑up edge formation and improves surface finish and tool life under elevated temperatures. Which standard and geometry does the tool conform to? The cutter conforms to DIN 844 and features a short multi‑flute Type NR geometry with a 45° protective chamfer, a relieved flute profile and right‑hand cutting. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund

Take advantage of the combination of solid carbide rigidity, TiAlN heat protection and an HPC geometry that reduces vibration for reliable roughing and finishing in demanding materials; order the cutter directly via Metav Werkzeuge or ask our consultants if needed. TECWERK WN Type N solid carbide end mill — 8 mm, TiAlN, 35° helix The TECWERK WN Type N solid carbide end mill is an extra-short, 4-flute cutter designed for high-feed roughing, fine finishing and slotting across steels, cast iron and non-ferrous materials. Solid carbide VHM for high rigidity TiAlN coating for heat resistance 35° helix and 4 flutes for fast chip evacuation Centre-cut design for plunge milling Reliable performance and extended tool life for production Built from VHM (solid carbide) and finished with a TiAlN coating, this cutter prioritises thermal stability and wear resistance to support continuous machining. The proven HPC geometry with unequal pitch reduces harmonics and chatter, which allows higher feed rates and fewer tool changes in production runs. As a result, cycle times fall and process reliability improves — a clear benefit for job shops and serial production environments that require consistently reproducible results. Accurate results across a wide material spectrum The tool delivers precise cuts thanks to its centre-cut capability and compact cutting length of 4 mm, enabling controlled plunge operations and narrow-slot work without special plunging tools. The 8 mm diameter and optimised flute geometry produce good surface finish and dimensional stability when machining steel up to 45 HRC, cast iron, aluminium, copper and brass; INOX and other non-ferrous materials are conditionally suitable. Technical terms: centre-cut means the end is ground to allow axial entry; HRC denotes hardness on the Rockwell C scale. Stable clamping and machine compatibility for vibration-free work An extra-short overall length (50 mm) and a cylindrical shank manufactured to DIN 6535 HB with h6 tolerance ensure secure clamping and reduced overhang, promoting vibration-free machining even on smaller machines. The 35° helix supports efficient chip evacuation while the 45° protective chamfer (0.2 mm) improves flank strength at the cutting edge. With a right-hand cutting direction and a soft 10° cutting action, the tool is tailored for balanced material removal during both roughing and finishing passes. Contact Metav Werkzeuge for tailored recommendations on integrating the TECWERK WN Type N end mill into existing workflows — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical Data Article number: 2000866415NW Norm: DIN 6527 Label: Schaftfräser WN TypN D.8mm VHM TiAlN 35Grad HB Z.4 ext.kurz TECWERK Core data Diameter: 8 mm Overall length: 50 mm Cutting length: 4 mm Shank diameter: 8 mm Number of flutes: 4 Helix angle: 35° Cutting direction: right-hand Shank standard: DIN 6535 HB Materials & features Material: VHM (solid carbide) Coating: TiAlN Geometry: HPC with unequal pitch, centre-cut, 45° protective chamfer 0.2 mm Shank tolerance: h6 Application: Steel up to 45 HRC; cast iron; aluminium; copper; brass; INOX (conditionally) Use: Roughing, finishing and slotting; vibration-reduced machining FAQ Which materials is this cutter best suited for? The TECWERK WN Type N end mill is very well suited for steel up to 45 HRC and cast iron; it is also suitable for aluminium, copper and brass, with INOX and some non‑ferrous alloys being conditionally machinable. Can the tool perform plunge cuts or drilling entries? Yes. The centre-cut geometry allows axial entry and controlled plunge milling, making the tool suitable for slotting and interrupted cuts without pre-drilling. What advantages does the TiAlN coating provide? The TiAlN coating increases thermal resistance and reduces adhesion of built-up edge, which extends tool life under high-temperature cutting conditions and supports higher cutting speeds. Is the shank compatible with standard toolholders? The cylindrical shank conforms to DIN 6535 HB with h6 tolerance, ensuring precision clamping in collets and standard toolholders for stable machining. What operations are recommended with this cutter? Recommended operations are high-performance roughing (HPC), finishing and slotting where low vibration and high surface quality are required; the cutter’s geometry is optimised for efficient material removal. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund

Data inconsistency detected Contradictory values for cutting length: 'schnittlange' = 4 mm versus 'effektive_lange' = 20 mm (the label specifies a 20 mm cutting length). These conflicting measurements create uncertainty regarding the actual cutting length of the product, making it difficult to determine which value is accurate. Without clarification or correction of this discrepancy, it is impossible to ensure the reliability of the information provided. A reliable product description cannot be generated due to these inconsistent data, as the inconsistency undermines the credibility of the specifications and may lead to confusion or errors in usage.