GX24-3E500N04-UD4 WKP13S WKP13S Wendeplatten - Walter Tools
Benefit from the Tiger‑tec Silver coating and the WKP13S grade for sustained tool life and consistent chip control in steel and cast iron turning; the coated carbide insert delivers productive machining with reliable edge performance. Order the insert directly via Metav Werkzeuge or consult our specialists for application support. GX24-3E500N04-UD4 WKP13S — Turning insert, Tiger‑tec Silver (Walter Tools) A GX24-3E500N04-UD4 WKP13S indexable turning insert engineered for productive turning of steel and cast iron, offering optimised chip formation and durable coated carbide performance Tiger‑tec Silver coating for extended tool life Optimised chip formation for stable cutting Coated carbide grade WKP13S for steels and cast iron Consistent edge for productive turning Longer tool life through advanced coating and grade The combination of the Tiger‑tec Silver series and the WKP13S grade provides measurable improvements in wear resistance and process stability. The insert is manufactured from a coated carbide substrate; the coating reduces flank wear and thermal softening during continuous turning, which translates to longer cutting intervals and fewer tool changes. For batch and series production this means higher uptime and reduced cycle-time variation. The technical advantage of a coated carbide insert is that the hard surface layer resists abrasive wear while the substrate maintains toughness, balancing life and reliability. Controlled chips and improved surface quality The integrated chipbreaker 3E500N04‑UD4 is designed to produce predictable, segmented chips in both steel (ISO group P) and cast iron (ISO group K). Optimised chip control reduces the risk of tangled or long stringy chips, improves coolant access to the cutting zone and supports a stable cutting force. As a result, the need for secondary finishing can be diminished and dimensional consistency rises. In practice, this leads to fewer machine stops for chip clearance, safer operation and a cleaner shop floor. Broad applicability with consistent performance Designed within the Tiger‑tec Silver family, this insert suits a wide range of turning tasks where a balance of productivity and tool life is required. The WKP13S specification targets common steels and cast irons and is catalogued for general-purpose turning geometries. For operations seeking repeatable results, the insert delivers consistent cutting edges and predictable wear behaviour, supporting process reproducibility and efficient tool management. Where higher speeds and steady material removal rates are part of the machining strategy, the geometry and grade provide a pragmatic compromise between aggressiveness and longevity. Contact Metav Werkzeuge for tailored advice on the Walter Tools GX24-3E500N04-UD4 WKP13S insert — e‑mail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: GX24-3E500N04-UD4-WKP13S-WALTER Series: Tiger‑tec Silver Grade: WKP13S Chipbreaker: 3E500N04‑UD4 Product type: Turning insert Facts Suitable for ISO groups: P (steel) and K (cast iron) Material base: coated carbide Type designation: GX24-3E500N04-UD4 WKP13S Special features Coating technology: Tiger‑tec Silver Application: productive turning of steel and cast iron Optimised chip formation for stable cutting Reliable edge for repetitive machining FAQ What materials can be machined with this insert? The insert is specified for ISO groups P and K, meaning it is suitable for machining steels and cast iron; the WKP13S grade and Tiger‑tec Silver coating are optimised for these material families. How does the Tiger‑tec Silver coating benefit production? The Tiger‑tec Silver coating reduces abrasive wear and thermal effects on the cutting edge, extending tool life and supporting longer uninterrupted cutting, which improves overall production efficiency. Which chipbreaker is fitted and what is its effect? The chipbreaker 3E500N04‑UD4 produces segmented chips for safer evacuation and more consistent cutting forces, enhancing surface finish and reducing the need for manual chip clearing. Is this insert suitable for high-speed turning? The coated carbide construction and grade WKP13S allow increased cutting speeds compared with uncoated grades; actual speed suitability depends on workpiece, toolholder and machine parameters. Can the insert be used for finishing and roughing operations? The insert’s geometry and grade provide a balance between wear resistance and toughness, making it applicable for medium-turning tasks; tool life and surface quality determine specific suitability for roughing or finishing. Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are used for explanation only. There is no affiliation between our company and the mentioned brands. The offered article is an original factory-new product of the manufacturer. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
GX24-3E500N04-UD4 WKP23S Wendeplatten - Walter Tools
The combination of Tiger·tec Silver coating and the WKP23S carbide grade ensures consistent tool life and reliable chip control for steel and cast iron machining; benefit from improved productivity and lower tool-change frequency. Order the turning insert directly via Metav Werkzeuge or consult the advisors for application support. GX24-3E500N04-UD4 WKP23S Indexable Turning Insert — Tiger·tec Silver for Steel & Cast Iron (Walter Tools) The GX24-3E500N04-UD4 WKP23S is a high-performance indexable turning insert designed for productive machining of steel and cast iron in demanding industrial turning operations. Tiger·tec Silver coating for extended tool life Optimised for ISO P and K materials Reliable chip control and stable cutting Coated carbide grade WKP23S for productivity Longer tool life through advanced coating technology The insert features the Tiger·tec Silver coating paired with the WKP23S coated carbide, a combination engineered to resist abrasive wear and thermal loading typical in turning steels and cast irons. This coating system reduces flank wear and improves resistance to built-up edge, which translates into longer intervals between tool changes and fewer unscheduled stops. The technical advantage lies in heat and wear management: the coating lowers friction at the cutting zone, enabling higher cutting parameters while maintaining dimensional constancy and repeatable performance. Consistent chip control for safer, faster turning Equipped with the 3E500N04-UD4 chipbreaker, the insert delivers reliable chip control and predictable chip forms when cutting ISO P (steel) and ISO K (cast iron) materials. Stable chip formation reduces the risk of entanglement and tool damage, decreasing operator intervention and scrap rates. For production environments where cycle times and safety matter, the geometry contributes to smoother feed behaviour and consistent surface integrity, supporting faster cycle times without compromising process stability. Productivity gains in mixed-material production Designed for shops that machine a variety of ferrous materials, this grade supports high-productivity turning operations across unalloyed, alloyed steels and cast iron. The optimisation for both ISO groups makes tool planning simpler and reduces tooling variants on the shelf, helping to streamline logistics and lower total cost of ownership. The engineered balance between toughness and hardness in the cutting grade delivers a useful compromise: it resists chipping on interrupted cuts while offering sufficient hardness for abrasive cast-iron applications, enabling a stable, economical machining process. Practical integration and handling benefits The insert’s standard designation and geometry make it compatible with common clamping systems and toolholder families, easing retrofit into existing tooling setups. With predictable wear characteristics, planning for tool replacement becomes straightforward and maintenance cycles can be scheduled with confidence. For production planners, the result is fewer machine stoppages, less operator rework and a measurable improvement in overall throughput. Technical advisors are available to assist in selecting the correct holder or adjusting parameters to match specific machine and material conditions. For high-productivity turning with Walter Tools' Tiger·tec Silver grade, contact Metav Werkzeuge for tailored application advice or to place an order via e‑mail info@metav-werkzeuge.com or telephone +49 2822 7131930. Technical Data Article number: GX24-3E500N04-UD4-WKP23S-WALTER Product: Indexable turning insert GX24-3E500N04-UD4 WKP23S, Walter Tools Series: Tiger·tec Silver Grade: WKP23S Chipbreaker: 3E500N04-UD4 Data Material suitability: P (steel), K (cast iron) Coating: Tiger·tec Silver Cutting material class: coated carbide Special features Optimised for ISO P and K applications Stable chip control and reduced built-up edge Designed for productive turning and consistent tool life FAQ What materials is this insert suitable for? This insert is optimised for machining steel and cast iron; the grade WKP23S and the Tiger·tec Silver coating are adapted to ISO P and ISO K material groups. How does the Tiger·tec Silver coating improve performance? The Tiger·tec Silver coating reduces friction and improves heat resistance, which extends tool life and allows higher cutting parameters with consistent surface finish on turned parts. Is the chipbreaker suitable for interrupted cuts? Yes, the 3E500N04-UD4 chipbreaker provides controlled chip formation and a robust cutting edge that performs reliably in many interrupted and continuous turning operations. Can this insert be used in existing toolholders? The insert follows standard indexable insert conventions and is compatible with commonly used turning toolholders; alignment and clamping depend on the specific holder geometry. Which Walter Tools series does this insert belong to? The insert is part of the Tiger·tec Silver series and uses the WKP23S coated-carbide grade for a balance of wear resistance and toughness. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Walter AG (brand appearance: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered article is original, factory-new goods of the manufacturer.
GX24-3E500N04-UD4 WKP33S WKP33S Wendeplatten - Walter Tools
Benefit from a combination of reliable productivity and broad material coverage: the Tiger‑tec Silver WKP33S grade delivers stable chip formation and enhanced wear resistance for turning in steel and cast iron; order or request application advice via Metav Werkzeuge for immediate planning and supply. GX24-3E500N04-UD4 WKP33S – Indexable turning insert for steel and cast iron, Walter Tools The GX24-3E500N04-UD4 WKP33S is a coated carbide indexable insert engineered for productive turning in P and K material groups, offering consistent performance in series Tiger‑tec Silver. Tiger‑tec Silver coated carbide grade Designed for steel and cast iron Stable chip formation and wear resistance GX24 geometry for predictable edge control Faster, more predictable machining with Tiger‑tec Silver The Tiger‑tec Silver coating and the WKP33S cutting grade are designed to raise process reliability when machining steels and cast irons. The coating enhances thermal resistance and reduces adhesive wear, which leads to longer edge life and fewer index changes. For manufacturing environments where cycle times and repeatability matter, this combination supports higher material removal rates while maintaining dimensional consistency, translating into measurable productivity gains. Geometry and chip control that reduce downtime The insert’s geometry GX24-3E500N04-UD4 (chipbreaker 3E500N04‑UD4) provides reliable chip control and stable cutting conditions across a range of feeds and depths. A well‑defined chipbreaker prevents long, stringy chips and minimises interruption to automated turning cycles, which improves surface finish and reduces secondary operations. For workshop planners, the predictable behaviour of the insert simplifies parameter setup on CNC lathes and reduces the time spent on troubleshooting. Practical benefits for production environments As a coated indexable insert intended for ISO groups P (steel) and K (cast iron), the component suits serial production and jobbing alike. The coated carbide construction contributes to consistent performance under the heat and abrasion typical of these materials. For maintenance planners and buyers, the insert’s robustness offers lower tool consumption per part and more stable process windows, supporting cost‑efficient machining and fewer unscheduled tool changes. For tailored machining parameters, availability and stocking options for Walter Tools Tiger‑tec Silver inserts, please contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss applications and supply. Technical data SKU: GX24-3E500N04-UD4-WKP33S-WALTER Designation: GX24-3E500N04-UD4 WKP33S Product type: Indexable turning insert Brand: Walter Tools Core data ISO groups: P (steel), K (cast iron) Series: Tiger‑tec Silver Geometry designation: GX24-3E500N04-UD4 Special features Grade: WKP33S (coated carbide) Chipbreaker: 3E500N04-UD4 Material suitability: Steel and cast iron (ISO 513) Material code: P / K FAQ What materials is this insert suitable for? The GX24-3E500N04-UD4 WKP33S insert is specified for ISO groups P and K, making it suitable for a broad range of steels and cast irons. How does the Tiger‑tec Silver coating benefit machining? Tiger‑tec Silver improves thermal stability and wear resistance on the WKP33S grade, which helps maintain edge life and reduces tool changes during prolonged turning operations. Which chipbreaker is integrated in this insert? This indexable insert features the 3E500N04‑UD4 chipbreaker geometry, developed for predictable chip formation and efficient evacuation in turning processes. Is this insert intended for roughing or finishing? The combination of geometry and the WKP33S grade allows flexible use in both higher‑productivity roughing and stable finishing operations, depending on cutting parameters. Can the insert be used on automated turning centres? Yes; the predictable chip control and coated carbide grade make the insert well suited to CNC lathe environments with automated handling and long continuous cycles. Walter Tools (Walter AG) is a global precision tooling brand and part of the Sandvik Group; head office in Tübingen, Germany; brand and product names are the property of their respective owners. The Walter AG (brand appearance: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and forms part of the Swedish Sandvik group.
GX24-3E500N04-UD4 WSM33S WSM33S Wendeplatten - Walter Tools
Take advantage of Tiger·tec Silver performance and the WSM33S grade for reliable machining of stainless steels and heat‑resistant alloys, combining durable cutting edges with controlled chip formation for consistent productivity; order through Metav Werkzeuge or contact the consultants for application support. GX24-3E500N04-UD4 WSM33S Drehwendeschneidplatte – Tiger·tec Silver grade by Walter Tools The GX24-3E500N04-UD4 WSM33S is an indexable turning insert engineered for heavy duty machining of stainless steels and heat‑resistant superalloys, offering wear resistance and stable edge performance under thermal stress Tiger·tec Silver coating for high heat resistance WSM33S grade optimised for stainless and superalloys Chipbreaker geometry 3E500N04-UD4 for reliable chip control Robust cutting edge for extended process stability Exceptional grade for tough materials and longer tool life The WSM33S grade, realised through the Tiger·tec Silver coating technology, provides a technical edge when machining demanding alloys. Coated cemented carbide combines a thermally resistant surface with a tough substrate to reduce wear rates and mitigate edge degradation under elevated temperatures. This results in extended tool life and fewer interruptions in production, which supports predictable cycle times and lower total machining costs. The formulation targets materials classified as M (stainless steels) and S (heat‑resistant superalloys, titanium), where reliable heat management and stable edge behaviour are critical for avoiding built‑up edge and premature tool failure. Precise chip control that improves surface quality The insert’s chipbreaker, designated 3E500N04‑UD4, is designed to form short, controllable chips in a wide range of turning operations. A consistent chip flow reduces the risk of workpiece damage and minimises the need for secondary cleaning, thus improving first‑pass yield. For operators transitioning from uncoated grades, this geometry helps maintain a consistent surface finish and simplifies handling at the machine, particularly in interrupted cuts and variable engagement conditions. The controlled chip evacuation also contributes to safer, more efficient production cycles and reduces downtime caused by chip entanglement. Practical machining benefits and process integration As a turning indexable insert, the component integrates into standard toolholders for straightforward replacement and repeatable positioning, enabling stable tolerances over serial production. The coated carbide structure supports both roughing and finishing when the correct insert geometry and cutting parameters are chosen; the selection of the WSM33S grade is particularly advantageous for operations where heat generation and work hardening are concerns. For process planners, this means fewer tool changes and greater consistency across batches. If additional machining data or recommendations for holder compatibility are required, Metav Werkzeuge’s technical advisors are available to assist with application matching and parameter optimisation. Reliability, brand backing and workshop confidence Manufactured by Walter Tools, this turning insert reflects a focus on process reliability and repeatable results. Using a well‑matched grade and chipbreaker reduces the incidence of unexpected tool wear, contributing to predictable maintenance intervals and more efficient production planning. The product’s design emphasis on chip control and thermal resilience addresses two of the most common causes of machining variability when working with stainless steels and superalloys, supporting higher uptime and consistent part quality. Contact Metav Werkzeuge for tailored application advice on Walter Tools Tiger·tec Silver inserts or to arrange a technical consultation for optimal integration into existing turning processes Technical data SKU: GX24-3E500N04-UD4-WSM33S-WALTER Designation: GX24-3E500N04-UD4 WSM33S Product type: Drehwendeschneidplatte (indexable turning insert) Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WSM33S Chipbreaker: 3E500N04-UD4 Facts Numerical specifications: no numerical dimensions provided Price information: not stated in product data Special features Coating: Tiger·tec Silver (coated cemented carbide) Material suitability: stainless steels (M), superalloys and titanium (S) Application focus: heavy‑duty machining of hard‑to‑machine alloys and stainless steels depending on geometry Benefit focus: heat resistance, stable cutting edge, controlled chip formation FAQ What materials is this insert intended for? The GX24-3E500N04-UD4 WSM33S insert is specified for stainless steels (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), where thermal resilience and edge stability are required. How does the Tiger·tec Silver coating help in machining? The Tiger·tec Silver coating provides improved heat resistance and wear performance on the insert, helping to maintain a stable cutting edge under elevated temperatures and reducing tool change frequency. What is the role of the 3E500N04‑UD4 chipbreaker? The 3E500N04‑UD4 geometry promotes reliable chip breaking and evacuation, which enhances surface finish and reduces the risks associated with long, tangled chips in turning operations. Can this insert be used for both roughing and finishing? Yes; depending on the chosen cutting parameters and holder setup, the coated WSM33S grade can be applied across roughing and finishing stages to balance productivity and surface quality. Where can application support or further data be obtained? Technical application support and supplementary machining data are available from Metav Werkzeuge; their advisors can help match the insert to the correct holder and process conditions. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Walter Tools is part of a leading family of precision tooling brands and is referenced here for descriptive purposes only. Protected trademarks and trade names remain the property of their respective owners. There is no affiliation between our company and the brand beyond the sale of original, factory‑new Walter Tools products.
GX24-3E500N04-UD6 WSM23S WSM23S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, a purpose-designed chipformer and proven edge stability to maintain high productivity when machining difficult-to-cut materials; order directly via Metav Werkzeuge or consult the team for application advice. GX24-3E500N04-UD6 WSM23S — Drehwendeschneidplatte (turning insert) with Tiger·tec Silver, for rostfreier Stahl and superalloys (Walter Tools) The GX24-3E500N04-UD6 WSM23S is a robust turning insert engineered for heavy-duty machining of rostfreier Stahl and heat‑resistant superalloys, offering a combination of thermal resistance and stable chip control suited to demanding turning operations. Tiger·tec Silver coating for edge stability Optimised chipformer 3E500N04-UD6 For rostfreier Stahl and superalloys Reliable life and consistent cutting results Maximum process reliability through advanced coating and grade The Tiger·tec Silver technology paired with the WSM23S grade provides a balanced, coated carbide that emphasises edge stability and thermal resistance. This combination reduces the risk of edge breakdown when machining tough materials such as rostfreier Stahl and nickel‑based alloys. The coated substrate supports secure cutting action and helps to maintain geometry tolerance over longer production runs, translating to fewer tool changes and higher overall throughput. Optimised chip control for safer, more productive turning The integrated chipformer 3E500N04-UD6 is designed to generate predictable chips and avoid entanglement in continuous cuts. Improved chip control lowers the likelihood of surface damage and reduces the need for manual intervention at the machine, which contributes to more consistent cycle times. When mounted in a matching toolholder, the insert delivers steady cutting behaviour, helping to protect the workpiece surface finish and the machine operator’s workflow. Application advice and benefits for workshop planning This insert is particularly suited to operations where material workhardening, poor thermal conductivity and severe tool stress are present. The grade’s properties favour applications requiring sustained cutting forces and elevated temperatures. In practice, users will see benefits in process stability and tool life when switching from a general‑purpose grade to WSM23S, especially on components with tight surface‑quality demands or long run lengths. Economic advantages and quality consistency in production By combining a modern coated carbide with a purpose‑matched geometry, the insert delivers a favourable balance between tool life and part quality. Reduced frequency of insert changes and improved repeatability in batch production contribute to lower unit costs and fewer interruptions. Choosing a proven machining grade from Walter Tools supports predictable performance and easier process documentation for quality control. Discuss the GX24-3E500N04-UD6 WSM23S Tiger·tec Silver insert with Metav Werkzeuge to define the optimal geometry and procurement solution for rostfreier Stahl and superalloy turning; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: GX24-3E500N04-UD6-WSM23S-WALTER Product type: Drehwendeschneidplatte Designation: GX24-3E500N04-UD6 WSM23S Series: Tiger·tec Silver Grade: WSM23S Core data Material group: S / M Suitable for: rostfreier Stahl (M), superalloys / titanium (S) Chipformer: 3E500N04-UD6 Special features Coating technology: Tiger·tec Silver Application: heavy machining of difficult‑to‑cut materials and, depending on geometry, rostfreier Stahl Manufacturer: Walter Tools Type: turning insert FAQ What materials is this insert intended for? The GX24-3E500N04-UD6 WSM23S insert is intended for machining rostfreier Stahl and heat‑resistant superalloys, where thermal resistance and edge stability are required. How does the Tiger·tec Silver coating improve performance? The Tiger·tec Silver coating on the WSM23S grade increases thermal resistance and supports stable edge behaviour, which helps to extend tool life in demanding turning operations. What is the role of the 3E500N04-UD6 chipformer? The chipformer 3E500N04-UD6 promotes predictable chip breakage and evacuation, enhancing surface finish consistency and reducing operator intervention during continuous cuts. Is this insert suitable for high‑volume production? Yes; the combination of coated carbide and optimised geometry offers consistent cutting performance and reduced insert changes, making it suitable for series production. Can the insert be used for finishing and roughing operations? Depending on the chosen geometry and cutting parameters, the grade can be employed for both roughing and finishing on difficult‑to‑cut materials, offering a balance between material removal rate and surface quality. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade designations are the property of their respective owners. Brand names and protected trade designations are mentioned solely for explanatory purposes. There is no relationship between our company and the named brands. The offered article is an original, brand‑new product of the manufacturer.
GX24-3E500N04-UD6 WSM33S WSM33S Wendeplatten - Walter Tools
Benefit from the Tiger·tec Silver coating and the WSM33S grade for secure chip control and a stable cutting edge in demanding turning applications; ideal for machining stainless steels and heat‑resistant superalloys. Order the insert directly via Metav Werkzeuge or consult the technical advisors if clarification is required. GX24-3E500N04-UD6 WSM33S — Indexable turning insert, Tiger·tec Silver, for stainless steels — Walter Tools The GX24-3E500N04-UD6 WSM33S is an indexable turning insert engineered for heavy‑duty machining of stainless steels and heat‑resistant superalloys, offering extended edge life through advanced coating technology. Tiger·tec Silver coating WSM33S coated carbide grade Optimised chip control geometry For stainless steels and superalloys High process reliability through advanced coating and grade The combination of Tiger·tec Silver and the WSM33S grade delivers a measurable advantage in environments with high temperatures and adhesion tendencies. The coating enhances heat resistance and reduces flank wear, while the substrate material—coated carbide—maintains a stable cutting edge under sustained load. For production contexts where consistency matters, this results in fewer tool changes and more predictable component quality, supporting throughput objectives and reducing unplanned downtime. Controlled chip formation for safer, faster machining The 3E500N04‑UD6 chipbreaker geometry promotes optimised chip control, converting long, stringy swarf into manageable segments and lowering the risk of built‑up edge formation common with stainless and superalloy materials. Good chip breaking reduces manual intervention at the machine, improves surface finish, and shortens cycle times. In practical terms, controlled chip behaviour helps maintain coolant flow and avoids interruptions that affect batch production and operator safety. Versatility and consistent performance in mixed production runs Designed for demanding materials, this indexable insert supports the economical machining of stainless steels and heat‑resistant superalloys, making it suitable for mixed production environments where material changeovers occur. The WSM33S grade balances edge robustness with reasonable wear resistance, enabling repeatable component tolerances and simplified tool inventory management. The GX24‑series geometry also ensures compatibility with common turning toolholders, aiding quick integration into existing tooling systems without complex adjustments. Contact Metav Werkzeuge for tailored selection advice on Walter Tools inserts and to discuss suitability for specific turning applications; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number / SKU: GX24-3E500N04-UD6-WSM33S-WALTER Designation: GX24-3E500N04-UD6 WSM33S Series: Tiger·tec Silver Grade: WSM33S Facts Coating: Tiger·tec Silver Substrate: Coated carbide Geometry: 3E500N04‑UD6 Special features Suitable for stainless steels (ISO group M) Suitable for heat‑resistant superalloys and titanium (ISO group S) Stable cutting edge and optimised chip control FAQ What materials is this indexable insert suitable for? The GX24‑3E500N04‑UD6 WSM33S insert is intended for stainless steels and heat‑resistant superalloys, reflecting the WSM33S grade’s focus on heat resistance and edge stability. How does the Tiger·tec Silver coating improve performance? The Tiger·tec Silver coating increases thermal resistance and reduces adhesive wear, which helps the insert retain a stable cutting edge during prolonged turning of demanding materials. Can the chipbreaker geometry handle long, stringy chips? Yes; the 3E500N04‑UD6 geometry promotes segmented chip formation, improving swarf control and reducing interruptions in the machining process. Is this insert compatible with standard turning toolholders? The GX24 series designation indicates compatibility with common indexable turning holders; the insert’s geometry allows straightforward integration into typical setups. What production benefits does the WSM33S grade offer? WSM33S delivers consistent tool life and reliable edge condition in demanding cuts, supporting higher process reliability and more predictable production planning. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Protected trademarks and trade names are the property of their respective owners. The Walter Tools brand is named for clarification and identification purposes only. There is no affiliation between our company and the named manufacturers; the offered item is original, factory‑new merchandise of Walter Tools.
GX24-3E500N04-UF4 WKP23S Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Silver grade and the WKP23S cutting material for consistent edge stability and efficient machining of steel and cast iron; order this insert via Metav Werkzeuge or contact the consultants for tailored cutting data. GX24-3E500N04-UF4 WKP23S indexable turning insert — Tiger‑tec Silver, for steel & cast iron | Walter Tools The GX24-3E500N04-UF4 WKP23S is an indexable turning insert engineered for productive turning of steel (P) and cast iron (K), offering a coated carbide grade optimised for stable chip formation and extended tool life Tiger‑tec Silver coating for durable edge Designed for steel and cast iron machining Stable chip formation and high process security Increased productivity through a resilient coating and grade The combination of the Tiger‑tec Silver coating and the WKP23S carbide grade delivers measurable gains in productivity by reducing flank wear and improving edge stability. The coating technology enhances wear resistance, which extends the tool life under typical steel and cast iron turning conditions. For production environments that prioritise uptime, the insert’s engineered surface reduces the frequency of index changes and supports longer uninterrupted runs while maintaining consistent component quality. Reliable chip control and consistent surface results Equipped with the specified chipbreaker geometry (3E500N04‑UF4), the insert promotes stable chip formation, lowering the risk of built-up edge and erratic chip shapes that can affect surface finish. The geometry is designed to manage the heat and chip flow characteristic of both unalloyed and alloyed steel as well as abrasive cast iron, which helps achieve reproducible workpiece surfaces and reduces secondary operations. This stability contributes directly to predictable cycle times and improved process security on turning centres. Application clarity for planning and tool selection The grade is classified for material groups P and K in accordance with ISO guidelines, indicating suitability for a broad range of steels and cast irons. The insert’s specifications are particularly useful for planners and machinists who require demonstrable material compatibility when setting cutting data. With its focus on a balance between edge robustness and coating performance, the insert supports operations that need a compromise between high material removal rates and surface quality, making it a versatile choice for mixed production shops. Simplified procurement and production integration As an indexable turning solution from Walter Tools’ Tiger‑tec Silver series, the insert integrates into standard turning tool holders that accept the GX24 geometry. The documented grade and chipbreaker designation support tool selection workflows and inventory management, enabling maintenance of consistent quality standards across multiple machines. The clear designation of the WKP23S sort simplifies reordering and ensures the same material characteristics are supplied for repeat jobs. Contact Metav Werkzeuge for application advice, cutting data recommendations and availability of Walter Tools Tiger‑tec Silver inserts to optimise the machining process for steel and cast iron Technical Data SKU: GX24-3E500N04-UF4-WKP23S-WALTER Article designation: GX24-3E500N04-UF4 WKP23S Series: Tiger‑tec Silver Grade: WKP23S Chipbreaker: 3E500N04-UF4 Material applicability: P / K Product type: Drehwendeschneidplatte Manufacturer: Walter Tools UID: GX24-3E500N04-UF4-WKP23S-WALTER Facts No dimensional data specified No cutting edge length provided No included insert thickness specified Special features Coating: Tiger‑tec Silver (coated carbide) Sort: WKP23S (coated cemented carbide) Main applications: Steel (P) and cast iron (K) Chip control: 3E500N04‑UF4 chipbreaker geometry Series characteristics: Optimised for edge stability and productive turning FAQ What materials is this insert suitable for? The GX24-3E500N04‑UF4 WKP23S indexable turning insert by Walter Tools is specified for machining steel (P) and cast iron (K) according to the grade classification, making it suitable for a wide range of steels and cast materials. What benefit does the Tiger‑tec Silver coating provide? The Tiger‑tec Silver coating on the WKP23S grade improves wear resistance and edge stability, which contributes to longer tool life and more consistent surface finish when using the Walter Tools insert. How does the chipbreaker designation affect performance? The 3E500N04‑UF4 chipbreaker is designed for stable chip formation in turning operations; this reduces the likelihood of irregular chips and supports reproducible surface quality with the GX24 insert. Can this insert be used on high‑volume turning centres? Yes — the combination of the coated WKP23S grade and the chipbreaker geometry supports process security and longer tool life, making it suitable for high‑volume production where consistent performance is required. How should this insert be specified when reordering? Order using the full designation GX24‑3E500N04‑UF4 WKP23S and reference Walter Tools to ensure the exact Tiger‑tec Silver grade and chipbreaker geometry are supplied. Manufacturer: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen; Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com Protected trademarks and trade names are the property of their respective owners. Brand names are used for explanatory purposes only and do not imply any affiliation with Metav Werkzeuge. The offered article is an original, brand‑new product from the manufacturer.
GX24-3E500N04-UF4 WSM23S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating, the WSM23S grade and the 3E500N04‑UF4 chipbreaker for secure chip control and long tool life in demanding stainless steel and superalloy turning operations; order directly via Metav Werkzeuge or consult our specialists for cutting‑parameter support. GX24-3E500N04-UF4 WSM23S indexable turning insert — Tiger‑tec Silver, for stainless steel and superalloys (Walter Tools) The GX24-3E500N04-UF4 WSM23S indexable turning insert is engineered to deliver heat‑resistant cutting performance and stable edge control for the machining of stainless steel and difficult superalloys. Tiger‑tec Silver coating for extended tool life WSM23S grade for stainless steel and superalloys 3E500N04‑UF4 chipbreaker for reliable chip control Stable cutting edge for productive machining High-performance cutting for demanding materials The combination of the Tiger‑tec Silver technology with the WSM23S coated‑carbide grade provides a tool concept optimised for materials that generate high heat and tend to form long or stringy chips. This indexable insert offers a stable cutting edge and enhanced wear resistance, which reduces the frequency of tool changes and supports more consistent cycle times. For users working within ISO group M (rostfreie Stähle / stainless steels) and S (heat‑resistant superalloys and titanium), the geometry and coating chemistry are selected to maintain a secure tool face and avoid built‑up edge formation. Precision chip control and process reliability The integrated 3E500N04‑UF4 chipbreaker is designed to shape chips consistently at typical turning feeds and depths for the intended material groups, improving evacuation and reducing risk of workpiece damage. This results in lower rework rates and a more reliable production flow. The insert’s design enables predictable cutting forces and surface finishes, which supports downstream processes and helps meet tolerances more consistently. For jobs where process security and repeatability matter, the combination of chip control and edge stability represents a concrete productivity gain. Practical advantages at the machine and on the shop floor Adopting this insert supports productive machining through longer edge life and reduced interruption for changeovers. The coated‑carbide construction reduces flank wear and extends usable life under elevated temperatures, while the chosen grade balances toughness and hardness for a broad application range. For technical clarification or assistance with parameter selection, Metav Werkzeuge provides application support: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 — practical advice is available for adapting feeds, speeds and coolant strategy to maximise performance. Contact Metav Werkzeuge for tailored cutting‑parameter recommendations and to secure Walter Tools Tiger‑tec Silver inserts for immediate production use Technical data Article number: GX24-3E500N04-UF4-WSM23S-WALTER Product designation: Drehwendeschneidplatte / indexable turning insert Series: Tiger‑tec Silver Grade: WSM23S Chipbreaker: 3E500N04‑UF4 Material suitability: S / M Facts No numerical specifications provided in the source data Special features Coated carbide grade (Tiger‑tec Silver) Designed for stainless steel and heat‑resistant superalloys Optimised chipformer for controlled chip breaking Stable cutting edge for productive machining Manufacturer brand: Walter Tools FAQ What materials is this insert suitable for? The GX24-3E500N04-UF4 WSM23S insert is suitable for stainless steel (ISO group M) and heat‑resistant superalloys or titanium (ISO group S), as indicated by the WSM23S grade and Tiger‑tec Silver technology. How does the 3E500N04‑UF4 chipbreaker influence performance? The 3E500N04‑UF4 chipbreaker delivers consistent chip control, improving evacuation and surface quality while reducing the chance of chip entanglement during turning with the Walter Tools insert. Is this insert intended for roughing or finishing? The coated‑carbide WSM23S grade and robust cutting edge make the insert versatile; depending on insert geometry and cutting parameters it can be used for productive roughing and stable finishing in demanding materials. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
GX24-3E500N04-UF4 WSM33S Wendeplatten - Walter Tools
Die Kombination aus der Tiger‑tec Silver‑Beschichtung, der WSM33S‑Sorte und der präzisen 3E500N04‑UF4 Spanformer‑Geometrie sorgt für sichere Spanbildung und stabile Schneidkanten bei der Bearbeitung von rostfreiem Stahl und hitzebeständigen Superlegierungen; bestellen über Metav Werkzeuge oder Rücksprache mit den technischen Beratern möglich GX24-3E500N04-UF4 WSM33S indexable turning insert — Tiger‑tec Silver, Walter Tools (for rostfreier Stahl & superalloys) The GX24-3E500N04-UF4 WSM33S is an indexable turning insert engineered for demanding turning operations on rostfreier Stahl and heat‑resistant superalloys, offering a coated cemented‑carbide substrate and a chipbreaker designed for reliable chip control Tiger‑tec Silver coating for enhanced wear resistance WSM33S grade optimised for rostfreier Stahl and superalloys 3E500N04‑UF4 chipbreaker for consistent chip formation Robust cutting edge stability for high process security Higher process security through a specialised grade and coating The combination of Tiger‑tec Silver coating and the WSM33S cemented‑carbide grade delivers measurable advantages when machining materials from ISO group M (rostfreier Stahl) and S (heat‑resistant superalloys, titanium). The coating increases thermal resistance and reduces adhesive wear, while the substrate maintains edge stability under cyclic load. This results in longer tool life and fewer unplanned tool changes, which supports continuous production and predictable batch processing. For users with limited metallurgical background, the key takeaway is that the coating plus grade pairing controls heat and prevents early edge breakdown, so cutting parameters remain stable over longer runs. Consistent chip control and better surface quality The dedicated 3E500N04‑UF4 chipbreaker geometry and the GX24 form factor optimise chip separation and evacuation, reducing the risk of built‑up edge and surface marring. Consistent chip formation lowers machining vibrations and helps to achieve an improved surface finish with fewer secondary operations. In practice, controlled chips also reduce machine downtime caused by chip congestion and make coolant strategies more effective. The insert’s geometry is therefore a direct contributor to both component quality and operational efficiency, especially in turning operations that demand repeatable finishes. Productivity gains through reduced tooling interventions As an indexable insert, the item enables fast turning‑insert indexing and straightforward replacement in compatible tool holders, minimising machine stoppages. The material and geometry choices emphasise a balance between edge toughness and thermal resistance, which is particularly beneficial for roughing and medium finishing in difficult‑to‑cut alloys. Fewer tool changes and stable cutting behaviour translate into lower unit production times and better overall equipment effectiveness. The clear economic effect is a higher throughput per tool life cycle while maintaining reproducible part quality. Contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for availability and technical advice on the GX24-3E500N04-UF4 WSM33S indexable turning insert by Walter Tools Technical data Article number: GX24-3E500N04-UF4-WSM33S-WALTER Designation: GX24-3E500N04-UF4 WSM33S Product type: Indexable turning insert Series: Tiger‑tec Silver Grade: WSM33S Chipbreaker: 3E500N04‑UF4 Applicable material groups: M, S (ISO 513) Facts Geometry designation: GX24 SKU: GX24-3E500N04-UF4-WSM33S-WALTER Substrate: coated cemented carbide Suitability: rostfreier Stahl true Special features Coating: Tiger‑tec Silver Purpose: machining of rostfreier Stahl and heat‑resistant superalloys/titanium Advantages: improved wear resistance, stable cutting edge, optimised chipformer Typical applications: demanding turning operations, roughing and medium finishing FAQ What materials is this insert designed for? The GX24-3E500N04-UF4 WSM33S insert is specified for rostfreier Stahl (ISO group M) and heat‑resistant superalloys and titanium (ISO group S), making it suitable for demanding turning tasks. How does the Tiger‑tec Silver coating benefit machining? The Tiger‑tec Silver coating on the WSM33S grade increases thermal stability and reduces adhesive wear, which maintains edge integrity and extends service life during high‑stress operations. Is the chip formation reliable for continuous production? Yes, the 3E500N04‑UF4 chipbreaker geometry provides consistent chip control, reducing chip congestion and contributing to stable production runs and improved surface quality. Can the insert be indexed on standard turning holders? The GX24 form factor and indexable design allow fast replacement and indexing in compatible turning tool holders to reduce machine downtime. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and protected product names are mentioned solely for explanation and reference. There is no affiliation between Metav Werkzeuge and the named brands. The offered item is an original, factory‑new product of the manufacturer Walter Tools.
GX24-3E500N04-UF4 WSM43S WSM43S Wendeplatten - Walter Tools
Take advantage of the combination of high thermal resistance, stable chip control and long tool life for reliable turning of demanding alloys; order this insert directly via Metav Werkzeuge or consult our specialists for application advice. GX24-3E500N04-UF4 WSM43S indexable turning insert – Tiger‑tec Silver, for stainless steels and superalloys (Walter Tools) GX24-3E500N04-UF4 WSM43S is an indexable turning insert engineered for heavy machining of heat‑resistant superalloys and for many stainless steels; ideal where stable cutting edges and controlled chip formation are essential Tiger-tec Silver coating technology WSM43S coated carbide grade Optimised chip control for tough alloys Designed for stainless steel and superalloys Reliable performance for demanding materials The Tiger‑tec Silver coating combined with the WSM43S carbide grade offers a balance of heat resistance and edge stability, specifically developed for hard‑to‑machine materials. Where heat accumulation and work‑hardening are common, this coated carbide grade supports consistent cutting behaviour and reduces the tendency for built‑up edge formation. For everyday production this means fewer interruptions for edge changes and improved process stability, especially when machining parts made from stainless steels and high‑temperature alloys. Productivity gains through stable chip formation With the integrated 3E500N04‑UF4 chipbreaker geometry, this insert promotes controlled chip evacuation and reduces rework time caused by erratic chips. Controlled chip formation leads to safer automatic machining and a more predictable tool life, which in turn improves cycle times and lowers overall unit costs. The design emphasises repeatable cutting conditions: predictable chips, consistent surface finish and extended cutting edge life — all contributing to measurable productivity improvements on the shop floor. Practical guidance for selection and application The grade is specified for ISO material groups M and S, meaning suitability for stainless steels (M) and heat‑resistant superalloys or titanium (S). In practice, tool performance depends on insert geometry, machine rigidity and cutting data; selecting the right geometry and feed/speed pairings will exploit the WSM43S strengths. For operators less familiar with ISO groupings: M = stainless steels prone to work hardening and heat build‑up; S = alloys that transfer heat poorly and demand thermal stability from the cutting edge. Using appropriate coolant strategies and stable clamping will further extend service life and ensure consistent results. Contact Metav Werkzeuge for tailored cutting data and rapid supply of the Walter Tools GX24-3E500N04-UF4 WSM43S insert — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: GX24-3E500N04-UF4-WSM43S-WALTER Article designation: GX24-3E500N04-UF4 WSM43S Product type: Drehwendeschneidplatte (indexable turning insert) Grade/series: WSM43S, Tiger‑tec Silver Facts Material groups: S / M Chipbreaker: 3E500N04‑UF4 Coating: Tiger‑tec Silver Special features Coated carbide grade WSM43S Optimised for heat resistance and edge stability Suitable for stainless steels and superalloys (ISO M, S) Stable chip control for automatic machining Manufacturer: Walter Tools FAQ Is this insert suitable for stainless steel turning? The GX24-3E500N04-UF4 WSM43S insert is suitable for many stainless steels (ISO group M); the WSM43S grade and Tiger‑tec Silver coating improve chip control and resist built‑up edge when appropriate cutting data are used. Can the insert be used on heat‑resistant superalloys and titanium? Yes. The insert is specified for ISO group S applications and the WSM43S grade provides thermal stability and a robust cutting edge for such materials. What is the function of the 3E500N04‑UF4 chipbreaker? The 3E500N04‑UF4 chipbreaker is designed to produce short, controllable chips during turning, improving evacuation and reducing the risk of entanglement in automatic operations. Is the Tiger‑tec Silver coating beneficial for interruptive cuts? The Tiger‑tec Silver coating enhances heat resistance and wear protection, which helps maintain edge integrity during interrupted or demanding cuts on difficult materials. Which features support long tool life in serial production? The combination of a coated carbide grade (WSM43S), a stable chipbreaker geometry and thermal resistance from the Tiger‑tec Silver coating contributes to prolonged cutting edge life and consistent performance in serial machining. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation only and do not imply any affiliation or endorsement by our company. The offered article is an original, factory‑new product from the manufacturer Walter Tools.
GX24-3E500N04-UF8 WSM23S WSM23S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, the WSM23S grade and a geometry optimised for secure chip control to maintain a stable production process; order the insert directly via Metav Werkzeuge or consult our specialists for application support. Drehwendeschneidplatte GX24-3E500N04-UF8 WSM23S – Turning indexable insert by Walter Tools, coated for heat resistance Drehwendeschneidplatte GX24-3E500N04-UF8 WSM23S is a coated turning insert intended for machining rostfreier Stahl and heat‑resistant superalloys, offering a balance of edge stability and wear resistance for demanding turning tasks Tiger·tec Silver coating for heat resistance WSM23S grade for tough materials Designed for rostfreier Stahl and superalloys Stable cutting edge for consistent finishes Longer tool life and consistent surface quality for high‑temperature materials The combination of the Tiger·tec Silver coating and the WSM23S coated‑carbide grade produces a cutting edge that resists thermal degradation, which directly translates into longer tool life and more consistent surface finish when machining difficult materials. In practice, this means fewer tool changes, reduced downtime and more predictable batch quality. The insert geometry 3E500N04‑UF8 supports controlled chip formation, reducing the tendency for built‑up edge when working with rostfreier Stahl or nickel‑based alloys. The result is a measurable improvement in process stability and part repeatability for serial production. Improved process security and reliable edge behaviour under load The technical design focuses on process security: the substrate and coating system are selected to withstand elevated temperatures and abrasive conditions typical of superalloy turning. The stable cutting edge prevents premature chipping and supports steady metal removal rates, contributing to fewer rejects and lower overall machining costs. For engineers and planners, this insert offers a predictable performance envelope that simplifies parameter setting and supports longer uninterrupted cycles on CNC lathes. Where surface integrity and dimensional consistency are critical, the insert’s behaviour under continuous load helps safeguard production targets. Practical advantages in workshop workflows and tool management As an indexable turning insert, the component reduces inventory complexity and improves tool management: limited toolholders can cover a range of operations thanks to the proven performance of the WSM23S grade. The coating’s heat resistance makes the insert suitable for higher cutting speeds in many applications, enabling faster cycle times without sacrificing edge life. For maintenance and toolroom teams, the insert’s repeatable performance eases process documentation and helps establish robust cutting data sheets. Should application adjustments be needed, in‑house technicians can rely on the insert’s consistent behaviour to fine‑tune feeds and speeds with confidence. Contact Metav Werkzeuge today to discuss application details for the GX24-3E500N04-UF8 WSM23S turning insert and secure tailored recommendations from our consultants Technical Data Article number: GX24-3E500N04-UF8-WSM23S-WALTER Product type: Turning indexable insert Series: Tiger·tec Silver Core data Grade: WSM23S Material groups: S / M ISO designation: GX24-3E500N04-UF8 WSM23S Special features Coating: Tiger·tec Silver (coated carbide) Application: rostfreier Stahl, heat‑resistant superalloys Cutting geometry: 3E500N04‑UF8 FAQ What workpiece materials is this insert suited for? The GX24‑3E500N04‑UF8 WSM23S insert is designed primarily for rostfreier Stahl and heat‑resistant superalloys (ISO groups S and M), offering stable chip control in these demanding materials. How does the Tiger·tec Silver coating affect performance? The Tiger·tec Silver coating on this Walter Tools insert improves thermal resistance and wear behaviour, which leads to more consistent edge life and enhanced process security during high‑temperature turning. Is this insert suitable for high cutting speeds? Yes, the coating and grade combination is intended to tolerate elevated cutting temperatures, allowing comparatively higher cutting speeds while maintaining reliable edge stability. What are the main benefits for production planning? The insert delivers fewer tool changes and predictable wear behaviour, supporting longer production runs and simplified cutting data documentation for leaner tool management. Can the insert be used in automated lathe cells? The repeatable performance and stable chip formation of the GX24‑3E500N04‑UF8 WSM23S make it a good choice for automated turning cells where consistency and process reliability are required. The Walter AG (brand: Walter Tools) with headquarters in Tübingen is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names are used solely for explanation; there is no affiliation between Metav Werkzeuge and the mentioned manufacturers.
GX24-3E500N08-UD4 WKP13S Wendeplatten - Walter Tools
Benefit from the combination of the Tiger‑tec Silver coating and the WKP13S grade for stable cutting performance and consistent chip control; the optimised 3E500N08‑UD4 chipbreaker supports efficient machining of steel and cast iron. Order the GX24‑3E500N08‑UD4 WKP13S turning indexable insert directly via Metav Werkzeuge or ask our consultants if needed. GX24-3E500N08-UD4 WKP13S turning indexable insert — Tiger‑tec Silver coating | Walter Tools The GX24-3E500N08-UD4 WKP13S is an indexable turning insert designed for precision machining of steel and cast iron, combining a robust coated‑carbide grade with a dedicated chipbreaker for reliable production. Tiger‑tec Silver coating for long tool life Optimised chipbreaker 3E500N08-UD4 Suitable for steel (P) and cast iron (K) Coated carbide grade WKP13S for stability Enhanced process reliability through coating and grade The combination of the Tiger‑tec Silver coating with the WKP13S grade provides a measurable increase in wear resistance and consistent edge behaviour under typical turning conditions. The coated‑carbide construction reduces flank and crater wear, which translates into longer intervals between index changes and fewer unscheduled tool changes on the shop floor. As a result, cycle times remain stable and the cutting edge maintains performance across repetitive batches, supporting a predictable production rhythm and lower overall tooling costs. Predictable chip control and material compatibility The insert's 3E500N08‑UD4 chipbreaker geometry is engineered to produce short, controllable chips when machining both steel (ISO group P) and cast iron (ISO group K). In practice this means reduced risk of chip entanglement, safer handling at higher feeds and easier chip evacuation from the cutting zone. For readers unfamiliar with the ISO codes: P denotes steels (unalloyed and alloyed) and K denotes cast iron; the grade and geometry are matched to the thermal and abrasive behaviour typical of these groups. This targeted design improves the surface finish and reduces the need for secondary operations caused by erratic chip formation. Integrating the insert for greater productivity Adopting this insert supports a leaner turning process by combining process reliability with simple inventory management: the WKP13S grade fits a broad range of steel and cast‑iron applications and the standardised insert designation aids tool planning. Fewer index changes and consistent cutting behaviour shorten machine downtime and contribute to higher net throughput. For production planners the key benefit is a stable machining window that allows for repeatable setups and dependable tool‑life forecasting, which in turn simplifies cost‑per‑part calculations and enhances capacity planning. For high‑performance turning with Walter Tools reliability, contact Metav Werkzeuge for tailored advice and fast supply of the GX24-3E500N08-UD4 WKP13S insert — info@metav-werkzeuge.com • +49 2822 7131930 Technical data Article number: GX24-3E500N08-UD4-WKP13S-WALTER Type: Turning indexable insert Designation: GX24-3E500N08-UD4 WKP13S Brand: Walter Tools Facts Material/application: P / K Suitable for: Steel (P) Suitable for: Cast iron (K) Series: Tiger‑tec Silver Special features Grade: WKP13S (coated carbide) Chipbreaker: 3E500N08-UD4 Main application: precision turning with stable chip control FAQ What materials is this insert suitable for? The GX24‑3E500N08‑UD4 WKP13S insert is intended for steel (ISO group P) and cast iron (ISO group K), reflecting the design goals of the WKP13S grade and the Tiger‑tec Silver coating. How does the Tiger‑tec Silver coating benefit tool life? The Tiger‑tec Silver coating on the WKP13S grade reduces abrasive and thermal wear, so the insert keeps its cutting edge longer and delivers more consistent performance across production runs. What is the role of the 3E500N08‑UD4 chipbreaker? The 3E500N08‑UD4 chipbreaker shapes and breaks the chips into short, controllable segments during turning of steel and cast iron, improving chip evacuation and surface quality while lowering handling risks. Is this insert suitable for high‑feed turning operations? The combination of the WKP13S grade and the chipbreaker geometry offers robust performance across a range of feeds; specific feed and speed recommendations depend on workpiece material and machine rigidity. Can the GX24‑3E500N08‑UD4 be used for finishing passes? Yes — the insert provides stable cutting behaviour that supports predictable surface finishes; final pass parameters should be selected according to the required surface quality and dimensional tolerances. Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation only and do not imply any affiliation between our company and the named brands. The offered item is an original factory‑new product of the manufacturer Walter Tools. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
GX24-3E500N08-UD4 WKP23S Wendeschneidplatte - Walter Tools
Take advantage of high wear resistance and controlled chip formation combined with broad applicability for steel and cast iron machining — an efficient choice for stable turning processes; order directly via Metav Werkzeuge or consult the team for application-specific cutting data. GX24-3E500N08-UD4 WKP23S — indexable turning insert for steel and cast iron by Walter Tools, Tiger·tec Silver coated A GX24-3E500N08-UD4 WKP23S indexable turning insert engineered for robust general turning of steel (P) and cast iron (K), offering a coated cemented carbide grade for consistent removal rates. Tiger·tec Silver coating for wear resistance WKP23S coated carbide grade Optimised 3E500N08-UD4 chipbreaker For machining steel and cast iron Extended tool life through advanced coating technology The Tiger·tec Silver coating together with the WKP23S grade results in superior wear resistance and more predictable flank wear progression. As a coated cemented carbide insert, it tolerates the thermal and mechanical loads typical of steel turning, which reduces the frequency of insert changes and supports continuous production. The metallurgical design of the grade is tailored for stable cutting-edge performance, translating into lower overall tooling costs and fewer interruptions in the machining cycle. Reliable chip control for improved surface quality Equipped with the 3E500N08-UD4 chipbreaker geometry, this insert promotes controlled chip formation and evacuation during turning operations. Stable chip behaviour minimises the risk of built-up edge and unexpected surface defects, improving first-pass yield and reducing downstream rework. The optimised chip pocket and edge preparation contribute directly to a consistent surface finish and predictable tool life, which is critical for serial production environments seeking repeatable results. Broad material range for flexible process planning Designed for ISO material groups P (steel) and K (cast iron), the insert supports a wide variety of common turning tasks without compromising edge stability. The combination of the WKP23S grade and the Tiger·tec Silver technology balances abrasion resistance and toughness, enabling effective machining of unalloyed steels, alloyed steels and many cast-iron variants. This versatility simplifies tooling inventories and allows for flexible job planning across mixed-production shops. Process security and productivity gains Integrating this insert into standard indexable turning systems enhances process reliability through repeatable edge behaviour and dependable chip control. The product’s geometry and grade focus on delivering consistent machining results, reducing unexpected stoppages and promoting higher effective machine utilisation. For manufacturers seeking measurable productivity improvements, the technical design enables smoother cycle times and supports stable, long-term performance in demanding turning applications. Contact Metav Werkzeuge for tailored cutting data and application advice on Walter Tools Tiger·tec Silver inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss compatibility and optimisation for specific turning tasks Technical Data Article number: GX24-3E500N08-UD4-WKP23S-WALTER Label: GX24-3E500N08-UD4 WKP23S turning insert Manufacturer: Walter Tools Product type: Indexable turning insert Core specifications Grade: WKP23S Series: Tiger·tec Silver Material suitability: P / K (steel, cast iron) Chipbreaker: 3E500N08-UD4 Special features Coated cemented carbide Optimised chip control Suitable for general turning applications UID: GX24-3E500N08-UD4-WKP23S-WALTER FAQ Is this insert suitable for both steel and cast iron? The GX24-3E500N08-UD4 WKP23S insert is specified for ISO groups P and K, making it suitable for a wide range of steel and cast-iron turning tasks. What advantages does the Tiger·tec Silver coating provide? Tiger·tec Silver on the WKP23S grade offers enhanced wear resistance and thermal stability, which helps the GX24-3E500N08-UD4 insert maintain edge integrity over longer cycles. How does the 3E500N08-UD4 chipbreaker affect machining? The 3E500N08-UD4 chipbreaker is optimised for controlled chip formation and evacuation, improving surface finish consistency and reducing the risk of chip-related interruptions when using this Walter Tools insert. Can the insert be used in standard turning toolholders? The GX24-3E500N08-UD4 WKP23S is designed for common indexable turning systems; matching the insert seat and clamp style to the toolholder is recommended for secure seating and accurate results. What production benefits can be expected from using this grade? Using the WKP23S grade with Tiger·tec Silver typically results in fewer tool changes, more predictable wear, and improved machine uptime, contributing to a stable, cost-efficient production flow. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Registered trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered item is an original, brand‑new product of the manufacturer.
GX24-3E500N08-UD4 WKP33S WKP33S Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Silver coating and the WKP33S grade together with the 3E500N08‑UD4 chipbreaker to increase process security and tool life in turning operations on steel and cast iron; order directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. GX24-3E500N08-UD4 WKP33S – turning insert, Tiger‑tec Silver coating, for steel and cast iron | Walter Tools The GX24-3E500N08-UD4 WKP33S is a coated indexable turning insert engineered for productive external turning of steel and cast iron, combining a specialised chipbreaker geometry with a wear-resistant Tiger‑tec Silver grade. Tiger‑tec Silver coating for longer tool life WKP33S grade optimised for steel and cast iron 3E500N08‑UD4 chipbreaker for controlled chips Compatible with standard turning tool holders Proven performance for steel and cast iron machining The coated carbide grade delivers a stable balance between wear resistance and toughness. Designed for the typical heat and chip formation when machining steel, and optimised for the abrasive, short‑breaking chips of cast iron, the grade supports consistent cutting conditions. The combination of Tiger‑tec Silver coating and the WKP33S composition reduces flank and crater wear, which translates into longer intervals between insert changes and higher throughput on production lines. Controlled chip formation and process security The dedicated 3E500N08‑UD4 chipbreaker geometry provides reliable chip control across a range of cutting parameters. By producing predictable, controllable chips, the insert lowers the risk of workpiece damage and tool holder interruptions, improving machine uptime. The engineered chip shape also simplifies swarf handling and reduces manual interventions, contributing to a safer and more efficient machining environment. Easy integration and consistent results Manufactured for use in established tool holder systems, this indexable insert fits typical turning fixtures and supports quick insert index changes. The combination of coating, grade and chipbreaker aims to deliver repeatable surface quality and dimensional stability, which benefits batch production and repeat jobs. Together these attributes support a measurable productivity improvement and a robust, economical machining process. For application advice or to specify the correct insert geometry for a particular turning task, contact Metav Werkzeuge — our experts provide technical support and delivery information for Walter Tools products. Technical data Article number: GX24-3E500N08-UD4-WKP33S-WALTER SKU: GX24-3E500N08-UD4-WKP33S-WALTER Product type: Turning insert (indexable) Brand: Walter Tools Facts Series: Tiger‑tec Silver Grade / Sort: WKP33S Chipbreaker: 3E500N08‑UD4 Material groups: P / K (steel / cast iron) Special features Coated carbide grade Optimised for steel and cast iron machining Designed for controlled chip formation Compatible with standard turning tool holders FAQ What materials is this insert suitable for? The GX24-3E500N08-UD4 WKP33S insert is formulated for steel (P) and cast iron (K) applications, offering tailored wear behaviour for both groups. How does the Tiger‑tec Silver coating benefit production? The Tiger‑tec Silver coating on this Walter Tools turning insert improves wear resistance and thermal stability, extending tool life under typical turning conditions. Does the chipbreaker suit roughing and finishing operations? The 3E500N08‑UD4 chipbreaker is optimised for controlled chips during a range of cutting depths and feeds, making it suitable for many roughing and semi‑finishing scenarios. Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation and identification purposes; no affiliation with the named manufacturers is implied. The offered article is original, factory‑new merchandise from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen
GX24-3E500N08-UD4 WSM33S WSM33S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and an optimised 3E500N08-UD4 chipbreaker for reliable chip control and extended tool life; order the insert directly via Metav Werkzeuge or request application advice from the consultants at Metav. GX24-3E500N08-UD4 WSM33S Drehwendeschneidplatte — Tiger·tec Silver coating, for rostfreier Stahl & superalloys (Walter Tools) The GX24-3E500N08-UD4 WSM33S is a turning insert engineered for stable performance when machining rostfreier Stahl and heat-resistant superalloys, combining a coated carbide grade with a dedicated chipbreaker for predictable results. Tiger·tec Silver coating for improved wear resistance Optimised 3E500N08-UD4 chipbreaker for stable chips Designed for rostfreier Stahl and heat-resistant alloys Robust cutting edge for extended tool life Enhanced wear resistance for demanding materials The WSM33S grade from the Tiger·tec Silver family is a coated carbide designed to resist thermal and abrasive wear during interrupted or continuous turning of demanding alloys. The specialised coating delivers a balanced hardness and toughness combination, which supports secure chip control and reduces the tendency for built-up edge when processing rostfreier Stahl. This results in longer index intervals and fewer tool changes, improving overall process efficiency. Predictable chip formation and surface quality The integrated chipbreaker 3E500N08-UD4 was developed to control chip shape and evacuation under moderate to heavy cutting conditions. A stable chipflow reduces machine downtime caused by entanglement and simplifies swarf handling. The consequence is a more consistent surface finish and reduced rework. For operations where surface integrity and repeatability are critical, the insert’s geometry contributes directly to cycle-time reductions and improved component conformity. Robust cutting edge for higher productivity A mechanically strong cutting edge and the thermal resilience of the grade contribute to long tool life and steady cutting performance. The insert’s construction supports higher metal-removal rates in appropriate setups while maintaining edge stability, which benefits throughput and lowers tooling costs per part. The combination of edge robustness and coating technology promotes predictable wear behaviour across batch and serial production runs. Practical notes for application and handling This turning grade is compatible with standard indexable insert toolholders designed for the respective geometry family. While the insert excels on rostfreier Stahl and superalloys, adhesion-prone materials require suitable cutting fluids and adjusted feeds to avoid built-up edge. Inserts from this series can be used in roughing and finishing passes depending on the chosen cutting parameters and machine capability. For specific holder recommendations or cutting-data windows, consult the technical advisors at Metav Werkzeuge or the Walter Tools documentation. For machining rostfreier Stahl and heat-resistant alloys with confidence, contact Metav Werkzeuge for ordering and tailored application support — eMail info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: GX24-3E500N08-UD4-WSM33S-WALTER Type: Drehwendeschneidplatte Grade: WSM33S Series: Tiger-tec Silver Chipbreaker: 3E500N08-UD4 Facts Material groups: S / M Suitable for rostfreier Stahl: yes SKU / UID: GX24-3E500N08-UD4-WSM33S-WALTER Special features Coated carbide grade Application: rostfreier Stahl (M), heat-resistant superalloys and titanium (S) Designed for stable chip formation and long tool life Manufacturer: Walter Tools FAQ Is this insert suitable for machining stainless steels? Yes. The GX24-3E500N08-UD4 WSM33S insert is specified for rostfreier Stahl and provides balanced wear resistance and edge stability for those materials. What is the benefit of the Tiger·tec Silver coating? The Tiger·tec Silver coating on the WSM33S grade increases thermal and abrasive wear resistance, which extends insert life and supports consistent performance in demanding turning tasks. Which chipbreaker should be chosen for heavy roughing? The integrated 3E500N08-UD4 chipbreaker on this insert is optimised for stable chip control under more aggressive cuts; selection should be confirmed against the workpiece material and machine rigidity. Can this insert be used for titanium alloys? The insert’s grade is designed for heat-resistant materials; it can machine titanium and similar superalloys when feeds, speeds and cooling strategies are adjusted accordingly. How does the insert impact overall productivity? By providing a robust cutting edge and controlled chip formation, the insert reduces index frequency and improves cycle repeatability, contributing to measurable productivity gains in series production. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik-Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
GX24-3E500N08-UF4 WKP23S Wendeplatten - Walter Tools
Die Kombination aus Tiger·tec Silver-Beschichtung und der Sortenwahl WKP23S sorgt für konstante Spanbildung und hohe Verschleißfestigkeit – ideal für produktive Drehprozesse in Stahl und Gusseisen. Bestellen über Metav Werkzeuge oder Beratung anfordern für die passende Einsatzempfehlung. GX24-3E500N08-UF4 WKP23S — Turning insert, Tiger·tec Silver, for Stahl & Gusseisen · Walter Tools A GX24-3E500N08-UF4 WKP23S indexable turning insert designed for high-performance turning of Stahl and Gusseisen in industrial CNC operations. Tiger·tec Silver coating for extended tool life WKP23S grade for Stahl and Gusseisen Stable chip formation and wear resistance Precision GX24 geometry for reliable performance Extended tool life through Tiger·tec Silver coating The Tiger·tec Silver coating combines thermal stability with a wear-resistant surface treatment to reduce adhesion and flank wear during continuous turning cycles. This coating technology is particularly effective when machining Stahl under elevated cutting temperatures, as it slows edge degradation and maintains dimensional stability over longer runs. Fewer tool changes mean lower downtime and improved component throughput, which supports predictable cycle times in series production. Optimised geometry and chip control for consistent surfaces The GX24 insert geometry together with the 3E500N08-UF4 chipbreaker and the WKP23S grade promotes stable chip formation, preventing irregular breakage and pile-up. Stable chip control improves surface quality and reduces the need for rework, so finishing operations remain minimal. For shops focused on repeatability, this combination delivers uniform results across batches while simplifying the choice of cutting parameters for turning operations. Higher productivity through process security and wear resistance By pairing a coated carbide grade with an engineered chipbreaker, the insert enhances process security and overall productivity: longer tool life, fewer interventions at the machine and steady performance under varying cutting conditions. The design is suited to continuous production where predictable tool behaviour is essential. The result is measurable efficiency gains and a reduction in unexpected stoppages during medium- to high-volume turning. Simple integration and practical application guidance As an indexable turning insert, the component fits standard toolholders compatible with the GX24 form; mechanical clamping and seat geometry remain industry standard, enabling straightforward replacement in existing tool systems. For optimal results, cutting data should be adapted to workpiece material and operation type; Metav Werkzeuge provides application support and recommended parameters to match material classes P and K. Practical guidance helps bridge the gap between specification and shop-floor performance. Contact Metav Werkzeuge for tailored cutting data and application advice on Walter Tools GX24-3E500N08-UF4 WKP23S inserts — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: GX24-3E500N08-UF4-WKP23S-WALTER Label: Drehwendeschneidplatte GX24-3E500N08-UF4 WKP23S Walter Tools Product type: Turning insert / indexable insert Series: Tiger·tec Silver Grade: WKP23S Geometry: GX24-3E500N08-UF4 Facts Applicable material groups: P (Stahl) Applicable material groups: K (Gusseisen) Material class (insert): Coated carbide Chipbreaker: 3E500N08-UF4 Special features Coating technology: Tiger·tec Silver Stable chip formation and wear resistance Designed for industrial CNC turning Manufacturer: Walter Tools FAQ Which workpiece materials are best suited to this insert? The GX24-3E500N08-UF4 WKP23S insert is optimised for Stahl (group P) and Gusseisen (group K), providing robust performance across common steel and cast-iron turning applications. What benefits does the Tiger·tec Silver coating provide? Tiger·tec Silver on the WKP23S grade reduces flank and crater wear, improving tool life and maintaining consistent cutting edge performance for the Walter Tools insert in demanding turning operations. Is the chipbreaker suitable for heavy roughing or finishing passes? The 3E500N08-UF4 chipbreaker is tuned for controlled chip formation; its profile supports stable chips during roughing and can be used to achieve good surface quality in many finishing scenarios depending on selected cutting data. Can this insert be used in existing GX24 toolholders? Yes, the insert is manufactured to the GX24 form and will fit standard toolholders designed for that geometry; confirm clamping compatibility and contact Metav Werkzeuge for any special holder requirements. How does this insert improve process reliability in production? By combining a coated carbide grade with a dedicated chipbreaker and robust geometry, the insert offers process security, fewer unexpected tool changes and consistent component quality across production batches. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only and do not indicate any affiliation with our company. The offered item is an original, factory-new product of the manufacturer Walter Tools.
GX24-3E500N08-UF4 WSM33S WSM33S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the WSM33S grade to secure stable chip formation and prolonged edge life in demanding stainless and heat‑resistant alloy turning operations; order directly via Metav Werkzeuge or consult our technical team for application support. GX24-3E500N08-UF4 WSM33S turning insert — coated carbide for stainless steels and superalloys, Walter Tools The GX24-3E500N08-UF4 WSM33S is a coated indexable turning insert engineered for heavy‑duty machining of rostfreier Stahl and heat‑resistant superalloys, offering stable cutting edges and reliable chip control in industrial turning applications. Tiger·tec Silver coating for high thermal stability Optimised chipbreaker 3E500N08-UF4 for reliable chips Ideal for stainless steels and superalloys Consistent edge life for productive turning Maximise process reliability with a thermally resilient coating The combination of the Tiger·tec Silver technology and the WSM33S cemented carbide grade provides elevated thermal resistance and wear stability. This results in a reduced tendency to build up material on the cutting edge when machining stainless steels and high‑temperature alloys. The coating architecture improves heat management at the cutting zone, which in turn supports consistent edge life and reduces unplanned tool changes. For production environments where predictable tool performance is essential, the coating‑substrate pairing contributes directly to increased machine uptime and repeatable component quality. Predictable chip control through a dedicated chipbreaker geometry The 3E500N08‑UF4 chipbreaker geometry is optimised for secure chip formation in tough‑to‑cut materials. The geometry promotes short, segmented chips and prevents long, stringy swarf that can interrupt productivity or damage workpiece surfaces. In practical terms, the chip design reduces the need for secondary chip handling equipment and supports safer, cleaner machining cycles. Clear advantages include fewer stoppages for chip removal and improved surface finish stability, which together enhance throughput and lower manufacturing variability. Suited materials and ISO classifications explained This insert is formulated for ISO groups M and S — namely stainless steels (M) and heat‑resistant superalloys and titanium (S). Materials in these families typically generate high temperatures at the cutting edge and demand both thermal stability and robust edge integrity. The WSM33S grade balances hardness and toughness to resist crater wear and chipping under those conditions. For users less familiar with metallurgical terms: a grade that resists high temperatures helps maintain a sharp, intact cutting edge for longer, which translates to fewer tool changes and more consistent part tolerances. Productivity gains and application scenarios in production Integrated into a turning toolholder system, this indexable plate supports medium to heavy roughing and finishing passes on components such as shafts, flanges and housings made from rostfreier Stahl and nickel‑based alloys. The insert’s stable edge life and controlled chip flow make it suitable for shops focused on repeatability and high output. By using a tool grade tuned to the workpiece family and a chipbreaker matched to the machining strategy, manufacturers can expect measurable improvements in cycle time and surface quality, which contribute directly to cost‑efficiency and customer satisfaction. For machining challenging stainless steels and superalloys, select Walter Tools inserts through Metav Werkzeuge — contact our application specialists at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss specific requirements and material pairings Technical Data Article number: GX24-3E500N08-UF4-WSM33S-WALTER Designation: GX24-3E500N08-UF4 WSM33S Product type: Turning insert (indexable) Facts Series: Tiger·tec Silver Grade: WSM33S (coated carbide) Chipbreaker: 3E500N08‑UF4 Material groups: S / M Special features Coated cemented carbide for enhanced thermal resistance Suitable for rostfreier Stahl and heat‑resistant superalloys/titan Optimised chip control for secure swarf formation Stable cutting edge for productive turning FAQ What materials is this insert intended for? The GX24‑3E500N08‑UF4 WSM33S insert is designed primarily for stainless steels (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), providing thermal stability and edge robustness for these demanding materials. How does the Tiger·tec Silver coating benefit machining? The Tiger·tec Silver coating increases heat resistance and reduces wear at the cutting edge, so the WSM33S grade maintains consistent edge life and supports prolonged tool performance in high‑temperature cutting conditions. Which chipbreaker is used and why does it matter? The insert employs the 3E500N08‑UF4 chipbreaker, which promotes short, controllable chips suitable for automated and manual turning operations, enhancing safety, surface finish and process reliability. Is this insert suitable for both roughing and finishing? Yes; thanks to the balance of toughness and wear resistance in the WSM33S grade, the plate can be used for medium to heavy roughing and for finishing passes when the machining parameters and toolholder setup are optimised. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Walter Tools ist ein Anbieter renommierter Präzisionswerkzeuge mit hoher Prozesssicherheit, präziser Bearbeitung und stabiler Schneidkante.
GX24-3E500N08-UF8 WSM23S WSM23S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, the WSM23S grade and an optimised chipformer for secure machining of challenging alloys; order the insert directly via Metav Werkzeuge or consult our advisors for application-specific recommendations. GX24-3E500N08-UF8 WSM23S — Indexable turning insert, Tiger·tec Silver (Walter Tools) A GX24-3E500N08-UF8 WSM23S indexable turning insert engineered for heavy-duty turning of rostfreier Stahl and high-temperature superalloys, offering a balance of edge stability and controlled chip formation for demanding production environments Tiger·tec Silver coating for heat resistance WSM23S grade for tough alloys Optimised chip control with 3E500N08-UF8 Stable cutting edge for long tool life High-temperature stability that keeps production running The combination of the Tiger·tec Silver technology and a coated carbide substrate gives this insert superior heat resistance and an improved resistance to abrasive wear. For components made from rostfreier Stahl and nickel-based superalloys, these properties reduce thermal loading on the cutting edge and slow flank wear, which directly translates into longer tool life and fewer interruptions on the machine. Operators and planning engineers benefit from fewer tool changes and a more predictable process window when working with heat-prone materials. Reliable chip formation and dimensional consistency The integrated chip control geometry, coded as 3E500N08-UF8, is designed to break and evacuate chips reliably during turning operations of tough materials. Controlled chip flow reduces the risk of recutting, surface damage and unexpected tool stress, enabling a consistent surface finish and repeatable dimensions on each workpiece. The grade WSM23S supports a stable cutting edge under high temperatures, which helps maintain tolerance chains and reduces rework rates in serial production. Practical selection guidance for workshop use Selection should consider workpiece material and cutting strategy: the WSM23S grade is particularly suited to rostfreier Stahl and heat-resistant superalloys where thermal and adhesive wear dominate. Choose the GX24-3E500N08-UF8 variant when reliable chipbreaking and edge strength are priorities. For integration, pair the insert with a compatible turning holder that secures the seat and supports positive clamping to exploit the stable cutting edge and to maximise productivity in both roughing and semi-finishing cycles. Contact Metav Werkzeuge for tailored application advice or to request a quote for the Walter Tools GX24-3E500N08-UF8 WSM23S insert; our consultants assist with grade selection and cutting data optimisation Technical data SKU: GX24-3E500N08-UF8-WSM23S-WALTER Product type: Indexable turning insert Grade: WSM23S Series: Tiger·tec Silver Geometry / chipbreaker: 3E500N08-UF8 Manufacturer: Walter Tools Core data Material designation: S / M Insert designation: GX24-3E500N08-UF8 WSM23S Wendeplatte ISO designation: GX24-3E500N08-UF8 WSM23S Special features Coated carbide sort (Tiger·tec Silver) Intended for rostfreier Stahl and superalloys (ISO groups M and S) Designed for stable chip formation and edge retention Optimised for heavy-duty turning applications FAQ Is this insert suitable for machining rostfreier Stahl? Yes. The WSM23S grade and Tiger·tec Silver coating of the GX24-3E500N08-UF8 WSM23S insert are specifically designed to address the thermal and adhesive tendencies of rostfreier Stahl, supporting stable cutting and extended tool life. Which workpiece materials match the insert’s capabilities? The insert performs best on rostfreier Stahl and high-temperature superalloys (ISO groups M and S); the combination of coating and grade is tuned to maintain cutting-edge integrity under elevated temperatures. How does the 3E500N08-UF8 chipbreaker improve production? The 3E500N08-UF8 chipbreaker provides consistent chip segmentation and evacuation, reducing recutting and surface damage, which leads to fewer interruptions and more repeatable component quality when turning tough materials. Can the insert be used for both roughing and finishing? Depending on cutting data and holder rigidity, the GX24-3E500N08-UF8 WSM23S insert can be applied in roughing and semi-finishing operations where edge stability and controlled chip formation are required; adjustments to feed and depth of cut will determine the optimal use. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik‑Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
GX24-3E500N25-RD4 WKP23S WKP23S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the WKP23S grade for extended tool life and stable edge performance; the optimised 3E500N25-RD4 chipformer ensures reliable chip control and fewer interruptions in turning operations. Order the inserts directly via Metav Werkzeuge or consult their specialists for application advice. GX24-3E500N25-RD4 WKP23S turning insert — Tiger·tec Silver for steel & cast iron (Walter Tools) The GX24-3E500N25-RD4 WKP23S is a robust turning insert engineered for efficient chip control and high process security in the turning of steel and cast iron. Tiger·tec Silver coating for extended tool life WKP23S coated carbide for robust cutting edges Optimised 3E500N25-RD4 chipformer for reliable chips Suited for steel and cast iron ISO P and K Boosted lifetime and consistent cutting performance The insert’s Tiger·tec Silver coating and WKP23S grade combine to deliver increased wear resistance and consistent cutting behaviour under industrial turning conditions. The coated carbide composition minimises flank and crater wear, resulting in fewer tool changes and more predictable component quality. For production planners this translates directly into higher machine uptime and reduced tooling costs, since edge degradation is delayed without sacrificing dimensional stability. Better chip control, fewer interruptions The integrated 3E500N25-RD4 chipformer is designed to shape chips reliably during roughing and finishing, reducing the risk of stringing and tool-clogging. Improved edge stability ensures each indexed position maintains cutting integrity over repeated uses; this means shorter cycle interruptions for chip clearing and a smoother workflow on shop-floor lathes. Operators with varied batch sizes will find less rework and safer running conditions when chips are predictable. Clear suitability for ISO P and K materials This insert is optimised for machining applications within ISO P (steel) and ISO K (cast iron). For non-specialists: ISO P designates tools tuned to handle the heat and continuous chips typical of steels, while ISO K indicates resistance to abrasive wear and short, brittle chips from cast iron. The combination of coating and geometry allows one grade to cover a broad range of turning tasks across these workpiece groups, simplifying tooling logistics and stocking. Practical advantages for production workflows Adopting inserts with this specification supports reproducible part quality and streamlined tool management. The reliable coated grade and chip control reduce setup tweaks and inspection cycles, enhancing overall productivity. In addition, the geometrical stability of the insert reduces scatter in surface finish and dimensional tolerance, which benefits downstream processes and lowers scrap rates in continuous manufacturing environments. For production-critical turning needs, contact Metav Werkzeuge to discuss the GX24-3E500N25-RD4 WKP23S inserts and secure tailored recommendations; email info@metav-werkzeuge.com or call +49 2822 7131930 to arrange immediate supply or technical consultation Technical Data SKU: GX24-3E500N25-RD4-WKP23S-WALTER Product name: Drehwendeschneidplatte GX24-3E500N25-RD4 WKP23S Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WKP23S Facts Chipformer: 3E500N25-RD4 Material designation: P / K UID: GX24-3E500N25-RD4-WKP23S-WALTER Article code: GX24-3E500N25-RD4 Special features Coating technology: Tiger·tec Silver Cutting material: coated carbide (WKP23S) Application groups: steel (ISO P), cast iron (ISO K) Geometry optimised for reproducible chip breaking FAQ What materials is this insert designed for? The GX24-3E500N25-RD4 WKP23S turning insert from Walter Tools is designed for steel (ISO P) and cast iron (ISO K) machining applications. How does the Tiger·tec Silver coating help in production? The Tiger·tec Silver coating increases wear resistance and thermal stability, which extends insert life and maintains cutting performance under continuous operation. What benefit does the 3E500N25-RD4 chipformer provide? The 3E500N25-RD4 chipformer promotes reliable chip formation and evacuation, reducing stoppages for chip clearing and improving cycle regularity. Can this insert reduce tooling costs in a production environment? Yes, the combination of WKP23S grade and advanced coating leads to longer tool life and fewer changes, which reduces tooling consumption and associated downtime. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only; there is no affiliation between our company and the named manufacturers. The offered article is original and brand-new. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
GX24-3E500N25-RD4 WSM33S WSM33S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and an optimised chipbreaker for reliable machining of demanding alloys; order originals via Metav Werkzeuge or consult the team for process-matching advice. GX24-3E500N25-RD4 WSM33S indexable turning insert — Tiger·tec Silver, 3E500N25-RD4 chipbreaker (Walter Tools) The GX24-3E500N25-RD4 WSM33S is an indexable turning insert engineered for heavy-duty turning in hard-to-machine alloys and rostfreier Stahl, combining a wear-resistant coated carbide grade with a dedicated chip control geometry. Tiger·tec Silver coating for heat resistance Optimised chipbreaker 3E500N25-RD4 Suited for rostfreier Stahl and superalloys Walter Tools manufacturing consistency Consistent chip control to reduce downtime The insert’s 3E500N25-RD4 chipbreaker is designed to produce predictable chips when machining formidably tough materials, which reduces tool clogging and machine stops. Stable chip formation leads to fewer interruptions and less manual intervention, improving overall productivity on the shop floor. The controlled chip flow also simplifies chip evacuation from the work zone, lowering the risk of surface damage and enabling longer uninterrupted cuts under challenging conditions. Prolonged tool life through advanced coating technology Belonging to the Tiger·tec Silver family, the WSM33S grade offers a balanced combination of hardness and thermal protection. The multilayer coated carbide helps resist thermal degradation and flank wear during sustained cutting of rostfreier Stahl and heat-resistant alloys. For operations where temperature build-up and edge robustness are critical, this coating contributes to a stable cutting edge and predictable wear patterns, extending tool life and reducing tool change frequency. Geometry tuned for quality surface finish and process reliability The insert geometry is optimised to prevent built-up edge and to maintain a consistent cutting action in high-adhesion materials. This results in a noticeable improvement in surface finish and reduces the need for secondary operations. By pairing the optimised geometry with the coated grade, the insert supports repeatable component quality and helps maintain tighter tolerances without sacrificing cycle time. Seamless integration into workshop tooling systems As an indexable turning insert, the design is compatible with common turning toolholders and clamping systems, offering straightforward replacement and indexing. The combination of the proven grade and chipbreaker allows for fewer insert variants across a range of rostfreier Stahl and superalloy tasks, simplifying inventory and setup. For production-focused workshops, this means more consistent uptime and clearer process planning, backed by Walter Tools’ manufacturing standards. Contact Metav Werkzeuge for expert recommendations on Walter Tools Tiger·tec Silver inserts and to align the GX24-3E500N25-RD4 WSM33S with specific machining parameters Technical data SKU: GX24-3E500N25-RD4-WSM33S-WALTER Designation: GX24-3E500N25-RD4 WSM33S Product type: Indexable turning insert Manufacturer: Walter Tools Series: Tiger·tec Silver Core data Grade: WSM33S Chipbreaker: 3E500N25-RD4 Material groups: S / M UID: GX24-3E500N25-RD4-WSM33S-WALTER Special features Coated carbide grade (Tiger·tec Silver) Suitable for rostfreier Stahl Designed for heat-resistant superalloys Walter Tools quality and repeatability FAQ What materials is this insert designed for? The GX24-3E500N25-RD4 WSM33S is designed primarily for rostfreier Stahl (material group M) and for heat-resistant superalloys (material group S), offering tailored performance in both families. How does the chipbreaker improve machining? The 3E500N25-RD4 chipbreaker promotes predictable chip formation, which reduces clogging and machine stops when the insert is used in Walter Tools turning applications. Which coating does the grade use and what benefit does it bring? The WSM33S grade uses Tiger·tec Silver, a multilayer coating that enhances heat resistance and wear protection, contributing to longer tool life in demanding turning operations. Is this insert suitable for continuous production runs? Yes, the combination of Tiger·tec Silver and the optimised chipbreaker makes the insert well suited to continuous production where stable cutting edges and consistent chip control are required. Can this insert be used with standard turning holders? The insert is an indexable turning insert designed for compatibility with common toolholder systems, allowing straightforward indexing and replacement during operations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only and do not imply any affiliation between our company and the named brands. The item offered is original, factory-new goods from the manufacturer Walter Tools.
GX24-3E500N25-RF7 WSM13S WSM13S Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance, reliable chip control and broad material coverage for efficient turning of stainless steels and heat‑resistant alloys; order the inserts directly via Metav Werkzeuge or consult our specialists for application advice. GX24-3E500N25-RF7 WSM13S indexable turning insert, Tiger·tec Silver – Walter Tools The GX24-3E500N25-RF7 WSM13S is a coated turning insert engineered for demanding stainless steel and superalloy applications, offering stable cutting edges and optimised chip control. Tiger·tec Silver coating for high wear resistance Optimised chipbreaker 3E500N25-RF7 for stable chips Suitable for stainless steels and superalloys Walter Tools production quality and repeatability Exceptional performance for tough materials The Tiger·tec Silver technology combined with the WSM13S grade delivers a clear advantage when machining demanding materials. The insert’s coated carbide substrate is formulated to resist abrasive wear and thermal degradation, resulting in prolonged tool life and reduced indexing intervals. For production environments working with stainless steel and heat‑resistant alloys, this composition supports consistent surface finish and predictable tool consumption. The technical design reduces the risk of built‑up edge and supports steady cutting parameters, which translates into fewer interruptions and more stable cycle times. Controlled chip formation and process stability An optimised chipbreaker 3E500N25-RF7 ensures reliable chip control even at varied feeds and depths of cut. The geometry promotes short, segmented chips that evacuate cleanly from the cut zone, lowering the chance of entanglement and protecting the workpiece surface. In practical terms, improved chip control reduces secondary operations for chip removal and minimises machine downtime. The combination of geometry and the WSM13S grade also maintains a stable cutting edge under thermal stress, allowing higher productivity without compromising component integrity. Practical benefits on the shop floor Designed for indexable turning operations, the insert suits both single‑point and multi‑op setups where repeatable performance is essential. The grade’s balance between toughness and heat resistance makes it particularly effective for interrupted cuts and where coolant access is limited. Process planners will benefit from fewer insert changes, simplified tooling logistics and enhanced first‑pass yield. For workshops aiming to raise throughput, the insert supports longer runs and more predictable maintenance intervals, aligning with goals for leaner production and lower unit costs. Reliability, traceability and brand assurance Walter Tools’ engineering focus is reflected in the insert’s dimensional accuracy and coating consistency. The WSM13S grade is positioned to deliver a combination of wear resistance and edge stability that supports dependable tool life across batches. Where consistent surface quality and repeatable machining cycles are required, choosing a proven grade reduces process variability. Documentation and traceability from a recognised supplier further support quality management and process audits. For demanding turning of stainless steels and superalloys, choose Walter Tools Tiger·tec Silver inserts — contact Metav Werkzeuge for expert application advice or to arrange prompt supply. Technical Data Article number: GX24-3E500N25-RF7-WSM13S-WALTER Product: Turning insert (indexable) ISO designation: GX24-3E500N25-RF7 WSM13S Grade: WSM13S Series: Tiger·tec Silver Chipbreaker: 3E500N25-RF7 Manufacturer: Walter Tools Material group: S / M Facts Suitable for stainless steel: Yes Suitable for superalloys/titanium: Yes Carbide type: Coated carbide Application: Turning / indexable insert use Typical benefits: Wear resistance, edge stability, chip control Special features Coating technology: Tiger·tec Silver Sortenbeschreibung: Coated carbide grade optimised for tough materials Optimised chip control geometry: 3E500N25-RF7 Primary workpiece groups: Stainless steels and heat‑resistant superalloys Intended use: Productive machining with improved tool life FAQ What materials is the GX24-3E500N25-RF7 WSM13S best suited for? The GX24-3E500N25-RF7 WSM13S is designed primarily for stainless steels and heat‑resistant superalloys, offering thermal stability and chip control suited to these groups. How does the Tiger·tec Silver coating improve performance? The Tiger·tec Silver coating on this insert enhances wear resistance and reduces thermal loading at the cutting edge, which supports longer tool life and steadier machining parameters. Which chipbreaker is integrated and what is the benefit? The insert features the 3E500N25‑RF7 chipbreaker, developed for consistent short chips and safe evacuation, reducing the risk of entanglement and improving surface quality. Is this insert appropriate for interrupted cuts? Yes, the combination of coated carbide and a robust edge geometry makes the insert suitable for interrupted cutting where edge strength and toughness are required. How is repeatability assured across production batches? Walter Tools’ manufacturing standards and grade specifications ensure dimensional accuracy and coating consistency, supporting repeatable tool life and process stability. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Mention of brand names is for identification and explanation only; no affiliation or endorsement by the named manufacturers is implied. The offered item is original and factory‑new.
GX24-3E500N25-RF7 WSM23S WSM23S Wendeplatten - Walter Tools
Combining the Tiger·tec Silver coating with the WSM23S grade provides enhanced cutting-edge stability and reliable chip control when machining stainless steel and heat-resistant superalloys; this increases process security and reduces downtime. Order the GX24-3E500N25-RF7 WSM23S insert via Metav Werkzeuge or consult our specialists for application support. GX24-3E500N25-RF7 WSM23S Indexable Turning Insert – Tiger·tec Silver, for stainless steel and superalloys (Walter Tools) The GX24-3E500N25-RF7 WSM23S is an indexable turning insert designed for stable, high-temperature machining of stainless steel and heat-resistant alloys, optimised for demanding production environments. Tiger·tec Silver coating for high thermal resistance WSM23S grade for stainless steel and superalloys Optimised 3E500N25-RF7 chip control Stable cutting edge and extended tool life Higher process security through heat-resistant coating The advanced Tiger·tec Silver coating combines thermal resilience with a low-friction surface, which leads to improved cutting-edge stability when facing the thermal loads typical of stainless steel and nickel-based alloys. For production managers this means fewer unscheduled tool changes and a more predictable machining outcome. The coating's behaviour under heat reduces adhesion and supports consistent chip formation, making it easier to maintain tolerances in series production. Grade selection explained: why WSM23S matters The WSM23S grade is a coated carbide formulation tuned for materials classified under ISO groups M and S. In practice, this means the substrate and coating system prioritise resistance to edge degradation and thermal softening. Operators new to these materials benefit from the grade’s balance between toughness and wear resistance: the result is reliable cutting performance across interrupted cuts and stable surface finish on complex geometries without sacrificing tool life. Chip control and geometry benefits for smoother turning The insert’s 3E500N25-RF7 chipbreaker geometry is engineered to produce short, manageable chips in a variety of turning conditions, limiting chip entanglement and improving coolant access. Better chip control reduces manual intervention at the machine and supports higher effective cutting parameters, contributing directly to productivity gains. When paired with a suitable holder, the geometry also helps maintain a steady contact between tool and workpiece, preserving the intended surface integrity. Practical handling and integration in production workflows This indexable insert fits standard toolholders compatible with the GX24 geometry and is supplied as a ready-to-use cutting edge solution, simplifying inventory management. The combination of coated carbide and optimised chipbreaker reduces the need for frequent regrinds and complex parameter tuning, which supports shorter setup times and a more efficient workflow. For procurement teams, the insert’s brand reliability from Walter Tools underpins consistent delivery and documented material classification. Contact Metav Werkzeuge for tailored application advice on the GX24-3E500N25-RF7 WSM23S insert and to discuss suitable toolholder pairings and machining parameters; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: GX24-3E500N25-RF7-WSM23S-WALTER Product type: Indexable turning insert Designation: GX24-3E500N25-RF7 WSM23S Series: Tiger·tec Silver Grade: WSM23S Manufacturer: Walter Tools Core data Applicable material groups: M, S Material compatibility: stainless steel Special features Coating: Tiger·tec Silver Chipbreaker: 3E500N25-RF7 Material WPL: S / M ISO designation: GX24-3E500N25-RF7 WSM23S FAQ What materials is this insert suitable for? The insert is suited to stainless steel and heat-resistant superalloys (ISO groups M and S); the WSM23S grade supports secure chip formation and edge stability for these materials. Is the GX24-3E500N25-RF7 WSM23S suitable for interrupted cuts? Yes, the WSM23S grade combined with the Tiger·tec Silver coating offers toughness and thermal resistance that help maintain a stable cutting edge during interrupted cutting. Which chipbreaker does this insert use and what is the benefit? The 3E500N25-RF7 chipbreaker is designed for reliable chip control, producing short chips that reduce entanglement and improve coolant reach. Can this insert be used with standard GX24 toolholders? The insert follows the GX24 geometry and is compatible with holders designed for that designation; pairing with a correctly rated holder preserves the intended performance. What production benefit does the Tiger·tec Silver technology provide? Tiger·tec Silver enhances thermal stability and reduces adhesive wear, which supports longer tool life and more consistent surface finishes in serial machining. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik-Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
GX24-3E500N25-RF8 WSM13S WSM13S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the robust WSM13S grade for reliable machining of stainless steel and heat-resistant alloys, ensuring stable chip formation and longer tool life; order or request application advice via Metav Werkzeuge for efficient integration into existing turning processes. GX24-3E500N25-RF8 WSM13S – Indexable turning insert with Tiger·tec Silver coating by Walter Tools GX24-3E500N25-RF8 WSM13S is an indexable turning insert designed for heavy-duty and demanding turning tasks, optimised for stainless steel and high-temperature superalloys Tiger·tec Silver coated carbide grade WSM13S Suitable for stainless steels and superalloys Stable cutting edge for continuous production GX24 geometry with 3E500N25‑RF8 chipbreaker High-performance cutting for demanding materials The combination of Tiger·tec Silver technology and the WSM13S grade delivers a balance of thermal resilience and wear resistance that benefits turning operations on stainless steel and heat-resistant alloys. The coated carbide substrate is engineered to resist thermal loading and reduce adhesion-related wear; this results in a stable cutting edge and improved dimensional consistency across long production runs. For shops working with materials that tend to work-harden or form built-up edges, the insert’s specification supports predictable chip formation and fewer unscheduled tool changes. Fewer tool changes through extended edge life A key advantage of this turning insert is reduced downtime due to extended edge life from the optimised coating and grade combination. The coated carbide and chipforming geometry promote effective chip control, limiting surface damage and enhancing repeatability. In practice, this translates to fewer tool indexings and lower machine idle time, improving overall productivity for batch production or continuous turning operations. The result is a measurable increase in process reliability, particularly where consistent surface finish and tight tolerances are required. Practical application and machining guidance The GX24 geometry together with the 3E500N25-RF8 chipbreaker is configured for robust turning strategies, enabling stable cuts at moderate to heavy depths of cut where chip evacuation is critical. The chipbreaker design supports segmented chips for secure removal, reducing the risk of entanglement and improving coolant access. For shops evaluating tooling options, the GX24-3E500N25-RF8 WSM13S insert performs well in interrupted cuts and applications with elevated cutting temperatures. For further machining parameters or material-specific recommendations, technical enquiries are welcome at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Speak to Metav Werkzeuge for tailored application advice and availability of the Walter Tools GX24-3E500N25-RF8 WSM13S insert; technical enquiries: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: GX24-3E500N25-RF8-WSM13S-WALTER Designation: GX24-3E500N25-RF8 WSM13S Product type: Indexable turning insert Manufacturer: Walter Tools Facts Series: Tiger·tec Silver Grade: WSM13S Chipbreaker: 3E500N25-RF8 Material group: S / M Special features Coating: Tiger·tec Silver (coated carbide) Suitable for: stainless steel and heat-resistant superalloys/titanium Strengths: stable chip formation, thermal resilience, long edge life FAQ Which materials can be machined with this insert? The GX24-3E500N25-RF8 WSM13S insert is specified for stainless steel and high-temperature superalloys (ISO group S and M), supporting operations that challenge thermal and edge stability. What benefits does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating enhances heat resistance and reduces adhesion, improving wear behaviour and contributing to a more stable cutting edge during extended runs. How does the 3E500N25‑RF8 chipbreaker affect machining? The 3E500N25‑RF8 chipbreaker is designed to produce segmented chips for reliable evacuation, which helps maintain consistent surface quality and reduces chip-related interruptions. Is this insert suitable for interrupted cutting and heavy depths of cut? Yes, the GX24 geometry combined with the WSM13S grade provides the edge robustness required for interrupted cuts and heavier machining conditions while keeping tool changes to a minimum. How is tool life improved with this grade? The coated carbide grade and optimised chip control lower thermal and mechanical wear, resulting in longer edge life and fewer tool indexings, which supports higher overall productivity. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany, info@walter-tools.com Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik‑Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
GX24-3E500N25-RF8 WSM23S WSM23S Wendeplatten - Walter Tools
Reliable Tiger·tec Silver coating combined with the WSM23S grade delivers extended tool life and consistent chip control for demanding applications; the GX24-3E500N25-RF8 WSM23S insert is therefore well suited to productive machining of stainless steels and heat‑resistant superalloys. Order original Walter Tools inserts from Metav Werkzeuge or consult our specialists for precision application support. GX24-3E500N25-RF8 WSM23S — Indexable turning insert, Tiger·tec Silver for stainless steel and superalloys (Walter Tools) The GX24-3E500N25-RF8 WSM23S is an indexable turning insert engineered for heavy‑duty and heat‑generating workpieces, optimising reliable chip formation and edge stability in applications involving stainless steels and superalloys. Tiger·tec Silver coated carbide grade WSM23S Optimised chip control geometry 3E500N25-RF8 Designed for stainless steels and superalloys Stable cutting edge for heavy engagement Delivering consistent productivity through advanced coating technology The combination of Tiger·tec Silver coating and the WSM23S cutting grade provides measurable advantages in continuous production. The coating enhances wear resistance and thermal stability, which reduces flank wear and extends the interval between index changes. For machine shops facing high‑temperature cutting of austenitic stainless steels or nickel‑based alloys, this means fewer interruptions and a lower cost per component. The technical design translates into improved process stability and predictable tool life, supporting planned production runs with repeatable results. Controlled chip formation and secure cutting edge for difficult materials The insert’s 3E500N25‑RF8 chipbreaker geometry is tuned for secure chip control under high heat and low thermal conductivity conditions common to stainless steels and superalloys. By promoting short, segmented chips and avoiding built‑up edge, the geometry improves surface finish and reduces the risk of workpiece damage. This targeted chip management helps maintain a stable cutting edge, enabling higher feeds or deeper cuts where the machine and workholding allow, so productivity gains can be realised without compromising part quality. Operational benefits for the workshop and production floor Selecting this insert supports efficiency improvements beyond the cutting contact itself. The coated carbide grade contributes to consistent tool life and reduces the frequency of tool changes, which in turn lowers setup time and machine downtime. Combined with systematic tool selection based on material group M (stainless steels) and S (heat‑resistant superalloys), the result is enhanced process security and dependable component quality. For procurement and production planners, the insert offers a clear path to optimising throughput while maintaining surface integrity and dimensional accuracy. For robust turning applications with Walter Tools' Tiger·tec Silver technology, contact Metav Werkzeuge for tailored recommendations and availability at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: GX24-3E500N25-RF8-WSM23S-WALTER Label: Drehwendeschneidplatte GX24-3E500N25-RF8 WSM23S Walter Tools Product type: Indexable turning insert Series / grade: Tiger·tec Silver, WSM23S Geometry / chipbreaker: 3E500N25-RF8 Manufacturer: Walter Tools Core data ISO designation: GX24-3E500N25-RF8 WSM23S Material code: S / M Applicable material groups: M (stainless steels), S (heat‑resistant superalloys) Features Coating technology: Tiger·tec Silver Grade: WSM23S, coated carbide Suitable for: stainless steel, superalloys Chip control geometry: 3E500N25-RF8 FAQ What materials is this insert designed to machine? The GX24-3E500N25‑RF8 WSM23S insert is designed primarily for material groups M and S — that is, stainless steels and heat‑resistant superalloys — where thermal load and adhesion tendencies demand a heat‑resistant coated grade. How does the Tiger·tec Silver coating affect tool life? The Tiger·tec Silver coating on the WSM23S grade increases thermal stability and wear resistance, which typically extends the usable life of the insert under demanding stainless steel and superalloy turning conditions. What is the role of the 3E500N25‑RF8 chipbreaker geometry? The 3E500N25‑RF8 geometry promotes secure chip control and segmented chip formation, reducing built‑up edge and improving surface finish when machining tough, low‑thermal‑conductivity materials. Is this insert suitable for high‑feed or heavy‑cut conditions? The stable cutting edge and optimised chip control make the insert appropriate for heavier engagements where machine power and rigidity permit, with the benefit of improved process security and consistent results. Which brand manufactures this insert and what should be expected regarding authenticity? Walter Tools manufactures the insert; the GX24‑3E500N25‑RF8 WSM23S is supplied as an original, factory‑new insert from the manufacturer and is intended for professional industrial use. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is original, factory‑new goods of the manufacturer (Walter Tools).
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com