GX34-3E400N04-CF5 WSM43G WSM43G Wendeplatten - Walter Tools
Benefit from the combination of Walter Tools’ Tiger‑tec Gold coating and the WSM43G grade for reliable machining of tough alloys and rostfreier Stahl; the optimised CF5 chipbreaker supports consistent chip control and extended edge life. Order directly via Metav Werkzeuge or ask our consultants for tailored application advice. GX34-3E400N04-CF5 WSM43G – Turning indexable insert with Tiger‑tec Gold coating (Walter Tools) GX34-3E400N04-CF5 WSM43G is a high‑performance turning insert engineered for stable cutting in rostfreier Stahl and high‑temperature alloys, optimised for secure chip formation and long tool life Tiger‑tec Gold coating for long edge life Optimised chip control with CF5 chipbreaker Suited to rostfreier Stahl and superalloys Precision ground geometry for stable cutting Consistent performance for difficult materials The WSM43G grade, part of the Tiger·tec Gold series, is formulated as a coated carbide cutting material to meet the demands of tough‑to‑machine workpieces. Its composition and coating technology increase heat resistance and reduce edge wear under thermal and mechanical stress, which translates into more predictable cycle times and fewer unplanned tool changes. When machining rostfreier Stahl and heat‑resistant superalloys, a combination of grade chemistry and surface treatment is critical: the insert’s design promotes secure chip formation and resists built‑up edge, helping maintain component quality through long production runs. Design that improves process reliability An integral part of the insert’s performance is the chipbreaker CF5 geometry. The CF5 profile guides chips away from the cutting zone, limits entanglement and reduces the risk of re‑cutting, which stabilises the cutting process and improves surface finish. The insert’s precision ground faces and rake geometry also support a stable cutting edge and consistent contact conditions at the tool‑workpiece interface. For workshops focused on repeatable outcomes, these design elements lower scrap rates and reduce downtime caused by tool failures. Practical advantages on the shop floor As an indexable turning insert, this solution reduces per‑part tooling cost by enabling economical index changes rather than full tool replacements. The WSM43G grade is categorised for the ISO material groups M (rostfreier Stahl) and S (superalloys & titanium), which means it is specifically intended for applications where heat generation and material toughness place extra demands on the cutting edge. For machinists less familiar with ISO groupings: M denotes stainless steels and similar alloys; S covers heat‑resistant superalloys and titanium, which typically require heat‑resistant grades and stable edge geometry to maintain productivity. Compatibility and selection guidance This insert is supplied by Walter Tools in the Tiger‑tec Gold series and is best selected when process goals include long edge life and secure chip control for rostfreier Stahl and high‑temperature alloys. Toolholders and cutting parameters should be matched to the insert geometry and workpiece class: moderate feeds and controlled cutting speeds often extend tool life in these materials. For tailored recommendations on cutting data, toolholder compatibility or nesting strategies in serial production, consult Metav Werkzeuge’s technical advisors to ensure optimum tool utilisation and process stability. For technical guidance on Walter Tools inserts such as the GX34-3E400N04-CF5 WSM43G, contact Metav Werkzeuge for expert advice and fast supply: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: GX34-3E400N04-CF5-WSM43G-WALTER ISO designation: GX34-3E400N04-CF5 WSM43G Series: Tiger‑tec Gold Brand: Walter Tools Facts Grade: WSM43G Chipbreaker: 3E400N04-CF5 Material groups: S / M Special features Coating technology: Tiger·tec Gold (coated carbide) Suitable for: rostfreier Stahl, superalloys and titanium Application: turning / indexable insert FAQ What materials is this insert intended for? The GX34-3E400N04-CF5 WSM43G insert is designed for rostfreier Stahl and high‑temperature superalloys (ISO groups M and S), where heat resistance and stable chip control are required. How does the CF5 chipbreaker affect machining? The CF5 chipbreaker promotes controlled chip formation and directed chip evacuation, reducing re‑cutting and supporting a consistent surface finish when using the WSM43G grade. Is the WSM43G grade suited to titanium machining? Yes; WSM43G is categorised for S materials, which include titanium and heat‑resistant alloys, offering enhanced thermal stability and edge strength for these demanding applications. Can this insert reduce tool change frequency? By combining the Tiger·tec Gold coating with the robust WSM43G grade, the insert supports extended edge life and therefore fewer index changes, improving uptime in serial operations. Who should be contacted for cutting data and holder compatibility? Metav Werkzeuge can provide application‑specific cutting data and advise on suitable toolholders for the GX34-3E400N04-CF5 WSM43G insert. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany, info@walter-tools.com Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
GX34-3E400N04-GD6 WSM33G WSM33G Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance from the Tiger·tec Gold technology and the WSM33G grade’s stability for machining stainless steel and heat-resistant alloys, ensuring consistent productivity and predictable tool life; order or request application advice via Metav Werkzeuge. GX34-3E400N04-GD6 WSM33G – Indexable turning insert, Tiger·tec Gold (Walter Tools) GX34-3E400N04-GD6 WSM33G is an indexable turning insert designed for demanding turning tasks in stainless steel and heat-resistant superalloys and titanium Tiger·tec Gold coating for enhanced tool life WSM33G grade tailored for stainless steel and S Stable cutting edge for heavy-duty machining Reliable chip control in difficult-to-machine materials Durable coating and grade for consistent productivity The Tiger·tec Gold coating combined with the WSM33G carbide grade delivers a balance of wear resistance and edge stability for continuous turning operations. This combination was developed to support machining of stainless steel and demanding superalloys (ISO group S), where heat generation and built-up edge are common challenges. The coated carbide construction means flank wear and crater wear are reduced under elevated temperatures, which leads to longer intervals between indexings and a steadier component surface finish. For production environments seeking predictable tool life, this insert offers a reliable baseline for process planning. Geometry and chip management that aid process security The chipbreaker and geometry identified by 3E400N04-GD6 provide controlled chip formation and evacuation during moderate to heavy cuts. A consistent chip flow minimises re-cutting and reduces the risk of surface damage on turned parts. The insert’s form supports a stable shear zone, which in turn helps to maintain a sharper cutting edge under thermal and mechanical load. For workshops dealing with long, continuous turning cycles, the improved chip control contributes directly to reduced machine downtime and simplified swarf handling. Application guidance and material scope This insert is intended for use on stainless steel (ISO group M) and heat-resistant superalloys or titanium alloys (ISO group S), covering a broad swath of aerospace, energy and medical component work. The coated carbide construction is particularly suitable where thermal resilience and edge security are required, especially in interrupted cuts or mixed batch production. While specific cutting data depends on the machine, workholding and coolant strategy, the insert’s characteristics favour stable cutting regimes and moderate to high cutting speeds where thermal control is part of the process window. Contact Metav Werkzeuge today for tailored cutting data, availability and to discuss the Walter Tools GX34-3E400N04-GD6 WSM33G insert for specific applications Technical Data Article number: GX34-3E400N04-GD6-WSM33G-WALTER Designation: GX34-3E400N04-GD6 WSM33G Type: Indexable turning insert Brand: Walter Tools Core data Series: Tiger·tec Gold Grade: WSM33G Chipbreaker: 3E400N04-GD6 Applicable ISO groups: M, S Special features Coating: Tiger·tec Gold Material: coated carbide Suitable for: stainless steel (ISO group M) Suitable for: heat-resistant superalloys and titanium (ISO group S) FAQ What materials is this insert suitable for? The GX34-3E400N04-GD6 WSM33G insert is designed for machining stainless steel (ISO group M) and heat-resistant superalloys and titanium (ISO group S), offering thermal resilience and edge stability for these groups. How does the Tiger·tec Gold coating benefit performance? The Tiger·tec Gold coating on the WSM33G grade improves wear resistance and helps to maintain a stable cutting edge under elevated temperatures, which supports longer index life and more consistent part quality with this Walter Tools insert. Which chipbreaker code should be referenced for machining strategy? Refer to the 3E400N04-GD6 chipbreaker geometry when planning feeds and depths of cut; its design promotes controlled chip formation and evacuation in difficult-to-machine materials. Is this insert intended for interrupted cuts or continuous turning? The combination of WSM33G grade and Tiger·tec Gold coating provides versatility for both interrupted cuts and continuous turning, but best results depend on matching cutting parameters and tooling set-up to the specific workpiece alloy. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered marks are mentioned for descriptive purposes only and do not imply any affiliation between our company and the named manufacturers. The offered item is an original, factory-new product of the manufacturer Walter Tools.
LCGX050203-F57 WKP35S Wendeplatten - Walter Tools
Benefit from high process reliability, wide material compatibility and a robust Tiger·tec Silver grade for stable chip formation and long tool life — order the insert via Metav Werkzeuge or consult our advisors for application guidance. LCGX050203-F57 WKP35S — Drill/Reaming Indexable Insert, Tiger·tec Silver (Walter Tools) The LCGX050203-F57 WKP35S is a rectangular drill/reaming indexable insert engineered for productive machining of steel and cast iron in demanding drilling and reaming operations Tiger·tec Silver coating for long tool life For machining steel and cast iron (P / K) 7° clearance angle for stable cutting Rectangular form with 0.3 mm corner radius Increased productivity for steels and cast iron The combination of the Tiger·tec Silver coating and the WKP35S cutting grade delivers improved wear resistance and consistent cutting performance when machining steels (P) and cast irons (K) as defined by ISO 513. The coated carbide substrate is optimised for the heat and chip forms typical of steel and for the abrasive nature and breakable chips common in cast iron, which reduces unplanned tool changes and keeps cycle times steady. By selecting a grade that balances toughness and abrasion resistance, machining windows can be widened, enabling higher cutting speeds or longer tool life without sacrificing component quality. Stable cutting geometry for repeatable results The insert’s 7° clearance angle and 0.3 mm corner radius provide a secure cutting edge that minimises vibration and flank wear during bore enlargement and reaming passes. The rectangular form and defined tolerance class support precise seating in toolholders, contributing to repeatable bore quality and surface finish. These geometric features reduce the risk of chatter and improve dimensional stability, which is especially relevant where concentricity and bore roundness are critical for downstream assembly. Reliable chip control and process integration Equipped with the F57 chipbreaker, this insert promotes predictable chip formation and evacuation in interrupted and continuous cuts common to drilling and reaming. The plate geometry (size 05, thickness 02) has been designed for secure clamping and efficient heat dissipation, enhancing tool life in serial production. Using a standard ISO designation simplifies tool management and replacement, allowing integration into existing tool systems without complex requalification procedures. Practical advantages for workshop standardisation The standardised ISO designation and clear material coding (P / K) make inventory management straightforward and support quicker tooling decisions on the shop floor. The insert’s balance of resilience and wear resistance reduces downtime from tool changes and supports a more economical machining process. When combined with appropriate holders and process parameters, the insert contributes to a stable production flow and measurable productivity gains. Contact Metav Werkzeuge for a tailored application recommendation on Tiger·tec Silver WKP35S inserts or to request a specification sheet and availability from Metav Werkzeuge, Parkring 45, Emmerich — eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data Article number: LCGX050203-F57-WKP35S-WALTER ISO designation: LCGX050203-F57 WKP35S Type: Drill/Reaming indexable insert Brand: Walter Tools Facts Clearance angle: 7° Corner radius: 0.3 mm Plate size: 05 Plate thickness: 02 Tolerance class: G Special features Series: Tiger·tec Silver Grade: WKP35S (coated carbide) Chipbreaker: F57 Form: Rectangular Material suitability: Steel (P) and Cast iron (K) Execution: X FAQ What materials is this insert suitable for? The LCGX050203-F57 WKP35S insert is specified for steel (P) and cast iron (K), reflecting the WKP35S grade and Tiger·tec Silver series suitability for these ISO material groups. How does the F57 chipbreaker affect performance? The F57 chipbreaker on the insert promotes controlled chip formation and evacuation during drilling and reaming, improving process stability and reducing the risk of chip-related surface damage. Which geometric features ensure accurate bore quality? The combination of a 7° clearance angle, a 0.3 mm corner radius and the rectangular seating yields stable cutting engagement and repeatable bore dimension and surface finish with the LCGX050203-F57 WKP35S insert. Is the insert compatible with standard toolholders? The insert uses an ISO-style designation and standard plate dimensions (size 05, thickness 02), facilitating compatibility with holders designed for this family of drill/reaming indexable inserts Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
LCGX050203-F57 WSP45G Wendeplatten - Walter Tools
High process security and broad material coverage ensure reliable bore finishing and longer tool life; the combination of the Tiger·tec Gold coating and the F57 chipbreaker delivers stable chip control and consistent surface quality. Order the insert directly via Metav Werkzeuge or consult the technical team for specific application setup. LCGX050203-F57 WSP45G — Drilling/reaming indexable insert, Tiger·tec Gold, 7° clearance (Walter Tools) A LCGX050203-F57 WSP45G indexable insert engineered for efficient drilling and bore-enlargement in steel, stainless steel and heat-resistant alloys Tiger·tec Gold PVD coating for long tool life Suitable for steel, stainless and superalloys Rectangular insert with 0.3 mm corner radius 7° clearance angle for stable cutting Consistent high productivity through advanced coating technology The Tiger·tec Gold coating combined with the WSP45G cemented carbide grade provides enhanced thermal resistance and wear protection, which translates into longer tool life and fewer insert changes. In practical terms, this means more uninterrupted operating time and reduced tooling costs per component. The coated grade is optimised for the temperature and chip-formation challenges of machining steels, stainless steels and superalloys, enabling higher cutting parameters while maintaining dimensional stability and reliable edge behaviour. Controlled chip formation for safer, repeatable machining The engineered F57 chipbreaker and the 0.3 mm corner radius deliver predictable chip flow and reduced risk of built-up edge during interrupted cuts. The rectangular form gives a stable cutting seat in the toolholder and supports secure clamping forces, improving repeatability in series production. Together with the 7° clearance angle, the geometry reduces friction at the flank face and supports consistent surface finish, which is particularly beneficial when producing bores to tight tolerances. Application flexibility and process security in demanding materials Designed for the ISO material groups P, M and S, this insert covers a wide range of workshop tasks from general steel turning to stainless applications and work on heat-resistant superalloys. The tolerance class G and the proven series construction support predictable insert indexing and interchangeability across suitable toolholders. For operations seeking a balance of productivity and process reliability, the combination of insert geometry and the Tiger·tec Gold technology delivers measurable advantages in cycle time and tool-change intervals. Contact Metav Werkzeuge today to review the LCGX050203-F57 WSP45G insert for the intended application and to receive tailored recommendations on grades and machining parameters — eMail: info@metav-werkzeuge.com · Tel: +49 2822 7131930 Technical data Article number: LCGX050203-F57-WSP45G-WALTER SKU: LCGX050203-F57-WSP45G-WALTER Product type: Drilling/reaming indexable insert Series: Tiger·tec Gold Grade/sort: WSP45G Facts Clearance angle: 7° Corner radius: 0.3 mm Insert size: 05 Thickness code: 02 Tolerance class: G Special features F57 chipbreaker Rectangular insert form Coating: Tiger·tec Gold (PVD) Material compatibility: steel (P), stainless steel (M), superalloys/titanium (S) Execution/version: X Manufacturer: Walter Tools FAQ Which materials are suitable for this insert? The LCGX050203-F57 WSP45G insert is suitable for machining steel, stainless steel and heat-resistant superalloys (ISO groups P, M, S) thanks to the Tiger·tec Gold coating and the WSP45G grade. What benefits does the Tiger·tec Gold coating provide? Tiger·tec Gold improves thermal resistance and wear protection on the LCGX050203-F57 WSP45G, enabling higher cutting parameters and longer tool life in demanding drilling and reaming operations. How does the F57 chipbreaker affect machining? The F57 chipbreaker promotes controlled chip formation and evacuation, reducing the likelihood of built-up edge and supporting consistent surface quality during interrupted or continuous cuts. Is the insert compatible with standard toolholders? The insert follows common insert dimensions and tolerance class G, allowing use with matching holders designed for the LCGX050203-F57 form and size. What is the significance of the 0.3 mm corner radius? A 0.3 mm corner radius balances edge strength and dimensional accuracy, providing improved edge stability for bore finishing while maintaining acceptable surface integrity. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Mention of brand names here is for explanation only and does not imply any affiliation between Metav Werkzeuge and the respective trademark owners. The offered item is an original, factory-new product of the manufacturer.
LCGX050203-F57 WXP40 WXP40 Wendeplatten - Walter Tools
Take advantage of the combination of uncoated carbide WXP40, a 7° clearance angle and an F57 chipbreaker for controlled chip flow and consistent performance; order the insert directly via Metav Werkzeuge or consult the technical team for application-specific guidance. LCGX050203-F57 WXP40 – Rectangular Drilling/Boring Indexable Insert, F57 Chipbreaker (Walter Tools) The LCGX050203-F57 WXP40 is a rectangular insert for drilling and boring operations, engineered to promote stable chip formation and repeatable cutting results in general metal‑cutting processes. Uncoated carbide grade WXP40 7° clearance angle for stable cutting 0.3 mm corner radius for repeatable edges F57 chipbreaker for controlled chip flow Durable geometry for reliable chip control and repeatability The insert features a rectangular form with a 0.3 mm corner radius, a geometry that supports predictable cutting forces and helps maintain stable engagement in drilling and boring tools. The combination of the F57 chipbreaker and the specified 7° clearance reduces the tendency for long, stringy chips and encourages fragmentation where needed; this leads to fewer interruptions for chip removal and steadier torque behaviour. For production environments that prioritise repeatable component quality, these design choices translate into fewer tool changes and more consistent hole finishes. Material class and process considerations for predictable tool life Manufactured in the uncoated carbide grade WXP40, the insert offers a baseline of wear resistance and toughness typical of solid carbide grades. The grade is described as uncoated, which can be advantageous where coating adhesion or thermal stability may be a concern. Material suitability should be verified against the product matrix supplied by the manufacturer to ensure optimal cutting data; the WXP40 designation indicates the cutting material rather than a universal guarantee across all alloys. When paired with appropriate feeds and speeds, the insert promotes consistent tool life and stable machining cycles, supporting improved productivity and lower overall tooling costs. Practical integration and handling in a production setting The insert is supplied in a standard size code (05) and thickness code (02) with a tolerance class of G, enabling straightforward integration into compatible drilling and boring toolholders. The rectangular geometry and the clear specification of chipbreaker and clearance make setup and indexation predictable, allowing for rapid replacement and minimal downtime. For shops implementing serial production or small‑batch work, the capacity to maintain geometry across indices helps preserve process control and surface quality. For any uncertainty regarding holder compatibility or cutting data, the Metav Werkzeuge team can provide practical guidance and application sheets. Contact Metav Werkzeuge for technical advice or to request the LCGX050203-F57 WXP40 insert from Walter Tools — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: LCGX050203-F57-WXP40-WALTER Designation: LCGX050203-F57 WXP40 Product type: Bohr-/Aufbohrwendeschneidplatte (drilling/boring indexable insert) Brand: Walter Tools Shape: Rectangular Facts Size code: 05 Thickness code: 02 Corner radius: 0.3 mm Clearance angle: 7° Chipbreaker: F57 Tolerance class: G Special features Grade: WXP40 (uncoated carbide) Series: Walter Schneidstoffsorte - Serie offen Execution: X Material information: catalogue dependent FAQ What materials is this insert suitable for? Material suitability must be checked against the manufacturer's product matrix; the insert in WXP40 is an uncoated carbide grade and suitability depends on the specific workpiece material and machining parameters. Is the insert coated? The cutting material for the LCGX050203-F57 WXP40 is specified as uncoated carbide, which can be preferable in situations where coating interference or regrinding is a consideration. How does the F57 chipbreaker affect machining? The F57 chipbreaker is designed to encourage controlled chip formation during drilling and boring operations, improving evacuation and reducing the risk of chip-related interruptions. Can this insert be indexed or rotated during use? Yes, the rectangular insert geometry supports indexing where the toolholder permits; following the tolerance class G and correct clamping practice ensures repeatable seating and positioning. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
LCGX06T204-F57 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the WKP35S grade to achieve consistent chip formation and extended tool life in machining steel and cast iron; the robust chipbreaker F57 and precise geometry support stable, reproducible production. Order or request material-specific advice directly via Metav Werkzeuge if needed. LCGX06T204-F57 WKP35S drill/boring indexable insert — Tiger·tec Silver coated, for steel and cast iron (Walter Tools) A LCGX06T204-F57 WKP35S rectangular indexable insert designed for drilling and boring operations, optimised for precision machining of steel and cast iron with a small corner radius and controlled chip formation Tiger·tec Silver coated carbide grade WKP35S Optimised chipbreaker F57 for consistent chips 7° clearance angle and 0.4 mm corner radius Suitable for steel (P) and cast iron (K) Consistent cutting performance for demanding steels and cast iron The combination of the WKP35S grade and Tiger·tec Silver coating delivers a stable cutting edge adapted to the thermal and abrasive loads typically encountered when machining steel and cast iron. The coated carbide substrate improves wear resistance and reduces friction, which contributes to longer service intervals and fewer tool changes. This results in measurable productivity gains where repeatable component quality and uptime are priorities. Controlled chip formation and reliable surface quality The integrated chipbreaker F57 is engineered to produce predictable, short chips under the typical cutting conditions for P and K material groups. Short, well managed chips reduce the risk of surface damage and machine interruptions. Combined with the 0.4 mm corner radius, the geometry supports good edge strength while allowing fine surface finishes on bore and reaming operations. These features make the insert particularly suitable where process reliability and consistent part tolerances matter. Geometry and specification that reduce machining variability A 7° clearance angle and rectangular plate form provide a stable seating and defined cutting engagement, lowering vibration sensitivity in many bores and enlargements. The plate thickness T2, size 06 and tolerance class G support precise insert positioning and predictable tool behaviour. For shops seeking to standardise operations, the defined geometry simplifies tool setup and reduces trial-and-error when transferring programs between machines. Practical benefits: fewer interruptions, easier planning By selecting a Tiger·tec Silver grade with the WKP35S chemistry, workshops benefit from extended edge life and improved process security under mixed production loads. The insert’s execution and chip control reduce unplanned stoppages and make downstream handling easier, which helps to maintain flow in high-mix, low-volume or repetitive production environments. For customers requiring clarification on parameters or compatible holders, technical consultation can clarify best-practice feeds and speeds for specific alloys. For tailored application advice, availability of Walter Tools WKP35S inserts and material‑specific recommendations, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data SKU: LCGX06T204-F57-WKP35S-WALTER Item: Bohr-/Aufbohrwendeschneidplatte LCGX06T204-F57 WKP35S Manufacturer: Walter Tools Core specifications Clearance angle: 7° Corner radius: 0.4 mm Plate size: 06 Plate thickness: T2 Tolerance class: G Chipbreaker: F57 Plate form: rectangular Features & applications Coating / grade: WKP35S (coated carbide) Series: Tiger·tec Silver Applicable materials: Steel (P), Cast iron (K) Execution: X Typical use: drilling and boring indexable insert Suitable for precision machining and stable chip control FAQ What materials is this insert suitable for? The LCGX06T204-F57 WKP35S insert is specified for steel (P) and cast iron (K) applications, using the WKP35S coated carbide to handle typical thermal and abrasive loads. How does the chipbreaker F57 benefit machining? The chipbreaker F57 promotes short, controlled chips during drilling and boring, lowering the risk of surface damage and machine interruptions when using the Walter Tools insert. What does the 0.4 mm corner radius affect? A 0.4 mm corner radius increases edge strength and helps achieve consistent surface finish in bore enlargements while balancing cutting forces for repeatable results. Is this insert compatible with standard rectangular holders? The rectangular plate form and specified T2 thickness make the insert compatible with holders designed for the LCGX06T204-F57 geometry; machine-specific holder selection should be confirmed for optimal performance. Can the WKP35S grade be used for high-speed applications? The Tiger·tec Silver technology improves wear resistance and thermal behaviour; however, recommended speeds and feeds depend on the specific steel or cast iron alloy and the machine setup—consult Metav Werkzeuge for tailored parameters. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany. Protected trademarks and trade names are the property of their respective owners. Walter Tools (Walter AG) is part of the Sandvik Group. The offered article is original, brand-new goods supplied by the manufacturer.
LCGX06T204-F57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of the Tiger·tec Gold cutting grade and precise geometry to secure stable cutting performance across steel, stainless steel and heat‑resistant alloys, while reducing tool changes; order via Metav Werkzeuge or consult our technical team for process selection. LCGX06T204-F57 WSP45G drill/boring indexable insert — Tiger·tec Gold PVD, r0.4, 7° (Walter Tools) A LCGX06T204-F57 WSP45G drill/boring indexable insert designed for reliable machining of steel, stainless steel and superalloys in high‑productivity drilling and boring operations. Tiger·tec Gold PVD coating for long tool life Suitable for steel, stainless steel and superalloys Rectangular insert with 0.4 mm corner radius Consistent performance for demanding alloys The combination of the WSP45G cutting grade and the Tiger·tec Gold PVD coating provides a balance of toughness and wear resistance that suits interrupted cuts and higher temperatures common in steel and stainless‑steel machining. The coated carbide substrate supports controlled chip formation and a durable cutting edge, which translates into longer tool life and fewer tool changes. This results in higher machine uptime and more predictable process windows for series production. Geometry that improves hole quality and repeatability The rectangular plate form with a 0.4 mm corner radius and a 7° relief angle is engineered to produce consistent hole finishes and dimensional stability during drilling and boring. The modest corner radius offers a compromise between strength and cutting edge sharpness, reducing the risk of edge chipping while helping to maintain surface integrity. Such geometry is particularly advantageous for tasks where hole tolerance and surface condition are critical to subsequent assembly or finishing operations. Integration into productive machining cycles Marked as LCGX06T204‑F57 with chipbreaker F57, this insert is straightforward to integrate into standard drill/boring toolholders and tool‑change systems. The grade is specified for machining groups P, M and S — in other words, steel, stainless steel and superalloys — which simplifies tooling choices across mixed‑material production runs. The result is improved process security and simpler tool inventory management for production planners and shopfloor engineers. Contact Metav Werkzeuge for tailored application advice on Walter Tools Tiger·tec Gold inserts and ensure the right insert selection for the machining task at hand Technical data SKU: LCGX06T204-F57-WSP45G-WALTER Article: Bohr-/Aufbohrwendeschneidplatte (drill/boring indexable insert) Manufacturer: Walter Tools Series: Tiger·tec Gold Grade: WSP45G Execution: X Designation without grade: LCGX06T204-F57 ISO designation: LCGX06T204-F57 WSP45G UID: LCGX06T204-F57-WSP45G-WALTER Dimensions / Core data Relief angle: 7° Corner radius: 0.4 mm Plate size: 06 Thickness: T2 Tolerance class: G Materials & special features Coating technology: Tiger·tec Gold (PVD) Chipbreaker: F57 Plate form: rectangular Material suitability: P / M / S (steel / stainless steel / superalloys and titanium) Intended application: drilling and boring operations FAQ What materials can this insert machine reliably? The LCGX06T204‑F57 WSP45G insert is specified for groups P, M and S — suitable for steel, stainless steel and heat‑resistant superalloys — making it versatile for mixed‑material production. How does the Tiger·tec Gold coating affect performance? The Tiger·tec Gold PVD coating enhances wear resistance and supports stable edge behaviour under elevated temperatures, allowing the WSP45G grade to maintain cutting performance over longer cycles. Which geometry features improve hole finish? The rectangular form with a 0.4 mm corner radius and a 7° relief angle promotes edge strength and stable chip flow, which together contribute to consistent surface quality and dimensional repeatability in drilled holes. Is the insert compatible with standard holders? The LCGX06T204‑F57 designation follows common indexable insert conventions and is compatible with matching drill/boring toolholders designed for this insert style and size. Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is original, factory‑new manufacturer goods of Walter Tools. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
LCGX06T204-F57 WXP40 Wendeplatten - Walter Tools
Take advantage of the combination of consistent chip control, economical uncoated carbide, and secure seating geometry for uninterrupted drilling and boring operations. Order the insert directly via Metav Werkzeuge or consult the technical team for material-specific recommendations. LCGX06T204-F57 WXP40 Drilling/Boring Indexable Insert, uncoated carbide, chipbreaker F57 — Walter Tools The LCGX06T204-F57 WXP40 is a rectangular indexable insert designed for drilling and boring applications, offering controlled chip formation and reliable cutting performance in general machining tasks. Uncoated carbide WXP40 grade Chipbreaker F57 for consistent chip control 7° relief angle for secure seating Rectangular 06 form, 0.4 mm corner radius Consistent chip control reduces downtime and scrap The inclusion of the F57 chipbreaker ensures predictable chip formation, which directly reduces tool clogging and machine stoppages. With controlled chips, coolant flow and evacuation become more efficient, improving surface finish and lowering the risk of rework. For operations where stable chip behaviour is essential—such as long holes or interrupted cuts—this insert delivers measurable process stability and fewer operator interventions. Economical substrate for high-volume throughput Manufactured in the WXP40 uncoated carbide grade, the insert provides a balance between edge stability and cost-effectiveness. The uncoated substrate is ideal where a robust cutting edge and economical consumption are priorities. For batch production and shops with mixed workpiece materials, the grade offers broad applicability; however, it is recommended to check the product matrix for exact material suitability before series use to ensure optimised tool life. Geometry and tolerance for repeatable accuracy The rectangular 06 form, 0.4 mm corner radius and 7° relief angle combine to give reliable seating and repeatable cutting positions in standard toolholders. The defined geometry supports dimensional consistency across multiple indexings, which is particularly beneficial in production environments that demand tight tolerances. The tolerance class G further underlines the component’s suitability for precision applications where stable clamping and minimal runout are required. Integration into existing tooling with clear handling advantages With a plate thickness of T2 and execution type X, the insert integrates readily into common drilling and boring tool systems that accept format 06 inserts. Handling and replacement are straightforward thanks to the standardised form, reducing downtime during changeovers. For customers seeking proven brands, Walter Tools supplies the insert with a focus on process security and consistent tool performance. For assured process reliability using Walter Tools' WXP40 grade inserts, contact Metav Werkzeuge for application advice and fast procurement — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: LCGX06T204-F57-WXP40-WALTER Designation: LCGX06T204-F57 WXP40 Product type: Drilling/Boring indexable insert Grade: WXP40 Chipbreaker: F57 Facts Relief angle: 7° Corner radius: 0.4 mm Form: 06 (rectangular) Thickness: T2 Tolerance class: G Special features Uncoated carbide substrate (catalogue-dependent) Series: Walter Schneidstoffsorte - Serie offen Execution: X Rectangular insert for drilling/boring applications Check product matrix for material suitability FAQ What materials is this insert suitable for? The LCGX06T204-F57 WXP40 insert is supplied in the WXP40 uncoated carbide grade; material suitability should be verified in the product matrix before series machining to ensure optimal performance. How does the F57 chipbreaker affect machining? The F57 chipbreaker on the insert promotes consistent chip control, which improves coolant evacuation and surface quality while reducing the likelihood of built-up edge and stoppages during drilling and boring operations. What is the significance of the 7° relief angle? A 7° relief angle provides secure seating in the toolholder, helping to maintain cutting geometry and repeatable positioning, which supports dimensional accuracy across multiple indexings. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world's leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are used solely for explanatory purposes. There is no affiliation between our company and the brands mentioned. The offered article is an original, brand-new product from the manufacturer.
LCMX050203-B57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of WKP25S grade and Tiger‑tec Silver coating for extended tool life and consistent chip control; the rectangular form with a 0.3 mm corner radius and 7° clearance angle delivers reliable finishes in steel and cast iron operations. Order directly via Metav Werkzeuge or consult our advisers for application-specific guidance. LCMX050203-B57 WKP25S rectangular drilling/boring indexable insert for steel & cast iron — Walter Tools LCMX050203-B57 WKP25S is a rectangular indexable insert engineered for drilling and boring operations in steel and cast iron, combining a coated carbide grade and a dedicated chipbreaker for stable and productive machining. Tiger‑tec Silver coating for long tool life Suited for steel and cast iron machining 7° clearance angle for stable cutting 0.3 mm corner radius for consistent surface finish Boosted productivity through optimised grade and coating The combination of the WKP25S grade with the Tiger‑tec Silver coating translates into measurable productivity gains in serial operations. The coated carbide substrate resists abrasive wear and thermal loads typical of steel and cast iron machining, which reduces changeover frequency and minimises unplanned downtime. As a result, cycle times become more predictable and tool-related variability is reduced, supporting tighter process control and higher output per shift. Precise chip control and cutting stability Built around a defined chipbreaker B57 and a rectangular geometry, the insert ensures predictable chip formation and evacuation when machining both steel and cast iron. The 7° clearance angle promotes steady engagement with the workpiece, decreasing chatter and improving dimensional stability. This leads to more consistent toolpaths and fewer scrap parts, particularly when the component geometry demands repeatable hole or bore quality. Durable edge geometry for improved surface quality A 0.3 mm corner radius delivers a balance between cutting strength and surface finish; the robust edge resists micro‑chipping while smoothing the transition on the bore wall. The coated cutting surface maintains its cutting line longer under thermal stress, which means fewer interruptions for dressing or insert changes. For manufacturers prioritising component appearance or close tolerances, the geometry and coating together contribute to reliable finishing performance. Practical selection and application guidance The rectangular indexable insert form and its compatibility with the P / K material groups (steel and cast iron) make it appropriate for drilling and boring operations where both wear resistance and chip handling are required. Selection should consider spindle speed, feed and the machine’s rigidity; when combined with appropriate holder choice and coolant strategy, the insert supports steady, high‑quality results. For application matching, specify the plate size and thickness to ensure holder compatibility. Contact Metav Werkzeuge for tailored application advice and precise ordering information for Walter Tools inserts via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: LCMX050203-B57-WKP25S-WALTER Designation: LCMX050203-B57 Product type: Drilling/boring indexable insert Brand: Walter Tools Series: Tiger‑tec Silver Grade: WKP25S Execution: X Tolerance class: M Facts Clearance angle: 7° Corner radius: 0.3 mm Plate size: 05 Plate thickness: 02 Special features Chipbreaker B57 Rectangular plate form Coated carbide grade Material suitability: steel (P) and cast iron (K) Series description: coated carbide, optimised for process stability FAQ Which workpiece materials are suitable with this insert? The LCMX050203-B57 WKP25S insert is suitable for steel and cast iron machining, corresponding to the P and K ISO groups, which the Tiger‑tec Silver grade is optimised to handle. What does the WKP25S grade signify? WKP25S is Walter Tools’ coated carbide grade within the Tiger‑tec Silver family; it offers balanced wear resistance and thermal stability for demanding drilling and boring operations. How does the chipbreaker B57 affect performance? The chipbreaker B57 shapes and breaks chips to improve evacuation and reduce the risk of recutting, contributing to more stable cutting conditions and consistent bore quality with this indexable insert. Is the corner radius suitable for finishing operations? Yes, the 0.3 mm corner radius provides a compromise between edge strength and surface finish, supporting improved durability without sacrificing the ability to achieve fine finishes. Which cutting conditions benefit most from this insert geometry? Applications with medium to high material removal rates in steel and cast iron, where chip control and edge stability are critical, benefit most from the rectangular insert geometry and its 7° clearance angle. Manufacturer: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
LCMX050203-B57 WKP35S Wendeplatten - Walter Tools
Combining the wear-resistant Tiger‑tec Silver coating with the WKP35S carbide grade, this insert delivers dependable machining performance for steel and cast iron applications. Take advantage of improved tool life and consistent chip formation for uninterrupted production; order directly via Metav Werkzeuge or consult the Metav technical team for application advice. LCMX050203-B57 WKP35S — Indexable drilling/boring insert for steel and cast iron, Walter Tools The LCMX050203-B57 WKP35S is a rectangular indexable insert designed for drilling and boring, optimised for machining steel (P) and cast iron (K) Tiger‑tec Silver coated carbide grade WKP35S Optimised for steel and cast iron machining Rectangular insert with 0.3 mm corner radius Chipbreaker B57 for controlled chip formation Reliable cutting performance from Tiger‑tec Silver The Tiger‑tec Silver coating combined with a coated carbide substrate provides a robust balance of wear resistance and thermal stability. This composition reduces flank and crater wear during continuous drilling cycles, which supports longer tool life and fewer index changes. The WKP35S grade is engineered for the typical heat and chip behaviour when machining steel and cast iron, so that cutting forces remain predictable and machine utilisation improves. Explaining the designation: P denotes suitability for steel, K for cast iron, ensuring the grade selection aligns with ISO 513 material groups and production planning. Predictable chip control and consistent surface finish Chip management is central to efficient drilling and boring. The B57 chipbreaker promotes short, controllable chips that help avoid build‑up and reduce risk of tool jamming in deep holes. With a 0.3 mm corner radius and a 7° clearance angle, the insert geometry supports stable cutting edges and consistent entry/exit behaviour, which in turn improves bore roundness and surface quality. The tolerance class M ensures dimensional consistency between inserts, simplifying replacement and reducing setup variability in series production. Lower operating costs through higher productivity Stable cutting edge life and reliable chip control translate into measurable process advantages: fewer tool changes, reduced machine downtime and more predictable batch throughput. The rectangular geometry and the WKP35S composition allow for repeatable performance across a range of cutting conditions, enabling tighter scheduling and a leaner inventory of tool grades. For production environments seeking to increase spindle uptime and reduce per‑part machining cost, the LCMX050203-B57 WKP35S presents a practical option that balances productivity and longevity. For tailored application recommendations or to secure Walter Tools Tiger‑tec Silver inserts for serial production, contact Metav Werkzeuge for specialist guidance and fast delivery. Technical data Article number: LCMX050203-B57-WKP35S-WALTER Product: Drilling/boring indexable insert Designation: LCMX050203-B57 WKP35S Manufacturer: Walter Tools UID: LCMX050203-B57-WKP35S-WALTER Core technical figures Corner radius: 0.3 mm Clearance angle: 7° Plate size: 05 Plate thickness: 02 Tolerance class: M Special features Grade: WKP35S Series: Tiger‑tec Silver Chipbreaker: B57 Applicable materials: Steel (P), Cast iron (K) Coating / substrate: coated carbide Execution: X Plate shape: Rectangular FAQ Which materials are suitable for this insert? The insert is specified for steel (P) and cast iron (K) machining; the WKP35S grade and Tiger‑tec Silver coating are matched to those material groups. How does the B57 chipbreaker influence drilling performance? The B57 chipbreaker produces short, controlled chips that reduce the risk of entanglement and improve evacuation in drilling and boring operations. What benefit does the 0.3 mm corner radius provide? A 0.3 mm corner radius enhances edge strength for interrupted cutting and helps maintain bore geometry while balancing cutting forces. What does tolerance class M mean for production? Tolerance class M indicates a medium grade of dimensional accuracy, supporting consistent insert interchangeability and predictable tool offsets in series runs. Is the WKP35S grade suitable for continuous production? Yes, WKP35S with the Tiger‑tec Silver coating is designed for stable cutting behaviour and extended tool life, making it well suited to continuous production environments. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only; there is no affiliation between our company and the named brands. The offered article is an original, factory‑new product of Walter Tools.
LCMX050203-B57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of high process reliability, versatile material capability and the Tiger·tec Gold PVD technology for consistent productivity in drilling and reaming operations. Order the insert directly via Metav Werkzeuge or contact the technical team for application advice. LCMX050203-B57 WSP45G Drill/Reaming Cutting Insert, Tiger·tec Gold – Walter Tools A LCMX050203-B57 WSP45G is a PVD-coated Tiger·tec Gold indexable insert designed for drilling and reaming tasks in demanding materials such as steel, stainless steel and heat‑resistant superalloys. Tiger·tec Gold PVD coating for durable edges Suitable for Steel, stainless steel and superalloys Rectangular form with 0.3 mm corner radius 7° clearance angle for stable cutting action Optimised cutting performance for production stability The Tiger·tec Gold PVD-coated carbide grade offers a balance between toughness and wear resistance, translating into stable flank wear and predictable tool life under varying cutting conditions. For production environments where cycle time and repeatability matter, this insert supports steady chip control thanks to the integrated B57 chipbreaker, reducing interruptions for rework and enabling smoother process planning. The combination of coating technology and grade selection promotes efficient heat resistance during interrupted cutting typical of drilling and reaming. Reliable material versatility reduces tool inventory Designed for ISO groups P, M and S, the insert handles unalloyed and alloyed steel, rostfreier Stahl (stainless steel) and high‑temperature alloys such as titanium and nickel‑based superalloys. The robust substrate and coating pairing minimise edge chipping when machining tough materials, so fewer different grades are required across jobs. This versatility lowers overall tooling stock and simplifies setup decisions without compromising component quality or surface finish. Geometry that supports secure engagement and repeatable positioning The rectangular plate with a 0.3 mm corner radius and a 7° clearance angle ensures reliable entry and sustained contact in drill pockets and reaming passes. The defined corner radius improves edge strength for holemaking, while the clearance angle reduces rubbing and heat build-up on the flank face. Together these geometric features contribute to repeatable hole quality and extended insert life, particularly in interrupted cuts or when operating at elevated spindle speeds. For deployment with Tiger·tec Gold inserts and to discuss optimum cutting parameters for specific workpieces, contact Metav Werkzeuge for targeted technical support and fast supply. Technical Data Article number: LCMX050203-B57-WSP45G-WALTER Product label: Bohr-/Aufbohrwendeschneidplatte LCMX050203-B57 WSP45G Walter Tools Manufacturer: Walter Tools Series: Tiger-tec Gold Grade: WSP45G Type: Drill/Reaming cutting insert Form: Rectangular Chipbreaker: B57 Facts Clearance angle: 7° Corner radius: 0.3 mm Plate size code: 05 Plate thickness code: 02 Tolerance class: M Special features PVD-coated carbide (Tiger·tec Gold) Material applications: Steel, stainless steel, superalloys (P / M / S) Execution: X ISO designation: LCMX050203-B57 WSP45G Insert designation without grade: LCMX050203-B57 FAQ What materials is this insert suitable for? The LCMX050203-B57 WSP45G insert is formulated for machining steel, stainless steel and heat‑resistant superalloys, as indicated by the P / M / S application groups. How does the Tiger·tec Gold coating benefit holemaking? Tiger·tec Gold provides improved wear resistance and thermal stability, which helps the insert maintain a stable cutting edge during drilling and reaming cycles. What is the significance of the 0.3 mm corner radius? A 0.3 mm corner radius increases edge strength at the point of engagement, reducing the risk of chipping and supporting consistent hole geometry under load. Is the B57 chipbreaker suitable for interrupted cuts? Yes, the integrated B57 chipbreaker is designed to promote controlled chip formation in drilling and reaming, aiding process reliability during interrupted cutting. Can the insert be used for high‑speed applications? The combination of a robust carbide substrate and Tiger·tec Gold coating supports elevated cutting speeds, with optimal parameters dependent on workpiece material and machine rigidity. The Walter AG (brand: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trade marks are mentioned for explanatory purposes only and do not indicate any affiliation between our company and the named manufacturers.
LCMX050203-B57 WXP40 WXP40 Wendeplatten - Walter Tools
Take advantage of the combination of reliable chip control and consistent edge life provided by the WXP40 grade; this enables efficient boring and reaming operations with predictable results. Order the LCMX050203-B57 WXP40 directly via Metav Werkzeuge or contact the consultants for application advice. LCMX050203-B57 WXP40 — Boring/Reaming Indexable Insert (Rectangular), Walter Tools — 7° clearance, 0.3 mm radius The LCMX050203-B57 WXP40 is a rectangular indexable insert designed for boring and light reaming tasks; its uncoated carbide grade offers straightforward performance where a robust, economical cutting edge is required. Rectangular insert with 0.3 mm corner radius 7° clearance for stable cutting geometry Uncoated carbide grade WXP40 Chipbreaker B57 for controlled chips Predictable metal removal for stable production The insert provides consistent cutting behaviour through its uncoated carbide WXP40 grade and the engineered chipbreaker B57, resulting in reduced vibration and clearer chip segmentation. Because the geometry includes a 0.3 mm corner radius and 7° clearance, the indexable plate supports steady engagement in boring cycles and helps to maintain hole size tolerance. The combination of these features makes the component especially suitable for series production where repeatability and minimal tool management are priorities. The description focuses on process outcomes rather than just item specs, helping planners evaluate production impact. Broad compatibility and clear application guidance Designed as a rectangular boring/reaming insert, the plate matches a range of holders and applications commonly found in general metalworking environments. The WXP40 grade is an uncoated hardmetal intended for a wide material spectrum; suitability should be checked against the specific product matrix for optimum results. The insert’s format and chip control features support use in both roughing and light finishing passes, improving machining stability and surface consistency without necessitating complex coolant strategies. Mounting, inspection and lifecycle considerations Installation is straightforward due to the standardized form and tolerance class M, enabling quick indexability and replacement during scheduled maintenance. The plate thickness and size coding (05 / 02) align with common clamping systems, while the rectangular form minimises setup errors. Regular inspection of the cutting edge and adherence to recommended cutting data will extend effective service life and reduce unplanned downtime. For optimal results, record machining parameters and edge-wear progression to refine feeds and speeds for repeated jobs. Contact Metav Werkzeuge for tailored cutting data or to discuss holder compatibility for Walter Tools inserts; specialists can advise on feed/speed settings and application-specific selection — info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: LCMX050203-B57-WXP40-WALTER Designation: LCMX050203-B57 WXP40 Product type: Bohr-/Aufbohrwendeschneidplatte Manufacturer: Walter Tools Core data Clearance angle: 7° Corner radius: 0.3 mm Plate size: 05 Plate thickness: 02 Tolerance class: M Chipbreaker: B57 Execution: X Materials & features Grade: WXP40 (uncoated carbide) Series: Walter Schneidstoffsorte - Serie offen Plate form: Rectangular Material information: Katalogabhängig Application note: Check suitability per product matrix FAQ What materials is this insert intended for? The LCMX050203-B57 WXP40 is specified as an uncoated carbide grade; suitability for specific materials should be verified against the product matrix and machining recommendations for the Walter Tools boring/reaming insert. How does the chipbreaker affect performance? The B57 chipbreaker on the insert promotes stable chip formation during boring and light reaming, improving process reliability and making chip evacuation more predictable for the Walter Tools plate. What does the tolerance class M indicate? Tolerance class M denotes the manufacturing precision of the insert pocket fit; it ensures consistent seating and repeatable positioning when used with compatible holders for the LCMX050203-B57 WXP40. Are there recommendations for cutting parameters? Recommended feeds and speeds depend on the workpiece material and machine rigidity; Metav Werkzeuge consultants can provide tailored cutting data for the Walter Tools insert based on the intended application. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabriksneue Waren des Herstellers.
LCMX050203-D57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the WKP25S grade to achieve consistent tool life and controlled chip formation in steel and cast iron operations; order directly via Metav Werkzeuge or request consultancy for process integration. LCMX050203-D57 WKP25S Drilling/Reaming Indexable Insert, Tiger·tec Silver — for steel and cast iron (Walter Tools) The LCMX050203-D57 WKP25S is a rectangular indexable insert designed for drilling and bore-enlargement tasks, offering robust chip control and optimised performance in steel and cast iron machining. Tiger·tec Silver coating technology WKP25S grade for steel and cast iron 7° relief angle for secure chip flow Rectangular shape with D57 chipbreaker Consistent performance through advanced coating The combination of the Tiger·tec Silver coating and the WKP25S grade provides a reliable basis for extended tool life and repeatable results when machining ferrous materials. The coating reduces abrasive wear and improves thermal resistance, which translates into stable cutting edges and fewer tool changes. For production environments where uptime and predictable component quality matter, this insert supports a consistent process window and reduced downtime. Geometry engineered for reliable chip formation A rectangular plate geometry paired with the D57 chipbreaker ensures predictable chip segmentation when working with P- and K-group materials. The modest corner radius of 0.3 mm and the 7° relief angle combine to deliver secure entry and controlled cutting forces, reducing vibration and improving hole integrity. Clear explanation: P stands for steel and K for cast iron under ISO 513, so the grade and chipbreaker are tuned specifically for the typical heat and chip characteristics of these materials. Process benefits and application guidance Using this insert in drilling or bore-enlargement cutters yields measurable advantages: improved surface finish, stable material removal rates and simplified tool selection across mixed batches of steel and cast iron. The insert’s construction supports efficient chip evacuation and reduces the risk of built-up edge in interrupted cuts. For operators seeking to increase throughput while keeping tolerances, the combination of coating, grade and chip control enhances both productivity and part quality. Contact Metav Werkzeuge today for tailored machining advice on Walter Tools LCMX050203-D57 WKP25S and to discuss availability and delivery; eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: LCMX050203-D57-WKP25S-WALTER Designation: LCMX050203-D57 WKP25S Product: Drilling/reaming indexable insert Brand: Walter Tools Series: Tiger·tec Silver Core dimensions and numbers Relief angle: 7° Corner radius: 0.3 mm Plate size: 05 Thickness code: 02 Chipbreaker: D57 Tolerance class: M Shape: Rectangular Grade: WKP25S Materials & special features Suitable for steel (P) Suitable for cast iron (K) Coating technology: Tiger·tec Silver Application: Drilling and bore enlargement Execution: X Material code: P / K FAQ What materials is this insert suitable for? The LCMX050203-D57 WKP25S insert is suitable for ISO group P (steel) and K (cast iron) machining thanks to the WKP25S grade and Tiger·tec Silver coating. How does the chipbreaker affect performance? The D57 chipbreaker on this Walter Tools drilling/reaming insert promotes controlled chip segmentation and reliable evacuation, improving surface quality and reducing recuts. What is the significance of the 0.3 mm corner radius? A 0.3 mm corner radius offers a balance between edge strength and cutting accuracy, helping to withstand cutting loads while maintaining hole geometry. Can this insert be used for interrupted cuts? Yes, the combination of the WKP25S grade and Tiger·tec Silver coating provides good resistance to abrasive conditions and is suitable for many interrupted drilling scenarios in steel and cast iron. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered item is original factory-new merchandise from the manufacturer, Walter Tools.
LCMX050203-D57 WKP35S Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Silver coating, the WKP35S carbide grade and a precise 0.3 mm corner radius for stable chip control and consistent results; order the insert via Metav Werkzeuge or consult their specialists for application support. LCMX050203‑D57 WKP35S — Drilling/Boring indexable insert with Tiger‑tec Silver, for steel & cast iron (Walter Tools) LCMX050203‑D57 WKP35S is a drilling and boring indexable insert engineered to deliver reliable chip control and high process security in steel and cast iron machining. Tiger‑tec Silver coated carbide grade WKP35S Optimised D57 chipbreaker for stable chips Designed for steel and cast iron machining Maximum cutting performance through advanced coating and grade The combination of the Tiger‑tec Silver coating and the WKP35S grade provides a balanced solution for demanding turning and drilling tasks in industrial workshops. The coated carbide construction allows for improved wear resistance and heat management during cutting, which translates into longer tool life and fewer interruptions for index changes. The enhanced surface finish of the coating supports higher cutting speeds while maintaining dimensional stability, so production runs achieve better throughput and reduced scrap rates. Geometry engineered to reduce rework and increase uptime With a 7° clearance angle and a 0.3 mm corner radius, this rectangular insert stabilises cutting forces and reduces vibration during entry and exit passes. The D57 chipbreaker is optimised for controlled, repeatable chip formation in mixed operations, limiting the risk of chip entanglement and tool damage. Such geometry contributes directly to consistent hole quality and repeatable tolerances, reducing downstream machining or rework and supporting predictable cycle times on CNC equipment. Clear application scope and straightforward workshop integration The insert is specified for ISO groups P and K, which means suitability for steel and cast iron workpieces; these classifications reflect typical heat and chip behaviour and help in selecting the right grade for the job. The medium tolerance class M and execution X indicate standard manufacturing precision and compatibility with common indexable‑insert toolholders. In practice, this leads to straightforward integration into existing tool sets and predictable performance across component batches. Contact Metav Werkzeuge today for tailored advice on application boundaries and to secure the Walter Tools LCMX050203‑D57 WKP35S insert for dependable drilling and boring production. Technical data SKU: LCMX050203‑D57‑WKP35S‑WALTER Article designation: LCMX050203‑D57 ISO designation: LCMX050203‑D57 WKP35S Grade: WKP35S Series: Tiger‑tec Silver Execution: X Tolerance class: M Material designation: P / K Numbers / Core technical data Clearance angle: 7° Corner radius: 0.3 mm Plate size: 05 Plate thickness: 02 Special features / Versions Coated carbide Chipbreaker: D57 Plate shape: Rectangle Suitable for steel Suitable for cast iron Brand: Walter Tools FAQ What materials is this insert suitable for? The LCMX050203‑D57 WKP35S insert is specified for ISO groups P and K, meaning it is suitable for machining steel and cast iron in typical industrial applications. How does the Tiger‑tec Silver coating benefit machining? The Tiger‑tec Silver coating on the WKP35S grade improves wear resistance and heat management, enabling higher cutting speeds and more consistent tool life compared with uncoated grades. What is the purpose of the D57 chipbreaker? The D57 chipbreaker promotes controlled chip formation and evacuation during drilling and boring operations, which reduces the risk of chip packing and enhances process reliability. Can this insert be used in standard toolholders? Yes. The rectangular form and execution X align with common indexable insert toolholder systems, making it compatible with many standard drilling and boring setups. How does the 0.3 mm corner radius affect hole quality? A 0.3 mm corner radius helps to distribute cutting forces and improve surface finish at the hole edge, contributing to repeatable hole geometry and reduced need for finishing passes. The Walter AG (brand appearance: Walter Tools) is a recognised manufacturer of precision cutting tools and solutions for metalworking. Protected trademarks and product names are the property of their respective owners. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com
LCMX050203-D57 WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and a compact 0.3 mm corner radius for reliable chip control and long tool life; the insert offers efficient drilling and reaming across steel, stainless steel and superalloys and supports productive, repeatable results—order directly via Metav Werkzeuge or consult our technical team for application data. LCMX050203-D57 WSP45G drilling/reaming indexable insert – Tiger‑tec Gold, Walter Tools A LCMX050203-D57 WSP45G indexable insert engineered for productive drilling and reaming in demanding materials such as steel, stainless steel and heat‑resistant superalloys. Tiger‑tec Gold PVD coating for long tool life Versatile for steel, stainless and superalloys Rectangular plate with 0.3 mm corner radius 7° clearance angle for stable cutting Higher productivity through coated‑carbide performance The WSP45G grade, part of the Tiger‑tec Gold family, combines a PVD coating with a tough carbide substrate to deliver improved wear resistance and extended tool life. This combination reduces unplanned tool changes and increases spindle uptime, which translates into measurable gains in throughput. The coating technology stabilises the cutting edge under heat and load, so the insert maintains consistent performance across longer production runs. Stable chip formation and cutting security for drilling tasks Designed with a dedicated chip‑breaker (D57) and a small corner radius (0.3 mm), the insert promotes predictable chip control during axial cutting operations. The geometry and the 7° clearance angle reduce the risk of built‑up edge when machining cohesive or heat‑prone alloys. For practical terms: more stable chips mean fewer interruptions, simpler coolant management and cleaner holes with reduced rework requirements. Broad material applicability reduces tool inventories With suitability for material groups P, M and S, the insert covers unalloyed and alloyed steel, stainless steel and heat‑resistant superalloys/titanium. This broad range allows consolidation of tool inventories and faster job changeovers. The grade is particularly suited to milling‑derived PVD technology adapted for drilling/reaming, offering a balance between toughness and hardness that copes with the thermal stresses typical of these workpiece families. Practical advantages for workshop and production use The rectangular plate format and compact dimensions ensure secure clamping and straightforward indexation. A nominal plate thickness and standardised size support compatibility with common drill/reamer toolholders. Specified tolerances and the recognised Walter Tools manufacturing standard provide predictable repeatability, helping planners and operators to schedule tool life and cutting data with confidence rather than guesswork. Discuss cutting data and best‑fit inserts with Metav Werkzeuge to align the LCMX050203‑D57 WSP45G insert to specific machines and process windows; contact Metav Werkzeuge for tailored recommendations and cutter setups via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: LCMX050203-D57-WSP45G-WALTER Designation: LCMX050203-D57 WSP45G Type: Bohr-/Aufbohrwendeschneidplatte Series: Tiger‑tec Gold Grade: WSP45G Execution: X Tolerance class: M Key measurements Plate size: 05 Plate thickness: 02 Corner radius: 0.3 mm Clearance angle: 7° Chip‑breaker: D57 Materials and special features Suitable for: steel (P), stainless steel (M), superalloys/titanium (S) Coating type: PVD‑coated carbide (Tiger‑tec Gold) Plate shape: Rectangular Application: drilling and reaming inserts FAQ Is this insert suitable for machining stainless and heat‑resistant alloys? The WSP45G grade is formulated for stainless steel (M) and superalloys/titanium (S) applications, providing stable cutting edges and controlled chip formation during drilling and reaming. What advantages does the Tiger‑tec Gold coating provide? The Tiger‑tec Gold PVD coating increases wear resistance and edge stability under thermal load, which extends tool life and supports consistent hole quality with the LCMX050203‑D57 insert. How does the 0.3 mm corner radius affect hole quality? A 0.3 mm corner radius helps to distribute cutting forces at the edge and reduces micro‑chipping, resulting in improved surface finish and dimensional stability in drilled holes. Can the insert be used in standard tooling systems? The rectangular format and standardised plate size facilitate use in common drill and reamer holders designed for indexable plates; verify holder compatibility with the plate designation LCMX050203‑D57 WSP45G. What cutting behaviour can be expected with the D57 chip‑breaker? The D57 chip‑breaker is designed for axial cutting operations and offers predictable chip control, particularly in materials that produce long or stringy chips, reducing the likelihood of recutting and improving process reliability. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
LCMX050203-D57 WXP40 Wendeplatten - Walter Tools
Take advantage of the combination of productive geometry, consistent tool life and clear mounting data: the uncoated WXP40 grade with 0.3 mm corner radius and 7° relief supports stable holemaking and precise rework. Order the LCMX050203-D57 WXP40 directly via Metav Werkzeuge or ask the consultants for cutting-data recommendations. LCMX050203-D57 WXP40 drilling/up‑boring indexable insert, 0.3 mm corner radius, 7° relief — Walter Tools LCMX050203-D57 WXP40 is a rectangular drilling and up‑boring indexable insert designed for productive holemaking and enlargement tasks in industrial turning and milling operations Uncoated carbide grade WXP40 0.3 mm corner radius 7° relief angle Rectangular insert, size 05 Chipbreaker D57 for chip control Predictable productivity through geometry The LCMX050203-D57 WXP40 combines a compact rectangular form with a defined corner radius of 0.3 mm and a 7° relief, delivering predictable cutting behaviour in holemaking. The uncoated carbide grade offers stable performance where coating is not required or where coolant and application parameters demand a bare substrate. These geometry choices contribute to extended edge life and consistent bore finish, reducing the need for frequent regrinds and improving process uptime. For production contexts, the coded plate size and thickness simplify insert selection and toolholder compatibility. Engineered chip control for consistent holes The integrated chipbreaker D57 is shaped to promote controlled chip formation during drilling and up‑boring, improving evacuation from the hole and lowering the risk of built‑up edge. Controlled chips reduce heat concentration at the cutting zone and support repeatable surface integrity and dimensional accuracy. The rectangular shape also aids stability in the holder, which in turn helps maintain concentricity in successive holes — a direct benefit for shops striving for reproducible quality rather than intermittent good results. Straightforward mounting and measurable tolerances The insert is supplied to tolerance class M, with clear identifiers for plate size 05 and thickness 02, enabling rapid selection and clamping in compatible tool systems. A consistent tolerance class reduces setup variation and contributes to first‑pass conformity on jigged and automated machines. The execution code X indicates the specific design variant; referencing these codes in tool lists and CAM setups shortens machine preparation and helps maintain process stability across batches. Material guidance and practical production advice The insert is offered in the WXP40 grade as an uncoated cemented carbide; suitability for specific workpiece materials should be verified against the manufacturer's product matrix before series production. In many cases the grade offers broad applicability, but final selection depends on heat generation, feed strategy and whether the task involves plain drilling or enlargement with interrupted cuts. Where process security is critical, pairing the insert’s geometry with optimised feeds and coolant strategy yields the best balance of productivity and tool life. Speak to Metav Werkzeuge to specify the LCMX050203-D57 WXP40 for the intended material and to obtain recommended cutting data and availability Technical data Article number: LCMX050203-D57-WXP40-WALTER Designation: LCMX050203-D57 WXP40 Manufacturer: Walter Tools Core specifications Relief angle: 7° Corner radius: 0.3 mm Plate size: 05 Plate thickness: 02 Tolerance class: M Features Series: Walter Schneidstoffsorte - Serie offen Grade: WXP40 (uncoated cemented carbide) Shape: Rectangular Chipbreaker: D57 Execution: X Material: Katalogabhängig Note: Check material suitability per product matrix FAQ Which materials is this insert typically suitable for? The LCMX050203-D57 WXP40 insert from Walter Tools is an uncoated cemented carbide grade; material suitability is broad but should be confirmed via the product matrix for specific steels, alloys or non‑ferrous materials. Is this insert intended for drilling, reaming or hole enlargement? This indexable insert is designed for drilling and up‑boring/enlargement operations; the rectangular form and chipbreaker D57 favour stable holemaking and controlled chip evacuation. How does the D57 chipbreaker benefit production processes? The D57 chipbreaker promotes short, manageable chips and improves evacuation from the hole, which reduces heat concentration and supports a consistent surface finish during series machining. What do the codes size 05 and thickness 02 indicate? Size 05 and thickness 02 are the plate dimensional identifiers that determine holder compatibility and clamping depth; the tolerance class M denotes the manufacturing tolerance band for reliable repeatability. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Trademarks and product names are the property of their respective owners. Protected trademarks and trade names are mentioned for explanation purposes only. There is no affiliation between Metav Werkzeuge and the mentioned brands. The offered item is an original, factory‑new product from the stated manufacturer.
LCMX050203-E57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of WKP25S grade and Tiger‑tec Silver coating for stable edge life and consistent chip control; the rectangular geometry with a 0.3 mm corner radius and a 7° clearance angle supports productive drilling and boring in steel and cast iron. Order the insert directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. LCMX050203-E57 WKP25S – drilling/boring indexable insert, Tiger‑tec Silver, Walter Tools The LCMX050203-E57 WKP25S is a rectangular indexable insert developed for drilling and boring operations in steel and cast iron, combining a 7° relief and a 0.3 mm corner radius for reliable chip control and repeatable edge stability Tiger‑tec Silver coating for extended tool life Suitable for steel (P) and cast iron (K) Chipbreaker E57 for consistent chip control Rectangular form with 0.3 mm corner radius High‑productivity performance for holemaking The coated cutting grade WKP25S within the Tiger‑tec Silver family is engineered for productive machining of ISO groups P and K. The combination of a wear‑resistant coating and a geometry optimised for interrupted or continuous cuts yields longer intervals between index changes and reduces unplanned downtime. By balancing thermal resistance and edge stability, the insert supports higher cutting speeds and steady material removal rates, making it suitable for series production where process reliability is crucial. The design therefore translates directly into measurable productivity gains on the shop floor. Controlled chip formation and improved surface quality Chip management is central to efficient holemaking; the integrated chipbreaker E57 shapes chips consistently, reducing entanglement and easing evacuation in deep or confined holes. The modest 0.3 mm corner radius combined with a 7° clearance angle helps maintain a robust cutting edge while limiting radial cutting forces, which in turn promotes better surface finish and hole accuracy. For operations where repeatability matters, this geometry reduces vibration and supports stable tool‑workpiece interaction, yielding predictable results across batches. Simple integration and process security The rectangular format and standard designation ensure straightforward insertion into compatible toolholders and drills. The insert’s coding (LCMX050203‑E57) follows common conventions for quick identification during tool setup and inventory management. Material compatibility—specified for steel (P) and cast iron (K)—provides clear guidance when selecting the grade for mixed production runs. With tolerance class M, the component meets regular interchangeability expectations, simplifying the qualification of the cutting edge in existing workflows and minimising setup time. Application recommendations and selection guidance For best results, match the insert geometry and chipbreaker to the chosen toolholder and the specific drilling or boring cycle. The WKP25S grade is particularly effective where a balance of wear resistance and toughness is required; it performs well in unalloyed and alloyed steels as well as in various cast iron grades. Operators seeking extended life under higher thermal loads will benefit from the Tiger‑tec Silver coating’s resistance to abrasive and thermal wear. When in doubt about holder compatibility or cutting data, consult process engineers to adapt feeds and speeds for the intended machine and clamping conditions. Contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to specify the optimal insert geometry and secure the LCMX050203‑E57 WKP25S from Walter Tools for immediate production upgrades Technical data Article number: LCMX050203-E57-WKP25S-WALTER Designation: LCMX050203-E57 WKP25S Manufacturer: Walter Tools Core dimensions Clearance angle: 7° Corner radius: 0.3 mm Plate size: 05 Plate thickness code: 02 Tolerance class: M Special features Series: Tiger‑tec Silver Grade: WKP25S Chipbreaker: E57 Plate form: Rectangular Material groups: P (steel), K (cast iron) Material code: P / K Execution: X FAQ What materials is this insert suitable for? The LCMX050203‑E57 WKP25S insert from Walter Tools is designed for ISO groups P and K, meaning it is suitable for machining steel and cast iron workpieces. How does the Tiger‑tec Silver coating benefit performance? The Tiger‑tec Silver coating on the LCMX050203‑E57 WKP25S enhances thermal and abrasive wear resistance, which extends tool life and maintains edge stability during productive holemaking. What is the purpose of the E57 chipbreaker? The chipbreaker E57 on this indexable insert controls chip form and evacuation, promoting consistent chips and reducing the risk of jamming during drilling and boring operations. How should the corner radius and clearance angle influence cutting data? The 0.3 mm corner radius and 7° clearance angle support a robust cutting edge with controlled forces; feeds and speeds should be adjusted to balance finish and tool life according to workpiece material and holder rigidity. Is this insert compatible with standard rectangular holders? The rectangular form and standard designation LCMX050203‑E57 indicate compatibility with commonly used rectangular toolholders designed for this insert geometry; verify holder specification before ordering. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered article is an original, brand‑new product from the manufacturer.
LCMX050203-E57 WKP35S Wendeplatten - Walter Tools
Benefit from the combination of robust Tiger·tec Silver performance, the WKP35S coated carbide grade and the E57 chipbreaker for reliable chip control and extended cutting life; the 7° clearance and 0.3 mm corner radius support stable engagement and predictable results. Order the insert directly via Metav Werkzeuge or request application advice from our consulting team. Bohr-/Aufbohrwendeschneidplatte LCMX050203-E57 WKP35S – Tiger·tec Silver, for Steel & Cast Iron (Walter Tools) The LCMX050203-E57 WKP35S is a rectangular indexable insert engineered for drilling and bore-widening operations, optimised for steel (P) and cast iron (K) applications with consistent wear resistance and chip control. Tiger·tec Silver coated carbide grade WKP35S Rectangular plate with 0.3 mm corner radius E57 chipbreaker for controlled chip formation Suited for steel (P) and cast iron (K) machining Enhanced precision and predictable cutting results The Tiger·tec Silver coating combined with the WKP35S carbide formulation offers a balanced mix of hardness and toughness that translates into consistent tool life on a variety of steels and cast irons. The coated grade is designed to manage the heat and abrasive wear typical of P and K groups, which reduces flank wear and preserves the effective cutting geometry over longer runs. This predictability supports tighter process windows and fewer tool changes, improving throughput and part quality. Stable chip control to reduce interruptions Built around the E57 chipbreaker, this rectangular insert promotes reliable chip formation and evacuation, particularly in interrupted or variable-cut conditions. The geometry reduces the risk of long, entangling chips and lowers the likelihood of machine stoppages. The small 0.3 mm corner radius helps protect the cutting edge during engagement while maintaining acceptable surface finish, making the insert suited to operations where both stability and finish are required. Application guidance and setup benefits The insert’s 7° clearance angle ensures gentle entry and steady cutting forces, which is advantageous for drilling and bore-widening tasks in a workshop or production environment. With a tolerance class of M and plate dimensions indicated by size 05 and thickness 02, the indexable plate fits common toolholders for these tasks and delivers repeatable positioning. For best results, match cutting parameters to the workpiece group (P for steel, K for cast iron) and monitor feed and speed to align with the insert’s wear behaviour; when in doubt, consult machining tables or request tailored recommendations to optimise tool life and part accuracy. Contact Metav Werkzeuge for tailored application advice on Walter Tools Tiger·tec Silver inserts and recommendations for machining steel and cast iron components Technical data SKU: LCMX050203-E57-WKP35S-WALTER Designation: LCMX050203-E57 WKP35S Type: Drill/boring indexable insert Brand: Walter Tools Core specifications Clearance angle: 7° Corner radius: 0.3 mm Plate size: 05 Plate thickness: 02 Tolerance class: M Series: Tiger·tec Silver Grade: WKP35S Applications & features Material applicability: P (steel), K (cast iron) Chipbreaker: E57 Plate form: Rectangular Execution/version: X Coated carbide grade; optimised for wear and heat resistance FAQ Which materials is this insert suitable for? The insert is suitable for steel (P) and cast iron (K) applications; the WKP35S grade and Tiger·tec Silver coating are specifically tuned for these material groups. What is the purpose of the E57 chipbreaker? The E57 chipbreaker improves chip control and evacuation during drilling and bore-widening, reducing interruptions and promoting consistent surface quality. How does the 7° clearance affect cutting? A 7° clearance reduces friction at the flank and provides gentle entry into the workpiece, which helps maintain edge life and stabilise cutting forces during operation. Is the insert compatible with standard toolholders? The plate dimensions (size 05, thickness 02) and tolerance class M align with common holders for drilling and boring applications; verification against the holder specification is recommended. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany, info@walter-tools.com Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanation. There is no affiliation between our company and the brands named. The offered item is an original, factory-new product of the manufacturer.
LCMX050203-E57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and a compact geometry for reliable chip control and consistent edge life; request expert advice from Metav Werkzeuge for application-specific recommendations or to order the inserts directly. LCMX050203-E57 WSP45G — Drilling/Boring Indexable Insert by Walter Tools, Tiger·tec Gold, 7° clearance The LCMX050203-E57 WSP45G is an indexable insert designed for drilling and boring operations, optimised for steel, stainless steel and heat-resistant alloys and built for consistent chip formation in demanding machining cycles Tiger·tec Gold PVD-coated grade WSP45G Suitable for steel, stainless steel and superalloys 7° clearance angle for stable cutting 0.3 mm corner radius for consistent edge life Extended tool life through high-performance coating The combination of the Tiger·tec Gold coating and the PVD technology delivers improved resistance to wear and built-up edge, which translates into longer tool life and fewer insert changes during production. PVD-coated carbide provides a wear-resistant surface while maintaining toughness at the core; this balance reduces downtime and improves overall machining economy. Explaining briefly, PVD (physical vapour deposition) forms a thin, hard layer that slows abrasion and helps maintain cutting-edge geometry under thermal and mechanical load. Broad material compatibility to reduce tool variants This insert is specified for the ISO groups P / M / S, meaning it is suitable for machining unalloyed and alloyed steel, rostfreier Stahl (stainless steel) and heat-resistant superalloys/titanium. Using a single grade for multiple workpiece groups cuts tooling complexity and minimises inventory, while offering consistent performance across typical production tasks. For operations where material changeovers occur frequently, the versatility of this grade supports predictable chip behaviour and reduces the need for frequent requalification of cutting tools. Precision geometry for repeatable cutting performance The rectangular insert geometry with a 0.3 mm corner radius and a 7° clearance angle is engineered to combine cutting-edge stability with reliable edge strength. The modest corner radius supports an even distribution of cutting forces and enhanced corner life, whereas the clearance angle helps prevent rubbing and reduces heat transfer to the flank face. These features contribute to stable cutting conditions, improved surface finish and reduced risk of built-up edge in continuous drilling and boring cycles. The insert format (size code 05, thickness code 02) enables compact toolholder integration and straightforward replacement during maintenance. Stable chip control and productive machining cycles Belonging to the Tiger·tec Gold series and specified as the WSP45G grade, the insert supports controlled chip formation and stable cutting edges in milling-derived drilling and boring applications. Its coated hardmetal composition is optimised for toughness and wear resistance, providing steady results across medium to high cutting speeds. For production environments aiming for predictable cycle times and high throughput, this insert offers the combination of coating technology, geometry and grade selection that favours process reliability and repeatable part quality. Contact Metav Werkzeuge to discuss the machining task and obtain tailored recommendations or supply of Walter Tools LCMX050203-E57 WSP45G indexable inserts for your production needs Technical data Article number: LCMX050203-E57-WSP45G-WALTER Designation: LCMX050203-E57 WSP45G Product type: Drilling/boring indexable insert Manufacturer: Walter Tools Series: Tiger·tec Gold Grade: WSP45G Shape: Rectangular Application groups: P / M / S Execution: X Tolerance class: M Core dimensions Clearance angle: 7° Corner radius: 0.3 mm Plate size: 05 Plate thickness: 02 Special features PVD-coated hardmetal (Tiger·tec Gold) Versatile for steel, stainless steel and superalloys Engineered for stable chip formation and edge life Rectangular insert geometry for drilling/boring use Suitable for productive milling-derived drilling cycles FAQ What materials can this insert machine effectively? The LCMX050203-E57 WSP45G insert is formulated for steel, rostfreier Stahl (stainless steel) and heat-resistant superalloys/titanium, corresponding to ISO groups P, M and S. How does the Tiger·tec Gold coating benefit machining? The Tiger·tec Gold PVD coating provides improved wear resistance and thermal stability, helping the LCMX050203-E57 WSP45G maintain cutting-edge geometry and extend service life under demanding conditions. What does the 0.3 mm corner radius mean for part quality? A 0.3 mm corner radius smooths cutting forces at the edge, enhancing edge robustness and supporting a consistent surface finish while reducing the likelihood of chipping in interrupted cuts. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
LCMX050203-E57 WXP40 WXP40 Wendeplatten - Walter Tools
Combine the E57 chipbreaker and 0.3 mm corner radius with the durable uncoated carbide grade WXP40 to achieve steady chip formation and extended edge life; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. LCMX050203-E57 WXP40 drilling/boring indexable insert — E57 chipbreaker, 0.3 mm corner radius — Walter Tools The LCMX050203-E57 WXP40 is an indexable insert engineered for drilling and boring operations, offering robust edge geometry and a chip control design suited to production environments. Uncoated carbide grade WXP40 E57 chipbreaker for stable chips 0.3 mm corner radius for edge strength 7° relief angle for controlled cutting Rectangular 05 form, plate thickness 02 Consistent chip control improves process reliability The combination of the E57 chipbreaker and optimised geometry delivers stable chip control, reducing the risk of clogging and erratic tool behaviour. Stable chips mean fewer interruptions and more uniform cycle times, which supports a measurable increase in productivity on repetitive drilling and boring tasks. Explanations: a chipbreaker modifies the chip flow to avoid long, stringy chips that can damage the workpiece or toolholder. Geometry and material choice for durable performance Built from uncoated carbide in the WXP40 class, the insert balances toughness and wear resistance for demanding machining. The 0.3 mm corner radius strengthens the cutting edge against mechanical shock, while the 7° relief angle helps maintain a controlled cutting action and reduce rubbing. These features combine to prolong cutting life and preserve surface quality in standard industrial cycles. Indexable design reduces operating costs and simplifies handling As an indexable insert, the component enables quick rotation or replacement of cutting edges without regrinding, lowering setup times and consumable handling. The tolerance class M ensures consistent seating and repeatable positioning in compatible toolholders; the rectangular 05 form and plate thickness 02 simplify inventory management by standardising spares. Fewer tool changes translate into a leaner production flow and reduced indirect costs. Application guidance and selection notes for secure machining Intended for drilling and boring applications, the insert performs best when matched to the correct toolholder and machining parameters; consult the product matrix to verify material suitability and recommended cutting data. The open Walter cutting-grade series indicates an uncoated carbide approach—check machining recommendations for workpiece materials and coolant conditions to obtain optimal results and surface finish. Contact Metav Werkzeuge for tailored machining recommendations and to source the Walter Tools LCMX050203-E57 WXP40 insert — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Article number: LCMX050203-E57-WXP40-WALTER SKU: LCMX050203-E57-WXP40-WALTER Designation: LCMX050203-E57 WXP40 Manufacturer: Walter Tools Product type: Drilling/boring indexable insert Execution: X Facts Relief angle: 7° Corner radius: 0.3 mm Plate form: Rectangular (05) Plate thickness: 02 Tolerance class: M Special features Chipbreaker: E57 Material: catalogue-dependent (uncoated carbide indicated) Grade: WXP40 (uncoated carbide) Series: Walter cutting-grade series – open Plate designation without grade: LCMX050203-E57 FAQ What machining tasks is this insert intended for? The insert is intended for drilling and boring operations; the LCMX050203-E57 WXP40 is optimised for such tasks when used in compatible toolholders and under recommended conditions. How does the E57 chipbreaker affect performance? The E57 chipbreaker promotes stable chip formation, reducing clogging and improving cycle consistency for the Walter Tools insert. Is WXP40 coated or uncoated, and what does that mean? WXP40 is specified as an uncoated carbide grade; this typically offers toughness and resistance to mechanical shock, suitable when coating is not required for lubrication or thermal protection. How should tool selection be validated for different workpiece materials? Material suitability must be checked against the detailed product matrix; confirm compatibility before machining to ensure the LCMX050203-E57 WXP40 meets the required performance. What does tolerance class M indicate for assembly? Tolerance class M denotes a medium precision fit for seating and positioning in standard toolholders, supporting repeatable indexing and predictable assembly behaviour. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Walter Tools: Brand names and trademarks are the property of their respective owners. They are mentioned for explanatory purposes only and do not imply any connection between our company and the named brands. The offered item is original, factory-new goods of the manufacturer.
LCMX050203-F57 WKP35S WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of durable Tiger‑tec Silver coating and a precise F57 chipbreaker for consistent productivity in steel and cast iron machining; secure reliable repeatability and long tool life with the WKP35S grade. Order directly via Metav Werkzeuge or consult our specialists for application advice. LCMX050203-F57 WKP35S drilling/boring indexable insert by Walter Tools — Tiger‑tec Silver coating, for steel and cast iron LCMX050203-F57 WKP35S is a rectangular drilling/boring indexable insert designed for machining steel and cast iron, delivering stable chip formation and extended cutting-edge life Tiger‑tec Silver coating for extended tool life Optimised F57 chipbreaker for reliable chip control Suitable for steel and cast iron machining Small 0.3 mm corner radius for fine finishing Increase machining throughput with a wear-resistant coating The WKP35S grade, applied to this insert, combines a coated cemented carbide substrate with the Tiger‑tec Silver technology to reduce flank and crater wear under continuous cutting conditions. For production environments that prioritise cycle time, this results in more consistent tool life and fewer unscheduled stops. The combination of a robust grade and an optimised coating supports higher material removal rates and maintains dimensional stability over longer tool runs, which improves machine utilisation and lowers per-part machining cost. Predictable chip behaviour for safer, faster operations The integrated F57 chipbreaker is configured to control short, broken chips commonly encountered in steel and cast iron turning and boring. Predictable chip formation reduces the risk of entanglement and workpiece damage while helping to maintain a clear cutting zone. The insert’s modest 0.3 mm corner radius supports a balance between edge strength and surface finish, enabling reliable edge life without sacrificing the ability to achieve acceptable component tolerances and improved finishing characteristics. Geometry and tolerance that support repeatable accuracy With a rectangular form and a tolerance class M, this indexable insert suits operations where consistent positioning and repeatability are required. The insert’s 7° free angle helps to reduce rubbing and heat generation at the cutting edge, which contributes to lower thermal loading and better dimensional control during extended cycles. These geometric traits make the plate well suited to standard drilling and boring tool holders where secure clamping and consistent seating determine process stability. Practical application guidance for workshop planning Designed for the ISO material groups P and K, the insert is suitable for both steel and cast iron workpieces, covering a broad range of everyday machining tasks in job shops and production lines. Selecting the WKP35S grade with the Tiger‑tec Silver coating is recommended when a compromise between wear resistance and edge toughness is required. For newcomers to indexable tooling: the chipbreaker designation and corner radius directly influence chip shape and surface finish, so choose the F57 geometry and 0.3 mm radius if a controlled, short chip and moderate finishing are priorities. Contact Metav Werkzeuge for tailored cutting-data recommendations or to specify the LCMX050203-F57 WKP35S insert for a particular application via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: LCMX050203-F57-WKP35S-WALTER Product type: drilling/boring indexable insert Series: Tiger‑tec Silver Grade: WKP35S Manufacturer: Walter Tools Core technical characteristics Free angle: 7° Corner radius: 0.3 mm Plate size: 05 Plate thickness: 02 Tolerance class: M Special features and material suitability Coating: Tiger‑tec Silver Chipbreaker: F57 Plate form: rectangular Material applicability: P (steel) / K (cast iron) Base material: coated cemented carbide Designation: LCMX050203-F57 WKP35S FAQ What materials is this insert best suited for? The insert is specified for steel and cast iron machining; the WKP35S grade and Tiger‑tec Silver coating are optimised for ISO groups P and K. How does the F57 chipbreaker affect machining? The F57 chipbreaker promotes short, controlled chips for safer chip evacuation and more reliable surface finish when using the LCMX050203-F57 WKP35S insert. What does the 0.3 mm corner radius mean for component finish? A 0.3 mm corner radius provides a compromise between edge strength and surface quality, helping to produce a consistent finish while protecting the cutting edge. Is this insert compatible with standard drilling/boring tool holders? The rectangular geometry and tolerance class M are intended for common indexable insert holders; correct clamping and seating are essential for repeatable performance. Which feature most influences tool life in continuous operation? The Tiger‑tec Silver coating combined with the WKP35S grade primarily determines wear resistance and thereby extends the interval between insert changes. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only; there is no connection between our company and the named brands. The offered item is an original, brand‑new product from the manufacturer.
LCMX050203-F57 WSP45G Wendeplatten - Walter Tools
Take advantage of a Tiger·tec Gold PVD-coated grade that delivers stable cutting and broad material capability; the WSP45G variety combines toughness with reliable edge life for demanding drilling and boring operations. Order directly via Metav Werkzeuge or consult our specialists for process-matching recommendations. LCMX050203-F57 WSP45G – Drill/Boring Indexable Insert, Tiger·tec Gold by Walter Tools, 7° relief The LCMX050203-F57 WSP45G is a rectangular indexable insert engineered for drilling and boring tasks, optimised for applications in Stahl, rostfreier Stahl and heat-resistant alloys where consistent chip control and edge stability are required. Tiger·tec Gold coated grade WSP45G Versatile for Stahl, rostfreier Stahl, alloys Rectangle format, size 05, thickness 02 7° clearance angle for stable cutting 0.3 mm corner radius for controlled chip flow High-performance cutting for demanding materials The coated cemented carbide grade from the Tiger·tec Gold family provides a combination of toughness and thermal resistance that benefits operations on Stahl, rostfreier Stahl and nickel- or cobalt-based superalloys. The result is stable chip formation and reduced risk of build-up on the cutting edge, which directly supports longer tool life and fewer interruptions in machining cycles. For production environments where consistency matters, this behaviour reduces rework and improves overall throughput. Coating and grade translate into process reliability The WSP45G coating system is designed to withstand the heat and mechanical load typical of holemaking operations in challenging materials. Its PVD-type layering offers abrasion resistance while maintaining a resilient core, which helps to preserve the cutting edge under transient thermal and mechanical stress. This combination means improved edge stability and more predictable wear patterns, enabling reliable tool-change planning and easier assessment of return on tooling investment. Precision geometry for consistent results Geometry choices — rectangular format, a 0.3 mm corner radius and a 7° relief angle — are selected to balance strength and chip control. The modest corner radius supports controlled engagement and good micro-geometry stability, while the relief angle reduces rubbing at entry and exit, promoting smoother penetration and exit conditions. These attributes contribute to repeatable hole quality and reduced risk of exit burrs, particularly in interrupted or variable-depth holemaking. Practical application and process guidance In practice, this insert performs best where a combination of mechanical strength and thermal resilience is required. The grade's versatility makes it suitable for batch production and mixed-material runs, where operators benefit from a single insert type that handles a range of components. When integrating into a machining strategy, consider moderate cutting parameters to begin with and monitor chip form; adjustments to feed can quickly optimise surface finish and tool life. For tailored recommendations and parameter settings, Metav Werkzeuge provides technical assistance to match the grade to the specific machine and material. For process-stable drilling with Walter Tools’ Tiger·tec Gold grade, contact Metav Werkzeuge for application-specific advice and fast supply coordination. Technical Data Article number: LCMX050203-F57-WSP45G-WALTER SKU: LCMX050203-F57 WSP45G Facts Relief angle: 7° Corner radius: 0.3 mm Tolerance class: M Plate size: 05 Plate thickness: 02 Special features Series: Tiger·tec Gold Grade: WSP45G Plate form: Rechteck (rectangular) Chipbreaker: F57 Suitable for: Stahl, rostfreier Stahl, heat-resistant superalloys and titanium (P / M / S) Execution: X Tolerant class: M FAQ What materials is this insert suitable for? The insert is designed for machining Stahl, rostfreier Stahl and heat‑resistant superalloys (P / M / S groups) as specified for the WSP45G grade. How does the Tiger·tec Gold coating benefit holemaking? The Tiger·tec Gold coating on this grade improves thermal resistance and wear behaviour, giving the insert enhanced edge stability and consistent chip control during drilling and boring. What is the impact of the 0.3 mm corner radius on surface finish? A 0.3 mm corner radius provides a balance between cutting-edge strength and surface quality, supporting stable engagement and reduced risk of micro-chipping at the edge. Which insert geometry features aid in burr reduction? The combination of a rectangular form, the specified corner radius and a 7° relief angle reduces rubbing and supports cleaner entry and exit, which helps to minimise exit burr formation. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
LCMX050203-F57 WXP40 Wendeplatten - Walter Tools
Take advantage of precise geometry and proven chip control to improve drilling and boring stability; the combination of the WXP40 uncoated carbide grade and the F57 chipbreaker delivers consistent material removal and predictable tool life. Order the insert directly via Metav Werkzeuge or request application advice from the technical consultants. LCMX050203-F57 WXP40 — drilling/boring indexable insert, rectangular, uncoated carbide by Walter Tools LCMX050203-F57 WXP40 is a rectangular indexable insert engineered for drilling and boring operations where predictable chip formation and stable cutting are required Uncoated carbide grade WXP40 Precision 0.3 mm corner radius 7° clearance angle for stable cutting Chipbreaker F57 for controlled chips Stable chip control for uninterrupted production The chipbreaker F57 is designed to manage swarf reliably, reducing the risk of jamming and minimising interruptions in batch production. With the insert's planned chip geometry, material evacuation becomes more consistent, which supports higher process stability and fewer cycle-time variations. The use of an uncoated carbide grade contributes to dependable cutting performance across a range of workpiece materials; machinability should be checked against the supplied product matrix to confirm suitability for specific alloys. Geometry that enhances edge life and surface consistency A 0.3 mm corner radius and a 7° clearance angle combine to produce a cutting edge geometry that balances robustness with surface finish. The modest corner radius improves resistance against edge chipping while maintaining acceptable cutting forces for many drilling and boring tasks, and the clearance reduces rubbing on the flank face. These features together help achieve repeatable component quality and reduce the frequency of index changes, supporting a leaner tool management approach. Practical selection and application benefits The rectangular format and the insert thickness 02 provide mechanical stability in toolholders designed for this size class, while the tolerance class M ensures interchangeability and consistent fit. As an indexable insert, it enables rapid edge replacement without regrinding, lowering downtime and tooling logistics. Technical consultancy is available for cutting-parameter recommendations and for matching the WXP40 grade to a particular workpiece material; this support aids decision-making for process optimisation and cost-effectiveness. For reliable drilling and boring performance choose Walter Tools inserts — contact Metav Werkzeuge for tailored application support and ordering at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: LCMX050203-F57-WXP40-WALTER Designation: LCMX050203-F57 ISO designation: LCMX050203-F57 WXP40 Product type: drilling/boring indexable insert Manufacturer: Walter Tools Facts Corner radius: 0.3 Clearance angle: 7° Thickness: 02 Size class: 05 Tolerance class: M Special features Grade: WXP40 (uncoated carbide) Chipbreaker: F57 Shape: rectangular Execution: X Series: Walter Schneidstoffsorte - Serie offen Material specification: Katalogabhängig FAQ What materials is this insert suitable for? The LCMX050203-F57 WXP40 insert uses an uncoated carbide grade; suitability depends on the workpiece and should be verified against the product matrix for the WXP40 grade. How does the chipbreaker F57 influence machining? The F57 chipbreaker promotes shorter, controlled chips during drilling and boring, improving swarf evacuation and supporting stable cycle times with the insert. What benefits does the 0.3 mm corner radius provide? A 0.3 mm corner radius increases edge strength and reduces the likelihood of chipping, which helps maintain surface quality during extended runs with the insert. Is this insert compatible with standard indexable drill holders? The rectangular format and tolerance class M make the insert suitable for holders designed for the 05 size class; correct holder matching ensures proper clamping and performance. Can the WXP40 grade be used without a coating? Yes; the WXP40 designation indicates an uncoated carbide grade designed for general cutting tasks, though specific material matches should be checked before application. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand presentation: Walter Tools), headquartered in Tübingen, is among the world’s leading manufacturers of precision tools for metalworking and forms part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only and do not imply any affiliation between our company and the named brands. The item offered is original, factory-new merchandise from the manufacturer.
LCMX06T204-B57 WKP25S Wendeplatten - Walter Tools
Take advantage of the proven Tiger‑tec Silver grade and WKP25S cutting material for stable chip formation and long tool life; the rectangular geometry with corner radius 0.4 mm and B57 chipbreaker ensures consistent surface quality when machining steel and cast iron. Order the LCMX06T204-B57 WKP25S directly via Metav Werkzeuge or consult our specialists for application advice. LCMX06T204-B57 WKP25S — Drill/Boring indexable insert, Tiger‑tec Silver for steel and cast iron | Walter Tools The LCMX06T204-B57 WKP25S is a rectangular indexable insert engineered for drilling and bore-opening operations, offering a combination of coating technology and geometry optimised for P and K material groups. Tiger‑tec Silver coating technology Suitable for steel and cast iron machining Rectangular insert, corner radius 0.4 mm Chipbreaker B57 for stable chip control Higher throughput thanks to a modern coated grade The combination of Tiger‑tec Silver and WKP25S carbide provides improved wear resistance and thermal stability, which translates into higher productivity for serial drilling and boring tasks. The coating reduces abrasion and helps maintain a sharp cutting edge under the cyclic heat loads typical of steel and cast iron operations. For process planners, this means fewer tool changes and a more predictable production rhythm, with measurable gains in machine uptime and component consistency. Stable chips and better surface finish for uninterrupted production The dedicated B57 chipbreaker, paired with a corner radius 0.4 mm and 7° clearance, controls chip formation during holemaking to avoid long, stringy swarf and minimise rework. Improved chip control reduces the risk of recutting and supports a consistently good surface quality in bore walls. This geometry is especially beneficial where chip evacuation is critical to cycle time and where surface integrity directly affects downstream assembly or heat-treatment steps. Predictable clamping and dimensional stability in machining centres The rectangular plate form in size 06 with T2 thickness and tolerance class M provides repeatable seating and stable clamping in modular toolholders. The defined tolerance and thickness support interchangeability across holders designed for this ISO designation, resulting in fewer setup deviations and consistent hole dimensions. This mechanical predictability is key to maintaining process capability in high-volume runs and simplifies tool inventory management. Seamless integration into production workflows Designed for holemaking in steel and cast iron, this indexable insert fits common drilling/boring tool systems and is suitable for automated machining environments. The combination of grade and geometry allows operators to balance cutting data for longer tool life or faster cycle times depending on the priority of the operation. For maintenance and process teams, the clear specification reduces trial-and-error and speeds up qualification of cutting parameters for specific batches or material lots. For stable, high‑productivity drilling applications choose the Walter Tools Tiger‑tec Silver grade and contact Metav Werkzeuge for tailored application advice or to request the LCMX06T204-B57 WKP25S via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: LCMX06T204-B57-WKP25S-WALTER Label: Bohr-/Aufbohrwendeschneidplatte LCMX06T204-B57 WKP25S Walter Tools Manufacturer: Walter Tools Product type: Drill/boring indexable insert Grade: WKP25S Series: Tiger‑tec Silver Execution: X ISO designation: LCMX06T204-B57 WKP25S Plate designation (without grade): LCMX06T204-B57 Facts Clearance angle: 7° Corner radius: 0.4 mm Insert size: 06 Thickness: T2 Tolerance class: M Special features Chipbreaker: B57 Plate form: Rectangular Material application: steel (P), cast iron (K) Suitable for drilling and bore‑opening operations Stable chip formation and long tool life FAQ What materials is this insert suitable for? The LCMX06T204-B57 WKP25S (Walter Tools) is designed for steel and cast iron applications, corresponding to ISO groups P and K. Which chipbreaker does the insert use and why is it important? The insert features a B57 chipbreaker; this geometry promotes reliable chip control and helps maintain consistent surface finish during drilling and boring. How does the Tiger‑tec Silver grade affect performance? The Tiger‑tec Silver coating on the WKP25S grade enhances wear resistance and thermal stability, extending cutting edge life under standard drilling conditions. What are the key dimensional characteristics to check for compatibility? Check the size 06 designation, T2 plate thickness and rectangular form; these determine correct seating in the corresponding toolholder and ensure the tolerance class M fit. Is this insert intended for high‑volume production? Yes, the combination of grade and geometry supports higher throughput and predictable tool life, making it suitable for repetitive drilling tasks in production environments. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.*
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com