LDMT08T204R-F57 WKP35S Wendeplatten - Walter Tools
High productivity and predictable tool life are achieved by the combination of the Tiger·tec Silver coating and the WKP35S grade with an optimised F57 chipbreaker; ideal where consistent machining of steel and cast iron is required. Order directly via Metav Werkzeuge or consult its specialists for application-specific recommendations. LDMT08T204R-F57 WKP35S milling insert — Tiger·tec Silver coated carbide for steel and cast iron, Walter Tools LDMT08T204R-F57 WKP35S is a rectangular milling insert engineered for productive face and shoulder milling of steel and cast iron components, combining a robust coated-carbide grade with a chipbreaker designed for controlled swarf evacuation Tiger·tec Silver coated carbide WKP35S Optimised for steel and cast iron machining 15° clearance angle for stable cutting 0.4 mm corner radius, rectangular format Increase throughput on P and K materials The WKP35S grade, applied in the Tiger·tec Silver series, is a coated carbide solution optimised for ISO groups P (steel) and K (cast iron). Its composition and coating technology enable higher cutting parameters while maintaining wear resistance, so material removal rates can be raised without sacrificing component quality. The F57 chipbreaker contributes to predictable chip formation, lowering the risk of workpiece damage and reducing unplanned downtime. For production contexts where repeatability and cycle-time reduction matter, this geometry-grade combination supports a more efficient machining process. Stable edge life and reliable surface results A 0.4 mm corner radius and 15° clearance angle provide a balance between strength and surface finish: the radius reduces edge chipping on interrupted cuts, while the clearance angle prevents rubbing at the flank, improving tool life and consistency. The insert’s rectangular format adds rigidity in the clamping pocket, which is particularly beneficial during heavy shoulder cuts. Tolerance class M and the defined plate thickness ensure interchangeability and repeatable performance across toolholder changes, helping to keep setup variance and scrap rates low. Geometry and handling explained for straightforward integration Designation LDMT08T204R-F57 gives immediate information for tooling planners: plate size "08", thickness T2, chipbreaker F57 and the rectangular outline. The practical result is straightforward selection for compatible cutter bodies and minimal adaptation in existing tool rigs. The coating reduces friction and heat at the cutting edge; for operators unfamiliar with coated-carbide grades, this means fewer edge failures under comparable cutting speeds and improved resistance to abrasive wear when machining cast materials. What this delivers to the production line In short, the combination of the Tiger·tec Silver coating and the WKP35S grade delivers process stability, lower variance in component finish, and extended intervals between index changes. The insert is well suited to mixed batches where both steel and cast iron are machined, offering a single-grade option to simplify inventory. Walter Tools’ engineering background supports reliable edge preparation and coating quality, contributing to predictable performance in serial production environments. Contact Metav Werkzeuge for cutting-parameter recommendations and toolholder compatibility for Walter Tools Tiger·tec Silver WKP35S inserts — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 Technical data Article number: LDMT08T204R-F57-WKP35S-WALTER Product: Milling insert LDMT08T204R-F57 WKP35S Manufacturer: Walter Tools Facts Clearance angle: 15° Corner radius: 0.4 mm Plate size: 08 Thickness: T2 Tolerance class: M Shape: Rectangular Special features Grade: WKP35S Series: Tiger·tec Silver Chipbreaker: F57 Material application: Steel (P) and Cast iron (K) Coating: Tiger·tec Silver (coated carbide) Execution: T FAQ Which materials is the insert suitable for? The LDMT08T204R-F57 WKP35S is specified for ISO material groups P (steel) and K (cast iron), making it suitable for a broad range of general structural steels and grey/ductile cast irons. What does the WKP35S grade offer? WKP35S is a Walter coated-carbide grade within the Tiger·tec Silver series; it emphasises wear resistance and stable chip formation for productive machining of steel and cast iron. What are the key geometry values to consider? Key values are a 15° clearance angle, 0.4 mm corner radius, rectangular plate shape and a plate size of 08 with thickness T2, which together define cutting behaviour and clamping stability. How does the F57 chipbreaker affect cutting? The F57 chipbreaker is designed to control chip shape and evacuation during medium to heavy machining; it supports continuous and interrupted cuts typical in steel and cast-iron operations. Is this insert recommended for stainless steel or high-temperature alloys? No specific approval for stainless steel or exotic alloys is provided in the data; the LDMT08T204R-F57 WKP35S is optimised for steel and cast iron and may not deliver the same performance on austenitic stainless steels or superalloys without parameter adjustments. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand: Walter Tools) is part of the Sandvik Group and is recognised for precision tools in metalworking. Trademarks and trade names are the property of their respective owners. The offered item is an original, factory-new product of the manufacturer.
LDMT08T204R-F57 WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of the Tiger·tec Gold coating and the WSP45G grade for durable, versatile milling performance; the insert’s 15° clearance and 0.4 mm radius deliver stable cutting and good surface finish. Order the LDMT08T204R-F57 WSP45G directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. LDMT08T204R-F57 WSP45G — Milling indexable insert, Tiger·tec Gold by Walter Tools The LDMT08T204R-F57 WSP45G is a rectangular milling indexable insert optimised for versatile milling in steel, stainless steel and heat‑resistant alloys. Tiger·tec Gold PVD coating Versatile for steel, stainless steel and superalloys 15° clearance angle for cutting stability 0.4 mm corner radius for fine surface finish Consistent machining performance for demanding materials The insert’s core advantage is the WSP45G grade combined with Tiger·tec Gold PVD coating, developed for toughness and temperature resistance. This composition supports secure chip formation and reduces built‑up edge when machining common engineering materials such as steel, stainless steel and superalloys. The result is more predictable tool life and fewer unplanned tool changes, which translates into higher throughput and reduced process variability in production environments where repeatable results are essential. Geometry tuned for reliable surface quality and process stability A 15° clearance angle and a 0.4 mm corner radius create a geometry that balances strength and finish quality. The slightly generous clearance improves flank contact behaviour, while the rounded cutting edge reduces chatter and supports consistent surface texture on each pass. The rectangular plate shape offers stable seating in appropriate toolholders and contributes to even load distribution across the cutting edge, which is particularly useful when face or shoulder milling under variable feed conditions. Optimised chip control and longer effective tool life The integrated F57 chipbreaker is designed to manage chips efficiently across a wide range of cutting parameters, promoting controlled evacuation and minimising recutting. Combined with the Tiger·tec Gold surface treatment, the insert shows improved wear resistance and reduced friction at the cutting zone. These factors help maintain a stable cutting edge for longer, lowering the frequency of index changes and supporting continuous, productive machining cycles with fewer interruptions. Practical fit in production workflows Tolerance class M and plate thickness T2 ensure compatibility with many common milling systems that accept this size and form. The insert’s specification supports flexible deployment from routine roughing to intermediate finishing passes when appropriately set up. For shops aiming to harmonise tool inventories, the insert’s suitability for the P / M / S material groups reduces the need for multiple specialised grades, simplifying tooling logistics and aiding fast process adjustments on multi‑material production runs. For reliable productivity with Walter Tools’ Tiger·tec Gold inserts, contact Metav Werkzeuge for tailored advice and rapid supply — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: LDMT08T204R-F57-WSP45G-WALTER Article designation: LDMT08T204R-F57 Label: Fräswendeschneidplatte LDMT08T204R-F57 WSP45G Walter Tools Manufacturer: Walter Tools Facts Clearance angle: 15° Corner radius: 0.4 mm Plate size: 08 Plate thickness: T2 Tolerance class: M Chipbreaker: F57 Special features Series: Tiger·tec Gold Grade: WSP45G (coated carbide) Coating: Tiger·tec Gold (PVD) Suitable materials: P / M / S (steel; stainless steel; superalloys / titanium) Plate shape: Rectangular FAQ What materials is this insert suitable for? The LDMT08T204R-F57 WSP45G is suitable for steel, stainless steel and heat‑resistant superalloys (P / M / S), owing to the toughness and heat resistance of the WSP45G grade. What does the F57 chipbreaker achieve? The F57 chipbreaker on this insert improves chip control and evacuation, reducing the risk of recutting and contributing to more consistent surface finishes during milling. How does the Tiger·tec Gold coating benefit production? The Tiger·tec Gold PVD coating reduces friction and enhances wear resistance, which helps extend effective tool life and supports higher productivity in continuous machining operations. What does the 0.4 mm corner radius mean for surface quality? A 0.4 mm corner radius provides a balance between edge strength and finish quality, offering smoother transitions on the workpiece and reduced tendency for edge chipping under moderate loads. Which tolerance and thickness specifications should be noted? This insert is supplied in tolerance class M with thickness T2, ensuring dimensional consistency for reliable clamping and repeatable cutting performance. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original, factory‑new goods from Walter Tools.
LDMT14T308R-D51 WKP25S Wendeplatten - Walter Tools
The combination of Tiger·tec Silver coating and the WKP25S grade delivers high wear resistance and stable chip control for reliable milling of steel and cast iron; the rectangular geometry with a 0.8 mm corner radius and 15° clearance angle ensures predictable edge life and surface finish. Order the insert directly via Metav Werkzeuge or consult our technical team for application advice. LDMT14T308R-D51 WKP25S Milling indexable insert (Tiger·tec Silver) by Walter Tools — for steel and cast iron, 15° clearance The LDMT14T308R-D51 WKP25S is a rectangular milling insert engineered for efficient machining of steel and cast iron components, combining a modern coated grade with geometry tuned for consistent chip formation and reproducible surface quality. Tiger·tec Silver coated for wear resistance Suitable for steel and cast iron machining Rectangular form with 0.8 mm corner radius 15° clearance angle for stable cutting conditions Durable coating for longer tool life and consistent productivity The combination of a modern coated carbide grade and the Tiger·tec Silver technology provides enhanced resistance to abrasive wear and thermal influences during interrupted cuts. This results in longer periods between indexings and fewer tool changes, increasing machine uptime and lowering process costs. The insert’s coating technology is optimised for the thermal and mechanical stresses typical when machining steel and cast iron, helping to maintain cutting-edge integrity under varying cutting data. Geometry designed for predictable chip control and surface finish A rectangular insert shape with a 0.8 mm corner radius and a defined 15° clearance angle produces stable contact conditions at the cutting edge, which supports reproducible surface quality and dimensional accuracy. The D51 chipbreaker geometry promotes controlled chip segmentation when cutting both continuous and interrupted sections, reducing the risk of built-up edge and improving swarf evacuation in demanding operations. These geometric features translate into fewer rejects and more consistent component finishes. Broad application range with straightforward process integration Classified for machining groups P and K, this grade is suitable for a wide range of unalloyed and alloyed steels as well as many cast-iron grades. The insert thickness and form make it compatible with common cutter bodies that accept LDMT-style plates, enabling straightforward upgrades in existing toolsets. Process planners benefit from the insert’s tolerance class M, which supports reliable seating and repeatable indexing within multi-edge milling systems. Stable performance through thoughtful design and material pairing The WKP25S composition balances toughness and wear resistance, which is particularly useful in mixed-production environments where materials and cutting conditions vary. The insert’s robust design, together with the coated surface, reduces edge chipping in interrupted cuts and supports longer life under elevated cutting speeds. For operations prioritising productivity and constant results, this insert offers a pragmatic combination of durability and process security. For machining tasks that demand a balance of wear resistance and predictable edge life, consider Walter Tools’ Tiger·tec Silver grade and contact Metav Werkzeuge for tailored recommendations and ordering assistance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: LDMT14T308R-D51-WKP25S-WALTER SKU: LDMT14T308R-D51-WKP25S-WALTER Designation: LDMT14T308R-D51 WKP25S Product type: Milling indexable insert Data Plate size: 14 mm Plate thickness: T3 Corner radius: 0.8 mm Clearance angle: 15° Tolerance class: M Special features Grade/series: Tiger·tec Silver Coating: coated carbide (WKP25S) Chipbreaker: D51 Geometry: rectangular form Material suitability: steel (P), cast iron (K) Execution: T FAQ What materials are best machined with this insert? The LDMT14T308R-D51 WKP25S insert by Walter Tools is intended for machining steel (P) and cast iron (K), making it suitable for a broad range of unalloyed and alloyed steels as well as many cast-iron grades. How does the Tiger·tec Silver coating benefit production runs? The Tiger·tec Silver technology on the WKP25S grade improves wear resistance and thermal stability, which extends tool life and supports more consistent cycle times across long production runs. Which chipbreaker is fitted and what is its advantage? This insert features the D51 chipbreaker, which promotes controlled chip segmentation and reliable evacuation, particularly helpful when switching between continuous and interrupted cutting tasks. Can this insert be used for finishing and roughing operations? Yes; the rectangular geometry with a 0.8 mm corner radius and the coated WKP25S grade allow for both finishing and light to medium roughing applications, depending on cutting data and toolholder rigidity. Is the insert compatible with standard LDMT cutters? The designation LDMT14T308R-D51 indicates compatibility with cutter bodies designed for LDMT-style plates; confirm seat and clamping details against the cutter manufacturer’s specifications. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
LDMT14T308R-D51 WKP35G Wendeplatten - Walter Tools
Take advantage of the proven combination of Tiger·tec Gold coating and the WKP35G grade for extended tool life and consistent chip control; the robust D51 chipbreaker and 0.8 mm corner radius support precise finishes in steel and cast iron. Order directly via Metav Werkzeuge or consult our experts for application-specific recommendations. LDMT14T308R-D51 WKP35G rectangular milling insert — Tiger·tec Gold, for steel and cast iron (Walter Tools) LDMT14T308R-D51 WKP35G is a rectangular milling indexable insert designed for productive finishing and medium-duty roughing in steels and cast irons Tiger·tec Gold coated for long tool life For steel (P) and cast iron (K) ISO groups 0.8 mm corner radius for precise finishing Durable coated grade for consistent performance The insert is made from a coated carbide grade WKP35G incorporated in the Tiger·tec Gold series, delivering improved wear resistance and stable cutting-edge performance. The combination of substrate and coating is engineered to balance toughness and hardness, reducing flank wear and extending usable life compared with uncoated grades. This results in fewer insert changes, more predictable machining cycles and improved overall process reliability in mixed-production environments. Geometry and chip control that improve surface quality With a rectangular plate form, a 15° clearance angle and a 0.8 mm corner radius, the geometry supports repeatable edge engagement and consistent contact conditions. The D51 chipbreaker is tuned for controlled chip formation in both short and occasional stringy chips typical of cast iron and various steels, reducing the risk of built-up edge and promoting a superior surface finish. The insert thickness T3 and tolerance class M ensure secure clamping and dimensional stability during interrupted cuts. Practical benefits for workshop productivity Designed for series machining, this insert lowers downtime through extended intervals between indexing and replacement. The grade’s capabilities for ISO groups P and K mean fewer tool changeovers when switching between steel and cast iron, simplifying tool inventory and program planning. The insert’s stable cutting characteristics support higher metal removal rates where process security matters, helping to sustain part quality and reduce rework in production batches. Choose Walter Tools’ Tiger·tec Gold LDMT14T308R-D51 WKP35G for reliable, repeatable machining — contact Metav Werkzeuge for purchasing guidance or application support via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: LDMT14T308R-D51-WKP35G-WALTER Article designation: LDMT14T308R-D51 WKP35G Manufacturer: Walter Tools Series: Tiger·tec Gold Core data Clearance angle: 15° Corner radius: 0.8 mm Plate size: 14 mm Thickness: T3 Tolerance class: M Special features Grade/coating: WKP35G (Tiger·tec Gold) Shape: Rectangular Chipbreaker: D51 Applicable materials: Steel (P), Cast iron (K) Execution: T FAQ What materials is this insert suitable for? The LDMT14T308R-D51 WKP35G from Walter Tools is designed for ISO groups P (steel) and K (cast iron), offering reliable performance across those material families. How does the Tiger·tec Gold coating benefit machining? The Tiger·tec Gold coating on the WKP35G grade improves wear resistance and thermal stability, which extends the insert life and supports consistent surface quality in steel and cast-iron applications. What is the purpose of the D51 chipbreaker? The D51 chipbreaker is configured to control chip form and evacuation for common chip types encountered when machining steel and cast iron, helping to avoid chip-related interruptions and improve finish. How does the 0.8 mm corner radius affect the result? A 0.8 mm corner radius offers a good compromise between cutting edge strength and surface finish, enabling precise finishing while maintaining edge robustness under moderate axial depths of cut. Is this insert suitable for interrupted cuts and heavy engagement? The combination of the WKP35G grade, Tiger·tec Gold coating and rectangular geometry provides robust performance in intermittent cutting conditions and supports process stability under varying engagement levels. Hersteller: Walter Tools. The Walter AG (branded as Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners and are mentioned here for explanation only. There is no legal affiliation between our company and the named brands. The offered item is an original factory-new product of the manufacturer.
LDMT14T308R-D51 WPP35G WPP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and a D51 chipbreaker for steady chip formation and extended tool life; the robust WPP35G grade supports productive, reliable steel machining — order directly via Metav Werkzeuge or consult our specialists for application advice. LDMT14T308R-D51 WPP35G milling indexable insert, rectangular, for steel — Walter Tools LDMT14T308R-D51 WPP35G is a rectangular milling indexable insert designed for productive machining of steel with a Tiger·tec Gold coated carbide grade Tiger·tec Gold coated carbide grade WPP35G Rectangular insert with 0.8 mm corner radius Chipbreaker D51 for stable chip control 15° clearance and tolerance class M Increase productivity with a durable, coated grade The combination of Tiger·tec Gold coating and the WPP35G grade provides a clear efficiency advantage in medium- to high-duty milling of steels classified under ISO P. The advanced coating improves thermal resistance and reduces flank wear, which translates into longer tool life and fewer index changes during production. This performance-oriented chemistry is aimed at shops seeking consistent cycle times and lower overall tooling costs; the coated carbide substrate preserves cutting-edge stability under the typical heat and chip-load conditions found in steel cutting. Precise geometry for predictable chip flow and surface quality The insert’s geometry — a rectangular form with a 0.8 mm corner radius and 15° clearance — together with the chipbreaker D51, supports controlled chip formation and reliable evacuation. This design reduces the risk of irregular chips that can compromise surface finish or tool life, and the tolerance class M ensures repeatable seating in standard milling bodies. For operations where part quality and process repeatability matter, the combination of chip control and defined edge geometry delivers measurable improvements in component consistency and finishing effort. Application range and handling guidance for workshop use Designed for machining steels (ISO P), the insert is specified with thickness T3 and size designation 14 for integration into compatible tool holders. Its coated carbide construction and the D51 chipformer make it suitable for a wide range of roughing and semi-finishing tasks where stable material removal and predictable flank wear are priorities. For process setup, match the insert to a suitable rectangular pocket cutter and follow manufacturer recommendations for feeds and speeds based on workpiece grade; Metav Werkzeuge’s technical team is available for application recommendations and cutting-parameter guidance to maximise performance and economy. For high-productivity steel milling with a Tiger·tec Gold grade, contact Metav Werkzeuge for availability and tailored application support: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data SKU: LDMT14T308R-D51-WPP35G-WALTER Designation: LDMT14T308R-D51 WPP35G Manufacturer: Walter Tools Series: Tiger·tec Gold Material group: P (steel) Grade: WPP35G Facts Relief angle: 15° Corner radius: 0.8 mm Size designation: 14 Thickness: T3 Tolerance class: M Special features Rectangular insert form Chipbreaker: D51 Coated carbide (Tiger·tec Gold) Suited for steel (ISO P) Robust grade for productive machining FAQ What materials is this insert designed for? This insert is engineered primarily for steel applications (ISO P); the WPP35G grade and Tiger·tec Gold coating target the heat and chip characteristics of steel. How does the D51 chipbreaker help in production? The D51 chipbreaker promotes consistent chip segmentation and evacuation, reducing the chance of entanglement and improving surface finish for milling operations using the LDMT14T308R-D51 WPP35G insert. What does tolerance class M mean for toolholders? Tolerance class M indicates a medium seating precision that ensures repeatable fitment and reliable clamping in compatible rectangular milling cutters, supporting consistent machining results. Can this insert be used for finishing passes? Yes; with its 0.8 mm corner radius and controlled geometry, the insert is suitable for semi-finishing and certain finishing passes depending on cutter setup and workpiece requirements. Is the insert suitable for high-speed machining? The Tiger·tec Gold coating enhances thermal resistance and wear control, making the insert a strong candidate for elevated cutting speeds where the workpiece and machine rigidity allow. Manufacturer: AB Sandvik Coromant; Mossvägen 10; 811 34 Sandviken; Sweden; support.coromant@sandvik.com Protected trademarks and product names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation. There is no affiliation between Metav Werkzeuge and the trademark owners. The offered item is original and factory new from the manufacturer.
LDMT14T308R-D51 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold PVD technology, a D51 chipbreaker and a compact 0.8 mm corner radius to achieve stable chip control and reliable edge life in a wide range of milling tasks; order the LDMT14T308R-D51 WSP45G insert directly via Metav Werkzeuge or contact the consultants for application advice. LDMT14T308R-D51 WSP45G – milling indexable insert, Tiger‑tec Gold, Walter Tools The LDMT14T308R-D51 WSP45G is a rectangular milling indexable insert designed for productive milling of steel, stainless steel and heat‑resistant alloys, combining a robust PVD grade with a targeted chipbreaker for dependable material removal. Tiger‑tec Gold PVD grade for longevity Suitable for steel, stainless and superalloys 15° relief angle for secure cutting action Rectangular form with 0.8 mm corner radius Fast, consistent milling performance for mixed materials The Tiger‑tec Gold grade is a PVD‑coated cemented carbide designed to balance toughness and wear resistance across diverse workpiece materials. In practice, this means the insert delivers consistent cutting behaviour when machining unalloyed or alloyed steel, ductile stainless steel and demanding superalloys/titanium. The D51 chipbreaker assists in forming controllable chips during interrupted and continuous milling, reducing the risk of edge build‑up and improving process stability. This combination supports higher machine uptime and more predictable cycle times for mixed production environments. Geometry tuned for stability and surface quality A 15° relief angle and a 0.8 mm corner radius provide a compromise between strength at the cutting edge and the ability to generate a smooth surface finish. The moderate corner radius increases edge resilience against mechanical shock, while the relief angle minimises rubbing and heat generation at the flank, which is especially beneficial when facing tough, heat‑resistant materials. These geometric choices contribute to extended tool life and fewer insert changes, supporting leaner tooling logistics. Practical benefits from the chipbreaker and plate form The rectangular plate format and D51 chipbreaker are engineered to manage chip flow effectively on a range of slotting and face‑milling operations. The chipbreaker geometry helps break long, stringy chips into manageable pieces, improving evacuation and reducing recutting risks. For workshops seeking straightforward set‑up, this results in fewer process interruptions and a reduced need for excessive coolant or manual chip handling during medium to heavy milling operations. Versatility through grade selection and application scope The WSP45G grade was developed as a versatile option for milling applications where a single grade is expected to perform across multiple material groups. Its PVD coating enhances thermal and adhesive wear resistance while retaining enough toughness to avoid premature chipping under variable cutting conditions. The insert’s suitability for the ISO material groups P, M and S makes it a logical choice for job shops and production facilities that run mixed batches and require a reliable, all‑round indexable solution. Contact Metav Werkzeuge today to discuss how the LDMT14T308R-D51 WSP45G can be integrated into existing toolholders and machining processes or to request application guidance from the technical consultants at Metav Werkzeuge. Technical Data Article number: LDMT14T308R-D51-WSP45G-WALTER Designation: LDMT14T308R-D51 WSP45G Brand: Walter Tools Series: Tiger‑tec Gold Grade: WSP45G Facts Relief angle: 15° Corner radius: 0.8 mm Insert size: 14 Thickness: T3 Tolerance class: M Special features Chipbreaker: D51 Plate form: Rectangular Coating technology: Tiger‑tec Gold (PVD coated cemented carbide) Material applicability: Steel (P), Stainless steel (M), Superalloys / Titanium (S) Application: Milling indexable insert FAQ What materials can this insert machine effectively? The LDMT14T308R-D51 WSP45G insert is specified for ISO groups P, M and S, meaning it is suitable for machining steel, stainless steel and heat‑resistant superalloys/titanium. What benefits does the Tiger‑tec Gold grade provide in milling? Tiger‑tec Gold is a PVD‑based coating and substrate combination that enhances wear resistance and thermal stability while retaining sufficient toughness; the grade supports reliable edge life across mixed milling applications. What do the D51 chipbreaker and 0.8 mm radius mean for process stability? The D51 chipbreaker produces short, controllable chips that improve evacuation and reduce recutting, while the 0.8 mm corner radius strengthens the cutting edge against impact and contributes to a consistent surface finish. Which cutter style accepts LDMT inserts? LDMT‑design inserts are intended for indexable milling cutters that accept LDMT‑format plates; the LDMT14T308R‑D51 WSP45G fits standard holders supporting this designation. Is the insert suitable for interrupted milling or shoulder milling? Yes, the combination of a robust PVD grade, rectangular plate form and the D51 chipbreaker offers good resistance to the impact and variable cutting forces typical of interrupted and shoulder milling. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and product names are the property of their respective owners. Brand names and protected designations are used solely for explanation and to indicate compatibility; there is no affiliation between our company and these brands. The offered item is original and factory‑new.
LDMT14T308R-D57 WKK25G Wendeplatten - Walter Tools
The combination of the Tiger‑tec Gold WKK25G coating and a rectangular geometry with a 15° relief and 0.8 mm corner radius delivers consistent performance when machining abrasive cast iron; this balance of tool life and process reliability supports productive milling operations. Order the insert directly via Metav Werkzeuge or consult our technical team for application-specific advice. LDMT14T308R-D57 WKK25G — Rectangular milling insert, Tiger‑tec Gold (Walter Tools) The LDMT14T308R-D57 WKK25G is a rectangular indexable milling insert engineered for productive machining of cast iron components, combining a coated carbide grade with a dedicated D57 chipbreaker for reliable chip control. Tiger‑tec Gold coated grade WKK25G Optimised for cast iron machining 15° relief for stable cutting geometry 0.8 mm corner radius for controlled edge strength Higher throughput with predictable tool life The Tiger‑tec Gold coating and the WKK25G carbide grade are formulated to resist abrasive wear typical of cast iron, providing a predictable wear curve that helps maintain cycle times and surface quality. This results in fewer unscheduled tool changes and a lower cost per part in serial production. The coating technology also supports a broad range of finishing and semi‑finishing passes while maintaining edge stability under intermittent cutting loads. Accurate chip control and surface consistency A rectangular insert form combined with the D57 chipbreaker promotes controlled, short chips when cutting cast iron, reducing the risk of chip entanglement and improving machine uptime. The 15° relief angle reduces rubbing on the flank face, while the 0.8 mm corner radius balances edge strength and surface finish. These geometric choices translate into more consistent component surfaces and fewer rework cycles in downstream operations. Robust performance across typical milling tasks Designed as a versatile solution for cast iron, the grade provides a compromise between wear resistance and toughness, enabling both roughing and finishing operations without rapid loss of cutting capability. The insert’s construction supports steady cutting forces and stable run‑out behaviour, which is particularly advantageous when producing components that demand repeatable dimensions and surface integrity under industrial throughput conditions. Application guidance and integration into production Suitable for conventional milling setups where cast iron is the primary material, the insert works well in slotting, face milling and light profile operations when paired with appropriate toolholders. For parameter selection, toolpath strategy and holder recommendations tailored to a specific machine or workpiece geometry, Metav Werkzeuge’s consultants can provide targeted support to ensure the insert is applied for maximum efficiency and component quality. For machining cast iron with Walter Tools' Tiger‑tec Gold inserts, contact Metav Werkzeuge for tailored application support and ordering at info@metav-werkzeuge.com or by telephone on +49 2822 7131930. Technical data Article number: LDMT14T308R-D57-WKK25G-WALTER Designation: LDMT14T308R-D57 WKK25G Product type: Milling insert (indexable) Manufacturer: Walter Tools Facts Insert size: 14 mm Thickness: T3 Relief angle: 15° Corner radius: 0.8 mm Chipbreaker: D57 Tolerance class: M Version: T Special features Series: Tiger‑tec Gold Grade: WKK25G (coated carbide) Shape: Rectangular Material application: Cast iron Coated for abrasive wear resistance FAQ What materials is this insert suitable for? This insert is designed primarily for machining cast iron, using the WKK25G grade and Tiger‑tec Gold coating to handle abrasive workpiece conditions. What is the purpose of the D57 chipbreaker? The D57 chipbreaker produces short, controlled chips in cast iron, improving chip evacuation and reducing the risk of re‑cutting or chip jams during milling. Can this insert be used for finishing passes? Yes, the combination of the 0.8 mm corner radius and the coated grade allows for semi‑finishing to finishing operations on cast iron components with stable surface results. What does tolerance class M indicate? Tolerance class M specifies the dimensional tolerance band for the insert, ensuring predictable fit and repeatability in precision toolholder systems. Is the LDMT14T308R‑D57 WKK25G coated? Yes, this insert is supplied in the Tiger‑tec Gold coated carbide grade WKK25G, which is formulated for improved abrasion resistance when machining cast iron. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes and do not imply any affiliation between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer (Walter Tools).
LDMT14T308R-D57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, the WKP25S grade and precise geometry for reliable milling in steel and cast iron; this insert delivers consistent chip control and long tool life. Order the LDMT14T308R-D57 WKP25S milling insert directly via Metav Werkzeuge or ask our consultants if needed. LDMT14T308R-D57 WKP25S rectangular milling insert, Tiger·tec Silver – Walter Tools The LDMT14T308R-D57 WKP25S is a rectangular milling insert engineered for productive machining of steel and cast iron, combining a wear-resistant coating with a chipbreaker designed for secure material removal. Tiger·tec Silver coated carbide grade WKP25S Optimised chip control D57 chipbreaker 15° relief angle for secure cutting Rectangular form with 0.8 mm corner radius Consistent cutting performance for steel and cast iron The combination of the Tiger·tec Silver coating and the WKP25S carbide grade is optimised for typical heat loads and abrasion encountered when machining steel and cast iron. The coating enhances wear resistance and reduces flank wear, which increases process stability and extends tool life. For production environments this means fewer tool changes and more predictable component quality. The designation for workpiece groups P (steel) and K (cast iron) indicates the insert's intended material range and helps selecting the correct geometry for catalogue- or job-specific applications. Geometry that improves strength and surface quality A rectangular plate with a 0.8 mm corner radius and a 15° relief angle balances edge robustness with clearance during cutting. The modest corner radius increases edge strength for interrupted cuts and supports longer life without compromising finishing capability. The D57 chipbreaker actively shapes and breaks chips, reducing chatter and evacuation issues, which in turn lowers the risk of rework. With a plate thickness of T3 and tolerance class M, the insert offers reliable seating accuracy and repeatable clamping behaviour on toolholders adapted to this geometry. Productivity, handling and process reliability Designed as an indexable solution, the insert reduces setup time and allows rapid rotation to fresh cutting edges, supporting continuous production. The engineered grade and chip control cater to both roughing and semi-finishing operations depending on cutter geometry, enabling efficient material removal rates and consistent component tolerances. Walter Tools' series is known for stable edge life and process security; when paired with a suitable cutter body and cutting data, the insert contributes to lower unit costs and predictable cycle times. If clarification on suitable cutter bodies or cutting parameters is required, technical advice is available from Metav Werkzeuge. For high-demand milling in steel and cast iron, specify the Walter Tools LDMT14T308R-D57 WKP25S with Tiger·tec Silver through Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 for application advice and availability Technical data SKU: LDMT14T308R-D57-WKP25S-WALTER Article: LDMT14T308R-D57 WKP25S Product type: milling insert Brand: Walter Tools Facts Relief angle: 15° Corner radius: 0.8 mm Plate size: 14 mm Plate thickness: T3 Tolerance class: M Chipbreaker: D57 Special features Coating: Tiger·tec Silver Grade: WKP25S (coated carbide) Suitable workpiece groups: P (steel), K (cast iron) Plate form: rectangular Series: Tiger·tec Silver FAQ Which materials are best machined with this insert? The LDMT14T308R-D57 WKP25S insert is formulated for steel (P) and cast iron (K); the Tiger·tec Silver coating and WKP25S grade optimise wear behaviour for these groups. What does the D57 chipbreaker do in practice? The D57 chipbreaker breaks and guides chips to improve evacuation and reduce surface damage; this leads to more stable cutting and fewer interruptions during long cycles with the LDMT14T308R-D57 WKP25S insert. How does the 0.8 mm corner radius affect machining? A 0.8 mm corner radius increases edge strength and improves resistance to chipping in interrupted cuts while still allowing good surface finish in semi-finishing applications with the same insert. Is the insert suitable for finishing passes? Depending on cutter geometry and cutting data, the LDMT14T308R-D57 WKP25S can be used for semi-finishing and certain finishing tasks; the grade and chip control support consistent surface quality under appropriate feeds and speeds. What does tolerance class M mean for mounting? Tolerance class M indicates a medium dimensional tolerance that ensures reliable seating and repeatable clamping accuracy when paired with matching toolholders, supporting consistent tool performance. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer.
LDMT14T308R-D57 WKP35G Wendeplatten - Walter Tools
Benefit from a combination of robust wear resistance, stable chip control and a geometry designed for repeatable surface finish; the result is reliable, productive milling in steel and cast iron applications. Order the inserts directly via Metav Werkzeuge or contact the consultants for application-specific advice. LDMT14T308R-D57 WKP35G milling insert – Tiger·tec Gold, for Stahl and Gusseisen by Walter Tools The LDMT14T308R-D57 WKP35G is a rectangular indexable milling insert designed for medium- to heavy-duty machining of Stahl and Gusseisen, offering a balance of wear resistance and consistent chip control. Tiger·tec Gold coating for extended tool life Coated carbide grade WKP35G for steel and cast iron Optimised D57 chipbreaker for predictable chips Rectangular insert with 0.8 mm corner radius Faster throughput through a wear-resistant grade The Tiger·tec Gold technology and the WKP35G coated carbide grade deliver measurable advantages in process stability and tool life. The multi-layer coating and substrate combination reduce abrasive and adhesive wear during interrupted and continuous cuts, which leads to longer intervals between tool changes and a lower cost per component. For production environments where reproducible performance is critical, the insert’s engineered coating supports consistent cutting-edge behaviour across batches and work shifts. Predictable surface quality and edge control The geometry, including the chipbreaker D57, 0.8 mm corner radius and 15° clearance, has been developed to produce stable chips and minimise vibration during milling. The rectangular form provides a secure seating in holders and assures repeatable contact conditions, which translates into more consistent surface finishes and dimensional accuracy. Operators benefit from clearer machining windows: fewer unexpected tool failures and more predictable scrap rates mean improved overall equipment effectiveness. Application suitability and economical handling Designed for the ISO P and K groups, the insert is especially effective on Stahl (unalloyed and alloyed steels) and Gusseisen (cast iron). The T3 thickness and the plate geometry support robust clamping and resistance against edge chipping. Choosing the correct feed and depth of cut in line with machine rigidity and workpiece material will extract the best performance; for mixed-batch processing the grade’s broad applicability helps reduce tool inventory while maintaining productivity. For tailored recommendations on cutting parameters or holder compatibility, technical consultation is available. Contact Metav Werkzeuge for precise application advice and availability of Walter Tools Tiger·tec Gold WKP35G inserts — phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data SKU: LDMT14T308R-D57-WKP35G-WALTER Article designation: LDMT14T308R-D57 WKP35G Product type: Milling insert (indexable) Manufacturer: Walter Tools Facts Clearance angle: 15° Corner radius: 0.8 mm Plate form: Rectangular Plate size: 14 Thickness: T3 Chipbreaker: D57 Tolerance class: M Special features Grade: WKP35G (Tiger·tec Gold, coated carbide) Material compatibility: Stahl (P), Gusseisen (K) Execution: T Series: Tiger·tec Gold Axial enrichment: Series information included FAQ Which workpiece materials are suitable for this insert? The LDMT14T308R-D57 WKP35G insert is intended for machining Stahl (ISO group P) and Gusseisen (ISO group K); the WKP35G grade balances resistance against abrasive wear on cast components and heat-related wear on steels. What effect does the 0.8 mm corner radius have on results? A 0.8 mm corner radius increases edge robustness and improves surface finish during interrupted cuts; the rounded edge reduces the risk of chipping compared with smaller radii while maintaining good dimensional control. How does the D57 chipbreaker help in milling? The chipbreaker D57 promotes controlled chip formation and evacuation, lowering the likelihood of chip entanglement and contributing to consistent cutting forces and surface quality during milling of Stahl and Gusseisen. Is the WKP35G grade suitable for mixed production runs? Yes; the WKP35G coated carbide grade is designed for broad applicability across steel and cast iron, which helps reduce the number of grades required in mixed-batch production while maintaining wear resistance. Which insert features ensure repeatable seating and stability? The rectangular insert form, the specified T3 thickness and a standardised geometry (LDMT14T308R-D57) provide stable seating in matched toolholders, which is essential for repeatable machining and predictable tool life. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered article is an original, factory-new product of the manufacturer Walter Tools.
LDMT14T308R-D57 WPP35G WPP35G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold wear resistance, a 0.8 mm nose radius for consistent surface finish and a geometry tailored for efficient steel machining; order directly via Metav Werkzeuge or consult the team for application advice. LDMT14T308R-D57 WPP35G rectangular milling insert — Walter Tools (Tiger·tec Gold, 0.8 mm radius) The LDMT14T308R-D57 WPP35G is a rectangular milling insert designed for robust and productive machining of steel in general-purpose milling and slotting operations. Tiger·tec Gold coating for extended tool life Optimised for steel machining (ISO group P) 0.8 mm nose radius for reliable surface quality 15° relief angle for stable chip formation Increased productivity through geometry and grade optimisation The rectangular insert combines a proven cutting edge geometry with a high-performance coated carbide grade to deliver measurable productivity gains when cutting steel. The combination of the WPP35G grade and the chipbreaker D57 promotes stable chip formation and consistent cutting forces, which reduces tool changes and downtime. For workshops aiming to raise throughput without sacrificing component quality, this insert offers a practical route to lower tooling cost per part while maintaining machining stability. Coating technology that prolongs service life Equipped with the Tiger·tec Gold coating, the insert provides enhanced wear resistance under the thermal loads typical for steel machining. The coating works together with the coated carbide substrate to withstand abrasive and adhesive wear mechanisms, extending tool life and maintaining dimensional consistency. This results in fewer interruptions for index changes and a more predictable process window, supporting leaner production and planning in busy machining environments. Geometry designed for surface finish and cutting stability A 0.8 mm nose radius balances finish quality and edge strength, delivering good surface integrity on milled faces without increasing cutting forces excessively. The 15° relief angle reduces rubbing and supports clean engagement into the material, while the rectangular form ensures repeatable seating and indexing in standard toolholders. These geometric features contribute to reliable edge life and reproducible part quality, particularly on medium to heavy roughing and semi-finishing passes in steel. Practical application notes and material scope The insert is classified for ISO group P, making it suitable for a wide range of unalloyed and alloyed steels encountered in general engineering. The WPP35G grade provides a balance between wear resistance and toughness, suitable for mixed batches or variable production runs. Presented in a compact format with a clear chipbreaker designation, it integrates easily into existing tool setups and supports stable chip control across typical feed and speed ranges for steel machining. Contact Metav Werkzeuge for tailored machining recommendations and current stock information for Walter Tools Tiger·tec Gold inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: LDMT14T308R-D57-WPP35G-WALTER Designation: LDMT14T308R-D57 WPP35G Product type: Milling insert (rectangular) Manufacturer: Walter Tools Facts Plate size: 14 Thickness: T3 Nose radius: 0.8 mm Relief angle: 15° Chipbreaker: D57 Tolerance class: M Special features Series: Tiger·tec Gold Grade: WPP35G (coated carbide) Suitable for: Steel (ISO group P) Plate shape: Rectangular Typical applications: General milling, slotting, semi-finishing FAQ What materials is this insert suited for? The LDMT14T308R-D57 WPP35G is formulated for machining steel and is assigned to ISO material group P for a broad range of unalloyed and alloyed steels. How does the Tiger·tec Gold coating affect performance? The Tiger·tec Gold coating on this insert reduces abrasive and adhesive wear, improving edge life and contributing to more consistent part quality during extended milling cycles. What surface finish can be expected with a 0.8 mm nose radius? A 0.8 mm nose radius offers a balance between finish and edge strength; expect reliable surface integrity suitable for semi-finishing and many finishing operations, depending on cutting parameters. Is the chipbreaker D57 suitable for varying feed rates? The chipbreaker D57 is designed to support stable chip formation across common feed ranges for steel machining, helping to prevent built-up edge and to ease chip evacuation. Which production tasks benefit most from this insert? This rectangular insert is particularly effective for productive roughing and semi-finishing operations in steel where tool life and process stability are priorities. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is among the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanation only; there is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
LDMT14T308R-D57 WSM35G Tiger-tec Gold Wendeplatten - Walter Tools
Take advantage of high process security and extended edge life provided by the Tiger·tec Gold grade and the WSM35G coating, together with precise chip control from the D57 chipbreaker; order the LDMT14T308R-D57 WSM35G insert directly via Metav Werkzeuge or consult the technical team for application advice. LDMT14T308R-D57 WSM35G rectangular indexable milling insert by Walter Tools — Tiger·tec Gold, for stainless steels and superalloys LDMT14T308R-D57 WSM35G is a rectangular indexable milling insert designed for demanding machining of rostfreie Stähle and heat-resistant superalloys, combining a robust grade with an optimised chipbreaker for stable production. *Tiger·tec Gold coating for heat resistance *Optimised chipbreaker D57 for stable chips *0.8 mm corner radius for accurate edge form *Suitable for stainless steels and superalloys Consistent performance in tough materials The combination of the Tiger·tec Gold coating and the WSM35G grade gives the insert a high tolerance to thermal and mechanical stress, which directly improves tool life when machining stainless steels and superalloys. The coating reduces friction and protects the cutting edge at elevated temperatures, so the process runs with fewer interruptions and a reduced need for regrinding. This leads to measurable productivity gains and a lower cost per part in continuous production environments. Predictable chip control and surface quality The D57 chipbreaker is optimised to produce short, controllable chips with the chosen geometry and edge prep, decreasing the risk of built-up edge and improving surface finish. The 0.8 mm corner radius provides a consistent edge form that balances strength with dimensional accuracy; the result is reliable component geometry and a reduced need for secondary operations. For shops aiming to improve first-pass yield, the insert’s chip management offers a tangible advantage. Easy integration with standard toolholders The rectangular insert format and designation LDMT14T308R-D57 correspond to common milling cutter bodies, simplifying tooling logistics and changeover. With a clearance angle of 15° and thickness code T3, the insert fits typical milling assemblies while the tolerance class M supports reproducible positioning in multi-insert cutters. This compatibility helps to shorten setup times and ensures repeatable cutting conditions from batch to batch. Process security and application scope Engineered for demanding jobs, the grade supports machining of rostfreie Stähle and high-temperature alloys where heat resistance and edge stability are critical. The result is a more stable cutting process and consistent surface integrity, which is particularly relevant for aerospace, energy and medical component manufacturing. Backed by Walter Tools’ portfolio, the insert contributes to predictable cycle times and fewer unplanned tool changes. For reliable supply and application guidance on Walter Tools Tiger·tec Gold inserts such as LDMT14T308R-D57 WSM35G, contact Metav Werkzeuge and request technical consultation or ordering support via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: LDMT14T308R-D57-WSM35G-WALTER Designation: LDMT14T308R-D57 Full ISO designation: LDMT14T308R-D57 WSM35G Manufacturer: Walter Tools Series: Tiger·tec Gold Grade: WSM35G Material group: S / M Shape: Rectangular Numbers / Core technical data Size: 14 mm Thickness: T3 Corner radius: 0.8 mm Clearance angle: 15° Tolerance class: M Special features / Versions Chipbreaker: D57 Execution: T Coating technology: Tiger·tec Gold Suitable for: rostfreie Stähle and heat-resistant superalloys Plate form: Rectangular FAQ What applications is this insert suitable for? This LDMT14T308R-D57 WSM35G insert by Walter Tools is intended for machining rostfreie Stähle and heat-resistant superalloys where thermal stability and edge life are required. How does the D57 chipbreaker affect machining? The D57 chipbreaker on the insert promotes short, controlled chips and improves surface quality while reducing the tendency for built-up edge during interrupted or continuous cuts. What does the designation T3 and 14 mean for tooling? T3 denotes the plate thickness code and 14 refers to the insert size; these ensure compatibility with matching milling cutter bodies and correct clamping in the toolholder. Can this grade handle high cutting speeds? The Tiger·tec Gold technology used in WSM35G is engineered to withstand higher thermal loads, making the insert suitable for elevated cutting speeds in difficult-to-machine materials. Is the corner radius appropriate for finishing operations? The 0.8 mm corner radius provides a robust cutting edge while still allowing good surface finish, making the insert suitable for semi-finishing and many finishing tasks depending on the application. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned solely for explanatory purposes. There is no connection between our company and the mentioned brands. The offered item is original, brand-new goods from the manufacturer.
LDMT14T308R-D57 WSP45G WSP45G Wendeplatten - Walter Tools
Combine the Tiger‑tec Gold coating with the versatile WSP45G grade and the D57 chipbreaker for consistent chip control and reliable edge life; order the LDMT14T308R‑D57 WSP45G directly via Metav Werkzeuge or consult our technical team for application advice. LDMT14T308R-D57 WSP45G rectangular milling insert — Tiger‑tec Gold, D57 chipbreaker — Walter Tools The LDMT14T308R-D57 WSP45G is a rectangular milling insert engineered for general milling across steel, stainless steel and heat‑resistant alloys, offering robust edge stability and dependable chip control. Tiger‑tec Gold PVD coating Versatile for P, M and S materials D57 chipbreaker for controlled chips 15° clearance angle for stable cutting High productivity through proven coating and grade The combination of the Tiger‑tec Gold coating and the WSP45G coated‑carbide grade delivers a balance of wear resistance and toughness, designed to keep machining cycles productive. In practice, this means longer tool life under mixed cutting loads and improved resistance to edge chipping when machining demanding alloys. The coated grade is particularly suited to typical milling tasks in steel, stainless steel and superalloys, supporting consistent material removal rates with fewer tool changes and reduced downtime. Reliable chip control and stronger cutting edges A defining benefit of the insert is the D57 chipbreaker, which promotes controlled chip formation across finishing and semi‑roughing passes. Controlled chips reduce the risk of surface damage and help evacuate swarf efficiently from the cut, improving process stability. Combined with the 15° clearance angle, the geometry supports a predictable cutting action that protects the cutting edge and contributes to repeatable surface quality in series production. Design details that support versatility and finish quality The insert’s rectangular format and 0.8 mm corner radius offer a compromise between strength and surface finish: the radius provides a robust cutting edge for interrupted cuts while still enabling respectable surface quality on final passes. The T3 thickness enhances rigidity in the seat, reducing vibration and aiding dimensional stability in milling operations. These mechanical attributes make the component suitable for a range of slotting, face milling and shoulder milling tasks where a reliable, versatile insert is required. For application support or to secure Walter Tools Tiger‑tec Gold inserts such as the LDMT14T308R‑D57 WSP45G, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: LDMT14T308R-D57-WSP45G-WALTER Designation: LDMT14T308R-D57 WSP45G Manufacturer: Walter Tools Series: Tiger‑tec Gold Tolerance class: M Core dimensions and values Plate size: 14 Corner radius: 0.8 mm Clearance angle: 15° Thickness: T3 Materials, geometry and features Chipbreaker: D57 Applicable materials: P / M / S Plate form: Rectangular Grade: WSP45G FAQ Which materials can this insert machine effectively? The LDMT14T308R‑D57 WSP45G insert is specified for P, M and S groups — in other words for unalloyed and alloyed steel, stainless steel and heat‑resistant superalloys or titanium‑based materials. What advantages does the Tiger‑tec Gold coating provide? The Tiger‑tec Gold coating on the WSP45G grade improves wear resistance while maintaining edge toughness, resulting in longer cutting life and stable performance in both finishing and semi‑roughing milling. How does the D57 chipbreaker influence machining? The D57 chipbreaker shapes chips to aid evacuation and reduce the likelihood of built‑up edge, which supports better surface quality and fewer interruptions during production runs. Is the geometry suitable for interrupted cuts? Yes — the rectangular format with a 0.8 mm corner radius and T3 thickness provides enhanced edge strength, making the insert suitable for interrupted and general milling tasks. What tolerance class does this insert conform to? The insert is manufactured to tolerance class M, ensuring dimensional consistency for secure seating and repeatable performance. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names mentioned are the property of their respective owners. Brand names and trademarks are used for explanatory purposes only and do not imply any affiliation between our company and the named brands. The item offered is an original, factory‑new product of the manufacturer.
LDMT14T308R-F57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the WKP25S grade for durable, economical milling of steel and cast iron; the insert’s 15° relief and 0.8 mm corner radius ensure stable cutting and improved surface quality. Order the insert directly via Metav Werkzeuge or consult the technical team for application advice. LDMT14T308R-F57 WKP25S — Indexable milling insert, Tiger·tec Silver for steel & cast iron (Walter Tools) The LDMT14T308R-F57 WKP25S is a rectangular indexable milling insert engineered for productive face and shoulder milling in steel and cast iron, combining coated carbide performance with a chipbreaker optimised for controlled chip formation. Tiger·tec Silver coated carbide for long life Optimised for steel (P) and cast iron (K) 15° relief angle for stable cutting 0.8 mm corner radius for smooth finishes Reliable performance on steel and cast iron The combination of the Tiger·tec Silver technology and the WKP25S grade delivers a wear-resistant, coated-carbide solution that is designed to cope with the thermal and abrasive demands typical when machining steel (ISO group P) and cast iron (ISO group K). The coating and substrate pairing promote stable chip formation, reduced flank wear and consistent cutting forces, which together support longer tool life and fewer insert changes. The integrated chipbreaker F57 assists in breaking and evacuating chips to maintain process stability and reduce the risk of re-cutting. Geometry tuned for accuracy and surface finish A 15° relief promotes reliable entry and exit behaviour, reducing cutting edge stresses and vibration during interrupted cuts. The 0.8 mm corner radius helps to distribute cutting loads and improve workpiece surface quality without compromising strength at the cutting edge. The rectangular format (size 14) and T3 thickness provide a robust support platform in the tool holder, while the tolerance class M ensures consistent fit and repeatable seating for accurate machining and predictable part quality. Process benefits and handling advantages As an indexable milling insert, this product supports economical machining by offering multiple cutting edges per insert and straightforward replacement, lowering cost per component in volume production. The LDMT14T308R-F57 WKP25S belongs to the Tiger·tec Silver series, known for good overall process reliability and broad material coverage, making it suitable for mixed-production environments. The insert’s design reduces downtime for tool changes and aids in achieving reproducible results across batches, supporting higher productivity and simplified tool management. Contact Metav Werkzeuge for availability and tailored application advice on the Walter Tools LDMT14T308R-F57 WKP25S insert — eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data SKU: LDMT14T308R-F57-WKP25S-WALTER Designation: LDMT14T308R-F57 WKP25S Series: Tiger-tec Silver Manufacturer: Walter Tools Core data Relief angle: 15° Corner radius: 0.8 mm Plate size: 14 Thickness: T3 Tolerance class: M Special features Chipbreaker: F57 Grade: WKP25S (coated carbide) Material suitability: Steel (P) and Cast iron (K) Plate form: Rectangular Execution: T FAQ What materials is this insert suitable for? The LDMT14T308R-F57 WKP25S is formulated for steel (ISO group P) and cast iron (ISO group K); the Tiger·tec Silver coating and WKP25S grade balance wear resistance and chip control for these groups. How does the chipbreaker F57 affect machining? The F57 chipbreaker promotes controlled chip formation and evacuation, reducing recutting and aiding stable machining when using the Walter Tools insert in interrupted or continuous cuts. Which geometry features improve surface finish? The 15° relief angle together with the 0.8 mm corner radius reduces cutting edge stress and vibration, contributing to improved surface quality and consistent part finishes. Is this insert compatible with standard toolholders? The rectangular LDMT geometry and T3 thickness are compatible with holders designed for LDMT-style inserts; proper clamping and seat cleanliness are recommended for repeatable accuracy with the Walter Tools insert. What does the grade designation WKP25S indicate? WKP25S denotes a Walter Tools coated-carbide grade within the Tiger·tec Silver range, optimised for productive machining of steel and cast iron with good wear resistance and stable cutting behaviour. The Walter AG (brand appearance: Walter Tools) is part of the Sandvik Group. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
LDMT14T308R-F57 WKP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and the WKP35G grade for extended tool life and consistent chip control when machining steel and cast iron; order directly via Metav Werkzeuge or consult our specialists for application recommendations. LDMT14T308R-F57 WKP35G — Indexable milling insert, Tiger‑tec Gold, Walter Tools The LDMT14T308R‑F57 WKP35G is an indexable milling insert engineered for general milling of steel and cast iron, offering high wear resistance and reliable chip formation in continuous production environments Tiger‑tec Gold coating for high wear resistance Optimised F57 chipformer for stable chip control Rectangular form, 15° clearance, 0.8 mm corner radius Suitable for steel (P) and cast iron (K) Longer tool life through advanced coating technology The combination of the Tiger‑tec Gold series and the WKP35G grade delivers a coated carbide substrate designed for high thermal and abrasive loads. This engineered coating reduces flank wear and helps maintain cutting-edge integrity over extended production runs. For manufacturers seeking a measurable reduction in tool changes, the hardened coating translates into lower downtime and fewer tool inventories to manage, while preserving component tolerances and repeatability. Stable chip control that improves surface quality The integrated F57 chipformer is tailored to produce consistent, controllable chips when machining both steel (P) and cast iron (K) per ISO 513 groupings. Controlled chip formation reduces recutting, improves coolant access and contributes directly to improved surface finishes and tool life. In practice this yields fewer scrap parts and a steadier cycle time, which supports predictable machining schedules and higher first-pass yields. Robust geometry for secure cutting performance A 15° clearance combined with a 0.8 mm corner radius and rectangular form gives the insert mechanical strength where it matters most: at the cutting edge and contact zones. The geometry, together with tolerance class M and a T3 thickness, balances edge stability and versatility across a range of cutters. This results in reliable performance for medium-duty milling operations where both edge life and dimensional stability are priorities. Fit-for-purpose specification and production advantages Specified as an indexable milling insert, this grade and form factor integrate seamlessly with standard toolholders and tool systems used in jobbing and production shops. The insert’s focus on process reliability and stable edge life helps reduce the need for frequent requalification of tool offsets and shortens setup times. If application-specific data or cutting parameters are required, Metav Werkzeuge can advise on optimal cutting speeds and feeds to match machine capability and workpiece material. For proven performance with Walter Tools Tiger‑tec Gold inserts consult Metav Werkzeuge for tailored recommendations and cutting data; contact info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific applications Technical Data Article number: LDMT14T308R-F57-WKP35G-WALTER Manufacturer: Walter Tools Product type: Indexable milling insert Designation: LDMT14T308R-F57 WKP35G Series: Tiger‑tec Gold Grade: WKP35G Core data Clearance angle: 15° Corner radius: 0.8 mm Chipformer: F57 Plate size: 14 mm Plate thickness: T3 Tolerance class: M Special features Coating: Tiger‑tec Gold (coated carbide) Material application: Steel (P), Cast iron (K) Plate form: Rectangular Execution: T FAQ What materials is this insert suitable for? The LDMT14T308R‑F57 WKP35G insert is designed primarily for steel (P) and cast iron (K) applications according to ISO 513 groupings. How does the Tiger‑tec Gold coating affect performance? The Tiger‑tec Gold coating on the WKP35G grade improves wear resistance and thermal stability, resulting in longer tool life and more consistent cutting performance. Which chipformer does this insert use and why does it matter? This insert features the F57 chipformer, optimised for stable chip control to reduce recutting and improve surface finish during milling of steel and cast iron. Is the geometry suitable for general-purpose milling? Yes; the combination of 15° clearance, a 0.8 mm corner radius and a rectangular form provides a balance of edge strength and versatility for medium-duty milling operations. Can this insert be used in standard toolholders? The insert follows common indexable insert formats and is compatible with corresponding holders specified for its ISO designation and form. Walter Tools (Walter AG) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and forms part of a major global group. Marked trade names and product designations are the property of their respective owners and are used here for descriptive purposes only. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany
LDMT14T308R-F57 WPP35G WPP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and the WPP35G carbide grade for consistent, high‑productivity milling of Stahl; the insert’s 15° relief angle and 0.8 mm corner radius provide secure cutting engagement and predictable tool life. Order directly via Metav Werkzeuge or consult the Metav team for cutting data and availability. LDMT14T308R-F57 WPP35G milling indexable insert for Stahl — Walter Tools The LDMT14T308R-F57 WPP35G is a rectangular milling insert engineered for productive machining of Stahl, featuring the Tiger‑tec Gold coating technology. Tiger‑tec Gold coating for high performance WPP35G coated carbide for Stahl machining 15° relief angle for secure engagement 0.8 mm corner radius for stable cutting edge Maximised productivity through premium coating and substrate The Tiger‑tec Gold series combines a wear‑resistant coating with a robust substrate to deliver consistent performance in demanding milling applications. The WPP35G grade is a coated carbide formulation optimised for machining Stahl, providing a balance between wear resistance and toughness. Thanks to this combination, the insert maintains cutting‑edge integrity under thermal and mechanical loads typical for steel machining, which translates into longer effective tool life and fewer tool changes during production. Predictable chip formation and improved surface quality The dedicated F57 chipbreaker controls chip shape and evacuation to reduce rework and downtime. Combined with the 0.8 mm corner radius, this geometry limits edge chipping and stabilises the cut, resulting in more uniform surface finishes and repeatable part quality. The insert’s tolerance class M ensures dimensional consistency between indexed corners, supporting predictable tool cycles and efficient process planning. Secure seating and geometry for demanding milling passes With a 15° relief angle, the insert provides a positive cutting geometry that reduces cutting forces during light and medium milling passes. The rectangular plate form and a plate size of 14 mm enable straightforward clamping in standard milling cutter bodies, while the plate thickness T3 contributes to mechanical stability under intermittent and continuous loads. Integration into existing tool systems is simplified by the LDMT designation and industry‑standard form factor, making the component suitable for many conventional and high‑productivity milling setups. Application focus and machining benefits Designed primarily for Stahl, the insert supports a wide range of steel types as classified by ISO, from wear‑resistant to more ductile steels. The WPP35G grade, as part of Tiger‑tec Gold, targets operators seeking a reliable compromise between tool life and surface quality. For process engineers, the combination of coating, substrate and chipbreaker minimises unexpected process variation and makes performance more reproducible across batches. For reliable, high‑productivity milling with Tiger‑tec Gold, contact Metav Werkzeuge for tailored cutting data and availability via info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number / SKU: LDMT14T308R-F57-WPP35G-WALTER Label: Fräswendeschneidplatte LDMT14T308R-F57 WPP35G Walter Tools Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WPP35G Designation: LDMT14T308R-F57 Facts Relief angle: 15° Corner radius: 0.8 mm Plate size: 14 mm Plate thickness: T3 Tolerance class: M Special features Coating: Tiger‑tec Gold technology Substrate: coated carbide (WPP35G) Chipbreaker: F57 Plate form: rectangular Application group: Stahl (P) FAQ Which materials is this insert designed to machine? The LDMT14T308R‑F57 WPP35G insert from Walter Tools is designed primarily for machining Stahl (steel), as indicated by its application grouping and WPP35G grade characteristics. What does the WPP35G designation indicate? WPP35G denotes Walter Tools’ coated carbide grade within the Tiger‑tec Gold family; it is formulated for a balanced combination of wear resistance and toughness suitable for Stahl machining. How does the F57 chipbreaker affect machining? The F57 chipbreaker shapes and breaks chips to improve evacuation, reduce heat concentration, and promote consistent surface finish when using the LDMT14T308R‑F57 WPP35G insert. Why is the 15° relief angle important? A 15° relief angle gives a positive cutting geometry that reduces cutting forces and supports secure engagement during milling, which helps preserve the cutting edge and improve process stability. What are the key dimensional specifications to check for tool compatibility? Key dimensions for compatibility are the 14 mm plate size, T3 thickness and the rectangular plate form; these determine seat fit and clamping in standard milling cutter bodies. Manufacturer: Walter Tools / Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand presence: Walter Tools) with headquarters in Tübingen is among the world's leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered item is original, factory‑new goods from the manufacturer.
LDMT14T308R-F57 WSM35G WSM35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the WSM35G grade for reliable machining of stainless steel and superalloys; benefit from stable chip control and extended tool life. Order directly via Metav Werkzeuge or consult our technical advisors for application-specific recommendations. LDMT14T308R-F57 WSM35G milling insert – Tiger·tec Gold grade for stainless steel and Superalloys (Walter Tools) The LDMT14T308R-F57 WSM35G is a rectangular milling insert designed for demanding milling tasks on stainless steel and heat‑resistant superalloys and titanium, offering a balance of edge stability and thermal resistance. Tiger·tec Gold coating technology WSM35G grade for tough alloys 15° clearance angle for stable cutting 0.8 mm corner radius, rectangular insert High performance on difficult-to-machine alloys The coated carbide formulation of the WSM35G grade, produced within the Tiger·tec Gold series, is engineered for elevated thermal and mechanical loads. As a coated carbide insert, it supports secure chip formation and a stable cutting edge, which reduces the risk of built‑up edge when machining stainless steel and Superalloys. The result is fewer interruptions in production and more predictable tool life, which directly benefits throughput and process planning. Geometry engineered for edge security and surface quality A 15° clearance angle combined with a 0.8 mm corner radius increases the insert's resistance to chipping while maintaining a reliable contact geometry for interrupted cuts. The chipbreaker F57 promotes controlled evacuation of swarf, reducing heat concentration at the cutting zone and improving surface finish. The rectangular insert format and T3 thickness provide a robust support area in the tool holder, improving rigidity in heavy milling operations and supporting consistent machining results. Productivity gains and process reliability in series production Using this insert supports productivity improvements through longer service intervals and consistent performance across batches. The combination of the grade and coating minimises wear mechanisms typical of high‑temperature cutting, helping to reduce tool change frequency and increase machine uptime. For manufacturers targeting repeatable tolerances on resistant materials, this solution helps maintain process stability and lowers the total cost of machining per part. Typical applications and selection guidance This insert is suited to roughing and semi‑finishing passes in industries such as aerospace, energy and specialised engineering where stainless steel and nickel‑based alloys are common. Selection of tool holder, take‑off depth and cutting data should align with machine rigidity and component geometry; the geometry and chipbreaker are optimised to support moderate depths of cut at elevated temperatures. For specific cutting‑data recommendations and holder compatibility, technical advisors can assist with tailored settings. For tailored application advice and fast availability of Walter Tools inserts like the WSM35G Tiger·tec Gold grade, contact Metav Werkzeuge for expert recommendations and immediate support via info@metav-werkzeuge.com or +49 2822 7131930. Technical data SKU: LDMT14T308R-F57-WSM35G-WALTER Designation: LDMT14T308R-F57 ISO designation: LDMT14T308R-F57 WSM35G Grade: WSM35G Series: Tiger·tec Gold Manufacturer: Walter Tools Numbers / Core technical data Clearance angle: 15° Corner radius: 0.8 mm Insert size: 14 Thickness: T3 Tolerance class: M Geometry: T Chipbreaker: F57 Designs / Special features Coating technology: Tiger·tec Gold Coated carbide grade: WSM35G Insert shape: rectangular Suitable material groups: S / M (Superalloys/Titanium; stainless steel) Application focus: heavy‑duty milling, secure chip formation FAQ Is this insert suitable for machining stainless steel? Yes. The LDMT14T308R-F57 WSM35G insert is specifically formulated for stainless steel, offering thermal resistance and chip control for these challenging materials. Can this grade be used on titanium and nickel‑based alloys? Yes. The WSM35G grade within the Tiger·tec Gold series is intended for material group S, making it suitable for heat‑resistant superalloys and titanium under appropriate cutting conditions. What does the chipbreaker F57 do? The F57 chipbreaker promotes controlled chip formation and evacuation, reducing heat concentration at the cutting edge and improving surface finish during milling with this rectangular insert. Which toolholders are compatible with the rectangular LDMT insert? Compatibility depends on the holder pocket and clamping system; the insert’s rectangular form and T3 thickness require a holder designed for LDMT‑style plates. Check the holder specifications against the ISO designation. How does the 0.8 mm corner radius affect performance? A 0.8 mm corner radius increases edge strength and improves resistance to chipping in interrupted or heavy cuts, balancing surface quality and robustness for demanding milling tasks. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only and do not indicate any affiliation with our company. The offered item is original, factory‑new goods of the manufacturer.
LDMT14T308R-F57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, versatile P/M/S material capability and a precise corner radius of 0.8 mm for consistent milling performance; order the insert directly via Metav Werkzeuge or request tailored advice from our consultants. LDMT14T308R-F57 WSP45G – milling indexable insert by Walter Tools (Tiger·tec Gold, PVD-coated) LDMT14T308R-F57 WSP45G is a rectangular milling insert designed for general milling applications where a balance of edge stability and chip control is required Tiger·tec Gold PVD-coated grade WSP45G Suitable for Stahl and rostfreier Stahl machining Rectangular insert with corner radius 0.8 mm Optimised chipformer F57 for stable chip control High efficiency and broad material range for milling operations The Tiger·tec Gold technology used in this grade provides a PVD-coated carbide surface that promotes stable chip formation and extended edge life under typical milling loads. The insert is formulated for machining across the P/M/S groups, meaning suitability for Stahl, rostfreier Stahl and high-temperature superalloys or titanium, with the substrate and coating balancing toughness and wear resistance. As a result, the insert reduces unplanned stoppages through predictable wear behaviour and consistent cutting forces, which supports steady productivity on components that demand repeatable results. Geometry engineered for reliable surface quality and repeatability The rectangular shape combined with a corner radius of 0.8 mm and a relief of 15° yields a geometry that supports stable cutting edges and good surface finishes in a range of feeds and depths. The tolerance class M ensures dimensional consistency between inserts, which is important for serial production and repeat setup routines. The thickness designation T3 and size 14 contribute to the mechanical stiffness of the pack, reducing vibration during interrupted cuts; the outcome is improved dimensional control and fewer rework cycles on parts requiring close tolerances. Practical benefits on the shop floor: chip control and cost-efficiency The integrated F57 chipformer is optimised to break and evacuate chips reliably during milling, lowering the risk of built-up edge and thermal concentration at the cutting edge. This leads to longer effective tool life and fewer insert changes per shift, supporting a lower total cost of ownership for milling operations. The grade’s balance of toughness and wear resistance facilitates a wide processing window, making the insert a practical choice for mixed production runs. For application-specific cutting data or optimisation across machining centres, Metav Werkzeuge’s technical advisers are available to assist with recommended feeds, speeds and fixture considerations. For application-specific recommendations on the Walter Tools LDMT14T308R-F57 WSP45G, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for tailored cutting data and procurement support Technical Data Article number: LDMT14T308R-F57-WSP45G-WALTER Type: Milling indexable insert Designation: LDMT14T308R-F57 WSP45G Manufacturer: Walter Tools Numbers Corner radius: 0.8 mm Relief angle: 15° Size: 14 Thickness: T3 Tolerance class: M Special features Series: Tiger·tec Gold Grade: WSP45G (PVD-coated carbide) Applicable materials: Stahl; rostfreier Stahl; high-temp superalloys and titanium Form: Rectangular Chipformer: F57 FAQ Is this insert suitable for machining stainless steels? Yes. The LDMT14T308R-F57 WSP45G grade is formulated for rostfreier Stahl and provides stable chip formation and edge resistance under the higher temperatures typical of these alloys. Which chip control does this insert offer? The insert uses an F57 chipformer, designed to produce short, controllable chips during milling, reducing the likelihood of re-cutting and built-up edge. What are the key geometry values for this insert? The insert features a corner radius of 0.8 mm and a relief angle of 15°, with a tolerance class of M for consistent interchangeability. Can this grade handle titanium and superalloys? Yes. WSP45G is specified for the S material group, enabling milling of high-temperature superalloys and titanium where heat resistance and edge strength are required. How does the Tiger·tec Gold technology help in production? The Tiger·tec Gold coating improves wear resistance and thermal stability of the cutting edge, extending the insert’s effective life and supporting predictable performance over longer cycles. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is original, brand-new goods from the manufacturer Walter Tools.
LDMT170408R-D51 WKP35G Wendeplatten - Walter Tools
Take advantage of the proven combination of Tiger‑tec Gold wear resistance and the WKP35G grade for dependable machining of steel and cast iron; the insert’s D51 chipbreaker and 15° relief together deliver stable chip control and consistent surface quality—order the insert via Metav Werkzeuge or request technical advice from our specialists. LDMT170408R-D51 WKP35G – Indexable milling insert, Tiger‑tec Gold (D51 chipbreaker, 15° relief) by Walter Tools The LDMT170408R-D51 WKP35G is a rectangular indexable milling insert engineered for robust performance in milling operations on steel and cast iron, offering a combination of a coated carbide grade and an optimised chipbreaker to support productive machining. Tiger‑tec Gold coating for long tool life Optimised for steel and cast iron machining D51 chipbreaker for reliable chip control 15° relief angle, 0.8 mm corner radius Greater process reliability through optimised grade and coating The combination of the WKP35G coated carbide grade and the Tiger‑tec Gold technology provides enhanced wear resistance and predictable flank behaviour during milling. Designed for the ISO P and K material groups, this grade addresses the heat and deformation patterns typical of steel and the abrasive, short‑breaking chips of cast iron. The result is fewer unscheduled tool changes and a more stable cutting edge, which supports consistent component tolerances and reduces overall machining variability. Technical explanations are kept concise to aid specification processes and tool selection for production planning. Geometry that stabilises cutting and improves surface finish A rectangular insert form with a 0.8 mm corner radius and a 15° relief angle contributes to a balanced cutting edge that resists chipping under interrupted cuts and delivers a reliable surface finish. The D51 chipbreaker is profiled to control chip formation in medium to heavy machining of steels and cast irons, reducing the risk of stringing and tool overload. These geometric features make the insert suitable for operations where edge stability and predictable cutting forces are priorities, for instance pocketing or face milling where consistent tool life and repeatable results are required. Productivity advantages and economical tool use Using an insert with Tiger‑tec Gold characteristics and the WKP35G grade supports longer edge life and stable wear patterns, lowering the frequency of indexing and replacement. This translates into improved uptime and a better cost per component metric in series production. The insert’s construction and chip control reduce the incidence of rework due to poor surface quality, while the tolerance class M helps ensure interchangeability and straightforward toolholder setup. These factors combine to make the insert a pragmatic choice for workshops aiming for steady throughput and controlled operating costs. Compatibility and application overview for process planning The insert is designated for machining within the P / K material classes, explicitly covering unalloyed and alloyed steels as well as a broad range of cast iron types. The coated carbide composition and the engineered chipbreaker make it suitable where moderate to high material removal rates are required while maintaining a focus on process security. For mixed workpiece fleets that include both steel and cast iron, the insert offers a versatile option that reduces the need for frequent tool changeovers and simplifies inventory management. For reliable high‑performance milling with Tiger‑tec Gold, contact Metav Werkzeuge for tailored advice and fast availability: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: LDMT170408R-D51-WKP35G-WALTER Designation: LDMT170408R-D51 WKP35G Label: Fräswendeschneidplatte LDMT170408R-D51 WKP35G Walter Tools Series: Tiger‑tec Gold Grade: WKP35G Manufacturer: Walter Tools Facts Size: 17 Thickness: 04 Corner radius: 0.8 mm Relief angle: 15° Chipbreaker: D51 Tolerance class: M Special features Material groups: P / K (steel and cast iron) Coating / grade: WKP35G (coated carbide) Plate form: Rectangular Execution: T ISO designation: LDMT170408R-D51 WKP35G FAQ What materials is this insert suitable for? The LDMT170408R-D51 WKP35G insert is suitable for steel and cast iron applications and is specified for use in ISO material groups P and K. How does the D51 chipbreaker affect machining? The D51 chipbreaker on this insert controls chip formation to promote short, manageable chips and improved heat distribution, which supports stable cutting in mixed steel and cast iron operations. What does the WKP35G grade imply for tool life? WKP35G is a coated carbide grade within the Tiger‑tec Gold family that emphasises wear resistance and consistent edge performance, contributing to extended tool life under normal milling conditions. Is this insert suitable for interrupted cuts? The rectangular geometry with a 0.8 mm corner radius and a 15° relief angle provides enhanced edge strength, making the insert resilient in interrupted cutting scenarios commonly encountered in milling. Which series and manufacturer are responsible for this product? The insert belongs to the Tiger‑tec Gold series and is supplied under the Walter Tools brand as an original factory‑new part. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only and do not imply any affiliation between Metav Werkzeuge and the named brands. The offered item is an original, factory‑new product of the manufacturer.
LDMT170408R-D51 WPP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold wear resistance, a precise D51 chipbreaker geometry and a moderate 0.8 mm corner radius for steady tool life and reproducible results; order supply or discuss application options via Metav Werkzeuge. LDMT170408R-D51 WPP35G indexable milling insert – rectangle form, for steel, Walter Tools LDMT170408R-D51 WPP35G is a rectangle indexable insert designed for efficient steel machining with a Tiger·tec Gold coated grade Tiger·tec Gold coating for extended life Grade WPP35G optimised for steel applications D51 chipbreaker for stable chip control 15° relief angle for secure cutting geometry Consistent productivity through advanced coating and grade selection The Tiger·tec Gold technology and the WPP35G grade combine to deliver improved wear resistance and predictable flank-life when machining steel. The coated carbide substrate reduces flank wear and thermal degradation during common steel cutting operations, which translates directly into extended tool life and fewer insert changes. This reduces unplanned stoppages and supports a stable production rhythm in both single- and multi-shift environments. The choice of a coated grade tuned to the P material class helps maintain cutting-edge integrity under typical heat and chip-formation conditions. Reliable chip control and geometry that protect surface finish The D51 chipbreaker and the rectangular plate geometry provide controlled chip formation and evacuation, lowering the risk of built-up edge and surface damage. The 0.8 mm corner radius supports a balance between edge strength and acceptable surface finish in semi-finish and finish passes. With a 15° relief angle the insert maintains a consistent cutting engagement and reduces the tendency to rub, improving surface integrity and dimensional consistency. These geometric decisions lead to fewer reworks and a predictable workflow for part finishing. Production-focused specifications for straightforward integration Manufactured to tolerance class M, the insert offers repeatable seating and clamping accuracy in standard cutter bodies, simplifying tool management. The plate size and thickness suit common indexable milling holders, enabling easy stocking and interchange. Because the grade is explicitly intended for steel, process planning benefits from established cutting data and reliable tool-life expectations, so feed and speed optimisation can focus on productivity gains rather than accommodating unpredictable wear behaviour. The overall package is aimed at providing measurable efficiency improvements for everyday milling tasks. Contact Metav Werkzeuge for tailored application advice, availability and to arrange a supply matching specific cutter systems and production requirements; eMail: info@metav-werkzeuge.com – Tel: +49 2822 7131930 Technical Data Article number: LDMT170408R-D51-WPP35G-WALTER SKU: LDMT170408R-D51-WPP35G-WALTER Label: Fräswendeschneidplatte LDMT170408R-D51 WPP35G Walter Tools Dimensions / Core data Clearance angle: 15° Corner radius: 0.8 mm Plate length/size: 17 mm Plate thickness: 4 mm Tolerance class: M Special features / Versions Coating/grade: Tiger·tec Gold (WPP35G) Chipbreaker: D51 Shape: Rectangle Material application: Steel (P) Series: Tiger·tec Gold Execution: T Manufacturer: Walter Tools FAQ Which materials is this insert suitable for? The insert is intended for steel applications; the Tiger·tec Gold WPP35G grade is optimised for typical steel cutting conditions and chip formation. What advantages does the Tiger·tec Gold coating provide? Tiger·tec Gold increases wear resistance and thermal stability, so the insert sustains cutting performance longer and delivers more consistent part quality over its life. What does the D51 chipbreaker achieve in practice? The D51 chipbreaker is shaped for controlled chip formation and evacuation, reducing the risk of entanglement and improving surface finish during milling. Is this insert suitable for stainless or hardened steels? The available data indicates designation for the P material class (steel); no specific data for stainless or hardened steels is provided for this grade. What does tolerance class M mean for tool setup? Tolerance class M indicates standard machining tolerances for accurate seating and repeatable clamping in compatible cutter bodies. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are used for explanation only and do not imply any affiliation with our company. The offered item is an original, factory-new product of the manufacturer.
LDMT170408R-D51 WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold PVD-coated carbide, a stabilised cutting edge and precise geometry for dependable milling performance; secure the LDMT170408R-D51 WSP45G via Metav Werkzeuge or contact the team for tailored application advice. LDMT170408R-D51 WSP45G — Milling Insert, 15° Clearance, Walter Tools The LDMT170408R-D51 WSP45G is a rectangular milling indexable insert engineered for versatile machining across steel, stainless steel and heat-resistant alloys. Tiger·tec Gold PVD coating For steel, stainless and superalloys 15° clearance angle Rectangular form, 0.8 mm corner radius Longer tool life through advanced coating technology The insert is part of the Tiger·tec Gold series and uses a PVD-coated carbide grade designed to extend cutting life under typical milling stresses. The layered coating reduces wear and supports a stable cutting edge, which means fewer interruptions for tool changes and more consistent component quality. For production environments this translates into measurable improvements in uptime and a lower cost per part when compared with uncoated grades. Reliable chip control for challenging materials Equipped with a D51 chipbreaker, this insert promotes controlled chip formation during milling of P-, M- and S-group materials. That is, the grade is suited to steel, stainless steel and heat-resistant superalloys and titanium where chip evacuation and thermal loads can be problematic. Improved chip control reduces built-up edge and helps maintain surface finish, so process stability and repeatability increase even in tougher applications. Geometry that supports precision and repeatability The rectangular plate form combined with a 15° clearance angle and a 0.8 mm corner radius delivers predictable engagement and consistent cutting forces in interrupted and continuous cuts. The size and thickness codes ensure compatibility with common toolholders while the tolerance class M indicates a standardised fit for repeatable seating. Together, these geometric features reduce vibration and contribute to stable dimensional results part after part. Designed to boost productivity and process security As a member of a well-established tool series, this insert emphasises productivity and process security through balanced toughness and wear resistance. The grade’s versatility across a wide range of materials reduces the need for multiple specialised inserts, streamlining tooling inventories. For operations seeking dependable performance under mixed workloads, the combination of coating, chip control and geometry supports higher throughput with consistent quality. Contact Metav Werkzeuge for application-specific recommendations on Tiger·tec Gold inserts and to arrange supply of the LDMT170408R-D51 WSP45G to optimise milling productivity Technical data SKU: LDMT170408R-D51-WSP45G-WALTER Article designation: LDMT170408R-D51 WSP45G Label: Fräswendeschneidplatte LDMT170408R-D51 WSP45G Walter Tools UID: LDMT170408R-D51-WSP45G-WALTER Manufacturer: Walter Tools Numbers Clearance angle: 15° Corner radius: 0.8 mm Size code: 17 Thickness code: 04 Tolerance class: M Design & features Series: Tiger·tec Gold Grade: WSP45G (PVD-coated carbide) Applicable materials: P / M / S (steel, stainless steel, superalloys/titanium) Chipbreaker: D51 Form: Rectangular Execution: T FAQ What materials is this insert suitable for? The LDMT170408R-D51 WSP45G milling insert from Walter Tools is specified for P, M and S material groups — effectively covering steel, stainless steel and heat-resistant superalloys (including titanium). What benefits does the Tiger·tec Gold coating provide? Tiger·tec Gold is a PVD coating that increases wear resistance and supports a stable cutting edge; the result with the LDMT170408R-D51 WSP45G is extended tool life and improved process stability in milling operations. How does the D51 chipbreaker influence machining? The D51 chipbreaker on this insert promotes controlled chip formation and reliable evacuation, reducing the risk of built-up edge and helping to maintain consistent surface quality during milling. Which geometries should be noted for setup and performance? Key geometry values are the 15° clearance angle and 0.8 mm corner radius; these features help to manage cutting forces and support repeatable seating and run-out compensation in compatible toolholders. Can this insert replace multiple grades in a mixed production environment? Yes — the grade’s balanced toughness and wear resistance make the LDMT170408R-D51 WSP45G a versatile option for varied milling tasks, helping to simplify tooling inventories and improve throughput. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes and do not indicate any affiliation with our company. The offered item is an original, factory-new product from the manufacturer.
LDMT170408R-D57 WKK25G WKK25G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, a WKK25G grade tuned for abrasive cast iron, and a compact 15° clearance geometry to ensure predictable tool life and consistent metal removal in series production. Order the LDMT170408R-D57 WKK25G milling insert directly via Metav Werkzeuge or ask the Metav consultants for application support. LDMT170408R-D57 WKK25G milling indexable insert for cast iron – 15° clearance by Walter Tools LDMT170408R-D57 WKK25G is a rectangular indexable milling insert engineered for productive machining of cast iron components in industrial production and job-shop environments. Tiger·tec Gold coating for wear resistance Optimised for cast iron machining 15° clearance angle for stable engagement Rectangular shape, 0.8 mm nose radius Deliverable productivity for abrasive cast iron workpieces The combination of the Tiger·tec Gold coating and the WKK25G cutting grade is designed specifically for the demands of cast iron machining. The coated cemented carbide substrate resists the abrasive wear typical of grey and nodular cast iron, which reduces flank wear and extends usable edge life. As a result, cycle times remain stable across longer production runs and process windows widen, supporting higher throughput with fewer tool changes. Predictable chip control and edge security for roughing operations The D57 chipbreaker geometry and the 15° clearance deliver controlled chip formation and secure edge support during interrupted cuts typical of milling cast components. A 0.8 mm corner radius balances strength and form — it absorbs peak loads while allowing effective metal removal without excessive cutting forces. These geometry choices translate into fewer edge failures and consistent surface quality when roughing and semi-finishing cast iron parts. Compact geometry for flexible integration and repeatable set-ups The insert’s rectangular form and compact dimensions (approx. 17 mm nominal size with 4 mm thickness and tolerance class M) allow straightforward integration into standard face and shoulder milling cutters. The indexable design simplifies tool management: worn edges are rotated to a fresh corner, keeping machine downtime to a minimum and supporting predictable production planning. The insert’s T designation and robust grade make it suitable for medium- to heavy-duty roughing where cost-effective performance and process reliability are priorities. For availability, application recommendations and quick supply of Walter Tools Tiger·tec Gold inserts such as the LDMT170408R-D57 WKK25G, contact Metav Werkzeuge for expert advice via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number / SKU: LDMT170408R-D57-WKK25G-WALTER Product name: LDMT170408R-D57 WKK25G Manufacturer brand: Walter Tools Product type: Milling indexable insert Grade / sort: WKK25G Coating series: Tiger·tec Gold Form: Rectangular Chipbreaker: D57 Clearance angle: 15° Corner radius: 0.8 mm Plate size: 17 mm Plate thickness: 4 mm Tolerance class: M Execution: T Material code: K (suitable for cast iron) Cast iron application: Yes Facts Clearance angle: 15° Corner radius: 0.8 mm Size (nominal): 17 mm Thickness: 4 mm Tolerance class: M Special features Tiger·tec Gold coating technology WKK25G coated cemented carbide grade Rectangular insert shape D57 chipbreaker for chip control Optimised for cast iron machining Indexable insert — multiple cutting edges Series: Tiger-tec Gold FAQ What materials is this insert designed for? The LDMT170408R-D57 WKK25G from Walter Tools is optimised for cast iron applications; the WKK25G grade and Tiger·tec Gold coating address the abrasive nature and short, brittle chips typical of these materials. How does the D57 chipbreaker affect cutting performance? The D57 chipbreaker promotes consistent chip formation and evacuation during milling, reducing the risk of chip-related interruptions when using the LDMT170408R-D57 WKK25G insert in interrupted or continuous cuts. Which geometry features increase edge life in this insert? A 15° clearance angle combined with a 0.8 mm corner radius provides stable edge support and lowers peak loads on the cutting edge, helping to extend tool life under roughing conditions. Can the insert be used for finishing operations? The LDMT170408R-D57 WKK25G is primarily tuned for productive roughing and semi-finishing of cast iron; for high-quality finishing, a dedicated finishing grade and smaller nose radius are typically recommended. What is the tolerance class and why does it matter? Tolerance class M indicates the manufacturing precision of the insert and its fit in the pocket; consistent tolerances support repeatable set-ups and accurate cutter geometry across indexable insert changes. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Protected trademarks and trade names are the property of their respective owners. The brand name Walter Tools is mentioned for identification purposes only and does not imply any affiliation with Metav Werkzeuge. The offered item is an original, factory-new product of the manufacturer.
LDMT170408R-D57 WKP25S Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Silver coating and the WKP25S grade for improved wear resistance and reliable chip control; the insert's 15° clearance and 0.8 mm nose radius support consistent surface quality in milling. Order the insert directly via Metav Werkzeuge or consult our specialists for application advice. LDMT170408R-D57 WKP25S indexable milling insert — Tiger‑tec Silver, for Stahl & Gusseisen | Walter Tools A LDMT170408R-D57 WKP25S indexable milling insert engineered for robust medium to heavy milling of Stahl and Gusseisen, offering enhanced tool life and stable chip formation. Tiger‑tec Silver coating for high wear resistance WKP25S grade optimised for Stahl and Gusseisen 15° clearance angle for stable cutting geometry Rectangular insert with 0.8 mm nose radius Longer service life through advanced coating technology The combination of the Tiger‑tec Silver coating and the WKP25S carbide grade delivers measurable improvements in abrasion resistance and edge stability. Coating technology reduces flank wear under elevated temperatures common when machining Stahl, which translates into longer intervals between index changes and lower tooling costs per component. For operations that require sustained productivity, the coated insert supports consistent performance across batch runs and helps maintain machining parameters without frequent adjustment. Consistent chip control and improved surface finish Equipped with the D57 chipbreaker and a rectangular form, the insert promotes repeatable chip formation, which reduces the risk of built-up edge and interruptions. The 0.8 mm nose radius contributes to a balance between edge strength and surface integrity, enabling good component finish while resisting chipping in interrupted cuts. Stable chip evacuation reduces tool wear and the potential for rework, supporting higher first-pass yields on cast and steel components. Precision geometry for process security and productivity The insert's 15° clearance angle and robust edge geometry ensure a defined cutting relationship that is less sensitive to machine vibrations and fixture variations. This geometry supports reliable indexability and repeatability in multi‑tool setups, shortening changeover time compared with re‑grindable tools. As a result, the insert offers a pragmatic route to increased spindle utilisation and consistent cycle times in series production. Practical integration into production workflows As a standard rectangular indexable insert, the component is compatible with common cutter bodies that accept the LDMT footprint, enabling fast replacement and simplified inventory management. The combination of coated carbide material and optimised chip control reduces the need for excessive cutting parameter adjustments, freeing up engineering time for other process improvements. For specific machine or application questions, technical advice is available to ensure optimal tool selection and parameter settings. Contact Metav Werkzeuge for tailored application support and stock information for Walter Tools inserts; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: LDMT170408R-D57-WKP25S-WALTER Designation: LDMT170408R-D57 WKP25S Series: Tiger‑tec Silver Manufacturer: Walter Tools Type: Fräswendeschneidplatte (indexable milling insert) Grade: WKP25S Form: Rectangular Core specifications Clearance angle: 15° Corner radius: 0.8 mm Size: 17 mm Thickness code: 04 Chipbreaker: D57 Tolerance class: M Features & applications Coating: Tiger‑tec Silver Material basis: Coated carbide Suitable for: Stahl (ISO P), Gusseisen (ISO K) Main application: Milling Design: Rectangular insert, indexable FAQ Is this insert suitable for machining steel? The LDMT170408R-D57 WKP25S from Walter Tools is designed for machining Stahl (ISO group P) and is optimised to handle the heat and chip behaviour typical of steel cutting. Can this insert be used for cast iron workpieces? Yes. The WKP25S grade and the D57 chipbreaker are configured for effective chip control when machining Gusseisen, providing stable cutting and good wear resistance. What advantages does Tiger‑tec Silver provide? The Tiger‑tec Silver coating improves abrasion resistance and edge life, which enhances process security and reduces the frequency of index changes in serial milling applications. What do the 0.8 mm radius and 15° clearance deliver in practice? A 0.8 mm corner radius gives improved edge robustness for interrupted cuts, while the 15° clearance angle establishes a stable cutting geometry that supports repeatable machining results. Is the insert recommended for rostfreier Stahl (stainless steel)? No specification for rostfreier Stahl is provided for this grade; the LDMT170408R-D57 WKP25S is specified for Stahl and Gusseisen only. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Walter AG (brand appearance: Walter Tools) is a leading manufacturer of precision tools for metalworking and forms part of the Sandvik Group. Protected trademarks and product names remain the property of their respective owners. The mentioned brand is cited solely for explanatory purposes and does not imply any affiliation.
LDMT170408R-D57 WKP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold wear resistance, a WKP35G grade optimised for steel and cast iron, and precise D57 chip control for consistent, productive milling — order directly via Metav Werkzeuge or consult our specialists for application advice. LDMT170408R-D57 WKP35G rectangular milling insert by Walter Tools — 15° clearance, 0.8 mm nose radius LDMT170408R-D57 WKP35G is a rectangular milling insert designed for high-productivity finishing and roughing in steel and cast iron applications, featuring Tiger·tec Gold coating and a D57 chipbreaker geometry Tiger·tec Gold coating for high wear resistance WKP35G grade for steel and cast iron machining Rectangular insert 17 mm with 0.8 mm nose radius 15° clearance angle with D57 chipbreaker geometry Improved productivity through advanced coating and grade The combination of the Tiger·tec Gold coating with the WKP35G carbide grade delivers a measurable improvement in wear resistance and edge stability. This insert is engineered to withstand the thermal and abrasive loads typical for ISO P (steel) and ISO K (cast iron) machining, which means longer tool life and fewer interruptions for tool changes. The coated carbide substrate reduces flank wear and maintains cutting-edge integrity under cyclic loads, supporting steadier production rates and consistent part quality. For users transitioning from general-purpose inserts, this specification reduces the need for frequent regrinding or replacement, resulting in lower total operating costs and reduced setup time. Precise geometry for controlled chips and surface quality A well-defined chipbreaker and a 0.8 mm nose radius ensure effective chip formation and reliable surface finish in both finishing and semi-finishing passes. The D57 chipbreaker is tuned to produce short, predictable chips when machining steels and cast irons, minimising the risk of chip entanglement and secondary machining. The 15° clearance angle reduces rubbing and temperature build-up at the flank, helping to maintain dimensional accuracy over longer runs. These geometric details translate into fewer rejects and reduced manual rework, particularly on components where surface integrity and tolerances are critical. Practical benefits: handling, compatibility and process security With a compact 17 mm rectangular format and a plate thickness of 04, the insert fits a wide range of tooling systems that accept the LDMT geometry and promotes simple, repeatable clamping. The product tolerance class M supports consistent seat fit and repeatability across multiple inserts, which simplifies tool change procedures and reduces downtime. As this is a coated carbide insert, users benefit from a balance of toughness and hardness: the substrate provides fracture resistance, while the multi-layer coating improves resistance to abrasive wear. In process terms, this means reliable performance across variable batch sizes and material batches without extensive parameter tuning. Efficient material coverage and application notes The insert is specified for machining both steels (ISO P) and cast irons (ISO K), reflecting the WKP35G sort’s design focus on handling typical heat development and chip forms for these materials. In practice, that means good performance in through-feed milling, face milling and shoulder operations where mixed batches of steel and cast iron parts are common. For machinists less familiar with ISO group designations: P indicates steels, including unalloyed and alloyed grades; K denotes cast irons, which typically generate more abrasive, brittle chips. Selecting cutting parameters in line with the workpiece material and the machine’s rigidity will deliver the best balance between tool life and productivity. Contact Metav Werkzeuge for tailored recommendations on using the Walter Tools LDMT170408R-D57 WKP35G in specific machines or components — Metav Werkzeuge can advise on cutting data and holder compatibility; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: LDMT170408R-D57-WKP35G-WALTER Manufacturer: Walter Tools Product type: Milling insert Grade: WKP35G Series: Tiger·tec Gold Geometry: LDMT170408R-D57 Facts Nose radius: 0.8 mm Clearance (free) angle: 15° Insert size: 17 mm Plate thickness: 04 Tolerance class: M Special features Coating: Tiger·tec Gold (coated carbide) Applicable material groups: P (steel), K (cast iron) Chipbreaker: D57 Plate form: Rectangular Execution: T FAQ What materials is this insert designed to machine? The LDMT170408R-D57 WKP35G milling insert by Walter Tools is designed primarily for ISO P (steel) and ISO K (cast iron) applications, with the WKP35G grade optimised for those material groups. How does the Tiger·tec Gold coating benefit production? The Tiger·tec Gold coating on this Walter Tools insert improves wear resistance and edge stability, extending tool life and supporting consistent part quality over longer production runs. Which chip type can be expected with the D57 chipbreaker? The D57 chipbreaker promotes short, controlled chips in both steels and cast irons, reducing the chance of chip tangling and simplifying chip evacuation. Is the insert compatible with standard LDMT toolholders? The LDMT170408R-D57 geometry follows common LDMT dimensions; compatibility depends on the specific toolholder model, but the rectangular 17 mm format is widely supported across standard holders. What practical advantage does the 0.8 mm nose radius provide? A 0.8 mm nose radius gives a balance between surface finish and strength at the cutting edge, improving surface integrity while maintaining sufficient edge robustness for semi-finishing operations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
LDMT170408R-D57 WPP35G WPP35G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating and a dedicated D57 chipbreaker for reliable chip control and extended tool life; the rectangular geometry with a 0.8 mm corner radius ensures stable cutting in steel and consistent insertion fit — order via Metav Werkzeuge or consult the team for tailored advice. LDMT170408R-D57 WPP35G indexable milling insert — steel application, rectangular form | Walter Tools LDMT170408R-D57 WPP35G is an indexable milling insert designed for efficient steel machining with a Tiger·tec Gold coating and a dedicated chipbreaker Tiger·tec Gold coating for extended tool life Rectangular form with 0.8 mm corner radius Dedicated D57 chipbreaker for stable chip control Tolerance class M for consistent seating Longer tool life and predictable performance through Tiger·tec Gold The Tiger·tec Gold coating combined with a coated carbide substrate provides a balance of wear resistance and toughness that reduces flank wear under the typical temperatures encountered when machining steel. This cutting grade, WPP35G, is optimised for productive roughing and versatile finishing operations, lowering tool-change frequency and improving uptime. The coated surface reduces adhesion and edge degradation, which leads to longer tool life and fewer interruptions on the production floor. Geometry that improves chip control and surface consistency The rectangular design with a 0.8 mm corner radius and the integrated D57 chipbreaker direct chip flow away from the cutting zone, reducing re-cutting and thermal load on the cutting edge. A 15° clearance angle reduces rubbing while maintaining a stable engagement geometry, and the tolerance class M helps ensure repeatable seating in standard toolholders. These features together deliver consistent results across batches and support predictable process parameters for high-volume milling of unalloyed and alloyed steels. Practical benefits for process efficiency and tool selection Designed for general steel applications (ISO group P), the insert supports a broad range of feeds and cutting speeds, enabling a simple standardisation of tooling across similar jobs. Improved chip control and a robust edge increase material removal rates without sacrificing surface quality, which can translate into higher throughput and lower unit costs. For assistance in matching cutting data and holder selection, Metav Werkzeuge provides technical consultation by email or phone: info@metav-werkzeuge.com | +49 2822 7131930 Contact Metav Werkzeuge for expert support on Walter Tools Tiger·tec Gold inserts and to arrange supply, specification matching or batch orders through Metav Werkzeuge GmbH Technical data Article number: LDMT170408R-D57-WPP35G-WALTER Designation: LDMT170408R-D57 WPP35G Manufacturer: Walter Tools Product type: Indexable milling insert Series: Tiger-tec Gold Core dimensions Size: 17 mm Thickness: 4 mm Corner radius: 0.8 mm Clearance angle: 15° Materials & special features Grade: WPP35G Chipbreaker: D57 Form: Rectangular Substrate/coating: coated carbide (Tiger·tec Gold) Tolerance class: M Execution: T Suitable for: Steel (ISO P) FAQ What materials is this insert designed for? The LDMT170408R-D57 WPP35G insert is specified for machining steel (ISO P); the WPP35G grade and Tiger·tec Gold coating are optimised for typical steel cutting temperatures and chip formation. How does the D57 chipbreaker affect machining? The D57 chipbreaker on this Walter Tools insert promotes controlled chip formation and evacuation, reducing re-cutting and heat concentration for more stable cutting conditions and improved tool life. What does the 0.8 mm corner radius mean for surface finish? A 0.8 mm corner radius balances edge strength and surface integrity, providing a good compromise between robustness in roughing and the potential for acceptable surface finish in semi-finish operations. Which toolholders are compatible with this insert designation? The LDMT170408R-D57 form and tolerance class M correspond to standard rectangular indexable insert holders for milling; confirm holder model and clamp style to ensure correct seating and orientation. Is this insert suitable for finishing operations? The coated WPP35G grade is versatile and can be used in finishing with appropriate feeds and speeds, though final surface quality will depend on machining parameters and machine rigidity. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com