SDMT1204AZN-F57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, the WKP25S grade and the optimised F57 chipbreaker for reliable, productive steel and cast‑iron machining; order the insert directly via Metav Werkzeuge or consult the technical advisors for tailored process recommendations. SDMT1204AZN-F57 WKP25S milling indexable insert — Tiger·tec Silver coating, 15° free rake (Walter Tools) A SDMT1204AZN-F57 WKP25S is a square 90° milling insert engineered for high‑productivity roughing and finishing in steel and cast iron applications. Tiger·tec Silver coated grade WKP25S Square 90° insert, 12 mm size 15° free rake for stable cutting Optimised chipbreaker F57 for steel and cast iron Faster cycle times through consistent edge life The combination of the Tiger·tec Silver coating and the WKP25S grade provides a balance of wear resistance and thermal stability that translates into consistent edge life and longer tool life per index. For production environments where predictable tool performance reduces setup frequency, this indexable insert supports higher uptime and fewer unscheduled tool changes. The coated carbide substrate limits flank wear under typical steel cutting temperatures, meaning less variation in component tolerances over long runs and improved process reliability. Stable cutting and dependable chip control The integrated F57 chipbreaker is designed to break and evacuate chips reliably when machining P‑group (steel) and K‑group (cast iron) materials. Stable chip formation reduces the risk of re‑cutting and workpiece surface defects, which helps to maintain finishing quality even at elevated feed rates. Combined with the 15° free rake angle, the geometry reduces cutting forces in many common milling strategies, lowering spindle load and promoting a smoother cutting action in intermittent or interrupted cuts. Geometry and sizing for versatile setup integration The square 90° pocket fits a broad range of standard milling holders and indexable cutter bodies, while the 12 mm size and nominal thickness suit compact, rigid setups where stiffness is essential. The insert’s designation corresponds to established ISO geometry conventions, enabling straightforward selection and replacement in existing tool assemblies. For shops aiming to simplify inventory, the standard geometry supports cross‑compatibility across multiple tool families and reduces the variety of holders required. Application benefits: designed for steel and cast iron work Formulated for the thermal and abrasive demands of steel and cast iron, the grade’s coated carbide composition resists adhesive and abrasive wear pathways typical of these materials. In practice, this means fewer surface defects, more predictable tool changes and improved first‑pass yield in series production. The insert is especially effective in general-purpose face and shoulder milling operations where a balance of economy and performance is required. Contact Metav Werkzeuge today to specify Walter Tools Tiger·tec Silver inserts like the SDMT1204AZN-F57 WKP25S and receive personalised machining advice or order support by phone +49 2822 7131930 or email info@metav-werkzeuge.com. Technical data Article number: SDMT1204AZN-F57-WKP25S-WALTER Label: Fräswendeschneidplatte SDMT1204AZN-F57 WKP25S Walter Tools SKU: SDMT1204AZN-F57-WKP25S-WALTER Facts Size: 12 mm Thickness: 04 Free rake angle: 15° Shape: Square 90° Special features Series: Tiger·tec Silver Grade: WKP25S Chipbreaker: F57 Material suitability: Steel (P) / Cast iron (K) Execution: T Tolerance class: M ISO designation: SDMT1204AZN-F57 WKP25S FAQ What materials is this insert suitable for? The SDMT1204AZN-F57 WKP25S insert by Walter Tools is designed for steel (P) and cast iron (K) applications, delivering good wear resistance and chip control in both groups. Which chipbreaker is integrated and what is its benefit? The integrated F57 chipbreaker promotes secure chip formation and evacuation, reducing re‑cutting and helping to maintain surface quality when machining steel and cast iron with this milling insert. How does the 15° free rake affect machining? The 15° free rake reduces cutting forces and smooths the cutting action, which supports stable operation in interrupted cuts and helps to extend edge life of the insert. Is the insert compatible with standard toolholders? Yes; the square 90° geometry and ISO designation correspond to common milling indexable insert standards, allowing easy replacement in many established cutter bodies. What production benefits does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating increases thermal resistance and reduces flank wear, enabling longer tool life, fewer tool changes and more consistent part quality in serial production. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SDMT1204AZN-F57 WKP35G Wendeplatten - Walter Tools
The combination of the Tiger‑tec Gold coating and the WKP35G grade ensures durable performance and consistent chip control for milling steel and cast iron. Order the insert via Metav Werkzeuge or request application guidance from their consultants for optimal process integration. SDMT1204AZN-F57 WKP35G milling insert, Tiger‑tec Gold, 15° relief – Walter Tools A SDMT1204AZN-F57 WKP35G square 90° milling insert designed for productive machining of steel and cast iron in versatile milling operations Tiger‑tec Gold coating for long tool life Optimised F57 chipbreaker for chip control 15° relief angle for versatile milling Square 90° form with tolerance class M Longer tool life through optimised coating and grade The insert combines the Tiger‑tec Gold series with the WKP35G grade to provide a robust, coated carbide solution that resists abrasive wear and maintains a stable cutting edge. This results in fewer tool changes and higher machine utilisation, which directly supports improved process economy and predictable cycle times. The controlled coating architecture helps to reduce thermal and mechanical wear, translating into consistent quality across production batches and lower overall machining costs. Reliable chip control and surface quality for P and K materials Designed for materials in the ISO groups P (steel) and K (cast iron), the built-in F57 chipbreaker manages chip formation to prevent build-up and tool damage. For steel, the geometry promotes continuous chip flow and temperature control; for cast iron, the profile accommodates short, brittle chips. The outcome is enhanced surface finish and reduced manual rework. The chipbreaker concept is explained here: it shapes the chip as it forms so that evacuation from the cutting zone is faster and more reliable, improving process stability. Practical benefits in fixturing and repeatability The insert’s 15° relief angle and square 90° seating provide a versatile cutting geometry that suits a wide range of milling strategies, from slotting to face milling. The tolerance class M ensures consistent fit and repeatable positioning in standard toolholders, supporting high-precision setups and minimising positional variation between indexing operations. With a plate size of 12 and thickness 04 as specified, the indexable geometry enables reliable indexing and full use of the insert corners for cost-effective performance. For tailored application advice and availability of Walter Tools inserts contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for compatibility checks and stock information Technical Data SKU: SDMT1204AZN-F57-WKP35G-WALTER Label: Fräswendeschneidplatte SDMT1204AZN-F57 WKP35G Walter Tools Product type: Fräswendeschneidplatte (milling insert) Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WKP35G ISO designation: SDMT1204AZN-F57 WKP35G Specifications Relief angle: 15° Plate form: Square 90° Plate size: 12 Plate thickness: 04 Chipbreaker: F57 Tolerance class: M Applications & Features Applicable materials: Steel (P), Cast iron (K) Coated carbide grade for abrasive resistance Suitable for a range of milling operations Stable edge for repeatable performance FAQ What materials can be machined with this insert? The SDMT1204AZN-F57 WKP35G insert from Walter Tools is formulated for ISO groups P and K, which covers a broad range of steels and cast irons. What is the purpose of the F57 chipbreaker? The F57 chipbreaker on this insert promotes controlled chip formation and evacuation, improving surface finish and reducing the risk of tool or workpiece damage during milling. How does the Tiger‑tec Gold series benefit production? The Tiger‑tec Gold coating enhances wear resistance and thermal stability, helping to extend tool life and provide consistent performance across multiple workpieces. Is the 15° relief angle suitable for finishing and roughing? The 15° relief angle offers a good compromise between cutting strength and low cutting forces, making the insert suitable for a variety of milling strategies from finishing to more aggressive passes. Can the insert be indexed to use all corners? Yes; the square 90° form and the specified thickness and size allow indexing of multiple corners, which improves economy per cutting edge. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are used for explanatory purposes only and do not imply any affiliation with the manufacturers. The offered article is original, factory‑new goods of the manufacturer.
SDMT1204AZN-F57 WPP35G WPP35G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold coating and the WPP35G grade for high process reliability when machining steel; the chipbreaker F57 and 15° clearance combine to deliver consistent chip control and stable cutting. Order the insert directly via Metav Werkzeuge or contact the consultants for tailored advice. SDMT1204AZN-F57 WPP35G Milling Insert — Tiger·tec Gold, for Steel SDMT1204AZN-F57 WPP35G is a square 90° indexable milling insert designed for productive steel machining with optimised chip control and long tool life Tiger·tec Gold coated grade WPP35G Optimised chipbreaker F57 Square 90° form for versatile milling 15° clearance angle for stable cutting Consistent metal‑cutting performance and productivity gains The Tiger·tec Gold coating paired with the WPP35G grade offers a balanced combination of wear resistance and toughness tailored for steel (ISO group P). Designed specifically for the thermal and chip‑formation behaviour encountered when machining unalloyed and alloyed steel, this insert supports higher cutting parameters and longer tool life. The result is measurable productivity improvement and fewer tool changes in series production. Reliable chip control for safer machining The integrated chipbreaker F57 produces controlled chip shapes that reduce the risk of snarling and improve evacuation from the cut. This controlled chip formation helps to protect the workpiece surface and the tool seat, leading to fewer interruptions and a steadier machining cycle. The square 90° geometry contributes to robust radial support and predictable cutting behaviour on shoulder and face milling tasks. Designed geometry and clearance for stable cuts A 15° clearance on the rake/relief side reduces rubbing and heat buildup at the cutting edge while maintaining an effective engagement angle for general milling. The insert’s form and nominal dimensions — size 12 with thickness 04 and tolerance class M — provide repeatable positioning and compatibility with standard toolholders that accept SDMT-style inserts. This geometry promotes consistent dimensional results and good surface finish in demanding steel applications. Practical choice for workshop and production environments The indexable design means fast replacement and economical tooling management: edges can be rotated or changed without regrinding, lowering downtime and keeping set‑ups predictable. Being a coated cemented carbide grade from the Tiger·tec Gold family, the insert is suitable for a broad range of steels and is especially effective where a balance of wear resistance and toughness is required. The robust specification supports serial machining and offers a sound basis for process optimisation. For reliable, high‑productivity steel milling with Tiger·tec Gold technology, request availability and expert advice from Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 to discuss toolholder compatibility and cutting data. Technical data SKU: SDMT1204AZN-F57-WPP35G-WALTER Article designation: SDMT1204AZN-F57 WPP35G Label: Fräswendeschneidplatte SDMT1204AZN-F57 WPP35G Walter Tools Series: Tiger·tec Gold Grade: WPP35G Facts Insert size: 12 Thickness: 04 Form: Square 90° Clearance angle: 15° Chipbreaker: F57 Tolerance class: M Execution: T Special features Coating technology: Tiger·tec Gold Material application: Steel (ISO P) Coated cemented carbide grade Optimised chip control Robust geometry for face and shoulder milling Indexable insert type SDMT FAQ What materials is this insert suitable for? The SDMT1204AZN-F57 WPP35G is formulated for machining steel (ISO P); the Tiger·tec Gold coating and the WPP35G grade make it effective across unalloyed and alloyed steels. How does the chipbreaker F57 influence machining? The chipbreaker F57 creates controlled chips that improve evacuation and reduce snarl risk, which helps maintain a stable machining cycle with the SDMT1204AZN-F57 WPP35G insert. Which geometry advantages does the square 90° form provide? The square 90° form offers solid radial support and versatility for face and shoulder milling, enabling predictable engagement and good surface finish in steel applications. Can this insert handle interrupted cuts or heavy engagement? The combination of the WPP35G grade and Tiger·tec Gold coating provides toughness and wear resistance suitable for many demanding operations; selection should be confirmed against specific cutting parameters. What tolerance and fit can be expected? The insert is manufactured to tolerance class M, ensuring repeatable seating and interchangeability in compatible SDMT toolholders. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Walter Tools: The Walter AG (brand: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for clarification only; there is no connection between our company and the named brands. The offered article is original factory‑new goods of the manufacturer.
SDMT1204AZN-F57 WSM45X WSM45X Wendeplatten - Walter Tools
Take advantage of a WSM45X coated carbide grade and the F57 chipbreaker to ensure stable chip formation and long edge life when machining stainless steels and heat‑resistant alloys. Order the SDMT1204AZN‑F57 WSM45X directly via Metav Werkzeuge or ask our consultants if needed. SDMT1204AZN-F57 WSM45X — Milling insert (square 90°, 15° relief) by Walter Tools SDMT1204AZN-F57 WSM45X is a coated carbide milling insert engineered for productive machining of stainless steel and heat‑resistant superalloys in industrial milling applications. Coated carbide grade WSM45X Square 90° insert, 12 mm cutter size 15° clearance angle for secure cutting F57 chipbreaker for stable chip control High-performance grade for demanding materials The WSM45X grade is a coated carbide composition developed for the reliable machining of tough materials. Designed specifically for ISO group M (stainless steel) and S (heat‑resistant superalloys and titanium), the grade emphasises stable chip formation and thermal resistance to reduce built‑up edge. For production environments where repeatability and edge security are priorities, this insert supports longer intervals between indexings and fewer interrupted cycles, contributing to improved process efficiency and predictable component quality. Geometry engineered for consistent cutting and surface quality The square 90° shape combined with a 15° relief provides a robust cutting edge and good load distribution across the insert corner. The F57 chipbreaker controls chip flow and reduces risk of entanglement in deep or interrupted cuts, which helps maintain a steady surface finish and lowers the chance of tool damage. Medium tolerance class M ensures compatibility with standard toolholders, making integration into existing tool assemblies straightforward without additional adjustments. Productivity benefits and workflow integration With its focus on edge stability and chip control, the insert supports higher metal removal rates in many stainless steel and superalloy operations while keeping rework to a minimum. The design reduces cycle interruptions and simplifies inventory management through a well‑defined grade and chipbreaker pairing. Workshops aiming for consistent part quality and predictable tool life will find the insert a practical choice for serial production and specialised machining tasks, enhancing overall output and reducing unplanned downtime. Contact Metav Werkzeuge today to specify the SDMT1204AZN‑F57 WSM45X for your next production run or to request tailored application advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: SDMT1204AZN-F57-WSM45X-WALTER Article designation: SDMT1204AZN-F57 WSM45X Product type: Fräswendeschneidplatte Manufacturer: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Facts Relief angle: 15° Insert form: Square 90° Insert size: 12 Thickness: 04 Tolerance class: M Chipbreaker: F57 Special features Grade: WSM45X (coated carbide) Material application: stainless steel (ISO group M) Also suitable for: heat‑resistant superalloys and titanium (ISO group S) Execution: T Series and sort description included FAQ What materials is this insert suitable for? The SDMT1204AZN‑F57 WSM45X insert is designed primarily for stainless steel (ISO group M) and can also be used on heat‑resistant superalloys and titanium (ISO group S) depending on component and process parameters. How does the F57 chipbreaker affect machining? The F57 chipbreaker provides controlled chip formation and evacuation, improving surface quality and reducing the likelihood of chip interference during milling with the SDMT1204AZN‑F57 WSM45X. What are the main geometric advantages of this insert? A square 90° shape and a 15° clearance angle deliver a robust corner for high radial loads, stable cutting edges and consistent results in interrupted or heavy milling operations with the SDMT1204AZN‑F57 WSM45X. Is the SDMT1204AZN‑F57 compatible with standard toolholders? Yes, the insert’s form and tolerance class M mean it is compatible with commonly used toolholders for indexable milling inserts, facilitating straightforward integration into existing tooling systems. Which production environments benefit most from this grade? Serial production, job shops and aerospace or medical subcontractors machining stainless steel and high‑temperature alloys will benefit from the stable edge life and predictable performance of the SDMT1204AZN‑F57 WSM45X. Manufacturer: Walter Tools (Walter AG); Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SDMT1204AZN-F57 WSP45G WSP45G Wendeplatten - Walter Tools
The combination of Tiger·tec Gold coating and the WSP45G grade ensures reliable chip control and extended edge life for a wide range of materials; paired with the robust square 90° geometry and a 15° free angle, this yields stable, repeatable milling performance. Order the SDMT1204AZN-F57 WSP45G directly via Metav Werkzeuge or ask our consultants if needed. SDMT1204AZN-F57 WSP45G indexable milling insert by Walter Tools — Tiger·tec Gold, 15° free angle SDMT1204AZN-F57 WSP45G is a square indexable milling insert designed for versatile milling applications across steels, stainless steel and high-temperature alloys, featuring a Tiger·tec Gold coating and a dedicated F57 chipbreaker Tiger·tec Gold PVD coating Versatile P/M/S material range Square 90° form, 15° free angle F57 chipbreaker for stable chips High process reliability across demanding materials The coated grade from the Tiger·tec Gold family provides a resilient cutting edge that is optimised for the typical heat and chip behaviour of steels and stainless steel as well as for heat-resistant alloys and titanium. Thanks to the WSP45G formulation, the insert supports secure chip formation and reduced edge build-up, which translates into fewer interruptions and a steadier production rhythm. These material-oriented properties deliver predictability in cycle times and surface quality even in mixed production runs. Consistent chip control and extended tool life The dedicated F57 chipbreaker promotes short, controllable chips under a wide range of cutting conditions, reducing the risk of recutting and improving surface finish. Combined with the coated cemented carbide substrate, the geometry and coating synergy reduce flank wear and maintain a stable cutting edge. The square 90° shape and a 15° free angle contribute to robust corner strength and moderate cutting forces, supporting longer intervals between index changes and minimising setup downtime. Smooth integration and reliable repeatability in milling setups With its ISO-style designation and compact format, the insert fits standard milling cutters and indexable tool bodies with predictable location and repeatability. The tolerance class M ensures consistent interchangeability between batches, aiding process planners and operators in maintaining tool offsets and minimising recalibration. As an indexable milling solution, it supports efficient inventory management and rapid replacement, helping to keep spindle uptime high and toolroom logistics straightforward. Discuss specific cutting parameters with Metav Werkzeuge for optimal results with this Walter Tools grade and to align insert choice with component requirements Technical Data Article number: SDMT1204AZN-F57-WSP45G-WALTER Product name: Fräswendeschneidplatte SDMT1204AZN-F57 WSP45G Walter Tools Manufacturer: Walter Tools Series: Tiger-tec Gold Facts Free angle: 15° Plate size: 12 Plate thickness code: 04 Plate form: Quadrat 90° Special features Chipbreaker: F57 Grade: WSP45G Material applicability: P / M / S Tolerance class: M Execution: T ISO designation: SDMT1204AZN-F57 WSP45G FAQ What materials is this insert suitable for? The SDMT1204AZN-F57 WSP45G is suitable for machining P (steel), M (stainless steel) and S (heat-resistant superalloys and titanium), offering tailored performance for each group. How does the Tiger·tec Gold coating benefit cutting performance? The Tiger·tec Gold coating improves thermal and wear resistance, helping the WSP45G grade to maintain a stable cutting edge and extend tool life under typical milling conditions. What advantages does the F57 chipbreaker provide? The F57 chipbreaker produces short, consistent chips that reduce the risk of recutting and support a better surface finish, making the insert particularly useful in mixed and interrupted cuts. Is the geometry suitable for heavy-duty milling? The square 90° form and a 15° free angle deliver strong corner support and moderate cutting forces, which together are well suited for robust milling tasks and contribute to predictable edge life. How does the tolerance class affect tool interchangeability? Tolerance class M ensures consistent dimensions and location accuracy between inserts, simplifying indexing and reducing the need for frequent tool offset adjustments. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. References to brand names are for explanatory purposes only and indicate original, factory-new goods from the manufacturer. There is no affiliation between Metav Werkzeuge and the mentioned brands.
SDMT1204ZDR-D57 WKP35G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating and the WKP35G grade for stable cutting and predictable tool life; the square 90° geometry with a 15° relief angle and the D57 chipbreaker ensure controlled chip formation in steel and cast iron. Order or request technical advice via Metav Werkzeuge for fast supply and application support. SDMT1204ZDR-D57 WKP35G milling insert — Walter Tools (Tiger·tec Gold, square 90°) The SDMT1204ZDR-D57 WKP35G is a coated carbide milling insert designed for productive machining of steel and cast iron in general milling applications. Tiger·tec Gold coating for stable cutting WKP35G grade optimised for steel and cast iron Square 90° insert with 15° relief angle D57 chipbreaker for controlled chip formation Higher throughput through consistent edge stability The combination of the Tiger·tec Gold coating and the WKP35G grade delivers a balance of wear resistance and thermal stability that supports longer tool life and fewer indexings. The advanced coating reduces abrasive and adhesive wear, which translates into more consistent cutting-edge geometry over extended production runs. For operations that prioritise cycle-time reliability, this insert reduces unexpected downtime and helps maintain part tolerances with predictable tool-change intervals. Controlled chip formation for safer, faster milling The D57 chipbreaker is engineered to produce short, manageable chips when machining ISO group P (steel) and K (cast iron) materials. Controlled chips improve surface finish and reduce the risk of entanglement, contributing to safer unattended machining and faster cycle times. In practical terms, the chip geometry reduces secondary operations for chip disposal and minimises rework caused by poor chip evacuation. Robust geometry for versatile milling tasks A square 90° cutting geometry provides four indexed cutting edges per insert and is suitable for a wide range of face and shoulder milling operations. The 15° relief angle aids in reducing cutting forces and helps to avoid rubbing on the workpiece, while the nominal size 12 and thickness 04 format ensure mechanical stability in standard Walter milling cutters. The insert’s tolerance class M supports interchangeability between toolholders and repeatable set-up across tool changes, which is particularly valuable in batch production. Clear benefits for process security and productivity Adopting this coated carbide insert reduces machining variability and supports consistent surface quality, which is an economic advantage in medium- to high-volume production. The design focuses on efficient heat management and reliable chip control so that feed and speed can be exploited more aggressively where the machine and clamping allow. For production engineers seeking reproducibility and a wide material capability, the specification of this insert allows straightforward tool selection and less experimental set-up time. For fast technical advice or to secure supply of the Walter Tools SDMT1204ZDR-D57 WKP35G milling insert, contact Metav Werkzeuge for application consultation and order fulfilment via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: SDMT1204ZDR-D57-WKP35G-WALTER Article: SDMT1204ZDR-D57 WKP35G Product type: Milling insert Series: Tiger·tec Gold Grade: WKP35G Geometry: Square 90° Relief angle: 15° Chipbreaker: D57 Thickness: 04 Size: 12 Tolerance class: M Designation: T Applicable materials: P / K Numbers / Core technical data Relief angle: 15° Size: 12 Thickness: 04 Tolerance class: M Four cutting edges per insert Chipbreaker designation: D57 Special features / Versions Coating: Tiger·tec Gold (coated carbide) Grade suited for steel and cast iron Square 90° insert form WKP35G: coated cemented carbide grade Design optimised for stable chip formation FAQ Is this insert suitable for machining steel? Yes. The SDMT1204ZDR-D57 WKP35G insert from Walter Tools is optimised for ISO group P materials (steel) and offers a coating and grade combination designed to handle the typical heat and chip characteristics of steel machining. Can the insert be used on cast iron? Yes. The WKP35G grade and the D57 chipbreaker make the insert suitable for cast iron (ISO group K), providing controlled chip breaking and good wear behaviour on abrasive materials. What does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating improves thermal resistance and wear protection, supporting longer tool life and more consistent cutting-edge performance under cyclic production loads. Why is the square 90° geometry beneficial? A square 90° geometry supplies four indexable cutting edges per insert, enabling efficient edge rotation and reduced tooling costs per indexed edge while offering versatile use in face and shoulder milling. What advantage does the D57 chipbreaker offer? The D57 chipbreaker promotes short, controllable chips during milling of steel and cast iron, improving surface finish, reducing chip-related faults, and enhancing machine uptime. Manufacturer: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned only for explanatory purposes. There is no connection between our company and the mentioned brands. The offered item is original, brand-new goods from the manufacturer.
SDMT1204ZDR-D57 WPP35G WPP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the WPP35G grade for sustained cutting performance on steel; the square 90° form with a 15° clearance ensures reliable chip control and repeatable results. Order the insert directly via Metav Werkzeuge or contact the consultants for application advice. SDMT1204ZDR-D57 WPP35G indexable milling insert – Tiger·tec Gold, 15° clearance, square 90° (Walter Tools) SDMT1204ZDR-D57 WPP35G is a coated indexable milling insert designed for productive machining of steel in serial and universal applications Tiger·tec Gold coating for long tool life WPP35G grade optimised for steel machining Square 90° geometry for stable, versatile milling Chipbreaker D57 for consistent chip formation Greater productivity through proven coating and grade The combination of Tiger·tec Gold technology and the WPP35G carbide grade delivers a measurable improvement in tool life and process stability when machining steel. The advanced coating reduces friction and thermal load, which in turn extends cutting edge durability and allows for higher cutting volumes between index changes. For production environments seeking reproducible results, this insert offers a rational upgrade that reduces downtime and tool handling. Reliable chip control and edge stability for consistent surface quality Designed with a chipbreaker D57 and a square 90° plate form, the insert ensures controlled chip flow and lower cutting forces in a range of milling operations. The 15° clearance optimises the cutting geometry to avoid rubbing and promote a clean shear, which helps to maintain consistent surface finish and dimensional accuracy. These features translate into fewer rejects and more predictable cycle times on steel components. Versatility for steel applications and straightforward process integration The insert is specified for the material group P and is suitable for unalloyed and alloyed steel grades, covering both universal and tougher cutting scenarios. Its standardised ISO designation simplifies tool selection and inventory management in a workshop or production line. Integration into existing toolholders is straightforward thanks to the common plate size and form, allowing seamless adoption into mixed-machining fleets. Practical benefits for shop-floor efficiency and cost control By using a coated, grade-optimised insert, the workshop benefits from lower tool consumption and reduced changeover frequency. The coated carbide substrate resists flank wear and supports stable cutting at elevated feed rates, contributing to a better cost-per-part outcome. Maintenance routines are simplified through predictable wear patterns, which aids planning and reduces unexpected stoppages. Contact Metav Werkzeuge for a tailored recommendation on Walter Tools inserts and to discuss suitable cutting parameters or stocking options Technical data Article number: SDMT1204ZDR-D57-WPP35G-WALTER Label: Fräswendeschneidplatte SDMT1204ZDR-D57 WPP35G Walter Tools Manufacturer: Walter Tools Product type: Fräswendeschneidplatte ISO designation: SDMT1204ZDR-D57 WPP35G Facts Clearance angle: 15° Plate form: Square 90° Plate size: 12 mm Plate thickness: 04 Tolerance class: M Special features Series: Tiger·tec Gold Grade: WPP35G (coated carbide) Chipbreaker: D57 Execution: T Material group suitability: Steel (P) Product UID: SDMT1204ZDR-D57-WPP35G-WALTER FAQ What materials is this insert intended for? The SDMT1204ZDR-D57 WPP35G insert is specified for material group P and is tailored for machining various steel grades. How does the Tiger·tec Gold coating benefit machining? The Tiger·tec Gold coating reduces friction and thermal load, improving edge life and enabling more stable cutting conditions with the WPP35G grade. Is the insert suitable for high-volume production? Yes; the combination of WPP35G grade and the D57 chipbreaker provides consistent chip control and repeatable wear behaviour suited to serial production. Can the SDMT1204ZDR-D57 WPP35G be used in standard toolholders? The ISO designation and square 90° form allow straightforward fitting into compatible milling cutters and standard indexable tool systems. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SDMT1204ZDR-D57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of a Tiger·tec Gold PVD-coated grade and a dedicated D57 chipbreaker for consistent chip control and long life in demanding milling applications; order directly via Metav Werkzeuge or contact our technical advisers for process-matched recommendations. SDMT1204ZDR-D57 WSP45G milling insert – Tiger·tec Gold, D57 chipbreaker by Walter Tools The SDMT1204ZDR-D57 WSP45G is a square 90° milling insert with a 15° clearance, engineered for robust milling of steels, stainless steels and heat‑resistant alloys. Tiger·tec Gold coated carbide for long tool life Applicable to Steel, Stainless steel and Superalloys D57 chipbreaker for controlled chip formation Square 90° form with 12 mm edge length Consistent edge stability and wear resistance for productive milling The Walter Tools grade from the Tiger·tec Gold series combines a coated carbide substrate with a PVD finish to provide a balance of toughness and hardness that supports longer cutting edge life. With the D57 chipbreaker, the insert promotes stable chip formation across a range of cutting conditions, reducing the risk of built‑up edge and unexpected tool failure. These characteristics translate into fewer tool changes and a steadier process window, which is particularly valuable in medium‑ and high‑volume production environments where cycle time reliability is crucial. Broad material capability keeps setups simple and flexible Designed for the ISO groups P/M/S, the insert addresses conventional steels, stainless steel and heat‑resistant superalloys or titanium workpieces. The designation P/M/S refers to the typical material behaviour during cutting — from standard steel chip formation to the adhesive tendencies and heat challenges of stainless steel, and the thermal and chemical demands of superalloys. The combination of the 15° clearance angle and the square 90° form provides a robust cutting edge that resists chipping while enabling conservative profile machining or heavier engagement when required. Efficiency gains through reduced downtime and improved surface quality Process planners will value the insert’s contribution to machining economy: the WSP45G composition preserves cutting edge integrity under thermal load, which supports consistent surface finish and dimensional stability across multiple parts. By maintaining a predictable wear pattern and stable chip evacuation, the insert helps to lower scrap rates and short‑term interruptions. In practice, this means operators can plan longer tool cycles and achieve a more favourable balance between productivity and component quality. Dimensional and mounting information for reliable setup Key dimensional details support straightforward tool selection: edge length 12 mm, thickness 04, clearance 15° and tolerance class M. The square 90° geometry gives four usable edges per indexable plate and a solid contact area in the pocket for secure clamping. The grade WSP45G is PVD‑coated and suited to a wide span of feeds and speeds; pairing the insert with an appropriate cutter body that accepts SDMT indexable plates ensures correct rake and run‑out control. For advice on matching holders or feed/speed windows, consult our technical team. Contact Metav Werkzeuge for tailored recommendations on Walter Tools Tiger·tec Gold inserts and to discuss compatible cutter bodies, cutting data and availability. Technical Data Article number: SDMT1204ZDR-D57-WSP45G-WALTER Product name: SDMT1204ZDR-D57 WSP45G Series: Tiger·tec Gold Grade: WSP45G Manufacturer: Walter Tools Data Edge length: 12 mm Clearance angle: 15° Thickness: 04 Shape: Square 90° Tolerance class: M Special features Coating: PVD (Tiger·tec Gold) Substrate: Coated carbide Applicable materials: Steel (P), Stainless steel (M), Superalloys/Titanium (S) Chipbreaker: D57 Execution: T FAQ What materials can this insert machine effectively? The SDMT1204ZDR-D57 WSP45G insert is formulated for P/M/S groups: machined components in steel, stainless steel and heat‑resistant superalloys or titanium are all within its intended application range. How does the D57 chipbreaker affect cutting performance? The D57 chipbreaker controls chip geometry to improve evacuation and reduce the chance of entanglement; this stabilises cutting forces and supports a consistent surface finish when using the WSP45G grade. How many cutting edges are available per insert and what is the geometry? The square 90° form provides four indexable edges; the plate’s robust contact face and 15° clearance assist secure seating in compatible cutter bodies and resist edge chipping under load. Is the WSP45G grade suitable for continuous high‑temperature cutting? Yes; the Tiger·tec Gold PVD coating and the WSP45G substrate improve thermal resistance and edge life in demanding thermal conditions typical of stainless steels and superalloys. What dimensional details are relevant when selecting the corresponding toolholder? Important dimensions are edge length 12 mm, thickness 04, and the SDMT contour (SDMT1204ZDR‑D57); ensure the cutter body accepts SDMT plates and matches the plate’s tolerance class M. Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen; Germany Protected trademarks and product names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation. There is no connection between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer.
SDMW06T204-A57 WKP25S Wendeplatten - Walter Tools
Benefit from the combination of the WKP25S grade and Tiger·tec Silver coating together with a square 90° form and 0.4 mm corner radius for dependable, repeatable milling results; order via Metav Werkzeuge or consult the technical team for specification support. SDMW06T204-A57 WKP25S milling insert (square 90°, 15° clearance) — Walter Tools SDMW06T204-A57 WKP25S is a coated carbide milling insert designed for productive steel and cast-iron machining in industrial milling operations Tiger·tec Silver coated carbide grade WKP25S Optimised for steel and cast iron machining Square 90° format with 0.4 mm corner radius 15° clearance angle for general-purpose milling Higher metal-removal rates through a wear-resistant grade The Tiger·tec Silver technology combined with the WKP25S grade provides a balance between wear resistance and toughness that favours higher material removal rates when machining steel and cast iron. The coated carbide construction reduces flank wear and extends edge life under typical milling temperatures, which means fewer insert changes and longer uninterrupted runs on production tooling. Engineers benefit from consistent cutting performance and reduced process variability, supporting predictable cycle times and more reliable throughput. Consistent chip control for improved surface finish A dedicated chipbreaker A57 and the square 90° geometry ensure stable chip formation and evacuation during interrupted and continuous cuts. The 0.4 mm corner radius supports a stronger edge for roughing passes while still enabling acceptable surface quality in finishing steps. This combination improves tool-life economy and reduces the risk of tool-induced marks on the workpiece, making the insert suitable for demanding workshop environments where repeatable surface integrity is required. Simple integration with standard toolholders to raise productivity The insert’s form code (size 06, thickness T2) and a 15° clearance angle make it compatible with a wide range of standard milling holders used in industrial settings. The tolerance class M ensures interchangeability and repeatability when replacing inserts, reducing setup time and minimising alignment checks. As a result, the component supports efficient tool-change routines and straightforward inventory management, promoting leaner production processes and faster turnaround for batch and single-piece production alike. For procurement or technical clarification on the Walter Tools Tiger·tec Silver SDMW06T204-A57 WKP25S insert, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 for tailored advice and ordering support Technical data SKU: SDMW06T204-A57-WKP25S-WALTER Article name: SDMW06T204-A57 WKP25S Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WKP25S Core data Corner radius: 0.4 mm Clearance angle: 15° Plate form: Square 90° Plate size: 06 Thickness: T2 Tolerance class: M Special features Coating technology: Tiger·tec Silver Chipbreaker: A57 Material groups: P (steel), K (cast iron) Substrate: coated carbide Application: milling indexable insert Execution: W FAQ What materials is the insert suitable for? The SDMW06T204-A57 WKP25S insert is designed for steel (P) and cast iron (K) applications, utilising the Tiger·tec Silver coating and WKP25S grade for these material groups. Which chipbreaker does the insert use and why does it matter? The insert uses the A57 chipbreaker; this feature improves chip control and evacuation, helping to maintain stable cutting conditions and consistent surface finish during milling. How does the 0.4 mm corner radius affect cutting performance? A 0.4 mm corner radius strengthens the cutting edge for roughing operations while still allowing acceptable finish quality, reducing edge chipping and extending effective tool life. Is the insert compatible with standard milling holders? Yes. The size 06 format and T2 thickness, combined with the square 90° form and 15° clearance, make the insert compatible with many common industrial milling toolholders. What advantage does the Tiger·tec Silver series provide? Tiger·tec Silver offers an optimised coated-carbide solution that balances wear resistance and toughness, improving process stability and extending service life under typical steel and cast-iron cutting conditions. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered article is an original, factory‑new product of the respective manufacturer. The brand for this product is Walter Tools.
SDMW06T204-A57 WKP35G Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Gold coating for longer tool life, the WKP35G grade tuned for steel and cast iron, and a precise 15° relief with a 0.4 mm corner radius for stable, repeatable milling results; order the SDMW06T204-A57 WKP35G insert directly via Metav Werkzeuge or consult the specialists if further application data is required. SDMW06T204-A57 WKP35G — Milling insert, Tiger‑tec Gold coating, for steel and cast iron (Walter Tools) The SDMW06T204-A57 WKP35G is a square 90° milling insert engineered for productive general milling of steel and cast iron, combining a robust coated-carbide grade with a chipformer optimised for consistent chip control. Tiger‑tec Gold coated for enhanced wear resistance WKP35G grade optimised for steel and cast iron 15° relief angle for stable cutting Square 90° form with 0.4 mm corner radius Consistent material performance that reduces rework The combination of the WKP35G carbide grade and Tiger‑tec Gold coating delivers a stable cutting edge suited to the typical thermal and abrasive conditions of machining steel (ISO P) and cast iron (ISO K). The coated-carbide chemistry and multilayer technology reduce flank wear and support longer tool life under moderate to demanding cutting conditions. The integrated A57 chipformer is engineered to promote predictable chip breakage and evacuation, which helps to lower the risk of interrupted cuts and aids surface quality—translating into fewer rejects and less rework per production batch. Geometry designed for predictable surface finish and edge security A square 90° insert geometry combined with a 0.4 mm corner radius increases edge strength for roughing while still enabling acceptable surface finish in semi-finishing passes. The 15° relief angle reduces rubbing on the flank and assists chip flow, improving tool stability and reducing cutting forces. With a tolerance class of M, the insert offers consistent dimensions for repeatable set-up and predictable runout behaviour, which supports process reliability in serial manufacturing environments. Productivity and cost-efficiency through process security The insert’s coated grade and geometry target a balance between wear resistance and fracture toughness, which is vital when alternating between unalloyed and alloyed steels or encountering abrasive cast iron. This balance supports higher productivity through longer intervals between indexings and less frequent tool changes. The designation in the Tiger‑tec Gold series signals enhanced resistance to common wear mechanisms, enabling a better total cost of ownership in many milling operations where stable cutting conditions and repeatable part quality are priorities. Seamless integration into standard milling tool systems Designed in the SDMW06 format with thickness T2 and a compact 06 size, the insert fits toolholders that accept SDMW06‑format indexable inserts, enabling easy integration into existing tool sets without extensive requalification. The square 90° shape provides flexible cutting edge utilisation across corners, and the compact insert size is especially suitable for medium‑duty milling applications where both rigidity and edge life are required. Compatibility with standard clamping systems simplifies stockkeeping and shortens set-up times on the shop floor. For secure, high-productivity milling with Walter Tools’ Tiger‑tec Gold technology, contact Metav Werkzeuge to order the SDMW06T204-A57 WKP35G insert or to request application advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: SDMW06T204-A57-WKP35G-WALTER SKU: SDMW06T204-A57-WKP35G-WALTER Label: Fräswendeschneidplatte SDMW06T204-A57 WKP35G Walter Tools Facts Relief angle: 15° Corner radius: 0.4 mm Insert size: 06 Thickness: T2 Tolerance class: M Special features Coating: Tiger‑tec Gold Grade: WKP35G (coated carbide) Chipformer: A57 Insert shape: square 90° Material suitability: steel (ISO P), cast iron (ISO K) Series: Tiger‑tec Gold Manufacturer: Walter Tools FAQ What materials is this insert suitable for? The SDMW06T204-A57 WKP35G insert is engineered for steel (ISO P) and cast iron (ISO K) applications thanks to the WKP35G grade and the Tiger‑tec Gold coating. How does the Tiger‑tec Gold coating benefit tool life? Tiger‑tec Gold on the WKP35G grade enhances wear resistance and reduces flank degradation, which typically extends the service life of the insert in repetitive milling operations. What does the A57 chipformer provide? The A57 chipformer improves chip control and evacuation for predictable chip breakage, helping to maintain surface quality and reduce the chance of chip‑related interruptions. Is the geometry suitable for both roughing and finishing? The square 90° shape with a 0.4 mm corner radius offers edge strength for roughing while allowing acceptable surface finish in semi‑finishing, making the insert versatile for mixed‑operation workflows. Which toolholders are compatible with this insert format? The insert conforms to the SDMW06 format and is intended for toolholders designed to accept SDMW06‑format indexable inserts, facilitating straightforward retrofitting into existing tool systems. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SDMW06T204-A57 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, the WKP35S grade and a robust square 90° geometry for consistent tool life and stable chip control; order directly via Metav Werkzeuge or consult the team for cutting data and application advice. SDMW06T204-A57 SDMW06T204-A57 WKP35S milling insert WKP35S — for steel and cast iron, Walter Tools The SDMW06T204-A57 WKP35S is a square 90° milling insert designed for productive machining of steels and cast irons, delivering wear resistance and reliable chip control in general milling operations. Tiger·tec Silver coated for long tool life WKP35S grade optimised for steel and cast iron Square 90° insert with 0.4 mm corner radius 15° clearance angle for secure cutting geometry High wear resistance for demanding steels and cast iron machining The Tiger·tec Silver coating combined with the WKP35S carbide grade provides a balance of surface hardness and thermal stability that supports long tool life under standard to elevated cutting temperatures. This composition is particularly effective when machining a wide range of steels and cast irons: the coating improves abrasion resistance while the substrate grade maintains a robust cutting edge. As a consequence, the insert reduces the frequency of tool changes and contributes to steady production output. Geometry that stabilises the cut and improves edge security The insert’s square 90° form together with a 0.4 mm corner radius and a 15° clearance angle create a cutting geometry that resists edge chipping and offers consistent radial engagement. The defined corner radius supports moderate edge strength for general milling tasks, while the clearance angle ensures controlled shear and reduced rubbing on the flank. The result is predictable surface finish and repeatable dimensional performance in operations where stability is essential. Efficiency gains through targeted grade selection and material compatibility Designed for ISO groups P (steel) and K (cast iron), the grade is tuned to typical chip formation and thermal loads encountered in these materials. The combination of substrate and coating translates into fewer interrupted cycles for insert changes and a lower tooling cost per part in many production scenarios. As the grade is catalogue- and geometry-dependent in its exact application range, it reliably supports productive cutting strategies when matched to appropriate feed and speed recommendations. Practical machining guidance and application scope This insert is intended for general milling duties where robustness and dependable wear resistance are priorities. The A57 chipbreaker is suited to common chip forms in steels and cast irons; for specific operations—such as high-feed milling or finishing—tooling geometry and cutting data should be matched to the application. If the machining task involves atypical alloys or strict surface finish requirements, consult the technical data sheet or speak with Metav Werkzeuge for tailored recommendations and verified cutting parameters. For process-critical milling with Walter Tools’ Tiger·tec Silver inserts, contact Metav Werkzeuge for application advice and supply at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 Technical Data Article number: SDMW06T204-A57-WKP35S-WALTER Product type: milling insert Series: Tiger·tec Silver Grade: WKP35S Manufacturer: Walter Tools Facts Insert shape: square 90° Clearance angle: 15° Corner radius: 0.4 mm Plate size: 06 Plate thickness: T2 Tolerance class: M Special features Chipbreaker: A57 Execution: W Material suitability: P (steel), K (cast iron) Geometry-dependent main applications Coated carbide (Tiger·tec Silver technology) FAQ What materials is this insert best suited for? The SDMW06T204-A57 WKP35S insert is optimised for steels and cast irons (ISO groups P and K) and its WKP35S grade targets typical chip formation and wear mechanisms in these materials. How does the Tiger·tec Silver series improve performance? Tiger·tec Silver coating enhances abrasion resistance and thermal stability, allowing the WKP35S grade to maintain edge integrity longer under standard milling conditions. What does the 0.4 mm corner radius mean for machining? A 0.4 mm corner radius balances edge strength and surface finish: it provides improved durability over a sharp corner while maintaining acceptable finish for general milling tasks. Can this insert be used for finishing passes? The insert is primarily designed for general productive milling; finishing applications depend on machine rigidity and cutting parameters—select appropriate feeds, speeds and possibly a smaller corner radius for fine finishing. Is the chipbreaker A57 suitable for cast iron? Yes, the A57 chipbreaker is designed to handle the short, often breaking chips typical of cast iron machining and supports stable chip evacuation in many milling scenarios. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanatory purposes and do not imply any affiliation with our company. The offered item is original, factory-new goods of the manufacturer.
SDMW09T308-A57 WKP25S Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Silver coating and the WKP25S grade for prolonged edge life and consistent chip control; the 15° clearance and square 90° geometry deliver reliable cutting performance and predictable tool behaviour. Order the insert directly via Metav Werkzeuge or consult our specialists for application support. SDMW09T308-A57 WKP25S milling insert — Tiger‑tec Silver for steel and cast iron, Walter Tools A SDMW09T308-A57 WKP25S milling insert engineered for robust machining of steel and cast iron, with a 15° clearance and square 90° geometry for stable engagement. Tiger‑tec Silver coating for high wear resistance Optimised for steel and cast iron machining Square 90° form with 0.8 mm corner radius Consistent edge life that keeps production running The combination of the Tiger‑tec Silver coating and the WKP25S carbide grade is designed to extend tool life under the thermal and abrasive loads typical of steel and cast iron milling. The coated carbide reduces flank wear and helps maintain a stable cutting edge over longer production runs, which translates into fewer tool changes and higher uptime. This performance is particularly relevant for shops seeking predictable costs per component and a dependable process window for serial production. Precision geometry for controlled chips and surface quality The insert’s 15° clearance and its square 90° form deliver controlled entry angles and robust support at the cutting edge, reducing vibration and improving dimensional repeatability. The 0.8 mm corner radius provides a balance between strength and surface finish: a larger radius increases edge resilience and is beneficial for interrupted cuts, while the specified radius still permits good surface quality. The integrated A57 chipformer is configured to break and evacuate chips efficiently during face and profile milling; for those unfamiliar, a chipformer is a small geometry on the insert face that influences chip shape and flow, reducing heat build‑up and protecting the edge. Broad material capability with practical handling benefits Classified for material groups P (steel) and K (cast iron), this insert is suitable across a wide range of unalloyed and alloyed steels as well as common cast iron grades, making it a versatile choice for mixed‑batch production environments. The plate’s size designation 09, thickness T3 and tolerance class M ensure repeatable seating and compatibility with standard indexable milling toolholders, simplifying inventory and cutter set‑up. Walter Tools’ geometry and coating approach aim to offer process stability and predictable tool life, helping to reduce scrap rates and improve throughput in daily workshop practice. Contact Metav Werkzeuge for Walter Tools Tiger‑tec Silver inserts and tailored application advice via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: SDMW09T308-A57-WKP25S-WALTER Name: SDMW09T308-A57 WKP25S Type: Milling insert Brand: Walter Tools Core dimensions Free cutting angle: 15° Corner radius: 0.8 mm Plate size: 09 Thickness: T3 Square angle: 90° Tolerance class: M Special features Series: Tiger‑tec Silver Grade: WKP25S (coated carbide) Chipformer: A57 Material groups: P (steel), K (cast iron) Geometry: Square 90° Execution: W FAQ Which materials is this insert suited for? The SDMW09T308-A57 WKP25S insert is specified for steel (group P) and cast iron (group K), reflecting the WKP25S grade and Tiger‑tec Silver coating optimised for these material families. What benefit does the A57 chipformer provide? The A57 chipformer promotes reliable chip breaking and evacuation during milling, which reduces heat concentration at the cutting edge and supports consistent surface finish when using the SDMW09T308-A57 WKP25S. How does the 0.8 mm corner radius influence performance? A 0.8 mm radius increases edge strength and supports interrupted cutting conditions while still permitting a satisfactory surface quality; it helps balance edge life and finish in typical milling operations. Is this insert compatible with standard square milling cutters? Yes, the square 90° form and tolerance class M make the insert suitable for standard indexable square milling cutter bodies that accept the SDMW09T308‑type geometry. Can the SDMW09T308-A57 WKP25S be used on stainless steel? Use on stainless steel is not specified for this grade in the available data; the insert is optimised for steel and cast iron, so an alternative grade should be selected for reliable stainless‑steel performance. Manufacturer: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SDMW09T308-A57 WKP35G Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance, precise geometry and reliable chip control for improved machining consistency and lower tooling costs; order the insert directly via Metav Werkzeuge or request tailored cutting data from our consultants. Fräswendeschneidplatte SDMW09T308-A57 WKP35G — Square milling indexable insert with Tiger·tec Gold coating by Walter Tools Fräswendeschneidplatte SDMW09T308-A57 WKP35G is a square indexable insert designed for efficient milling of steel and cast iron, featuring a robust coated carbide grade and a dedicated chipbreaker for controlled swarf evacuation Tiger·tec Gold coated for high wear resistance WKP35G grade tuned for steel and cast iron Square 90° form with 0.8 mm corner radius Chipbreaker A57 for predictable chip control Consistent productivity through optimised coating and grade The combination of the Tiger·tec Gold coating and the WKP35G carbide grade results in a durable cutting edge that sustains performance over extended runs. This coating technology is engineered to resist abrasive wear and to maintain a sharp edge under the thermal and mechanical loads typical when machining steel and cast iron. As a result, shops benefit from fewer interruptions for insert changes and more consistent part quality across batches. The insert’s metallurgy and coating support higher effective cutting lengths and reduced frequency of tool replacement, which contributes directly to lower manufacturing overheads and improved uptime. Stable geometry for repeatable surface quality The insert’s square 90° form and 0.8 mm corner radius produce a reliable cutting geometry that aids in repeatable surface finish and dimensional control. The 15° clearance angle reduces rubbing on the flank and facilitates smooth entry and exit from the cut, while the tolerance class M ensures consistent dimensions between indexable edges. These geometric qualities are particularly valuable in series production where repeatability is essential: operators achieve predictable tool engagement, and process engineers can set feeds and speeds with confidence, reducing variability in cycle times and finished-part quality. Controlled chip formation and economical machining Equipped with the chipbreaker A57, this insert delivers predictable chip segmentation and evacuation, reducing the risk of entanglement and tool damage. Controlled swarf formation leads to safer machining conditions and enables more stable cutting parameters, which can translate into faster material removal rates and improved tool life. The insert’s design therefore supports a rational cost-benefit profile: fewer scrap parts, less machine downtime, and a lower cost per component thanks to extended edge life and reliable chip control during both roughing and semi-finishing operations. Practical integration and application-focused design The designation SDMW09T308-A57 WKP35G denotes a widely used indexable geometry that integrates with standard milling toolholders for square inserts. The T3 plate thickness and the execution code W indicate a robust configuration suitable for general-purpose slotting and face milling tasks where a balance between strength and accessibility is required. Given its focus on P / K materials (steel and cast iron), the insert is suitable for mixed-production environments that demand flexibility without sacrificing productivity. Technical teams will find the insert straightforward to specify for programmes where consistent edge performance and reliable chip control are priorities. For personalised application advice or to procure the SDMW09T308-A57 WKP35G from stock, contact Metav Werkzeuge for cutting data and procurement support Technical data Article number: SDMW09T308-A57-WKP35G-WALTER SKU: SDMW09T308-A57-WKP35G-WALTER Product type: Fräswendeschneidplatte Brand: Walter Tools Numbers / Core technical data Free angle: 15° Corner radius: 0.8 mm Plate form: Square 90° Plate size: 09 Plate thickness: T3 Tolerance class: M Special features / Versions Series: Tiger·tec Gold Grade: WKP35G Chipbreaker: A57 Material application: P / K (steel and cast iron) Designation without grade: SDMW09T308-A57 Execution: W FAQ What materials is this insert suitable for? The SDMW09T308-A57 WKP35G insert from Walter Tools is formulated for P / K materials, explicitly covering steel (P) and cast iron (K) applications according to ISO groupings. How does the Tiger·tec Gold coating benefit production? The Tiger·tec Gold coating on this Walter Tools insert improves wear resistance and edge robustness, helping to extend tool life and maintain consistent cutting performance over longer production runs. What does the chipbreaker A57 do for machining? The chipbreaker A57 on the SDMW09T308-A57 WKP35G promotes predictable chip breakage and evacuation, reducing swarf-related interruptions and enabling more stable cutting conditions. Is the insert suitable for finishing operations? With a 0.8 mm corner radius and a square 90° form, this insert provides geometry that can support semi-finishing and certain finishing tasks where the specified radius and tolerance class M meet the dimensional and surface requirements. Which designation should be quoted when ordering? Please refer to SDMW09T308-A57 WKP35G (SDMW09T308-A57-WKP35G-WALTER) and mention Walter Tools to ensure the correct Tiger·tec Gold grade and chipbreaker configuration are supplied. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany, info@walter-tools.com Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only. There is no affiliation between Metav Werkzeuge and the mentioned manufacturers. The offered item is original, brand-new merchandise from the manufacturer.
SDMW09T308-A57 WPP35G W - Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, a robust WPP35G carbide grade and an optimised A57 chipbreaker for dependable steel machining; order directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. SDMW09T308-A57 WPP35G milling indexable insert for steel — Walter Tools SDMW09T308-A57 WPP35G is a square milling insert engineered for productive machining of steel, offering a balanced combination of wear resistance and toughness suitable for a wide range of turning and face-milling operations. Tiger·tec Gold coated carbide grade WPP35G Optimised A57 chipbreaker for steel machining Square 90° insert with 0.8 mm nose radius 15° clearance and T3 plate thickness Greater process efficiency for steel applications The SDMW09T308-A57 WPP35G insert delivers measurable gains in process stability through its Tiger·tec Gold coating and a carbide formulation tuned for steel. The coated hardmetal composition provides a controlled wear pattern that extends tool life while maintaining cutting-edge integrity. Combined with the A57 chipbreaker, chip formation is predictable, reducing downtime from recut and improving cycle-time consistency. These technical attributes translate into fewer insert changes and a more continuous production flow, which benefits throughput and machine utilisation. Designed for consistent surface quality and flexible set-ups A square 90° geometry with a 0.8 mm nose radius gives the insert reliable edge strength and predictable surface finish in shoulder and face-milling tasks. The 15° clearance reduces rubbing and heat build-up at the flank, while the T3 thickness supports repeatable clamping stability. Together these features enable higher feed rates and a broader range of cutting parameters without sacrificing finish. For workshops seeking simple tool selection, the insert’s combination of geometry and grade delivers a straightforward choice for general steel machining where balance between life and toughness is required. Durable engagement and application guidance The WPP35G grade, part of the Tiger·tec Gold family, is formulated for balanced toughness and wear resistance when working with group P materials (steel). Its coated surface improves thermal and abrasion resistance, which is particularly beneficial in mixed-production environments or interrupted cuts. For best results, use the insert within recommended cutting parameter windows for steels and verify chip evacuation with your chosen toolholder; this will exploit the optimised A57 chip control and help maintain consistent component quality. The Walter Tools design aims to combine longevity, predictable wear and broad material coverage for everyday industrial use. Contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 to discuss Walter Tools Tiger·tec Gold inserts and find the optimal insert and parameter set for specific steel machining tasks Technical Data SKU: SDMW09T308-A57-WPP35G-WALTER Article designation: SDMW09T308-A57 WPP35G Product type: Fräswendeschneidplatte / milling indexable insert Manufacturer: Walter Tools Series: Tiger·tec Gold Facts Clearance angle: 15° Corner radius: 0.8 mm Insert form: Square 90° Size designation: 09 Plate thickness: T3 Tolerance class: M Special features Coating: Tiger·tec Gold technology Grade: WPP35G (coated carbide) Chipbreaker: A57 optimised for steel Material application: Steel (ISO group P) Execution: W FAQ What materials is this insert suitable for? The insert is designed primarily for steel (ISO group P); the WPP35G grade and A57 chipbreaker ensure effective chip control and wear behaviour when machining unalloyed and alloyed steels. Can the SDMW09T308-A57 WPP35G be used for finishing and roughing? Yes, the insert’s balanced WPP35G composition and the 0.8 mm nose radius support both finishing and moderate roughing operations in steel, provided cutting parameters are adjusted accordingly. How does the Tiger·tec Gold coating benefit machining? The Tiger·tec Gold coating enhances thermal resistance and reduces abrasive wear, which improves tool life and process stability for steel machining with the SDMW09T308-A57 insert. Is this insert compatible with standard square-milling toolholders? The insert’s square 90° form and T3 thickness match common clamping systems for indexable milling inserts; verify holder compatibility and clamping seat geometry before use. What distinguishes the A57 chipbreaker in practice? The A57 chipbreaker is tuned for steel cutting to promote short, manageable chips and predictable evacuation, reducing the risk of chip-related interruptions and improving surface quality. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product designations are mentioned for explanation only. There is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer Walter Tools.
SDMW09T320-A57 WKK25G Wendeplatten - Walter Tools
Take advantage of the combination of high process reliability, specialised WKK25G grade and optimised chip control for consistent cast iron machining; order the insert directly via Metav Werkzeuge or contact our consultants for application guidance. SDMW09T320-A57 WKK25G milling indexable insert for cast iron (Tiger‑tec Gold) – Walter Tools The SDMW09T320-A57 WKK25G is a square milling insert designed for productive machining of cast iron, delivering stable chip formation and extended tool life in interrupted and continuous milling operations. Tiger‑tec Gold coated carbide grade WKK25G Optimised for abrasive cast iron machining Square 90° insert with 2 mm corner radius 15° clearance angle for robust engagement Boosted productivity for abrasive cast iron applications The Tiger‑tec Gold series and the WKK25G grade are developed specifically for the challenges of cast iron machining. By combining a wear-resistant coating with a substrate engineered for short, brittle chips, the solution reduces flank wear and maintains cutting edge stability under high abrasive conditions. This results in predictable performance, fewer tool changes and a measurable increase in machining throughput where stable process times are essential. Consistent geometry for secure positioning and repeatability The square 90° form and a 2 mm corner radius provide a balance between strength and accessible cutting edge length. The standardised geometry ensures repeatable seating in toolholders and supports reliable indexability, which reduces setup effort and downtime. With a 15° clearance the insert tolerates moderate engagement angles while maintaining secure chip evacuation, helping to preserve surface finish and dimensional consistency on cast components. Coating technology and grade for extended tool life The Tiger‑tec Gold coating applied to the WKK25G grade enhances resistance to abrasive wear common in cast iron. The coated carbide composition improves thermal stability at the cutting zone and reduces notch wear, which extends service intervals. Improved edge integrity lowers the risk of catastrophic failure and supports longer uninterrupted production runs — a direct economic benefit in serial machining. Practical advantages in the production environment The insert’s chipbreaker A57 and tolerance class M contribute to controlled chip formation and predictable cutting forces. These attributes simplify process planning: feeds and speeds can be set with confidence, and tool performance scales well across batch and continuous operations. For milling centres and heavy-duty roughing tasks on cast iron, the combination of geometry and coating translates into fewer tool changes and a more reliable machining cycle. For application advice or to discuss the best Tiger‑tec Gold solution for specific cast iron jobs, contact Metav Werkzeuge for tailored support via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: SDMW09T320-A57-WKK25G-WALTER Designation: SDMW09T320-A57 WKK25G Manufacturer: Walter Tools Series: Tiger‑tec Gold Numbers / Core technical data Clearance angle: 15° Corner radius: 2 Plate size: 09 Plate thickness: T3 Form: Square 90° Designs / Special features Coating: Tiger‑tec Gold Grade: WKK25G Chipbreaker: A57 Tolerance class: M Material group: cast iron (K) FAQ What materials is this insert best suited for? The SDMW09T320-A57 WKK25G milling insert by Walter Tools is optimised for cast iron (material group K) and designed to handle the abrasive nature and short, brittle chips typical of these alloys. How does the Tiger‑tec Gold coating benefit tool life? Tiger‑tec Gold on the WKK25G grade improves resistance to abrasive wear and thermal loading, which extends service life and reduces the frequency of tool replacements during cast iron milling. Can this insert be used for finishing operations? The SDMW09T320-A57 WKK25G is primarily targeted at productive roughing and semi-finishing in cast iron; geometry and chip control make it suitable for stable semi-finish passes depending on machining strategy. What are the key geometry values to consider when programming a job? Important reference values include the 15° clearance angle, 2 mm corner radius and square 90° form; these influence engagement, cutter path planning and achievable surface quality. Is the insert compatible with standard Walter toolholders? The insert follows standard indexable insert dimensions and tolerance class M, enabling secure seating in compatible Walter toolholders for repeatable mounting and interchangeability. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The item offered is an original brand‑new product of the manufacturer Walter Tools.
SDMW09T320-A57 WKP35G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold coating and the WKP35G grade combined with a reliable A57 chipbreaker for steady machining of steel and cast iron; order directly via Metav Werkzeuge or consult our specialists for tailored application advice. SDMW09T320-A57 WKP35G — Milling indexable insert, Tiger·tec Gold, for steel & cast iron (Walter Tools) SDMW09T320-A57 WKP35G is a square 90° milling indexable insert with a 15° clearance angle, designed for efficient chip formation and stable cutting in steel and cast iron applications Tiger·tec Gold coating for extended tool life Square 90° insert with 2 mm corner radius 15° clearance angle for stable cutting Designed for steel and cast iron machining Consistent chip control for reliable cycle times The combination of the A57 chipbreaker and the WKP35G coated-carbide grade delivers controlled chip formation under typical cutting temperatures for steel and the abrasive nature of cast iron. The chipbreaker geometry reduces chatter and helps maintain a uniform material flow during cutting, which leads to repeatable cycle times and fewer interruptions for swarf management. This rational optimisation supports higher throughput and predictable process planning in series production. Precise geometry for reproducible surface quality A defined 15° clearance angle and a 2 mm corner radius on the square 90° insert give a stable cutting edge and low tendency to edge chipping. The geometry and tolerance class M ensure consistent seating and alignment in standard toolholders, so that each index change returns the insert to the same datum. For workshops aiming at consistent component tolerances, these features translate into reduced set-up time and less rework due to dimensional drift. Optimised for steel and cast iron according to ISO groups The grade is specified for ISO groups P (steel) and K (cast iron). This means the substrate and coating are balanced to handle the heat and ductile chip formation of steels, while simultaneously resisting the abrasive wear seen in many cast-iron cuts. For users with mixed batches of turned and milled parts, the insert provides versatile performance across the two most common engineering materials without frequent grade changes. Durable coating and economical tool life The Tiger·tec Gold coating technology applied to the WKP35G grade improves resistance to flank and crater wear, extending the useful life of the insert under medium to high cutting speeds. Longer edge life reduces tooling change frequency and contributes to lower cost per part in continuous production. The combination of coating and chipbreaker supports both roughing and semi-finishing operations where consistent edge integrity and process stability are priorities. For high-process reliability with Walter Tools’ Tiger·tec Gold WKP35G inserts, contact Metav Werkzeuge for application-specific recommendations and procurement via Metav Werkzeuge. Technical data Article number: SDMW09T320-A57-WKP35G-WALTER Designation: SDMW09T320-A57 WKP35G Product type: Milling indexable insert Series: Tiger·tec Gold Facts Clearance angle: 15° Corner radius: 2 mm Insert shape: Square 90° Insert size: 09 Thickness: T3 Tolerance class: M Special features Grade: WKP35G (coated carbide) Chipbreaker: A57 Material suitability: Steel (P), Cast iron (K) Application focus: General machining of steel and cast iron FAQ Which materials is this insert suitable for? The SDMW09T320-A57 WKP35G insert is specified for ISO groups P and K, meaning it is suitable for machining steel and cast iron as supplied by Walter Tools. What does the 2 mm corner radius affect in practice? A 2 mm corner radius increases edge strength and distributes cutting forces, improving resistance to chipping and helping to achieve stable surface finishes during milling with the SDMW09T320-A57 WKP35G insert. How does the Tiger·tec Gold coating benefit performance? The Tiger·tec Gold coating reduces abrasive and thermal wear on the cutting edge, extending tool life and maintaining cutting-edge integrity under higher speeds, which benefits productivity with the WKP35G grade. What is the role of the A57 chipbreaker? The A57 chipbreaker promotes reliable chip formation and evacuation, reducing the risk of tangling and helping to maintain consistent machining conditions when using the SDMW09T320-A57 WKP35G insert. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered article is an original, factory-new product of Walter Tools.
SDMW09T320-A57 WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and the WSP45G grade for extended tool life and reliable chip control; the square 90° geometry with a 2 mm corner radius ensures stable milling under moderate to heavy cut conditions. Order the insert directly via Metav Werkzeuge or ask our consultants if needed. SDMW09T320-A57 SDMW09T320-A57 WSP45G milling insert — Tiger‑tec Gold, for Stahl / rostfreier Stahl / Titan (Walter Tools) The SDMW09T320-A57 WSP45G is a square 90° milling insert with a 15° relief angle, designed for robust and versatile milling across Stahl, rostfreier Stahl and high‑temperature alloys such as Titan. Tiger‑tec Gold PVD coating for extended life WSP45G grade for versatile material range Square 90° format with robust 2 mm corner radius 15° relief angle for stable milling performance Longer life under heavy use for sustained productivity The combination of Tiger‑tec Gold coating and a WSP45G PVD‑coated carbide substrate delivers a clear production benefit: enhanced wear resistance and stable cutting edges under fluctuating cutting temperatures. This technological pairing reduces the frequency of index changes and minimises downtime, resulting in a measurable improvement in throughput. The coating technology supports consistent chip formation when machining a range of workpiece groups classified as P / M / S, which translates into predictable tool life and lower process variability on the shop floor. Geometry that balances strength and surface quality A square 90° format with a 2 mm corner radius and a 15° relief angle provides both rigidity and acceptable surface finish for roughing and semi‑finishing operations. The relatively large corner radius increases edge strength and resistance to chipping, while the relieved clearance angle reduces rubbing and heat build‑up at the flank. The integrated chipbreaker A57 is optimised to control swarf and reduce rework, supporting stable cutting when higher metal removal rates are required. These geometric choices deliver a straightforward compromise between load capacity and component quality. Versatile application across demanding materials The insert is tailored to ISO material groups P (Stahl), M (rostfreier Stahl) and S (high‑temperature superalloys / Titan), making it a reliable option for mixed production environments or job shops that handle diverse alloys. In practice, the grade's toughness supports interrupted cuts and variable feeds, while the PVD coating aids thermal resistance during elevated cutting temperatures. For process engineers the practical advantage is a reduced need for multiple specialised grades: one insert covers a broad spectrum of applications without frequent tool changes. For specific cutting data or optimisation, consult Metav Werkzeuge for tailored recommendations. For application advice or to secure compatible inserts and tooling from Walter Tools, contact Metav Werkzeuge for ordering and process consultation Technical data Article number: SDMW09T320-A57-WSP45G-WALTER SKU: SDMW09T320-A57-WSP45G-WALTER Type: milling insert (coated carbide) Series: Tiger‑tec Gold Grade: WSP45G ISO designation: SDMW09T320-A57 WSP45G Designation: SDMW09T320-A57 Manufacturer: Walter Tools Facts Relief angle: 15° Corner radius: 2 mm Shape: Square 90° Insert size: 09 Thickness: T3 Chipbreaker: A57 Tolerance class: M Special features Coating technology: Tiger‑tec Gold (PVD) Material compatibility: P / M / S (Stahl; rostfreier Stahl; high‑temperature alloys / Titan) Series focus: versatile PVD‑sorte for milling Intended use: roughing to semi‑finishing operations FAQ Which materials are recommended for this insert? The SDMW09T320-A57 WSP45G insert is recommended for ISO groups P (Stahl), M (rostfreier Stahl) and S (high‑temperature superalloys / Titan), offering a versatile choice for mixed workloads. What is the purpose of the A57 chipbreaker? The A57 chipbreaker on this grade supports controlled swarf formation and evacuation, improving process stability during heavier cuts with the SDMW09T320-A57 WSP45G insert. How does the corner radius affect performance? A 2 mm corner radius increases edge strength and resistance to chipping, which benefits interrupted cutting and higher feed operations while maintaining acceptable surface quality. Is this insert suitable for finishing work? Yes; while optimised for robustness and productivity, the geometry allows semi‑finishing and acceptable surface quality when appropriate feeds and speeds are selected for the SDMW09T320-A57 WSP45G. What does the Tiger‑tec Gold series bring to the application? Tiger‑tec Gold offers enhanced wear resistance and thermal stability, reducing edge degradation under fluctuating temperatures and enabling longer cutting intervals. Manufacturer: Walter Tools; part of Sandvik Coromant. AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden; support.coromant@sandvik.com Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SDMW09T3AEN-A57 WKP25S Wendeplatten - Walter Tools
Combine high productivity and predictable edge life with the Tiger·tec Silver technology and the proven chip control of the A57 design for efficient milling in steel and cast iron; order directly via Metav Werkzeuge or consult our specialists for tailored recommendations. SDMW09T3AEN-A57 WKP25S milling insert (square 90°, 15° clearance) – Walter Tools The SDMW09T3AEN-A57 WKP25S is a coated carbide milling insert designed for medium to heavy machining of steel and cast iron, offering a robust chipformer and consistent edge stability for productive milling operations. Tiger·tec Silver coated carbide technology Optimised chipformer A57 for stable chips Square 90° design, 15° clearance angle For machining steel (P) and cast iron (K) Higher throughput for steel and cast-iron applications The insert delivers a measurable improvement in cycle efficiency by combining the WKP25S grade with the Tiger·tec Silver coating, which is engineered for common steel and cast-iron machining conditions. The grade is tailored to the heat and chip behaviour typical for group P (steel) and group K (cast iron), so the component life is extended and downtime is reduced. This results in a clear economic benefit: fewer index changes, less spindle idle time and a steadier production flow. The specification of the tool is optimised to support repeated, consistent results in series production. Durable coating for extended edge life and economy A coated carbide substrate with an advanced surface finish provides wear resistance that delays flank and crater wear under standard cutting conditions. The coated carbide construction and the Tiger·tec Silver treatment reduce abrasive wear and improve thermal stability; this converts into longer service intervals and lower tool consumption. For engineers and buyers the benefit is straightforward: improved process stability and a reduced cost per component through longer insert life and predictable regrinding or replacement intervals. Predictable chip control and dependable geometry The combination of a square 90° profile, 15° clearance angle and the chipformer A57 yields controlled, compact chips and a stable cutting load. The chipformer acts to break and direct chips reliably so that evacuation is improved and the risk of chip-related rework is lowered. For operations where component surface quality and process repeatability matter, this geometry minimises vibration and supports a consistent cut. The tolerance class M ensures repeatable seating and minimal deviation between insert changes, which is crucial when cycle-to-cycle consistency is required. Easy integration and clear specification for set-up With a nominal thickness T3 and plate size 09, the insert fits standard toolholders specified for this ISO designation and is identified by the concise marking SDMW09T3AEN-A57 WKP25S. The execution code W and the square format simplify tool mounting and inventory management in a workshop environment. Because the product data specifies suitability for steel (P) and cast iron (K), tool selection for mixed-production lines becomes easier and changeovers are reduced. The precise geometry and clear grade assignment support predictable machining parameters, enabling planning for throughput and maintenance intervals. Contact Metav Werkzeuge for a quotation or to discuss how Walter Tools’ SDMW09T3AEN-A57 WKP25S inserts can be integrated into existing milling processes Technical data Article number: SDMW09T3AEN-A57-WKP25S-WALTER Designation: SDMW09T3AEN-A57 WKP25S Manufacturer: Walter Tools Core data Clearance angle: 15° Plate form: Square 90° Plate size: 09 Thickness: T3 Tolerance class: M Materials & special features Series / coating: Tiger·tec Silver Grade: WKP25S Chipformer: A57 Suitable for: Steel (P), Cast iron (K) Execution: W FAQ What materials is this insert suitable for? The SDMW09T3AEN-A57 WKP25S insert is designed for machining steel (P) and cast iron (K) in accordance with its grade and the Tiger·tec Silver coating characteristics. Which chip control behaviour can be expected with the A57 geometry? The A57 chipformer produces compact, broken chips and directs them away from the cutting zone, which improves evacuation and reduces the likelihood of re-cutting or part damage during milling. How does the Tiger·tec Silver coating influence tool life? The Tiger·tec Silver coating enhances thermal resistance and reduces abrasive wear on the coated carbide substrate, leading to longer edge life and more consistent component quality. Is the insert suitable for automated tool-change systems? Yes; the ISO designation, square 90° format and tolerance class M support repeatable seating and reliable indexing in automated tool-change systems. What should be considered when replacing an existing insert with this grade? When switching to the SDMW09T3AEN-A57 WKP25S, check holder compatibility for a T3 thickness and verify that machining parameters are adapted to the grade’s heat and chip behaviour for steel and cast iron. Manufacturer: Walter Tools / Responsible: AB Sandvik Coromant; Mossvägen 10; 811 34 Sandviken; Sweden; support.coromant@sandvik.com Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are stated for clarification only and do not imply any connection between our company and the named brands. The offered item is original new production from the manufacturer.
SDMW09T3AEN-A57 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating, the WKP35S grade and stable A57 chip control for reliable machining of steel and cast iron; order directly via Metav Werkzeuge or contact their consultants for tailored cutting data. SDMW09T3AEN-A57 WKP35S milling indexable insert — Tiger‑tec Silver for steel and cast iron (Walter Tools) The SDMW09T3AEN-A57 WKP35S is a square 90° milling insert with a 15° clearance angle, designed for productive machining of unalloyed and alloyed steels as well as cast iron applications. Tiger‑tec Silver coating for high process security Grade WKP35S — coated carbide for steel and cast iron Square 90° form with 15° clearance angle T3 thickness with A57 chipbreaker for stable chip control Consistent chip control for efficient steel and cast‑iron machining The combination of the WKP35S grade and the Tiger‑tec Silver series delivers a coating and substrate pairing engineered for chip formation in ISO groups P and K. The A57 chipbreaker is shaped to produce short, controllable chips when machining steel and cast iron, reducing the risk of built‑up edge and improving process stability. For workshops that require predictable tool behaviour, this insert offers repeatable chip breakage and less interruption for chip clearance, which supports higher effective cutting times and smoother tool exchanges. Geometry engineered for surface quality and repeatability A square 90° form with a 15° clearance angle and T3 thickness yields a robust cutting edge that resists deformation under intermittent and continuous cuts. The indexable design permits four usable edges per insert, improving economy per edge change while the tolerance class M ensures consistent seating in the tool holder. These geometric characteristics translate into better surface finishes and dimensional repeatability on the workpiece, particularly in general purpose milling operations and shoulder cuts where edge life and stability matter. Coating and substrate benefits that cut operating costs The coated carbide construction, typical of the Tiger‑tec Silver family, provides abrasion resistance and thermal stability during elevated cutting speeds. This leads to extended tool life, fewer insert changes and reduced downtime—advantages that convert directly into lower cost per part in production cycles. The insert’s suitability for both alloyed and unalloyed steels and for cast iron makes it a versatile choice for mixed‑material batches, enabling fewer tool variants on the shop floor and a leaner tooling inventory. Practical application guidance and selection tips This insert is suitable for a wide range of milling tasks from roughing to light finishing when matched with appropriate cutting data and tool holders. The A57 chipbreaker assists with short chips typical for cast materials, while the coating and grade combination is optimised for heat management in steel machining. For selection, pair the square 90° insert with a rigid holder and moderate depths of cut to exploit the insert’s stability; adjust feed and speed based on material group (ISO P/K) and machine capability. For customised recommendations or cutting parameters, technical advisors at Metav Werkzeuge can provide documented guidance and published starting values. Contact Metav Werkzeuge to discuss Walter Tools Tiger‑tec Silver inserts, request specific cutting data for the SDMW09T3AEN-A57 WKP35S or arrange supply and logistics support Technical data Article number: SDMW09T3AEN-A57-WKP35S-WALTER Designation: SDMW09T3AEN-A57 WKP35S Manufacturer: Walter Tools Product type: Milling indexable insert Series: Tiger‑tec Silver Facts Clearance angle: 15° Plate form: Square 90° Plate size: 09 Plate thickness: T3 Chipbreaker: A57 Tolerance class: M Special features Grade: WKP35S Coated carbide (Tiger‑tec Silver technology) Material suitability: Steel (P), Cast iron (K) Stable chip control for short, broken chips Indexable insert with four cutting edges FAQ What materials is this insert designed to machine? The SDMW09T3AEN-A57 WKP35S insert is designed for steel (ISO group P) and cast iron (ISO group K), exploiting the WKP35S grade and Tiger‑tec Silver coating for those materials. How does the A57 chipbreaker affect machining? The A57 chipbreaker produces short, controllable chips that improve swarf evacuation and reduce the likelihood of chip entanglement, particularly beneficial when machining cast iron and interrupted cuts with this Walter Tools milling insert. Can this insert be used for finishing passes? Yes; with appropriate cutting parameters and a rigid tool holder the insert can be used for light finishing as well as for productive roughing operations. How many edges are usable per insert and what tolerance class applies? The square form provides four usable cutting edges per insert and the tolerance class is M, ensuring consistent fit and repeatability in the tool holder. Is specialised coolant required when using this insert? No specialised coolant is mandatory; coolant strategy should be selected based on material and machine capability. For guidance on coolant and speeds/feeds, refer to the technical data provided with the SDMW09T3AEN-A57 WKP35S or consult Metav Werkzeuge. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners and are mentioned for clarification purposes only. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer.
SDMW09T3AZN-A57 WAK15 Wendeplatten - Walter Tools
Take advantage of the combination of sharp geometry, a carbide grade tailored for non‑ferrous metals and reliable chip control to improve throughput in aluminium machining; order the insert directly via Metav Werkzeuge or contact the consultants for technical advice. SDMW09T3AZN-A57 WAK15 milling indexable insert for aluminium and non‑ferrous metals — Walter Tools SDMW09T3AZN-A57 WAK15 is a square 90° milling insert designed for efficient, high‑quality machining of aluminium and other non‑ferrous materials, offering secure seating and predictable chip formation. Grade WAK15 for aluminium machining Square 90° geometry for stable seating 15° clearance angle for light cutting engagement Chipbreaker A57 for secure chip control Consistent performance for aluminium applications The WAK15 carbide grade is an uncoated carbide formulation optimised for machining aluminium and other non‑ferrous metals. Combined with the insert's sharp edge geometry and the integrated chipbreaker A57, the system reduces the risk of built‑up edge and material adhesion, which translates into fewer interruptions and more consistent cycle times. For production environments where repeatability matters, this configuration supports dependable part quality and improved surface finish. Design features that support stability and accuracy The square 90° form and 15° clearance angle deliver predictable engagement and straightforward seat orientation in standard milling clamping systems. The compact T3 thickness offers a balance between rigidity and light engagement, making the insert suitable for both finishing and medium‑feed operations in aluminium alloys. The combination of geometry and tolerance class M helps maintain repeatable tool life and contributes to predictable machining behaviour in automated processes. Practical benefits explained for procurement and shopfloor teams The insert belongs to the Walter N‑grade system, a series focused on non‑ferrous machining. Using uncoated carbide eliminates coating transfer risks on soft metals while preserving cutting edge sharpness; this is particularly useful when working with sticky or highly ductile aluminium grades. The chipbreaker A57 directs and breaks chips to avoid tangling and to keep coolant and evacuation paths clear, aiding both manual and high‑speed automated setups. How the insert supports productivity and process security With its targeted material focus and defined geometry, this insert reduces secondary operations caused by poor chip control and minimizes rework driven by surface blemishes. The engineered combination of grade, form and chip control enhances productivity through longer effective tool life per insert and fewer stoppages for tool changes. For manufacturing lines handling mixed non‑ferrous batches, the consistent behaviour of this insert simplifies tool management and process planning. Contact Metav Werkzeuge for tailored tooling recommendations and rapid availability of Walter Tools inserts — eMail: info@metav-werkzeuge.com or phone +49 2822 7131930 Technical Data Article number: SDMW09T3AZN-A57-WAK15-WALTER Designation: SDMW09T3AZN-A57 WAK15 Series: Walter N-Sortensystem Grade: WAK15 Manufacturer: Walter Tools Facts Insert size: 09 Thickness: T3 Clearance angle: 15° Form: Square 90° Tolerance class: M Special features Chipbreaker: A57 Uncoated carbide (Walter WAK15) For aluminium and non‑ferrous metals Walter N‑grade system FAQ Which materials is this insert intended for? The SDMW09T3AZN-A57 WAK15 insert is intended primarily for aluminium and other non‑ferrous metals, as defined by the Walter WAK15 grade and the Walter N‑grade system. Is the insert coated or uncoated? The insert is an uncoated carbide grade (WAK15), chosen to maintain a sharp cutting edge and to avoid coating transfer when machining soft or adhesive materials. What advantage does the chipbreaker A57 provide? The chipbreaker A57 controls chip form and promotes short, manageable chips during cutting, reducing chip entanglement and improving evacuation in both manual and automated milling operations. How does the square 90° geometry affect machining? The square 90° form offers stable seating and equal cutting edge usage around the insert perimeter, supporting straightforward indexation and balanced load distribution during milling. How significant is the 15° clearance angle for performance? A 15° clearance angle provides a light radial engagement that helps maintain a sharp effective cutting edge and reduces rubbing on the workpiece, which is advantageous when finishing or working with delicate aluminium alloys. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanation. There is no affiliation between Metav Werkzeuge and the mentioned brands. The offered item is an original, factory‑new product from the manufacturer.
SDMW09T3AZN-A57 WKP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the WKP35G grade for reliable performance in steel and cast iron milling; the square 90° geometry with 15° clearance delivers predictable chip control and consistent component quality. Order the SDMW09T3AZN-A57 WKP35G directly via Metav Werkzeuge or consult the team for application-specific advice. SDMW09T3AZN-A57 WKP35G – Walter Tools indexable milling insert, Tiger·tec Gold coated for steel and cast iron A SDMW09T3AZN-A57 WKP35G indexable milling insert designed for precision face and shoulder milling in steel and cast iron, combining a coated carbide grade with a stable chipbreaker geometry for productive machining. Tiger·tec Gold coated grade WKP35G Optimised chipbreaker A57 for stable chips Square 90° form, 15° clearance angle Suited for steel and cast iron machining High productivity for steel and cast iron components The WKP35G grade, part of Walter Tools’ Tiger·tec Gold family, is a coated carbide solution optimised for the thermal and mechanical demands of machining steel (P) and cast iron (K). The coating improves wear resistance under interrupted cuts and mixed cutting conditions, which supports longer tool life and fewer tool changes. For production environments where consistent cycle times are essential, this insert provides a predictable performance profile that helps maintain throughput. Geometry that delivers repeatable quality A square 90° insert geometry coupled with a 15° clearance angle and the chipbreaker A57 produces short, controllable chips and a stable cutting process. The moderate rake and relief combine to reduce cutting forces on heavy shoulders and permit reliable indexing in standard cutter bodies. In addition, the T3 plate thickness and tolerance class M ensure accurate seating and interchangeability in toolholders, minimising setup variation and preserving surface quality across batches. Robust coating and material pairing for process security The combination of Tiger·tec Gold technology and the WKP35G micrograin carbide matrix targets abrasive wear and flank-loading typical for cast parts and structural steels. The result is improved edge stability and retained cutting geometry over longer contact lengths, increasing mean time between tool changes and supporting higher average metal removal rates. This translates into measurable gains in productivity and reduced downtime for regrinding or insert replacement. Practical integration into milling tool lines Execution marked as W and the ISO designation SDMW09T3AZN-A57 provide clear indexing and geometry references for toolroom planners and purchasers. The insert’s consistent dimensions and chip control mean fewer corrective passes and reduced post-process finishing in many applications. For operational planning, the grade’s broad material coverage simplifies inventory by covering both steel and cast iron jobs with a single insert family. For tailored application advice on Walter Tools Tiger·tec Gold inserts and availability, contact Metav Werkzeuge for expert recommendations and order coordination at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: SDMW09T3AZN-A57-WKP35G-WALTER Product: milling insert (Fräswendeschneidplatte) Brand: Walter Tools Series: Tiger-tec Gold Core data Free angle: 15° Plate form: square 90° Plate size: 09 Plate thickness: T3 Chipbreaker: A57 Tolerance class: M Special features Grade: WKP35G Coating: Tiger·tec Gold (coated carbide) Suitable for: steel (P) and cast iron (K) Execution: W ISO designation: SDMW09T3AZN-A57 WKP35G FAQ Which materials are recommended for this insert? The SDMW09T3AZN-A57 WKP35G insert is intended for steel (P) and cast iron (K) applications and is optimised for the typical thermal and chip characteristics of these material groups. What makes the WKP35G grade different from standard grades? WKP35G is a Walter Tools coated carbide grade within the Tiger·tec Gold technology, designed to combine wear resistance with stable edge retention, supporting productive machining across a range of steels and cast irons. How does the chipbreaker A57 influence machining? The chipbreaker A57 promotes short, controlled chips and consistent chip flow, which reduces the risk of chip entanglement and helps maintain a stable cutting process on interrupted or varying-depth cuts. Is the insert suitable for indexable milling heads with square seats? Yes, the square 90° form and tolerance class M ensure accurate seating and repeatable positioning in compatible milling toolholders designed for square inserts. Can the insert be used for finishing operations? Depending on the cutter geometry and cutting parameters, the insert’s coating and edge stability can deliver acceptable surface finishes; however, final surface requirements may still call for dedicated finishing grades or toolpaths. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand: Walter Tools) with headquarters in Tübingen is among the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names belong to their respective owners. Brand names are mentioned for explanation only. There is no connection between our company and the named brands. The offered item is original factory-new goods of the manufacturer.
SDMW09T3AZN-A57 WPP35G W - Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold wear resistance, consistent chip control and a compact T3 thickness for reliable steel machining; order the SDMW09T3AZN-A57 WPP35G insert via Metav Werkzeuge or consult the team for tailored application advice and rapid delivery. SDMW09T3AZN-A57 WPP35G — milling insert for steel machining by Walter Tools The SDMW09T3AZN-A57 WPP35G is a coated carbide milling insert engineered for efficient machining of steel (ISO P) in general milling applications, offering stable cutting and reproducible results. Tiger·tec Gold coating for long tool life Optimised chip control with A57 breaker Square 90° geometry for versatile milling 15° clearance angle for secure engagement Boosted productivity through advanced coating and grade The combination of the Tiger·tec Gold coating and the WPP35G grade delivers improved wear resistance and thermal stability, which translates into longer intervals between tool changes and fewer interruptions to production. As a coated carbide solution, this insert is tailored to the thermal and chip-formation conditions typical when machining steel (ISO P); the result is consistent cutting performance and reduced scrap rates. The engineered coating stack also helps maintain a stable cutting edge under varied cutting speeds, supporting a more predictable machining cycle time. Reliable chip control and geometry for smoother operation The chipbreaker A57 and square 90° form offer controlled chip evacuation and versatile entry angles, lowering the risk of built-up edge and improving surface finish. With a 15° clearance angle the insert engages the workpiece with stability, reducing chatter in interrupted cuts and allowing reliable pocketing and shoulder milling. These geometry choices make the insert particularly effective where repeatable dimensional accuracy and good surface quality are required, simplifying process planning and fixturing. Practical advantages in handling and application The compact T3 thickness and standard tolerance class M support predictable seating and clamping in common toolholders, aiding quick insert changes and secure fixture mounting. The designation aligns with established indexable insert interfaces, so integration into existing tool systems is straightforward. Given its focus on steel machining, the grade offers a balanced combination of wear resistance and toughness for a broad range of unalloyed and alloyed steels, helping to maintain steady productivity across mixed part runs. For specialised selection guidance or application-specific recommendations on the Tiger·tec Gold WPP35G grade, contact Metav Werkzeuge for expert consultation and quick availability by e‑mail or phone: info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: SDMW09T3AZN-A57-WPP35G-WALTER Article designation: SDMW09T3AZN-A57 Grade: WPP35G Series: Tiger-tec Gold Facts Geometry: Square 90° Free clearance angle: 15° Thickness: T3 Chipbreaker: A57 Tolerance class: M Special features Coating: Tiger·tec Gold (coated carbide technology) Material suitability: Steel (ISO P) Execution: W Product type: Milling indexable insert Manufacturer: Walter Tools FAQ What materials is this insert suitable for? The insert is specified for machining steel (ISO P); the WPP35G grade is optimised for unalloyed and alloyed steels with typical heat and chip-formation behaviour. How does the Tiger·tec Gold coating affect tool life? The Tiger·tec Gold coating on the SDMW09T3AZN-A57 WPP35G increases wear resistance and thermal stability, which generally extends tool life and reduces the frequency of insert changes in steel machining. Which chipbreaker is included and what benefit does it provide? The A57 chipbreaker provides controlled chip formation and evacuation, improving surface finish and reducing the risk of built-up edge during milling. Is this insert compatible with standard indexable milling holders? Yes, the square 90° form and T3 thickness conform to common insert interfaces, enabling straightforward integration into standard milling toolholders. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SDMW120408-A57 WKP25S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, proven WKP25S grade and precise square geometry for reliable milling of steel and cast iron; request ordering details or technical advice via Metav Werkzeuge to integrate this insert into existing tool systems. SDMW120408-A57 WKP25S milling insert (square 90°, for steel & cast iron) — Walter Tools A high-performance milling insert, the SDMW120408-A57 WKP25S is designed for efficient roughing and finishing operations in steel and cast iron where predictable wear behaviour and stable chip formation are required. Tiger·tec Silver coating for superior wear resistance Grade WKP25S for steel and cast iron machining Square 90° form with 0.8 mm corner radius A57 chipbreaker and 15° clearance angle Maximise tool life with advanced coated carbide technology The Tiger·tec Silver coating combined with the WKP25S carbide grade delivers improved resistance to abrasive wear and thermal loading during continuous milling. This technological pairing reduces flank wear rates and extends effective lifetime, which translates into fewer tool changes and lower process interruptions. For mixed-production runs where both long tool life and consistent performance matter, the coated carbide composition supports predictable maintenance intervals and process planning. Stable chip control and consistent cutting performance The A57 chipbreaker geometry and the square 90° form ensure reliable chip segmentation when machining both steel and cast iron. A clearance angle of 15° and a corner radius of 0.8 mm balance strength at the cutting edge with favourable cutting forces, reducing vibration and improving cutter stability. These features contribute directly to consistent surface finish and repeatable dimensional results, especially in demanding interrupted cuts and variable stock conditions. Productivity gains through geometry and grade selection The combination of the insert’s geometry and the WKP25S grade is oriented towards process security and productivity. The insert supports efficient material removal rates while maintaining edge integrity under typical steel and cast iron cutting regimes according to ISO classifications. For production environments aiming to increase throughput without sacrificing component quality, this insert offers an economical compromise between cutting speed, tool life and surface quality. Contact Metav Werkzeuge for personalised recommendations and procurement of Walter Tools Tiger·tec Silver inserts, including application matching and delivery options Technical data Article number: SDMW120408-A57-WKP25S-WALTER Product designation: SDMW120408-A57 WKP25S Product type: Milling insert (square 90°) Manufacturer: Walter Tools Series: Tiger-tec Silver Grade: WKP25S Execution: W Chipbreaker: A57 Tolerance class: M Facts Clearance angle: 15° Corner radius: 0.8 mm Plate size: 12 Plate thickness: 04 Material groups: P / K Special features Coating: Tiger·tec Silver Substrate: Coated carbide Main applications: Steel, Cast iron Geometry: Square, 90° Intended use: Milling operations FAQ What materials is this insert suitable for? The SDMW120408-A57 WKP25S insert in the Walter Tools Tiger·tec Silver series is suitable for machining steel (P) and cast iron (K) in accordance with the grade’s ISO material coverage. How does the chipbreaker affect performance? The A57 chipbreaker on this Walter Tools milling insert promotes controlled chip formation during milling, improving evacuation and reducing the risk of built-up edge when working with steel and cast iron. What benefit does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating on the WKP25S grade enhances wear resistance and thermal stability, leading to longer tool life and more consistent machining results under typical production loads. Is the insert geometry suited to interrupted cuts? Yes. The square 90° form, 15° clearance and 0.8 mm corner radius combine to offer edge robustness and vibration damping, making this insert appropriate for interrupted and continuous milling tasks. Which SKU should be quoted when ordering? Use SKU SDMW120408-A57-WKP25S-WALTER to specify this exact Walter Tools milling insert and ensure correct series, grade and geometry are delivered. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (marketed as Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and trade names remain the property of their respective owners. Brand names are used for explanation only; there is no affiliation implied between our company and the named manufacturers. The offered article is an original, factory-new product of the manufacturer.
SDMW120408-A57 WPP35G W - Wendeplatten - Walter Tools
Take advantage of the combination of the Tiger·tec Gold coating, WPP35G grade and a defined square 90° geometry for consistent, productive milling of steel components; order via Metav Werkzeuge or consult the team for application advice. SDMW120408-A57 WPP35G milling indexable insert, square 90°, 0.8 mm corner radius — Walter Tools A SDMW120408-A57 WPP35G is a coated carbide indexable insert engineered for reliable milling of steel, featuring the Tiger·tec Gold coating and an A57 chipbreaker for stable chip formation Tiger·tec Gold coated carbide Optimised chip control A57 Square 90° geometry, 0.8 mm radius Designed for steel machining Greater throughput when machining steel The combination of the Tiger·tec Gold coating and a WPP35G coated carbide substrate delivers a clear performance advantage when milling steel. The coating reduces flank wear and improves thermal stability, which translates into longer edge life and fewer index changes during production. For industrial shops that prioritise process continuity, this results in higher machine uptime and more consistent component quality. The grade is tuned for the typical heat and chip characteristics of steel machining, helping to maintain cutting conditions across a range of feeds and speeds. Predictable chip control and consistent surface finish The A57 chipbreaker, paired with the square insert geometry, produces short, controlled chips in interrupted and continuous cuts. The square 90° form and 0.8 mm corner radius provide a robust cutting edge that supports reliable entry and exit behaviour, particularly in shoulder milling and face operations. This controlled chip formation reduces the risk of built-up edge and supports a stable cutting process, which helps to achieve repeatable surface finishes and dimensional stability without frequent operator intervention. Process security and tool-system compatibility Tolerance class M and the SDMW-style designation ensure consistent fit and repeatability in compatible toolholders. As a standardised indexable insert, it integrates into established milling systems and is suitable for automated tool-change environments. The insert’s specification emphasises broad applicability for steel machining in general production, offering a balance between wear resistance and toughness that suits mixed-batch shops and series production alike. Walter Tools’ engineering focus on process security supports predictable tool life and easier process planning. For tailored advice on application parameters and holder compatibility for Walter Tools inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for prompt technical support and ordering guidance. Technical data SKU: SDMW120408-A57-WPP35G-WALTER Designation: SDMW120408-A57 WPP35G Series: Tiger-tec Gold Grade: WPP35G Facts Plate form: Square 90° Free cutting angle: 15° Corner radius: 0.8 mm Plate size code: 12 Thickness code: 04 Tolerance class: M Special features Coating: Tiger·tec Gold Chipbreaker: A57 Material application: Steel (P) Execution: W Series description: Coated carbide grade for steel machining FAQ Which materials is this insert intended for? The SDMW120408-A57 WPP35G insert is designed primarily for steel (P) applications; the WPP35G grade is optimised for the heat and chip characteristics of steel machining. What advantages does the Tiger·tec Gold coating provide? Tiger·tec Gold on the WPP35G grade increases thermal stability and wear resistance, which improves edge life and process reliability for the SDMW120408-A57 insert. What does the A57 chipbreaker achieve in practice? The A57 chipbreaker supports short, controlled chips and stable cutting forces, aiding predictable surface finish and reduced risk of built-up edge when using the SDMW120408-A57 insert. Is the square geometry suitable for shoulder milling? Yes— the square 90° form with a 0.8 mm corner radius is well suited to shoulder and face milling tasks that require robust edge strength and repeatable corner performance. How does tolerance class M affect installation? Tolerance class M ensures consistent dimensional accuracy for the insert, aiding repeatable seating and predictable performance in compatible toolholders. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com