SDMT120408-F57 WSM35G WSM35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the robust WSM35G grade to increase process security when machining stainless steels and heat‑resistant alloys; order this insert directly via Metav Werkzeuge or ask the consultants for application advice. SDMT120408-F57 WSM35G milling indexable insert – Tiger·tec Gold, Walter Tools The SDMT120408-F57 WSM35G is a square 90° milling insert engineered for heavy‑duty machining of stainless steels and superalloys, offering stable edge life and reliable chip control. Tiger·tec Gold coated carbide grade WSM35G Designed for stainless steels and superalloys Square 90° insert with 0.8 mm corner radius 15° relief angle and F57 chipbreaker geometry Increase uptime through thermal and edge stability The combination of the Tiger·tec Gold coating and the WSM35G substrate delivers improved thermal resistance and a tougher cutting edge compared with standard grades. This results in more predictable wear behaviour when machining demanding materials classified as M (rostfreie Stähle) and S (heat‑resistant superalloys and titanium) under ISO 513. The specifically developed coating reduces adhesion and built‑up edge, which extends the usable life of the tool and reduces unplanned tool changes—direct benefits for cycle time and overall equipment effectiveness. Reliable chip control for consistent surface quality With its F57 chipbreaker geometry and a 0.8 mm corner radius, the insert produces controlled chip formation even under the adverse cutting conditions typical of stainless and high‑temperature alloys. The square 90° format provides a stable cutting shoulder and predictable engagement, supporting consistent surface finish and dimensional control across repetitive passes. In practical terms, this means fewer rejects and lower rework rates when tight tolerances and finish requirements are critical. Stable cutting performance with clear process benefits The 15° relief angle and the insert’s robust construction contribute to a stable cutting edge that resists chipping and thermal softening. This stability supports higher feed rates where the machine and fixture allow, translating into improved productivity without sacrificing component quality. The overall package emphasises process security and repeatability—key considerations for production environments where predictable tool life and part output are valued above short‑term cost savings. Application guidance and machining recommendations For roughing and medium finisher passes in stainless steels and superalloys, choose cutting parameters that balance tool life and material removal rate; the WSM35G grade is optimised for such situations. Use positive cutting depths and maintain coolant or suitable cutting fluid strategies to aid heat dissipation and chip evacuation. If further parameter optimisation is required for a specific alloy or geometry, Metav Werkzeuge can provide application support and test data to refine feeds and speeds. Contact Metav Werkzeuge for tailored application advice or to request availability of Walter Tools Tiger·tec Gold inserts; their consultants can advise on the best insert grade and cutting data for specific materials and machine capacities. Technical data Article number: SDMT120408-F57-WSM35G-WALTER Designation: SDMT120408-F57 WSM35G Manufacturer: Walter Tools Series: Tiger‑tec Gold Core specifications Relief angle: 15° Corner radius: 0.8 mm Plate form: Square 90° Plate size: 12 Thickness: 04 Tolerance class: M Materials & special features Grade: WSM35G (coated carbide) Coating technology: Tiger·tec Gold Chipbreaker: F57 Application groups: M (stainless steels), S (superalloys / titanium) Execution: T Brand: Walter Tools FAQ What materials is this insert best suited for? The SDMT120408-F57 WSM35G insert is designed primarily for stainless steels (ISO group M) and for heat‑resistant superalloys and titanium (ISO group S), where thermal resistance and edge stability are required. How does the F57 chipbreaker affect machining? The F57 chipbreaker optimises chip formation for interrupted and continuous cuts in tough materials, improving evacuation and reducing the risk of built‑up edge when using the SDMT120408-F57 WSM35G insert. What are the geometric specifics I should expect? Expect a square 90° insert with a 0.8 mm corner radius and a 15° relief angle, providing a stable cutting shoulder and predictable dimensional results with the SDMT120408-F57 WSM35G. Can this insert be used for finishing operations? Yes; depending on the workpiece alloy and machine stability, the SDMT120408-F57 WSM35G can be used for medium finishing where its coating and geometry help maintain surface quality. Is this a coated or uncoated grade? This is a coated carbide grade utilising Tiger·tec Gold technology to enhance thermal resistance and reduce adhesion in demanding applications such as stainless steels and superalloys. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SDMT120408-F57 WSM45X WSM45X Wendeplatten - Walter Tools
Take advantage of the WSM45X coated carbide grade with chipbreaker F57 and a 0.8 mm corner radius for consistent chip control and extended edge life when machining stainless steel and heat‑resistant superalloys; order the SDMT120408‑F57 WSM45X insert directly via Metav Werkzeuge or request application advice from our consultants. Indexable milling insert SDMT120408‑F57 WSM45X — Walter Tools (square 90°, 15° relief) SDMT120408‑F57 WSM45X is a robust indexable milling insert designed for demanding stainless steel and superalloy applications Walter WSM45X coated carbide grade Chipbreaker F57 for controlled chip formation 15° relief and 0.8 mm corner radius Square 90° insert, size 12 mm High performance grade for demanding materials The WSM45X cutting grade is a coated carbide formulation optimised for machining stainless steel (ISO M) and heat‑resistant superalloys (ISO S). Its composition supports stable chip formation and improved wear resistance under elevated cutting temperatures, which translates into longer tool life and fewer index changes. For operations where material adhesion, work hardening and heat generation are critical factors, the grade provides a balance between edge stability and thermal tolerance to maintain productive cutting cycles. Geometry that secures edge life and chip control The insert’s geometry combines a 15° relief with a 0.8 mm corner radius and a dedicated chipbreaker F57, delivering reliable chip evacuation and reinforced cutting edges. The square 90° form offers four usable cutting edges, enabling economic indexation and consistent repeatability on each corner. These geometric choices reduce the risk of built‑up edge and flank wear during interrupted cuts or heavy cross‑section engagement, supporting steady surface quality and reduced rework rates. Production benefits: process security and efficiency Designed for industrial milling applications, the insert promotes process security by maintaining a predictable cutting behaviour in tough materials specified by ISO 513. The combination of grade and chipbreaker reduces cycle variability and can improve overall throughput by lowering the frequency of tool changes. In practice, this means fewer stoppages and a more consistent output, which contributes to improved machine utilisation and a steadier cost per component over longer production runs. Compatibility, handling and application notes The SDMT geometry is compatible with standard SDMT insert holders and is supplied in execution code T with tolerance class M and thickness code 04. The insert is especially suitable where reliable cutting performance in stainless steel and titanium or Ni‑based alloys is required. For specific cutter body pairing, feed and speed windows, or when transitioning from alternative grades, consult the tooling documentation or Metav Werkzeuge’s technical advisers to match holder geometry, cutting data and coolant strategy to the component material and machining task. For procurement and tailored application support for the Walter Tools SDMT120408‑F57 WSM45X insert, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for prompt assistance and availability information. Technical Data Article number: SDMT120408‑F57‑WSM45X‑WALTER Name: Indexable milling insert SDMT120408‑F57 WSM45X Manufacturer: Walter Tools Product type: Indexable milling insert Execution: T Facts Relief angle: 15° Corner radius: 0.8 mm Plate form: Square 90° Plate size: 12 mm Thickness code: 04 Tolerance class: M Special features Grade: WSM45X (coated carbide) Chipbreaker: F57 Series: Walter Schneidstoffsorte − Serie offen Material suitability: stainless steel (ISO M), heat‑resistant superalloys/titanium (ISO S) Stable chip formation and edge durability FAQ What materials is this insert designed to machine? The SDMT120408‑F57 WSM45X insert by Walter Tools is specified primarily for stainless steel (ISO M) and heat‑resistant superalloys/titanium (ISO S) as indicated by the grade composition and chipbreaker geometry. How does the chipbreaker F57 affect performance? Chipbreaker F57 provides controlled chip formation and evacuation; combined with the WSM45X grade it improves edge stability and reduces the risk of built‑up edge during machining of tough alloys. Which cutting geometries contribute to surface quality? The combination of a 15° relief, 0.8 mm corner radius and the square 90° form helps maintain a stable cutting edge and consistent surface finish while offering four indexable corners for cost efficiency. Is the insert suitable for finishing and semi‑finishing operations? Yes, the coated carbide grade and the insert geometry are appropriate for finishing and semi‑finishing in demanding materials, with the final choice depending on machine setup and cutting parameters. How should the insert be referenced when ordering? Reference the SKU SDMT120408‑F57‑WSM45X‑WALTER or the designation SDMT120408‑F57 WSM45X when ordering to ensure correct grade, chipbreaker and geometry. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. Brand names and trademarks are mentioned for explanation only. There is no connection between our company and the mentioned brands. The offered article is original factory‑new merchandise of the manufacturer.
SDMT120408-F57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Gold coating and the versatile WSP45G grade to secure stable cutting edges and consistent chip control across steel, stainless and high‑temperature alloys; order directly via Metav Werkzeuge or consult the team for process recommendations. SDMT120408-F57 WSP45G milling indexable insert — Walter Tools, Tiger‑tec Gold, chipbreaker F57 The SDMT120408-F57 WSP45G is a square milling insert designed for versatile milling of steels, stainless steels and heat‑resistant superalloys, combining a PVD‑coated carbide grade with an F57 chipbreaker for controlled machining. SDMT120408-F57 WSP45G by Walter Tools Tiger‑tec Gold PVD coating for edge stability Versatile for steel, stainless and superalloys Square 90° form with 0.8 mm corner radius Consistent performance across mixed workpiece groups The combination of the WSP45G grade and the Tiger‑tec Gold coating delivers a balance of toughness and wear resistance suited to mixed‑material production. The insert’s PVD‑coated carbide substrate supports secure chip formation and reduced flank wear when machining group P (steel), M (rostfreiem Stahl) and S (superalloys/titanium) materials. This results in fewer unplanned tool changes and more predictable cycle times on machines running varied batches, improving throughput without sacrificing surface quality or edge life. Geometry and chip control that make a measurable difference The insert features a dedicated chipbreaker F57 and a positive clearance geometry with a 15° relief that together promote stable cutting and effective chip evacuation. The square 90° form and 0.8 mm corner radius ensure a robust cutting edge for both light finishing and moderate intermittent cuts; the square shape also provides multiple indices for economical re‑indexing. Explaining the chipbreaker: the pocketed F57 geometry breaks chips into manageable lengths, lowering the risk of recutting and supporting higher metal removal rates with steady surface integrity. Shop‑floor advantages: predictable tool life and process security With tolerance class M and a compact plate design, the insert supports repeatable clamping and consistent positional accuracy in milling fixtures. The grade’s toughness helps resist chipping when feeds fluctuate, while the coating reduces adhesive wear on tougher materials. These material and coating choices make the insert especially useful for job shops and production cells that switch between alloyed steels, rostfreiem Stahl and heat‑resistant alloys, enabling operators and process planners to standardise cutting data around a single, reliable indexable insert family. For tailored advice on integrating the Walter Tools SDMT120408-F57 WSP45G insert into existing processes or for purchase enquiries, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for expert guidance and prompt supply Technical data Article number: SDMT120408-F57-WSP45G-WALTER Designation: SDMT120408-F57 WSP45G Product type: Fräswendeschneidplatte Brand: Walter Tools Series: Tiger‑tec Gold Grade: WSP45G Facts Relief angle: 15° Corner radius: 0.8 mm Plate size: 12 mm Plate form: Square 90° Plate thickness code: 04 Tolerance class: M Special features Chipbreaker F57 Coated carbide, Tiger‑tec Gold (PVD) Material application: P / M / S Execution: T Compact square geometry for multiple indexes FAQ Which materials can be machined with this insert? The SDMT120408-F57 WSP45G insert is specified for machining steels (P), rostfreiem Stahl (M) and heat‑resistant superalloys/titanium (S) thanks to its Tiger‑tec Gold PVD coating and the WSP45G grade. What is the advantage of the F57 chipbreaker? The F57 chipbreaker on the SDMT120408-F57 helps produce short, controllable chips and improves evacuation, reducing recutting and increasing process stability across a range of feeds and depths. How does the 15° relief influence cutting behaviour? A 15° relief angle provides a positive cutting geometry that reduces cutting forces and helps preserve the cutting edge during interrupted cuts, supporting smoother operation and prolonged tool life. How many usable edges does the square insert provide? The square 90° geometry offers multiple indexable edges, allowing cost‑efficient re‑indexing and extending the effective life of each insert under normal conditions. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned solely for explanation; there is no affiliation between Metav Werkzeuge and the named brands. The offered article is an original, factory‑new product from Walter Tools.
SDMT120412-F57 WKP35G WKP35G Wendeplatten - Walter Tools
Benefit from the combination of the Tiger‑tec Gold coating, the F57 chipbreaker and a sturdy 1.2 mm corner radius for stable, productive milling cycles; order genuine inserts from Metav Werkzeuge or consult our specialists for material‑specific recommendations. SDMT120412-F57 WKP35G milling insert — Tiger‑tec Gold, F57 chipbreaker, 1.2 mm radius SDMT120412‑F57 WKP35G is a square 90° milling insert engineered for high‑productivity steel and cast‑iron machining, featuring a coated‑carbide grade optimised for secure chip control Tiger‑tec Gold coating for extended life WKP35G grade for steel and cast iron Square 90° insert format 1.2 mm corner radius for stability F57 chipbreaker for controlled chips Reliable chip control for uninterrupted production The combination of the F57 chipbreaker and the Tiger‑tec Gold coating delivers consistent chip formation during medium‑to‑heavy milling of steels and cast irons. The chipbreaker geometry reduces the risk of long, stringy chips and helps to maintain a stable cutting zone, which in turn lowers the chance of rework and machine downtime. For applications where predictable chip evacuation and repeatable part quality matter, this insert offers a concrete advantage in process reliability and cycle‑time consistency. Geometry tailored for dimensional stability and tool life A 1.2 mm corner radius and a square 90° form provide increased edge strength and predictable wear behaviour in interrupted cuts and shoulder milling. The insert’s 15° free angle balances cutting action and workpiece engagement to reduce load spikes and lessen tool‑holder strain. Tolerance class M supports repeatable positioning in tool holders, translating to consistent component accuracy when used with appropriate milling cutters and clamping systems. Coated carbide grade for broader material coverage The WKP35G grade is a coated carbide developed for robust performance across ISO group P (steel) and K (cast iron). Its coating and substrate combination aim to resist abrasive wear from grey and spheroidal graphitic cast irons while providing thermal and chemical stability in the harsher heat conditions typical of steel machining. The result is longer in‑service life and fewer insert changes, supporting higher overall productivity and lower per‑part tooling cost in volume production. Contact Metav Werkzeuge for tailored application support, material recommendations and to secure original Walter Tools Tiger‑tec Gold inserts for production use; eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: SDMT120412-F57-WKP35G-WALTER Designation: SDMT120412-F57 WKP35G Label: Fräswendeschneidplatte SDMT120412-F57 WKP35G Walter Tools Manufacturer: Walter Tools Facts Insert size: 12 mm Corner radius: 1.2 mm Free angle: 15° Thickness code: 04 Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WKP35G (coated carbide) Chipbreaker: F57 Shape: Square 90° Suitable for: Steel (P) and Cast iron (K) Execution: T FAQ What materials is this insert recommended for? The SDMT120412‑F57 WKP35G milling insert (Walter Tools) is designed for ISO groups P and K, making it suited to machining unalloyed and alloyed steels as well as a range of cast irons. How does the F57 chipbreaker benefit machining? The F57 chipbreaker produces short, controlled chips and stabilises the cutting process, reducing the risk of chip entanglement and supporting reliable, continuous milling operations with the Tiger‑tec Gold coated insert. What does the WKP35G grade indicate? WKP35G denotes a Walter Tools coated‑carbide grade optimised for abrasive wear resistance and thermal stability; it aims to provide long tool life in mixed steel and cast‑iron production environments. Are there specific geometry advantages for interrupted cuts? Yes — the 1.2 mm corner radius and square 90° geometry enhance edge strength in interrupted and shoulder milling, improving resistance to chipping and enabling robust engagement with demanding workpiece profiles. Is this an original product from the manufacturer? The listed item is an original factory‑new Walter Tools milling insert, sold under the designation SDMT120412‑F57 WKP35G and supplied as genuine manufacturer production. Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no affiliation between our company and the brands listed. The item offered is original, factory‑new merchandise from the manufacturer Walter Tools. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
SDMT120412-F57 WPP35G WPP35G Wendeplatten - Walter Tools
The combination of Tiger·tec Gold coating and the WPP35G grade delivers extended tool life and stable chip formation for Stahl milling; the 15° relief and square 90° form with 1.2 mm corner radius enable versatile, reliable machining. Order the SDMT120412‑F57 WPP35G directly via Metav Werkzeuge or consult our specialists for application support. SDMT120412‑F57 WPP35G Fräswendeschneidplatte (for Stahl) — Tiger·tec Gold, 15° — Walter Tools The SDMT120412‑F57 WPP35G is a square indexable milling insert engineered for productive general milling of Stahl, combining a Tiger·tec Gold coating with a robust chip‑control geometry for consistent results. Tiger·tec Gold coating for increased productivity Optimised for ISO P steels 15° relief angle for flexible milling Square 90° form with 1.2 mm corner radius Consistent productivity through advanced coating and grade The coated hardmetal grade WPP35G in the Tiger·tec Gold series provides a clear efficiency advantage: enhanced wear resistance and predictable edge behaviour reduce downtime and tool changes. For machining Stahl, the coating and substrate are tuned for the typical heat generation and chip formation, which translates into longer intervals between index changes and a more consistent surface finish. The result is measurable process stability and fewer unplanned interventions on the shopfloor. Geometry designed for reliable chip control and edge life A square 90° form with a 1.2 mm corner radius and a dedicated F57 chipbreaker means the insert balances strength and cutting performance. The 15° relief angle allows a controlled engagement that reduces cutting forces in many milling scenarios and helps preserve the cutting edge when interrupted cuts or shoulder milling are required. The chipbreaker design supports short, controllable chips in continuous and semi‑continuous cuts, simplifying chip evacuation and protecting workpiece integrity — especially important when machining complex components. Practical integration and predictable results in production Tolerance class M and the specified execution support reproducible clamping and quick index changes, which eases integration into existing toolholders and production processes. The insert’s characteristics are aimed at users requiring a reliable, productive solution for typical ISO P (Stahl) applications — from roughing passes that demand stable flank life to finishing operations where surface quality matters. The combination of geometrical stability and the Tiger·tec Gold coating fosters cost‑efficient machining with lower scrap rates and fewer tool interventions. For application advice, availability or to secure the SDMT120412‑F57 WPP35G Tiger·tec Gold insert for Stahl machining, contact Metav Werkzeuge — Metav Werkzeuge GmbH is ready to assist by email (info@metav-werkzeuge.com) or phone (+49 2822 7131930) Technical Data SKU: SDMT120412-F57-WPP35G-WALTER Label: Fräswendeschneidplatte SDMT120412-F57 WPP35G Walter Tools Manufacturer: Walter Tools Series: Tiger-tec Gold Facts Relief angle: 15° Corner radius: 1.2 mm Plate size: 12 mm Plate form: Square 90° Plate thickness: 04 Tolerance class: M Special features Grade: WPP35G Chipbreaker: F57 Execution: T Material group: P (Stahl) Coating technology: Tiger·tec Gold Base designation: SDMT120412-F57 FAQ What materials is this insert suitable for? The SDMT120412‑F57 WPP35G is specified for the ISO P group, i.e. machining of Stahl, where the WPP35G grade and Tiger·tec Gold coating are optimised for the thermal and chip‑formation characteristics of these materials. How does the Tiger·tec Gold coating improve performance? The Tiger·tec Gold coating on the WPP35G grade enhances wear resistance and edge stability, offering longer tool life and more consistent machining results when the insert is used in Stahl applications. What does the F57 chipbreaker do in practice? The F57 chipbreaker promotes short, controlled chips and improves evacuation in many milling operations; this reduces the risk of re‑cutting chips and supports a stable surface finish during continuous and semi‑continuous cutting. Is the geometry suitable for shoulder and face milling? Yes, the square 90° form with a 1.2 mm corner radius and 15° relief provides a balance of edge strength and engagement geometry, making the insert suitable for a range of milling tasks, including shoulders and general face milling in Stahl. What tolerance and repeatability can be expected? Tolerance class M and the standard designation of the insert ensure consistent indexing and predictable clamping behaviour, supporting repeatable results in series production with compatible toolholders. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanation. There is no connection between our company and the mentioned brands. The offered article is original, factory‑new goods of the manufacturer. The Walter AG (brand: Walter Tools) belongs to the same corporate family and is referenced for product identification purposes only.
SDMT120412-F57 WSP45G WSP45G Wendeplatten - Walter Tools
Benefit from the combination of the Tiger·tec Gold coating and the WSP45G grade for extended cutting-edge life and reliable chip control; the square 90° geometry with a 1.2 mm corner radius delivers consistent surface finish and predictable tool life. Order the SDMT120412-F57 WSP45G directly via Metav Werkzeuge or consult our specialists for application advice. SDMT120412-F57 WSP45G milling insert – Tiger·tec Gold, square 90° by Walter Tools A SDMT120412-F57 WSP45G milling insert engineered for versatile milling of steel, stainless steel and heat‑resistant alloys with stable cutting performance Tiger·tec Gold PVD coating for long tool life Versatile grade WSP45G for P, M and S materials Square 90° plate with 1.2 mm corner radius 15° relief and SDMT120412-F57 cutting geometry Longer life through advanced coating technology The combination of the Tiger·tec Gold coating and the WSP45G grade gives a measurable improvement in wear resistance and edge stability under demanding milling conditions. The PVD-based coating reduces flank and crater wear, which extends productive tool life and supports consistent component quality. For process planners this means fewer tool changes, reduced downtime and more predictable batch runs when machining medium to heavy interrupted cuts. One grade for many materials reduces complexity Designed for the ISO material groups P, M, S, this insert covers unalloyed and alloyed steel, stainless steel and heat‑resistant superalloys or titanium. Using a single competent grade reduces tool inventory and simplifies tooling decisions across mixed-production environments. The result is improved process efficiency: stable chip formation with fewer re‑set operations and a more economical workflow for job shops and production lines alike. Geometry tuned for stability and surface consistency The square 90° plate form combined with a 1.2 mm corner radius and a 15° relief gives a balanced compromise between edge strength and surface finish. The F57 chipbreaker is engineered for controlled chip evacuation in a broad range of milling strategies, aiding surface integrity and tool life. These geometric choices support repeatable results in face and shoulder milling while keeping vibration and built‑up edge risk to a minimum. Contact Metav Werkzeuge for material‑specific recommendations and batch availability; provide the SKU SDMT120412-F57-WSP45G-WALTER and application details when calling +49 2822 7131930 or emailing info@metav-werkzeuge.com Technical Data Article number: SDMT120412-F57-WSP45G-WALTER Designation: SDMT120412-F57 WSP45G Type: milling insert Series: Tiger‑tec Gold Grade: WSP45G Manufacturer: Walter Tools Facts Plate size: 12 mm Corner radius: 1.2 mm Relief angle: 15° Plate form: Square 90° Thickness code: 04 Tolerance class: M Special features Coating: Tiger·tec Gold (PVD) Material applicability: P / M / S Chipbreaker: F57 Cutting edge form: SDMT120412-F57 Sort description: Tough, versatile PVD‑coated carbide grade for milling FAQ Which materials can this insert machine effectively? The SDMT120412-F57 WSP45G milling insert from Walter Tools is specified for ISO groups P, M and S – covering steel, stainless steel and heat‑resistant superalloys/titanium. What benefit does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating on the SDMT120412-F57 WSP45G increases wear resistance and temperature tolerance, supporting longer tool life and more consistent cutting performance in intermittent and continuous milling. How does the F57 chipbreaker influence machining? The F57 chipbreaker on this insert promotes reliable chip formation and evacuation across a wide range of milling operations, improving surface quality and reducing the risk of built‑up edge. Why choose a 1.2 mm corner radius for milling? A 1.2 mm corner radius offers enhanced edge strength and resistance to chipping while maintaining acceptable surface finish, making the insert suitable for robust milling applications. Which cutter bodies accept this insert form? This insert is intended for toolholders that accept the SDMT120412-F57 indexable insert geometry and square 90° plate forms; confirm holder compatibility with the cutter manufacturer's specifications. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are used solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product from the manufacturer.
SDMT120416-F57 WKP35G Wendeplatten - Walter Tools
High wear resistance and reliable chip control combine to deliver consistent productivity in steel and cast iron milling; the Tiger‑tec Gold grade reduces downtime and maintains surface quality. For specification or integration advice, consult Metav Werkzeuge or request tailored machining recommendations. SDMT120416-F57 WKP35G milling insert (Tiger‑tec Gold) by Walter Tools — 15° clearance, 1.6 mm corner radius The SDMT120416-F57 WKP35G is a square milling insert designed for high‑productivity cutting of steel and cast iron, optimised for stable chip formation and extended tool life. Tiger‑tec Gold coating for high wear resistance Optimised F57 chipbreaker for controlled chips 15° clearance angle for stable cutting Square 90° shape with 1.6 mm corner radius Built for durable, productive milling The combination of Tiger‑tec Gold coating and the WKP35G grade provides pronounced wear resistance, especially under the thermal and mechanical loads typical when machining steels. This coating technology reduces flank and crater wear, which translates into longer intervals between tool changes and more consistent component tolerances. The insert’s construction supports predictable tool life and helps to keep process costs down through fewer interruptions. Consistent chip control improves process stability The F57 chipbreaker is engineered to manage the short, often brittle chips produced when cutting cast iron and the continuous chips from many steels. Effective chip control reduces the risk of recutting, improves surface integrity and simplifies chip evacuation from the cutting zone. For production environments that demand repeatability, this insert stabilises cycle times and contributes to fewer rejects. Precision geometry for accurate profiles A 15° clearance angle and the square 90° geometry with a 1.6 mm corner radius deliver a balance between edge strength and profile accuracy. The clearance reduces rubbing and heat at the flank face, while the corner radius increases resistance to edge chipping during interrupted cuts. Together these features help to produce consistent surface finishes and maintain dimensional accuracy on contours and shoulders. Broad applicability with straightforward integration Designed to cover ISO groups P/K (steel and cast iron), the insert follows a production‑oriented specification suitable for many milling operations. The tolerance class M and execution code T indicate consistent fit and repeatability in standard toolholders that accept the SDMT120416‑style geometry. The series orientation towards Tiger‑tec Gold means this insert integrates readily into tool assortments where durability and process security are priorities. Fewer disruptions, better results on the shop floor By combining a robust coated grade with a targeted chipbreaker and conservative geometry, the insert supports measurable productivity gains: longer machining intervals, stable surface quality and more predictable scrap rates. Backed by the reputation of Walter Tools for dependable tooling, this solution is suitable for industrial batches where uptime and consistent part quality deliver competitive advantage. Discuss machining requirements with Metav Werkzeuge to specify the Tiger‑tec Gold WKP35G insert for your production — contact Metav Werkzeuge for tailored technical advice or to request a quotation: 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930 Technical Data Article number: SDMT120416-F57-WKP35G-WALTER Name: milling insert SDMT120416-F57 WKP35G Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WKP35G Chipbreaker: F57 Shape: Square 90° Core data Clearance angle: 15° Corner radius: 1.6 mm Insert size: 12 mm Thickness: 04 Tolerance class: M Special features Coating: Tiger‑tec Gold Grade type: WKP35G (coated carbide) Material application: Steel (P), Cast iron (K) Geometry: Square 90° Execution: T Series: Tiger‑tec Gold FAQ Which materials is the insert suitable for? The SDMT120416‑F57 WKP35G is designed for ISO groups P and K, making it suitable for machining steel and cast iron with optimised performance. What is the corner radius and why does it matter? The insert has a 1.6 mm corner radius, which increases edge strength and improves resistance to chipping, particularly on interrupted or heavy cuts with the SDMT120416‑F57 WKP35G. Which coating and grade does the insert use? This insert uses the Tiger‑tec Gold coating and the WKP35G grade, offering enhanced wear resistance and thermal stability for demanding milling tasks. How does the F57 chipbreaker affect machining? The F57 chipbreaker provides controlled chip formation and evacuation, reducing the likelihood of recutting and supporting consistent surface quality on both steel and cast iron. Is the insert compatible with standard SDMT120416 toolholders? Yes, the geometry and tolerance class M align with holders designed for the SDMT120416 family, enabling straightforward integration into existing tool assemblies. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only and do not imply any affiliation between our company and the trademark owners. The item offered is an original, brand‑new product from the respective manufacturer.
SDMT120416-F57 WKP35S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, a proven WKP35S grade and a 15° free cutting angle for high productivity and reliable chip control in steel and cast iron machining — order the milling insert directly via Metav Werkzeuge or ask the consultants if needed. SDMT120416-F57 WKP35S milling insert — square 90°, 1.6 mm radius, for steel and cast iron — Walter Tools The SDMT120416-F57 WKP35S is a square 90° milling insert designed for high‑productivity machining of steel and cast iron with a Tiger·tec Silver coated carbide grade. Tiger·tec Silver coating technology Suited for steel and cast iron (P / K) Square 90° form with 1.6 mm radius 15° free cutting angle, chipbreaker F57 Consistent high productivity through advanced coating and grade The combination of Tiger·tec Silver coating and the WKP35S grade provides a balanced defence against abrasive wear and thermal loads typical of turning and milling steels and cast irons. The coating reduces friction at the cutting edge and extends the usable life of the insert, which directly translates into fewer tool changes and higher uptime on the shop floor. Effective chip control via the F57 chipbreaker improves swarf management in interrupted cuts and mixed material batches, supporting stable cycle times and predictable process planning. Geometry that improves surface quality and repeatability A square 90° plate form with a 1.6 mm corner radius and a 15° free cutting angle delivers robust engagement and reliable edge support under varying cutting conditions. The geometry enhances load distribution at the cutting zone, reducing edge chipping and ensuring consistent component finish. With a tolerance class M, this insert offers repeatable dimensions for serial production, enabling close toolpath tolerances and dependable assembly fits. The solid, coated carbide construction provides dimensional stability through the life of the insert, which benefits both roughing passes and prestressed finishing operations. Practical integration and process benefits for series machining Specifically developed for the machining demands of steel (P) and cast iron (K), this insert fits standard square milling toolholders and is easy to index when an edge change is needed. The SDMT120416‑F57 WKP35S supports a broad range of cutting parameters, allowing process engineers to optimise feeds and speeds for either higher metal removal rates or finer surface appearance. Selecting this grade reduces the number of different inserts required across mixed production runs, which simplifies inventory and increases operational flexibility. In short, the insert helps secure stable cycle times and repeatable component quality across batch sizes. For tailored advice on Walter Tools Tiger·tec Silver inserts such as the SDMT120416‑F57 WKP35S, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for rapid, application‑specific recommendations Technical Data Article number: SDMT120416-F57-WKP35S-WALTER Article name: Milling insert SDMT120416-F57 WKP35S Manufacturer: Walter Tools Core technical data Plate size: 12 mm Plate thickness: 4 mm Corner radius: 1.6 mm Free cutting angle: 15° Tolerance class: M Designs and special features Coating / series: Tiger·tec Silver Grade: WKP35S (coated carbide) Chipbreaker: F57 Form: Square 90° Material suitability: Steel (P) and Cast iron (K) Version: T Series notes: Optimised for heat and chip formation when machining steel and for abrasive wear characteristics of cast iron FAQ What materials is this insert suitable for? The SDMT120416‑F57 WKP35S is specified for machining steel (P) and cast iron (K), reflecting the Tiger·tec Silver grade’s balance of wear resistance and toughness. How does the F57 chipbreaker affect performance? Chipbreaker F57 supports consistent chip formation and evacuation in mixed and interrupted cuts; the configuration reduces recutting and helps maintain surface quality with the WKP35S grade. What benefit does the 1.6 mm corner radius provide? A 1.6 mm corner radius increases edge strength for heavy engagement cuts and contributes to improved surface finish compared with smaller radii, while remaining suitable for common finishing passes. Is the insert compatible with standard square milling toolholders? Yes. The square 90° form and standard dimensions make it compatible with many indexable milling cutters designed for SDMT‑style inserts. Why choose Tiger·tec Silver with the WKP35S grade? Tiger·tec Silver coating combined with the WKP35S coated carbide grade offers a compromise of toughness and abrasion resistance, aimed at reducing downtime and providing consistent tool life in production environments. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes; there is no affiliation between our company and the mentioned brands. The offered article is an original, factory‑new product of the manufacturer.
SDMT120416-F57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of a high-process-security insert that combines Tiger·tec Gold coating, precise 15° clearance and the F57 chipbreaker for consistent chip control and long tool life; order directly via Metav Werkzeuge or contact our consultants for application advice. SDMT120416-F57 WSP45G milling insert — Tiger·tec Gold, 15° clearance (Walter Tools) SDMT120416-F57 WSP45G is a milling indexable insert designed for productive finishing and medium-duty roughing across steels, rostfreier Stahl and heat‑resistant alloys Tiger·tec Gold PVD coating Versatile P/M/S material range 15° clearance angle for stability 1.6 mm corner radius for strength Greater process reliability for mixed-material production The Tiger·tec Gold technology provides a robust, PVD-coated cutting edge that supports stable performance across a broad material spectrum. The grade WSP45G is formulated for productive milling, reducing the tendency for build-up and maintaining a consistent cutting geometry. For operations producing variable batches, the combination of coating and substrate reduces unplanned tool changes and helps maintain surface quality, translating into higher uptime and predictable cycle times. Stable cutting edge and predictable tool life A positive clearance of 15° and a 1.6 mm corner radius deliver a reliable balance between edge strength and geometric precision. The M tolerance class ensures dimensional repeatability for toolholders and pocket fits, while the F57 chipbreaker supports controlled chip formation in interrupted and continuous cuts. These factors contribute to extended tool life and reduced rework, which improves throughput and lowers overall machining cost per component. Application advice and suitability across ISO groups Designed for ISO groups P/M/S, this insert is suitable for machining Stahl, rostfreier Stahl and superalloys / titanium under demanding thermal and mechanical conditions. The designation emphasises adaptability: P for general steels, M for rostfreier Stahl where heat and adhesion are critical, and S for high-temperature alloys requiring a heat-resistant cutting edge. For customers seeking process stability and consistent surface finish, this insert offers a clear technical advantage in mixed‑material production environments. If additional cutting data or optimisation support is required, Metav Werkzeuge provides technical consultation and further cutting recommendations. Contact Metav Werkzeuge for tailored cutting-data sheets and application support for Walter Tools Tiger·tec Gold inserts Technical data SKU: SDMT120416-F57-WSP45G-WALTER Article designation: SDMT120416-F57 WSP45G Product type: Fräswendeschneidplatte (milling insert) Series: Tiger-tec Gold Grade: WSP45G Manufacturer: Walter Tools Numbers / Core technical data Size: 12 Corner radius: 1.6 mm Relief angle: 15° Thickness: 04 Tolerance class: M Designs / Special features Chipbreaker: F57 Substrate/coating: coated cemented carbide (Tiger·tec Gold / PVD) Execution: T Plate form: Square 90° Material suitability: P / M / S (Stahl, rostfreier Stahl, superalloys/titanium) FAQ What materials can be machined with this insert? The SDMT120416-F57 WSP45G from Walter Tools is suitable for P/M/S groups, meaning it machines Stahl, rostfreier Stahl and heat‑resistant alloys including titanium and superalloys. How does the F57 chipbreaker affect machining? The F57 chipbreaker on the SDMT120416-F57 WSP45G promotes predictable chip formation and evacuation, improving surface finish and reducing the risk of chip jamming in both continuous and interrupted milling. Is this insert suitable for finishing and roughing operations? Yes; the combination of 1.6 mm corner radius and Tiger·tec Gold coating on the Walter Tools insert balances edge strength and sharpness, making it suitable for finishing and medium roughing where process stability is required. What does the M tolerance class mean for toolholders? Tolerance class M indicates consistent dimensional accuracy of the insert, ensuring reliable seating in the toolholder and repeatable tool offsets for precision milling with Walter Tools inserts. Can the SDMT120416-F57 WSP45G handle high‑temperature materials? The WSP45G grade and Tiger·tec Gold coating are engineered for heat resistance and edge stability, making the insert appropriate for many high‑temperature alloy applications within the S group. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SDMT120420-F57 WKP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold wear resistance, a WKP35G coated-carbide grade and precise geometry for reliable milling of steel and cast iron; order directly via Metav Werkzeuge or ask the consultants for application advice. SDMT120420-F57 WKP35G — Milling insert, Tiger·tec Gold, Walter Tools The SDMT120420-F57 WKP35G is a square 90° milling insert engineered for high-productivity machining of steel and cast iron in demanding milling operations. Tiger·tec Gold coating for wear resistance Coated-carbide WKP35G grade for long life Optimised F57 chipbreaker for consistent chips Square 90° form with 15° relief and r 2 mm Longer tool life through advanced coating technology The combination of Tiger·tec Gold coating and the WKP35G grade creates a cutting edge that is resistant to the typical abrasive and thermal stresses encountered when machining steel and cast iron. The coated-carbide construction reduces flank and crater wear, which translates into fewer tool changes and improved process uptime. For production-focused shops, this results in a measurable improvement in overall tool economy while maintaining consistent cutting performance across batches. Consistent surface quality and reproducible geometry The square 90° form and a corner radius of 2 mm deliver robust edge strength and predictable engagement in slotting and face milling operations. The insert’s 15° relief geometry supports stable cutting conditions and helps to maintain surface finish repeatability. With tolerance class M, the insert fits standard toolholders with reliable seating, reducing variation between successive assemblies and supporting reproducible component quality. Chip control that supports faster cycle times Equipped with the F57 chipbreaker, the insert controls chip formation to favour short, manageable chips when cutting both steel and cast iron. Improved chip control reduces interruptions, protects the workpiece and toolholder, and facilitates safer, higher-feed machining strategies. The result is an efficient, deterministic process that supports higher material removal rates without compromising tool life. Application scope and operational guidance The insert is designed primarily for machining applications classified under ISO group P (steel) and K (cast iron), reflecting its balanced toughness and abrasive-wear resistance. The coated-carbide substrate and P/K suitability make the insert appropriate for a wide range of operations—from medium-duty finishing to more productive roughing passes—provided cutting parameters are adapted to the workpiece material and machine capability. For specification of feed and speed windows, refer to tooling charts or consult application engineering. Contact Metav Werkzeuge for tailored recommendations on tooling assemblies and to discuss the best insert grade for specific steel or cast iron applications — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: SDMT120420-F57-WKP35G-WALTER SKU: SDMT120420-F57-WKP35G-WALTER ISO designation: SDMT120420-F57 WKP35G Grade: WKP35G Series: Tiger·tec Gold Product type: Milling insert Facts Plate form: Square 90° Plate size: 12 Plate thickness: 04 Relief angle: 15° Corner radius: 2 mm Chipbreaker: F57 Tolerance class: M Special features Material suitability: P / K (steel and cast iron) Coated-carbide grade for wear resistance Execution: T Designed for productive milling applications Optimised chip control for consistent chips FAQ What materials is this insert suitable for? The SDMT120420-F57 WKP35G insert is specified for ISO groups P and K, meaning it is suitable for machining steel and cast iron. What does the WKP35G grade offer? WKP35G is a Walter coated‑carbide grade within the Tiger·tec Gold family that balances wear resistance and toughness for productive machining of steels and cast irons. Which chipbreaker is fitted and what is the benefit? The insert uses the F57 chipbreaker, designed to produce short, controllable chips that support uninterrupted, higher‑productivity milling. How does the square 90° form affect application choice? The square 90° geometry provides strong cutting edges for slotting and face milling and enables use in a wide range of milling strategies where robust corner strength is required. Is the insert compatible with standard toolholders? With tolerance class M and standard ISO designation, the insert is intended to fit compatible toolholders designed for this insert form and size. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Die Walter AG (brand name: Walter Tools) gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des Sandvik‑Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SDMT120420-F57 WKP35S Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Silver performance and the WKP35S grade for reliable chip control and extended tool life; the combination of a F57 chipbreaker and a robust 2 mm corner radius ensures stable production in steel and cast iron applications — order or request machining advice via Metav Werkzeuge. SDMT120420-F57 WKP35S Tiger·tec Silver indexable milling insert by Walter Tools — F57 chipbreaker, 15° relief angle The SDMT120420-F57 WKP35S is a Tiger·tec Silver indexable milling insert engineered for productive machining of steel and cast iron in general milling applications. Tiger·tec Silver coating, WKP35S grade Square 90° insert with 2 mm corner radius F57 chipbreaker for controlled chip formation For steel (P) and cast iron (K) machining Improved machining performance through modern coating technology The combination of the Tiger·tec Silver coating and the WKP35S substrate delivers a balance between wear resistance and edge stability that raises process reliability. The advanced coating reduces abrasive and adhesive wear during interrupted cuts and high thermal loads, which means longer intervals between index changes and fewer unplanned tool interventions. As a result, machining centres experience more consistent cycle times and improved overall productivity when processing steel and cast iron according to ISO 513 classifications. Geometry engineered for strength and surface quality The square 90° geometry with a 2 mm corner radius and a 15° relief angle provides a robust cutting edge suited to both roughing and semi-finishing operations. The substantial corner radius increases edge strength under heavier depths of cut, while the moderate relief angle supports effective chip evacuation and stable cutting forces. The integrated F57 chipbreaker further refines chip formation, promoting short, broken chips that reduce the risk of entanglement and improve surface finish on the workpiece. These features together lower tool change frequency and support predictable component quality. Versatile application scope and process guidance Classified for material groups P (steel) and K (cast iron), the insert is suitable for a wide range of industrial milling tasks where balanced wear resistance and reliable chip control are required. The medium tolerance class M and the insert’s layout make it appropriate for shops seeking repeatable performance across mixed batches of unalloyed, alloyed steels and various cast irons. Selection of the SDMT120420-F57 WKP35S is recommended where a compromise between edge life and finish quality is desired, and where the machining strategy benefits from the insert’s predictable behaviour under standard cutting conditions. Contact Metav Werkzeuge for specification support or to discuss how the SDMT120420-F57 WKP35S by Walter Tools fits the machining process at hand — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data Article number: SDMT120420-F57-WKP35S-WALTER SKU: SDMT120420-F57-WKP35S-WALTER Label: Fräswendeschneidplatte SDMT120420-F57 WKP35S Walter Tools Product type: Fräswendeschneidplatte (indexable milling insert) Facts Relief angle: 15° Corner radius: 2 mm Inscribed circle / size: 12 mm Thickness: 4 mm Tolerance class: M Special features Series: Tiger·tec Silver Grade: WKP35S (coated carbide) Chipbreaker: F57 Plate form: Square 90° Material suitability: Steel (P), Cast iron (K) Execution: T FAQ What materials are best suited to this insert? The SDMT120420-F57 WKP35S insert is designed primarily for steel (P) and cast iron (K) applications, using the Tiger·tec Silver coating to manage heat and abrasive wear. How does the F57 chipbreaker influence machining? The F57 chipbreaker on this Walter Tools insert promotes controlled, broken chips, improving chip flow and reducing the likelihood of chip-related interruptions during milling. Which geometries and operations benefit most from the 2 mm corner radius? A 2 mm corner radius increases edge robustness for heavier engagement and is particularly beneficial in roughing and semi-finishing where edge strength and load distribution are critical. Is this insert suitable for finishing work? The SDMT120420-F57 WKP35S offers a compromise between wear resistance and surface quality; fine finishing is possible with appropriately tuned cutting parameters and machine rigidity. What does the tolerance class M indicate for shop planning? Tolerance class M denotes medium tolerances appropriate for many general machining tasks, balancing interchangeability with reasonable manufacturing cost. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SDMT120420-F57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of the combination of a Tiger‑tec Gold PVD-coated grade and a robust F57 chipbreaker to keep milling cycles productive and predictable; the insert’s square 90° form with a 2 mm corner radius and 15° clearance angle supports consistent surface quality and tool life. Order original Walter Tools inserts or consult Metav Werkzeuge’s technical team for selection and application advice. SDMT120420-F57 WSP45G — Milling insert, Tiger‑tec Gold, square 90° (r2) by Walter Tools The SDMT120420-F57 WSP45G is a square milling insert designed for versatile milling of steel, stainless steel and heat‑resistant alloys in industrial production environments. *Tiger‑tec Gold PVD coating *Suitable for steel, stainless and superalloys *Square 90° geometry, r2 corner *15° clearance angle for stable cutting Reliable edge stability and consistent productivity The combination of the Tiger‑tec Gold technology and the WSP45G grade delivers a PVD‑coated carbide chemistry optimised for toughness and edge security under milling loads. This configuration supports stable chip formation when machining common workshop steels and the more demanding stainless and heat‑resistant materials. The result is fewer unscheduled tool changes and more predictable cycle times, which directly improves throughput and reduces machining cost per part. Predictable chip control and improved surface finish The integrated F57 chipbreaker, together with the square 90° geometry and 2 mm corner radius, gives controlled chip splitting and evacuation across a range of cutting parameters. The 15° clearance reduces rubbing on the workpiece and helps maintain dimensional accuracy. These features combine to lower the need for finishing passes and to produce a better surface quality straight from the milling operation. Broad material capability with economical performance Engineered for the ISO groups P, M and S, this insert is suitable for machining unalloyed and alloyed steel, stainless steel and heat‑resistant superalloys including titanium. The grade’s balance of toughness and wear resistance extends effective tool life in mixed‑material production environments, offering a practical route to lower tooling costs through fewer index changes and reduced scrap rates. Practical handling and inventory benefits The standardised designation and consistent geometry simplify tooling logistics and inventory management in the workshop. The insert’s tolerance class M supports repeatable seating and stable clamping, which eases set‑up and replacement. For specific cutter body compatibility, cutting data or process optimisation, Metav Werkzeuge’s consultants provide application‑oriented advice to integrate this insert into existing machining processes. Contact Metav Werkzeuge for tailored machining recommendations and to request original Walter Tools SDMT120420‑F57 WSP45G inserts; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitable cutting parameters and availability Technical data Article number: SDMT120420-F57-WSP45G-WALTER Designation: SDMT120420-F57 WSP45G Manufacturer: Walter Tools Core specifications Plate size: 12 Plate thickness: 04 Clearance angle: 15° Corner radius: 2 Plate form: Quadrat 90° Tolerance class: M Chipbreaker: F57 Grade: WSP45G Materials & special features Series: Tiger‑tec Gold (PVD‑coated carbide) Suitable for: P (steel), M (stainless steel), S (superalloys / titanium) Execution: T Robust chip control and stable cutting edge Designed for productive milling applications FAQ What materials is this insert suitable for? The SDMT120420‑F57 WSP45G insert is designed for steel (P), stainless steel (M) and superalloys/titanium (S); its Tiger‑tec Gold PVD grade balances toughness and wear resistance for those groups. Which chipbreaker and corner radius does the insert use? The insert uses the F57 chipbreaker and a 2 mm corner radius to promote controlled chip formation and consistent part finish during milling. What is the insert geometry and clearance angle? This indexable insert has a square 90° form with a 15° clearance angle, suited to stable shoulder and face milling where rigidity and accuracy are needed. How does the Tiger‑tec Gold series benefit production? Tiger‑tec Gold delivers a PVD‑coated carbide surface that enhances edge stability and wear resistance, improving tool life and reducing downtime in repetitive milling tasks. Is the grade suitable for mixed‑material production? Yes — the WSP45G grade is positioned for versatile use across P, M and S workpiece groups, offering consistent performance in mixed‑material batches. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only and do not indicate any affiliation between our company and the listed brands. The offered article is an original, factory‑new product from the manufacturer Walter Tools.
SDMT120425-F57 WKP35G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold grade and a precise 2.5 mm corner radius for consistent edge life and predictable surface finish; the design suits high‑productivity milling of steel and cast iron. Order the insert directly via Metav Werkzeuge or contact the consultants for application advice. SDMT120425-F57 WKP35G milling insert — square 90° with 15° relief | Walter Tools The SDMT120425-F57 WKP35G is a square 90° milling insert designed for medium to heavy milling of steel (P) and cast iron (K), combining a stable cutting edge with Tiger‑tec Gold coating for extended tool life. Tiger‑tec Gold for extended tool life WKP35G grade for steel and cast iron Square 90° geometry for versatile milling Chipbreaker F57 for controlled swarf evacuation High productivity through material‑matched grade The Tiger‑tec Gold WKP35G grade delivers stable cutting performance in both steel and cast iron, reducing flank wear under typical machining temperatures. The coated cemented carbide composition is engineered for abrasive resistance and thermal stability, which translates into fewer tool changes and longer uninterrupted production runs. This reliability supports predictable cycle times and improved process efficiency in demanding batch and continuous operations. Geometry that improves dimensional consistency The square 90° insert form with a 15° relief angle and 2.5 mm corner radius provides a balance between edge strength and fine surface finish. The insert geometry minimises deflection in slotting and peripheral milling, contributing to repeatable part tolerances and reduced rework. For workshops looking to standardise tooling, this geometry enables versatile use across a range of cutter bodies and milling strategies without sacrificing accuracy. Chip control and machining stability for easier handling The F57 chipbreaker is tailored to produce short, manageable chips in interrupted and continuous cuts, reducing the risk of chip entanglement and improving operator safety. Controlled swarf formation also helps maintain consistent contact at the cutting edge, which supports surface quality and reduces the load on coolant systems. Combined with the Tiger‑tec Gold coating, the insert resists built‑up edge and maintains a stable cutting edge over longer tool lives. For milling applications requiring a robust, grade‑optimised solution, request availability and technical recommendations from Metav Werkzeuge — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: SDMT120425-F57-WKP35G-WALTER Name: Fräswendeschneidplatte SDMT120425-F57 WKP35G Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WKP35G Numbers / Core technical data Relief angle: 15° Corner radius: 2.5 mm Insert size: 12 mm Tolerance class: M Design / Special features Shape: Square 90° Chipbreaker: F57 Thickness code: 04 Material designation: P / K (steel / cast iron) Execution: T FAQ What materials is this insert suitable for? The SDMT120425-F57 WKP35G insert is intended for steel (P) and cast iron (K), utilising the WKP35G grade for balanced wear resistance and thermal stability. How does the Tiger‑tec Gold coating benefit machining? Tiger‑tec Gold on the SDMT120425-F57 WKP35G enhances thermal resistance and reduces abrasive wear, extending tool life and improving consistency in surface finish. Which chip conditions are expected with chipbreaker F57? Chipbreaker F57 is designed to produce short, controlled chips in both continuous and interrupted milling, aiding swarf evacuation and machining stability. Is the insert geometry suitable for heavy roughing passes? Yes, the square 90° form with a 2.5 mm corner radius and 15° relief provides edge strength and resistance to deflection suitable for robust milling operations. Can this insert be used in standard cutter bodies for SDMT‑style inserts? The SDMT120425-F57 WKP35G matches standard cutter configurations for SDMT‑type indexable inserts; confirm seat compatibility with the chosen cutter body before mounting. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners and are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is an original, factory‑new product of the manufacturer.
SDMT120425-F57 WPP35G Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Gold coating and the WPP35G grade for reliable steel machining, paired with a 15° clearance and a 2.5 mm corner radius for stable cutting performance. Order the insert via Metav Werkzeuge or consult our specialists for application advice. SDMT120425-F57 WPP35G milling indexable insert for steel – Walter Tools A SDMT120425-F57 WPP35G milling insert engineered for efficient steel machining, combining the Tiger‑tec Gold coating with an optimised F57 chipbreaker for consistent chip control. Tiger‑tec Gold coated, wear‑resistant grade WPP35G 15° clearance angle for stable cutting 2.5 mm corner radius, square 90° insert Optimised F57 chipbreaker for steel machining High process efficiency through coating and grade The coated carbide grade WPP35G from the Tiger‑tec Gold series is tailored for the thermal and chip‑forming behaviour typical of steel machining. The combination of a wear‑resistant coating and a balanced substrate reduces flank wear and extends tool life, which translates into fewer index changes and improved uptime. This performance advantage supports higher metal removal rates while maintaining dimensional stability, so operations benefit from measurable productivity gains. Stable cutting geometry for predictable results A 15° clearance angle and a 2.5 mm corner radius provide a robust cutting edge that absorbs cutting forces and reduces vibration during face and shoulder milling. The square 90° form ensures full‑shoulder capability and simple orientation in standard toolholders. The insert’s F57 chipbreaker is optimised for continuous and segmented chips in steel, improving evacuation and reducing the risk of built‑up edge; this leads to better surface finish and consistent component tolerances in serial production. Practical benefits for workshop integration The insert is supplied in the SDMT form factor and is compatible with common milling tool assemblies, delivering straightforward tool setup and predictable reconditioning intervals. As the grade is specified for ISO group P (steel), selection for a steel‑focused tool inventory becomes simpler and more cost‑effective. Technical teams will value the clear designation and repeatable behaviour of the grade when standardising process parameters across machines. Contact Metav Werkzeuge today to confirm suitability of the Walter Tools Tiger‑tec Gold SDMT120425-F57 WPP35G insert for specific steel applications – info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: SDMT120425-F57-WPP35G-WALTER Manufacturer: Walter Tools Product type: Milling indexable insert Core specifications Corner radius: 2.5 mm Clearance angle: 15° Insert size designation: 12 Thickness code: 04 Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WPP35G (coated carbide) Chipbreaker: F57 Shape: Square 90° Application: Steel (ISO P) Form designation: SDMT120425-F57 FAQ What materials is this insert suited for? The SDMT120425-F57 WPP35G is specified for ISO group P and is optimised for machining various steels; the WPP35G grade and Tiger‑tec Gold coating address steel‑typical heat and chip conditions. How does the F57 chipbreaker affect performance? The F57 chipbreaker promotes controlled chip formation in steel, improving evacuation and surface finish while reducing the tendency for built‑up edge on the cutting zone. Can this insert be used for shoulder milling? Yes, the square 90° form and a 2.5 mm corner radius make the insert suitable for face and shoulder milling operations in steel. What are the key dimensional data to check before mounting? Verify the insert designation SDMT120425-F57, the 15° clearance angle, the 2.5 mm corner radius and the thickness code to ensure compatibility with the chosen toolholder. Is this an original Walter Tools product? The article is an original factory‑new insert from Walter Tools; the product designation and grade reflect the manufacturer’s catalogue specification. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are used for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is an original, factory‑new product of the manufacturer.
SDMT120425-F57 WSM35G WSM35G Wendeplatten - Walter Tools
Take advantage of the high thermal stability and stable edge life of the WSM35G grade together with the predictable chip control from the F57 breaker to keep production running without frequent tool changes; order the insert directly via Metav Werkzeuge or ask the consultants for tailored recommendations. SDMT120425-F57 WSM35G Fräswendeschneidplatte (Square 90°, R2.5) by Walter Tools SDMT120425-F57 WSM35G is a square milling indexable insert designed for demanding work in rostfreier Stahl and heat-resistant alloys, combining Tiger·tec Gold coating with a robust geometry for reliable material removal Tiger·tec Gold coated carbide grade WSM35G Optimised for rostfreier Stahl and superalloys Square 90° insert with 2.5 mm corner radius 15° clearance and F57 chipbreaker design Reliable performance in rostfreier Stahl and superalloys The SDMT120425-F57 WSM35G insert is built on the Tiger·tec Gold coating platform and the WSM35G cutting grade to address the thermal and mechanical stresses of machining rostfreier Stahl and high-temperature alloys. The coated carbide substrate increases resistance to abrasive wear and heat, which reduces the formation of built-up edge and extends tool life. For operations where thermal load is high, this combination supports stable chip formation and predictable wear patterns, thereby improving machining consistency and reducing unplanned tool changes. Controlled chips and improved surface quality The engineered F57 chipbreaker geometry promotes short, controllable chips even when cutting sticky or ductile materials. Shorter chips reduce the risk of entanglement and make chip evacuation more reliable, which contributes to a better surface finish and fewer interruptions on automated lines. In process terms, the chipbreaker reduces cutting forces peaks and supports continuous material flow from the cutting zone, helping to maintain steady spindle loads and consistent part quality during longer production runs. Geometry that supports strength and accuracy A square 90° shape with a 2.5 mm corner radius and 15° clearance delivers a balance between edge strength and cutting precision. The larger corner radius increases edge robustness for heavier engagement, while the defined clearance angle helps prevent rubbing and heat build-up on the flank. The insert’s thickness code and M tolerance class ensure repeatable seating and positioning in compatible toolholders, which is essential for maintaining dimensional accuracy across batches and for predictable tool indexing cycles. Practical application and efficiency gains Assigned to material groups S / M under ISO 513, this insert is suited to heavy-duty and high-heat tasks as well as many stainless steel applications depending on the chosen tool geometry. The combined effect of the coating, grade and chipbreaker is improved productivity through longer cutting intervals and reduced downtime for tool change. For production environments prioritising process stability and cycle-time efficiency, this grade offers a cost-effective way to extend operating windows and increase machine utilisation without sacrificing surface integrity. For machining rostfreier Stahl or superalloys, consult Metav Werkzeuge for holder compatibility and supply of Walter Tools inserts to secure optimal process parameters and timely delivery Technical Data SKU: SDMT120425-F57-WSM35G-WALTER Article designation: SDMT120425-F57 WSM35G Series: Tiger·tec Gold Grade: WSM35G Manufacturer: Walter Tools Core data Free angle: 15° Corner radius: 2.5 mm Insert shape: Square 90° Insert size: 12 Thickness code: 04 Tolerance class: M Special features Coating: Tiger·tec Gold (coated carbide) Chipbreaker: F57 Material groups: S / M Suitable for: rostfreier Stahl and heat-resistant superalloys Application focus: Stable cutting and process security FAQ What materials is this insert designed for? The SDMT120425-F57 WSM35G insert from Walter Tools is formulated for rostfreier Stahl and heat-resistant superalloys (ISO groups M and S), offering thermal stability and wear resistance for difficult-to-cut materials. How does the F57 chipbreaker help production? The F57 chipbreaker on the SDMT120425-F57 reduces chip length and manages chip evacuation, which improves the surface finish and lowers the risk of chip-related stoppages during continuous milling operations. What is the effect of the 2.5 mm corner radius? A 2.5 mm corner radius increases edge strength for heavier cutting engagements and supports longer tool life; in the SDMT120425-F57 this contributes to more tolerant cutting conditions and fewer tool changes. Which dimensions and tolerance class apply to this insert? The insert is a square 90° type with size 12, thickness code 04 and tolerance class M; these parameters ensure stable seating and reproducible indexing in matching toolholders. Is this insert suitable for finishing or roughing operations? The WSM35G grade and Tiger·tec Gold coating target high thermal and mechanical stresses, making the SDMT120425-F57 suitable for heavy-duty cutting; depending on tool geometry, it can also be applied to finishing tasks in rostfreier Stahl. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools), headquartered in Tübingen, is among the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
SDMT120425-F57 WSM45X WSM45X Wendeplatten - Walter Tools
Take advantage of a coated carbide grade designed for the machining of difficult-to-cut alloys and stainless steel, combined with a robust F57 chipbreaker and a 15° relief for secure cutting performance; order the insert via Metav Werkzeuge or contact our consultants for tailored advice and application support. SDMT120425-F57 WSM45X milling indexable insert by Walter Tools — 15° relief, 2.5 mm corner radius SDMT120425-F57 WSM45X is a square milling insert engineered for demanding machining of stainless and high-temperature alloys, offering secure chip control and long tool life for heavy-duty milling applications. Coated carbide for demanding alloys F57 chipbreaker for controlled chip flow 15° relief angle for lower cutting forces 2.5 mm corner radius for edge strength Consistent cutting performance in demanding alloys The WSM45X grade is a coated carbide designed specifically for materials that are difficult to machine. The advanced coating and carbide combination promote stable cutting edges, reducing the tendency for built-up edge in stainless steel and heat-resistant superalloys. Stability at the cutting edge translates directly into fewer tool changes and more predictable cycle times, which supports continuous production and lowers overall machining costs. The insert geometry is balanced to preserve surface integrity while enabling reliable material removal in challenging workpiece conditions. Optimised geometry for process security and surface quality The F57 chipbreaker and 15° relief angle work together to control chip formation and reduce cutting forces. The chipbreaker grooves are tailored to break and evacuate chips efficiently during interrupted or continuous milling, minimising re-cutting and improving tool life. The square 90° format with a 2.5 mm corner radius provides a strong cutting edge that tolerates higher radial depths of cut, making the insert suitable for both roughing and semi-finishing operations where edge stability and repeatable surface quality are required. Seamless integration with tool systems and economical productivity The insert is supplied in the SDMT120425-F57 format with a compact size that integrates into common indexable milling holders. Classified with tolerance class M and a material suitability of S / M, it is intended for stainless steel and heat-resistant alloys, ensuring broad applicability across aerospace, power generation, and specialised manufacturing. Choosing this insert supports process reliability through longer tool life and predictable wear behaviour; reduced downtime and consistent component quality together yield measurable productivity gains. For specification matching, cutting data recommendations or to source Walter Tools inserts like the SDMT120425-F57 WSM45X for stainless steel machining, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for expert guidance and rapid delivery Technical Data Article number: SDMT120425-F57-WSM45X-WALTER Designation: SDMT120425-F57 WSM45X Type: Milling indexable insert Series: Walter Schneidstoffsorte - Serie offen Grade: WSM45X Manufacturer: Walter Tools Facts Relief angle: 15° Corner radius: 2.5 mm Shape: Square 90° Size: 12 mm Thickness: 4 mm Tolerance class: M Special features Chipbreaker: F57 Material suitability: S / M (heat-resistant alloys / stainless steel) Coating: Coated hardmetal (coated carbide) Execution: T FAQ What materials is this insert suited for? The SDMT120425-F57 WSM45X insert is specified for stainless steel and heat-resistant superalloys (material groups M and S), making it suitable for tough, heat-retaining workpieces. How does the F57 chipbreaker improve milling performance? The F57 chipbreaker on this milling insert promotes controlled chip formation and evacuation, which reduces re-cutting, lowers cutting forces and enhances the durability of the cutting edge. Which applications benefit most from the 2.5 mm corner radius? A 2.5 mm corner radius provides increased edge strength for heavier cuts and interrupted milling, so roughing and semi-finishing operations in demanding materials gain the most benefit. Is this insert compatible with standard indexable milling holders? The SDMT120425-F57 format is designed to fit common square insert toolholders; compatibility should be confirmed against the holder specification before assembly. What does the WSM45X grade offer compared with general-purpose grades? WSM45X is a purpose-designed coated carbide grade optimised for thermal resistance and stable edge life in difficult-to-cut stainless steels and superalloys, offering improved process security over generic grades. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is an original, factory-new product of the manufacturer.
SDMT120425-F57 WSP45G WSP45G Wendeplatten - Walter Tools
Take advantage of a wear‑resistant PVD coating and a robust geometry for reliable milling performance; the combination of the Tiger‑tec Gold grade and a 2.5 mm corner radius promotes stable chip formation and extended tool life. Order directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. SDMT120425-F57 WSP45G square milling insert – Tiger‑tec Gold, for P/M/S applications (Walter Tools) SDMT120425-F57 WSP45G is a square 90° indexable milling insert engineered for high‑productivity milling of steel, stainless steel and heat‑resistant alloys Tiger‑tec Gold PVD grade WSP45G Square 90° insert, 2.5 mm corner radius Suitable for steel, stainless and superalloys 15° relief angle for stable cutting Consistent wear resistance for longer tool life The Tiger‑tec Gold coating is a PVD‑based system optimised for milling, offering a balance between hardness and toughness. This combination reduces flank and crater wear under the high temperatures typical of milling processes, resulting in improved tool life and fewer insert changes. The WSP45G grade is specified for versatile performance across a broad range of steels and heat‑resistant materials; its coated carbide substrate supports secure edge retention during repeated passes. For production environments this translates into predictable cycle times and a reduction in downtime related to tool management. Geometry that increases process stability and surface quality A square 90° plate with a 2.5 mm corner radius delivers high edge strength for interrupted cuts and heavy engagement typical of shoulder milling. The 15° relief angle reduces rubbing at the flank while maintaining support behind the cutting edge, which helps to avoid built‑up edge and to produce a consistent surface finish. The insert form and edge preparation suit both roughing and semi‑finishing operations where stability and repeatability are decisive. In practise, the geometry lowers the risk of premature edge failure and supports higher feed rates with maintained surface integrity. Versatile grade for demanding materials and controlled chip formation Designed for materials classified under ISO groups P, M and S, this insert handles unalloyed and alloyed steel, stainless steel and high‑temperature superalloys and titanium components. The WSP45G grade promotes stable chip formation even where heat dissipation is limited, supporting safer machining of materials that tend to work‑harden or strain‑soften. Where process security and consistent reproducibility are required, the combination of coated carbide and optimised chipbreaker (F57) contributes to smoother swarf flow, reduced recutting and more consistent surface results on each workpiece. For fast procurement of Walter Tools Tiger‑tec Gold inserts or advice on optimal cutting parameters, contact Metav Werkzeuge — our consultants will recommend the suitable insert and grade for the specific material and machining strategy. Technical data Article number: SDMT120425-F57-WSP45G-WALTER Item designation: SDMT120425-F57 WSP45G Product type: Fräswendeschneidplatte Manufacturer: Walter Tools Series: Tiger‑tec Gold Facts Insert size: 12 Corner radius: 2.5 mm Relief angle: 15° Thickness code: 04 Tolerance class: M Special features Grade: WSP45G Chipbreaker: F57 Plate form: Square 90° Substrate: coated carbide (PVD) Applicable materials: steel (P), stainless steel (M), superalloys/titanium (S) Execution: T FAQ What materials is this insert suitable for? The SDMT120425‑F57 WSP45G insert is suitable for machining steel, stainless steel and heat‑resistant superalloys/titanium, corresponding to ISO material groups P, M and S. How does the Tiger‑tec Gold coating improve performance? The Tiger‑tec Gold PVD coating on the SDMT120425‑F57 enhances wear resistance and edge stability, which extends tool life and supports consistent chip control during milling. Is the 2.5 mm corner radius suitable for roughing? Yes, the 2.5 mm corner radius on this square insert increases edge strength and is well suited to interrupted cuts and robust roughing strategies. Which chipbreaker is fitted and what is its benefit? This insert features the F57 chipbreaker, designed to promote controlled chip formation and to reduce recutting in a variety of milling conditions. Trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product from the manufacturer; Walter Tools is referenced as the product origin where applicable. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
SDMT1204AZN-D57 WAK15 Wendeplatten - Walter Tools
Benefit from a combination of precise chip control, a sharp uncoated carbide grade and a square 90° geometry for robust milling of aluminium and other non‑ferrous metals; order directly via Metav Werkzeuge or consult our specialists for application-specific cutting data and compatibility advice. SDMT1204AZN-D57 WAK15 milling indexable insert – for aluminium and non‑ferrous metals (Walter Tools) SDMT1204AZN-D57 WAK15 is a square milling insert engineered for efficient machining of aluminium and other non‑ferrous materials, featuring a D57 chipbreaker and a 15° clearance angle. Square 90° geometry for robust milling WAK15 uncoated carbide for aluminium and NE‑metals 15° clearance angle reduces material adhesion D57 chipbreaker for controlled chip formation High‑performance milling for aluminium and non‑ferrous metals The WAK15 grade is an uncoated carbide developed for machining aluminium and similar non‑ferrous alloys; its very sharp cutting edge and low‑friction geometry reduce built‑up edge and material adhesion. The D57 chipbreaker actively fragments chips into short, manageable lengths, improving evacuation and protecting the cutter flutes. The 15° clearance angle lowers friction at the cutting zone, which decreases the tendency for chip welding and supports higher feed rates while preserving surface quality. For manufacturing planners, this means fewer interruptions for chip clearing and more consistent cycle times. Consistent surface finish and process security A square 90° insert form gives robust corner strength and predictable engagement in shoulder and face milling operations, contributing to repeatable component geometry. The tolerance class M and the insert’s stable plate thickness ensure process security and dimensional repeatability when indexing inserts during production. Reduced rework and fewer scrap parts follow from improved edge stability and uniform chip control—advantages that translate directly into higher throughput and lower per‑part machining cost. The insert’s geometry also supports efficient clamping and minimal vibration when mounted in suitable milling cutters. Simple integration, dependable results on the shop floor The SDMT designation places this insert within the Walter N‑series family, compatible with a broad range of cutter bodies configured for square inserts and D‑type chip control. As an indexable solution, the insert allows rapid replacement and reduced tool‑change times compared with brazed cutters, helping to maintain machine uptime. Specification notes such as plate size 12, thickness 04 and the D57 chipbreaker are useful when matching holders and establishing first‑pass cutting parameters. For production engineers seeking to optimise aluminium machining, this insert offers a balance of sharp cutting action and controlled chip formation that supports steady, high‑quality results. Contact Metav Werkzeuge for tailored application support and to discuss Walter Tools SDMT1204AZN-D57 WAK15 insert suitability for specific aluminium alloys — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: SDMT1204AZN-D57-WAK15-WALTER Designation: SDMT1204AZN-D57 WAK15 Product type: Milling indexable insert Brand: Walter Tools Series: Walter N‑Sortensystem Grade: WAK15 Core data Plate size: 12 Thickness: 04 Free angle: 15° Plate form: Quadrat 90° Chipbreaker: D57 Tolerance class: M Execution: T Special features Uncoated carbide (WAK15) Suited for aluminium and non‑ferrous metals Stable chip formation, reduced adhesion Walter N‑series compatibility Square geometry for robust engagement FAQ What materials is this insert intended for? The SDMT1204AZN-D57 WAK15 insert is designed primarily for aluminium and other non‑ferrous metals; the WAK15 uncoated carbide grade and D57 chipbreaker minimise material adhesion and optimise chip control on these alloys. Is the insert coated or uncoated? This insert uses an uncoated carbide grade (WAK15), chosen to provide a very sharp cutting edge and low tendency for built‑up edge when machining soft, sticky materials like aluminium. How does the D57 chipbreaker improve machining? The D57 chipbreaker breaks chips into short segments for reliable evacuation, reducing the risk of entanglement in the cutter flutes and improving surface quality during continuous milling operations. Can this insert be used for shoulder milling and facing operations? Yes; the square 90° geometry offers corner strength suitable for shoulder and face milling, delivering predictable engagement and consistent dimensional results when used with compatible cutter bodies. What does the 15° clearance angle affect in practice? A 15° clearance angle reduces rubbing behind the cutting edge, lowering friction and heat generation; this helps prevent chip adhesion and supports stable cutting when working with aluminium alloys. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names are used here for explanation and identification only; there is no affiliation between our company and the named manufacturers. The offered article is an original, factory‑new product of the manufacturer.
SDMT1204AZN-D57 WKK25G WKK25G Wendeplatten - Walter Tools
Take advantage of the combination of the Tiger·tec Gold WKK25G grade, a 15° relief angle and a square 12 mm format for reliable, high-productivity cast-iron machining. Order the inserts directly via Metav Werkzeuge or ask the consultants for application support. SDMT1204AZN-D57 WKK25G – Indexable milling insert, Tiger·tec Gold, square 12 mm (Walter Tools) The SDMT1204AZN-D57 WKK25G is a square indexable milling insert optimised for cast-iron applications; its Tiger·tec Gold coating and D57 chipbreaker support stable chip formation and consistent edge life. Tiger·tec Gold grade WKK25G Optimised for cast-iron machining 15° relief angle for secure cutting Square 90° format, 12 mm size Consistent edge life through coated carbide technology The combination of the WKK25G coated carbide grade and the Tiger·tec Gold series targets the abrasive wear typical of cast-iron machining. This results in stable chip formation and extended tool life, which reduces downtime for tool changes and increases productive cutting hours. The cutting-material pairing is designed for short, breakable chips common in cast materials, translating into predictable performance and repeatable results in series production. Geometry and dimensions that simplify set-up and precision work The square 90° insert geometry and the 15° relief angle provide a balanced compromise between strength and chip evacuation. The insert size of 12 mm with a thickness corresponding to code 04 ensures rigid clamping and resistance to edge deformation during heavy cuts. These geometric features reduce set-up iterations and help maintain consistent tolerances across batches, supporting efficient process control on milling heads and indexable-cutter systems. Practical chip control and production-oriented features The D57 chipbreaker is engineered for controlled chip splitting and evacuation in cast-iron operations, lowering the risk of built-up edge and machine interruptions. The insert is supplied in tolerance class M, enabling reliable seating and repeatability in toolholders. Designed to integrate into industrial milling workflows, this grade offers a cost-effective balance between wear resistance and cutting reliability for medium to high-volume production runs. Contact Metav Werkzeuge for sample inserts, application data or integration advice on Walter Tools Tiger·tec Gold grades; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: SDMT1204AZN-D57-WKK25G-WALTER Article designation: SDMT1204AZN-D57 WKK25G Manufacturer: Walter Tools Product type: Indexable milling insert Grade/Sort: WKK25G Series: Tiger·tec Gold Core specifications Relief angle: 15° Insert format: Square 90° Size: 12 mm Thickness: 4 mm (code 04) Chipbreaker: D57 Tolerance class: M Design & features Coating: Tiger·tec Gold technology Material: Coated carbide (WKK25G) Execution: T ISO designation: SDMT1204AZN-D57 WKK25G Application suitability: Cast iron (ISO group K) FAQ What materials is this insert best suited to machine? The SDMT1204AZN-D57 WKK25G insert is specifically tuned for cast iron machining; the Tiger·tec Gold coating and WKK25G grade address abrasive wear and short, breaking chips typical of these materials. How does the D57 chipbreaker affect machining performance? The D57 chipbreaker on the SDMT1204AZN-D57 WKK25G promotes controlled chip splitting and evacuation, which improves surface finish consistency and reduces interruptions in cast-iron milling. Can this insert be used for heavy roughing passes? Yes, the square 90° format combined with a 15° relief angle and the robust coated-carbide grade offers strength and edge stability suitable for productive roughing in cast-iron applications. What tolerance and repeatability can be expected when replacing inserts? The insert is supplied in tolerance class M, providing consistent seating and repeatability when exchanging inserts in compatible toolholders for reliable production performance. Manufacturer: Walter Tools; Headquarters: Tübingen, Germany The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is a recognised manufacturer of precision cutting tools and milling solutions. Protected trademarks and product names are the property of their respective owners and are used here for explanatory purposes only. There is no affiliation between our company and the named brands. The offered article is an original, factory-new product of the manufacturer.
SDMT1204AZN-D57 WKP25S Wendeplatten - Walter Tools
Combining the Tiger‑tec Silver coating with the WKP25S carbide grade delivers reliable chip control and extended tool life for steel and cast iron milling; the square 90° geometry and 15° clearance ensure stable cutting and consistent surface quality. Order directly via Metav Werkzeuge or ask our consultants for application advice. SDMT1204AZN-D57 WKP25S milling insert – Tiger‑tec Silver for steel and cast iron (Walter Tools) A SDMT1204AZN-D57 WKP25S indexable milling insert engineered for efficient medium-duty milling of steel and cast iron, featuring a square 90° form and specialised chip control Tiger‑tec Silver coated performance Optimised for steel and cast iron Square 90° geometry for stability Chipbreaker D57 for controlled swarf Consistent productivity through proven coating and grade The combination of the Tiger‑tec Silver technology and the WKP25S cutting grade provides a high level of wear resistance and stable chip formation, which translates into longer tool life and fewer interruptions on the shop floor. Coated carbide substrates balance toughness and hardness to manage the thermal and mechanical loads typical for ISO group P (steel) and K (cast iron). For production environments seeking predictable results, this insert reduces the need for excessive feed adjustments and supports continuous operation. Geometry and clearance that improve stability and surface quality The insert’s square 90° shape, paired with a 15° clearance angle, gives a robust cutting edge and predictable engagement in shoulder and face milling operations. The moderate clearance helps avoid rubbing while maintaining edge strength, so chatter is minimised and surface finishes remain consistent. Tolerance class M and the specified insert size 12 mm with thickness 04 contribute to repeatable tool positioning and interchangeable performance across compatible toolholders. Chip control and application scope for fewer reworks Equipped with chipbreaker D57, this grade is designed to produce short, breakable swarf on interrupted cuts typical for cast components and heavier sections of steel. The chip geometry supports efficient evacuation and reduces heat concentration at the cutting edge, lowering flank wear and preserving the cutting profile. Classified for ISO P and K materials, the insert is suitable for a broad range of steels and cast irons in jobbing and small-batch production while keeping setup complexity low. Practical benefits for process reliability and planning Integrating this insert into milling programmes enables predictable tool-change intervals and simplified tool inventory: the WKP25S grade offers broad applicability across common machining tasks, helping planners consolidate grades and streamline procurement. The robustness of the square geometry reduces toolholder sensitivity, allowing stable feeds and cutting speeds that favour both cycle-time reduction and surface conformity. For workshops aiming to balance economy and quality, the insert supports a reliable baseline for machining strategies. Contact Metav Werkzeuge for availability and tailored milling recommendations — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: SDMT1204AZN-D57-WKP25S-WALTER Designation: SDMT1204AZN-D57 WKP25S Type: Milling insert Manufacturer: Walter Tools Core specifications Clearance angle: 15° Insert size: 12 mm Thickness: 04 Shape: Square 90° Tolerance class: M Chipbreaker: D57 Materials & special features Substrate/coating technology: Tiger‑tec Silver Cutting grade: WKP25S (coated carbide) Suitable for: Steel (P) and Cast iron (K) Series: Tiger‑tec Silver Execution: T FAQ What materials are best machined with this insert? The SDMT1204AZN-D57 WKP25S insert is optimised for steel (ISO group P) and cast iron (ISO group K), reflecting the design focus of the Tiger‑tec Silver grade. How does the chipbreaker D57 affect machining? The D57 chipbreaker produces short, controllable swarf on interrupted and stable cuts, improving evacuation and reducing heat concentration on the cutting edge. Is this insert suitable for finish milling or only roughing? With its square 90° geometry and WKP25S grade, the insert is suited to medium-duty finishing and semi-finishing where stability and consistent surface quality are required. Which toolholders are compatible with a 12 mm insert size? Toolholders specified for the SDMT family and compatible seatings for 12 mm square inserts are appropriate; confirm holder seat dimensions and clamp method for proper fit. How does the Tiger‑tec Silver technology benefit life and performance? Tiger‑tec Silver coating enhances wear resistance and supports stable chip formation, which together extend service life and maintain cutting edge integrity under typical steel and cast iron workloads. Manufacturer: Walter Tools; Walter AG, Tübingen, Germany
SDMT1204AZN-D57 WKP35G Wendeplatten - Walter Tools
The combination of Tiger‑tec Gold wear resistance and the WKP35G grade ensures high process security and long tool life for demanding milling of steel and cast iron; the D57 chipbreaker provides consistent chip formation and surface quality. Order directly via Metav Werkzeuge or consult our application specialists for geometry and clamping recommendations. SDMT1204AZN-D57 WKP35G milling insert — 15° clearance, square 90° — Walter Tools SDMT1204AZN-D57 WKP35G is a coated indexable insert engineered for robust face and shoulder milling in steel and cast iron applications Tiger‑tec Gold coated for long tool life Grade WKP35G for steel and cast iron 15° clearance, square 90° geometry D57 chipbreaker for controlled chips Higher productivity through a wear‑resistant coating The Tiger‑tec Gold coating paired with the WKP35G carbide grade provides a measurable improvement in tool life and process reliability when machining ISO group P (steel) and ISO group K (cast iron). This combination reduces flank and crater wear under elevated cutting temperatures, which in turn extends effective tool life and lowers overall tool cost per component. The coating technology also supports higher cutting speeds where appropriate, enabling greater material removal rates and shorter cycle times while maintaining dimensional stability. Predictable chip control and improved surface finish The chipbreaker D57 is designed to produce short, consistent chips when paired with the square 90° geometry and 15° clearance, improving evacuation and reducing the risk of re-cutting. Controlled chip formation leads to a more repeatable surface quality and decreases the likelihood of tool-induced workpiece damage. In practice, this results in fewer interruptions for chip clearing and reduced secondary finishing work, supporting continuous machining with fewer process deviations. Reduced set‑up time and straightforward indexability Made in the standard SDMT family format with a 12 mm size and thickness 04, the insert uses a common ISO envelope that simplifies stocking and replacement across compatible milling cutters. The square form permits four cutting edges per indexable insert, which maximises usable tool life and reduces downtime for tool changes. The indexable insert design facilitates predictable seating and repeatable positioning in the cutter body, making it suitable for production environments that demand rapid tool changeovers and consistent component quality. Broad material coverage with industrial robustness Certified for machining steel and cast iron according to ISO group designations, the grade provides versatility for mixed production batches or job shops handling varied alloys. The insert’s tolerance class M and execution T ensure stable clamping and geometric repeatability in precision setups. As a Walter Tools product from the Tiger‑tec Gold series, it combines industrially proven substrate and coating technology for reliable performance in medium to heavy milling operations where process security and surface integrity are essential. For process‑critical milling with Walter Tools’ Tiger‑tec Gold grade, contact Metav Werkzeuge for application support and ordering: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: SDMT1204AZN-D57-WKP35G-WALTER Label: Fräswendeschneidplatte SDMT1204AZN-D57 WKP35G Walter Tools Manufacturer: Walter Tools Product type: milling insert Series: Tiger‑tec Gold Facts Insert size: 12 mm Thickness: 04 Clearance angle: 15° Plate form: Square 90° Tolerance class: M Special features Grade: WKP35G (coated carbide) Chipbreaker: D57 Material applicability: steel (P) and cast iron (K) Execution: T WPL designation: SDMT1204AZN-D57 WKP35G Family: Tiger‑tec Gold Story trigger: wendeplatten FAQ What materials is this insert suitable for? This insert is specified for ISO groups P and K, meaning it is suitable for machining steel and cast iron; the WKP35G grade and Tiger‑tec Gold coating are tuned to those material behaviours. How does the D57 chipbreaker affect machining? The chipbreaker D57 produces short, consistent chips and improves evacuation in interrupted or continuous milling, helping to maintain surface quality and reduce rework when using this indexable insert. Can the insert be indexed to use all cutting edges? Yes; the square 90° format allows multiple indexing positions. The SDMT family format and tolerance class M ensure repeatable seating and stable clamping for effective edge utilisation. Is this insert compatible with high‑speed milling? The Tiger‑tec Gold coating enhances thermal resistance and wear control, enabling elevated cutting speeds for many steel and cast iron operations when combined with appropriate feeds and machine capability. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. The mention of brand names such as Walter Tools serves explanatory purposes only and does not indicate any affiliation with Metav Werkzeuge. The offered item is an original, factory‑new product from the manufacturer.
SDMT1204AZN-D57 WPP35G WPP35G Wendeplatten - Walter Tools
Benefit from the Tiger·tec Gold grade and the D57 chipbreaker for consistent chip control and prolonged edge life; the insert’s 15° clearance and square 90° form support stable milling of Stahl components. Order the SDMT1204AZN-D57 WPP35G milling insert via Metav Werkzeuge or request application advice from our consultants. SDMT1204AZN-D57 WPP35G — Milling insert, Tiger·tec Gold, for Stahl SDMT1204AZN-D57 WPP35G is a square milling indexable insert designed for versatile steel machining in industrial milling applications Tiger·tec Gold coating for extended edge life Optimised D57 chipbreaker for steady chips 15° clearance for secure cutting geometry Square 90° form for versatile milling operations High-performance machining for consistent throughput The Tiger·tec Gold coating combined with the WPP35G grade delivers a robust solution for medium to heavy-duty milling of Stahl (ISO P). The coated carbide substrate provides improved wear resistance and thermal stability, which translates into longer tool life and fewer indexings in production. By choosing an insert with a dedicated D57 chipbreaker, shops gain controlled chip formation that reduces interruptions and contributes to a more predictable machining cycle. The result is a measurable improvement in process stability and component repeatability. Precise geometry for secure cutting and surface quality The insert’s Square 90° form and 15° clearance angle combine to give a stable cutting edge that resists deflection under load. This geometry supports accurate dimensioning and helps achieve a consistent surface finish during pocketing and shoulder milling. The insert thickness and edge preparation (SDMT1204AZN-D57) are optimised for rigidity; as a consequence, feed rates can be maintained without sacrificing quality, increasing throughput while retaining tight tolerances in demanding production environments. Versatility across common steel applications Classified for the ISO P group, the WPP35G grade is tuned for the thermal and metallurgical behaviour typical of unalloyed and alloyed Stahl. The balance of toughness and wear resistance makes the insert suitable for a wide range of operations, from roughing to semi-finishing. The coated composition eases control of heat-affected zones at higher cutting speeds, enabling customers to exploit higher productivity without a proportional loss in tool life or surface integrity. Practical integration and handling in the workshop The SDMT-style insert fits standard toolholders for square 90° indexable cutters, simplifying retrofitting into existing tooling systems. Its clear marking (SDMT1204AZN-D57 WPP35G) allows straightforward tool identification and inventory management. Careful selection of cutting parameters in line with Tiger·tec Gold recommendations yields the best balance between cycle time and insert life; technical advisors at Metav Werkzeuge can provide parameter tables and application-specific guidance to match the insert to machining tasks. Contact Metav Werkzeuge for tailored application support and to request the SDMT1204AZN-D57 WPP35G from Walter Tools; technical consultation and order processing are available through Metav Werkzeuge Technical Data SKU: SDMT1204AZN-D57-WPP35G-WALTER Name: SDMT1204AZN-D57 WPP35G Manufacturer: Walter Tools Series: Tiger·tec Gold Facts Free angle: 15° Form: Square 90° Inscribed circle / size: 12 mm Thickness: 4 mm Tolerance class: M Special features Grade: WPP35G Coating: Tiger·tec Gold Substrate: coated carbide Chipbreaker: D57 Application group: Stahl (ISO P) Execution: T FAQ Which materials are best suited for this insert? The SDMT1204AZN-D57 WPP35G insert is optimised for Stahl (ISO P); the WPP35G composition and Tiger·tec Gold coating are tuned for steel machining, offering a balanced wear resistance and toughness. Can this insert be used for both roughing and semi-finishing? Yes; the WPP35G grade provides sufficient toughness for roughing while maintaining the wear resistance required for semi-finishing, making the insert versatile across several milling tasks. What is the benefit of the D57 chipbreaker? The D57 chipbreaker promotes stable chip formation, reducing recutting and improving evacuation; this leads to fewer interruptions and more consistent machining results with the SDMT1204AZN-D57 WPP35G. Is the insert compatible with standard SDMT toolholders? The SDMT geometry of the SDMT1204AZN-D57 WPP35G matches standard toolholders designed for square 90° inserts; correct clamping and alignment ensure optimal performance. How does the Tiger·tec Gold coating affect cutting parameters? Tiger·tec Gold increases thermal resistance and wear performance, allowing operation at higher cutting speeds for improved productivity without a proportional decrease in tool life. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names belong to their respective owners. Brand names are used for explanatory purposes only. There is no connection between our company and the named brands. The offered article is an original factory-new product of the manufacturer.
SDMT1204AZN-D57 WSM35G WSM35G Wendeplatten - Walter Tools
Take advantage of the combination of the Tiger·tec Gold coating and the WSM35G grade for secure chip control and extended edge life when machining stainless steels and high‑temperature alloys; order directly via Metav Werkzeuge or request application advice for optimal cutting parameters. SDMT1204AZN-D57 WSM35G – Milling indexable insert, Tiger·tec Gold coating (Walter Tools) SDMT1204AZN-D57 WSM35G is a square milling insert engineered for stable cutting in rostfreier Stahl and heat‑resistant alloys, offering robust clamping and consistent edge behaviour Tiger·tec Gold coated grade WSM35G Optimised D57 chipformer 90° square insert for robust engagement 15° clearance angle for stable cutting Consistent performance for demanding materials The combination of the WSM35G grade with the Tiger·tec Gold series delivers a pronounced focus on thermal and mechanical resistance. This coated carbide grade is developed to manage the typical challenges of rostfreie Stähle and superalloys: high adhesion tendency, work hardening and elevated cutting temperatures. The result is improved process security and fewer unplanned tool changes, which supports higher productivity in serial and batch production. How the geometry supports reliable machining The 90° square plateform and the specified 15° clearance create a stable engagement with the workpiece and distribute cutting forces across the insert corner. The D57 chipformer promotes controlled chip breakage under varying depths of cut and feeds, reducing the risk of built‑up edge formation and minimising surface irregularities. This geometry is particularly effective when combined with suitable feeds and speeds for the intended material groups. Coating and grade advantages explained The Tiger·tec Gold coating provides a thermal barrier and improved wear resistance under intermittent or continuous heat load, extending cutting edge life. In practice, the coated topology of the grade reduces friction and supports a predictable wear progression, which simplifies tool life planning. The hardened coating system paired with a robust carbide substrate enables secure cutting even where coolant access is limited or where dry machining strategies are preferred. Workshop benefits and process recommendations Using this insert supports more consistent part quality and reduces set‑up frequency thanks to reproducible edge behaviour. The square format offers four indexable corners for cost efficiency, while the coated carbide technology aids repeated operations on difficult‑to‑cut alloys. For best results, pair the insert with toolholders compatible with square 90° geometry and follow supplier guidance on feed per tooth and cutting speed for rostfreie Stähle or S‑group materials. For dependable machining of stainless steel and high‑temperature alloys with Walter Tools’ Tiger·tec Gold inserts, contact Metav Werkzeuge for tailored cutting data and immediate supply: info@metav-werkzeuge.com / +49 2822 7131930 Technical data SKU: SDMT1204AZN-D57-WSM35G-WALTER Article: SDMT1204AZN-D57 WSM35G Type: Milling indexable insert Manufacturer: Walter Tools Series: Tiger·tec Gold Facts Clearance angle: 15° Insert shape: Square 90° Size: 12 Chipformer: D57 Thickness: 04 Tolerance class: M Special features Grade: WSM35G Material suitability: S / M Suitable for: rostfreie Stähle and heat‑resistant superalloys Execution: T FAQ What materials is this insert best suited for? The SDMT1204AZN-D57 WSM35G insert (Walter Tools) is designed primarily for rostfreie Stähle and heat‑resistant superalloys, delivering improved chip control and edge stability. How does the D57 chipformer influence machining? The D57 chipformer promotes controlled chip fragmentation and reliable evacuation, which helps the SDMT1204AZN-D57 WSM35G maintain consistent surface finish and reduce built‑up edge during prolonged cuts. How many cutting edges are available per insert? The square 90° geometry provides four indexable corners per insert, allowing multiple edge changes before replacement of the insert body. Is this insert compatible with high‑feed milling strategies? Yes; the combination of the 15° clearance and the Tiger·tec Gold coating supports moderate to high feed applications on the recommended material groups when paired with suitable toolholders and cutting data. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (marketed as Walter Tools) with headquarters in Tübingen is among the world‑leading manufacturers of precision metal‑cutting tools and is part of the Sandvik group. Protected trademarks and trade names remain the property of their respective owners. Brand names and protected designations are mentioned for explanation only. The offered item is an original, factory‑new product from the manufacturer.
SDMT1204AZN-D57 WSP45G WSP45G Wendeplatten - Walter Tools
High wear resistance and reliable chip control make this insert ideal for demanding milling in steel, stainless steel and heat‑resistant alloys. The Tiger‑tec Gold grade ensures a stable cutting edge and long tool life under elevated thermal loads. Order the SDMT1204AZN-D57 WSP45G directly via Metav Werkzeuge or ask our consultants for tailored application advice. SDMT1204AZN-D57 WSP45G milling insert — square 90°, 15° clearance by Walter Tools The SDMT1204AZN-D57 WSP45G is a square 90° milling insert from the Tiger‑tec Gold range, designed for agile, high‑performance milling across steel, stainless steel and high‑temperature alloys. Tiger‑tec Gold coating technology Suitable for steel, stainless and superalloys Square 90° shape with 15° clearance Consistent chip control D57 geometry Achieve higher productivity with a proven coating and grade The combination of Tiger‑tec Gold coating and the WSP45G grade delivers enhanced wear resistance and dependable cutting‑edge stability. This is particularly beneficial when milling steels and alloys that generate high temperatures and tough chips. The PVD‑based grade supports secure chip formation and reduces the risk of build‑up on the cutting edge, enabling longer uninterrupted machining cycles and fewer insert changes. As a result, machining time and tool consumption are reduced while reproducible surface quality is maintained. Robust geometry that stabilises the machining process A square 90° profile paired with a 15° clearance angle provides a durable cutting edge for moderate to heavy milling cuts. The D57 chipbreaker is tailored to regular, controllable chip segmentation, improving evacuation at higher feeds. The insert’s tolerance class M ensures consistent seating and repeatable cuts, which is essential for process stability in production runs. Engineers benefit from predictable tool performance and easier process parameter setting when switching between jobs or machines. Versatile application range and practical handling Designed for the P/M/S material groups, the insert is suited to unalloyed and alloyed steel, stainless steel and heat‑resistant superalloys including titanium alloys. Its compact insert size and plate thickness provide flexibility for a variety of milling holders and operations. For workshops seeking a universal solution, this insert reduces the need for multiple specialised grades while still delivering targeted performance where thermal and mechanical loads are high. When selecting cutting data, favour slightly reduced depths of cut and controlled feed increases when moving from steel to superalloys to preserve edge life. Contact Metav Werkzeuge for application recommendations on Walter Tools Tiger‑tec Gold inserts, quoting SKU SDMT1204AZN-D57-WSP45G-WALTER; phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: SDMT1204AZN-D57-WSP45G-WALTER Label: Fräswendeschneidplatte SDMT1204AZN-D57 WSP45G Walter Tools Manufacturer: Walter Tools Product type: Fräswendeschneidplatte Series: Tiger‑tec Gold Grade: WSP45G Tolerance class: M Free angle: 15° Shape: Square 90° Size: 12 Chipbreaker: D57 Material applicability: P / M / S Plate thickness: 04 Execution: T ISO designation: SDMT1204AZN-D57 WSP45G UID/SKU: SDMT1204AZN-D57-WSP45G-WALTER Facts Free angle: 15° Insert size: 12 Plate thickness code: 04 Tolerance class: M Special features Tiger‑tec Gold coating technology WSP45G PVD‑coated grade Applicable to steel, stainless steel and superalloys Chipbreaker D57 for consistent chip control Square 90° profile for robust edge life Brand: Walter Tools Series: Tiger‑tec Gold FAQ What materials is this insert suitable for? The SDMT1204AZN-D57 WSP45G from Walter Tools is suitable for the P/M/S groups: steel, stainless steel and heat‑resistant superalloys, offering versatile application across common machining tasks. How does the D57 chipbreaker affect machining? The D57 chipbreaker promotes regular chip segmentation and reliable evacuation, which helps maintain surface finish and reduces the chance of chip‑related interruptions during milling. What benefit does the Tiger‑tec Gold grade provide? Tiger‑tec Gold supplies enhanced wear resistance and thermal stability; the WSP45G grade is tuned for tough cutting conditions, extending tool life and providing consistent edge performance. Is the insert suitable for heavy roughing and finishing? The square 90° geometry and tolerance class M provide a robust edge suited to heavier cuts, while the grade and chipbreaker maintain control for fine finishing passes when parameters are adjusted accordingly. Which designation should be quoted when ordering or specifying tooling? Please use the full ISO designation SDMT1204AZN-D57 WSP45G or SKU SDMT1204AZN-D57-WSP45G-WALTER to ensure the correct insert is supplied. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. Brand names and trademarks are used for explanation only. There is no affiliation between our company and the named manufacturers. The offered article is an original, factory‑new product of the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com