SX-3E300N02-SF5 WSM43G - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the WSM43G grade for stable cutting edges and consistent chip control in difficult-to-machine materials; order or request application advice from Metav Werkzeuge to ensure the right insert for the production task. SX-3E300N02-SF5 WSM43G turning/milling insert by Walter Tools — Tiger·tec Gold coating for high-temperature cutting SX-3E300N02-SF5 WSM43G is an indexable turning and milling insert engineered for demanding materials where heat resistance and edge stability are essential Tiger·tec Gold coating for heat resistance Optimised chip formation and control Suited to rostfreier Stahl and superalloys Stable cutting edge for extended tool life High-temperature performance for consistent machining The Tiger·tec Gold coating combined with the WSM43G grade provides a coated carbide solution optimised for operations that generate high cutting temperatures. The combination reduces thermal wear and supports a stable cutting edge, which translates into longer tool life and fewer interruptions on the shop floor. For processes that demand repeatable performance, the metallurgical design mitigates typical failure modes such as edge chipping and built-up edge formation, enabling more predictable cycle times and reduced rework. Controlled chips and improved surface quality The insert’s chipbreaker, 3E300N02-SF5, is tailored to produce consistent chip forms in materials that tend to form stringy or work-hardened chips. Controlled chip formation reduces heat concentration at the cutting zone and helps maintain coolant and tool clearance, resulting in better surface quality and less manual finishing. For components where dimensional tolerance and finish are critical, this behaviour supports downstream processes and lowers overall scrap rates. Operational benefits that lift productivity Designed as a versatile indexable solution for both turning and face milling operations, the insert offers a balance between edge robustness and cutting capability. The stable geometry and coating reduce tool change frequency, which increases effective machine uptime and boosts productivity per shift. In production environments aiming for consistent throughput, this insert contributes to predictable tool life and fewer interventions from operators, supporting leaner workflows and improved machine utilisation. Practical selection notes and material guidance Selection follows ISO material groups: ISO 513 groups M and S are central here. Group M denotes rostfreier Stahl, materials prone to work hardening and elevated heat at the cutting zone; group S covers heat-resistant superalloys and titanium, which impose extreme thermal and mechanical stresses. The SX-3E300N02-SF5 WSM43G insert is formulated to address these challenges by providing thermal resilience and durable edge geometry. For unfamiliar terms: a chipbreaker channels the removed material into predictable shapes, and a coated carbide grade combines a hard substrate with a protective coating to resist abrasion and thermal softening. Contact Metav Werkzeuge for tailored application advice and supply of Walter Tools Tiger·tec Gold inserts via info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: SX-3E300N02-SF5-WSM43G-WALTER Product type: Drehwendeschneidplatte / Fräswendeschneidplatte Designation: SX-3E300N02-SF5 WSM43G Series: Tiger·tec Gold Grade: WSM43G Manufacturer: Walter Tools Facts ISO material groups: M, S Material application: rostfreier Stahl (M) and heat-resistant superalloys/titanium (S) Chipbreaker code: 3E300N02-SF5 Material designation: coated carbide Special features Coating: Tiger·tec Gold technology Suitable for: rostfreier Stahl and superalloys Optimised for: stable chip formation and edge stability Application: turning and milling indexable operations FAQ What materials is this insert best suited for? The insert is designed for machining materials in ISO groups M and S; it handles rostfreier Stahl and heat‑resistant superalloys or titanium with improved edge life when used within recommended parameters. How does the Tiger·tec Gold coating help in production? The Tiger·tec Gold coating on the WSM43G grade increases wear resistance at elevated temperatures, supporting longer tool life and more consistent cutting behaviour under heavy thermal loads. What role does the 3E300N02-SF5 chipbreaker play? The 3E300N02-SF5 chipbreaker shapes chips into predictable forms, reducing heat concentration and improving surface finish while easing chip evacuation in both turning and face milling. Is this insert suitable for roughing and finishing operations? With its robust grade and coated surface, the insert provides edge stability for roughing in difficult materials and can deliver acceptable finishes depending on the chosen cutting data and toolholder rigidity. Can the insert help reduce downtime in a production setting? Yes; its combination of a stable geometry and a thermally resistant coating reduces the rate of tool wear and unexpected edge failures, contributing to fewer tool changes and higher machine uptime. Walter Tools; Tübingen, Germany; part of the Sandvik Group Protected trademarks and trade names are the property of their respective owners. Mark names and protected product names are mentioned for explanation only. There is no connection between Metav Werkzeuge and the mentioned brands. The offered item is an original, factory-new product of the manufacturer.
SX-3E300N02-SK8 WK1 Wendeplatten - Walter Tools
Take advantage of the combination of a proven uncoated carbide grade and a tailored 3E300N02-SK8 chipbreaker to support consistent material removal and predictable tool life; order or request application advice via Metav Werkzeuge for fast procurement and expert consultation. SX-3E300N02-SK8 WK1 indexable insert for turning and milling — Walter Tools The SX-3E300N02-SK8 WK1 is an indexable insert designed for turning and milling operations, supplied in an uncoated carbide grade and finished with the 3E300N02-SK8 chipbreaker for controlled chip formation. Uncoated carbide grade WK1 3E300N02-SK8 chipbreaker geometry Walter open-series design for versatility For turning and milling applications Improved process stability through consistent chip control The open-series design paired with the 3E300N02-SK8 chipbreaker provides predictable chip formation, which reduces interruptions and rework. Controlled chips decrease the risk of tangling or clogging at the tool edge, which directly supports steady cycle times and contributes to higher production efficiency. For shops aiming to reduce secondary handling, a reliable chip control geometry is a practical advantage. Practical choice of material and what the grade means The insert is supplied in the WK1 grade, an uncoated carbide formulation intended for general-purpose metalcutting; this implies balanced hardness and toughness rather than a surface coating for extra wear resistance. For customers less familiar with carbide grades: uncoated carbide offers a straightforward, predictable performance and is often preferred where thermal or adhesion-sensitive conditions are encountered. Suitability for specific workpiece materials should be checked against the product matrix to ensure optimal selection. Handling, clamping and expected application behaviour As an indexable insert for both turning and milling, the geometry supports flexible tool usage and straightforward indexing when a cutting edge is worn. Correct seat fit and clamping ensure repeatable positioning, which maintains dimensional accuracy and surface finish. In practice, this means fewer tool changes and more uptime when insert seating and clamping torque are correctly applied — a direct contribution to improved throughput and lower production interruptions. Why Walter Tools quality matters in everyday machining Walter Tools’ open-series carbide offerings are known for their consistent manufacturing tolerances and reproducible cutting-edge condition, which helps with process repeatability. Choosing the SX-3E300N02-SK8 WK1 insert brings the benefit of a standardised insert geometry across a range of operations, simplifying tooling inventories and supporting stable machining results across different batches. For shops seeking dependable performance from a recognised brand, the combination of geometry and grade offers a pragmatic balance of robustness and versatility. Contact Metav Werkzeuge for application-specific advice on the SX-3E300N02-SK8 WK1 or to arrange supply through Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: SX-3E300N02-SK8-WK1-WALTER Label: Drehwendeschneidplatte / Fräswendeschneidplatte SX-3E300N02-SK8 WK1 Walter Tools Manufacturer: Walter Tools Product type: indexable insert for turning and milling Facts Series: Walter Schneidstoffsorte - Serie offen Grade: WK1 Chipbreaker: 3E300N02-SK8 Material: catalogue dependent Special features Uncoated carbide (WK1) Designed for turning and milling applications ISO designation: SX-3E300N02-SK8 WK1 Product UID: SX-3E300N02-SK8-WK1-WALTER FAQ What materials is this insert suitable for? The SX-3E300N02-SK8 WK1 is supplied in an uncoated carbide grade; material suitability must be verified in the product matrix to match the WK1 characteristics with the intended workpiece material. Is the chipbreaker suitable for light finishing passes? The 3E300N02-SK8 chipbreaker is designed to produce controlled chips across a range of cutting conditions; its effectiveness in finishing depends on the selected cutting parameters and the specific workpiece material. Can the insert be used in both turning and milling holders? Yes, the insert is a combined turning and milling indexable type; correct seat fit and clamping are essential to achieve the repeatable accuracy expected from this design. How many cutting edges are available before indexing? Cutting-edge count and indexing cycles depend on the insert seat and orientation; consult the toolholder specifications and the insert seating arrangement for exact edge quantities. Where to check detailed machining recommendations for WK1? Machining recommendations and parameter guidance for the WK1 grade are available in the manufacturer’s product matrix and application sheets; refer to these for feed, speed and depth guidance. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trademarks and registered trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes and do not imply any connection between our company and the brand owners. The described article is an original, factory-new product from the manufacturer Walter Tools.
SX-3E300R15-CF5 WSM33G WSM33G Wendeplatten - Walter Tools
Take advantage of the combination of proven wear resistance, reliable chip control and Tiger·tec Gold performance to maintain steady production with fewer interruptions; order directly via Metav Werkzeuge or contact our consultants for tailored machining advice. SX-3E300R15-CF5 WSM33G indexable turning insert — Tiger·tec Gold (Walter Tools) A SX-3E300R15-CF5 WSM33G indexable turning insert designed for demanding turning operations on difficult-to-machine materials, especially rostfreier Stahl and high-temperature superalloys. Tiger·tec Gold coating for high wear resistance WSM33G grade for rostfreier Stahl and superalloys Stable cutting edge and reliable chip control Chipbreaker 3E300R15-CF5 for heavy interrupted cuts Consistent productivity through advanced coating technology The combination of Tiger·tec Gold technology and the WSM33G grade provides a balanced mix of wear resistance and thermal stability that supports longer tool life and predictable performance. This coated carbide formulation has been engineered to manage the thermal loads and adhesion tendencies common with rostfreier Stahl and nickel-based alloys; the result is reduced rework and fewer unplanned tool changes, which translates into measurable improvements in cycle time and process stability. Safer machining and repeatable chip control for heavy-duty turning With the integrated 3E300R15-CF5 chipbreaker and a geometry tuned for secure edge life, this insert ensures stable chip formation even under aggravated cutting conditions. Stable chips and controlled segmentation lower the risk of workpiece surface damage and help maintain consistent dimensional results. The design supports efficient swarf evacuation and reduces the chance of built-up edge, delivering repeatable component quality and easier downstream handling. Practical advantage for mixed-production environments When machining mixed batches that include rostfreier Stahl and heat-resistant alloys, the WSM33G grade offers flexibility without compromising safety margins. The insert’s thermal resilience and edge robustness make it suitable for a variety of turning tasks where unexpected material variation can occur. For workshop planners and process engineers, this means fewer tool variants to stock, simpler setup procedures and improved overall equipment effectiveness. Designed for reliable industrial use and process security Manufactured by a recognised brand in precision tooling, this insert emphasises industrial compatibility and predictable wear behaviour. The proven combination of grade and geometry supports high process security and helps achieve consistent surface finish and dimensional accuracy across production runs. Integration into standard turning tool holders is straightforward, enabling a quick transfer from trial to series production. Contact Metav Werkzeuge today for technical recommendations or to reserve the SX-3E300R15-CF5 WSM33G from stock; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: SX-3E300R15-CF5-WSM33G-WALTER Product: Indexable turning insert SX-3E300R15-CF5 WSM33G Manufacturer: Walter Tools Series: Tiger·tec Gold Grade: WSM33G Chipbreaker: 3E300R15-CF5 Material compatibility: S / M Facts ISO designation: SX-3E300R15-CF5 WSM33G Material code: S / M Application groups (ISO 513): M (rostfreier Stahl), S (superalloys, titanium) Coating technology: Tiger·tec Gold Special features Coated carbide grade optimised for heat and adhesion resistance Suitable for rostfreier Stahl and high-temperature alloys Stable cutting edge for interrupted and continuous cuts Optimised chipformer for secure chip control and evacuation FAQ What materials is this insert suitable for? The SX-3E300R15-CF5 WSM33G from Walter Tools is designed for rostfreier Stahl and heat-resistant superalloys, reflecting the S and M ISO material groups. How does the Tiger·tec Gold technology benefit production? Tiger·tec Gold provides enhanced wear resistance and thermal stability, allowing the insert to maintain a stable cutting edge and extend tool life under demanding turning conditions. Is the chipbreaker suitable for interrupted cuts? Yes, the 3E300R15-CF5 chipbreaker is configured to manage heavy and interrupted cuts while supporting secure chip control and reduced risk of built-up edge. Can this insert be used across different holder systems? The insert’s ISO designation SX-3E300R15-CF5 WSM33G corresponds to standard turning geometries and can be fitted into compatible indexable tool holders designed for this shape and size. What operational benefits can be expected compared with conventional grades? Due to the WSM33G grade and Tiger·tec Gold coating, users can expect longer tool life, improved process security and more consistent surface quality when machining challenging materials. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany, Walter Tools is a brand of Walter AG Walter AG (brand presentation: Walter Tools) is part of the Sandvik group and is recognised for precision metalworking tools. Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only; there is no commercial connection implied between our company and the named brands. The offered article is an original, factory-new product from the manufacturer.
SX-3E300R6-CE4 WKP23G WKP23G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold wear resistance and precise 3E300R6-CE4 chip control to maintain steady cycle times and predictable tool life; order the SX-3E300R6-CE4 WKP23G directly via Metav Werkzeuge or ask our consultants if needed. SX-3E300R6-CE4 WKP23G — Indexable turning insert for steel and cast iron (Walter Tools) SX-3E300R6-CE4 WKP23G is an indexable turning insert designed for demanding turning applications on steel and cast iron, utilising a robust coated-carbide grade from the Tiger·tec Gold family Tiger·tec Gold coating for extended tool life Designed for steel and cast iron machining Coated carbide grade WKP23G for wear resistance Stable chip control with 3E300R6-CE4 geometry Robust wear resistance that extends productive runtime The combination of the Tiger·tec Gold coating and the WKP23G carbide grade delivers a high degree of wear resistance, especially under the thermal and abrasive conditions typical when machining steel and cast iron. The coated-carbide construction reduces flank and crater wear, which translates into longer insert life and fewer tool changes on the shop floor. For production environments where predictable tool life improves planning and reduces downtime, this indexable insert offers a measurable advantage. The design supports stable cutting parameters while maintaining surface quality on the workpiece. Predictable chip control for cleaner turning operations The 3E300R6-CE4 chipformer geometry is engineered to produce reliable chip breaking and evacuation when cutting both unalloyed and alloyed steels as well as cast iron. Consistent chip control reduces the risk of built-up edge and minimises interruptions caused by tangled chips, improving operator safety and eliminating rework. The insert’s geometry is particularly beneficial in medium-to-high depth-of-cut scenarios where chip shape and removal affect cycle times. Clear chips also support automated processes and unattended shifts by lowering the likelihood of machine stops. Stability and process security to boost productivity This grade focuses on process security and repeatability: the coated-carbide chemistry and insert geometry ensure a stable cutting edge and consistent performance batch after batch. In practical terms, shops benefit from fewer tool adjustments and predictable replacement intervals, which together raise overall productivity. The insert is suitable for standard turning operations and supports industrial production demands where consistent surface finish and dimensional accuracy are required. Integration into existing tooling systems is straightforward thanks to the standard insert designation and the familiar clamping form. Contact Metav Werkzeuge today to discuss application parameters for the SX-3E300R6-CE4 WKP23G, request cutting data sheets, or arrange sample trials; eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data Article number: SX-3E300R6-CE4-WKP23G-WALTER Name: SX-3E300R6-CE4 WKP23G Product type: Indexable turning insert Series: Tiger·tec Gold Grade: WKP23G Geometry: 3E300R6-CE4 Manufacturer: Walter Tools Facts No dimensional or cutting-parameter data provided Special features Coating: Tiger·tec Gold (coated carbide) Material suitability: steel (P), cast iron (K) Chipformer: 3E300R6-CE4 Carbide type: coated hardmetal FAQ What materials is this insert suitable for? The SX-3E300R6-CE4 WKP23G is suitable for machining steel (group P) and cast iron (group K) according to its Tiger·tec Gold design. What makes WKP23G different from other grades? WKP23G is a coated-carbide grade optimised for balanced wear resistance and toughness; the grade and Tiger·tec Gold coating together aim to provide consistent tool life in turning applications. Is the 3E300R6-CE4 geometry suitable for automated turning lines? Yes, the 3E300R6-CE4 chipformer is designed for reliable chip breaking and evacuation, which supports automated and unattended machining processes. Can this insert be used for finishing and semi-finishing operations? The insert’s combination of coating and geometry supports both semi-finishing and standard finishing tasks, delivering repeatable surface quality on steel and cast iron. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for identification and explanatory purposes only. There is no affiliation between our company and the manufacturers named. The offered item is an original, factory-new product from the stated manufacturer.
SX-3E300R6-CE4 WSM33G WSM33G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold coating and the WSM33G grade for reliable cutting performance in demanding turning applications, combining stable chip formation with extended tool life; order original Walter Tools inserts directly via Metav Werkzeuge or consult our specialists for tailored machining advice. SX-3E300R6-CE4 WSM33G – Indexable turning insert, Tiger·tec Gold coating by Walter Tools The SX-3E300R6-CE4 WSM33G is an indexable turning insert designed for machining stainless steels and heat‑resistant superalloys, delivering consistent cutting performance in demanding production environments Tiger·tec Gold coated carbide grade WSM33G Optimised for stainless steels and superalloys Stable cutting edge for extended tool life Higher metal removal rates for demanding materials The combination of the Tiger·tec Gold coating and the WSM33G carbide grade provides enhanced resistance to thermal and mechanical wear, enabling increased cutting speeds when machining stainless steels and heat‑resistant alloys. This means a higher metal removal rate without sacrificing edge stability. The coating improves thermal management at the cutting zone, reducing the tendency for built‑up edge and supporting a consistent surface finish. For production shops, this translates into shorter cycle times and fewer tool changes, helping to keep throughput steady under heavy workload. Consistent chip control and process security The 3E300R6‑CE4 chipbreaker geometry is engineered for controlled chip formation; it promotes predictable, small‑breaking chips when turning ductile and work‑hardening materials. Controlled chips reduce the risk of entanglement and machine downtime and facilitate safer part handling downstream. The insert’s geometry, combined with the coated carbide substrate, enhances chip control and contributes directly to long tool life, reducing unplanned interruptions and improving overall process reliability on the shop floor. Practical advantages for workshop efficiency As an indexable turning solution, this insert allows quick index changes and repeatable seating accuracy, supporting lean tool management and predictable production planning. The coated carbide construction yields a robust cutting edge that tolerates thermal fluctuations and elevated contact stresses typical of tough alloys, which in turn minimises rework and scrap. Integration into standard toolholders requires no special modifications, so productivity benefits are realised with minimal setup time. Overall, the insert supports cost‑effective machining by combining durable materials technology with a geometry tailored for demanding applications. Discuss machining requirements with Metav Werkzeuge and specify Walter Tools Tiger·tec Gold inserts for optimal results — contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to request application support or order authentic inserts Technical Data SKU: SX-3E300R6-CE4-WSM33G-WALTER Designation: SX-3E300R6-CE4 WSM33G Product type: Indexable turning insert Series: Tiger‑tec Gold Grade: WSM33G Chipbreaker: 3E300R6‑CE4 Manufacturer: Walter Tools Facts Suitable material groups: M (stainless steels) Suitable material groups: S (heat‑resistant superalloys, titanium) Coating: Tiger·tec Gold Substrate: Coated carbide Special features Optimised for heavy and challenging cuts Stable cutting edge for reduced wear Designed for secure chip formation Direct replacement for standard indexable turning systems FAQ What materials is this insert suitable for? The insert is specified for stainless steels (ISO group M) and for heat‑resistant superalloys and titanium (ISO group S), reflecting the WSM33G grade’s focus on thermal stability and edge retention. How does the Tiger·tec Gold coating improve performance? The Tiger·tec Gold coating reduces friction and improves heat resistance at the cutting edge, which extends tool life and enables higher cutting speeds in demanding turning operations. Is this insert compatible with standard toolholders? Yes, the insert is designed as a direct fit for common indexable turning toolholders using the corresponding insert geometry SX‑3E300R6‑CE4, allowing quick indexing and repeatable seating. Manufacturer / Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
SX-3E300R6-CF5 WSM33G WSM33G Wendeplatten - Walter Tools
Drehwendeschneidplatte SX-3E300R6-CF5 WSM33G für Rostfreien Stahl & Superlegierungen von Walter Tools Die SX-3E300R6-CF5 WSM33G Drehwendeschneidplatte ist eine beschichtete Hartmetallplatte der Serie Tiger·tec Gold und wurde für die produktive Zerspanung von rostfreiem Stahl und hitzebeständigen Superlegierungen entwickelt. Wendeplatte SX-3E300R6-CF5 WSM33G von Walter Tools Tiger·tec Gold-Beschichtung für lange Standzeit Optimierte Spanbildung bei rostfreiem Stahl Stabile Schneidkante für schwere Zerspanung Für hitzebeständige Superlegierungen geeignet Höhere Produktivität durch gezielte Werkstoffzuordnung Die Kombination aus beschichtetem Hartmetall und der Tiger·tec Gold-Technologie sorgt für eine deutlich verbesserte Standzeit und Prozesssicherheit. Die Wendeschneidplatte erlaubt höhere Vorschübe und reduziert Stillstandzeiten, weil die stabile Schneidkante Aufbauschneiden und vorzeitigen Verschleiß minimiert. Daraus resultiert ein direkter Produktivitätsgewinn bei der Bearbeitung schwer zerspanbarer Werkstoffe. Beschichtung und Materialvorteile für anspruchsvolle Einsätze Dank der speziellen Beschichtung bietet die Platte eine verbesserte Wärmebeständigkeit und Kantenstabilität, was besonders bei zähen Werkstoffen relevant ist. Die Sorte WSM33G ist als beschichtetes Hartmetall klassifiziert und wurde für Anwendungen mit hoher thermischer Belastung optimiert. Dadurch entsteht eine konstante Bearbeitungsqualität und eine gleichmäßige Oberflächenbeschaffenheit bei anspruchsvollen Bauteilen. Zielgruppe und typische Einsatzfelder Konzipiert für Fertigungsbetriebe und Lohnbearbeiter, die rostfreie Stähle und hitzebeständige Legierungen bearbeiten, unterstützt diese Wendeschneidplatte stabile Serienläufe und reproduzierbare Ergebnisse. Durch die spezifische Spanformer- und Geometrieauswahl eignet sich die Platte für schwer zugängliche Schnitte und anspruchsvolle Konturen, wodurch Rüstzeiten und Ausschuss reduziert werden. Integration in Fertigungsprozesse und Anwendungshinweise Die Plattengeometrie SX-3E300R6-CF5 bietet eine zuverlässige Spanabfuhr und ist kompatibel mit gängigen Haltersystemen. Bei der Wahl von Schnittdaten wird eine anwendungsorientierte Abstimmung empfohlen, um die Lebensdauer weiter zu maximieren. Für technische Rückfragen und Unterstützung bei der Prozessanpassung steht der Vertrieb zur Verfügung; konstruktive Prozessoptimierung erhöht die Wirtschaftlichkeit spürbar. Empfehlung: Für anspruchsvolle Bearbeitungen von rostfreiem Stahl und Superlegierungen die SX-3E300R6-CF5 WSM33G von Walter Tools über Metav Werkzeuge anfragen oder die technische Beratung unter info@metav-werkzeuge.com / +49 2822 7131930 nutzen Produktmerkmale Artikelnummer: SX-3E300R6-CF5-WSM33G-WALTER Marke: Walter Tools Produktart: Drehwendeschneidplatte Serie: Tiger-tec Gold Sorte: WSM33G Bezeichnung: SX-3E300R6-CF5 Fakten ISO-Werkstoffgruppen: M, S M = rostfreie Stähle S = hitzebeständige Superlegierungen und Titan Besonderheiten Beschichtung: Tiger·tec Gold (beschichtetes Hartmetall) Spanbrecher: 3E300R6-CF5 Materialanwendung: rostfreier Stahl Einsatzgebiet: Schwer zerspanbare Werkstoffe FAQ Welche Werkstoffe bearbeitet die Wendeplatte am besten? Die SX-3E300R6-CF5 WSM33G von Walter Tools ist speziell für rostfreie Stähle (ISO-Gruppe M) und hitzebeständige Superlegierungen (ISO-Gruppe S) ausgelegt und bietet in diesen Bereichen eine gute Spanbildung und Kantenstabilität. Welche Vorteile bringt die Tiger·tec Gold-Beschichtung? Die Tiger·tec Gold-Beschichtung auf der WSM33G-Sorte verbessert die Wärmebeständigkeit und reduziert Verschleiß, was zu längeren Standzeiten und konstanteren Bearbeitungsergebnissen führt. Wie beeinflusst die Plattengeometrie die Zerspanung? Die Geometrie SX-3E300R6-CF5 sorgt für kontrollierte Spanabfuhr und eine robuste Schneidkante, wodurch sich besonders bei schweren Schnitten die Prozesssicherheit erhöht und Rüstaufwand reduziert wird. Ist die Wendeschneidplatte für Serienfertigung geeignet? Ja, die Kombination aus Sorte WSM33G und der Tiger·tec Gold-Serie ist für produktive Serienläufe ausgelegt und unterstützt konstante Qualitätsanforderungen in der Serienfertigung. Worauf sollte bei der Einstellung der Schnittdaten geachtet werden? Die Anpassung von Vorschub und Schnittgeschwindigkeit an Werkstoff und Ausführung der Platte ist entscheidend; für optimale Ergebnisse empfiehlt sich eine processspezifische Abstimmung mit technischer Beratung. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Deutschland Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des Sandvik-Konzerns. Geschützte Markenbezeichnungen dienen nur zu Erläuterungszwecken. Es besteht keine Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SX-3E300R6-CF5 WSM43G WSM43G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and the WSM43G coated‑carbide grade for consistent edge stability and productive machining of stainless steels and heat‑resistant superalloys; order directly via Metav Werkzeuge or ask our consultants for application support. SX-3E300R6-CF5 WSM43G Turning Insert – Tiger‑tec Gold coating, for stainless steels and superalloys (Walter Tools) A SX-3E300R6-CF5 WSM43G indexable turning insert engineered to deliver reliable cutting performance when machining stainless steels and heat‑resistant superalloys in demanding production environments Tiger‑tec Gold coating for heat resistance Optimised chip control for stable cutting Ideal for stainless steel and superalloys Coated carbide grade WSM43G Faster throughput on difficult‑to‑machine materials The combination of coated carbide and Tiger‑tec Gold technology enables higher machining reliability in challenging materials. Designed for the ISO groups M (stainless steels) and S (heat‑resistant superalloys and titanium), the insert supports stable cutting edges and reduced flank wear, which in turn maintains consistent cycle times and fewer tool changes. This results in measurable improvements in productivity and lower process interruptions when turning tough alloys. Coating and grade: why edge stability matters The WSM43G grade is a coated carbide variety optimised for heat resistance and abrasion control. The Tiger‑tec Gold treatment enhances thermal stability at the cutting edge, helping to prevent edge breakdown during continuous or interrupted cuts. For operations that require repeatable performance, the result is a longer tool life and reduced scrap rates, as the cutting edge retains geometry under elevated temperatures and heavy cutting loads. Better chip control and surface quality The 3E300R6‑CF5 chipbreaker geometry promotes efficient chip formation and evacuation, lowering the risk of chip re‑cutting and tool damage. Efficient chip control contributes directly to a superior surface finish and more predictable dimensional results, particularly on stainless steels that tend to form long, stringy chips. The optimised chipformer reduces manual intervention and handling, supporting smoother post‑process operations and improved part quality. Process security and straightforward integration The insert integrates easily into standard indexable toolholders and supports repeatable machining parameters across production batches. The predictable behaviour of this grade under thermal load improves process security, which is essential for series production and tight tolerances. For application counselling or to confirm compatibility with specific workpiece alloys and machine kinematics, technical consultation is available; contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 for tailored recommendations and cutting data. Contact Metav Werkzeuge today for customised cutting data and to request Walter Tools Tiger‑tec Gold inserts for demanding stainless steel and superalloy turning applications Technical data Article number: SX-3E300R6-CF5-WSM43G-WALTER Item: Turning insert SX-3E300R6-CF5 WSM43G Product type: Indexable turning insert Manufacturer: Walter Tools Grade: WSM43G Series: Tiger‑tec Gold Chipbreaker: 3E300R6-CF5 Material group: S / M Facts Applicable material groups: M (stainless steels), S (superalloys/titanium) Suitability indicator: rostfreier Stahl application true Special features Coated carbide grade optimised for heat resistance Tiger‑tec Gold coating for improved edge stability Chipformer 3E300R6‑CF5 for optimised chip control Intended for heavy‑duty and difficult‑to‑machine materials Designed to reduce tool changes and increase process uptime FAQ What materials is this insert best suited for? The SX-3E300R6-CF5 WSM43G insert is primarily intended for stainless steels (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), providing stable cutting performance in those materials. How does the Tiger‑tec Gold coating improve performance? The Tiger‑tec Gold coating enhances thermal resistance at the cutting edge, helping the WSM43G grade to resist wear and maintain edge geometry under elevated cutting temperatures. Which chipbreaker does the insert use and why is it relevant? This insert features the 3E300R6‑CF5 chipbreaker, which promotes reliable chip formation and evacuation, reducing the risk of chip entanglement and improving surface finish. Is the insert suitable for high‑speed turning? The coated‑carbide WSM43G grade and Tiger‑tec Gold coating support productive cutting conditions; suitability for specific high‑speed parameters depends on machine capability and application details—Metav Werkzeuge can provide tailored cutting data. Can this insert be used in standard toolholders? Yes, the SX-3E300R6-CF5 WSM43G indexable insert is compatible with common turning toolholders designed for this ISO shape and size; for verification of fit and recommended cutting parameters consult Metav Werkzeuge. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trade names are mentioned solely for clarification. There is no affiliation between our company and the named brands. The offered article is original factory‑new goods from the manufacturer.
SX-3E310N03-CE4 WSM33G WSM33G Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Gold coating and the WSM33G grade to machine demanding alloys with improved edge stability and controlled chip formation; the dedicated chipformer 3E310N03-CE4 supports predictable chip control and longer tool life. Order directly via Metav Werkzeuge or consult our specialists for application-specific selection. SX-3E310N03-CE4 WSM33G turning and milling indexable insert — Tiger‑tec Gold, coated carbide (Walter Tools) The SX-3E310N03-CE4 WSM33G is an indexable insert engineered for heavy-duty machining of rostfreier Stahl and heat‑resistant superalloys, offering thermal stability and durable cutting edges for production environments Tiger‑tec Gold coated for heat resistance WSM33G grade for rostfreier Stahl and superalloys Chipformer 3E310N03-CE4 for reliable chip control Coated carbide for extended edge life Process reliability in demanding materials The combination of the Tiger‑tec Gold technology and the WSM33G grade delivers a coating system optimised for high temperatures and severe cutting conditions. For components made from rostfreier Stahl or heat‑resistant superalloys, the insert’s coated carbide substrate reduces adhesion and delays build‑up at the cutting edge, which supports a stable cutting edge and consistent part quality. This stability translates into fewer interruptions for regrinding or tool changes and a measurable improvement in process uptime for industrial machining operations. Predictable chip control for uninterrupted production The built‑in chipformer 3E310N03-CE4 is designed to shape and evacuate chips reliably during both roughing and semi‑finishing passes. Controlled chips reduce the risk of recutting, improve surface integrity and lower the chance of workpiece damage, which collectively increase process security on the shop floor. By reducing unexpected stoppages and improving swarf flow, the insert contributes to more predictable cycle times and a smoother production rhythm. Application guidance and selection advantages This indexable insert is aimed at applications where material toughness and heat generation are limiting factors; the grade performs well on rostfreier Stahl and is also suitable for heat‑resistant superalloys and titanium depending on component geometry. As a coated carbide solution, it balances wear resistance with edge robustness, making it a practical choice for mixed production runs and shops seeking repeatable results. For best outcomes, match the insert geometry and cutting parameters to the operation—roughing geometries for heavy stock removal or edge‑protected geometries for extended tool life during semi‑finishing. For tailored application advice on the Tiger‑tec Gold WSM33G grade or to request a technical datasheet, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for swift assistance. Technical data Article number: SX-3E310N03-CE4-WSM33G-WALTER Label: Drehwendeschneidplatte / Fräswendeschneidplatte SX-3E310N03-CE4 WSM33G Walter Tools Product type: Turning and milling indexable insert Series: Tiger‑tec Gold Grade: WSM33G Manufacturer: Walter Tools Facts Material groups: S / M Chipformer: 3E310N03-CE4 ISO designation: SX-3E310N03-CE4 WSM33G SKU: SX-3E310N03-CE4-WSM33G-WALTER Special features Coated carbide (beschichtetes Hartmetall) Optimised for rostfreier Stahl and heat‑resistant superalloys Designed for stable edge life and secure chip formation Suitable for heavy‑duty machining scenarios FAQ Which materials can this insert machine effectively? The SX-3E310N03-CE4 WSM33G is formulated for rostfreier Stahl (stainless steels) and heat‑resistant superalloys; its coating and substrate improve performance where heat and toughness are critical. What advantage does the Tiger‑tec Gold technology provide? Tiger‑tec Gold increases thermal resistance and wear protection on the insert, which supports longer edge life and more consistent dimensional results under elevated cutting temperatures. How does the chipformer 3E310N03-CE4 affect productivity? The chipformer 3E310N03-CE4 shapes chips to reduce clogging and recutting, improving swarf evacuation and thus supporting uninterrupted cycles and better surface quality. Is this insert suitable for finishing operations? Depending on the selected geometry, the grade can be used for medium finishing; its strength lies in maintaining edge integrity under difficult cutting conditions, which aids repeatable finishes. Can the same grade be used for titanium or nickel‑base alloys? WSM33G is designed for heat‑resistant superalloys (ISO group S) as well as rostfreier Stahl (ISO group M); performance on titanium or nickel‑base materials will depend on cutting parameters and tool geometry. Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation only and do not indicate any affiliation between our company and the named brands. The offered item is an original, factory‑new product from Walter Tools. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
SX-3E310N03-CE4 WSM43G WSM43G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the WSM43G grade for secure chip formation and extended tool life; ideal for machining stainless steel and heat‑resistant superalloys. Order the insert via Metav Werkzeuge or consult our specialists for application-specific recommendations. SX-3E310N03-CE4 WSM43G – Indexable Insert for Turning and Milling, Tiger·tec Gold (Walter Tools) The SX-3E310N03-CE4 WSM43G is a coated carbide indexable insert engineered for heavy‑duty machining of stainless steel and heat‑resistant superalloys in demanding industrial environments Tiger·tec Gold coated carbide grade WSM43G Optimised for stainless steel and superalloys Stable cutting edge for high‑temperature work Improved process stability through heat‑resistant coating The Tiger·tec Gold technology provides a coated carbide surface that is designed to withstand elevated temperatures and abrasive conditions commonly encountered when machining stainless steel and nickel‑based alloys. By combining a thermally stable coating with a robust substrate, this insert supports consistent results and reduced risk of built‑up edge. For production planners, this translates into fewer interruptions and more predictable cycle times; the technology reduces the frequency of insert changes and helps to maintain dimensional accuracy over longer tool life spans. The result is a measurable uplift in process reliability and a lower total cost of machining through sustained performance. Reliable chip control and cutting edge behaviour The insert geometry identified by the designation 3E310N03‑CE4 is optimised for chip control under the strain of tough materials. Controlled chip formation is critical for uninterrupted machining, safe swarf evacuation and surface integrity. The WSM43G grade is developed to support a stable cutting edge when cutting materials that conduct heat poorly and impose heavy thermal loads on the tool. In practice, this means improved surface finish and a reduced tendency for spontaneous edge failure, which benefits job shops and production lines aiming for repeatable quality in series production. Practical advantages on the shop floor and selection guidance Selection of the SX‑3E310N03‑CE4 WSM43G insert should be driven by the workpiece material and the required machining strategy: the grade is especially suited to stainless steel (ISO group M) and to heat‑resistant alloys and titanium (ISO group S). For teams less familiar with these classifications, M denotes stainless steel, which often demands special attention to heat generation and chip formation, while S denotes superalloys and titanium, which stress the cutting edge thermally and mechanically. Choosing this insert supports higher process security, fewer reworks and better predictability in component quality, which cumulatively improve throughput and customer confidence. Contact Metav Werkzeuge for tailored advice on the SX-3E310N03-CE4 WSM43G and reach our specialists at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: SX-3E310N03-CE4-WSM43G-WALTER Product type: Drehwendeschneidplatte / Fräswendeschneidplatte Brand: Walter Tools Facts Series: Tiger·tec Gold Grade: WSM43G ISO designation: SX-3E310N03-CE4 WSM43G Special features Coated carbide Suitable for stainless steel (M) and superalloys/titanium (S) Stable cutting edge and optimised chip control FAQ Which materials can be machined with this insert? The SX-3E310N03-CE4 WSM43G is specified for stainless steel (ISO group M) and for heat‑resistant superalloys and titanium (ISO group S), providing robust performance under high thermal loads. How does the Tiger·tec Gold coating improve performance? The Tiger·tec Gold coating enhances thermal resistance and wear protection on the insert, which supports sustained cutting edge integrity and improved tool life when machining demanding materials. What benefits does the WSM43G grade deliver in production? WSM43G offers stable chip formation and a reliable cutting edge, contributing to fewer tool changes, more consistent part quality and improved process security in serial machining. Is this insert suitable for high‑speed finishing operations? Depending on the machine setup and cutting parameters, the coated carbide grade is designed to handle elevated temperatures; geometry and parameter selection should be matched to the finishing application for optimal surface quality. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered article is an original, factory‑new product from the manufacturer (Walter Tools).
SX-3E310N03-CF5 WSM33G WSM33G Wendeplatten - Walter Tools
Take advantage of the combination of durable Tiger·tec Gold coating and the WSM33G grade for stable, long-lasting performance in demanding machining; order directly via Metav Werkzeuge or consult their specialists for application-specific recommendations. SX-3E310N03-CF5 WSM33G Turning/Milling Indexable Insert — Tiger·tec Gold, for rostfreier Stahl and superalloys (Walter Tools) SX-3E310N03-CF5 WSM33G is a coated carbide indexable insert engineered for heavy-duty turning and milling of rostfreier Stahl and heat-resistant superalloys, offering reliable chip control and thermal stability in demanding production environments. Tiger·tec Gold coating for thermal resilience Stable cutting edge, optimised chip control Suitable for rostfreier Stahl and superalloys High performance on hard-to-machine materials The combination of the WSM33G grade and Tiger·tec Gold coating provides a pronounced advantage when machining materials that build up heat and work-harden, such as rostfreier Stahl and nickel-based alloys. The coated carbide construction improves wear resistance and reduces flank wear, which translates into fewer tool changes and higher throughput. In practical terms, this means more predictable cycle times and enhanced process stability when facing elevated cutting temperatures or abrasive conditions. The insert’s design aims to deliver consistent dimensional results in continuous and interrupted cuts. Reliable chip formation and cutting-edge stability The geometry code 3E310N03-CF5 denotes an integrated chipbreaker and edge preparation designed to secure chip control and reduce the occurrence of built-up edge. Stable chip control improves surface finish and lowers the risk of tool-induced damage to workpiece surfaces, particularly in stainless materials that tend to adhere to cutting edges. The robust cutting edge ensures repeatable performance across long production runs, supporting sustained metal removal rates without sacrificing component quality. For operations prioritising uptime, the balance between edge strength and chip evacuation offers measurable productivity gains. Practical benefits for workshop and production use As a versatile indexable insert, this solution supports both finishing and light to medium roughing tasks depending on the chosen cutting data and assembly. The coated carbide substrate and Tiger·tec Gold technology provide a favourable wear profile, reducing the frequency of insert changes and contributing to predictable tooling costs over time. Compatibility with ISO groups M and S confirms suitability for rostfreier Stahl (M) as well as heat-resistant superalloys and titanium alloys (S), making the insert a strong choice for job shops and production facilities handling mixed or specialised materials. The result is improved process reliability and a lower total cost of ownership. Contact Metav Werkzeuge for tailored cutting data and rapid supply of Walter Tools inserts; their specialists will advise on optimal parameters for Tiger·tec Gold grades and delivery options via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: SX-3E310N03-CF5-WSM33G-WALTER Label: Drehwendeschneidplatte / Fräswendeschneidplatte SX-3E310N03-CF5 WSM33G Walter Tools Product type: Turning/milling indexable insert Manufacturer: Walter Tools Series: Tiger·tec Gold Grade: WSM33G Geometry: 3E310N03-CF5 Material: coated carbide (beschichtetes Hartmetall) UID: SX-3E310N03-CF5-WSM33G-WALTER Facts Geometry code: 3E310N03-CF5 Grade identification: WSM33G Coating technology: Tiger·tec Gold Intended material groups: M, S SKU/UID present Special features Suitable for rostfreier Stahl (ISO M) Suitable for superalloys and titanium (ISO S) Optimised chipformer for secure chip control Stable cutting edge for extended tool life Coated carbide construction for wear resistance FAQ Which materials are suitable for this insert? The SX-3E310N03-CF5 WSM33G insert from Walter Tools is designed for rostfreier Stahl (ISO M) and heat-resistant superalloys/titanium (ISO S), providing heat resistance and stable cutting edges for these challenging materials. What benefits does the Tiger·tec Gold coating provide? Tiger·tec Gold on the WSM33G grade enhances thermal stability and wear resistance for coated carbide inserts, improving tool life and process reliability during high-temperature machining of rostfreier Stahl and superalloys. How does the geometry 3E310N03-CF5 influence machining? The 3E310N03-CF5 geometry includes a dedicated chipbreaker and edge preparation that promote consistent chip control and reduced built-up edge, leading to better surface quality and fewer interruptions in production when using this insert. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no connection between our company and the mentioned brands. The offered item is an original, factory-new product of the manufacturer.
SX-4E400L6-CE4 WSM33G WSM33G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating performance, the wear-resistant WSM33G grade and reliable chip control for efficient machining of stainless steels and difficult-to-machine alloys; order directly via Metav Werkzeuge or consult the team for application advice. SX-4E400L6-CE4 WSM33G Turning indexable insert – optimised for stainless steels and superalloys | Walter Tools The SX-4E400L6-CE4 WSM33G is an indexable turning insert from the Tiger·tec Gold range, designed for heavy-duty machining of stainless steels and heat-resistant superalloys, offering robust edge stability and reliable chip formation. Tiger·tec Gold coating technology Optimised for stainless steel and superalloys Coated carbide grade WSM33G Stable cutting edge and reliable chip control Maximise process reliability with a coating engineered for heat and adhesion resistance The Tiger·tec Gold coating delivers a combination of hardness and toughness that reduces the tendency for built-up edge when machining stainless steels and other adhesive alloys. As a coated carbide grade, WSM33G balances wear resistance with fracture toughness, which means longer tool life and fewer interruptions for insert changes. This results in a more consistent surface finish and reduced rework in demanding turning operations. Secure chip control that protects the tool and workpiece The integrated chipbreaker geometry (4E400L6-CE4) promotes predictable chip formation even under high thermal load. Controlled chips lower the risk of workpiece damage and reduce machining cycle variability. For production environments where repeatability matters, the combination of geometry and stable cutting edge ensures safer swarf evacuation, easier handling and fewer machine stoppages. Application-focused grade for difficult-to-machine materials The insert grade is tailored for the ISO groups M and S, making it suitable for rostfreier Stahl (stainless steel) and heat-resistant superalloys or titanium alloys depending on the tool geometry. In practice, this means the insert supports secure chip formation where thermal conductivity is low and cutting temperatures are high, helping to maintain dimensional accuracy and surface integrity on critical components. Practical benefits for shop-floor productivity Using this indexable insert reduces downtime through extended edge life and consistent performance, contributing to higher productivity per shift. The coated hardmetal composition and the Tiger·tec Gold technology enable stable machining across a broad material spectrum, simplifying tooling decisions and lowering the number of changeovers required for mixed-material batches. Contact Metav Werkzeuge for tailored recommendations on clamping, cutting parameters and availability of Walter Tools Tiger·tec Gold inserts Technical Data SKU: SX-4E400L6-CE4-WSM33G-WALTER Article designation: SX-4E400L6-CE4 WSM33G Product type: Turning indexable insert Series: Tiger·tec Gold Grade: WSM33G Manufacturer: Walter Tools Facts Material suitability: S / M Chipbreaker designation: 4E400L6-CE4 ISO application groups: M (stainless steels), S (superalloys/titanium) Coating: Tiger·tec Gold Special features Coated carbide grade for improved wear resistance Optimised geometry for reliable chip control Designed for heavy-duty and adhesive materials Stable cutting edge for reduced edge breakdown FAQ Which materials are suitable for this insert? The SX-4E400L6-CE4 WSM33G insert is suitable for stainless steels (ISO group M) and for heat-resistant superalloys or titanium (ISO group S), depending on the insert geometry. What benefits does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating on the WSM33G grade improves wear resistance and reduces built-up edge, extending insert life during machining of adhesive and high-temperature alloys. Is this insert appropriate for high-temperature alloys used in aerospace? Yes, the combination of the WSM33G grade and the 4E400L6-CE4 chipbreaker makes the insert a good choice for many heat-resistant superalloys encountered in aerospace component turning. How does the chipbreaker affect machining stability? The 4E400L6-CE4 chipbreaker promotes repeatable chip formation and evacuation, which enhances machining stability and protects the cutting edge during continuous turning operations. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered item is original, factory-new goods from the manufacturer.
SX-4E400L6-CF5 WSM33G WSM33G Wendeplatten - Walter Tools
Combine high wear resistance and Tiger‑tec Gold coating with the WSM33G grade for reliable machining of stainless steels and heat‑resistant superalloys; order genuine Walter Tools inserts through Metav Werkzeuge or consult our technical advisors for application-specific recommendations SX-4E400L6-CF5 WSM33G indexable turning insert – Tiger‑tec Gold, Walter Tools SX-4E400L6-CF5 WSM33G is an indexable turning insert optimised for machining stainless steels and heat‑resistant superalloys, offering a coated carbide grade for stable chip formation and long tool life Tiger‑tec Gold coating for heat resistance and wear control Optimised WSM33G grade for stable cutting edges Chipbreaker 4E400L6‑CF5 for reliable chip control Suited to stainless steels (M) and superalloys (S) Increased productivity on hard‑to‑cut materials The combination of the Tiger‑tec Gold coating and the WSM33G coated carbide grade delivers measurable gains in process reliability when turning demanding materials. The coating improves heat resistance at the cutting edge while the grade balances toughness and hardness to resist chipping; together they reduce unscheduled tool changes and contribute to steady productivity. For machinists this means fewer interruptions during long cycles and a predictable tool life, especially when tackling stainless steels and heat‑resistant superalloys that tend to work‑harden and generate high cutting temperatures. The insert designation 4E400L6‑CF5 denotes the chipbreaker geometry designed to support controlled chip formation in such alloys. Better surface quality and longer edge life A core advantage of the Tiger‑tec Gold technology is improved edge stability, which directly affects surface finish and dimensional consistency. The coated carbide substrate offers wear protection against abrasion and thermal load; this reduces built‑up edge and prevents premature flank wear. As a result, component faces show fewer irregularities and a reduced need for downstream finishing. Explaining the technical term: a coated carbide insert carries a thin, engineered layer that delays wear mechanisms—this preserves the cutting geometry and leads to longer intervals between re‑grinds or insert changes, lowering overall machining costs and raising first‑pass yield. Practical application and process guidance The insert is intended for conventional turning operations where chip control and edge robustness are essential. The 4E400L6‑CF5 chipbreaker provides a consistent chip form that eases evacuation and reduces entanglement, which is particularly useful on long continuous cuts or interrupted surfaces. Material compatibility is indicated by the ISO groups M (stainless steels) and S (heat‑resistant alloys and titanium); selecting appropriate cutting speeds, feeds and coolant strategies will further extend service life. For holder compatibility, standard indexable turning tool systems that accept this insert designation will be suitable; consult technical data sheets for seat geometry and clamp type. Combining the right insert geometry with stable workholding and optimised cutting data yields the most reliable outcomes. Discuss machining strategies and source genuine Walter Tools SX-4E400L6-CF5 WSM33G inserts from Metav Werkzeuge — contact our technical team for tailored recommendations and application support Technical Data Article number/SKU: SX-4E400L6-CF5-WSM33G-WALTER Product type: indexable turning insert (Drehwendeschneidplatte) Manufacturer: Walter Tools Facts Grade: WSM33G Series: Tiger‑tec Gold Chipbreaker: 4E400L6‑CF5 Applicable material groups: M, S Special features Coating: Tiger‑tec Gold (coated carbide) Material applicability: stainless steels (M) Material applicability: heat‑resistant superalloys / titanium (S) Designed for stable chip formation and edge life FAQ Which materials are best suited for this insert? The SX-4E400L6-CF5 WSM33G insert is intended for stainless steels (ISO group M) and heat‑resistant superalloys (ISO group S); the WSM33G grade and Tiger‑tec Gold coating help manage heat and maintain edge stability in these materials. What does the chipbreaker code 4E400L6‑CF5 indicate? The code identifies the chipbreaker geometry and rake characteristics; 4E400L6‑CF5 is engineered to produce a controllable chip form and assist evacuation during turning of tough alloys, improving process security. How does the Tiger‑tec Gold coating improve performance? Tiger‑tec Gold provides enhanced thermal resistance and wear protection for the coated carbide substrate, which contributes to longer tool life, reduced built‑up edge and more consistent surface quality during extended cuts. Can this insert be used for interrupted cuts or roughing? Yes; the combination of the WSM33G grade and robust chipbreaker makes the insert suitable for heavier cuts and intermittent engagement, provided appropriate machine rigidity and clamping are ensured. Are genuine Walter Tools inserts supplied via Metav Werkzeuge? Genuine Walter Tools inserts such as the SX-4E400L6-CF5 WSM33G are available through Metav Werkzeuge; consult their technical advisors for holder compatibility and machining parameter recommendations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation only; there is no affiliation between our company and the referenced manufacturers. The offered item is an original, factory‑new product of the named manufacturer (Walter Tools).
SX-4E400N02-CE4 WKP23G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, the WKP23G grade and a proven chipbreaker geometry to achieve reliable performance when machining steel and cast iron; order directly via Metav Werkzeuge or consult our specialists for tailored recommendations. Turning/milling indexable insert SX-4E400N02-CE4 WKP23G — Tiger·tec Gold by Walter Tools A SX-4E400N02-CE4 WKP23G indexable insert designed for productive turning and milling of steel and cast iron in industrial machining applications. Tiger·tec Gold coating for long tool life Optimised for steel and cast iron machining Stable cutting edge for consistent finishes Suitable for turning and milling operations Engineered for predictable productivity The insert belongs to the Tiger·tec Gold series and the WKP23G cutting grade, a combination engineered for extended service life and consistent performance in demanding production environments. The coating technology reduces abrasive wear and supports stable edge retention, which lowers the frequency of tool changes and thus contributes to improved process economy. Optimisation for the ISO groups P (steel) and K (cast iron) ensures that chip formation and thermal behaviour are addressed specifically for these materials, enabling reliable machining across a wide range of common workpiece steels and cast irons. Controlled chip formation and surface quality Thanks to the specified chipbreaker geometry 4E400N02-CE4, the insert promotes controlled chip flow and repeatable cutting behaviour in both turning and milling setups. This geometry assists in avoiding long, stringy chips and supports consistent material removal, which in turn improves surface quality and reduces rework. For workshop teams seeking reproducible finishes and dimensional stability, the indexable insert offers a practical route to minimise scrap and increase first-pass yield without complex process changes. Fewer interruptions, higher efficiency By combining a robust grade with an optimised geometry, the insert supports uninterrupted production runs and predictable tool life, which are key to lowering unit costs in batch and continuous machining. The proven behaviour of the tiger·tec coating technology reduces the risk of premature edge breakdown under typical steel and cast iron conditions. Integrating this cutting solution into existing toolholders is straightforward, so line managers can expect a rapid return in uptime and throughput while maintaining consistent part quality. Choosing the right variant and application notes Selection should consider the specific steel grade or cast iron type and the operation—whether roughing or finishing—since machining parameters and desired surface finish affect grade suitability. The SX-4E400N02-CE4 insert fits applications where controlled chips and stable edges are priority; the WKP23G grade is focused on a balance of wear resistance and edge robustness. For precise recommendations on feed, speed and clamping options, Metav Werkzeuge’s advisers can provide geometry-matched guidance to achieve optimal cycle times and minimal tool costs. For production-critical turning and milling, specify the Walter Tools Tiger·tec Gold SX-4E400N02-CE4 WKP23G insert and contact Metav Werkzeuge for application-specific advice and availability at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: SX-4E400N02-CE4-WKP23G-WALTER Label: Drehwendeschneidplatte / Fräswendeschneidplatte SX-4E400N02-CE4 WKP23G Walter Tools Product type: Drehwendeschneidplatte / Fräswendeschneidplatte Manufacturer: Walter Tools ISO designation: SX-4E400N02-CE4 WKP23G Facts Grade/series: Tiger·tec Gold Sort: WKP23G Chipbreaker: 4E400N02-CE4 Material application: P / K (steel / cast iron) SKU: SX-4E400N02-CE4-WKP23G-WALTER Special features Coated carbide cutting grade Designed for turning and milling Optimised chip control and edge stability Suitable for industrial production environments FAQ What materials can this insert machine effectively? The SX-4E400N02-CE4 WKP23G insert is optimised for P (steel) and K (cast iron) applications and delivers reliable chip control and wear resistance when used on these material groups. How does the Tiger·tec Gold series improve performance? The Tiger·tec Gold coating reduces abrasive wear and enhances edge stability, which results in longer tool life and more consistent machining behaviour for the WKP23G grade. Is this insert suitable for both turning and milling? Yes, the insert is specified for turning and milling operations; the chipbreaker 4E400N02-CE4 promotes controlled chip formation across both process types. How should cutting data be adapted for different steels? Cutting speeds and feeds should be adjusted according to the specific steel grade and operation; the WKP23G grade provides a robust starting point, and fine-tuning is recommended for optimal surface finish and tool life. Can this insert reduce downtime in production? By offering stable edge retention and controlled chip flow, the insert helps decrease the frequency of tool changes and can contribute to higher machine utilisation and fewer interruptions. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany; info@walter-tools.com Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only. There is no affiliation between our company and the mentioned brands. The offered article is an original, factory-new product of the manufacturer.
SX-4E400N02-CE4 WKP23S Wendeplatten - Walter Tools
Benefit from a combination of high process reliability and extended tool life thanks to the Tiger·tec Silver coating and the WKP23S carbide grade; this ensures consistent productivity when machining steel and cast iron. Order directly via Metav Werkzeuge or consult the Metav team for application-specific recommendations. Turning and Milling Indexable Insert SX-4E400N02-CE4 WKP23S for Steel and Cast Iron – Walter Tools The SX-4E400N02-CE4 WKP23S is a coated indexable insert designed for productive turning and milling tasks on steel and cast iron, offering reliable wear resistance and consistent chip formation. *Tiger·tec Silver coated carbide grade *Optimised chip control geometry *Suitable for ISO P and ISO K materials *Stable cutting edge for high productivity Maximise uptime with a wear-resistant coated grade The Tiger·tec Silver technology delivers a coated carbide solution that balances toughness and hardness, reducing abrasive and adhesive wear in mixed cutting conditions. The WKP23S grade is optimised for the thermal and mechanical demands of machining both steel and cast iron, which helps to maintain a stable cutting edge over longer cycles. For production environments where repeatability matters, this combination reduces tool changes and contributes to predictable process windows, allowing planners to schedule more consistent throughput. Consistent chip control across turning and milling operations The insert’s geometry, identified by the chipbreaker 4E400N02-CE4, supports controlled chip formation for a range of depths of cut and feeds. Good chip control lowers the risk of built-up edge and surface defects, improving surface finish and reducing rework. Compatibility with the ISO P and ISO K material groups means the insert handles both ductile and brittle chip behaviours, making it suitable for versatile machining cells where the same tooling must perform on multiple components. Increase productivity through process security and clarity As an indexable insert for turning and milling, the component offers predictable edge life and straightforward indexation, which simplifies tool management on the shop floor. The robust geometry and coating combination improve productivity by enabling higher stable cutting parameters and by giving operators clearer wear indications. When integrated into a controlled machining strategy, the insert supports shorter cycle times and contributes to overall equipment effectiveness without compromising surface quality. For robust steel and cast iron machining, request application advice from Metav Werkzeuge and specify the SX-4E400N02-CE4 WKP23S insert by Walter Tools to secure stable production results — contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930. Technical Data Article number: SX-4E400N02-CE4-WKP23S-WALTER Description: Drehwendeschneidplatte / Fräswendeschneidplatte SX-4E400N02-CE4 WKP23S Walter Tools Series: Tiger-tec Silver Grade: WKP23S Material groups: P / K Manufacturer: Walter Tools Facts Geometry code: 4E400N02-CE4 ISO groups: P, K Product type: Turning and milling indexable insert Designation: SX-4E400N02-CE4 WKP23S Special features Coated carbide grade WKP23S Application: Steel and cast iron machining Stable cutting edge and optimised chip control Suitable for productive turning and face milling FAQ What materials is this insert suitable for? The SX-4E400N02-CE4 WKP23S insert is designed for machining steel (ISO P) and cast iron (ISO K), delivering reliable wear behaviour in both groups. What does the Tiger·tec Silver coating provide? Tiger·tec Silver offers a balance of hardness and toughness; the coating on the WKP23S grade improves resistance to abrasion and edge degradation, extending the effective tool life of the insert. How does the 4E400N02-CE4 chipbreaker affect machining? The 4E400N02-CE4 chipbreaker ensures controlled chip formation across a wide range of feeds and depths, which enhances surface quality and reduces the risk of built-up edge during turning and milling. Can the insert be used for both turning and milling in the same tool system? Yes, the SX-4E400N02-CE4 WKP23S is specified as a combined turning and milling indexable insert and is suitable for operations where tooling versatility is required. What operational benefit does the WKP23S grade bring to production? WKP23S provides consistent cutting performance and predictable wear, supporting higher productivity and fewer unscheduled tool changes. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand appearance: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only and do not imply any association between our company and the manufacturers. The offered item is an original, brand-new product from the manufacturer.
SX-4E400N02-CE4 WSM23G WSM23G Wendeplatten - Walter Tools
Take advantage of the WSM23G grade and Tiger‑tec Gold coating for consistent edge stability and improved tool life when machining demanding alloys; order the insert directly via Metav Werkzeuge or consult the team for application support. SX-4E400N02-CE4 WSM23G — Indexable turning/milling insert by Walter Tools (Tiger‑tec Gold coating, chipbreaker 4E400N02-CE4) SX-4E400N02-CE4 WSM23G is an indexable turning/milling insert designed for heavy-duty machining of rostfreier Stahl and heat‑resistant superalloys and titanium, offering a robust coated‑carbide grade for demanding production environments Tiger‑tec Gold coating for edge stability Grade WSM23G for tough materials Optimised chip formation for reliable machining Suitable for rostfreier Stahl and superalloys Longer tool life thanks to premium coating and grade The combination of the Tiger‑tec Gold coating with the WSM23G grade delivers a coating‑enhanced coated carbide substrate that resists abrasive and thermal wear. This formulation supports a stable cutting edge at elevated temperatures, reducing the frequency of tool changes and downtime. For production shops processing rostfreier Stahl or high‑temperature alloys, the result is a measurable improvement in component throughput and reduced tooling costs per part. The design also helps prevent built‑up edge on reactive materials, keeping surface finishes consistent over longer tool life. Reliable chip control and process security for demanding materials The integrated chipbreaker 4E400N02-CE4 provides controlled chip formation, which is critical when machining materials from ISO groups M and S: rostfreie Stähle and heat‑resistant superalloys/titanium. Stable chips reduce the risk of workpiece damage and enable safer, faster feeds. From a machining‑process perspective, improved chip control enhances repeatability and lowers the chance of interruptions caused by chip entanglement. Where cycle time and process stability matter, this insert contributes to predictable production and easier process documentation. Production benefits: consistent surface quality and efficient operation As an indexable insert engineered for both turning and milling applications, the geometry balances edge strength and cutting economy. The WSM23G grade was selected to handle the combination of toughness and heat encountered when cutting rostfreier Stahl and high‑alloy materials, so operators can achieve consistent part tolerances and surface appearance. Fewer tool changes and reliable edge behaviour translate directly into increased machine uptime and lower unit costs, making the insert a practical choice for job shops and volume manufacturers alike. Contact Metav Werkzeuge for tailored application advice and to secure the Walter Tools SX-4E400N02-CE4 WSM23G insert — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 for specification matching and availability Technical data Article number: SX-4E400N02-CE4-WSM23G-WALTER Product: Drehwendeschneidplatte / Fräswendeschneidplatte ISO designation: SX-4E400N02-CE4 WSM23G Manufacturer: Walter Tools Facts Material group: S / M Series: Tiger‑tec Gold Chipbreaker: 4E400N02-CE4 Grade: WSM23G Special features Coating: coated carbide (Tiger·tec Gold) Suitable for: rostfreier Stahl; heat‑resistant superalloys and titanium Application: turning and milling insert Stable chip formation; optimised cutting edge FAQ What materials is this insert designed for? The SX-4E400N02-CE4 WSM23G insert by Walter Tools is formulated for rostfreier Stahl and for heat‑resistant superalloys and titanium (ISO groups M and S). How does the Tiger‑tec Gold coating benefit production? The Tiger‑tec Gold coating on the SX-4E400N02-CE4 WSM23G improves wear resistance and edge life, which helps maintain consistent cutting performance in longer production runs. What role does the 4E400N02-CE4 chipbreaker play? The 4E400N02-CE4 chipbreaker delivers controlled chip formation, enabling safer feeds and better process security when machining tough or heat‑sensitive materials with the Walter Tools insert. Is this insert suitable for both turning and milling? Yes, the SX-4E400N02-CE4 WSM23G is an indexable insert intended for turning and milling applications where rostfreier Stahl and similar alloys are processed. Will this grade help reduce tool change frequency? The WSM23G grade in combination with Tiger‑tec Gold coating is chosen to enhance edge stability and wear resistance, which typically reduces the need for frequent insert changes during production. Can the insert improve surface finish on difficult materials? Thanks to the stable cutting edge and optimised chip control of the SX-4E400N02-CE4 WSM23G, users can expect more consistent surface quality when machining rostfreie Stähle and superalloys. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and product names are the property of their respective owners. Brand names are mentioned solely for clarification and comparison. There is no affiliation between our company and the mentioned brands. The offered article is an original, factory‑new product of the manufacturer Walter Tools.
SX-4E400N02-CE4 WSM23S WSM23S Wendeplatten - Walter Tools
Combine high thermal resistance and reliable chip control with an engineered grade for demanding materials; the result is higher process security and extended tool life when machining stainless steel and superalloys. Order directly via Metav Werkzeuge or contact our technical consultants for application support. SX-4E400N02-CE4 WSM23S turning & milling indexable insert — Tiger‑tec Silver by Walter Tools The SX-4E400N02-CE4 WSM23S is a coated indexable insert designed for heavy-duty machining of stainless steel and high-temperature alloys, offering optimised chip control and a durable cutting edge. Tiger‑tec Silver coating for heat resistance Optimised chipformer 4E400N02‑CE4 Grade WSM23S for stainless steel and S materials Stable cutting edge and long tool life Greater process security through coating and grade The combination of the Tiger‑tec Silver coating and the WSM23S grade delivers a measurable improvement in machining consistency when working with stainless steel and heat-resistant alloys. The coating provides a thermal barrier and reduces adhesion at the cutting edge, while the grade chemistry is tailored for high-temperature stability. For production environments that demand repeatable results, this insert reduces the frequency of edge failures and supports steady cycle times, translating into fewer interruptions on the shop floor and enhanced overall equipment effectiveness. Predictable chip control and improved surface quality The 4E400N02‑CE4 chipformer is engineered for controlled chip breaking and evacuation under demanding conditions. Controlled chip formation reduces the risk of built-up edge and protects the geometry of the toolholder and workpiece. As a consequence, manufacturers can expect more consistent surface finishes and reduced secondary operations. In practice, the chipformer shape helps to guide chips away from the cut, which simplifies coolant management and keeps tool paths clear, supporting higher productivity in continuous operations. Application-focused benefits and easy integration As a coated carbide solution within the Tiger‑tec Silver series, the insert is intended for roughing and semi-finishing of stainless steel and S-class materials such as titanium and nickel‑based superalloys. The design supports reliable feed rates at elevated temperatures and is compatible with common clamping systems for indexable inserts. Selection of the correct geometry and cutting parameters will further enhance tool life; consult the grade and chipformer data to match cutting speeds and feeds to the specific alloy. The result is durable performance with predictable wear behaviour and fewer unplanned tool changes. Contact Metav Werkzeuge for tailored application advice on Walter Tools Tiger‑tec Silver inserts or request a machining recommendation by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: SX-4E400N02-CE4-WSM23S-WALTER ISO designation: SX-4E400N02-CE4 WSM23S Series: Tiger‑tec Silver Grade: WSM23S Chipformer: 4E400N02‑CE4 Material groups: S / M Product type: Drehwendeschneidplatte / Fräswendeschneidplatte Manufacturer: Walter Tools Core data ISO designation: SX-4E400N02-CE4 WSM23S Special features Coating technology: Tiger·tec Silver (coated carbide) Grade description: WSM23S — coated cemented carbide Application: machining of stainless steel and S-class superalloys Chip control: optimised chipformer for stable chips Series purpose: heavy-duty machining and thermal stability FAQ Which materials is this insert suitable for? The SX-4E400N02-CE4 WSM23S insert is suitable for stainless steel and S-class materials (heat-resistant superalloys and titanium) as indicated by its grade and chipformer design. What does the Tiger‑tec Silver coating provide? The Tiger‑tec Silver coating on the WSM23S grade improves thermal resistance and reduces adhesion at the cutting edge, increasing tool life during high-temperature machining. For which machining tasks is the 4E400N02‑CE4 chipformer optimised? The 4E400N02‑CE4 chipformer is optimised for roughing and semi-finishing operations where controlled chip breaking and evacuation are critical to maintain process stability. Can this insert achieve good surface quality on stainless steel? Yes — when combined with appropriate geometry and cutting parameters, the SX-4E400N02-CE4 WSM23S supports improved surface finishes through reduced built‑up edge and consistent chip formation. What distinguishes the WSM23S grade from general-purpose grades? WSM23S is a coated cemented carbide grade developed for thermal stability and edge robustness in demanding materials, offering longer life under high temperatures compared with standard grades. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and product names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only; there is no affiliation between our company and the mentioned brands. The offered item is an original, factory-new product of the manufacturer. The Walter AG (brand appearance: Walter Tools) is a recognised provider of precision tools and is associated with international tool groups to deliver consistent quality and performance.
SX-4E400N02-CE4 WSM33G WSM33G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold wear resistance, a stable cutting edge and optimised chip control for reliable machining of stainless steels and heat‑resistant alloys. Order the SX-4E400N02-CE4 WSM33G through Metav Werkzeuge or request application advice from our consultants. SX-4E400N02-CE4 WSM33G — Tiger·tec Gold turning/milling indexable insert by Walter Tools The SX-4E400N02-CE4 WSM33G is a coated carbide indexable insert designed for turning and milling operations on stainless steels and heat‑resistant superalloys, delivering stable edge life and secure chip formation. Tiger·tec Gold coating for superior wear resistance Stable cutting edge for demanding materials Optimised chipformer for secure chip control Suitable for stainless steels and superalloys Longer tool life under thermal stress The Tiger·tec Gold coating technology and the WSM33G grade combine to improve resistance to thermal degradation during high‑energy cutting. As a coated carbide insert, the geometry and surface layers are engineered to reduce the risk of built‑up edge when machining ISO group M (rostfreie Stähle) and group S materials. This results in a more consistent tool life and fewer unplanned tool changes, which supports a smoother production flow and predictable cycle times for batch and continuous operations. Better surface finish and fewer interruptions The insert’s optimised chipformer, specified as 4E400N02-CE4, enhances chip control, reducing entanglement and promoting steady evacuation. Improved chip behaviour lowers the incidence of surface defects and minimises secondary finishing work. For manufacturers aiming for repeatable part quality, the stable cutting performance translates into reduced rejects and higher overall productivity while preserving component tolerances and surface integrity. Process reliability and application flexibility Designed for the challenges of hard‑to‑machine alloys, this indexable solution offers operators a robust balance of edge stability and wear resistance, making it suitable for roughing and semi‑finishing passes on stainless steels and heat‑resistant materials. Integration with common toolholder systems is straightforward, and the grade’s focus on thermal and mechanical stability helps maintain cutting performance across variable feeds and speeds. For specific application parameters or to verify suitability for a particular alloy, Metav Werkzeuge provides expert consultation and technical data to support process optimisation. For reliable machining of stainless steels and superalloys, contact Metav Werkzeuge for availability and application advice on the Walter Tools SX-4E400N02-CE4 WSM33G at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: SX-4E400N02-CE4-WSM33G-WALTER Article: SX-4E400N02-CE4 WSM33G Product type: Turning/milling indexable insert Series: Tiger·tec Gold Grade: WSM33G Chipformer: 4E400N02-CE4 Manufacturer: Walter Tools Data Applicable material groups: M (rostfreie Stähle), S (superalloys/titanium) Coating technology: Tiger·tec Gold Material designation: coated carbide Material application code: S / M Special features Designed for hard‑to‑machine materials Focus on thermal stability and edge strength Optimised chip control for steady evacuation Suitable for roughing and semi‑finishing operations FAQ What materials is this insert suitable for? The SX-4E400N02-CE4 WSM33G is intended for rostfreie Stähle (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), offering thermal stability and secure chip formation. How does the Tiger·tec Gold technology help in production? Tiger·tec Gold coating on the WSM33G grade increases wear resistance and thermal tolerance, which prolongs cutting edge life and stabilises machining performance under elevated temperatures. Which chipformer does the insert use and what is the benefit? The insert features the 4E400N02-CE4 chipformer, optimised for reliable chip breaking and evacuation to reduce surface defects and minimise interruptions during turning and milling operations. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation purposes only; there is no connection between our company and the mentioned brands. The offered item is an original, factory‑new product of Walter Tools.
SX-4E400N02-CE4 WSM43G WSM43G Wendeplatten - Walter Tools
Combine proven Tiger·tec Gold coating performance with a stable cutting edge and reliable chip control for consistent machining of demanding alloys — order directly via Metav Werkzeuge or consult our advisors for application support. SX-4E400N02-CE4 WSM43G — Indexable insert / Milling insert, Tiger·tec Gold (Walter Tools) The SX-4E400N02-CE4 WSM43G is an indexable insert engineered for heavy-duty turning and milling, optimised for machining rostfreier Stahl and heat-resistant superalloys. Tiger·tec Gold coated grade WSM43G Supported for rostfreier Stahl and superalloys Stable cutting edge and reliable chip control Consistent performance on difficult-to-machine materials The combination of the Tiger·tec Gold coating and the WSM43G grade delivers proven wear resistance and thermal stability for extended service life. The coating technology on this coated carbide grade reduces flank wear and helps maintain a sharp edge under elevated temperatures typically encountered when machining rostfreier Stahl or superalloys. The integrated chip control geometry (chipbreaker code 4E400N02-CE4) promotes predictable chip formation, lowering the risk of built-up edge and enabling more consistent cycle times. This technical design focuses on process stability to reduce unscheduled interruptions and improve overall throughput. Improve process reliability and surface quality A robust cutting edge and optimised micro-geometry ensure that the insert maintains performance over longer tool life, which translates into fewer tool changes and more productive machining shifts. The stable cutting edge reduces vibration sensitivity and supports a reliable surface finish even under heavy cutting forces. For production environments where repeatability matters, this grade contributes to predictable tolerances and reduced rework. The economic benefit is realised through higher machining reliability and a more favourable ratio of material removal to tool consumption, especially when processing high-temperature alloys and rostfreier Stahl. Practical application and selection guidance As an indexable insert for both turning and milling applications, the SX‑4E400N02‑CE4 WSM43G is suitable where thermal resistance and edge stability are required. Selection of the correct chipbreaker and insert geometry is essential: the 4E400N02-CE4 chipbreaker is tailored to support secure chip evacuation and reduce the incidence of built-up edge with ductile, heat-generating materials. For specific holder compatibility or suggestions on cutting data for particular rostfreier Stahl grades and superalloys, the insert’s characteristics should be matched to machine rigidity and workpiece requirements. If further technical clarification is needed, application-focused advice is available to ensure the best process outcome. Request application advice or availability for the Walter Tools Tiger·tec Gold SX-4E400N02-CE4 WSM43G insert from Metav Werkzeuge — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical data SKU: SX-4E400N02-CE4-WSM43G-WALTER ISO designation: SX-4E400N02-CE4 WSM43G Product: Drehwendeschneidplatte / Fräswendeschneidplatte Series: Tiger·tec Gold Grade: WSM43G Manufacturer: Walter Tools Facts Applicable material groups: S / M Chipbreaker: 4E400N02-CE4 Coating technology: Tiger·tec Gold coated carbide Special features Optimised chip formation Stable cutting edge and high process security Suitable for rostfreier Stahl and heat-resistant superalloys Designed for heavy-duty turning and milling FAQ Which materials is this insert best suited for? The SX-4E400N02-CE4 WSM43G indexable insert (Walter Tools) is specified for ISO groups S and M, making it suitable for heat-resistant superalloys and rostfreier Stahl. What benefits does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating on the WSM43G grade increases thermal stability and wear resistance, helping to preserve the cutting edge and extend service life under elevated temperatures. Which chipbreaker should be used for ductile rostfreier Stahl? The chipbreaker 4E400N02-CE4 integrated with this insert supports secure chip control and reduced built-up edge when machining ductile rostfreier Stahl and similar alloys. Is the insert suitable for both turning and milling? Yes, the SX-4E400N02-CE4 WSM43G is designed as an indexable insert for demanding turning and milling tasks where edge stability and process reliability are required. Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanation. There is no connection between our company and the mentioned brands. The offered article is original, factory-new goods from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
SX-4E400N02-CE4 WSM43S WSM43S Wendeplatten - Walter Tools
High wear resistance and secure chip control reduce rework and extend tool life; combined with the Tiger·tec Silver technology this insert delivers consistent performance when machining rostfreier Stahl and heat-resistant alloys. Order the insert directly via Metav Werkzeuge or ask the consultants if additional process data is required. SX-4E400N02-CE4 WSM43S — Indexable insert for turning and milling, Tiger·tec Silver · Walter Tools The SX-4E400N02-CE4 WSM43S is an indexable insert engineered for high-temperature alloys and rostfreier Stahl, offering stable cutting edges and reliable chip control for demanding production environments. Tiger·tec Silver coating for longer tool life Grade WSM43S for rostfreier Stahl and superalloys 4E400N02-CE4 chipbreaker for stable chip formation Precision indexable insert for turning and milling Consistent performance in demanding materials The combination of the WSM43S grade and Tiger·tec Silver coating provides improved wear resistance and heat tolerance, which translates into fewer tool changes and more predictable production cycles. As a coated cemented carbide solution, this insert copes with the adhesion tendencies and thermal loads typical of rostfreier Stahl and nickel‑based superalloys, reducing the risk of built‑up edge and preserving the cutting edge geometry. Such stability supports higher feed rates and contributes to measurable increases in line throughput. Reduced downtime through longer edge life A focus on stability and repeatability ensures that the insert maintains a sharp, usable edge over extended runs. The WSM43S grade is optimised for heat resistance and abrasion control, so the replacement intervals become more predictable and maintenance windows can be planned. This leads to improved overall equipment effectiveness and lower per‑part machining costs. The result is a more efficient turning and milling process with consistent surface finishes and fewer scrap parts. Predictable chip control for safer machining The 4E400N02-CE4 chipbreaker geometry is designed to produce short, controllable chips under high thermal and mechanical loads. Controlled chip formation reduces the incidence of tangled swarf and supports automated chip handling systems, while also lowering the likelihood of surface damage from recirculating chips. Clear chip control improves operator safety and contributes to a cleaner, more reliable machining environment—particularly important when processing materials that generate continuous, stringy chips. Versatile compatibility and simple integration As a dual‑purpose insert for both turning and milling operations, this product simplifies tool inventory and selection. The insert suits a range of toolholders and machine setups where a reliable, coated carbide grade is required for high‑temperature alloy machining. Selection is straightforward thanks to the clear grade and series designation; matched with appropriate cutting parameters, the insert delivers consistent tool life and surface quality across batch and prototype production. For expert application advice or to order the SX-4E400N02-CE4 WSM43S, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 — Metav Werkzeuge can support process matching and delivery details Technical data SKU: SX-4E400N02-CE4-WSM43S-WALTER Designation: SX-4E400N02-CE4 WSM43S Product type: Turning/milling indexable insert Brand: Walter Tools Core data Series: Tiger·tec Silver Grade: WSM43S Chipbreaker: 4E400N02-CE4 Material applicability: ISO groups M, S Special features Coated cemented carbide Optimised for rostfreier Stahl and superalloys Stable cutting edge and secure chip control Suitable for demanding, high‑temperature machining FAQ What materials is this insert suited for? The SX-4E400N02-CE4 WSM43S is intended for rostfreier Stahl and heat‑resistant superalloys (ISO groups M and S), delivering reliable performance where thermal loads and adhesion are critical. How does the Tiger·tec Silver series benefit machining? The Tiger·tec Silver coating on the WSM43S grade increases heat resistance and wear protection, which helps extend the insert’s service life and maintain consistent surface quality during extended runs. Is this insert suitable for both turning and milling? Yes, the designation and geometry make the insert compatible with appropriate turning and milling toolholders, allowing flexible use across different metalcutting operations. What advantage does the 4E400N02-CE4 chipbreaker provide? The 4E400N02-CE4 chipbreaker promotes short, predictable chips under heavy thermal loads, improving swarf management and reducing the risk of surface damage from recirculating chips. Which brand manufactures the insert and what is its reputation? The insert is supplied by Walter Tools, a brand known for high‑precision cutting solutions and tools optimised for productive machining and consistent results. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Die Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is a leading provider of precision tools for metalworking. Protected trademarks and product names are the property of their respective owners. Mark names and designations are used here for explanation only; there is no affiliation between our company and the trademark owners. The offered article is an original, factory‑new product of the manufacturer.
SX-4E400N02-CF5 WSM33G WSM33G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the WSM33G grade for reliable machining of stainless steel and heat‑resistant superalloys; this insert provides stable chip formation and extended edge life for consistent production. For order inquiries or application advice, contact Metav Werkzeuge or request consultancy support. SX-4E400N02-CF5 WSM33G – indexable turning and milling insert with Tiger·tec Gold coating | Walter Tools The SX-4E400N02-CF5 WSM33G is a Tiger·tec Gold coated indexable insert designed for turning and milling applications on stainless steel and high‑temperature alloys, offering heat resistance and cutting‑edge stability for demanding machining tasks. Tiger·tec Gold coated for heat resistance Stable chip formation for tough materials Suitable for stainless steel and superalloys Enhanced edge life for productive machining High-temperature performance for demanding alloys The combination of the Tiger·tec Gold coating and the WSM33G carbide substrate delivers high thermal stability and wear resistance for machining materials that generate elevated cutting temperatures. Coated carbide means a hard substrate with a surface film engineered to reduce friction and improve oxidation resistance; in practice this reduces flank wear and maintains cutting geometry during longer cycles. This behaviour is particularly relevant when working with stainless steel and nickel‑based materials, where heat tends to concentrate at the cutting edge and standard grades can fail prematurely. The result is a predictable tool life and fewer unscheduled tool changes, which supports efficient production planning. Reliable chip control and consistent cutting edges The insert’s geometry and the specified chipbreaker (4E400N02‑CF5) promote stable chip formation, reducing build‑up and chaotic chip shapes that increase cutting forces and risk surface defects. Stable chips facilitate automatic chip evacuation and help protect the machine and workpiece from interruptions. With reduced edge degradation, the component surface finish remains consistent for longer, lowering rework rates. For operations where repeatability and cycle stability matter, this translates into measurable gains in throughput and reduced scrap. Versatile for turning and milling with predictable results Designed as a combined turning and milling grade, the insert designation supports a range of toolholder geometries and cutting conditions, depending on the selected insert pitch and holder. The coated carbide composition and the Tiger·tec Gold technology make it suitable for heavy interrupted cuts as well as continuous finishing passes when the tool geometry permits. Process security is improved through a balance of toughness and hardness in the grade: toughness protects the cutting edge during shock loads, hardness maintains sharpness for surface quality. Operators and tool planners will therefore find this insert useful where flexibility and consistent part quality are required. Operational advantages for workshop managers Adopting this grade can lower total machining costs by extending the period between indexings and reducing downtime for tool changes. The predictable wear pattern and enhanced edge life shorten setup routines and simplify inventory handling for consumables. For customers needing application data or cutting parameter recommendations for specific machines and workpiece alloys, Metav Werkzeuge offers technical guidance and can assist in selecting the optimal geometry and cutting speeds to match the required surface finish and cycle time objectives. For tailored application support or to arrange supply of Walter Tools inserts, contact Metav Werkzeuge by eMail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for prompt consultancy and delivery options Technical data Article number: SX-4E400N02-CF5-WSM33G-WALTER Identification: SX-4E400N02-CF5 WSM33G Product type: Drehwendeschneidplatte / Fräswendeschneidplatte Series: Tiger‑tec Gold Grade: WSM33G Chipbreaker: 4E400N02‑CF5 Manufacturer: Walter Tools UID: SX-4E400N02-CF5-WSM33G-WALTER Core specifications Material group: S / M Suitable for stainless steel: Yes Features and applications Coating: Tiger·tec Gold (coated carbide) Typical application: Heavy and difficult‑to‑machine alloys, depending on geometry also stainless steel Benefits: Stable chip formation, edge stability, enhanced tool life FAQ What materials is this insert suitable for? The SX-4E400N02-CF5 WSM33G is optimised for machining stainless steel and heat‑resistant superalloys; its Tiger·tec Gold coating supports high cutting temperatures and stable chip control. Does the WSM33G grade improve tool life compared with uncoated grades? Yes, the WSM33G grade with Tiger·tec Gold coating improves oxidation resistance and wear performance, which typically extends edge life and reduces the frequency of indexing. Which chipbreaker does this insert use and what is its effect? The insert uses the 4E400N02‑CF5 chipbreaker, designed to promote controlled chip formation and reliable evacuation, leading to fewer interruptions and improved surface consistency. Can this insert be used for both turning and milling operations? The designation indicates suitability for combined turning and milling uses when mounted in compatible toolholders and matched to the correct geometry; the coated carbide composition provides the necessary toughness and wear resistance. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade designations are mentioned for explanatory purposes only; no connection exists between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer.
SX-4E400N02-CF5 WSM43G WSM43G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold heat resistance, WSM43G coating stability and optimised chip control for reliable machining of difficult-to-cut materials; order the insert directly via Metav Werkzeuge or contact our consultants for application advice. SX-4E400N02-CF5 WSM43G — turning/milling indexable insert, Tiger·tec Gold (Walter Tools) The SX-4E400N02-CF5 WSM43G is a coated carbide indexable insert designed for demanding turning and milling tasks, optimised for difficult-to-cut materials and rostfreier Stahl in industrial metalworking applications. Tiger·tec Gold coating for heat resistance WSM43G grade for tough materials Optimised chip control with CF5 geometry Suitable for rostfreier Stahl and superalloys Longer tool life through heat-resistant coating and grade The combination of the Tiger·tec Gold coating and the WSM43G grade provides distinct advantages in high-temperature cutting. The multilayer coating increases heat resistance and reduces crater wear, which in turn stabilises the cutting edge and extends tool life. For production environments where thermal loads and built‑up edge formation are common, this coated carbide solution ensures more predictable component runs and less frequent indexable insert changes, resulting in higher overall equipment effectiveness and fewer unscheduled interruptions. Stable process and improved surface quality from optimised geometry The CF5 chipbreaker geometry (4E400N02-CF5) supports consistent chip control and predictable chip evacuation. A controlled chip flow reduces vibration and prevents entanglement, which helps to achieve a better surface finish on machined parts and reduces rework. In practice this means fewer cycle interruptions, a lower risk of tool breakage and a more consistent part quality in series production. The geometry is particularly effective when machining materials known for poor thermal conductivity and high ductility, where chip control is critical. Suitable applications and handling guidance for demanding materials This indexable insert is intended primarily for use on rostfreier Stahl and heat‑resistant superalloys and titanium (ISO group M and S), where abrasive wear and heat concentration challenge the cutting edge. The substrate and coating combination is tailored to maintain a stable cutting edge under these conditions. When integrating the insert into a machining process, select a tool holder and cutting parameters appropriate for coated carbide inserts and monitor feed and speed to balance tool life and component accuracy. If additional technical data is needed for setup, Metav Werkzeuge can provide support. Contact Metav Werkzeuge for expert advice on Walter Tools' Tiger·tec Gold insert WSM43G — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: SX-4E400N02-CF5-WSM43G-WALTER Designation: SX-4E400N02-CF5 WSM43G Product type: turning/milling indexable insert Series: Tiger·tec Gold Grade: WSM43G Manufacturer: Walter Tools Key specifications Geometry: 4E400N02-CF5 Material group suitability: S / M (ISO 513) Applicable material focus: rostfreier Stahl Special features Coated carbide grade WSM43G Tiger·tec Gold coating technology Optimised chip control via CF5 geometry Designed for difficult-to-cut materials and rostfreier Stahl Suitable for both turning and milling operations FAQ What materials is this insert suitable for? The SX-4E400N02-CF5 WSM43G insert is designed for rostfreier Stahl and heat‑resistant superalloys (ISO groups M and S), offering stable edge performance in demanding cuts. Which series and coating does the insert use? The insert belongs to Walter Tools' Tiger·tec Gold series; the WSM43G grade is a coated carbide formulation optimised for thermal stability. How does the CF5 geometry affect machining? The CF5 chipbreaker promotes controlled chip formation and evacuation, improving surface finish and reducing the likelihood of built‑up edge during the machining of tough materials. Is this insert intended for turning, milling or both? This product is specified as a turning/milling indexable insert and can be applied in both operations depending on holder and machine setup. Who can provide setup advice for this insert? Metav Werkzeuge can assist with recommended cutting parameters and holder selection for the SX-4E400N02-CF5 WSM43G insert. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SX-4E400N02-CK8 WK1 Wendeplatten - Walter Tools
Taking advantage of the combination of stable chip control, uncoated carbide reliability, and straightforward process integration ensures predictable cutting behaviour and productive machining cycles; order the SX-4E400N02-CK8 WK1 insert via Metav Werkzeuge or request the product matrix for precise material allocation. SX-4E400N02-CK8 WK1 — Turning and milling indexable insert, uncoated carbide by Walter Tools The SX-4E400N02-CK8 WK1 is an indexable insert for turning and milling that provides controlled chip formation and consistent cutting performance for general machining tasks, with material suitability to be verified against the manufacturer’s product matrix. Uncoated carbide grade WK1 Designed for turning and milling Chipformer 4E400N02-CK8 Manufactured by Walter Tools High-performance cutting with controlled chip formation The uncoated carbide composition of this cutting grade delivers a predictable, sharp cutting edge that is particularly useful where consistent material removal and surface integrity matter. The integrated chipformer 4E400N02-CK8 shapes and evacuates chips reliably, reducing the risk of re-cutting and improving cycle stability. For production environments where tool-change intervals and process repeatability drive costs, the indexable insert design supports efficient replacement and keeps spindle downtime to a minimum while maintaining dimensional consistency. Adaptable geometry for mixed turning and milling tasks The insert geometry has been developed to suit both turning and milling toolholders, enabling versatile deployment across a cell or machine park. The cutting edge and seating features allow stable clamping and predictable insert positioning, which helps to reduce setup variation and simplify tool management. As a consequence, process engineers benefit from straightforward tool lists and repeatable results when migrating operations between machines or when standardising a cutting strategy with smaller inventory ranges. Clear guidance on material suitability and application limits The WK1 grade is an uncoated carbide type intended for broad use, but the specific workpiece materials and cutting conditions must be validated against the official product matrix. Material compatibility and recommended cutting parameters are determined by that matrix; checking it avoids inefficient tool choices and ensures safe, economic machining. Where high-temperature alloys or abrasive materials are present, selecting the correct grade and cutting data will protect the cutting edge and deliver longer life with consistent surface finish. Brand-level reliability and productive machining Walter Tools’ open series carbide grades are engineered for robust performance and steady process outcomes. The series philosophy supports stable edge formation and repeatable results in everyday production settings, delivering the predictable behaviour that manufacturers rely on for batch consistency. For applications requiring optimisation, consulting the product matrix and discussing the insert geometry with technical advisers helps to align tool selection with throughput and surface quality goals. Discuss application requirements with Metav Werkzeuge to confirm the SX-4E400N02-CK8 WK1 is the right insert for the intended operation, request the product matrix for material allocation, or obtain tailored application advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number / SKU: SX-4E400N02-CK8-WK1-WALTER Label: Drehwendeschneidplatte / Fräswendeschneidplatte SX-4E400N02-CK8 WK1 Walter Tools Product type: Turning and milling indexable insert Data No numerical data available in the supplied dataset Special features Grade: WK1 (uncoated carbide) Chipformer: 4E400N02-CK8 Series: Walter Schneidstoffsorte - Serie offen Base designation: SX-4E400N02-CK8 ISO designation: SX-4E400N02-CK8 WK1 Manufacturer: Walter Tools FAQ What materials is this insert suitable for? Material suitability must be confirmed with the product matrix; the SX-4E400N02-CK8 WK1 is an uncoated carbide grade intended for broad applications but requires specific verification for each workpiece material. Is the insert coated or uncoated? The SX-4E400N02-CK8 WK1 is supplied as an uncoated carbide grade, offering a sharp cutting edge and predictable wear behaviour under appropriate cutting conditions. Can this insert be used for both turning and milling? Yes — the geometry and designation indicate suitability for turning and milling toolholders, allowing flexible deployment across mixed machining operations. What does the chipformer designation mean? The chipformer 4E400N02-CK8 describes the insert’s chip control geometry; it is designed to shape and eject chips consistently to support stable cutting cycles. How should suitability be verified before production use? Consult the Walter Tools product matrix and machining data to match the WK1 grade, chipformer and cutting parameters to the specific workpiece material and operation. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen
SX-4E400N02-SF5 WSM33G WSM33G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold coating and the WSM33G carbide grade for dependable chip control, thermal resistance and longer cutting-edge life in hard-to-machine materials; order directly via Metav Werkzeuge or consult the team for application-specific recommendations. SX-4E400N02-SF5 WSM33G Turning / Milling indexable insert – for stainless steels and superalloys | Walter Tools The SX-4E400N02-SF5 WSM33G is a coated carbide insert designed for demanding turning and milling tasks, optimised for machining stainless steels and heat‑resistant superalloys under the Tiger·tec Gold technology. Tiger·tec Gold coated grade WSM33G Optimised for stainless steels and superalloys Robust cutting edge for stable chip control Designed for productive finishing and roughing Consistent performance in hard‑to‑machine materials The combination of the WSM33G carbide grade and Tiger·tec Gold technology delivers a coating system and substrate tailored to applications with poor heat conduction and high work‑hardening tendency. For stainless steels (ISO group M) and heat‑resistant alloys and titanium (ISO group S) this results in improved thermal resistance at the cutting edge and reduced risk of build‑up on the tool face. Clinically, that means more predictable cutting forces, fewer interrupted cuts and a higher degree of process stability when machining components that otherwise shorten tool life. Stable cutting edge for repeatable surface quality A stable cutting edge reduces variability between components and lowers scrap rates. The insert’s design promotes stable chip control, which decreases the frequency of rework and supports a constant surface finish across batches. Stability at the edge also contributes to extended tool life, reducing changeover intervals and supporting predictable maintenance planning. In production environments where repeatability matters, this reliability directly supports throughput and quality objectives without complex parameter changes. Flexibility across turning and milling operations This indexable insert is suitable for both turning and milling toolholders when the geometry and seat match the application. The insert’s geometry code indicates a specific chipbreaker and corner configuration aimed at productive machining—the result is versatility for light finishing cuts as well as more demanding roughing passes. By selecting the correct seat and cutting parameters, the same insert family can be deployed across multiple operations, simplifying inventory and enabling rapid changeovers on mixed‑product lines. Process advantages on the shop floor Fewer insert changes and consistent cutting performance translate into measurable shop‑floor advantages: reduced downtime, lower tooling consumption and more stable cycle times. The engineered coating and grade combination supports higher cutting speeds where applicable, improving overall productivity while maintaining component accuracy. For technical queries or to verify suitability for a specific alloy or geometry, Metav Werkzeuge provides application guidance and machining data to help integrate the insert into existing setups with minimal trial time. Contact Metav Werkzeuge to discuss the SX-4E400N02-SF5 WSM33G application and obtain tailored machining advice for optimal process results Technical Data SKU: SX-4E400N02-SF5-WSM33G-WALTER Article designation: SX-4E400N02-SF5 WSM33G Product type: Turning / milling indexable insert Manufacturer: Walter Tools Core specifications Grade: WSM33G (coated carbide) Series: Tiger·tec Gold Geometry / chipbreaker: 4E400N02-SF5 Material suitability: stainless steels (M), superalloys/titanium (S) Features & applications Coating technology: Tiger·tec Gold Stable cutting edge Optimised chip control Suitable for finishing and roughing operations FAQ What materials is this insert designed for? The SX-4E400N02-SF5 WSM33G insert is designed for stainless steels (ISO group M) and heat‑resistant superalloys and titanium (ISO group S), offering thermal resistance and stable cutting behaviour in these materials. How does the Tiger·tec Gold technology benefit machining? Tiger·tec Gold enhances the WSM33G grade with a coating system that increases edge strength and thermal stability, leading to improved chip control and longer service life under heavy thermal loads. Can this insert be used for both finishing and roughing? Yes, the geometry and chipbreaker make the insert suitable for both finishing and roughing operations, allowing flexible deployment across turning and milling when paired with matching holders and parameters. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik‑Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
SX-4E400N02-SF5 WSM43G WSM43G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, the WSM43G grade and proven cutting-edge stability to achieve consistently productive machining of rostfreier Stahl and heat-resistant superalloys; order directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. SX-4E400N02-SF5 WSM43G – Indexable turning/milling insert, Tiger·tec Gold coating, for rostfreier Stahl and superalloys | Walter Tools The SX-4E400N02-SF5 WSM43G is an indexable insert engineered for demanding turning and milling of rostfreier Stahl and heat-resistant superalloys, offering a balance of thermal resistance and edge robustness for high-performance metalcutting. Tiger·tec Gold coating for thermal resistance WSM43G grade suited to rostfreier Stahl and superalloys Stable cutting edge for productive machining Applicable in both turning and milling operations Reliable thermal resistance for heavy-duty cutting The Tiger·tec Gold coating combined with a high-performance coated carbide substrate provides elevated thermal stability, which directly reduces flank wear under the high temperatures typical for machining rostfreier Stahl and superalloys. This thermal resilience translates into longer effective tool life and fewer insert changes, supporting uninterrupted production cycles. By favouring a grade optimised for heat and edge integrity, the insert helps maintain dimensional accuracy across longer batch runs, lowering overall process variability. Better chip control and consistent surface quality The insert’s chipbreaking geometry (designated 4E400N02-SF5) and the WSM43G grade are matched to encourage reliable chip formation when cutting difficult materials. Improved chip control reduces rework and safeguards the workpiece surface, which is particularly important for components requiring tight tolerances and superior finish. In practical terms, stable chips mean quicker cycle times and less downtime for manual chip clearing, contributing to a more predictable machining process and enhanced throughput. Fewer tool variants, more process flexibility Designed for both turning and milling applications, this indexable insert reduces the need for multiple specialised grades in the tool crib. Compatibility with ISO material groups M (rostfreie Stähle) and S (heat-resistant superalloys and titanium) allows one insert geometry to cover several workpiece families, simplifying inventory and tool selection. The result is a streamlined tooling strategy: fewer setups, easier logistics and a clearer path to consistent machining results across different components. Practical advantages for workshop efficiency The combination of WSM43G and the Tiger·tec Gold family focuses on stable edge life and controlled wear mechanisms. For engineers and production planners, this means predictable performance metrics such as tool-life intervals and surface finish repeatability. Where cycles must be reproducible and documentation of process windows is required, the insert offers a transparent baseline for feed and speed adjustments. The clear technical profile aids in parameter tuning and reduces trial-and-error iterations on the machine. Contact Metav Werkzeuge for tailored cutting recommendations or to discuss how the Walter Tools SX-4E400N02-SF5 WSM43G can be integrated into existing processes — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: SX-4E400N02-SF5-WSM43G-WALTER Type: Indexable turning and milling insert Brand: Walter Tools Series: Tiger·tec Gold Grade: WSM43G Chipbreaker: 4E400N02-SF5 ISO designation: SX-4E400N02-SF5 WSM43G Data ISO material groups: M, S Suitable materials indication: rostfreier Stahl; heat-resistant superalloys Special features Coating: Tiger·tec Gold Substrate: coated carbide Applications: turning and milling Benefits: thermal stability, chip control, cutting-edge stability FAQ What materials is this insert best suited for? The SX-4E400N02-SF5 WSM43G is specified for rostfreier Stahl (ISO group M) and heat-resistant superalloys (ISO group S), offering thermal and edge stability for these demanding materials. How does the Tiger·tec Gold coating improve performance? The Tiger·tec Gold coating increases heat resistance and reduces abrasive wear, which helps the WSM43G grade preserve cutting-edge geometry and extend useful tool life during high-temperature machining. Can this insert be used in both turning and milling applications? Yes, the insert geometry and chipbreaker are designed for versatility in both turning and milling operations, reducing the need for multiple specialised inserts. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com