TS22-IR2.0ISO-3 WMP32G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating, the WMP32G grade optimised for stainless steels and the IR2.0ISO‑3 chipbreaker for secure chip control; this yields reliable tool life and predictable machining cycles. Order the insert directly via Metav Werkzeuge or contact our consultants for application advice. TS22-IR2.0ISO-3 WMP32G – Indexable turning insert for stainless steels, Tiger‑tec Gold by Walter Tools The TS22-IR2.0ISO-3 WMP32G is an indexable turning insert engineered for machining stainless steels under medium to robust cutting conditions, combining a Tiger·tec Gold coating with a chipbreaker tailored to ISO group M applications Tiger·tec Gold coating for enhanced wear resistance Designed for stainless steels (ISO group M) IR2.0ISO‑3 chipbreaker for secure chip control Consistent performance in medium to heavy cuts Safer, more consistent machining of stainless steels The combination of the WMP32G grade and the Tiger·tec Gold technology delivers a coating and substrate pairing that improves edge stability when working with stainless steels, which are prone to work hardening and built-up edge. The design supports stable chip formation, reducing interruptions and helping to maintain surface integrity. For users seeking predictable tool life, this insert offers a clear operational advantage by lowering the risk of sudden edge failure during continuous or interrupted turning processes. Raise productivity through controlled cutting behaviour Equipped with the IR2.0ISO‑3 chipbreaker, the insert promotes reliable chip control and evacuation, which in turn reduces cycle-time variability and cleaning downtime. The geometry is optimised for medium to heavy cuts common in production turning of ISO M materials, enabling higher metal removal rates while retaining surface quality. Improved process stability contributes to measurable efficiency gains and can support a positive cost-per-part calculation over time. Practical compatibility and application guidance As an indexable turning insert from Walter Tools’ Tiger‑tec Gold series, the component is classified for ISO group M, indicating suitability for a wide range of stainless steels. This means the grade and chipbreaker combination accommodates toughness and thermal sensitivity typical of these alloys. The plate is intended for standard toolholders compatible with the TS22 designation and serves applications where consistent edge life and dependable chip control are priorities. For tailored technical consultation on integrating the Tiger·tec Gold WMP32G grade into existing turning operations, contact Metav Werkzeuge for expert advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data SKU: TS22-IR2.0ISO-3-WMP32G-WALTER Designation: TS22-IR2.0ISO-3 WMP32G Product type: Indexable turning insert Brand: Walter Tools Facts Series: Tiger·tec Gold Grade: WMP32G (coated carbide) Application group: ISO M (stainless steels) Chipbreaker: IR2.0ISO‑3 Special features Optimised for stable chip formation in stainless steels Coating technology for enhanced wear resistance Suitable for medium to heavy cutting conditions Consistent edge stability for production environments FAQ What materials is this insert suited for? The insert is specified for stainless steels (ISO group M); the WMP32G grade and Tiger·tec Gold coating support stable cutting of these alloys. How does the IR2.0ISO‑3 chipbreaker affect performance? The IR2.0ISO‑3 chipbreaker improves chip control and evacuation, helping to maintain consistent cutting forces and reducing the likelihood of built‑up edge when turning stainless steels. Is this an original Walter Tools product? Yes, the TS22‑IR2.0ISO‑3 WMP32G is an original Walter Tools indexable turning insert from the Tiger·tec Gold series and supplied as new factory product. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
TS22-IR3.5ISO WMP22G Wendeplatten - Walter Tools
Take advantage of the combination of precise chip control, long tool life and Tiger·tec Gold coating for confident machining of rostfreier Stahl; order the TS22-IR3.5ISO WMP22G directly via Metav Werkzeuge or consult our advisors if required. TS22-IR3.5ISO WMP22G indexable turning insert, Tiger·tec Gold, IR3.5ISO – Walter Tools The TS22-IR3.5ISO WMP22G is an indexable turning insert engineered for stable chip formation and robust performance in rostfreier Stahl turning under medium to heavy cutting conditions. Tiger·tec Gold coating technology WMP22G grade for rostfreier Stahl IR3.5ISO chipbreaker for stable chips High wear resistance and edge stability Reliable chip control for demanding rostfreier Stahl turning The TS22-IR3.5ISO WMP22G delivers consistent chip control through its specially designed chipbreaker IR3.5ISO, which reduces the risk of built-up edge and long, stringy chips typical of rostfreier Stahl. Stable chip formation lowers the likelihood of interrupted cuts, which in turn reduces secondary operations and machine downtime. The chip geometry promotes predictable evacuation and safer swarf handling, supporting a steady production flow and improved surface quality with fewer process interruptions. Productivity through Tiger·tec Gold coating and WMP22G grade The combination of Tiger·tec Gold coating and the WMP22G coated-carbide grade enhances wear resistance and edge life during continuous turning. The multilayer coating improves heat resistance and adhesion, so the cutting edge retains geometry for longer under thermal and mechanical stress. For workshops this means fewer insert changes and better cost-efficiency per cutting hour, while still achieving the dimensional stability required in serial and batch production of rostfreier Stahl components. Easy integration into existing turning processes As an indexable turning insert, this insert fits standard toolholders and adapts to established turning cycles without complex setup changes. The geometry supports reproducible cutting forces and predictable tool behaviour, enabling straightforward parameter optimisation for cycle-time reduction. By maintaining a reliable edge over extended runs, the insert helps to avoid frequent regrinding or premature replacement, supporting leaner inventory management and improved overall equipment effectiveness. Clear material scope and application guidance Designed with ISO classification in mind, the insert is primarily matched to ISO group M materials and is optimised for rostfreier Stahl, which tends to be tough and heat-prone. The grade and chipbreaker are selected to address common challenges such as adhesion and thermal concentration; the result is a balance between cutting-edge strength and controlled chip removal. For operations requiring medium to robust machining of rostfreier Stahl, this insert offers a dependable solution that aligns with standard industrial cutting strategies. For reliable, high-performance turning of rostfreier Stahl with Walter Tools’ Tiger·tec Gold technology, request TS22-IR3.5ISO WMP22G via Metav Werkzeuge or arrange a technical consultation with our specialists at Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: TS22-IR3.5ISO-WMP22G-WALTER Description: Drehwendeschneidplatte TS22-IR3.5ISO WMP22G Walter Tools Manufacturer: Walter Tools Product type: Indexable turning insert Grade: WMP22G Series: Tiger·tec Gold Chipbreaker: IR3.5ISO ISO designation: TS22-IR3.5ISO WMP22G Suitable for: rostfreier Stahl Facts Material group: M UID: TS22-IR3.5ISO-WMP22G-WALTER Special features Coating technology: Tiger·tec Gold Grade type: coated carbide Optimised for stable chip formation with IR3.5ISO Intended use: medium to robust machining of rostfreier Stahl FAQ What materials is this insert suitable for? The TS22-IR3.5ISO WMP22G is tailored for ISO group M materials and is specifically suitable for machining rostfreier Stahl, where toughness and heat sensitivity demand secure chip control. What does the WMP22G grade and Tiger·tec Gold series mean? WMP22G denotes a Walter coated-carbide grade formulated for rostfreier Stahl; the Tiger·tec Gold series refers to the multilayer coating technology that increases heat resistance and wear performance. How does the IR3.5ISO chipbreaker affect machining? The IR3.5ISO chipbreaker produces shorter, controlled chips and reduces the tendency for built-up edge, resulting in improved surface finish and reduced risk of swarf-related interruptions during rostfreier Stahl turning. Can this insert be used in standard toolholders and processes? Yes, the indexable design of the insert is compatible with conventional turning toolholders and can be integrated into existing turning setups to achieve consistent cutting performance. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands beyond the sale of original, factory-new products of the manufacturer.
TS22-IR3.5ISO WMP32G Wendeplatten - Walter Tools
The combination of Tiger·tec Gold coating and the WMP32G grade delivers dependable machining of rostfreier Stahl, with optimised chip control from the IR3.5ISO chipbreaker and extended edge life; order the insert directly via Metav Werkzeuge or request application advice from our consultants. TS22-IR3.5ISO WMP32G — Indexable turning insert (Tiger·tec Gold, for rostfreier Stahl) by Walter Tools The TS22-IR3.5ISO WMP32G is an indexable turning insert engineered for reliable performance when machining rostfreier Stahl under medium to robust conditions Tiger·tec Gold coating for extended tool life IR3.5ISO chipbreaker for secure chip formation Optimised for rostfreier Stahl (material group M) Coated carbide grade WMP32G for stable cutting edge Consistent cutting performance for rostfreier Stahl The combination of Tiger·tec Gold coating and coated carbide substrate provides a balance of oxidation resistance and wear protection that benefits machining of rostfreier Stahl. The grade is formulated for medium to robust cutting conditions and supports stable chip formation, reducing the risk of built-up edge and thermal softening at the cutting zone. For production environments seeking repeatable results, this insert offers improved edge life and consistent surface quality without the need for frequent index changes. Secure chip control reduces interruptions Equipped with the IR3.5ISO chipbreaker, the insert promotes controlled, short to medium chips suitable for turning operations in rostfreie materials. Reduced erratic chip behaviour lowers the likelihood of tool damage and machine stoppages, contributing to higher net productive time. Process reliability improves with predictable chip flow, which in turn simplifies fixture and coolant strategy planning and supports higher feed choices when process windows allow. Practical advantages for workshop productivity The graded WMP32G substrate supports robust edge integrity, which is particularly valuable in incremental production and batch turning of rostfreier Stahl. The insert’s specification facilitates easier tool management—fewer indexes per component and longer service intervals—so operational throughput benefits directly. In systems-focused terms, the use of a coated carbide insert with a dedicated chipbreaker aligns with process-optimised workflows, delivering measurable gains in productivity and consistent component finish. Contact Metav Werkzeuge for tailored application support on the Walter Tools Tiger·tec Gold WMP32G insert — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: TS22-IR3.5ISO-WMP32G-WALTER Article: TS22-IR3.5ISO WMP32G Brand: Walter Tools Product type: Indexable turning insert Facts Grade: WMP32G Series: Tiger·tec Gold Chipbreaker: IR3.5ISO Material group: M (rostfreier Stahl) Special features Coated carbide construction Optimised for rostfreier Stahl machining Designed for secure chip formation and stable cutting edge FAQ What materials is this insert intended for? The TS22-IR3.5ISO WMP32G insert by Walter Tools is intended primarily for rostfreier Stahl (material group M) and is formulated to handle the toughness and heat characteristics of those alloys. Which chipbreaker is fitted and what benefit does it provide? The insert uses the IR3.5ISO chipbreaker, which supports secure chip control and reduced built-up edge when turning rostfreier Stahl with the WMP32G grade. How does the Tiger·tec Gold coating affect performance? The Tiger·tec Gold coating on the WMP32G grade improves wear resistance and thermal stability, contributing to longer edge life and more consistent machining results in demanding stainless applications. Is this insert suitable for high-feed turning strategies? The WMP32G grade and IR3.5ISO geometry support improved process stability; suitability for high-feed strategies depends on machine rigidity and cutting parameters but the combination is engineered to allow productive cutting windows. Can the insert be used in interrupted cuts or unstable conditions? The coated carbide construction and robust grade composition enhance resistance to edge chipping, making the insert appropriate for medium to robust conditions, including many interrupted cut scenarios. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners; brand names are used for clarification only. There is no affiliation between our company and the trademark owners; the listed item is an original, factory-new product of the manufacturer.
TS22-IR4.0ISO WMP22G Wendeplatten - Walter Tools
TS22-IR4.0ISO WMP22G – Drehwendeschneidplatte von Walter Tools TS22-IR4.0ISO WMP22G für präzise Dreharbeiten an rostfreien Stählen, entwickelt für stabile Spanbildung und hohe Prozesssicherheit TS22-IR4.0ISO WMP22G von Walter Tools Tiger‑tec Gold Beschichtung für lange Standzeit IR4.0ISO Spanformer für sichere Spanbildung Speziell für rostfreie Stähle (Werkstoffgruppe M) Hohe Prozesssicherheit bei robusten Einsatzbedingungen Produktivität und Standzeit erhöhen mit moderner Beschichtung Mit der Tiger‑tec Gold Beschichtung liefert diese Wendeschneidplatte eine Kombination aus guter Verschleißfestigkeit und optimierter Reibungscharakteristik. Anwender profitieren von längeren Standzeiten und stabilen Schneidkanten, was Rüstzeiten reduziert und die Nutzzeit an der Maschine erhöht. Die beschichtetes Hartmetall-Sorte WMP22G ist auf mittlere bis robuste Einsatzbedingungen ausgelegt und unterstützt eine konstante Bearbeitungsleistung. Sichere Spanbildung bei anspruchsvollen Werkstoffen Die Geometrie mit dem IR4.0ISO Spanformer ist speziell auf die Herausforderungen von rostfreien Stählen ausgelegt. Dadurch entsteht eine kontrollierte Spanform, die Aufbauschneiden reduziert und die Wärmeentwicklung an der Schneidkante verringert. Für Anwender heißt das: weniger Nacharbeit, gleichmäßigere Oberflächenqualität und eine zuverlässigere Prozessstabilität bei Serienfertigung. Technische Erklärung der wichtigsten Begriffe Für weniger erfahrene Nutzer: Spanformer bezeichnet die Bodenform der Wendeplatte, die den Span bricht und ableitet; ein gut ausgelegter Spanformer sorgt für kontinuierlichen Spanabfluss. Beschichtetes Hartmetall bedeutet, dass das Grundsubstrat aus Hartmetall besteht und eine dünne Funktionsschicht aufgebracht wurde, die Verschleiß und Reibung mindert. Diese Kombination macht die Platte praxistauglich für anspruchsvolle Drehanwendungen. Zielgruppe und typische Anwendungen Entwickelt für Anwender in der Metallzerspanung, die rostfreie Stähle bearbeiten, eignet sich die Platte für Produktionsumgebungen mit mittleren bis robusten Schnittbedingungen. Typische Einsatzfelder sind Umformtechnik, Maschinenbau und Komponentenfertigung, wo konstante Qualität und reproduzierbare Standzeiten gefragt sind. Die Sorte richtet sich an Fertiger, die Prozesssicherheit und Produktivität in den Vordergrund stellen. Setzen Sie auf die Tiger‑tec Gold Sorte WMP22G für zuverlässige Bearbeitung von rostfreien Stählen; Bestellbar über Metav Werkzeuge – technische Beratung per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: TS22-IR4.0ISO-WMP22G-WALTER Marke: Walter Tools Serie: Tiger-tec Gold Sorte: WMP22G Spanformer: IR4.0ISO Produkttyp: Drehwendeschneidplatte Daten Besonderheiten Schneidstoff: beschichtetes Hartmetall Bearbeitbar: rostfreie Stähle (Werkstoffgruppe M) Sortenbeschreibung: WMP22G gehört zur Tiger·tec Gold Beschichtungstechnologie Spanformer: IR4.0ISO (optimiert für sichere Spanbildung) Hohe Prozesssicherheit FAQ Welche Werkstoffe lassen sich mit dieser Wendeschneidplatte bearbeiten? Die Wendeschneidplatte von Walter Tools in der Sorte WMP22G ist speziell für rostfreie Stähle (Werkstoffgruppe M) ausgelegt und unterstützt dort sichere Spanbildung und stabile Schneidkanten. Was bedeutet Tiger‑tec Gold für die Praxis? Tiger‑tec Gold beschreibt die Beschichtungstechnologie der WMP22G Sorte; sie verbessert die Verschleißfestigkeit und reduziert Reibung, was zu längeren Standzeiten und höherer Produktivität bei der Bearbeitung führt. Für welche Einsatzbedingungen ist der IR4.0ISO Spanformer geeignet? Der IR4.0ISO Spanformer ist auf mittlere bis robuste Schnittbedingungen ausgelegt und sorgt für kontrollierten Spanabfluss bei zähen, wärmeanfälligen Werkstoffen wie rostfreien Stählen. Ist diese Platte für Serieneinsatz geeignet? Ja, die Kombination aus WMP22G Schneidstoff und Tiger‑tec Gold Beschichtung zielt auf konstante Performance und Prozesssicherheit, weshalb sie sich für Serieneinsätze in der Fertigung eignet. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
TS22-IR4.0ISO WMP32G Wendeplatten - Walter Tools
TS22-IR4.0ISO WMP32G — Drehwendeschneidplatte (Walter Tools) TS22-IR4.0ISO WMP32G ist eine Drehwendeschneidplatte für die produktive Bearbeitung von rostfreiem Stahl und ausgelegt auf mittlere bis robuste Schnittbedingungen TS22-IR4.0ISO WMP32G von Walter Tools Tiger·tec Gold Beschichtung für lange Standzeit Entwickelt für rostfreie Stähle, stabile Spanbildung IR4.0ISO Spanbrecher für sichere Spanabfuhr Beschichtetes Hartmetall für wiederholgenaue Performance Überzeugende Prozesssicherheit und messbare Wirtschaftlichkeit Prozesssicherheit steht im Mittelpunkt bei der Tiger·tec Gold Technologie. Die Wendeschneidplatte setzt auf eine beschichtete Hartmetall‑Sorte, die speziell für die Herausforderungen bei der Bearbeitung von rostfreiem Stahl optimiert ist. Diese Kombination reduziert Ausfallzeiten durch stabilere Schneidkanten und trägt zur gleichmäßigen Spanbildung bei. Anwender profitieren von konstanter Bearbeitungsqualität und höherer Teileausbeute, was sich direkt in reduzierten Stückkosten und verbesserter Maschinenauslastung niederschlägt. Spezielles Design für rostfreie Stähle und sichere Spanbildung Herausforderungen wie Zähigkeit, Aufbauschneiden und hohe Wärmeentwicklung sind typische Eigenschaften bei rostfreien Stählen. Die WMP32G Sorte bietet gezielte Materialeigenschaften, die diese Probleme mindern: bessere Spankontrolle und verringerte Neigung zu Aufbauschneiden. Durch den IR4.0ISO Spanbrecher wird die Spanabfuhr verbessert und die Schnittstabilität erhöht. Für Anwender bedeutet das weniger Nacharbeit, gleichmäßigere Oberflächen und zuverlässigere Serienläufe. Zielgruppengerechte Anwendung in Produktion und Lohnfertigung Serienfertiger, Lohnbearbeiter und Bearbeitungszentren, die regelmäßig rostfreien Stahl bearbeiten, erhalten mit diesem Schneidstoff eine wirtschaftliche Lösung. Die Platte eignet sich besonders dort, wo konstante Ergebnisse und lange Werkzeugstandzeiten gefragt sind. Durch die optimierte Beschichtung und die Sortenwahl wird die Prozesssicherheit erhöht, was insbesondere in hochvolumigen Produktionen zu planbarerer Ausbringung und weniger Maschinenstopps führt. Werkzeughandling und Integration in Produktionsprozesse Indexierbare Wendeschneidplatten bieten schnellen Wechsel und geringe Stillstandszeiten, was den Gesamtdurchsatz steigert. Die beschichtete Hartmetall Ausführung der Platte erlaubt eine einfache Integration in bestehende Werkzeughalter und Bearbeitungsstrategien, ohne aufwendige Anpassungen. Bei Bedarf steht gezielte technische Beratung für Schnittwerte und Werkzeugaufnahmen zur Verfügung, um die Produktivität weiter zu optimieren. Setzen Sie auf die Tiger·tec Gold Sorte WMP32G von Walter Tools für zuverlässige, wirtschaftliche Bearbeitung von rostfreiem Stahl — Beratung und Lieferung durch Metav Werkzeuge, eMail info@metav-werkzeuge.com, Telefon +49 2822 7131930 Produktmerkmale Artikelnummer: TS22-IR4.0ISO-WMP32G-WALTER Marke: Walter Tools Serie: Tiger-tec Gold Typ: Drehwendeschneidplatte Sorte: WMP32G Daten Besonderheiten Beschichtungstechnologie: Tiger·tec Gold Schneidstoffklasse: beschichtetes Hartmetall Spanbrecher: IR4.0ISO Bearbeitbar: rostfreie Stähle (ISO M) Sorteneinsatz: mittlere bis robuste Einsatzbedingungen FAQ Für welche Werkstoffe ist die Wendeschneidplatte geeignet? Die Wendeschneidplatte TS22-IR4.0ISO WMP32G von Walter Tools ist speziell für die Bearbeitung von rostfreien Stählen ausgelegt und unterstützt mittlere bis robuste Schnittbedingungen durch optimierte Spanbildung. Welche Vorteile bietet die Tiger·tec Gold Beschichtung? Die Tiger·tec Gold Beschichtung in der WMP32G Sorte sorgt für bessere Standzeit und stabile Schneidkanten, wodurch die Walter Tools Wendeschneidplatte gleichmäßigere Oberflächen und geringeren Werkzeugverschleiß liefert. Wie beeinflusst der IR4.0ISO Spanbrecher die Bearbeitung? Der IR4.0ISO Spanbrecher fördert kurze, kontrollierte Späne und reduziert Aufbauschneiden, was besonders bei zähen Werkstoffen wie rostfreiem Stahl die Prozessstabilität der TS22-IR4.0ISO WMP32G erhöht. Eignet sich die Sorte für Serienfertigung? Ja, die WMP32G Sorte ist für Serienfertigung mit gleichbleibenden Anforderungen an Präzision und Standzeit entwickelt worden und wird von vielen Herstellern wegen ihrer Wirtschaftlichkeit geschätzt. Welche Rolle spielt die Schneidstoffklasse für die Performance? Die Einstufung als beschichtetes Hartmetall signalisiert gute Verschleißfestigkeit und Temperaturbeständigkeit, was bei der Bearbeitung von rostfreiem Stahl zu konstanteren Ergebnissen mit der TS22-IR4.0ISO WMP32G führt. Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik-Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
TS22-IR4.0TR WMP32G WMP32G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold coating and the WMP32G grade combined with the IR4.0TR chipbreaker for stable edge life and dependable chip control when machining stainless steel; order the insert directly via Metav Werkzeuge or consult our application specialists for process optimisation. TS22-IR4.0TR WMP32G indexable turning insert — Tiger·tec Gold, IR4.0TR chipbreaker (Walter Tools) The TS22-IR4.0TR WMP32G is an indexable turning insert designed for demanding stainless steel turning where consistent edge stability and secure chip formation are required. Tiger·tec Gold coating for improved wear resistance WMP32G grade for stainless steel machining IR4.0TR chipbreaker for reliable chip control Consistent edge life for medium to heavy cuts Precise wear management for stainless steel turning Turning stainless steel presents specific challenges such as work hardening and built-up edge; the combination of the Tiger·tec Gold coating and the WMP32G coated carbide grade reduces flank and crater wear, which translates into fewer indexings and longer uninterrupted production runs. The coating technology enhances heat resistance and adhesion properties at the cutting edge, so the insert sustains cutting performance under elevated temperatures. This results in a tangible improvement in process reliability and cycle stability for serial machining operations. Secure chip control that stabilises cycle times The integrated IR4.0TR chipbreaker is engineered to produce predictable, controllable chip forms in medium to robust cutting conditions. Improved chip control reduces the risk of chip entanglement, minimises secondary operations for chip clearing and helps maintain a consistent surface finish on the workpiece. For production environments where repeatability matters, the chipbreaker supports steady material evacuation and lowers the likelihood of unplanned stoppages, ultimately contributing to higher overall equipment effectiveness. Productivity advantages through predictable tool life By combining a modern coated carbide grade with an optimised chipbreaker geometry, the insert delivers a favourable balance between tool life and cutting performance. The result is a more economical machining process: fewer tool exchanges, reduced setup interruptions and more predictable maintenance intervals. For plants processing stainless steel in batches or continuous shifts, this predictability supports capacity planning and reduces throughput variability while maintaining part quality. For availability and technical consultation on Walter Tools Tiger·tec Gold inserts for stainless steel, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 to discuss the TS22-IR4.0TR WMP32G and suitable cutting data Technical data Article number: TS22-IR4.0TR-WMP32G-WALTER Product type: Indexable turning insert Series: Tiger·tec Gold Grade: WMP32G Chipbreaker: IR4.0TR Material group: M (stainless steel) Manufacturer: Walter Tools Facts No dimensional data provided No tolerance class specified No corner radius specified Special features Coating: Tiger·tec Gold (coated carbide) Material: Coated carbide, grade WMP32G Application: stainless steel (ISO group M) Chipbreaker: IR4.0TR for stable chip formation Suitability: medium to robust cutting conditions FAQ What steels is this insert designed for? The TS22-IR4.0TR WMP32G indexable turning insert from Walter Tools is designed primarily for stainless steel (ISO group M) and performs well under medium to robust cutting conditions. How does the Tiger·tec Gold technology help in practice? Tiger·tec Gold coating on the WMP32G grade improves heat resistance and wear behaviour, so the insert maintains a stable cutting edge longer when machining stainless steel with frequent heat build-up. Which chip shape can be expected with the IR4.0TR breaker? The IR4.0TR chipbreaker is engineered to provide controllable, compact chips in turning operations, supporting cleaner evacuation and reduced machine downtime when using the TS22-IR4.0TR WMP32G insert. Is this insert suitable for heavy interrupted cuts? The WMP32G grade in the Tiger·tec Gold series is specified for medium to robust applications; for heavy interrupted cuts, the TS22-IR4.0TR WMP32G offers improved edge stability compared with conventional grades, but final suitability depends on the exact machining scenario and should be validated in-process. Can the insert's performance be optimised for a specific stainless steel grade? Yes, cutting data and feed parameters can be adjusted to the specific stainless steel grade; the TS22-IR4.0TR WMP32G is intended to provide a balance of wear resistance and chip control, and Walter Tools data sheets or Metav Werkzeuge consultants can recommend process parameters. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
TS22-IR4.5ISO WMP32G WMP32G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold wear resistance and the WMP32G grade for dependable machining of stainless steels; the IR4.5ISO chipbreaker stabilises chip flow and supports consistent surface quality—order directly via Metav Werkzeuge or request application advice from our consultants. TS22-IR4.5ISO WMP32G — indexable turning insert for stainless steels, Tiger·tec Gold (Walter Tools) The TS22-IR4.5ISO WMP32G is an indexable turning insert engineered for the reliable machining of stainless steels in moderate to robust cutting conditions, offering a balance of wear resistance and stable chip control. Tiger·tec Gold coating for enhanced wear resistance Optimised for stainless steel machining Stable chip formation under robust conditions Coated carbide grade WMP32G for extended tool life Higher process reliability through advanced coating and grade The combination of the Tiger·tec Gold coating and the WMP32G grade is designed to deliver consistent edge stability during longer cycles. The coating improves wear resistance at elevated temperatures commonly encountered when machining stainless steels, while the grade balances toughness and hardness to reduce edge chipping. This results in fewer unscheduled insert changes and more predictable tool life, which helps to increase machine uptime and reduce per-part tooling costs. Consistent surface finish thanks to controlled chip formation The integrated IR4.5ISO chipbreaker promotes organised chip formation and evacuation when cutting materials in the ISO M group. By avoiding long, stringy chips and reducing the tendency to form a built-up edge, the insert supports a repeatable surface quality and lowers the risk of workpiece rework. For operators and process planners, this translates into fewer interruptions and more reproducible part tolerances across batch runs. Suited to moderate and robust cutting conditions for stainless steels Specifically developed for the challenges of machining stainless steels, the insert copes with high work-hardening and heat generation. The WMP32G grade provides a compromise between toughness and wear resistance that is well suited to the M material group, enabling safe chip control and a stable cutting edge even under robust cutting parameters. This makes the insert appropriate for components where material ductility and heat build-up would otherwise shorten tool life. Straightforward integration and predictable performance in turning systems Designed as an indexable turning solution, the insert fits standard toolholder systems and delivers repeatable performance across shifts and batches. The predictable wear pattern of the coated grade simplifies inventory planning and helps to standardise production results. Backed by the Walter Tools pedigree, the insert supports process consistency and can be specified where a reliable balance of productivity and surface integrity is required. Contact Metav Werkzeuge for tailored cutting recommendations on Walter Tools Tiger·tec Gold inserts and ensure optimal processing of stainless steels—call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data Article number: TS22-IR4.5ISO-WMP32G-WALTER Product type: Indexable turning insert Designation: TS22-IR4.5ISO WMP32G Manufacturer: Walter Tools Facts Material group: M (stainless steels) Grade: WMP32G Chipbreaker: IR4.5ISO Special features Series: Tiger·tec Gold Coating: coated cemented carbide Application: machining of stainless steels under moderate to robust conditions FAQ What materials is this insert intended for? The TS22-IR4.5ISO WMP32G is intended for the ISO M material group and is optimised for machining stainless steels. How does the IR4.5ISO chipbreaker help in production? The IR4.5ISO chipbreaker promotes organised chip formation and evacuation with the WMP32G grade, improving surface finish consistency and reducing the risk of built-up edge. Can this insert be used at higher cutting speeds? The Tiger·tec Gold coating on the WMP32G grade improves wear resistance at elevated temperatures typical of stainless-steel machining; suitable cutting speeds should be selected according to machine capability and workpiece requirements. Is the insert compatible with standard toolholders? Yes, the indexable design is compatible with corresponding turning toolholders that accept the TS22 insert family and the specified ISO designation. What advantage does the Tiger·tec Gold series provide? The Tiger·tec Gold series offers improved wear resistance and edge stability, supporting longer effective tool life and more consistent production results with stainless steels. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen
TS22-IR5.0ISO WMP22G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, the WMP22G grade and the IR5.0ISO chipbreaker for reliable performance in rostfreier Stahl turning; order directly via Metav Werkzeuge or consult our experts for application-specific advice. TS22-IR5.0ISO WMP22G – Indexable turning insert for rostfreier Stahl by Walter Tools (Tiger·tec Gold) The TS22-IR5.0ISO WMP22G is an indexable turning insert engineered for turning rostfreier Stahl in medium to robust cutting conditions, offering secure chip control and stable cutting-edge performance. Tiger·tec Gold coated for high process security Grade WMP22G: coated carbide for rostfreier Stahl Stable chip formation under medium to robust conditions Reliable cutting-edge stability and good tool life Optimised coating and substrate for demanding rostfreier Stahl applications The insert employs the Tiger·tec Gold coating technology paired with the WMP22G coated-carbide grade to address the typical challenges of rostfreier Stahl machining, such as work hardening, built-up edge and elevated cutting temperatures. This combination promotes stable chip formation and reduces the tendency for adhesive wear, which translates into fewer unexpected interruptions and more consistent component quality. The material pairing is designed to maintain a reliable cutting edge under transient thermal and mechanical loads, supporting longer uninterrupted production cycles. Predictable machining behaviour and improved surface results The integrated IR5.0ISO chipbreaker is tuned to evacuate chips effectively in medium to robust feeds, helping to avoid chip entanglement and localised heat concentration. As a result, users can expect improved surface finish and reduced rework compared with unoptimised inserts. The insert’s construction fosters process security, permitting more stable cutting parameters and predictable tool-change intervals, which supports leaner planning and higher machine utilisation. Practical integration into indexable tool systems and clear material coding Designed as an indexable turning insert, this grade fits standard turning toolholders and can be incorporated into existing tooling strategies without major adjustments, aiding rapid implementation on the shop floor. The designation follows ISO coding: M (per ISO 513) indicates suitability for rostfreie Stähle, i.e. materials that demand a geometry and coating combination to control ductile chips and reduce workhardening. For production planners and operators, the clear material classification and the coated-carbide technology simplify grade selection and help achieve consistent component tolerances. Contact Metav Werkzeuge for tailored application advice and order availability of Walter Tools Tiger·tec Gold inserts; eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: TS22-IR5.0ISO-WMP22G-WALTER Description: TS22-IR5.0ISO WMP22G Grade: WMP22G Series: Tiger·tec Gold Manufacturer: Walter Tools Material group: M Facts ISO designation: TS22-IR5.0ISO Chipbreaker: IR5.0ISO Application group: M (rostfreie Stähle) Product type: Indexable turning insert Special features Coated carbide (Tiger·tec Gold technology) Optimised for rostfreier Stahl machining Stable chip formation and cutting-edge stability Suitable for medium to robust cutting conditions FAQ What materials is this insert intended for? The TS22-IR5.0ISO WMP22G is specified for rostfreie Stähle (ISO group M); the WMP22G grade supports safe chip formation and stable cutting edges in such materials. How does the IR5.0ISO chipbreaker affect machining? The IR5.0ISO chipbreaker promotes controlled chip evacuation under medium to robust feeds, reducing chip-related interruptions and improving surface quality when using the WMP22G insert. Can this insert be used with existing indexable holders? Yes, the insert is an indexable turning insert designed to integrate with standard holders, enabling straightforward replacement and fast implementation in production tooling systems. What are the main benefits of the Tiger·tec Gold technology on this insert? Tiger·tec Gold coating on the WMP22G grade enhances wear resistance and thermal stability, resulting in more consistent machining performance and extended tool life on rostfreie Stähle. Is this grade suitable for finishing or roughing operations? The WMP22G grade with IR5.0ISO is suitable for medium to robust cutting conditions, making it appropriate for both productive semi-finishing and robust finishing strategies depending on the chosen cutting data. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking. Protected trademarks and product names are the property of their respective owners. Brand names and proprietary product designations are used here for explanatory purposes only; there is no affiliation between Metav Werkzeuge and the trademark owners. The offered article is an original, factory-new product of the manufacturer.
TS22-IR5.0ISO WMP32G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, a dedicated IR5.0ISO chipbreaker and a grade tailored for machining stainless steel to secure stable chip formation and consistent surface quality. Order the insert directly via Metav Werkzeuge or ask the consultants for tailored cutting data and process recommendations. TS22-IR5.0ISO WMP32G — Indexable turning insert, Tiger·tec Gold grade for stainless steel (Walter Tools) The TS22-IR5.0ISO WMP32G is an indexable turning insert engineered for secure chip control and reliable cutting performance when machining stainless steel, offering a balance of edge stability and productivity in medium to robust cutting conditions. Tiger·tec Gold coated grade WMP32G Optimised for stainless steel (ISO M) IR5.0ISO chipbreaker for stable chips Robust edge for medium to heavy cuts Higher process stability through an optimised coated grade The WMP32G grade, part of the Tiger·tec Gold series, is a coated carbide designed specifically for the challenges of ISO M materials (rostfreier Stahl). Its multilayer coating supports stable cutting-edge behaviour and reduces the tendency for build-up on the cutting edge, which is common when machining tough, heat-sensitive stainless steels. This results in more predictable tool wear and fewer interruptions for edge dressing, directly supporting higher machine uptime and consistent part quality. Predictable chip control for better surface finish and safety The IR5.0ISO chipbreaker is tuned to produce short, controllable chips under a range of cutting conditions. Controlled chips minimise entanglement and improve evacuation from the cut, which contributes to a superior surface finish and reduces the risk of workpiece damage. For users with limited familiarity with chipformer geometry: the chipbreaker profile alters the metal flow at the cutting edge so that swarf breaks reliably into manageable segments rather than long, hazardous ribbons. Long tool life and economical productivity in demanding conditions Designed for medium to robust cutting, this insert supports a stable cutting edge under thermal and mechanical load. The combination of grade and chipbreaker helps maintain dimensional accuracy across longer tool life, which reduces the frequency of index changes and tool handling. For production environments, that means lower cycle interruptions and improved throughput. The insert’s focus on secure chip formation and edge stability makes it a practical choice where repeatable performance and process reliability are priorities. For machining rostfreier Stahl with high process reliability, contact Metav Werkzeuge to discuss specifying the Walter Tools TS22-IR5.0ISO WMP32G and to request personalised cutting parameters via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: TS22-IR5.0ISO-WMP32G-WALTER Product type: Indexable turning insert Designation: TS22-IR5.0ISO WMP32G Key figures ISO application group: M (stainless steel) Chipbreaker designation: IR5.0ISO Grade: WMP32G Materials & special features Series: Tiger·tec Gold Coating: Tiger·tec Gold (coated carbide) Suitable for: rostfreier Stahl (ISO M) Application: secure chip formation, medium to robust cutting conditions Manufacturer: Walter Tools FAQ What materials is this insert intended for? The TS22-IR5.0ISO WMP32G is optimised for rostfreier Stahl (stainless steel) and assigned to ISO group M for reliable machining of these materials. How does the IR5.0ISO chipbreaker affect performance? The IR5.0ISO chipbreaker promotes short, controlled chips to enhance chip control and minimise entanglement, improving surface finish and workplace safety when using the insert. Is the WMP32G grade suitable for heavy-duty turning? WMP32G is designed for medium to robust cutting conditions; its coated carbide formulation supports edge stability and consistent wear behaviour under demanding loads. Can this insert improve process reliability in production shops? Yes. The combination of the Tiger·tec Gold coating and the IR5.0ISO chipformer provides predictable tool life and stable cutting behaviour, which supports higher process reliability and throughput. Which series does this insert belong to and what is the benefit? The insert belongs to the Tiger·tec Gold series; this coating technology is chosen to maintain a stable cutting edge and improved resistance to build-up during stainless steel machining. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation. There is no affiliation between our company and the named brands. The offered item is an original, factory-new product from the manufacturer.
TS22-IR5.0TR WMP32G Wendeplatten - Walter Tools
TS22-IR5.0TR WMP32G Drehwendeschneidplatte von Walter Tools Die TS22-IR5.0TR WMP32G ist eine beschichtete Drehwendeschneidplatte für die prozesssichere Zerspanung von rostfreiem Stahl unter mittleren bis robusten Bedingungen. Tiger·tec Gold Beschichtung für stabile Schneidkante Optimierter IR5.0TR Spanbrecher für sichere Spanbildung Speziell für rostfreie Stähle ausgelegt Hohe Prozesssicherheit im Serienbetrieb Zuverlässige Standzeit und wiederholgenaue Performance Hohe Verschleißfestigkeit durch moderne Beschichtung Die Kombination aus Tiger·tec Gold Beschichtung und beschichtetem Hartmetall der Sorte WMP32G sorgt für eine deutlich verbesserte Verschleißfestigkeit. Anwender profitieren von einer langlebigen Schneidkante, die Aufbauschneiden reduziert und die Standzeit verlängert. Dadurch sinkt der Werkzeugwechselaufwand, und die Fertigungsanlage erreicht höhere Verfügbarkeit bei gleichbleibender Teilequalität. Verlässliche Spanbildung und bessere Oberflächen Der integrierte IR5.0TR Spanbrecher wurde für sichere Spanbildung bei rostfreien Stählen entwickelt. Eine kontrollierte Spanform minimiert Störungen am Werkstück und erleichtert die Spanabfuhr. Das Resultat ist eine stabilere Prozessführung und eine verbesserte Oberflächengüte bei Serienfertigung, was den Nachbearbeitungsaufwand reduziert. Entwickelt für industrielle Serienfertigung Diese Wendeschneidplatte richtet sich an Lohnfertiger und Serienproduzenten, die rostfreie Komponenten mit gleichbleibender Qualität bearbeiten. Die Sorte WMP32G unterstützt mittlere bis robuste Einsatzbedingungen und bietet konstante Ergebnisse auch bei anspruchsvollen Werkstoffen. Einsatzbereiche sind unter anderem Anlagenbau, Maschinenbau und Produktionslinien mit hoher Wiederholgenauigkeit. Einfache Einordnung und praxisnahe Anwendungshinweise Die Kennzeichnung M steht für rostfreie Stähle nach ISO und beschreibt die geeignete Werkstoffgruppe. Nutzer mit wenig Erfahrung erhalten so schnell Orientierung, welche Platte für ihren Einsatzzweck passt. Bei speziellen Schnittdaten oder besonderen Bauteilgeometrien empfiehlt sich die technische Abstimmung, damit die Platte ihr Potenzial voll entfalten kann. Für technische Beratung oder direkte Lieferanfragen zur TS22-IR5.0TR WMP32G empfiehlt sich die Kontaktaufnahme mit Metav Werkzeuge: eMail info@metav-werkzeuge.com oder Tel. +49 2822 7131930 Produktmerkmale Artikelnummer: TS22-IR5.0TR-WMP32G-WALTER Marke: Walter Tools Serie: Tiger-tec Gold Sorte: WMP32G Produkttyp: Drehwendeschneidplatte Spanbrecher: IR5.0TR Bezeichnung: TS22-IR5.0TR WMP32G Werkstoffkennzeichnung: M Fakten Besonderheiten Beschichtung: Tiger·tec Gold Schneidstoff: beschichtetes Hartmetall Bearbeitung: rostfreie Stähle (M: rostfreie Stähle) Spanformer: IR5.0TR Sorteneigenschaft: hohe Verschleißfestigkeit, stabile Spanbildung FAQ Für welche Werkstoffe ist die Wendeschneidplatte geeignet? Die TS22-IR5.0TR WMP32G von Walter Tools wurde für die Bearbeitung von rostfreien Stählen konzipiert und eignet sich besonders bei mittleren bis robusten Zerspanbedingungen. Welche Vorteile bietet die Tiger·tec Gold Beschichtung? Die Tiger·tec Gold Beschichtung der WMP32G sorgt für erhöhte Verschleißfestigkeit und stabile Schneidkanten, was in weniger Werkzeugwechseln und konstanter Bearbeitungsqualität resultiert. Wie unterstützt der IR5.0TR Spanbrecher die Fertigung? Der IR5.0TR Spanbrecher verbessert die Spanform und -abfuhr, reduziert Aufbauschneiden und trägt zu einer zuverlässigeren Serienfertigung mit besserer Oberflächengüte bei. Ist diese Platte für hochbeanspruchte Serienanwendungen geeignet? Ja, die Kombination aus Sorte WMP32G und Tiger·tec Gold macht die Wendeschneidplatte robust und prozesssicher für industrielle Serienanwendungen mit rostfreiem Stahl. Wen kontaktiere ich bei Fragen zu Schnittdaten oder Verfügbarkeit? Für Schnittdaten, Anwendungsberatung und Lieferfragen steht Metav Werkzeuge gern zur Verfügung; nutzen Sie die technischen Ansprechpartner per eMail oder Telefon. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Hersteller: Walter Tools
UX-12E1200N10-GD2 WKP33G Wendeplatten - Walter Tools
Taking advantage of Tiger·tec Gold grade and the WKP33G coating, the insert delivers reliable chip control and prolonged tool life in steel and cast iron machining; its coated carbide construction enables consistent wear resistance and process stability. Order the UX-12E1200N10-GD2 WKP33G indexable turning insert directly via Metav Werkzeuge or consult our specialists for application-specific advice. UX-12E1200N10-GD2 WKP33G indexable turning insert — Walter Tools (for steel and cast iron) UX-12E1200N10-GD2 WKP33G is an indexable turning insert designed for productive machining of steel and cast iron, utilising the Tiger·tec Gold coating technology from Walter Tools Tiger·tec Gold coating technology Optimised for steel and cast iron machining Coated carbide grade WKP33G for durability Stable chip formation and consistent wear Consistent performance through advanced coating and grade The combination of the Tiger·tec Gold coating and the WKP33G grade provides a measurable improvement in process reliability when turning a range of steels and cast irons. The coating is engineered to reduce abrasive wear and the substrate grade supports high thermal loads typical of these materials. As a result, the cutting edge sustains sharper geometry for longer, which reduces the need for frequent tool changes and contributes to uninterrupted production cycles. In practical terms, this means fewer interruptions and a steadier output quality during medium- to high-volume turning operations. Optimised chip control and machining stability Stable chip formation is achieved through the insert geometry and coated carbide construction, which together manage heat and fracture characteristics of steel and cast iron chips. The design minimises the risk of built-up edge and erratic spallation under catalogue-dependent geometries, so chip evacuation remains predictable. This stability supports consistent surface finishes and reliable dimensional repeatability, reducing rework and increasing throughput on lathes and CNC turning centres. The alloy and coating combination is specifically balanced for the thermal and mechanical demands of these workpiece groups. Practical advantages for production-oriented shops For production-oriented workshops, the insert offers a balance of wear resistance and edge robustness that suits both finishing and mixed turning tasks. The WKP33G sort is a coated cemented carbide developed to cover a broad material spectrum under typical cutting conditions for P (steel) and K (cast iron) classifications. Toolholders that accept the UX designation benefit from predictable insert replacement cycles and straightforward inventory management, which supports leaner tool provisioning and lower tooling overheads per component produced. Choosing the right application and expected outcomes When selecting the insert, consider the intended operation—light finishing, medium turning, or interrupted cuts—and match cutting parameters accordingly to leverage the coating’s strengths. The insert’s specification is particularly effective where abrasion from cast iron or heat generation from steel demands a wear-resistant edge. In these scenarios, users can expect improved surface quality and extended edge life, which together raise overall machining economy and process repeatability. Contact Metav Werkzeuge for tailored application advice and a quotation for Walter Tools Tiger·tec Gold inserts — Metav Werkzeuge can provide practical recommendations for cutting data and toolholder compatibility Technical data SKU: UX-12E1200N10-GD2-WKP33G-WALTER Product type: Indexable turning insert Manufacturer: Walter Tools ISO designation: UX-12E1200N10-GD2 WKP33G Material compatibility Steel (P) Cast iron (K) Coated cemented carbide grade WKP33G Special features Tiger·tec Gold series Coated cemented carbide construction Engineered for stable chip formation and wear resistance Suitable for catalogue-dependent geometries and typical turning applications FAQ What materials is this insert suitable for? The UX-12E1200N10-GD2 WKP33G insert from Walter Tools is intended for machining steel and cast iron, corresponding to ISO groups P and K. What benefits does the Tiger·tec Gold coating provide? Tiger·tec Gold on the WKP33G grade enhances wear resistance and thermal stability, allowing the Walter Tools insert to maintain cutting-edge integrity under the heat and abrasion typical of steel and cast iron turning. Is this insert suitable for finishing and medium turning? Yes, the coated carbide grade and geometry are designed to perform well in finishing and mixed turning tasks, offering a balance between surface quality and tool life. How does the insert improve chip control? The combination of geometry and coating promotes predictable chip breakage and evacuation, resulting in consistent chip flow and reduced risk of chip-related interruptions during machining. Which product designation should be used when ordering or specifying? Specify the SKU UX-12E1200N10-GD2-WKP33G-WALTER or the ISO designation UX-12E1200N10-GD2 WKP33G when ordering to ensure the correct Walter Tools Tiger·tec Gold insert is supplied. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are used for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered article is original, factory-new merchandise of the manufacturer Walter Tools. The Walter Tools brand is part of global precision tooling offerings and is referenced here solely to describe the product.
UX-19E1900N15-GD2 WKP33G Wendeplatten - Walter Tools
Take advantage of the proven combination of Tiger·tec Gold coating and the WKP33G grade for consistently productive turning of steel and cast iron; order directly via Metav Werkzeuge or ask the consultants for application advice. UX-19E1900N15-GD2 WKP33G – Turning indexable insert, Tiger·tec Gold (Walter Tools) A UX-19E1900N15-GD2 WKP33G indexable insert designed for high-productivity turning applications on steel and cast iron, offering reliable chip control and extended tool life Tiger·tec Gold coating for extended tool life WKP33G grade optimised for steel and cast iron Consistent chip control for productive turning Coated carbide for stable cutting performance Increased productivity through advanced coating and grade The combination of Tiger·tec Gold coating and the WKP33G carbide grade delivers measurable benefits in daily production: improved wear resistance and higher permissible cutting speeds reduce tool changes and machine idle time. The coating technology is engineered to lower adhesive wear and to preserve the cutting edge under thermal stress, which results in longer tool life and fewer interruptions. For operations where cycle time and repeatability matter, this configuration supports a steady production flow while maintaining component quality. Predictable chip formation and machining stability A primary advantage of this insert family is stable chip control, achieved through geometry and a dedicated chipbreaker designation. Stable chips minimise the risk of tool breakage and reduce the need for manual intervention at the machine, contributing to safer and more efficient turning cycles. The insert’s geometry supports continuous chip evacuation, which benefits finishing operations by reducing chatter and improving surface integrity; this leads to consistent dimensional results and a lower rejection rate. Clear application scope and guidance for workshop use The insert is specified for machining groups P and K according to ISO 513, meaning suitability for steel (P) and cast iron (K). For users less familiar with classification: P indicates unalloyed and alloyed steels with typical heat generation during cutting, while K refers to abrasive cast materials that tend to break into shorter chips. Selection of the UX-19E1900N15-GD2 variant in WKP33G supports both groups, enabling versatile use across mixed production lots and reducing tool inventory complexity when switching between materials. Request application support or sample advice from Metav Werkzeuge for Walter Tools Tiger·tec Gold inserts; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: UX-19E1900N15-GD2-WKP33G-WALTER SKU: UX-19E1900N15-GD2-WKP33G-WALTER Product type: Drehwendeschneidplatte (turning indexable insert) Designation: UX-19E1900N15-GD2 Full designation: UX-19E1900N15-GD2 WKP33G Grade: WKP33G Series: Tiger-tec Gold Material group: P / K Manufacturer: Walter Tools Facts No measurable numerical data provided in the source Special features Coating: Tiger·tec Gold Carbide type: coated hard metal (WKP33G) Chipbreaker: 19E1900N15-GD2 Suitable for machining: steel (P) and cast iron (K) Series description included: Tiger·tec Gold; WKP33G is a coated carbide grade optimised for steel and cast iron according to ISO 513 FAQ What materials is this insert suitable for? The UX-19E1900N15-GD2 WKP33G insert from Walter Tools is suitable for steel (material group P) and cast iron (material group K) as specified under ISO 513. How does the Tiger·tec Gold coating benefit production? The Tiger·tec Gold coating on the WKP33G grade reduces adhesive wear and improves thermal resistance, so the insert sustains cutting performance longer and supports increased machining speeds with consistent results. What is the role of the listed chipbreaker 19E1900N15-GD2? The chipbreaker geometry identified as 19E1900N15-GD2 promotes stable chip formation, improving evacuation and reducing the likelihood of built-up edge, which enhances process reliability when using the Walter Tools insert. Can this insert reduce tool inventory complexity? Yes. The multi-material suitability of the WX-19E1900N15-GD2 WKP33G variant allows consolidation of tools for mixed production runs, helping to reduce the number of different inserts required for both steel and cast iron components. Is this an original factory-new insert from the manufacturer? The UX-19E1900N15-GD2 WKP33G is offered as an original factory-new insert from Walter Tools, supplied with the specifications stated. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and brand names are the property of their respective owners. Brand names and trademarks are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered item is an original, factory-new product from the manufacturer. The Walter AG (brand: Walter Tools) is part of the Sandvik Group.
VBGT110302-FL2 WPP20G FL2 Wendeplatten - Walter Tools
Take advantage of a universal steel-grade insert with Tiger·tec Gold coating and a precision FL2 chipformer to keep turning operations consistent and productive; the result is reliable surface quality and extended tool life. Order through Metav Werkzeuge or request cutting-data and application advice from our consultants. VBGT110302-FL2 WPP20G – indexable turning insert for steel machining, Tiger·tec Gold, Walter Tools A VBGT110302-FL2 WPP20G indexable turning insert designed for steel (ISO P) turning applications, combining a universal wear-grade with a chipformer optimised for stable machining. Tiger·tec Gold coating for extended tool life Optimised FL2 chipformer for consistent chips Rhombic 35° geometry for versatile turning Universal grade WPP20G for steel (ISO P) Higher productivity through a universal, wear-resistant grade The solid benefit of the Tiger·tec Gold family is a predictable balance of wear resistance and toughness; the WPP20G grade is formulated for steel machining (ISO P) and performs across typical production conditions. That material balance reduces downtime for tool changes and stabilises cycle times, which directly supports higher machine utilisation. In practice, the coated carbide substrate and modern coating stack are the technical basis for improved tool life and consistent performance in repetitive turning tasks. Consistent chip control and improved surface finishes Reliable chip evacuation is essential for unattended operations and repeatable surface quality. The FL2 chipformer is engineered to produce predictable, segmented chips when cutting steels, lowering the risk of entanglement and easing chip handling. Combined with the Rhombus 35° geometry and a small 0.2 mm corner radius, the insert delivers fine finishing capability while maintaining edge stability—helpful for both light finishing cuts and medium-depth turning. The 5° relief angle supports clearance and reduces rubbing on the flank, optimising the cutting conditions. Stable economics and process security for production A focus on rational efficiency: fewer insert changes and fewer surface rejects mean reduced per-part machining costs. The coated grade and geometry deliver stable edge behaviour, which in turn reduces variance in batch production and supports predictable regrinding or replacement intervals. The Walter Tools heritage in precision tooling underpins the insert’s suitability for series work where process security and repeatability are critical; this contributes to lower overall operating costs and a clearer return on tooling investment. Practical fitment and selection guidance for workshops The insert uses the common VBGT form factor and fits standard toolholders designed for rhombic 35° turning inserts. Key dimensional cues—an inscribed circle of 11 mm and a thickness code 03—help to ensure compatibility with existing toolholders. When selecting an insert, consider the workpiece steel grade and cutting parameters: the universal WPP20G is intended as a go-to option for a wide range of steels, reducing the need for frequent grade swaps. For optimised parameters and holder matching, Metav Werkzeuge can supply cutting data and recommendations to suit the application. Contact Metav Werkzeuge for application-specific cutting data and to discuss how the Walter Tools Tiger·tec Gold VBGT110302-FL2 WPP20G insert can increase uptime in steel turning operations: info@metav-werkzeuge.com, +49 2822 7131930 Technical Data Article number: VBGT110302-FL2-WPP20G-WALTER Label: Drehwendeschneidplatte VBGT110302-FL2 WPP20G Walter Tools Manufacturer: Walter Tools Product type: indexable turning insert Grade: WPP20G Core data Relief angle: 5° Corner radius: 0.2 mm Inscribed circle: 11 mm Thickness code: 03 Tolerance class: G Geometry: Rhombus 35° Special features Coating: Tiger·tec Gold Chipformer: FL2 Suitable for: steel (ISO P) Series: Tiger·tec Gold Material code: P Execution: T FAQ What materials is the VBGT110302-FL2 WPP20G best suited for? The VBGT110302-FL2 WPP20G is optimised for steel (ISO P) machining and is intended as a universal grade within the Tiger·tec Gold family for a broad range of unalloyed and alloyed steels. How does the FL2 chipformer affect machining stability? The FL2 chipformer on the VBGT110302-FL2 WPP20G produces predictable chip shapes that improve evacuation and reduce the risk of chip build-up, supporting stable, unattended turning cycles with Walter Tools inserts. What edge preparation and finish can be expected with this insert? With a 0.2 mm corner radius and Rhombus 35° geometry, the insert delivers good surface finishes in finishing to medium-turning applications while maintaining edge robustness under typical steel cutting conditions. Which toolholders are compatible with this insert form? Standard toolholders designed for the VBGT/Rhombus 35° insert family accept the VBGT110302-FL2 WPP20G; compatibility depends on inscribed circle and clamping style—match the 11 mm inscribed circle and thickness code 03 when selecting holders. Where can cutting data and application advice be obtained? Cutting parameters and holder recommendations for the VBGT110302-FL2 WPP20G are available from Metav Werkzeuge; technical guidance helps to tailor speeds, feeds and approach for specific steel grades. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are used for explanation only; there is no affiliation implied between Metav Werkzeuge and those manufacturers. The offered item is an original, factory-new product from the stated manufacturer.
VBGT110302-FL2 WSM01 FL2 Wendeplatten - Walter Tools
Take advantage of the combination of high process security, coated carbide performance and precise geometry for consistent turning results; order directly via Metav Werkzeuge or ask their consultants for application advice. VBGT110302-FL2 WSM01 — indexable turning insert, coated carbide, rhombic 35° (Walter Tools) The VBGT110302-FL2 WSM01 is a coated carbide turning insert developed for robust machining of stainless steels and heat‑resistant superalloys, delivering reliable chip control in demanding turning operations. Tiger‑tec Silver series coated carbide For stainless steels and superalloys Rhombic 35° geometry, 5° clearance FL2 chipbreaker, 0.2 mm nose radius Productive machining for demanding materials The WSM01 grade within the Tiger‑tec Silver family is a coated carbide solution optimised for tough-to-cut groups defined by ISO. Designed to manage the high temperatures and adhesive tendencies of stainless steels and the poor thermal conductivity of superalloys, the insert supports stable cutting edge performance and extended tool life. The coated surface reduces wear rates while maintaining cutting-edge integrity, which helps to lower process costs through fewer tool changes and more predictable component quality. Geometry that secures surface finish and chip control The insert’s rhombic 35° outline and 5° clearance produce an effective cutting geometry that balances strength and accessibility in confined tool holders. The 0.2 mm nose radius contributes to improved surface finish without sacrificing robustness at the cutting edge, while the FL2 chipbreaker is tuned to generate short, controllable chips under a range of cutting conditions. Together these features reduce vibration, support consistent material removal and make it easier to achieve repeatable tolerances in serial production. Application guidance and process integration Marked for ISO groups S and M, this grade is suitable for machining demanding alloys and stainless steels in medium to finishing operations where process security and surface quality are priorities. The insert’s tolerance class G and standard indexable format simplify inventory management and tool setup in mixed-production environments. If additional selection support or cutting data are required, Metav Werkzeuge’s technical consultants can provide tailored recommendations by material and machining strategy; contact via info@metav-werkzeuge.com or +49 2822 7131930. The Walter AG (brand: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Contact Metav Werkzeuge for application advice and precise ordering of Walter Tools Tiger‑tec Silver inserts via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: VBGT110302-FL2-WSM01-WALTER Designation: VBGT110302-FL2 WSM01 Manufacturer: Walter Tools Series: Tiger‑tec Silver Core specifications Size: 11 Thickness code: 03 Nose radius: 0.2 mm Relief angle: 5° Geometry: Rhombus 35° Tolerance class: G Grade: WSM01 Materials & features Coated carbide FL2 chipbreaker Suitable for stainless steels (ISO M) Suitable for heat‑resistant superalloys and titanium (ISO S) Material groups: S / M FAQ What materials is this insert suited to machine? The insert is designed for machining stainless steels and heat‑resistant superalloys (ISO M and S) in demanding turning applications; the WSM01 grade supports secure chip formation and edge stability. How does the FL2 chipbreaker affect performance? The FL2 chipbreaker produces short, controlled chips and reduces the risk of long, entangling swarf, improving process reliability when using the VBGT110302-FL2 WSM01 insert. Which operations benefit most from this insert geometry? The rhombic 35° form with 0.2 mm nose radius and 5° clearance is particularly useful for medium to finishing turning where surface quality and dimensional repeatability are required. Is the insert part of a recognised series or coating family? Yes, the insert belongs to the Tiger‑tec Silver series and uses a coated carbide grade WSM01 formulated for high process security and stable performance. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
VBGT110304-FL2 WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of the WPP20G coated grade, FL2 chipbreaker and the rhombic geometry for consistent steel turning; this ensures stable chip formation and predictable tool life. Order the insert directly via Metav Werkzeuge or consult our advisors for application-specific suggestions. VBGT110304-FL2 VBGT110304-FL2 WPP20G – turning insert for steel by Walter Tools VBGT110304-FL2 WPP20G is an indexable turning insert designed for efficient machining of steel, combining a coated carbide grade with a dedicated chipbreaker and rhombic geometry for reliable performance in production environments. Tiger·tec Gold coating for stable cutting edge WPP20G grade optimised for steel machining FL2 chipbreaker for reliable chip control Rhombic 35° shape with 0.4 mm nose radius Consistent performance for steel turning The WPP20G cutting grade, integrated in the Tiger·tec Gold family, is formulated for the thermal and mechanical demands of steel machining. The coated-carbide construction gives a balance between wear resistance and toughness, so the insert maintains a stable cutting edge under typical turning conditions. For operations that prioritise process reliability, the combination of coating technology and the specified geometry reduces unexpected downtime and supports steady cycle times. Predictable chip control and surface quality Equipped with the FL2 chipbreaker and a rhombic 35° profile, this insert promotes segmented, controllable chips and helps avoid long stringy chips that complicate handling. The 0.4 mm nose radius delivers a compromise between edge strength and achievable surface finish, enabling good part quality without sacrificing durability. These design decisions translate into fewer interruptions for chip clearing and more consistent workpiece surfaces in serial turning. Easy integration into productive toolsets The insert’s ISO-style designation and standard geometry facilitate quick selection and fitting into common turning tool holders. The clearance angle of 5° supports a robust cutting edge while minimising rubbing and heat build-up. As an indexable insert intended for steel applications, it works well in workshops aiming to streamline tool changes and maintain high machine uptime, supporting efficient setup and reproducible results across shifts. Practical advantages for workshop planning Choosing this grade reduces the need for frequent regrinds and trial runs: the coated carbide and chipbreaker are engineered for broad applicability across unalloyed and alloyed steels. The tolerance class G and the standardised plate dimensions make stock management and tool planning straightforward. For production managers, the result is a measurable improvement in operational predictability and a smoother transition from prototype to series production. Contact Metav Werkzeuge today to discuss Walter Tools Tiger·tec Gold inserts and secure the optimal WPP20G grade for steel machining; call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data SKU: VBGT110304-FL2-WPP20G-WALTER Article name: Drehwendeschneidplatte VBGT110304-FL2 WPP20G Walter Tools Manufacturer: Walter Tools Product type: turning insert (indexable) Grade: WPP20G Series: Tiger·tec Gold Facts Clearance angle: 5° Nose radius: 0.4 mm Plate form: Rhombus 35° Plate size: 11 Plate thickness: 03 Tolerance class: G Special features Chipbreaker: FL2 Coating: Tiger·tec Gold (coated carbide) Material application: Steel (P) Execution: T Designation without grade: VBGT110304-FL2 FAQ What materials is this insert suitable for? The VBGT110304-FL2 WPP20G insert is designed specifically for steel (ISO group P); the WPP20G grade and Tiger·tec Gold coating are optimised for typical heat and chip characteristics of steel turning. How does the FL2 chipbreaker affect machining? The FL2 chipbreaker on this insert promotes controlled chip formation and easier chip evacuation, which reduces interruptions and supports consistent surface quality during turning operations. Can this insert be indexed to use multiple edges? Yes, the VBGT110304-FL2 WPP20G is an indexable turning insert; rotating to a fresh cutting edge is standard practice to extend usable life and maintain machining stability. What surface finish can be expected with a 0.4 mm nose radius? A 0.4 mm nose radius provides a balance of strength and finish: it yields good surface quality on turned parts while offering enhanced edge robustness for longer tool life. Is this insert compatible with standard tool holders for rhombic 35° plates? The insert follows common ISO-style geometry for rhombic 35° plates, making it compatible with standard holders designed for this plate form when the clamping system supports the VBGT designation. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany, info@walter-tools.com The Walter AG (brand: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and product names remain the property of their respective owners. The mentioned brand is named for explanatory purposes only; there is no affiliation between our company and the brand owner. The item offered is an original, factory-new product of the manufacturer.
VBGT110304-FL2 WSM01 WSM01 Wendeplatten - Walter Tools
Take advantage of the combination of a specialised WSM01 carbide grade, a precise rhombic 35° geometry and the FL2 chipbreaker to improve process stability and reduce interruptions in turning operations. Order directly via Metav Werkzeuge or request tailored application advice for integration into existing production lines. VBGT110304-FL2 WSM01 indexable turning insert, rhombic 35°, 5° relief — Walter Tools VBGT110304-FL2 WSM01 is an indexable turning insert designed for demanding machining of rostfreier Stahl and heat‑resistant alloys, offering a balance of edge stability and controlled chip formation Tiger‑tec Silver coated carbide grade WSM01 Optimised chip control with FL2 chipbreaker Suitable for rostfreier Stahl and superalloys Rhombic 35° form with 5° relief Durable grade for high‑temperature and tough alloys The WSM01 grade from the Tiger‑tec Silver series is a coated carbide formulation developed for machining challenging materials. Its composition prioritises heat resistance and stable edge behaviour, which helps to reduce build‑up and extend tool life when working with rostfreier Stahl and heat‑resistant superalloys. This results in fewer tool changes, more consistent component quality and a predictable process window, which is particularly valuable in production environments where downtime carries high cost. Geometry that supports precise, repeatable turning The rhombic 35° insert form paired with a 5° relief angle creates an effective compromise between approach angle and edge strength. The corner radius 0.4 mm helps to produce a good surface finish while maintaining cutting edge stability in interrupted cuts or varying engagement conditions. The insert size (11) and thickness code (03) provide a compact, robust working geometry that suits a wide range of turning tasks from light finishing to moderate cutting depths, enabling consistent part tolerances across batches. Chip control and process efficiency with FL2 The FL2 chipbreaker is engineered to promote short, controllable chips when cutting ductile and heat‑resistant materials, reducing the risk of entanglement and machine stoppages. Improved chip formation contributes directly to higher effective machining time and better surface integrity on the workpiece. In practice, this means more efficient cycle times and fewer production interruptions, so the operation benefits immediately from the insert’s optimised shape and coating. Practical integration and handling in the workshop The insert is intended for standard clamping into compatible turning toolholders and is designed to be indexed as each corner is used, supporting economical tooling strategies. Given the insert’s focus on rostfreier Stahl and superalloys, tool path planning and coolant strategy should be adapted to the workpiece material to exploit the grade’s heat‑tolerant properties. For detailed application settings and to ensure the best match with existing holders, Metav Werkzeuge can provide targeted recommendations and machining data on request. Contact Metav Werkzeuge for tailored application advice, sample availability and process recommendations — info@metav-werkzeuge.com, +49 2822 7131930 Technical data SKU: VBGT110304-FL2-WSM01-WALTER Designation: VBGT110304-FL2 WSM01 Series: Tiger‑tec Silver Grade: WSM01 Manufacturer: Walter Tools Facts Relief angle: 5° Corner radius: 0.4 mm Insert shape: Rhombic 35° Insert size: 11 Thickness code: 03 Tolerance class: G Special features Chipbreaker: FL2 Coating/material: coated carbide Suitable for: rostfreier Stahl (M), Superalloys / Titanium (S) Series characteristics: Tiger‑tec Silver Application: indexable turning operations FAQ What materials is this insert designed to machine? The VBGT110304‑FL2 WSM01 insert is optimised for rostfreier Stahl and heat‑resistant superalloys (ISO groups M and S), delivering stable cutting behaviour on challenging materials. How does the FL2 chipbreaker affect performance? The FL2 chipbreaker promotes short, manageable chips and supports consistent surface quality; with the WSM01 grade, this combination reduces built‑up edge and machine interruptions. Which geometry advantages does the rhombic 35° offer? The rhombic 35° form provides a versatile cutting angle that balances strength and accessibility, suited for a range of turning tasks and helping to maintain dimensional consistency. Is the insert suitable for finishing operations? Yes; the 0.4 mm corner radius and the coated carbide grade support good surface finishes in many finishing scenarios, provided feeds and speeds are adapted to the workpiece material. How should the insert be clamped and indexed? The insert is intended for use in standard turning toolholders supporting VBGT‑style inserts. Indexing the corners extends service life and improves cost efficiency. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
VBGW110304TM-2 WBH10 Wendeplatten - Walter Tools
Take advantage of the combination of CBN cutting performance and robust rhombic geometry for reliable hard-turning results; order the insert from Metav Werkzeuge or contact our consultants for application support. VBGW110304TM-2 WBH10 – Indexable turning insert for hard machining, Walter Tools The VBGW110304TM-2 WBH10 is an indexable turning insert designed for high-wear machining of hardened steels and comparable hard materials, offering a CBN grade for extended tool life and repeatable performance CBN grade WBH10 for hard machining Rhombic 35° geometry for versatile turning 5° clearance with 0.4 mm nose radius Suitable for hardened steels and pre-hardened materials Outstanding wear resistance for hard turning The CBN-based WBH10 grade delivers exceptional wear resistance where conventional carbides fail, specifically tailored for hardened steels and heavy-duty finishing operations. By using a cubic boron nitride cutting material, the insert sustains high temperatures and abrasive contact without rapid degradation, which means fewer tool changes and more consistent component quality. This results in a measurable increase in process stability and a reduction in unplanned downtime, making the component choice particularly effective for shops that process heat-treated workpieces or need repeatable batch results. Geometry that stabilises cutting and improves surface quality The rhombic 35° shape combined with a 5° clearance and 0.4 mm nose radius provides a balance between accessibility and cutting-edge strength. The slender approach of the rhombic geometry allows for versatile turning positions while the defined nose radius supports smooth transitions and improved surface finish on the workpiece. A moderate radius reduces cutting forces compared with larger radii and helps maintain dimensional accuracy in finishing passes. The insert’s tolerance class G underlines its suitability for precision tasks where repeatability is required. Practical benefits and application guidance This insert is part of the Walter CBN / Hartstoff series and includes an integrated chipbreaker 2, optimised for chip control in hard materials. For practical machining, the insert performs best at steady cutting conditions and is particularly effective in operations where abrasive wear dominates. Choosing a CBN grade minimises flank wear and thermal deformation, delivering a predictable tool life that supports production planning. Where material specifications indicate pre-hardened or hardened steel, this insert is a productive choice for finishing and semi-finishing cycles. For demanding hard-turning applications select the Walter Tools WBH10 CBN insert and request technical assistance from Metav Werkzeuge; contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored recommendations and availability. Technical Data Article number: VBGW110304TM-2-WBH10-WALTER Item designation: VBGW110304TM-2 WBH10 Product type: Indexable turning insert (Drehwendeschneidplatte) Series: Walter CBN / Hartstoff Facts Shape angle: Rhombus 35° Clearance angle: 5° Nose radius: 0.4 mm Plate size: 11 Thickness code: 03 Chipbreaker: 2 Tolerance class: G Special features Cutting material: CBN (WBH10) Intended for: Hardened steels / pre-hardened steel Application focus: Hard machining, finishing and semi-finishing Robust edge for high wear resistance FAQ What materials is this insert suitable for? The VBGW110304TM-2 WBH10 insert (Walter Tools, CBN grade) is intended for hardened steels and pre-hardened materials, offering high wear resistance in abrasive cutting conditions. How does the rhombic 35° shape affect machining? The rhombic 35° geometry enables flexible turning positions and good access to the workpiece while maintaining edge strength; it supports stable cutting and improved surface finish for finishing passes. Is the insert suitable for finishing operations? Yes, the CBN composition and the 0.4 mm nose radius of this insert make it particularly well suited for finishing and semi-finishing of hard components, delivering consistent surface quality. What does tolerance class G mean for production? Tolerance class G indicates a precise manufacturing tolerance of the insert, supporting repeatable seating and predictable part dimensions across insert indexings. Can this insert reduce tool change frequency? Due to the wear resistance of the WBH10 CBN grade, this insert typically extends tool life compared with carbide alternatives, which can reduce the frequency of tool changes in hard-machining applications. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names remain the property of their respective owners. Brand names are mentioned for clarification only and do not imply any affiliation with our company. The offered item is original, brand-new manufacturer product.
VBGW110304TM-2 WBH20 Wendeplatten - Walter Tools
Take advantage of the CBN-grade WBH20 for demanding hard-turning jobs and the stabilising rhombic 35° geometry with a 0.4 mm corner radius to secure consistent surface quality and prolonged edge life; order or request application advice via Metav Werkzeuge for a reliable production upgrade. VBGW110304TM-2 WBH20 indexable turning insert — Walter Tools, CBN grade for hard turning The VBGW110304TM-2 WBH20 is an indexable turning insert in rhombic 35° form, engineered for hard turning and robust performance when machining hardened steels. CBN grade WBH20 for hard turning Rhombic 35° geometry for versatile cuts 0.4 mm corner radius for precise finishing 5° relief angle with chipbreaker 2 Reliable cutting performance for hardened materials The insert combines a CBN cutting grade (WBH20) with a geometry tailored to hard machining, delivering high wear resistance and prolonged tool life. Cubic boron nitride is significantly harder than carbide and therefore maintains a stable cutting edge under the high temperatures and forces typical of hardened steel work. This results in fewer indexings, reduced tool change frequency and consequently higher component throughput — a clear efficiency advantage for production environments where uptime and repeatability matter. Geometry that enhances surface finish and chip control The rhombic 35° shape and 0.4 mm corner radius offer a balance between access to tight profiles and an appropriately small nose for fine finishing. The 5° relief angle reduces rubbing and improves shearing, while the integrated chipbreaker 2 promotes controlled chip formation even in demanding steels. Together these features support consistent surface quality and lower secondary finishing effort, which helps maintain cycle-time targets and reduces downstream processing. Application fit and material compatibility explained Designed for ISO group H applications, the grade is specifically specified for hardened steels and is suitable for pre-hardened material where wear resistance is essential. The WBH20 grade, part of the Walter CBN / Hartstoff series, is targeted at hard and strongly abrasive machining tasks; explanation of the term CBN clarifies why it is preferred for these applications — exceptional hardness and thermal stability compared with conventional carbides. For shops facing recurring hard turning or finishing of heat-treated components, the insert offers process security and predictable performance. Practical integration and production benefits With the designation VBGW110304TM-2 WBH20, the insert matches established tooling systems and inserts of similar numbering, enabling straightforward integration into existing toolholders. Its tolerance class G supports reproducible positioning and consistent clamping behaviour at changeovers. The nominal size value 11 and thickness 03 make it suitable for many standard turning bodies, while the combination of CBN grade and chip control reduces tool inventories through longer individual insert life. The result is a measurable reduction in downtime and an improvement in total machining economy. For tailored application advice on Walter Tools CBN inserts and to discuss compatibility with existing tooling, contact Metav Werkzeuge for precise recommendations and swift availability. Technical Data SKU: VBGW110304TM-2-WBH20-WALTER Designation: VBGW110304TM-2 WBH20 Manufacturer: Walter Tools Product type: indexable turning insert Series: Walter CBN / Hartstoff Core data Geometry: Rhombus 35° Size: 11 Thickness: 03 Corner radius: 0.4 mm Relief angle: 5° Chipbreaker: 2 Tolerance class: G Materials & features Cutting grade: CBN (WBH20) Suitable for: hardened steels (ISO group H) Intended use: hard turning, finishing of heat-treated components Execution: W FAQ What materials is this insert suitable for? The VBGW110304TM-2 WBH20 insert is intended primarily for hardened steels (ISO group H); the WBH20 CBN grade delivers wear resistance and edge stability for such applications. How does a CBN grade differ from carbide for turning tasks? CBN grades such as WBH20 provide higher hardness and thermal stability than carbide, which makes the insert better suited for hard turning and maintaining surface finish under elevated cutting temperatures. Can the insert be used in standard toolholders? Yes, the insert follows a familiar indexable geometry and sizing; the designation VBGW110304TM-2 corresponds to common toolholder interfaces, allowing straightforward integration with appropriate turning bodies. Which applications benefit most from this Walter Tools insert? Applications involving finishing or continuous turning of hardened and pre-hardened steels benefit most, where the WBH20 grade reduces tool change frequency and supports consistent part quality. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are used for explanatory purposes only and do not imply any affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
VBGW160402TM-2 WBH10 Wendeplatten - Walter Tools
The combination of a CBN grade WBH10 cutting edge and a rhombic 35° geometry delivers extended tool life and consistent chip control for hard-turning tasks; the precise 0.2 mm corner radius and 5° clearance angle further improve surface quality and dimensional stability. Order the insert directly via Metav Werkzeuge or contact the consultants for application support. VBGW160402TM-2 WBH10 – Indexable turning insert, CBN grade, rhombic 35° by Walter Tools The VBGW160402TM-2 WBH10 is a CBN indexable turning insert engineered for hard machining and finishing of hardened steels. CBN grade WBH10 for hard-turning tasks Rhombic 35° geometry for versatile cutting 0.2 mm corner radius for fine turning accuracy 5° clearance angle for secure chip formation Improved productivity for hard machining The use of CBN (cubic boron nitride) in the WBH10 grade provides outstanding wear resistance when machining high‑hardness materials. This grade is tailored to sustain cutting edges under elevated temperatures and abrasive contact, which directly reduces tool change frequency and machine downtime. As a result, process stability is enhanced and production output becomes more predictable. The combination of a wear‑resistant cutting substrate and stable geometry supports cost efficiency over long production runs while maintaining repeatable performance on tough workpieces. Consistent surface finish through precise edge geometry The insert’s rhombic 35° shape and 0.2 mm corner radius are designed to balance cutting strength with the capability to achieve fine surface finishes. A smaller corner radius supports accurate dimensional control on turned parts, while the 5° clearance angle prevents rubbing and reduces built-up edge formation. The integrated chipbreaker 2 promotes controlled chip segmentation, which simplifies chip evacuation and protects the cutting edge. These features together help to deliver uniform part quality in finishing passes and in operations where tight tolerances are required. Practical application and material suitability Specified for the ISO 513 group H, this insert is particularly suited to hardened steels and pre‑hardened materials, making it appropriate for hard‑turning and finishing of quenched components. The insert’s dimensions — 16 mm nominal size and 4 mm thickness — plus a tolerance class G provide a predictable fit and repeatability in modern toolholders designed for indexable inserts. The series classification indicates suitability for demanding, high‑wear tasks where consistent cutting performance is essential. For setup, cutting data should be matched to machine rigidity and workpiece condition to fully exploit the advantages of the WBH10 grade. For demanding hard‑turning applications, specify the Walter Tools CBN grade WBH10 insert and consult Metav Werkzeuge for machining recommendations and availability; Metav Werkzeuge can be reached via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: VBGW160402TM-2-WBH10-WALTER Designation: VBGW160402TM-2 WBH10 Product type: Indexable turning insert Brand: Walter Tools Core specifications Size: 16 mm Thickness: 4 mm Corner radius: 0.2 mm Clearance angle: 5° Plate form: Rhombic 35° Tolerance class: G Materials & features Grade: WBH10 (CBN) Series: Walter CBN / Hard material Suitable for: hardened steels (ISO 513 group H) Applicable to pre‑hardened steel Chipbreaker: 2 FAQ Which materials is this insert designed for? The VBGW160402TM-2 WBH10 insert by Walter Tools is designed primarily for hardened steels (ISO 513 group H) and is suitable for pre‑hardened components where a CBN grade provides the required wear resistance. How does the 0.2 mm corner radius affect the turned surface? A 0.2 mm corner radius on the Walter Tools insert promotes improved dimensional control and a finer surface finish during finishing operations, while maintaining sufficient edge strength for stable cuts. What advantages does the WBH10 CBN grade offer compared with conventional carbides? The WBH10 CBN grade maintains edge integrity at elevated temperatures and against abrasive wear, which results in longer tool life and more consistent process stability compared with conventional carbide grades in hard‑turning applications. What role does the chipbreaker 2 play in machining? Chipbreaker 2 provides defined chip control for segmented chips, reducing the risk of long swarf and improving chip evacuation, which contributes to safer, cleaner operation and prolonged cutting performance with the Walter Tools insert. What tolerance and form specifications apply to this insert? The insert is supplied with tolerance class G and a rhombic 35° plate form, offering predictable fitment and suitable geometry for a range of turning operations. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (marketed as Walter Tools) is among the world’s leading manufacturers of precision cutting tools for metalworking and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners and are mentioned here for explanatory purposes only. There is no affiliation implied between Metav Werkzeuge and these trademark owners. The described article is an original, factory‑new product from the manufacturer.
VBGW160402TM-2 WBH20 Wendeplatten - Walter Tools
Take advantage of the combination of extreme wear resistance, precise geometry and stable chip control for consistent hard-turning productivity. The CBN-based WBH20 grade and the Rhombic 35° form ensure long tool life and reliable surface quality under high contact stresses—order directly via Metav Werkzeuge or consult our specialists for application-specific cutting data. VBGW160402TM-2 WBH20 indexable insert — CBN grade for hard turning (Walter Tools) The VBGW160402TM-2 WBH20 is an indexable insert engineered for heavy-duty hard turning of hardened steels and other high-wear materials, combining a CBN cutting grade with a geometry optimised for stable cutting and repeatable results. CBN grade WBH20 for hardened steels Rhombic 35° form for versatile turning 5° clearance for reduced rubbing 0.2 mm corner radius for stable edge Consistent performance for hard finishing and long tool life The CBN-based WBH20 grade delivers very high wear resistance, designed specifically for machining hardened steels where conventional carbide grades wear quickly. The CBN substrate keeps the cutting edge stable at elevated temperatures and under heavy contact pressures, which translates into longer tool life and fewer insert changes. This stability benefits batch operations and rework-prone components by reducing variability and maintaining surface integrity during extended cycles. Geometry that improves process security and surface quality The Rhombic 35° shape combined with a 5° clearance and a 0.2 mm corner radius provides a balanced cutting geometry: radial strength for interrupted cuts, a cutting angle suited to axial and facing operations, and an edge form that supports controlled micro‑chipping rather than catastrophic failure. The insert dimensions (16 mm inscribed size, 4.0 mm thickness) make it suitable for a broad range of toolholders and turning conditions, while the integrated chipbreaker promotes predictable chip formation, lowering the risk of built-up edge and improving finished-surface consistency. Application focus and process advice for reliable integration This insert is intended for hard turning and finishing of pre‑hardened and hardened steels, delivering stable performance in demanding production environments. Adoption of CBN inserts typically allows higher cutting speeds or increased metal removal rates compared with wear-limited alternatives; however, emphasis should be placed on secure clamping, correct coolant and parameter selection to exploit the grade’s advantages. For tailored cutting data, batch optimisation or verification in a specific machine setup, Metav Werkzeuge provides application support and cutting-parameter guidance to ensure efficient integration into existing processes. Contact Metav Werkzeuge for application-specific cutting data and availability; email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt technical advice and delivery options Technical data Article number: VBGW160402TM-2-WBH20-WALTER Article designation: VBGW160402TM-2 WBH20 Manufacturer: Walter Tools Series: Walter CBN / Hartstoff Facts Insert form: Rhombus 35° Inscribed size: 16 mm Thickness: 4.0 mm Clearance angle: 5° Corner radius: 0.2 mm Chipbreaker: 2 Tolerance class: G Execution: W Special features CBN cutting grade for hard materials Suitable for hardened steel and pre‑hardened steel machining Stable edge for high wear resistance Series optimised for hard turning and demanding applications FAQ What materials is this insert suitable for? The VBGW160402TM-2 WBH20 insert is specified for hardened steels and pre‑hardened steel applications and performs reliably in hard-turning scenarios. How does the CBN grade affect tool life? The CBN cutting material in the WBH20 grade offers superior wear resistance under high temperature and pressure, extending tool life and reducing insert changes compared with conventional carbide grades. Which geometry advantages does the Rhombic 35° provide? The Rhombic 35° form offers versatility for axial and radial turning, improved accessibility in tight contours and balanced strength that supports interrupted and continuous cuts. Is this insert compatible with standard indexable turning toolholders? The insert’s 16 mm inscribed size and common Rhombic form make it compatible with many standard toolholders designed for this format; matching the seat and clamping style remains essential. Does the insert require special cooling or clamping measures? While the WBH20 grade tolerates higher temperatures, secure clamping and appropriate coolant strategies are recommended to maximise edge life and maintain process stability. Protected trademarks and trade names are the property of their respective owners. Brand names are cited solely for explanation. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer Walter Tools. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
VBGW160404TM-2 WBH10 Wendeplatten - Walter Tools
High process security and extended tool life result from the combination of the CBN cutting material WBH10 and the Rhombic 35° geometry with a 0.4 mm corner radius; the design is tailored for demanding hard-turning tasks. Order the VBGW160404TM-2 WBH10 indexable turning insert directly via Metav Werkzeuge or consult the technical team for application advice. VBGW160404TM-2 WBH10 – Indexable turning insert, CBN grade, Rhombic 35° – Walter Tools The VBGW160404TM-2 WBH10 is an indexable turning insert engineered for hard turning and the machining of hardened steels, delivering wear resistance and stable chip control. CBN grade WBH10 for hard turning Rhombic 35° geometry for versatile operations 0.4 mm corner radius for fine surface finish 5° relief angle for reliable chip control Reliable wear resistance for hard materials The combination of a CBN cutting material and the Walter CBN / Hartstoff series provides high wear resistance when machining hardened components. Designed specifically for the ISO group H (hardened steels), the grade WBH10 offers a consistently stable cutting edge under elevated contact pressures, which reduces flank wear and keeps component dimensions within tolerance for longer production runs. This contributes directly to improved process economy by lowering tool-change frequency and minimising unplanned downtime. Geometry that enhances surface quality and process stability The Rhombic 35° insert geometry and a 0.4 mm corner radius support both finishing and semi-finishing passes with predictable cutting behaviour. The relatively small corner radius helps to achieve fine surface finishes while limiting cutting forces, and the 5° relief angle reduces rubbing on the flank face, improving dimensional stability. A defined chipbreaker configuration (chipbreaker 2) aids in forming short, controllable chips during interrupted and continuous cuts, which supports automated operations and simpler chip handling. Application range and integration into production This indexable insert is optimised for hard turning tasks including the machining of hardened steels and pre-hardened components. The designation VBGW160404TM-2 WBH10 identifies the insert geometry and core dimensions, enabling straightforward selection of compatible toolholders. Using a CBN grade reduces sensitivity to abrasive wear typical of hardened alloys and cast components, allowing maintenance of tight surface roughness targets and dimensional tolerances across series production. Process planners will find the insert particularly suitable where repeatability and long tool life are priorities. For demanding hard-turning operations select the Walter Tools VBGW160404TM-2 WBH10 and contact Metav Werkzeuge for tailored process support and ordering at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: VBGW160404TM-2-WBH10-WALTER Type designation: VBGW160404TM-2 WBH10 Manufacturer: Walter Tools Facts Relief angle: 5° Corner radius: 0.4 mm Inscribed circle / size: 16 mm Thickness: 04 Tolerance class: G Chipbreaker: 2 Special features Grade: WBH10 (CBN) Geometry: Rhombus 35° Series: Walter CBN / Hartstoff Execution: W Suitable for: hardened steels (ISO group H), pre-hardened steel Product type: indexable turning insert FAQ Is this insert suitable for machining hardened steels? Yes. The VBGW160404TM-2 WBH10 is specifically designed for ISO group H and pre-hardened steel applications, using a CBN grade formulated for hard turning. What does the WBH10 grade indicate? WBH10 is a Walter CBN cutting-material grade optimised for high wear resistance and stability in hard machining tasks, especially for hardened steels and similar demanding materials. Which operations benefit most from the Rhombic 35° geometry? Rhombic 35° geometry is well suited to versatile turning applications, including close-tolerance finishing and semi-finishing where access and approach angles require a compact insert shape. How does the 0.4 mm corner radius affect surface finish? A 0.4 mm corner radius helps achieve finer surface finishes while moderating cutting forces; it is a compromise between edge strength and achievable roughness in finishing passes. Can this insert be used with standard VBGW toolholders? Yes. The VBGW160404TM-2 WBH10 designation corresponds to standard VBGW seating and can be integrated into toolholders designed for that insert form, ensuring secure clamping and repeatable positioning. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no affiliation between Metav Werkzeuge and the named brands. The offered article is an original, factory-new product of the manufacturer.
VBGW160404TM-2 WBH20 Wendeplatten - Walter Tools
Take advantage of the combination of high process reliability, long tool life and precise edge stability for efficient hard-turning operations; order directly via Metav Werkzeuge or consult the team for application support. VBGW160404TM-2 WBH20 indexable turning insert — CBN grade, Rhombic 35° (Walter Tools) The VBGW160404TM-2 WBH20 is a CBN-grade indexable turning insert designed for hard and wear-intensive turning tasks, offering a 35° rhombic geometry and a small corner radius for precise finishes CBN grade for hard materials Rhombic 35° insert geometry 0.4 mm corner radius for precision 5° clearance angle for stable cutting Maximised throughput for hard machining The CBN composition of this grade delivers exceptional wear resistance and lifetime stability when machining hardened steel and similar hard materials. Cubic boron nitride is a superabrasive optimised for high-temperature, high-pressure cutting, which translates into fewer index changes and longer productive tool life. Paired with the Rhombic 35° geometry, the insert enables stable engagement and consistent chip control, so cycle times are reduced and uptime increases. The result is a measurable improvement in process reliability and overall machining economy. Consistent edge strength and surface quality A 0.4 mm corner radius balances edge robustness with the ability to achieve tight dimensional control and a fine surface finish. The modest radius increases the strength of the cutting edge under heavy loads, lowering the risk of edge chipping during interrupted cuts. Together with the 5° clearance angle, the insert maintains a stable cutting line and predictable wear behaviour, simplifying tool-path programming and post-process inspection. This combination supports repeatable component quality, especially in series production of hardened parts. Application guidance and material compatibility Marked for hard turning, the grade WBH20 from the Walter CBN range is primarily intended for hardened steels and can be applied to pre-hardened materials as indicated. Depending on the workpiece alloy and process parameters, the grade may also be considered for demanding cast or superalloy tasks where wear is dominant. The insert is supplied in the VBGW160404TM-2 format suitable for holders accepting a Rhombic 35° insert form; confirm holder compatibility prior to use. For tailored cutting data, insert seating and optimal speeds for specific batches of hardened steel, contact Metav Werkzeuge by e‑mail or phone for precise recommendations. For demanding hard-turning applications, contact Metav Werkzeuge for availability and expert application advice on the Walter Tools VBGW160404TM-2 WBH20 indexable turning insert. Technical data Article number: VBGW160404TM-2-WBH20-WALTER SKU: VBGW160404TM-2-WBH20-WALTER Label: Drehwendeschneidplatte VBGW160404TM-2 WBH20 Walter Tools Facts Clearance angle: 5° Corner radius: 0.4 mm Insert size: 16 mm Thickness: 0.4 mm Shape: Rhombic 35° Chipbreaker: 2 Tolerance class: G Special features Grade: WBH20 (CBN cutting material) Series: Walter CBN / hard material Format: VBGW160404TM-2 Execution: W Material suitability: hardened steel, pre-hardened steel Recommended use: hard turning, wear-intensive operations FAQ Which materials is this insert mainly suitable for? The VBGW160404TM-2 WBH20 insert is primarily suitable for hardened steels and pre-hardened materials, reflecting the CBN grade’s focus on wear-resistant, hard turning tasks. What does the WBH20 designation mean for performance? WBH20 is a Walter CBN grade engineered for stable cutting and high wear resistance; users of the VBGW160404TM-2 WBH20 can expect extended edge life in demanding hard-machining applications. How does the 0.4 mm corner radius affect part quality? A 0.4 mm corner radius provides a compromise between edge strength and precision, improving robustness during heavy cuts while enabling a high-quality surface finish on turned components. Is the insert compatible with standard rhombic 35° holders? The insert is supplied in a VBGW format with Rhombic 35° geometry; it fits holders designed for that insert form—verify holder compatibility before mounting. Can this insert be used for interrupted cuts or roughing operations? The CBN composition and the 0.4 mm corner radius give the insert good resistance to wear and edge damage, making it suitable for demanding interrupted or roughing operations on hardened materials, within the constraints of machine and process parameters. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only. There is no affiliation between our company and the brands named. The offered item is an original, factory-new product of the manufacturer.
VBGW160404TM-2 WBH20C Wendeplatten - Walter Tools
Take advantage of the high wear resistance of the CBN grade and the controlled chip management from the rhombic 35° geometry to improve cycle stability and reduce tool changes; order the insert directly via Metav Werkzeuge or contact our consultants for process advice. VBGW160404TM-2 WBH20C indexable turning insert — CBN grade, rhombic 35°, Walter Tools VBGW160404TM-2 WBH20C is a rhombic 35° indexable insert engineered for hard turning and heavy-duty finishing of hardened steels. Walter CBN grade WBH20C for hard materials Rhombus 35° geometry for versatile turning 0.4 mm corner radius for reliable edge strength 5° clearance angle for controlled chip flow Robust wear resistance for hard turning applications The insert VBGW160404TM-2 WBH20C is produced in a CBN-based grade specifically developed for severe wear conditions encountered in the machining of hardened steels. Cubic boron nitride provides a stable cutting edge at elevated temperatures and under high contact pressures, which translates into a longer effective tool life and fewer tool changes per shift. This stability supports consistent cycle times and reduces unexpected stoppages, making the component a rational choice where process reliability and repeatability are priorities. Geometry that supports chip control and surface quality With a rhombic 35° form, a 0.4 mm corner radius and a 5° clearance angle, the geometry promotes controlled engagement and predictable chip flow. The defined corner radius increases edge strength for interrupted cuts while the modest clearance angle helps maintain a stable cutting contact to reduce vibration. The integrated chipbreaker 2 assists in producing shorter, manageable chips and contributes to improved surface finish, lowering the need for secondary operations and enhancing overall process efficiency. Designed for productive, reproducible machining The combination of a CBN cutting material and precise geometry delivers measurable productivity benefits: higher material removal rates in hard-turning tasks and reduced tooling costs via extended insert life. The insert’s classification and tolerance align with industrial expectations for repeatable performance, which supports planning and tool inventory management. For production environments where cycle consistency and predictable consumable behaviour are essential, this solution offers a clear cost-benefit through reduced downtime and stable product quality. Practical handling and application notes The insert is supplied in the Walter CBN / Hartstoff series and is intended for machining pre-hardened and hardened steels according to the material group designation. Mounting in standard compatible toolholders with the corresponding pocket geometry yields secure clamping and correct rake/clearance orientation. The tolerance class contributes to interchangeability across assemblies. For application-specific suggestions, including recommended feed and depth strategies for different hardness levels, technical consultation is available to align machining parameters with shop-floor realities. For tailored advice on integrating Walter Tools CBN inserts into production and to check immediate availability, contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 — our specialists will advise on the best process settings and delivery options Technical data SKU: VBGW160404TM-2-WBH20C-WALTER Designation: VBGW160404TM-2 WBH20C Product type: indexable turning insert Brand: Walter Tools Core measurements Insert size: 16 Corner radius: 0.4 mm Clearance angle: 5° Thickness code: 04 Chipbreaker: 2 Tolerance class: G Design & features Series: Walter CBN / Hartstoff Grade: WBH20C (CBN-containing cutting material) Geometry: Rhombus 35° Execution: W Suitable for: hardened and pre-hardened steels FAQ What materials is this insert suitable for? This indexable insert is designed primarily for hardened and pre-hardened steels; the CBN grade WBH20C gives the insert high resistance to abrasive wear when machining hardened materials. How does the rhombic 35° geometry affect cutting performance? The rhombic 35° shape offers a versatile cutting edge that balances access and strength, and when paired with the 0.4 mm corner radius it provides stable performance for both finishing and more demanding interrupted turning operations. Is this insert compatible with standard toolholders? Yes, the VBGW160404TM-2 WBH20C is intended for use in toolholders compatible with the specified indexable insert form and size; correct pocket fit and clamping ensure consistent cutting geometry. What benefit does the WBH20C grade give compared with conventional grades? The WBH20C grade, containing CBN, significantly improves edge retention and thermal resistance in hard-turning tasks, leading to extended tool life and steadier machining performance under high contact loads. Can this insert be used on castings or non-ferrous alloys? The insert is optimised for hard and pre-hardened steels; alternative grades should be selected for cast irons or non-ferrous alloys to achieve optimal chip formation and tool life. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only and do not imply any affiliation between our company and the named brands. The offered article is an original, factory-new product of the manufacturer.
VBGW160404TM-2 WBH30 Wendeplatten - Walter Tools
Take advantage of the CBN-grade WBH30 and the rhombic 35° geometry to secure stable performance when machining hardened components; the combination of wear resistance and a 0.4 mm corner radius yields consistent surface quality and longer effective tool life. Order the insert directly via Metav Werkzeuge or consult their specialists for application advice and supply. VBGW160404TM-2 WBH30 indexable turning insert — CBN grade, rhombus 35° by Walter Tools VBGW160404TM-2 WBH30 is a rhombic 35° indexable turning insert designed for hard machining and finishing of hardened steels in demanding production environments CBN grade WBH30 for hard machining Rhombus 35° geometry for versatile turning 0.4 mm corner radius for improved surface finish 5° clearance angle for cutting stability Long-life CBN for demanding hard turning The WBH30 cutting grade employs CBN (cubic boron nitride), a material engineered for high wear resistance and thermal stability in hard machining. This insert is intended for operations where standard carbide grades would wear prematurely; the CBN matrix maintains edge integrity under high contact stresses and elevated temperatures, enabling longer production runs and reduced tool change frequency. The result is improved machining economy through fewer interruptions and predictable tool-life cycles. Geometry tuned for repeatable surface quality A rhombic 35° form with a 0.4 mm corner radius and a 5° clearance angle balances strength and finish capability. The acute rhombic lead provides access to narrow profiles and shoulder work, while the modest corner radius supports fine surface results without sacrificing edge robustness. The defined geometry reduces vibration and stabilises chip flow, which leads to consistent dimensional accuracy and improved workpiece appearance on serial production parts. Application range and process reliability Designed within the Walter CBN / Hartstoff series, the insert is specifically matched to ISO group H applications — that is, hardened steels and pre‑hardened components. The integrated chipbreaker 2 controls fragmentation under heavy loads, helping to avoid built-up edge and to maintain a steady cutting force. This combination ensures process security and repeatability across workpieces made from high‑hardness alloys, castings, or quenched and tempered steels where wear resistance is critical. Practical integration into machining workflows The insert’s ISO designation supports a wide range of standard toolholders, allowing straightforward replacement in existing tool setups and minimal setup time. Consistent tolerances (class G) and the standardised plate format simplify inventory management and reordering. For shops aiming to increase throughput on hard turning operations, the insert offers a pragmatic balance of performance and predictability, reducing scrap risks and smoothing production planning. For genuine Walter Tools VBGW160404TM-2 WBH30 indexable inserts and tailored advice on hard turning applications, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and supply. Technical Data SKU: VBGW160404TM-2-WBH30-WALTER ISO designation: VBGW160404TM-2 WBH30 Series: Walter CBN / Hartstoff Grade: WBH30 Product type: Indexable turning insert Tolerance class: G Measurements and angles Size: 16 mm Thickness: 4 mm Corner radius: 0.4 mm Clearance angle: 5° Plate form: Rhombus 35° Chipbreaker: 2 Materials and special features Suitable for: hardened steels (ISO group H) Suitable for: pre-hardened steel Cutting material: CBN Series designation: Walter CBN / Hartstoff Execution: W FAQ What materials is this insert intended for? The VBGW160404TM-2 WBH30 insert by Walter Tools is intended primarily for hardened steels (ISO group H) and for pre‑hardened components where CBN grades deliver extended tool life. What does the WBH30 designation indicate? WBH30 denotes a Walter CBN cutting grade engineered for hard machining; the grade emphasises wear resistance and edge stability for demanding turning tasks. How does the rhombic 35° geometry benefit machining? The rhombic 35° form on this indexable turning insert allows access to tight profiles and shoulders, while the 0.4 mm corner radius and 5° clearance provide a compromise between robust cutting edges and fine surface finish. Which chip control is provided and why does it matter? This insert features chipbreaker 2, which helps to fragment and evacuate chips consistently under heavy cutting conditions, reducing the chance of re-cutting and improving process reliability. Is the insert compatible with standard holders for VBGW inserts? The ISO designation VBGW160404TM-2 indicates compatibility with the corresponding standard toolholders for VBGW inserts, allowing easy integration into established tool systems. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only; there is no connection between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer, Walter Tools.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com