WCGT030202-X15 WTP35 Wendeplatten - Walter Tools
Benefit from the combination of coated carbide durability, precise Trigon 80° geometry and the smoothing action of the X15 chipbreaker to support steady production cycles; order the WCGT030202-X15 WTP35 via Metav Werkzeuge or consult their specialists for tailored cutting data. WCGT030202-X15 WTP35 – Drilling/boring indexable insert, Trigon 80°, X15 chipbreaker (Walter Tools) A WCGT030202-X15 WTP35 indexable insert engineered for drilling and boring tasks, offering Trigon 80° geometry and a 0.2 mm corner radius for controlled cutting engagement Coated carbide WTP35 for reliable wear resistance Trigon 80° geometry for stable cutting engagement 0.2 mm corner radius for precise edge control 7° clearance angle reduces rubbing Consistent cutting performance through a wear-resistant grade The insert uses a coated carbide grade designed to deliver wear resistance and consistent edge life under cyclic loads. Coatings on modern inserts reduce adhesion and thermal wear; in practice this means more predictable tool life and fewer unplanned changeovers. For operations where component tolerance and hole integrity matter, the combination of a robust substrate and a functional coating contributes directly to repeatable results and lower overall machining costs. Geometry tuned for stability and hole quality The Trigon 80° shape, coupled with the X15 chipbreaker, is intended to improve entry conditions and control chip formation during drilling and boring operations. The 0.2 mm corner radius supports edge strength without sacrificing dimensional accuracy, reducing the risk of edge chipping when plunging into a workpiece. The chipbreaker’s geometry helps to generate short, controllable chips that reduce vibration and improve surface finish — a clear benefit for operations calling for consistent hole geometry. Productivity gains through optimised engagement and clearance A 7° clearance angle reduces rubbing on the flank face and helps maintain cutting temperatures within acceptable limits, supporting longer tool life and better surface integrity. The insert’s Trigon profile provides multiple usable cutting corners, which increases the usable lifespan per insert and reduces tooling costs per hole produced. These design choices aim to keep machining cycles efficient and downtimes minimal in high-throughput environments. Application advice and process integration Suitability for specific materials should be verified against the manufacturer’s product matrix before use; the grade is a coated carbide variety and is presented as a general-purpose solution for drilling/boring. When integrating into a tool holder or drilling head, ensure correct clamping and reference the insert orientation for the Trigon 80° seat. For unusual workpiece materials or demanding process windows, technical documentation and parameter sheets are recommended to establish optimal cutting speeds and feeds. Contact Metav Werkzeuge for tailored cutting data and application support for the WCGT030202-X15 WTP35; Metav Werkzeuge’s specialists can advise on suitable speeds, feeds and mounting recommendations to match production goals Technical data Article number: WCGT030202-X15-WTP35-WALTER Designation: WCGT030202-X15 WTP35 Brand: Walter Tools Type: Drilling/boring indexable insert Facts Corner radius: 0.2 mm Clearance angle: 7° Plate geometry: Trigon 80° Plate size: 03 Plate thickness: 02 Chipbreaker: X15 Tolerance class: G Special features Coated carbide grade WTP35 Series: Walter Schneidstoffsorte - Serie offen Execution: T Material specification: catalogue dependent Suitable for drilling and boring applications Walter engineering for process stability FAQ What materials is this insert suited to machine? Suitability depends on the specific application matrix; the WCGT030202-X15 WTP35 is a coated carbide grade intended as a versatile solution, and material compatibility should be confirmed with the manufacturer’s product matrix. How does the X15 chipbreaker affect chip control? The X15 chipbreaker produces short, controllable chips that reduce vibration and improve surface finish during drilling and boring, helping to maintain hole quality and operator safety. What is the benefit of the Trigon 80° geometry? Trigon 80° geometry offers stable cutting engagement with multiple usable corners per insert, which increases cutting economy and supports consistent hole dimensions in repetitive processes. Can the insert be indexed to extend life? Yes, the Trigon form provides several indexable corners; correct seating and clamping extend the insert’s usable life and reduce tooling expenditure per part. Where can cutting parameters for this insert be obtained? Cutting data and recommended speeds/feeds for the WCGT030202-X15 WTP35 are available from Metav Werkzeuge or the Walter Tools technical documentation for optimised process setup. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is original, factory-new goods of the manufacturer.
WCGT030202-X15 WXM15 Wendeplatten - Walter Tools
Take advantage of the combination of sharp edge geometry, predictable chip control and material‑specific performance to improve cycle times in non‑ferrous production. Order the insert via Metav Werkzeuge or contact the consultants for cutting data and clamping recommendations. WCGT030202-X15 WXM15 — drill/boring indexable insert by Walter Tools — for non‑ferrous metals The WCGT030202-X15 WXM15 is an indexable insert engineered for drilling and bore enlargement operations, optimised for machining non‑ferrous materials such as aluminium, copper and brass. Trigon 80° geometry for stable cutting Uncoated carbide grade for NE metals 0.2 mm corner radius for fine surface quality 7° clearance for reduced friction Reliable performance for non‑ferrous production The WXM15 grade is an uncoated carbide composition specifically intended for ISO group N materials, offering a very sharp cutting edge and low adhesion tendency. Combined with the Trigon 80° geometry and the X15 chipbreaker, the insert supports controlled chip formation and reduced built‑up edge during high‑feed drilling and enlargement operations. This leads to more consistent cycle times and fewer interruptions for manual cleaning, which improves overall process efficiency. Better surface finish with predictable tool behaviour A 0.2 mm corner radius and a 7° clearance angle create a balance between edge strength and surface integrity: the small radius refines the machined bore wall while the clearance minimises rubbing and thermal transfer. The result is a reproducible surface quality and lower rework rates. The precision of the insert’s tolerance class G and the stable seating provided by the Walter series ensure repeatable geometry from change to change, helping to maintain tight dimensional control in batch production. Practical integration and productive handling The insert is supplied in the Walter N‑Sortensystem and is designated with plate size 03 and thickness 02, enabling straightforward integration into holders designed for this system. The indexable insert format reduces downtime for tool changes and permits fast re‑orientation of cutting edges on multi‑point applications. With the chip control features of X15 and the uncoated edge shape, the component is particularly suitable for machining aluminium alloys and other soft, adhesive non‑ferrous materials where chip evacuation and surface appearance are important. Contact Metav Werkzeuge for tailored cutting data and prompt supply of the Walter Tools WCGT030202-X15 WXM15; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: WCGT030202-X15-WXM15-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WCGT030202-X15 WXM15 Walter Tools Manufacturer: Walter Tools Product type: drill/boring indexable insert Grade: WXM15 Series: Walter N‑Sortensystem Designation without grade: WCGT030202-X15 ISO designation: WCGT030202-X15 WXM15 Facts Geometry: Trigon 80° Clearance angle: 7° Corner radius: 0.2 mm Chipbreaker: X15 Plate size: 03 Thickness code: 02 Tolerance class: G Special features Uncoated carbide for non‑ferrous materials Optimised for ISO group N (aluminium, copper, brass) Stable chip control for adhesive materials Fast edge indexing in Walter N‑system Execution code: T FAQ Is this insert suitable for aluminium alloys? Yes. The WXM15 grade and the X15 chipbreaker are tailored for ISO group N materials, making the insert appropriate for a wide range of aluminium alloys and other non‑ferrous metals. What advantages does the Trigon 80° form bring to drilling operations? The Trigon 80° form provides a stable cutting geometry that improves entry behaviour and supports consistent chip formation during drilling and bore enlargement. How does the 0.2 mm corner radius affect surface finish? The small 0.2 mm corner radius helps to achieve finer surface quality while maintaining sufficient edge strength for repeatable bores with minimal rework. Can the insert be used in existing Walter N‑system holders? Yes. The insert is part of the Walter N‑Sortensystem and fits holders specified for the WCGT030202 series and corresponding plate size. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WCGT030202-X25 WK1 WK1 Wendeplatten - Walter Tools
Take advantage of the combination of uncoated carbide WK1, Trigon 80° geometry and the X25 chipbreaker for stable chip control and consistent tool life; order directly via Metav Werkzeuge or request application advice from the consultants. WCGT030202-X25 WK1 drill/bore indexable insert — Trigon 80°, 0.2 mm corner radius (Walter Tools) A WCGT030202-X25 WK1 drill/bore indexable insert engineered for precision metal cutting with Trigon 80° geometry and an X25 chipbreaker for controlled chip formation Trigon 80° geometry for secure seating Uncoated carbide grade WK1 for broad use 7° clearance angle for reliable chip control X25 chipbreaker for consistent chips Optimised geometry for increased process stability The combination of Trigon 80° geometry and a 0.2 mm corner radius provides a secure seat and predictable contact conditions at the cutting edge. This design reduces radial run-out and contributes to a more stable machining process, which in turn supports longer tool life and improved surface finish. The 7° clearance angle reduces friction at the flank face, improving heat evacuation and lowering the risk of built-up edge. As a result, operators benefit from fewer interruptions and more reproducible results in batch production. Consistent chip formation and material flexibility Manufactured in uncoated carbide (WK1) and equipped with the X25 chipbreaker, the insert promotes controlled chip segmentation and evacuation under typical drilling and boring conditions. The uncoated grade provides predictable wear behaviour and is suitable for a range of general machining tasks; the exact workpiece compatibility should be verified against the official product matrix. The insert thickness and size are designed for stable clamping in standard toolholders, offering a balance between cutting edge strength and accessibility in confined bores. Productivity through repeatable accuracy and simple handling With a tolerance class of G and a clear designation for series and execution, the insert supports consistent interchangeability and traceable process set-up. The Trigon form and the defined corner radius help to maintain dimensional integrity across tool changes, reducing calibration time and scrap rates. For production environments that prioritise uptime and predictable output, this indexable cutting insert delivers a combination of mechanical robustness and straightforward handling that contributes to overall shop-floor efficiency. Contact Metav Werkzeuge for tailored application advice on Walter Tools inserts or for ordering information via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: WCGT030202-X25-WK1-WALTER Product type: Drill/bore indexable insert Designation: WCGT030202-X25 WK1 Manufacturer: Walter Tools Data Plate form: Trigon 80° Clearance angle: 7° Corner radius: 0.2 mm Plate size: 03 Plate thickness: 02 Special features Grade: WK1 (uncoated carbide) Chipbreaker: X25 Series: Walter Schneidstoffsorte - Serie offen Execution: T Tolerance class: G Material specification: catalogue-dependent FAQ What materials is this insert suitable for? The WCGT030202-X25 WK1 insert is produced in the WK1 uncoated carbide grade; suitability for specific materials should be checked against the product matrix provided by Walter Tools. Does the insert require a special toolholder? Standard toolholders accepting Trigon 80° inserts are compatible; ensure the holder matches the listed plate size and thickness for correct clamping. How does the X25 chipbreaker affect performance? The X25 chipbreaker promotes predictable chip formation and evacuation, which supports stable cutting conditions and reduced risk of clogging during drilling or boring operations. Is the corner radius suitable for finishing operations? The 0.2 mm corner radius provides a compromise between edge strength and surface finish, making the insert suitable for semi-finish and many finishing tasks when process parameters are optimised. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand appearance: Walter Tools), with headquarters in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Mark names and protected trade names are mentioned solely for explanation. There is no affiliation between our company and the named brands. The offered item is an original, new product of the respective manufacturer.
WCGT030202-X5 WAK15 Wendeplatten - Walter Tools
Take advantage of the combination of the WAK15 uncoated carbide grade, the Trigon 80° geometry and the X5 chipbreaker to achieve reliable, high‑quality machining of aluminium and other non‑ferrous metals; order the insert directly via Metav Werkzeuge or contact our consultants for application advice. WCGT030202-X5 WAK15 — Indexable drilling/boring insert, Trigon 80°, for aluminium — Walter Tools A WCGT030202-X5 WAK15 indexable insert designed for efficient drilling and boring of aluminium and other non‑ferrous metals with a Trigon 80° geometry. Uncoated carbide WAK15 for non‑ferrous metals Trigon 80° form for stable cutting geometry 7° clearance angle reduces flank contact X5 chipbreaker for controlled chips Consistent chip control and edge quality for aluminium machining The uncoated WAK15 carbide grade, developed within the Walter N‑grade system, is optimised for aluminium and other non‑ferrous materials that demand very sharp cutting edges and low friction. The X5 chipbreaker promotes predictable fragmentation and evacuation of continuous chips common with soft alloys, reducing the risk of material adhesion and built‑up edge. For production environments, this translates into fewer interruptions for cleaning, a more consistent surface integrity and improved cycle‑time stability. The chemical concept and geometry are chosen to favour abrasion resistance while maintaining a keen edge suitable for light to medium depths of cut. Geometry that stabilises drilling and improves surface results The Trigon 80° insert form combines a compact seating area with pronounced cutting edge support to deliver stable engagement in drilling and boring applications. With a 7° clearance angle and a 0.2 mm corner radius, the insert reduces rubbing on the flank, which helps to lower vibration and heat generation during the cut. The relatively small corner radius supports a sharper entry into the material, improving centring and enabling a finer surface finish on bores. These geometric choices provide a balance between edge strength and cutting sharpness, making the insert suitable where controlled penetration and surface quality are priorities. Operational guidance for productive use and tool selection This indexable insert is supplied in the WCGT030202‑X5 configuration with a thickness and size coded by the manufacturer for modular toolholders. The combination of uncoated carbide and the X5 chipbreaker makes it particularly suitable for high feed operations in aluminium and similar alloys; coolant strategy and spindle speed should be selected to avoid excessive built‑up edge—typical practice is to favour moderate speeds with adequate chip evacuation. For specific machine settings, recommended feeds and holder compatibility, Metav Werkzeuge provides application guidance and can suggest suitable toolholders or adaptations for existing drills and boring heads to ensure the best performance and repeatability. Contact Metav Werkzeuge to discuss suitability of the WCGT030202‑X5 WAK15 insert for a specific application or to request tailored recommendations; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: WCGT030202-X5-WAK15-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WCGT030202-X5 WAK15 Walter Tools Product type: Bohr-/Aufbohrwendeschneidplatte (indexable insert for drilling/boring) Manufacturer: Walter Tools Series: Walter N‑Sortensystem Grade: WAK15 ISO designation: WCGT030202-X5 WAK15 Form: Trigon 80° Chipbreaker: X5 Execution: T Tolerance class: G Material code: N Aluminium application: yes Facts Clearance angle: 7° Corner radius: 0.2 mm Plate form angle: 80° Plate size code: 03 Thickness code: 02 Special features Uncoated carbide grade WAK15 Designed for aluminium and non‑ferrous metals Part of the Walter N‑grade system X5 chipbreaker for improved chip control Trigon 80° geometry for stable cutting Execution code T for seat/fit compatibility FAQ What materials is this insert intended for? The WCGT030202‑X5 WAK15 insert is intended primarily for aluminium and other non‑ferrous metals, following the Walter N‑grade designation. How does the X5 chipbreaker affect machining? The X5 chipbreaker on the insert promotes predictable chip formation and evacuation, reducing material adhesion and improving process stability when machining soft alloys. What is the advantage of the Trigon 80° form? The Trigon 80° geometry offers robust edge support and a compact seating area that enhances stability in drilling and boring applications, which helps achieve better surface results. Is the WAK15 grade coated or uncoated, and why does that matter? The WAK15 grade is uncoated carbide; this supports a sharper cutting edge and reduces the tendency for aluminium to adhere to the tool, improving edge life in non‑ferrous machining. Can this insert be used in existing toolholders? The WCGT030202‑X5 insert is supplied in a common indexable format; compatibility depends on the toolholder seat and the execution code (T). For holder matching, Metav Werkzeuge can advise on suitable toolsets. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and protected product designations are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is an original, factory‑new product of the manufacturer.
WCGT030202-X5 WTP35 T Wendeplatten - Walter Tools
Combine the cost-effectiveness of a coated carbide grade with reliable chip control and precise geometry to maintain consistent drilling and reaming results in production environments; order directly via Metav Werkzeuge or consult the Metav specialists for application guidance. WCGT030202-X5 WTP35 – Trigon 80° indexable insert with X5 chipbreaker (Walter Tools) The WCGT030202-X5 WTP35 is a trigon 80° insert for drilling and reaming operations, engineered to provide stable cutting behaviour and predictable chip formation in general machining tasks. Coated carbide grade WTP35 Trigon 80° geometry X5 chipbreaker for chip control 7° relief angle for penetrating cuts Reliable cutting across a broad range of components The coated carbide composition of the grade WTP35 provides a balance between wear resistance and toughness, making the tool suited to varying production demands. As a trigon 80° insert, the geometry concentrates cutting forces effectively, improving stability in bore-making processes. This results in fewer vibrations and a lower risk of edge chipping, which translates into more consistent hole quality and reduced rework rates in batch production. Predictable chips and a consistent surface finish Thanks to the X5 chipbreaker, chip formation is controlled even under interrupted cuts; chips are directed away from the cutting zone to reduce recutting. The modest corner radius (0.2 mm) helps to maintain a clean transition at the cut edge and supports a steady surface finish without aggressive material removal. Such chip control shortens cycle times by reducing stoppages for chip clearing and contributes directly to process reliability on the shop floor. Longer tool life and efficient machining economy The balanced coating and edge geometry aim to extend the usable life of the insert while preserving dimensional accuracy across multiple parts. Fewer insert changes and reduced scrap yield measurable cost benefits over time. Where process stability is a priority, the 7° relief angle helps with initial penetration and lowers cutting forces, which not only preserves the cutting edge but also reduces spindle load in high-volume operations. Straightforward integration and practical handling The insert is delivered in a standard indexable form factor compatible with common drilling and reaming toolholders. Assembly and index changes are quick and predictable, enabling fast tool replacement and minimal production interruption. For unfamiliar material conditions, the recommendation is to consult the product matrix for exact material suitability and to match cutting parameters to the chosen grade to ensure optimal performance. Contact Metav Werkzeuge for tailored application advice on Walter Tools inserts and the WTP35 grade — our consultants will recommend the right setup for the machining task at hand. Technical data Article number: WCGT030202-X5-WTP35-WALTER Item designation: WCGT030202-X5 WTP35 Product type: Bohr-/Aufbohrwendeschneidplatte Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.2 mm Insert size designation: 03 Thickness designation: 02 Tolerance class: G Special features Coating / grade: coated carbide (WTP35) Geometry: Trigon 80° Chipbreaker: X5 Series: Walter Schneidstoffsorte - Serie offen Execution: T Material: catalogue-dependent FAQ Is this insert suitable for a wide range of materials? The WCGT030202-X5 WTP35 is a coated carbide insert designed for general machining; material suitability should be confirmed against the product matrix for best results. What advantage does the X5 chipbreaker provide? The X5 chipbreaker offers controlled chip formation and evacuation, reducing the risk of recutting and improving cycle stability with this Walter Tools insert. How does the Trigon 80° geometry affect performance? Trigon 80° geometry concentrates cutting forces for stable penetration and reduced vibration, which helps maintain hole geometry and tool life. Can the insert be used for interrupted cuts? Yes, the combination of the coated grade and the X5 chipbreaker supports interrupted cutting conditions, though cutting data should be adapted to the application. What does the ‘02’ thickness designation mean for tool setup? The thickness designation is part of the insert sizing system; ensure the corresponding toolholder matches the 02 designation for secure clamping and correct axial positioning. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany. Protected trademarks and trade names remain the property of their respective owners. Mark names and protected designations are used for explanation only. There is no affiliation between our company and the named manufacturers. The offered article is original, factory-new goods of the manufacturer.
WCGT030202-X5 WXM15 Wendeplatten - Walter Tools
Take advantage of an uncoated, application‑specific grade and an optimised chipbreaker to ensure clean, reliable removal of non‑ferrous material; combine WXM15 carbide with the X5 geometry for reduced built‑up edge and consistent bore quality. Order through Metav Werkzeuge or contact the consultants for application advice and delivery options. WCGT030202-X5 WXM15 — Drilling/boring indexable insert, Trigon 80°, X5 chipbreaker — Walter Tools A WCGT030202-X5 WXM15 indexable insert designed for efficient machining of non‑ferrous metals in drilling and bore‑enlargement operations. WXM15 uncoated carbide for non‑ferrous metals Trigon 80° geometry for axial stability X5 chipbreaker for reliable chip control 7° relief and 0.2 mm corner radius High‑precision cutting for non‑ferrous components The insert combines an uncoated carbide grade with a geometry optimised for soft, adhesive materials. The WXM15 grade is engineered as an uncoated hardmetal suited to aluminium, copper and brass (ISO group N), where extremely sharp edges and low friction are essential. The chipbreaker X5 reduces the risk of long, stringy chips and minimises material adhesion on the cutting edge, which maintains surface finish and extends usable edge life. For shops producing high volumes of non‑ferrous parts, this results in fewer interruptions and more predictable machining cycles. Geometry that balances strength and surface quality The Trigon 80° form and a 0.2 mm corner radius provide a compromise between a sharp cutting edge and the mechanical strength required at entry to the bore. A 7° relief angle reduces rubbing while preserving edge support, so axial forces remain controlled during plunge and reaming passes. This geometry lowers the tendency for built‑up edge and helps achieve repeatable bore diameters and improved surface texture, essential when tolerances are tight or subsequent assembly demands consistent fit. Practical integration into tool systems and processes As an indexable insert for drilling and boring tools, the WCGT030202‑X5 WXM15 fits into standard Walter tool holders and is part of the Walter N‑grade system, facilitating grade selection across a machine park. The insert’s profile and chip control are especially beneficial for interrupted cuts or variable feed rates common in production drilling. Because the grade is uncoated, coolant and cutting parameters should be adjusted to avoid thermal softening in heavy cuts; in light to moderate feeds typical for non‑ferrous metals, the result is crisp chips and excellent repeatability. Operational benefits and handling guidance With a defined tolerance class (G) and compact plate dimensions, the insert enables consistent seating and straightforward indexation. The combination of X5 chip control and trigon geometry supports shorter cycle times through stable chip evacuation and fewer manual clean‑ups. For best results, monitor edge condition visually and by part inspection; replace or index the insert when edge rounding begins to affect surface finish rather than waiting for catastrophic wear. This approach preserves machine uptime and upholds production quality. Contact Metav Werkzeuge today for tailored advice on integrating Walter Tools inserts like the WCGT030202-X5 WXM15 into your process and to arrange delivery or further technical details Technical Data Article number: WCGT030202-X5-WXM15-WALTER Item label: Bohr-/Aufbohrwendeschneidplatte WCGT030202-X5 WXM15 Walter Tools Manufacturer: Walter Tools Series: Walter N‑Sortensystem Grade: WXM15 ISO designation: WCGT030202-X5 WXM15 Facts Relief angle: 7° Corner radius: 0.2 mm Plate form: Trigon 80° Plate size: 03 Plate thickness: 02 Tolerance class: G Special features Chipbreaker: X5 Execution: T Material code: N Optimised for ISO group N (non‑ferrous metals) Uncoated hardmetal (WXM15) — sharp edge, low adhesion FAQ What materials is this insert intended for? The insert is designed for ISO group N materials; the WXM15 uncoated hardmetal is optimised for aluminium, copper and brass, where reduced adhesion and sharp cutting edges are required. How does the X5 chipbreaker affect machining? The X5 chipbreaker produces short, controlled chips and reduces long, stringy chip formation; this supports stable evacuation during drilling and improves surface quality while lowering the risk of material cling on the cutting edge. What are the benefits of the Trigon 80° geometry for bore operations? The Trigon 80° shape offers axial stability and predictable entry behaviour, helping to maintain bore roundness and concentricity during plunge cuts and bore enlargements. Is the grade coated or uncoated, and what does that mean for coolant use? This is an uncoated WXM15 grade; for non‑ferrous applications, this helps avoid coating‑related adhesion, but coolant strategy should be chosen to control temperatures during heavier cuts. How should insert wear be monitored in production? Inspect for edge rounding and increasing burr or surface roughness on finished parts; indexing or replacing the insert when finish degrades prevents scrap and keeps cycle times stable. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Trademarks and trade names are the property of their respective owners. Brand names and protected product names are used here for explanatory purposes only; there is no affiliation between our company and the named brands. The offered article is an original, factory‑new product of Walter Tools.
WCGT030204-FM2 WSM21 T Wendeplatten - Walter Tools
Take advantage of a high-performance, coated cemented carbide grade designed for demanding materials and a compact Trigon 80° geometry that delivers stable chip formation and repeatable results; order directly via Metav Werkzeuge or consult their experts for application support. WCGT030204-FM2 WSM21 indexable insert — Trigon 80° geometry, FM2 chipbreaker (Walter Tools) The WCGT030204-FM2 WSM21 is an indexable insert for drilling, boring and turning applications, engineered for machining rostfreier Stahl and heat-resistant superalloys in production and repair environments Coated cemented carbide WSM21 grade Trigon 80° insert geometry FM2 chipbreaker for stable chip control Suited for rostfreier Stahl and superalloys Optimised grade for difficult-to-machine materials and consistent productivity The WSM21 grade is a coated cemented carbide developed for materials that challenge conventional tooling. Its substrate and coating combination enhance heat resistance and edge life when facing the higher work hardening and thermal loads typical of rostfreier Stahl and superalloys. For production lines that require fewer tool changes and predictable tool life, this insert supports consistent cutting performance and reduced downtime. The specification of a coated carbide grade means improved wear resistance and a higher tolerance to thermal shock compared with uncoated substrates. Geometry and edge preparation that control cutting forces and surface results The Trigon 80° form and 0.4 mm corner radius balance strength and form detail for general finishing and light semi-finishing passes. A 7° relief angle reduces rubbing while maintaining edge support under radial and axial loads, which helps to lower cutting temperatures and micro-chipping. The compact plate dimensions (size 03, thickness 02) make the insert suitable for tight-pocket toolholders and versatile turning fixtures, while the trigon shape offers three usable cutting edges for economical indexing. These geometric choices translate into stable cutting forces and improved surface integrity on difficult alloys. Chip control, process security and shop-floor advantages The FM2 chipbreaker is tuned for forming and evacuating chips when machining sticky, work-hardening materials. Stable chip formation reduces the risk of build-up on the cutting edge and limits secondary thermal loading, thereby extending effective tool life. With tolerance class G and repeatable seating geometry, the insert contributes to predictable assembly and interchangeability across toolholders. For production engineers this means fewer interruptions, more reproducible cycle times and a clearer path to process optimisation when working with rostfreier Stahl and titanium-alloy components. For supply, application recommendations and availability of the Walter Tools WCGT030204-FM2 WSM21 insert, contact Metav Werkzeuge for tailored advice and order handling: Metav Werkzeuge GmbH – info@metav-werkzeuge.com – +49 2822 7131930 Technical data SKU: WCGT030204-FM2-WSM21-WALTER Designation: WCGT030204-FM2 WSM21 Manufacturer: Walter Tools Core data Geometry: Trigon 80° Relief angle: 7° Corner radius: 0.4 mm Plate size: 03 Plate thickness: 02 Tolerance class: G Special features Chipbreaker: FM2 Grade: WSM21 (coated cemented carbide) Material groups: M (rostfreier Stahl), S (superalloys/titanium) Suitable for demanding, heat-resistant materials FAQ What materials is this insert intended for? The WCGT030204-FM2 WSM21 insert is designed primarily for rostfreier Stahl and heat-resistant superalloys, supporting secure chip formation and stable cutting edges. Is the FM2 chipbreaker suitable for finishing operations? Yes, the FM2 chipbreaker provides controlled chip formation and can be used for finishing and light semi-finishing on difficult alloys. How does the Trigon 80° shape affect tool life? The Trigon 80° geometry offers a robust cutting edge and three indexable sides, which increases usable edge count and contributes to economical tool life management. What does the tolerance class G indicate for workshop use? Tolerance class G denotes precise seating and interchangeability, helping to achieve reproducible setup and consistent cutting behaviour in serial production. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned for identification purposes only. The offered item is an original, factory-new product of the manufacturer.
WCGT030204-FN2 WNN10 Wendeplatten - Walter Tools
The combination of coated carbide grade and the FN2 chipbreaker delivers reliable chip control and consistent tool life, supporting efficient turning and boring processes. Choose the Walter Tools solution for stable edge performance and contact Metav Werkzeuge for tailored advice or procurement assistance. WCGT030204-FN2 WNN10 — Trigon 80° turning/boring insert by Walter Tools, FN2 chipbreaker A compact WCGT030204-FN2 WNN10 indexable insert designed for turning and boring tasks, offering controlled chip formation and a balanced geometry for finishing and semi-finishing applications. Trigon 80° geometry for stable seating FN2 chipbreaker for improved chip control Coated carbide WNN10 grade for durability 0.4 mm corner radius for precise edge Improved productivity through controlled chip flow and reliable wear behaviour The insert combines a Trigon 80° profile with a tailored FN2 chipbreaker, resulting in stable chip formation and reduced interruption of machining cycles. The coated carbide composition of the WNN10 grade supports wear resistance under typical turning loads; material suitability should be verified in the product matrix before application. This geometry and chip control reduce secondary operations associated with poor chip evacuation, helping to maintain throughput and minimise downtime in production settings. Dependable edge geometry that supports repeatable surface quality A modest 0.4 mm corner radius together with a 7° clearance ensures consistent contact conditions at the cutting edge, which contributes to precision and repeatable results part after part. The insert’s form factor and thickness code offer mechanical stability in the cutter pocket, reducing vibration and promoting a stable cutting edge. For operations where surface finish and dimensional consistency matter, these design choices help reduce rework and maintain process reliability. Practical selection and integration into existing tooling systems The open-series Walter grade is supplied with catalogue-dependent material options; verify the exact coating and substrate for the chosen variant. The WNN10 designation denotes a coated carbide class intended for general-purpose performance; consult the technical matrix for recommended workpiece materials and cutting parameters. Integration is straightforward for holders that accept the WCGT series; check seat conformity and tightening specifications to achieve correct clamp force and repeatable alignment. For customised recommendations, technical consultancy is available. Contact Metav Werkzeuge to discuss Walter Tools options and to identify the optimal WCGT030204-FN2 WNN10 variant for specific production requirements Technical data Article number: WCGT030204-FN2-WNN10-WALTER Designation: WCGT030204-FN2 WNN10 Type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Manufacturer: Walter Tools Facts Plate form: Trigon 80° Clearance angle: 7° Corner radius: 0.4 mm Chipbreaker: FN2 Plate size: 03 Plate thickness code: 02 Tolerance class: G Special features Series: Walter Schneidstoffsorte - Serie offen Grade: WNN10 (coated carbide) Execution: T Designation without grade: WCGT030204-FN2 Note: Material specifics catalogue-dependent Recommendation: Check product matrix for material suitability FAQ What is the primary application for this insert? The insert is optimised for turning and boring operations where controlled chip formation and consistent edge performance are required; the WCGT030204-FN2 WNN10 is suitable for finishing and semi-finishing tasks depending on the selected grade variant. How does the FN2 chipbreaker affect machining? The FN2 chipbreaker on the WCGT030204-FN2 WNN10 promotes short, manageable chips and supports stable cutting conditions, which reduces the likelihood of chip-related interruptions in continuous production. Is the WNN10 grade suitable for stainless or hardened materials? The WNN10 grade is a coated carbide class; specific suitability for stainless or hardened steels must be confirmed in the product matrix for the chosen variant of the insert. What should be checked before fitting the insert into a cutter body? Verify seat geometry, clamp method and pocket compatibility with the WCGT series to ensure correct alignment and clamping force for repeatable performance. Can this insert help improve surface finish? Yes—due to the 0.4 mm corner radius and the consistent geometry, the insert supports improved surface quality when used within recommended cutting parameters. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik-Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WCGT030204-MN2 WNN10 Wendeplatten - Walter Tools
Benefit from the combination of a coated carbide WNN10 grade and a precise MN2 chipbreaker for steady chip control and consistent tool life; this insert supports productive machining with reliable repeatability. Order the insert through Metav Werkzeuge or consult the technical team for application guidance. WCGT030204-MN2 WNN10 — Indexable insert (Trigon 80°) by Walter Tools WCGT030204-MN2 WNN10 is an indexable insert designed for drilling/reaming and turning applications, offering a Trigon 80° geometry and a chipforming solution for mixed production environments Coated carbide grade WNN10 Trigon 80° insert form MN2 chipbreaker for controlled chips 7° clearance angle for stable cutting Precision and productivity from a coated carbide grade The combination of a coated carbide substrate and the WNN10 grade provides a balance between wear resistance and reliable edge stability, making the insert suitable for demanding, repeatable operations. The MN2 chipbreaker is engineered to promote predictable chip formation, which reduces interruptions and helps maintain cycle times. For purchasers and process planners, the result is improved machine uptime and fewer unplanned tool changes, contributing directly to process efficiency and cost effectiveness. Geometry and edge design that reduce rework The Trigon 80° form and a 0.4 mm corner radius deliver a robust cutting edge that resists chipping under transverse loads. The modest 7° clearance angle reduces rubbing while maintaining positive engagement, which supports consistent surface finish in both boring and turning modes. For less technical readers: the corner radius and clearance angle are small, measurable design choices that together help avoid premature edge failure and reduce the need for secondary finishing. Simple integration into existing tooling systems With the ISO designation WCGT030204-MN2 WNN10, this insert fits established toolholders that accept Trigon 80° plates, enabling straightforward replacement in current tool assemblies. The insert’s tolerance class G and standard plate size ensure interchangeability across suitable holders; this simplifies inventory management and reduces tooling complexity. Where material suitability is critical, the product matrix should be consulted to confirm the grade’s match to the target workpiece. Application guidance and process assurance The coated-grade construction and the chipformer design focus on stable removal rates and consistent cutting behaviour in mixed-production contexts. For customers requiring support with parameter selection or compatibility checks, technical consultation is available to align cutting speeds and feeds with the material and machining strategy. This measured approach reduces risk and supports reproducible component quality during serial production. For technical verification of the Walter Tools WCGT030204-MN2 WNN10 insert and to discuss suitability for specific machining tasks, contact Metav Werkzeuge for application advice and stock information at info@metav-werkzeuge.com or +49 2822 7131930. Technical data SKU: WCGT030204-MN2-WNN10-WALTER Article: WCGT030204-MN2 WNN10 Product type: Drill/reaming and turning indexable insert Grade: WNN10 Series: Walter Schneidstoffsorte - Serie offen Execution: T Material: catalogue-dependent Numbers / Core technical data Clearance angle: 7° Corner radius: 0.4 mm Insert form: Trigon 80° Plate size: 03 Plate thickness: 02 Tolerance class: G Special features / Design Chipbreaker: MN2 Coating / grade: coated carbide (WNN10) ISO designation: WCGT030204-MN2 WNN10 Application note: check product matrix for material suitability FAQ What materials is this insert suitable for? Material suitability must be checked in the product matrix; the WNN10 grade is a coated carbide class intended for a broad range of applications as specified by Walter Tools Can the insert be used for both drilling and turning operations? Yes — the design as a drill/reaming and turning indexable insert allows use in compatible holders for both modes, subject to correct toolholder selection and machining parameters What does the MN2 chipbreaker deliver in practice? The MN2 chipbreaker promotes controlled chip formation, which helps maintain stable machining cycles and reduces the likelihood of chip-related interruptions How does the Trigon 80° geometry affect cutting performance? The Trigon 80° geometry provides a strong cutting edge capable of withstanding lateral loads and contributes to consistent surface finish in finishing and semi-finishing passes Is the WCGT030204-MN2 WNN10 insert interchangeable with other ISO-designated inserts? Interchangeability depends on holder compatibility and tolerance class; the ISO designation and tolerance class G support integration into standard tool systems designed for Trigon 80° inserts Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is original factory-new goods of the manufacturer (Walter Tools).
WCGT030204-X15 WAK15 Wendeplatten - Walter Tools
Take advantage of the combination of a trigonal 80° geometry, a sharp cutting-grade carbide suited to aluminium and non‑ferrous metals, and a chipbreaker designed for consistent chip control to maintain steady production. Order direct via Metav Werkzeuge or consult the technical team for application-specific recommendations. WCGT030204-X15 WAK15 — Drilling/boring indexable insert for aluminium and non‑ferrous metals (Walter Tools) WCGT030204-X15 WAK15 is a trigonal indexable insert developed for precise drilling and boring of aluminium and other non‑ferrous alloys, offering a cutting geometry and grade optimised for low adhesion and stable chip formation. Uncoated carbide grade WAK15 for non‑ferrous metals Trigon 80° geometry for stable chip control 7° relief angle for sharp, low‑resistance cutting 0.4 mm corner radius for repeatable hole quality Consistent performance in aluminium machining The WCGT030204-X15 WAK15 is tailored to the challenges of machining aluminium and similar non‑ferrous materials. The uncoated WAK15 carbide grade provides a very sharp cutting edge that reduces the risk of material buildup on the tool face, improving surface finish and dimensional stability. For operations where adhesion and clogged flutes are common problems, this insert’s geometry and grade work together to maintain efficient metal removal and minimise interruptions to production. Geometry designed for stable chips and repeatable holes The Trigon 80° shape and chipbreaker X15 combine to direct chips reliably away from the cutting zone, supporting uninterrupted drilling and boring cycles. A 7° relief angle reduces cutting resistance while preserving edge strength, and the 0.4 mm corner radius balances edge robustness with hole accuracy. These features translate into fewer reworks, more consistent hole tolerances and improved repeatability across batch production, which is particularly valuable in serial manufacturing environments. Productivity advantages and process reliability Integrating this insert into a Walter tooling system contributes to measurable efficiency gains: fewer tool changes, reduced secondary finishing and steadier cycle times. The Walter N‑series design philosophy underpins predictable behaviour in aluminium machining, promoting productive chip formation and reliable performance. For shops focused on throughput, the insert’s specification supports longer uninterrupted runs and helps to lower unit processing time, creating a clear cost‑benefit in medium to high‑volume work. Simple selection and workshop handling The insert’s size code 03 and thickness code 02, together with its trigonal form, make it compatible with common drilling and boring holders designed for indexable inserts. The clear specification—grade for non‑ferrous materials, chipbreaker X15, trigonal geometry and modest corner radius—simplifies tooling decisions when replacing or upgrading inserts for aluminium tasks. If material mixture or machining strategy is uncertain, Metav Werkzeuge’s advisors can assist with holder matching and process setup to ensure the insert is applied where it performs best. Contact Metav Werkzeuge for tailored advice on Walter Tools inserts like the WCGT030204-X15 WAK15 and for quick delivery or technical clarification; eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data Article number: WCGT030204-X15-WAK15-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WCGT030204-X15 WAK15 Walter Tools Manufacturer: Walter Tools Product type: Drilling/boring indexable insert Series: Walter N‑Sortensystem Core dimensions Relief angle: 7° Corner radius: 0.4 Plate form: Trigon 80° Plate size: 03 Plate thickness: 02 Special features Grade: WAK15 (uncoated carbide) Chipbreaker: X15 Execution: T Tolerance class: G Application: Aluminium and non‑ferrous metals FAQ What materials is this insert intended for? The insert is specified for aluminium and other non‑ferrous metals; the WAK15 grade and chipbreaker X15 are chosen to reduce adhesion and promote clean chip formation when machining these materials. Is the WAK15 grade coated? No, the WAK15 grade used in this insert is an uncoated carbide formulation, which is advantageous for many aluminium applications where coatings can increase built‑up edge. How does the Trigon 80° shape affect drilling? The Trigon 80° geometry provides stable contact and controlled chip flow during drilling and boring, helping to maintain hole quality and reduce vibration compared with less robust geometries. Can this insert be used in standard indexable drill holders? Yes, the insert’s trigonal form and size code make it compatible with holders designed for indexable inserts of this family, but correct seat and clamp type should be confirmed before use. Walter Tools is a registered brand and is mentioned for identification of the original product. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are cited solely for explanatory purposes; there is no affiliation between our company and the mentioned brands. The offered article is original, factory‑new merchandise from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
WCGT030204-X15 WTP35 WTP35 Wendeplatten - Walter Tools
Take advantage of the combination of robust geometry and a coated carbide grade for dependable chip control and extended tool life; order directly via Metav Werkzeuge or ask our consultants for application advice. WCGT030204-X15 WTP35 drilling/reaming indexable insert, Trigon 80° geometry, 7° clearance — Walter Tools The WCGT030204-X15 WTP35 is a trigon-shaped drilling and reaming indexable insert designed for productive metal removal with stable chip control and repeatable performance. Trigon 80° geometry for stable cutting 7° clearance angle for reliable engagement Coated carbide grade WTP35 for long life X15 chipbreaker for controlled chips Stable cutting and predictable engagement for higher throughput The trigon 80° geometry combined with a 7° clearance provides a stable cutting contact that reduces vibration and supports consistent hole quality. This geometry distributes cutting forces across the insert, which lowers the risk of premature edge damage and contributes to steady process behaviour. In practical terms, operators benefit from fewer interruptions and improved cycle-time predictability when working with the trigon insert in medium to heavy machining tasks. Longer service intervals thanks to WTP35 coated carbide The WTP35 classification denotes a coated carbide grade optimised for broad use; the coating improves wear resistance and helps maintain a sharp cutting edge under industrial loads. This translates into extended tool life and reduced frequency of index changes compared with uncoated options. For production environments where tool changeover time affects throughput, the WTP35 grade supports economical, continuous machining while delivering consistent results. Controlled chip formation increases process security The X15 chipbreaker is designed to produce short, manageable chips in a wide range of cutting conditions, enhancing chip control and reducing the risk of entanglement or rework. Better chip behaviour improves coolant access and contributes to safer, cleaner operation at the machine. Stable chips also reduce operator intervention and protect both the insert and workpiece surface, supporting reproducible quality in serial production. Flexible application scope with clear selection guidance The insert’s dimensions — trigon shape, 03 size and 02 thickness with an edge radius of 0.4 mm — suit many common drilling and reaming toolholders. Material suitability should be confirmed via the manufacturer’s product matrix to ensure optimal performance for specific alloys or heat-treated steels. Where machining requirements are mixed, the combination of geometry, chipbreaker and WTP35 coating provides a balanced solution for productivity and surface finish. Consult Metav Werkzeuge for tailored grade and holder recommendations, or request application guidance by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 — Metav Werkzeuge supports specification decisions for Walter Tools inserts Technical data Article number: WCGT030204-X15-WTP35-WALTER Designation: WCGT030204-X15 Type: drilling/reaming indexable insert Specifications Clearance angle: 7° Corner radius: 0.4 mm Plate form: Trigon 80° Plate size: 03 Plate thickness: 02 Tolerance class: G Special features Coating / grade: WTP35 (coated carbide) Chipbreaker: X15 Series: Walter Schneidstoffsorte - Serie offen Material: catalogue-dependent ISO designation: WCGT030204-X15 WTP35 FAQ What materials is this insert suitable for? Workpiece suitability should be verified using the product matrix; the WCGT030204-X15 WTP35 insert is a coated carbide grade intended for a broad material spectrum, with exact suitability indicated in Walter Tools’ product documentation. How does the Trigon 80° geometry affect hole quality? The Trigon 80° geometry of the insert promotes stable cutting forces and reduced vibration, which supports consistent hole roundness and surface finish when the insert is mounted in a compatible drilling or reaming holder. What advantages does the X15 chipbreaker bring? The X15 chipbreaker is engineered for short, controlled chips, improving chip evacuation and coolant contact; this reduces downtime for chip clearing and helps maintain surface integrity during drilling and reaming operations. How should the edge radius be selected for finishing tasks? The 0.4 mm edge radius balances edge strength with the potential for finer surface finishes; for demanding finishing passes, consideration of feed, speed and holder rigidity together with the insert’s edge radius will determine the optimal set-up. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Trademarks and trade names are the property of their respective owners. Mentions of brand names are for explanation only and do not imply any affiliation with our company. The presented article is original and factory-new from the manufacturer. The Walter Tools brand is referenced where relevant.
WCGT030204-X15 WXM15 WXM15 Wendeplatten - Walter Tools
Benefit from the combination of a sharp Trigon 80° geometry and the robust uncoated carbide grade for reliable performance in non‑ferrous machining; order directly via Metav Werkzeuge or consult our specialists for application advice. WCGT030204-X15 WXM15 — Drilling/bore‑reaming indexable insert, Trigon 80°, 7° relief (Walter Tools) A WCGT030204-X15 WXM15 insert engineered for precision drilling and bore‑reaming applications, optimised for non‑ferrous metals and designed to ensure consistent chip formation. Trigon 80° insert form 7° relief angle for precise engagement Uncoated carbide grade WXM15 Optimised for non‑ferrous metals Precise geometry for stable drilling and reaming results The Trigon 80° form and a 7° relief angle provide a stable seat and consistent cutting engagement, which supports accurate hole-making operations. The modest corner radius 0.4 mm balances edge strength with a sharp cutting profile to reduce burr formation in softer alloys. These geometric choices are particularly beneficial when machining aluminium, copper and brass, where controlled chip flow prevents material build-up and secures repeatable hole quality. Material grade and chip control that reduce interruptions Built from an uncoated carbide grade WXM15, the insert is adapted to non‑ferrous workpieces where low adhesion and clean chip evacuation are decisive. The X15 chipbreaker promotes predictable chip formation, assisting tool life and reducing the frequency of operator intervention. For workshops aiming for productive series runs, this combination helps maintain process reliability without resorting to coatings that are unnecessary for these materials. Application-focused advantages for workshop efficiency The insert’s dimensions — plate size 03 and thickness 02 — together with the trigon shape, allow compact toolholder designs that suit both drilling and bore‑reaming stages. The compact format supports versatile tool setups and facilitates quick indexable changes, contributing to shorter downtime between operations. For manufacturing environments handling non‑ferrous batches, the insert’s geometry and chip control translate into smoother workflows and predictable finishing. Compatibility, handling and selection guidance The insert is part of the Walter N‑grade system, a range developed for non‑ferrous machining. Selection of the grade WXM15 reflects a focus on sharpness and low friction rather than coated wear resistance, which is appropriate for aluminium and related alloys. When integrating into existing tool systems, ensure the toolholder matches the Trigon 80° seat and that the X15 chip control aligns with the expected feed and speed settings to achieve optimal results. Contact Metav Werkzeuge for expert advice on using Walter Tools inserts like the WCGT030204-X15 WXM15 in non‑ferrous production and to discuss compatible toolholders and cutting parameters Technical data SKU: WCGT030204-X15-WXM15-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WCGT030204-X15 WXM15 Walter Tools Product type: Drilling/bore‑reaming indexable insert Facts Relief angle: 7° Corner radius: 0.4 mm Insert form: Trigon 80° Plate size: 03 Thickness: 02 Special features Grade: WXM15 (uncoated carbide) Chipbreaker: X15 Series: Walter N‑Sortensystem Material group: N (non‑ferrous metals) FAQ What materials is this insert intended for? The WCGT030204-X15 WXM15 insert is specified for N‑group materials, meaning non‑ferrous metals such as aluminium, copper and brass, and is optimised to avoid material adhesion. Is the grade coated or uncoated? The WXM15 grade is an uncoated carbide developed for sharp cutting edges and low adhesion when machining non‑ferrous workpieces. Which insert geometry ensures correct seating in toolholders? The Trigon 80° form with a 7° relief angle ensures secure seating and precise engagement in compatible drilling and bore‑reaming toolholders. Does the chipbreaker influence surface finish? The X15 chipbreaker promotes controlled chip formation, which supports consistent surface quality and reduces the risk of built‑up edge during non‑ferrous machining. Can this insert be used for both drilling and reaming operations? Yes, the insert is designed as a drilling/bore‑reaming indexable insert and suits combined operations when mounted in appropriate holders and used with matching feeds and speeds. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original, new manufacturer goods.
WCGT030204-X25 WK1 T Wendeplatten - Walter Tools
Take advantage of the combination of a Trigon 80° geometry, reliable chip control (X25) and the economical WK1 uncoated carbide grade for stable drilling and boring operations. Order directly via Metav Werkzeuge or consult our technical advisors for material suitability and process optimisation. WCGT030204-X25 WK1 — Drill/boring indexable insert, Trigon 80°, uncoated carbide (Walter Tools) The WCGT030204-X25 WK1 is a Trigon 80° indexable insert for drilling and boring applications, designed to offer controlled chip formation and reproducible cutting performance; check the manufacturer’s product matrix for specific material compatibility. Trigon 80° insert geometry Uncoated carbide grade WK1 0.4 mm corner radius 7° clearance angle Controlled chip flow for consistent productivity The Trigon 80° geometry combined with the chipbreaker X25 is engineered to deliver predictable chip formation during drilling and boring cycles, which reduces interruptions and improves cycle times. The geometry supports reliable evacuation in a range of rigid setups and contributes to repeatable hole quality. For production environments seeking efficiency, the reduced risk of chip jamming translates into fewer stoppages and more consistent throughput. Robust edge design for repeatable hole accuracy A 0.4 mm corner radius and a 7° clearance angle provide a balance between edge strength and cutting stability. The modest corner radius helps absorb contact stresses at entry and exit while supporting a defined cutting edge for accurate hole profiles. The Trigon form also helps maintain lateral stability in the toolholder, which benefits concentricity and dimensional control in short to medium depth operations. Grade and coating: what WK1 means in practice The insert is supplied in the WK1 uncoated carbide grade, an uncoated hardmetal intended for general-purpose performance; as an uncoated carbide, it is often chosen where toughness and predictable wear behaviour are priorities. Material suitability varies by application—refer to the manufacturer’s product matrix for recommended workpiece types and cutting-parameter ranges. Choosing the correct grade and cutting data ensures tool life and surface integrity are optimised. Practical benefits for the workshop and production line Using a standardised Trigon insert such as this reduces inventory complexity while offering straightforward indexability and economical re-use of toolholders. The insert’s design supports fast index changes and reliable seating in standard toolholders, lowering downtime during tool changeovers. For system integrators and workshop managers, the combination of geometry and grade provides a pragmatic route to stabilised processes and predictable maintenance intervals. Contact Metav Werkzeuge to discuss how the Walter Tools WCGT030204-X25 WK1 insert fits into specific applications or to request a tailored recommendation for your machining tasks. Metav Werkzeuge’s consultants are available to review the product matrix and cutting parameters. Technical data Article number / SKU: WCGT030204-X25-WK1-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WCGT030204-X25 WK1 Walter Tools Manufacturer: Walter Tools Product type: Drill/boring indexable insert Designation: WCGT030204-X25 WK1 Numbers / core technical data Corner radius: 0.4 mm Clearance angle: 7° Plate size: 03 Thickness: 02 Tolerance class: G Designs / special features Insert shape: Trigon 80° Chipbreaker: X25 Grade: WK1 (uncoated carbide) Series: Walter Schneidstoffsorte - Serie offen Execution: T Material specification: catalogue dependent FAQ What materials is this insert suitable for? Material suitability should be verified in the manufacturer’s product matrix; the WCGT030204-X25 WK1 is an uncoated carbide grade intended for general-purpose use, but specific workpiece recommendations depend on the application. Can the Trigon 80° geometry be used in interrupted cuts? The Trigon 80° form and a 0.4 mm corner radius provide edge robustness that can tolerate moderate interruptions; final suitability must be confirmed against the intended cutting conditions and toolholder rigidity. How does the chipbreaker X25 affect performance? The chipbreaker X25 is designed to promote controlled chip formation and evacuation during drilling and boring, reducing the risk of chip-related stoppages and improving process reliability for compatible setups. Is the WK1 grade coated or uncoated? WK1 is supplied as an uncoated carbide grade; this typically offers toughness and predictable wear patterns, but users should consult the product matrix for optimal cutting parameters. Are there alternative insert sizes or thicknesses available in this series? The series includes multiple insert sizes and thickness codes; for matching holders and alternative geometries, consult Metav Werkzeuge or the manufacturer’s catalogue. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand: Walter Tools) is part of the Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Mention of brand names serves explanation purposes only; the item offered concerns original, factory-new products from the manufacturer.
WCGT030204-X5 WAK15 Wendeplatten - Walter Tools
Take advantage of the combination of precise geometry, dedicated chip control and material-specific grade for efficient aluminium machining; order directly via Metav Werkzeuge or consult our specialists for process optimisation. WCGT030204-X5 WAK15 indexable insert for drilling/boring (Walter Tools) The WCGT030204-X5 WAK15 is an indexable insert engineered for high-performance drilling and boring in aluminium and other non‑ferrous metals. WAK15 uncoated carbide for non‑ferrous metals Trigon 80° geometry for stable cutting X5 chipbreaker and 7° clearance angle Increased productivity for non‑ferrous machining The WCGT030204-X5 WAK15 grade is designed specifically for machining aluminium and similar materials, delivering reliable metal removal with reduced adhesion. The combination of an uncoated carbide matrix and a sharp cutting edge supports high feed rates while keeping burr formation minimal. For production environments, this means shorter cycle times and fewer interruptions for tool cleaning, contributing directly to a more efficient machining process and consistent part quality. Geometry that improves surface finish and tool life The Trigon 80° form with a corner radius of 0.4 mm and a 7° clearance angle provides a stable cutting line and predictable engagement in drilling or boring operations. The X5 chipbreaker promotes controlled chip formation and evacuation, preventing chip packing and reducing the risk of built-up edge. These geometric decisions improve the surface finish and reduce flank wear, translating into longer intervals between indexings and steady performance over many cycles. Practical use and system compatibility Belonging to the Walter N‑Sortensystem, this insert is compatible with common Walter toolholders and clamping systems, simplifying tool management on the shop floor. Its designation as suitable for the ISO N group confirms its intended use for non‑ferrous metals such as aluminium, copper and brass, where sharp edges and low friction are advantageous. The insert’s X5 chip control and the uncoated composition make it particularly effective where material adhesion would otherwise degrade cutting action. For technical advice on Walter Tools inserts or to request cutting data for the WCGT030204-X5 WAK15, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — our specialists will advise on the best grade and geometry for aluminium machining Technical data SKU: WCGT030204-X5-WAK15-WALTER Model: WCGT030204-X5 WAK15 Product type: Indexable insert for drilling/boring Brand: Walter Tools Core figures Clearance angle: 7° Corner radius: 0.4 mm Insert size: 03 Thickness designation: 02 Plate form: Trigon 80° Material suitability / Features Grade: WAK15 (uncoated carbide) Chipbreaker: X5 Series: Walter N‑Sortensystem Application: Aluminium and non‑ferrous metals Execution: T FAQ What materials is this insert intended for? The WCGT030204-X5 WAK15 insert is intended for aluminium and other non‑ferrous metals; its uncoated carbide and X5 chipbreaker reduce adhesion during machining. How does the Trigon 80° form benefit drilling operations? The Trigon 80° geometry offers stable cutting engagement and supports consistent tool life and surface quality when using the WCGT030204-X5 WAK15 insert in drilling or boring cycles. Is this insert part of a system for easy replacement and inventory control? Yes, the insert belongs to the Walter N‑Sortensystem, which ensures compatibility with Walter toolholders and simplifies ordering and inventory management. Can this insert be used for stainless steel? The WAK15 grade is optimised for ISO group N (non‑ferrous metals); it is not specified for stainless steel applications and alternative grades should be selected for ferrous or hardened materials. Manufacturer: Walter Tools; Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
WCGT030204-X5 WTP35 Wendeplatten - Walter Tools
Take advantage of the combination of a robust WTP35 coated-carbide grade, precise 80° trigon geometry and effective X5 chip control for stable drilling and boring operations; order the insert directly via Metav Werkzeuge or consult the specialists if further application guidance is required. WCGT030204-X5 WTP35 — drilling/boring indexable insert by Walter Tools (Trigon 80°, coated carbide) WCGT030204-X5 WTP35 is a hardmetal indexable insert designed for drilling and bore-enlarging operations in production environments 80° trigon geometry for stable cutting 0.4 mm corner radius for defined edge strength 7° clearance angle to reduce rubbing Coated carbide grade WTP35 for versatile machining Consistent hole quality from geometry and edge control The 80° trigon shape combined with a 0.4 mm corner radius delivers consistent cutting engagement and improved edge robustness in interrupted or deep-hole cuts. The X5 chipbreaker assists in controlled chip formation, reducing the risk of long, stringy chips that can compromise surface finish and tool life. This geometry is particularly beneficial where dimensional repeatability and hole integrity matter most; the insert’s tolerance class G supports predictable fit in standard tool holders. By focusing on geometry and chip control, the insert promotes reliable cycle times and fewer rework operations. Coated grade engineered for broad-shop use and productivity The insert carries the WTP35 designation — a coated hardmetal grade from Walter Tools that balances wear resistance and toughness for general machining tasks. Although specific material suitability should be verified against the product matrix, the coated substrate aims to extend edge life under typical drilling and enlarging workloads. For workshops seeking an economical combination of performance and longevity, the coated grade offers improved wear protection while maintaining cutting-edge stability, which in turn contributes to better surface quality and less frequent index changes. Practical fitment and process integration for production workflows Marked as WCGT030204-X5, this insert matches common drilling/boring toolholders that accept Trigon 80° plates; plate size and thickness are indicated in the designation to ensure compatibility with existing tool systems. The defined 7° clearance reduces flank contact, lowering heat generation and helping maintain dimensional accuracy over longer runs. For implementation, check holder compatibility and the manufacturer’s matrix to confirm optimal cutting parameters. Shops integrating this insert can expect improved uptime through consistent performance and predictable wear patterns, aiding planning for index changes and inventory management. For toolrooms prioritising repeatable hole quality with Walter Tools' WTP35 grade, contact Metav Werkzeuge for tailored application advice or to arrange supply and optimisation support. Technical data Article number: WCGT030204-X5-WTP35-WALTER Name: Bohr-/Aufbohrwendeschneidplatte WCGT030204-X5 WTP35 Walter Tools Manufacturer: Walter Tools Product type: Bohr-/Aufbohrwendeschneidplatte ISO designation: WCGT030204-X5 WTP35 Facts Plate form: Trigon 80° Corner radius: 0.4 Clearance angle: 7° Plate size: 03 Plate thickness: 02 Tolerance class: G Special features Coating/grade: WTP35 Chipbreaker: X5 Series: Walter Schneidstoffsorte - Serie offen Material: Katalogabhängig Note: Verify workpiece-material suitability with the product matrix FAQ What materials is this insert intended for? The WCGT030204-X5 WTP35 insert uses a WTP35 coated hardmetal grade; material suitability should be checked in the product matrix to confirm applicability to specific workpiece materials. How does the X5 chipbreaker improve drilling performance? The X5 chipbreaker promotes controlled chip segmentation during drilling and boring, helping to avoid long chips and supporting safer, more consistent hole-making performance with reduced risk of surface damage. Is the insert compatible with standard Trigon 80° holders? The insert’s Trigon 80° shape and designation indicate compatibility with holders designed for 80° trigonal plates; verify holder fit and clamping specifications before assembly. What does the tolerance class G indicate? Tolerance class G refers to the manufacturing precision of the insert, supporting predictable seating and repeatable positioning in the toolholder for accurate machining results. Can the coated grade extend tool life in production use? The WTP35 coating is intended to enhance wear resistance and robustness, which typically contributes to extended index life under standard drilling and bore-enlarging conditions; final performance depends on cutting data and workpiece material. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are used here for identification and explanatory purposes only and do not imply any affiliation with our company. The offered item is an original, factory-new product of the manufacturer Walter Tools.
WCGT030204-X5 WXM15 Wendeplatten - Walter Tools
Take advantage of the combination of reliable chip control, a geometry optimised for non-ferrous materials, and the cost-efficiency of an uncoated carbide grade to keep production steady and predictable. Order the WCGT030204-X5 WXM15 insert directly via Metav Werkzeuge or ask our consultants if needed. WCGT030204-X5 WXM15 – Trigon 80° indexable insert for machining non-ferrous metals, Walter Tools The WCGT030204-X5 WXM15 is a Trigon 80° indexable insert engineered for efficient, low-adhesion machining of non-ferrous metals in the Walter N-series. Trigon 80° geometry for stable cutting Uncoated carbide grade WXM15 for NE-metals 7° clearance angle reduces friction X5 chipbreaker for controlled chip formation Stable corners and reliable edge for non-ferrous work The Trigon 80° form and 0.4 mm corner radius provide a balance between robustness and precision, improving edge life during interrupted cuts. As an uncoated carbide grade, WXM15 reduces the tendency for material adhesion when machining non-ferrous metals such as aluminium, copper, and Messing, which in turn lowers rework and tool-change frequency. This geometry supports consistent surface quality while maintaining predictable tool life under typical shop-floor conditions. Controlled chips and smoother production cycles The integrated X5 chipbreaker works together with the insert’s geometry to produce short, manageable chips and prevent long stringy swarf that interrupts automated feeding or manual handling. The combination of 7° clearance angle and the chip control geometry reduces friction at the cutting edge, helping to avoid built-up edge formation and delivering a more constant cutting force. The result is fewer stoppages and easier chip evacuation for dependable cycle times. Optimised for non-ferrous applications and system compatibility Designed for use with holders that accept the WCGT030204 series, the insert belongs to the Walter N-Sortensystem, offering straightforward replacement and series consistency. The uncoated WXM15 grade is particularly suited to NE-material groups according to ISO 513; the construction minimises adhesion and supports high-quality finishes on softer alloys. The tolerance class G and execution T signal consistent manufacturing precision and interchangeability within compatible tool systems. Practical benefits for the workshop With a compact plate size (03) and plate thickness (02), the insert delivers the expected combination of rigidity and accessibility for close-tolerance work. The design focuses on two clear benefits: improved process reliability through stable chip behaviour, and reduced secondary finishing thanks to smoother surface results. For production environments working primarily with aluminium, copper, and Messing, this insert offers a practical route to steady productivity without introducing specialised coatings. Contact Metav Werkzeuge today for tailored application advice and supply of Walter Tools WCGT030204-X5 WXM15 inserts. Technical Data SKU: WCGT030204-X5-WXM15-WALTER Name: Bohr-/Aufbohrwendeschneidplatte WCGT030204-X5 WXM15 Manufacturer: Walter Tools Series: Walter N-Sortensystem Grade: WXM15 Facts Clearance angle: 7° Corner radius: 0.4 mm Plate form: Trigon 80° Plate size: 03 Plate thickness: 02 Chipbreaker: X5 Tolerance class: G Execution: T Special features Uncoated carbide grade WXM15 Application group: non-ferrous metals (N) Designed for controlled chip formation Compatible with Walter N-series holders Compact geometry for precision machining FAQ Which materials is the insert suitable for? The WCGT030204-X5 WXM15 insert is specified for non-ferrous metals and performs particularly well on aluminium, copper, and Messing as defined in the Walter N-series guidance. Is the cutting grade coated or uncoated? The grade WXM15 is an uncoated carbide intended to reduce material adhesion when machining NE-materials. What benefit does the Trigon 80° form provide? The Trigon 80° form increases cutting stability and supports robust edge performance, which helps maintain surface quality during extended runs with the WCGT030204-X5 insert. How does the X5 chipbreaker affect machining? The X5 chipbreaker creates short, controllable chips that ease handling and reduce the risk of swarf-related interruptions, improving overall process reliability. Is this insert part of a recognised system? Yes, the insert is part of the Walter N-Sortensystem, enabling consistent replacement and series-wide interchangeability for compatible toolholders. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen belongs to the group of leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners and are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is original and brand-new.
WCGT040202-FM2 WSM21 T Wendeplatten - Walter Tools
Benefit from the combination of a heat‑resistant WSM21 coating and the FM2 chipbreaker for controlled chips and longer tool life; the Trigon 80° geometry and 0.2 mm corner radius deliver a balance of positive cutting action and edge stability for reliable production. Order the inserts directly via Metav Werkzeuge or consult our specialists for application advice. WCGT040202-FM2 WSM21 – Trigon 80° indexable insert for boring and turning, Walter Tools A WCGT040202-FM2 WSM21 indexable insert engineered for secure chip control and durable cutting when machining rostfreier Stahl and high‑temperature superalloys in boring and turning operations Coated carbide grade WSM21 FM2 chipbreaker for stable chip control Trigon 80° geometry for positive cutting Suited to rostfreier Stahl and superalloys Higher throughput through material‑specific coating and edge stability The combination of a coated carbide grade designed as WSM21 and a robust insert form produces measurable productivity gains when tackling difficult‑to‑cut materials. The coating supports thermal resistance and helps maintain a sharp cutting edge under the high temperatures typical of machining rostfreier Stahl and heat‑resistant superalloys. Because the grade is optimised for such alloys, tool life is extended and changeover frequency is reduced, which lowers process interruptions and contributes directly to improved output efficiency. Consistent surface quality with controlled chip formation Chip control is central to predictable turning and boring cycles. The FM2 chipbreaker, paired with the Trigon 80° form and a 0.2 mm corner radius, promotes short, manageable chips and stable cutting forces. This geometry reduces built‑up edge formation while delivering a consistent cutting action that supports repeatable surface finish. For operations where tool access and clearance are constrained, the positive rake and compact corner aid in achieving dimensional accuracy without compromising edge life. Practical application and mounting considerations for dependable results The insert’s relief of 7° and standard size/thickness codes allow straightforward integration into common toolholders designed for Trigon inserts; selection of the correct holder and clamping torque ensures the intended performance. The plate is available in size code 04 with thickness code 02 and tolerance class G, providing predictable mechanical fit‑up in indexable tool systems. For adaptations to specific cycles or atypical alloys, Metav Werkzeuge offers application guidance and cutting data to match the insert’s properties with feed, speed and depth settings appropriate for the workpiece and machine capability. Contact Metav Werkzeuge today for application guidance and to secure original Walter Tools WCGT040202-FM2 WSM21 inserts for machining rostfreier Stahl and superalloys Technical data SKU: WCGT040202-FM2-WSM21-WALTER Designation: WCGT040202-FM2 ISO designation: WCGT040202-FM2 WSM21 Manufacturer / Brand: Walter Tools Product type: Boring/turning indexable insert Grade: WSM21 Series: Walter Schneidstoffsorte - Serie offen Tolerance class: G Chipbreaker: FM2 Plate form: Trigon 80° Size code: 04 Thickness code: 02 Corner radius: 0.2 Relief angle: 7° Numbers / Core technical data Corner radius: 0.2 mm Relief angle: 7° Size code: 04 Thickness code: 02 Design / Special features Coated carbide (WSM21) FM2 chipbreaker for controlled chips Trigon 80° geometry Suitable for rostfreier Stahl (M) and superalloys/titanium (S) Tolerance class G Series: Walter Schneidstoffsorte - Serie offen FAQ What materials is this insert designed for? This insert is intended for rostfreier Stahl and heat‑resistant superalloys (material groups M and S); the WSM21 grade provides thermal stability and a stable cutting edge for these alloys. How does the FM2 chipbreaker influence machining? The FM2 chipbreaker produces short, controllable chips and reduces built‑up edge, improving surface finish and operational reliability when using the WCGT040202-FM2 WSM21 insert. Which geometry benefits are delivered by the Trigon 80° form? The Trigon 80° form offers a positive cutting action with good access in bore and turn applications, supporting stable cutting forces and repeatable dimensional accuracy. Is this insert compatible with standard Trigon toolholders? Yes; the insert’s size code 04 and thickness code 02 are compatible with standard toolholders designed for Trigon inserts, provided the correct clamping and seating procedures are followed. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Manufacturer/Responsible: AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden, support.coromant@sandvik.com
WCGT040202-FN2 WNN10 Wendeplatten - Walter Tools
Take advantage of the combination of coated carbide WNN10, a precise FN2 chipbreaker and the robust Trigon 80° geometry for consistent metalcutting performance; order via Metav Werkzeuge or request expert guidance from their consultants. WCGT040202-FN2 WNN10 drilling/boring and turning indexable insert by Walter Tools — Trigon 80°, 7° clearance WCGT040202-FN2 WNN10 is an indexable insert optimised for drilling, boring and light turning tasks where repeatable chip control and predictable wear behaviour are required Trigon 80° geometry for robust cutting FN2 chipbreaker for reliable chip control Coated carbide grade WNN10 for versatile use 7° clearance and 0.2 mm corner radius High-performance cutting with predictable results The insert is manufactured in a coated carbide grade (WNN10) designed for broad application ranges. Its Trigon 80° shape and FN2 chipbreaker enable controlled chip formation, which reduces the risk of workpiece damage and machine downtime. Because the grade is a coated hardmetal, wear resistance is improved and tool life is extended under a variety of cutting conditions. The combination of 7° clearance and a 0.2 mm corner radius produces a stable cutting edge that balances strength with surface finish, making the component suitable for mixed production environments where consistency is crucial. Practical benefits for process reliability and productivity The geometry and chipbreaker of the insert are chosen to promote efficient evacuation of chips and to limit chatter on interrupted cuts. As a result, cycle times are often shortened and scrap rates fall. The insert’s design allows predictable edge wear; consequently, tool change intervals can be scheduled rather than reactive, which supports lean machining workflows. Technical teams will appreciate that the insert’s FN2 chip control reduces manual rework and improves surface integrity on common components. Where operator time and machine availability are premium factors, this solution supports measurable productivity gains. Easy specification and integration into existing toolsets Technical documentation and the ISO designation are straightforward: the insert is listed as WCGT040202-FN2 WNN10, with execution code T and a tolerance class G for consistent interchangeability. The grade and series are documented as Walter Schneidstoffsorte - Serie offen, and the material information is catalogue-dependent, which allows selection of the precise variant required for the application matrix. The compact profile and standard size make the insert compatible with many toolholders, enabling rapid replacement and minimal setup adjustment. For engineers seeking to harmonise tool performance across machines, this insert offers a pragmatic balance of longevity, chip control and geometric stability. For tailored recommendations on integrating this Walter Tools WNN10 insert into production, contact Metav Werkzeuge for expert advice and availability via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: WCGT040202-FN2-WNN10-WALTER Name: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte WCGT040202-FN2 WNN10 Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.2 mm Plate form: Trigon 80° Plate size: 04 Plate thickness: 02 Tolerance class: G Chipbreaker: FN2 Special features Grade: WNN10 (coated carbide) Series: Walter Schneidstoffsorte - Serie offen Execution: T Material: Catalogue-dependent ISO designation: WCGT040202-FN2 WNN10 UID: WCGT040202-FN2-WNN10-WALTER FAQ What materials is this insert suitable for? The insert’s WNN10 coated carbide grade is designed for a wide range of workpiece materials; the exact suitability should be checked against the product matrix for the intended application. How does the FN2 chipbreaker affect machining? The FN2 chipbreaker provides controlled chip formation and efficient evacuation, which improves surface quality and reduces the risk of recutting chips in mixed cutting operations. What does the Trigon 80° form mean for toolholders? The Trigon 80° geometry ensures a robust cutting edge and broad contact area; it is compatible with standard trigon toolholders designed for this insert size. Is the insert interchangeable with other brands’ equivalents? Interchangeability depends on holder specifications and tolerance class; the tolerance class G and ISO designation help determine compatibility with existing tooling. What is the significance of the 0.2 mm corner radius? A corner radius of 0.2 mm offers a compromise between edge strength and finish quality, suitable for applications needing both durability and acceptable surface integrity. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is an original, brand-new product from the manufacturer.
WCGT040202-X15 WAK15 Wendeplatten - Walter Tools
High-performance, uncoated carbide insert with Trigon 80° geometry and a 0.2 mm nose radius for sharp, low-adhesion cutting in aluminium and other non-ferrous metals; X15 chipbreaker and 7° clearance improve chip control and reduce rubbing. Order the WCGT040202-X15 WAK15 directly via Metav Werkzeuge or ask our consultants if needed. WCGT040202-X15 WAK15 Trigon 80° indexable insert for aluminium — Walter Tools The WCGT040202-X15 WAK15 is an indexable insert engineered for drilling and boring operations in aluminium and non-ferrous metals, combining a trigon cutting form with a specialised chipformer for controlled evacuation Trigon 80° cutting form WAK15 uncoated carbide grade X15 chipbreaker for non-ferrous metals 7° clearance angle for reduced rubbing Faster, cleaner aluminium machining through optimised geometry The combination of a Trigon 80° profile and an uncoated carbide substrate delivers a consistent, sharp cutting edge that is especially effective when machining aluminium and similar alloys. The insert’s geometry reduces the tendency for material to stick, so feed rates can be optimised while maintaining surface integrity. This results in shorter cycle times and fewer interruptions for rework, making the component suitable where productivity and part quality are priorities. The construction supports repeatable performance in serial production. Precise chip control and improved surface quality A dedicated X15 chipbreaker offers predictable chip formation and evacuation during drilling and boring, lowering the risk of chip packing and surface scoring. The 0.2 mm nose radius produces a controlled cutting contact that balances sharpness and edge strength, which benefits final surface finish. Combined with the 7° clearance angle, the design minimises rubbing and heat build-up at the flank, promoting dimensional accuracy and extending the usable life of the cutting edge under normal operating conditions. Simple integration into existing tool systems and stable results The insert is supplied in the Walter N-Sortensystem series and is compatible with standard toolholders that accept the WCGT shape and size code. Its consistent tolerances and the WAK15 grade enable reliable seat fit and repeatable run-out characteristics, which reduces set-up time and inspection demands. Given its role in non-ferrous machining, the insert supports process stability and eases tool selection for mixed-production environments where aluminium parts form a significant share. Material suitability and practical application notes Classified for group N (non-ferrous metals), the insert is intended for aluminium, copper and light alloys; the WAK15 grade is uncoated to avoid built-up edge commonly seen with sticky materials. In practice, light to moderate cutting fluids or air cooling are often sufficient; high-pressure coolant is rarely necessary for typical aluminium work. When used with the appropriate toolholder and cutting parameters, the insert contributes to consistent chip control and reduced burr formation, supporting downstream assembly or finishing operations. Contact Metav Werkzeuge today to specify the Walter Tools WCGT040202-X15 WAK15 for a machining setup optimised for aluminium and non-ferrous production. Technical data SKU: WCGT040202-X15-WAK15-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WCGT040202-X15 WAK15 Walter Tools Product type: Bohr-/Aufbohrwendeschneidplatte (indexable insert) Manufacturer: Walter Tools Series: Walter N-Sortensystem Grade: WAK15 ISO designation: WCGT040202-X15 WAK15 Execution: T Tolerance class: G Facts Clearance angle: 7° Corner radius: 0.2 mm Shape: Trigon 80° Size code: 04 Thickness code: 02 Chipbreaker: X15 Special features Uncoated carbide grade (WAK15) Suited for aluminium and other non-ferrous metals Designed for drilling and boring applications Stable chip control and low adhesion Part of Walter N-grade system FAQ What materials is this insert best suited for? The WCGT040202-X15 WAK15 is specified for aluminium and other non-ferrous metals; the WAK15 grade is an uncoated carbide designed to reduce built-up edge on these materials. How does the X15 chipbreaker affect performance? The X15 chipbreaker promotes predictable chip formation and evacuation, improving process stability during drilling and boring and helping to protect the work surface from scoring. Can the insert be used in standard toolholders for WCGT inserts? Yes, the insert follows the WCGT form and size code, allowing integration into compatible toolholders that accept Trigon 80° inserts with the corresponding seat geometry. Why choose an uncoated grade for aluminium? An uncoated carbide grade like WAK15 reduces the risk of chip adhesion that can occur with coatings; this keeps the cutting edge sharp and maintains surface quality when machining sticky, low-alloy materials. What role does the 0.2 mm nose radius play? The 0.2 mm nose radius balances edge sharpness and strength, enabling higher-quality surface finishes while retaining sufficient edge stability for common drilling and boring feeds. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and brand names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only. There is no affiliation between Metav Werkzeuge and the mentioned brands; the offered item is an original, factory-new product of the manufacturer.
WCGT040202-X15 WTP35 Wendeplatten - Walter Tools
Take advantage of the combination of trigon geometry, coated carbide WTP35, and precise chip control for consistent performance in drilling and boring operations; order directly via Metav Werkzeuge or consult the technical team for application-specific selection. WCGT040202-X15 WTP35 Trigon 80° indexable insert, 0.2 mm corner radius — Walter Tools The WCGT040202-X15 WTP35 is a trigon indexable insert engineered for drilling and boring tasks, offering a robust 80° seat, a 0.2 mm corner radius and a chipbreaker optimised for stable chip formation. Trigon 80° geometry for secure seating Coated carbide grade WTP35 for durability 0.2 mm corner radius for reliable edge strength 7° relief angle for smooth penetration Improved edge security and reliable chip control The trigon 80° geometry and 0.2 mm corner radius work together to provide enhanced edge stability during interrupted cuts and when entering the workpiece. The dedicated chipbreaker X15 channels chips away from the cutting zone, reducing the risk of built-up edge and enabling a predictable cutting action. This combination translates into fewer index changes and steadier cycle times on the machine, while the form of the insert supports secure clamping in standard drill and boring cutters. Longer tool life through a coated carbide grade The insert is produced in the WTP35 coated carbide grade, a Walter Tools composition designed to balance wear resistance and edge toughness. The coating reduces flank wear and improves performance under fluctuating temperatures, which is particularly useful for production environments seeking repeatable component quality. Material suitability should be verified against the specific product matrix for each application to ensure optimal selection; the coated carbide classification indicates a versatile, industrial-grade solution rather than a universal guarantee for all substrates. Practical fitment and machining behaviour for efficient processes With a modest 7° relief angle, the insert offers smooth penetration and reduced cutting forces in typical drilling and reaming cycles. The item corresponds to insert size code 04 and thickness code 02, facilitating straightforward replacement in systems that accept WCGT-style parts. The trigon form also provides multiple indexable positions, which can lower tooling costs per edge when compared with single-edge alternatives. For integration into a tooling system, verify seat compatibility and cutter clamping dimensions before assembly to maintain process stability. For reliable chip control and predictable performance with Walter Tools coated inserts, contact Metav Werkzeuge for application guidance or to place an order via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: WCGT040202-X15-WTP35-WALTER Designation: WCGT040202-X15 WTP35 Manufacturer: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Grade: WTP35 Shape: Trigon 80° Facts Free angle: 7° Corner radius: 0.2 mm Size code: 04 Thickness code: 02 Tolerance class: G Special features Coated carbide grade WTP35 Chipbreaker X15 Trigon 80° plate form Execution: T Base designation without grade: WCGT040202-X15 FAQ What is the primary advantage of the trigon 80° form? The trigon 80° form provides a secure seat in the cutter body and offers multiple indexable positions, improving edge utilisation and ensuring steady cutting performance with the WCGT040202-X15 WTP35 insert. How does the X15 chipbreaker affect machining? The X15 chipbreaker promotes controlled chip formation and evacuation, reducing heat concentration at the cutting edge and supporting consistent surface finishes when the WCGT040202-X15 WTP35 is used under recommended conditions. Which physical dimensions are relevant when specifying this insert? Key dimensions include the 0.2 mm corner radius, 7° free angle, shape Trigon 80°, size code 04 and thickness code 02; these determine seating, edge strength and fitment in compatible tooling. Is the WTP35 grade suitable for all materials? WTP35 is a coated carbide grade offering broad industrial utility; however, material suitability must be checked against the concrete product matrix for each application before final selection of the WCGT040202-X15 WTP35. Can this insert be used in both drilling and boring tools? Yes, the design is intended for drilling and boring indexable applications where the trigon seat and chipbreaker configuration match the cutter body; verify holder compatibility and seating details prior to fitting. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only; there is no affiliation between our company and the mentioned brands. The offered article is an original, factory-new product of the manufacturer.
WCGT040202-X15 WXM15 Wendeplatten - Walter Tools
Combining an uncoated carbide grade for very sharp cutting edges with a Trigon 80° geometry and a dedicated X15 chipbreaker delivers stable engagement and predictable chip control for non‑ferrous machining. Benefit from the fine 0.2 mm corner radius and 7° relief for improved surface finish and repeatable hole quality; order the inserts via Metav Werkzeuge or consult their specialists for application pairing and availability. WCGT040202-X15 WXM15 Drill/Boring Indexable Insert – Trigon 80°, for non‑ferrous metals, Walter Tools The WCGT040202-X15 WXM15 is a drill and bore‑enlargement indexable insert engineered for efficient machining of non‑ferrous metals such as aluminium, copper and brass, designed for use in Walter tool systems. Trigon 80° geometry for stable engagement Uncoated carbide grade WXM15 for sharp edges X15 chipbreaker for predictable chip control 7° relief and 0.2 mm corner radius for finish Faster, more consistent holemaking with optimised geometry The triangular Trigon 80° form and the moderate 7° relief combine to reduce radial run‑out and improve engagement stability when enlarging bores or finishing holes. Paired with the uncoated carbide WXM15 grade, the insert promotes a sharp cutting line that reduces burr formation and lowers cutting forces in non‑ferrous metals. The result is a more consistent cycle time and fewer rework operations, which supports higher net output in batch machining and component production environments. The design also assists in controlled insertion into pre‑drilled holes, improving concentricity and dimensional accuracy. Predictable chips and improved surface quality through chipbreaker design The integrated X15 chipbreaker is tailored for low‑adhesion materials and encourages short, controllable chips that evacuate reliably from the cutting zone. This reduces the risk of chip entanglement and tool damage during continuous runs. The modest 0.2 mm corner radius helps to blend the transition between cutting edge and flank, delivering improved surface finish without compromising edge strength. Together these features reduce downtime related to chip jams and rework, contributing to a safer, more productive machining process. Application suitability and system compatibility for efficient integration Formulated for non‑ferrous metals, the insert is part of the Walter N‑Sortensystem, where grade selection and geometry are matched to material behaviour—especially for aluminium alloys and copper‑based materials that demand low friction cutting edges. The WCGT040202‑X15 WXM15 fits standard Walter indexable‑insert drill and boring holders sized for this insert designation, enabling straightforward replacement and inventory management. For users seeking process stability and repeatable results in multi‑stage operations, the insert offers a pragmatic combination of sharpness and robustness. For application advice or stock enquiries regarding the Walter Tools WCGT040202‑X15 WXM15 inserts, contact Metav Werkzeuge (info@metav-werkzeuge.com / +49 2822 7131930) to discuss suitable holders and recommended cutting data. Technical Data Article number: WCGT040202-X15-WXM15-WALTER Designation: WCGT040202-X15 ISO designation: WCGT040202-X15 WXM15 Product type: Drill/Boring indexable insert Series: Walter N-Sortensystem Grade: WXM15 (uncoated carbide) Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.2 mm Plate form: Trigon 80° Plate size: 04 Plate thickness: 02 Tolerance class: G Special features Chipbreaker: X15 Intended material group: Non‑ferrous metals (N) Sorteneinsatz: NE‑metals (aluminium, copper, brass) Suitable for use in Walter toolholders for drilling and bore enlargement FAQ What materials is this insert best suited for? The WCGT040202‑X15 WXM15 is intended primarily for non‑ferrous metals such as aluminium, copper and brass, where the sharp uncoated carbide edge and X15 chipbreaker reduce material adhesion and improve evacuation. Is the insert coated or uncoated? This insert uses the WXM15 grade, an uncoated carbide formulation optimised for sharp edges and reduced friction in non‑ferrous machining. Which holder types accept this insert designation? The insert conforms to the common indexable insert designation and is compatible with Walter drill and boring holders designed for WCGT‑style triangular inserts; holder compatibility should be verified against toolholder documentation. How does the chipbreaker affect machining? The X15 chipbreaker produces predictable, short chips in soft and ductile materials, improving chip flow and reducing the risk of entanglement, which supports continuous production and reduces stoppages. Will this insert improve surface finish in holemaking? Yes, the combination of the 0.2 mm corner radius and the Trigon 80° geometry helps to produce a finer surface finish while maintaining edge strength during finishing passes. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanation only; there is no connection between our company and the named brands. The offered item is original, brand‑new goods from the manufacturer. Walter Tools (Walter AG) is a global provider of precision tools for metalworking and is part of the Sandvik Group; the brand is referenced solely to describe the origin of the product.
WCGT040202-X5 WAK15 Wendeplatten - Walter Tools
Take advantage of the combination of WAK15 grade performance, Trigon 80° seating and a precise 0.2 mm corner radius to achieve consistent results when machining aluminium and other non-ferrous metals; order directly via Metav Werkzeuge or contact our consultants for application advice. WCGT040202‑X5 WAK15 indexable insert — Trigon 80° for aluminium machining by Walter Tools A robust indexable insert designed for drilling and boring operations in aluminium and non‑ferrous materials, combining the Walter N‑grade concept with a chipbreaker tailored for controlled swarf evacuation WAK15 uncoated carbide for aluminium Trigon 80° form for secure seating 0.2 mm corner radius for fine finishes Chipbreaker X5 for controlled aluminium chips High efficiency for non‑ferrous production The WAK15 grade is an uncoated carbide formulation optimised for machining aluminium, offering low adhesion and reduced tendency for built‑up edge. The insert’s geometry provides a cutting face that supports stable chip control and lower friction, which translates into longer tool life and fewer interruptions for cleaning or rework. For manufacturers focused on repeatability and throughput, this means fewer stoppages and a more consistent process window when producing components from aluminium and similar non‑ferrous alloys. Precision seating and surface quality The Trigon 80° plate form with a 0.2 mm corner radius ensures a stable tool fit and predictable engagement at the cutting edge. The modest corner radius helps to balance edge strength with the ability to achieve a fine surface finish, particularly on thin‑walled or delicate workpieces. Combined with the specified clearance geometry, the insert reduces chatter risk and supports reliable dimensional control in series production, benefitting job shops and OEM supply chains that demand consistent part quality. Controlled swarf and process reliability The chipbreaker X5 is configured to break and evacuate aluminium swarf effectively, reducing clogging at the cutting zone and helping maintain cutting temperatures within acceptable limits. The relief geometry (7° nominal) supports smooth entry and exit, limiting edge rubbing and heat build‑up. These characteristics contribute directly to high productivity by enabling longer uninterrupted cuts and reducing the frequency of insert changes or secondary finishing operations. Application scope and practical guidance Designed under the Walter N‑grade system, the insert is suitable for a range of non‑ferrous work, mainly aluminium, copper and brass alloys. Its uncoated nature is deliberately chosen to avoid coating‑related adhesion on softer metals; this promotes cleaner chips and lowers the risk of material sticking to the edge. For best results, combine this insert with appropriate feed rates and coolant strategies for aluminium machining, ensuring stable clamping and correct toolholder alignment to exploit the insert’s advantages fully. Contact Metav Werkzeuge today for specification matching, stock availability and rapid delivery of Walter Tools inserts — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: WCGT040202-X5-WAK15-WALTER Designation: WCGT040202-X5 WAK15 Product type: drilling/boring indexable insert Facts Plate form: Trigon 80° Grade: WAK15 (uncoated carbide) Material group: N (non‑ferrous metals) Special features Chipbreaker: X5 Corner radius: 0.2 mm Relief angle: 7° Series: Walter N‑Sortensystem Plate size: 04 Plate thickness: 02 Tolerance class: G Manufacturer: Walter Tools FAQ Is this insert suitable for aluminium machining? Yes. The WCGT040202‑X5 WAK15 insert is specifically designed for aluminium and other non‑ferrous metals, using the WAK15 uncoated carbide grade to reduce material adhesion. Does the insert have a coating? No. The insert uses an uncoated carbide grade (WAK15), which is advantageous for machining soft, adhesive metals such as aluminium. What benefit does the Trigon 80° form provide? The Trigon 80° geometry offers a secure seating and cut engagement that improves stability and repeatability during drilling and boring operations. How does the chipbreaker X5 improve production? The chipbreaker X5 breaks and directs aluminium swarf for reliable evacuation, reducing clogging and helping to maintain consistent cutting conditions. Which series and system does this insert belong to? This insert is part of the Walter N‑Sortensystem, developed for non‑ferrous applications and tailored cutting behaviour. The Walter AG (brand appearance: Walter Tools), headquartered in Tübingen, is among the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned solely for explanatory purposes; there is no affiliation between our company and the named manufacturers. The offered item is an original, factory‑new product from the manufacturer.
WCGT040202-X5 WK1 Wendeplatten - Walter Tools
Benefit from the Trigon 80° geometry and the X5 chipbreaker combined with the robust WK1 uncoated cemented carbide to achieve stable engagement and consistent chip formation in drilling and boring operations; order the WCGT040202-X5 WK1 insert directly via Metav Werkzeuge or ask our consultants if needed WCGT040202-X5 WK1 drilling/boring indexable insert by Walter Tools — Trigon 80°, X5 chipbreaker The WCGT040202-X5 WK1 is an uncoated cemented carbide indexable insert designed for drilling and boring applications where stable cut entry and controlled chip flow are required Trigon 80° geometry for stable tool engagement X5 chipbreaker for controlled chip formation 7° clearance angle for reduced friction Uncoated cemented carbide - WK1 grade Stable engagement and reliable chip control for boremaking The Trigon 80° configuration delivers a larger engagement area compared with sharper-point inserts, which increases axial stability and reduces vibration during entry. Combined with the X5 chipbreaker, this geometry actively fragments and directs chips away from the cutting zone, enhancing process reliability. The described features support longer uninterrupted cycles and more consistent hole quality, while the modest 0.2 mm corner radius helps to blunt the cutting edge slightly, reducing the risk of corner chipping on interrupted cuts. Technical terms: a chipbreaker is a shaped land on the insert face that alters chip flow; the corner radius distributes cutting loads and improves edge strength. Grade and material considerations for predictable tool life The cutting grade WK1 is specified as an uncoated cemented carbide. Uncoated carbide grades are often chosen for their predictable wear behaviour and for applications where coating adhesion is critical or where secondary coatings would alter cutting geometry. The choice of grade makes this insert suitable for a range of conventional machining tasks; however, material suitability should be verified against the product matrix for specific workpiece materials and machining parameters. The combination of geometry and grade aims to balance wear resistance with fracture toughness to maintain consistent edge condition over repeated cycles. Practical handling, mounting and process recommendations The insert’s 7° clearance angle reduces flank contact and lowers frictional heat at the tool–workpiece interface, which can extend tool life under moderate feeds and speeds. The Trigon 80° form facilitates straightforward seating in compatible drill or boring heads; correct torque and secure clamping are essential to fully benefit from the insert’s stability. For optimised results, select feeds and spindle speeds according to the chosen workpiece material and refer to the tooling system’s recommended parameters. For complex materials or high-demand cycles, consult the tooling matrix to confirm whether prehardened or exotic alloys are appropriate for this uncoated grade. For tailored selection, stock information and availability of Walter Tools inserts such as the WCGT040202-X5 WK1, please contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 for expert advice and rapid assistance Technical data Article number: WCGT040202-X5-WK1-WALTER Designation: WCGT040202-X5 WK1 Product type: Bohr-/Aufbohrwendeschneidplatte Manufacturer: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Facts Clearance angle: 7° Corner radius: 0.2 mm Insert shape: Trigon 80° Size code: 04 Thickness code: 02 Tolerance class: G Special features Chipbreaker: X5 Grade: WK1 (uncoated cemented carbide) Execution: T Material specification: Katalogabhängig Sorts and series note: Check product matrix for workpiece suitability FAQ What is the primary application for this insert? The WCGT040202-X5 WK1 indexable insert from Walter Tools is designed for drilling and boring operations where stable entry and controlled chip evacuation are priorities; it suits applications that benefit from Trigon 80° geometry and an active chipbreaker. Which materials is the WK1 grade suitable for? The WK1 grade is an uncoated cemented carbide; material suitability depends on the machining matrix—consult the product matrix to confirm compatibility with specific materials and hardness levels. How does the X5 chipbreaker affect machining? The X5 chipbreaker promotes manageable chip formation and evacuation, reducing the likelihood of long, stringy chips and improving process stability during holemaking. Are there special mounting requirements for the Trigon 80° insert? The Trigon 80° shape requires a compatible seat in the drill or boring head and correct clamping torque to ensure stability; proper toolholder maintenance and secure fastening are recommended to exploit the insert’s geometry. Is the WCGT040202-X5 WK1 coated? No, the specified grade WK1 is an uncoated cemented carbide; coating information is not listed and should be verified if a coated variant is required Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers Walter Tools.
WCGT040202-X5 WTP35 Wendeplatten - Walter Tools
Combining the WTP35 coated-carbide grade with a Trigon 80° geometry and a 0.2 mm corner radius delivers stable chip formation and consistent tool life for drilling and boring operations; order the insert directly via Metav Werkzeuge or consult our specialists for material-specific process data. WCGT040202-X5 WTP35 — Drill/Boring indexable insert, Trigon 80°, 7° relief — Walter Tools The WCGT040202-X5 WTP35 is a coated-carbide indexable insert engineered for drilling and boring tasks where controlled chip evacuation and repeatable bore quality are required. High-performance coated carbide WTP35 Trigon 80° geometry for stability 7° relief angle for positive cutting 0.2 mm corner radius for edge strength Productivity gains from Trigon geometry and chip control The Trigon 80° form offers a robust cutting profile that reduces vibration in interrupted cuts and enhances axial stability in bore operations. Combined with the X5 chipbreaker, this geometry promotes consistent chip segmentation and evacuation, which reduces rework and increases throughput. Emphasis on repeatability means fewer tool changes and less downtime, supporting higher process efficiency on production lines that demand steady cycle times and predictable results. Durable cutting performance with the WTP35 grade The WTP35 composition is a coated carbide grade optimised by Walter for general drilling and boring applications; it is designed to provide stable chip formation and good wear resistance. The coating enhances edge robustness and thermal stability under continuous cutting, enabling reliable performance across a range of common workpiece materials. For planners and production engineers this translates into predictable tool life and easier integration into existing cutting data tables when compared with uncoated alternatives. Precision edge geometry for bore quality and tool life A 7° relief angle and a 0.2 mm corner radius balance sharpness and mechanical strength at the cutting edge. The moderate relief angle ensures positive cutting action with controllable feed forces, while the corner radius supports a durable cutting edge that resists chipping in cyclic loads. With tolerance class G and the Trigon plate form, dimensional consistency is maintained, helping to achieve reproducible bore diameters and improved surface finish in serial production. Practical selection and application guidance Selection should be aligned with the intended workpiece material and the machine’s rigidity: consult the provided material matrix to confirm suitability for specific alloys. The indexable insert’s coated carbide chemistry and the X5 chipbreaker make it a solid choice for general-purpose drilling and light roughing, but application-specific testing is recommended for non-standard alloys or high-temperature conditions. When process optimisation is necessary, the combination of geometry and grade supports steady improvements in cycle economy and overall machining quality. Contact Metav Werkzeuge for tailored cutting-data sheets and application advice on Walter WTP35 inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 for specialist consultation Technical Data SKU: WCGT040202-X5-WTP35-WALTER Name: WCGT040202-X5 WTP35 Type: Drill/Boring indexable insert Manufacturer: Walter Tools Material designation: Katalogabhängig Grade family: Walter Schneidstoffsorte - Serie offen Facts Relief angle: 7° Corner radius: 0.2 mm Plate form: Trigon 80° Plate size: 04 Plate thickness: 02 Tolerance class: G Special features Chipbreaker: X5 Grade: WTP35 (coated carbide) Execution: T ISO designation: WCGT040202-X5 WTP35 Base designation: WCGT040202-X5 FAQ What machining tasks is this insert optimised for? The insert is optimised for drilling and boring operations where controlled chip formation and stable cutting are priorities; the WCGT040202-X5 WTP35 grade emphasises productive machining with consistent tool life. Which materials can be machined with this grade? The WTP35 grade is a coated carbide designed for a broad workpiece spectrum; users should check the product matrix to confirm suitability for specific materials before series use. How does the 0.2 mm corner radius affect bore finish? A 0.2 mm corner radius increases edge strength and reduces the risk of chipping, contributing to consistent bore diameters and improved surface finish during serial production when using the WCGT040202-X5 WTP35 insert. Is the X5 chipbreaker suitable for interrupted cuts? Yes, the X5 chipbreaker is intended to promote reliable chip control and segmentation, which supports interrupted cuts and enhances chip evacuation in drilling and boring operations. Manufacturer/Responsible: Walter Tools / AB Sandvik Coromant, Mossvägen 10, 811 34 Sandviken, Sweden; support.coromant@sandvik.com Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are used for explanatory purposes only and do not imply any affiliation between Metav Werkzeuge and the trademark owners. The offered item is an original, factory-new product of the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com