WCGT040204-FM2 WSM21 FM2 Wendeplatten - Walter Tools
Take advantage of the combination of a heat-resistant, coated carbide grade and a secure FM2 chipbreaker for uninterrupted machining of demanding materials; order directly via Metav Werkzeuge or consult our specialists for application-matched recommendations. WCGT040204-FM2 WSM21 Drilling/Boring and Turning indexable insert — Trigon 80°, FM2 chipbreaker, Walter Tools The WCGT040204-FM2 WSM21 is a trigon 80° indexable insert designed for drilling, boring and turning in demanding alloys, optimised for stainless steels and heat-resistant superalloys. Walter grade WSM21, coated carbide Trigon 80° form with 0.4 mm corner radius FM2 chipbreaker for secure chip control 7° clearance angle, suitable for stainless steel Boosted productivity through stable chip formation The combination of the WSM21 coated carbide grade and the FM2 chipbreaker delivers a measurable improvement in process stability when machining ductile and heat‑resistant materials. The coating enhances thermal resistance while the chipbreaker geometry promotes controlled chip segmentation, which reduces downtime from chip entanglement and stabilises cutting forces. This results in a more consistent material removal rate and fewer interrupted cycles, making the insert particularly suitable for series production where run-to-run repeatability is crucial. The design supports efficient heat management, contributing directly to predictable tool life and lower overall machining costs. Improved surface finish and predictable cutting edge life The Trigon 80° insert form with a 0.4 mm corner radius and a 7° clearance angle is configured to balance strength and finish: the sharper corner radius assists in achieving finer surface qualities on internal and external contours, while the clearance angle minimises rubbing and reduces built-up edge formation when working with stainless steels. Coated cemented carbide substrate properties conserve the integrity of the cutting edge under elevated temperatures typical of machining superalloys and titanium grades. For operators less familiar with these terms: the corner radius influences both strength and finish, and the clearance angle determines how cleanly the insert disengages from the workpiece. Versatile application and economical integration in tooling systems This insert is intended for use in both drilling/boring and turning tool families, enabling shops to standardise on a single grade across multiple operations. The insert’s WCGT040204-FM2 designation denotes the trigon geometry and size variants compatible with common tool holders, facilitating quick index changes and minimal machine downtime. By choosing a grade optimised for stainless steel and heat-resistant alloys, procurement benefits from broader material coverage and improved stock rationalisation. Application-specific consultation can match the insert to the correct holder and cutting parameters to extract the best balance of material removal rate and tool life. Discuss application requirements with Metav Werkzeuge for optimised tool selection and fast availability; Metav Werkzeuge provides technical advice and fast delivery — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data Article number: WCGT040204-FM2-WSM21-WALTER Product type: Drilling/Boring and Turning indexable insert Designation: WCGT040204-FM2 WSM21 Manufacturer: Walter Tools Grade: WSM21 Facts Clearance angle: 7° Corner radius: 0.4 mm Insert size: 04 Plate thickness: 02 Form: Trigon 80° Tolerance class: G Special features Substrate: coated cemented carbide Chipbreaker: FM2 Suitable for: stainless steel (M) Also suitable for: heat-resistant superalloys and titanium (S) Application: drilling, boring, turning Series: Walter Schneidstoffsorte - Serie offen FAQ Is this insert suitable for machining stainless steel? Yes. The WCGT040204-FM2 WSM21 insert is specified for stainless steel applications (material group M) and is optimised to reduce built-up edge and improve chip control. Can the insert be used for heat-resistant superalloys or titanium? The WSM21 grade and the FM2 chipbreaker are designed to handle heat-resistant superalloys and titanium (material group S), offering improved thermal resistance and edge stability for these demanding materials. What benefits does the FM2 chipbreaker provide in continuous turning operations? The FM2 chipbreaker ensures controlled chip segmentation and reliable chip evacuation, which reduces machine stoppages and supports consistent cutting forces during extended production runs. How does the Trigon 80° geometry affect toolholder compatibility? The Trigon 80° form follows common industry geometries for trigon inserts, allowing straightforward integration with compatible toolholders specified for WCGT-style inserts. Is the WCGT040204-FM2 part of an open series or a specialised family? This insert belongs to the Walter Schneidstoffsorte - Serie offen, providing a versatile solution across a broad range of materials and geometries. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany
WCGT040204-FN2 WNN10 Wendeplatten - Walter Tools
Benefit from the combination of coated carbide WNN10, Trigon 80° geometry and the FN2 chipbreaker for controlled chips and reliable tool life; order directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. WCGT040204-FN2 WNN10 – Trigon 80° indexable insert with FN2 chipbreaker by Walter Tools The WCGT040204-FN2 WNN10 is an indexable insert designed for drilling, boring and turning applications, combining a Trigon 80° form with a FN2 chipbreaker to support consistent chip control in a range of machining tasks Trigon 80° insert geometry Coated carbide grade WNN10 FN2 chipbreaker for stable chips 0.4 mm corner radius, 7° clearance High machining performance through geometry and grade The Trigon 80° geometry together with the WNN10 coated carbide provides a balanced compromise between strength and cutting-edge sharpness. This combination reduces cutting forces in interrupted cuts and supports stable engagement in axial operations, which in turn improves tool life and process reliability. The FN2 chipbreaker is engineered for repeatable chip formation, promoting uninterrupted production sequences and minimising the need for secondary chip handling. Where material suitability is crucial, the sort specification recommends consulting the manufacturer’s product matrix before application to ensure optimal results. Design details that explain the practical benefits A modest 0.4 mm corner radius ensures robust edge support while preserving acceptable surface finish in many turning and boring tasks; the 7° clearance angle reduces rubbing on the flank and helps maintain cutting stability. The insert’s Trigon form offers three cutting edges per indexation, enabling economical use of each insert and simplified tool setting. The coated carbide composition, identified by the WNN10 designation, gives wear resistance and heat tolerance typical of coated grades; however, specific workpiece compatibility should be verified against the provided grade chart to match process parameters and expected component tolerances. Application efficiency and process reliability in production In production environments where repeatability and predictable tool life are priorities, the combination of geometry, chip control and a proven carbide grade supports consistent output and reduced downtime. The insert is released in the Walter Schneidstoffsorte series and is produced to tolerance class G, which contributes to stable seating and repeatable positioning in toolholders. For users seeking predictable economics, predictable wear behaviour and straightforward indexation, this insert is suitable as part of a wider machining strategy—bearing in mind that the exact workpiece materials for which it is optimised should be checked in the product matrix supplied by the manufacturer. Contact Metav Werkzeuge for detailed cutting data, availability and personalised recommendations for Walter Tools inserts; Metav Werkzeuge’s specialists are available by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: WCGT040204-FN2-WNN10-WALTER Designation: WCGT040204-FN2 WNN10 Product type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Manufacturer: Walter Tools Core data Insert form: Trigon 80° Clearance angle: 7° Corner radius: 0.4 mm Plate size: 04 Plate thickness: 02 Tolerance class: G Special features Coating / grade: WNN10 (coated carbide) Chipbreaker: FN2 Series: Walter Schneidstoffsorte - Serie offen Execution: T Material specification: Katalogabhängig FAQ What types of machining is this insert intended for? The insert is intended for drilling, boring and turning operations; the WCGT040204-FN2 WNN10 from Walter Tools is designed to provide stable chip control in axial and radial engagements. Which grade is used and what does it mean for wear resistance? The grade is WNN10, a coated carbide class that delivers enhanced wear resistance and thermal stability compared with uncoated grades; users should consult the manufacturer’s matrix for the best match to specific workpiece materials. How does the FN2 chipbreaker affect machining? The FN2 chipbreaker promotes consistent chip formation and evacuation, reducing the likelihood of entanglement and supporting continuous operation with fewer interruptions. Is the insert suitable for all materials? Material suitability is not universal; the Walter Schneidstoffsorte series recommends checking the product matrix for the WNN10 grade to confirm compatibility with the intended materials and cutting conditions. How many cutting edges are available per insert? The Trigon 80° form provides three indexable cutting edges per insert, enabling economical use through multiple reindexes. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is an original, factory-new product of the manufacturer.
WCGT040204-MN2 WNN10 Wendeplatten - Walter Tools
Take advantage of a proven combination of precise geometry and a specialised chipbreaker to secure consistent machining results. The trigon 80° form with a 0.4 mm corner radius and a 7° clearance angle ensures reliable engagement and controlled chip formation, while the WNN10 coated carbide grade supports stable performance across a broad range of turning and boring tasks — order directly via Metav Werkzeuge or consult their specialists for application advice. WCGT040204-MN2 · WCGT040204-MN2 WNN10 · WNN10 – Indexable insert for boring and turning, Walter Tools The WCGT040204-MN2 WNN10 is an indexable trigon insert designed for precision boring and turning operations where consistent chip control and repeatable tool life are required Trigon 80° geometry for versatile engagement Coated carbide grade WNN10 for stable performance MN2 chipbreaker for controlled chip formation 7° clearance angle with 0.4 mm corner radius Consistent chip control for dependable cycle times The combination of the MN2 chipbreaker and the trigon geometry delivers controlled chip formation, reducing interruptions from problematic swarf and improving process stability. This insert’s geometry promotes predictable cutting forces during entering and cornering, which helps to maintain steady cycle times on serial turning or boring operations. The design is particularly advantageous where part repeatability and surface consistency are required, as the chip control contributes directly to fewer rejects and less machine downtime. Geometry and grade designed for repeatable edge life With a Trigon 80° form and a 0.4 mm corner radius, the insert offers a balance between strength at the cutting edge and accessibility in tight bore or profile work. The specified 7° clearance angle reduces rubbing while maintaining support for the cutting edge, which helps to extend usable tool life. The insert’s WNN10 coated carbide grade — a coated hardmetall composition — supports robust performance in general turning and light bore finishing; customers should consult the product matrix for exact workpiece-material recommendations. Practical integration into standard toolholders and production The insert’s designation and chipbreaker code allow straightforward selection of compatible toolholders and clamping systems, enabling quick set-up in machining centres and lathes. The standardised trigon form ensures repeatable indexing and straightforward spare-part management. For workshop planning, the insert simplifies inventory thanks to a common geometry that suits both external turning and certain internal boring applications, enhancing flexibility on the shop floor while keeping tool changeovers efficient. Contact Metav Werkzeuge for tailored advice on toolholder pairing, cutting data and order options for the Walter Tools WCGT040204-MN2 WNN10 indexable insert Technical Data Article number / SKU: WCGT040204-MN2-WNN10-WALTER Product type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Manufacturer: Walter Tools Designation: WCGT040204-MN2 WNN10 Facts Clearance angle: 7° Corner radius: 0.4 mm Insert form: Trigon 80° Size code: 04 Thickness code: 02 Tolerance class: G Special features Chipbreaker: MN2 Grade/series: WNN10; coated carbide Execution: T Series: Walter Schneidstoffsorte - Serie offen Base designation: WCGT040204-MN2 Material specification: Katalogabhängig ISO designation: WCGT040204-MN2 WNN10 FAQ What is the primary application for this insert? The insert is intended for boring and turning operations; the WCGT040204-MN2 WNN10 indexable insert by Walter Tools suits precision turning and certain internal bore finishing tasks where chip control is important. Which workpiece materials are suitable with this grade? The WNN10 coated carbide grade is a general-purpose hardmetall composition; suitability for specific materials should be verified against the product matrix and cutting data supplied for Walter Tools inserts. How does the MN2 chipbreaker influence performance? The MN2 chipbreaker promotes controlled chip formation and swarf evacuation, which helps to maintain process stability and reduce interruptions caused by long or tangled chips during turning and boring. Can this insert be used in standard trigon toolholders? Yes, the Trigon 80° form follows standard geometries and allows straightforward mounting in compatible toolholders designed for trigon inserts, enabling repeatable indexing and reliable clamping. What does the corner radius mean for surface finish? A 0.4 mm corner radius balances edge strength with achievable surface quality; this radius supports robust cutting on interrupted surfaces while aiding in producing consistent finishes in finishing passes. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation. There is no association between our company and the brands named. The offered item is an original, factory-new product of the respective manufacturer.
WCGT040204-X15 WAK15 Wendeplatten - Walter Tools
Take advantage of the insert's combination of a sharp, uncoated carbide grade and a Trigon 80° geometry to deliver clean results in aluminium and other non‑ferrous metals; this yields stable chip formation and reliable process performance. Order directly via Metav Werkzeuge or contact our consultants for machining recommendations and availability. Bohr-/Aufbohrwendeschneidplatte WCGT040204-X15 WAK15 — Uncoated carbide insert for aluminium drilling and boring | Walter Tools The WCGT040204-X15 WAK15 is an indexable drill/boring insert in Trigon 80° form, optimised for high‑feed machining of aluminium and other non‑ferrous metals. Uncoated carbide grade WAK15 for aluminium Trigon 80° form with 0.4 mm corner radius 7° relief angle for reduced cutting forces High‑efficiency machining of aluminium and non‑ferrous metals The insert is based on an uncoated carbide micro‑grain grade specifically formulated for non‑ferrous applications, delivering low adhesion and sharp cutting edges suited to aluminium and similar materials. The combination of material and geometry reduces built‑up edge and minimises rework, enabling higher feed rates and consistent surface finish. Engineers seeking to increase throughput will find the insert provides a measurable improvement in cycle time where chip evacuation and light cutting forces are essential. Geometry that stabilises chips and lowers cutting forces A Trigon 80° form combined with a 0.4 mm corner radius and a 7° relief angle produces a cutting geometry that balances edge strength with low contact area. The modest corner radius supports improved tool life on interrupted cuts, while the relief angle reduces friction at the flank face, lowering drive power and heat generation. In practice this means fewer tool changes and more predictable tool behaviour in series production, supporting machining strategies that demand both precision and repeatability. Practical integration and process reliability in production Equipped with the X15 chipbreaker and supplied as part of the Walter N‑grade system, the insert is designed for straightforward replacement in standard indexable drill bodies and boring heads. The tolerance class and standardised form permit reliable interchangeability, aiding quick set‑ups and consistent part quality. For specification checks, application optimisation or batch supply, Metav Werkzeuge provides technical consultation and stock information to support process planning and reduce downtime. Contact Metav Werkzeuge for tailored application advice and to secure delivery of Walter Tools WCGT040204-X15 WAK15 inserts for aluminium machining Technical Data Article number: WCGT040204-X15-WAK15-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WCGT040204-X15 WAK15 Walter Tools Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.4 mm Plate size code: 04 Plate thickness code: 02 Special features Grade: WAK15 (uncoated carbide) Chipbreaker: X15 Plate form: Trigon 80° Series: Walter N‑grade system Execution: T Tolerance class: G Application: aluminium and non‑ferrous metals FAQ Which materials is this insert intended for? The WCGT040204‑X15 WAK15 insert is intended primarily for aluminium and other non‑ferrous metals; the WAK15 grade is optimised to avoid material adhesion and to produce stable chips. Is the insert coated or uncoated? This indexable insert is uncoated carbide (WAK15), selected to preserve a very sharp cutting edge and to reduce the risk of built‑up edge when machining soft non‑ferrous materials. How does the Trigon 80° form influence drilling performance? The Trigon 80° form provides a positive cutting geometry that improves chip formation and allows higher feeds while maintaining the edge strength required for plunge and boring operations. What role does the X15 chipbreaker play? The X15 chipbreaker is designed to control chip shape and evacuation in aluminium alloys, improving surface quality and reducing the chance of chip entanglement during high‑feed machining. Can this insert be used in standard indexable drill bodies? Yes, the insert conforms to standard indexable dimensions and tolerance class G, enabling interchangeability in compatible drill and boring tool systems. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned solely for explanatory purposes. There is no connection between our company and the mentioned brands. The offered item is original, brand‑new goods from the manufacturer Walter Tools.
WCGT040204-X15 WTP35 WTP35 Wendeplatten - Walter Tools
Taking advantage of the combination of a coated carbide WTP35 grade, a Trigon 80° geometry and the X15 chipbreaker results in stable chip formation and consistent cutting performance; order the insert directly via Metav Werkzeuge or consult the specialists for compatibility and availability. WCGT040204-X15 WTP35 — Drilling/Boring indexable insert, Trigon 80°, Walter Tools A WCGT040204-X15 WTP35 indexable insert designed for drilling and boring operations, offering coated carbide performance with a Trigon 80° form for stable cutting in general machining tasks Coated carbide grade WTP35 for robust wear resistance Trigon 80° geometry for high cutting stability 0.4 mm corner radius for consistent edge strength X15 chipbreaker for reliable chip control Stable chip control for productive machining The coated carbide WTP35 formulation is optimised for reproducible cutting behaviour and predictable tool life. By combining a proven coating system with a dedicated chipbreaker, the insert promotes stable chip formation, which reduces the risk of irregular chips and helps maintain cycle times. This leads to fewer interruptions in the machining process and supports higher overall productivity in batch production. Geometry engineered for repeatable accuracy The Trigon 80° plate form and 7° relief angle deliver a balance between strength and accessibility in drilling and boring operations. The 0.4 mm corner radius assists in forming a robust cutting edge that tolerates intermittent loads while preserving workpiece surface quality. Together, these geometric choices minimise vibration and support repeatable dimensional results on series parts. Chip management and surface quality benefits With the X15 chipbreaker, the insert channels chips away from the cutting zone to prevent re-cutting and thermal accumulation. Controlled chip flow contributes directly to improved surface finish and reduces the likelihood of surface damage on delicate components. Where part tolerances are tight, the combined effect of chip control and edge stability helps to keep rework and inspection overhead to a minimum. Application guidance and material suitability This insert is supplied in a catalogue-dependent material specification and is classified within the Walter Tools series as a coated cemented carbide product. The precise workpiece compatibility depends on the detailed product matrix; therefore, material suitability should be checked against specific machining conditions. For unknown or mixed-material applications, consultation with Metav Werkzeuge or the Walter Tools technical literature is recommended to ensure optimal cutting parameters. Operational advantages for shopfloor efficiency The insert’s design focuses on consistent performance to reduce unplanned stops and tool changes. Predictable wear behaviour and reliable chip evacuation combine to extend effective tool life within specified process windows, supporting higher machine uptime. For manufacturing environments aiming for reproducible cycles and lower scrap rates, the insert’s features contribute to measurable operational improvements. For a tailored recommendation based on the Walter Tools WCGT040204-X15 WTP35 insert and to confirm suitability for specific materials or machine setups, contact Metav Werkzeuge for expert advice and fast availability. Technical data Article number: WCGT040204-X15-WTP35-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WCGT040204-X15 WTP35 Walter Tools Manufacturer: Walter Tools Product type: Bohr-/Aufbohrwendeschneidplatte Grade/Sort: WTP35 Series: Walter Schneidstoffsorte - Serie offen Core technical data Relief angle: 7° Corner radius: 0.4 mm Plate form: Trigon 80° Plate size: 04 Plate thickness: 02 Tolerance class: G Special features Chipbreaker: X15 Material: catalogue dependent (coated cemented carbide class) Designation: WCGT040204-X15 ISO designation: WCGT040204-X15 WTP35 Application note: Check product matrix for workpiece suitability FAQ What materials is the insert suitable for? The WCGT040204-X15 WTP35 insert is a coated cemented carbide grade; specific material suitability must be verified in the product matrix or with Metav Werkzeuge to match machining parameters and workpiece grades. How does the X15 chipbreaker affect performance? The X15 chipbreaker on the insert promotes controlled chip formation and evacuation, which helps to protect the cutting edge and improve surface finish during drilling and boring operations. What does the Trigon 80° form mean for stability? The Trigon 80° geometry increases cutting edge strength and tool stability under load, making the insert well suited to operations where robust performance and repeatability are required. Is the corner radius fixed and what does 0.4 mm provide? The 0.4 mm corner radius is specified to provide a compromise between edge strength and sharpness, supporting reliable edge life while maintaining good surface integrity on machined parts. Which designation should be referenced when ordering or checking compatibility? Reference the ISO designation WCGT040204-X15 WTP35 and the SKU WCGT040204-X15-WTP35-WALTER when checking compatibility or ordering. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany
WCGT040204-X15 WXM15 Wendeplatten - Walter Tools
Take advantage of the combination of precise geometry, a carbide grade optimised for non‑ferrous metals, and a compact plate profile for consistent hole quality; order the insert via Metav Werkzeuge or contact our consultants for application advice and matching tool recommendations. WCGT040204-X15 WXM15 — drill/reaming indexable insert, Trigon 80° geometry, 7° clearance — Walter Tools WCGT040204-X15 WXM15 is a compact drill and boring indexable insert designed for efficient machining of non‑ferrous metals in industrial production settings Trigon 80° insert geometry for stable seating Uncoated carbide grade WXM15 for non‑ferrous metals 7° clearance angle for reduced rubbing Corner radius 0.4 mm for predictable edge strength Consistent hole form and tool life through precise geometry The trigon 80° shape combined with a 7° clearance angle produces stable seating in toolholders and reduces the tendency to chatter during drilling and reaming operations. This geometry ensures repeatable hole form and position, which is particularly important in batch production where every sequence must fall within tight tolerances. The modest corner radius 0.4 mm balances edge strength and cutting aggressiveness, helping to maintain a predictable tool life while delivering consistent dimensional results. Optimised for machining non‑ferrous materials The insert is specified with the WXM15 grade — an uncoated carbide developed for NE‑materials. It is suited for machining aluminium, Kupfer and Messing where sharp cutting edges and low friction are required to avoid material build‑up on the cutting edge. The included chipbreaker X15 promotes favourable chip control for soft, ductile alloys, reducing the risk of choking and improving surface finish. Operators will notice fewer interruptions for manual cleaning and a smoother production flow. Practical selection and application guidance for industrial use As part of the Walter N‑Sortensystem, the insert fits systems where reliable part‑to‑part repeatability is demanded. The compact plate dimensions and the Trigon 80° form allow high packing density in multi‑insert drilling heads and indexable tools, saving spindle space and enabling higher productivity per tool assembly. For best results, match cutting parameters to the material group N (non‑ferrous) and monitor feed to exploit the sharp cutting geometry without overloading the edge. Contact Metav Werkzeuge for tailored cutting data, matching toolholders and to secure WCGT040204-X15 WXM15 inserts for immediate production use Technical data Article number: WCGT040204-X15-WXM15-WALTER Designation: WCGT040204-X15 WXM15 Brand: Walter Tools Facts Clearance angle: 7° Corner radius: 0.4 mm Insert form: Trigon 80° Plate size: 04 Plate thickness: 02 Tolerance class: G Special features Series: Walter N‑Sortensystem Grade: WXM15 (uncoated carbide) Chipbreaker: X15 Execution: T Material group: N – non‑ferrous metals (aluminium, Kupfer, Messing) FAQ What materials is this insert intended for? The WCGT040204-X15 WXM15 insert from Walter Tools is intended for non‑ferrous materials classified as N, including aluminium, Kupfer and Messing, where its sharp uncoated carbide grade performs best. Can the insert be used in small‑diameter multi‑insert drilling heads? Yes, the Trigon 80° profile and compact plate size 04 of the WCGT040204-X15 make it suitable for space‑constrained drilling heads and indexable tooling assemblies. How does the WXM15 grade affect surface finish? The WXM15 uncoated carbide grade combined with chipbreaker X15 promotes clean chip formation in ductile alloys, contributing to improved surface finish and fewer interruptions for edge cleaning when using the WCGT040204-X15 insert. Is the corner radius suitable for interrupted cuts? The 0.4 mm corner radius provides a compromise between edge strength and sharpness; the WCGT040204-X15 insert supports predictable performance in operations with mild interruptions typical of drilling and reaming non‑ferrous components. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered article is original factory‑new merchandise of the manufacturer Walter Tools.
WCGT040204-X25 WK1 WK1 Wendeplatten - Walter Tools
Take advantage of the blend of reliable cutting geometry and a grade engineered for broad material coverage — the Trigon 80° form with the WK1 uncoated cemented carbide base and the X25 chipbreaker deliver consistent chip control and predictable tool life; request selection support or order directly via Metav Werkzeuge. WCGT040204-X25 WK1 drill/boring indexable insert, Trigon 80° (Walter Tools) The WCGT040204-X25 WK1 is an indexable insert developed for drilling and boring tasks where consistent chip control and repeatable cutting performance are required in diverse production environments. Trigon 80° geometry for reliable cutting Uncoated cemented carbide grade WK1 X25 chipbreaker for stable chip control 7° clearance angle improves tool life 0.4 mm corner radius for fine finishing Higher productivity from a geometry designed for stability The Trigon 80° form combines a stable cutting edge with an open rake that supports reliable chip evacuation and consistent entry into holes or bores. With the X25 chipbreaker, the insert promotes orderly chip formation even under variable cutting conditions, reducing the risk of chip-related interruptions. The use of an uncoated cemented carbide grade (WK1) means the grade is well suited to general-purpose cutting where a balance of toughness and wear resistance is required; verify the specific substrate matrix in the catalogue for best results. By focusing on controlled chip flow and edge stability, this geometry helps maintain cycle times and reduces secondary operations, supporting a more economical machining process. Predictable accuracy and extended service intervals for production runs A 7° clearance angle and a 0.4 mm corner radius support low cutting forces and improved surface finish in typical drilling and boring applications. The insert’s tolerance classification G and its coded dimensions (plate size 04, thickness code 02) ensure repeatable seating and concentricity in compatible toolholders, which is essential for batch production. When configured correctly in a suitable holder, the insert gives consistent hole quality and repeatable tool offsets, simplifying toolpath programming and inspection routines. These attributes translate into fewer tool changes and steadier part quality over longer production cycles. Practical integration and application advice for workshop use Selection of the correct grade and geometry is decisive: while WK1 is an uncoated carbide grade intended for broad application, the final choice depends on the workpiece material and cycle demands — consult the product matrix for exact suitability. For workshops integrating these inserts into existing tool systems, the clear size and form codes facilitate quick matching with standard holders and clamping systems. For additional technical data or assistance in specifying the correct insert for a particular material or machine setup, Metav Werkzeuge provides direct consultation. Contact details are available for rapid clarification of catalogue-dependent material options and application recommendations. Contact Metav Werkzeuge for tailored selection of Walter Tools WCGT040204-X25 WK1 inserts and request a technical consultation to match the grade to the intended application or production requirement Technical Data Article number: WCGT040204-X25-WK1-WALTER Designation: WCGT040204-X25 WK1 Product type: Bohr-/Aufbohrwendeschneidplatte (drill/boring indexable insert) Brand: Walter Tools Facts Geometry: Trigon 80° Clearance angle: 7° Corner radius: 0.4 mm Chipbreaker: X25 Plate size code: 04 Thickness code: 02 Tolerance class: G Execution: T Special features Grade: WK1 (uncoated cemented carbide) Series: Walter Schneidstoffsorte - Serie offen Material designation: catalogue-dependent ISO designation: WCGT040204-X25 WK1 Label: Bohr-/Aufbohrwendeschneidplatte WCGT040204-X25 WK1 Walter Tools FAQ What materials is this insert suitable for? The WCGT040204-X25 WK1 insert is provided in the WK1 uncoated cemented carbide grade; suitability for specific workpiece materials should be checked against the product matrix in the catalogue. How does the X25 chipbreaker affect drilling performance? The X25 chipbreaker promotes controlled chip formation and evacuation, improving machining stability during drilling and boring and reducing downtime caused by poor chip behaviour. What does the Trigon 80° geometry mean for hole quality? Trigon 80° geometry provides a stable cutting form and consistent entry into the workpiece, which helps maintain concentricity and surface finish in bore production. How to interpret the size and thickness codes on the insert? Codes such as plate size 04 and thickness 02 identify the insert dimensions and seating profile; these codes match standard holder specifications for correct mounting and repeatable positioning. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only and do not indicate any affiliation between our company and the named manufacturers. The offered item is original, brand-new goods from the manufacturer Walter Tools.
WCGT040204-X5 WAK15 Wendeplatten - Walter Tools
Reliable chip control and material compatibility make this insert ideal for efficient aluminium and non‑ferrous machining; its Trigon geometry and uncoated carbide grade reduce adhesion and improve stability. Order the WCGT040204-X5 WAK15 directly via Metav Werkzeuge or ask our consultants if needed. WCGT040204-X5 WAK15 — Indexable drilling/reaming insert for aluminium (Walter Tools) WCGT040204-X5 WAK15 is a trigon‑form indexable insert designed for drilling and reaming operations in aluminium and other non‑ferrous metals, supplied within the Walter N‑Series. Uncoated carbide grade for non‑ferrous metals Trigon 80° form for high axial stability X5 chipbreaker for reliable chip control 7° clearance and 0.4 mm corner radius Consistent machining performance for aluminium work The WAK15 uncoated carbide grade is optimised for aluminium and other non‑ferrous materials, delivering sharp cutting edges and low adhesion during high‑feed operations. The combination of a Trigon 80° insert form and the X5 chipbreaker reduces build‑up on the cutting edge and promotes consistent chip flow, which directly improves surface quality and reduces downtime for cleaning. These traits make the insert particularly suitable for cyclic drilling and reaming where repeatable outcomes and short cycle times are required. Geometry that extends edge life and process reliability A 7° clearance angle and a 0.4 mm corner radius balance edge strength with low cutting forces, lowering the risk of material welding and premature edge wear. The trigon profile provides a larger contact area for axial loads, improving tool stability during plunge operations. For machinists unfamiliar with technical terms: the clearance angle keeps the insert from rubbing on the workpiece, while the corner radius helps distribute cutting stresses to avoid chipping. Together, these geometric choices translate into longer tool life and fewer tool changes per shift. Easy integration into standard indexable drilling systems The insert is produced to the Walter N‑Series specifications and is identified as WCGT040204-X5 WAK15, making it straightforward to match with compatible toolholders designed for trigon 80° inserts. The size and thickness codes follow industry conventions, enabling quick selection in tool lists and CAM routines. Integration is simple: the insert’s chipbreaker and uncoated surface reduce the need for aggressive coolant strategies in many aluminium applications, supporting efficient retrofit into existing machining cells without process upheaval. Production benefits from a reputable cutting tool partner Choosing a Walter Tools insert combines robust tool geometry with the manufacturer’s focus on process stability and surface quality. The uncoated carbide construction delivers predictable wear behaviour in soft, sticky materials like aluminium, while the X5 chipbreaker assists with continuous chip evacuation. For production managers, this means fewer interruptions, improved first‑pass yield and more consistent part tolerances across batches — an economic benefit that supports throughput and quality goals. Contact Metav Werkzeuge for availability and application guidance on the WAK15 grade — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific aluminium machining tasks Technical Data SKU: WCGT040204-X5-WAK15-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WCGT040204-X5 WAK15 Walter Tools Series: Walter N‑Sortensystem Grade: WAK15 Material: uncoated carbide Core specifications Insert form: Trigon 80° Clearance angle: 7° Corner radius: 0.4 mm Insert size: 04 Thickness: 02 Chipbreaker: X5 Applications and features Suitable for aluminium and non‑ferrous metals For drilling and reaming indexable systems Walter N‑Series compatibility Uncoated grade for low adhesion Stable chip control with X5 chipbreaker Trigon geometry for axial stability FAQ What materials is the insert optimised for? The WCGT040204-X5 WAK15 is optimised for aluminium and other non‑ferrous metals, using the WAK15 uncoated carbide grade to reduce adhesion and improve surface finish. How does the X5 chipbreaker affect production? The X5 chipbreaker on this insert promotes short, controllable chips and reliable evacuation, which reduces stoppages and supports consistent cycle times in aluminium drilling applications. Which toolholders are compatible with the insert form? Trigon 80° toolholders designed for the Walter N‑Series accept this insert form; the geometry and coding match standard indexable drilling/reaming tool systems. Is this insert coated or uncoated, and why does that matter? This insert is uncoated carbide (WAK15). For aluminium and sticky non‑ferrous materials, uncoated grades minimise built‑up edge and improve cutting behaviour compared with many coated grades. Can the insert be used for heavy interrupted cuts? The trigon geometry and 0.4 mm corner radius increase edge robustness, so moderate interruptions are manageable; for severe interruptions, select a grade and radius matched to the application. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Walter AG (brand appearance: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names are used solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered item is original, factory‑new merchandise of the manufacturer.
WCGT040204-X5 WTP35 Wendeplatten - Walter Tools
Benefit from the combination of WTP35 coated carbide and the X5 chipbreaker for predictable chip control and improved tool life; order the insert directly via Metav Werkzeuge or contact our consultants for application advice. WCGT040204-X5 WTP35 — Trigon 80° drilling/boring indexable insert, X5 chipbreaker | Walter Tools WCGT040204-X5 WTP35 is a compact drilling/boring indexable insert engineered for stable chip formation and versatile machining across a wide range of workpiece materials in industrial drilling and boring operations Trigon 80° geometry for secure clamping X5 chipbreaker for stable chip control 0.4 mm corner radius for edge strength 7° clearance angle for reduced rubbing Predictable chips and extended cutting life for productive machining The insert is supplied in the WTP35 grade, a coated carbide designed for general industrial use; the combination of the grade and the X5 chipbreaker promotes stable chip formation and consistent cutting performance. In practice, this means fewer interruptions from poor chip evacuation and a more predictable tool life, which supports higher machine uptime and improved process reliability. The documented cutting-grade concept helps form a verifiable basis for tool selection in production environments. Geometry tailored to accuracy in drilling and boring The Trigon 80° plate form and a 0.4 mm corner radius increase edge robustness while maintaining cutting precision; the 7° clearance angle reduces flank rubbing and heat build-up during entry, improving surface finish in through-holes and bores. These geometric details translate into measurable benefits: improved hole roundness, reduced burr formation and more repeatable tolerances in serial production. The compact plate size and standard thickness codes suit tight toolholders and allow straightforward integration into common drilling and boring tool systems. Practical benefits for workshop integration and cost-efficiency As an indexable insert, the component minimises downtime through fast indexing and replacement, while the tolerance class G and open series designation simplify selection across mounting systems. The plate’s execution code and catalogue-dependent substrate information give process engineers a clear technical basis for validation within existing tool matrices. This approach supports rational decision-making: choosing a replaceable insert that balances process stability and economy of operation reduces overall cycle costs and simplifies inventory management. Discuss application needs with Metav Werkzeuge to confirm suitability and specify the correct insert geometry for the intended operation — contact our technical team at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: WCGT040204-X5-WTP35-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WCGT040204-X5 WTP35 Walter Tools Manufacturer: Walter Tools Product type: Bohr-/Aufbohrwendeschneidplatte ISO designation: WCGT040204-X5 WTP35 Series: Walter Schneidstoffsorte - Serie offen Tolerance class: G Facts Corner radius: 0.4 mm Clearance angle: 7° Plate form: Trigon 80° Plate size: 04 Plate thickness: 02 Special features Chipbreaker: X5 Grade: WTP35 (coated carbide) Execution: T Material: Katalogabhängig Designation without grade: WCGT040204-X5 FAQ What materials is this insert suitable for? The WCGT040204-X5 WTP35 insert is specified with catalogue-dependent substrate information; its WTP35 coated carbide grade is intended for a broad material range—verify the exact workpiece suitability against the product matrix before serial use. How does the X5 chipbreaker affect drilling performance? The X5 chipbreaker promotes controlled chip formation during drilling and boring, reducing clogging and enabling longer uninterrupted cutting periods with consistent hole quality. Can this insert be used in standard drilling holders? The Trigon 80° format and the published thickness/size codes are compatible with common toolholder systems designed for Trigon-style indexable inserts; confirm holder compatibility with the ISO designation WCGT040204-X5 WTP35. What does tolerance class G mean for production? Tolerance class G indicates the manufacturing tolerance and repeatability of the insert geometry, which supports predictable positioning and consistent machining results in series production. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are used for explanation only. There is no affiliation between our company and the mentioned brands. The offered item is an original, factory-new product of the manufacturer (Walter Tools).
WCGT040204-X5 WXM15 Wendeplatten - Walter Tools
Take advantage of the combination of precise WXM15 carbide grade and a Trigon 80° geometry with X5 chipbreaker for efficient drilling and boring of non‑ferrous metals; the result is reliable chip control and stable cutting action. Order directly via Metav Werkzeuge or consult our specialists for tailored application advice. WCGT040204-X5 WXM15 drilling/boring indexable insert — Trigon 80° with X5 chipbreaker by Walter Tools WCGT040204-X5 WXM15 is a Trigon 80° indexable insert designed for drilling and boring tasks in non‑ferrous metals, offering a sharp uncoated carbide grade and an X5 chipbreaker for controlled chip formation Trigon 80° geometry for improved accessibility X5 chipbreaker for consistent chip control Grade WXM15 uncoated carbide for NE‑metals 7° clearance angle reduces rubbing at the flank 0.4 mm nose radius for balanced edge strength Efficient machining of non‑ferrous metals with a purpose The insert is engineered for productive work on non‑ferrous metals such as aluminium, copper and brass. The WXM15 grade denotes an uncoated cemented carbide tailored to provide a very sharp cutting edge and low tendency for built‑up edge when machining soft, adhesive materials. As a result, the geometry and material pairing reduce rework and contribute to steady cycle times in series drilling and boring, which supports a cost‑efficient production flow and predictable outcomes. Geometry that balances cutting performance and edge security The Trigon 80° form combines a favourable approach angle with an accessible insert footprint, permitting secure clamping while enabling the tool to enter tight bores. The 0.4 mm corner radius provides a compromise between edge strength and finishing capability: it is robust enough to withstand vibrations yet fine enough to maintain surface quality. The 7° clearance minimises flank contact and friction, helping to preserve the cutting edge and reduce heat transfer into the workpiece during sustained operations. Chip control and process stability for drilling and boring tasks The integrated X5 chipbreaker is designed to manage chips typical of NE‑materials, breaking or guiding swarf reliably to avoid long stringy chips that can foul the tool or work area. Combined with the insert’s uncoated carbide composition, this feature supports consistent cut behaviour and lowers the frequency of manual chip clearing. As part of the Walter N‑series, the insert fits into established routines for non‑ferrous machining and permits quick grade selection for specific applications, increasing process security and repeatability. Practical application guidance and handling notes The insert suits drilling and boring operations where adhesion and soft material behaviour present a challenge. It performs best with appropriate feed and speed settings for aluminium and similar alloys and benefits from through‑tool or directed coolant strategies where applicable. As an uncoated grade, WXM15 should be matched to cutting parameters that exploit its sharp edge; this reduces built‑up edge and optimises surface finish. For integration into existing toolholders, check compatibility with the WCGT04 insert seat and clamping specifications. Choose the Walter Tools WXM15 Trigon insert for reliable, process‑secure non‑ferrous drilling and contact Metav Werkzeuge for availability and tailored machining advice via info@metav-werkzeuge.com or by calling +49 2822 7131930 Technical data Article number: WCGT040204-X5-WXM15-WALTER Designation: WCGT040204-X5 WXM15 Type: drilling/boring indexable insert Series: Walter N‑Sortensystem Grade: WXM15 Manufacturer: Walter Tools Key figures Clearance angle: 7° Corner radius: 0.4 mm Insert size code: 04 Thickness code: 02 Tolerance class: G Materials & features Uncoated cemented carbide (WXM15) Application: Non‑ferrous metals (aluminium, copper, brass) Chipbreaker: X5 Insert form: Trigon 80° Series designation: Walter N‑Sortensystem FAQ Which materials are suitable for this insert? The WCGT040204-X5 WXM15 insert is intended for non‑ferrous metals, specifically aluminium, copper and brass, as indicated by the WXM15 grade and the Walter N‑series design. Is the insert coated or uncoated? The cutting grade WXM15 for this insert is an uncoated cemented carbide, chosen to provide a sharp cutting edge and to reduce material adhesion in NE‑materials. How does the X5 chipbreaker help in drilling operations? The X5 chipbreaker controls and breaks chips typical of soft, adhesive alloys, reducing the risk of long, stringy swarf that can interfere with drilling and boring cycles using this Walter Tools insert. What is the significance of the Trigon 80° form? The Trigon 80° geometry offers a balance of edge exposure and insert stability, improving accessibility in bore entries while maintaining a secure clamping interface for reliable machining. Can this insert be used for finishing passes? With a 0.4 mm corner radius, the insert provides a compromise between robustness and surface finish; it can be used for light finishing where edge strength and dimensional control are required. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is an original, factory‑new product of the manufacturer Walter Tools.
WCGT050304-X15 WAK15 Wendeplatten - Walter Tools
Take advantage of the sharp geometry and aluminium‑optimised grade for efficient non‑ferrous machining; the combination of a Trigon 80° form, 7° clearance and a 0.4 mm corner radius provides consistent surface quality and secure tool life management. Order the insert directly via Metav Werkzeuge or consult our advisors for application-specific recommendations. WCGT050304-X15 WAK15 – Drilling / boring indexable insert, Trigon 80°, Walter Tools A WCGT050304-X15 WAK15 indexable insert engineered for high‑performance machining of aluminium and other non‑ferrous materials, suited to productive holemaking and finishing operations. Uncoated carbide grade WAK15 for aluminium Trigon 80° insert geometry 7° clearance angle for positive cutting 0.4 mm corner radius for smooth finish Higher throughput for non‑ferrous production The insert is based on the WAK15 uncoated carbide grade from the Walter N‑Sortensystem, optimised specifically for aluminium and other non‑ferrous metals. This material choice favours a very sharp cutting edge and a low tendency for material adhesion, which reduces the risk of built‑up edge and helps maintain consistent cycle times. In practice, these characteristics translate to fewer reworks and a more reliable production output when machining soft, ductile alloys. Geometry that improves surface quality and process stability A Trigon 80° shape combined with a 7° clearance produces a positive cutting geometry that requires less cutting force than blunt configurations. The 0.4 mm corner radius balances edge strength with the need for a fine surface finish, making the insert suitable for both roughing and light finishing passes. For operators new to insert geometry, the positive rake and defined corner radius mean a predictable chip formation and a lower tendency for vibration in common drilling and boring setups. Chip control and suitability for demanding operations The integrated chipbreaker designation X15 is designed to assist chip formation in non‑ferrous cutting, promoting short, controllable chips rather than long stringy swarf. This reduces the need for additional chip management measures at the tool and supports safer, more efficient machining cycles. The insert form and chip control features make it a practical choice for automated and serial production where consistent chip evacuation is essential. Easy integration and material compatibility Produced to a standard tolerance class G and supplied in the Trigon 80° plate form, this indexable insert fits established toolholders designed for the WCGT family and similar geometries. It is intended for aluminium and other N‑group materials according to ISO categorisation; it is not specified for stainless steel applications. The simple, uncoated carbide composition eases the selection process for applications where coatings would otherwise promote adhesion or alter cutting temperatures. For machining aluminium with the proven Walter Tools WAK15 grade, contact Metav Werkzeuge for tailored advice and order support: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number / SKU: WCGT050304-X15-WAK15-WALTER Internal designation: WCGT050304-X15 WAK15 Product type: Bohr-/Aufbohrwendeschneidplatte (indexable insert) Brand: Walter Tools Series: Walter N‑Sortensystem Grade: WAK15 Facts Clearance angle: 7° Corner radius: 0.4 mm Insert size: 05 Plate thickness: 03 Tolerance class: G Special features Uncoated carbide (WAK15) Trigon 80° plate form Chipbreaker: X15 Application group: non‑ferrous metals (aluminium, copper, brass) Execution: T FAQ Which materials is this insert intended for? The WCGT050304‑X15 WAK15 insert is optimised for aluminium and other non‑ferrous materials (ISO group N), making it suitable for machining copper and brass alloys where a sharp edge and low adhesion are required. Is the insert coated or uncoated? This insert uses an uncoated carbide grade (WAK15), selected to reduce built‑up material and preserve edge sharpness during non‑ferrous cutting operations. Can this insert be used on stainless steel or hardened materials? The WAK15 grade and the specified geometry are not intended for stainless steel or hardened applications; the insert is designated for non‑ferrous work and does not list rostfreier Stahl compatibility. How does the Trigon 80° form affect clamping and tool life? The Trigon 80° shape offers three usable cutting edges per indexable insert and provides a compact seating geometry that supports stable clamping and consistent edge repeatability, which helps maintain predictable tool life under recommended operating conditions. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and product names remain the property of their respective owners. Brand names are used for explanatory purposes only. The offered article is an original, factory‑new product of the manufacturer. There is no affiliation or partnership between our company and the trademark owners.
WCGT050304-X15 WTP35 T Wendeplatten - Walter Tools
Take advantage of the combination of consistent edge stability, coated carbide performance and the Trigon 80° geometry for reliable boring operations; order directly via Metav Werkzeuge or contact our consultants for specification support. WCGT050304-X15 WTP35 boring/reaming indexable insert — Trigon 80° with chipbreaker X15 — Walter Tools A WCGT050304-X15 WTP35 is an indexable insert designed for precision boring and reworking of bores, offering a compact Trigon 80° form with a dedicated chip control geometry for stable material removal. Coated carbide grade WTP35 Trigon 80° geometry for stability Integrated chipbreaker X15 7° free angle for secure cutting Consistent process performance through material and geometry The coated carbide WTP35 grade delivers a balanced combination of wear resistance and reliable edge integrity, enabling steady material removal in demanding production routines. The Trigon 80° plate form provides a robust cutting face and reduced vibration, while the chipbreaker X15 manages swarf to maintain process security. Combined, these characteristics support predictable tool life and repeatable results in serial boring tasks. Precise cutting action for tight tolerances With a 7° free angle and a corner radius of 0.4, the insert is configured to produce controlled engagement and stable feed response, which helps to preserve dimensional accuracy during bore enlargement. The modest plate thickness and compact size contribute to secure clamping and reduced runout risk, translating into improved surface finish and fewer rework cycles when machining internal diameters. Versatile application and straightforward inventory integration The insert’s catalogue-dependent substrate and coating selection enable adaptation to a broad material matrix; consult the product matrix to confirm suitability for specific workpiece materials. The standardised designation and compact footprint make the insert straightforward to catalogue and replace in modular boring heads, reducing downtime and simplifying tool management for production teams. Practical benefits for shop-floor efficiency Engineered for repetitive operations, the insert’s geometry and coated hardmetal composition prioritise stable chip formation and consistent cutting behaviour. This leads to reduced variance between tool changes, fewer unexpected interruptions and a more streamlined manufacturing flow. The overall design supports productive machining especially where reproducibility and low-maintenance tooling are priorities. Contact Metav Werkzeuge for tailored recommendations on tooling integration and to discuss suitability of this Walter Tools insert for specific materials and bore sizes — Metav Werkzeuge can advise on tooling systems, cutting data and availability via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: WCGT050304-X15-WTP35-WALTER Product type: Bohr-/Aufbohrwendeschneidplatte Manufacturer: Walter Tools Designation: WCGT050304-X15 WTP35 Series: Walter Schneidstoffsorte - Serie offen Facts Free angle: 7° Corner radius: 0.4 Thickness: 03 Plate size: 05 Tolerance class: G Special features Coating: Katalogabhängig Material: Katalogabhängig Plate form: Trigon 80° Chipbreaker: X15 Grade: WTP35 Execution: T FAQ What materials is this insert suitable for? The WCGT050304-X15 WTP35 is based on a coated carbide grade; suitability depends on the product matrix and coating variant, so check the catalogue-specific matrix for precise material recommendations. How does the Trigon 80° form affect boring performance? The Trigon 80° geometry offers a stable cutting face and improved resistance to deflection, which benefits bore accuracy and repeatability during reaming and enlargement tasks. What is the role of the chipbreaker X15? Chipbreaker X15 is designed to control swarf formation and evacuation, supporting uninterrupted cutting and reducing the likelihood of chip-related surface damage. Can the insert be used in existing boring heads? The compact designation and standardised form factor allow integration into common modular boring systems; confirm clamping compatibility with the host toolholder. How should cutting data be determined for this grade? Cutting data should be selected based on the chosen coating/substrate option and the workpiece material as defined in the manufacturer’s product matrix to achieve optimal tool life. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. There is no connection between our company and the mentioned brands. The offered item is original, factory-new merchandise of the manufacturer. The Walter brand is mentioned where relevant for clarification of product origin and specification.
WCGT050304-X15 WXM15 Wendeplatten - Walter Tools
A compact, application‑focused insert that pairs uncoated carbide sharpness with the X15 chipbreaker for reliable machining of non‑ferrous metals; ideal where reduced material adhesion and consistent chip control are required. Order the insert directly via Metav Werkzeuge or consult our specialists for precise tool selection. WCGT050304-X15 WXM15 Drilling/Boring indexable insert – Trigon 80° geometry, for non‑ferrous metals, Walter Tools The WCGT050304-X15 WXM15 is a trigon indexable insert engineered for drilling and boring operations in non‑ferrous materials, combining a sharp uncoated cutting edge with targeted chip control. Trigon 80° geometry for stable positioning Uncoated carbide grade WXM15 for NE metals X15 chipbreaker reduces material build‑up 7° clearance angle with 0.4 mm corner radius Improved cycle times through material‑specific grade selection Choosing an insert with the WXM15 grade brings measurable process benefits for non‑ferrous machining. The uncoated carbide composition provides a very sharp edge that minimises friction and reduces the risk of material sticking—especially with aluminium and brass‑type alloys—leading to more consistent feeds and fewer interruptions. In practice, this means more predictable cycle times and reduced scrap rates, because the cutting geometry and grade are matched to the softer, more adhesive behaviour of NE materials. Consistent surface finish and chip control from geometry and breaker The Trigon 80° format, paired with the X15 chipbreaker, stabilises chip formation during drilling and reaming tasks. A modest 7° relief angle and 0.4 mm corner radius help to distribute cutting forces and lower vibration, which improves hole quality and tool life. For operators unfamiliar with chipbreaker nomenclature: the X15 profile is shaped to fragment and evacuate swarf effectively from the bore, preventing ropey chips and reducing the chance of material re‑deposit on the cutting edge. Easy integration into existing tooling systems with clear specifications This insert is supplied in the Walter N‑series family and complies with tolerance class G, making it straightforward to match with standard indexable toolholders for drilling/boring applications. The compact format (size 05, thickness 03) is intended for machines where accurate positioning and repeatability are essential. For machining shops, the combination of geometry and material leads to low‑maintenance performance: fewer edge dressings, predictable regrinds and straightforward inventory management when paired with Walter tooling platforms. For technical advice tailored to a specific component or to confirm suitability of Walter Tools inserts for a given non‑ferrous application, contact Metav Werkzeuge for rapid, practice‑oriented support and supply coordination Technical data Article number: WCGT050304-X15-WXM15-WALTER Label: Bohr-/Aufbohrwendeschneidplatte WCGT050304-X15 WXM15 Walter Tools SKU: WCGT050304-X15-WXM15-WALTER Facts Relief angle: 7° Corner radius: 0.4 mm Plate form: Trigon 80° Size: 05 Thickness: 03 Tolerance class: G Special features Grade: WXM15 (uncoated carbide) Chipbreaker: X15 Series: Walter N‑sortensystem Application: non‑ferrous metals (NE) Product type: Drilling/Boring indexable insert FAQ What materials is this insert suitable for? The WCGT050304-X15 WXM15 insert is designed primarily for non‑ferrous metals, including aluminium, copper and brass alloys; the WXM15 grade optimises cutting behaviour for these groups. How does the X15 chipbreaker benefit drilling operations? The X15 chipbreaker promotes short, controllable chips and lowers adhesion risk in bores, improving evacuation and helping to maintain a clean cutting edge during drilling and boring. What does the Trigon 80° shape mean for tool setup? A Trigon 80° plate provides stable seating in indexable holders and supports radial loading, which is beneficial for axial drilling and small‑diameter boring where positional accuracy matters. Can this insert be used with standard Walter toolholders? Yes, the insert is part of the Walter N‑series and is intended for integration with compatible Walter toolholders that accept size 05, thickness 03 trigon plates. Is the cutting material coated? No; the WXM15 grade is supplied as uncoated carbide, selected to provide the sharpness and low adhesion needed for NE materials. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Walter AG (brand appearance: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and product names remain the property of their respective owners. The described item is an original, factory‑new product of the manufacturer.
WCGT050304-X25 WK1 T Wendeplatten - Walter Tools
Benefit from the combination of WK1 uncoated carbide and Trigon 80° geometry for stable chip formation and efficient holemaking; the chipbreaker X25 supports controlled chips and consistent productivity. Order the insert directly via Metav Werkzeuge or consult their advisors for selection support. WCGT050304-X25 WK1 – Drill/reaming indexable insert, Trigon 80°, Chipbreaker X25 (Walter Tools) The WCGT050304-X25 WK1 is a drill/reaming indexable insert designed for precision holemaking and bore finishing in demanding turning and drilling operations. Trigon 80° geometry for reliable entry Uncoated carbide grade WK1 for broad applicability Chipbreaker X25 for repeatable chip control Maximise machinability with geometry and grade The combination of the Trigon 80° form and the WK1 uncoated carbide grade delivers a balance of toughness and wear resistance that suits a wide range of holemaking tasks. With a 7° clearance angle and a corner radius 0.4 mm, the insert reduces cutting forces and supports dimensional stability during plunge and rotary operations. The chipbreaker X25 is designed for controlled chip formation, lowering the risk of entanglement and reducing cycle interruptions; this rational setup leads to higher throughput and predictable tool change intervals. Easier process set-up and reduced downtime Clear specifications and a consistent cutting geometry simplify process planning. The insert’s features contribute directly to shorter set-up times and improved repeatability, supporting higher net productivity. For unfamiliar material mixes, the manufacturer’s product matrix should be consulted to confirm suitability; this step ensures the selected grade performs as expected under the given cutting speeds and feeds. Combined with the stable edge condition of an uncoated carbide substrate, users benefit from longer effective tool life and fewer unforeseen stoppages. Confidence through proven manufacturing standards Tolerance class G and the open-series designation indicate a standardised production profile suitable for industrial use. The construction and finish of the insert support accurate indexing and secure clamping in modern toolholders, which in turn preserves hole quality over repeated tool changes. For applications where material compatibility is critical, reference the product matrix — the insert was developed for versatile use but final selection depends on the specific workpiece material and machining parameters. The association with Walter Tools underscores a focus on consistent results and process reliability. For reliable, process-secure drilling and reaming with Walter Tools inserts, contact Metav Werkzeuge for tailored application advice and fast supply: info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: WCGT050304-X25-WK1-WALTER ISO designation: WCGT050304-X25 WK1 Article designation: WCGT050304-X25 Product type: Drill/reaming indexable insert Brand: Walter Tools Grade: WK1 Facts Clearance angle: 7° Corner radius: 0.4 mm Insert shape: Trigon 80° Insert size: 05 Thickness code: 03 Tolerance class: G Chipbreaker: X25 Special features Substrate: uncoated cemented carbide Series: Walter Schneidstoffsorte - Serie offen Execution: T Material: catalogue-dependent Application note: Check product matrix for material suitability FAQ What materials is this insert suitable for? Material suitability should be verified against the manufacturer’s product matrix; the WCGT050304-X25 WK1 is an uncoated carbide grade intended for broad applicability but final selection depends on the specific workpiece material. How does the chipbreaker X25 affect machining? The chipbreaker X25 promotes controlled chip formation, which helps reduce entanglement, supports safer automatic machining and contributes to steady cycle times with fewer interruptions. What does the Trigon 80° shape offer for drilling? The Trigon 80° geometry provides robust cutting edges for entry and stability in bore operations, improving centring and reducing lateral forces during plunge cuts. Is the insert suitable for finishing as well as roughing? With its 0.4 mm corner radius and 7° clearance angle, the insert can contribute to consistent surface quality; however, final suitability for finishing depends on cutting parameters and material—refer to the product matrix. What does the WK1 grade mean in practice? The WK1 designation denotes an uncoated cemented carbide grade from Walter Tools geared towards a balance of toughness and wear resistance; performance should be validated with the specific machining conditions. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is among the world’s leading manufacturers of precision cutting tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names are the property of their respective owners; they are mentioned here for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is original, brand‑new merchandise from the manufacturer.
WCGT050304-X5 WAK15 Wendeplatten - Walter Tools
Combining the sharp WAK15 cemented carbide grade with the Trigon 80° geometry and the X5 chipbreaker delivers efficient, low-adhesion machining of aluminium and other non‑ferrous metals while maintaining consistent surface quality; order directly via Metav Werkzeuge or contact our application consultants for tailored recommendations. WCGT050304-X5 WAK15 — Trigon 80° drilling and bore‑enlargement indexable insert by Walter Tools The WCGT050304-X5 WAK15 is a Trigon 80° indexable insert designed for drilling and bore enlargement in aluminium and non‑ferrous metals, offering a sharp edge geometry and controlled chip formation for reliable production runs Trigon 80° shape for stable cutting Uncoated WAK15 cemented carbide grade 0.4 mm nose radius for fine finish X5 chipbreaker for controlled chips Efficient machining of aluminium and non‑ferrous metals The uncoated WAK15 cemented carbide grade is formulated specifically for the challenges of the ISO N group, which includes aluminium and other non‑ferrous alloys. The combination of a sharp cutting edge and a low‑adhesion substrate reduces the risk of built‑up edge and sticking that commonly impair productivity when machining soft metals. This results in higher material removal rates and fewer interruptions for cleaning or rework, improving cycle times in series production. The insert’s design supports stable cutting even where feed and speed need to be adapted for thin‑walled components, delivering a measurable increase in process efficiency. Geometry tuned for consistent surface quality and chip control The Trigon 80° form, paired with a 0.4 mm nose radius and 7° relief, delivers a balance between rigidity and edge strength that is well suited to drilling and reaming operations. The chipbreaker X5 is engineered to fragment swarf reliably when working with sticky or ductile alloys, preventing long, stringy chips that can foul the tool or workpiece. In practice, this means fewer surface defects and a reduced need for secondary finishing. The terms "relief" and "nose radius" refer respectively to the clearance angle behind the cutting edge and the rounded tip that determines corner strength and surface finish; both are key parameters in achieving repeatable quality. System compatibility and economical operation Part of the Walter N‑series, this insert is available in the common designation WCGT050304‑X5 and fits industry‑standard holders for Trigon inserts. The plate size code 05 and thickness 03 correspond to compact toolholder options that help reduce runout and increase rigidity in smaller diameters. Tolerance class G and execution T ensure consistent interchangeability and predictable tool life, which simplifies inventory management. The ability to rotate to fresh cutting edges and the use of a cost‑efficient uncoated carbide grade contribute to a lower cost per edge in high‑volume machining, making the insert a practical choice for shops seeking dependable performance without unnecessary complexity. For application-specific advice on Walter Tools WAK15 inserts and to arrange supply through Metav Werkzeuge, email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: WCGT050304-X5-WAK15-WALTER ISO designation: WCGT050304-X5 WAK15 Series: Walter N‑Sortensystem Grade: WAK15 Core figures Free angle: 7° Nose radius: 0.4 mm Plate form: Trigon 80° Plate size: 05 Plate thickness: 03 Tolerance class: G Special features Uncoated cemented carbide for non‑ferrous applications Chipbreaker X5 for controlled chips Optimised for aluminium and other ISO N materials Execution: T Walter N‑series compatibility FAQ What materials is this insert suitable for? The WCGT050304‑X5 WAK15 insert is designed primarily for aluminium and other non‑ferrous metals (ISO N), utilising the WAK15 uncoated carbide grade to reduce material adhesion. How does the X5 chipbreaker affect performance? The chipbreaker X5 promotes consistent chip segmentation during drilling and bore enlargement with ductile materials, improving swarf disposal and reducing the risk of surface damage. Can this insert be reground or reconditioned? This indexable insert is intended for multi‑edge use by indexing; reconditioning depends on shop practices and should consider the small 0.4 mm nose radius and edge geometry to preserve intended performance. Which toolholders accept the WCGT050304‑X5 designation? The WCGT050304‑X5 conforms to the Trigon 80° insert family standards and fits holders designed for Trigon inserts of plate size 05 and thickness 03 in the Walter N‑series system. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand: Walter Tools) is a leading manufacturer of precision cutting tools and is part of the Sandvik group. Protected trademarks and trade names are the property of their respective owners; brand names and protected trade designations are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands beyond the sale of original, factory‑new products from the manufacturer.
WCGT050304-X5 WK1 Wendeplatten - Walter Tools
Take advantage of the combination of stable chip control and robust Trigon geometry for reliable holemaking; order directly via Metav Werkzeuge or consult their specialists for application matching. WCGT050304-X5 WK1 – Drill/boring indexable insert by Walter Tools, Trigon 80° with X5 chipbreaker WCGT050304-X5 WK1 is a drill/boring indexable insert developed for holemaking operations that require consistent chip formation and dependable cutting-edge behaviour Trigon 80° geometry for stable cutting Uncoated carbide grade WK1 Chipbreaker X5 for effective chip control 7° clearance angle, 0.4 mm corner radius Consistent chip control that stabilises machining performance The insert is built around the chipbreaker X5, which promotes predictable chip segmentation and evacuation during drilling and boring cycles. Combined with the uncoated carbide WK1 grade, this design supports stable cutting forces and helps to reduce the risk of chip-related interruptions. For production environments where downtime affects throughput, the insert’s chip management contributes directly to improved cycle stability and fewer process disturbances. Geometry engineered for accuracy and repeatable tool life The Trigon 80° form and the modest corner radius 0.4 mm offer a balanced interaction between edge strength and cutting aggressiveness. A 7° clearance angle reduces flank contact and heat generation, supporting more even wear distribution across the insert and enhancing tool life. These geometry choices make the insert suitable for applications where hole accuracy and repeatability are necessary, delivering consistent axial and radial positioning in stacked production runs. Practical application notes and production benefits Designed for drilling and boring tool assemblies, the insert’s dimensions and thickness provide rigidity for demanding operations while remaining suitable for a wide range of holder systems. Material suitability should be verified against the manufacturer’s product matrix since the insert is supplied in an uncoated carbide variant; this ensures the right match for specific workpiece alloys and cutting parameters. The overall effect for workshops is improved process reliability and straightforward replacement handling, which supports leaner tool management and predictable production output. For tailored recommendations on Walter Tools inserts or to source the WCGT050304-X5 WK1 directly through Metav Werkzeuge, please contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for precise application support and availability Technical data Article number: WCGT050304-X5-WK1-WALTER Designation: WCGT050304-X5 WK1 Product type: Drill/boring indexable insert Manufacturer: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Numbers / Core technical data Free angle: 7° Corner radius: 0.4 mm Insert form: Trigon 80° Insert size: 05 Plate thickness: 03 Tolerance class: G Designs / Special features Grade: WK1 (uncoated carbide) Chipbreaker: X5 Execution: T Material: catalogue dependent Suitable for: check product matrix for material compatibility FAQ What is the primary benefit of the X5 chipbreaker on this insert? The X5 chipbreaker on the WCGT050304-X5 WK1 insert improves chip segmentation and evacuation, reducing the likelihood of clogging during drilling and boring tasks. Which tool geometry ensures stability when using this insert? The Trigon 80° geometry and the 0.4 mm corner radius of the WCGT050304-X5 WK1 provide a stable cutting profile that supports repeatable hole quality and even wear. Is the WK1 grade coated or uncoated, and what does that mean for application? WK1 is supplied as an uncoated carbide grade; this means verification against the product matrix is recommended to confirm suitability for specific workpiece materials and cutting conditions. Can the WCGT050304-X5 WK1 be used in existing drilling holders? The insert is dimensioned to fit standard drill/boring toolholders; however, compatibility should be confirmed with the holder manufacturer and the tooling catalogue for secure clamping and correct orientation. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanation only; there is no connection between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
WCGT050304-X5 WTP35 T Wendeplatten - Walter Tools
Take advantage of the combination of precise geometry, a WTP35 coated carbide grade and an effective X5 chipbreaker for consistent drilling and boring results; order directly via Metav Werkzeuge or consult our specialists for application support. WCGT050304-X5 WTP35 drilling/reaming indexable insert — Walter Tools, Trigon 80° with 0.4 mm corner radius The WCGT050304-X5 WTP35 is a triangle‑shaped, indexable insert designed for drilling and boring operations where stable chip control and repeatable bore quality are required. Trigon 80° insert form Coated carbide grade WTP35 Corner radius 0.4 mm, 7° clearance Stable cutting geometry for consistent bore quality The trigon geometry with an 80° form and a corner radius of 0.4 mm combines axial strength with a defined cutting edge, which reduces vibration in drilling and reaming cycles. The 7° clearance improves contact conditions at the cutting edge and lowers rubbing, so the tool sustains a controlled engagement with the material. Together with the X5 chipbreaker, this geometry delivers predictable chip formation and contributes to consistent surface finish and hole tolerance in serial production runs. Coated carbide grade that balances wear resistance and economy The insert is supplied in the WTP35 coated carbide grade, a Walter product family designed to offer a balanced combination of wear resistance and process reliability. The coating enhances thermal and abrasive resistance during interrupted or continuous drilling, extending effective tool life compared with uncoated grades. For operations where tool life and stable cutting behaviour translate directly into lower per‑hole cost, the WTP35 grade provides a pragmatic compromise between performance and economy — always verify the specific material suitability against the manufacturer’s product matrix. Quick indexation and simplified toolroom logistics As an indexable insert, the component allows rapid edge changes without the need to replace complete cutters, reducing machine downtime and simplifying inventory management. The insert’s designation and compact thickness code (03) make it compatible with standard Walter toolholders that accept the WCGT series profile, enabling fast changeover and repeatable positioning. This contributes to predictable cycle times in batch production and easier process control on the shop floor. Application guidance and compatibility notes Designed primarily for drilling and boring applications, the insert is best used with toolholders that match the WCGT050304-X5 geometry and secure stable clamping. The X5 chipbreaker is tuned for effective chip segmentation in medium cutting conditions; for different materials or highly interrupted cuts, consult the product matrix to confirm the optimal grade and chipbreaker combination. For assistance with toolholder compatibility or to determine whether this insert fits a specific machining setup, technical advice is available. Contact Metav Werkzeuge for tailored application advice, availability of Walter Tools WCGT050304-X5 WTP35 inserts and to request detailed machining recommendations; Metav Werkzeuge is ready to support setup and selection Technical Data Article number: WCGT050304-X5-WTP35-WALTER Designation: WCGT050304-X5 WTP35 Manufacturer: Walter Tools Core technical data Insert form: Trigon 80° Clearance angle: 7° Corner radius: 0.4 mm Size code: 05 Thickness code: 03 Chipbreaker: X5 Tolerance class: G Materials and special features Coated carbide grade: WTP35 (coated hard metal) Series: Walter cutting grade — open series Execution: T Designation without grade: WCGT050304-X5 FAQ What machining tasks is this insert intended for? The WCGT050304-X5 WTP35 insert from Walter Tools is intended for drilling and boring applications where a trigon form and controlled chipbreaking are advantageous. Can the WTP35 grade be used for stainless steel? WTP35 is a coated carbide grade; suitability for stainless steel depends on the specific workpiece material and cutting parameters — check the Walter product matrix or request advice for your application. How does the X5 chipbreaker affect performance? The X5 chipbreaker promotes segmented chip formation and improved evacuation during drilling and boring, which helps maintain consistent surface finish and reduces the risk of chip jamming. Is this insert compatible with standard WCGT toolholders? Yes, the WCGT050304-X5 geometry follows established indexable insert dimensions and is intended for holders that accept the WCGT family profile; confirm holder compatibility before first use. What is the benefit of the 0.4 mm corner radius? A 0.4 mm corner radius increases edge strength and contributes to improved hole tolerance and surface finish under axial loading typical of drilling and reaming operations. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are used solely for explanation and identification purposes. There is no affiliation between our company and the trademark holders. The offered item is an original, factory‑new product of the manufacturer.
WCGT050304-X5 WXM15 Wendeplatten - Walter Tools
Taking advantage of the combination of a Trigon 80° geometry, a sharp WXM15 uncoated carbide grade and a fine 0.4 mm corner radius delivers stable cutting, reliable chip control and consistent part quality when machining non‑ferrous metals; order the insert via Metav Werkzeuge or consult the sales team for process matching. WCGT050304-X5 WXM15 Drill/Reaming Indexable Insert, Trigon 80° — Walter Tools A WCGT050304-X5 WXM15 is a trigon 80° indexable insert engineered for drilling and reaming operations in non‑ferrous metals, offering precise engagement and controlled chip formation Trigon 80° geometry for secure cutting edge engagement Uncoated carbide grade WXM15 for NE‑metals machining X5 chipbreaker for predictable chip control 7° clearance angle for reduced rubbing 0.4 mm corner radius for fine edge stability Higher productivity through optimised geometry The insert’s Trigon 80° form is designed to deliver a controlled entry and exit during drilling and reaming, reducing vibration and improving hole quality. With a 7° clearance angle and a modest 0.4 mm corner radius, the geometry minimises rubbing while maintaining edge strength. These features translate into more consistent cycle times and fewer secondary finishing steps when working with aluminium, copper and brass, so machining sequences become more predictable and efficient. Grade and chip management tailored for NE‑metals Manufactured in the Walter WXM15 grade—an uncoated carbide composition—the insert favours sharp cutting edges and a low friction contact that prevents material adhesion common with soft metals. The integrated X5 chipbreaker encourages short, controllable chip formation which reduces the risk of chip entanglement in deep holes and supports steady coolant and evacuation behaviour. This combination of grade and chipbreaker improves tool life in non‑ferrous applications and supports repeatable surface finishes. Practical benefits at the machine and process level Using this insert means fewer interruptions for edge dressing and more predictable tool change intervals. The Trigon 80° shape and the WXM15 carbide are optimised for applications where sharpness and low built‑up edge are priorities, such as thin‑walled components or high‑feed reaming. The insert’s specification supports straightforward inventory management: consistent geometry and a clear grade designation simplify tool selection for workshop schedulers and process engineers. Compatibility, handling and selection advice The insert is intended specifically for non‑ferrous materials as defined by the Walter N‑grade system. It is not designed for hardened steels or high‑alloy materials. Selection should match spindle speed and feed to the workpiece alloy and hole depth; modest feeds and proper coolant or air blow‑out will prolong edge life. For integration into existing toolholders, verify seat and clamping compatibility with the WCGT050304-X5 designation and the Walter insert family to ensure secure seating and repeatable concentricity. For precision machining of non‑ferrous metals, contact Metav Werkzeuge for application advice or to order Walter Tools inserts from stock — email info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: WCGT050304-X5-WXM15-WALTER SKU: WCGT050304-X5-WXM15-WALTER Designation: WCGT050304-X5 WXM15 Facts Clearance angle: 7° Corner radius: 0.4 mm Thickness code: 03 Size code: 05 Tolerance class: G Special features Grade: uncoated carbide (WXM15) Geometry: Trigon 80° Chipbreaker: X5 Series: Walter N‑grade system Application focus: non‑ferrous metals (aluminium, copper, brass) FAQ Is this insert suitable for aluminium alloys? Yes. The insert in the WXM15 grade is optimised for aluminium and other non‑ferrous alloys, offering sharp cutting edges and low adhesion when used with appropriate feed and speed. Can the insert be used for stainless steel or hardened materials? No. The WXM15 grade and the Trigon 80° geometry are intended for non‑ferrous metals; they are not suitable for stainless steel or hardened workpieces. What does the X5 chipbreaker achieve in drilling and reaming? The X5 chipbreaker produces short, controllable chips that improve evacuation in through‑holes and reduce the risk of chip jamming during reaming operations. How is the insert referenced for ordering and toolset matching? Order using the designation WCGT050304-X5 WXM15 (Walter Tools), which identifies geometry, chipbreaker and grade for correct holder and process selection. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WCGT06T302-MN2 WNN10 Wendeplatten - Walter Tools
Take advantage of the combination of coated carbide grade WNN10, Trigon 80° geometry and a 0.2 mm corner radius to achieve consistent cutting performance and reliable chip control across mixed machining tasks. Order directly via Metav Werkzeuge or contact the consultants for application advice and availability. WCGT06T302-MN2 WNN10 — Trigon 80° indexable insert, 0.2 mm corner radius (Walter Tools) The WCGT06T302-MN2 WNN10 is a coated carbide Trigon 80° indexable insert designed for drilling, boring and turning operations in industrial machining, offering a balanced combination of accessibility and edge strength. Coated carbide grade WNN10 Trigon 80° insert geometry 0.2 mm corner radius MN2 chipbreaker for stable chips Consistent performance from a coated carbide grade The combination of WNN10 and a coated carbide substrate provides broadly applicable cutting behaviour that is suitable for many workshop and production contexts; material-specific suitability should be checked against the manufacturer’s product matrix. The coated surface improves wear resistance and helps maintain a sharp edge under varying cutting conditions, so process windows are widened and tool change frequency can be reduced. This results in more predictable cycle times and lower overall tooling costs when compared with uncoated grades. Geometry tuned for accessibility and edge security The Trigon 80° profile with a 0.2 mm corner radius has been selected to balance approach angle and edge robustness: the trigon shape allows good access in confined bores or interrupted cuts, while the modest corner radius distributes cutting forces to reduce edge chipping. The T3 plate thickness and insert size 06 contribute to mechanical stability, enabling the edge to withstand intermittent loads without sacrificing surface finish. These geometric choices promote repeatable results across series production. Reliable chip control and stable cutting A specific MN2 chipbreaker, combined with a 7° clearance, ensures predictable chip formation and evacuation in bore and turn operations. Controlled chips reduce the risk of built-up edge and improve machine uptime; chips are guided away from the cutting zone which aids coolant access and thermal control. The net effect is improved surface integrity on the workpiece and fewer interruptions for manual chip clearing during longer cycles. Built for productive workshop and production use Manufactured by a recognised brand, the insert is intended for productive metal-removal tasks where repeatable results and tool life are priorities. The coated cemented carbide (WNN10) composition and the open series designation mean the insert is provided as a standard production item; users will benefit from consistent batch-to-batch quality and straightforward replacement in toolholders. For specific alloys and hardened materials, the suitability must be verified using the product’s technical matrix to ensure optimal cutting data and safety margins. Contact Metav Werkzeuge for detailed application support and to secure WCGT06T302-MN2 WNN10 inserts for reliable production processes Technical data Article number: WCGT06T302-MN2-WNN10-WALTER Designation: WCGT06T302-MN2 WNN10 Product type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.2 mm Plate form: Trigon 80° Plate size: 06 Plate thickness: T3 Tolerance class: G Special features Chipbreaker: MN2 Carbide grade: coated cemented carbide (WNN10) Series: Walter Schneidstoffsorte - Serie offen Execution: T Material: catalogue dependent FAQ What materials is this insert suited for? The insert is produced in the WNN10 coated carbide grade; material suitability depends on the specific workpiece and should be verified against the manufacturer’s product matrix for the WCGT06T302-MN2 WNN10 item. How does the MN2 chipbreaker improve machining? The MN2 chipbreaker promotes stable chip formation and evacuation, which reduces the risk of built-up edge and improves surface finish when the WCGT06T302-MN2 WNN10 insert is used in drilling or turning operations. What does the Trigon 80° form allow in practice? The Trigon 80° geometry offers improved access for bore-related tasks and interrupted cuts while maintaining a favourable approach angle for consistent cutting forces. Is the corner radius suitable for heavy-duty cutting? The 0.2 mm corner radius provides a compromise between edge strength and sharpness; it suits applications where a robust edge is needed without overly increasing cutting forces. Where can additional technical data be obtained? Detailed cutting parameters and the full product matrix for the WCGT06T302-MN2 WNN10 insert are available from Metav Werkzeuge and from the manufacturer’s technical literature. Walter AG (brand: Walter Tools) is among the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and product names are the property of their respective owners. Mention of brand names and trademarks is for explanation only and does not indicate any association between Metav Werkzeuge and the listed brands. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
WCGT06T304-FN2 WNN10 Wendeplatten - Walter Tools
Take advantage of a combination of reliable chip control, robust geometry and catalogue‑dependent grade selection for consistent machining results; the coated carbide grade WNN10 and the FN2 chipbreaker deliver controlled chip formation and stable cutting, while the trigon shape and 7° clearance support secure tool engagement. Order the insert directly via Metav Werkzeuge or ask our consultants for application advice. WCGT06T304-FN2 WNN10 — Trigon 80° indexable insert, FN2 chipbreaker — Walter Tools The WCGT06T304-FN2 WNN10 is a coated carbide indexable insert, designed for combined drilling and turning operations with a Trigon 80° form and a controlled FN2 chipbreaker for reliable chip evacuation. Coated carbide grade WNN10 Trigon 80° insert form 7° clearance angle for secure cutting FN2 chipbreaker for controlled chips Consistent productivity through engineered geometry and grade selection The insert’s Trigon 80° profile and 7° clearance deliver a predictable cutting engagement that reduces vibration and supports steady material removal rates. With a coated carbide substrate optimised for general-purpose turning and drilling tasks, the geometry helps maintain a consistent cutting edge under varying feed conditions, which leads to fewer interruptions in production and improved overall throughput. Precise chip control for safer machining Equipped with the FN2 chipbreaker, the component controls chip form effectively across a range of cutting depths. This results in short, controlled chips that reduce the risk of workpiece and tool damage and simplify swarf management. The improved chip behaviour contributes directly to process reliability and cleaner machining environments in both manual and CNC setups. Designed for repeatable accuracy and stability The combination of T3 thickness and a corner radius of 0.4 mm provides a balance between edge strength and surface finish capability. The insert’s mechanical stability supports reproducible results when performing finishing passes or interrupted cuts, enabling consistent dimensional quality and fewer adjustments on the machine. Flexible applicability across typical workshop materials While the exact material suitability is catalogue‑dependent, the WNN10 coated grade is intended as a versatile carbide option that covers a broad range of common engineering materials. Check the product matrix in the catalogue for specific material matches; the insert is intended to provide a pragmatic balance between wear resistance and edge toughness for general machining tasks. Easy integration into existing tooling systems The insert’s industry‑standard form and designation make retrofitting into compatible holders straightforward. Its WCGT06T304-FN2 designation identifies the geometry, chipbreaker and grade so toolroom planners can match inserts to holders and machining strategies quickly, reducing setup time and simplifying tool inventory management. Focus on production safety and lower overall operating costs By combining controlled chip formation, robust geometry and a coated carbide cutting substrate, the insert reduces unplanned tool changes and supports longer, more predictable tool life. The result is increased uptime and a more economical machining routine without compromise to surface integrity or repeatability. For specific application support or to place an order, contact Metav Werkzeuge — info@metav-werkzeuge.com or +49 2822 7131930 — our specialists will advise on insert selection and suitability for the intended machining task. Technical data Article number: WCGT06T304-FN2-WNN10-WALTER Designation: WCGT06T304-FN2 ISO designation: WCGT06T304-FN2 WNN10 Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.4 mm Insert form: Trigon 80° Insert size: 06 Thickness: T3 Tolerance class: G Special features Chipbreaker: FN2 Coating / grade: WNN10 (coated carbide) Series: Walter grade series — open series Execution: T Material specification: catalogue‑dependent FAQ What materials is this insert suitable for? The insert is supplied in the WNN10 coated carbide grade; material suitability should be checked in the product matrix but the grade is intended as a versatile option for a broad range of engineering materials. How does the FN2 chipbreaker affect performance? The FN2 chipbreaker produces short, controlled chips that improve swarf handling and reduce the risk of chip entanglement, contributing to safer and more stable machining. Can this insert be used for both drilling and turning operations? Yes, the geometry and designation indicate suitability for combined drilling and turning tasks when mounted in compatible tooling systems and appropriate holders are used. What role does the Trigon 80° form play in machining? The Trigon 80° profile offers a secure cutting engagement and good edge strength, aiding stability in interrupted cuts and supporting consistent surface quality. Is the grade information fixed or catalog‑dependent? The WNN10 grade is specified for this item, but additional material and grade recommendations are catalogue‑dependent; consult the product matrix for precise matches. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned solely for explanatory purposes and do not indicate any partnership or endorsement. The offered item is an original, brand‑new product from the manufacturer.
WCGT06T304-MN2 WNN10 Wendeplatten - Walter Tools
Take advantage of stable chip formation and a durable, coated carbide grade that supports consistent turning and boring results; the Trigon 80° geometry with a 0.4 mm nose radius and 7° clearance angle delivers improved surface finish and reduced tool pressure. Order or request application advice via Metav Werkzeuge for assured production compatibility. WCGT06T304-MN2 WNN10 — Indexable turning and boring insert, Trigon 80°, 0.4 mm The WCGT06T304-MN2 WNN10 is a coated carbide insert designed for turning and internal boring where stable chip control and repeatable surface quality are required in general machining applications. Trigon 80° geometry for versatile turning 0.4 mm nose radius for fine surface finishes 7° clearance angle reduces rubbing Coated carbide grade WNN10 for extended tool life Consistent machining through defined geometry and clearance The Trigon 80° form combines rigidity with accessibility, making the insert suitable for a wide range of turning and boring tasks where reliable cutting behaviour is essential. The 0.4 mm nose radius improves the surface finish on circumferential cuts while limiting the risk of chatter on lean setups. Meanwhile, the 7° clearance angle reduces flank contact and diminishes rubbing, which in turn lowers cutting temperatures and helps preserve the cutting edge for longer. These geometric choices translate directly into fewer rework cycles and more predictable part outcomes. Coating and grade: what WNN10 offers to production WNN10 is a coated carbide grade from Walter Tools intended for robust, general-purpose performance. The coating supports wear resistance and helps maintain a sharp cutting edge under variable feeds and speeds; coated grades typically reduce built-up edge and improve lifetime versus uncoated carbide in many operations. The included chipbreaker designation MN2 indicates a medium chip control geometry designed to produce manageable swarf in standard materials; for specialised alloys or specific feed ranges, a quick check of the product matrix is recommended to confirm the best match. Practical integration and benefits on the shop floor As an indexable insert in size 06 with thickness T3, this component simplifies inventory and changeover compared with solid-tool approaches. The Trigon 80° format enables turning and some light profiling with fewer insert variants, while the coated carbide construction promotes stable chip formation and repeatable part quality. For engineering teams seeking predictable cycle times and reduced tool-change frequency, the balanced combination of geometry, grade and chipformer reduces downtime and supports continuous production. For application advice on the WCGT06T304-MN2 WNN10 insert or to discuss batch availability and suitable cutting parameters, contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: WCGT06T304-MN2-WNN10-WALTER ISO designation: WCGT06T304-MN2 WNN10 Product type: Indexable turning/boring insert Facts Plate form: Trigon 80° Clearance angle: 7° Nose radius: 0.4 mm Plate size: 06 Thickness: T3 Tolerance class: G Special features Grade: WNN10 (coated carbide) Chipbreaker: MN2 Series: Walter Schneidstoffsorte - Serie offen Style/designation: T Sort description: coated carbide FAQ What materials is this insert suitable for? The WCGT06T304-MN2 WNN10 insert, produced by Walter Tools, is a coated carbide grade intended for a broad range of general turning applications; check the manufacturer matrix for specific material compatibility. How does the MN2 chipbreaker affect machining? The MN2 chipformer on the WCGT06T304-MN2 WNN10 promotes medium chip control, producing manageable swarf for standard feeds and speeds and contributing to consistent surface quality. Can this insert be used for internal boring and external turning? Yes—its Trigon 80° geometry and 0.4 mm nose radius make the insert suitable for both external turning and certain internal boring operations where the toolholder and setup allow. What benefit does the 7° clearance angle provide? The 7° clearance reduces flank contact and rubbing during cutting, lowering friction and helping to prolong the effective cutting edge life of the WCGT06T304-MN2 WNN10 insert. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand presentation: Walter Tools) is a leading provider of precision metalworking tools. Protected trademarks and trade names belong to their respective owners. Brand names and designations are used only for explanatory purposes. The offered item is original, factory-new merchandise of the manufacturer.
WCGT06T308-FN2 WNN10 Wendeplatten - Walter Tools
Benefit from a combination of precise geometry, a robust WNN10 coated grade and a controlled chipbreaker that deliver stable cutting and predictable tool life. Optimise drilling and turning operations with the Trigon 80° design and 0.8 mm nose radius for consistent surface quality. Order directly via Metav Werkzeuge or contact our consultants for application advice. WCGT06T308-FN2 WNN10 Trigon 80° insert for drilling, boring and turning — Walter Tools WCGT06T308-FN2 WNN10 is an indexable cutting insert designed for combined drilling/boring and turning applications, offering a trigon geometry for versatile chip control and reliable edge stability Trigon 80° geometry 0.8 mm nose radius 7° clearance angle FN2 chipbreaker WNN10 coated carbide grade Consistent cutting performance for mixed operations The Trigon 80° geometry combined with the FN2 chipbreaker ensures reliable chip formation across interrupted cuts and continuous turning passes. The triangular shape provides three usable cutting edges per index, increasing economy in production, while the 0.8 mm nose radius supports repeatable surface finish without aggressive forces. For drilling and boring sequences where tool run-out and stability matter, the insert’s form contributes to predictable cutting behaviour and simplified tool-preset routines. The result is reduced machining downtime and more stable process windows. Material compatibility and grade benefits explained The insert is supplied in the WNN10 grade, a coated carbide type developed for broad material coverage; check the specific product matrix for exact suitability. Coated carbides combine a wear-resistant surface layer with a tough substrate to resist chipping during interrupted cuts. In practice, this means longer edge life when facing common workshop steels and mixed-material batches. The 7° clearance angle moderates rubbing at the flank, reducing heat build-up and preserving edge geometry under standard cutting parameters. Practical advantages in workshop workflows Using a standard indexable format simplifies tool inventory and reduces set-up time: multiple edges per insert lower consumption and the consistent seating of the insert facilitates repeatable tool offsets. The T3 thickness and the insert size designated as 06 give a compact profile suitable for smaller holders and close-tolerance operations. With a high degree of process reliability offered by the geometry and grade combination, tool changes become less frequent and productivity improves across batch and one-off production. What to expect in application and optimisation When integrating this insert into a machining cycle, anticipate improved surface integrity on turned and bored features thanks to the balanced edge form and chip control. Adjust feeds and speeds according to the workpiece material and machine capability; the robust design supports moderate to demanding feeds while keeping burr formation and vibration in check. For best results, align coolant strategy and holder rigidity with the intended operation to exploit the WNN10 coating’s wear resistance and ensure consistent part quality. Contact Metav Werkzeuge for tailored recommendations on Walter Tools inserts and to discuss the ideal cutting parameters for specific materials and machines Technical data Article number: WCGT06T308-FN2-WNN10-WALTER Designation: WCGT06T308-FN2 ISO designation: WCGT06T308-FN2 WNN10 Product type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Manufacturer: Walter Tools Facts Insert size: 06 Thickness: T3 Nose radius: 0.8 mm Clearance angle: 7° Nose angle: 80° Tolerance class: G Special features Chipbreaker type: FN2 Grade: WNN10 (coated carbide) Series: Walter Schneidstoffsorte - Serie offen Plate form: Trigon 80° Material: katalogabhängig FAQ What materials is this insert suitable for? The WCGT06T308-FN2 WNN10 insert is produced in the WNN10 coated carbide grade; suitability depends on the product matrix, so check the matrix for compatibility with specific steels and non-ferrous materials. Can the insert be used for both drilling and turning operations? Yes, the trigon geometry and FN2 chipbreaker allow the insert to perform in combined drilling/boring and turning tasks, offering versatility for mixed-process tool sets. How many usable cutting edges does the insert provide? The trigon form delivers three cutting edges per insert, increasing economy and reducing the frequency of index changes in production. What performance benefit does the 0.8 mm nose radius deliver? A 0.8 mm nose radius balances surface finish and edge strength, improving final part quality while resisting minor impact and edge wear during interrupted cuts. Is special coolant or tooling required for best results? Standard coolant strategies are generally suitable; optimal results depend on holder rigidity and cutting data. Fine-tune coolant flow and speeds to the workpiece material and machine stability. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Die Walter AG (brand appearance: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names remain the property of their respective owners; brand names are mentioned for explanatory purposes only and do not imply any affiliation between our company and the manufacturers.
WCGT080404-MN2 WNN10 WNN10 Wendeplatten - Walter Tools
Take advantage of the combination of precise geometry and a controlled chipformer for steady productivity in turning and boring operations; order the insert directly via Metav Werkzeuge or consult the team for application-specific advice. WCGT080404-MN2 WNN10 — Boring and Turning Indexable Insert, Trigon 80°, Walter Tools WCGT080404-MN2 WNN10 is an indexable insert designed for turning and boring tasks, featuring a Trigon 80° shape, a 0.4 mm corner radius and an MN2 chipbreaker for predictable chip control across a range of catalog-dependent grades. Trigon 80° geometry for secure positioning WNN10 coated carbide for broad material coverage MN2 chipbreaker for consistent chip formation 7° clearance angle and 0.4 mm corner radius Stable chip control for reliable productivity The Trigon 80° geometry combined with the MN2 chipbreaker delivers controlled chip formation, reducing variability in cycle times and easing swarf handling. The combination of geometry and chipformer is tailored for medium to general machining tasks and supports steady productivity in series production. The controlled chip flow reduces stoppages and contributes to lower tool-change frequency, which benefits overall process efficiency and line uptime. Geometry and grade tailored for flexible machining The insert’s Trigon 80° profile and 0.4 mm corner radius enable robust edge strength while maintaining the ability to produce consistent surface finishes. The grade is listed as WNN10 (coated carbide) and is catalogue-dependent; this means the substrate and specific coating options vary by catalogue entry to match the workpiece material and cutting conditions. Check the product matrix to confirm the optimal combination of substrate and coating for the intended application. Precision fit and cutting clearance for repeatable results A 7° clearance angle supports effective cutting engagement and helps avoid rubbing during depth changes or bore entry. The standardised geometry and tolerance class ensure repeatable seating and indexing in compatible toolholders, simplifying tool management and reducing set-up time between jobs. Together, these attributes help maintain part tolerances and reduce scrap rates in production environments. Selection and application guidance for process security Grade choice and coating options influence wear behaviour and should be selected against the workpiece material and machining strategy; consult the product matrix for suitability. As the WNN10 grade is a coated carbide class, it is intended to balance wear resistance and edge toughness for a wide range of materials — final selection depends on the required surface quality and cycle time targets. For critical or mixed-material batches, select the catalogue variant that best aligns with cutting speed and feed parameters. Contact Metav Werkzeuge for tailored application advice on Walter Tools inserts and to secure the correct WNN10 variant for the machining task — eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 Technical data Article number: WCGT080404-MN2-WNN10-WALTER SKU: WCGT080404-MN2-WNN10-WALTER Designation: WCGT080404-MN2 WNN10 Product type: Bohr-/Aufbohrwendeschneidplatte / Drehwendeschneidplatte Key dimensions Insert size: 08 Thickness code: 04 Corner radius: 0.4 mm Clearance angle: 7° Shape: Trigon 80° Tolerance class: G Materials & special features Grade: WNN10 (coated carbide) Chipformer: MN2 Series: Walter Schneidstoffsorte - Serie offen Substrate/coating: Catalogue-dependent Notes: Check product matrix for workpiece suitability FAQ What applications is this insert suited for? This insert is intended for turning and boring operations where the Trigon 80° geometry and MN2 chipbreaker support controlled chip formation and repeatable results. Can the WNN10 grade be used on hardened steels? The WNN10 grade is a coated carbide class; suitability for hardened steels must be checked in the product matrix to confirm the correct catalogue variant and cutting parameters. How does the 0.4 mm corner radius affect finishing? A 0.4 mm corner radius provides a balance between edge strength and surface finish, improving edge life while still allowing acceptable surface quality in many turning applications. Is the insert compatible with standard toolholders? The Trigon 80° form and tolerance class G support secure seating in compatible indexable insert toolholders; verify holder compatibility by size code and clamping style. What is the role of the MN2 chipbreaker? The MN2 chipbreaker is designed for predictable chip control in general machining, improving swarf management and reducing interruptions from poor chip formation. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WCGT080408-MN2 WNN10 MN2 Wendeplatten - Walter Tools
Taking advantage of the insert's coated carbide grade and MN2 chipbreaker provides stable chip control and predictable tool life, supporting efficient, continuous machining. Order the WCGT080408-MN2 WNN10 directly via Metav Werkzeuge or consult the technical team for material-specific recommendations. WCGT080408-MN2 WNN10 trigon insert for drilling and turning, Walter Tools — coated carbide, MN2 chipbreaker WCGT080408-MN2 WNN10 is an indexable trigon insert designed for combined drilling and turning applications, offering a robust coated-carbide construction and a chipbreaker optimised for consistent material removal. Coated carbide for long tool life Trigon 80° geometry for stable engagement Corner radius 0.8 mm for reliable edge strength 7° clearance angle for smooth entry Maximise process reliability with consistent chip control The insert’s chipbreaker MN2 is engineered to produce predictable, controllable chips, which reduces the risk of built-up edge and machine stoppages. The coated carbide substrate enhances wear resistance under interrupted cuts, meaning fewer insert changes and less downtime. For users planning production runs, this performance translates into a measurable increase in machine availability and process stability. Check the manufacturer’s product matrix to confirm compatibility with specific workpiece materials before application. Simplified setup and secure cutting geometry for repeatable results With a trigon 80° form and a corner radius 0.8 mm, the geometry promotes stable seating in the toolholder and good edge strength during entry and exit. The 7° clearance reduces rubbing and helps maintain cutting temperatures within an optimal range, improving surface finish and reducing flank wear. These geometric choices make toolpath programming and fixture set-up more predictable, which in turn shortens lead times in the set-up phase and supports repeatable part quality. Optimised for production: balance of economy and performance This insert is supplied in a tolerance class G, providing consistent dimensions for high-repeatability mounting and minimal index offset. The coated-carbide grade of the WNN10 series aims to strike a balance between wear resistance and sharpness, offering a cost-effective solution for many machining tasks. Because the material specification is catalogue-dependent, process planners are advised to consult the technical documentation to select the precise grade that matches cutting speed and workpiece material requirements. Contact Metav Werkzeuge to discuss suitability of the Walter Tools WCGT080408-MN2 WNN10 for specific production needs or request the product matrix by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: WCGT080408-MN2-WNN10-WALTER Designation: WCGT080408-MN2 WNN10 Manufacturer: Walter Tools Facts Plate form: Trigon 80° Plate size: 08 Plate thickness: 04 Corner radius: 0.8 mm Clearance angle: 7° Tolerance class: G Special features Coating: coated carbide (WNN10) Chipbreaker: MN2 Series: Walter Schneidstoffsorte - Serie offen Execution: T Material: Catalogue dependent FAQ What machining tasks is this insert intended for? The insert is designed for combined drilling and turning operations where a trigon 80° geometry and chipbreaker MN2 improve chip control and cutting stability. Is the WCGT080408-MN2 WNN10 suitable for stainless or hardened steels? Material suitability should be verified against the Walter Tools product matrix; the WNN10 is a coated-carbide grade intended for broad applications but exact performance depends on the selected grade variant. How does the MN2 chipbreaker benefit production runs? The MN2 chipbreaker produces consistent chip shapes that reduce interruptions, improving machine uptime and enabling longer uninterrupted cutting periods. What does tolerance class G mean for everyday use? Tolerance class G indicates precise, repeatable dimensions for the insert, which helps ensure consistent seating and predictable machining results when indexing inserts. Can the insert geometry improve surface finish? Yes — the combination of a 7° clearance angle and optimised corner radius contributes to smoother tool entry and exit, often resulting in improved workpiece surface quality. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com