WNMG060404-MM5 WMP20S WMP20S Wendeplatten - Walter Tools
Take advantage of the combination of proven process security, durable coated grade and robust geometry for reliable machining of stainless steel; order the insert via Metav Werkzeuge or consult our specialists for application-specific recommendations. WNMG060404-MM5 WMP20S — Trigon 80° indexable turning insert for stainless steel, Tiger·tec Silver, Walter Tools WNMG060404-MM5 WMP20S is an indexable turning insert designed for secure, repeatable performance in demanding stainless steel applications, combining a Trigon 80° form with the Tiger·tec Silver coated grade for stable cutting. Tiger·tec Silver coated grade WMP20S MM5 chipbreaker for controlled chips Trigon 80° form for secure seating 0.4 mm corner radius for robust edges Optimised cutting performance for stainless steel The insert delivers consistent metal‑cutting performance under the specific challenges posed by stainless steel such as high toughness and heat generation. The WMP20S grade, developed within the Tiger·tec Silver family, is a coated cemented carbide designed to improve heat resistance and preserve the cutting edge. This results in more reliable chip formation, reduced risk of built‑up edge and longer effective tool life in medium to robust machining conditions. The combination of grade and coating directly reduces downtime by extending the intervals between indexings and insert changes. Controlled chips and stable geometry for reproducible surfaces Chip management and edge strength are central to reproducible machining results. The MM5 chipbreaker is tailored to produce consistent chip shapes when machining stainless materials, which helps to avoid tangling and protects the workpiece finish. The Trigon 80° form provides a compact seating and three usable cutting edges per insert, while the 0.4 mm corner radius increases edge robustness for interrupted or heavier cuts. The 0° (negative) clearance contributes to edge strength and stability, supporting process security when depth of cut or feed varies. Process reliability and economical operation By combining a modern coated grade with a conservative, strong geometry, this insert supports stable performance across batch and single‑part production. The construction targets longer edge life and consistent dimensional outcomes, which simplifies tool inventory planning and reduces rework. For operations seeking predictable cycle times and surface quality on stainless steel, the insert offers an economic balance between wear resistance and cutting capability. The proven material and geometry synergy makes it suitable for workshops that prioritise repeatability and low variation in production. For tailored advice on using the Walter Tools Tiger·tec Silver WMP20S insert in specific stainless steel applications, contact Metav Werkzeuge: info@metav-werkzeuge.com or +49 2822 7131930 — our technical consultants will recommend the optimal cutting data and holder setup. Technical Data Article number: WNMG060404-MM5-WMP20S-WALTER Label: Drehwendeschneidplatte WNMG060404-MM5 WMP20S Walter Tools Manufacturer: Walter Tools Product type: Drehwendeschneidplatte Series: Tiger-tec Silver Grade: WMP20S Chipbreaker: MM5 Shape: Trigon 80° Size designation: 06 Corner radius: 0,4 Clearance angle: 0° (negativ) Thickness designation: 04 ISO designation: WNMG060404-MM5 WMP20S UID: WNMG060404-MM5-WMP20S-WALTER Facts Size: 06 Corner radius: 0.4 mm Clearance angle: 0° (negative) Thickness designation: 04 Special features Coating / technology: Tiger·tec Silver Grade type: coated cemented carbide (WMP20S) Chip control: MM5 chipbreaker Form / seating: Trigon 80° Application suitability: stainless steel FAQ Which materials is this insert designed for? The WNMG060404-MM5 WMP20S insert from Walter Tools is specified for machining stainless steel and is tuned to the typical demands of these materials. What is the advantage of the Tiger·tec Silver WMP20S grade? The Tiger·tec Silver WMP20S coated grade provides improved heat resistance and edge stability for tougher cutting conditions, extending effective tool life on stainless steel. How does the MM5 chipbreaker affect machining? The MM5 chipbreaker promotes controlled chip formation with consistent shapes, supporting clean evacuation and improved surface quality during turning operations. Is the Trigon 80° form suitable for interrupted cuts? The Trigon 80° geometry together with a 0.4 mm corner radius and a 0° negative clearance increases edge strength, making the insert appropriate for more robust and intermittently loaded cut conditions. How many cutting edges are available per insert? The trigon form provides multiple indexable cutting edges per insert; the product designation WNMG060404-MM5 WMP20S indicates the standard indexable insert format used in turning toolholders. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
WNMG060404-MM5 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, a robust WSM10S grade and the MM5 chipbreaker for consistent chip control and long cutting-edge life; the result is a reliable solution for machining demanding materials with reduced downtime. Order the insert directly via Metav Werkzeuge or ask our consultants if needed. WNMG060404-MM5 WSM10S — indexable turning insert by Walter Tools (Tiger·tec Silver, for stainless steels & superalloys) WNMG060404-MM5 WSM10S is an indexable turning insert designed for heavy-duty performance when machining heat-resistant alloys and stainless steels Tiger·tec Silver coating for thermal stability Optimised MM5 chipbreaker for controlled chips Trigon 80° shape for stable cutting edges 0.4 mm corner radius for consistent finishes Durable edge performance for tough alloys The combination of the WSM10S grade with the Tiger·tec Silver coating provides enhanced resistance to thermal and mechanical wear when working with difficult-to-cut materials. The coated carbide formulation supports stable chip formation and protects the cutting edge against premature failure, which translates into fewer tool changes and higher throughput. In practice, this means more consistent component quality when turning stainless steels and superalloys, and a predictable tool life that benefits production planning. Geometry engineered for process stability and surface quality The Trigon 80° insert form and the MM5 chipbreaker work together to deliver controlled chip segmentation and secure contact at the cutting edge. A 0.4 mm corner radius helps achieve repeatable surface finishes while reducing the risk of edge chipping during interrupted cuts. The negative 0° relief angle contributes to a robust edge geometry that resists build-up and deformation under high thermal loads; negative rake geometries often improve stability on heavy cuts and interrupted turning. These geometric choices increase productivity by enabling higher cutting forces with reliable results. Practical application and compatibility for workshop integration Designed as an indexable turning insert, this grade fits standard WNMG pockets and tolerates the generally demanding conditions of machining heat-resistant alloys and stainless materials. The tolerance class M and execution G ensure consistent dimensions for accurate seating and repeatable performance in turret or toolholder systems. Because cutting parameters vary by machine and workpiece, the stable behaviour of this insert simplifies machining strategy: fewer trial runs, quicker ramp-up to production speeds and more predictable cycle times for batch work. For precision turning of stainless steels and superalloys, contact Metav Werkzeuge to discuss Walter Tools Tiger·tec Silver WSM10S inserts and to receive tailored application advice and ordering assistance. Technical data SKU: WNMG060404-MM5-WSM10S-WALTER Article designation: WNMG060404-MM5 WSM10S Brand: Walter Tools Product type: indexable turning insert Series: Tiger·tec Silver Core figures Corner radius: 0.4 mm Relief angle: 0° (negative) Insert form: Trigon 80° Size: 06 Thickness: 04 Tolerance class: M Materials & features Grade: WSM10S Chipbreaker: MM5 Applicable materials: S / M (superalloys, stainless steels) Execution: G Product category: Drehwendeschneidplatte FAQ What materials is this insert suited for? The WNMG060404-MM5 WSM10S insert is engineered for stainless steels and heat-resistant superalloys (ISO groups M and S), delivering secure chip control and thermal stability on these demanding materials. How does the Tiger·tec Silver coating benefit machining? The Tiger·tec Silver coating increases resistance to thermal and abrasive wear, helping the insert maintain a sharp, stable cutting edge and reducing the frequency of tool changes during production. What is the role of the MM5 chipbreaker? The MM5 chipbreaker produces controlled, manageable chips and supports consistent surface quality, which improves process safety and reduces the risk of chip-related interruptions. Why choose a Trigon 80° insert shape? A Trigon 80° form offers a robust cutting edge geometry and good support in the tool pocket, enhancing stability during turning and making it suitable for heavier cuts and varied workpiece geometries. What does tolerance class M indicate? Tolerance class M refers to the dimensional accuracy of the insert, ensuring consistent seating and repeatable performance in compatible toolholders for industrial turning applications. Walter Tools (Walter AG); Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation. There is no affiliation or connection between our company and the manufacturers named. The offered item is an original, factory-new product of the manufacturer (Walter Tools).
WNMG060404-MM5 WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of durable coated carbide, precise Trigon geometry and reliable chip control for consistent turning of stainless steel and superalloys; order directly via Metav Werkzeuge or ask our consultants for tailored advice. WNMG060404-MM5 WSM20S — Trigon 80° turning insert, Tiger·tec Silver, Walter Tools The WNMG060404-MM5 WSM20S is a Trigon 80° turning insert developed for demanding turning operations on stainless steel and heat-resistant superalloys, offering a balance of edge stability and controlled chip formation. Tiger·tec Silver coated carbide WSM20S grade for tough alloys Trigon 80° form, 0.4 mm corner Chipbreaker MM5 for stable chips High-performance machining where stability matters The insert’s Tiger·tec Silver technology and WSM20S grade provide a hardwearing, coated carbide cutting edge engineered for materials that generate heat and strain the tool edge. The chipbreaker MM5 promotes predictable chip formation, which reduces interruptions and the risk of built-up edge when machining stainless steel or nickel-based alloys. Explained simply: the coating increases thermal resistance and edge life, while the chipbreaker geometry shapes and ejects swarf to maintain a steady cut — a direct benefit to throughput and tool change intervals. Consistent surface quality and reduced rework A Trigon 80° form combined with a 0.4 mm corner radius delivers a robust cutting geometry that supports repeatable finishes on complex workpieces. The negative 0° relief helps absorb cutting forces during heavier cuts, so dimensional stability is improved and secondary finishing steps are less frequent. The tolerance class M ensures batch-to-batch uniformity, which is especially valuable for serial production where interchangeability and predictable tool behaviour translate into lower scrap rates and higher overall equipment effectiveness. Integration into the workshop and application guidance The insert is designed for standard WNMG toolholders and is available in the established WNMG060404-MM5 format, facilitating straightforward replacement and setup in turning centres. Material suitability is indicated by ISO groups M and S, meaning primary applications are stainless steel and heat-resistant superalloys or titanium alloys; this informs tool selection and machining strategies without the need for extensive trial runs. For difficult-to-machine alloys, combining the WSM20S grade with stable fixturing and appropriate coolant strategy improves process security and surface integrity. For a consultation on optimising turning processes with Walter Tools' Tiger·tec Silver inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the best grade and geometry for the application. Technical data Article number: WNMG060404-MM5-WSM20S-WALTER Designation: WNMG060404-MM5 SKU: WNMG060404-MM5-WSM20S-WALTER Manufacturer: Walter Tools Facts Plate size: 06 Plate thickness: 04 Plate form: Trigon 80° Corner radius: 0.4 mm Relief angle: 0° (negative) Tolerance class: M Special features Series: Tiger·tec Silver Grade: WSM20S (coated carbide) Chipbreaker: MM5 Material suitability: S / M (superalloys and stainless steel) Version / execution: G FAQ What materials is this insert suitable for? The WNMG060404-MM5 WSM20S turning insert from Walter Tools is suitable for ISO groups S and M, specifically heat-resistant superalloys and stainless steel. How does the Tiger·tec Silver coating help in production? The Tiger·tec Silver coating on the WNMG060404-MM5 WSM20S improves thermal resistance and wear properties, extending cutting-edge life and stabilising performance under high temperatures. Which chip characteristics can be expected with the MM5 breaker? The chipbreaker MM5 on this Walter Tools insert produces compact, controllable chips that reduce entanglement and support uninterrupted machining cycles. Is the Trigon 80° form suitable for heavy cuts? Yes, the Trigon 80° form and negative 0° relief of the WNMG060404-MM5 insert provide the rigidity required for heavier turning operations while maintaining dimensional stability. What tolerance and repeatability does this insert offer? The insert is manufactured to tolerance class M, ensuring consistent dimensions and reliable repeatability across production batches. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany. Protected trademarks and trade names are the property of their respective owners. Brand names are used solely for identification and explanation. The offered article is an original, factory‑new product of the manufacturer.
WNMG060404-MM5 WSM30S WSM30S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the WSM30S grade for secure chip formation and extended edge life on stainless steels and high-temperature alloys; order directly via Metav Werkzeuge or consult our team for application advice. WNMG060404-MM5 WSM30S indexable turning insert — Trigon 80° geometry, Tiger·tec Silver (Walter Tools) The WNMG060404-MM5 WSM30S is an indexable turning insert designed for demanding turning of stainless steels and heat‑resistant superalloys, combining a trigon 80° form with a robust MM5 chipbreaker for controlled chips and consistent surface finish. Tiger·tec Silver coated carbide Designed for stainless steels and superalloys Trigon 80° geometry for versatile turning 0° negative rake angle for edge stability Increased process security through advanced coating and grade The coated WSM30S grade, part of the Tiger·tec Silver series, delivers enhanced thermal resistance and wear behaviour when machining stainless steels and temperature‑resistant alloys. The combination of a robust coated carbide substrate and optimised coating chemistry promotes stable chip formation and reduces the risk of built‑up edge, which is critical for consistent batch production. For workshops seeking predictable tool life, this insert supports repeatable cycle times and fewer tool changes. Geometry and chip control that improve surface quality A Trigon 80° form with a 0° negative rake and a 0.4 mm corner radius provides a balance between strength and accessibility in interrupted or heavy cuts. The dedicated MM5 chipbreaker is engineered to fragment chips effectively in materials prone to long, stringy swarf, thereby improving machine uptime and reducing manual chip handling. These geometric choices result in better surface integrity and simplified post‑process handling in both roughing and semi‑finishing operations. Clear benefits for demanding materials and applications The insert’s specification targets machining of stainless steels (M) and superalloys/titanium (S) as defined in ISO categories, where thermal load and material toughness challenge tool edges. By using a grade optimised for heat resistance and edge stability, the insert lowers the incidence of premature flank wear and edge failure. In practical terms, this translates into higher productivity and a more reliable process window for manufacturers working with corrosion‑resistant components or high‑temperature alloys. Discuss application suitability and supply options with Metav Werkzeuge — our specialists can advise on the best Walter Tools Tiger·tec Silver inserts for specific stainless steel or superalloy tasks; contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: WNMG060404-MM5-WSM30S-WALTER Designation: WNMG060404-MM5 WSM30S Series: Tiger·tec Silver Grade: WSM30S Core specifications Geometry: Trigon 80° Size: 06 Thickness: 04 Corner radius: 0.4 mm Rake angle: 0° (negative) Special features Chipbreaker: MM5 Suitable for: stainless steels (M) Suitable for: superalloys and titanium (S) Execution: G Tolerance class: M FAQ What materials is this insert suitable for? The WNMG060404-MM5 WSM30S insert is intended for stainless steels (ISO group M) and for heat‑resistant superalloys and titanium (ISO group S), offering a coating and grade tuned to cope with thermal and mechanical stresses. How does the MM5 chipbreaker benefit everyday turning operations? The MM5 chipbreaker on this Walter Tools insert promotes controlled chip formation in ductile and heat‑resistant materials, which improves operational safety, reduces manual chip clearance and supports more consistent surface finishes. Is the Trigon 80° form suitable for both roughing and finishing? Yes, the Trigon 80° geometry provides a robust cutting edge for roughing while the 0.4 mm corner radius and chip control promote acceptable surface quality in semi‑finishing tasks. Why choose Tiger·tec Silver coated grades for difficult materials? Tiger·tec Silver coatings combine thermal stability and wear resistance to protect the cutting edge under high temperatures and abrasive conditions typical of stainless steel and superalloy machining, thereby extending productive tool life. Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only; there is no affiliation between our company and the named brands. The offered item is original, brand‑new merchandise from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
WNMG060404-MP3 WPP10G WPP10G Wendeplatten - Walter Tools
Combining the Tiger‑tec Gold coating with the WPP10G grade yields a robust insert that balances wear resistance and toughness for demanding steel turning; the Trigon 80° form and 0.4 mm corner radius contribute to stable cutting and consistent surface quality. Order the WNMG060404-MP3 WPP10G directly via Metav Werkzeuge or ask our consultants if needed. WNMG060404-MP3 WPP10G Drehwendeschneidplatte for Steel — Walter Tools (Tiger‑tec Gold) A WNMG060404-MP3 WPP10G indexable turning insert engineered for reliable steel machining with a Tiger‑tec Gold coated carbide grade and an MP3 chipbreaker. Tiger‑tec Gold coated carbide MP3 chipbreaker for controlled swarf Trigon 80° for robust cutting edge 0° negative rake for stable cutting Precision for demanding steel turning The coated cemented carbide combination of Tiger‑tec Gold and the WPP10G grade is optimised for ISO P applications, delivering a balance of wear resistance and toughness suited to a broad range of steel grades. The trigon 80° geometry provides a large cutting shoulder and a robust support area at the insert seat, which contributes to reliable indexing and reduced risk of edge chipping. The 0° negative rake increases cutting edge robustness in heavier cuts, while the 0.4 mm corner radius helps to extend edge life and improve dimensional stability during serial turning operations. Controlled chip formation and consistent surface finish The MP3 chipbreaker is designed to produce predictable chip shapes and efficient evacuation in typical steel turning scenarios. Stable chip control reduces re-cutting of swarf and lowers the likelihood of surface damage, so machining runs remain productive and repeatable. As a result, operators can expect improved process stability and a more consistent surface quality from the first cut to the last, particularly on interrupted or medium-duty turning tasks. Optimised tool life and process security The Tiger‑tec Gold coating delivers thermal and abrasive protection at the cutting edge, supporting longer tool life and sustained cutting performance under industrial conditions. The WPP10G grade is a coated carbide developed for steel machining that combines resistance to wear with adequate toughness, allowing for higher reliability across varying feed and depth-of-cut regimes. This combination supports process security and reduces the frequency of tool changes, contributing to more efficient shopfloor workflows. Geometry and fit for standard toolholders With the WNMG form and size 06 paired with a thickness 04, the insert is compatible with common WNMG toolholders found in turning operations. The tolerance class M ensures consistent seating and interchangeability within tool systems, simplifying inventory management and machine setup. The compact trigon shape helps to maintain rigidity in the tool assembly, making the insert a practical choice where a strong cutting edge and compact footprint are required. Contact Metav Werkzeuge to discuss Walter Tools Tiger‑tec Gold inserts and receive tailored recommendations for the WNMG060404-MP3 WPP10G, including availability and application advice Technical Data Article number: WNMG060404-MP3-WPP10G-WALTER SKU: WNMG060404-MP3-WPP10G-WALTER Product type: Drehwendeschneidplatte Brand: Walter Tools Series: Tiger‑tec Gold Grade: WPP10G Facts Corner radius: 0.4 mm Free rake angle: 0° (negative) Insert form: Trigon 80° Size: 06 Thickness: 04 Tolerance class: M Materials & Special features Coating: Tiger‑tec Gold (coated carbide) Chipbreaker: MP3 Suitable for: Steel (ISO P) Designation: WNMG060404-MP3 Application focus: turning / indexable insert FAQ What materials is this insert suitable for? The WNMG060404-MP3 WPP10G insert is designed primarily for steel machining and is classified for ISO P applications, offering a good balance of wear resistance and toughness. What advantages does the Tiger‑tec Gold coating provide? Tiger‑tec Gold coating on the WNMG060404-MP3 WPP10G improves thermal and abrasive protection at the cutting edge, helping to extend tool life and maintain consistent cutting performance in steel turning. How does the MP3 chipbreaker affect machining? The MP3 chipbreaker promotes controlled chip formation and efficient evacuation, which reduces re-cutting of swarf and supports a more stable surface finish during turning operations on steel. Why is the Trigon 80° shape beneficial for turning? The Trigon 80° geometry provides a robust cutting edge and a large support shoulder at the insert seat, enhancing edge strength and making the insert suitable for a range of turning tasks, including interrupted cuts. What are the key dimensions and fit details for this insert? The insert is a WNMG form, size 06, thickness 04, corner radius 0.4 mm, with tolerance class M; it is intended for standard WNMG toolholders and indexable turning systems by Walter Tools. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is original factory‑new goods of the manufacturer.
WNMG060404-MP3 WPP20G G Wendeplatten - Walter Tools
Take advantage of the combination of durable Tiger·tec Gold coating, MP3 chip control and a compact Trigon 80° geometry to maintain steady metal removal rates and longer tool life; order directly via Metav Werkzeuge or ask the consultants for process data and holder recommendations. WNMG060404-MP3 WPP20G — indexable turning insert with Tiger·tec Gold coating for steel | Walter Tools WNMG060404-MP3 WPP20G is an indexable turning insert designed for general steel machining, offering robust performance for roughing and semi-finishing operations Tiger·tec Gold coating for long tool life Designed for steel machining Trigon 80° geometry for stable cuts MP3 chipbreaker for controlled chips Consistent productivity for steel turning operations The combination of Tiger·tec Gold coated carbide and the WPP20G grade delivers a balanced performance: wear resistance for longer life and enough toughness to withstand the typical temperatures of steel machining. The MP3 chipbreaker is optimised for the predictable chip formation of steels (ISO group P), reducing interruptions and easing chip evacuation. Thanks to the insert’s negative relief design, the geometry supports stable cutting forces during heavier depths of cut, which helps to increase material removal rates while maintaining tool life. Geometry and edge design for reliable machining results The Trigon 80° form and a corner radius of 0.4 mm provide a secure cutting edge that reduces chatter and helps maintain dimensional stability on turned parts. The compact size (designation 06, thickness 04) makes the insert suitable for a wide range of standard toolholders and insert seats, while the tolerance class M ensures interchangeability and repeatable clamping accuracy. These geometric characteristics contribute to predictable surface finishes and repeatable process outcomes in production environments. Process integration and economic benefits As an indexable insert from Walter Tools, this item supports quick index changes and predictable tool life, lowering downtime and overall cost per component. The coated carbide composition is aimed specifically at steels, giving favourable results across unalloyed and alloyed grades commonly encountered in workshops and production lines. The insert’s stability and chip control reduce secondary operations and improve throughput — a practical benefit for machining centres and turning lathes seeking efficiency without sacrificing reliability. For application-specific suggestions on cutting data or holder selection, Metav Werkzeuge’s technical team is available to advise. Contact Metav Werkzeuge for tailored cutting data, availability and holder compatibility for this Walter Tools turning insert — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: WNMG060404-MP3-WPP20G-WALTER Label: Drehwendeschneidplatte WNMG060404-MP3 WPP20G Walter Tools Series: Tiger-tec Gold Grade: WPP20G Core specifications Insert designation: WNMG060404-MP3 Geometry: Trigon 80° Size: 06 Thickness: 04 Corner radius: 0.4 mm Relief angle: 0° (negative) Tolerance class: M Materials and features Coating / technology: Tiger·tec Gold (coated carbide) Chipbreaker: MP3 Application group: Steel (ISO P) Execution: G FAQ What materials is this insert suitable for? The WNMG060404-MP3 WPP20G insert is developed for machining steels (ISO P); the WPP20G grade and Tiger·tec Gold coating balance wear resistance and toughness for these materials. How does the MP3 chipbreaker affect performance? The MP3 chipbreaker promotes controlled chip formation during steel turning, improving evacuation and reducing interruptions compared with inserts without dedicated chip control. Can this insert be used in standard WNMG holders? Yes, the insert follows the WNMG form and is compatible with standard toolholders designed for WNMG0604-style inserts, enabling quick indexing and repeatable seating. What is the advantage of the Trigon 80° shape? The Trigon 80° geometry offers a stable cutting edge and higher radial support, which reduces vibration and helps maintain dimensional accuracy on turned components. Does the grade WPP20G suit finishing operations? WPP20G is a universal, coated carbide grade optimised primarily for steel; it performs well in both roughing and semi-finishing depending on cutting data and machine rigidity. Hersteller: Walter AG; Tübingen; Germany. The Walter AG (brand: Walter Tools) with headquarters in Tübingen belongs to the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and product names remain the property of their respective owners. The mentioned brands are cited for clarification; there is no affiliation between our company and these manufacturers. The offered article is an original, factory-new product of the respective manufacturer.
WNMG060404-MP5 WPP10G WPP10G Wendeplatten - Walter Tools
The combination of Tiger·tec Gold coating and the WPP10G grade delivers durable performance and broad suitability for steel machining; paired with the MP5 chipbreaker and Trigon 80° geometry, this insert provides controlled chip formation and reliable clamping—order directly via Metav Werkzeuge or request technical advice from our consultants. WNMG060404-MP5 WPP10G Turning insert by Walter Tools — Tiger·tec Gold, for steel WNMG060404-MP5 WPP10G is a trigon-shaped turning insert designed for robust machining of steel, combining a coated carbide grade and an MP5 chipbreaker for productive, repeatable results Tiger·tec Gold coating for robust wear resistance Trigon 80° geometry for secure clamping MP5 chipbreaker for reliable chip control Grade WPP10G optimised for steel machining Coating and grade engineered for productivity The Tiger·tec Gold coating and the WPP10G coated-carbide grade form the technical core for long tool life and consistent performance when machining steel. This combination was developed to balance wear resistance and toughness: the coating reduces flank wear and the substrate retains edge stability under thermal and mechanical load. For production environments seeking improved process uptime, this specification reduces insert changes and supports predictable cycle times, contributing directly to lower machining costs per component. Geometry and chip control that stabilise cutting The Trigon 80° form with a 0° (negative) rake and the MP5 chipbreaker create a reliable cutting package for demanding turning operations. The trigon shape provides secure seat engagement and repeatable indexability, while the negative rake increases edge strength for interrupted or heavy cuts. The MP5 chipbreaker is optimised to generate short, segmented chips and promote consistent evacuation, which improves surface finish and reduces the risk of chip entanglement in automated setups. These design choices favour process stability and predictable component quality. Application range and practical advantages in the workshop Designed primarily for machining steel (ISO group P), this insert suits unalloyed and alloyed steels typical in general workshop and production settings. The specified corner radius of 0.4 and the plate size coded as 06 support a balance between edge robustness and the ability to achieve fine surfaces where required. The grade and geometry are set for versatile feeds and depths of cut, making this insert a practical option for both roughing and finishing sequences. Metav Werkzeuge can provide setup recommendations and cutting data to integrate the insert into existing tool cycles efficiently. For tailored technical advice on Walter Tools Tiger·tec Gold inserts or to place an order via Metav Werkzeuge, contact info@metav-werkzeuge.com or call +49 2822 7131930 for direct assistance Technical Data Article number: WNMG060404-MP5-WPP10G-WALTER Designation: WNMG060404-MP5 ISO designation: WNMG060404-MP5 WPP10G Grade: WPP10G Series: Tiger-tec Gold Manufacturer: Walter Tools Facts Plate size: 06 Plate thickness: 04 Corner radius: 0.4 Rake angle: 0° (negative) Tolerance class: M Special features Trigon 80° plate form MP5 chipbreaker Coated carbide grade Material application: steel (P) Execution: G FAQ What materials is this insert intended for? The WNMG060404-MP5 WPP10G insert is optimised for steel (ISO group P), covering unalloyed and alloyed steels commonly encountered in turning operations. What benefit does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating on the WPP10G grade enhances wear resistance and heat management, resulting in extended tool life and consistent cutting behaviour under production loads. How does the MP5 chipbreaker affect machining? The MP5 chipbreaker produces short, controllable chips and improves evacuation, which helps to maintain surface quality and reduces chip-related interruptions during automated turning. Is the insert suitable for interrupted cuts or heavy milling loads? With a 0° negative rake and a robust 0.4 corner radius, the insert offers increased edge strength suitable for interrupted cuts and more demanding turning operations. How is the product identified for ordering and tool management? Use the SKU WNMG060404-MP5-WPP10G-WALTER or the ISO designation WNMG060404-MP5 WPP10G when ordering or logging the insert in tool management systems. Walter Tools / Walter AG; Headquarters in Tübingen, Germany; www.walter-tools.com Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are used for explanation only. There is no affiliation between Metav Werkzeuge and the mentioned brands; the offered item is an original, factory-new product of the manufacturer.
WNMG060404-MP5 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of consistent chip control, robust Tiger·tec Gold coating, and straightforward geometry for reliable turning results; order genuine Walter Tools inserts through Metav Werkzeuge or consult our specialists for application advice. WNMG060404-MP5 WPP20G indexable turning insert, Tiger·tec Gold, for steel — Walter Tools The WNMG060404-MP5 WPP20G is an indexable turning insert designed for general steel machining, offering a balanced mix of wear resistance and toughness for dependable production use. Tiger·tec Gold coating for process security MP5 chipbreaker for reliable chip control Trigon 80° form for versatile turning 0.4 mm corner radius for defined cutting edge Consistent performance for machining steel The insert is built around the WPP20G coated carbide grade, optimised for machining steel (P group). The Tiger·tec Gold technology combines a wear-resistant coating with a substrate designed to tolerate typical heat and stress during steel turning, which results in longer tool life and fewer interruptions. For production environments where cycle time and repeatability matter, this combination reduces unplanned tool changes and contributes to a steadier output. Safer cycles through predictable chip control The MP5 chipbreaker geometry promotes controlled chip formation and evacuation when turning a wide range of steels. This results in reduced risk of chip entanglement and improved workpiece surface quality. In automated or semi-automated setups the stable chip behaviour lowers the likelihood of machine stoppages and makes management of coolant and chip conveyors simpler, supporting smoother upstream and downstream processes. Geometry and tolerances that simplify setup The trigon 80° form with a 0.4 mm corner radius and negative 0° clearance yields a robust cutting edge that is forgiving during insert seating and when handling interrupted cuts. Tolerance class M supports consistent seating and repeatable positioning in standard indexable toolholders, reducing the need for frequent re-measurement and adjustment. These attributes make the insert a practical choice for both batch and single-piece production where set-up time is critical. Economical machining through durability and versatility Combining a coated carbide substrate with the Tiger·tec Gold surface finish produces a cost-effective balance between wear resistance and toughness. The design targets universal turning tasks in steel, allowing fewer insert grades to cover multiple operations and thereby simplifying inventory. For manufacturers seeking predictable life and reduced tooling complexity, this insert supports higher productivity with lower management overhead. Contact Metav Werkzeuge for tailored application support and to order genuine Walter Tools Tiger·tec Gold inserts directly from stock Technical Data Article number: WNMG060404-MP5-WPP20G-WALTER Product type: Indexable turning insert Grade: WPP20G (Tiger·tec Gold) Chipbreaker: MP5 Manufacturer: Walter Tools Facts Shape: Trigon 80° Size: 06 Thickness: 04 (nominal) Corner radius: 0.4 mm Clearance: 0° (negative) Tolerance class: M Special features Coating technology: Tiger·tec Gold Substrate: Coated carbide Suitable for: Steel (P group) according to ISO 513 Application focus: General turning / versatile machining Robust edge geometry for interrupted cuts and reliable seating FAQ What materials is this insert suitable for? The insert is intended primarily for steel (P group) applications; the WPP20G grade and Tiger·tec Gold coating are tuned for unalloyed and alloyed steels. How does the MP5 chipbreaker influence machining? The MP5 chipbreaker promotes short, controllable chips in a wide range of steel turning operations, improving chip evacuation and surface finish while reducing machine interruptions. Is the 0.4 mm corner radius suitable for finishing? A 0.4 mm corner radius provides a defined cutting edge that balances strength and finish capability; it is suitable for many semi-finishing tasks and offers robustness for light finishing when used with appropriate cutting parameters. Can this insert be used in interrupted cutting or heavy cuts? The trigon 80° form and negative 0° clearance, combined with the coated carbide construction, make the insert capable of handling interrupted cuts and moderate heavy-duty operations with stable edge performance. Which toolholders fit this insert designation? Standard indexable turning toolholders compatible with the WNMG insert family accept this geometry; correct seating per the holder manufacturer's recommendations ensures repeatable performance. Hersteller: Walter Tools — Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners and are mentioned solely for explanatory purposes. There is no association between our company and the referenced brands. The offered item is an original, factory-new product of the manufacturer.
WNMG060404-MP5 WPP30G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating, the MP5 chipbreaker and robust trigon 80° geometry to achieve stable, productive turning of steel; order the genuine insert directly via Metav Werkzeuge or request consultancy for process adaptation. WNMG060404-MP5 WPP30G Indexable Turning Insert – Tiger·tec Gold coated carbide, MP5 chipbreaker by Walter Tools The WNMG060404-MP5 WPP30G is an indexable turning insert intended for steel machining, combining a wear-resistant Tiger·tec Gold coating with an MP5 chipbreaker and trigon geometry for reliable metal removal. Tiger·tec Gold coated carbide grade WPP30G MP5 chipbreaker for stable chip control Trigon 80° geometry for robust turning 0° negative rake with 0.4 mm corner radius High-performance coating engineered for efficient steel turning The Tiger·tec Gold coating together with the WPP30G grade provides improved wear resistance and consistent cutting performance when machining steel. As a coated carbide insert, the surface treatment reduces adhesion and thermal wear, which translates into longer edge life and fewer tool changes. This makes the solution particularly economical for medium- to high-volume production where tool life and process stability influence throughput. Explanation: coated carbide combines a hard substrate with thin, engineered layers that protect the cutting edge against heat and abrasion while maintaining fracture resistance. Stable chip control and a geometry that improves productivity The MP5 chipbreaker has been designed to generate short, manageable chips during steel turning, reducing the risk of entanglement and improving surface finish. The trigon 80° configuration increases cutting-edge strength and allows secure clamping in standard toolholders, while the 0° negative rake enhances edge robustness under interrupted cuts or heavy depth of cut. The 0.4 mm corner radius contributes to smooth cutting action and improved part finish without compromising edge strength. Together these characteristics support higher metal removal rates and more consistent cycle times in industrial turning operations. Practical integration, tolerance class and workshop advantages The insert’s dimensional designation and tolerance class M ensure repeatable positioning in toolholders and predictable tool offsets, simplifying setup and tool management. The size and thickness codes correspond to industry standards for indexable inserts, aiding quick selection across tool inventories. Intended users include manufacturers, job shops and maintenance departments seeking a balance of tool life and process reliability when machining unalloyed and alloyed steels. If application-matched data are required, Metav Werkzeuge can provide cutting parameters and compatibility guidance to align the insert’s properties with specific machining strategies. Contact Metav Werkzeuge for an application assessment or to request a quote for genuine Walter Tools Tiger·tec Gold inserts and tailored cutting-data recommendations Technical data SKU: WNMG060404-MP5-WPP30G-WALTER Designation: WNMG060404-MP5 WPP30G Manufacturer: Walter Tools Facts Insert size: 06 Thickness: 04 Corner radius: 0.4 mm Relief angle: 0° (negative) Shape: Trigon 80° Tolerance class: M Special features Series: Tiger·tec Gold Grade: WPP30G (coated carbide) Chipbreaker: MP5 Material application: Steel (P) FAQ What materials is this insert suited for? The WNMG060404-MP5 WPP30G is specified for machining steel materials (ISO group P) and is optimised for the heat and chip formation typical of steel turning. How does the MP5 chipbreaker affect surface finish? The MP5 chipbreaker promotes short, controlled chips which reduce built-up edge and help achieve a consistent surface finish when combined with the insert’s trigon geometry. Is this insert compatible with standard WNMG toolholders? The trigon 80° form and the designation align with standard WNMG toolholder interfaces, enabling straightforward replacement and secure clamping in compatible holders. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand Walter Tools) with headquarters in Tübingen is one of the leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names are used here for explanation only. The offered item is an original, brand-new product from the manufacturer.
WNMG060408-FM5 WMP20G WMP20G Wendeplatten - Walter Tools
Take advantage of the proven combination of Walter Tools' Tiger‑tec Gold grade and a robust Trigon 80° geometry for reliable machining of stainless steel; order directly via Metav Werkzeuge or request tailored advice from our consultants. WNMG060408-FM5 WMP20G — Walter Tools indexable turning insert with Tiger‑tec Gold coating for stainless steel WNMG060408-FM5 WMP20G is a negative‑rake, trigon‑shaped insert designed for turning operations on stainless steel under medium to robust cutting conditions Tiger‑tec Gold coated grade WMP20G Trigon 80° geometry for stable cutting FM5 chipbreaker for controlled chip flow 0.8 mm corner radius for edge strength High process stability and longer tool life through advanced coating The combination of the Tiger‑tec Gold technology with the WMP20G coated carbide provides significantly improved wear resistance and thermal stability compared with uncoated grades. This coating reduces adhesion and protects the cutting edge during interrupted cuts and heavy feeds, which leads to stable chip formation and extended tool life. For operations on stainless steel the grade supports safer machining by lowering the tendency for built‑up edge and reducing unscheduled tool changes, improving uptime and repeatability in production. Geometry and chip control engineered for robust turning The Trigon 80° insert form with a 0.8 mm corner radius and FM5 chipbreaker gives a balance between edge strength and surface finish. The negative 0° rake delivers a rugged cutting edge suitable for medium to robust cuts and helps maintain dimensional stability when machining tougher grades. The FM5 chipbreaker is designed to guide chips reliably away from the cutting zone, reducing the risk of re‑cutting and supporting consistent surface quality on stainless steel components. Practical application advice for reliable results As an indexable turning solution, this insert excels in operations where secure clamping and steady feed are prioritised. The WMP20G grade is tailored for stainless steel (ISO group M) and performs best with moderate to conservatively increased cutting speeds depending on material condition and machine rigidity. For users less familiar with cutting grades: the M designation denotes suitability for stainless steels that typically produce high heat and tend toward ductile chip formation; using a coated, robust insert reduces workhardening and improves cycle stability. For machining tasks that demand process reliability and enhanced tool life, consider Walter Tools' WNMG060408-FM5 WMP20G from Metav Werkzeuge — contact Metav Werkzeuge for application‑specific recommendations at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data SKU: WNMG060408-FM5-WMP20G-WALTER Designation: WNMG060408-FM5 WMP20G Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WMP20G Product type: Indexable turning insert (drehwendeschneidplatte) Core figures Insert form: Trigon 80° Corner radius: 0.8 mm Insert size: 06 Thickness: 04 Rake angle: 0° (negative) Chipbreaker: FM5 Tolerance class: M Special features Coating technology: Tiger‑tec Gold (coated carbide) Material group suitability: M (stainless steel) Robust geometry for medium to robust cutting conditions Designed for stable chip formation and improved edge life Manufacturer brand: Walter Tools FAQ What materials is this insert suitable for? The WNMG060408-FM5 WMP20G insert is specified for machining stainless steel (ISO group M); the WMP20G grade supports secure chip formation and edge stability on these materials. How does the Tiger‑tec Gold coating benefit production? Tiger‑tec Gold on the WMP20G grade increases thermal resistance and wear protection, extending insert life and improving process consistency during turning operations. Which insert geometry suits interrupted cuts? The Trigon 80° form with a 0.8 mm corner radius and negative 0° rake offers enhanced edge strength, making the insert appropriate for interrupted cuts and heavier feed conditions. Can the insert provide a good surface finish on stainless steel? Yes; the FM5 chipbreaker and stable edge retention of the WMP20G grade help achieve consistent surface quality while maintaining secure chip control. Is this insert compatible with standard toolholders for WNMG inserts? The WNMG‑type form corresponds to common toolholder interfaces for trigon inserts; confirm holder compatibility and clamping condition before use to ensure optimal performance. Die Walter AG (marketed as Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names and trademarks are cited for explanatory purposes only; there is no affiliation between our company and the mentioned brands. The offered article is an original, factory‑new product of the manufacturer.
WNMG060408-FM5 WSM10S WSM10S Wendeplatten - Walter Tools
Taking advantage of the combination of a robust Tiger·tec Silver grade, a Trigon 80° geometry with a 0.8 mm corner radius, and a reliable FM5 chipbreaker results in stable cutting edges and consistent chip control for demanding stainless and high-temperature alloy applications; order via Metav Werkzeuge or request technical advice from our consultants. WNMG060408-FM5 WSM10S Walter Tools — Trigon 80° turning indexable insert with Tiger·tec Silver grade WNMG060408-FM5 WSM10S is an indexable turning insert designed for heavy-duty machining of stainless steels and heat-resistant alloys, combining a coated carbide grade with a Trigon 80° form for robust edge stability Tiger·tec Silver grade for long tool life Trigon 80° geometry for secure cutting edge FM5 chipbreaker for controlled chip formation 0.8 mm corner radius for durable finishing edges High-performance grade engineered for difficult-to-machine materials The WSM10S grade from Walter Tools, part of the Tiger·tec Silver series, is a coated carbide formulation developed for applications in stainless steels and superalloys. Its coating system and substrate balance thermal resistance and wear resistance, so edge life is extended under high temperatures. The result is fewer tool changes and lower process interruptions, which contributes directly to predictable production output. For shops processing a mix of austenitic stainless steels or heat‑resistant nickel alloys, this grade supports consistent chip formation and reduced risk of built-up edge. Geometry tailored to secure chip control and stable cutting The Trigon 80° shape combined with a 0° relief (negative) rake and the FM5 chipbreaker provides a reliable cutting profile that resists edge chipping. The 0.8 mm corner radius increases edge strength, making the insert suitable for operations where slight robustness is required without compromising surface quality. The FM5 chipbreaker is designed to split and curl chips in interrupted or continuous cuts, improving evacuation and protecting the workpiece finish. These geometric choices reduce vibration and help maintain dimensional stability across longer tool life. Productivity advantages and process reliability Using this insert supports higher uptime through its balanced substrate and coating combination. The coated carbide construction is optimised for heat management and abrasion resistance, which improves wear characteristics during continuous production runs. As a consequence, cycle times are kept more consistent and regrinding or index changes are reduced, delivering tangible economic benefits in medium to large batch environments. The overall package emphasises repeatable results, consistent surface finish and predictable maintenance intervals. Practical application guidance for setup and use The insert is applicable to ISO material groups M (stainless steels) and S (heat-resistant superalloys and titanium), offering versatility across demanding alloys. For best results, employ a rigid toolholder and stable clamping to leverage the Trigon form and corner radius; coolant strategy should be matched to the workpiece and cutting parameters to control temperature and chip flow. The insert suits roughing to semi-finishing depending on the chosen feed and depth of cut, and toolpaths should be planned to avoid excessive shock in interrupted cuts. Where process security is paramount, pairing the insert with a holder that supports indexable corners will maximise productivity and edge life. For detailed availability and tailored machining parameters with Walter Tools' Tiger·tec Silver grade inserts, contact Metav Werkzeuge for stock information and application support at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: WNMG060408-FM5-WSM10S-WALTER Product type: Turning indexable insert Full designation: WNMG060408-FM5 WSM10S Manufacturer: Walter Tools Facts Insert size: 06 Thickness code: 04 Shape: Trigon 80° Relief angle: 0° (negative) Corner radius: 0.8 mm Tolerance class: M Special features Grade series: Tiger·tec Silver Grade/sort: WSM10S Chipbreaker: FM5 Material classes: S / M Coated carbide substrate FAQ What materials is this insert suitable for? The WNMG060408-FM5 WSM10S insert is designed primarily for stainless steels (M) and heat-resistant superalloys/titanium (S), offering secure chip control and thermal stability. How does the FM5 chipbreaker affect machining? The FM5 chipbreaker promotes controlled chip formation and evacuation, reducing the risk of entanglement and improving surface finish when using the Walter Tools Trigon geometry. Is the insert suitable for interrupted cuts? Yes; the Trigon 80° form and a 0.8 mm corner radius deliver enhanced edge strength, making the insert more resistant to shock in interrupted or semi‑roughing operations. Can this insert be used for finishing passes? Depending on the selected feeds and depths, the coated carbide grade supports semi‑finishing and finishing; the geometry balances edge strength with acceptable surface quality. Which holders are recommended for optimal performance? Rigid, correctly dimensioned turning holders that accommodate the WNMG Trigon form ensure stable clamping and full utilisation of the Walter Tools grade characteristics. Manufacturer / Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen The Walter AG (brand presentation: Walter Tools), headquartered in Tübingen, is one of the world's leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The item offered is original, brand‑new goods from the manufacturer.
WNMG060408-FM5 WSM20S WSM20S Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Silver coating, FM5 chip control and the Trigon 80° geometry for durable cutting edges and consistent chip formation; order the insert directly via Metav Werkzeuge or consult our specialists for process matching. WNMG060408-FM5 WSM20S – Trigon 80° turning insert with Tiger·tec Silver coating (Walter Tools) The WNMG060408-FM5 WSM20S is a Trigon 80° turning insert designed for heavy-duty finishes and secure performance in demanding materials such as rostfreier Stahl and heat‑resistant superalloys. Tiger·tec Silver coating for high process security Trigon 80° form for stable edge support FM5 chipbreaker for reliable chip control Suitable for rostfreier Stahl and superalloys Consistent performance through specialised coating and grade The coating technology Tiger·tec Silver combines a wear-resistant surface with optimised substrate properties to extend tool life under thermal and mechanical stress. As a coated carbide grade, the insert promotes predictable wear behaviour and reduced edge build-up when machining high-temperature alloys. This leads to longer intervals between index changes, lower tooling costs per component and fewer unplanned interventions in production. The combination of coating and substrate is aimed at operators seeking stable, repeatable results in series production. Geometry engineered for secure cutting and chip management The Trigon 80° form, paired with a 0° (negative) rake and a 0.8 mm corner radius, is designed to support the cutting edge under heavier feed and interrupted cuts. The FM5 chipbreaker ensures controlled chip formation, which reduces the risk of chip-related damage and simplifies chip evacuation. Together these features deliver enhanced edge security and make the insert suitable for tougher turning operations where dimensional stability and surface finish are priorities. Broad material capability with focus on challenging alloys The insert’s grade WSM20S is tailored for machining applications classified under ISO groups M and S: M for rostfreier Stahl and S for heat‑resistant superalloys and titanium. The grade’s heat resistance and edge stability help to manage the poor thermal conductivity and work‑hardening tendencies of these materials. In practice, this means fewer tool changes on demanding workpieces and improved component consistency when turning complex alloys that would otherwise shorten tool life. Productivity and shop-floor integration Specified as a WNMG‑format insert with standard dimensions and a moderate thickness, this product is compatible with conventional WNMG holders and facilitates straightforward integration into existing turning cells. The robust edge geometry and coating synergy reduce unplanned downtime and support higher metal removal rates without sacrificing surface quality. For procurement and process planning, the insert’s design promotes stock rationalisation and repeatable performance across batches, strengthening throughput while maintaining quality standards. Contact Metav Werkzeuge for tailored application advice and fast supply of Walter Tools Tiger·tec Silver inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: WNMG060408-FM5-WSM20S-WALTER Designation: WNMG060408-FM5 WSM20S Manufacturer: Walter Tools Product type: Drehwendeschneidplatte Grade/series: WSM20S / Tiger·tec Silver Numbers / Core technical data Plate size: 06 Plate thickness: 04 Corner radius: 0.8 mm Relief angle: 0° (negative) Plate form: Trigon 80° Tolerance class: M Special features Coating: Tiger·tec Silver (coated carbide) Chipbreaker: FM5 Material application: S / M (superalloys, rostfreier Stahl) Execution: G SKU: WNMG060408-FM5-WSM20S-WALTER FAQ Is this insert suitable for rostfreier Stahl? Yes. The WNMG060408-FM5 WSM20S is specifically formulated for rostfreier Stahl (ISO group M) and provides stable cutting behaviour and reduced edge build-up when machining these materials. What advantage does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating on this Walter Tools insert improves heat resistance and wear behaviour, resulting in more consistent tool life and better performance in thermally aggressive turning operations. How does the FM5 chipbreaker affect machining? The FM5 chipbreaker promotes predictable chip formation and evacuation, which decreases the risk of chip entanglement and supports reliable surface quality during turning. Can the insert handle titanium or high-temperature alloys? Yes. The WSM20S grade is intended for demanding materials within ISO group S, offering the thermal and edge stability required for many heat‑resistant alloys and titanium work. Does the Trigon 80° form offer any operational benefits? The Trigon 80° geometry provides strong edge support and good access for finishing and semi-finishing cuts, improving dimensional stability in heavy or interrupted turning. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanation only. There is no affiliation between our company and the named brands. The offered item is an original, factory-new product of the manufacturer Walter Tools.
WNMG060408-FP5 WKP01G WKP01G Wendeplatten - Walter Tools
Take advantage of a high-performance, coated carbide grade that combines Tiger·tec Gold wear resistance with a stable Trigon 80° geometry for consistent chip control and reduced tool changes; order the insert via Metav Werkzeuge or consult our specialists for cutting data and application advice. WNMG060408-FP5 WKP01G indexable turning insert, Tiger·tec Gold coating — Walter Tools The WNMG060408-FP5 WKP01G is an indexable turning insert engineered for productive turning of steel and cast iron, offering a balance of wear resistance and stable geometry for both roughing and finishing operations. Tiger·tec Gold coated carbide for extended life Trigon 80° geometry for stable cutting 0.8 mm corner radius for consistent surface finish FP5 chipbreaker tuned for general turning Negative 0° rake for secure insert seating Longer productive life through advanced coating technology The combination of Tiger·tec Gold and coated carbide provides a marked improvement in wear resistance compared with uncoated grades, leading to longer tool life and fewer indexings in high-volume turning. The advanced multi-layer coating reduces abrasive wear and improves thermal resilience, which directly benefits cycle times and tool-change intervals. For production environments where uptime and repeatability matter, this grade delivers a measurable reduction in operating cost per part while maintaining stable edge condition under varied cutting speeds. Stable geometry for predictable machining results The Trigon 80° form with a 0.8 mm corner radius and negative 0° rake ensures secure clamping and robust cutting edge support, which translates into consistent surface quality and reduced vibration. The FP5 chipbreaker design promotes controllable chip formation across a range of feeds, helping to avoid built-up edge and erratic chip behaviour when machining mixed batches. These geometric choices make the insert particularly suitable where process stability and reproducible part quality are essential outcomes. Wide applicability across steel and cast iron work This grade is specified for ISO groups P (steel) and K (cast iron), so it is suitable for many common shop tasks from general turning of alloyed steels to cast-iron components. The cutting-material compatibility results from the coating and substrate combination that balances toughness and hardness to manage both ductile and brittle chip types. In practice, this versatility reduces tool inventory complexity: one insert family can service multiple workpiece materials while retaining predictable performance. Manufactured tolerances and dimensions for precise set-up With a medium tolerance class (M), plate size designation 06 and thickness 04, the insert fits standard toolholders designed for WNMG inserts and provides consistent seat repeatability. Consistent geometry and tolerance support reliable tool life forecasting and quality control in production. Integrating this insert into a machining cell simplifies process documentation and enables straightforward replacement strategies without extensive readjustment after index changes. Contact Metav Werkzeuge for tailored application recommendations on Walter Tools Tiger·tec Gold inserts and request cutting data specific to the WNMG060408-FP5 WKP01G SKU. Technical data Article number: WNMG060408-FP5-WKP01G-WALTER Product designation: WNMG060408-FP5 WKP01G Product type: Indexable turning insert Manufacturer: Walter Tools Facts Corner radius: 0.8 mm Free angle (rake): 0° (negative) Plate size: 06 Plate thickness: 04 Tolerance class: M Special features Coating: Tiger·tec Gold Grade / substrate: Coated carbide Chipbreaker: FP5 Geometry: Trigon 80° Series: Tiger-tec Gold Sort: WKP01G Execution: G Material application: Steel (P) Material application: Cast iron (K) FAQ Is this insert suitable for both roughing and finishing? The WNMG060408-FP5 WKP01G from Walter Tools is designed for flexible use; its FP5 chipbreaker and 0.8 mm corner radius offer a compromise between material removal rate and surface finish, making it appropriate for light roughing and finishing tasks depending on cutting parameters. Which workpiece materials are recommended for this grade? This insert is specified for ISO groups P and K, so it is recommended for machining various steels and cast irons with the WNMG060408-FP5 WKP01G grade, benefiting from the Tiger·tec Gold coating’s wear resistance. How does the Trigon 80° geometry affect toolholding and cutting forces? The Trigon 80° shape provides a solid seat and good edge support, reducing vibration and improving cutting stability; this geometry helps maintain consistent cutting forces and enhances reproducibility when using the WNMG060408-FP5 WKP01G in standard WNMG toolholders. What does the tolerance class M imply for set-up precision? Tolerance class M denotes medium manufacturing tolerances that balance economical production with reliable repeatability, enabling straightforward insert changes with minimal rework in jigs and toolholders for the WNMG060408-FP5 WKP01G. Can this insert cope with higher cutting speeds? The coated carbide substrate combined with Tiger·tec Gold enhances thermal resistance and wear performance, which supports elevated cutting speeds within the manufacturer’s recommended parameters for the WNMG060408-FP5 WKP01G. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
WNMG060408-FP5 WPP10G Wendeplatten - Walter Tools
Combine the Tiger·tec Gold coating with a robust trigon 80° geometry and the FP5 chipbreaker for reliable steel turning; order the insert directly via Metav Werkzeuge or consult our specialists for tailored application advice. WNMG060408-FP5 WPP10G — Indexable turning insert, Tiger·tec Gold grade by Walter Tools The WNMG060408-FP5 WPP10G is a trigon 80° indexable insert designed for efficient machining of steel under ISO P conditions, offering a balanced mix of wear resistance and chip control. Tiger·tec Gold coating for long tool life Suitable for steel machining (ISO P) Trigon 80° insert with 0.8 mm nose radius Negative 0° rake for secure edge performance Consistent performance through advanced coating and grade The coated WPP10G grade, part of the Tiger·tec Gold series, is formulated for high wear resistance and predictable flank behaviour when machining steels. The combination of a modern CVD/PVD-style coating and a wear-resistant substrate results in extended component life and fewer indexings, which supports uninterrupted production cycles. The FP5 chipbreaker is tuned to the thermal and chip-forming characteristics of steel (ISO P), so chip flow is stabilised and the risk of built-up edge is reduced. These technical measures translate directly into lower tooling costs per part and improved process reliability. Geometry engineered for stable cutting and surface quality The trigon 80° form and a 0.8 mm nose radius provide a strong cutting edge that tolerates moderate interruptions and stiff cutting conditions. The insert’s negative 0° rake promotes a robust edge and reduces the tendency for edge chipping in heavier cuts, while the compact plate thickness supports stable clamping in matched toolholders. Together, these geometry choices enhance dimensional consistency and help achieve repeatable surface finishes in serial production. For users less familiar with insert geometry: a trigon profile offers more edge strength than finer shapes while still enabling acceptable finishing results when set up with appropriate feeds. Practical integration and machining guidance for workshops This indexable insert is suited to standard turning toolholders that accept WNMG-style clamping; it performs well across a broad range of steel grades thanks to its tailored grade and chipbreaker. When implemented in production, the insert’s stability reduces secondary operations caused by poor surface quality, and the reliable wear behaviour simplifies inventory planning. For shops seeking optimisation, Metav Werkzeuge’s technical advisors can recommend matching holder types and cutting-parameter windows to exploit the Tiger·tec Gold benefits fully. The net result is an efficient workflow, lower scrap rates and fewer unplanned tool changes. For reliable steel turning with Walter Tools’ Tiger·tec Gold grade and the WNMG060408-FP5 configuration, contact Metav Werkzeuge for application support and prompt supply at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: WNMG060408-FP5-WPP10G-WALTER Designation: WNMG060408-FP5 WPP10G Manufacturer: Walter Tools Data Size: 06 Thickness: 04 Corner radius: 0.8 mm Clearance / rake: 0° (negative) Tolerance class: M Special features Grade: WPP10G (Tiger·tec Gold) Chipbreaker: FP5 Shape: Trigon 80° Material application: Steel (ISO P) Series: Tiger·tec Gold FAQ What materials is this insert suitable for? The WNMG060408-FP5 WPP10G is optimised for machining steel (ISO P), with the Tiger·tec Gold grade tuned to typical heat and chip-formation in steels. How does the FP5 chipbreaker affect machining? The FP5 chipbreaker promotes controlled chip formation in steel, improving evacuation and reducing the risk of built-up edge when using the WPP10G grade. Can the trigon 80° form be used for finishing? Yes, the trigon 80° geometry offers a strong cutting edge that can achieve good surface quality; choosing a suitable nose radius and feed will balance edge strength and finish. What does a negative 0° rake mean for operation? A negative 0° rake provides a robust cutting edge that resists chipping under interrupted cuts and heavy engagement, increasing process security in demanding operations. Is this insert compatible with standard WNMG toolholders? The insert follows the WNMG specification and is compatible with toolholders designed for WNMG inserts; correct clamping and seat condition remain essential for performance. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only and do not imply any affiliation between our company and the named brands. The offered item is original, brand-new merchandise from the manufacturer.
WNMG060408-FP5 WPP20G G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, a robust WPP20G carbide grade and the Trigon 80° form for consistent steel turning and long tool life; order via Metav Werkzeuge or consult our application specialists for tailored cutting data. WNMG060408-FP5 WPP20G – Trigon 80° coated carbide insert by Walter Tools A WNMG060408-FP5 WPP20G indexable turning insert designed for reliable ISO P (steel) machining with a Tiger·tec Gold coated carbide grade and FP5 chipbreaker. Tiger·tec Gold coated carbide grade WPP20G Trigon 80° geometry for secure clamping Chipbreaker FP5 for controlled chip formation Corner radius 0.8 mm, negative 0° geometry High, consistent performance for steel turning The coated carbide grade and Tiger·tec Gold technology deliver a balance of wear resistance and toughness tailored for steel machining (ISO P). The insert’s coating reduces flank wear and maintains edge stability at elevated cutting temperatures, which translates into predictable tool life and stable part quality. For production runs where consistency matters, this geometry supports repeatable results and reduces interruptions caused by premature edge failure. Geometry that improves process security and surface finish The Trigon 80° form combined with a 0.8 mm corner radius and a negative 0° relief angle provides a sturdy cutting edge that resists chipping under intermittent cuts. The FP5 chipbreaker promotes manageable chip shapes when turning unalloyed and alloyed steels, lowering the risk of built-up edge and improving surface finish. In practical terms, machine set-up becomes simpler and cutting parameters can be applied with greater confidence. Efficient material coverage and application guidance The WPP20G grade is optimised for the demands of steel turning, offering a versatile compromise between hardness and toughness to cover a wide range of steel grades. This insert is suited for routine medium to heavy turning operations where stability and reproducible performance are required. When selecting cutting data, begin with conservative depth of cut and feed values and adjust upwards while monitoring tool wear to find the optimal productivity window. Benefits for workshop productivity and handling Using an indexable insert in Trigon form reduces tool change times and inventory complexity compared with solid tools. The negative geometry ensures secure seating in standard toolholders and supports higher cutting forces, enabling more productive material removal rates. Combined with the branded grade and chip control, the insert supports efficient, predictable machining cycles and lower process variability. For application-specific recommendations or to secure supply of Walter Tools inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the best grade and machining data for the intended steel grade. Technical data Article number: WNMG060408-FP5-WPP20G-WALTER Designation: WNMG060408-FP5 WPP20G Series: Tiger-tec Gold Grade: WPP20G Manufacturer: Walter Tools Execution: G Facts Plate form: Trigon 80° Plate size: 06 Thickness: 04 Corner radius: 0.8 mm Relief angle: 0° (negative) Tolerance class: M Special features Coating technology: Tiger·tec Gold Material family: Coated carbide Chipbreaker: FP5 Suitable for: Steel (ISO P) Geometry: Negative insert, trigon shape Sort description: WPP20G — coated carbide for steel machining FAQ What steel grades is this insert suitable for? The WNMG060408-FP5 WPP20G insert is specified for ISO P steels, covering unalloyed and alloyed steels where a balanced wear resistance and toughness are required. How does the FP5 chipbreaker influence machining? The FP5 chipbreaker on this Walter Tools insert controls chip formation to reduce entangling and improve evacuation, helping to maintain surface quality during turning. Which toolholders are compatible with the Trigon 80° form? Standard indexable turning holders accepting WNMG trigon inserts are compatible; the negative geometry requires secure clamping to exploit the insert’s cutting stability. How should cutting data be adjusted for longer tool life? Start with conservative feeds and depths of cut and increase gradually while monitoring wear; the Tiger·tec Gold coating supports higher temperatures, but gradual optimisation yields best process security. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Walter AG (brand: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and product names are the property of their respective owners and are mentioned for explanatory purposes only; no affiliation with our company is implied. The offered item is an original, factory-new product of the manufacturer.
WNMG060408-FW5 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of long tool life and controlled chip evacuation for steady, productive turning of steel components. The combination of Tiger·tec Gold coating and an FW5 chipbreaker provides wear resistance and reliable surface quality; order the insert via Metav Werkzeuge or consult our specialists for process recommendations. WNMG060408-FW5 WPP10G — Indexable Turning Insert, Trigon 80°, Tiger·tec Gold (Walter Tools) for Steel The WNMG060408-FW5 WPP10G is a trigon 80° indexable turning insert designed for versatile steel turning operations, offering a coated carbide grade optimised for stable chip formation. Tiger·tec Gold coating for long tool life Trigon 80° geometry for versatile turning FW5 chipbreaker for controlled chip flow Optimised for steel machining (ISO P) Increased tool life through advanced coating technology The combination of the Tiger·tec Gold coating and the WPP10G grade delivers enhanced wear resistance under the thermal and mechanical stresses typical of steel turning. The multi-layer coating reduces flank wear and increases edge stability, which contributes to longer service intervals and fewer insert changes. For production environments this translates into improved uptime and more predictable tool consumption. The coated carbide construction also supports higher cutting speeds where process parameters allow, helping to maintain consistent part quality across batches. Geometry and chip control for reliable surface finish The Trigon 80° shape and FW5 chipbreaker are designed to balance strength and chip formation: the three-edged geometry provides a robust cutting edge, while the specially profiled chipbreaker promotes controlled chip flow for common turning strategies. The insert features a 0° negative rake that increases edge support and cutting stability, and a 0.8 mm corner radius that helps achieve a good surface finish without compromising tool life. These characteristics make the insert well suited to medium to heavy finishing cuts where process security and repeatability are priorities. Application range and process benefits for steel components Assigned to ISO group P, this insert is intended primarily for the machining of unalloyed and alloyed steel grades. The WPP10G carbide grade provides a balanced combination of wear resistance and toughness, suitable for a broad range of steel workpieces. Typical benefits include reduced tool change frequency, consistent dimensional results, and simplified tool inventory thanks to the insert’s universal turning capability. The tolerance class M supports stable fitting and repeatable assembly into standard toolholders, ensuring predictable performance on turning lathes and CNC machines. Choose Walter Tools Tiger·tec Gold inserts like the WNMG060408-FW5 WPP10G for robust steel turning; contact Metav Werkzeuge for availability and process advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: WNMG060408-FW5-WPP10G-WALTER Label: Drehwendeschneidplatte WNMG060408-FW5 WPP10G Walter Tools Product type: Indexable turning insert Core specifications Plate size: 06 Thickness: 04 Corner radius: 0.8 mm Relief angle: 0° (negative) Geometry: Trigon 80° Chipbreaker: FW5 Tolerance class: M Materials & special features Coating / grade: Tiger·tec Gold, WPP10G (coated carbide) Application group: P (steel) Series: Tiger-tec Gold Manufacturer: Walter Tools FAQ Which materials is this insert suitable for? This insert is specified for ISO group P and is suitable for machining various steel grades; the WPP10G grade is optimised for the thermal and chip formation characteristics of steel. What are the main advantages of the Tiger·tec Gold coating? The Tiger·tec Gold coating on the WNMG060408-FW5 WPP10G enhances wear resistance and edge stability, supporting longer tool life and consistent surface quality when turning steel components. How does the FW5 chipbreaker affect machining? The FW5 chipbreaker promotes controlled chip evacuation and stable chip shapes during turning, which helps maintain process security and reduces the risk of chip-related interruptions. Is the geometry suitable for finishing or roughing operations? The Trigon 80° geometry with a 0.8 mm corner radius provides a good compromise between strength and surface finish, making the insert suitable for finishing and medium cutting operations rather than heavy roughing. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered article is an original, factory-new product of the manufacturer.
WNMG060408-FW5 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating, robust FW5 chip control and trigon geometry for stable, productive turning of steel; order the insert directly via Metav Werkzeuge or consult our technical advisers for application support. WNMG060408-FW5 WPP20G turning insert — Tiger‑tec Gold, FW5 chipbreaker by Walter Tools The WNMG060408-FW5 WPP20G is a trigon 80° indexable turning insert designed for general steel machining, offering a coated cemented carbide grade optimised for heat and chip formation in steel cutting. Tiger‑tec Gold coating for robust edge Optimised FW5 chipbreaker for steel Trigon 80° geometry with 0.8 mm radius Negative 0° rake for increased stability High‑performance coating for demanding steel operations The Tiger‑tec Gold series delivers a coated cemented carbide composition engineered for the thermal and mechanical conditions of steel cutting. The WPP20G grade combines wear resistance with a level of toughness that suits a wide range of steels according to ISO group P, supporting both continuous and interrupted cuts. Thanks to the Tiger‑tec Gold surface treatment, flank wear progression is slowed and edge stability is improved, which translates into longer tool life and fewer insert changes per batch. This technical advantage reduces process interruptions and contributes to a more consistent part quality across production runs. Precision geometry and dependable chip control The trigon 80° form and FW5 chipbreaker are matched to provide secure cutting engagement and effective chip segmentation when machining steel. The negative 0° rake increases cutting edge support and minimises vibration in heavy‑cut situations, while the 0.8 mm corner radius provides a balance between edge strength and achievable surface finish. These geometric choices mean the insert offers predictable cutting forces and better dimensional stability on turned components, particularly when facing varying stock conditions or intermittent cuts common in workshop and production environments. Productivity gains through reproducibility and process security Adopting this insert supports measurable productivity improvements: fewer stoppages for tooling adjustments, consistent surface finishes and repeatable tool life across similar batch sizes. The combination of grade and geometry promotes stable chip formation and reduces the risk of unexpected edge breakdown, delivering higher first‑pass yields and lower rework rates. For operations seeking a practical, ready‑to‑use solution for steel turning, the insert integrates into standard toolholding systems and complements Walter Tools’ commitment to reliable machining outcomes and predictable performance. Contact Metav Werkzeuge for tailored machining advice and rapid supply of Walter Tools Tiger‑tec Gold inserts; technical consultants are available at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: WNMG060408-FW5-WPP20G-WALTER Article: WNMG060408-FW5 WPP20G Type: turning insert Grade: WPP20G Brand: Walter Tools Series: Tiger‑tec Gold Core specifications Shape: Trigon 80° Corner radius: 0.8 mm Rake angle: 0° (negative) Chipbreaker: FW5 Size code: 06 Thickness code: 04 Tolerance class: M Materials & applications Applicable material group: Steel (ISO P) Coating: Tiger‑tec Gold (coated cemented carbide) Designed for: stable chip formation and heat management in steel machining FAQ What steels is this insert designed for? The WNMG060408-FW5 WPP20G is specified for ISO group P materials, covering unalloyed and alloyed steels where controlled heat and chip formation are required. How does the FW5 chipbreaker affect machining performance? The FW5 chipbreaker is optimised for steel to provide reliable chip segmentation and evacuation, improving process stability during turning operations. Can the insert be used for heavy interrupted cuts? Yes, the trigon 80° form with a 0° negative rake and 0.8 mm corner radius increases edge support and helps withstand intermittent loading typical of interrupted cuts. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
WNMG060408-FW5 WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating, the WSM20S grade and the Trigon 80° geometry for stable cutting in demanding materials; order directly via Metav Werkzeuge or consult our specialists for application-specific recommendations. WNMG060408-FW5 WSM20S — Trigon 80° turning insert, Tiger‑tec Silver (Walter Tools) The WNMG060408-FW5 WSM20S is a negative‑rake trigon turning insert designed for robust machining of rostfreier Stahl and heat‑resistant superalloys. Tiger‑tec Silver coated carbide grade WSM20S Trigon 80° insert with 0° negative rake FW5 chipbreaker for secure chip control Optimised for rostfreier Stahl and superalloys Reliable cutting performance in difficult materials The coated carbide WSM20S grade, part of the Tiger‑tec Silver series, is engineered for machining tough workpiece groups such as rostfreier Stahl and heat‑resistant superalloys. The combination of coating technology and substrate hardness ensures consistent edge stability under thermal and mechanical load. For production environments where chip formation and tool life directly affect throughput, this insert delivers measurable improvements in process reliability and reduces unscheduled tool changes. Geometry that stabilises cutting and chip control The Trigon 80° form with a 0° negative rake provides a robust cutting edge that resists deformation when turning demanding alloys. The FW5 chipbreaker is designed to produce short, controllable chips even under interrupted cuts, which simplifies chip evacuation and reduces the risk of surface defects. Negative rake geometry shifts forces into a more compressive regime at the cutting edge, which is beneficial when machining tough or gummy materials where conventional positive‑rake inserts would wear prematurely. Coating and substrate benefits explained A coated carbide construction delivers the balance between wear resistance and toughness required in challenging applications. The Tiger‑tec Silver coating improves thermal resistance and reduces built‑up edge tendency, while the substrate provides the mechanical support needed for repeated engagement with hard microstructures. This means longer intervals between indexings and more consistent part quality. For users unfamiliar with coating nomenclature: the coating primarily protects the cutting edge from heat and adhesion, extending usable tool life in high‑temperature cutting zones. Practical application and selection advice This insert is supplied in the standard WNMG form factor and is best utilised in stable toolholders suited to 80° trigon inserts. The 0.8 mm corner radius contributes to a secure edge for generating good surface finishes without compromising strength. Choose this grade when facing high cutting temperatures, interrupted cuts or workpieces that tend to form long, stringy chips. For series production where repeatability and stand‑time are key, the application benefits of this insert are particularly pronounced. The Walter Tools heritage ensures compatibility with common turning systems and industrial toolholding standards. For tailored advice on selecting the right Walter Tools turning insert for specific rostfreier Stahl or superalloy applications, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the WNMG060408-FW5 WSM20S and suitable machining strategies Technical data SKU: WNMG060408-FW5-WSM20S-WALTER Designation: WNMG060408-FW5 WSM20S Manufacturer: Walter Tools Facts Plate size: 06 Thickness: 04 Corner radius: 0.8 mm Relief angle: 0° (negative) Special features Grade: WSM20S (Tiger‑tec Silver coated carbide) Chipbreaker: FW5 Shape: Trigon 80° Series: Tiger‑tec Silver Material code: S / M Execution: G Tolerance class: M FAQ Is this insert suitable for rostfreier Stahl (stainless steel)? Yes. The WNMG060408‑FW5 WSM20S is optimised for rostfreier Stahl and provides secure chip formation and edge stability when machining these alloys. How does the FW5 chipbreaker affect chip control? The FW5 chipbreaker on this insert produces short, controllable chips, improving evacuation and reducing the likelihood of surface damage during turning operations. What does the 0° negative rake mean for cutting forces? A 0° negative rake increases compressive loading at the edge; this improves edge strength and resistance to chipping when machining tough materials with the WNMG060408‑FW5 WSM20S. Can this insert be used for titanium and other superalloys? Yes. The WSM20S grade is suitable for heat‑resistant superalloys and titanium‑group materials, offering enhanced thermal resistance and stable cutting behaviour. Which toolholders are recommended for the Trigon 80° form? Standard toolholders compatible with 80° trigon inserts are appropriate; ensure a rigid set‑up to capitalise on the insert’s edge stability and to maintain consistent surface quality. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is original and new from the manufacturer.
WNMG060408-MK5 WKK10S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the MK5 chipbreaker for dependable edge performance and consistent chip control in cast iron turning; the robust Trigon 80° geometry and 0.8 mm corner radius support stable cuts and predictable tool life. Order directly via Metav Werkzeuge or consult our team for application-specific advice. WNMG060408-MK5 WKK10S indexable turning insert — Trigon 80°, for cast iron, Walter Tools The WNMG060408-MK5 WKK10S is a trigon indexable insert engineered for productive turning of cast iron components, combining a coated carbide grade with an MK5 chipbreaker for controlled, repeatable machining. Tiger·tec Silver coating for extended life Optimised for cast iron machining Trigon 80° geometry for high edge stability Reliable chip control that reduces downtime The combination of the MK5 chipbreaker and the WKK10S grade, built on Tiger·tec Silver technology, delivers consistently broken chips when machining cast iron. The cutting geometry was engineered to address the short, brittle chips typical of grey and nodular cast irons; as a result, chip evacuation is improved and tool-related interruptions are reduced. The insert’s coated carbide composition increases abrasion resistance, which translates into longer edge life under the intermittent, abrasive conditions common in cast-iron turning. Stable cutting edge for demanding operations With a Trigon 80° shape and a 0.8 mm corner radius, the insert offers a robust edge that resists chipping during heavy cuts or interrupted cuts. The negative 0° relief provides a strong cutting face and supports higher radial forces, making the insert suitable for applications requiring durability rather than aggressive shearing. Tolerance class M ensures repeatable seating in standard WNMG toolholders, which supports process consistency and simplifies tool management in production settings. Efficiency gains through material and coating synergy The Tiger·tec Silver coating, combined with the WKK10S substrate, focuses on reducing abrasive wear from cast-iron alloys. This pairing results in predictable tool wear behaviour and permits longer tool-change intervals in many applications. For workshops aiming to improve productivity and reduce per-part tooling costs, the improved wear resistance enables higher uptime and steadier component quality without complex coolant strategies. Practical integration into turning processes The insert conforms to the WNMG form factor and a compact 06 size with plate thickness 04, enabling straightforward replacement in compatible toolholders. Its MK5 chipbreaker is optimised for chip control on cast iron (ISO group K), so tool-path programmes and feed rates that worked with other WNMG inserts can often be retained with minimal adjustment. If uncertainty remains about compatibility with a specific holder or machining scenario, technical consultation is available to assist with cutting data and clamping recommendations. Contact Metav Werkzeuge today for tailored advice on Walter Tools WNMG060408-MK5 WKK10S, including recommended cutting data and availability: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: WNMG060408-MK5-WKK10S-WALTER Product type: Indexable turning insert ISO designation: WNMG060408-MK5 WKK10S Manufacturer: Walter Tools Facts Corner radius: 0.8 mm Relief angle: 0° (negative) Insert size: 06 Insert thickness: 04 Tolerance class: M Insert shape: Trigon 80° Special features Series: Tiger·tec Silver Grade: WKK10S (coated carbide) Chipbreaker: MK5 Application: Cast iron (ISO group K) Designed for abrasive wear resistance and controlled chip breaking FAQ What materials is this insert designed for? The WNMG060408-MK5 WKK10S is designed primarily for machining cast iron (ISO group K), with the grade and chipbreaker tuned for the abrasive and brittle chips typical of these materials. How does the Tiger·tec Silver coating improve performance? The Tiger·tec Silver coating on the WKK10S grade increases abrasion resistance and stabilises wear rates, which helps extend cutting edge life and maintain consistent surface finish during cast-iron turning. What benefits does the Trigon 80° shape provide? The Trigon 80° geometry offers a strong cutting edge and improved stability under higher radial loads, reducing the risk of chipping in interrupted cuts and supporting robust turning operations. Is the MK5 chipbreaker suitable for finishing passes? The MK5 chipbreaker is optimised for chip control in cast-iron machining; depending on feed and depth of cut, it can be used for both medium and certain finishing passes where controlled chips and surface quality are required. Manufacturer/Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com Protected trademarks and trade names are the property of their respective owners and are used here for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is original, brand-new merchandise from Walter Tools.
WNMG060408-MK5 WKK20S WKK20S Wendeplatten - Walter Tools
Benefit from the combination of the Tiger‑tec Silver coating and the WKK20S grade tuned for abrasive cast‑iron machining, together with the Trigon 80° geometry and MK5 chipbreaker for stable chip control; order the insert directly via Metav Werkzeuge or consult our specialists for application advice. WNMG060408-MK5 WKK20S Trigon 80° turning insert for cast iron — Walter Tools The WNMG060408-MK5 WKK20S is a Trigon 80° indexable insert optimised for cast‑iron turning, featuring the Tiger‑tec Silver coated WKK20S grade and an MK5 chipbreaker for reliable chip formation. Tiger‑tec Silver coated cutting grade WKK20S optimised for cast iron machining Trigon 80° insert geometry 0.8 mm corner radius, 0° negative rake Consistent cutting performance for abrasive cast iron The Tiger‑tec Silver technology and the WKK20S grade deliver wear resistance and consistent edge behaviour when machining cast iron. The insert’s coated carbide substrate reduces abrasive wear and extends tool life under interrupted or highly abrasive cutting conditions. By adapting the cutting grade specifically to the short, brittle chips typical of cast materials, the plate promotes stable chip formation, which translates into fewer tool changes and a more predictable production rhythm. This results in measurable improvements in productivity and lower unit machining costs. Geometry and chip control that improve process reliability The Trigon 80° shape combined with the MK5 chipbreaker and a 0.8 mm corner radius provides secure cutting entry and effective chip segmentation. The 0° negative rake creates a robust cutting edge that resists impact and maintains dimensional consistency, especially on heavy‑duty turning operations. In practical terms, this geometry reduces vibration and helps maintain surface finish, so the insert supports repeatable results on batch production runs while simplifying tool selection and clamping strategies. Practical advantages in workshop operation Designed as a workhorse for cast‑iron applications, the insert enables shorter setup times and fewer interventions thanks to its predictable wear behaviour and reliable edge security. The coated carbide construction is explained simply: a hard substrate with a specialised multi‑layer coating that reduces friction and thermal degradation. The outcome is improved tool life and more stable cycle times. For engineers and production planners, this equates to higher throughput and enhanced process control without complex parameter tuning. Contact Metav Werkzeuge for tailored machining recommendations, delivery options and technical clarification on the WNMG060408-MK5 WKK20S turning insert by Walter Tools Technical data SKU: WNMG060408-MK5-WKK20S-WALTER Designation: WNMG060408-MK5 WKK20S Product type: Turning insert (indexable) Facts Insert size: 06 Thickness: 04 Corner radius: 0.8 mm Relief angle: 0° (negative) Tolerance class: M Special features Coating/series: Tiger‑tec Silver Grade: WKK20S Chipbreaker: MK5 Geometry: Trigon 80° Applicable material group: Cast iron (K) Base material: Coated carbide FAQ What material is the insert intended for? The WNMG060408-MK5 WKK20S turning insert is specified for cast iron machining; the WKK20S grade and Tiger‑tec Silver coating are tuned to manage abrasive wear and short, breaking chips. How does the MK5 chipbreaker affect machining? The MK5 chipbreaker on the Walter Tools insert segments and evacuates chips effectively, improving surface quality and helping to avoid built‑up edge during cast‑iron turning. Is the Trigon 80° geometry suitable for heavy cutting? Yes. The Trigon 80° form with 0° negative rake gives a robust cutting edge that withstands heavy and interrupted cuts while maintaining dimensional stability. Can this insert be used for other materials besides cast iron? The WKK20S grade is optimised for cast iron (material group K); suitability for other materials is limited and should be validated for each application. What does the Tiger‑tec Silver series offer in practice? Tiger‑tec Silver provides a multi‑layer coating system that reduces friction and improves wear resistance, leading to longer tool life and more consistent machining performance with the Walter Tools turning insert. Manufacturer: Walter Tools; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are used solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered article is original factory‑new goods of the manufacturer.
WNMG060408-MM5 WMP20G WMP20G Wendeplatten - Walter Tools
Take advantage of the Tiger‑tec Gold grade and the robust Trigon 80° geometry to ensure stable chip control and extended tool life when machining stainless steels; order genuine Walter Tools inserts via Metav Werkzeuge or consult our experts for application advice. WNMG060408-MM5 WMP20G Trigon 80° turning insert – Tiger‑tec Gold · Walter Tools WNMG060408-MM5 WMP20G is a Trigon 80° turning insert engineered for reliable machining of stainless steels under medium to robust conditions, offering stable cutting edges and consistent chip control. Tiger‑tec Gold coating for wear resistance Optimised for stainless steels (ISO group M) Trigon 80° geometry for versatile turning 0.8 mm corner radius for edge stability Maximise productivity on stainless steels with consistent cutting performance The combination of the WMP20G grade within the Tiger‑tec Gold family and the MM5 chipbreaker delivers dependable cutting behaviour when working with stainless steels. The coated carbide grade is formulated to manage the toughness and heat‑generation typical of these alloys, improving chip formation and reducing edge build‑up. The insert’s Trigon form and robust cutting edge help maintain process stability, which in practice means fewer interruptions for edge changes and a more predictable cycle time in production environments. Achieve reliable surface quality and tool life through geometry and edge design The Trigon 80° geometry and a 0.8 mm corner radius provide a compromise between strength and finishing capability: the rounded corner increases resistance to chipping, while the insert form supports acceptable surface finishing on a wide range of turning tasks. The MM5 chipbreaker is designed to control chip flow in medium to heavier cuts, reducing the risk of long, stringy chips that can affect component quality or machine uptime. The negative 0° rake configuration gives a stable cutting edge for interrupted cuts and tougher workpieces, supporting consistent results across repeat batches. Integrate easily into existing tooling and benefit from proven brand performance Designed for standard WNMG toolholder systems, the insert is straightforward to inventory and deploy across production lines. The grade’s balance of wear resistance and edge stability makes it suitable for shops seeking a practical, high‑process‑security solution rather than a specialised niche grade. Walter Tools’ engineering focus on process reliability means the insert supports predictable tool life and repeatable part quality, translating to lower overall machining costs through fewer tool interventions and steadier throughput. Contact Metav Werkzeuge to discuss order options and application tuning for Walter Tools Tiger‑tec Gold inserts; our technical team is available at info@metav-werkzeuge.com or +49 2822 7131930 to advise on cutting data and availability Technical Data SKU: WNMG060408-MM5-WMP20G-WALTER Product type: Trigon turning insert Grade: WMP20G Series: Tiger‑tec Gold Facts Corner radius: 0.8 mm Free rake angle: 0° (negative) Insert size: 06 Thickness: 04 Special features Coating: Tiger‑tec Gold (coated carbide) Chipbreaker: MM5 Geometry: Trigon 80° Material application: stainless steels (ISO group M) Tolerance class: M Manufacturer: Walter Tools FAQ Which materials can this insert machine effectively? The WNMG060408-MM5 WMP20G insert is optimised for stainless steels (ISO group M) and is formulated to manage their typical toughness and heat characteristics. What benefit does the MM5 chipbreaker offer? The MM5 chipbreaker promotes secure chip control in medium to robust turning operations, improving swarf evacuation and reducing the risk of chip interference during machining. How does the Trigon 80° form influence performance? Trigon 80° geometry provides a strong cutting edge for general turning, balancing edge stability with the capability to achieve good surface quality on turned components. Is this insert compatible with standard WNMG toolholders? Yes, the insert conforms to the WNMG family dimensions and fits common toolholder systems designed for WNMG inserts, easing integration into existing tooling sets. What are the expected application conditions for the WMP20G grade? WMP20G, within the Tiger‑tec Gold series, is intended for medium to robust machining conditions on stainless steels where stable edge life and reliable chip formation are required. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (marketed as Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and forms part of the Sandvik group. Protected trademarks and product names belong to their respective owners. Original factory‑new articles are supplied by the manufacturer.
WNMG060408-MM5 WMP20S WMP20S Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Silver coating and the MM5 chipbreaker to achieve reliable chip control and extended cutting-edge life when machining rostfreier Stahl; the Trigon 80° geometry with a 0.8 mm corner radius ensures consistent surface quality and dimensional stability. Order the insert directly via Metav Werkzeuge or consult our specialists for application support. WNMG060408-MM5 WMP20S turning indexable insert — Tiger·tec Silver coating, Trigon 80° (for rostfreier Stahl) by Walter Tools WNMG060408-MM5 WMP20S is a Trigon 80° turning indexable insert designed for medium to robust machining of rostfreier Stahl, combining a specialised coated grade with a dedicated chipbreaker for improved process reliability Tiger·tec Silver coating for stable cutting WMP20S grade for rostfreier Stahl machining Trigon 80° form with 0.8 mm corner radius MM5 chipbreaker for predictable chip control Stable cutting and extended edge life for rostfreier Stahl The combination of Tiger·tec Silver coating and the WMP20S grade provides a balanced resistance to heat and wear specifically where machining rostfreier Stahl tends to generate high temperatures and built‑up edge. The coated cemented carbide substrate supports a stable cutting edge, while the coating reduces friction and enhances resistance to thermal softening. For users unfamiliar with coating technologies: the Tiger·tec Silver system applies multiple layers that protect the carbide and help maintain sharpness under elevated cutting conditions, translating into fewer insert changes and greater process uptime. Predictable chip formation and surface quality The MM5 chipbreaker is engineered to control chips reliably in medium to robust cutting scenarios, reducing the risk of long, tangled chips that can interrupt production. Combined with the Trigon 80° form and 0.8 mm corner radius, the geometry promotes a balanced contact between the tool and workpiece, improving surface finish and dimensional repeatability. In practice, this means fewer downstream operations and a more consistent part quality when turning rostfreier Stahl, even where material toughness can otherwise cause unstable cutting. Rigidity and cutting stability through geometry A 0° (negative) rake angle and the Trigon profile favour stable insertion into the cut and robust edge support, which is particularly useful when facing interrupted cuts or variable workpiece conditions. The insert’s size designation (06) and thickness (04) suit standard turning toolholders, offering mechanical stability that reduces vibration and helps maintain tolerances. For operations where fixture stiffness and tool overhang are constrained, the insert’s geometry helps preserve cutting performance and minimise the need for rework. Practical application and process integration This turning indexable insert is intended for production environments where machining rostfreier Stahl is frequent and predictable performance is essential. The WMP20S grade is optimised for the typical challenges of these materials—tendency to work harden and form adherent chips—so operators benefit from improved process security and consistent tool life. Compatibility with common clamping systems and standard toolholder interfaces allows straightforward integration into existing turning operations, reducing setup time and simplifying inventory management. For application advice or to secure the Walter Tools WNMG060408‑MM5 WMP20S insert for rostfreier Stahl machining, contact Metav Werkzeuge to discuss holder recommendations and batch availability. Technical data Article number: WNMG060408-MM5-WMP20S-WALTER Name: WNMG060408-MM5 WMP20S Manufacturer: Walter Tools Facts Form: Trigon 80° Corner radius: 0.8 mm Rake angle: 0° (negative) Size: 06 Thickness: 04 Chipbreaker: MM5 Grade: WMP20S Special features Coating: Tiger·tec Silver Suitable for: rostfreier Stahl Execution: G Series: Tiger‑tec Silver FAQ What materials is this insert intended for? The WNMG060408‑MM5 WMP20S insert is designed primarily for rostfreier Stahl, offering chip control and edge stability for medium to robust cutting conditions. What does the WMP20S grade and Tiger·tec Silver coating provide? WMP20S is a Walter Tools coated cemented carbide grade within the Tiger·tec Silver technology, providing enhanced thermal and wear resistance that supports prolonged cutting-edge life when machining rostfreier Stahl. How does the Trigon 80° form affect cutting performance? The Trigon 80° geometry gives a strong cutting edge and versatile engagement for turning, while the 0.8 mm corner radius balances strength and surface finish, improving dimensional stability in production turning. Is the insert compatible with standard toolholders? The turning indexable insert is manufactured to conventional insert dimensions (06 size, 04 thickness) and is compatible with standard clamping systems for turning operations, allowing easy integration into existing setups. The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen belongs to a global group of precision tool manufacturers and is part of the Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only. There is no affiliation between our company and the mentioned brands. The offered article is an original, factory-new product of the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
WNMG060408-MM5 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the proven combination of Tiger‑tec Silver coating and the WSM10S grade for extended tool life and consistent productivity when machining demanding materials; the trigon geometry and MM5 chipbreaker support stable chip formation and process security. For application advice or ordering, contact Metav Werkzeuge’s consultants. WNMG060408-MM5 WSM10S indexable turning insert (Trigon 80°, Tiger‑tec Silver) — Walter Tools The WNMG060408-MM5 WSM10S is an 80° trigon indexable insert designed for robust turning of rostfreier Stahl and heat‑resistant superalloys, combining a wear‑resistant coating with a geometry tuned for stable cutting. Tiger‑tec Silver coating for high wear resistance Trigon 80° geometry for robust cutting stability MM5 chipbreaker for controlled chip formation 0° negative rake with 0.8 mm corner radius Consistent performance for demanding materials The combination of the WSM10S carbide grade and the Tiger‑tec Silver coating is engineered to maintain a stable cutting edge when machining workpieces that challenge standard grades. The chemical and mechanical properties of rostfreier Stahl and superalloys tend to generate heat and cause built‑up edge; the coated grade supports secure chip flow and reduces flank wear, which in turn prolongs tool life and reduces unexpected production stops. This results in a measurable efficiency gain in batch production and greater predictability in tool change scheduling. Geometry and chip control that reduce rework The Trigon 80° form and the MM5 chipbreaker provide a balance between strength and surface finish. The insert’s 0° negative rake increases edge robustness for interrupted cuts and heavy cuts, while the 0.8 mm corner radius improves edge strength without sacrificing detail on transitional passes. Because the chipbreaker is optimised for controlled fragmentation, the machining process benefits from fewer long chips and improved surface integrity — an advantage when tight tolerances and consistent part quality are priorities. Practical application and process benefits Designed for the ISO groups S and M, this insert is suitable where heat resistance and edge stability matter most. In practice, the combination of coating, grade and geometry supports higher metal removal rates and more predictable tool life, so cycle times can be shortened without compromising finish. Process planners will appreciate the insert’s repeatability and the reduced need for frequent operator intervention. For production environments the emphasis is on process security and cost effectiveness rather than one‑off performance gains. For tailored cutting data, batch availability or material‑specific recommendations for Walter Tools WNMG060408-MM5 WSM10S inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 — consultants provide fast, application‑oriented advice and delivery options Technical data SKU: WNMG060408-MM5-WSM10S-WALTER Article: WNMG060408-MM5 WSM10S Type: Drehwendeschneidplatte / indexable turning insert Manufacturer: Walter Tools Series: Tiger‑tec Silver Facts Plate form: Trigon 80° Plate size: 06 Plate thickness: 04 Corner radius: 0.8 mm Free angle: 0° (negative) Tolerance class: M Special features Grade: WSM10S Chipbreaker: MM5 Material compatibility: S / M (superalloys, rostfreier Stahl) Execution: G Suitable for tough‑to‑cut alloys and stainless applications FAQ What materials is this insert best suited for? The WNMG060408-MM5 WSM10S insert is optimised for rostfreier Stahl and heat‑resistant superalloys (ISO groups M and S), where heat generation and edge wear are primary concerns. How does the Tiger‑tec Silver coating help in production? The Tiger‑tec Silver coating on the WSM10S grade increases wear resistance and supports consistent cutting edge behaviour, which helps extend tool life and stabilise process windows. What advantages does the Trigon 80° shape deliver? The trigon shape combines a strong cutting edge with accessibility for a range of turning operations, offering a good compromise between rigidity and finishing capability for challenging materials. Is the insert suitable for interrupted cuts? Yes; the 0° negative rake and the 0.8 mm corner radius enhance edge strength and contribute to reliable performance in interrupted machining conditions. Can this insert improve cycle times in production? When used with appropriate feeds and speeds for the workpiece, the grade and geometry of this insert help increase metal removal rates while maintaining surface quality, which supports shorter cycle times and higher throughput. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only; there is no affiliation between Metav Werkzeuge and the listed brands. The offered item is an original, factory‑new product of the manufacturer. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
WNMG060408-MM5 WSM20S WSM20S Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Silver coating, Trigon 80° geometry and a 0.8 mm corner radius for reliable machining of stainless steels and heat‑resistant superalloys; this results in stable chip formation and extended tool life. Order the insert directly via Metav Werkzeuge or ask our consultants if needed. WNMG060408-MM5 WSM20S – Indexable turning insert (Tiger‑tec Silver) for stainless steel & superalloys | Walter Tools The WNMG060408-MM5 WSM20S is an 80° Trigon indexable insert from the Tiger‑tec Silver series, designed for robust turning of stainless steels and heat‑resistant superalloys in demanding production environments. Tiger‑tec Silver coated carbide grade WSM20S Optimised for stainless steel and superalloys Trigon 80° geometry for robust cutting edges 0.8 mm corner radius with 0° negative rake Consistent edge performance in demanding materials The coated carbide grade WSM20S from the Tiger‑tec Silver family is formulated for applications where temperature and material toughness challenge the tool life. The combination of a thermally stable coating and a wear‑resistant substrate promotes stable cutting edge behaviour, which reduces the risk of built‑up edge and unplanned rework when turning stainless steels or nickel‑based alloys. This translates into predictable component quality and fewer interruptions on the shop floor, supporting steady production flow and repeatable results. Geometry that improves surface quality and chip control The Trigon 80° profile with the MM5 chipbreaker and a 0.8 mm corner radius provides a balance between edge strength and surface finish. The negative 0° rake enhances robustness under heavy engagement, while the chipbreaker is designed to split and control chips generated from tough materials. Controlled chip formation reduces workpiece marking and helps maintain consistent surface integrity; the result is better first‑pass quality and less downstream finishing. Raise productivity with fewer tool changes and higher process security A coated carbide insert like this one extends effective cutting life compared with uncoated grades, increasing uptime and lowering tool consumption per component. The stable edge and reliable wear behaviour contribute to process security and predictable tool change intervals, which in turn improve overall shop productivity. For production setups where tool availability and cycle time matter, this insert supports economical machining by reducing changeover frequency and maintaining consistent part tolerances. Practical selection and shop‑floor integration The ISO designation and indexable format make integration into existing tool holders straightforward; the insert format is compatible with common turning systems. The size and thickness data allow planners to match the insert to the holder and the intended operation type. For practical application, the WNMG060408-MM5 WSM20S performs best when cutting parameters are adapted to the material class and machine capability—Metav Werkzeuge can advise on parameter windows and holder choices for a specific turning centre or lathe. The insert suits operations from robust semi‑finishing to controlled finishing, depending on feed and speed. Contact Metav Werkzeuge for application advice on Walter Tools Tiger‑tec Silver inserts and to discuss optimal insert selection and availability Technical data SKU: WNMG060408-MM5-WSM20S-WALTER Article designation: WNMG060408-MM5 WSM20S Product type: Drehwendeschneidplatte / indexable turning insert Manufacturer: Walter Tools Facts Insert size: 06 Thickness: 04 Corner radius: 0.8 mm Free rake angle: 0° (negative) Special features Series: Tiger‑tec Silver Grade/sort: WSM20S Chipbreaker: MM5 Plate form: Trigon 80° Applicable material groups: S / M Tolerance class: M Designation without sort: WNMG060408-MM5 FAQ Which materials are recommended for this insert? The WNMG060408-MM5 WSM20S is intended for stainless steels (M) and heat‑resistant superalloys/titanium (S); the WSM20S grade and Tiger‑tec Silver technology help manage heat and support stable chip formation when machining these classes. What is the role of the MM5 chipbreaker? The MM5 chipbreaker shapes and shortens chips produced during cutting, aiding chip control and evacuation. For tough materials, this reduces the risk of long stringy chips and helps preserve surface quality. Can this insert be used for finishing stainless steel components? Yes—depending on machine rigidity and cutting parameters, the Trigon 80° geometry with a 0.8 mm corner radius can achieve good surface quality; selection of feed and speed should be matched to the material and desired finish. How does the 0° negative rake affect cutting performance? A 0° negative rake increases edge robustness and resistance to chipping under heavy engagement, making the insert suitable for demanding turning where edge strength and process security are priorities. Is Tiger‑tec Silver a coating or a substrate technology? Tiger‑tec Silver denotes a coated carbide technology combining a wear‑resistant coating with a tailored substrate; this improves thermal stability and wear resistance in high‑temperature turning operations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade marks are mentioned solely for explanatory purposes; there is no connection between our company and the mentioned brands. The offered item is an original, factory‑new product of the manufacturer Walter Tools.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com