CNMG120416-RM5 WMP20G RM5 Wendeplatten - Walter Tools
Reliable machining of stainless steels is achieved through the combination of the Tiger·tec Gold coating and the RM5 chipbreaker, delivering stable chip formation and long tool life. Benefit from predictable surface finishes and process stability; order the CNMG120416-RM5 WMP20G insert via Metav Werkzeuge or consult the specialists for application advice. CNMG120416-RM5 WMP20G – indexable turning insert for stainless steel, Tiger·tec Gold (Walter Tools) The CNMG120416-RM5 WMP20G indexable turning insert is designed for productive turning of stainless steels under moderate to robust conditions, offering a balance of wear resistance and edge security. CNMG120416-RM5 WMP20G by Walter Tools Tiger·tec Gold coating for improved wear resistance RM5 chipbreaker for secure chip formation 0° negative rake for heavy-duty turning High-performance wear resistance for stainless steels The Tiger·tec Gold technology provides a coated carbide surface that supports steady cutting under the high temperatures and adhesive tendencies of stainless steel. This results in consistent edge life and reduced flank wear, so machining cycles can be planned with greater confidence. The coated surface also helps to limit built-up edge and maintain dimensional stability over longer runs, translating into higher overall productivity and fewer unexpected tool changes. Stable chip control and robust cutting geometry The integrated RM5 chipbreaker promotes regular chip formation and evacuation, which is essential when machining materials prone to stringing or smearing. Coupled with the 0° negative rake, the geometry favours a stronger cutting edge and improved resistance to mechanical shock; this makes the insert particularly suited to interrupted cuts and tougher turning tasks. In practice, these features reduce the risk of premature edge failure and support predictable cycle times on shop-floor lathes. Practical value at the machine: predictable results and easier process planning Designed for the ISO M material group, this insert suits machining of stainless steel where control of heat and adhesion is critical. The Rhombus 80° shape and corner radius 1.6 mm deliver a compromise between form accuracy and edge strength, enabling stable finishes without sacrificing robustness. As a coated carbide solution in the Tiger·tec Gold series, the grade WMP20G is targeted at mid to heavy-duty applications where reproducible surface quality and tool longevity matter most. For reliable stainless-steel turning with Tiger·tec Gold performance, contact Metav Werkzeuge for availability and tailored application advice; eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: CNMG120416-RM5-WMP20G-WALTER Item: Drehwendeschneidplatte CNMG120416-RM5 WMP20G Walter Tools Manufacturer: Walter Tools Core specifications ISO designation: CNMG120416-RM5 WMP20G Application group: M (stainless steel) Insert size: 12 Corner radius: 1.6 mm Rake angle: 0° negative Thickness: 04 Design & special features Series: Tiger·tec Gold Grade: WMP20G Chipbreaker: RM5 Coating: coated carbide Shape: Rhombus 80° Execution: G FAQ Is this insert suitable for machining stainless steel? Yes. The CNMG120416-RM5 WMP20G grade is formulated for ISO M applications and is optimised for stainless-steel machining. What benefits does Tiger·tec Gold provide? Tiger·tec Gold coating increases wear resistance and supports stable cutting temperatures, improving coated carbide performance and tool life during stainless-steel turning. How does the RM5 chipbreaker affect production? The RM5 chipbreaker promotes controlled chip formation and evacuation, reducing the likelihood of chip-related interruptions and improving process reliability. Why choose a 0° negative rake for this insert? A 0° negative rake enhances edge strength and mechanical robustness, making the insert more resilient to impacts and suitable for heavier or interrupted cuts. What geometry details are important for part quality? The Rhombus 80° shape with a corner radius 1.6 mm balances finish quality and edge durability, aiding consistent dimensional results. Manufacturer: Walter Tools. Protected trademarks and trade names are the property of their respective owners. Brand names are used for explanatory purposes only; there is no affiliation between Metav Werkzeuge and the mentioned manufacturers. The offered item is an original, factory-new product of the manufacturer.
CNMG120416-RM5 WMP30G WMP30G Wendeplatten - Walter Tools
Take advantage of the combination of durable Tiger‑tec Gold coating, RM5 chip control and robust edge geometry for reliable stainless‑steel turning; order the insert directly via Metav Werkzeuge or consult the technical team for application matching. CNMG120416-RM5 WMP30G indexable turning insert — Walter Tools, optimised for stainless steel machining CNMG120416-RM5 WMP30G is an indexable turning insert designed for secure cutting and stable chip formation in stainless‑steel applications, suited to medium to heavy conditions Tiger‑tec Gold coating for improved tool life Optimised RM5 chipbreaker for stainless steel Rhombic 80° geometry for versatile turning 1.6 mm corner radius for robust edge strength Consistent performance in stainless‑steel turning The insert grade WMP30G, used in the Tiger‑tec Gold series, is engineered for rostfreier Stahl where material toughness and heat generation demand stable cutting behaviour. The combination of a tailored coating and substrate supports controlled friction and reduced built‑up edge, which in practice leads to longer uninterrupted cutting intervals. The integrated RM5 chipbreaker promotes reliable chip segmentation under varying feeds, improving process stability and reducing tool‑related interruptions in productive setups. Reliable edge stability and repeatable results The rhombic 80° geometry and a 1.6 mm corner radius provide a balance between edge strength and form versatility, making the insert suitable for both finishing and semi‑roughing passes where repeatability matters. The 0° (negative) rake characteristic increases edge robustness, helping maintain an even cutting edge under higher mechanical loads. This geometry supports consistent dimensional results and a predictable tool life profile, which is particularly valuable in series production and contract machining. Practical benefits for production efficiency Using an indexable format reduces tool change time and simplifies inventory management compared with brazed tools. The CNMG outline offers access to common toolholder families, while the plate thickness code and form support adequate rigidity for heavier cuts. Improved chip control from the RM5 design lowers the need for manual chip clearing and minimises risk to finished surfaces, contributing to smoother workflow and reduced secondary operations in the machining cell. Guidance on selection and technical explanation The designation indicates the insert form and intended function: a rhombic insert with a medium to robust corner radius and dedicated chipbreaker for stainless‑steel machining. The Tiger‑tec Gold coating is a multilayer PVD/CVD technology tailored to reduce adhesion and extend wear resistance on tough alloys. For users assessing tooling options, the CNMG120416‑RM5 WMP30G insert from Walter Tools is a practical choice where stable chip formation and extended edge life are priorities; Metav Werkzeuge can advise on matching holders and cutting parameters. Contact Metav Werkzeuge for tailored cutting data and application advice on the CNMG120416‑RM5 WMP30G insert at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: CNMG120416-RM5-WMP30G-WALTER ISO designation: CNMG120416-RM5 WMP30G Manufacturer: Walter Tools Series: Tiger‑tec Gold Facts Insert size: 12 Corner radius: 1.6 mm Free angle: 0° (negative) Plate form: Rhombus 80° Thickness code: 04 Special features Chipbreaker: RM5 Grade: WMP30G (coated carbide) Execution: G Suitable for: rostfreier Stahl FAQ What materials is this insert suitable for? The CNMG120416‑RM5 WMP30G insert is specified for rostfreier Stahl (stainless steel) and is optimised for the typical cutting behaviour of that group. What advantage does the Tiger‑tec Gold coating provide? Tiger‑tec Gold on the WMP30G grade enhances wear resistance and reduces adhesion, supporting longer cutting intervals and more consistent tool life when machining stainless steels. How does the RM5 chipbreaker affect machining? The RM5 chipbreaker promotes controlled chip segmentation for improved evacuation and surface integrity; the design helps maintain stable cutting even under varying feeds. Is the rhombic 80° geometry versatile for different turning tasks? Yes, the rhombic 80° form offers access to various turning operations and toolholder types while balancing approach angle and strength for both finishing and semi‑roughing. How is the corner radius relevant for application? A 1.6 mm corner radius provides increased edge strength, reducing the likelihood of chipping under heavier cuts and contributing to repeatable dimensional results. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation. There is no affiliation between our company and the named brands. The offered item is original, factory‑new goods of the manufacturer Walter Tools.
CNMG120416-RM5 WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating, RM5 chip control and a robust rhombic 80° geometry for reliable turning of stainless steel and heat‑resistant superalloys; order directly via Metav Werkzeuge or contact our technical consultants for machining recommendations CNMG120416-RM5 WSM20S indexable turning insert (Tiger‑tec Silver) for stainless steel & superalloys — Walter Tools CNMG120416-RM5 WSM20S is an indexable turning insert optimised for heavy and challenging turning tasks on stainless steel and heat‑resistant superalloys, providing stable cutting edges and secure chip control Tiger‑tec Silver coated carbide grade WSM20S RM5 chipbreaker for secure chip control Rhombic 80° form with 1.6 mm corner radius Negative 0° rake for stable cutting Consistent performance on stainless steel and superalloys The combination of the WSM20S coated carbide grade and the Tiger‑tec Silver series delivers an engineered balance between wear resistance and edge stability that is essential when machining stainless steel or heat‑resistant superalloys. The insert’s composition supports controlled wear and avoids premature flank damage, which improves process reliability and reduces unplanned tool changes. The integrated RM5 chipbreaker contributes to predictable chip formation, lowering the risk of built‑up edge formation and improving surface integrity in each pass. Geometry engineered for secure cutting and long tool life A rhombic 80° insert form with a 1.6 mm corner radius and 0° (negative) rake offers a stable cutting geometry that tolerates interrupted cuts and heavy engagement. The modest corner radius increases edge strength for roughing while preserving acceptable surface finish during finishing passes. The negative rake angle stabilises the cutting action under high radial loads, which makes this grade suitable for operations demanding robust edge retention. Coated cemented carbide construction ensures thermal resistance and adhesion of the coating under elevated cutting temperatures. Productivity benefits and process security in production Using a dedicated grade from the Tiger‑tec Silver family yields measurable production advantages: improved tool life and more consistent cutting forces lower cycle time variability and decrease rework rates. The WSM20S grade is designed for the ISO groups S and M, meaning it is appropriate for both superalloys and stainless steel — materials known for poor heat conduction and a tendency to work‑harden. With better chip control and edge stability, the insert supports steady production runs and predictable maintenance intervals, contributing to overall process efficiency. Application guidance and machining behaviour This insert is suitable for a range of turning tasks where robustness is required: heavy roughing of bars and shafts, semi‑finishing passes where interrupted cuts occur, and applications involving materials that demand high thermal and mechanical stability. The RM5 chipbreaker is tuned for secure chip flow on sticky, work‑hardening materials; the rhombic 80° shape offers versatility across insert seatings and holders. For fine finishing on stainless steel, consider machining parameters that reduce built‑up edge risk and favour stable coolant and feed settings to exploit the insert’s coated carbide advantages. Contact Metav Werkzeuge for tailored grade selection and application advice on Walter Tools inserts — info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: CNMG120416-RM5-WSM20S-WALTER Article designation: CNMG120416-RM5 WSM20S Product type: indexable turning insert Facts Grade/series: WSM20S / Tiger‑tec Silver Shape: rhombic 80° Corner radius: 1.6 mm Rake: 0° (negative) Thickness: 04 Size: 12 Special features Chipbreaker: RM5 Material compatibility: S / M Application: heavy machining, interrupted cut capability Coated cemented carbide for thermal stability Tolerance class: M Execution: G FAQ What materials is this insert designed for? The CNMG120416‑RM5 WSM20S insert (Walter Tools, Tiger‑tec Silver) is designed primarily for stainless steel and heat‑resistant superalloys (ISO groups M and S). How does the RM5 chipbreaker influence machining? The RM5 chipbreaker on the CNMG120416‑RM5 promotes secure chip control and predictable chip shapes, which helps to reduce built‑up edge and improve surface quality when machining sticky or work‑hardening materials. Which operations suit the rhombic 80° form best? Rhombic 80° inserts are versatile for facing and turning operations; the CNMG120416‑RM5 excels in roughing and semi‑finishing where strong edge support and resistance to interruption are required. Is the WSM20S grade suitable for high temperatures? Yes, the WSM20S grade within the Tiger‑tec Silver family is formulated for enhanced thermal resistance and edge stability under the elevated temperatures typical when machining stainless steel and superalloys. Can this insert be used for finishing passes? While primarily offering robustness for heavier cuts, the insert can be used for semi‑finishing and certain finishing passes depending on the chosen corner radius and cutting parameters. Walter Tools / Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trade names are mentioned solely for explanation. There is no connection between our company and the named brands. The offered item is original, factory‑new goods of the manufacturer.
CNMG120416-RM5 WSM30S RM5 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, a robust RM5 chipbreaker and the 1.6 mm corner radius for reliable machining of tough materials; order the insert directly via Metav Werkzeuge or consult our specialists for matching grade selection. CNMG120416-RM5 WSM30S indexable turning insert — Walter Tools, Tiger·tec Silver coated for stainless steels and superalloys The CNMG120416-RM5 WSM30S is an indexable turning insert engineered for stable performance in rostfreier Stahl and heat-resistant alloys, featuring a rhombic 80° geometry for versatile turning tasks. Tiger·tec Silver coated carbide grade WSM30S Designed for rostfreier Stahl and superalloys Rhombic 80° insert with 1.6 mm corner radius Negative 0° rake; RM5 chipbreaker for tight control Consistent cutting performance for demanding alloys The coated carbide WSM30S grade, using Tiger·tec Silver technology, is formulated to maintain a stable cutting edge under thermal and mechanical stress. This results in predictable tool life and fewer unscheduled tool changes when machining stainless steels and nickel-based superalloys. The insert’s composition promotes controlled chip formation and reduces edge build-up, which directly supports higher process reliability and improved component quality in serial production. Geometry that combines strength with precision The rhombic 80° shape and a 1.6 mm corner radius provide a compromise between edge strength and surface finish. The negative 0° clearance offers extra support to the cutting edge for interrupted cuts and hard-facing conditions, while the RM5 chipbreaker is optimised for tight chip control in demanding materials. Together, these features enable robust turning with reduced vibration and consistent dimensional results, particularly in roughing-to-finishing transitions. Practical advantages for workshop productivity As an indexable turning insert, the item reduces setup time and minimises tooling inventory by allowing multiple indexings per insert. The combination of a proven coating system and a stable chipformer lowers machining costs through extended life and fewer regrinds. For shop floors working with mixed batches of stainless steels and heat-resistant alloys, this grade offers versatility and dependable performance that supports continuous production flow. Application guidance and machining notes The insert is particularly suited to turning operations on materials classified under ISO groups M and S, meaning rostfreier Stahl and heat-resistant superalloys including titanium grades. For best results, select cutting parameters that balance moderate cutting speed with stable feed to ensure the WSM30S coating supports steady thermal conditions; the RM5 chipbreaker helps maintain short, manageable chips under these regimes. For specialised applications or uncertain process windows, technical consultation is recommended to confirm optimal parameters. Discuss specific machining requirements or request procurement of the CNMG120416-RM5 WSM30S with Metav Werkzeuge’s specialists to ensure the correct grade and geometry for the application Technical Data SKU: CNMG120416-RM5-WSM30S-WALTER Designation: CNMG120416-RM5 WSM30S Product type: Indexable turning insert Brand: Walter Tools Numbers / Core Technical Data Insert size: 12 Corner radius: 1.6 mm Thickness: 04 Clearance angle: 0° (negative) Tolerance class: M Special features Coating: Tiger·tec Silver Grade: WSM30S (coated carbide) Chipbreaker: RM5 Plate form: Rhombic 80° Material suitability: S / M; rostfreier Stahl indicated FAQ Is this insert suitable for stainless steels? Yes. The CNMG120416-RM5 WSM30S from Walter Tools is specifically designed for rostfreier Stahl (ISO group M) and provides stable chip formation and edge life in these materials. Can the insert be used on nickel-based superalloys or titanium? The WSM30S grade is intended for hard-to-machine materials, including heat-resistant superalloys (ISO group S); consult machining data for parameter adjustment when working with titanium alloys. What does the RM5 chipbreaker deliver in practice? The RM5 chipbreaker on the CNMG120416-RM5 promotes short, controlled chips and reduces the risk of chip entanglement, improving surface quality and process security in turning operations. How does the negative 0° clearance affect machining? A negative 0° clearance increases edge support and robustness, making the insert more resistant to cutting edge chipping during interrupted cuts and heavy radial engagement. What advantages does the Tiger·tec Silver coating provide? Tiger·tec Silver enhances wear resistance and thermal stability of the coated carbide, contributing to longer tool life and consistent performance across serial production. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names remain the property of their respective owners. Brand names are mentioned for explanatory purposes only and do not imply any affiliation between our company and the mentioned manufacturers. The offered article is original, brand-new goods from the manufacturer.
CNMG120416-RP5 WPP05G WPP05G Wendeplatten - Walter Tools
Take advantage of the proven combination of Tiger‑tec Gold coating and the RP5 chipbreaker to secure consistent metal removal in steel turning. Benefit from a robust 1.6 mm corner radius and 0° negative rake for reliable performance and reduced tool changes. Order directly via Metav Werkzeuge or request tailored advice from our consultants. CNMG120416-RP5 WPP05G turning insert for steel — Tiger‑tec Gold, RP5 — Walter Tools CNMG120416-RP5 WPP05G is a rhombic 80° turning insert designed for productive steel machining in industrial turning applications CNMG 120416 geometry, Rhombus 80° insert Tiger‑tec Gold coated carbide grade WPP05G RP5 chipbreaker for reliable chip control 1.6 mm corner radius and 0° negative rake Higher metal removal with robust edge security The combination of the Tiger‑tec Gold coating and the WPP05G carbide grade offers a wear-resistant, coated cutting substrate that is optimised for the thermal and mechanical demands of steel machining. The 1.6 mm corner radius increases edge strength, delaying flank wear and allowing more aggressive feeds without compromising repeatability. For production environments, this means fewer tool changes and improved process stability, translating into measurable cycle-time savings and predictable tool life. Consistent chip control for smoother cycles Equipped with the RP5 chipbreaker, the insert produces controllable chip form during a wide range of cutting parameters in the steel group. The dedicated chip geometry reduces the risk of long, tangled chips and supports uninterrupted operation in automated or semi-automated lathes. Clear chip evacuation contributes directly to surface quality and lowers the likelihood of secondary operations, supporting a smoother manufacturing workflow and higher first-pass yield. Machining security through geometry and rake design The Rhombus 80° shape and 0° negative rake provide a sturdy cutting edge suited to general turning tasks, including medium to heavy cuts where edge resilience is essential. The insert’s tolerance class M denotes consistent dimensional conformity for indexed replacements and fixture repeatability. Together, these design choices foster reliable performance across batch production and job-shop settings, particularly when working with unalloyed and alloyed steel according to ISO P group specifications. Practical selection and application guidance This indexable insert is supplied in the CNMG format with the RP5 chipbreaker and belongs to the Tiger‑tec Gold series. It is intended primarily for turning operations in the steel material group and is compatible with common CNMG toolholders. When replacing inserts, match the insert geometry and clamping system and consider ramping down feed for high alloy steels until optimum parameters are verified. The coated carbide construction balances toughness and wear resistance for a broad range of steel machining tasks. Contact Metav Werkzeuge for bespoke tooling recommendations and reference CNMG120416-RP5 WPP05G from Walter Tools to receive detailed application support and availability information. Technical data Article number: CNMG120416-RP5-WPP05G-WALTER SKU: CNMG120416-RP5-WPP05G-WALTER Designation: CNMG120416-RP5 WPP05G Manufacturer: Walter Tools Series: Tiger‑tec Gold Core data Insert form: Rhombus 80° Corner radius: 1.6 mm Insert size: 12 (CNMG 120416 format) Thickness: 04 Rake angle: 0° (negative) Chipbreaker: RP5 Tolerance class: M Special features Coating: Tiger‑tec Gold (coated carbide) Grade: WPP05G Application group: Steel (ISO P) Execution: G FAQ What steels is this insert suitable for? The CNMG120416-RP5 WPP05G from Walter Tools is formulated for the ISO P steel group, covering unalloyed and alloyed steels with an emphasis on typical steel heat and chip formation behaviour. Which chipbreaker should be selected for reliable chip control? The RP5 chipbreaker fitted to this CNMG insert provides controlled chip formation for a wide parameter window when machining steel with Tiger‑tec Gold coated carbide. How does the 0° negative rake affect cutting? A 0° negative rake increases cutting-edge robustness and is advantageous in interrupted cuts or heavier depths of cut; the insert CNMG120416-RP5 WPP05G leverages this for enhanced edge security. Is this insert suitable for automated turning centres? Yes — the combination of a coated carbide grade and the RP5 chipbreaker makes this insert appropriate for automated lathes where consistent chip control and tool life are required. Walter Tools: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered article is original, factory-new goods of the manufacturer.
CNMG120416-RP5 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of a high-performance, wear-resistant grade combined with a robust geometry for consistent steel machining and predictable tool life; the Tiger·tec Gold coating and the RP5 chipbreaker ensure stable chip control and reduced rework. Order the original inserts directly via Metav Werkzeuge or consult the technical team for process optimisation. CNMG120416-RP5 WPP10G — Indexable turning insert for steel, Tiger·tec Gold, Walter Tools The CNMG120416-RP5 WPP10G is an indexable turning insert designed for productive steel machining with optimised chip control and a robust cutting edge suitable for diverse turning operations. Tiger·tec Gold coating for extended life Optimised RP5 chipbreaker for stable chips Rhombic 80° form for versatile turning 1.6 mm nose radius; 0° negative rake Increased productivity through a wear-resistant grade The combination of the Tiger·tec Gold coating and the WPP10G grade delivers a well-balanced mix of wear resistance and toughness tailored for steel applications. This coated carbide composition is engineered to handle the heat and specific chip formation encountered when machining steels, which leads to longer tool life and fewer tool changes. By reducing unplanned stops and downtime, the insert contributes directly to a more efficient production flow and predictable batch outcomes. Reliable chip control that simplifies downstream processes The RP5 chipbreaker has been developed to produce short, controllable chips in a wide range of steel turning tasks. Stable chip formation reduces the risk of entanglement, improves surface consistency and lowers the need for secondary cleaning or rework. For operations focused on cycle time and reproducible quality, the controlled chips help maintain throughput while protecting both the workpiece and the machine tool. Geometry engineered for strength and versatility The Rhombic 80° shape combined with a 0° (negative) rake angle increases edge strength for heavier cuts and interrupted operations. The 1.6 mm corner radius offers a balance between robustness and the ability to produce acceptable surface finishes on external profiles and shoulders. Where process reliability and tool security are priorities—for example, mixed batch production or roughing passages—this geometry supports stable cutting forces and consistent results. Practical handling and process guidance Designed as a standard ISO-style insert, this plate is simple to index and replace, reducing setup time and improving machine uptime. The grade’s focus on steel machining means it performs well across unalloyed and alloyed steels, giving workshop planners a dependable option for general turning tasks. For additional guidance on parameters or integration into an existing toolset, technical consultation is available; contact details are provided for further specification or process-adaptive advice. For robust steel turning with Walter Tools’ Tiger·tec Gold grade, contact Metav Werkzeuge for ordering and process recommendations Technical data Article number: CNMG120416-RP5-WPP10G-WALTER Designation: CNMG120416-RP5 WPP10G Type: Indexable turning insert Manufacturer: Walter Tools Facts Nose radius: 1.6 mm Relief angle: 0° (negative) Size designation: 12 Thickness designation: 04 Tolerance class: M Special features Coating/series: Tiger·tec Gold Grade: WPP10G Chipbreaker: RP5 Plate form: Rhombic 80° Material application: Steel (P) Execution: G FAQ What materials can be machined with this insert? This insert is specified for machining steels; the WPP10G grade and its Tiger·tec Gold coating are optimised for P-group materials according to ISO classification. What advantage does the RP5 chipbreaker provide? The RP5 chipbreaker creates short, controlled chips in steel turning, improving process safety and surface consistency while reducing chip-related interruptions. Is the geometry suitable for interrupted cuts and heavy roughing? The rhombic 80° form with a 0° (negative) rake and a 1.6 mm corner radius gives enhanced edge strength, making the insert well suited to interrupted cuts and robust roughing operations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are referenced for explanatory purposes only and do not indicate any affiliation or endorsement. The offered item is an original, factory-new product of the manufacturer Walter Tools.
CNMG120416-RP5 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating, the RP5 chipbreaker and the Rhombic 80° CNMG geometry for consistent, productive steel turning — order the insert via Metav Werkzeuge or consult our specialists for application-specific recommendations. CNMG120416-RP5 WPP20G Walter Tools – Indexable turning insert with Tiger‑tec Gold coating and RP5 chipbreaker A CNMG120416-RP5 WPP20G turning insert designed for robust steel machining, offering controlled chip formation and extended tool life for medium to universal cutting conditions Tiger‑tec Gold coating for long tool life Optimised RP5 chipbreaker for steel turning Rhombic 80° CNMG 12 mm insert geometry 0° negative rake, 1.6 mm corner radius Consistent productivity for steel turning operations The combination of the WPP20G grade and the Tiger‑tec Gold coating delivers a stable wear behaviour that reduces process variability. As a coated cemented carbide grade tuned for steel applications, the insert enables reliable material removal rates and predictable tool-life windows. This consistency supports higher machine utilisation and fewer unplanned tool changes, which directly improves throughput on serial production and jobbing environments. Coating and grade: extended lifetime with predictable wear The Tiger‑tec Gold surface treatment provides enhanced resistance to abrasive and adhesive wear while maintaining edge stability under the thermal loads typical of steel cutting. The WPP20G chemistry balances toughness and wear resistance, making the insert suitable for a broad range of cutting speeds and feeds. For shops seeking efficiency, the improved coating performance translates into longer intervals between indexings and reduced tooling costs per component. Geometry and chip control that improve surface finish The Rhombic 80° CNMG form combined with the RP5 chipbreaker offers controlled chip formation and secure edge support for medium turning tasks. The 1.6 mm corner radius and 0° negative rake create a robust cutting edge that tolerates interrupted cuts and offers better stability in roughing-in passes. As a result, workpieces benefit from more consistent surface quality and fewer rework steps, particularly when machining general steel grades. Practical advantages in the workshop and on the machine Specifically tailored to steel machining (material group P), the insert’s features simplify process planning: the RP5 chipbreaker assists swarf evacuation while the insert geometry is compatible with standard CNMG holders. Toolrooms can expect easier parameter transfer between machines and less trial-and-error when ramping up new programmes. The clear material designation and series information reduce the effort needed for tool selection and inventory management. Contact Metav Werkzeuge today to discuss Walter Tools Tiger‑tec Gold inserts and to specify the CNMG120416-RP5 WPP20G for optimised steel turning performance Technical data SKU: CNMG120416-RP5-WPP20G-WALTER Article designation: CNMG120416-RP5 WPP20G Product type: Turning insert (indexable) Series: Tiger‑tec Gold Grade: WPP20G Manufacturer: Walter Tools Facts Insert size: 12 Corner radius: 1.6 Relief angle: 0° (negativ) Insert shape: Rhombus 80° Plate thickness: 04 Tolerance class: M Special features Coating: Tiger‑tec Gold Chipbreaker: RP5 Material suitability: P (steel) Geometry: CNMG120416-RP5 Application: Turning/indexable insert FAQ What materials is this insert suited for? The CNMG120416-RP5 WPP20G is formulated for steel machining (material group P) and is optimised for the typical heat and chip characteristics encountered when turning unalloyed and alloyed steels. How does the Tiger‑tec Gold coating affect tool life? The Tiger‑tec Gold coating on the WPP20G grade improves resistance to abrasive and adhesive wear, which extends the service life of the Walter Tools insert under comparable cutting conditions. What is the advantage of the RP5 chipbreaker? The RP5 chipbreaker provides controlled chip formation and reliable swarf control during steel turning, reducing the risk of tangling and aiding safer, cleaner machining cycles. Is this insert compatible with standard CNMG toolholders? Yes, the Rhombic 80° CNMG geometry of the CNMG120416-RP5 WPP20G matches standard CNMG toolholders; holders should be checked for seat condition and clamping integrity prior to use. Which cutting strategies benefit most from this insert? The robust edge and 1.6 mm corner radius make the insert well suited to medium turning and operations with occasional interruptions; it supports stable roughing and semi-finish passes in steel production. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation only and do not imply any association with our company. The offered item is an original, factory‑new product of Walter Tools.
CNMG120416-RP5 WPP30G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating, a purpose‑built RP5 chipbreaker and a stable negative rake to boost turning productivity on steel; order directly via Metav Werkzeuge or consult our advisors for application support. CNMG120416-RP5 WPP30G turning insert — Tiger‑tec Gold coated carbide for steel, Walter Tools CNMG120416-RP5 WPP30G is a coated turning insert designed for precision steel machining with reliable chip control and extended tool life CNMG 80° rhombic insert, 1.6 mm corner radius Tiger‑tec Gold coated carbide grade WPP30G Optimised RP5 chipbreaker for steel turning Negative 0° rake for stable roughing cuts High wear resistance for industrial steel turning The Tiger‑tec Gold technology combined with the WPP30G grade provides a coated carbide surface engineered for consistent performance when machining steels. This coating reduces abrasive wear and improves thermal resistance, which leads to longer cutting edge life and fewer insert changes. For production environments where uptime matters, the result is a measurable increase in machining efficiency and reduced tooling costs per component. Geometry that delivers process security and chip control The CNMG rhombic 80° geometry with a 1.6 mm corner radius and negative 0° rake angle offers robust cutting behaviour, particularly for interrupted or heavy cuts. The RP5 chipbreaker is optimised for steady chip formation when cutting steel (ISO P), enabling predictable material evacuation and minimised risk of built‑up edge. This combination supports stable roughing and medium finishing operations with improved dimensional repeatability. Designed for versatility on a wide range of steels Classified for ISO P applications, this insert is suitable for unalloyed and alloyed steels commonly encountered in general engineering. The WPP30G sort balances wear resistance and toughness so that the insert copes with varying cutting conditions while maintaining edge integrity. In practice, this means fewer tool changes during batch runs and more consistent surface quality across workpieces. Practical identification and installation for workshop use The insert is designated CNMG120416-RP5 WPP30G, tolerance class M, and belongs to the Tiger‑tec Gold series — details that simplify inventory control and toolholder selection. The plate form (rhombus 80°) and thickness code facilitate straightforward mounting in standard turning toolholders. For tailored cutting data or to confirm compatibility with specific toolholders and turning centres, Metav Werkzeuge provides application advice and technical data sheets. For high‑productivity steel turning with Tiger‑tec Gold, contact Metav Werkzeuge for application recommendations and availability of the CNMG120416-RP5 WPP30G insert. Technical Data SKU: CNMG120416-RP5-WPP30G-WALTER Designation: CNMG120416-RP5 WPP30G Manufacturer: Walter Tools Facts Corner radius: 1.6 mm Inscribed circle / size: 12 Thickness code: 04 Rake angle: 0° (negative) Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WPP30G Chipbreaker: RP5 Suitable for: Steel (ISO P) Plate form: Rhombus 80° Coated carbide cutting material FAQ What materials is this insert best suited for? The CNMG120416-RP5 WPP30G insert is optimised for steels (ISO P); the WPP30G grade and Tiger‑tec Gold coating are designed to manage the heat and chip formation typical of steel machining. How does the RP5 chipbreaker affect machining? The RP5 chipbreaker on the CNMG120416-RP5 WPP30G promotes controlled chip formation during turning of steel, improving evacuation and reducing the chance of entanglement or built‑up edge. Can this insert be used for roughing and finishing? Yes; the combination of a 1.6 mm corner radius and negative 0° rake provides robustness for roughing while still allowing medium finishing passes when appropriate parameters are selected for the CNMG120416-RP5 WPP30G. What benefits does the Tiger‑tec Gold coating provide? Tiger‑tec Gold on the WPP30G grade enhances wear resistance and thermal stability during steel machining, resulting in longer tool life and more consistent part quality. How are the inserts identified for stock and replacement? Inserts are identified by the full designation CNMG120416-RP5 WPP30G; this simplifies ordering, inventory and matching to compatible turning toolholders. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand presentation: Walter Tools) is part of a global portfolio of precision tooling manufacturers. Protected trademarks and trade names remain the property of their respective owners. The mentioned brand names are used solely for explanatory purposes. The offered item is an original, factory‑new product of the manufacturer.
CNMG120416-RP7 WPP10G WPP10G Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Gold coating for extended tool life, the RP7 chipbreaker for consistent chip control and the robust 1.6 mm corner radius for stable cutting performance; order the CNMG120416‑RP7 WPP10G directly via Metav Werkzeuge or consult the technical team for tailored application advice. CNMG120416-RP7 WPP10G — Turning insert, Tiger‑tec Gold coated, RP7 chipbreaker (Walter Tools) The CNMG120416-RP7 WPP10G is a rhombic 80° indexable turning insert engineered for steel machining, combining a wear-resistant coating with a chipbreaker designed for reliable material evacuation in general turning operations Tiger‑tec Gold coated for long tool life RP7 chipbreaker for consistent chip control 80° rhombic shape for versatile turning Maximise cutting performance with advanced coating and chip control The Tiger‑tec Gold technology and the WPP10G grade deliver a balance between wear resistance and toughness that suits a wide variety of steels under ISO P. The RP7 chipbreaker promotes predictable chip formation, which reduces secondary operations and improves cycle-time stability. This combination supports higher process reliability and more consistent surface finishes, enabling productive machining where repeatability and cost-efficiency are priorities. The insert’s coated carbide substrate reduces flank wear and prolongs useful life under continuous production loads. Robust geometry for heavy-duty turning and reliable edge security The rhombic 80° geometry and a 1.6 mm corner radius provide enhanced mechanical strength at the cutting edge, while the 0° (negative) relief angle increases edge support during interrupted cuts or heavy stock removal. These geometric choices reduce the risk of edge chipping and maintain dimensional control in demanding turning applications. The result is a tool that stands up to tougher operations, offering fewer tool changes and steadier toolpaths, which in turn supports higher machine utilisation and lower overall tooling costs. Application versatility and integration into standard tool systems Designed for steel machining (ISO P), this insert is suitable for general turning and mixed-batch production where a combination of durability and predictable chip control matters. The CNMG designation ensures compatibility with standard CNMG toolholders, allowing straightforward integration into existing tooling setups. With its focus on process security and broad material coverage, the insert is appropriate for job shops and production environments seeking to improve throughput and surface quality with a single, dependable grade from Walter Tools. Contact Metav Werkzeuge for personalised cutting data, availability and grade recommendations based on specific steel grades and machining strategies: info@metav-werkzeuge.com, +49 2822 7131930 Technical data SKU: CNMG120416-RP7-WPP10G-WALTER Article designation: CNMG120416-RP7 WPP10G Brand: Walter Tools Series: Tiger‑tec Gold Grade: WPP10G Numbers / Core technical data Corner radius: 1.6 mm Relief angle: 0° (negative) Shape: Rhombus 80° Inscribed circle / size: 12 Thickness code: 04 Tolerance class: M Special features / Design and application Chipbreaker type: RP7 Coating / substrate: Tiger‑tec Gold coated carbide Material application: Steel (ISO P) Robust edge geometry for interrupted cuts and heavy stock removal Indexable insert, CNMG form for standard holders FAQ What materials are suitable for this insert? The CNMG120416‑RP7 WPP10G is specified for steel machining (ISO P) and is designed to cope with the typical heat and chip characteristics encountered when turning unalloyed and alloyed steels. How does the RP7 chipbreaker improve machining? The RP7 chipbreaker on this insert promotes controlled chip formation and evacuation, which supports consistent surface quality and reduces the likelihood of chip-related interruptions in continuous production. Is the insert compatible with standard CNMG toolholders? Yes, the CNMG geometry denotes compatibility with standard CNMG toolholders, allowing the CNMG120416‑RP7 WPP10G to be fitted into established tool setups without special adaptations. What advantage does the Tiger‑tec Gold coating provide? Tiger‑tec Gold offers enhanced wear resistance while maintaining toughness, improving tool life and process reliability across a broad range of steel turning applications. When is a negative relief angle beneficial? A 0° (negative) relief angle increases edge support and is particularly beneficial for interrupted cuts or when higher edge strength is required, helping to prevent chipping and extend usable life. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany; Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanation only. There is no affiliation between our company and the mentioned brands. The offered article is original, factory-new goods from the manufacturer.
CNMG120416-RP7 WPP20G G Wendeplatten - Walter Tools
Combining the Tiger·tec Gold coating of the WPP20G grade with the robust CNMG geometry and a 1.6 mm corner radius delivers high productivity and consistent edge life for steel turning; order the CNMG120416-RP7 WPP20G directly via Metav Werkzeuge or contact the consultants for technical guidance. CNMG120416-RP7 WPP20G – Turning insert with Tiger·tec Gold coating for steel (Walter Tools) The CNMG120416-RP7 WPP20G is an indexable turning insert engineered for productive, reliable machining of steel components, offering a rhombic 80° geometry and a coated-carbide grade optimised for chip control and wear resistance. Tiger·tec Gold coated carbide grade WPP20G Rhombic 80° geometry for stable cutting 1.6 mm corner radius for robust edge life 0° negative rake for heavy cutting Higher throughput when machining steel with coated Tiger·tec Gold The combination of the Tiger·tec Gold coating and the WPP20G grade provides elevated thermal and abrasive resistance, designed specifically for the ISO P material group. This configuration improves chip formation and reduces flank wear under typical steel cutting temperatures, enabling longer tool life and reduced tooling costs per component. The coated-carbide substrate maintains dimensional stability across varied cutting regimes, supporting consistent cycle times and fewer insert changes on production lines. Stable cutting performance from geometry and edge design The rhombic 80° geometry with a 1.6 mm corner radius and 0° negative rake yields a balanced mix of strength and accessibility to the cut. The geometry resists chipping during interrupted cuts and heavy engagement, while the corner radius offers a compromise between durability and surface finish. The integrated RP7 chipbreaker promotes predictable chip flow in longitudinal turning, helping to maintain process stability and reliable surface quality with fewer manual interventions. Versatility, handling and process support for workshop use Tolerance class M and the proven Tiger·tec Gold series make this insert suitable for a broad range of steel applications, from unalloyed to alloyed steels as classified under ISO P. The insert’s specification supports both high-feed roughing and controlled finishing operations when paired with appropriate cutting parameters. For supplementary application data, cutting recommendations or compatibility checks, technical enquiries can be directed to Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by telephone at +49 2822 7131930; consultants provide targeted advice to match the insert to machine and process requirements. For reliable, high-productivity steel turning with Walter Tools’ Tiger·tec Gold, contact Metav Werkzeuge for expert supply and application advice Technical data SKU: CNMG120416-RP7-WPP20G-WALTER Designation: CNMG120416-RP7 WPP20G Product type: Turning insert Data Plate size: 12 Plate thickness: 04 Corner radius: 1.6 Rake angle: 0° (negative) Plate form: Rhombus 80° Tolerance class: M Special features Series: Tiger·tec Gold Grade: WPP20G (coated carbide) Chipbreaker: RP7 Execution: G Material group: P (steel) Suitable for machining steel according to ISO P FAQ Is this insert suitable for machining steel? The CNMG120416-RP7 WPP20G insert from Walter Tools is specified for the ISO P material group and is optimised for machining unalloyed and alloyed steels. What chipbreaker and grade does the insert use? This turning insert features the RP7 chipbreaker and the WPP20G coated-carbide grade within the Tiger·tec Gold series to support controlled chip formation and wear resistance. Which geometry and corner radius are provided? The insert has a rhombic 80° geometry, a 1.6 mm corner radius and a 0° negative rake, designed for strong edges and stable cutting in turning operations. What production benefits does this insert offer? The Tiger·tec Gold coating and the WPP20G grade combine to extend tool life, improve process stability and help lower tooling costs per part when used in steel turning applications. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand presentation: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and forms part of the Swedish Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is original, brand-new merchandise from the manufacturer.
CNMG120416-RP7 WPP30G WPP30G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating for longer tool life, the WPP30G grade optimised for steel, and the RP7 chipbreaker for dependable chip control — order the insert directly via Metav Werkzeuge or consult our specialists if necessary. CNMG120416-RP7 WPP30G Walter Tools — CNMG turning indexable insert, Tiger·tec Gold coated CNMG120416-RP7 WPP30G is a rhombic 80° indexable turning insert designed for efficient steel machining with a robust RP7 chipbreaker Tiger·tec Gold coating for extended tool life WPP30G grade optimised for steel machining RP7 chipbreaker for consistent chip control Rhombic 80° CNMG form with 1.6 mm radius Reliable performance for steel turning The combination of the WPP30G carbide grade and the Tiger·tec Gold coating delivers a balanced performance for general steel machining. The grade is engineered to cope with the typical heat generation and chip formation encountered when cutting steel, which results in stable cutting conditions and reduced edge wear. For production environments that require consistent results across a range of steels, this coated carbide solution offers predictable tool life and fewer insert changes, supporting uninterrupted machining cycles. Better surface finish and predictable chips The engineered RP7 chipbreaker promotes reliable chip control and helps to avoid irregular swarf that can interrupt production. The insert’s rhombic 80° geometry and 1.6 mm corner radius support a secure seating and allow for both medium finishing and light roughing passes. By controlling chip shape and evacuation, the tool supports improved surface quality and reduces secondary operations, which in turn lowers process time and handling effort. Cost-effective machining and process security Optimising the indexable system around a versatile grade like WPP30G reduces the number of special inserts required across a diverse parts mix. The coated grade’s wear resistance and the insert’s robust geometry contribute to higher productivity and predictable change intervals. In practice, this means fewer tool changes, less downtime and an improved cost-per-part metric — tangible benefits for batch and continuous production alike. Practical application and compatibility The insert is supplied in the common CNMG format and is intended primarily for steel applications as defined by ISO P groups. Its negative 0° rake setting supports stable cutting in heavier engagement and when chip control is a priority. As an indexable turning insert with the CNMG designation, it is compatible with a wide range of standard toolholders designed for CNMG profiles, enabling straightforward integration into existing turning setups without the need for special adapters. For orders or technical advice on the Walter Tools CNMG120416-RP7 WPP30G turning insert, please contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by telephone on +49 2822 7131930 — our specialists will assist with application recommendations and availability. Technical data SKU: CNMG120416-RP7-WPP30G-WALTER Designation: CNMG120416-RP7 WPP30G Label: Drehwendeschneidplatte CNMG120416-RP7 WPP30G Walter Tools Manufacturer: Walter Tools Dimensions & measurable data Plate size: 12 Corner radius: 1.6 mm Plate form: Rhombus 80° Plate thickness: 04 Tolerance class: M Rake/clearance: 0° (negative) Materials & special features Series: Tiger·tec Gold Grade: WPP30G (coated carbide) Chipbreaker: RP7 Execution: G Suitable material group: P (steel) Product type: Indexable turning insert (CNMG) FAQ What materials is this insert best suited for? The CNMG120416-RP7 WPP30G is optimised for ISO P materials, specifically a range of steels, and is designed to manage the typical heat and chip formation encountered in steel turning. How does the RP7 chipbreaker benefit production? The RP7 chipbreaker on this Walter Tools insert shapes and breaks chips reliably, reducing swarf handling and improving process stability during medium to light turning operations. Can the CNMG form be used in existing holders? Yes, the CNMG geometry is a standard indexable format; the insert fits toolholders designed for CNMG profiles, allowing easy integration into common turning tool systems. What does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating enhances wear resistance and thermal stability, extending edge life and maintaining cutting performance across varying steel grades. Is the corner radius suitable for finishing? The 1.6 mm corner radius offers a compromise between edge strength and surface quality, supporting light finishing and robust roughing where a slightly larger radius is acceptable. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
CNMG160608-MK5 WKK10S WKK10S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating and the MK5 chipbreaker for reliable cast‑iron turning and consistent surface quality; the rhombic 80° form and 0.8 mm corner radius provide a stable cutting edge for productive machining. Order directly via Metav Werkzeuge or contact the consultants for application support. CNMG160608-MK5 WKK10S — Tiger‑tec Silver indexable turning insert for cast iron, Walter Tools The CNMG160608-MK5 WKK10S is an indexable turning insert designed for cast‑iron applications, combining a Tiger‑tec Silver coated carbide grade with an MK5 chipbreaker for short, controlled chips in heavy‑duty machining. Tiger‑tec Silver coated carbide MK5 chipbreaker for short chips Rhombic 80° form for robustness Suited for cast iron machining Longer tool life through advanced coating technology The combination of the Tiger‑tec Silver technology and the WKK10S grade produces a wear‑resistant surface that sustains cutting performance under abrasive conditions typical of cast iron. The coated carbide substrate reduces flank wear and improves resistance to thermal and mechanical stresses, which translates into longer tool life and fewer indexings during production. For production planning, this means improved process stability and reduced tool change frequency. Consistent chip control minimises interruptions The MK5 chipbreaker is optimised for broken, short chips commonly produced when turning cast iron. Short, repeatable chips reduce the risk of entanglement and improve evacuation from the cutting zone, which supports uninterrupted machining and safer handling. The controlled chip form also contributes to a more stable cutting temperature and consistent surface finish on the workpiece. Geometry that balances strength and surface quality The rhombic 80° shape with a 0.8 mm corner radius and a negative 0° rake designation offers a robust cutting edge suited to both medium and heavy cuts while delivering reliable dimensional control. The insert geometry favours edge stability and supports fine finishing passes where surface integrity matters. Where higher material removal rates are required, the geometry helps maintain cutting edge integrity under increased loads. Application guidance and process fit Designed for cast‑iron machining in accordance with ISO group K, this indexable insert fits standard CNMG holders and is suitable for a range of turning operations from roughing to finishing when paired with appropriate cutting data. The WKK10S grade provides a balance of abrasion resistance and toughness, making it a practical choice for workshops seeking repeatable results across a variety of cast‑iron components. For tailored cutting parameters, consult Metav Werkzeuge to align insert choice, holder, and machining conditions with production goals. Contact Metav Werkzeuge for application advice and to secure Tiger‑tec Silver inserts for high‑productivity cast‑iron turning Technical data Article number: CNMG160608-MK5-WKK10S-WALTER Designation: CNMG160608-MK5 Full designation: CNMG160608-MK5 WKK10S Facts Size: 16 Thickness code: 06 Corner radius: 0.8 mm Clearance / rake: 0° (negative) Tolerance class: M Special features Series: Tiger‑tec Silver Grade: WKK10S (coated carbide) Chipbreaker: MK5 Plate form: Rhombus 80° Application group: cast iron (ISO K) Execution: G FAQ What materials is this insert intended for? The WKK10S grade and Tiger‑tec Silver coating are tailored for machining cast iron, with the MK5 chipbreaker optimised for short, controlled chips. Which chipbreaker is integrated and why does it matter? The insert uses an MK5 chipbreaker, which promotes short, broken chips ideal for cast‑iron turning and helps maintain process continuity. What does the rhombic 80° form provide in practice? The rhombic 80° geometry offers a strong cutting edge and flexibility for a range of turning tasks, improving stability in both roughing and finishing operations. Is this insert compatible with standard CNMG holders? The designation corresponds to common CNMG standards; compatibility with the toolholder should be verified, and Metav Werkzeuge can confirm fitment and recommend suitable holders. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer. Walter Tools is referenced as the product brand.
CNMG160608-MK5 WKK20S WKK20S Wendeplatten - Walter Tools
High wear resistance and reliable chip control reduce stoppages and extend productive tool life; the Tiger‑tec Silver WKK20S grade together with the MK5 chipbreaker suits abrasive cast iron machining and promotes stable production. Order directly via Metav Werkzeuge or request technical consultation from their advisors for cutting data and process integration. CNMG160608-MK5 WKK20S — Turning indexable insert, Tiger‑tec Silver, Walter Tools The CNMG160608-MK5 WKK20S is a turning insert engineered for productive machining of cast iron, combining a Tiger‑tec Silver coated carbide grade with an MK5 chipformer for consistent short‑chip behaviour. Tiger‑tec Silver coated carbide for wear resistance Optimised MK5 chipbreaker for short chips 0° negative rake for stable cutting Rhombic 80° CNMG shape, 0.8 mm nose radius Consistent productivity through optimised coating and grade The combination of Tiger‑tec Silver coating and the WKK20S grade is aimed at abrasive cast iron machining where predictable edge life matters. Coated carbide provides a wear‑resistant surface layer that reduces abrasive loss and supports repeatable tool life; the grade is balanced to handle the typical short, brittle chips of cast materials as defined for ISO group K. The integrated MK5 chipbreaker is designed to form short, controlled chips, which lowers the risk of chip entanglement and reduces cycle interruptions, resulting in a measurable improvement in process stability and overall throughput. Robust edge geometry for secure cutting and improved surface quality A 0° negative rake and rhombic 80° form give the insert mechanical strength at the cutting edge, which is beneficial in interrupted cuts and heavy engagement scenarios. The 0.8 mm nose radius contributes to a stable cutting contact and helps achieve a better surface finish without compromising edge robustness. In practice, a neutral rake angle shifts load-bearing into the carbide substrate, which increases resistance to chipping and supports consistent dimensional results across production runs. Process advantages that simplify workplace routines The CNMG geometry is compatible with standard toolholders and is intended to deliver operational reliability in serial turning tasks. The MK5 chipformer produces short chips that are easier to evacuate, lowering manual chip handling and the likelihood of machine downtime caused by chip buildup. Insert clamping is straightforward and, when combined with stable fixturing, supports reproducible results. For customers who require detailed cutting parameters for particular machines or cast iron grades, process data can be provided to align machining strategy with shopfloor capabilities. Practical recommendations for optimal use For best results, secure the insert in a rigid holder and ensure stable workpiece clamping to exploit the strength of the cutting edge geometry. Cooling strategy and chip evacuation should be adapted to the component geometry and machine setup; short‑chip formation from the MK5 chipbreaker generally eases the need for aggressive chip control measures. When greater clarity is required on parameter windows or expected tool life for specific cast iron variants, technical consultation is available to tailor the cutting concept and reduce trial time. Contact Metav Werkzeuge for tailored cutting data and integration advice when using Walter Tools Tiger‑tec Silver CNMG inserts and ensure optimal performance in cast iron production. Technical Data SKU: CNMG160608-MK5-WKK20S-WALTER Article: CNMG160608-MK5 WKK20S Manufacturer: Walter Tools Product type: Turning indexable insert Series: Tiger‑tec Silver Grade: WKK20S Tolerance class: M Execution: G Core data Size: 16 mm Thickness: 6 mm Corner radius: 0.8 mm Free angle: 0° (negative) Plate form: Rhombus 80° Chipbreaker: MK5 Special features Coating: Tiger‑tec Silver Material/grade: Coated carbide Application group: Cast iron (ISO K) Shape code: CNMG160608-MK5 Series description: Optimised for abrasive wear and short, breaking chips FAQ Which materials is this insert suitable for? The CNMG160608-MK5 WKK20S turning insert from Walter Tools is optimised for cast iron (ISO group K) and is designed for abrasive cast‑material behaviour. What chip control can be expected with this geometry? The integrated MK5 chipbreaker on the CNMG160608-MK5 WKK20S promotes short, controllable chips, improving evacuation and reducing the risk of chip accumulation. What are the key geometry specifications for machining setup? The insert features a rhombic 80° form with a 0.8 mm nose radius and 0° negative rake, which supports a robust cutting edge and stable machining. Is the insert coated and what benefit does that provide? Yes; the Tiger‑tec Silver coating on the WKK20S grade enhances wear resistance and contributes to longer, more predictable tool life when machining cast iron. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG160608-MM5 WMP20G WMP20G Wendeplatten - Walter Tools
Take advantage of the combination of high productivity, predictable chip control and long tool life provided by the Tiger·tec Gold grade; order directly via Metav Werkzeuge or consult the technical team for application support. CNMG160608-MM5 WMP20G — Rhombic 80° indexable insert for stainless steel, Walter Tools The CNMG160608-MM5 WMP20G is a rhombic 80° indexable turning insert designed for stainless steel machining under medium to robust conditions. Tiger·tec Gold coating for extended tool life MM5 chipbreaker for stable chip formation Rhombic 80° form with 0.8 mm nose radius Optimised for machining stainless steel Consistent cutting performance for stainless steel applications The combination of the WMP20G grade and Tiger·tec Gold coating provides a balance between wear resistance and edge stability when machining stainless steel. The coating system reduces friction and thermal load at the cutting edge, which helps to avoid build-up and maintain dimensional accuracy over longer toolpaths. As a consequence, process reproducibility improves and changeover intervals can be extended without sacrificing surface quality. Geometry that supports precise and robust turning The rhombic 80° geometry and 0.8 mm nose radius ensure a stable cutting edge that is suitable for general-purpose turning as well as for applications requiring occasional heavier cuts. The insert’s negative 0° relief promotes secure seating in the pocket and reduces the risk of chipping under interrupted cuts. This geometry supports repeatable results on turned components and contributes to predictable tool life in batch and single-piece production alike. Stable chip control and predictable tool life The MM5 chipbreaker is engineered to produce short, controllable chips when cutting ductile, heat-resistant alloys common to stainless steel workpieces. Controlled chip formation reduces the likelihood of surface damage and minimises the need for secondary chip management measures. Together with the coated carbide substrate of the grade, this delivers a measurable improvement in cycle stability and a reduction in unscheduled stoppages due to chip-related issues. Simplified integration into existing tool systems The insert designation and dimensions align with widely used toolholder systems, making replacement and inventory management straightforward. The indexable format allows for multiple edge renewals per insert, lowering consumption per metre of cut and supporting lean tooling strategies. For situations requiring process optimisation or specific holder recommendations, the technical consultants at Metav Werkzeuge can provide targeted advice based on the application and machine setup. For tailored application support or to request a delivery proposal for the Walter Tools CNMG160608-MM5 WMP20G, contact Metav Werkzeuge for precise recommendations and rapid processing. Technical Data SKU: CNMG160608-MM5-WMP20G-WALTER Designation: CNMG160608-MM5 WMP20G Product type: Drehwendeschneidplatte Series: Tiger-tec Gold Grade: WMP20G Manufacturer: Walter Tools Facts Insert form: Rhombus 80° Size: 16 Thickness: 06 Corner radius: 0.8 mm Relief/relief angle: 0° (negative) Chipbreaker: MM5 Material group suitability: M (stainless steel) Special features Coating: Tiger·tec Gold Substrate: coated cemented carbide Application focus: rostfreier Stahl Series description: balance of wear resistance and edge stability FAQ What material is this insert best suited for? The CNMG160608-MM5 WMP20G is optimised for machining stainless steel and performs reliably under medium to robust cutting conditions. How does the MM5 chipbreaker affect machining? The MM5 chipbreaker promotes short, controllable chips on ductile stainless alloys, improving surface finish and reducing chip-related interruptions. Is the insert compatible with standard toolholders for CNMG inserts? Yes, the CNMG160608-MM5 form follows common CNMG dimensions and can be used in matching indexable toolholders designed for this geometry. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. The mention of Walter Tools serves explanatory purposes only; there is no affiliation between Metav Werkzeuge and the named manufacturers. The offered item is an original, factory-new product of the manufacturer.
CNMG160608-MM5 WMP20S WMP20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, the WMP20S grade and the MM5 chipbreaker for stable machining of stainless steel; the result is reliable tool life and consistent surface finish in medium to robust turning operations. Order the CNMG160608-MM5 WMP20S turning insert directly via Metav Werkzeuge or consult the technical team for application recommendations. CNMG160608-MM5 WMP20S turning insert – Tiger·tec Silver, optimised for stainless steel (Walter Tools) CNMG160608-MM5 WMP20S is a rhombic 80° turning insert designed for reliable performance in stainless steel machining and medium to robust cutting conditions Tiger·tec Silver coated WMP20S grade Optimised for stainless steel machining Rhombic 80° shape with 0.8 mm radius MM5 chipbreaker for stable chip control Consistent performance on stainless steel with reduced built-up edge The Tiger·tec Silver coating in combination with the WMP20S carbide composition provides a balanced wear resistance and toughness that is particularly suited to stainless steel. Coated carbide grades reduce adhesion and heat-related damage that commonly cause built-up edge and premature flank wear. This turning insert therefore supports longer operating intervals and less frequent tool changes, which translates into higher machine uptime and more predictable process windows. The result is consistent part quality and a lower cost per component in batch and continuous turning operations. Precision geometry for secure chip formation and surface finish The rhombic 80° insert geometry with a 0.8 mm corner radius and 0° (negative) relief angle offers a controlled cutting edge for a variety of turning tasks. The MM5 chipbreaker is designed to promote short, manageable chips under the thermal and mechanical challenges of stainless steel, improving evacuation and reducing the risk of surface damage. This geometry supports stable cutting forces and contributes to reproducible surface roughness values, enabling tighter process control and fewer rejects in serial production. Predictable economy and straightforward tool management Belonging to the Tiger·tec Silver series, this insert integrates into standard Walter Tools toolholders and grade families, simplifying inventory and tool selection. The cartridge-style designation and ISO-compatible form make tool changes fast and error-free, supporting lean workshop workflows. For operations requiring repeatable performance in medium to robust conditions, the combination of coating, chipformer and geometry results in measurable reductions in downtime and consistent productivity gains. Metav Werkzeuge can provide application data and run recommendations for seamless integration into existing turning processes. Discuss application-specific recommendations and availability of Walter Tools Tiger·tec Silver inserts with Metav Werkzeuge at info@metav-werkzeuge.com or by phone on +49 2822 7131930 to ensure optimal selection and process setup Technical data SKU: CNMG160608-MM5-WMP20S-WALTER Designation: CNMG160608-MM5 WMP20S Product type: Turning insert Series: Tiger·tec Silver Grade: WMP20S Manufacturer: Walter Tools Shape: Rhombus 80° Chipbreaker: MM5 Facts Corner radius: 0.8 mm Relief angle: 0° (negative) Insert size: 16 Thickness code: 06 Special features Coating technology: Tiger·tec Silver (coated carbide) Material suitability: stainless steel Application class: medium to robust cutting conditions Stable cutting edge and controlled chip formation FAQ What materials is this insert best suited for? The CNMG160608-MM5 WMP20S turning insert from Walter Tools is optimised for stainless steel and performs reliably under medium to robust cutting conditions. How does the MM5 chipbreaker affect machining? The MM5 chipbreaker on the CNMG160608-MM5 WMP20S promotes short, controllable chips and supports stable chip evacuation when machining stainless steel, improving surface quality. Is this insert compatible with standard toolholders? Yes, the insert follows ISO-compatible geometry for rhombic 80° turning inserts and fits common Walter Tools toolholders designed for CNMG-style inserts. What advantage does Tiger·tec Silver provide? Tiger·tec Silver coating increases wear resistance while maintaining toughness, which helps to reduce built-up edge and extend the service life of the CNMG160608-MM5 WMP20S in stainless steel applications. Where to get application support or order this insert? Metav Werkzeuge can supply technical guidance and availability information for the CNMG160608-MM5 WMP20S; contact info@metav-werkzeuge.com or call +49 2822 7131930 for tailored advice. Hersteller: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG160608-MM5 WSM10S WSM10S Wendeplatten - Walter Tools
The combination of a Tiger·tec Silver coating and a specialist WSM10S grade delivers stable edge life and secure chip formation when turning high-strength alloys; the rhombic 80° geometry with a 0.8 mm corner radius ensures predictable surface quality and repeatable performance. Order the CNMG160608-MM5 WSM10S insert directly via Metav Werkzeuge or ask the consultants for material-specific recommendations. CNMG160608-MM5 WSM10S Indexable turning insert – Walter Tools, Tiger·tec Silver, for stainless steel and superalloys The CNMG160608-MM5 WSM10S is an 80° rhombic indexable insert optimised for stable machining of stainless steels (M) and heat-resistant superalloys/titanium (S) in demanding turning applications. Tiger·tec Silver coating for edge stability Suitable for stainless steels and superalloys Rhombic 80° form with negative 0° rake 0.8 mm corner radius for controlled chip formation Longer tool life through optimised coating technology The high-performance Tiger·tec Silver system combined with the WSM10S grade provides a balance between thermal resistance and toughness, reducing flank wear under high temperatures. This coated carbide formulation is intended to maintain a stable cutting edge when machining demanding materials, which translates into fewer insert changes and more consistent component quality. The described coating technology supports productive machining cycles and helps to avoid premature edge breakdown in continuous operations. Predictable chip control and improved surface finish The MM5 chipbreaker together with a 0.8 mm corner radius and the negative 0° rake angle promotes secure chip formation on tough-to-machine materials. The geometry controls chip flow and minimises the risk of built-up edge, which is a common cause of poor surface finish on stainless steels and superalloys. As a result, the insert helps to deliver consistent component appearance and dimensional stability, reducing the need for secondary operations. Robust geometry for versatile turning programmes The rhombic 80° form with an insert size of 16 and thickness designation 06 provides a versatile platform compatible with standard CNMG toolholders. This configuration enables productive turning across different feed and depth-of-cut ranges while offering good access in internal and external turning setups. The insert’s tolerance class M and execution G ensure repeatable seating and clamping, supporting reliable tool change intervals and predictable process behaviour. Application guidance for demanding materials and process stability Designed for stainless steel (ISO group M) and heat-resistant alloys or titanium (ISO group S), the grade supports machining scenarios where heat management and edge stability are critical. The insert’s combination of geometry and coating assists in preventing thermal softening and supports stable chip evacuation under medium to heavy cut conditions. For specific cutting data and optimal toolholder recommendations, refer to Metav Werkzeuge’s process guidelines to match feeds, speeds and coolant strategy to the component material. For machining stainless steels and superalloys, select Walter Tools’ Tiger·tec Silver WSM10S grade—contact Metav Werkzeuge for tailored cutting data and ordering assistance. Technical data SKU: CNMG160608-MM5-WSM10S-WALTER Article designation: CNMG160608-MM5 WSM10S Type: Indexable turning insert Manufacturer: Walter Tools Core specifications Insert size: 16 Thickness: 06 Corner radius: 0.8 mm Clearance / rake angle: 0° (negative) Form: Rhombic 80° Chipbreaker: MM5 Materials & features Grade / coating: WSM10S, Tiger·tec Silver coated carbide Suitable for: stainless steel (M), superalloys / titanium (S) Tolerance class: M Execution: G FAQ Which materials is this insert suitable for? The CNMG160608-MM5 WSM10S insert is specified for stainless steel (ISO group M) and for heat-resistant superalloys and titanium (ISO group S), where thermal resistance and edge stability are required. What advantages does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating increases thermal resistance and wear protection while maintaining toughness, which helps the insert deliver longer life and consistent cutting-edge behaviour on demanding materials. How does the MM5 chipbreaker affect turning performance? The MM5 chipbreaker is designed to produce manageable chips and reduce the tendency for built-up edge, supporting improved surface finish and process stability when cutting stainless steels and superalloys. Why choose a rhombic 80° CNMG geometry? The rhombic 80° form offers a good compromise between strength and accessibility, enabling effective external and internal turning with reliable insert seating and repeatable results. What is the benefit of the 0.8 mm corner radius? A 0.8 mm corner radius provides robust edge support for interrupted cuts and higher feed rates while still enabling an acceptable surface finish on components made from tough-to-machine alloys. Manufacturer: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG160608-MM5 WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the MM5 chipbreaker for reliable machining of stainless steels and heat‑resistant alloys; the result is stable chip formation and extended tool life. Order the insert directly via Metav Werkzeuge or consult the technical team for cutting data and toolholder recommendations. CNMG160608-MM5 WSM20S turning indexable insert — 0.8 mm nose radius, Rhombic 80° (Walter Tools) CNMG160608-MM5 WSM20S is a Rhombic 80° turning indexable insert designed for heavy-duty finishing and semi‑finishing of stainless steels and heat‑resistant superalloys, featuring a negative 0° rake for stable cutting conditions Tiger·tec Silver coated grade WSM20S Robust MM5 chipbreaker for secure chip control Negative 0° rake for high process stability 0.8 mm nose radius, Rhombic 80° form High process security for demanding materials The CNMG160608‑MM5 WSM20S insert combines the Tiger·tec Silver coating with a specially developed carbide grade to deliver consistent wear resistance under thermal and mechanical load. The coating reduces friction and supports elevated cutting temperatures, which is particularly beneficial when turning stainless steels and superalloys that tend to harden at the cutting edge. With the negative 0° rake geometry, the insert favours a stable cutting action and lowers the risk of built‑up edge formation, translating into fewer interruptions and more predictable cycle times. Reliable chip control that protects the tool and workpiece Equipped with the MM5 chipbreaker and a 0.8 mm nose radius, this insert promotes controlled chip segmentation and evacuation. Controlled chips reduce tool‑holder vibration and help to protect the machined surface, producing a reproducible finish even in challenging alloys. The Rhombic 80° shape ensures versatile engagement angles for a range of turning operations, while the chipbreaker geometry assists in maintaining a constant cutting force—this yields a tangible improvement in process reliability and component quality. Economic advantages through durability and repeatability Investing in a coated, application‑focused grade such as WSM20S provides a cost‑effective route to longer tool life and fewer indexings. The combination of coating technology and substrate metallurgy in this series results in steady flank wear behaviour, which aids predictable tool change schedules and reduces scrap rates. For production environments where repeatability and uptime matter, the insert supports shorter setup cycles and more consistent part tolerances, improving overall throughput and lowering unit costs. Practical application and machine integration The insert is suitable for tools compatible with the CNMG geometry and is recommended for operations that prioritise surface integrity and dimensional stability. It addresses ISO groups M (stainless steels) and S (heat‑resistant superalloys and titanium) as primary application areas, providing a versatile solution for both aerospace and energy sector components. For optimal results, pair the insert with a rigid toolholder and an appropriate coolant strategy; cutting data should be adapted to machine stiffness and workpiece characteristics. Contact Metav Werkzeuge for tailored cutting data, toolholder matching and rapid supply of the CNMG160608‑MM5 WSM20S insert to suit specific production needs Technical data Article number: CNMG160608-MM5-WSM20S-WALTER Designation: CNMG160608-MM5 WSM20S Product type: Turning indexable insert (Drehwendeschneidplatte) Brand: Walter Tools Series: Tiger‑tec Silver Core data Nose radius: 0.8 mm Insert size: 16 (wpl_plattengroe: 16) Thickness: 06 Relief angle: 0° (negative) Tolerance class: M Special features Grade: WSM20S (Tiger·tec Silver coated carbide) Chipbreaker: MM5 Shape: Rhombic 80° Substrate/application: S / M (heat‑resistant superalloys / stainless steels) Execution: G Base designation: CNMG160608-MM5 FAQ What materials is this insert best suited for? The CNMG160608‑MM5 WSM20S insert is designed primarily for stainless steels (ISO M) and heat‑resistant superalloys/titanium (ISO S), where thermal stability and secure chip control are required. How does the Tiger·tec Silver coating benefit machining? The Tiger·tec Silver coating on the WSM20S grade reduces friction and improves thermal resistance, which prolongs tool life and stabilises cutting conditions in difficult‑to‑cut materials. What is the purpose of the MM5 chipbreaker? The MM5 chipbreaker provides controlled chip segmentation and evacuation, lowering vibration and protecting both the tool and the workpiece finish during turning operations. Can the insert be used for finishing and semi‑finishing? Yes, the Rhombic 80° geometry and the 0.8 mm nose radius make this insert suitable for both finishing and semi‑finishing tasks, offering a balance between strength and surface quality. Is the negative 0° rake suitable for heavy interrupted cuts? The negative 0° rake increases edge strength and is advantageous for stable performance under high cutting forces and mild interruptions, improving process security. Manufacturer: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. The mention of brand names serves explanatory purposes only and does not indicate any affiliation. The offered article is original, brand‑new merchandise from the manufacturer.
CNMG160608-MM5 WSM30S MM5 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver wear resistance and the WSM30S grade for stable chip formation in demanding materials; the robust MM5 chipbreaker and rhombic 80° geometry support consistent production performance—order directly via Metav Werkzeuge or consult our specialists for application advice. CNMG160608-MM5 WSM30S indexable turning insert, Tiger·tec Silver coating, Walter Tools CNMG160608-MM5 WSM30S is an indexable turning insert designed for turning applications in stainless steels and heat-resistant superalloys, offering a balance of edge stability and controlled chip formation Tiger·tec Silver coating for wear resistance Optimised MM5 chipbreaker for stable chips Suitable for stainless steels and superalloys Rhombus 80° CNMG 16 mm format High wear resistance for long tool life in difficult alloys The coated carbide WSM30S grade, part of the Tiger·tec Silver series, combines a wear-resistant surface with a substrate engineered for thermal stability. This results in improved flank and crater wear behaviour, which extends useful tool life when machining materials that challenge cutting edges. For workshop planners and production engineers, this means fewer indexings and longer uninterrupted cutting times, translating into measurable reductions in tool-change frequency and enhanced machine utilisation. The coating technology also supports higher cutting speeds where process stability permits, without compromising the integrity of the cutting edge. Stable cutting geometry that improves process reliability The rhombic 80° CNMG form and the 0.8 mm corner radius deliver a robust contact geometry that resists chipping and provides consistent surface finish in semi-finishing and finishing operations. The insert features a negative 0° clearance design, which enhances edge strength under heavy engagement. Combined with the MM5 chipbreaker, the geometry promotes predictable chip breaking and evacuation, reducing the risk of built-up edge and improving dimensional repeatability. For applications where repeatable results are critical, this insert supports stable machining windows and simplifies process documentation. Optimised for ISO M and S materials to increase productivity This turning grade is specified for ISO groups M (stainless steels) and S (heat-resistant superalloys and titanium), addressing the typical problems of poor thermal conductivity and high ductility. The WSM30S composition and the insert’s geometry help to maintain a secure chip formation even under elevated temperatures, which benefits throughput when machining challenging workpiece materials. Integrating this insert into a cutting strategy can lead to higher component consistency and reduced scrap rates. Compatibility with standard tool holders means straightforward adoption into existing tool setups without additional fixtures. Practical advantages for production environments The insert’s dimensions and indexable nature make it suitable for rapid tool replacement and straightforward inventory handling. The 16 mm size and standard CNMG160608-MM5 designation allow rapid identification and compatibility with common turning toolholders, reducing preparation time at the machine. In addition, the combination of coating, chipbreaker and geometry contributes to lower machining variability, supporting smoother downstream operations such as inspection and assembly. For production managers, these attributes contribute to predictable cycle times and easier process optimisation. Contact Metav Werkzeuge for tailored cutting recommendations on Walter Tools Tiger·tec Silver inserts, request detailed cutting data for the CNMG160608-MM5 WSM30S, or arrange a materials assessment through Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: CNMG160608-MM5-WSM30S-WALTER Designation: CNMG160608-MM5 WSM30S Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WSM30S Data Geometry: Rhombus 80° (CNMG) Size: 16 Thickness: 06 Corner radius: 0.8 mm Clearance angle: 0° (negative) Chipbreaker: MM5 Tolerance class: M Special features Coating: Tiger·tec Silver Material suitability: S / M (superalloys, stainless steels) Application focus: Turning, semi-finishing/finishing Indexable insert type: CNMG with MM5 chip control FAQ What materials is this insert best suited for? The CNMG160608-MM5 WSM30S insert from Walter Tools is optimised for ISO M (stainless steels) and ISO S (heat-resistant superalloys and titanium), providing secure chip formation and wear resistance in these groups. How does the MM5 chipbreaker affect machining? The MM5 chipbreaker on the CNMG160608-MM5 WSM30S promotes predictable chip segmentation and evacuation, which reduces the risk of built-up edge and improves surface finish during turning operations. Can this insert be used for semi-finishing and finishing? Yes, the combination of a 0.8 mm corner radius, rhombic 80° geometry and the WSM30S grade makes this insert suitable for both semi-finishing and finishing passes where edge stability and surface quality are required. Is the CNMG160608-MM5 compatible with standard toolholders? The CNMG form and the 16 mm format follow common industry standards, allowing straightforward mounting in compatible turning toolholders without the need for special adaptors. What process benefits does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating on the WSM30S grade enhances wear resistance and thermal stability, enabling longer tool life and more consistent cutting performance when machining demanding alloys. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG160608-MP5 WPP10G Wendeplatten - Walter Tools
The combination of the Tiger·tec Gold WPP10G grade and the MP5 chipbreaker delivers stable chip control and predictable tool life for steel turning; the rhombic 80° geometry with a 0.8 mm corner radius and 0° negative clearance supports consistent surface finish and reduced vibration. Order the insert directly via Metav Werkzeuge or consult their specialists for tailored cutting data and application advice. CNMG160608-MP5 WPP10G — Rhombic 80° turning insert, Tiger·tec Gold, Walter Tools The CNMG160608-MP5 WPP10G is a rhombic 80° coated turning insert designed for steel applications, optimised for reliable chip control and extended tool life. Rhombic 80° geometry for versatile turning Tiger·tec Gold coating WPP10G for wear resistance MP5 chipbreaker for consistent chip control 0.8 mm corner radius with 0° negative clearance Consistent productivity for steel machining The Tiger·tec Gold WPP10G grade is a coated carbide developed for machining steels (ISO group P). Its combination of a wear-resistant coating and a robust substrate reduces tool changes and increases process uptime. The coated grade is particularly effective where typical heat generation and continuous chip formation occur during steel turning. For operations seeking predictable tool life, the grade’s balance of abrasion resistance and toughness provides a favourable cost-per-component metric while maintaining dimensional stability. Better surface quality through controlled chip formation The MP5 chipbreaker paired with the rhombic 80° geometry is designed to produce short, manageable chips and a steady cutting force. The 0° negative clearance gives a stable cutting edge orientation that helps to reduce vibration at moderate to heavy depths of cut, resulting in improved surface finish. For operators unfamiliar with chipbreaker function: the MP5 profile shapes chip flow at the insert face so that material is evacuated reliably, reducing the risk of built-up edge and minimising interruptions in automated turning cycles. Easy integration and predictable set-up The insert’s dimensional series and tolerance class (M) facilitate straightforward mounting in common CNMG toolholders and indexable tool systems, simplifying stock management. Key measurable characteristics such as the 0.8 mm corner radius and the 16 inscribed circle size allow quick selection of feeds and depths of cut for both roughing and finishing steps. The geometry and grade combination supports flexible application, from general-purpose steel turning to more demanding production environments where repeatability and process security are required. Contact Metav Werkzeuge for availability, cutting-parameter support and application-specific advice for the Walter Tools CNMG160608-MP5 WPP10G; eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: CNMG160608-MP5-WPP10G-WALTER Item designation: CNMG160608-MP5 WPP10G Product type: Turning insert (indexable) Manufacturer: Walter Tools Series: Tiger·tec Gold Grade: WPP10G Chipbreaker: MP5 Core specifications Inscribed circle / size: 16 Thickness: 06 Corner radius: 0.8 mm Clearance angle: 0° (negative) Tolerance class: M Special features Coating: Tiger·tec Gold (WPP10G) Substrate: coated carbide Geometry: Rhombic 80° Intended material group: Steel (ISO P) FAQ Which materials are suitable for this insert? The CNMG160608-MP5 WPP10G from Walter Tools is specified for steel machining (ISO P), with the WPP10G grade optimised for the heat and chip characteristics typical of unalloyed and alloyed steels. What is the advantage of the MP5 chipbreaker? The MP5 chipbreaker on the CNMG160608-MP5 WPP10G promotes consistent chip control and reliable evacuation, improving process stability and surface finish during turning operations. Is this insert suitable for both roughing and finishing? Yes; the rhombic 80° geometry combined with a 0.8 mm corner radius offers versatility that suits both roughing and medium finishing tasks when the appropriate feeds and speeds are applied. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered article is an original, factory-new product of the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
CNMG160608-MP5 WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coated carbide, the MP5 chipbreaker and robust rhombic geometry for consistent, productive steel turning; order the inserts directly via Metav Werkzeuge or request advice from our technical consultants. CNMG160608-MP5 WPP20G Turning Insert — MP5 chipbreaker, Tiger‑tec Gold (Walter Tools) The CNMG160608-MP5 WPP20G is a rhombic 80° turning insert designed for steel machining, offering a coated carbide grade optimised for reliable chip control and long tool life. Tiger‑tec Gold coated carbide for wear resistance MP5 chipbreaker for controlled chip formation Rhombic 80° geometry for versatile turning 0.8 mm corner radius and 0° negative clearance Increased productivity through a wear‑resistant grade The WPP20G grade, based on Tiger‑tec Gold technology, combines a coated carbide substrate with a wear-resistant surface that is especially suited to machining steel (ISO P). This results in a predictable tool life under typical cutting conditions and reduces the need for frequent index changes. The economic advantage is realised through longer intervals between tool changes and more consistent part quality, so cycle times and scrap rates are improved without complex process changes. Predictable chip control and secure cutting performance Equipped with the MP5 chipbreaker, the insert delivers controlled chip formation that supports stable cutting forces and safer swarf evacuation. The combination of chip geometry and the 0.8 mm corner radius offers a balance between edge strength and surface finish; the relatively small corner radius reduces cutting forces while still providing sufficient edge robustness for general turning tasks. This makes the insert suitable for a broad range of finishing and light to medium roughing operations in steel. Geometry and angles that simplify process planning The rhombic 80° form and 0° negative clearance make the insert compatible with common turning toolholders and applications that require an economical insert shape with good reach and accessibility. The negative clearance reduces the risk of edge chipping in interrupted cuts and heavy engagement, while the 80° point angle allows effective lateral clearance. Together these characteristics reduce the number of special tools required and streamline tooling inventories for workshop planners. Clear specification for integration into production Key specifications such as insert size 16 mm, thickness 6 mm and tolerance class M make process data entry and tool management straightforward. The designation CNMG160608‑MP5 WPP20G identifies the geometry, thickness and chipbreaker at a glance, simplifying procurement and tool assortment. When replacing inserts, matching the MP5 chipbreaker and Tiger‑tec Gold grade ensures continuity of cutting performance and surface quality across batches. Contact Metav Werkzeuge today to specify Tiger‑tec Gold WPP20G inserts for improved turning productivity and arrange a technical consultation via Metav Werkzeuge. Technical data Article number: CNMG160608-MP5-WPP20G-WALTER Designation: CNMG160608-MP5 WPP20G Product type: Turning insert Series: Tiger‑tec Gold Facts Insert size: 16 mm Thickness: 6 mm Corner radius: 0.8 mm Clearance angle: 0° (negative) Insert geometry: Rhombic 80° Tolerance class: M Special features Coating technology: Tiger‑tec Gold Grade: WPP20G (coated carbide) Chipbreaker: MP5 Material application: Steel (ISO P) Execution: G FAQ What materials is this insert intended for? The CNMG160608‑MP5 WPP20G insert is specified for machining steel (ISO P); the WPP20G grade is optimised for the temperatures and chip formation typical of steel turning. What does the MP5 chipbreaker provide in practice? The MP5 chipbreaker ensures controlled chip formation and improved swarf handling, which supports stable cutting forces and safer machining when using the CNMG160608‑MP5 WPP20G. How does the 0.8 mm corner radius affect cutting? A 0.8 mm corner radius increases edge strength compared with finer radii, helping to resist edge chipping while still allowing good surface finish in finishing and light roughing passes with the CNMG160608‑MP5 WPP20G. Is the rhombic 80° shape compatible with standard toolholders? Yes, the rhombic 80° geometry is widely supported by standard turning holders and provides good accessibility for external and some internal turning tasks when using this insert. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trademarks and trade names are the property of their respective owners. Brand names and protected designations are used for explanation only. There is no affiliation between our company and the mentioned brands. The offered item is an original, factory‑new product from the manufacturer (Walter Tools).
CNMG160608-MP5 WPP30G Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Gold coating and the MP5 chipbreaker: durable edge performance and controlled chip formation for steel turning. Fast replacement and predictable results support efficient batch production — order directly via Metav Werkzeuge or contact our consultants for tailored cutting data. CNMG160608-MP5 WPP30G Turning insert for Steel — CNMG160608-MP5 WPP30G (Walter Tools) A CNMG160608-MP5 WPP30G indexable turning insert engineered for reliable general-duty steel machining with a Tiger·tec Gold coating and MP5 chip control Tiger·tec Gold coated grade WPP30G MP5 chipbreaker for stable chip control Rhombic 80° CNMG geometry for versatile turning Negative rake 0° for robust cutting edge Improved tool life and predictable productivity with Tiger·tec Gold The Tiger·tec Gold technology in this insert provides a coated hardmetal surface that reduces flank wear and extends cutting edge life when machining steel (ISO P). The WPP30G grade balances hardness and toughness: it resists abrasive wear while maintaining edge stability in common turning operations. For production contexts where cycle time and repeatability matter, this coating-grade combination lowers downtime and contributes to a predictable tool-change schedule, which helps to optimise overall process efficiency. Process security through consistent chip control and geometry The MP5 chipbreaker is designed to produce short, controlled chips during longitudinal and light profiling cuts, improving evacuation and reducing risk to the machined surface. The rhombic 80° (CNMG) form allows comfortable access for a wide range of turning tasks while the 0° (negative) rake angle adds mechanical strength to the cutting edge. A corner radius of 0.8 mm supports steady dimensional control and contributes to a consistent surface finish, particularly on medium-duty steel components in serial production. Practical handling, inventory clarity and application scope Marked as CNMG160608-MP5 WPP30G, the insert follows common ISO designation logic and fits standard CNMG toolholders, simplifying tool management. The thickness and size designations are suited to robust clamping and stable machining, while the tolerance class M ensures consistent interchangeability between inserts. As a grade optimised for steel, the insert is suitable for unalloyed and alloyed steels where balanced wear resistance and toughness are required. This makes it a pragmatic choice for workshop managers and production engineers seeking dependable, repeatable turning performance. Choose the Walter Tools Tiger·tec Gold CNMG160608-MP5 WPP30G for longer tool life and reliable chip control — contact Metav Werkzeuge for cutting-parameter advice and production support via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: CNMG160608-MP5-WPP30G-WALTER Designation: CNMG160608-MP5 WPP30G Series: Tiger-tec Gold Grade: WPP30G Core data Shape: Rhombus 80° (CNMG) Corner radius: 0.8 mm Size designation: 16 Thickness designation: 06 Free angle: 0° (negative) Tolerance class: M Special features Chipbreaker: MP5 Material application: Steel (ISO P) Execution: G Material type: coated hardmetal FAQ What materials is this insert intended for? The CNMG160608-MP5 WPP30G is optimised for steel (ISO P) applications; the WPP30G grade and Tiger·tec Gold coating are tuned for the heat and chip formation typical of steel turning. How does the MP5 chipbreaker affect machining? The MP5 chipbreaker produces short, controllable chips that improve chip evacuation and reduce risks to surface quality when turning steel with the CNMG160608-MP5 insert. What does WPP30G indicate? WPP30G is the Walter Tools wear grade within the Tiger·tec Gold family; it denotes a coated hardmetal formulation aimed at a balance between wear resistance and toughness for steel machining. Is the rhombic CNMG geometry suitable for profiling? Yes, the rhombic 80° CNMG form offers versatility for both general turning and light profiling operations while maintaining access and clearance in most standard holders. Does the insert require special holders? The CNMG160608-MP5 WPP30G fits conventional CNMG toolholders; ensure the holder supports the insert thickness and negative rake configuration for stable clamping. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Trademarks and trade names are mentioned for explanation only and do not imply any affiliation with our company. The offered article is an original, factory-new product from the respective manufacturer (Walter Tools).
CNMG160608-RM5 WMP20G WMP20G Wendeplatten - Walter Tools
Take advantage of the combination of reliable edge life, Tiger·tec Gold coating and the Rhombic 80° geometry for consistent stainless steel turning; order via Metav Werkzeuge or consult our specialists for application advice. CNMG160608-RM5 WMP20G — indexable turning insert, Tiger·tec Gold, for stainless steels (Walter Tools) The CNMG160608-RM5 WMP20G is an indexable turning insert developed for medium to robust machining of stainless steels, offering a negative relief and a chipbreaker optimised for secure chip formation. Tiger·tec Gold coating for durable cutting Optimised for stainless steels (ISO M) Rhombic 80° form with 0.8 mm corner radius RM5 chipbreaker for stable chip control Dependable performance on stainless steels for fewer interruptions The CNMG160608-RM5 WMP20G insert combines a Tiger·tec Gold coated carbide grade with a geometry tailored to ISO group M materials, delivering stable cutting edges and reduced tendency for built-up edge during longer runs. The negative 0° relief and the RM5 chipbreaker support secure chip formation even under tougher conditions, which helps to maintain cycle times and reduces scrap. This design is particularly suited to suppliers and job shops that require consistent part quality in challenging stainless-steel turning operations. Predictable chip control and extended tool life for productive shops With a 0.8 mm corner radius and the Rhombic 80° form, the insert ensures reliable strength at the cutting edge while allowing flexible feed rates. The RM5 chipbreaker is configured to break and evacuate chips efficiently, lowering the risk of entanglement and improving surface finish. These characteristics translate into fewer tool changes and increased machine uptime, which supports economic machining and predictable batch production. Practical geometry and specifications for versatile turning tasks The combination of the Rhombic 80° geometry, a plate thickness of 06 and an inscribed circle size of 16 makes the insert adaptable to a wide range of turning setups and toolholders. The negative relief supports heavier engagement and roughing passes, while the coated grade reduces friction and enhances wear resistance. For process planning, the insert’s features allow straightforward parameter selection for common stainless steel alloys, helping engineers to achieve repeatable results with minimal trial-and-error. If further application data or cutting parameters are required, Metav Werkzeuge’s technical team is available by e‑mail at info@metav-werkzeuge.com or by telephone at +49 2822 7131930. Contact Metav Werkzeuge today to discuss machining trials, request cutting data or obtain a tailored quotation for the Walter Tools Tiger·tec Gold CNMG160608-RM5 WMP20G insert. Technical data SKU: CNMG160608-RM5-WMP20G-WALTER Label: Drehwendeschneidplatte CNMG160608-RM5 WMP20G Walter Tools Manufacturer: Walter Tools Product type: Indexable turning insert Core specifications Inscribed circle size: 16 Thickness: 06 Corner radius: 0.8 mm Relief angle: 0° (negative) Geometry: Rhombic 80° Features & applications Coating / technology: Tiger·tec Gold Grade / sort: WMP20G Chipbreaker: RM5 Series: Tiger-tec Gold Tolerance class: M Execution: G Material suitability: stainless steels (ISO M) FAQ What materials is this insert best suited for? The CNMG160608-RM5 WMP20G insert is designed primarily for stainless steels (ISO group M), offering secure chip formation and edge stability under medium to robust cutting conditions. How does the Tiger·tec Gold coating benefit machining? The Tiger·tec Gold coating on the CNMG160608-RM5 WMP20G reduces friction and improves wear resistance, which contributes to longer tool life and more consistent surface finishes in stainless-steel turning. What is the purpose of the RM5 chipbreaker? The RM5 chipbreaker on this insert promotes controlled chip segmentation and evacuation, decreasing the likelihood of chip re-cutting and supporting reliable production cycles. Can this insert be used for finishing passes? Yes; owing to the Rhombic 80° form and the 0.8 mm corner radius, the insert can be employed for a range of operations from roughing to semi-finishing, with parameter adjustments to suit the required surface quality. Is the CNMG160608-RM5 compatible with standard toolholders? The CNMG160608-RM5 WMP20G follows common indexable insert dimensions (inscribed circle 16, thickness 06, Rhombic 80°), making it compatible with standard toolholder systems specified for this insert style. Walter Tools: Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
CNMG160608-RM5 WMP30G WMP30G Wendeplatten - Walter Tools
Benefit from a combination of high wear resistance and stable chip control for consistent stainless-steel turning; the Tiger‑tec Gold grade extends tool life while the RM5 chipbreaker improves process reliability. Order the CNMG160608‑RM5 WMP30G directly via Metav Werkzeuge or consult their specialists for application advice. CNMG160608‑RM5 WMP30G — Turning insert (Rhombic 80°, Tiger‑tec Gold) by Walter Tools The CNMG160608‑RM5 WMP30G is a rhombic 80° turning insert optimised for machining stainless steels under medium to robust cutting conditions. Tiger‑tec Gold coating for long tool life RM5 chipbreaker for reliable chip control Rhombic 80° form with 0.8 mm corner radius Optimised for stainless steels (ISO M) Stronger performance through advanced Tiger‑tec Gold coating The combination of the Tiger‑tec Gold coating and the WMP30G substrate provides improved wear resistance and thermal stability during turning operations. The coated carbide construction suppresses premature flank wear and supports consistent cutting-edge integrity under elevated temperatures typical of machining stainless steels. This results in a predictable tool life, reduced downtime for insert changes and a lower cost per component in serial production. Stable chip control and improved process reliability Equipped with the RM5 chipbreaker, the insert ensures controlled chip formation and evacuation when working with tough, ductile materials. Controlled chips reduce the risk of surface damage and machine interruptions, so component quality and cycle time stability are enhanced. The geometry is engineered to support secure chip flow, which contributes directly to fewer interruptions and higher overall productivity in turning applications. Geometry designed for strength and surface quality The rhombic 80° shape and 0.8 mm corner radius balance edge strength with the ability to achieve good surface finishes. The negative 0° relief (negative insert geometry) increases insert robustness for interrupted cuts or heavier feeds, while the compact plate dimensions maintain accessibility in confined tool pockets. These geometric choices help deliver repeatable results and acceptable surface integrity without sacrificing durability. Application-oriented advantages for production environments As a performance-oriented grade from Walter Tools, this insert is tailored for the ISO M material group and is suitable where secure chip formation and stable cutting edges are required. The combination of coated carbide and optimised chipbreaker makes the insert a practical choice for batch production of corrosion‑resistant alloys and a variety of stainless‑steel types. Consistent edge life and predictable wear patterns facilitate process planning and spare‑part management. For procurement or application support regarding the Tiger‑tec Gold CNMG160608‑RM5 WMP30G turning insert, contact Metav Werkzeuge for technical consultation and ordering assistance via info@metav-werkzeuge.com or +49 2822 7131930 — Metav Werkzeuge can advise on grade selection and availability. Technical Data Article number: CNMG160608-RM5-WMP30G-WALTER Description: Drehwendeschneidplatte CNMG160608-RM5 WMP30G Walter Tools Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WMP30G Core specifications Inscribed circle: 16 Thickness code: 06 Corner radius: 0.8 mm Relief angle: 0° (negative) Form: Rhombus 80° Chipbreaker: RM5 Tolerance class: M Design and special features Coated carbide substrate Optimised for ISO M (stainless steels) Suitable for medium to robust cutting conditions Stable chip formation and improved edge life ISO designation: CNMG160608-RM5 WMP30G FAQ Is this insert suitable for machining stainless steels? Yes. The CNMG160608‑RM5 WMP30G turning insert is optimised for stainless steels (ISO M), offering secure chip formation and thermal stability for medium to robust cutting conditions. What advantages does the Tiger‑tec Gold coating provide? The Tiger‑tec Gold coating on the WMP30G grade increases wear resistance and heat tolerance, which helps maintain cutting‑edge integrity and extend insert life in demanding stainless‑steel turning. How does the RM5 chipbreaker affect machining? The RM5 chipbreaker promotes reliable chip control and evacuation, reducing the likelihood of built‑up edge and improving process stability during continuous and interrupted cuts. What does the negative 0° relief mean for application? A negative 0° relief increases insert robustness for tougher operations and interrupted cuts, delivering greater edge strength while retaining effective material removal and surface quality. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and product names remain the property of their respective owners and are mentioned solely for explanation. The offered item is an original, factory‑new product from the manufacturer.
CNMG160608-RM5 WSM10S RM5 Wendeplatten - Walter Tools
Take advantage of the WSM10S grade and the Tiger·tec Silver coating for consistent chip control and extended tool life; combine robust edge stability with the negative 0° geometry for secure performance in demanding materials. Order original Walter Tools inserts via Metav Werkzeuge or consult the Metav team for application advice. CNMG160608-RM5 WSM10S turning insert — Tiger·tec Silver, negative 0° | Walter Tools CNMG160608-RM5 WSM10S is a precision turning insert for demanding machining of rostfreier Stahl and heat‑resistant alloys Tiger·tec Silver coating for thermal stability RM5 chipbreaker for controlled chip formation Rhombus 80° form for versatile turning operations 0.8 mm corner radius for robust edge strength Improve throughput with heat‑resistant cutting performance The CNMG160608‑RM5 WSM10S insert combines a Tiger·tec Silver coating with a specially developed grade to deliver reliable cutting in materials that generate heat and tend to work‑harden. The coated carbide grade WSM10S is optimised for safe chip formation and consistent edge retention when machining rostfreier Stahl and nickel‑based alloys. This results in fewer tool changes, longer uninterrupted cycles and a measurable increase in productivity on lathes and turning centres. The RM5 chipbreaker contributes to stable chip control, reducing downtime related to chip management and improving surface finish consistency. Robust geometry for repeatable accuracy and tool life A negative relief geometry with a 0° (negative) rake and a 0.8 mm corner radius delivers mechanical strength at the cutting edge, especially under heavy interrupted cuts or when processing tough, heat‑resistant superalloys. The rhombic 80° form offers flexible approach angles for external turning and profiling tasks, while the plate thickness and design maintain clamping stability in standard toolholders. Together, these attributes reduce the risk of edge chipping and support repeatable dimensional accuracy across production batches, which is crucial for quality assurance and minimising scrap rates. Seamless integration into production and inventory The insert’s standard CNMG format and clear designation simplify tool selection and inventory management. As a coated carbide turning grade with the RM5 chipbreaker, it fits established toolholder systems and is suitable for a range of turning operations from finishing to medium‑depth cuts. The combination of grade, coating and geometry supports a cost‑effective machining strategy: fewer tool changes, predictable tool life and improved process security. For machining plans that include rostfreier Stahl or titanium‑alloy components, this insert offers a balanced option between edge stability and thermal resistance. Contact Metav Werkzeuge for tailored recommendations on Walter Tools CNMG160608‑RM5 WSM10S inserts and application support — reach out at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: CNMG160608-RM5-WSM10S-WALTER Article designation: CNMG160608-RM5 WSM10S Product type: Turning insert Brand: Walter Tools Core specifications Inscribed circle: 16 mm Thickness: 6 mm Corner radius: 0.8 mm Relief angle: 0° (negative) Shape: Rhombus 80° Special features Coating: Tiger·tec Silver Grade: WSM10S (coated carbide) Chipbreaker: RM5 Suitable for rostfreier Stahl (M) and superalloys/titanium (S) Execution/geometry code: G Series: Tiger‑tec Silver FAQ Which materials are best suited to this insert? The CNMG160608‑RM5 WSM10S insert is engineered for rostfreier Stahl and heat‑resistant superalloys (ISO groups M and S) thanks to the Tiger·tec Silver coating and WSM10S grade. How does the RM5 chipbreaker affect machining? The RM5 chipbreaker on the CNMG160608‑RM5 promotes controlled chip formation and improved surface finish, supporting reliable turning cycles with fewer interruptions. Is this insert compatible with standard CNMG toolholders? Yes, the CNMG160608 design fits standard CNMG holders; the robust thickness and rhombus 80° form ensure secure clamping and process stability. What benefit does the 0° negative rake provide? A 0° (negative) rake offers enhanced edge strength and resistance to chipping during heavy cuts or interrupted turning, extending usable tool life. Can this insert be used for roughing and finishing? The combination of a 0.8 mm corner radius and the WSM10S grade makes the insert suitable for medium‑to‑finishing operations, providing a balance between robustness and surface quality. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are used here for descriptive purposes only and do not imply any affiliation with or endorsement by the trademark holders. The delivered item is an original, factory‑new product of the named manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com