DCMT11T304-FP4 WKP01G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and the WKP01G grade for extended tool life and consistent chip control; the rhombic 55° geometry with a 0.4 mm corner radius ensures stable cutting and good surface finish. Order the insert directly via Metav Werkzeuge or consult the technical team for application-specific recommendations. DCMT11T304-FP4 WKP01G – Rhombic 55° indexable turning insert, Tiger‑tec Gold for steel & cast iron by Walter Tools The DCMT11T304-FP4 WKP01G is an indexable turning insert designed to deliver reliable performance in steel and cast iron machining, combining a coated carbide grade with a chipbreaker suited to typical production tasks. Tiger‑tec Gold coating for wear resistance Optimised WKP01G grade for steel and cast iron FP4 chipbreaker for reliable chip control Rhombic 55° form with 0.4 mm corner radius Longer runtimes thanks to advanced coating and grade The coated carbide WKP01G grade, part of the Tiger‑tec Gold series, is engineered for high wear resistance and consistent edge stability when machining ISO groups P (steel) and K (cast iron). This coating system improves thermal resistance and reduces abrasive wear, which translates into fewer tool changes and lower cost per component in batch production. The combination of a robust substrate and modern coating chemistry supports consistent performance under varying cutting conditions. Geometry that improves process reliability and surface quality The insert’s rhombic 55° shape and dedicated FP4 chipbreaker deliver controlled chip formation and evacuation, reducing the risk of built-up edge and tool-induced surface defects. A 7° clearance angle and a 0.4 mm corner radius balance strength and finish — the radius supports edge stability on interrupted cuts while the geometry promotes stable cutting forces. These design choices enhance process reliability and contribute to reproducible part quality in serial turning operations. Designed for productivity and reduced downtime By combining an optimised grade with a proven chipbreaker geometry, the insert supports higher productivity through longer tool life and predictable wear behaviour. The T3 plate thickness and tolerance class M ensure mechanical robustness and interchangeability in common toolholders, reducing setup time. For machining environments where consistent output and minimal rework are priorities, this solution helps to keep cycle times low while maintaining target surface characteristics. Compatibility and practical application notes The insert is specified for conventional indexable turning toolholders accepting rhombic 55° plates and is particularly suited to applications where steels and cast irons require balanced wear resistance and chip control. The coated carbide composition and the FP4 chip geometry make it suitable for both roughing and finishing cuts, depending on cutting data. For specific feeds, speeds and toolholder recommendations, consult the technical data supplied by Walter Tools or request tailored parameters from the distributor. For reliable, high‑process security in steel and cast iron turning, specify the Walter Tools Tiger‑tec Gold DCMT11T304‑FP4 WKP01G insert and contact Metav Werkzeuge for precise application advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: DCMT11T304-FP4-WKP01G-WALTER Designation: DCMT11T304-FP4 WKP01G Type: Indexable turning insert Manufacturer: Walter Tools Numeric data Plate size: 11 Form angle: 55° Clearance angle: 7° Corner radius: 0.4 mm Plate thickness: T3 Tolerance class: M Special features Series: Tiger‑tec Gold Grade: WKP01G Chipbreaker: FP4 Coated carbide Applicable material groups: P (steel), K (cast iron) Execution: T FAQ What materials is this insert suitable for? The DCMT11T304‑FP4 WKP01G insert is designed for ISO material groups P and K, meaning it is suitable for machining a wide range of steels and cast irons. How does the Tiger‑tec Gold coating benefit production? Tiger‑tec Gold coating on the WKP01G grade enhances wear resistance and thermal stability, which typically results in longer tool life and more consistent machining performance. Which chipbreaker is fitted and what is its effect? The insert features an FP4 chipbreaker, which provides controlled chip formation and evacuation, supporting stable cutting conditions and improved surface finish. Is the insert compatible with common toolholders for rhombic plates? Yes, the rhombic 55° form and T3 thickness are compatible with standard toolholders designed for 55° indexable plates; tolerance class M supports interchangeability. What role does the 0.4 mm corner radius play? A 0.4 mm corner radius offers a compromise between edge strength and surface finish, helping to maintain edge integrity on intermittent cuts while producing acceptable surface quality. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanation only and do not imply any affiliation between our company and the trademark owners. The offered item is an original, factory‑new product from the manufacturer.
DCMT11T304-FP4 WPP10G FP4 Wendeplatten - Walter Tools
Take advantage of the combination of high process reliability, optimised chip control and long tool life offered by the Tiger·tec Gold grade; the FP4 chipbreaker and 0.4 mm corner radius ensure stable cutting in Stahl and efficient finish turning. Order directly via Metav Werkzeuge or request expert consultation for application-specific recommendations. DCMT11T304-FP4 WPP10G — Indexable turning insert for Stahl, Walter Tools DCMT11T304-FP4 WPP10G is an indexable turning insert designed for versatile finishing and medium-duty turning in Stahl, featuring the FP4 chipbreaker and Tiger·tec Gold coating. Tiger·tec Gold coating for extended life FP4 chipformer for reliable chip control Rhombic 55° geometry for versatile turning 0.4 mm corner radius for precise edge definition High-performance finishing and consistent results The DCMT11T304-FP4 WPP10G insert combines a Tiger·tec Gold coated carbide grade with a finely tuned FP4 chipbreaker to deliver consistent surface quality in turning operations on Stahl. The rhombic 55° geometry provides favourable approach angles for a range of turning tasks, reducing deflection and supporting stable cuts. Because the grade is optimised for the typical heat and chip formation of Stahl, the insert sustains cutting temperatures and wear effectively, which translates into predictable tool life and repeatable part quality. Controlled chip formation for process security Reliable chip control reduces downtime and improves cycle stability; the FP4 chipformer is engineered to break and evacuate chips efficiently during finishing and light to medium turning. This reduces the risk of built-up edge and surface damage while supporting higher feed rates where applicable. The insert’s 0.4 mm corner radius protects the cutting edge against premature chipping and helps maintain dimensional accuracy over longer tool sequences, promoting consistent production flow and fewer interruptions for insert changes. Versatility, handling and economic benefits With a T3 plate thickness and compact 11 size, the indexable plate suits a broad range of toolholders and lean machining setups. The coated carbide WPP10G grade balances wear resistance and toughness, making it an economical choice for many Stahl machining tasks: longer intervals between indexings, fewer insert changes and improved overall productivity. For workshops seeking a dependable finishing insert that is easy to specify and integrates into existing turning cells, this insert reduces the total cost per part through durability and steady performance. Contact Metav Werkzeuge for tailored cutting parameters and to source the Walter Tools DCMT11T304-FP4 WPP10G insert — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for direct advice and availability Technical data Article number: DCMT11T304-FP4-WPP10G-WALTER Designation: DCMT11T304-FP4 WPP10G Manufacturer: Walter Tools Series: Tiger·tec Gold Facts Shape: Rhombus 55° Size: 11 Thickness: T3 Corner radius: 0.4 mm Clearance angle: 7° Tolerance class: M Special features Grade: WPP10G (coated carbide, Tiger·tec Gold) Chipbreaker: FP4 Product type: Indexable turning insert Application group: P (Stahl) Execution: T FAQ What workpiece materials is this insert intended for? The DCMT11T304-FP4 WPP10G insert is specified for the ISO group P and is designed primarily for machining Stahl. What are the main benefits of the Tiger·tec Gold grade? The Tiger·tec Gold coating on the WPP10G grade offers a combination of wear resistance and toughness that extends tool life and supports stable processing in Stahl turning applications. How does the FP4 chipbreaker affect machining? The FP4 chipbreaker provides controlled chip formation and evacuation during finishing and medium turning, reducing the likelihood of built-up edge and improving surface quality. Is the 0.4 mm corner radius suitable for finishing? The 0.4 mm corner radius is a compromise between edge strength and fine surface finish; it protects the cutting edge while still enabling precise finishing cuts. Which geometry does the insert use and why does it matter? The rhombic 55° geometry offers versatile approach angles for a range of turning tasks, helping to reduce cutting forces and support consistent dimensional results. Manufacturer: Walter Tools — The Walter AG (brand presentation: Walter Tools) with headquarters in Tübingen is one of the world's leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective holders. Brand names and protected trade names are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered item is original, brand-new merchandise from the manufacturer.
DCMT11T304-FP4 WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance from the Tiger‑tec Gold grade, a proven FP4 chipbreaker for consistent chip control, and a compact rhombic 55° geometry for versatile turning of steel; order directly via Metav Werkzeuge or consult our team for application support. DCMT11T304-FP4 WPP20G — indexable turning insert for steel, Tiger‑tec Gold (Walter Tools) The DCMT11T304-FP4 WPP20G is a rhombic 55° indexable turning insert engineered for general steel turning applications where consistent tool life and controlled chip formation are essential. Rhombic 55° geometry for versatile turning Tiger‑tec Gold coated carbide for wear resistance FP4 chipbreaker for reliable chip control 0.4 mm corner radius for finishing and semi‑roughing Optimised carbide grade for cost‑efficient steel machining The coated carbide grade WPP20G (Tiger‑tec Gold) combines wear resistance and toughness to maintain a consistent cutting edge in a wide range of steel applications. Designed for ISO group P (steel), this grade balances tool life and process stability, reducing downtime due to frequent insert changes. The result is a measurable improvement in machining economy: fewer interruptions, steadier surface quality and predictable reconditioning intervals. The coated carbide technology mitigates adhesion and thermal wear, which translates into longer productive cycles on medium to high cutting speeds. Geometry and chip control that improve surface quality A rhombic 55° shape with a clearance angle of 7° and the FP4 chipbreaker delivers smooth chip formation and evacuation, especially in continuous and interrupted cuts. The small corner radius of 0.4 mm supports fine surface finishes while still allowing modest material removal rates. These geometric features mean fewer rework passes and less need for downstream finishing. Because the insert is indexable, the stable cutting edge and predictable wear behaviour help maintain dimensional accuracy over multiple edge changes, supporting tighter process control on batch runs. Practical selection and machining guidance for reliable results When selecting insert geometry and grade, match cutting speed and feed to the grade characteristics and workpiece alloy. The WPP20G grade is optimised for unalloyed and alloyed steels and copes well with the heat and chip formation typical of steel turning. For moderate feeds and finish turning, the 0.4 mm radius performs best; for heavier cuts, consider a larger radius where available. The insert’s T3 thickness and tolerance class M ensure stable clamping in compatible toolholders, minimising vibration and edge chipping. For complex applications or mixed material batches, contact our technical advisers for parameter charts and proven starting values. For tailored advice on using Walter Tools Tiger‑tec Gold inserts in steel turning and to place orders via Metav Werkzeuge, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 — technical consultation available Technical data Article number: DCMT11T304-FP4-WPP20G-WALTER Label: Drehwendeschneidplatte DCMT11T304-FP4 WPP20G Walter Tools ISO designation: DCMT11T304-FP4 WPP20G Manufacturer: Walter Tools Series: Tiger‑tec Gold Facts Clearance angle: 7° Corner radius: 0.4 mm Plate size: 11 mm Plate thickness: T3 Tolerance class: M Special features Coating/grade: Tiger‑tec Gold (WPP20G) Chipbreaker: FP4 Plate form: Rhombus 55° Material application: Steel (ISO P) Execution: T FAQ What materials is this insert suitable for? The DCMT11T304-FP4 WPP20G insert is specified for ISO group P workpieces and is suitable for machining a broad range of steels, including unalloyed and alloyed steels. How does the FP4 chipbreaker affect performance? The FP4 chipbreaker promotes consistent chip formation and evacuation, reducing the risk of built‑up edge and improving surface finish during both continuous and interrupted turning. Is the Tiger‑tec Gold grade durable for production runs? Yes, the WPP20G Tiger‑tec Gold coating offers a balanced combination of wear resistance and toughness, providing long tool life and stable performance on steel machining tasks. What cutting geometry benefits does the rhombic 55° provide? The rhombic 55° form enables versatile turning operations with good access to external and certain internal profiles, while the 0.4 mm corner radius supports fine finishing without excessive tool stress. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer. Walter Tools is a referenced brand in the product description.
DCMT11T304-FP6 WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold wear resistance and the FP6 chipbreaker for consistent chip control and longer tool life; the rhombic 55° geometry and 0.4 mm corner radius support reliable surface finish in steel turning. Order the DCMT11T304-FP6 WPP10G directly via Metav Werkzeuge or consult our specialists for grade selection and availability. DCMT11T304-FP6 WPP10G – Walter Tools indexable turning insert, Tiger·tec Gold coating, FP6 chipbreaker A DCMT11T304-FP6 WPP10G indexable insert optimised for stable, productive turning of steel under ISO P conditions, featuring a rhombic 55° form and a modest free angle for robust performance Tiger·tec Gold coating for extended tool life FP6 chipbreaker for controlled chip formation Rhombic 55° form for versatile turning tasks 0.4 mm corner radius for consistent surface finish Consistent productivity from advanced coating and grade The combination of the Tiger·tec Gold coating and the WPP10G grade delivers high wear resistance and a balanced toughness suited to the thermal and mechanical demands of steel machining. As a coated carbide solution, this insert supports uninterrupted production by resisting flank wear and preserving the cutting edge under moderate to demanding cutting conditions. The FP6 chipbreaker is specifically designed to produce predictable, short chips in a wide range of steel alloys, reducing machine stoppages and improving cycle time. These technical choices translate into measurable efficiency gains and fewer tool changes during extended turning runs. Precise geometry for reliable surface quality The rhombic 55° insert geometry combined with a 0.4 mm corner radius and a 7° free angle provides a reliable balance between strength and finish capability. The relatively small corner radius helps to achieve consistent surface roughness on typical ISO P materials while maintaining an edge that tolerates intermittent cutting and light interruptions. The nominal plate size (11) and thickness T3 ensure mechanical stability in most standard DCMT tool holders, supporting repeatable results and reduced vibration. For operators seeking predictable part quality, these geometry features reduce variability between batches. Practical benefits for workshop integration and cost efficiency Designed for conventional turning tool systems, the insert's standard designation aligns with common toolholder families, enabling quick replacement and minimal setup time. The combination of a robust coated grade and the FP6 chip control reduces auxiliary costs associated with rework and scrap, increasing overall process yield. For production environments where steel is the primary workpiece material, the insert offers a pragmatic mix of wear resistance and edge stability that supports longer tool life and more consistent component tolerances. Technical staff will appreciate the straightforward specification and the ease of matching the insert to established turning parameters. For tailored recommendations on using Walter Tools’ Tiger·tec Gold inserts, contact Metav Werkzeuge for expert guidance and reliable supply – Metav Werkzeuge can advise on grade selection, stock availability and process optimisation. Technical data SKU: DCMT11T304-FP6-WPP10G-WALTER Article: DCMT11T304-FP6 WPP10G Manufacturer: Walter Tools Facts Free angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 55° Plate size: 11 Plate thickness: T3 Tolerance class: M Designation: DCMT11T304-FP6 Special features Grade: WPP10G (Tiger·tec Gold coated carbide) Chipbreaker: FP6 Series: Tiger·tec Gold Application group: ISO P (steel) Execution: T Material group code: P FAQ What materials is this insert suitable for? The DCMT11T304-FP6 WPP10G is formulated for ISO P materials; the WPP10G grade and Tiger·tec Gold coating are optimised for machining steel. How does the FP6 chipbreaker affect cutting performance? The FP6 chipbreaker is designed to produce controlled, short chips in steel turning, improving chip evacuation and reducing the risk of entanglement. What key geometry features support surface finish? The rhombic 55° form combined with a 0.4 mm corner radius and a 7° free angle contributes to consistent surface finish and stable cutting behaviour. Is this insert compatible with standard DCMT tool holders? Yes, the insert follows the DCMT designation and is compatible with corresponding indexable turning holders that accept this geometry and size. Which manufacturer produces this grade and insert? Walter Tools supplies the DCMT11T304-FP6 WPP10G as part of the Tiger·tec Gold range, offering a coated carbide solution tailored to steel turning. Hersteller: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Die Walter AG (Markenauftritt: Walter Tools) gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT11T304-FP6 WPP20G Wendeplatten - Walter Tools
Benefit from the combination of long-lasting Tiger‑tec Gold coating and precise FP6 chip control to keep turning processes productive and consistent; order through Metav Werkzeuge or consult their specialists for application advice. DCMT11T304-FP6 WPP20G Indexable Turning Insert for Steel – Walter Tools (Tiger‑tec Gold, FP6) The DCMT11T304-FP6 WPP20G is an indexable turning insert engineered for reliable steel machining, combining Tiger‑tec Gold coated carbide with an FP6 chipbreaker for stable cutting and extended tool life. Tiger‑tec Gold coated carbide for long tool life FP6 chipbreaker for stable chip control 7° clearance angle for reliable cutting geometry Rhombic 55° form with 0.4 mm nose radius High endurance cutting performance for steel turning The Tiger‑tec Gold WPP20G grade delivers a balanced combination of wear resistance and toughness optimised for steels in the ISO P group. The coated carbide substrate offers improved heat resistance and edge stability, which translates into longer tool life and fewer index changes in medium- to high-volume turning operations. As a result, process efficiency increases and downtime for insert changes is reduced. The grade’s design supports steady chip formation, helping to avoid unpredictable breakouts and protecting the workpiece surface finish. Geometry and chip control designed to improve productivity The insert’s FP6 chipbreaker and Rhombic 55° profile provide predictable chip evacuation and consistent cutting forces. The 7° clearance angle maintains a controlled engagement with the workpiece while the 0.4 mm nose radius balances surface finish and corner strength for a wide range of turning passes. The nominal size of 11 mm and thickness T3 are suitable for standard toolholders that accept DCMT inserts. Clear explanation: the chipbreaker shapes the chips to prevent entanglement and to reduce thermal spikes at the cutting edge, so cycle times remain stable and tool life is more consistent across batches. Practical benefits in daily production and integration Using this indexable insert supports reproducible results and straightforward tool management. The combination of grade, coating and geometry makes it suitable for diverse steel applications—from general turning to semi-finishing—while keeping machine feeds and speeds efficient. For decision-making: where tighter tolerances or higher material hardness are not required, this insert offers an economical route to improved productivity and reduced scrap rates. If additional technical parameters or compatibility checks are needed, Metav Werkzeuge provides application support and can advise on cutting data and holder selection. Contact Metav Werkzeuge to discuss process optimisation with the DCMT11T304-FP6 WPP20G insert from Walter Tools and request tailored cutting data or a supply recommendation. Technical Data Article number: DCMT11T304-FP6-WPP20G-WALTER Name: Drehwendeschneidplatte DCMT11T304-FP6 WPP20G Walter Tools Manufacturer: Walter Tools Product type: Indexable turning insert Facts Size: 11 mm Clearance angle: 7° Corner radius: 0.4 mm Thickness: T3 Special features Coating: Tiger‑tec Gold Grade: WPP20G Chipbreaker: FP6 Form: Rhombic 55° Series: Tiger‑tec Gold Application: Steel (ISO P) Tolerance class: M Execution: T FAQ Is this insert suitable for stainless steel? The DCMT11T304-FP6 WPP20G insert is formulated for steel (ISO P); stainless steel suitability is not specified for this grade and should be verified with Metav Werkzeuge for specific stainless applications. What does the FP6 chipbreaker do? The FP6 chipbreaker shapes and controls chips during turning, promoting reliable chip evacuation and more consistent cutting forces, which helps to protect the cutting edge and improve surface finish when machining steels. What are the key geometric features of the insert? Key features include the Rhombic 55° form, 7° clearance angle and 0.4 mm nose radius; these combine to deliver controlled engagement and a balance between surface quality and edge strength. Can the insert be used for finishing and semi-finishing? Yes, the grade and geometry are suitable for semi-finishing and many finishing passes on steels, offering consistent results and good tool life in typical turning operations. Which toolholders accept this insert? The DCMT11T304-FP6 designation corresponds to standard holders for DCMT-style inserts; confirm holder compatibility and clamping style with Metav Werkzeuge when selecting tooling. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original, factory-new goods of the manufacturer Walter Tools.
DCMT11T304-FW4 WKP01G WKP01G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold performance, the WKP01G coated carbide grade and the FW4 chipbreaker for stable chip control and consistent turning results; order directly via Metav Werkzeuge or consult our specialists for cutting data and process optimisation. DCMT11T304-FW4 WKP01G indexable turning insert, Tiger‑tec Gold – for steel and cast iron | Walter Tools The DCMT11T304-FW4 WKP01G is an indexable turning insert engineered for general turning of steel and cast iron, offering a balanced mix of wear resistance and reliable chip formation in industrial production environments. Tiger‑tec Gold coated carbide grade WKP01G FW4 chipbreaker for predictable chip control Rhombic 55° geometry for versatile turning 7° clearance and 0.4 mm nose radius for precision High-performance grade for steady production results The insert’s Tiger‑tec Gold coating combined with the WKP01G grade delivers a high degree of wear resistance and consistent edge life when machining steels and cast irons. By using a coated carbide substrate optimised for typical heat and chip characteristics of these materials, the component reduces unscheduled tool changes and supports longer production runs. The coating’s thermal and tribological properties help maintain cutting edge integrity, which translates into predictable part quality and reduced scrap rates in serial machining. Geometry and chip control that increase process reliability With a Rhombic 55° shape and the FW4 chipbreaker, the geometry promotes controlled chip segmentation and smooth evacuation in a wide range of turning conditions. The 0.4 mm nose radius improves surface finish on external profiles, while the 7° clearance reduces rubbing at the flank, lowering cutting forces and heat generation. For applications where consistent chip form and surface quality matter, this geometry supports stable cutting behaviour and easier downstream handling of turned parts. Practical integration for workshop and production use The insert’s designation and thickness (T3) make it suitable for common toolholder systems; the indexable format allows quick indexing or replacement without regrinding, saving setup time. As a coated carbide insert designed for P and K groups, it adapts to both unalloyed/low‑alloy steels and abrasive cast iron grades, reducing the need for multiple tool types. For manufacturers aiming for efficient tool management and reproducible component accuracy, this insert combines robust performance with straightforward interchangeability. For tailored cutting parameters or to discuss toolholder compatibility for Walter Tools Tiger‑tec Gold inserts, contact Metav Werkzeuge for personalised advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: DCMT11T304-FW4-WKP01G-WALTER Designation: DCMT11T304-FW4 WKP01G Product type: indexable turning insert Manufacturer: Walter Tools Series: Tiger‑tec Gold Core data Free angle: 7° Nose radius: 0.4 mm Insert form: Rhombic 55° Insert size: 11 Thickness: T3 Tolerance class: M Special features Coating: Tiger‑tec Gold Grade: WKP01G (coated carbide) Chipbreaker: FW4 Material groups: steel (P), cast iron (K) Execution: T FAQ What materials is this insert suited for? The DCMT11T304-FW4 WKP01G is specified for machining steel (P) and cast iron (K); the WKP01G grade and Tiger‑tec Gold coating are optimised for these material groups. How does the FW4 chipbreaker affect machining? The FW4 chipbreaker on this insert promotes predictable chip segmentation and reliable evacuation, improving process stability during turning operations. What is the effect of the 0.4 mm nose radius? A 0.4 mm nose radius balances a good surface finish with the mechanical strength of the cutting edge, supporting accurate external profiles without excessive tool stress. Can the insert be indexed in standard holders? Yes, the insert follows common indexable turning geometries (Rhombic 55° and T3 thickness), enabling straightforward use in compatible toolholders. Does the WKP01G grade require special cutting speeds? Cutting data depend on the workpiece grade and machining strategy; WKP01G is a versatile coated carbide grade—consult process charts or Metav Werkzeuge for optimised parameters. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered article is an original, factory‑new product of the manufacturer.
DCMT11T304-FW4 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the wear-resistant WPP10G grade for high productivity in steel turning; the optimised FW4 chipbreaker and rhombic geometry ensure reliable chip control and consistent surface quality. Order directly via Metav Werkzeuge or contact the sales team for cutting data and application advice. DCMT11T304-FW4 WPP10G Turning insert (Tiger·tec Gold) for steel – Walter Tools The DCMT11T304-FW4 WPP10G is a rhombic 55° indexable turning insert engineered for efficient steel machining with a 7° relief angle and a 0.4 mm corner radius. Tiger·tec Gold coated carbide grade WPP10G Optimised FW4 chipbreaker for reliable chip control Rhombic 55° geometry with 0.4 mm corner radius 7° relief angle for stable cutting performance High-performance cutting tailored for steel production The combination of Tiger·tec Gold coating and the WPP10G grade yields a balance of wear resistance and fracture toughness that supports sustained productivity when machining steel. The coated carbide substrate reduces flank wear and maintains a stable cutting edge over extended runs, which translates into fewer tool changes and improved process economy. This makes the insert particularly suitable where repeatable performance and predictable tool life are required for batch or continuous production environments. Consistent chip control and improved surface finish The integrated FW4 chipbreaker is designed to form and evacuate chips reliably during common steel turning operations, reducing the risk of built-up edge and improving surface integrity. Combined with the rhombic 55° form and a 0.4 mm corner radius, the geometry supports controlled cutting engagement and a good balance between edge strength and finish. The 7° relief reduces rubbing at the flank, helping to keep cutting forces stable and contributing to more consistent part tolerances and improved component appearance. Robust specification for predictable process planning With a compact plate size and a T3 thickness, the insert adheres to a tolerance class M, providing predictable seating and repeatability across toolholders. The designation emphasises suitability for general steel applications (material group P) and supports a wide range of feed and speed settings when combined with appropriate machining parameters. As a Walter Tools product from the Tiger·tec Gold series, the insert integrates well into existing tooling systems and simplifies spare-part logistics for production shops seeking dependable, repeatable results. For application-specific recommendations and cutting data for the DCMT11T304-FW4 WPP10G insert from Walter Tools, contact Metav Werkzeuge for personalised advice and rapid order handling via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: DCMT11T304-FW4-WPP10G-WALTER Label: Drehwendeschneidplatte DCMT11T304-FW4 WPP10G Walter Tools Manufacturer: Walter Tools Product type: Turning insert ISO designation: DCMT11T304-FW4 WPP10G Numbers / Core technical data Plate size: 11 Thickness: T3 Corner radius: 0.4 mm Relief angle: 7° Plate form: Rhombic 55° Tolerance class: M Special features / Versions Grade: WPP10G (coated carbide) Coating technology: Tiger·tec Gold Chipbreaker: FW4 Material application: Steel (P) Series: Tiger·tec Gold FAQ What materials is this insert suited for? The DCMT11T304-FW4 WPP10G insert is specified for steel machining (ISO group P) and the WPP10G grade is optimised for the thermal and chip-formation characteristics typical of steel. How does the FW4 chipbreaker affect machining? The FW4 chipbreaker on the DCMT11T304-FW4 optimises chip formation and evacuation, reducing the likelihood of long, stringy chips and supporting consistent surface quality and process reliability. What is the benefit of the rhombic 55° geometry and 0.4 mm radius? The rhombic 55° form with a 0.4 mm corner radius balances edge strength and finishing capability, enabling stable cutting with good part tolerances and an improved surface finish in turning operations. Is this insert compatible with standard DCMT toolholders? The DCMT11T304-FW4 designation corresponds to standard DCMT insert geometry and is compatible with toolholders designed for DCMT 11-sized inserts when clamped and seated per the holder manufacturer’s instructions. What advantages does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating enhances wear resistance and edge stability under the thermal loads of steel turning, which supports longer tool life and consistent machining performance. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanation. There is no connection between our company and the named brands. The offered article is an original, brand-new product from Walter Tools.
DCMT11T304-FW4 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of a Tiger‑tec Gold coated grade, an optimised FW4 chipbreaker and a compact rhombic geometry for efficient steel turning; order genuine Walter Tools inserts via Metav Werkzeuge or consult the technical team for application advice. DCMT11T304-FW4 WPP20G turning insert — Tiger‑tec Gold grade for steel applications | Walter Tools The DCMT11T304-FW4 WPP20G is a rhombic 55° turning insert designed for stable chip control and reliable performance in steel machining, featuring a Tiger‑tec Gold coated carbide grade and a FW4 chipbreaker for consistent results. Tiger‑tec Gold coated carbide grade WPP20G Optimised FW4 chipbreaker for stable chips Rhombic 55° form with 0.4 mm corner radius 7° clearance angle for reliable cutting action High efficiency and predictable wear behaviour for steel machining The coated carbide WPP20G grade, developed within the Tiger‑tec Gold family, combines a wear-resistant top layer with a substrate engineered for strength. This composition reduces flank wear and extends edge life in common steel turning tasks, translating into fewer insert changes and higher machine uptime. The rhombic 55° geometry concentrates cutting forces to a defined edge, enabling a stable cutting process and improved tool life under varying feeds and depths. For shops targeting consistent cycle times, the material and design offer a measurable improvement in process reliability. Optimised chip control and cutting performance The FW4 chipbreaker has been designed to shepherd chips efficiently across a broad range of cutting conditions typical for steels (ISO group P). By controlling chip flow and fragmentation, the chipbreaker reduces the risk of re-cutting and tool damage while supporting steady surface finish quality. The combination of a 0.4 mm corner radius and 7° clearance angle balances strength and edge sharpness, making the insert suitable for finishing to medium turning operations where surface integrity and dimensional repeatability matter. Explanations of chipbreaker function: it shapes and breaks the chip to avoid long, stringy swarf and to keep thermal loads controlled. Practical benefits for production environments With a tolerance class of M and a compact T3 thickness, the insert fits common indexable tooling systems and offers a dependable performance envelope for general steel turning. The coated carbide construction provides high process security and predictable wear progression, which supports planning of tool change intervals and inventory. Where throughput and consistent part quality are priorities, the engineered grade and geometry reduce machine downtime and contribute to more efficient batch processing without the need for complex parameter tuning. Contact Metav Werkzeuge for application recommendations and to secure original Walter Tools DCMT11T304-FW4 WPP20G inserts — eMail: info@metav-werkzeuge.com · Tel: +49 2822 7131930 Technical data Article number: DCMT11T304-FW4-WPP20G-WALTER Label: Drehwendeschneidplatte DCMT11T304-FW4 WPP20G Walter Tools Manufacturer: Walter Tools Product type: Turning insert Series: Tiger‑tec Gold Grade: WPP20G Chipbreaker: FW4 Core specifications Clearance angle: 7° Corner radius: 0.4 mm Insert size: 11 mm Thickness: T3 Tolerance class: M Shape: Rhombic 55° Design and applications Coated carbide (Tiger‑tec Gold technology) Optimised for steel (ISO group P) Suitable for finishing to medium turning operations Stable chip control with FW4 breaker Execution: T FAQ What materials is this insert intended for? This turning insert is specified for steel machining (ISO group P); the WPP20G grade is optimised for unalloyed and alloyed steels. How does the FW4 chipbreaker affect performance? The FW4 chipbreaker on the DCMT11T304-FW4 WPP20G promotes controlled chip fragmentation, improving swarf handling and reducing the risk of re-cutting and edge damage. What edge preparation and geometry are provided? The insert features a rhombic 55° shape with a 0.4 mm corner radius and a 7° clearance angle, balancing edge strength and surface quality for finishing to medium operations. Can this insert be used for stainless steel or other alloys? The provided data specifies suitability for steels (ISO P). Use for stainless or specialised alloys is not listed in the available information and should be validated with process trials or technical consultation. Which toolholders accept this insert? The DCMT11T304-FW4 WPP20G conforms to standard indexable turning insert dimensions for its geometry; toolholder compatibility depends on the clamping seat matching the DCMT form and size. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners and are mentioned solely for clarification. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer.
DCMT11T304-FW4 WSM10S WSM10S Wendeplatten - Walter Tools
Benefit from a high-performance insert that combines the Tiger·tec Silver coating with the WSM10S grade and a precise 0.4 mm corner radius for dependable machining of stainless steels and heat‑resistant alloys; order directly via Metav Werkzeuge or ask our consultants for application support. DCMT11T304-FW4 WSM10S indexable turning insert — Tiger·tec Silver for stainless steels and superalloys (Walter Tools) The DCMT11T304-FW4 WSM10S is an indexable turning insert engineered for secure chip formation and a stable cutting edge when machining stainless steels and high‑temperature alloys in demanding production environments Tiger·tec Silver coated grade WSM10S Stable cutting edge for stainless steels FW4 chipbreaker for reliable chip control 7° clearance and 0.4 mm corner radius Reliable cutting performance on difficult materials The combination of the WSM10S coated carbide and the Tiger·tec Silver technology delivers improved heat resistance and wear behaviour, which translates into longer tool life and fewer interruptions in production. The grade is tailored for machining stainless steels (ISO group M) and heat‑resistant superalloys (ISO group S), materials that tend to work‑harden and generate high cutting temperatures. By choosing this insert, processes benefit from consistent cutting behaviour and reduced risk of built‑up edge, supporting predictable cycle times and less scrap. Geometry that improves surface quality and tool stability The rhombic 55° insert geometry, combined with a 0.4 mm corner radius and a 7° clearance angle, gives a balance between strength and accessibility for finishing and light roughing cuts. The modest corner radius helps to dampen vibrations while producing a uniform surface finish, and the clearance angle reduces rubbing on the flank face. These geometry choices provide a measurable improvement in repeatability and part finish compared with generic inserts, making the component better suited to precision turning of challenging alloys. Controlled chips and process reliability with FW4 chipbreaker The FW4 chipbreaker is designed to form short, manageable chips under a range of cutting conditions, reducing the risk of entanglement and improving coolant access to the cutting zone. Effective chip control lowers cycle variability and increases operator safety at the machine. For materials that are prone to long, stringy chips, the chipbreaker geometry and the stable cutting edge of this insert work together to maintain continuous machining and support unattended or lights‑out production runs. System compatibility and cost‑effective productivity This insert is supplied in the common DCMT format and the size 11 profile, allowing easy integration into many standard turning toolholders. The T3 thickness and the robust grade selection support a good compromise between edge strength and insert economy. The use of a coated carbide grade from a recognised manufacturer reduces tooling change frequency and can lower total cost per part through extended cutting intervals and consistent performance across batch production. Contact Metav Werkzeuge for a tailored recommendation and request the Walter Tools DCMT11T304-FW4 WSM10S insert for machining trials or technical advice Technical Data Article number: DCMT11T304-FW4-WSM10S-WALTER Product type: Indexable turning insert Manufacturer: Walter Tools Core data Insert designation: DCMT11T304-FW4 WSM10S Grade / coating: WSM10S / Tiger·tec Silver Insert size: 11 (inscribed circle) Thickness: T3 Corner radius: 0.4 mm Clearance angle: 7° Chipbreaker: FW4 Tolerance class: M Special features Rhombic 55° insert shape Coated carbide for stainless steels and superalloys Stable cutting edge for demanding materials Designed for controlled chip formation and surface quality FAQ What materials is this insert suitable for? The DCMT11T304-FW4 WSM10S insert is specified for stainless steels (ISO group M) and heat‑resistant superalloys/titanium (ISO group S), making it suitable for demanding applications where heat and work hardening are factors. How does the Tiger·tec Silver coating benefit machining? The Tiger·tec Silver coating on the WSM10S grade increases thermal resistance and reduces wear, which improves tool life and maintains cutting performance when machining high‑temperature alloys. Can the insert be used for finishing as well as roughing? Yes; the rhombic 55° geometry with a 0.4 mm corner radius and 7° clearance offers a compromise suitable for light roughing and finishing, delivering stable cutting and consistent surface quality. Is the FW4 chipbreaker effective for automatic chip evacuation? The FW4 chipbreaker produces short, controllable chips across a range of cutting parameters, aiding automatic chip evacuation and supporting lights‑out machining where reliable chip control is essential. Which toolholders are compatible with this insert? The insert follows the DCMT indexable insert standard and fits common toolholders designed for that format; check holder compatibility with the insert designation DCMT11T304-FW4 WSM10S. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany, info@walter-tools.com Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT11T304-FW4 WSM20S FW4 Wendeplatten - Walter Tools
Take advantage of the combination of a wear-resistant WSM20S grade, proven Tiger·tec Silver coating and the FW4 chipbreaker for steady chip control and repeatable results; this combination supports efficient machining of stainless steel and heat-resistant superalloys. Order the original inserts or consult Metav Werkzeuge for process data and application advice. DCMT11T304-FW4 (ISO: DCMT11T304-FW4) WSM20S — Drehwendeschneidplatte for stainless steel and superalloys by Walter Tools The DCMT11T304-FW4 WSM20S is a rhombic 55° turning insert designed for reliable finishing and medium-heavy turning of stainless steel and heat-resistant superalloys, combining a coated carbide grade with an FW4 chipbreaker for controlled swarf formation Tiger·tec Silver coating for wear resistance FW4 chipbreaker for reliable chip control Rhombic 55° geometry for versatile turning Optimised for stainless steel and superalloys Durable coating and material science for longer tool life The combination of the WSM20S grade with the Tiger·tec Silver coating provides a balanced solution between wear resistance and edge toughness. As a coated carbide grade, it is engineered to withstand the thermal and adhesive stresses typical of stainless steel and nickel‑based alloys; the coating reduces flank wear and helps to delay edge breakdown. For production environments this means fewer insert changes and more predictable tool life, which directly contributes to higher machine uptime and lower unit costs. Geometry and chip control that stabilise the process The FW4 chipbreaker and the Rhombic 55° plate geometry work together to ensure consistent chip formation and evacuation. The chipbreaker is tailored to aid fragmenting or curling of swarf depending on cutting parameters, reducing the risk of entanglement and promoting stable cutting forces. The combination of a 7° relief angle and a 0.4 mm corner radius provides a compromise between edge strength and surface finish, supporting reliable machining under varying feed rates and depths of cut. Designed for demanding materials and repeatable results This insert is specifically specified for the ISO material groups M and S, making it suitable for stainless steel as well as heat‑resistant superalloys and titanium — materials that characteristically generate high temperatures and adhere to cutting edges. The grade and geometry promote safe chip control and a stable cutting edge, which helps to avoid built‑up edge formation and to maintain dimensional accuracy over series production. The overall design therefore supports process security and consistent part quality. Practical handling and selection for workshop productivity The DCMT format and the clear designation simplify inventory and toolholder selection in a production setting. The T3 plate thickness and the rhombic shape allow compatibility with a wide range of toolholders while the tolerance class M ensures interchangeability and repeatable seating. Selecting this insert family reduces the number of tool variants required for stainless steel and superalloy tasks, supporting streamlined tool management and faster changeovers on the shop floor. Contact Metav Werkzeuge for material‑specific cutting data and secure genuine Walter Tools DCMT11T304-FW4 WSM20S inserts for reliable stainless steel and superalloy machining Technical data Article number: DCMT11T304-FW4-WSM20S-WALTER Type: Drehwendeschneidplatte / indexable turning insert Designation: DCMT11T304-FW4 ISO designation: DCMT11T304-FW4 WSM20S Grade/sort: WSM20S Series: Tiger·tec Silver Manufacturer: Walter Tools Facts Free angle: 7° Corner radius: 0.4 mm Insert size: 11 mm Plate thickness: T3 Plate form: Rhombic 55° Tolerance class: M Special features Coating: Tiger·tec Silver Chipbreaker: FW4 Material suitability: stainless steel (M), superalloys and titanium (S) Coated carbide grade for demanding materials Intended for medium‑to‑heavy turning and finishing operations FAQ What materials is this insert suitable for? The DCMT11T304-FW4 WSM20S insert by Walter Tools is specified for stainless steel (ISO group M) and heat‑resistant superalloys and titanium (ISO group S), offering thermal resilience and edge stability for those materials. Which chipbreaker is fitted and what benefit does it provide? The insert features the FW4 chipbreaker, which promotes controlled chip formation and reliable evacuation, reducing the risk of swarf-related interruptions during turning. How does the corner radius affect performance? A corner radius of 0.4 mm balances edge strength and surface finish; this radius supports durable edges under moderate depths of cut while helping to maintain dimensional accuracy. Is this insert compatible with standard DCMT toolholders? The DCMT format and T3 thickness align with industry DCMT toolholders; compatibility depends on the specific holder geometry and clamping method used. What performance advantages does the Tiger·tec Silver series offer? The Tiger·tec Silver coating on the WSM20S grade enhances wear resistance and thermal protection, leading to longer, more predictable insert life in demanding stainless steel and superalloy machining tasks. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT11T304-FW4 WSM30S FW4 Wendeplatten - Walter Tools
Take advantage of the combination of high process reliability, durable Tiger·tec Silver coating and precise FW4 chip control for steady production in stainless steel and superalloy turning; order the insert directly via Metav Werkzeuge or consult our specialists if clarification is required. DCMT11T304-FW4 WSM30S – Turning insert DCMT11T304-FW4, grade WSM30S for stainless steel by Walter Tools The DCMT11T304-FW4 WSM30S is a rhombic 55° turning insert designed for demanding stainless steel and heat‑resistant superalloy machining, combining Tiger·tec Silver coating with an FW4 chipbreaker for reliable chip control. Tiger·tec Silver coating for heat resistance Designed for stainless steel and superalloys FW4 chipbreaker for consistent chip control Rhombic 55° shape with 0.4 mm corner radius Stable machining under high thermal load The insert’s core advantage is its Tiger·tec Silver technology paired with a WSM30S coating grade: a coated carbide formulation engineered to withstand the thermal and mechanical stresses typical of stainless steel and nickel‑based alloys. This results in increased tool life and fewer interruptions for tool changes, which in turn lowers process costs and supports longer unmanned runs. The combination of heat resistance and edge stability reduces the risk of build‑up formation and preserves component surface quality under elevated cutting temperatures. Reliable chip control for predictable cycle times A precisely defined FW4 chipbreaker and the rhombic 55° geometry create controlled chip segmentation across a range of feeds and depths. The moderate corner radius of 0.4 mm helps to balance cutting forces and edge strength, making the insert suitable for both roughing and semi‑finishing passes where stable chips are essential for machine safety and part consistency. Clear chip behaviour shortens cycle time variability and simplifies coolant and chip management at the machine. Geometry and tolerances that support repeatable parts Built to tolerance class M and provided in the execution T with plate thickness T3, this insert offers repeatable seating and predictable cutting geometry when used in appropriately matched toolholders. The 7° clearance angle (7°) and the rhombic platform ensure secure seating and stable engagement in tight radii or interrupted cuts. For production environments requiring consistent surface finishes and dimensional control, the geometry reduces vibration and helps maintain process stability from the first to the last component. Choose the Walter Tools Tiger‑tec Silver WSM30S insert for demanding stainless steel and superalloy turning—request technical advice or place an order with Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: DCMT11T304-FW4-WSM30S-WALTER Label: Drehwendeschneidplatte DCMT11T304-FW4 WSM30S Walter Tools Manufacturer: Walter Tools Series: Tiger-tec Silver Grade: WSM30S Core specifications Corner radius: 0.4 mm Clearance angle: 7° Plate size: 11 mm Plate thickness: T3 Tolerance class: M Special features Chipbreaker: FW4 Plate form: Rhombus 55° Coating: Tiger·tec Silver (coated carbide) Material application: stainless steel (M), heat‑resistant superalloys and titanium (S) FAQ Which materials is this insert intended for? The DCMT11T304-FW4 WSM30S insert is specified for machining stainless steel and for heat‑resistant superalloys and titanium, matching the ISO groups M and S as noted in the technical description. What does the WSM30S grade and Tiger·tec Silver imply? WSM30S denotes a Walter Tools coated carbide grade in the Tiger·tec Silver family; the combination provides improved heat resistance and edge stability for high thermal loads during continuous cutting. How does the FW4 chipbreaker influence production? The FW4 chipbreaker ensures consistent chip segmentation and evacuation, reducing the risk of long, entangling chips and contributing to steady cycle times and safer machine operation with the DCMT11T304-FW4 geometry. Is the corner radius suitable for finishing? The 0.4 mm corner radius offers a compromise between edge strength and fine surface finish; for delicate finishing passes, adjustments to feed and depth will optimise surface quality while preserving tool life. Are there special considerations for toolholder selection? Choose a toolholder compatible with a rhombic 55° insert and ensure correct clamping to maintain the insert’s specified clearance angle and tolerance class; this supports the repeatability and process reliability expected from the WSM30S grade. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected product designations are mentioned solely for explanatory purposes. There is no connection between our company and the named brands; the offered item is an original, factory‑new product of Walter Tools.
DCMT11T304-MK4 WKK10S Wendeplatten - Walter Tools
Take advantage of the combination of high wear resistance, stable chip control and precise geometry for reliable cast-iron turning operations; order the inserts directly via Metav Werkzeuge or request a process consultation from our specialists. DCMT11T304-MK4 WKK10S turning insert — Walter Tools, Tiger·tec Silver, for cast iron The DCMT11T304-MK4 WKK10S is a coated indexable turning insert designed for productive machining of cast iron components using a rhombic 55° geometry. Tiger·tec Silver coating for long tool life Optimised for cast iron machining Rhombic 55° geometry with 0.4 mm radius MK4 chipbreaker for controlled chip flow Increased productivity through a wear-resistant grade The combination of the Tiger·tec Silver coating and the WKK10S grade delivers pronounced wear resistance when cutting cast iron, reducing flank wear and extending tool life. This grade is a coated carbide formulation optimised for abrasive cast materials, offering a favourable balance between durability and toughness. As a result, production runs achieve longer uninterrupted cycles and reduced tooling change frequency, which supports predictable throughput and lower process costs over time. Geometry and chip control for consistent surface quality The insert’s rhombic 55° shape and 0.4 mm corner radius produce a stable cutting edge that promotes dimensional consistency and a reliable surface finish. The MK4 chipbreaker is engineered to control short, breaking chips typical of cast-iron machining, improving evacuation and reducing the risk of built-up edge. The 7° clearance angle contributes to smooth engagement and helps prevent rubbing under varying feed and depth conditions, which leads to improved part quality and repeatability. Application advantages and process guidance for turning cast iron Engineered specifically for cast-iron applications, this indexable insert suits both serial production and jobbing workshops seeking process security. The coated grade and chipbreaker combination ensure predictable wear progression and stable cutting forces, simplifying parameter selection and reducing rework. For customers seeking tailored process settings or verification against existing toolholders, Metav Werkzeuge offers technical consultation to match the insert to holders and machine capabilities so that cycle times and surface results are optimised. For cast-iron turning tasks, contact Metav Werkzeuge to specify the DCMT11T304-MK4 WKK10S insert and obtain a customised process recommendation that maximises productivity while extending tool life. Technical Data Article number: DCMT11T304-MK4-WKK10S-WALTER Designation: DCMT11T304-MK4 WKK10S Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WKK10S Facts Geometry: Rhombic 55° Clearance angle: 7° Corner radius: 0.4 mm Size: 11 Thickness: T3 Tolerance class: M Special features MK4 chipbreaker Coated carbide grade (Tiger·tec Silver) Suitable for cast iron machining Balanced wear resistance and toughness FAQ What materials is this insert suitable for? The DCMT11T304-MK4 WKK10S insert is specified for cast iron applications; its coating and grade are tuned to resist abrasive wear typical of these materials. How does the MK4 chipbreaker affect machining? The MK4 chipbreaker on the DCMT11T304-MK4 WKK10S promotes short, controlled chips in cast-iron turning, improving chip evacuation and protecting the tool edge for more stable cuts. What benefits does the Tiger·tec Silver series provide? Tiger·tec Silver coating increases wear resistance and thermal stability, which in the DCMT11T304-MK4 WKK10S contributes to longer tool life and consistent performance in abrasive cast-iron operations. Which geometry advantages does the rhombic 55° offer? The rhombic 55° form with a 0.4 mm corner radius gives a compromise between strength and accessibility for internal and external turning, delivering stable cutting and reliable surface quality. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for product description and clarification. There is no affiliation between our company and the mentioned brands. The offered item is an original, factory-new product of the manufacturer.
DCMT11T304-MK4 WKK20S Wendeplatten - Walter Tools
High wear resistance, reliable chip control and a compact rhombic geometry ensure consistent productivity and predictable tool life; order the insert directly via Metav Werkzeuge or consult our specialists for machining support. DCMT11T304-MK4 WKK20S turning insert — Tiger‑tec Silver, for cast iron | Walter Tools The DCMT11T304-MK4 WKK20S is a rhombic 55° turning insert designed for productive and reliable machining of cast iron components. Tiger‑tec Silver coated grade WKK20S Optimised for cast iron machining MK4 chipbreaker for controlled chips 0.4 mm corner radius for stable edges Increased productivity for abrasive cast iron The coated carbide grade WKK20S from the Tiger‑tec Silver family is formulated to resist abrasive wear typical of cast iron. The combination of a robust coating and a geometry tailored to cast materials delivers consistent tool life and fewer unplanned tool changes, which improves machine utilisation. The rhombic 55° insert shape and the MK4 chipbreaker cooperate to produce short, predictable chips, reducing stoppages for chip clearing and supporting higher uninterrupted cutting periods. Stable cutting performance and surface quality A 0.4 mm corner radius provides a compromise between edge strength and surface finish: it stabilises the cutting edge under intermittent engagement while helping to maintain a steady component surface. The 7° clearance angle reduces flank rubbing, lowering heat build‑up and helping to preserve the edge for longer. These geometrical choices yield reliable dimensional results and repeatable surface quality in serial production without sacrificing tool life. Practical handling and process guidance The insert’s T3 thickness and size 11 format suit standard toolholders and allow straightforward tool set‑up in turning centres. The MK4 chipbreaker is designed to control the typically brittle, breaking chips of cast iron, simplifying evacuation and minimising manual intervention. If process parameters need adaptation for a specific grade of cast iron, Metav Werkzeuge’s technical advisors can provide cutting‑edge recommendations and setup tips to integrate the insert effectively into existing turning cycles. For secure and efficient cast iron turning with Walter Tools’ Tiger‑tec Silver grade, contact Metav Werkzeuge for delivery details and application advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: DCMT11T304-MK4-WKK20S-WALTER Designation: DCMT11T304-MK4 WKK20S Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.4 mm Insert shape: Rhombus 55° Insert size: 11 Thickness: T3 Tolerance class: M Special features Grade: WKK20S (Tiger‑tec Silver) Chipbreaker: MK4 Coated carbide for cast iron Series: Tiger‑tec Silver FAQ What materials is this insert intended for? The DCMT11T304-MK4 WKK20S turning insert is intended and optimised for machining cast iron materials. How does the chipbreaker improve production? The MK4 chipbreaker on the insert shapes and controls the typically short, brittle chips produced when machining cast iron, improving evacuation and reducing interruption in the machining process. Which geometry features support surface quality? The rhombic 55° shape together with a 0.4 mm corner radius and a 7° clearance angle help to balance edge strength and finish quality during turning operations. Is the grade suitable for continuous production runs? Yes, the WKK20S grade in the Tiger‑tec Silver series is formulated for wear resistance and stable cutting behaviour, supporting predictable performance in serial production. Can the insert be used with standard toolholders? The insert’s T3 thickness and size 11 format are compatible with common turning toolholders; verify holder seat compatibility before assembly. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand presentation: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and forms part of the Swedish Sandvik Group. Protected trademarks and trade names remain the property of their respective owners and are used here for explanation only. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of the manufacturer.
DCMT11T304-MM4 WMP20G WMP20G Wendeplatten - Walter Tools
Take advantage of a proven combination of durable coating and reliable geometry to maintain steady production when machining stainless steel; the Tiger·tec Gold grade WMP20G offers stable chip formation and extended edge life for medium to robust conditions. Contact Metav Werkzeuge for advice or to arrange supply. DCMT11T304-MM4 WMP20G indexable turning insert — Rhombus 55°, 7° clearance · Walter Tools The DCMT11T304-MM4 WMP20G is an indexable turning insert optimised for stainless steel machining in medium to robust operating conditions. DCMT11T304-MM4 WMP20G by Walter Tools Tiger·tec Gold coating for stable cutting edge Rhombus 55° form with 0.4 mm corner radius Optimised for stainless steel machining Stable cutting performance for demanding stainless steel work The Tiger·tec Gold WMP20G grade combines a coated carbide composition with a chipbreaker engineered for challenging materials, delivering edge stability where thermal load and material toughness are high. In practical terms, this means fewer interruptions from built-up edge and a steadier machining process when turning stainless steel. The result is more consistent dimensional accuracy and reduced risk of unexpected rework, which supports uninterrupted production schedules in contract machining and in-house turning operations. Geometry that ensures consistent surface quality and predictable feeds The Rhombus 55° insert form with a 0.4 mm corner radius and a 7° clearance angle provides a reliable cutting geometry that balances strength and accessibility. The modest corner radius contributes to robust edge life while permitting acceptable surface finish in finishing and light semi-finishing passes. With a T3 plate thickness and the specified clearance, the insert supports repeatable tool settings and predictable process parameters, facilitating faster set-up and more uniform part quality across batch runs. Cost-effective tool life and controlled chip behaviour Equipped with the MM4 chipbreaker, this insert is designed to promote controlled chip formation under the heat-prone conditions typical of stainless steel. The combination of grade and chip control reduces the frequency of insert changes and minimises machine downtime, yielding a favourable tool-life-to-cost ratio. For shops focused on throughput and process reliability, these characteristics translate into measurable operational benefits without sacrificing the precision required by tight tolerances. Application advice and process fit This insert is suitable for turning operations on stainless steel in medium to robust cutting regimes. The Tiger·tec Gold technology supports sustained productivity where surface integrity and edge stability are priorities. For optimal results, match the insert geometry and chipbreaker to the intended feed and depth of cut; the rhombic form offers flexibility for a range of turning tasks, from profiling to general external turning. For further machining parameters or grade comparisons, consult technical advisors to adapt speeds and feeds to specific machines and workpiece conditions. For tailored selection and availability of Walter Tools Tiger·tec Gold inserts for stainless steel applications, contact Metav Werkzeuge for expert guidance and quick supply via info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data Article number: DCMT11T304-MM4-WMP20G-WALTER Label: Drehwendeschneidplatte DCMT11T304-MM4 WMP20G Walter Tools Type: Indexable turning insert Series: Tiger·tec Gold Grade: WMP20G Chipbreaker: MM4 Core specifications Clearance angle: 7° Corner radius: 0.4 mm Plate size: 11 mm Thickness: T3 Shape: Rhombus 55° Materials & features Coating technology: Tiger·tec Gold Suitable for: stainless steel Edge design: optimised for stable cutting Manufacturer: Walter Tools FAQ What materials is this insert intended for? The DCMT11T304-MM4 WMP20G insert is designed primarily for machining stainless steel and performs well under medium to robust cutting conditions. Which chipbreaker is fitted and what does it support? The MM4 chipbreaker is specified for this grade; it supports controlled chip formation in heat-generating materials such as stainless steel. What are the key geometry values to consider for set-up? Important geometry values are the Rhombus 55° form, a 0.4 mm corner radius and a 7° clearance angle, which together influence surface finish and edge strength. Is this a coated or uncoated grade and what benefit does that provide? This is a coated carbide grade within the Tiger·tec Gold family; the coating enhances edge stability and contributes to extended tool life during stainless steel turning. Can the DCMT11T304-MM4-WMP20G-WALTER be used for finishing operations? Yes, the combination of geometry and grade allows for finishing and light semi-finishing passes, offering consistent surface quality when set up appropriately. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Walter AG (marketed as Walter Tools) is one of the leading manufacturers of precision tools for metalworking. Protected trademarks and brand names remain the property of their respective owners. Mention of brand names serves explanatory purposes only; there is no affiliation implied. The offered article is original, factory-new goods of the manufacturer.
DCMT11T304-MM4 WMP20S WMP20S Wendeplatten - Walter Tools
The combination of Tiger·tec Silver coating, an MM4 chipbreaker and a Rhombic 55° geometry delivers reliable chip control and extended tool life for stainless steel turning; efficient production and consistent surface quality result. Order the DCMT11T304-MM4 WMP20S directly via Metav Werkzeuge or consult the specialists if further application data is required. DCMT11T304-MM4 WMP20S — indexable turning insert for stainless steel by Walter Tools The DCMT11T304-MM4 WMP20S is an indexable turning insert engineered for machining stainless steel under medium to robust cutting conditions, offering controlled chip formation and stable edge performance. Tiger·tec Silver coating for robust performance Optimised MM4 chipbreaker for stable chip control Rhombic 55° form with 0.4 mm corner radius Designed for stainless steel machining Consistent cutting in challenging stainless steel applications The combination of the Tiger·tec Silver coating and the WMP20S grade is tailored to the demands of stainless steel turning. The coating reduces friction and improves thermal stability, which helps to avoid built-up edge and premature flank wear during difficult cuts. As a result, process reliability is increased and the number of interrupted production cycles is reduced. For production planners this translates into a more predictable tool life and fewer changeovers, supporting leaner machining routines. Geometry that supports surface quality and repeatability The Rhombic 55° shape with a 0.4 mm corner radius and 7° relief angle provides a balance between strength and edge sharpness. The modest corner radius helps produce a consistent surface finish while maintaining edge robustness in interrupted cuts or harder zones of workpieces. The MM4 chipbreaker is optimised to generate short, controllable chips on stainless steels, minimising chip entanglement and contributing to safer, cleaner machining operations. These geometry choices reduce the need for secondary finishing and support reproducible part tolerances. Productivity benefits and economical tool management As an indexable insert, the insert offers quick indexation and predictable reuse of cutting edges, lowering tooling costs per part compared with brazed tools. The T3 thickness and stable tolerance class ensure secure clamping and minimal vibration, which in turn reduces tool wear and improves component consistency. The grade’s suitability for corrosion-resistant alloys means fewer tool variants are required on the shop floor when processing diverse stainless steel grades, simplifying inventory and improving setup efficiency. For high-demand stainless steel turning, contact Metav Werkzeuge to order the Walter Tools DCMT11T304-MM4 WMP20S or to request tailored application advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: DCMT11T304-MM4-WMP20S-WALTER Designation: Indexable turning insert DCMT11T304-MM4 WMP20S Walter Tools Series: Tiger·tec Silver Facts Insert size: 11 Relief angle: 7° Corner radius: 0.4 mm Thickness: T3 Shape: Rhombic 55° Tolerance class: M Special features Grade: WMP20S (coated carbide) Chipbreaker: MM4 Suitable for: stainless steel Coating technology: Tiger·tec Silver Manufacturer: Walter Tools FAQ What materials is this insert suitable for? The DCMT11T304-MM4 WMP20S indexable turning insert from Walter Tools is specified for stainless steel applications and performs well in medium to robust cutting conditions. How does the MM4 chipbreaker affect machining? The MM4 chipbreaker is designed to produce short, controllable chips on stainless steels, improving chip flow and reducing the risk of entanglement during turning operations with this Walter Tools insert. Is the grade suitable for interrupted cuts? Yes; the combination of the Rhombic 55° geometry and a 0.4 mm corner radius provides edge strength that helps handle intermittent engagement while maintaining surface quality with the DCMT11T304-MM4 WMP20S. Can the insert be indexed multiple times? The insert is an indexable turning insert designed for multiple indexing cycles; consistent tolerance (class M) and the T3 thickness support repeatable clamping and subsequent reuse of edges. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade names are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original, brand-new goods of the manufacturer. Walter AG (brand presentation: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group.
DCMT11T304-MM4 WMP30G WMP30G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold coating and the WMP30G grade for reliable machining of rostfreier Stahl; the rhombic geometry and MM4 chipbreaker support stable chip formation and consistent surface quality, helping to maintain productivity and reduce tool changes. Order or request application advice via Metav Werkzeuge if further consultation is required. DCMT11T304-MM4 WMP30G — Indexable turning insert for rostfreier Stahl (Tiger·tec Gold) by Walter Tools The DCMT11T304-MM4 WMP30G is an indexable turning insert developed for medium to robust machining tasks on rostfreier Stahl, combining a versatile rhombic geometry with a specialised chipbreaker for controlled cutting. Tiger·tec Gold coated grade WMP30G Designed for rostfreier Stahl (ISO M) Rhombic 55° geometry for versatile turning 0.4 mm corner radius with MM4 chipbreaker Consistent cutting performance with Tiger·tec Gold The coated carbide Tiger·tec Gold grade provides a balanced combination of wear resistance and edge stability, which is particularly beneficial when machining rostfreier Stahl. The specific grade formulation promotes secure chip formation under the heat-generating conditions typical for these alloys, reducing the tendency for built-up edge and preserving surface integrity. In practice this means longer tool life and fewer interruptions for insert changes, helping to keep cycle times predictable and production flow steady. Controlled chips and improved surface finish A purpose-designed MM4 chipbreaker together with the rhombic 55° geometry yields reliable chip control and predictable cutting forces. The 0.4 mm corner radius contributes to a strong cutting edge that resists chipping during interrupted cuts while still allowing good surface finish on turned parts. The modest 7° relief angle supports stable contact conditions at the cutting edge, reducing vibration and promoting repeatable results in serial production. Economical use and process reliability Tolerance class M and the proven coating technology result in a cost-effective solution for demanding rostfreier Stahl applications. The insert’s T3 thickness and the overall design balance rigidity with accessibility for a range of toolholders. This combination reduces the need for frequent regrinding or replacement, supporting higher throughput and predictable tool consumption—factors that directly lower manufacturing costs over time. Practical application advice for predictable results Use this indexable insert for medium to robust finishing and semi‑finishing operations on rostfreier Stahl where stable chip formation is required. The combination of the WMP30G grade and the MM4 chipbreaker is geared towards avoiding built-up edge and maintaining a consistent cut. For matching toolholder and clamping recommendations, consider tool rigidity and mounting overhang to preserve the performance advantages of the insert and to achieve consistent surface quality. Discuss Walter Tools Tiger·tec Gold inserts with Metav Werkzeuge to confirm suitability for a specific rostfreier Stahl application and to check current availability — eMail: info@metav-werkzeuge.com | Tel: +49 2822 7131930 Technical Data SKU: DCMT11T304-MM4-WMP30G-WALTER Label: Drehwendeschneidplatte DCMT11T304-MM4 WMP30G Walter Tools Product type: Turning insert Series: Tiger·tec Gold Grade: WMP30G Manufacturer: Walter Tools Facts Relief angle: 7° Corner radius: 0.4 mm Size: 11 mm Plate thickness: T3 Geometry: Rhombic 55° Special features Coating/technology: Tiger·tec Gold Grade material: Coated carbide Chipbreaker: MM4 Tolerance class: M Suitable for rostfreier Stahl FAQ What materials is this insert suitable for? The DCMT11T304-MM4 WMP30G insert by Walter Tools is designed primarily for rostfreier Stahl (ISO M), offering secure chip formation under the higher heat and toughness conditions of these alloys. How does the MM4 chipbreaker affect machining? The MM4 chipbreaker on this turning insert stabilises chip flow and reduces the risk of built-up edge, improving surface finish and making the cutting process more predictable for rostfreier Stahl. Can this insert be used for finishing and semi‑finishing? Yes, the combination of the WMP30G grade and a 0.4 mm corner radius suits both semi‑finishing and finishing operations where a balance of tool life and surface quality is required. Is this insert compatible with standard toolholders? The DCMT11T304-MM4 WMP30G follows common indexable insert geometry (rhombic 55°), making it compatible with appropriate holders designed for this ISO form and size Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanatory purposes. There is no connection between our company and the mentioned brands. The offered article is an original, brand‑new product of the manufacturer.
DCMT11T304-MM4 WSM01 WSM01 Wendeplatten - Walter Tools
Benefit from a reliable balance of Tiger‑tec Silver coating, the WSM01 grade and the MM4 chipbreaker for secure chip control and consistent edge life; order directly via Metav Werkzeuge or consult our specialists for application advice. DCMT11T304-MM4 WSM01 turning insert — Tiger‑tec Silver, MM4 chipbreaker — Walter Tools A DCMT11T304-MM4 WSM01 indexable turning insert engineered for demanding turning of stainless steels and heat‑resistant superalloys, offering robust edge stability and controlled chip formation. Tiger‑tec Silver coating for high process security WSM01 grade optimised for stainless and superalloys MM4 chipbreaker for stable chip control 7° clearance with 0.4 mm corner radius Increased process security for difficult-to-machine materials The coated carbide combination of the Tiger‑tec Silver series and the WSM01 grade delivers enhanced heat resistance and wear control, which is vital when machining stainless steels and heat‑resistant superalloys. This indexable insert is a coated carbide solution designed to maintain a stable cutting edge under elevated temperatures and adhesive tendencies typical for these material groups. The result is predictable tool life and fewer interruptions in production, which supports continuous, economic machining cycles. Geometry that improves stability and component quality The rhombus 55° form and the specified 7° clearance angle reduce flank contact and improve approach geometry for a wide range of turning operations. The 0.4 mm corner radius increases edge robustness where light corner strength is required, while the T3 plate thickness contributes to radial and axial stiffness during cutting. Together, these design elements minimise vibration, promote consistent surface finish and reduce the risk of edge chipping when finishing or profiling difficult alloys. Controlled chip formation and practical application guidance The MM4 chipbreaker is tuned for secure chip control in sticky and high‑temperature cutting conditions, guiding chips away from the cutting zone and toolholder. The insert’s size 11 and format suit common precision turning setups and allow flexible use across finishing and medium‑cutting depths depending on machine rigidity. As a coated turning insert from Walter Tools’ Tiger‑tec Silver series, it supports efficient material removal while maintaining surface integrity and repeatable performance in production environments. For reliable production with Walter Tools’ Tiger‑tec Silver inserts, contact Metav Werkzeuge for technical guidance and fast supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: DCMT11T304-MM4-WSM01-WALTER Manufacturer: Walter Tools Product type: Turning insert Series: Tiger‑tec Silver Grade: WSM01 Chipbreaker: MM4 Form: Rhombus 55° Execution: T Facts Clearance angle: 7° Corner radius: 0.4 mm Size: 11 Thickness: T3 Tolerance class: M Special features Coated carbide construction Suitable for stainless steels (M) Suitable for heat‑resistant superalloys / titanium (S) Stable edge for high temperatures Optimised chip control FAQ What materials is this insert suitable for? The DCMT11T304-MM4 WSM01 turning insert is formulated for stainless steels and heat‑resistant superalloys (ISO groups M and S), reflecting the WSM01 grade’s focus on heat resistance and edge stability. How does the MM4 chipbreaker affect performance? The MM4 chipbreaker on this Walter Tools insert promotes controlled chip flow and reduced built‑up edge in sticky materials, improving surface finish and operational safety. Which cutting tasks suit the rhombus 55° form? The rhombus 55° geometry provides versatility for general turning and profile work where access and angle of approach are important; combined with the 7° clearance, it reduces rubbing and helps achieve consistent finishes. Is the insert part of a coated series and what is the benefit? Yes, it belongs to the Tiger‑tec Silver series; the coating enhances heat resistance and wear protection, extending cutting edge life in demanding applications. Can the insert be used for finishing and medium cutting? The insert’s geometry and T3 thickness make it appropriate for finishing and medium‑depth cuts when paired with suitable cutting parameters and a rigid setup. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Trademarked names and product designations are the property of their respective owners. Brand names are mentioned for explanation only; there is no affiliation between our company and the named brands. The offered article is an original, factory‑new product of the specified manufacturer, Walter Tools. The Walter AG brand (marketed as Walter Tools) forms part of the global Sandvik group.
DCMT11T304-MM4 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver wear resistance, a precise MM4 chipbreaker and a compact rhombus 55° geometry for consistent performance in demanding turning operations; order the inserts via Metav Werkzeuge or ask the consultants for application advice. DCMT11T304-MM4 WSM10S indexable turning insert, Tiger·tec Silver coating, for stainless steels and superalloys — Walter Tools DCMT11T304-MM4 WSM10S is an indexable turning insert designed for robust machining of stainless steels and heat-resistant superalloys, offering a balance of cutting-edge coating technology and a geometry optimised for stable chip control. Tiger·tec Silver coating for high wear resistance Optimised MM4 chipbreaker for stable chip control Rhombus 55° geometry for versatile turning 7° relief angle for secure cutting engagement 0.4 mm corner radius for precise edge definition Maximise tool life with advanced coating technology The Tiger·tec Silver coated carbide grade WSM10S provides elevated thermal stability and wear resistance in severe cutting conditions. Coated grades extend tool life by reducing abrasion and thermal damage; this is particularly important when working with tough-to-cut materials where heat concentration and adhesion can rapidly degrade the cutting edge. The result is fewer index changes, more predictable wear progression and improved process economy per finished component. Consistent chip control for safer machining The dedicated MM4 chipbreaker has been developed to produce short, controllable chips under a wide range of turning parameters. Effective chip control reduces the risk of built-up edge and protects both the workpiece surface and the tool flank, leading to more reliable cycle times and fewer interruptions. In practice, stable chip formation improves operator safety and simplifies swarf handling in automated environments. Geometry engineered for flexibility and accuracy The rhombus 55° insert shape combined with a 7° relief angle creates a secure cutting engagement and versatile approach directions for external turning. The 0.4 mm corner radius provides an economical compromise between edge strength and surface finish: it supports robust cutting edges for interrupted cuts while maintaining the ability to deliver acceptable surface quality in finishing passes. These geometrical choices make the insert suitable for both semi-finishing and medium-depth finishing operations. Material suitability and reliable edge performance The grade is explicitly targeted at materials in ISO groups M (stainless steels) and S (heat-resistant superalloys and titanium). These materials tend to generate high temperatures and can promote adhesion at the cutting zone; the coated carbide composition of this insert is optimised to maintain a stable cutting edge under these stresses. For manufacturing processes that demand repeatable component quality when machining difficult alloys, the insert provides process security and consistent results. For ordering guidance or application-specific recommendations for Walter Tools DCMT11T304-MM4 WSM10S inserts, please contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: DCMT11T304-MM4-WSM10S-WALTER Label: Drehwendeschneidplatte DCMT11T304-MM4 WSM10S Walter Tools Product type: Indexable turning insert Manufacturer: Walter Tools Series: Tiger·tec Silver Facts Relief angle: 7° Corner radius: 0.4 mm Insert size: 11 Thickness: T3 Geometry: Rhombus 55° Tolerance class: M Special features Coating: Tiger·tec Silver Grade: WSM10S (coated carbide) Chipbreaker: MM4 Material suitability: stainless steels (M), heat-resistant superalloys / titanium (S) Typical applications: demanding turning of tough alloys and stainless materials FAQ What materials is this insert intended for? The DCMT11T304-MM4 WSM10S insert is formulated for ISO material groups M (stainless steels) and S (heat-resistant superalloys and titanium), providing stable edge performance under high thermal loads. How does the MM4 chipbreaker improve machining? The MM4 chipbreaker promotes short, controlled chips that reduce built-up edge and facilitate swarf management, leading to fewer process interruptions and safer turning operations. What are the benefits of the Tiger·tec Silver coating? The Tiger·tec Silver coating enhances thermal resistance and wear protection on the coated carbide substrate, which increases tool life and maintains cutting-edge stability in demanding applications. Is the rhombus 55° geometry suitable for finishing? Yes; the rhombus 55° form, combined with a 0.4 mm corner radius, supports both semi-finish and medium finishing passes while preserving edge strength for interrupted cuts. Can this insert be used for interrupted cuts? The combination of graded coating, geometry and corner radius provides improved resistance to mechanical shock and thermal stress, making this insert suitable for many interrupted cutting scenarios. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and product names are the property of their respective owners. Walter Tools is mentioned for explanation and identification purposes only; there is no affiliation implied between our company and the trademark holders. The offered article is an original, factory-new product of the manufacturer.
DCMT11T304-MM4 WSM20S MM4 Wendeplatten - Walter Tools
Benefit from durable edge life, reliable chip control and a compact rhombic geometry that streamlines turning operations; order through Metav Werkzeuge or contact the consultants for application advice. DCMT11T304-MM4 WSM20S turning insert by Walter Tools — Tiger·tec Silver, MM4 chipbreaker The DCMT11T304-MM4 WSM20S is a rhombic 55° turning insert designed for demanding turning tasks in stainless steels and heat-resistant superalloys. Tiger·tec Silver coating for edge stability WSM20S grade for stainless and superalloys Rhombic 55° shape for versatile turning 0.4 mm corner radius for fine surface finish Consistent edge life for demanding materials The combination of the Tiger·tec Silver coating and the WSM20S grade delivers enhanced heat resistance and a tougher cutting edge, which is particularly important when machining stainless steels and superalloys. These materials tend to produce high cutting temperatures and can promote built-up edge; the coating reduces friction and protects the carbide substrate, resulting in more predictable tool life and fewer unscheduled tool changes. The controlled wear behaviour supports stable production cycles and predictable regrinding intervals. Predictable chip control improves surface quality The integrated MM4 chipbreaker is engineered for secure chip formation under challenging conditions, reducing the risk of long stringy chips and improving evacuation from the cut. Predictable chips help to avoid workpiece damage and secondary finishing, delivering a consistent surface finish with lower scrap rates. In practice, reliable chip control also reduces machine downtime caused by chip entanglement and contributes to safer, more efficient machining. Optimised geometry for secure cutting and versatility The Rhombic 55° form paired with a 0.4 mm corner radius and a 7° rake angle balances cutting forces and surface integrity. A smaller corner radius supports finer finishing operations and tighter dimensional control, while the chosen rake angle aids in effective shear formation when turning tough alloys. The insert’s T3 thickness and tolerance class M ensure stable clamping and repeatable positioning in compatible tool holders, which translates into reduced set-up time and consistent part quality across production batches. Practical integration for dependable process performance Belonging to the Tiger·tec Silver series, the insert is intended for industrial turning applications where repeatability and tool life are priorities. The grade supports machining of ISO group M (stainless) and S (heat-resistant superalloys/titanium), making it suited to job shops and production lines handling these materials. Fitting standard toolholders for the DCMT form, the insert enables seamless integration into existing tool inventories and supports efficient tool management for continuous operation. For tailored cutting data or to check compatibility with specific tool holders, contact Metav Werkzeuge for precise recommendations on the Walter Tools DCMT11T304-MM4 WSM20S turning inserts and availability via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number/SKU: DCMT11T304-MM4-WSM20S-WALTER Label: Drehwendeschneidplatte DCMT11T304-MM4 WSM20S Walter Tools Product type: turning insert Brand: Walter Tools Numbers / Core technical data Plate size: 11 Corner radius: 0.4 mm Rake angle: 7° Plate thickness: T3 Shape: Rhombic 55° Tolerance class: M Designs / Special features Series: Tiger-tec Silver Grade: WSM20S Chipbreaker: MM4 Execution: T Designation: DCMT11T304-MM4 Material suitability: stainless steels (M), superalloys/titanium (S) FAQ Which materials is this insert suitable for? The DCMT11T304-MM4 WSM20S insert by Walter Tools is suitable for stainless steels (ISO group M) and heat-resistant superalloys/titanium (ISO group S), as indicated by its coating and grade. What does the MM4 chipbreaker achieve? The MM4 chipbreaker on the DCMT11T304-MM4 promotes controlled chip formation to improve evacuation, reduce entanglement and support a consistent surface finish when machining difficult materials. How does the 0.4 mm corner radius affect machining? A 0.4 mm corner radius provides a balance between strength and finish: it supports edge robustness for interrupted cuts while enabling finer surface quality compared with larger radii. Is the insert compatible with standard DCMT holders? Yes, the DCMT11T304-MM4 style is compatible with tool holders designed for DCMT-format inserts; correct clamping and tolerance class M ensure repeatable positioning. What advantage does the Tiger·tec Silver series provide? Inserts from the Tiger·tec Silver series, such as this WSM20S grade, offer improved thermal resistance and abrasion properties, which together contribute to longer tool life and stable machining in high-temperature applications. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking. Protected trademarks and product names are the property of their respective owners. The mentioned brand names are used solely for explanation; there is no affiliation between Metav Werkzeuge and the trademark owners. The offered item is an original, brand-new product of the manufacturer.
DCMT11T304-MM4 WSM30S MM4 Wendeplatten - Walter Tools
Take advantage of Tiger·tec Silver performance and the robust WSM30S grade to secure reliable chip control and long tool life in demanding stainless and heat-resistant alloy turning applications; order directly via Metav Werkzeuge or consult the technical team for process-specific recommendations. DCMT11T304-MM4 WSM30S indexable turning insert — Walter Tools, Tiger·tec Silver, for stainless and superalloys A DCMT11T304-MM4 WSM30S indexable insert designed for stable cutting in stainless steels and heat‑resistant superalloys, featuring a rhombic 55° geometry and a specialised MM4 chipbreaker. Tiger·tec Silver coated carbide grade WSM30S Optimised for stainless steel and superalloys Rhombic 55° insert with 7° clearance 0.4 mm corner radius for stable cutting MM4 chipbreaker for secure chip control Maximise cutting reliability with a heat‑resistant grade The WSM30S grade, developed within the Tiger·tec Silver family, is engineered for high thermal stability and reliable edge retention when machining tough workpiece materials. Thanks to the coating chemistry and substrate balance, the insert sustains a consistent cutting edge under elevated temperatures typical of stainless steels and superalloys, which reduces unexpected tool changes and improves process uptime. The measurable outcome is fewer interruptions and a more predictable production cycle. Achieve consistent surface quality and predictable chip formation The MM4 chipbreaker in this geometry promotes secure chip control during continuous and interrupted cuts, limiting built-up edge and minimising surface irregularities. With a 0.4 mm corner radius and 7° clearance, the geometry balances strength and versatility: the edge is robust enough for stable turning while still allowing favourable cutting forces for fine surface finishes. These characteristics translate directly into repeatable components and reduced rework. Versatile geometry for demanding turning tasks The rhombic 55° form offers a flexible approach to facing and turning operations, enabling positive cutting angles for improved feed capability and accessible cutting positions in complex setups. The 11 mm plate size and T3 thickness deliver a compact solution for tight toolholders while maintaining sufficient mass for heat dissipation. This combination makes the insert suitable for shops aiming to streamline tooling variants without sacrificing performance on challenging materials. Integration into production and operational benefits Incorporating these inserts into existing tool systems is straightforward and benefits are measurable: improved edge life, consistent chip control and reduced machine downtime. The insert’s tolerance class M and standard ISO designation ensure compatibility with common turning toolholders and CNC programmes. For customers seeking process optimisation, the technical data supports reliable cycle time estimates and easier parameter transfer between machines. Speak with Metav Werkzeuge for tailored application support on Walter Tools Tiger·tec Silver inserts and ensure optimal cutting parameters for stainless steel and superalloy turning Technical data Article number: DCMT11T304-MM4-WSM30S-WALTER Label: Drehwendeschneidplatte DCMT11T304-MM4 WSM30S Walter Tools Product type: Drehwendeschneidplatte Manufacturer: Walter Tools Series: Tiger-tec Silver Grade: WSM30S Dimensions / Core data Insert form: Rhombus 55° Clearance angle: 7° Corner radius: 0.4 mm Plate size: 11 Thickness: T3 Chipbreaker: MM4 Tolerance class: M Features / Applications Coating: Tiger·tec Silver Substrate: coated carbide (WSM30S) Material suitability: stainless steels and heat‑resistant superalloys Typical use: heavy or thermally demanding turning operations FAQ What materials is this insert intended for? The DCMT11T304-MM4 WSM30S insert is specified for stainless steels and heat‑resistant superalloys, where its coating and geometry enable improved thermal and edge stability. How does the MM4 chipbreaker influence machining? The MM4 chipbreaker promotes controlled chip formation and evacuation, reducing the risk of built‑up edge and improving surface consistency when using this Walter Tools insert. What advantages does the 0.4 mm corner radius provide? A 0.4 mm corner radius offers a compromise between edge strength and surface finish capability, helping to extend tool life while maintaining acceptable component quality. Is the insert compatible with standard toolholders? Yes; the ISO designation and tolerance class M make the insert compatible with common turning toolholder systems designed for rhombic 55° inserts. Can the Tiger·tec Silver coating reduce tool changes? The Tiger·tec Silver coating enhances thermal resistance and wear behaviour, which can lead to longer intervals between tool changes and more consistent production runs. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT11T304-MP4 WEP10C WEP10C Wendeplatten - Walter Tools
Achieve consistent finishing and extended tool life by combining the Walter Cermet grade WEP10C with the MP4 chipbreaker; order the DCMT11T304-MP4 WEP10C directly via Metav Werkzeuge or request application advice from our consultants. DCMT11T304-MP4 WEP10C — Indexable turning insert, Rhombic 55° with 0.4 mm corner radius | Walter Tools The DCMT11T304-MP4 WEP10C is a cermet indexable turning insert optimised for finish turning and stable cutting behaviour in precision production environments. Walter Cermet grade WEP10C MP4 chipbreaker for controlled chips Rhombic 55° form with 0.4 mm radius 7° clearance and T3 plate thickness Consistent surface quality through cermet performance The Walter Cermet WEP10C grade offers a hard, wear-resistant cutting edge that supports high-quality finishing. As a cermet material, it combines ceramic hardness with metallic toughness to resist flank wear while producing fine surface textures. The small 0.4 mm corner radius helps to maintain repeatable part geometry and reduce the need for secondary finishing, which contributes to shorter production cycles and fewer rework steps. Controlled chip formation for reliable production Equipped with the MP4 chipbreaker, the insert ensures effective chip control across a range of feed rates. The chipbreaker is designed to promote short, manageable chips that are removed consistently, reducing the risk of surface damage and machine downtime. Improved chip behaviour leads to enhanced process stability, which is especially valuable in automated or lights-out machining where unattended reliability is essential. Geometry tailored for versatile turning operations The Rhombic 55° insert form with a 7° clearance angle provides a balance between strength and access to intricate contours. The geometry supports both light finishing cuts and moderate machining steps where edge stability is required. The T3 plate thickness and M tolerance class contribute to predictable clamping behaviour and repeatable positioning in the toolholder, simplifying setup and reducing cycle-to-cycle variation. Application guidance and material fitment Designed within the Walter Cermet series, the cutting grade and chipbreaker combination is intended for users seeking improved surface finish and longer edge life in high-precision turning. Material suitability should be confirmed against the product matrix; the insert’s Cermet composition typically excels in finishing steels and alloyed materials where thermal stability and low chemical affinity at the cutting edge are required. For specific substrates or hard-to-machine alloys, trial cuts and parameter adjustments are advised to exploit the grade’s strengths. For technical advice on applying the Walter Tools DCMT11T304-MP4 WEP10C insert or to check stock and suitability, contact Metav Werkzeuge—email info@metav-werkzeuge.com or call +49 2822 7131930 for prompt consultation and order placement. Technical data Article number: DCMT11T304-MP4-WEP10C-WALTER Name: Drehwendeschneidplatte DCMT11T304-MP4 WEP10C Walter Tools Series: Walter Cermet Grade: WEP10C ISO designation: DCMT11T304-MP4 WEP10C Facts Plate size: 11 Corner radius: 0.4 mm Clearance angle: 7° Plate thickness: T3 Tolerance class: M Special features Chipbreaker: MP4 Cutting material type: Cermet Plate form: Rhombic 55° Execution: T FAQ What machining tasks is this insert suited for? The DCMT11T304-MP4 WEP10C insert from Walter Tools is geared towards finish turning and operations where high surface quality and stable cutting edges are required. How does the MP4 chipbreaker affect machining? The MP4 chipbreaker on the DCMT11T304-MP4 WEP10C promotes short, controllable chips and improved process stability, which reduces risk of damage and supports higher uptime. Is the WEP10C grade suitable for hard turning? WEP10C is a cermet grade optimised for finishing; suitability for harder materials should be checked against the product matrix and validated with trial cuts. Can this insert be used for roughing operations? While primarily designed for finishing, the insert’s geometry and grade can handle moderate cuts, but aggressive roughing may require a different chipbreaker or grade for optimal life. What are the key dimensions to consider when selecting a toolholder? Match the Rhombic 55° form, plate size 11, thickness T3, and M tolerance class to the toolholder specification to ensure correct seating and clamping. Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names are the property of their respective owners. Mark names and protected designations are mentioned for explanation only. The item offered is an original, factory-new product of the manufacturer. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DCMT11T304-MP4 WPP10G WPP10G Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Gold coating, an MP4 chipbreaker and a robust rhombic 55° geometry to improve tool life and process stability in steel turning; order the insert directly via Metav Werkzeuge or ask our consultants for application support. DCMT11T304-MP4 WPP10G — Indexable turning insert, Tiger‑tec Gold, rhombic 55° (Walter Tools) A DCMT11T304-MP4 WPP10G indexable turning insert engineered for dependable steel machining with optimised chip control. Tiger‑tec Gold coating for long tool life MP4 chipbreaker for controlled chip flow Rhombic 55° geometry for versatile turning 7° clearance with 0.4 mm corner radius Extended life and consistent performance for steel turning The combination of the Tiger‑tec Gold coating and the WPP10G grade delivers a measurable improvement in wear resistance and thermal stability during steel machining. The coated carbide substrate reduces flank wear under typical turning temperatures, while the coating design supports stable edge retention, which in turn lowers the frequency of insert changes. This means more uninterrupted production and predictable batch outcomes for medium- to high-volume turning operations, especially when working within the ISO P material group. Reliable chip control that boosts productivity Featuring the MP4 chipbreaker, this insert offers controlled chip formation across a broad range of cutting parameters. The chipbreaker geometry reduces the risk of snarled or long chips, facilitating safer automated handling and minimizing downtime for chip clearing. Effective chip control combined with the insert’s rhombic geometry contributes to consistent surface finish and repeatable cycle times, supporting leaner machining processes and improved throughput. Practical geometry for versatile applications The rhombic 55° shape with a 7° clearance angle and a 0.4 mm corner radius provides a balance between strength and accessibility in a variety of turning tasks. The geometry suits finishing and light to medium roughing passes on steels, enabling stable edge engagement and predictable cutting forces. The insert’s T3 thickness and the specified tolerance class ensure mechanical stability in typical clamping systems, making it a practical choice for operators aiming for both precision and robustness on conventional and CNC lathes. Clear technical advantages and operational benefits Selecting this indexable insert supports cost-effective machining through reduced tool consumption and reliable performance across diverse steel grades. The combination of a wear‑resistant coating, a proven chipbreaker and a balanced insert form helps to lower scrap rates and improve surface quality, which is particularly valuable in batch production and when tolerances are tight. For shops seeking a reliable turning solution for ISO P, this insert offers a strong ratio of longevity to process security. Contact Metav Werkzeuge for availability, application advice and to secure Tiger‑tec Gold inserts from Walter Tools; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: DCMT11T304-MP4-WPP10G-WALTER Designation: DCMT11T304-MP4 WPP10G Manufacturer: Walter Tools Series: Tiger‑tec Gold Grade: WPP10G Product type: Indexable turning insert Facts Clearance angle: 7° Corner radius: 0.4 mm Plate size: 11 Thickness: T3 Tolerance class: M Special features Coating: Tiger‑tec Gold (coated carbide) Chipbreaker: MP4 Geometry: Rhombic 55° Material group: Steel (ISO P) Suitable for turning operations on unalloyed and alloyed steels FAQ What materials is this insert optimised for? The DCMT11T304-MP4 WPP10G insert is optimised for the ISO P material group, specifically unalloyed and alloyed steels, according to the grade characteristics of WPP10G. How does the MP4 chipbreaker affect machining? The MP4 chipbreaker promotes controlled chip formation and reduces the likelihood of long, tangled chips, improving process reliability and safety during automated turning operations. Is the insert suitable for finishing and roughing passes? With a rhombic 55° form, a 0.4 mm corner radius and robust coating, the insert suits finishing and light to medium roughing on steels, offering a compromise between edge strength and access to the workpiece. Can this insert withstand elevated cutting temperatures? The Tiger‑tec Gold coating enhances thermal stability and wear resistance during typical turning temperatures encountered when machining steel, contributing to longer insert life. Which series and grade should be ordered for general steel turning? Order the DCMT11T304-MP4 in grade WPP10G from the Tiger‑tec Gold series for a balanced, high‑productivity solution in steel machining. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected product names are mentioned solely for explanatory purposes. There is no connection between our company and the mentioned brands. The offered item is original, factory‑new merchandise from the manufacturer (Walter Tools).
DCMT11T304-MP4 WPP20G MP4 Wendeplatten - Walter Tools
Order a robust turning solution that combines Tiger·tec Gold coating and the MP4 chipbreaker for extended tool life and controlled chip formation; ideal for steady steel machining in production environments — order directly via Metav Werkzeuge or consult their specialists for integration advice. DCMT11T304-MP4 WPP20G Turning insert, Tiger·tec Gold, for steel — Walter Tools The DCMT11T304-MP4 WPP20G is a rhombic 55° turning insert designed for precision steel turning, combining Tiger·tec Gold coating with an MP4 chipbreaker for reliable chip control in industrial turning applications Tiger·tec Gold coating for high wear resistance MP4 chipbreaker for controlled chip formation Rhombic 55° geometry for versatile turning Corner radius 0.4 mm for edge stability Longer tool life through advanced coating technology The Tiger·tec Gold coating delivers enhanced wear resistance and thermal stability, which reduces flank wear under typical steel cutting conditions. By lowering friction at the cutting zone, the coated grade allows for higher productivity and fewer indexings, translating into longer uninterrupted production runs. This effect is particularly relevant for batch machining where frequent tool changes interrupt throughput. The coating’s behaviour with unalloyed and alloyed steel makes it suitable for a broad range of workshop applications while supporting consistent dimensional results. Controlled chip formation for safer, more efficient turning The integrated MP4 chipbreaker is engineered to produce predictable chips and promote smooth evacuation, which improves process safety and reduces downtime related to chip entanglement. In practice, the chip geometry helps maintain stable cutting forces and contributes to a consistent surface finish. For shops focused on throughput, this means fewer manual interventions and better machine availability. The chip control feature is also advantageous when turning long or thin-walled components where chip management is critical. Geometry and edge preparation for stable cutting performance With a rhombic 55° insert form, 7° clearance angle and a 0.4 mm corner radius, the geometry balances strength and accessibility in a single design. The modest corner radius provides robust edge support to withstand intermittent cuts and interrupted machining, while the 55° shape offers favourable approach angles for external turning and light profiling operations. These geometric choices result in a stable cutting edge that supports repeatable results and predictable tool life under varied cutting parameters. Application fit and process integration for steel machining Specifically formulated for machining steel, the grade delivers dependable chip behaviour and repeatable performance across typical workshop processes. The insert’s tolerance class M and the standard designation simplify toolholder selection and programme setup in production environments. For operations seeking a pragmatic trade-off between wear resistance and toughness, this grade offers the consistency required for series production while enabling efficient tool management and stock planning in the tooling cabinet. Choose Walter Tools Tiger·tec Gold inserts via Metav Werkzeuge for a durable steel turning solution — contact Metav Werkzeuge for technical matching and order processing at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: DCMT11T304-MP4-WPP20G-WALTER Name: DCMT11T304-MP4 WPP20G Manufacturer: Walter Tools Product type: Turning insert Facts Plate form: Rhombus 55° Clearance angle: 7° Corner radius: 0.4 mm Plate size: 11 Plate thickness: T3 Tolerance class: M Special features Coating: Tiger·tec Gold Grade: WPP20G Chipbreaker: MP4 Material application: Steel (P) Series: Tiger·tec Gold FAQ Which materials is this insert designed for? The DCMT11T304-MP4 WPP20G grade is designed primarily for machining steel (designation P), offering suitable wear behaviour for unalloyed and alloyed steels. What advantages does the Tiger·tec Gold coating provide? Tiger·tec Gold on the DCMT11T304-MP4 WPP20G reduces friction and improves thermal stability, resulting in longer tool life and more consistent performance in steel turning. How does the MP4 chipbreaker influence machining? The MP4 chipbreaker produces controlled chips and aids evacuation, which improves process safety and reduces interruptions during turning operations with the DCMT11T304-MP4 WPP20G insert. What cutting geometry should be expected from this insert? The insert offers a rhombic 55° form, 7° clearance and a 0.4 mm corner radius, providing a balance of accessibility and edge strength for external turning tasks. Is the insert suitable for interrupted cuts or roughing operations? Yes, the 0.4 mm corner radius and Tiger·tec Gold coating provide edge robustness that supports interrupted cutting and many roughing applications on steel. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade designations are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered item is an original, factory-new product of the manufacturer.
DCMT11T304-MP6 WPP10G MP6 Wendeplatten - Walter Tools
Take advantage of the combination of precision geometry, reliable chip control and Tiger·tec Gold coating for consistent machining of steel; order directly via Metav Werkzeuge or request technical advice from the consultants. DCMT11T304-MP6 WPP10G turning insert — MP6 chipbreaker, Tiger·tec Gold coating — Walter Tools DCMT11T304-MP6 WPP10G is an indexable turning insert optimised for steel machining with balanced wear resistance and predictable chip formation Tiger·tec Gold coated carbide WPP10G MP6 chipbreaker for controlled chip formation 7° clearance and 0.4 mm corner radius Suitable for steel machining (ISO P) Predictable chip control for stable production The combination of Tiger·tec Gold coating and the MP6 chipbreaker delivers enhanced chip control and extended tool life when machining steels. The coated carbide formulation is engineered for the heat and deformation patterns typical in ISO P applications, which results in more uniform flank wear and reduced edge chipping. This reliability supports steady cycle times and fewer unplanned tool changes, improving throughput in series production environments. Geometry designed for consistent surface quality A rhombus 55° insert form with 0.4 mm corner radius and 7° clearance offers a balance between strength at the cutting edge and the ability to produce fine surface finishes. The thickness designation T3 and the tolerance class M indicate stable seating in the pocket and repeatable positioning, which is important for maintaining dimensional accuracy across batches. These geometric details translate into predictable part quality, especially during finishing and light to medium turning operations. Integration and performance in workshop workflows Rated for steel (ISO P) use and supplied under the Tiger·tec Gold series, this indexable insert supports a broad range of applications from standard turning to more demanding operations requiring a mix of wear resistance and toughness. The insert’s designation and chipbreaker geometry simplify cutting-data selection and tool management in production systems. Backed by Walter Tools’ engineering heritage, the component contributes to process continuity and consistent results in daily machining tasks. For application guidance, batch supply or to purchase the DCMT11T304-MP6 WPP10G insert, contact Metav Werkzeuge for tailored advice and delivery options at info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: DCMT11T304-MP6-WPP10G-WALTER Label: Drehwendeschneidplatte DCMT11T304-MP6 WPP10G Walter Tools Series: Tiger-tec Gold Grade/sort: WPP10G Manufacturer: Walter Tools Product type: Drehwendeschneidplatte Facts Free angle: 7° Corner radius: 0.4 mm Size designation: 11 Thickness: T3 Tolerance class: M Special features Coating: Tiger·tec Gold (coated carbide) Chipbreaker: MP6 Insert form: Rhombus 55° Suitability: Steel (ISO P) Execution/form: T FAQ What materials is this insert designed for? The DCMT11T304-MP6 WPP10G insert is specified for machining steels (ISO P); the WPP10G grade is optimised for the thermal and chip-formation behaviour typical of steel. Which chipbreaker does the insert use and what is the benefit? This insert features the MP6 chipbreaker; it provides controlled chip formation and evacuation, supporting stable cutting and reduced risk of built-up edge during turning. What are the key geometry parameters that affect finish quality? The rhombus 55° form, 0.4 mm corner radius and 7° clearance contribute to edge strength and the ability to achieve consistent surface finishes in finishing and light to medium turning. Is this insert compatible with standard toolholders? The DCMT11T304-MP6 format follows common indexable insert conventions; tolerance class M and the T3 thickness support secure seating in pockets designed for this shape and size. What performance advantages does the Tiger·tec Gold series offer? Tiger·tec Gold coating enhances wear resistance and thermal stability on coated carbide grades like WPP10G, improving tool life and process reliability in serial machining of steel. The Walter AG (marketed as Walter Tools) with headquarters in Tübingen is among the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik group. Protected trademarks and product names are the property of their respective owners and are mentioned here for descriptive purposes only; there is no affiliation implied between Metav Werkzeuge and these manufacturers. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com