DCMT11T304-MP6 WPP20G Wendeplatten - Walter Tools
Benefit from the combination of the Tiger·tec Gold coating and the WPP20G grade for productive turning: the MP6 chipbreaker promotes stable chip control while the 7° clearance supports consistent cutting action and extended tool life. Order the DCMT11T304-MP6 WPP20G insert directly via Metav Werkzeuge or consult their specialists for application-specific advice. DCMT11T304-MP6 WPP20G — Turning insert with MP6 chipbreaker, Tiger·tec Gold by Walter Tools The DCMT11T304-MP6 WPP20G is a rhombic 55° turning insert designed for general steel turning, offering a fine balance between wear resistance and toughness for reliable, repeatable machining. Tiger·tec Gold coating for longer tool life WPP20G grade optimised for steel machining MP6 chipbreaker for predictable chip control Rhombus 55° form with 0.4 mm corner radius Consistent performance for steel turning operations The combination of the Tiger·tec Gold coating and the WPP20G grade provides a measured increase in wear resistance without sacrificing edge robustness. For components machined from steel, this insert delivers coated carbide durability while maintaining a cutting edge that resists chipping under interrupted cuts. The geometry of the insert and the MP6 chipbreaker reduce the risk of built-up edge and help to preserve tool life, which in turn reduces downtime and contributes to more predictable cycle times. Controlled chip formation and improved surface quality The MP6 chipbreaker is engineered to produce short, controllable chips in a wide range of turning conditions, which simplifies chip evacuation and enhances operator safety. With the Rhombus 55° form and a 0.4 mm corner radius, the insert supports stable tool engagement and consistent surface finishes on turned parts. The modest 7° clearance angle helps to minimise rubbing and heat generation, translating into more consistent dimensional results and fewer secondary operations. Process reliability and economical machining Designed as a universal solution for many steel applications, the insert’s WPP20G cutting material offers a favourable balance between toughness and wear resistance, enabling longer tool life in mixed-machining environments. The standardised base designation ensures easy integration into existing toolholders, and the repeatable geometry supports predictable tool-change planning. For operations aiming to combine productivity with component quality, this insert reduces the need for frequent tool changeovers and helps to improve overall process economy. Contact Metav Werkzeuge today to discuss how the Walter Tools DCMT11T304-MP6 WPP20G turning insert can be matched to specific steel applications for optimal productivity and surface quality Technical data Article number: DCMT11T304-MP6-WPP20G-WALTER Designation: DCMT11T304-MP6 WPP20G Manufacturer: Walter Tools Product type: Turning insert Facts Inscribed size: 11 Corner radius: 0.4 mm Clearance angle: 7° Thickness: T3 Tolerance class: M Plate form: Rhombus 55° Special features Chipbreaker: MP6 Series: Tiger·tec Gold Grade: WPP20G (coated carbide) Base designation: DCMT11T304-MP6 Suitable for: steel FAQ What materials is this insert suitable for? The DCMT11T304-MP6 WPP20G insert is specified for machining steel and was developed with the WPP20G grade to handle the heat and chip patterns typical of steel turning. How does the MP6 chipbreaker affect machining? The MP6 chipbreaker produces short, controllable chips and improves evacuation, which supports safer and more reliable turning processes with consistent surface quality. What does the Rhombus 55° form mean for toolholders? A rhombic 55° geometry provides versatile engagement angles suitable for standard turning toolholders compatible with the DCMT designation. Is the insert suitable for finishing operations? With a 0.4 mm corner radius and the Tiger·tec Gold coating, the insert can achieve good surface quality in semi-finishing and finishing passes, depending on cutting parameters and workpiece condition. Which series and grade does this insert belong to? This item is part of the Tiger·tec Gold series and uses the WPP20G grade, which is a coated carbide composition optimised for steel machining. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade marks are mentioned solely for explanatory purposes. There is no connection between our company and the named brands. The offered article is an original, brand-new product of the manufacturer (Walter Tools).
DCMT11T304-MP6 WPP30G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold wear resistance, an MP6 chipbreaker for reliable chip control and the versatile rhombic 55° geometry to keep turning operations productive and cost‑effective; order directly via Metav Werkzeuge or contact the consultants for tailored cutting data. DCMT11T304‑MP6 WPP30G turning insert — Tiger‑tec Gold for steel (Walter Tools) The DCMT11T304‑MP6 WPP30G is a coated carbide turning insert designed for general steel machining, offering a balance of wear resistance and reliable chip formation in a compact rhombic format. Tiger‑tec Gold coating for extended life Optimised MP6 chipbreaker for stable chips Rhombic 55° form for versatile turning 0.4 mm corner radius for fine surface finish Longer tool life through advanced coating technology The Tiger‑tec Gold coating and coated carbide substrate form the core of the cutting grade, delivering significantly improved wear resistance under the thermal and mechanical loads typical of steel machining. This combination reduces the frequency of insert changes and contributes to a lower cost per part, which supports continuous production runs and predictable tool planning. The grade is engineered to cope with the heat generation and chip formation patterns of ISO P materials, enabling a more efficient machining cycle. Predictable chip control for safer, faster turning Equipped with the MP6 chipbreaker, the insert provides controlled chip splitting and evacuation, reducing the risk of snagging and tool interference. The engineered groove geometry breaks chips into compact shapes, improving process reliability and allowing higher feed rates where appropriate. Stable chips improve workplace safety and reduce rework, making the insert suitable for demanding series production where consistent performance and reduced downtime are priorities. Geometry that balances versatility and surface quality The rhombic 55° shape with a 0.4 mm corner radius and 7° clearance offers a flexible compromise between strength and accessibility. The indexed rhombic form is well suited to general turning operations, internal profiling and facing, while the small corner radius contributes to a fine surface finish on machined components. The geometry supports both roughing with controlled stock removal and light finishing passes without frequent tool changes. Practical data and application guidance for reliable selection Tolerance class M and the T3 thickness ensure repeatable location and secure clamping in standard toolholders sized for insert designation 11. The grade WPP30G is optimised for steel (ISO P), providing a versatile option across unalloyed and alloyed steels where a balance of wear resistance and toughness is required. For process planning, the insert’s stable performance characteristics support predictable cycle times and easier integration into existing machining strategies, helping to raise overall workshop productivity. Contact Metav Werkzeuge for application support, availability and cutting data specific to the Tiger‑tec Gold DCMT11T304‑MP6 WPP30G turning insert — Metav Werkzeuge is available at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: DCMT11T304-MP6-WPP30G-WALTER SKU: DCMT11T304-MP6-WPP30G-WALTER Product type: Turning insert (indexable) Facts Corner radius: 0.4 mm Relief angle: 7° Insert size: 11 Thickness: T3 Form angle: Rhombic 55° Special features Coating: Tiger‑tec Gold Grade: WPP30G (coated carbide) Chipbreaker: MP6 Tolerance class: M Application group: Steel (ISO P) FAQ What materials is this insert suitable for? The DCMT11T304‑MP6 WPP30G turning insert is designed for ISO P materials, specifically unalloyed and alloyed steel, and the grade composition targets the typical heat and chip characteristics of such workpieces. How does the MP6 chipbreaker affect machining? The MP6 chipbreaker produces compact, controlled chips that improve evacuation and reduce the risk of tool interference, which helps to maintain steady feeds and enhances process reliability during turning. What surface finish can be expected with a 0.4 mm corner radius? A 0.4 mm corner radius provides a fine surface finish on finishing passes while still offering sufficient edge strength for moderate stock removal, making the insert suitable for operations that require a balance of finish and durability. Is this insert compatible with standard DCMT toolholders? Yes, the DCMT11T304‑MP6 designation corresponds to standard DCMT toolholder interfaces; the T3 thickness and tolerance class M ensure consistent seat and clamping in compatible holders. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no affiliation between our company and the named brands. The offered item is original and factory‑new from Walter Tools.
DCMT11T304-MW4 WKK10S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the WKK10S grade for highly productive cast iron turning: long tool life and stable chip control reduce downtime and increase throughput. Order the DCMT11T304-MW4 WKK10S directly via Metav Werkzeuge or ask the consultants for cutting data and application advice. DCMT11T304-MW4 WKK10S – Rhombic 55° indexable insert for cast iron by Walter Tools The DCMT11T304-MW4 WKK10S is a rhombic turning insert designed for efficient, reliable machining of cast iron components in industrial turning applications. Tiger·tec Silver coating for enhanced wear resistance Optimised for cast iron applications (ISO K) Rhombic 55° form, 11 mm size for stable cutting MW4 chipbreaker ensures consistent chip control Increased productivity through tailored coating and grade The combination of the Tiger·tec Silver series and the WKK10S cutting grade delivers a robust, coated carbide solution optimised for abrasive cast iron workpieces. The coating technology reduces flank and crater wear, which translates into longer in‑service lifetimes and fewer tool changes. For production environments this means improved machine uptime and a clearer cost-per-part calculation. The insert’s design supports predictable wear progression, allowing process planners to schedule maintenance with greater confidence. Reliable chip control and surface quality Equipped with the MW4 chipbreaker and a Rhombic 55° geometry, the insert promotes controlled chip formation when turning grey or nodular cast iron. The chipbreaker directs short, breakable chips away from the cutting zone, reducing the risk of entanglement and machine stoppages. The moderate 0.4 mm corner radius and the plate’s stable 11 mm size contribute to consistent surface finish and dimensional stability, particularly on interrupted cuts and roughing operations where chip behaviour can be critical. Consistent process security for industrial turning With a tolerance class M and a T3 plate thickness, the insert is manufactured to dimensional standards that support reproducible clamping and interchangeability. The coated carbide composition and series characteristics make the insert suitable for medium to demanding cast iron turning, balancing wear resistance and toughness. Operators and process engineers benefit from reduced variability in tool life and more predictable cycle times, which supports efficient production planning and quality control. Contact Metav Werkzeuge for tailored cutting parameters and ordering of the DCMT11T304-MW4 WKK10S from Walter Tools Technical data SKU: DCMT11T304-MW4-WKK10S-WALTER Designation: DCMT11T304-MW4 WKK10S Manufacturer: Walter Tools Product type: Indexable turning insert Series: Tiger·tec Silver Grade: WKK10S Numbers / Core technical data Free cutting angle: 7° Corner radius: 0.4 mm Plate size: 11 mm Plate thickness: T3 Geometry: Rhombic 55° Tolerance class: M Special features Coating: Tiger·tec Silver (coated carbide) Chipbreaker: MW4 Optimised for: Cast iron (ISO K) Application focus: Turning of cast iron components Form and style: Rhombic 55° indexable insert FAQ Which materials is this insert intended for? The DCMT11T304-MW4 WKK10S from Walter Tools is optimised for machining cast iron (ISO group K) and is designed to handle the abrasive wear typical of those materials. What does the MW4 chipbreaker achieve? The MW4 chipbreaker on the DCMT11T304-MW4 WKK10S controls chip formation to produce short, easily managed chips, improving process reliability and reducing the risk of chip-related interruptions. What are the key geometry and size details? The insert features a Rhombic 55° form, an 11 mm plate size, a 0.4 mm corner radius and a T3 plate thickness, providing stable cutting and consistent surface quality in turning operations. Is the grade coated and what benefits does it bring? Yes, the WKK10S grade is a coated carbide in the Tiger·tec Silver series; the coating enhances wear resistance and helps extend tool life during abrasive cast iron machining. What does the tolerance class M indicate? Tolerance class M denotes a medium dimensional tolerance, supporting reliable interchangeability and consistent clamping in industrial toolholders for the DCMT11T304-MW4 WKK10S. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT11T304-MW4 WKK20S Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Silver coating and the WKK20S carbide grade for reliable, economical turning of cast iron; the Rhombus 55° geometry with MW4 chipbreaker delivers consistent short-chip performance and reduced edge wear. Order the DCMT11T304-MW4 WKK20S directly via Metav Werkzeuge or ask the consultants for application-specific advice. DCMT11T304-MW4 WKK20S turning insert — Tiger‑tec Silver, optimised for cast iron, Walter Tools The DCMT11T304-MW4 WKK20S is a coated carbide turning insert designed for productive machining of cast iron with emphasis on stable chip control and long tool life. Tiger‑tec Silver coated carbide grade WKK20S Optimised for abrasive cast iron machining Rhombus 55° geometry for secure clamping 0.4 mm corner radius and 7° clearance angle Coating and grade engineered for abrasive cast iron The Tiger‑tec Silver coating combined with the WKK20S carbide grade has been developed for the abrasive nature of cast iron. The coating reduces flank and crater wear by improving thermal resistance and reducing built‑up edge formation, which results in longer edge life and more predictable tool changes. For industrial turning operations where frequent interruptions are costly, the enhanced wear resistance translates into a measurable improvement in uptime and consistent surface quality on cast components. Geometry and chip control for uninterrupted productivity The Rhombus 55° form together with the MW4 chipbreaker produces short, controllable chips when turning cast iron, preventing entanglement and improving evacuation from the cut. The 0.4 mm corner radius stabilises the cutting edge for fine finishing passes while the 7° clearance angle helps maintain cutting geometry under load. This combination yields stable cutting forces, fewer rework operations and reliable component tolerances in series production. Mechanical compatibility and handling advantages With a T3 plate thickness and tolerance class M, the insert offers robust clamping security in standard heads designed for rhombic 55° inserts. The ISO-style designation facilitates quick matching with toolholders and reduces setup errors on the shop floor. The turning insert is a useful option for firms seeking straightforward retrofitting into existing toolholder inventories without the need for special adapters, supporting production flexibility. Application focus and operational benefits Specifically tailored for the K material group, the insert excels on grey and nodular cast irons where frequent short chips and abrasive wear define process requirements. The design promotes repeatable surface finish and dimensional stability across batch runs. For manufacturing engineers, the technical combination means fewer tool changes, consistent part quality and improved process reliability — valuable in both jobbing and high-volume environments. Contact Metav Werkzeuge for application guidance and availability of the DCMT11T304-MW4 WKK20S turning insert; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: DCMT11T304-MW4-WKK20S-WALTER Description: DCMT11T304-MW4 WKK20S turning insert, Tiger‑tec Silver, Walter Tools Manufacturer: Walter Tools Series: Tiger‑tec Silver Facts Clearance angle: 7° Corner radius: 0.4 mm Plate form: Rhombus 55° Plate size: 11 Plate thickness: T3 Tolerance class: M Special features Coating: Tiger‑tec Silver (coated carbide) Grade: WKK20S Chipbreaker: MW4 Material suitability: cast iron (K) Application focus: short chips, abrasive wear resistance FAQ What materials is this insert intended for? The DCMT11T304-MW4 WKK20S turning insert is optimised for cast iron machining (ISO group K) and designed to cope with abrasive wear and short, breaking chips. How does the MW4 chipbreaker affect performance? The MW4 chipbreaker on this Walter Tools insert promotes short, well‑controlled chips that improve evacuation and reduce the risk of re‑cutting, aiding process stability in cast iron turning. Is this insert compatible with standard toolholders for 55° rhombic inserts? Yes. The rhombus 55° form and T3 thickness conform to common toolholder geometries for 55° inserts, enabling straightforward integration into existing setups. What benefits does the Tiger‑tec Silver coating provide? The Tiger‑tec Silver coating on the WKK20S grade enhances thermal and abrasion resistance, extending cutting edge life and maintaining surface quality across batch runs. Can this insert be used for finishing as well as roughing? The 0.4 mm corner radius provides edge stability suitable for fine finishing passes, while the overall geometry and grade support productive roughing of cast iron. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names remain the property of their respective owners. Walter Tools and related brand designations are mentioned for clarification; the offered article is an original, factory‑new product of the manufacturer.
DCMT11T304-MW4 WPP10G WPP10G Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Gold coating, the MW4 chipbreaker and a 0.4 mm corner radius for consistent steel turning with dependable chip control; order the insert directly via Metav Werkzeuge or consult our specialists for application support. DCMT11T304-MW4 WPP10G turning insert for steel — Walter Tools, Tiger‑tec Gold, MW4 chipbreaker The DCMT11T304-MW4 WPP10G is an indexable rhombic 55° turning insert designed for efficient machining of steel, offering a balanced grade for wear resistance and toughness and optimised for productive turning operations. Tiger‑tec Gold coating for extended tool life MW4 chipbreaker for reliable chip control Rhombic 55° geometry for versatile turning 0.4 mm corner radius with 7° relief Prolonged tool life through advanced coating and grade The combination of the Tiger‑tec Gold coating and the WPP10G grade delivers a reliably long tool life in steel machining by reducing abrasive wear and stabilising the cutting edge. This coating technology is engineered to withstand the thermal and mechanical stresses typical for P‑group materials, so the insert maintains cutting performance over extended cycles. For production environments this translates into fewer indexings and lower tool-change frequency, which supports predictable process planning and improved overall equipment effectiveness. Predictable chip formation and better surface quality A dedicated MW4 chipbreaker and the rhombic 55° geometry ensure controlled chip flow across a wide range of turning depths and feeds. The chipbreaker design promotes short, segmented chips on standard steel grades, reducing the risk of entanglement and allowing safer automated handling. Combined with the 0.4 mm corner radius, the insert helps to achieve consistent surface finish and dimensional stability on turned components, which benefits finishing steps and reduces rework. Robust geometry for stable cutting and tool clamping The insert’s 7° relief and T3 thickness provide mechanical stability at the cutting edge while helping to dissipate cutting forces into the toolholder. The size 11 dimension and rhombic form make the insert compatible with common turning toolholders for DCMT‑type inserts, offering flexibility across various lathe setups. This geometry supports both interrupted and continuous cuts in steel, giving machine shops the balance between edge strength and precision required for repeatable results. Application guidance and process fit for steel turning Designed specifically for steel under ISO group P, the insert suits a broad spectrum of unalloyed and alloyed steels encountered in general machining. Its balanced properties between wear resistance and toughness make it suitable for standard production turning, from roughing with heavy engagement to semi‑finishing passes. For tailored cutting parameters or to match the insert to a particular toolholder and machining strategy, Metav Werkzeuge’s consultants can provide application‑oriented recommendations based on the component material and cycle demands. Contact Metav Werkzeuge for tailored machining advice on Walter Tools Tiger‑tec Gold inserts and request the DCMT11T304-MW4-WPP10G-WALTER to secure optimal steel turning performance Technical Data Article number: DCMT11T304-MW4-WPP10G-WALTER Label: Drehwendeschneidplatte DCMT11T304-MW4 WPP10G Walter Tools Manufacturer: Walter Tools Product type: Drehwendeschneidplatte Series: Tiger‑tec Gold Facts Relief angle: 7° Corner radius: 0.4 mm Insert size: 11 Thickness: T3 Insert shape: Rhombic 55° Tolerance class: M Special features Coating/technology: Tiger‑tec Gold Chipbreaker: MW4 Grade: WPP10G Application: Steel (ISO P) Execution: T FAQ Which materials is this insert suitable for? The DCMT11T304-MW4 WPP10G is designed for machining steel in accordance with ISO P classifications, covering typical unalloyed and alloyed steels. What advantages does the Tiger‑tec Gold coating provide? Tiger‑tec Gold on the WPP10G grade enhances wear resistance and edge stability under thermal and mechanical loads, extending effective cutting life on steel. How does the MW4 chipbreaker affect machining? The MW4 chipbreaker supports predictable, segmented chip formation and improved evacuation, reducing chip interference and aiding automated machining processes. Which toolholders accept this insert type? Toolholders designed for DCMT‑style rhombic 55° inserts and size 11 clamping systems are compatible; the insert’s geometry and thickness match common turning holders. Is the insert suitable for interrupted cuts and finishing operations? Yes, the balanced grade and the 0.4 mm corner radius allow the insert to perform reliably in both interrupted and finishing passes on steel, offering a compromise between edge strength and surface quality. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no affiliation between Metav Werkzeuge and Walter Tools. The offered article is original factory‑new merchandise of the manufacturer.
DCMT11T304-MW4 WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating, optimised MW4 chip control and a compact Rhombic 55° geometry for reliable turning of Stahl; order directly via Metav Werkzeuge or contact our consultants for machining advice. DCMT11T304-MW4 WPP20G — Turning insert DCMT11T304-MW4 WPP20G for Stahl, Tiger‑tec Gold, Walter Tools A DCMT11T304-MW4 WPP20G indexable turning insert engineered for efficient, repeatable machining of Stahl in finishing and light-medium turning applications. Tiger‑tec Gold coated carbide grade WPP20G Optimised MW4 chipbreaker for controlled chips Rhombic 55° form with 0.4 mm corner radius 7° relief angle for stable cutting edges Consistent productivity through advanced coating and grade The coated carbide Tiger‑tec Gold grade delivers a balanced combination of wear resistance and toughness. Designed specifically for machining Stahl (ISO group P), the grade WPP20G offers a universal performance profile that suits varied alloy contents and temperatures encountered during turning. This balance reduces microchipping and extends edge life, which translates into fewer indexings and steadier cycle times on production runs. By favouring durability over marginal higher-speed settings, the grade supports predictable tool life and consistent part quality, improving process planning and cost-efficiency. Predictable chip formation and surface quality with MW4 The integrated MW4 chipbreaker shapes and controls chip flow to support safe evacuation and stable cutting conditions. For finishing passes, the chip control contributes to improved surface integrity and reduces rework. The chipbreaker geometry reduces the risk of entanglement in interrupted cuts and supports a steady contact pattern between insert and workpiece. For workshops seeking process security, the result is fewer stoppages and a cleaner machining environment, while maintaining the dimensional stability expected from a precision insert. Geometry engineered for strength and repeatability The Rhombic 55° form combined with a 0.4 mm corner radius and 7° relief angle offers a compromise between sharpness and edge robustness. The moderate corner radius supports fine surface finishes without sacrificing resistance to edge breakdown, making the insert suitable for light to medium turning where both accuracy and tool life matter. The T3 plate thickness enhances rigidity in the cutting zone, reducing vibration and deflection—important factors for repeatable tolerances in batch production. Where this insert adds most value This insert is particularly effective for finishing and semi-finishing operations on unalloyed and alloyed Stahl, where consistent results and easy tool management are priorities. Its universal wear profile means fewer grade changes across mixed production, and the combination of coating and chip control helps maintain surface finish targets with lower supervision. For manufacturers aiming to streamline inserts across multiple lathes, the grade’s versatility contributes to simplified inventory and predictable machining outcomes. Discuss machining strategies with Metav Werkzeuge to select Walter Tools Tiger‑tec Gold inserts for improved productivity and process security — contact Metav Werkzeuge for tailored advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: DCMT11T304-MW4-WPP20G-WALTER SKU: DCMT11T304-MW4-WPP20G-WALTER Product: Turning insert Designation: DCMT11T304-MW4 WPP20G Manufacturer: Walter Tools Series: Tiger‑tec Gold Facts Size: 11 mm Thickness: T3 Free angle: 7° Corner radius: 0.4 mm Form: Rhombic 55° Tolerance class: M Special features Coating: Tiger‑tec Gold Grade: WPP20G (coated carbide) Chipbreaker: MW4 Material application: Stahl (ISO P) Suitability: Finishing to medium turning Plate designation: DCMT11T304-MW4 FAQ What materials is this insert suitable for? The DCMT11T304-MW4 WPP20G insert is designed for machining Stahl (ISO P) and performs well across a range of unalloyed and alloyed steels thanks to the Tiger‑tec Gold coating and the WPP20G grade. How does the MW4 chipbreaker affect machining? The MW4 chipbreaker on this Walter Tools insert improves chip control and evacuation, which helps maintain surface quality and reduces the risk of chip entanglement in turning operations. What benefits does the Tiger‑tec Gold coating provide? Tiger‑tec Gold offers a balanced wear resistance and toughness for coated carbide inserts, increasing edge life and process reliability when machining Stahl with the DCMT11T304-MW4 WPP20G. Which machining operations suit this insert best? This insert is optimised for finishing and light to medium turning tasks where a fine surface finish and consistent tool life are required. How does the geometry influence tool life? The Rhombic 55° angle, 0.4 mm corner radius and 7° relief angle deliver a robust cutting edge that resists chipping while allowing precision finishes, supporting repeatable performance on batch parts. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik‑Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT11T304-MW4 WSM20S WSM20S Wendeplatten - Walter Tools
Benefit from the combination of a wear-resistant Tiger·tec Silver grade and an optimised MW4 chipbreaker for reliable machining of difficult alloys; order directly via Metav Werkzeuge or contact our advisers for application support. DCMT11T304-MW4 WSM20S indexable turning insert — Tiger·tec Silver, MW4 chipbreaker (Walter Tools) The DCMT11T304-MW4 WSM20S is a rhombic 55° indexable turning insert engineered for secure cutting in stainless steel and high-temperature alloys, offering a fine 0.4 mm corner radius and a 7° relief angle for improved surface quality. Tiger·tec Silver coating for demanding materials Optimised MW4 chipbreaker for stable chips 0.4 mm corner radius for good edge life 7° relief angle for consistent cutting Consistent performance on difficult materials The combination of the WSM20S grade and Tiger·tec Silver coating targets stainless steel and heat‑resistant superalloys, delivering improved resistance to thermal and mechanical wear. The coated carbide chemistry is developed to maintain a stable cutting edge where adhesion and built-up edge would otherwise shorten tool life. This results in fewer interruptions, reduced regrinding and a more predictable production flow — a clear rational advantage for machining centres processing tough workpiece materials. Geometry that improves surface finish and chip control The rhombic 55° form with a 0.4 mm corner radius and 7° relief angle supports fine finishing cuts while preserving edge strength during tougher operations. The MW4 chipbreaker is shaped to produce controllable, medium-length chips in interrupted or continuous turning, reducing the risk of chip entanglement and improving process reliability. For operators less familiar with chipforming terminology, the chipbreaker is the engineered groove on the insert that controls chip shape and evacuation, directly influencing surface quality and machine uptime. Practical benefits for production and tool management Using a grade from the Tiger·tec Silver family brings measurable efficiency: improved edge stability lowers the frequency of insert changes and contributes to a consistent surface finish across batches. The insert’s designation and tolerance class support repeatable toolholding and easy re‑indexing in standard toolholders. For workshop planners, this means predictable cycle times and less variability in finished parts — a rational argument that supports investment in higher‑performance grades for challenging materials. Discuss machining trials and grade selection with Metav Werkzeuge to ensure optimal process security for stainless steel and superalloys — contact Metav Werkzeuge by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical data Article number: DCMT11T304-MW4-WSM20S-WALTER Designation: DCMT11T304-MW4 ISO designation: DCMT11T304-MW4 WSM20S Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WSM20S Chipbreaker: MW4 Plate form: Rhombus 55° Plate size: 11 Thickness: T3 Corner radius: 0,4 Relief angle: 7° Tolerance class: M Core data Size designation: 11 Corner radius: 0.4 mm Relief angle: 7° Thickness: T3 Tolerance class: M Special features Coating technology: Tiger·tec Silver Grade type: WSM20S (coated carbide) Chip control: MW4 chipbreaker Geometry: Rhombic 55° insert form Material groups: S / M Suitable for: stainless steel and high-temperature superalloys FAQ What materials can be machined with this insert? The DCMT11T304-MW4 WSM20S insert is designed for stainless steel and heat‑resistant superalloys (ISO groups M and S) thanks to the WSM20S grade and Tiger·tec Silver coating. How does the MW4 chipbreaker affect machining? The MW4 chipbreaker shapes medium‑length chips for reliable evacuation and consistent cutting forces, improving surface finish and reducing chip-related interruptions with this Walter Tools insert. Is the corner radius suitable for finishing operations? Yes, the 0.4 mm corner radius provides a balance between edge strength and fine surface quality, making the insert appropriate for finishing and semi‑finishing cuts. Which insert geometry suits interrupted cuts and general turning? The rhombic 55° form offers versatile cutting directions and good access in turning operations; combined with the 7° relief angle, it supports stable cutting in demanding workpiece materials. What does the WSM20S designation mean for tool life? WSM20S, as part of the Tiger·tec Silver family, is optimised for thermal stability and wear resistance, contributing to longer edge life and more predictable tool performance in difficult alloys. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original, factory‑new goods of the manufacturer.
DCMT11T304-RK4 WKK10S Wendeplatten - Walter Tools
Take advantage of the combination of reliable chip control and the wear-resistant WKK10S grade for efficient cast-iron turning; the robust RK4 chipbreaker and Tiger·tec Silver technology support stable production and predictable tool life. Order the insert via Metav Werkzeuge or consult our specialists for application advice. DCMT11T304-RK4 WKK10S indexable turning insert, Rhombus 55° for cast iron — Walter Tools A DCMT11T304-RK4 WKK10S indexable turning insert designed for productive machining of cast iron, combining a Rhombus 55° geometry with a chipbreaker optimised for brittle materials Tiger·tec Silver coated grade WKK10S RK4 chipbreaker for consistent chip control Rhombus 55° geometry for flexible turning 0.4 mm corner radius for fine surface finish Stable chip control for continuous production The RK4 chipbreaker is engineered for the short, brittle chips typical of cast iron, giving stable evacuation and reduced risk of edge damage. This leads to fewer interruptions and a steadier process window, which is a direct advantage in high-volume turning operations. The insert’s rhombus 55° geometry enables a range of approach angles, making the component suitable for both finishing and light to medium roughing where consistent chip formation and tool life are priorities. Coating and grade that prolong cutting edge life The combination of the WKK10S grade with Tiger·tec Silver coating provides a wear-resistant facing optimised for abrasive cast-iron workpieces. The grade is a coated carbide, tailored for abrasive wear resistance and reliable performance in interrupted cuts; this reduces flank wear and maintains dimensional accuracy over longer tool life. Explaining the technical advantage: the coating reduces friction and thermal load at the cutting zone, while the substrate provides toughness to withstand the frequent micro‑impacts that occur when machining grey and nodular cast iron. Geometry and dimensions that support precision and flexibility The insert’s 0.4 mm corner radius and 7° clearance balance surface quality and strength at the edge; the small radius improves finish while the clearance angle helps avoid rubbing on the workpiece. The 11 mm size and T3 thickness suit common toolholder systems accepting DCMT-style inserts, and the tolerance class M ensures repeatable seating in the pocket. Taken together, these parameters translate into a predictable cutting behaviour and simpler process setup, particularly when paired with toolholders and feeds optimised for cast-iron turning. Contact Metav Werkzeuge to discuss the Walter Tools DCMT11T304-RK4 WKK10S insert and its suitability for specific cast-iron applications — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: DCMT11T304-RK4-WKK10S-WALTER SKU / Label: Drehwendeschneidplatte DCMT11T304-RK4 WKK10S Walter Tools Manufacturer: Walter Tools Facts Corner radius: 0.4 mm Free angle: 7° Plate size: 11 mm Thickness: T3 Plate form: Rhombus 55° Tolerance class: M Special features Series: Tiger·tec Silver Grade: WKK10S Chipbreaker: RK4 Material applicability: Cast iron (K) Execution: T FAQ What materials is this insert intended for? The DCMT11T304-RK4 WKK10S insert is designed primarily for cast iron machining; the WKK10S grade and Tiger·tec Silver technology target the abrasive wear and short, breaking chips of cast-iron workpieces. How does the RK4 chipbreaker affect machining? The RK4 chipbreaker promotes stable chip formation and controlled evacuation, which reduces the risk of built-up edge and contributes to consistent surface quality when turning cast iron with the DCMT11T304-RK4 WKK10S insert. Is the geometry suitable for finishing operations? Yes — the Rhombus 55° shape combined with a 0.4 mm corner radius provides a good balance between edge strength and fine surface finish for finishing and light to medium roughing passes. Can the insert be used in interrupted cuts? The WKK10S coated carbide grade and robust substrate make the insert tolerant of interrupted cuts commonly encountered in cast-iron turning, offering improved resistance to micro‑impacts. Which toolholders are compatible with this insert? The DCMT-style seating fits standard toolholders for 55° rhombus inserts; using holders specified for DCMT11 sizes ensures proper clamping and repeatable positioning of the WKK10S insert. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation. There is no affiliation between our company and the named brands. The offered item is original, factory-new merchandise from Walter Tools.
DCMT11T304-RK4 WKK20S Wendeplatten - Walter Tools
The reinforced carbide grade and Tiger‑tec Silver coating combine for extended tool life and consistent performance in abrasive cast iron turning; the RK4 chipbreaker and Rhombus 55° geometry ensure controlled chip formation and versatile engagement. Order this high‑performance insert directly via Metav Werkzeuge or consult the team for application advice. DCMT11T304-RK4 WKK20S indexable turning insert for cast iron — Walter Tools, Tiger‑tec Silver, RK4 The DCMT11T304-RK4 WKK20S is a rhombic 55° indexable turning insert engineered for efficient machining of cast iron components in medium to heavy cutting conditions. Tiger‑tec Silver coating for enhanced wear resistance Optimised for cast iron machining Rhombic 55° geometry for versatile engagement RK4 chipbreaker for controlled chip formation Increase productivity in cast iron turning with targeted wear resistance The combination of a coated carbide substrate and the WKK20S grade from the Tiger‑tec Silver series delivers a balance between wear resistance and toughness that is particularly effective on abrasive cast iron. The result is a measurable reduction in flank wear growth over comparable grades, translating into fewer index changes and longer productive cycles. Emphasis on process efficiency and predictable tool life supports tighter planning and lower overall machining costs while maintaining consistent surface quality. Coating and grade explained for reliable performance The Tiger‑tec Silver technology denotes a multi‑layer coating system optimised for abrasive environments. In this case the selected grade was developed specifically for cast iron applications, where short, brittle chips and high abrasive wear dominate. The coated hardmetal construction improves thermal stability and edge retention under cyclic thermal loads. For engineers less familiar with coating terminology: the coating reduces abrasive wear and helps preserve the cutting edge, which means more consistent part tolerances across shifts. Geometry and edge design for controlled chip behaviour The Rhombus 55° insert form, combined with a 0.4 mm corner radius and a 7° clearance, provides a robust geometry that supports both interrupted cuts and continuous turning operations. The RK4 chipbreaker is tuned to produce short, manageable chips typical of cast iron, improving evacuation and reducing the risk of chip entanglement. The insert thickness designation T3 and tolerance class M indicate a stable seat in the toolholder and reproducible positioning for repeatable results in series production. Application scope and dependable machining results This insert is particularly suited to conventional and CNC lathe operations on cast iron components where consistent tool life and process reliability are required. The balance of abrasive resistance and sufficient toughness allows for both roughing passes and stable finishing when feed and speed are optimised. The Walter Tools development focus on stable edge life and good chip control contributes to fewer machine stops and a steady production flow, making the insert a practical choice for job shops and production environments alike. Discuss machining parameters and secure the DCMT11T304-RK4 WKK20S insert for your cast iron operations with Metav Werkzeuge — contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored recommendations and availability Technical data Article number: DCMT11T304-RK4-WKK20S-WALTER Product label: Drehwendeschneidplatte DCMT11T304-RK4 WKK20S Walter Tools Manufacturer: Walter Tools Product type: Drehwendeschneidplatte Grade / sort: WKK20S Series: Tiger‑tec Silver Facts Size designation: 11 Thickness: T3 Clearance angle: 7° Corner radius: 0.4 mm Tolerance class: M Special features Coating technology: Tiger‑tec Silver Chipbreaker: RK4 Geometry: Rhombus 55° Substrate: coated carbide (coated hardmetal) Application: cast iron machining FAQ What materials is this insert intended for? The DCMT11T304-RK4 WKK20S insert from Walter Tools is developed primarily for cast iron machining and is optimised for abrasive, short‑chip conditions common to those materials. Can the RK4 chipbreaker handle interrupted cuts? Yes, the RK4 chipbreaker is designed to produce short, controllable chips and performs well under interrupted cutting typical in cast iron operations with the DCMT11T304-RK4 WKK20S insert. How does the Tiger‑tec Silver coating improve tool life? The Tiger‑tec Silver multi‑layer coating reduces abrasive wear and improves thermal stability at the cutting edge, leading to longer usable life of the DCMT11T304-RK4 WKK20S insert under abrasive cast iron conditions. Which toolholder types are compatible with the DCMT11T304-RK4 insert? The insert follows a standard DCMT indexable turning geometry; compatible toolholders for DCMT‑type inserts should be used to ensure correct seat and clamping for reliable performance. What cutting edge radius and clearance should be considered for finishing passes? The insert features a 0.4 mm corner radius and 7° clearance; for finer surface finishes consider reduced feed or selecting a smaller radius in the same insert family where available. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Mention of brand names such as Walter Tools is for identification only; there is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of the mentioned manufacturer.
DCMT11T304-RM4 WMP20G RM4 Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, stable RM4 chip control and compact Rhombus geometry for reliable stainless steel turning and consistent component quality; order the inserts via Metav Werkzeuge or consult the specialists for application advice. DCMT11T304-RM4 WMP20G turning insert — Walter Tools, Tiger·tec Gold, for stainless steel The DCMT11T304-RM4 WMP20G is a coated carbide turning insert engineered for secure chip formation and reliable edge life when machining stainless steel under medium to robust conditions. DCMT11T304-RM4 WMP20G turning insert Tiger·tec Gold coated carbide grade Optimised RM4 chipbreaker for chips 7° clearance and 0.4 mm corner radius Consistent productivity when machining stainless steel The coated carbide grade WMP20G, based on Tiger·tec Gold technology, supports stable cutting edges and consistent chip formation when machining stainless steel. The composition and coating reduce the tendency to build up a cutting edge and to work-harden the material, which translates into fewer interruptions and more predictable tool life. As a result, process stability and component repeatability improve, contributing to a measurable rise in throughput and less frequent insert changes during production runs. Precision geometry that reduces cycle time and rework The insert geometry — a Rhombus 55° shape with 0.4 mm corner radius and 7° clearance — provides a balance between strength and accessibility for a wide range of turning tasks. The RM4 chipbreaker is optimised to break and evacuate chips effectively in the cutting zone, reducing the risk of surface damage and secondary operations. For workshops requiring dependable surface quality with minimal setup changes, this geometry offers enhanced tool life and reduced machine downtime through reliable chip control and stable cutting behaviour. Coating benefits and application advice for reliable results The Tiger·tec Gold coating on a fine-grain coated carbide substrate supports machining under medium to robust conditions and is particularly suited to the challenges of machining stainless steel, such as heat generation and material adherence. The coating improves thermal resistance and wear behaviour, helping to maintain a stable cutting edge during longer cycles. For selection and process parameters, consider the material group and cutting conditions; specialist guidance is available if the application falls between light finishing and heavier interrupted cuts. For specific machining data or compatibility checks, Metav Werkzeuge can provide technical support and recommendations. Contact Metav Werkzeuge for tailored advice on Walter Tools Tiger·tec Gold inserts and to ensure reproducible stainless steel machining results Technical data Article number: DCMT11T304-RM4-WMP20G-WALTER Designation: DCMT11T304-RM4 ISO designation: DCMT11T304-RM4 WMP20G Series: Tiger·tec Gold Grade: WMP20G Manufacturer: Walter Tools Facts Insert size: 11 Corner radius: 0.4 mm Clearance angle: 7° Thickness: T3 Special features Rhombus 55° shape RM4 chipbreaker Coated carbide grade (Tiger·tec Gold) Suited for stainless steel (M material group) Designed for medium to robust cutting conditions FAQ Which materials is this insert designed for? The DCMT11T304-RM4 WMP20G insert from Walter Tools is designed primarily for stainless steel (ISO material group M) and performs well under medium to robust machining conditions. What advantage does the RM4 chipbreaker provide? The RM4 chipbreaker promotes controlled chip formation and evacuation, reducing the risk of built-up edge and improving surface finish when turning tougher, ductile materials. What are the key geometry specifications of the insert? The insert features a Rhombus 55° shape, 0.4 mm corner radius and 7° clearance, with a thickness of T3 and an insert size of 11 for versatile turning applications. Is the grade coated and what does that mean for wear resistance? Yes — the WMP20G grade is a Tiger·tec Gold coated carbide, providing improved thermal resistance and wear performance for extended edge life in stainless steel turning. For which machining tasks does this insert excel? The insert is well suited to general turning where secure chip control and reliable edge life are required, especially in operations that face moderate to robust cutting demands rather than ultra-fine finishing. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision metalcutting tools and is part of the Swedish Sandvik group. Protected trademarks and product names are the property of their respective owners and are mentioned solely for explanatory purposes. There is no affiliation between our company and the named brands. The offered article is an original, factory-new product of the manufacturer.
DCMT11T304-RM4 WMP20S WMP20S Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Silver wear protection and the RM4 chipbreaker for sustained edge life and stable chip control; order directly via Metav Werkzeuge or request tailored cutting data from our consultants. DCMT11T304-RM4 WMP20S turning insert — Walter Tools, Tiger·tec Silver grade for rostfreier Stahl The DCMT11T304-RM4 WMP20S is a rhombic 55° indexable turning insert designed for reliable machining of rostfreier Stahl under medium to robust conditions Tiger·tec Silver coating for tough materials Optimised RM4 chipbreaker for secure chip control Rhombic 55° geometry for versatile turning 0.4 mm corner radius with 7° relief Improved process security and longer tool life The combination of the Tiger·tec Silver coating and the WMP20S carbide grade delivers noticeable increases in wear resistance and edge stability. The coating supports low friction and thermal resistance, which reduces wear mechanisms common in rostfreier Stahl machining. As a result, the insert maintains a consistent cutting edge for longer periods, which contributes to fewer tool changes and more predictable cycle times. This performance translates directly into improved process security and reduced downtime in series production. Predictable chip control for demanding stainless applications The RM4 chipbreaker is engineered to promote stable chip formation when machining tough, adhesive materials. In practice, the breaker geometry forces chips to curl and fragment reliably, lowering the risk of long, entangling swarf and improving surface quality. For operations where coolant strategy and evacuation are critical, the controlled chip flow reduces manual intervention and helps maintain consistent part finishes. This makes the insert particularly valuable for applications that demand repeatability and safe chip handling. Geometry tailored for versatile turning and surface quality The rhombic 55° shape provides a balanced approach between entry angle and cutting force, enabling versatile turning tasks from light finishing to medium roughing when combined with the 0.4 mm corner radius. The small radius increases edge strength without compromising surface finish, while the 7° relief angle supports secure cutting under variable depths of cut. Together these geometric choices deliver both dimensional accuracy and a fine surface quality on components made from rostfreier Stahl. Practical application and programming guidance Used as a series insert in shop-floor turning, the WMP20S grade suits machining strategies where moderate robustness and reliable chip control are priorities. The insert’s tolerance class M supports consistent seat fit and repeatable indexability in standard toolholders. For CAM programming, starting parameters can favour slightly reduced cutting speeds and increased feed per tooth compared with carbon steel to mitigate work-hardening; the coating and chipbreaker then enable steady material removal with predictable tool life. Contact Metav Werkzeuge today for cutting-data recommendations, batch pricing or application-specific advice on Walter Tools Tiger·tec Silver inserts — Metav Werkzeuge; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com Technical data SKU: DCMT11T304-RM4-WMP20S-WALTER Article designation: DCMT11T304-RM4 WMP20S Manufacturer: Walter Tools Product type: Turning insert Series: Tiger·tec Silver Grade: WMP20S Facts Free angle: 7° Corner radius: 0.4 mm Insert size: 11 Plate thickness: T3 Geometry: Rhombic 55° Chipbreaker: RM4 Tolerance class: M Special features Coated carbide grade Tiger·tec Silver Optimised chip control for rostfreier Stahl Suitable for medium to robust cutting conditions Indexable insert for standard turning toolholders FAQ What materials is this insert intended for? The DCMT11T304-RM4 WMP20S from Walter Tools is specifically engineered for machining rostfreier Stahl and performs best under medium to robust cutting conditions. How does the RM4 chipbreaker affect productivity? The RM4 chipbreaker on this Walter Tools insert promotes controlled chip formation, reducing swarf issues and supporting steadier cycle times in rostfreier Stahl turning operations. Can the insert be used for finishing operations? Yes, the rhombic 55° geometry combined with a 0.4 mm corner radius enables good surface finishes; the insert is suitable for light finishing when appropriate cutting parameters are applied. What does the Tiger·tec Silver series provide? Tiger·tec Silver enhances wear resistance and thermal stability for the WMP20S grade, extending edge life and improving process stability when machining rostfreier Stahl. Is this insert compatible with standard toolholders? The DCMT11T304-RM4 format and tolerance class M make the insert compatible with conventional turning toolholders designed for indexable plates. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is original, factory-new goods from the manufacturer.
DCMT11T304-RM4 WMP30G Tiger-tec Gold Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating and the RM4 chipbreaker for stable edge life and reliable chip control in stainless-steel turning; order the insert via Metav Werkzeuge or consult Metav Werkzeuge for application advice. DCMT11T304-RM4 WMP30G turning insert — rhombic 55° for stainless steels by Walter Tools The DCMT11T304-RM4 WMP30G is a rhombic 55° turning insert designed for robust and repeatable machining of stainless steels under medium to demanding conditions Tiger·tec Gold coating for stable edges Optimised RM4 chipbreaker for secure chips 7° clearance for controlled cutting 0.4 mm corner radius for robust performance Increase process reliability with a coating engineered for edge stability The combination of the WMP30G grade and Tiger·tec Gold coating promotes stable chip formation and improved resistance to thermal wear when machining stainless steels. This design reduces the risk of built-up edge and supports a predictable tool life, which in turn improves machine uptime and reduces unscheduled tool changes. The insert is made from coated carbide, formulated to handle the toughness and heat generation typical of these alloys, and is particularly suitable where consistent cutting performance is required. Achieve consistent part quality through geometry and edge preparation The rhombic 55° form and a 0.4 mm corner radius deliver a balance between strength and access for profile work. A 7° relief angle reduces rubbing at the flank and helps maintain surface finish while the geometry supports axial and radial clearances typical for general turning applications. Together these features contribute to reproducible surface integrity and dimensional stability, making the insert appropriate for serial production or small-batch work that demands repeatable results. Save time on setup and maintain steady productivity The insert's RM4 chipbreaker is optimised for chip control during moderate to robust cutting and assists in consistent evacuation when turning materials classified in the M group. Compatibility with standard toolholders is supported by the DCMT form factor, enabling straightforward integration into existing toolsets. The construction and coating focus on productivity: fewer tool changes, improved edge retention and a lower incidence of cutting interruptions — factors that directly support shop-floor efficiency. Practical recommendations for best results For turning operations in stainless steels, a steady feed and appropriate cooling strategy help exploit the WMP30G grade’s strengths: the coating resists thermal softening while the chipbreaker manages formation and flow. Where possible, ensure correct clamping and stable workholding to make the most of the insert’s edge security. When processing harder or highly adhesive stainless grades, review cutting conditions incrementally to identify the optimal balance between speed, feed and coolant to preserve tool life and part finish. For demanding stainless-steel turning, request genuine Walter Tools DCMT11T304-RM4 WMP30G inserts via Metav Werkzeuge for dependable edge life — contact Metav Werkzeuge for technical advice and availability Technical data Article number: DCMT11T304-RM4-WMP30G-WALTER Designation: DCMT11T304-RM4 WMP30G Manufacturer: Walter Tools Core data Corner radius: 0.4 mm Relief angle: 7° Plate size: 11 Plate thickness: T3 Special features Coating: Tiger·tec Gold Chipbreaker: RM4 Plate form: Rhombic 55° Material group: M (stainless steels) FAQ Is this insert suitable for austenitic stainless steels? The DCMT11T304-RM4 WMP30G is specified for the M material group and is suitable for austenitic and other stainless-steel variants where thermal resistance and stable chip control are required. What benefits does the Tiger·tec Gold coating provide? The Tiger·tec Gold coating on the WMP30G grade improves edge stability and wear resistance, supporting longer tool life and more consistent cutting behaviour in stainless-steel turning. Which chipbreaker is integrated and what is its effect? The insert uses the RM4 chipbreaker, which is optimised for secure chip formation and evacuation during moderate to robust cuts, reducing the risk of tangling and improving process reliability. Can the insert be used in existing DCMT toolholders? The DCMT form factor follows standard turning insert interfaces; the insert will fit holders designed for this geometry, enabling straightforward replacement and system compatibility. How does the 0.4 mm corner radius affect performance? The 0.4 mm radius increases edge robustness and resistance to chipping, supporting stable performance on turned profiles while balancing cutting forces and finish. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT11T304-RM4 WSM10S RM4 Wendeplatten - Walter Tools
Benefit from the combination of the Tiger·tec Silver coated grade and the RM4 chipbreaker for stable cutting in demanding alloys; the 7° clearance and 0.4 mm corner radius support consistent surface quality and tool life. Order the DCMT11T304-RM4 WSM10S indexable insert directly via Metav Werkzeuge or ask our consultants if needed. DCMT11T304-RM4 WSM10S turning insert — Tiger·tec Silver, RM4 chipbreaker (Walter Tools) The DCMT11T304-RM4 WSM10S is a rhombic 55° turning insert engineered for productive machining of stainless steels and heat‑resistant superalloys in demanding industrial turning applications. Tiger·tec Silver coated carbide grade WSM10S RM4 chipbreaker for stable chip control 7° clearance and 0.4 mm corner radius Rhombic 55° form, 11 mm inscribed circle Stable chip formation for uninterrupted production The RM4 chipbreaker is designed to promote predictable chip breaking and evacuation under varied cutting conditions. By controlling chip shape and flow, the geometry reduces the risk of built‑up edge and chuck interference, which translates into fewer interruptions and higher effective machining time. The result is measurable process stability when cutting tough, work‑hardening materials. Coating and grade tuned for high thermal and mechanical loads The combination of the Tiger·tec Silver coating with the WSM10S substrate provides a balance of heat resistance and edge stability for the machining of stainless steels (ISO group M) and high‑temperature alloys (ISO group S). The coated cemented carbide composition supports prolonged flank wear resistance and consistent cutting edge performance, helping to maintain dimensional accuracy across longer tool life cycles. Geometry engineered for precision and surface finish The rhombic 55° form and the 11 mm inscribed circle create a versatile seating and cutting orientation, while the 7° clearance angle reduces rubbing at the flank. The 0.4 mm corner radius gives a reliable edge for semi‑finishing and finishing passes where surface quality matters. The overall insert thickness T3 contributes to robust support in the pocket, improving repeatability and resistance to mechanical shock. Application guidance and integration into production This indexable insert is well suited to both serial production and small‑batch runs where a consistent edge and chip control are required. The grade and chipbreaker combination facilitates machining strategies that favour controlled feed and moderate cutting speeds when processing stainless steels or nickel‑based alloys, minimising rework and improving first‑pass yield. For further machining data, cutting parameters and compatible toolholders, technical enquiries can be directed to Metav Werkzeuge for tailored recommendations. Contact Metav Werkzeuge today to discuss how the Walter Tools DCMT11T304-RM4 WSM10S can be integrated into existing tool systems and to request cutting data for specific materials Technical data Article number: DCMT11T304-RM4-WSM10S-WALTER Product type: turning insert Designation: DCMT11T304-RM4 WSM10S Manufacturer: Walter Tools Series: Tiger·tec Silver Core specifications Inscribed circle: 11 mm Clearance angle: 7° Corner radius: 0.4 mm Thickness: T3 Insert form: Rhombic 55° Tolerance class: M Special features Coating: Tiger·tec Silver Grade: WSM10S (coated cemented carbide) Chipbreaker: RM4 Material applicability: stainless steels (M), heat‑resistant alloys / titanium (S) Intended use: turning, semi‑finishing and finishing operations FAQ What materials is this insert intended for? The DCMT11T304-RM4 WSM10S insert is designed for stainless steels (ISO group M) and heat‑resistant superalloys or titanium (ISO group S), leveraging the Tiger·tec Silver coating and WSM10S grade for thermal and edge stability. How does the RM4 chipbreaker affect machining? The RM4 chipbreaker on this Walter Tools insert promotes controlled chip formation and evacuation, reducing built‑up edge and improving process stability during turning operations. Which cutting geometries benefit most from this insert? Applications that require a balance between surface finish and tool life benefit from the 0.4 mm corner radius and 7° clearance; the Rhombic 55° form allows multi‑orientational use in a wide range of clamping pockets. Is this insert suitable for finishing passes? Yes, the combination of coating, grade and geometry makes the insert suitable for semi‑finishing and finishing, where consistent surface quality and edge integrity are required. What should be considered for toolholder selection? Choose a toolholder that matches the Rhombic 55° seat and provides secure support for a T3‑thick insert; correct clamping and stable setup are key to benefitting from the WSM10S performance. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DCMT11T304-RM4 WSM20S RM4 Wendeplatten - Walter Tools
Take advantage of a high-performance Tiger·tec Silver grade and a dedicated RM4 chipbreaker to achieve stable chip control and extended tool life when machining demanding materials; order the insert directly via Metav Werkzeuge or consult our specialists for cutting-parameter recommendations. DCMT11T304-RM4 WSM20S indexable turning insert – Rhombic 55° for rostfreiem Stahl & superalloys | Walter Tools The DCMT11T304-RM4 WSM20S is a 55° rhombic indexable turning insert engineered for heavy-duty machining of rostfreiem Stahl and heat-resistant superalloys in demanding turning operations Tiger·tec Silver coated carbide grade WSM20S RM4 chipbreaker for controlled chip formation Rhombic 55° profile with 0.4 mm corner radius 7° relief angle for stable cutting performance High-performance grade for demanding alloys and rostfreiem Stahl The combination of the WSM20S grade and the Tiger·tec Silver technology provides a coating system and substrate pairing specifically tuned for temperature resistance and edge strength. This results in improved resistance to built-up edge and thermal degradation when machining rostfreiem Stahl and nickel-based alloys. For production environments that prioritise consistent surface finish and predictable tool life, the coated carbide composition enables higher cutting speeds and fewer tool changes, translating into measurable productivity gains and lower machining costs per part. Geometry that stabilises the cutting process and improves repeatability Designed with a Rhombic 55° form and a 0.4 mm corner radius, the insert provides a balance between edge strength and accessibility for common turning profiles. The 7° relief angle reduces friction on the flank face and helps maintain a steady cutting force, while the RM4 chipbreaker promotes short, controlled chips under a wide range of feeds. Together, these geometry choices reduce vibration and improve dimensional repeatability, making the insert suitable for both uninterrupted and slightly interrupted cutting conditions where process stability is essential. Productivity and tool life benefits from tailored chip control The dedicated RM4 chip control geometry is optimised to evacuate swarf efficiently and to preserve the integrity of the cutting edge during transient thermal loads. In practice, this means longer intervals between indexing and a lower risk of machine downtime caused by chip-related issues. The result is a clear cost-benefit in medium- to high-volume turning, where the coated substrate of the insert combines thermal protection with robust wear behaviour to support consistent part quality over extended cycles. Practical compatibility and recommended use cases The insert suits turning applications where rostfreiem Stahl and heat-resistant superalloys (ISO groups M and S) are predominant. Typical uses include component finishing and semi-finishing on turned shafts, fittings and parts with tight surface requirements. The insert is manufactured in the T3 thickness variant and fits holders that accept the DCMT 11-size geometry; pairing with appropriate toolholders and adjusted cutting data will ensure optimum results. For tailored recommendations on feeds and speeds for specific materials, Metav Werkzeuge can provide application advice and parameter tables. Contact Metav Werkzeuge today for tailored cutting data and application support for Walter Tools' Tiger·tec Silver inserts, or request a recommendation for the DCMT11T304-RM4 WSM20S to optimise your turning process Technical data Article number: DCMT11T304-RM4-WSM20S-WALTER Label: Drehwendeschneidplatte DCMT11T304-RM4 WSM20S Walter Tools Manufacturer: Walter Tools Facts Shape: Rhombus 55° Corner radius: 0.4 mm Relief angle: 7° Plate size: 11 mm Thickness: T3 Tolerance class: M Special features Series: Tiger·tec Silver Grade: WSM20S (coated carbide) Chipbreaker: RM4 Material suitability: S / M (superalloys / rostfreiem Stahl) Execution: T FAQ What materials is this insert suitable for? The DCMT11T304-RM4 WSM20S insert is intended primarily for rostfreiem Stahl and heat-resistant superalloys, corresponding to ISO groups M and S. What chip control does the insert provide? The RM4 chipbreaker on the Walter Tools insert promotes reliable, short chips and consistent evacuation to support uninterrupted machining. What are the key geometric specifications? The insert features a Rhombic 55° form, a 0.4 mm corner radius and a 7° relief angle to combine edge strength with stable cutting. Which series and coating are used on this insert? The insert belongs to the Tiger·tec Silver series with the WSM20S coated-carbide grade, optimised for thermal resistance and edge stability. Which holder size is compatible with this insert? The DCMT11T304-RM4 geometry corresponds to standard DCMT 11-size turning holders used in conventional indexable turning tool systems. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Walter Tools (Walter AG) is a leading manufacturer of precision tooling for metalworking and operates under the brand Walter Tools; the company delivers advanced solutions for demanding machining tasks and is part of a wider industrial group. Marked brand names and trademarks are the property of their respective owners. The mentioned brand is cited for clarification; there is no affiliation implied between our company and the listed manufacturers.
DCMT11T304-RM4 WSM30S RM4 Wendeplatten - Walter Tools
Take advantage of the proven combination of Tiger·tec Silver technology and an optimised RM4 chipbreaker for stable cutting of stainless steels and heat-resistant alloys; order through Metav Werkzeuge or request detailed application advice from our consultants. DCMT11T304-RM4 WSM30S – indexable turning insert with Tiger·tec Silver for stainless steels and superalloys (Walter Tools) The DCMT11T304-RM4 WSM30S is an indexable turning insert designed for heavy-duty and difficult-to-machine materials, offering consistent edge stability and predictable chip control for industrial turning applications Tiger·tec Silver coating for heat resistance Optimised RM4 chipbreaker for stable chips Rhombus 55° with 0.4 mm corner radius Designed for stainless steels and superalloys High-performance grade for demanding alloys The combination of the Tiger·tec Silver coating with the WSM30S grade provides a coated carbide system tailored to maintain cutting-edge integrity when machining tough materials. Because the substrate and multilayer coating are engineered for heat resistance and wear control, the insert supports secure chip formation and reduced edge build-up when working with stainless steels and superalloys. This results in longer productive tool life and fewer unplanned stoppages, translating directly into higher machine utilisation and predictable processing times. Geometry that stabilises cutting and improves surface finish The rhombus 55° shape and the 0.4 mm corner radius offer a robust cutting edge that balances strength and finish quality. The 7° clearance reduces rubbing on the flank while the RM4 chipbreaker optimises chip flow for a wide range of feed rates. The T3 thickness adds body to the insert for stable seating and repeatable performance in standard turning toolholders. Together these features reduce vibration and produce consistent surface integrity, especially in interrupted cuts or tougher workpiece conditions. Productivity gains and industrial reliability Designed under the Walter Tools quality standard, this insert supports efficient machining strategies for industrial environments. The RM4 chipbreaker contributes to predictable chip control that eases swarf handling and supports higher cutting parameters where appropriate. Combined with the Tiger·tec Silver technology, the insert reduces the need for frequent edge changes and contributes to lower tool-change downtime. The net effect is enhanced throughput and reliable part quality in batch production and continuous operations. Contact Metav Werkzeuge for tailored application guidance on the Walter Tools DCMT11T304-RM4 WSM30S, including recommended cutting parameters and holder compatibility via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: DCMT11T304-RM4-WSM30S-WALTER Item: Drehwendeschneidplatte DCMT11T304-RM4 WSM30S Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WSM30S Facts Free angle: 7° Corner radius: 0.4 Plate size: 11 Plate thickness: T3 Tolerance class: M Special features Geometry: Rhombus 55° Chipbreaker: RM4 Material suitability: S / M Coating/technology: Tiger·tec Silver Application: stainless steels, superalloys FAQ Which materials is this insert suitable for? The DCMT11T304-RM4 WSM30S is intended for stainless steels (M) and heat-resistant superalloys (S), reflecting its design focus on heat resistance and edge stability. What does the RM4 chipbreaker deliver in practice? The RM4 chipbreaker on the DCMT11T304-RM4 WSM30S controls chip form and evacuation, improving swarf management and enabling more consistent cutting forces during turning. Can this insert be used in standard toolholders for DCMT formats? Yes, the DCMT11T304-RM4 format is compatible with conventional toolholders designed for DCMT geometry; correct clamping and seat integrity are essential for repeatable performance. How does the Tiger·tec Silver technology affect tool life? Tiger·tec Silver coating increases thermal and abrasive resistance, which helps extend edge life under demanding conditions and reduces the frequency of index changes. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only; there is no affiliation between our company and the named brands. The offered article is an original, factory-new product of the manufacturer.
DCMT11T304-RP4 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of high process stability, durable Tiger·tec Gold coating and reliable chip control for efficient turning operations. The insert delivers consistent performance when machining steel and reduces downtime through predictable wear behaviour. Order directly via Metav Werkzeuge or request technical advice from the consultants for application-specific recommendations. DCMT11T304-RP4 WPP10G — Turning insert, RP4 chipbreaker, 0.4 mm corner radius (Walter Tools) The DCMT11T304-RP4 WPP10G is a rhombic 55° turning insert designed for steel machining, featuring the Tiger·tec Gold coated-carbide grade and an RP4 chipbreaker for controlled chip formation. Tiger·tec Gold coating for extended tool life Optimised for steel cutting (ISO group P) Rhombic 55° form with 0.4 mm corner radius RP4 chipbreaker for controlled chip formation Efficient cutting performance for steel components The insert combines the Tiger·tec Gold coating with the WPP10G grade to provide a balance of toughness and wear resistance suited to the thermal and mechanical demands of steel turning. As a coated carbide solution, the geometry and substrate are matched to deliver high productivity in serial production and single-part machining alike. The design reduces the frequency of tool changes and supports steady machining parameters, enabling reliable cycle times and improved part throughput. Predictable chip formation and improved surface quality The RP4 chipbreaker works in concert with the rhombic 55° form and a 0.4 mm corner radius to produce short, controllable chips when machining steels, which lowers the risk of chip entanglement and improves process safety. The combination of chip control and insert geometry also contributes to better surface integrity and repeatable finishing results, especially on medium to heavy interrupted cuts. Operators and process planners benefit from reduced rework and more consistent part quality. Robust process stability and longer tool life Built to tolerance class M, the insert maintains geometric consistency across batches, supporting predictable tool life and easy indexability. The coated grade resists flank and crater wear typical in steel applications, which translates into longer intervals between indexings and less unplanned downtime. The result is a measurable reduction in tooling cost per component and a smoother production flow for turning operations where stability and repeatability are priorities. Application scope and compatibility with ISO material groups According to the specification, the cutting grade is tailored for the ISO group P, which denotes suitability for unalloyed and alloyed steels. The insert’s construction and chipbreaker make it appropriate for a wide range of steel machining tasks, from finishing to more robust turning operations. When specific process conditions or unusual materials are involved, process engineers should match feed, speed and depth settings to machine capability and workpiece demands to optimise tool performance. Contact Metav Werkzeuge for tailored cutting data and application advice on Walter Tools Tiger·tec Gold inserts like the DCMT11T304-RP4 WPP10G Technical Data Article number: DCMT11T304-RP4-WPP10G-WALTER Description: DCMT11T304-RP4 WPP10G Manufacturer: Walter Tools Product type: Turning insert (drehwendeschneidplatte) Grade: WPP10G Series: Tiger·tec Gold Core specifications Insert size: 11 Plate thickness: T3 Corner radius: 0.4 mm Clearance angle: 7° Plate form: Rhombic 55° Tolerance class: M Special features Chipbreaker: RP4 Coating / grade: WPP10G (coated carbide, Tiger·tec Gold) Material suitability: Steel (ISO group P) Execution: T FAQ Which materials is this insert suitable for? The DCMT11T304-RP4 WPP10G turning insert (Walter Tools) is specified for ISO group P, indicating suitability for unalloyed and alloyed steels. What is the corner radius and how does it affect machining? The insert has a 0.4 mm corner radius; this radius increases edge strength compared with finer radii and supports a balance between surface finish and robustness in turning operations. What advantages does the Tiger·tec Gold WPP10G grade provide? The WPP10G grade combines a Tiger·tec Gold coating with a coated-carbide substrate to offer a compromise of wear resistance and toughness tailored for steel machining, promoting longer tool life under typical turning conditions. What does the RP4 chipbreaker deliver in practice? The RP4 chipbreaker is designed to ensure short, controllable chips when cutting steel, improving process safety and reducing the likelihood of chip-related interruptions. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for clarification only. There is no connection between our company and the mentioned brands. The offered item is original, brand-new goods from the manufacturer Walter Tools.
DCMT11T304-RP4 WPP20G T Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Gold coating, a dedicated WPP20G grade for steel and a proven RP4 chipbreaker to ensure reliable machining, long tool life and consistent surface quality; order directly via Metav Werkzeuge or consult the technical team for cutting data and application support. DCMT11T304-RP4 WPP20G indexable turning insert — Tiger·tec Gold, Walter Tools (RP4, 7°) The DCMT11T304-RP4 WPP20G is a rhombic 55° indexable turning insert designed for general steel turning, combining a wear-resistant coating with an RP4 chipbreaker for stable chip formation and reproducible results. Tiger·tec Gold coating for high process security Optimised RP4 chipbreaker for consistent chips Rhombic 55° geometry for versatile turning 0.4 mm corner radius for precise finishing Reliable performance for steel turning with reduced tool changes The combination of Tiger·tec Gold coating and the WPP20G carbide grade is engineered for machining steels in accordance with ISO P, offering an improved balance between wear resistance and toughness. The coating reduces flank wear and enhances thermal resistance, which means fewer tool changes and more predictable life in serial production. In practice, this results in a more stable process window and consistent part quality when turning unalloyed and alloyed steel grades. The insert's substrate and coating technology are aimed at achieving a high level of process reliability and repeatable performance. Geometry and chip control that improve finish and cycle time The Rhombic 55° insert geometry together with the RP4 chipbreaker and a 0.4 mm corner radius delivers controlled chip formation and good surface finish on offhand and continuous turns. A 7° clearance angle helps to reduce rubbing and heat accumulation while the RP4 groove actively breaks chips across a range of feeds, lowering the risk of built-up edge and workpiece damage. These features combine to shorten cycle times and reduce secondary operations, contributing directly to production efficiency and fewer rejects. Compact design for adaptable clamping and secure productivity With a plate size of 11 and thickness T3, the insert fits common turning toolholders and provides a stable cutting edge for a wide range of routine turning tasks. The compact profile and robust cutting edge reduce vibrations and improve dimensional consistency, which is especially valuable in batch runs and mixed-production environments. The coating and grade pairing supports higher cutting parameters where machine rigidity and cooling permit, enabling more economical metal removal rates without compromising component integrity. Clear application scope and practical recommendations This insert is specified for steel machining per the ISO grouping and is optimised for the thermal and chip-formation characteristics typical of these materials. The RP4 chipbreaker is suitable for general turning including medium-depth cuts and finishing passes; for heavy interrupted cuts or specialised alloys, select a dedicated geometry or grade. For precise clamping advice, recommended feeds and speeds or when integrating the insert into a tool assembly, Metav Werkzeuge offers technical documentation and consultation to adapt parameters to the machine, holder and workpiece. For machining with Walter Tools' Tiger·tec Gold technology and the WPP20G grade, contact Metav Werkzeuge for cutting data, sample quantities or application advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: DCMT11T304-RP4-WPP20G-WALTER Article: Drehwendeschneidplatte DCMT11T304-RP4 WPP20G Walter Tools Manufacturer: Walter Tools Series: Tiger-tec Gold Grade: WPP20G Substrate: coated carbide Facts Clearance angle: 7° Corner radius: 0.4 mm Plate size: 11 Thickness: T3 Tolerance class: M Special features Geometry: Rhombus 55° Chipbreaker: RP4 Material application: steel (ISO P) Execution: T ISO designation: DCMT11T304-RP4 WPP20G FAQ What materials is this insert intended for? This insert is designed primarily for machining steel; the WPP20G grade and Tiger·tec Gold coating are optimised for ISO P applications. How does the RP4 chipbreaker affect machining? The RP4 chipbreaker controls chip formation across a range of feeds to promote stable chips and improve surface finish during turning operations. Can this insert be used for stainless steel or hardened materials? The supplied data indicates optimisation for steel (ISO P); for stainless or hardened applications, select a grade and geometry specified for those material groups. What are the main benefits of the Tiger·tec Gold series? Tiger·tec Gold provides enhanced wear resistance and thermal stability, which helps extend tool life and stabilise production processes in steel machining. Is the insert compatible with standard DCMT toolholders? The insert uses the DCMT geometry and standard clamping conventions; confirm holder shoulder and clamping parameters to ensure correct seating and rigidity. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only; there is no affiliation between our company and the mentioned brands. The offered item is original, brand-new goods from the manufacturer.
DCMT11T304-RP4 WPP30G WPP30G Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Gold coating and an RP4 chipbreaker for stable cutting performance in steel machining; the insert’s 7° clearance and 0.4 mm corner radius support consistent edge life and reliable surface quality. Order directly via Metav Werkzeuge or contact their consultants for specific cutting data and stock information. DCMT11T304-RP4 WPP30G turning insert — Tiger‑tec Gold, RP4 chipbreaker (Walter Tools) A DCMT11T304-RP4 WPP30G turning insert engineered for steel turning, combining a Tiger‑tec Gold coating with an RP4 chipbreaker for controlled chips and predictable tool life. Tiger‑tec Gold coating for longer tool life RP4 chipbreaker for reliable chip control 7° clearance for smooth cutting action 0.4 mm corner radius for robust edge strength Higher process security through advanced coating and grade The combination of Tiger‑tec Gold and the WPP30G grade gives a clear advantage where repeatable performance and wear resistance matter. The coated carbide composition is optimised for the thermal and mechanical conditions encountered when machining steel, so flank wear is reduced and tool changes become less frequent. This leads to a measurable increase in productivity and lower total tooling cost per component when compared to uncoated grades. The series’ balanced hardness and toughness ensure that tool life is not gained at the expense of reliability. Consistent chip control and improved surface finish The RP4 chipbreaker is designed to produce short, controllable chips in a wide range of cutting regimes, which simplifies chip evacuation and reduces the risk of tangling in automated turning centres. Combined with the Rhombus 55° geometry, the insert provides a positive cutting edge that supports stable engagement and good access to narrow grooves or stepped features. The 7° clearance angle reduces rubbing on the flank, while the 0.4 mm corner radius balances edge strength with the ability to achieve fine surface finishes on shaft and journal features. Practical benefits on the shop floor and application guidance With a nominal size of 11 and a plate thickness of T3, the insert is suitable for a variety of external turning operations where stiffness and repeatability are required. The tolerance class M supports consistent seating in toolholders, which is essential for automated setups. The grade’s designation confirms suitability for steel applications according to ISO group P, making selection straightforward for production planners. Where higher feed rates or interrupted cuts are encountered, the robust corner radius and coated surface help to maintain cutting-edge integrity and reduce downtime for regrinds or replacements. Contact Metav Werkzeuge for tailored cutting parameters, availability and expert advice on integrating Walter Tools Tiger‑tec Gold inserts into existing turning processes Technical data Article number: DCMT11T304-RP4-WPP30G-WALTER Label: Drehwendeschneidplatte DCMT11T304-RP4 WPP30G Walter Tools Manufacturer: Walter Tools Facts Clearance angle: 7° Corner radius: 0.4 mm Insert size: 11 mm Thickness: T3 Tolerance class: M Shape: Rhombus 55° Special features Series: Tiger‑tec Gold Grade: WPP30G (coated carbide) Chipbreaker: RP4 ISO designation: DCMT11T304-RP4 WPP30G Base designation: DCMT11T304-RP4 Execution: T Material application: Steel (P) FAQ What materials is this insert intended for? The DCMT11T304‑RP4 WPP30G insert is specified for machining steel (ISO group P) and its coating and grade are optimised for the typical heat and chip formation of steel turning. How does the RP4 chipbreaker affect process stability? The RP4 chipbreaker produces short, controllable chips that simplify evacuation and reduce the risk of chip entanglement, which enhances stability in continuous and automated turning. What are the advantages of the Tiger‑tec Gold coating? The Tiger‑tec Gold coating improves wear resistance and thermal stability, which extends tool life and helps maintain consistent surface quality over longer production runs. Is the insert suitable for interrupted cuts or higher feeds? Yes, the 0.4 mm corner radius and coated grade provide a robust edge suitable for interrupted cuts and increased feed situations, offering reliable performance under demanding conditions. Hersteller: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT11T308-FK6 WKK10S Wendeplatten - Walter Tools
Combining the WKK10S coated grade with the FK6 chipbreaker and a 0.8 mm corner radius, this insert offers robust wear resistance and controlled chip formation for cast iron turning. Order the DCMT11T308-FK6 WKK10S directly via Metav Werkzeuge or contact the consultants for tailored application advice. DCMT11T308-FK6 WKK10S indexable turning insert, Tiger·tec Silver coating — Walter Tools The DCMT11T308-FK6 WKK10S is a rhombic 55° indexable turning insert optimised for machining cast iron with a FK6 chipbreaker for stable and predictable chip control Tiger·tec Silver coating for extended tool life Optimised for cast iron machining (ISO group K) Rhombic 55° form with 0.8 mm corner radius FK6 chipbreaker for controlled chip formation Higher productivity on abrasive cast iron The coated carbide grade WKK10S in the Tiger·tec Silver series is formulated for abrasive cast iron applications, delivering consistent wear resistance and a longer service interval compared with uncoated grades. Because the grade balances hardness and fracture toughness, the cutting edge resists the fast, abrasive wear common when machining grey and nodular cast irons. This results in fewer insert changes and more stable cycle times on batch production runs. The combination of the coated substrate and a chipbreaker designed for cast materials provides reliable chip control that reduces interruptions from built-up edge and broken chips. Predictable surface finish and dimensional control The rhombic 55° geometry with a 0.8 mm corner radius and a 7° relief angle creates a versatile cutting profile that supports turning and light finishing passes without compromising strength. The FK6 chipbreaker promotes short, controllable chips which help maintain tool stability and protect the workpiece surface, improving repeatability across parts. Tolerance class M and the standardised insert form make mounting and index changes straightforward, supporting consistent part quality and minimising setup variation in serial production. Easy integration and reliable process security This indexable insert is supplied in the established DCMT configuration and fits common toolholders used in turning operations, allowing quick adoption into existing setups. The coated grade and chip control characteristics reduce the need for excessive cutting-fluid adjustments, supporting efficient wet or semi-dry processes. With applicability to ISO group K (cast iron) and a compact plate thickness T3, the insert supports compact clamping arrangements and predictable tool life, helping to lower overall machining costs and downtime. For additional cutting data or to confirm suitability for a particular cast iron grade, Metav Werkzeuge provides application support and technical consulting. Contact Metav Werkzeuge today to discuss integration of the Walter Tools DCMT11T308-FK6 WKK10S into production or request personalised cutting data and application recommendations Technical Data Article number: DCMT11T308-FK6-WKK10S-WALTER Designation: DCMT11T308-FK6 WKK10S Product type: Drehwendeschneidplatte / indexable turning insert Manufacturer: Walter Tools Series: Tiger·tec Silver Facts Corner radius: 0.8 mm Relief (free) angle: 7° Insert form: Rhombic 55° Plate size: 11 Thickness: T3 Tolerance class: M Special features Grade: WKK10S (coated carbide) Coating: Tiger·tec Silver Chipbreaker: FK6 Suitable material group: cast iron (ISO K) Application focus: abrasive wear resistance and short, breaking chips FAQ What materials is this insert designed for? The DCMT11T308-FK6 WKK10S insert (Walter Tools) is specifically designed for machining cast iron and is classified for ISO group K applications. How does the FK6 chipbreaker affect chip formation? The FK6 chipbreaker on the DCMT11T308-FK6 WKK10S produces short, controllable chips that reduce entanglement and improve surface integrity during cast iron turning. What are the key geometry parameters to consider for finishing passes? Consider the rhombic 55° form and the 0.8 mm corner radius for light finishing; these geometries balance cutting edge strength with the ability to achieve good surface finishes. Is the coating beneficial for productivity? Yes, the Tiger·tec Silver coating on the WKK10S grade enhances wear resistance and contributes to longer tool life and more consistent cycle times in abrasive cast iron operations. Will this insert fit standard DCMT toolholders? The insert follows the DCMT configuration and is compatible with holders designed for that form; confirm holder compatibility with the toolholder manufacturer and the DCMT11T308-FK6 specification. Manufacturer / Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and brand names are the property of their respective owners. Brand names and protected designations are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The offered item is original, factory-new merchandise of the manufacturer.
DCMT11T308-FK6 WKK20S Wendeplatten - Walter Tools
Take advantage of the combination of reliable chip control, a Tiger‑tec Silver coating and a robust geometry for consistent cast‑iron turning performance; order the insert through Metav Werkzeuge or consult their specialists for application advice. DCMT11T308-FK6 WKK20S indexable turning insert – FK6 chipbreaker, Tiger‑tec Silver, for cast iron (Walter Tools) The DCMT11T308-FK6 WKK20S is an indexable turning insert designed for machining cast iron, combining a chip‑controlling FK6 breaker with a wear‑resistant Tiger‑tec Silver coating for stable production. Tiger‑tec Silver coated grade WKK20S Optimised for cast‑iron machining FK6 chipbreaker for controlled chips Rhombic 55° with 0.8 mm corner radius Consistent metal removal and predictable tool life for cast‑iron work The grade WKK20S is specifically matched to the demands of cast iron machining: it is a coated carbide designed to handle abrasive wear and the short, breaking chips typical of these materials. The FK6 chipbreaker promotes controlled chip formation, reducing the risk of built‑up edge and machine interruptions. For production environments this results in more predictable tool life, fewer unscheduled stops and a steadier output quality when turning grey or nodular castings. Durable cutting edge and process security thanks to advanced coating Equipped with Tiger‑tec Silver technology, the insert offers a coating system that enhances thermal resistance and abrasion protection compared with uncoated grades, delivering process reliability across extended runs. The combination of coated carbide and the specified tolerance class M ensures reproducible seating and repeatable cutting performance in indexable tooling systems, which supports stable cycle times and simplified tool management on the shop floor. Geometry that balances edge strength and surface finish The rhombic 55° form together with a 0.8 mm corner radius and a 7° relief angle creates an insert geometry that balances robustness and finishing capability. The moderate radius increases edge strength for interrupted cuts, while the 55° orientation provides good access on facing and light turning operations. The insert thickness T3 adds mechanical rigidity to withstand typical turning forces in cast‑iron applications, helping to reduce vibration and improve surface consistency on the workpiece. Contact Metav Werkzeuge for tailored application recommendations and to secure Walter Tools inserts from the Tiger‑tec Silver range for reliable cast‑iron machining. Technical data SKU: DCMT11T308-FK6-WKK20S-WALTER Article designation: DCMT11T308-FK6 WKK20S Manufacturer: Walter Tools Core data Relief angle: 7° Corner radius: 0.8 mm Insert size: 11 Thickness: T3 Tolerance class: M Special features Series: Tiger‑tec Silver Grade: WKK20S (coated carbide) Chipbreaker: FK6 Plate form: Rhombus 55° Material application: cast iron FAQ What materials is this insert suitable for? The DCMT11T308-FK6 WKK20S from Walter Tools is formulated primarily for cast iron applications and is optimised for the abrasive and chipping characteristics of those materials. How does the FK6 chipbreaker benefit production? The FK6 chipbreaker on the WKK20S insert promotes safe, short chip formation and easier evacuation, which helps maintain process stability and reduces interruptions during cast‑iron turning. What advantages does Tiger‑tec Silver provide? The Tiger‑tec Silver coating increases wear resistance and thermal stability of the coated carbide, supporting longer tool life and consistent cutting performance under typical turning conditions. Is the insert suitable for interrupted cuts or heavy machining? The combination of a 0.8 mm corner radius, T3 thickness and rhombic 55° geometry provides enhanced edge strength that is beneficial for interrupted cuts and routine turning tasks in cast‑iron components. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DCMT11T308-FM4 WMP20G FM4 Wendeplatten - Walter Tools
Take advantage of Tiger·tec Gold surface technology and the FM4 chipbreaker to secure stable chip formation and consistent performance when machining rostfreien Stahl; order or request advice directly via Metav Werkzeuge for seamless integration into existing turning tools. DCMT11T308-FM20G WMP20G turning insert for rostfreien Stahl by Walter Tools — Tiger·tec Gold, FM4 chipbreaker A DCMT11T308-FM4 WMP20G indexable turning insert engineered for reliable machining of rostfreien Stahl under medium to robust conditions, combining a coated carbide grade with a positive geometry for predictable cutting behaviour Tiger·tec Gold coating for extended tool life Optimised FM4 chipbreaker for secure chip control Rhombic 55° shape with 0.8 mm corner radius 7° clearance angle for reliable cutting performance Consistent machining of rostfreien Stahl for fewer interruptions The Tiger·tec Gold coating in this grade promotes stable chip formation and a durable cutting edge when working with rostfreien Stahl, materials that tend to be tough and generate heat. The WMP20G grade is a coated cemented carbide class developed to reduce built-up edge and maintain edge integrity under medium to robust cutting conditions. These technical choices result in fewer tool changes and more predictable cycle times, improving process reliability on turning operations. Geometry that improves surface finish and cutting forces The rhombic 55° profile together with a 0.8 mm corner radius and an effective FM4 chipbreaker produce controllable chip flow and a balanced contact area, which supports improved surface quality with moderate cutting parameters. A 7° clearance angle reduces rubbing and heat generation at the flank, lowering the risk of premature wear. This geometry is particularly helpful when a combination of edge strength and lower cutting resistance is required for consistent part quality. Easy integration into standard toolholders to reduce downtime The insert follows the common ISO-style designation and the T3 plate thickness, which simplifies replacement and stock management across workshops. The positive-form geometry and robust grade mean fewer unexpected interruptions, while the FM4 breaker keeps chips compact for safer operation and easier disposal. Technical advisers are available to explain compatibility with existing toolholders and to recommend optimal cutting data for specific rostfreien Stahl grades, ensuring efficient adoption on the shop floor. Consult Metav Werkzeuge for tailored recommendations on Walter Tools' Tiger·tec Gold WMP20G inserts to enhance process stability and achieve longer tool life Technical data Article number: DCMT11T308-FM4-WMP20G-WALTER Designation: DCMT11T308-FM4 Full designation: DCMT11T308-FM4 WMP20G Product type: turning insert Manufacturer: Walter Tools Facts Plate size: 11 Plate thickness: T3 Corner radius: 0.8 mm Clearance angle: 7° Plate form: Rhombus 55° Tolerance class: M Special features Series: Tiger·tec Gold Grade: WMP20G Chipbreaker: FM4 Coated cemented carbide Application: rostfreien Stahl (stainless steels), medium to robust conditions FAQ What materials is this insert suitable for? The DCMT11T308-FM4 WMP20G insert is designed primarily for rostfreien Stahl and works reliably under medium to robust machining conditions. How does the FM4 chipbreaker affect machining? The FM4 chipbreaker on the Walter Tools grade controls chip shape and promotes secure chip evacuation, which helps maintain process stability and reduces the risk of built-up edge. What does the Rhombic 55° shape provide? A Rhombic 55° geometry offers a positive cutting action with balanced strength, supporting lower cutting forces and improved surface finish on turned components. Is the insert compatible with standard ISO toolholders? Yes, the insert follows the common ISO-style DCMT designation and T3 thickness for straightforward compatibility with matching toolholder designs. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names remain the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only and do not imply any association between Metav Werkzeuge and the named brands. The offered item is an original, factory-new product of the manufacturer.
DCMT11T308-FM4 WMP20S Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Silver coating and the WMP20S carbide grade for secure chip formation and consistent performance in demanding stainless steel operations; the robust FM4 chipbreaker and rhombic geometry ensure reliable machining and reduced downtime. Order the DCMT11T308-FM4 WMP20S turning insert directly via Metav Werkzeuge or consult the Metav team for application-specific advice. DCMT11T308-FM4 WMP20S turning insert for stainless steel, Tiger·tec Silver — Walter Tools The DCMT11T308-FM4 WMP20S is a rhombic 55° turning insert designed for medium to robust machining of stainless steels, combining a coated carbide grade with a proven FM4 chipbreaker. Tiger·tec Silver coated carbide grade Optimised for stainless steel (ISO M) Rhombic 55° geometry, 0.8 mm corner radius FM4 chipbreaker for reliable chip control Consistent cutting in stainless steel with Tiger·tec Silver The Tiger·tec Silver technology and the WMP20S carbide grade deliver a balance of wear resistance and toughness that supports stable chip formation when machining stainless steel (ISO M). This coating technology reduces built-up edge and extends cutting life under elevated temperatures typical for these materials. Where thermal load and material ductility can cause inconsistent chips, the FM4 chipbreaker assists in producing controllable, segmented chips, which lowers the risk of re-cutting and improves cycle reliability. The result is fewer tool changes and a steadier production flow. Geometry engineered for surface quality and tool life The rhombic 55° form and a 0.8 mm corner radius offer an effective compromise between strength and finish. The insert’s 7° relief reduces rubbing at the flank, while the T3 thickness contributes to rigidity in interrupted or heavier cuts. Together, these geometric features reduce vibration and distribute cutting forces more evenly, which enhances both tool life and part surface quality. For components where a finer finish is required, the geometry supports lower feed rates without sacrificing edge stability. Practical benefits for workshop productivity The combination of a coated carbide grade, robust chip control and standard DCMT clamping compatibility simplifies integration into existing turning setups. The FM4 chipbreaker is tailored to the workpiece behaviour of stainless steels, promoting predictable chip shapes that ease handling and swarf management. As a result, tool-setting times and unplanned stoppages are reduced, delivering measurable efficiency gains across short and long production runs. The insert is suitable for medium to robust applications where process consistency is prioritised. For production-ready stainless steel turning with Walter Tools’ Tiger·tec Silver technology, contact Metav Werkzeuge for technical matching and availability — Metav Werkzeuge can advise on optimal cutting parameters and delivery options at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: DCMT11T308-FM4-WMP20S-WALTER Article: DCMT11T308-FM4 WMP20S Manufacturer: Walter Tools Series: Tiger-tec Silver Facts Insert shape: Rhombus 55° Insert size: 11 mm Thickness: T3 Corner radius: 0.8 mm Relief angle: 7° Chipbreaker: FM4 Special features Coating technology: Tiger·tec Silver Carbide grade: WMP20S (coated cemented carbide) Optimised for: stainless steel (ISO M) Application focus: medium to robust cutting conditions Insert designation: DCMT11T308-FM4 WMP20S FAQ What materials is this insert best suited for? The DCMT11T308-FM4 WMP20S insert is engineered primarily for stainless steel (ISO M) applications, where its coated grade and chipbreaker promote secure chip formation. How does the FM4 chipbreaker affect machining? The FM4 chipbreaker on this Walter Tools insert produces predictable chip shapes for stainless steels, which improves swarf management and reduces the risk of built-up edge during medium to robust cuts. What advantages does the rhombic 55° geometry provide? A rhombic 55° form with a 0.8 mm corner radius balances edge strength and surface finish: it lowers vibration, supports interrupted cuts and helps achieve consistent part quality. Is this insert compatible with standard toolholders? Yes, the DCMT11T308-FM4 WMP20S follows standard DCMT clamping dimensions and can be used in holders designed for this insert form and size. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand presentation: Walter Tools), headquartered in Tübingen, is among the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and product designations remain the property of their respective owners. Brand names and protected terms are cited solely for explanatory purposes; no affiliation between our company and the named brands is implied. The offered article is an original, factory-new product of the manufacturer.
DCMT11T308-FM4 WSM01 WSM01 Wendeplatten - Walter Tools
Take advantage of the combination of high process security, reliable chip control and long tool life for consistent production results; purchase the insert directly via Metav Werkzeuge or consult our advisers for application-specific recommendations. DCMT11T308-FM4 WSM01 — Turning insert (Tiger‑tec Silver), Walter Tools, FM4 chipbreaker, 7° clearance DCMT11T308-FM4 WSM01 is a precision turning insert designed for demanding machining of heat‑resistant alloys and stainless steels, offering stable cutting edges and predictable chip formation for industrial turning applications. Tiger‑tec Silver coating for long tool life Suitable for stainless steels (M) and superalloys (S) FM4 chipbreaker for reliable chip control 7° clearance and 0.8 mm nose radius for secure engagement Improved process reliability through optimised coating and geometry The insert uses a coated carbide grade from the Tiger‑tec Silver series that is formulated for severe conditions and reduced wear. The combination of a robust coating and the WSM01 substrate reduces flank and crater wear, which translates into longer tool life and fewer tool changes on the shop floor. For production environments where uptime and repeatability matter, this means fewer interruptions and more predictable component quality. Consistent chip control and stable cutting performance With the FM4 chipbreaker and a rhombus 55° form, the insert delivers controlled chip formation even when cutting materials that tend to produce stringy or serrated chips. The 7° clearance angle and 0.8 mm nose radius promote a secure cutting condition that helps avoid built-up edge and ensures dimensional stability. These features together enable efficient evacuation of chips and reduce the risk of surface damage, thereby improving first‑pass yield in serial turning operations. Application fit and machining advantages for demanding materials This grade is classified for machining stainless steels (ISO group M) and heat‑resistant superalloys (ISO group S). The alloy‑specific design stabilises the cutting edge under high temperatures and supports secure chip formation when machining tough, adhesive materials. In practice, this insert is suitable for finishing and medium turning where consistent surface integrity and edge security are required; the geometry and material pairing support both tool life and process security, lowering overall production cost per part. Contact Metav Werkzeuge for tailored application advice and ordering of Walter Tools turning inserts — phone +49 2822 7131930 or eMail info@metav-werkzeuge.com Technical Data SKU: DCMT11T308-FM4-WSM01-WALTER Label: Drehwendeschneidplatte DCMT11T308-FM4 WSM01 Walter Tools Manufacturer: Walter Tools Product type: Drehwendeschneidplatte Series: Tiger‑tec Silver Grade: WSM01 Core specifications Size: 11 mm Insert shape: Rhombus 55° Nose radius: 0.8 mm Clearance angle: 7° Chipbreaker: FM4 Thickness: T3 Tolerance class: M Applications & features Coated carbide grade (WSM01) Suitable for stainless steels (M) and superalloys (S) Stable chip formation and secure cutting edge Designed for demanding turning operations FAQ Which materials are best machined with this insert? The DCMT11T308-FM4 WSM01 insert is intended primarily for stainless steels (ISO group M) and heat‑resistant alloys (ISO group S); the Tiger‑tec Silver grade supports stable cutting in these materials. What benefits does the FM4 chipbreaker provide? The FM4 chipbreaker ensures reliable chip control and consistent evacuation, reducing the risk of entanglement and improving surface quality during turning. How does the insert geometry affect cutting performance? The rhombus 55° form, 7° clearance and 0.8 mm nose radius combine to provide secure engagement and dimensional stability, helping to avoid built‑up edge and maintain repeatable component tolerances. Is this insert suitable for finishing operations? Yes, the insert’s geometry and the WSM01 coated carbide grade are well suited to finishing and medium turning where surface integrity and edge security are priorities. Can this grade reduce tool change frequency? The Tiger‑tec Silver coating and stable substrate promote longer tool life and more consistent wear behaviour, which typically reduces the need for frequent tool changes. Manufacturer: Walter Tools; Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DCMT11T308-FM4 WSM10S WSM10S Wendeplatten - Walter Tools
Benefit from the combination of the WSM10S Tiger·tec Silver grade, the FM4 chipbreaker and the Rhombus 55° geometry for stable edge life and consistent performance in demanding materials; order directly via Metav Werkzeuge or request consultation from our technical team for process matching. DCMT11T308-FM4 WSM10S indexable turning insert – Tiger·tec Silver for stainless steel and superalloys | Walter Tools The DCMT11T308-FM4 WSM10S is an indexable turning insert engineered for demanding turning applications, offering a coated-carbide grade optimised for machining stainless steel and heat-resistant alloys; suited to industrial production where edge stability and predictable chip control are required. Tiger·tec Silver coating for enhanced wear resistance Optimised FM4 chipbreaker for controlled chip formation 7° relief angle for secure cutting edge support Rhombus 55° form with 0.8 mm corner radius Extended wear life through advanced grade and coating The combination of WSM10S and the Tiger·tec Silver coating delivers elevated thermal and wear resistance compared with conventional grades. This coated carbide formulation is designed to resist edge degradation when machining stainless steel and other workpiece groups meeting ISO M and S classifications, reducing flank wear and the need for frequent index changes. For production environments this means longer tool life and fewer interruptions to machining sequences, improving cumulative productivity and lowering per-part tooling costs. Geometry and chip control that support consistent surface quality A geometric package comprising the FM4 chipbreaker, Rhombus 55° shape and a 0.8 mm corner radius yields controlled chip formation and dependable cutting forces. The moderate lead angle associated with the rhombic form promotes stable engagement at turning feeds typical for stainless applications, while the 7° relief angle balances strength and clearance to protect the cutting edge. Together these features support repeatable surface finishes and dimensional stability across batch runs. Designed for challenging alloys and process security The insert is targeted at the ISO material groups S and M — that is, heat-resistant superalloys, titanium and stainless steel — where poor heat conduction and work-hardening tendencies demand a robust grade and secure edge. The WSM10S grade reduces the tendency for built-up edge and supports a steady chip break to avoid tangling. In practice, the result is fewer rejects, improved process reliability and a more predictable maintenance cycle for tool assemblies in high-value component manufacturing. Practical selection and integration guidance for workshops The insert’s designation and dimensions simplify matching to toolholders designed for DCMT-size parts; the T3 thickness and standard clamping geometries permit secure seating in common tool systems. When selecting parameters, prioritise stable clamping and moderate depths of cut when first proving a new programme; the combination of FM4 chip control and the Tiger·tec Silver coating allows for progressive optimisation. For tailored recommendations on cutting data, holder compatibility and economical batch strategies, Metav Werkzeuge’s technical advisors can assist with process-specific guidance. Contact Metav Werkzeuge today to specify Walter Tools DCMT11T308-FM4 WSM10S for stainless-steel and superalloy turning and to receive application-oriented advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number / SKU: DCMT11T308-FM4-WSM10S-WALTER Designation: DCMT11T308-FM4 WSM10S Manufacturer: Walter Tools Facts Plate size: 11 Relief angle: 7° Corner radius: 0.8 mm Thickness: T3 Shape: Rhombus 55° Special features Grade: WSM10S Coating family: Tiger·tec Silver Chipbreaker: FM4 Tolerance class: M Material groups: S (superalloys/titanium) ; M (stainless steel) FAQ Which materials is this insert suitable for? The DCMT11T308-FM4 WSM10S insert is specified for ISO groups M and S, meaning it is suitable for stainless steel and heat‑resistant superalloys or titanium, where the WSM10S grade provides enhanced edge stability. What benefits does the FM4 chipbreaker provide? The FM4 chipbreaker delivers controlled chip formation and reliable chip evacuation for turning operations in ductile and work‑hardening alloys, improving process security when using the DCMT11T308-FM4 WSM10S insert. How does the Tiger·tec Silver coating affect performance? The Tiger·tec Silver coating on the WSM10S grade increases wear resistance and thermal protection, which contributes to longer tool life and more consistent cutting-edge behaviour in demanding materials. What geometry details should be considered when selecting holders? The rhombic 55° form, T3 thickness and 11 size require holders compatible with DCMT inserts; ensure the holder provides stable clamping and correct seating for the DCMT11T308-FM4 WSM10S to achieve intended performance. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools) is among the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanation. There is no connection between our company and the mentioned brands. The offered item is an original, brand‑new product of the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com