DNGA150612TM-2 WBH10C WBH10C Wendeplatten - Walter Tools
Take advantage of the WBH10C CBN grade and the rhombic 55° geometry to secure stable, wear-resistant hard turning; the negative 0° rake and 1.2 mm corner radius enhance process reliability and predictable tool life. Order or request technical advice via Metav Werkzeuge for seamless integration into production. DNGA150612TM-2 WBH10C turning indexable insert — Walter Tools, CBN grade for hard turning The DNGA150612TM-2 WBH10C is a rhombic 55° CBN-coated turning insert engineered for hard and pre-hardened steels, offering high wear resistance and stable cutting performance in demanding hard‑turning applications. CBN grade WBH10C for hard materials Rhombic 55° geometry for stable cutting Negative 0° rake for robust chip control 1.2 mm corner radius for high edge strength Improved wear resistance for hard‑turning processes The combination of the WBH10C CBN grade and the Walter CBN series delivers notably higher wear resistance when machining hardened steels. CBN is specifically designed for high‑hardness applications, which means the insert maintains cutting edge integrity under elevated contact stresses. This results in longer intervals between index changes and more predictable production cycles, supporting tighter tolerances and consistent surface quality. The result is an economically efficient choice for shops facing frequent hard‑turning tasks. Geometry engineered for stability and chip control The rhombic 55° shape and the negative 0° relief provide a robust cutting geometry that minimises vibration and supports steady cutting forces. The integrated chipbreaker 2 promotes controlled chip formation in hard materials, reducing the risk of built-up edge and improving process stability. Together with the 1.2 mm corner radius, the insert offers a balance of strength and form retention that benefits interrupted cuts and medium‑to‑heavy cutting conditions, ensuring reliable component finish and dimensional repeatability. Process benefits and application scope Designed for the Walter CBN / Hartstoff series, this insert is optimised for hardened and pre‑hardened steels (material group H). The stable edge behaviour and coated CBN compound translate into higher process security and consistent results on serial production runs. For manufacturers requiring secure hard machining of shafts, rings or hardened housings, the insert reduces downtime related to tool wear and rework, improving throughput without compromising surface integrity. Integration, specification and shopfloor guidance The insert’s designation and core dimensions align with standard clamping systems for DNGA‑style inserts, simplifying retrofit into existing toolholders. Key measurable features include the 15 mm size and a thickness code 06, supporting compatibility checks during tool selection. The tolerance class G and the Walter series designation signal a production‑grade component suitable for industrial turning cells where repeatability and predictable performance are priorities. For a production‑oriented recommendation on employing WBH10C inserts in a specific machining process, contact Metav Werkzeuge for tailored advice, availability and order coordination — eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data Article number: DNGA150612TM-2-WBH10C-WALTER Designation: DNGA150612TM-2 WBH10C Product type: Turning indexable insert (Drehwendeschneidplatte) Manufacturer: Walter Tools Core specifications Size: 15 mm Corner radius: 1.2 mm Relief angle: 0° (negative) Thickness code: 06 Geometry: Rhombus 55° Materials & features Grade/coating: WBH10C (CBN-coated) Series: Walter CBN / Hartstoff Chipbreaker: 2 Tolerance class: G Suitable for: hardened steels (H), pre-hardened steel applications FAQ Is this insert suitable for interrupted hard turning? The DNGA150612TM-2 WBH10C from Walter Tools is designed for hard turning and, thanks to the robust CBN grade and 1.2 mm corner radius, is well suited to many interrupted cutting scenarios. Which materials can be machined with this grade? The WBH10C grade is targeted at hardened steels and pre‑hardened components; the insert’s properties prioritise wear resistance and stable edge life for high‑hardness groups. How does the negative 0° rake affect cutting performance? A 0° (negative) relief increases edge strength and resistance to chipping, improving process security during heavy or unstable cuts while maintaining consistent chip formation with the integrated chipbreaker. Can this insert be used in standard DNGA toolholders? The designation DNGA150612TM‑2 indicates compatibility with DNGA‑style toolholders; matching the insert geometry to the clamping system ensures correct seating and repeatable performance. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Walter Tools is part of the worldwide offering of precision metalworking solutions. The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is among the leading manufacturers of precision tools for metal machining and is part of the Swedish Sandvik group. Protected trademarks and trade names belong to their respective owners. Brand names are mentioned solely for explanatory purposes. There is no connection between our company and the manufacturers named. The offered item is original and brand‑new.
DNGA150612TM-2 WBH20 A Wendeplatten - Walter Tools
Benefit from the combination of CBN-grade WBH20 and a Rhombic 55° geometry for reliable hard turning: the insert delivers high wear resistance and process stability when machining hardened and pre-hardened steels, helping to maintain consistent part quality and longer tool life. Order through Metav Werkzeuge or request cutting data for integration into production. DNGA150612TM-2 WBH20 CBN Turning Insert, Rhombus 55° – Walter Tools A DNGA150612TM-2 WBH20 turning insert engineered for hard turning and finishing of hardened steels and pre‑hardened materials using a CBN grade for sustained performance in high‑wear operations CBN grade WBH20 for hard turning Rhombic 55° geometry for versatile cuts 0° negative rake for stable machining 1.2 mm corner radius for robust edge Proven wear resistance for hardened materials The CBN‑based WBH20 grade is designed specifically for machining hardened steels, where thermal and abrasive stresses are high. The use of cubic boron nitride as the cutting material gives superior wear resistance and a stable cutting edge, so tool changes are less frequent and component tolerances remain consistent over long production runs. For operations that demand repeatable results on hard workpieces, this grade reduces unplanned downtime and supports predictable batch throughput. Geometry that secures process stability and surface quality The Rhombic 55° form combined with a 0° negative rake produces a mechanically strong cutting edge suited to interrupted cuts and demanding turning tasks. The 1.2 mm corner radius enhances edge strength and contributes to improved surface finish in many applications. These geometric choices mean the insert resists chipping and maintains dimensional stability, which is especially valuable in finishing passes where part integrity and surface quality are critical. Practical application and integration into production Suitable for hard turning and machining of pre‑hardened steel and similar high‑hardness materials, the insert is part of the Walter CBN / hard material series and is provided in the ISO designation DNGA150612TM‑2 WBH20. The robust grade and form support both roughing and finishing strategies with fewer tool changes. When integrating the insert into existing toolholders and programmes, the stable edge and optimised chip control help to reduce cycle time variability while supporting consistent component quality. For process‑critical hard turning tasks, contact Metav Werkzeuge to receive tailored cutting parameters and integration advice for Walter Tools CBN inserts. Technical Data Article number: DNGA150612TM-2-WBH20-WALTER Product type: Turning indexable insert (drehwendeschneidplatte) ISO designation: DNGA150612TM-2 WBH20 Series: Walter CBN / hard material Facts Corner radius: 1.2 mm Insert size: 15 mm Relief angle: 0° (negative) Thickness code: 06 Chipbreaker: 2 Special features Grade: WBH20 (CBN cutting material) Material application: hardened steels (H) Tolerance class: G Designation without grade: DNGA150612TM-2 Execution: A Manufacturer: Walter Tools FAQ What workpiece materials is this insert suited for? The DNGA150612TM‑2 WBH20 insert is specified for hardened steels and is suitable for pre‑hardened steel applications; the WBH20 CBN grade targets high‑hardness machining tasks. Is the insert suitable for interrupted cuts and roughing operations? Yes, the combination of 0° negative rake and a 1.2 mm corner radius gives a robust cutting edge that is well suited to interrupted cuts and demanding roughing sequences with the Walter Tools CBN insert. How does the WBH20 grade affect tool life compared with conventional grades? The WBH20 CBN grade emphasises wear resistance and edge stability for hard turning, which typically results in longer in‑service life and fewer tool changes when machining high‑hardness workpieces. Can this insert be used for finishing to tight surface finish requirements? When applied with appropriate cutting parameters, the insert’s Rhombic 55° geometry and stable edge can produce consistent surface quality in finishing passes on hardened materials. Is special tooling required to use the DNGA150612TM‑2 insert? Compatibility depends on the toolholder type, but the ISO designation DNGA150612TM‑2 WBH20 is compatible with holders designed for DNGA inserts; correct clamping and recommended cutting data from Metav Werkzeuge ensure reliable performance. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no affiliation between Metav Werkzeuge and the referenced brands. The offered item is an original, factory‑new product from the manufacturer.
DNGA150612TM-2 WBH30 A Wendeplatten - Walter Tools
Take advantage of the combination of CBN wear resistance, a Rhombic 55° geometry and a stable negative rake for predictable tool life and process security — ideal for hard-turning tasks. Order the insert directly via Metav Werkzeuge or request application guidance from their consultants. DNGA150612TM-2 WBH30 — Indexable turning insert for hardened steels | Walter Tools A robust DNGA150612TM-2 WBH30 indexable turning insert designed for hard turning and performance machining of hardened steels in demanding production environments CBN grade WBH30 for hard turning Rhombic 55° form for versatile clamping Negative rake 0° for stable cutting 1.2 mm corner radius for robust edge High-performance grade for hard turning and consistent production The insert is built on a CBN cutting-grade basis (WBH30) engineered specifically for machining hardened steels; this makes it a fitting choice where high wear resistance and cutting-edge stability are decisive. The use of cubic boron nitride as the cutting material reduces flank and crater wear under elevated contact temperatures, which in turn supports a steady process window and predictable tool life. For production planners and process engineers, this means fewer tool changes and more consistent part quality — a rational advantage for batch and continuous turning operations. Geometry that stabilises chip flow and surface quality A Rhombus 55° shape combined with a negative rake 0° creates a geometry that distributes cutting forces favourably and supports secure clamping in standard turning toolholders. The specified chipbreaker 2 aims to break and evacuate chips effectively during hard cutting, assisting in maintaining surface integrity and reducing the risk of built-up edge. These geometric choices translate into measurable benefits: improved repeatability of component geometry and reduced rework rates in high-hardness applications. Robust edge design for longer tool life and reduced downtime The pronounced 1.2 mm corner radius lends mechanical strength to the cutting edge, helping to withstand the impact of interrupted cuts and high contact stresses common in hard turning. The plate dimensions and thickness contribute to a stable seating in the toolholder, supporting vibration damping and edge security. The result is a lower likelihood of premature edge chipping and longer intervals between indexings or insert replacements, which supports higher overall equipment effectiveness (OEE) on the shopfloor. Application scope and compatibility with hard-turning workflows Supplied within the Walter CBN / hard material series, this insert is intended for the machining of hardened workpiece materials as specified by ISO material group H. It is suitable for applications such as finishing and hard roughing of quenched steels where abrasive wear resistance and edge robustness are essential. The insert’s negative rake and rhombic form permit its use in a broad range of standard turning toolholders; Metav Werkzeuge can advise on optimal seatings and insert orientations for specific machine-tool combinations to ensure process security and component conformity. For precise application advice and to discuss suitability for specific hardened materials, contact Metav Werkzeuge for tailored recommendations at info@metav-werkzeuge.com or call +49 2822 7131930 — the team can provide machining tips and selection support for Walter Tools CBN grades. Technical Data Article number: DNGA150612TM-2-WBH30-WALTER Designation: DNGA150612TM-2 WBH30 Product type: Indexable turning insert (drehwendeschneidplatte) Series: Walter CBN / Hartstoff Manufacturer: Walter Tools Facts Plate size: 15 Corner radius: 1.2 mm Relief / rake: 0° (negative) Plate thickness: 06 Chipbreaker: 2 Special features Cutting grade: WBH30 (CBN) Plate form: Rhombus 55° Material application: hardened steels (H) Suitable for pre-hardened steels and hard turning tasks FAQ What workpiece materials is this insert suited for? The DNGA150612TM-2 WBH30 indexable turning insert is engineered for hardened steels (ISO group H) and is particularly effective in hard-turning scenarios where CBN provides superior wear resistance. How does the WBH30 grade improve machining of hardened components? WBH30 uses a CBN-based grade that resists abrasive flank wear and maintains cutting-edge security under high contact temperatures, improving process stability and component surface finish during hard cutting. What is the significance of the Rhombus 55° form? The Rhombus 55° form offers versatile clamping options and favourable cutting force distribution, making the insert compatible with common turning holders and beneficial for both finishing and robust hard-turning operations. How does the negative rake of 0° affect cutting performance? A negative rake 0° increases edge strength and reduces the likelihood of chipping in interrupted or heavy cuts, providing a more stable cutting action when machining hardened materials. Can this insert handle interrupted cuts or tough geometries? Yes; the 1.2 mm corner radius and CBN grade WBH30 are selected to withstand high local stresses, making the insert suitable for interrupted cuts and demanding hard-turning profiles. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The item offered is an original, factory-new product of the manufacturer.
DNGA150612TM-M2 WBH10 Wendeplatten - Walter Tools
High-performance CBN grade and robust negative geometry combine to deliver long tool life and repeatable results in hard turning; benefit from the WBH10 wear resistance and the stable 1.2 mm corner radius for predictable surface quality. Order this indexable insert directly via Metav Werkzeuge or ask the consultants for application support. DNGA150612TM-M2 WBH10 CBN indexable turning insert for hardened steel — Walter Tools The DNGA150612TM-M2 WBH10 is an indexable CBN turning insert designed for hard machining of hardened steels and similar wear‑resistant materials, offering a combination of abrasion resistance and reliable performance in repetitive production. CBN grade WBH10 for hard machining Stable cut with 1.2 mm corner radius Rhombic 55° geometry for versatile turning Negative 0° rake for robust cutting action Longer productivity through wear‑resistant cutting grade The application of a CBN cutting material reduces flank wear and extends tool life when machining hardened steels, making it a cost‑effective choice for serial production of heat‑treated components. The WBH10 grade is engineered for high abrasive resistance and dimensional stability, which lowers the frequency of index changes and helps maintain consistent part quality. By choosing a dedicated CBN insert, process windows become more stable and workpiece tolerances are easier to hold during long runs. Geometry and edge design for secure machining A Rhombus 55° shape paired with a corner radius of 1.2 mm provides a compromise between strength at the cutting edge and the ability to achieve acceptable surface finish in finishing and semi‑finishing passes. The negative 0° rake contributes to a robust cutting edge that resists chipping under heavy interrupted cuts and high radial loads. The indexable insert format permits quick reorientation and replacement, reducing machine downtime and keeping cycle times low while preserving operator safety and process repeatability. Practical suitability and machining focus This insert is specified for machining hardened steels and is appropriate where high hardness and abrasive wear dictate use of CBN technology. The M2 chipbreaker supports controlled chip formation in hard turning operations, improving evacuation and reducing the risk of built‑up edge. Tolerance class G and the standard 15 mm size family allow straightforward integration into common toolholder systems that accept DNGA‑format inserts, enabling fast adoption within existing turning setups and reliable production performance. For detailed application guidance on Walter Tools CBN inserts and to confirm suitability for specific hard turning tasks, contact Metav Werkzeuge for tailored recommendations and ordering support at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: DNGA150612TM-M2-WBH10-WALTER Designation: DNGA150612TM-M2 WBH10 Product type: Indexable turning insert Facts Insert size: 15 mm Corner radius: 1.2 mm Plate thickness: 06 Geometry: Rhombus 55° Rake angle: 0° (negative) Tolerance class: G Special features Grade: WBH10 (CBN) Chipbreaker: M2 Series: Walter CBN / Hartstoff Application focus: Hardened steels (H) Execution: A FAQ What materials is this insert suited to machine? The insert is optimised for hardened steels; the WBH10 CBN grade is selected specifically to handle the abrasive conditions encountered when hard turning. How does the negative 0° rake affect machining performance? A 0° negative rake produces a sturdier cutting edge, improving resistance to edge breakouts and favouring stable performance under higher cutting forces in hard material removal. What does the DNGA designation indicate? DNGA denotes the insert shape and clamping orientation; this indexable insert format suits toolholders designed for DNGA geometry and supports rapid index changes. Why choose a 1.2 mm corner radius for hard turning? A 1.2 mm corner radius balances edge strength and surface finish, offering improved edge life while still enabling attainable surface quality in finishing operations. Is the M2 chipbreaker appropriate for interrupted cuts? The M2 chipbreaker provides controlled chip formation in hard turning and contributes to reliable evacuation, which can help in conditions with mild interruption; heavy interruptions should be evaluated case‑by‑case. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Walter Tools is part of the Walter AG group and is recognised for precision tools in metalworking. Protected trademarks and trade names remain the property of their respective owners and are mentioned solely for explanation. There is no connection between our company and the named brands beyond the sale of original, factory‑new goods of the manufacturer.
DNGA150612TS-2 WBK20 WBK20 Wendeplatten - Walter Tools
Take advantage of the combination of CBN cutting grade, a 55° rhombic form and a 1.2 mm corner radius for reliable hard-turning performance; order the insert directly via Metav Werkzeuge or consult the specialists for application matrices and process parameters. DNGA150612TS-2 WBK20 indexable turning insert by Walter Tools — CBN grade for hard materials the DNGA150612TS-2 WBK20 is an indexable turning insert designed for demanding hardened-steel applications and heavy-wear tasks, combining a CBN cutting grade with a robust rhombic 55° geometry CBN cutting grade WBK20 for hardened materials 55° rhombic form for versatile turning 0° negative rake for stable cutting 1.2 mm corner radius for robust edge strength Consistent material removal and predictable tool life The combination of the CBN cutting grade WBK20 and the rhombic 55° geometry delivers high process stability during hard turning. CBN is especially suited for abrasive, hardened steels and similar hard materials; its microstructure provides a wear-resistant cutting edge that reduces flank wear and extends productive life. The 0° negative rake enhances mechanical strength at the cutting edge, enabling stable chip formation under interrupted cuts. These technical choices translate into fewer tool changes and more consistent batch throughput, supporting predictable cycle times and lower overall machining costs. Improved edge strength and surface integrity A 1.2 mm corner radius and the specified chipbreaker ensure a robust cutting edge and controlled chip flow. The larger corner radius reduces local stress concentration at the cutting tip and improves surface finish in finishing and semi-finishing passes. The chipbreaker configuration promotes short, manageable chips for turning operations, which benefits tool life and helps maintain workpiece integrity. For production environments where repeatability and surface quality matter, these geometric features combine to reduce rework and support higher first-pass yields. Integration into tool systems and process planning The insert follows established indexable turning conventions, allowing straightforward integration with compatible toolholders and tool-setting routines. The plate thickness code and insert form are consistent with common turning systems, simplifying tool inventory management. Process planners gain from the WBK20 grade’s focus on wear resistance: machining strategies for hardened components can be optimised around predictable tool-change intervals. When selecting cutting parameters, consider the workpiece material class and consult the product matrix for best-fit cutting data to achieve the intended performance. Application suitability and validation This insert targets operations where hard materials and high wear conditions are the norm: hardened-steel components, certain castings and superalloy tasks (where applicable). Material suitability should be checked against the manufacturer’s product matrix to ensure the best match of grade and cut. The insert’s combination of CBN technology and robust geometry supports both high-throughput production and challenging one-off repair or refurbishment jobs where edge durability is decisive. Contact Metav Werkzeuge for tailored application advice on Walter Tools CBN inserts and request the cutting data matrix or material suitability guide via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: DNGA150612TS-2-WBK20-WALTER Product type: Indexable turning insert (Drehwendeschneidplatte) Brand: Walter Tools Designation: DNGA150612TS-2 WBK20 Series: Walter Schneidstoffsorte - Serie offen Facts Corner radius: 1.2 mm Rake angle: 0° (negative) Form: Rhombus 55° Size code: 15 Thickness code: 06 Chipbreaker: 2 Tolerance class: G Execution: A Special features Cutting material: CBN cutting grade (WBK20) Targeted for hardened and high-wear applications Suitable for process-stable turning and interrupted cuts Series description: CBN for hard, abrasive materials (check product matrix for exact material match) FAQ What materials is this insert intended for? The DNGA150612TS-2 WBK20 insert from Walter Tools is a CBN grade designed primarily for hardened steels and high-wear tasks; suitability for specific alloys or castings should be verified in the manufacturer’s material matrix. How does the 0° negative rake affect cutting performance? A 0° negative rake increases edge strength and resistance to mechanical shock, making the insert suitable for robust cutting conditions and intermittent cuts without sacrificing process stability. What benefit does the 1.2 mm corner radius provide? The 1.2 mm corner radius improves edge robustness and contributes to a better surface finish in finishing passes while reducing the likelihood of premature chipping under heavy loads. Is the insert compatible with standard tooling systems? The DNGA150612TS-2 form and codes conform to common indexable turning standards, allowing integration with compatible toolholders; toolholder selection should follow the holder manufacturer’s recommendations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik-Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DNGG110402M-MN3 WN10 Wendeplatten - Walter Tools
Optimise turning operations with the WN10 uncoated carbide grade together with the MN3 chipbreaker and a rhomboid 55° geometry for reliable chip control and consistent edge performance; order the insert directly via Metav Werkzeuge or consult the technical team for suitability. DNGG110402M-MN3 WN10 indexable turning insert, Rhombus 55° – Walter Tools A DNGG110402M-MN3 WN10 indexable turning insert intended for versatile turning tasks, featuring an MN3 chipbreaker and an uncoated carbide grade for predictable machining behaviour Uncoated carbide for predictable wear MN3 chipbreaker for stable chip control Rhombus 55° geometry for versatile turning 0.2 mm corner radius for fine edge detail Increase process stability with proven grade and geometry The combination of WN10 as an uncoated carbide grade and the MN3 chipbreaker is aimed at delivering stable cutting conditions and reliable chip formation in a range of workshop operations. The rhomboid 55° profile provides a flexible cutting approach that suits both finishing passes and light to medium roughing. A 0° negative rake contributes to a robust cutting edge, reducing the risk of chipping when intermittent cuts or interrupted cuts occur. These characteristics translate into fewer insert changes and a smoother production flow. Achieve finer surfaces and predictable edge life A 0.2 mm corner radius increases edge strength while supporting a good surface finish on turned components; this radius balances durability and the ability to produce detailed profiles. The G tolerance class and defined insert thickness ensure consistent seating and repeatable positioning in standard toolholders, which is essential for dimensional accuracy in production runs. Consequently, machining results become more predictable and inspection effort can be reduced. Simple selection and integration into the workshop Selection should follow the product matrix to confirm material compatibility and cutting data; the insert’s MN3 chip control works well where stable chips are required. The DNGG110402M-MN3 WN10 indexable insert is supplied in the Walter Schneidstoffsorte series and is suitable for general turning applications where an uncoated carbide grade is preferred. For adaptation to existing toolholders and process windows, consult the technical documentation or Metav Werkzeuge for tailored recommendations and cutting-parameter guidance. Contact Metav Werkzeuge for tailored cutting solutions based on the Walter Tools WN10 grade and MN3 chipbreaker — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: DNGG110402M-MN3-WN10-WALTER Label: Drehwendeschneidplatte DNGG110402M-MN3 WN10 Walter Tools Manufacturer: Walter Tools ISO designation: DNGG110402M-MN3 WN10 Internal ID: DNGG110402M-MN3-WN10-WALTER Material: Katalogabhängig Numbers / Core technical data Corner radius: 0.2 mm Rake angle: 0° (negative) Insert size: 11 Thickness: 04 Tolerance class: G Chipbreaker: MN3 Designs / Special features Shape: Rhombus 55° Grade: WN10 (uncoated carbide) Series: Walter Schneidstoffsorte - Serie offen Designation without grade: DNGG110402M-MN3 Execution: G FAQ Which materials suit this insert best? The DNGG110402M-MN3 WN10 insert is an uncoated carbide grade; material suitability should be checked against the manufacturer’s product matrix to confirm optimal application. How does the MN3 chipbreaker affect machining? The MN3 chipbreaker promotes stable chip formation and evacuation, reducing the risk of built-up edge and helping to maintain a consistent cutting force during turning. What advantages does the rhombus 55° geometry provide? A rhombus 55° geometry offers versatile approach angles for general turning and profile work, enabling both accurate finishing and adaptable feed strategies. What does a 0° negative rake mean in practice? A 0° negative rake produces a stronger cutting edge, improving resistance to impact and crater wear in interrupted or heavy cuts while maintaining acceptable cutting forces. Can the insert achieve fine surface finishes? With a 0.2 mm corner radius and correct cutting parameters, the insert can deliver fine surface finishes while preserving edge life through improved strength. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany, info@walter-tools.com Protected trademarks and trade names remain the property of their respective owners. Brand names and protected trade designations are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered article is original and factory-new from the manufacturer Walter Tools. The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is part of the Sandvik group.
DNGG110402M-MN3 WNN10 WNN10 Wendeplatten - Walter Tools
Take advantage of the combination of the WNN10 coated carbide grade, the MN3 chipbreaker and the rhombic 55° geometry for reliable productivity and consistent chip control; order directly via Metav Werkzeuge or consult the technical team for application-specific cutting data. DNGG110402M-MN3 WNN10 turning insert — rhombic 55° form, coated carbide, Walter Tools The DNGG110402M-MN3 WNN10 is a rhombic 55° turning insert designed for general to semi-finish turning where stable chip formation and repeatable tool life are required, featuring a 0° negative rake and a 0.2 mm corner radius Coated carbide grade WNN10 MN3 chipbreaker for controlled chips Rhombic 55° geometry for versatile turning 0° negative rake for robust cutting Optimised productivity through proven grade and chip control The combination of the WNN10 coated carbide and the MN3 chipbreaker is aimed at improving process stability and reducing secondary operations. The coating on the sintered carbide promotes wear resistance while the chipbreaker geometry channels swarf away from the cutting edge, resulting in fewer interruptions during long turning cycles. For machining tasks that demand repeatable performance, this insert supports a steady cycle time and contributes to predictable tool-change intervals, helping to maintain throughput in batch production or continuous turning processes. Robust geometry for secure machining and dimensional consistency A rhombic 55° form together with a 0° negative rake provides a robust cutting corner that tolerates variable workpiece conditions and moderate interruptions. The nominal corner radius of 0.2 mm improves edge strength and reduces the risk of chipping when machining interrupted cuts or tougher material zones. These geometric choices favour dimensional stability and a consistent surface finish, making the insert suitable for routine roughing and semi-finishing operations where tool reliability and part accuracy matter. Easy specification and integration into tool systems The insert is offered in the standard ISO designation DNGG110402M-MN3 WNN10 and fits common toolholders sized for 11 mm inserts and 04 thickness. Compatibility with established clamping systems simplifies inventory handling and toolsetting, while the tolerance class G ensures consistent seating and repeatable indexation. Technical documentation and cutting data from Walter Tools assist in selecting appropriate feeds and speeds for the required application, enabling planners and operators to define efficient process parameters with confidence. Contact Metav Werkzeuge today for application advice, cutting parameters and availability for Walter Tools turning inserts — Metav Werkzeuge provides tailored recommendations and rapid delivery options Technical Data SKU: DNGG110402M-MN3-WNN10-WALTER Label: Drehwendeschneidplatte DNGG110402M-MN3 WNN10 Walter Tools Product type: Drehwendeschneidplatte Facts Insert size: 11 Thickness: 04 Corner radius: 0.2 mm Free angle: 0° (negative) Plate form: Rhombic 55° Tolerance class: G Special features Coating / grade: WNN10 (coated carbide) Chipbreaker: MN3 Series: Walter Schneidstoffsorte - Serie offen Designation without grade: DNGG110402M-MN3 Execution: G FAQ What materials is this insert suitable for? The WNN10 grade and MN3 chipbreaker are intended for a broad range of materials; final suitability should be checked against the Walter Tools product matrix for the DNGG110402M-MN3 WNN10 insert. Can the insert handle interrupted cuts? Yes, the 0° negative rake and a 0.2 mm corner radius provide enhanced edge toughness, so the DNGG110402M-MN3 WNN10 is appropriate for interrupted turning where robust cutting edges are required. Which toolholders accept this insert format? The insert follows the DNGG format and is compatible with holders designed for 11 mm rhombic 55° inserts and 04 thickness, allowing straightforward integration into common clamping systems. How does the MN3 chipbreaker affect finish and swarf control? The MN3 chipbreaker is engineered to produce controlled chips that evacuate reliably, improving swarf management and supporting a stable surface finish during continuous turning operations. Is cutting data available for this insert? Walter Tools provides cutting recommendations for the DNGG110402M-MN3 WNN10; Metav Werkzeuge can supply tailored cutting parameters based on the specific workpiece material and machining conditions. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes and imply no association with our company. The offered item is an original, factory-new product from the manufacturer.
DNGG110404M-MN3 WN10 Wendeplatten - Walter Tools
Benefit from the stable cutting behaviour of the uncoated WN10 carbide grade combined with the MN3 chipbreaker and a 0.4 mm corner radius for consistent chip control and repeatable turning results; order the DNGG110404M-MN3 WN10 directly via Metav Werkzeuge or contact our consultants for material-specific guidance DNGG110404M-MN3 WN10 — Turning insert (Rhombic 55°, 0.4 mm radius) by Walter Tools The DNGG110404M-MN3 WN10 is a rhombic 55° turning insert in an uncoated carbide grade designed for general turning operations, offering a negative 0° rake and an MN3 chipbreaker for controlled chip formation Uncoated carbide WN10 for broad applications Rhombic 55° shape for flexible clamping 0.4 mm corner radius for stable edge MN3 chipbreaker for controlled chips Delivering consistent chip control and steady cutting performance The DNGG110404M-MN3 WN10 insert is engineered to combine a robust cutting geometry with predictable chip formation. The combination of an uncoated carbide grade and an MN3 chipbreaker supports reliable chip breaking and evacuation, reducing the risk of tangled chips in semi-continuous turning. The 0.4 mm corner radius contributes to a stable cutting edge that tolerates moderate variations in feed and depth of cut, while the rhombic 55° shape allows for versatile clamping options and good access to workpiece contours. These technical choices translate into fewer process interruptions and a more consistent surface finish on turned components. Practical application guidance and process reliability For general turning tasks where a resilient edge and repeatable chip control are priorities, this insert offers a practical solution. The negative 0° rake provides a robust contact geometry suited to interrupted cuts and heavier engagement compared with positive-rake alternatives. Material suitability should be confirmed using the manufacturer's product matrix; the insert's grade is intended as an uncoated carbide option and may be selected where its balance of edge strength and economy matches the operation. If there is uncertainty about compatibility with a specific workpiece material or machining strategy, technical advice is available at info@metav-werkzeuge.com or by phone at +49 2822 7131930. Ease of specification, mounting and reliable origin Specification and ordering are straightforward thanks to the clear ISO designation and compact geometry: the insert is presented in the standard DNGG form factor with thickness code 04 and size 11, tolerance class G. The rhombic geometry supports commonly used toolholders for indexable turning inserts, enabling quick changeover and simple inventory management. Backed by Walter Tools, a recognised name in precision tooling and part of the broader industry group, the insert benefits from manufacturer traceability and consistent production quality, supporting process reproducibility on the shopfloor Contact Metav Werkzeuge to confirm the DNGG110404M-MN3 WN10 suitability for specific materials or to place an order; technical consultants are available at +49 2822 7131930 or info@metav-werkzeuge.com Technical Data Article number: DNGG110404M-MN3-WN10-WALTER Designation: DNGG110404M-MN3 WN10 Product type: Turning insert (indexable insert) Facts Corner radius: 0.4 mm Free cutting angle: 0° (negative) Thickness code: 04 Insert size: 11 Tolerance class: G Special features Carbide grade: uncoated (WN10) Chipbreaker: MN3 Shape: Rhombic 55° Series: Walter carbide grade series – open series Execution: G Material specification: catalogue-dependent FAQ What materials is this insert suitable for? Material suitability should be checked in the manufacturer's product matrix; the DNGG110404M-MN3 WN10 is an uncoated carbide grade intended for a broad range of turning tasks, but selection must be confirmed against workpiece material and machining conditions. How does the MN3 chipbreaker influence chip behaviour? The MN3 chipbreaker is designed to produce short, controllable chips in many turning operations, improving evacuation and reducing the risk of chip entanglement when using the DNGG110404M-MN3 WN10 insert. Which holder types accept a rhombic 55° insert? Standard toolholders for rhombic DNGG-style inserts accommodate this geometry; clamping and insert seating should follow the toolholder manufacturer's specifications to ensure secure fixation and repeatable tool setting with the DNGG110404M-MN3 WN10. What effect does the negative 0° rake have on machining? A negative 0° rake delivers a more robust cutting edge that can handle interrupted cuts and heavier engagement more reliably than positive-rake variants, helping to protect the edge under demanding conditions when using this insert. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanatory purposes only; there is no connection between Metav Werkzeuge and the mentioned brands. The offered item is an original, factory-new product of the manufacturer.
DNGG110404M-MN3 WNN10 Wendeplatten - Walter Tools
Optimise turning operations with the combination of coated carbide WNN10 and the MN3 chipbreaker for reliable chip control and consistent surface quality; the insert’s Rhombus 55° geometry and 0.4 mm corner radius support repeatable edge life. Order the DNGG110404M-MN3 WNN10 directly via Metav Werkzeuge or ask the consultants for specification support. DNGG110404M-MN3 WNN10 — Turning indexable insert by Walter Tools, Rhombus 55° & MN3 The DNGG110404M-MN3 WNN10 is a rhombic turning insert intended for precision lathe operations where predictable chip formation and robust edge behaviour are required Rhombic 55° geometry for stable cutting 0.4 mm corner radius for consistent edge life Coated carbide grade WNN10 for wear resistance MN3 chipbreaker for controlled chip formation Predictable geometry for consistent component finish The rhombic 55° geometry provides a reliable cutting angle that supports stable engagement and predictable tool forces. Combined with a 0.4 mm corner radius, the geometry helps to distribute cutting stresses and reduce the risk of premature edge chipping, which in turn contributes to a consistent surface finish on the turned workpiece. The negative free angle of 0° (negative) increases edge strength for heavier cuts; this arrangement is particularly useful when robustness and repeatability are priorities in serial production. Controlled chip formation and wear performance Equipped with the MN3 chipbreaker, the insert promotes reliable chip control across a range of turning conditions, reducing the incidence of long, entangling chips and improving process safety. The cutting material is a coated carbide in grade WNN10, which provides wear resistance and thermal stability during continuous cutting. Note that the grade’s suitability for specific workpiece materials should be verified against the manufacturer’s product matrix to ensure optimal performance and tool life. Practical benefits for workshop integration The DNGG110404M-MN3 WNN10 is supplied in a standard insert designation that simplifies toolholder selection and stocking. With a size code of 11 and thickness code 04, it fits conventional clamping systems used in turning operations, while the tolerance class G assures consistent fit and repeatability. These attributes reduce setup time and support steady production throughput. For applications requiring material-specific advice, the product matrix or Metav Werkzeuge’s technical consultants can clarify optimal cutting parameters and grade selection. For application advice or order placement, contact Metav Werkzeuge – they can assist with grade recommendations and compatibility checks for workshop conditions Technical data Article number: DNGG110404M-MN3-WNN10-WALTER Designation: DNGG110404M-MN3 WNN10 Manufacturer: Walter Tools Product type: Turning indexable insert Series: Walter Schneidstoffsorte - Serie offen Insert size: 11 Thickness code: 04 Corner radius: 0.4 mm Free angle: 0° (negative) Tolerance class: G Geometry: Rhombus 55° Chipbreaker: MN3 Carbide type: Coated carbide (WNN10) Execution: G Identification: DNGG110404M-MN3 FAQ What is the main advantage of the MN3 chipbreaker? The MN3 chipbreaker on the DNGG110404M-MN3 WNN10 produces short, controllable chips, improving process safety and reducing the need for chip handling during turning operations. Is the WNN10 grade suitable for all materials? WNN10 is a coated carbide grade; its application range should be confirmed via the manufacturer’s product matrix to ensure compatibility with the intended workpiece material and cutting conditions. How does the 0.4 mm corner radius affect performance? A corner radius of 0.4 mm increases edge strength and contributes to a consistent surface finish; it is well suited for general turning where a balance between strength and form accuracy is required. Can this insert be used in standard toolholders? Yes, the DNGG110404M-MN3 WNN10 follows a standard insert designation and is compatible with common turning toolholders designed for rhombic 55° inserts. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DNGG150402-MS3 WSM01 Wendeplatten - Walter Tools
Benefit from the combination of the Tiger‑tec Silver coating and the WSM01 grade for reliable machining of stainless steel and heat‑resistant superalloys; the MS3 chipbreaker and rhombic 55° geometry provide secure chip control and extended edge life — order this solution via Metav Werkzeuge or consult our specialists for the best application setup. DNGG150402-MS3 WSM01 indexable turning insert – Tiger‑tec Silver for stainless steel and superalloys (Walter Tools) A DNGG150402-MS3 WSM01 indexable turning insert engineered for demanding turning operations on stainless steel and high‑temperature alloys, offering robust edge stability and consistent chip formation. Coated Tiger‑tec Silver grade WSM01 For stainless steels and superalloys Rhombic 55° geometry, 0.2 mm corner radius MS3 chipbreaker for reliable chip control Consistent cutting performance where heat and work hardening matter The coated Tiger‑tec Silver grade WSM01 is designed for applications that stress the cutting edge: stainless steel and heat‑resistant superalloys. The coating and carbide substrate combine to improve heat resistance and reduce adhesive wear, which results in more stable cutting conditions and fewer interruptions for edge dressing. In practice, this leads to a measurable improvement in process reliability and repeatability when machining tough materials that tend to work‑harden or form built‑up edge. Geometry that gives predictable results and safe handling A rhombic 55° form with a 0° (negative) free angle and a 0.2 mm corner radius provides a balance between cutting strength and surface finish. The 55° approach angle lowers radial cutting forces and helps maintain dimensional accuracy on slender workpieces, while the modest corner radius supports a reproducible edge for longer intervals. The insert thickness code and inscribed size are chosen for standard DNGG toolholders, ensuring straightforward integration into existing turning setups. Controlled chips and higher process security The MS3 chipbreaker is optimised for secure chip segmentation in demanding alloys, reducing the risk of long stringy swarf and improving evacuation from the cutting zone. Secure chip control reduces machine downtime and the need for manual intervention, contributing to increased throughput. Where coolant strategies are used, the chip geometry helps to direct coolant to the cutting edge, supporting temperature management and extending effective edge life. Practical scope and workshop integration for everyday production This turning insert is suited to users seeking reliable, repeatable results in production turning of stainless steel and temperature‑resistant materials. It is compatible with standard negative‑rake DNGG toolholders and is intended for shops that prioritise process stability and low variation between batches. Tool change and indexation are straightforward, and the insert’s specification supports both roughing and semi‑finishing operations depending on parameter choice. Contact Metav Werkzeuge for application advice on integrating the Tiger‑tec Silver WSM01 insert into production lines and to request tailored cutting data for specific stainless steel grades Technical data Article number: DNGG150402-MS3-WSM01-WALTER ISO designation: DNGG150402-MS3 WSM01 Manufacturer: Walter Tools Facts Plate form: Rhombus 55° Corner radius: 0.2 mm Free angle: 0° (negative) Plate size: 15 mm Plate thickness code: 04 Tolerance class: G Special features Series: Tiger‑tec Silver Grade: WSM01 (coated carbide) Chipbreaker: MS3 Material suitability: S / M (stainless steel, superalloys) FAQ What materials is this insert suitable for? The DNGG150402-MS3 WSM01 is formulated for machining stainless steel and heat‑resistant superalloys (grade S/M); the WSM01 grade supports secure chip formation and edge stability in these groups. How does the MS3 chipbreaker affect machining? The MS3 chipbreaker on this insert promotes controlled chip segmentation, reducing swarf issues and improving process security during continuous or interrupted cuts. Is the geometry compatible with standard negative‑rake toolholders? Yes. The DNGG150402‑MS3 form is intended for negative‑rake DNGG toolholders and can be indexed or replaced according to standard turning tool procedures. What advantages does the Tiger‑tec Silver coating provide? The Tiger‑tec Silver coating enhances heat resistance and reduces adhesive wear on the cutting edge, which contributes to longer tool life and more consistent surface quality when machining demanding alloys. Hersteller: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen
DNGG150404-MS3 WSM01 Wendeplatten - Walter Tools
Take advantage of the proven combination of Tiger‑tec Silver wear resistance, the WSM01 grade for stainless and superalloy machining, and the MS3 chipbreaker for stable chip control to maintain productive turning operations; order directly from Metav Werkzeuge or consult our specialists for application advice DNGG150404-MS3 WSM01 indexable turning insert – Rhombic 55°, 0° negative, Tiger‑tec Silver (Walter Tools) The DNGG150404-MS3 WSM01 is an indexable turning insert designed for secure chip control and reliable machining of stainless steels and heat‑resistant superalloys in demanding turning applications Tiger‑tec Silver coating for wear resistance WSM01 grade optimised for stainless steel and superalloys MS3 chipbreaker for secure chip control Rhombic 55° shape with 0.4 mm corner radius Consistent performance in stainless and heat‑resistant materials The coated WSM01 grade from the Tiger‑tec Silver family is formulated for the specific challenges of machining rostfreier Stahl (stainless steel) and heat‑resistant superalloys or titanium. Its combination of a wear‑resistant coating and a robust substrate promotes stable cutting edges and reduces the risk of built‑up edge, which in turn supports longer tool life and fewer insert changes. For production environments where repeatability matters, this geometry and material pairing yields reliable surface quality and process stability. Geometry and chip control that improves cycle times A rhombic 55° profile with a 0° negative rake provides rigidity and predictable cutting forces in turning operations, while the MS3 chipbreaker manages chip formation for both continuous and moderately discontinuous cuts. The modest corner radius of 0.4 mm balances edge strength and surface finish, helping to avoid premature chipping on interrupted cuts and to maintain acceptable part tolerances. These design choices translate into fewer machining interruptions and improved overall throughput. Practical benefits for the workshop floor Using this indexable insert supports efficient production by reducing unplanned downtime: the stable wear behaviour of the Tiger‑tec Silver coating extends effective tool life, and the MS3 chipbreaker lowers the risk of snarled chips in lathes and multi‑spindle machines. The insert is particularly suited to applications where heat generation and material toughness challenge conventional grades; adopting the insert can therefore contribute to lower tooling cost per part and higher first‑pass quality. Selection and integration guidance When integrating the insert into an existing toolholder, ensure proper seat contact and correct clamping torque to preserve the intended cutting geometry. Given the insert’s focus on stainless and high‑temperature alloys, pairing it with a rigid holder and appropriate cutting parameters helps exploit the WSM01 sort’s advantages. For users seeking further optimisation—cutting data, coolant strategy or holder recommendations—technical consultation is available to adapt parameters to specific machine and workpiece conditions. For demanding stainless steel and superalloy turning, request Walter Tools’ Tiger‑tec Silver inserts via Metav Werkzeuge for fast availability and tailored machining advice; contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: DNGG150404-MS3-WSM01-WALTER Product: indexable turning insert Brand: Walter Tools Series: Tiger‑tec Silver Grade: WSM01 Facts Shape: rhombic 55° Relief angle: 0° negative Corner radius: 0.4 mm Insert size: 15 Plate thickness code: 04 Tolerance class: G Special features Chipbreaker: MS3 Coating: Tiger‑tec Silver Material compatibility: S / M (superalloys/titanium, stainless steel) Execution: G FAQ What materials is the insert suitable for? The insert is intended for machining rostfreier Stahl (stainless steel) and heat‑resistant superalloys/titanium as specified for the WSM01 grade. How does the MS3 chipbreaker affect machining? The MS3 chipbreaker promotes secure chip control and safer evacuation in turning operations, improving process reliability for the WSM01 insert. Is the Tiger‑tec Silver coating beneficial for tool life? Yes, the Tiger‑tec Silver coating increases wear resistance and contributes to longer effective tool life under the thermal and mechanical loads typical of stainless and superalloy turning. Which insert geometry suits short‑chipping vs long‑chipping materials? The rhombic 55° geometry with a 0° negative rake and 0.4 mm corner radius offers a compromise that performs well in tougher, short‑chipping materials while maintaining edge strength for interrupted cuts. Manufacturer: Walter Tools; Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and brand names are the property of their respective owners. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DNGG150404M-MN3 WNN10 Wendeplatten - Walter Tools
Benefit from the combination of coated carbide durability, MN3 chip control and rhombic 55° geometry for consistent, productive turning results; order the insert directly via Metav Werkzeuge or consult our specialists for application guidance. DNGG150404M-MN3 WNN10 turning indexable insert by Walter Tools — rhombic 55° geometry, MN3 chipbreaker A DNGG150404M-MN3 WNN10 is a rhombic 55° turning insert designed for general turning operations where robust cutting, predictable chip control and repeatable performance are required. Rhombic 55° geometry for versatile turning Coated carbide grade WNN10 for broad use Zero-degree negative rake for robust cutting MN3 chipbreaker with 0.4 mm corner radius Durable geometry that increases process stability The rhombic 55° geometry combined with a 0° (negative) rake delivers a stable cutting angle that reduces insert breakouts and supports dependable tool life under varying cutting conditions. This geometry provides a compromise between reach and strength, permitting secure clamping and reliable entry into the cut; the result is improved process stability and fewer interruptions on production runs. For workshops needing consistent productivity, the insert’s form reduces the risk of chatter and helps maintain surface finish over longer cycles. Coated carbide grade built for broad applications The WNN10 designation signifies a coated carbide grade tailored for general-purpose turning. The coating enhances wear resistance and contributes to sustained cutting performance on a range of workpiece materials, while the substrate supports edge stability. Material suitability should be confirmed against the manufacturer’s product matrix before use; this ensures the chosen grade matches the specific steels or alloys in a given application. Proper selection leads to lower tooling costs per part through longer intervals between indexings. Controlled chip formation for safer machining The MN3 chipbreaker has been developed to shape and evacuate chips effectively in routine turning tasks, reducing the risk of entanglement and improving surface integrity. Together with a 0.4 mm corner radius, the chip control strategy softens the cutting impact at the edge, which can reduce micro-chipping and contribute to a steadier surface quality. This configuration is particularly beneficial in serial production where repeatability and minimal rework are priorities. Practical fit, handling and insertion benefits The insert follows standard dimensions with a nominal size 15 and thickness code 04, enabling compatibility with common tool holders for rhombic 55° inserts. The naming convention and ISO-style designation simplify procurement and inventory management, while the robust format supports straightforward indexing for multi-edge use. For users planning toolholder selection or inventory stocking, the clear ISO-style label and chipbreaker type ease identification and reduce the time spent matching inserts to holders. For application advice specific to Walter Tools inserts or to secure the DNGG150404M-MN3 WNN10 for production use, contact Metav Werkzeuge GmbH at info@metav-werkzeuge.com or call +49 2822 7131930 to speak with a consultant who can recommend the optimal grade and geometry for the task at hand. Technical data Article number: DNGG150404M-MN3-WNN10-WALTER Designation: DNGG150404M-MN3 WNN10 Product type: Drehwendeschneidplatte / Turning indexable insert Manufacturer: Walter Tools Execution: G Facts Free angle: 0° (negative) Corner radius: 0.4 mm Plate form: Rhombus 55° Plate size: 15 Plate thickness: 04 Tolerance class: G Special features Chipbreaker: MN3 Grade/series: WNN10; Walter coated carbide Series description: Walter Schneidstoffsorte - Serie offen Material note: catalogue dependent ISO designation: DNGG150404M-MN3 WNN10 FAQ What cutting geometry does this insert use? The insert features a rhombic 55° geometry with a 0° (negative) rake, offering a robust angle for general turning operations and reliable edge engagement. Which chipbreaker and corner radius are specified? This indexable insert uses the MN3 chipbreaker and a 0.4 mm corner radius, optimised for controlled chip formation and improved edge stability during routine turning. Is the WNN10 grade suitable for all materials? The WNN10 coated carbide grade is intended for broad use, but material suitability should be checked against the manufacturer’s product matrix to ensure optimal performance on the intended workpiece materials. How does the negative rake affect cutting performance? A negative rake increases edge strength and resistance to mechanical stress, making the insert suitable for heavier cuts and interrupted cuts where robustness is required. How is the insert identified for procurement and inventory? Identification follows the ISO-style designation DNGG150404M-MN3 WNN10, which aligns with common ordering and stocking practices for turning inserts. Protected trademarks and trade names remain the property of their respective owners. Brand names and registered marks are mentioned for explanatory purposes only. There is no affiliation between our company and the mentioned brands. The offered item is original, brand-new goods from the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
DNGG150408-MS3 WSM01 Wendeplatten - Walter Tools
Take advantage of the combination of a Tiger‑tec Silver carbide grade and the WSM01 geometry for reliable machining of demanding materials; robust edge stability and the MS3 chipbreaker reduce tool changes and support consistent production. Order directly via Metav Werkzeuge or consult our technical advisors for application-specific recommendations. DNGG150408-MS3 WSM01 indexable turning insert — Tiger‑tec Silver, Rhombic 55° by Walter Tools A DNGG150408-MS3 WSM01 indexable turning insert designed for heavy‑duty turning of rostfreier Stahl and heat‑resistant superalloys, offering a sturdy edge and controlled chip formation for stable machining results Tiger‑tec Silver grade WSM01 Optimised chip control with MS3 Rhombic 55° geometry for stable cutting 0.8 mm corner radius for robust edges Consistent performance in demanding materials The WSM01 grade, part of Tiger‑tec Silver, combines a coated carbide matrix with a geometry that promotes stable cutting when machining rostfreier Stahl and high‑temperature alloys. The coating enhances wear resistance and thermal stability, which translates into fewer interruptions for tool changes and a more predictable tool life. For production environments where repeatability and surface quality matter, this indexable solution reduces scrap rates and supports tight tolerances through consistent edge behaviour. Geometry and chip control for secure turning The rhombic 55° profile and the MS3 chipbreaker are designed to harmonise cutting forces and chip flow. The insert’s 0.8 mm corner radius and negative 0° rake contribute to a robust cutting edge that withstands interrupted cuts and higher feed demands. The chipbreaker promotes short, controllable chips in materials that tend to produce long, stringy swarf, improving machining safety and avoiding rework related to poor chip evacuation. Productivity and economical advantages With its combination of coated carbide technology and a purpose‑built chipformer, this insert minimises flank and crater wear under challenging cutting conditions. Reduced wear stabilises cycle times and lowers tooling costs per workpiece. In mixed‑batch production where rostfrei and nickel‑based components appear together, the WSM01 grade enables a balanced compromise between edge life and cutting performance, supporting efficient workflows and fewer tool‑change stoppages. Selection advice and typical use cases The insert is optimised for turning operations where material toughness and heat generation are limiting factors—particularly stainless alloys and superalloys. Use the rhombic 55° geometry for external turning and profiling tasks that require a combination of access and edge strength. The MS3 chip control works well across a range of feeds; pairing the insert with appropriate coolant strategies and stable clamping will maximise the service life of the cutting edge. Choose the Walter Tools Tiger‑tec Silver DNGG150408‑MS3 WSM01 insert for robust turning of rostfreier Stahl and superalloys; contact Metav Werkzeuge for tailored application advice and ordering at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: DNGG150408-MS3-WSM01-WALTER Article: Drehwendeschneidplatte DNGG150408-MS3 WSM01 Walter Tools Manufacturer: Walter Tools Facts Plate form: Rhombus 55° Size: 15 mm Corner radius: 0.8 mm Thickness code: 04 Relief angle: 0° (negative) Chipbreaker: MS3 Tolerance class: G Special features Series: Tiger‑tec Silver Grade: WSM01 (coated carbide) Material application: S / M (rostfreier Stahl; heat‑resistant superalloys) Robust edge geometry for heavy cuts FAQ Which materials is this insert intended for? The DNGG150408‑MS3 WSM01 insert is intended primarily for rostfreier Stahl and heat‑resistant superalloys (ISO groups M and S), providing secure chip control and edge stability in these materials. What role does the MS3 chipbreaker play? The MS3 chipbreaker on this grade controls chip formation to produce short, manageable chips, improving evacuation and reducing the risk of surface damage during turning operations. How does the Rhombic 55° shape affect machining? The rhombic 55° profile offers a balance between approach angle and edge strength, suitable for external turning and profiling where access and robust cutting performance are required. Is the WSM01 grade coated, and what benefit does the coating provide? Yes, WSM01 is a coated carbide grade within the Tiger‑tec Silver family; the coating increases thermal and wear resistance, extending edge life under challenging cutting conditions. Protected trademarks and trade names are the property of their respective owners. Brand names are used for explanation only and indicate no affiliation between our company and the named manufacturers; the offered article is an original, brand‑new product of the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen
DNGG150408M-MN3 WNN10 Wendeplatten - Walter Tools
Take advantage of the combination of coated carbide grade WNN10, MN3 chipbreaker and robust rhombic geometry for steady chip control and predictable tool life; order directly via Metav Werkzeuge or consult our specialists for application advice. DNGG150408M-MN3 WNN10 indexable turning insert — Rhombic 55°, 0.8 mm corner radius (Walter Tools) The DNGG150408M-MN3 WNN10 is a coated cemented-carbide indexable turning insert engineered for stable roughing and semi-finishing operations where consistent chip formation and reliable edge life are required. Coated carbide grade WNN10 Rhombic 55° geometry for flexible cutting Negative rake 0° for robust cutting Corner radius 0.8 mm for strength Consistent chip control that keeps production running The insert’s combination of the WNN10 coated carbide grade and the MN3 chipbreaker delivers predictable chip formation and evacuation, reducing interruptions caused by chip jams. The chipbreaker is tuned to moderate cutting depths and feeds, so the machining process benefits from fewer manual interventions and more stable cycle times. Explaining the technical side: a chipbreaker redistributes cutting forces and breaks chips into manageable lengths, which in turn lowers the risk of surface damage and tool overload. For manufacturers seeking higher line throughput, this translates into measurable process reliability and lower rework rates. Geometry built for strength and adaptable turning strategies A rhombic 55° insert offers a versatile approach to turning: the angle supports both general-purpose cutting and challenging interrupted cuts, while the 0° negative rake increases edge robustness under heavy engagement. The 0.8 mm corner radius gives the cutting edge additional resistance to chipping, which is particularly advantageous when roughing or handling variable stock conditions. In practice, this geometry enables operators to maintain higher metal removal rates with less concern for premature edge failure, improving uptime and tool-change predictability. Coating and grade designed for stable tool life The grade is a coated cemented carbide formulation that balances wear resistance and toughness, aiming to extend usable edge life across a range of operations. Coatings reduce flank and crater wear by acting as a thermal and chemical barrier at the cutting zone; paired with a carbide substrate, they preserve cutting-edge integrity under continuous loading. When process stability is the priority, a coated grade such as this helps maintain dimensional consistency across batches and contributes to a lower cost per component over the life of the insert. Application guidance and integration into production This insert is supplied as the DNGG150408M-MN3 WNN10 variant and is manufactured to tolerance class G. For correct material pairing and cutting-data optimisation, consult the Walter product matrix and machining recommendations; material suitability should be verified against specific workpiece alloys and hardness levels. The insert’s form factor and chipbreaker make it suitable for conventional turning set-ups and many CNC lathes; integration is straightforward when the toolholder matches the DNGG15 insert profile. For tailored cutting parameters or to confirm compatibility with a particular turning strategy, Metav Werkzeuge’s technical advisors can provide detailed recommendations. Contact Metav Werkzeuge for tailored machining data or to request the Walter Tools DNGG150408M-MN3 WNN10 insert and receive specialist advice by phone or email: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: DNGG150408M-MN3-WNN10-WALTER Product type: indexable turning insert Designation: DNGG150408M-MN3 WNN10 Facts Size: 15 Thickness: 04 Corner radius: 0.8 mm Geometry angle: 55° Free rake angle: 0° (negative) Tolerance class: G Special features Grade: WNN10 (coated cemented carbide) Chipbreaker: MN3 Plate form: Rhombus 55° Series: Walter Schneidstoffsorte - Serie offen Execution: G FAQ What chip control advantages does the MN3 chipbreaker provide? The MN3 chipbreaker on the DNGG150408M-MN3 WNN10 insert promotes shorter, controllable chips and reduces the risk of entanglement, improving process reliability in turning operations. Is the insert suitable for heavy roughing or only finishing cuts? Thanks to the negative rake and 0.8 mm corner radius, this Walter Tools insert is designed for robust cutting and is well suited to heavy roughing as well as semi-finishing, depending on cutting data and holder rigidity. How should the coated grade WNN10 be selected against other grades? Select WNN10 for applications where a balance of wear resistance and toughness is required; consult the Walter product matrix for direct comparisons and recommended cutting parameters for specific materials. Which toolholder profile is required for this insert? The DNGG150408M-MN3 insert fits standard holders designed for DNGG15-style rhombic 55° inserts; verifier holder compatibility with the insert designation before mounting. How does the rhombic 55° geometry affect cutting strategy? Rhombic 55° geometry offers a compromise between strength and cutting edge accessibility, enabling flexibility between roughing and finishing passes while maintaining edge resilience. Manufacturer: Walter Tools / Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
DNGG150604-NFT WS10 WS10 Wendeplatten - Walter Tools
Take advantage of the WS10 grade and the NFT chipbreaker to achieve stable chip control and consistent tool life; the rhombic 55° geometry and 0.4 mm corner radius support fine surface finishes and precise turning operations. Order the insert directly via Metav Werkzeuge or consult their specialists for application-specific advice. DNGG150604-NFT WS10 – Rhombic 55° turning insert with NFT chipbreaker | Walter Tools The DNGG150604-NFT WS10 is a rhombic 55° turning indexable insert designed for robust external turning, combining a coated carbide grade with an NFT chipbreaker for controlled swarf evacuation. Rhombic 55° geometry for versatile turning Negative 0° rake for stable cutting forces Coated carbide WS10 for broad application range 0.4 mm corner radius for improved surface finish Reliable chip control that keeps cycles running The rhombic 55° geometry together with the NFT chipbreaker delivers consistent chip formation and evacuation under varying cutting conditions. The negative 0° rake stabilises the cutting edge, reducing vibration and allowing deeper cuts with predictable tool behaviour. For production environments where cycle time and repeatability matter, these design elements translate into fewer interruptions for manual chip removal and more time at productive cutting speeds. The WS10 grade, a coated carbide option, supports a wide range of materials (see technical data) and is optimised for general turning tasks that demand steady performance. Precision finish and dimensional stability for repeatable parts With a 0.4 mm corner radius and the rhombic profile, the insert promotes improved surface quality and dimensional consistency on turned components. The profile reduces chatter on thin-walled and interrupted cuts, which helps maintain tolerance across batches. The standard size designation 15 and thickness 06 ensure compatibility with common clamping systems; the insert’s profile and edge form mean fewer passes are necessary to reach final dimensions, saving machine time and reducing secondary finishing. Bold emphasis on tool geometry and edge control supports dependable, repeatable results in serial production. Practical application guidance and compatibility This insert is delivered as part of the Walter Schneidstoffsorte – Serie offen and is specified under the designation DNGG150604-NFT WS10. The material specification is catalogue-dependent; users should verify the exact coating and substrate variant in the current Walter documentation for best results. The insert’s tolerance class G and G execution indicate standardised manufacturing accuracy suited to general turning tasks. For integration into existing toolholders, match the rhombic 55° seat and confirm the clamping system accepts designation 15 inserts. When machining variable materials, check the product matrix to select the optimum cutting parameters for surface finish and tool life. Contact Metav Werkzeuge today for tailored machining parameters, application compatibility checks and to request a quotation for the DNGG150604-NFT WS10 from Walter Tools Technical Data SKU: DNGG150604-NFT-WS10-WALTER Name: DNGG150604-NFT WS10 Product type: Turning indexable insert / Drehwendeschneidplatte Manufacturer: Walter Tools Series: Walter Schneidstoffsorte - Serie offen Grade: WS10 Core technical data Plate form: Rhombus 55° Size designation: 15 Thickness: 06 Corner radius: 0.4 mm Rake: 0° (negative) Chipbreaker: NFT Tolerance class: G Execution: G Special features and materials Coating/substrate: coated carbide (catalogue-dependent) Application note: Verify material suitability in product matrix Design goal: stable chip formation and productive turning Intended use: external turning with controlled chip evacuation FAQ What materials is this insert suitable for? The DNGG150604-NFT WS10 is a coated carbide insert; material suitability should be checked in the Walter product matrix to select the correct variant for specific steels, non-ferrous metals or other workpiece materials. How does the NFT chipbreaker affect machining? The NFT chipbreaker on the DNGG150604-NFT WS10 promotes predictable chip shapes and efficient evacuation, reducing the risk of chip jamming and improving process stability during turning. Can this insert be used in interrupted cuts? Yes, the rhombic 55° geometry and the negative 0° rake of this Walter Tools insert are designed to withstand intermittent engagements and to reduce vibration in interrupted turning. What does the size designation '15' and thickness '06' mean for clamping? The size designation 15 and thickness 06 are standard insert identifiers; they indicate the seat and clamp compatibility—confirm the toolholder matches these designations for safe clamping. Is the WS10 grade suitable for high-speed machining? WS10 is a coated carbide grade intended for broad application; consult Walter’s technical data for cutting speed recommendations and the exact coated variant available in the catalogue. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only and do not imply any affiliation between our company and the brands named. The item offered is original, factory-new merchandise from the manufacturer.
DNGG150604M-MN3 WNN10 Wendeplatten - Walter Tools
Take advantage of a robust combination of precise geometry, a coated carbide WNN10 grade and effective chip control to maintain consistent turning performance; order the inserts directly via Metav Werkzeuge or consult the team for application-specific recommendations. DNGG150604M-MN3 WNN10 indexable turning insert — Rhombic 55°, 0° rake — Walter Tools A DNGG150604M-MN3 WNN10 indexable insert engineered for conventional and semi-finish turning where stable chip formation and predictable corner definition are required Coated carbide grade WNN10 Rhombic 55° insert geometry Negative 0° rake angle MN3 chipbreaker for stable chips Predictable cutting performance for productive turning The combination of a coated carbide grade and a defined MN3 chipbreaker enables stable cutting in a range of operations; the insert’s design reduces unexpected interruptions by promoting controlled chip formation. The negative 0° rake reduces cutting-edge loading at moderate depths of cut, which can extend tool life and improve process reliability. For production environments seeking repeatable results, the geometry supports consistent insert seating and predictable wear patterns. Geometry that balances accessibility and edge strength The rhombic 55° shape offers an advantageous compromise between approach angle and accessibility in tight bores or shoulder work. The relatively small corner radius 0.4 mm helps to achieve finer detail and closer tolerances while maintaining a robust cutting edge for common turning cycles. This geometry is particularly useful where a sharper effective cutting angle is required without sacrificing edge stability, translating into reliable dimensional control and fewer reworks. Practical machining benefits and interpretive guidance The insert thickness (06) and the 15 mm size create a familiar footprint that integrates with standard toolholders; the nominal thickness contributes to vibration damping and edge support. The term “chip control” here refers to the insert’s ability to break and evacuate swarf consistently, which improves surface integrity and reduces the risk of built-up edge. Customers unfamiliar with these terms can regard chip control and rake angle as levers to tune productivity and surface finish in their specific set-ups. Grade and series context for informed selection The WNN10 designation denotes a coated carbide class intended for broad applications; final suitability should be verified against a product-material matrix. The insert belongs to the Walter Schneidstoffsorte series and benefits from modern coating technology that typically enhances wear resistance and process stability. When planning tool cycles, consider matching insert grade and chipbreaker to the machining strategy—this helps to optimise cutting parameters and maintain a consistent production flow. For tailored application advice or to reserve Walter Tools inserts, contact Metav Werkzeuge for fast recommendations and order processing — eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical data Article number: DNGG150604M-MN3-WNN10-WALTER SKU: DNGG150604M-MN3-WNN10-WALTER Label: Drehwendeschneidplatte DNGG150604M-MN3 WNN10 Walter Tools Manufacturer: Walter Tools Product type: Drehwendeschneidplatte Core technical figures Insert size: 15 mm Thickness: 06 Corner radius: 0.4 mm Rake angle: 0° (negative) Insert form: Rhombus 55° Designs and special features Grade: WNN10 (coated carbide) Chipbreaker: MN3 Series: Walter Schneidstoffsorte - Serie offen Execution / tolerance class: G Designation without grade: DNGG150604M-MN3 Full ISO designation: DNGG150604M-MN3 WNN10 FAQ What is the purpose of the MN3 chipbreaker? The MN3 chipbreaker on the DNGG150604M-MN3 WNN10 insert is designed to produce short, controllable chips that are easier to evacuate, improving surface finish and reducing the risk of swarf-related interruptions. How does the negative 0° rake affect machining? A negative 0° rake angle increases edge strength and reduces the tendency for edge chipping under interrupted cuts; in the case of this insert it contributes to stable cutting behaviour during moderate finishing and semi-finishing operations. Why is the 0.4 mm corner radius important? The 0.4 mm corner radius balances surface quality and edge robustness: it enables fine detail and dimensional control while maintaining sufficient edge strength for repeated use. When is a rhombic 55° insert chosen over other geometries? The rhombic 55° form is selected when access geometry or approach angle requires a compact effective cutting edge; it is beneficial for shoulder work and operations where an acute approach angle improves chip flow. How should the WNN10 grade be matched to materials? WNN10 is a coated carbide grade intended for broad applications; however, final selection should be based on the specific product-material matrix to ensure optimal wear behaviour and process stability. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools), headquartered in Tübingen, is among the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trade designations are cited for explanation only. There is no affiliation between our company and the mentioned brands. The offered article is an original, factory-new product of the manufacturer.
DNGG150608-NFT WS10 WS10 Wendeplatten - Walter Tools
Combining the WS10 coated‑carbide grade with the NFT chipbreaker and a rhombic 55° geometry yields stable chip formation and dependable edge life for medium to heavy turning operations; order the insert via Metav Werkzeuge or request application advice for specific material matrices. DNGG150608-NFT WS10 — Walter Tools turning insert with NFT chipbreaker and 0° negative rake DNGG150608-NFT WS10 is a rhombic 55° turning insert designed for general turning tasks where consistent chip control and predictable tool life are required. Coated carbide grade WS10 for general machining Rhombic 55° insert geometry for flexible turning NFT chipbreaker for controlled chip formation Negative rake 0° for robust cutting edge Predictable performance from a coated carbide grade The WS10 grade is a coated carbide variant developed for broad applicability across common turning tasks. Its coating supports heat resistance and wear protection, which translates into longer tool life and fewer interruptions for insert changes. In practice, the coated surface reduces flank wear under steady cutting conditions, so operators benefit from consistent dimensional accuracy over longer runs. The combination of a wear‑resistant grade and an engineered coating means predictable productivity in mixed production environments. Stable chip control through the NFT chipbreaker The integrated NFT chipbreaker is engineered to produce short, controllable chips across a range of cutting parameters. Good chip control minimises rework and reduces the risk of tool or workpiece damage, improving operator safety and downstream handling. For machinists working with interrupted cuts or variable feed rates, the chipbreaker design reduces the need for manual chip clearing and helps maintain steady cycle times—an operational advantage that converts directly into higher throughput. Geometry and mechanical robustness for demanding turning The rhombic 55° form combined with a negative rake of 0° delivers a robust cutting edge suited to heavier cuts and interrupted work. The insert’s corner radius 0.8 promotes a balance between edge strength and surface finish: a larger radius increases edge stability, while the 0.8 value maintains acceptable surface quality on many components. Mechanically, the insert body and geometry are designed to withstand the forces of conventional turning, making it suitable for batch production and mixed‑complexity shops that require repeatable results. Application guidance and process reliability This insert is supplied in the Walter Tools open series and should be selected according to the specific material matrix of the workpiece. The WS10 grade and NFT chipbreaker provide a good starting point for common steels and general turning tasks, but process optimisation—feed, speed and depth of cut—should be adjusted for each application to achieve the best economy. For shops seeking reduced tool change frequency and stable surface finishes, this combination supports a cost‑effective machining strategy while keeping setup complexity low. For reliable production and application support with Walter Tools inserts, contact Metav Werkzeuge for tailored advice at info@metav-werkzeuge.com or via +49 2822 7131930 Technical data Article number: DNGG150608-NFT-WS10-WALTER SKU: DNGG150608-NFT-WS10-WALTER Designation: DNGG150608-NFT ISO designation: DNGG150608-NFT WS10 Manufacturer: Walter Tools Facts Size: 15 Thickness: 06 Corner radius: 0.8 Rake angle: 0° (negative) Tolerance class: G Special features Coated carbide grade WS10 NFT chipbreaker Rhombic 55° plate form Series: Walter Schneidstoffsorte - Serie offen Execution: G Catalogue‑dependent material information FAQ What materials is this insert suitable for? The DNGG150608‑NFT WS10 is a coated‑carbide insert from Walter Tools intended for general turning; the exact workpiece suitability should be checked against the product matrix for WS10. How does the NFT chipbreaker improve production? The NFT chipbreaker on this turning insert promotes short, controlled chips, reducing interruptions for chip removal and supporting steadier cycle times in batch production. What does a 0° negative rake mean for cutting behaviour? A 0° negative rake on the insert provides a robust cutting edge that resists chipping under heavier cuts or interrupted cuts, helping to maintain consistent tool life and dimensional stability. Can this insert be used for finishing passes? With its rhombic 55° geometry and 0.8 corner radius, the insert balances edge strength and finish capability; lighter feeds and speeds improve surface finish when used for finishing operations. Is the WS10 grade coated or uncoated? WS10 is specified as a coated carbide grade in the Walter Tools series, offering enhanced wear resistance compared with uncoated grades. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Die Walter AG (Markenauftritt: Walter Tools) mit Hauptsitz in Tübingen gehört zu den weltweit führenden Herstellern von Präzisionswerkzeugen für die Metallbearbeitung und ist Teil des schwedischen Sandvik‑Konzerns. Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DNGG150608M-MN3 WNN10 Wendeplatten - Walter Tools
Take advantage of the combination of repeatable edge stability, controlled chip formation and a compact Rhombic 55° geometry for efficient turning cycles; order the DNGG150608M-MN3 WNN10 indexable turning insert directly via Metav Werkzeuge or consult our technical advisors for application support. DNGG150608M-MN3 WNN10 indexable turning insert, Rhombic 55° | Walter Tools A robust DNGG150608M-MN3 WNN10 indexable turning insert engineered for medium-duty external turning, featuring a Rhombic 55° geometry and an MN3 chipbreaker for stable chip control Rhombic 55° geometry for versatile turning MN3 chipbreaker for controlled chip formation 0.8 mm corner radius for reliable edge strength Stable cutting performance through optimised edge geometry The insert’s Rhombic 55° shape and 0.8 mm corner radius deliver a balance between edge strength and accessibility, enabling reliable external turning where a robust cutting edge is required. The MN3 chipbreaker is designed to promote short, easily managed chips in interrupted and continuous cuts; this reduces the risk of chip entanglement and contributes to smoother material flow. For production environments, predictable chip behaviour translates directly into shorter cycle times and fewer interruptions, which supports higher machine utilisation and consistent part quality. Coated carbide grade tuned for general turning tasks The Walter WNN10 grade is a coated carbide option intended for a broad range of turning applications; the coating improves wear resistance and supports sustained cutting performance. Coated grades combine a hard substrate with a tailored surface layer to resist abrasion and edge wear, so tool life is generally extended compared with uncoated grades under comparable conditions. Material suitability should be checked against the manufacturer’s product matrix to match the cutting data to the component material and desired surface finish. Negative rake and compact form for dependable machining With a 0° negative rake, the insert is optimised for stable cutting forces and robust engagement with the workpiece, especially when machining with interrupted cuts or tougher materials. A negative rake reduces the likelihood of chipping at the cutting edge and often allows for more conservative fixture and clamping arrangements. The compact format of the insert helps to maintain rigidity in the toolholder assembly, supporting repeatable dimensions and consistent surface integrity across batches. Practical handling and integration into production The insert is supplied in the standard DNGG format and is compatible with corresponding toolholders; mounting is straightforward and indexation enables quick edge changes to minimise downtime. Because the detailed substrate and coating specifics are catalogue-dependent, the item is described as a Walter Schneidstoffsorte series product—please consult the technical data sheet for cutting speeds and feed recommendations tailored to the workpiece material. Proper selection of cutting parameters and coolant strategy will further prolong service life and maintain surface quality. For robust, repeatable turning with Walter Tools’ WNN10 grade, contact Metav Werkzeuge for a tailored recommendation and rapid availability Technical data Article number: DNGG150608M-MN3-WNN10-WALTER SKU: DNGG150608M-MN3-WNN10 Designation: DNGG150608M-MN3 WNN10 Facts Insert shape: Rhombus 55° Corner radius: 0.8 mm Insert size: 15 mm Thickness code: 06 Rake angle: 0° (negative) Special features Chipbreaker: MN3 Grade: WNN10 (coated carbide) Series: Walter Schneidstoffsorte - Serie offen Execution / tolerance class: G Material designation: catalogue-dependent FAQ What materials is this insert suitable for? The DNGG150608M-MN3 WNN10 insert is a coated carbide grade intended for a broad range of turning applications; material suitability should be confirmed in the Walter Tools product matrix for the WNN10 grade. How does the MN3 chipbreaker affect machining? The MN3 chipbreaker on the DNGG150608M-MN3 promotes controlled, short chip formation, improving chip evacuation and reducing the risk of entanglement during medium-duty turning operations. Is the insert compatible with standard DNGG toolholders? Yes, the DNGG150608M-MN3 follows the DNGG indexable insert format and is compatible with corresponding toolholders designed for that form factor. What advantage does the 0° negative rake offer? A 0° negative rake increases edge robustness and stability under load, which is beneficial for interrupted cuts and when machining tougher workpiece materials. Where can cutting data for this insert be found? Cutting parameters and feed recommendations for the DNGG150608M-MN3 WNN10 are provided in the Walter Tools technical documentation and should be used alongside the product matrix to select optimal speeds and feeds. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Trademarks and product names are the property of their respective owners. Mention of brand names is for explanation only and does not imply any affiliation between Metav Werkzeuge and the named manufacturers. The offered item is an original, factory-new product from the stated manufacturer.
DNMA110404-RK5 WKK10S Wendeplatten - Walter Tools
Optimise cast-iron turning with the wear-resistant WKK10S grade and the RK5 chipbreaker: the rhombic 55° geometry and 0.4 mm corner radius deliver stable cutting and consistent surface finish. Order the DNMA110404-RK5 WKK10S turning insert directly via Metav Werkzeuge or consult their specialists for tailored machining advice. DNMA110404-RK5 WKK10S Turning Insert — Tiger·tec Silver for Cast Iron (Walter Tools) A DNMA110404-RK5 WKK10S turning insert engineered for productive cast iron machining, combining Tiger·tec Silver technology and an RK5 chipbreaker for controlled chips. Tiger·tec Silver grade for high wear resistance Optimised RK5 chipbreaker for clean chips Rhombic 55° shape for versatile turning Corner radius 0.4 mm for stable cutting Higher throughput through wear-resistant grade and chip control The combination of the Tiger·tec Silver technology and the WKK10S carbide grade is designed to extend tool life under abrasive conditions typical for cast iron. The coating reduces flank and crater wear, which allows longer uninterrupted production cycles and fewer insert changes. The RK5 chipbreaker shapes short, predictable chips to prevent entanglement and reduce downtime; in practical terms this means higher material removal rates and improved process stability, which together lower unit machining costs and increase overall workshop efficiency. Geometry that stabilises cutting and improves surface finish The rhombic 55° plate form and negative 0° rake angle give mechanical robustness for heavy or interrupted cuts, while the 0.4 mm corner radius balances edge strength with surface quality. Negative rake geometries resist chipping under shock loads, so dimensional accuracy and repeatability are maintained lap after lap. For users unfamiliar with the terms: a corner radius supports the cutting edge against fracture, and a negative rake builds durability — both contribute to consistent part quality and fewer rejects. Practical selection and application guidance for cast iron work Specified for ISO group K (cast iron), the insert is suitable where short, brittle chips and abrasive wear are expected. The plate designation and form make it compatible with standard DNMA-style toolholders, enabling straightforward integration into existing turning setups. Choose appropriate feeds and speeds for the machine rigidity and workpiece grade to exploit the WKK10S advantages: improved tool life and consistent surface finish. For volume production or challenging cast-iron alloys, this insert supports stable cycles and predictable tool-change intervals, helping to plan maintenance windows and throughput. Contact Metav Werkzeuge for machining recommendations, batch availability and assistance in selecting the right Walter Tools turning inserts for specific cast-iron applications Technical data SKU: DNMA110404-RK5-WKK10S-WALTER Designation: DNMA110404-RK5 WKK10S Product type: turning insert Series: Tiger·tec Silver Manufacturer: Walter Tools Facts Plate size: 11 Thickness: 04 Corner radius: 0.4 Plate form: Rhombus 55° Rake angle: 0° (negative) Tolerance class: M Special features Grade: WKK10S Chipbreaker: RK5 Suitable for: cast iron (ISO group K) Execution: A ISO designation: DNMA110404-RK5 WKK10S FAQ Which materials is this insert intended for? The DNMA110404-RK5 WKK10S turning insert is optimised for cast iron (ISO group K) and is designed to cope with the abrasive and short-chip behaviour of such materials. What is special about the WKK10S grade? WKK10S, in the Tiger·tec Silver family, offers enhanced wear resistance and thermal stability for cast-iron turning, which helps to extend tool life and maintain consistent cutting performance. How does the RK5 chipbreaker affect machining? The RK5 chipbreaker produces short, controlled chips that reduce entanglement risk and improve process reliability when using the DNMA110404-RK5 WKK10S insert. Can the insert be used in standard DNMA toolholders? Yes, the DNMA110404-RK5 form matches common DNMA-style holders; verify seat and clamping compatibility before mounting. What cutting conditions are recommended for best results? Moderate to high cutting speeds with stable feed rates and proper coolant strategies are typically effective for cast-iron applications with this grade; adjust parameters based on machine rigidity and workpiece specifics. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand appearance: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanation only. There is no connection between our company and the mentioned brands. The offered item is original, brand-new goods of the manufacturer.
DNMA110408-RK5 WKK10S Wendeplatten - Walter Tools
Take advantage of the combination of a Tiger·tec Silver coated grade and the RK5 chipbreaker to achieve stable chip control and extended tool life in cast iron turning; the rhombic 55° geometry with a 0.8 mm corner radius delivers consistent surface quality and secure insert seating. Order directly via Metav Werkzeuge or consult our technical team for cutting parameters and availability. DNMA110408-RK5 WKK10S — Indexable turning insert for cast iron (Walter Tools) DNMA110408-RK5 WKK10S is an indexable turning insert optimised for productive machining of cast iron components, combining robust geometry with Tiger·tec Silver coating technology Tiger·tec Silver coating for cast iron RK5 chipbreaker for stable chip control Rhombic 55° shape, 0.8 mm corner radius Negative rake 0° for robust turning Longer tool life and predictable performance in cast iron turning The DNMA110408-RK5 WKK10S insert uses a coated carbide grade from the Tiger·tec Silver family, engineered specifically for abrasive cast iron applications. The grade WKK10S balances hardness and toughness to resist abrasive wear common in grey and nodular cast irons, which reduces index changes and machine downtime. As the coating and substrate are matched for this task, the result is more consistent tool life and fewer interruptions in production, which supports higher process stability and predictable cost per component. Geometry and chip control that improve cycle time and surface finish The combination of a Rhombic 55° form, 0.8 mm corner radius and a negative 0° rake provides a rigid cutting edge for heavy and interrupted cuts. The RK5 chipbreaker is tailored to the fracture-prone chips of cast iron, promoting controlled chip formation and evacuation. This leads to shorter secondary operations and a better surface finish, while the stable edge geometry reduces the risk of edge chipping, enabling higher feed rates where appropriate without compromising part quality. Practical integration into turning operations and machine shops Designed for seamless use in standard toolholders for rhombic inserts, this indexable solution is suitable for a wide range of turning tasks on cast iron components, from roughing to medium finishing. The robust design supports reliable clamping and repeated indexing, and the insert’s characteristics simplify process setup: producers benefit from predictable results and reduced scrap rates. For specific cutting data, tooling alternatives or to verify suitability for a particular cast iron grade, Metav Werkzeuge’s consultants can supply tailored recommendations. Contact Metav Werkzeuge for application-specific cutting data, stock information and advice on using Walter Tools Tiger·tec Silver turning inserts — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: DNMA110408-RK5-WKK10S-WALTER Designation: DNMA110408-RK5 WKK10S Manufacturer: Walter Tools Series: Tiger·tec Silver Grade: WKK10S Core data Insert size: 11 Thickness: 04 Corner radius: 0.8 mm Relief angle: 0° (negative) Shape: Rhombic 55° Tolerance class: M Special features Coated carbide grade Optimised for cast iron (K) RK5 chipbreaker for controlled chips Negative rake for robust cutting Rhombic 55° geometry FAQ Is this insert suitable for cast iron turning? Yes. The DNMA110408-RK5 WKK10S is engineered for machining cast iron (K) and its coating and chipbreaker are optimised for that material group. What does the RK5 chipbreaker do? The RK5 chipbreaker promotes controlled chip formation and reliable evacuation when machining brittle, fracture-prone materials such as cast iron, reducing the chance of long, entangling chips. Can the same insert be used for stainless steel or hardened materials? The WKK10S grade and the insert geometry are specified for cast iron applications; different grades and geometries are recommended for stainless steels or hardened materials. How does the Tiger·tec Silver technology benefit production? Tiger·tec Silver combines a tailored substrate with advanced coating layers to improve wear resistance and edge stability in abrasive cast iron applications, resulting in more consistent performance and fewer index changes. What is the advantage of the rhombic 55° shape and 0.8 mm corner radius? The rhombic 55° form provides secure seating and cutting edge strength, while the 0.8 mm radius balances edge robustness with achievable surface quality for turning operations. Manufacturer: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany The Walter AG (brand appearance: Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanation and reference; there is no affiliation between our company and the manufacturers named. The item offered is an original, factory-new product of the manufacturer.
DNMA150408-RK5 WKK10S WKK10S Wendeplatten - Walter Tools
Benefit from robust chip control, Tiger‑tec Silver wear resistance and a stable rhombic geometry that boost productivity in cast iron turning; the DNMA150408‑RK5 WKK10S combines reliable edge strength with predictable performance. Order the DNMA150408‑RK5 WKK10S directly via Metav Werkzeuge or ask our consultants if needed. DNMA150408-RK5 WKK10S — Turning insert for cast iron, Tiger‑tec Silver — Walter Tools The DNMA150408‑RK5 WKK10S is a rhombic 55° turning insert engineered for efficient machining of cast iron, featuring a Tiger‑tec Silver coating and an RK5 chipbreaker for improved chip control. Tiger‑tec Silver coating for improved wear resistance RK5 chipbreaker for controlled chip formation Rhombic 55° geometry for versatile turning 0.8 mm corner radius for robust edge strength Optimised wear resistance for abrasive cast iron conditions The Tiger‑tec Silver coating, paired with the WKK10S carbide grade, is engineered to resist the abrasive wear typical of cast iron applications. This combination extends tool life and helps maintain consistent dimensional accuracy over longer production runs. Coating technology reduces flank wear by improving thermal stability at the cutting edge; as a result, wear resistance and repeatable surface quality are achieved with fewer insert changes, supporting steady process throughput. Stable geometry that improves cutting reliability The rhombic 55° insert form and the 0° negative rake produce a stable cutting action suited to a range of turning operations. The 0.8 mm corner radius offers enhanced edge strength for interrupted cuts and heavier engagement, while the plate thickness code 04 contributes to rigidity in the clamping system. Together these geometric features result in improved load distribution across the cutting edge and reduced tendency for sudden edge failure, which benefits overall process reliability. Effective chip control and production efficiency The RK5 chipbreaker is tuned for the short, brittle chips typical of cast iron, promoting safe chip flow and preventing entanglement. Controlled chip formation reduces machine downtime for clearing, shortens cycle interruptions and supports higher net productivity. As an indexable insert, the item allows quick rotation to a fresh cutting edge, lowering tool change time and improving overall equipment utilisation in batch and continuous production environments. Application guidance and material suitability Designed specifically for cast iron (ISO group K), the insert accommodates the abrasive and often fracturing chip behaviour encountered with these materials. The combination of coating, chipformer and geometry is selected to balance wear resistance with reliable chip breakage. For newcomers, a chipbreaker is a machined relief on the rake face that shapes chips as they form; the RK5 option helps ensure chips break into manageable segments for safe evacuation and consistent surface finish. Handling is performed using standard insert seats compatible with DNMA‑style turning toolholders. Contact Metav Werkzeuge for tailored application advice on Walter Tools inserts and to request a specification sheet or quotation for the DNMA150408‑RK5 WKK10S. Technical data SKU: DNMA150408-RK5-WKK10S-WALTER Product: Turning insert DNMA150408-RK5 WKK10S Brand: Walter Tools Series: Tiger‑tec Silver Designation: DNMA150408-RK5 Facts Insert size: 15 Corner radius: 0.8 mm Relief angle: 0° (negative) Thickness code: 04 Tolerance class: M Special features Coating: Tiger‑tec Silver Carbide grade: WKK10S Chipbreaker: RK5 Shape: Rhombic 55° Material group suitability: K (cast iron) FAQ What materials is this insert suitable for? The DNMA150408‑RK5 WKK10S is intended for machining cast iron; the grade and chipbreaker are optimised for abrasive cast materials. How does the RK5 chipbreaker affect chip control? The RK5 chipformer on this turning insert promotes short, controlled chip segments during cast iron turning, reducing chip-related interruptions. Is the rhombic 55° geometry versatile for different turning tasks? Yes; the rhombic 55° form provides a balance of accessibility and edge strength, making it suitable for a variety of external turning applications. What does the 0° negative rake signify in practice? A 0° negative rake means a neutral to slightly reinforced cutting angle that stabilises the cutting edge for tougher or interrupted cuts, improving robustness. Can this insert be used in standard DNMA toolholders? The DNMA150408‑RK5 WKK10S corresponds to the DNMA family and is compatible with standard toolholders designed for that insert profile. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand presentation: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and brand names are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands; the offered item is an original, factory‑new product of the manufacturer.
DNMA150408-RK5 WKK20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating, RK5 chipbreaker geometry and a 0.8 mm corner radius for consistently productive machining of cast iron; order the DNMA150408-RK5 WKK20S directly via Metav Werkzeuge or ask our consultants if needed. DNMA150408-RK5 WKK20S indexable turning insert — Tiger‑tec Silver, RK5 chipbreaker, for cast iron | Walter Tools An indexable turning insert, DNMA150408-RK5 WKK20S, designed for stable, high‑productivity turning of cast iron components in industrial machining environments. Tiger·tec Silver coating for enhanced wear resistance RK5 chipbreaker optimised for cast iron chip control Rhombic 55° shape for versatile turning applications 0.8 mm corner radius for improved edge stability Maximise productivity when turning cast iron The insert’s Tiger‑tec Silver coating and the WKK20S coated‑carbide grade are engineered specifically for abrasive cast iron applications. This composition promotes stable chip formation and reduces flank wear, which leads to longer cutting intervals and fewer tool changes. The result is measurable improvements in process efficiency and component throughput, especially in batch production and high‑volume turning operations where tool life and consistency directly affect cost per part. Geometry that controls chips and protects the edge Featuring a rhombic 55° platform and the RK5 chipbreaker, the geometry of this insert supports controlled, short chips typical of cast iron machining. The 0.8 mm corner radius increases edge strength and resistance to chipping, while the 0° (negative) rake provides a robust cutting edge for interrupted cuts or heavy engagement. These design choices combine to reduce downtime from edge failure and to maintain surface quality over longer tool life. Consistent tool life and process security through coating and grade The coated carbide grade in the Tiger‑tec Silver family offers a balance between wear resistance and toughness for abrasive materials. This provides predictable performance across different cast iron types and cutting conditions, improving repeatability in production. The insert’s coated carbide construction helps maintain cutting geometry under thermal and mechanical stress, supporting high process reliability and a steady surface finish on workpieces. For reliable cast‑iron turning with Walter Tools technology, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for specification support and availability Technical Data SKU: DNMA150408-RK5-WKK20S-WALTER Designation: DNMA150408-RK5 WKK20S Manufacturer: Walter Tools Product type: Indexable turning insert Series: Tiger‑tec Silver Grade: WKK20S Chipbreaker: RK5 Shape: Rhombic 55° Relief angle: 0° (negative) Execution: A Tolerance class: M Material group: K (cast iron) Applicability: Cast iron Key Measurements Inscribed circle / size: 15 mm Thickness: 4.0 mm Corner radius: 0.8 mm Special features Coated carbide (Tiger‑tec Silver) Optimised for abrasive wear in cast iron Chip control for short, breakable chips Robust edge for interrupted cuts Suitable for industrial turning applications FAQ What materials is this insert intended for? The DNMA150408-RK5 WKK20S by Walter Tools is specifically suited to machining cast iron (material group K) and has been optimised for the abrasive wear and short, breaking chips typical of those materials. How does the RK5 chipbreaker benefit production? The RK5 chipbreaker on the DNMA150408-RK5 WKK20S controls chip formation to produce short, safely breaking chips, which reduces the risk of entanglement and supports consistent surface quality during cast‑iron turning. What advantage does the Tiger‑tec Silver coating provide? Tiger‑tec Silver coating increases wear resistance and thermal stability for the insert, helping to prolong tool life and ensure repeatable performance in demanding cast‑iron machining tasks. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned only for descriptive purposes. There is no affiliation between our company and the mentioned brands. The offered article is an original, brand‑new product from the manufacturer Walter Tools.
DNMA150412-RK5 WKK20S WKK20S Wendeplatten - Walter Tools
Reliable chip control and the Tiger·tec Silver wear resistance combine to deliver consistent productivity when machining cast iron; the RK5 chipbreaker and a 1.2 mm corner radius ensure robust edge life and predictable chip formation. Order the DNMA150412-RK5 WKK20S insert directly via Metav Werkzeuge or consult our application specialists for tailored recommendations. DNMA150412-RK5 WKK20S indexable turning insert for cast iron — RK5 chipbreaker, Tiger·tec Silver (Walter Tools) The DNMA150412-RK5 WKK20S is a rhombic 55° negative insert engineered for productive turning of cast iron, combining a coated carbide grade with a chipbreaker tuned to short, controlled chips. Tiger·tec Silver coated for high wear resistance RK5 chipbreaker for short, controlled chips Rhombic 55° geometry with 1.2 mm corner radius 0° negative relief for robust, stable cutting Durable coating and grade for abrasive cast-iron work The combination of the Tiger·tec Silver coating and the WKK20S grade provides enhanced resistance to abrasive wear common in cast‑iron machining. The grade is a coated carbide type optimised for ISO group K materials, where frequent short, brittle chips and abrasive constituents can accelerate tool wear. This technical pairing extends productive cutting life, reduces the need for unscheduled index changes and supports more predictable process economics — a rational advantage for batch production and repetitive turning operations. Geometry that controls chips and protects the edge The insert’s RK5 chipbreaker is designed to generate short, easy‑to‑evacuate chips, improving surface integrity and reducing interruption from long swarf. Combined with the rhombic 55° shape and a 1.2 mm corner radius, the geometry balances edge strength with cutting precision. The 0° negative relief provides a robust cutting edge for stable cuts under varying depths of cut and feed, while the tolerance class M ensures repeatable seating and interchangeability in standard clamping systems. These features translate into fewer tool interventions and a steadier production flow. Practical application and workshop benefits Specified with a nominal size of 15 mm and a plate thickness of 4 mm, this insert suits a wide range of turning tasks on cast iron where a reliable, universal grade is required. The insert’s characteristics support both routine finishing and general‑purpose turning across many foundry grades. For process setup, the grade’s behaviour enables conservative starting parameters and subsequent optimisation for cycle time and surface finish. For additional cutting data or application-specific parameters, Metav Werkzeuge’s technical team can provide tailored guidance to integrate the insert into existing tool chains. For application advice, cutting‑data optimisation or a quotation for Walter Tools DNMA150412-RK5 WKK20S inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 — the specialists will advise on the optimal grade and parameters for the intended cast‑iron application Technical Data Article number: DNMA150412-RK5-WKK20S-WALTER SKU: DNMA150412-RK5-WKK20S-WALTER Designation: DNMA150412-RK5 WKK20S Facts Size: 15 mm Thickness: 4 mm Corner radius: 1.2 mm Relief angle: 0° (negative) Shape: Rhombus 55° Tolerance class: M Chipbreaker: RK5 Special features Coating: Tiger·tec Silver Grade: WKK20S (coated carbide) Series: Tiger·tec Silver Suitable for: Cast iron (ISO group K) Execution: A FAQ Which materials is this insert suitable for? The DNMA150412-RK5 WKK20S insert is formulated for machining cast iron, aligned with ISO group K; the WKK20S grade and Tiger·tec Silver coating address abrasive wear and short‑chip conditions typical of these materials. How does the RK5 chipbreaker affect chip formation? The RK5 chipbreaker on this Walter Tools insert produces short, controlled chips that are easier to evacuate from the cutting zone, supporting safer operation and more consistent surface quality. What are the key geometric specifications to consider? The product features a rhombic 55° shape, a 1.2 mm corner radius and a 0° negative relief; the standard size is 15 mm with 4 mm thickness, all of which influence edge strength, insert positioning and achievable feeds. What does the WKK20S grade offer in production? WKK20S is a coated carbide grade within the Tiger·tec Silver family, optimised for wear resistance in cast‑iron turning; it supports reliable performance and predictable tool life under abrasive conditions. What does tolerance class M mean for tool mounting? Tolerance class M indicates standardised dimensional accuracy for the insert, ensuring consistent seating and interchangeability in compatible indexable insert holders. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DNMA150608-RK5 WKK10S WKK10S Wendeplatten - Walter Tools
Benefit from the combination of Tiger·tec Silver coating, the RK5 chipbreaker and a 0.8 mm corner radius for efficient, predictable machining of cast iron; order the required inserts directly via Metav Werkzeuge or consult our specialists for process optimisation. DNMA150608-RK5 WKK10S indexable turning insert for cast iron — Walter Tools (Tiger·tec Silver, Rhombic 55°) DNMA150608-RK5 WKK10S is an indexable turning insert optimised for cast iron machining; it pairs a wear-resistant coated grade with a chipformer designed for short, breaking chips. Tiger·tec Silver coating for wear resistance RK5 chipbreaker for predictable chip control Rhombic 55° geometry for versatile turning 0° negative relief for secure cutting Longer tool life through advanced coating technology The combination of the Tiger·tec Silver coating and the WKK10S grade provides enhanced wear resistance in abrasive cast iron applications. The coated carbide composition is engineered to withstand the frequent, brittle-chip conditions typical of cast iron, reducing flank wear and extending service intervals. By selecting a coating technology optimised for abrasive materials, the insert supports more reliable cycle times and fewer tool changes, which translates into measurable production stability and lower overall tooling costs. Consistent chip control and process reliability Equipped with the RK5 chipbreaker, this indexable plate produces short, controlled chips that reduce the risk of chip entanglement and improve surface quality. The chipformer geometry is tuned for cast iron (K) and therefore minimises interruptions caused by poor chip evacuation. For operations where repeatable cutting behaviour matters, the predictable chip flow supports higher feed rates and helps maintain steady machining parameters, improving throughput without sacrificing component finish. Geometry and edge preparation that support precision work The rhombic 55° insert form and a 0.8 mm corner radius balance strength and profile fidelity for diverse turning tasks. The 55° geometry enables a stable cutting edge while allowing access to a range of part contours; the moderate corner radius reduces edge chipping yet preserves profile accuracy. Additionally, the specified 0° negative relief offers a secure seating and robust engagement in turning holders, which is especially useful for interrupted cuts or unstable setups where insert retention and edge strength are critical. Clear application focus and simple integration This insert is explicitly designated for machining cast iron, matching the ISO group K requirements for short, brittle chips and abrasive material behaviour. The designation and series information make it straightforward to match the insert to existing toolholders and machining strategies. For engineers and production planners seeking an insert tuned to cast-iron dynamics, the combination of grade, chipbreaker and geometry simplifies specification decisions and helps standardise tooling across relevant turning operations. Order genuine Walter Tools DNMA150608-RK5 WKK10S inserts from Metav Werkzeuge for consistent cast iron performance or contact our consultants for detailed process recommendations Technical Data SKU: DNMA150608-RK5-WKK10S-WALTER Designation: DNMA150608-RK5 WKK10S Product type: indexable turning insert Manufacturer: Walter Tools Facts Plate size: 15 mm Thickness: 06 Corner radius: 0.8 mm Relief angle: 0° (negative) Geometry: Rhombic 55° Tolerance class: M Special features Coating: Tiger·tec Silver Grade: WKK10S (coated carbide) Chipbreaker: RK5 Series: Tiger-tec Silver Execution: A Suitable for: cast iron (K) FAQ What materials is this insert designed for? The DNMA150608-RK5 WKK10S insert is designed for machining cast iron and is specified for ISO group K applications. How does the RK5 chipbreaker affect machining? The RK5 chipbreaker on the Walter Tools insert produces short, controlled chips that enhance chip evacuation and surface quality during cast iron turning. Is the coating suitable for abrasive workpieces? Yes, the Tiger·tec Silver coating on the WKK10S grade is formulated to improve wear resistance in abrasive cast iron machining. What geometric advantages does the rhombic 55° provide? The Rhombic 55° geometry offers a robust cutting edge and good access to varied part contours, supporting versatile turning operations with reliable edge strength. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com