DNMG110404-MM5 WMP20S WMP20S Wendeplatten - Walter Tools
Combining Tiger·tec Silver coated carbide with the MM5 chipbreaker and a robust 0.4 mm corner radius delivers stable chip formation and extended edge life in demanding stainless‑steel turning operations; order the DNMG110404‑MM5 WMP20S directly via Metav Werkzeuge or consult our technical advisors for application-specific recommendations. DNMG110404‑MM5 WMP20S Turning insert — Tiger·tec Silver for rostfreier Stahl by Walter Tools The DNMG110404‑MM5 WMP20S is an indexable turning insert engineered for medium to robust machining of rostfreier Stahl, providing reliable chip control and consistent cutting-edge performance in general turning applications. Tiger·tec Silver coating for stable edges Optimised for rostfreier Stahl (ISO M) Rhombic 55° insert with 0.4 mm corner radius Consistent process security through advanced coating technology The Tiger·tec Silver series combines a coated carbide substrate with targeted surface engineering to reduce flank wear and support repeatable performance under difficult conditions. As a coated grade, WMP20S improves heat resistance and contributes to stable chip formation, which lowers the risk of built‑up edge when machining rostfreier Stahl. This results in fewer interruptions for tool changes and a more predictable production rhythm, helping to maintain throughput on multi‑shift operations. Geometry that improves surface quality and edge strength The rhombic 55° format and the negative 0° relief angle give this insert high rigidity and reliable seating in the toolholder, while the 0.4 mm corner radius balances edge strength with the ability to produce good surface finish. The integrated MM5 chipbreaker is designed to control chips in a wide range of feeds, reducing the likelihood of long, stringy swarf and improving chip evacuation. Together, these features allow stable cuts with consistent part quality and reduced secondary finishing. Shop‑floor benefits: productivity, repeatability and tool life Designed for moderate to heavy conditions typical for rostfreier Stahl, the grade supports secure material removal rates and extended tool life thanks to its wear‑resistant coating and robust edge geometry. The insert’s dimensions and form enable straightforward toolholder selection and quick indexation, which minimises setup time and contributes to overall process economy. Using a proven series from a recognised supplier reduces variability between batches and supports predictable maintenance planning. For reliable turning performance with Walter Tools’ Tiger·tec Silver grade, contact Metav Werkzeuge for supply and application guidance — eMail: info@metav-werkzeuge.com or call +49 2822 7131930. Technical Data Article number: DNMG110404-MM5-WMP20S-WALTER Designation: DNMG110404-MM5 WMP20S Type: Turning insert / indexable insert Brand: Walter Tools Core specifications Insert size: 11 Thickness: 04 Corner radius: 0.4 mm Relief angle: 0° (negative) Insert shape: Rhombic 55° Special features Series: Tiger·tec Silver Grade: WMP20S (coated carbide) Chipbreaker: MM5 Suitable application: rostfreier Stahl (ISO M) Execution: G FAQ What materials is this insert suitable for? The DNMG110404‑MM5 WMP20S is optimised for machining rostfreier Stahl (ISO M), offering secure chip formation and edge stability in these alloys. How does the Tiger·tec Silver coating affect performance? Tiger·tec Silver on the WMP20S grade improves heat resistance and flank wear behaviour, extending effective tool life under the typical thermal loads encountered when turning rostfreier Stahl. Which chip control can be expected with the MM5 breaker? The integrated MM5 chipbreaker produces compact, controllable chips across a range of feeds, reducing swarf issues and aiding automated or constrained machining setups. Is this insert compatible with standard DNMG toolholders? Yes, the DNMG form follows common DNMG dimensions and indexes in compatible toolholders, enabling straightforward replacement and quick indexation. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand presentation: Walter Tools), headquartered in Tübingen, is one of the world's leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names remain the property of their respective owners. Mention of brand names and trademarks is for explanatory purposes only; there is no affiliation between our company and the named brands. The offered item is original, factory‑new goods of the respective manufacturer.
DNMG110404-MM5 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating, a stabilising MM5 chipbreaker and a compact rhombic 55° form for consistent performance in demanding turning applications; order the insert directly via Metav Werkzeuge or consult the technical advisers for machining guidance. DNMG110404‑MM5 WSM10S indexable turning insert — Tiger·tec Silver, Walter Tools DNMG110404‑MM5 WSM10S is an indexable turning insert designed for heavy-duty and heat‑resistant materials, offering process-stable cutting in stainless and superalloy applications Tiger·tec Silver heat-resistant coating Optimised MM5 chipbreaker for secure chip control Rhombic 55° insert form for versatile turning Negative 0° rake for high cutting-edge stability Consistent tool life through advanced grade technology The WSM10S grade, part of the Tiger·tec Silver family, provides a balance of thermal resistance and edge strength that prolongs cutting-edge life when machining tough materials. The coated cemented carbide composition reduces wear from high temperatures and adhesion, which results in fewer interruptions for tool changes and more predictable performance per insert. This translates into measurable productivity gains when processing materials classified under ISO groups M and S, including rostfreier Stahl and heat‑resistant superalloys. Geometry engineered for reliable chip control and surface quality The rhombic 55° geometry combined with the MM5 chipbreaker ensures controlled chip formation and evacuation under variable cutting conditions. The insert’s negative 0° rake increases radial stability and supports heavy cuts without premature edge failure. A corner radius of 0.4 enhances robustness at the cutting edge while maintaining acceptable surface finish, making the insert suitable for interrupted cuts and challenging turning operations where chip flow and edge integrity are decisive. Application focus: high‑temperature alloys and stainless steels Built for demanding turning tasks, this insert is tailored to applications in which thermal resistance and a stable cutting edge are critical. The WSM10S grade excels in machining rostfreier Stahl and materials that tend to work‑harden or generate adhesive build‑up. Selecting this insert can reduce the need for conservative feeds and speeds, improving cycle times while maintaining part quality. The result is a pragmatic balance between tool life and machining throughput in serial production. Identification, compatibility and process integration Marked as DNMG110404‑MM5 WSM10S, the insert follows common ISO insert designation and fits standard DNMG toolholders, simplifying inventory management and tool change processes. The part is produced to tolerance class M, ensuring consistent seat and clamping fit in compatible tool systems. For machining set‑up data or recommendations on cutting parameters for specific alloys, Metav Werkzeuge’s technical advisers can supply apex heights, recommended feeds and speeds, and applicability notes. For supply and machining consultancy relating to Walter Tools' Tiger·tec Silver inserts, contact Metav Werkzeuge — Metav Werkzeuge can advise on selection and availability at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: DNMG110404‑MM5‑WSM10S‑WALTER Designation: DNMG110404‑MM5 WSM10S Series: Tiger·tec Silver Manufacturer: Walter Tools Facts Plate size: 11 Thickness code: 04 Corner radius: 0.4 Free angle: 0° (negative) Tolerance class: M Special features Grade: WSM10S Chipbreaker: MM5 Shape: Rhombic 55° Material designation: S / M Suitable for: rostfreier Stahl Execution: G ISO designation: DNMG110404‑MM5 WSM10S FAQ Which materials suit this insert best? The DNMG110404‑MM5 WSM10S insert is optimised for ISO groups M and S, making it suitable for rostfreier Stahl and heat‑resistant superalloys where thermal resistance and secure chip formation are required. How does the MM5 chipbreaker influence machining? The MM5 chipbreaker provides controlled chip formation and easier evacuation, improving process stability and reducing the risk of built‑up edge with the Tiger·tec Silver grade. What does the rhombic 55° form mean for tool use? The rhombic 55° geometry gives a versatile cutting angle for both roughing and finishing passes and permits use in common DNMG holders for efficient tool changes with repeatable seating. Is the insert compatible with standard DNMG holders and what is the SKU? Yes, the insert follows the DNMG family standard; SKU DNMG110404‑MM5‑WSM10S‑WALTER identifies the Walter Tools indexable turning insert for straightforward compatibility checks. What tolerance and edge radius are specified for precision work? The insert is manufactured to tolerance class M with a corner radius of 0.4, offering balanced edge strength and acceptable surface finish for general turning tasks. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes and do not indicate any affiliation between our company and the named manufacturers. The offered item is an original, factory‑new product from Walter Tools.
DNMG110404-MM5 WSM20S Wendeplatten - Walter Tools
Die Kombination aus der Tiger·tec Silver Beschichtung und der WSM20S Hartmetallsorte liefert eine robuste Schneidkante und sichere Spanbildung bei schwer zerspanbaren Werkstoffen; dies reduziert Rüstzeiten und erhöht die Produktionseffizienz. Bestellen über Metav Werkzeuge oder technische Beratung anfragen. DNMG110404‑MM5 WSM20S indexable turning insert, Tiger·tec Silver, negative 0° rake — Walter Tools The DNMG110404‑MM5 WSM20S is an indexable turning insert designed for heavy-duty finishing and semi‑finishing of stainless steels and heat‑resistant alloys, combining a protective coating and a geometry optimised for secure chip control. Tiger·tec Silver coated carbide grade WSM20S Optimised for rostfreie Stähle and superalloys Rhombic 55° geometry for versatile turning MM5 chipbreaker for controlled chip formation High‑temperature performance for stable production The combination of the Tiger·tec Silver coating and the WSM20S coated carbide grade delivers enhanced thermal resistance and improved flank wear performance during continuous turning operations. This grade is engineered to manage the high heat and adhesion tendencies of stainless steels and heat‑resistant superalloys, which in practice means longer tool life and fewer interruptions for insert changes. The protective multi‑layer coating reduces diffusion and chemical wear at elevated temperatures, supporting a consistent cutting edge under demanding cutting conditions. Geometry that secures chip control and surface quality The rhombic 55° shape with a 0.4 mm corner radius and a negative 0° rake provides mechanical strength at the cutting edge and predictable engagement angles for axial and radial cuts. The MM5 chipbreaker is tailored to generate short, controllable chips in adhesive materials, lowering the risk of built‑up edge and improving surface finish. Together these features enable a reliable balance between cutting force and edge stability, which is crucial when machining materials that tend to work‑harden or form long, stringy chips. Application spectrum and process benefits Specified for ISO groups M and S, this insert is suitable for rostfreie Stähle and heat‑resistant alloys, including titanium and nickel‑based superalloys, depending on cutting parameters and toolholder setup. Its design supports consistent metal removal rates and predictable wear progression, which contributes to higher process security and repeatable part quality. In production environments where downtime and process variability are critical, the insert’s combination of coating and geometry helps to reduce cycle time variation and maintain surface integrity. Integration into tooling systems and economical operation The insert conforms to standard DNMG toolholder interfaces and is available in the compact size indicated by its designation, facilitating straightforward replacement and inventory management. Robust edge strength reduces the frequency of index‑changes, while the coated substrate aids resistance to thermal and abrasive wear, supporting better overall economy of machining operations. For customers seeking production reliability, the Walter Tools Tiger·tec Silver series is positioned to deliver consistent performance and predictable tool life. For advice on selecting the optimal Walter Tools insert with Tiger·tec Silver for specific applications, contact Metav Werkzeuge for technical consultation by phone or email Technical data SKU: DNMG110404-MM5-WSM20S-WALTER Designation: DNMG110404-MM5 Full designation: DNMG110404-MM5 WSM20S Manufacturer: Walter Tools Product type: Indexable turning insert Series: Tiger·tec Silver Grade: WSM20S Facts Plate form: Rhombus 55° Corner radius: 0.4 mm Free rake angle: 0° (negative) Plate size: 11 Plate thickness: 04 Chipbreaker: MM5 Tolerance class: M Special features Coated carbide grade Suited for rostfreie Stähle (ISO M) Suited for heat‑resistant alloys and titanium (ISO S) Robust cutting edge for heavy‑duty turning FAQ What materials is this insert suitable for? The DNMG110404‑MM5 WSM20S insert is specified for ISO groups M and S, making it suitable for rostfreie Stähle and heat‑resistant superalloys, with the Tiger·tec Silver coating aiding performance under high thermal load. How does the MM5 chipbreaker affect machining? The MM5 chipbreaker on this Walter Tools insert produces shorter, controlled chips in adhesive and work‑hardening materials, improving surface finish and reducing the risk of built‑up edge. Is the geometry suitable for both finishing and semi‑finishing? Yes; the rhombic 55° shape combined with a 0.4 mm corner radius and negative rake provides a compromise between edge strength and cutting precision, appropriate for finishing and semi‑finishing applications. Can this insert be used in standard DNMG toolholders? The insert designation follows standard DNMG interfaces and is compatible with toolholders designed for DNMG inserts, facilitating straightforward replacement and clamping. What advantages does the Tiger·tec Silver coating provide? Tiger·tec Silver coating improves thermal stability and reduces diffusion wear, which supports longer tool life and consistent cutting performance on challenging materials. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany The Walter AG (brand: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and proprietary product names belong to their respective owners. Brand names and registered trademarks are mentioned for explanation only. There is no affiliation between our company and the named brands. The offered item is an original, factory‑new product from the manufacturer. 📧 info@metav-werkzeuge.com ☎️ +49 2822 7131930
DNMG110404-MM5 WSM30S WSM30S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Silver coating, the WSM30S grade and the MM5 chipbreaker for stable edge life and reliable chip control; order this insert directly via Metav Werkzeuge or consult our technical team for application guidance. DNMG110404‑MM5 WSM30S DNMG110404‑MM5 WSM30S Turning insert (Rhombic 55°, r0.4) — Walter Tools A DNMG110404‑MM5 WSM30S turning insert designed for heavy and demanding machining of rostfreier Stahl and heat‑resistant superalloys, offering robust edge stability and consistent chip formation. Tiger‑tec Silver coating for high wear resistance WSM30S grade for rostfreier Stahl and superalloys MM5 chipbreaker for controlled chips Rhombic 55° form with r0.4 corner radius Consistent wear resistance for demanding alloys The combination of the Tiger‑tec Silver technology and the WSM30S grade creates a coating/substrate system optimised for abrasive and adhesive wear mechanisms common in rostfreier Stahl and high‑temperature alloys. This results in extended tool life under elevated cutting temperatures and helps maintain a predictable cutting edge during prolonged cycles. The coated cemented carbide composition supports stable performance where thermal load and work hardening would otherwise reduce productivity. Reliable chip control and secure edge stability With the integrated MM5 chipbreaker and a rhombic 55° geometry, the insert delivers controlled chip segmentation even in sticky materials. The negative 0° clearance and the r0.4 corner radius reduce the tendency for built‑up edge and strengthen the cutting zone against mechanical shock. This configuration improves process security during interrupted cuts and heavy depths of cut, translating into fewer tool changes and less unplanned downtime while preserving surface integrity. Designed for productivity and straightforward integration The insert's dimensions and tolerance class M ensure repeatable seating and compatibility with standard toolholders, allowing quick tool exchange and predictable results in serial turning operations. Its focus on rostfreier Stahl and S‑group materials makes it particularly suitable for workshops and production lines machining stainless components or heat‑resistant superalloys where consistent surface finish and dimensional stability are priorities. Choosing this insert supports higher material removal rates without sacrificing edge life or process stability. Contact Metav Werkzeuge today for an application assessment of the Walter Tools DNMG110404‑MM5 WSM30S turning insert, specify the machining material and process parameters via info@metav-werkzeuge.com or call +49 2822 7131930 to receive tailored recommendations and availability details Technical data Article number: DNMG110404-MM5-WSM30S-WALTER Designation: DNMG110404-MM5 ISO designation: DNMG110404-MM5 WSM30S Grade: WSM30S Series: Tiger‑tec Silver Manufacturer: Walter Tools Numbers / Core technical data Insert size: 11 mm Corner radius: 0.4 mm Thickness: 4 mm Relief angle: 0° (negative) Tolerance class: M Form angle: 55° Designs / Special features Chipbreaker: MM5 Coating technology: Tiger‑tec Silver Suitable for: rostfreier Stahl (M), heat‑resistant superalloys and titanium (S) Application: turning indexable insert Execution: G FAQ What materials is this insert best suited for? The DNMG110404‑MM5 WSM30S turning insert from Walter Tools is designed primarily for rostfreier Stahl and for heat‑resistant superalloys and titanium (ISO groups M and S), providing optimised performance where thermal resistance and chip control are critical. How does the MM5 chipbreaker affect machining? The MM5 chipbreaker on the Walter Tools DNMG110404‑MM5 WSM30S promotes predictable chip formation and evacuation, reducing the risk of tangling or edge build‑up during medium to heavy turning operations. Is the insert compatible with standard toolholders? Yes, the DNMG110404‑MM5 conforms to common ISO insert dimensions and tolerance class M, ensuring reliable seating and interchangeability with standard turning toolholders designed for DNMG‑style inserts. What benefit does the r0.4 corner radius provide? A corner radius of r0.4 increases edge strength and distributes cutting forces more evenly, supporting longer edge life on interrupted cuts and helping to maintain surface finish when machining rostfreier Stahl. Can this insert be used for finishing operations? While the DNMG110404‑MM5 WSM30S is optimised for robust cutting and stable chip control, it can be applied for semi‑finishing and finishing depending on cutting parameters; selecting appropriate feeds and speeds enhances surface quality and prolongs insert life. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenbezeichnungen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DNMG110404-MP3 WPP10G WPP10G Wendeplatten - Walter Tools
The combination of Tiger·tec Gold coating and the WPP10G grade delivers extended tool life and reliable chip control in steel turning. With the MP3 chipbreaker and a rhombic 55° form, efficient, repeatable turning and consistent surface quality are ensured. Order the DNMG110404-MP3 WPP10G directly via Metav Werkzeuge or ask our consultants for application advice. DNMG110404-MP3 WPP10G Walter Tools – Tiger·tec Gold coated indexable insert with MP3 chipbreaker The DNMG110404-MP3 WPP10G is a negative‑geometry turning insert designed for productive steel machining with a Tiger·tec Gold coated carbide grade and MP3 chipbreaker for controlled chip formation. Tiger·tec Gold coating for extended life MP3 chipbreaker for reliable chip control Rhombic 55° geometry for versatile turning 0.4 mm nose radius for fine surface finish Longer tool life and stable cutting with Tiger·tec Gold The proprietary Tiger·tec Gold coating combined with the WPP10G grade provides a balance between wear resistance and toughness, intended specifically for steel applications. This combination reduces flank and crater wear under the thermal and mechanical loads typical of steel machining, which translates into fewer insert changes and lower process interruptions. As a coated carbide solution, it is optimised to withstand variable cutting conditions while maintaining tool edge stability and consistent dimensional results. Predictable chip control that raises throughput The MP3 chipbreaker is engineered to produce short, controllable chips in a wide range of feeds and depths of cut, improving swarf management and machine uptime. Controlled chip evacuation reduces the risk of workpiece damage and tool edge impingement, supporting higher uninterrupted cutting lengths and more reliable cycle times. For production environments seeking repeatable performance, the insert’s chip‑forming geometry supports a stable, economic metal‑cutting process. Geometry tuned for versatility and surface quality The rhombic 55° insert form with a 0.4 mm nose radius and negative 0° relief offers a versatile geometry for medium to fine turning operations. The sharper entry angle facilitates access to shoulder transitions and internal profiles, while the small nose radius assists in achieving improved surface finishes without sacrificing strength. This geometry is particularly useful for mixed production runs where a balance between finish and productivity is required. Clear application range and process guidance Designed for the ISO P group, this insert is intended primarily for unalloyed and alloyed steel machining, where heat and chip formation demand a robust, wear‑resistant grade. The DNMG110404-MP3 WPP10G suits general turning tasks and can be used in finishing to light roughing, depending on machine rigidity and cutting parameters. For specific cutting data, recommended feeds, and speeds tailored to a given setup, Metav Werkzeuge’s consultants are available to provide application support and ensure the insert is matched to the intended process. Contact Metav Werkzeuge for detailed application recommendations and immediate availability of the Walter Tools DNMG110404-MP3 WPP10G insert Technical data Article number: DNMG110404-MP3-WPP10G-WALTER Wording / ISO designation: DNMG110404-MP3 WPP10G Series: Tiger‑tec Gold Grade: WPP10G Facts Plate form: Rhombus 55° Corner radius: 0.4 mm Plate size: 11 Plate thickness: 04 Relief angle: 0° (negative) Tolerance class: M Special features Coating: Tiger·tec Gold (coated carbide) Chipbreaker: MP3 Material application: Steel (ISO group P) Execution: G Manufacturer: Walter Tools FAQ What materials is this insert suitable for? The DNMG110404-MP3 WPP10G is designed for ISO P materials and is optimised for machining unalloyed and alloyed steel. What advantage does the Tiger·tec Gold coating provide? Tiger·tec Gold on the WPP10G grade improves wear resistance and edge stability, extending the service life of the insert under typical steel cutting conditions. How does the MP3 chipbreaker affect production? The MP3 chipbreaker delivers predictable, short chips which enhance swarf control and reduce interruptions, supporting higher machine throughput and safer handling. Is the insert suitable for fine finishing? With its rhombic 55° geometry and 0.4 mm nose radius, the insert can be used for fine finishing operations where machine rigidity and the correct cutting parameters are observed. What is the exact ISO designation of the insert? The ISO designation is DNMG110404-MP3 WPP10G, specifying the geometry, chipbreaker and grade for clear reference in tool lists. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand: Walter Tools) is a leading manufacturer of precision tools for metalworking and is part of the Sandvik group. Trademarked names and product designations are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only; there is no affiliation between our company and the mentioned brands. The offered article is an original, brand‑new product from the manufacturer.
DNMG110404-MP3 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of the WPP20G Tiger·tec Gold coating together with the MP3 chipbreaker and a stable Rhombic 55° geometry to achieve consistent chip control and extended tool life in steel turning operations; order the insert directly via Metav Werkzeuge or consult the team for application advice. DNMG110404-MP3 WPP20G — Turning insert, Tiger·tec Gold, for steel — Walter Tools The DNMG110404-MP3 WPP20G is a Tiger·tec Gold coated turning insert designed for general steel machining, offering stable chip formation and reliable performance in interrupted and continuous cuts. Tiger·tec Gold coating for wear resistance WPP20G grade: versatile for steel machining MP3 chipbreaker for controlled chip formation Rhombic 55° insert with 0.4 mm corner radius Predictable chip behaviour to keep cycles stable The MP3 chipbreaker on this insert delivers controlled chip formation, which reduces the risk of entangling long chips and lowers the likelihood of unplanned stops. In practical terms, the defined chip geometry reduces manual intervention and supports steady cycle times on automated lathes and conventional turning centres. The chip control is particularly effective when machining unalloyed and alloyed steel, where consistent evacuation of material helps maintain surface finish and tool life. Coating and grade tailored for extended service life Equipped with the Tiger·tec Gold multilayer coating and the WPP20G cemented-carbide grade, the insert offers a balanced combination of hardness and toughness for diverse steel applications. The coating reduces abrasive wear and improves thermal resistance during higher cutting speeds, while the substrate composition maintains edge strength under intermittent cuts. This pairing translates into longer productive tool life and fewer tool changes, supporting higher uptime and lower per-part tooling cost. Geometry and mounting deliver stability and versatility The rhombic 55° form and the 0° (negative) rake create a robust cutting edge that resists vibration during facing and turning operations; the 0.4 mm corner radius contributes to a stronger edge and improved surface integrity on the workpiece. The insert size and thickness suit standard toolholders for DNMG formats, enabling straightforward integration into existing toolsets and quick changeover. Together, the geometry and chipbreaker help to achieve consistent results across a wide range of machining parameters. Contact Metav Werkzeuge for specific application recommendations and stock availability at info@metav-werkzeuge.com or +49 2822 7131930 — reference the DNMG110404-MP3 WPP20G for rapid assistance Technical Data Article number: DNMG110404-MP3-WPP20G-WALTER Label: Drehwendeschneidplatte DNMG110404-MP3 WPP20G Walter Tools Manufacturer: Walter Tools Facts Insert size: 11 mm Thickness: 4 mm Corner radius: 0.4 mm Clearance / rake: 0° (negative) Shape: Rhombic 55° Tolerance class: M Special features Series: Tiger·tec Gold Grade: WPP20G Chipbreaker: MP3 Substrate: coated cemented carbide Application: steel machining Geometry: DNMG format, negative rake, robust cutting edge FAQ What materials is this insert intended for? The DNMG110404-MP3 WPP20G is specified for machining steel and is optimised for the thermal and chip-formation characteristics typical of unalloyed and alloyed steels. How does the MP3 chipbreaker affect performance? The MP3 chipbreaker promotes short, controlled chips and reliable evacuation, which reduces the risk of chip-related machine stoppages and improves cycle-time consistency with this Walter Tools insert. Can the insert be used for interrupted cuts? Yes, the combination of the rhombic 55° geometry, negative rake and WPP20G grade offers robust edge strength suitable for interrupted and light-to-medium roughing operations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DNMG110404-MP5 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of durable Tiger·tec Gold coating, precise MP5 chip control and a robust rhombic geometry for stable, economical steel machining; order the insert directly via Metav Werkzeuge or consult our team for application-specific advice. DNMG110404-MP5 WPP10G Turning Insert — Tiger·tec Gold coated, MP5 chipbreaker, for steel — Walter Tools The DNMG110404-MP5 WPP10G is a rhombic 55° indexable turning insert engineered for versatile steel turning with a coated carbide grade from Walter Tools Tiger·tec Gold coating for longer life MP5 chipbreaker for consistent chip control Rhombic 55° geometry for versatile turning Negative 0° rake for robust interrupted cuts Dependable performance for steel turning operations The DNMG110404-MP5 WPP10G insert combines a coated carbide grade developed for steel with a proven geometry to deliver repeatable results in production environments. The WPP10G grade, part of the Tiger·tec Gold series, is optimised for the thermal and mechanical demands of machining unalloyed and alloyed steel, which reduces tool wear and contributes to longer intervals between indexings. The specification with a corner radius of 0.4 mm and a standard inscribed size ensures predictable cutting engagement and surface integrity on turned parts. Coating and chip control that boost uptime A high-performance coating reduces flank wear and improves resistance to adhesion and diffusion at elevated cutting temperatures. The Tiger·tec Gold finish enhances edge stability and increases the number of cutting cycles before change‑over. Combined with the engineered MP5 chipbreaker, the insert achieves consistent chip formation and evacuation, which lowers the risk of chip-related damage to the workpiece and toolholder. The result is measurable productivity gains and fewer interruptions on the shop floor. Geometry and rake designed for robustness and flexibility The rhombic 55° shape provides a versatile approach angle for both general turning and finishing passes, while the negative 0° rake gives additional strength at the cutting edge for interrupted cuts and heavy cross‑sections. This balance of geometry and rake angle makes the insert suitable for a wide range of turning tasks where stability and edge protection are priorities. The nominal plate thickness and form factor support secure clamping and repeatable positioning in common toolholders. Practical benefits and application guidance Selection of the DNMG110404-MP5 WPP10G yields practical advantages: improved tool life thanks to the coated grade, reliable chip control via MP5, and flexible applicability across many steel grades as defined by ISO group P. For shops seeking to enhance throughput, this insert reduces rework and minimises downtime from unexpected edge failure. For best results, pair the insert with suitable clamping systems and machining parameters matched to the workpiece material and batch size. Contact Metav Werkzeuge for detailed cutting data and to source Walter Tools DNMG110404-MP5 WPP10G inserts; the Metav Werkzeuge team can advise on feeds, speeds and holder compatibility — info@metav-werkzeuge.com / +49 2822 7131930 Technical Data SKU: DNMG110404-MP5-WPP10G-WALTER Article designation: DNMG110404-MP5 ISO designation: DNMG110404-MP5 WPP10G Manufacturer: Walter Tools Facts Series: Tiger·tec Gold Grade: WPP10G Chipbreaker: MP5 Shape: Rhombus 55° Corner radius: 0.4 mm Plate size: 11 Thickness: 04 Free rake angle: 0° (negative) Tolerance class: M Special features Coating: Tiger·tec Gold Material application: Steel (P) Substrate: Coated carbide Execution: G Inscribed designation: DNMG110404-MP5 WPP10G FAQ What materials is this insert intended for? The DNMG110404-MP5 WPP10G insert is intended primarily for machining steel (ISO group P); the WPP10G grade is optimised for the thermal and chip characteristics of steel turning. Which chipbreaker does the insert use and what is the benefit? This insert features the MP5 chipbreaker, which provides predictable chip formation and evacuation, improving surface finish and reducing rework in continuous and semi‑continuous turning operations. How does the Tiger·tec Gold coating affect tool life? The Tiger·tec Gold coating increases edge stability and wear resistance under typical steel cutting conditions, extending service life compared with uncoated grades and helping to maintain consistent component quality. Is the negative rake suitable for interrupted cuts? Yes, the negative 0° rake enhances edge strength, making this insert suitable for interrupted cuts and more robust turning operations where edge protection is essential. Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned solely for explanatory purposes. There is no connection between our company and the brands named. The offered item is original, brand‑new goods from the manufacturer.
DNMG110404-MP5 WPP20G WPP20G Wendeplatten - Walter Tools
Take advantage of high process security and broad material coverage thanks to the Tiger·tec Gold grade and the MP5 chipformer; the result is consistent chip control and extended cutting-edge life for steel turning operations. Order or request personalised advice via Metav Werkzeuge for optimal cutter selection and reliable supply. DNMG110404-MP5 WPP20G turning insert (Tiger·tec Gold) – Rhombus 55°, for steel, Walter Tools The DNMG110404-MP5 WPP20G is a coated carbide turning insert engineered for robust steel machining, offering a Rhombic 55° geometry and a small corner radius for precise finishing and stable roughing. Tiger·tec Gold coating for long tool life Optimised for steel machining applications Rhombic 55° geometry with 0.4 mm radius MP5 chipformer for predictable chip control Consistent productivity and economy for steel turning The combination of a coated carbide substrate and the Tiger·tec Gold technology provides a reliable balance between wear resistance and toughness. This grade, designated WPP20G, is tuned for steel applications (ISO group P) and is suitable where standard toughness and abrasion resistance are required. The result is a reduced frequency of insert changes and predictable tool-life behaviour, which supports continuous production and lowers overall machining cost per component. Explaining briefly, coating layers reduce friction and heat at the cutting edge, which in turn slows abrasive wear and improves dimensional stability during long cycles. Geometry and stability that support surface quality A rhombic 55° shape combined with a 0.4 mm corner radius delivers a compromise between edge strength and the ability to produce fine surface finishes. The negative 0° rake provides a robust cutting edge that resists chipping under interrupted cuts or harder workpiece zones. The integrated MP5 chipformer shapes chips to evacuate reliably in a wide range of cutting conditions, reducing the risk of built-up edge and machine stoppages. For users unfamiliar with chipformers: the design directs and breaks chips to prevent entanglement, which improves process reliability and reduces secondary operations to clear swarf. Practical guidance for process integration Inserts from the Tiger·tec Gold series perform best under stable clamping and consistent cutting parameters; follow manufacturer recommendations for speeds and feeds adapted to the chosen steel grade. The medium tolerance class (M) ensures interchangeability across holders designed for DNMG 1104 style bodies, while the plate designation 04 identifies the standard insert thickness. When replacing inserts, verify seat condition and tightening torque to maintain repeatable geometry and avoid accelerated wear. For tailored machining strategies and parameter suggestions, consultants at Metav Werkzeuge can advise on optimisation for specific component materials and cycle times. Discuss cutting strategy and availability with Metav Werkzeuge for the WPP20G Tiger·tec Gold inserts; contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for competent advice and fast delivery. Technical Data Article number: DNMG110404-MP5-WPP20G-WALTER Product: DNMG110404-MP5 WPP20G Type: Turning insert (Drehwendeschneidplatte) Brand: Walter Tools Core dimensions Size: 11 Thickness: 04 Corner radius: 0.4 mm Geometry: Rhombus 55° Special features Grade: WPP20G Coating / series: Tiger·tec Gold Chipformer: MP5 Rake angle: 0° (negative) Tolerance class: M Material application: Steel (ISO group P) FAQ What materials is this insert intended for? The DNMG110404-MP5 WPP20G insert is designed primarily for steel machining (ISO group P) and the WPP20G grade optimises wear resistance for typical steel cutting conditions. How does the Tiger·tec Gold coating affect performance? Tiger·tec Gold coating on the WPP20G grade increases resistance to abrasive wear and reduces friction at the cutting edge, extending tool life and enhancing process stability in steel turning. What benefit does the MP5 chipformer provide? The MP5 chipformer shapes and controls chips to improve evacuation and reduce the risk of entanglement, which contributes to more reliable, continuous machining with fewer interruptions. Is the insert suitable for interrupted cuts or harder zones in the workpiece? Yes, the negative 0° rake and the robust geometry of the DNMG110404-MP5 provide good resistance against edge chipping, making it suitable for operations with occasional interruptions or varying material hardness. Which toolholders are compatible with this insert designation? Holders designed for DNMG 1104-style inserts will accept this type; ensure the clamping seat is in good condition and follow the holder manufacturer's torque specifications to preserve cutting geometry and repeatability. The Walter AG (brand: Walter Tools) with headquarters in Tübingen is a leading manufacturer of precision tools for metalworking and is part of the Sandvik Group. Protected trademarks and product names are the property of their respective owners. The mentioned brand is used solely for explanation; there is no affiliation with our company, and the article offered is an original, factory-new product from the manufacturer.
DNMG110404-MP5 WPP30G WPP30G Wendeplatten - Walter Tools
Take advantage of the proven Tiger·tec Gold coating and the MP5 chipbreaker for stable, productive steel turning; these features combine to deliver reliable chip control and extended tool life. Order the DNMG110404-MP5 WPP30G directly via Metav Werkzeuge or ask the consultants if technical selection support is required. DNMG110404-MP5 WPP30G indexable turning insert — Tiger·tec Gold, MP5 chipbreaker, for steel The DNMG110404-MP5 WPP30G is a rhombic 55° indexable turning insert designed for general steel machining where consistent chip formation and robust cutting edges are required. Coated carbide Tiger·tec Gold grade WPP30G MP5 chipbreaker for controlled chip formation Rhombic 55° geometry, 0.4 mm corner radius Negative 0° rake for stable, heavy cuts More throughput and predictable tool life with Tiger·tec Gold The advanced Tiger·tec Gold coating technology on this coated carbide grade reduces friction and improves thermal resistance, which translates into longer tool life and more consistent component quality. For operations focused on machining Steel (P), the combination of grade WPP30G and the coating supports stable wear behaviour under the typical temperatures and chip conditions encountered in turning. This makes the insert a rational choice where process reliability and repeatable tolerances are priorities. Controlled chips and secure surface finish thanks to MP5 The MP5 chipbreaker is engineered to produce manageable chips in a broad range of steel alloys, helping to avoid entanglement and improve surface finish. By promoting predictable chip shapes, this geometry also reduces the risk of built-up edge and contributes to uninterrupted production cycles. The result is less rework and fewer interruptions—advantages that directly affect machining efficiency and overall throughput. Geometry optimised for stability and heavier cuts The rhombic 55° cutting angle combined with a 0.4 mm corner radius and a negative 0° rake offers mechanical strength at the cutting edge and good engagement for heavier cuts. These geometry choices support secure cutting under interrupted cuts and roughing passes, while tolerance class M provides consistent dimensional stability across batches of inserts. For job shops and production lines requiring robustness and predictable performance, this geometry reduces the chance of edge chipping and improves end-product consistency. Practical integration and application advice for the workshop This insert integrates with standard DNMG tool holders and is suitable for a wide spectrum of turning operations on steel. When selecting cutting data, favour parameters that exploit the coating’s heat resistance—moderate feeds with appropriate coolant or MQL can extend life in continuous runs. If uncertainty remains about the optimal grade or cutting data, Metav Werkzeuge provides application advice and cutting-parameter recommendations to align the insert selection with the workpiece material and machining strategy. Contact Metav Werkzeuge for tailored recommendations on the Tiger·tec Gold DNMG110404-MP5 WPP30G from Walter Tools and ensure the ideal grade and chipbreaker are selected for your steel turning applications Technical data Article number: DNMG110404-MP5-WPP30G-WALTER SKU: DNMG110404-MP5-WPP30G-WALTER Product: Drehwendeschneidplatte / indexable turning insert Designation: DNMG110404-MP5 WPP30G Series: Tiger·tec Gold Grade: WPP30G Manufacturer: Walter Tools Facts Size: 11 Thickness: 04 Shape angle: 55° Corner radius: 0.4 mm Relief angle: 0° (negative) Tolerance class: M Special features Tiger·tec Gold coating technology Coated carbide grade WPP30G MP5 chipbreaker for steel machining Suitable material group: Steel (P) Rhombic 55° insert geometry Robust cutting edge for productive machining FAQ What materials is this insert suitable for? The DNMG110404-MP5 WPP30G is specified for Steel (P) applications; the WPP30G grade and coating are optimised for unalloyed and alloyed steels. What is the benefit of the MP5 chipbreaker? The MP5 chipbreaker produces controlled, short chips during turning of steels, improving chip evacuation and contributing to a better surface finish with lower risk of built-up edge. How does the rhombic 55° geometry affect cutting? A rhombic 55° geometry balances edge strength and clearance, allowing secure engagement for heavier cuts while maintaining access to workpiece features and consistent dimensional control. Can this insert be used for finishing and roughing? Yes—the combination of WPP30G coating and the 0.4 mm corner radius supports both roughing and semi-finish operations in steel; for fine finishing, a smaller radius or specific finishing grade may be considered. Is the insert compatible with standard DNMG tool holders? The insert follows the DNMG ISO form factor and is compatible with matching DNMG tool holders designed for rhombic 55° inserts. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany
DNMG110404-NMT WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Silver coating and the robust DNMG rhombic geometry to achieve stable chip formation and long tool life when turning stainless steels and heat‑resistant alloys; order directly via Metav Werkzeuge or consult Metav Werkzeuge's technical advisers for cutting data and process optimisation. DNMG110404‑NMT WSM20S Drehwendeschneidplatte – Tiger·tec Silver, 0° negative relief, Walter Tools The DNMG110404‑NMT WSM20S is a rhombic turning insert for heavy‑duty machining of stainless steels and superalloys, combining a Tiger·tec Silver coated carbide grade with a specialised NMT chipbreaker for secure chip control. DNMG geometry Rhombus 55° for versatile turning Tiger·tec Silver coated carbide for wear resistance Suitable for stainless steel and superalloys 0° negative relief, 0.4 mm corner radius Predictable performance in difficult‑to‑cut materials The combination of a Tiger·tec Silver coating and a coated‑carbide substrate delivers high wear resistance and thermal stability in operations with poor heat conduction. For stainless steel (ISO group M) and heat‑resistant alloys (ISO group S), the grade provides more consistent chip formation and reduced risk of built‑up edge. The specialised NMT chipbreaker supports reliable evacuation of chips at moderate to heavy depths of cut, which in turn reduces downtime and the need for frequent edge dressing. This results in a measurable improvement in process stability and component surface quality. Geometry and edge design that support robust cutting The DNMG rhombic 55° shape, together with a 0.4 mm corner radius and 0° negative relief, emphasises edge strength and resistance to mechanical shock. Negative relief increases the insert’s backing support in the toolholder, making the grade suitable for interrupted cuts and heavier feed conditions where edge security is paramount. The modest corner radius balances edge resilience with a controllable cutting width, helping to maintain dimensional accuracy while extending insert life. Practical application and handling notes This insert is primarily intended for turning operations on stainless steel and high‑temperature alloys; its specification is optimised for cases where heat‑resistant performance and stable cutting edges matter. As cutting parameters depend on machine power, toolholder rigidity and coolant strategy, Metav Werkzeuge’s technical advisers can recommend starting speeds and feeds tailored to the workpiece and setup. Correctly clamped in a compatible DNMG toolholder and used with recommended cutting data, the insert will deliver predictable tool life and consistent surface finish. For application advice, grade matching or to procure the DNMG110404‑NMT WSM20S insert from Walter Tools, contact Metav Werkzeuge for expert recommendations and full order support. Technical data Article number: DNMG110404-NMT-WSM20S-WALTER Product type: Drehwendeschneidplatte Manufacturer: Walter Tools Series/grade: Tiger-tec Silver Core data Insert shape: Rhombus 55° Corner radius: 0.4 mm Relief angle: 0° (negative) Plate size: 11 Plate thickness: 04 Special features Chipbreaker: NMT Grade: WSM20S (coated carbide) Material application: S / M (superalloys, stainless steel) Tolerance class: M Execution: G Base designation: DNMG110404-NMT FAQ What materials is this insert suitable for? The DNMG110404‑NMT WSM20S insert is specified for stainless steel (ISO group M) and heat‑resistant superalloys (ISO group S), offering improved chip control and wear resistance for these demanding materials. How does the Tiger·tec Silver coating benefit machining? The Tiger·tec Silver coating on the WSM20S grade increases thermal resistance and wear protection, which helps maintain a stable cutting edge and extend tool life during continuous and semi‑continuous turning operations. What does the NMT chipbreaker do? The NMT chipbreaker is designed to support controlled chip formation and evacuation under moderate to heavy cutting conditions, reducing the likelihood of long, tangled chips and improving process reliability. Is the 0° negative relief suitable for interrupted cuts? Yes, the 0° negative relief enhances backing support for the insert, making it more robust in interrupted cuts and other operations where edge stability is critical. Can this insert be used with standard DNMG toolholders? The insert conforms to the DNMG110404‑NMT designation and is intended for use in compatible DNMG toolholders; ensure correct clamping and seating to achieve designed performance. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DNMG110408-FM5 WMP20G G Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Gold coating, the WMP20G grade and the FM5 chipbreaker for dependable stainless steel turning; reliable edge stability and consistent chip control help to secure uninterrupted production. Order the insert via Metav Werkzeuge or consult our specialists for application-specific advice. DNMG110408-FM5 WMP20G – Turning indexable insert, rhombic 55° geometry, 0° negative rake (Walter Tools) A DNMG110408-FM5 WMP20G turning insert engineered for robust stainless steel machining and optimised for secure chip formation in medium to demanding turning operations Tiger‑tec Gold coating for extended life WMP20G grade optimised for stainless steel Rhombic 55° insert with 0.8 mm radius Chipbreaker FM5 for consistent chip control Longer tool life through advanced coating and grade The combination of Tiger‑tec Gold surface technology with the WMP20G grade produces a coated carbide insert that resists wear and thermal load during prolonged turning cycles. This yields extended tool life and fewer tool changes, reducing machine downtime and overall process cost. For workshops facing variable stainless steel batches, the improved wear resistance of this system maintains a reliable edge even under intermittent high temperatures. Consistent chip control and secure cutting performance Equipped with the FM5 chipbreaker, the insert promotes predictable chip formation and evacuation, which reduces the risk of chip entanglement and protects workpiece surfaces. In practice, the chip geometry tailored to the grade leads to stable cutting forces and helps maintain finish quality on demanding stainless steel grades. The consistent chip control supports higher productivity by enabling steadier feeds and fewer interruptions. Geometry explained: why rhombic 55° and 0° rake matter The rhombic 55° shape provides a versatile cutting angle that balances strength and accessibility for external and light profiling operations. The 0° rake (negative) increases edge stability and is advantageous when cutting tougher stainless steels prone to work hardening. The 0.8 mm corner radius supports a robust cutting edge for medium-depth passes while still allowing acceptable surface finish, making the geometry suitable for general turning tasks and semi-finishing operations. Process reliability and application guidance This insert is principally suited to turning operations on stainless steel, where secure chip control and edge stability are priorities. The WMP20G grade is designed for moderate to robust cutting conditions typical of workshop and production environments. For best results, pair the insert with stable toolholders and moderate radial engagement; adapt feed and speed to the specific stainless grade to avoid excessive heat and achieve the intended tool life and surface integrity. Contact Metav Werkzeuge for tailored application advice and availability of Walter Tools DNMG110408-FM5 WMP20G inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: DNMG110408-FM5-WMP20G-WALTER Designation: DNMG110408-FM5 WMP20G Product type: Turning indexable insert Grade / series: WMP20G, Tiger‑tec Gold Manufacturer: Walter Tools Dimensional data Size: 11 Thickness: 04 Corner radius: 0.8 mm Shape: Rhombic 55° Rake angle: 0° (negative) Edge preparation: G Chipbreaker: FM5 Applications / Special features Coating / material: Coated carbide (Tiger‑tec Gold) Suited for: Stainless steel (M) Sort of application: Turning, medium to robust cutting conditions Special feature: Stable chip formation and edge security Tolerance class: M FAQ What materials is this insert designed for? This Walter Tools turning insert is specified for machining stainless steel; the WMP20G grade and chipbreaker FM5 support secure chip formation on these materials. How does the FM5 chipbreaker affect machining? The FM5 chipbreaker on this insert encourages predictable chips and smooth evacuation, which helps maintain surface finish and reduces interruptions in turning operations. When is a 0° (negative) rake preferable? A 0° rake is chosen when increased edge resilience is needed; it is beneficial for tougher stainless steels and situations where a robust cutting edge reduces the likelihood of built-up edge. Can the rhombic 55° shape be used for profiling? Yes, the rhombic 55° geometry provides access for external turning and light profiling while keeping adequate strength for semi-finishing passes. What does the "04" in thickness indicate? The thickness designation "04" refers to the insert thickness specified by the standard product code and should be checked against toolholder compatibility before use. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen, Germany Protected brand names and trademarks are the property of their respective owners. Brand names and trademarks are mentioned for explanatory purposes only; there is no affiliation between our company and the referenced brands. The offered item is an original, factory-new product from the stated manufacturer.
DNMG110408-FM5 WMP20S WMP20S Wendeplatten - Walter Tools
Take advantage of the combination of a wear-resistant Tiger·tec Silver coating and the WMP20S carbide grade for secure chip formation when machining stainless steel; the rhombic 55° geometry and FM5 chipbreaker ensure reliable turning performance. Order via Metav Werkzeuge or contact the consultants for application advice. DNMG110408-FM5 WMP20S turning insert — Tiger·tec Silver, for stainless steel | Walter Tools The DNMG110408-FM5 WMP20S is a rhombic 55° turning insert designed for turning applications on stainless steel in medium to robust cutting conditions. Tiger·tec Silver coating for wear resistance FM5 chipbreaker for secure chip control Suitable for stainless steel (ISO M) Rhombic 55° geometry for versatile turning Consistent performance for stainless-steel turning The combination of the WMP20S cutting grade and the Tiger·tec Silver coating delivers improved resistance to the abrasive and adhesive wear typical of machining stainless steel. The coated cemented-carbide substrate supports a stable cutting edge, which reduces the risk of built-up edge and helps maintain component tolerances over longer production runs. This stability translates into fewer interruptions for tool changes and more predictable process windows in serial and batch production. Controlled chips and reliable surface quality Equipped with the FM5 chipbreaker and a rhombic 55° form, the insert promotes predictable chip formation and evacuation under medium to robust conditions. The geometry and chip control work together to lower the chance of chip entanglement and protect the workpiece surface, resulting in a consistent surface finish and reduced secondary operations. For machining centres and lathes where uptime and repeatability matter, this results in measurable productivity gains. Easy integration into production processes The neutral to negative rake condition (0° negative) and a corner radius of 0.8 mm offer a balance between edge robustness and dimensional control. The insert’s form and grade are suitable for a variety of turning tasks on stainless steel, from light profiling to heavier roughing cuts. Straightforward toolholder compatibility and the proven Tiger·tec Silver series make this insert an efficient choice when standardising tool inventories across machining cells. For applications requiring a resilient, stainless-steel-capable insert, specify the Tiger·tec Silver WMP20S grade from Walter Tools and consult Metav Werkzeuge for cutting-data recommendations and availability — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: DNMG110408-FM5-WMP20S-WALTER Designation: DNMG110408-FM5 WMP20S Manufacturer: Walter Tools Product type: Turning insert (rhombic) Series: Tiger·tec Silver Grade: WMP20S Chipbreaker: FM5 Specifications Plate size code: 11 Plate thickness code: 04 Corner radius: 0.8 mm Rake angle: 0° (negative) Special features Coating: Tiger·tec Silver Shape: Rhombus 55° Suitable material group: stainless steel (ISO M) Insert family: DNMG Application focus: medium to robust turning FAQ What materials is this insert mainly intended for? The DNMG110408-FM5 WMP20S insert from Walter Tools is primarily intended for stainless steel machining (ISO M), designed to promote secure chip formation under medium to robust conditions. How does the FM5 chipbreaker benefit production? The FM5 chipbreaker on the DNMG110408-FM5 helps generate short, controllable chips, which improves chip evacuation and contributes to consistent surface quality during turning operations with the WMP20S grade. Is the insert suitable for finishing and roughing operations? Yes; the rhombic 55° geometry combined with a 0.8 mm corner radius and the robust WMP20S grade makes this Walter Tools insert adaptable for both finishing and heavier turning passes on stainless steel. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen The Walter AG (brand appearance: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and forms part of a worldwide toolmaking group. Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only; there is no affiliation between Metav Werkzeuge and the listed manufacturers. The offered article is an original, factory-new product of the manufacturer.
DNMG110408-FM5 WSM10S WSM10S Wendeplatten - Walter Tools
Take advantage of the combination of a heat-resistant Tiger·tec Silver grade, a stabilising FM5 chipbreaker and a robust rhombic 55° geometry for reliable turning of demanding materials; order the insert directly via Metav Werkzeuge or request application advice from the consultants. DNMG110408-FM5 WSM10S — indexable turning insert for rostfreier Stahl and superalloys, Walter Tools The DNMG110408-FM5 WSM10S is a coated carbide indexable insert designed for demanding turning operations on rostfreier Stahl and heat-resistant superalloys, combining a Tiger·tec Silver grade with an FM5 chipbreaker for process security Tiger·tec Silver coating for heat resistance Optimised FM5 chipbreaker for stable chips Rhombic 55° form for versatile turning 0.8 mm corner radius for edge strength High-performance grade for demanding materials The insert employs the WSM10S grade from the Tiger·tec Silver series, a coated carbide technology engineered to withstand elevated temperatures and abrasive wear. This composition supports stable cutting edges when machining rostfreier Stahl and heat-resistant alloys, reducing the frequency of edge changes and improving cycle-time reliability. The material combination is particularly beneficial where heat generation and built-up edge formation are common challenges, offering a durable balance between wear resistance and toughness. Reliable chip control and cutting geometry for consistent results Equipped with the FM5 chipbreaker, this indexable insert promotes reproducible chip formation and evacuation, which simplifies swarf handling and minimises machining interruptions. The rhombic 55° insert shape provides flexibility across turning tasks, while the 0.8 mm corner radius increases edge strength for interrupted cuts and tougher feeds. The negative 0° free angle geometry contributes to a robust cutting posture suitable for heavier cuts and unstable workpiece surfaces, supporting process stability without sacrificing surface quality. Industrial integration and practical benefits on the shopfloor The insert’s form and grade make it suitable for productive turning setups in jobbing and series production, where repeatable component quality and reduced tool-change time are priorities. The geometry and coating combination helps maintain a predictable tool life, which supports planning for tooling inventories and minimises unplanned downtime. For toolroom engineers and production managers, the result is improved throughput and a more consistent surface finish on challenging batches of rostfreier Stahl and superalloys. For reliable high-temperature performance and predictable chip control, order genuine Walter Tools DNMG110408-FM5 WSM10S inserts from Metav Werkzeuge or request tailored cutting data via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: DNMG110408-FM5-WSM10S-WALTER Article designation: DNMG110408-FM5 WSM10S Product type: indexable turning insert Manufacturer: Walter Tools Core specifications Insert size: 11 mm Thickness: 04 Corner radius: 0.8 mm Free angle: 0° (negative) Tolerance class: M Design & features Grade: WSM10S Series: Tiger·tec Silver Chipbreaker: FM5 Shape: Rhombus 55° Coated carbide Material suitability: S / M (rostfreier Stahl and heat-resistant superalloys) Execution: G FAQ What materials is this insert intended for? The DNMG110408-FM5 WSM10S insert is intended for machining rostfreier Stahl and heat-resistant superalloys (material groups S and M). Which chipbreaker is fitted and what is its benefit? This insert features the FM5 chipbreaker, which promotes stable chip formation and eases chip evacuation during turning operations. How does the Tiger·tec Silver grade affect tool life? The Tiger·tec Silver grade on the DNMG110408-FM5 WSM10S provides enhanced heat resistance and wear control, contributing to longer edge life under high-temperature machining. What turning applications suit the rhombic 55° shape best? The rhombic 55° form is versatile and well suited for general turning, profiling and shoulder operations where access and finish quality are required. Manufacturer: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered item is an original, factory-new product of the manufacturer.
DNMG110408-FM5 WSM20S WSM20S Wendeplatten - Walter Tools
Take advantage of the combination of Tiger·tec Silver coating and the WSM20S grade for secure chip control in demanding materials; the negative 0° geometry and FM5 chipbreaker deliver process stability and repeatable edge life. Order the insert directly via Metav Werkzeuge or contact the consultants for application-specific recommendations. DNMG110408-FM5 WSM20S turning insert — Walter Tools, Tiger·tec Silver, FM5 chipbreaker DNMG110408-FM5 WSM20S is a coated turning insert designed for heavy-duty machining and reliable performance in difficult-to-cut alloys Tiger·tec Silver coating for high thermal resistance FM5 chipbreaker for controlled chip formation Suitable for rostfreier Stahl and superalloys Rhombic 55° shape for versatile turning applications Consistent cutting performance for demanding alloys The insert offers a coated carbide substrate in the WSM20S grade, engineered for applications where heat resistance and edge stability are essential. The combination of the Tiger·tec Silver technology and the FM5 chipbreaker promotes predictable chip formation and reduces the risk of built-up edge when machining rostfreier Stahl or heat-resistant superalloys. This translates into fewer interruptions and higher effective machine utilisation. The negative 0° geometry supports secure engagement and steady cutting forces on medium to heavy interrupted cuts. Geometry and handling that improve process reliability With a rhombic 55° form and a corner radius of 0.8 mm, the insert balances strength and surface finish. The plate thickness 04 and the dimension code 11 make the component robust enough for roughing while still enabling acceptable surface quality for semi-finishing passes. The FM5 chipbreaker is tuned to the insert geometry to break chips reliably across the specified material groups, which reduces toolholder and machine downtime and simplifies chip management in production environments. Clear application guidance and benefits for production planning Assigned to material groups S / M, the grade is suitable for both heat-resistant superalloys and rostfreier Stahl, where thermal load and edge wear are critical factors. The coated grade supports higher cutting parameters compared with conventional uncoated grades, offering an improved cost-per-cut scenario and longer intervals between indexings. When integrated into a well-structured cutting strategy, the insert contributes to reproducible component quality and predictable tool life, aiding production planning and process stability across batches. For machining applications requiring high thermal stability and secure chip control, consult Metav Werkzeuge about availability and optimal cutting parameters for this Walter Tools Tiger·tec Silver insert Technical data Article number: DNMG110408-FM5-WSM20S-WALTER Designation: DNMG110408-FM5 WSM20S Brand: Walter Tools Series: Tiger-tec Silver Facts Plate size: 11 Corner radius: 0.8 mm Plate thickness: 04 Relief angle: 0° (negativ) Tolerance class: M Special features Grade: WSM20S Chipbreaker: FM5 Plate shape: Rhombus 55° Applicable material groups: S / M Product type: Turning insert FAQ What materials is this insert intended for? The DNMG110408-FM5 WSM20S insert from Walter Tools is specified for material groups S and M, i.e. heat-resistant superalloys and rostfreier Stahl, optimised for secure chip control and edge stability. How does the FM5 chipbreaker affect machining? The FM5 chipbreaker on this Walter Tools insert promotes controlled chip segmentation and evacuation, reducing the likelihood of entangling chips and improving surface consistency during turning operations. What advantages does the Tiger·tec Silver coating offer? The Tiger·tec Silver coating increases thermal resistance and wear protection on the cutting edge, enabling higher cutting parameters and longer intervals between indexings when machining demanding alloys. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Walter AG (trading as Walter Tools) is among the world’s leading manufacturers of precision tools for metalworking. Protected brand names and trademarks are the property of their respective owners and are mentioned here exclusively for explanation. There is no affiliation between our company and the named brands; the offered item is an original, factory-new product of the manufacturer.
DNMG110408-FP5 WEP10C WEP10C Wendeplatten - Walter Tools
Take advantage of the combination of Walter Cermet cutting performance and the proven WEP10C cermet grade for stable chip formation and consistent surface quality; the FP5 chipbreaker and rhombic geometry deliver predictable cutting behaviour while the 0° negative rake reduces cutting forces—order the insert directly via Metav Werkzeuge or consult our specialists for application matching. DNMG110408-FP5 WEP10C indexable turning insert by Walter Tools — rhombic 55°, FP5 chipbreaker DNMG110408-FP5 WEP10C is an indexable turning insert designed for medium to fine finishing and stable machining in a wide range of materials using a cermet cutting grade. Walter Cermet grade WEP10C FP5 chipbreaker for stable chips Rhombic 55° geometry for versatile turning 0° negative rake for reduced cutting force High-performance finishing and reliable chip control The combination of WEP10C cermet and the FP5 chipbreaker delivers a balance between wear resistance and edge strength, making this insert suitable for finishing operations that demand consistent surface quality. The rhombic 55° shape provides versatile approach angles for external turning and light profiling, while the 0.8 mm corner radius helps maintain dimensional stability on short to medium overhangs. In practical terms, this means fewer interruptions for edge changes and a steadier process capability on production runs. Material design and machining behaviour explained The Walter Cermet composition used in this grade improves high-temperature hardness and reduces crater wear compared with conventional carbide grades. The 0° negative rake changes the cutting geometry to lower biting tendency and dampen vibrations during cuts with small depths of cut. For engineers unfamiliar with cermet terminology: cermet is a ceramic-metal composite that combines hardness and thermal resistance from ceramics with toughness from metallic binders, resulting in improved finish and longer life in finishing passes. Where this insert adds the most value on the shopfloor With its rhombic geometry and moderate 0.8 mm corner radius, the insert is suited to finishing of shafts, shoulders and turned faces where dimensional accuracy and surface finish are priorities. The FP5 chip control pattern supports stable, short chips in interrupted and continuous cuts, reducing the risk of built-up edge and improving tool life. Process planners will find that the insert’s features reduce the need for downstream grinding or polishing on many parts, accelerating throughput on repeat batches. Practical handling and toolholder compatibility The designation indicates a standard DNMG seat, enabling straightforward integration into existing toolholders that accept rhombic 55° negative inserts. The insert thickness and form follow industry coding for easy stocking and replacement; the tolerance class M supports consistent seat fit and repeatability. For best results, match the insert to a clamping system that ensures minimal chatter and confirm cutting parameters with the machine tool’s rigidity and spindle power in mind. Contact Metav Werkzeuge today to discuss suitable cutting parameters for Walter Tools inserts or to request assistance matching the DNMG110408-FP5 WEP10C to specific material and toolholder combinations; eMail: info@metav-werkzeuge.com, Tel: +49 2822 7131930 Technical data Article number: DNMG110408-FP5-WEP10C-WALTER Designation: DNMG110408-FP5 WEP10C Series: Walter Cermet Grade: WEP10C Manufacturer: Walter Tools Facts Shape: Rhombus 55° Size: 11 Thickness: 04 Corner radius: 0.8 mm Clearance / rake: 0° (negative) Tolerance class: M Special features Chipbreaker: FP5 Material type: Cermet grade Execution: G Insert type: Indexable turning insert Suitable for finishing and light profiling FAQ What materials is this insert designed for? The DNMG110408-FP5 WEP10C insert uses the WEP10C cermet grade and FP5 chipbreaker to suit a broad range of finishing applications; material suitability should be verified against the Walter Cermet product matrix for optimal selection. How does the 0° negative rake affect machining? A 0° negative rake on this insert reduces cutting bite and tends to stabilise the cutting edge under finishing conditions, which can lower vibration and improve surface finish when using the DNMG110408-FP5 WEP10C in short overhang setups. Which toolholders are compatible with this insert profile? The rhombic 55° form and DNMG designation are standard for indexable turning toolholders that accept negative rhombic inserts; confirm clamping style and seat fit before assembly. What benefits does the WEP10C cermet grade provide? WEP10C enhances high-temperature hardness and wear resistance compared with typical carbides, offering improved surface finish and extended edge life in finishing operations when using this Walter Tools insert. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Die Walter AG (brand appearance: Walter Tools) is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and trade names are the property of their respective owners. Mark names and protected product designations are used for explanation only; there is no affiliation between our company and the named manufacturers. The offered article is an original, factory-new product of the manufacturer.
DNMG110408-FP5 WKP01G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and the WKP01G grade for long tool life and consistent chip control in steel and cast iron turning; the rhombic 55° geometry and 0.8 mm corner radius further improve surface quality and cutting security. Order the insert directly via Metav Werkzeuge or ask the consultants for application advice. DNMG110408-FP5 WKP01G indexable turning insert – Rhomb 55°, Tiger‑tec Gold (Walter Tools) A DNMG110408-FP5 WKP01G indexable turning insert designed for precision turning of steel and cast iron, combining a Tiger‑tec Gold coating with an FP5 chipbreaker for reliable chip control and extended tool life Tiger‑tec Gold coating for high wear resistance Suitable for steel (P) and cast iron (K) machining Rhomb 55° geometry for versatile turning operations 0.8 mm corner radius with 0° negative relief Increased process reliability through advanced coating and grade The combination of the Tiger‑tec Gold coating and the WKP01G grade yields excellent wear resistance and consistent edge stability under thermal load. Designed for both steel and cast iron (ISO groups P and K), the insert resists abrasive wear and maintains cutting performance during extended cycles. The specialised coating also reduces adhesive build-up, which improves repeatability and reduces unplanned rework. For production environments that prioritise uptime, this means fewer indexings and steadier component tolerances. Geometry and chip control that improve surface finish The Rhomb 55° shape and FP5 chipbreaker deliver a balance between strength and accessibility at various cutting depths. A 0.8 mm corner radius supports a robust cutting edge that reduces the tendency to form chatter while still enabling fine surface finishes. The negative relief at 0° increases edge strength for heavier cuts and interrupted turning. Together, these geometry choices translate into more reliable finishing passes and reduced need for secondary operations, boosting throughput without compromising component quality. Compatibility and practical benefits for workshop integration Marked as DNMG110408-FP5 and supplied in tolerance class M, the insert fits standard DNMG toolholders and can be indexed quickly to restore cutting performance. The FP5 chipbreaker is optimised for medium to stable chip forms, which simplifies chip evacuation in automated setups. With predictable flank wear and stable cutting conditions, tool change intervals become easier to schedule, supporting leaner inventory and more efficient production planning. The overall result is a cost-effective, easy-to-integrate solution for mixed batches of steel and cast iron parts. For reliable productivity with the Tiger‑tec Gold WKP01G inserts, contact Metav Werkzeuge for availability and tailored cutting recommendations on the DNMG110408-FP5 WKP01G insert Technical data Article number: DNMG110408-FP5-WKP01G-WALTER Designation: DNMG110408-FP5 WKP01G Product type: Indexable turning insert Brand: Walter Tools Series: Tiger‑tec Gold Facts Geometry: Rhombus 55° Corner radius: 0.8 mm Relief angle: 0° (negative) Chipformer: FP5 Size: 11 Thickness: 04 Tolerance class: M Material grade: P / K Special features Coating: Tiger‑tec Gold Grade: WKP01G (coated carbide) Application: Steel and cast iron machining Robust edge for interrupted cuts Stable chip control for automated turning FAQ What materials is this insert suitable for? The DNMG110408-FP5 WKP01G insert is suitable for machining steel (P) and cast iron (K), reflecting the WKP01G grade design for both material groups. Which toolholders are compatible with this insert? This indexable insert follows the DNMG designation and fits standard DNMG toolholders that accept rhombic 55° turning inserts. How does the FP5 chipbreaker affect cutting performance? The FP5 chipbreaker promotes controlled chip formation and evacuation under typical turning conditions, improving process security and reducing the risk of chip entanglement. When should the insert be indexed or replaced? Indexing or replacement is recommended when flank wear or edge chipping visibly affects surface finish or dimensional accuracy; routine inspection intervals depend on component tolerances and machining conditions. Is this insert suitable for interrupted cuts? Yes, the combination of a 0° negative relief and a 0.8 mm corner radius provides increased edge strength for interrupted or heavy cuts. The Walter AG (branded as Walter Tools) with headquarters in Tübingen is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik group. Protected trademarks and trade names are the property of their respective owners and are mentioned for explanatory purposes only; there is no affiliation between Metav Werkzeuge and the named manufacturers, and the items offered are original, brand‑new products of the respective manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DNMG110408-FP5 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of the combination of the Tiger‑tec Gold coating and the proven FP5 chipformer for reliable, economical steel turning; the rhombic 55° geometry and 0.8 mm corner radius ensure stable cuts and predictable surface quality. Order the insert directly via Metav Werkzeuge or contact our consultants for machining advice. DNMG110408-FP5 WPP10G — Turning insert for steel (Walter Tools) DNMG110408-FP5 WPP10G is a rhombic 55° indexable turning insert with Tiger‑tec Gold coating, engineered for robust and efficient machining of steel. Tiger‑tec Gold coating for extended tool life Rhombic 55° shape for versatile turning operations 0.8 mm corner radius for stable chip control Negative 0° rake for robust cutting performance Longer tool life through advanced coating technology The coated carbide grade WPP10G, part of the Tiger‑tec Gold family, provides improved wear resistance and predictable abrasion behaviour during continuous turning of steels (ISO P). This coating technology reduces flank wear and helps maintain cutting edge integrity over longer tool life, which lowers tool-change frequency and increases machine uptime. The result is a cost-effective balance between performance and lifetime that supports higher productivity in everyday production. Stable cutting geometry for consistent surface quality The rhombic 55° geometry combined with a 0.8 mm corner radius and the FP5 chipformer produces controlled chip formation and stable cutting forces when machining a wide range of steels. The negative 0° relief angle contributes to a robust cutting edge that resists edge chipping under interrupted cuts or tougher turning tasks. This geometry leads to repeatable surface finishes and dimensional stability, particularly where process reliability is a priority. Simple identification and integration into tool systems Marked with the ISO designation DNMG110408‑FP5 WPP10G, the insert is easy to match with standard clamping systems and toolholders used in turning centres. The tolerance class M ensures a consistent fit and positioning accuracy, so changeovers are fast and reproducible. The coded dimensions and chipbreaker type enable straightforward programming and process planning for series production or batch machining. Practical benefits for day‑to‑day turning operations With a compact insert size and a clearly specified thickness code, this indexable insert supports efficient stock removal and predictable wear behaviour across a broad range of steel grades. The FP5 chipbreaker reduces the need for complex coolant strategies in many steel applications and helps maintain a stable cutting zone. Overall, the design aims to reduce unplanned downtime and deliver steady part quality with manageable tool inventories. Contact Metav Werkzeuge for tailored machining recommendations on Walter Tools turning solutions such as the DNMG110408‑FP5 WPP10G, or request supply and delivery details via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: DNMG110408-FP5-WPP10G-WALTER Article name: DNMG110408-FP5 WPP10G Manufacturer: Walter Tools Product type: Turning insert Facts Corner radius: 0.8 mm Relief angle: 0° (negative) Insert shape: Rhombus 55° Insert size: 11 Thickness code: 04 Tolerance class: M Special features Grade: WPP10G Coating technology: Tiger‑tec Gold Chipformer: FP5 Material suitability: P (steel) ISO designation: DNMG110408‑FP5 WPP10G FAQ What materials is this insert suitable for? The DNMG110408‑FP5 WPP10G is designed primarily for steel (ISO group P); the WPP10G grade and Tiger‑tec Gold coating are optimised for the heat and chip characteristics typical of steel machining. How does the FP5 chipbreaker affect performance? The FP5 chipformer provides consistent chip control and reduces cutting forces during turning; in the DNMG110408‑FP5 WPP10G this contributes to stable cutting and improved surface quality for a range of steel grades. What advantages does Tiger‑tec Gold offer? Tiger‑tec Gold coating improves wear resistance and edge stability under the thermal and mechanical loads of steel turning, extending tool life and enabling more predictable process windows with the DNMG110408‑FP5 WPP10G insert. What does the 0.8 mm corner radius mean for my parts? A 0.8 mm corner radius balances edge strength and the achievable surface finish; it helps prevent edge chipping while delivering a consistent profile on turned components. Protected trademarks and trade names are the property of their respective owners. Mark names and protected product designations are mentioned for explanation only. There is no affiliation between our company and the named manufacturers. The offered item is an original, factory‑new product of the manufacturer. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen
DNMG110408-FP5 WPP10S WPP10S Wendeplatten - Walter Tools
Benefit from the combination of Tiger‑tec Silver coating and a dedicated FP5 chipbreaker for consistently productive Stahl turning; the geometry and 0.8 mm corner radius deliver stable cutting and predictable tool life. Order the insert via Metav Werkzeuge or request expert application advice from our consultants. DNMG110408-FP5 WPP10S indexable turning insert, Tiger‑tec Silver, for Stahl — Walter Tools The DNMG110408-FP5 WPP10S is a rhombic 55° coated carbide insert engineered for efficient, general-purpose turning of Stahl components in production environments. Tiger‑tec Silver coating for long tool life Optimised FP5 chipbreaker for Stahl turning Rhombic 55° form for versatile operations 0.8 mm corner radius for stable cutting edge Consistent productivity through optimised coating and grade The insert combines the Tiger‑tec Silver surface technology with the WPP10S grade to provide a reliable balance between wear resistance and toughness. This pairing reduces flank wear and maintains a sharper cutting edge for longer, which translates into fewer tool changes and improved cycle-time reliability. The description of the grade indicates a focus on Stahl machining, so users can expect controlled heat management and robust performance when machining unalloyed and alloyed Stahl. Improved chip control for safer, efficient turning Equipped with the FP5 chipbreaker, the insert is shaped to break and evacuate chips effectively during medium‑to‑general turning operations. Chipformers designed for Stahl help avoid long, stringy chips and support consistent surface finish. For workshops without advanced chip management systems, the chip control provided by this geometry lowers the risk of rework and stoppages, making the machining process more efficient and easier to supervise. Geometry and edge stability for repeatable results The rhombic 55° form with a 0.8 mm corner radius and a negative 0° rake offers a stable cutting edge for a range of turning tasks. The DNMG form provides good access to shoulder cuts and profiling, while the modest corner radius balances edge strength and surface quality. In practice, this means the insert supports repeatable dimensional control and predictable wear patterns in serial production, reducing inspection variability and improving first‑pass yield. Practical compatibility and handling in the toolroom Available in the DNMG110408-FP5 ISO designation, the insert fits standard toolholders for DNMG‑style plates and is intended for general Stahl applications. Its coated carbide construction and defined tolerance class ensure interchangeability and process consistency across tool changes. For customers assessing tooling setups, the insert is a practical option where reliable, versatile performance is required rather than a specialised micro‑geometry for exotic alloys. For availability, application guidance or batch supply of Walter Tools DNMG110408-FP5 WPP10S inserts contact Metav Werkzeuge — phone +49 2822 7131930 or email info@metav-werkzeuge.com for tailored machining advice. Technical data Article number: DNMG110408-FP5-WPP10S-WALTER Designation: DNMG110408-FP5 WPP10S Manufacturer: Walter Tools Product type: indexable turning insert Numbers / Core technical data Insert size: 11 mm Thickness: 4 mm Corner radius: 0.8 mm Insert form: Rhombus 55° Rake angle: 0° (negative) Tolerance class: M Designs / Special features Series: Tiger‑tec Silver Grade: WPP10S (coated carbide) Chipbreaker: FP5 Execution/geometry: G Material application: Stahl FAQ What materials is this insert suitable for? The DNMG110408-FP5 WPP10S is designed primarily for machining Stahl; the WPP10S grade and FP5 chipbreaker are optimised for unalloyed and alloyed Stahl workpieces. Is the insert compatible with standard DNMG toolholders? Yes, the DNMG110408-FP5 designation matches standard DNMG toolholders and clamping systems for indexable turning plates. How does the Tiger‑tec Silver coating benefit production? The Tiger‑tec Silver coating on the WPP10S grade enhances wear resistance and thermal stability, extending tool life and maintaining surface quality during extended Stahl turning operations. What cutting tasks suit the 0.8 mm corner radius? A 0.8 mm corner radius offers a compromise between edge strength and finish quality, making the insert suitable for general finishing and medium stock‑removal turning on Stahl components. Can the insert be used for high‑feed or heavy interrupted cuts? The geometry and negative rake provide edge robustness for many general turning tasks, but for heavy interrupted cutting specialised grades and geometries should be evaluated; consult Metav Werkzeuge for application‑specific recommendations. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Geschützte Markenzeichen und Warenbezeichnungen liegen im Recht ihrer jeweiligen Eigentümer. Markennamen und geschützte Warenzeichen werden ausschließlich zu Erklärungszwecken genannt. Es besteht keinerlei Verbindung zwischen unserem Unternehmen und den genannten Marken. Es handelt sich bei dem angebotenen Artikel um originale fabrikneue Waren des Herstellers.
DNMG110408-FP5 WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of a Tiger‑tec Gold coated grade and an effective FP5 chipbreaker to secure consistent performance in steel turning operations; order directly via Metav Werkzeuge or consult the team for grade and holder recommendations. DNMG110408-FP5 WPP20G turning insert — for steel machining, Tiger‑tec Gold, Walter Tools The DNMG110408-FP5 WPP20G is a coated carbide turning insert engineered for reliable steel machining, offering a balanced mix of wear resistance and toughness for general turning applications. Tiger‑tec Gold coating technology Optimised FP5 chipbreaker Rhombic 55° geometry 0.8 mm corner radius Negative 0° relief angle Consistent metal removal through Tiger‑tec Gold performance The Tiger‑tec Gold grade WPP20G provides a coated carbide composition that is optimised for the thermal and tribological challenges of machining steel. Its surface treatment increases resistance to flank and crater wear, which translates into longer periods between tool changes and more predictable tool life. For production environments where process stability and repeatable component quality matter, the combination of a robust grade and an engineered coating ensures reliable cutting behaviour and helps maintain dimensional consistency across batches. Predictable chip control and reliable edge security The FP5 chipbreaker is designed specifically to shape and evacuate chips when turning steels of the ISO P group. Paired with the rhombic 55° geometry and a 0.8 mm corner radius, the insert supports stable cutting forces and good surface integrity on workpieces. The negative 0° relief angle creates a stronger cutting edge suited to heavier cuts and interrupted cuts where edge security is essential. These features reduce the risk of unexpected edge failure and contribute to smoother finishing cycles with fewer rejects. Design choices that support productivity and tool management With the DNMG form factor and the WPP20G grade, workshop logistics benefit from a broadly applicable insert that covers a wide range of steel severities — from tougher to more wear‑resistant situations. The insert thickness and format ensure compatibility with common DNMG toolholders, simplifying inventory planning. For teams assessing process economics, the predictable wear behaviour and broad material coverage of this grade help optimise tool rotations and lower overall machining costs while preserving component quality. If further clarification on fitment or application limits is required, technical documentation and advice are available; Metav Werkzeuge can assist with matching inserts to suitable toolholders and process parameters for specific steel alloys. Consult Metav Werkzeuge for tailored recommendations on Walter Tools grades and holder compatibility to optimise steel turning performance with DNMG110408-FP5 WPP20G Technical data Article number: DNMG110408-FP5-WPP20G-WALTER Designation: DNMG110408-FP5 WPP20G Series: Tiger‑tec Gold Grade: WPP20G Chipbreaker: FP5 Numbers / core technical data Plate size: 11 Corner radius: 0.8 mm Plate thickness: 04 Relief angle: 0° (negative) Tolerance class: M Designs / special features Coated carbide Rhombic 55° geometry Optimised chip control for steel (ISO P) Execution: G Suitable for steel machining FAQ Is this insert suitable for general steel turning tasks? Yes. The DNMG110408-FP5 WPP20G is specified for machining steels (ISO P) and the WPP20G Tiger‑tec Gold grade is formulated for the heat and chip formation typical of steel turning. What advantages does the FP5 chipbreaker offer in daily production? The FP5 chipbreaker on this insert provides controlled chip formation and evacuation for steel applications, improving surface quality and reducing the likelihood of chip interference during continuous turning. Can the DNMG110408-FP5 WPP20G be used for interrupted cuts? The negative 0° relief and robust coated carbide construction of the DNMG110408-FP5 WPP20G give it enhanced edge strength, making it more tolerant to interrupted cuts compared with more fragile geometries. How does the Tiger‑tec Gold coating influence tool life? The Tiger‑tec Gold coating enhances wear resistance and edge stability under the thermal loads of steel turning, resulting in longer, more predictable tool life for the WPP20G grade. Is this insert compatible with standard DNMG toolholders? Yes. The DNMG form factor matches standard DNMG clamping systems; confirmation of seat size and clamping torque should be made against the toolholder manufacturer’s specifications. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen The Walter AG (brand presentation: Walter Tools), headquartered in Tübingen, is one of the world’s leading manufacturers of precision tools for metalworking and is part of the Swedish Sandvik Group. Protected trademarks and brand names are the property of their respective owners. Brand names and protected trademarks are mentioned for explanatory purposes only. There is no connection between our company and the mentioned brands. The offered article is original, factory‑new goods from the manufacturer.
DNMG110408-FW5 WKP01G WKP01G Wendeplatten - Walter Tools
Benefit from the Tiger·tec Gold coating and the WKP01G grade for improved edge stability and extended tool life; the FW5 chipbreaker together with the rhombic 55° form and 0.8 mm corner radius enables consistent chip control when machining steel and cast iron. Order the DNMG110408-FW5 WKP01G directly via Metav Werkzeuge or consult our technical team for tailored cutting data. DNMG110408-FW5 WKP01G — Turning insert, Tiger·tec Gold (Walter Tools) A DNMG110408-FW5 WKP01G turning insert designed for reliable roughing and finishing of steel and cast iron components, offering durable coated carbide performance. Tiger·tec Gold coating for extended tool life WKP01G grade optimised for steel and cast iron FW5 chipbreaker for controlled chip formation Rhombic 55° form with 0.8 mm corner radius High productivity through advanced coating and grade The combination of the Tiger·tec Gold coating with the WKP01G carbide grade delivers a balance of wear resistance and edge stability that supports longer tool life under continuous production conditions. Because the coating reduces abrasive wear and the grade is formulated for the thermal and mechanical characteristics of steel and cast iron, the insert maintains cutting performance across mixed batch runs. This results in fewer tool changes and a more predictable production rhythm, improving overall machine utilisation without sacrificing surface quality. Geometry engineered for consistent chip control and versatility With a rhombic 55° geometry and a clearly defined 0.8 mm corner radius, the insert provides a stable cutting edge for a variety of turning tasks. The FW5 chipbreaker is designed for controlled chip formation, helping to avoid long, entangling chips in both forged steels and abrasive cast irons. The negative 0° relief angle supports secure clamping and enables robust cuts; the specific geometry is therefore suitable for both semi-finishing and finishing operations where dimensional stability and repeatability are required. Clear material suitability and process benefits Certified for use with material groups P (steel) and K (cast iron) according to ISO classification, the insert provides reliable performance across the most commonly encountered workpiece materials in general engineering workshops. The result is improved cycle times and consistent component quality when machining a mix of unalloyed, alloyed steels and grey or nodular cast iron. Selecting this insert reduces the need for multiple specialised grades, supporting a simplified tooling portfolio and faster setup times. Practical information on tolerances and form The insert is supplied in the rhombic 55° form with the listed tolerance class M, ensuring interchangeability within standard toolholders and stable positional repeatability. The plate size indicator and thickness code are specified for correct seating in compatible toolholders; the ISO designation and series allow straightforward matching with existing cutting data. Where required, technicians can consult the manufacturer series data to determine optimum cutting speeds and feeds for specific workpiece alloys. For robust, high‑productivity turning in steel and cast iron, specify the Walter Tools Tiger·tec Gold grade DNMG110408-FW5 WKP01G via Metav Werkzeuge for fast supply and application support—contact Metav Werkzeuge for cutting data and availability at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: DNMG110408-FW5-WKP01G-WALTER Product: DNMG110408-FW5 WKP01G Manufacturer: Walter Tools Series: Tiger·tec Gold Facts Plate size: 11 Thickness code: 04 Corner radius: 0.8 mm Relief angle: 0° (negative) Tolerance class: M Special features Grade: WKP01G Chipbreaker: FW5 Insert form: Rhombic 55° Material suitability: Steel (P) and cast iron (K) ISO designation: DNMG110408-FW5 WKP01G FAQ What materials is this insert suitable for? The DNMG110408-FW5 WKP01G is designed for steel (P) and cast iron (K) applications; the WKP01G grade and Tiger·tec Gold coating provide abrasion resistance and thermal stability for these material groups. How does the FW5 chipbreaker affect machining? The FW5 chipbreaker promotes controlled chip formation, reducing the risk of long, tangled chips and improving process stability when turning a variety of steels and cast irons. Is the insert compatible with standard DNMG toolholders? Yes, the ISO designation DNMG110408-FW5 WKP01G corresponds to common DNMG toolholders; the tolerance class M ensures positional repeatability for standard clamping systems. What benefits does the Tiger·tec Gold coating offer? The Tiger·tec Gold coating increases wear resistance and edge life, enabling higher productivity and fewer insert changes in continuous production environments. What cutting tasks is the 0.8 mm corner radius suited to? A 0.8 mm corner radius provides a compromise between strength and surface finish, making it suitable for both semi‑finishing and finishing operations where a robust edge and good surface quality are required. Walter Tools: Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. The referenced brand is mentioned for explanatory purposes only; no affiliation between Metav Werkzeuge and the brand is implied. The offered item is an original, factory‑new product of the manufacturer.
DNMG110408-FW5 WPP10G WPP10G Wendeplatten - Walter Tools
Take advantage of the Tiger·tec Gold coating and the WPP10G carbide grade together with the FW5 chipbreaker for consistent chip control and productive steel turning; order the DNMG110408-FW5 WPP10G directly via Metav Werkzeuge or contact our consultants for application support. DNMG110408-FW5 WPP10G indexable turning insert – optimised for steel, Walter Tools The DNMG110408-FW5 WPP10G is a rhombic 55° indexable turning insert designed for reliable, high-productivity turning of steel components in industrial machining environments. Tiger·tec Gold coating for enhanced wear resistance Optimised for steel (P) turning applications FW5 chipbreaker for secure chip control Rhombic 55° geometry with 0.8 mm corner radius Increased process stability and longer tool life through coating technology The combination of the Tiger·tec Gold coating and the WPP10G carbide grade provides a balance of wear resistance and toughness that translates into longer tool life and fewer interruptions in production. The advanced coating reduces flank wear under the thermal and mechanical loads typical of steel machining, while the substrate retains edge stability during moderate interrupted cuts. This results in improved component consistency and reduced tool change frequency, supporting efficient shop-floor scheduling and predictable cycle times. Precise chip control and surface quality with FW5 chipbreaker Equipped with the FW5 chipbreaker, this insert promotes controlled chip formation when machining a broad range of steels. The chipforming geometry helps avoid built-up edge and supports stable cutting forces, which in turn aids in achieving a consistent surface finish. The rhombic 55° shape and 0° negative clearance are suited to turning operations requiring a robust edge and flexible approach angles; the 0.8 mm corner radius further contributes to edge strength for medium-duty finishing and semi-finish passes. Clear application spectrum and handling recommendations The grade is specified for steel applications (ISO group P) and is designed to manage the typical heat and chip behaviour of unalloyed and alloyed steels. The insert format and chipbreaker combination provide an economical solution for series production as well as small-batch work where repeatable results are essential. For process setup, follow standard cutting data for the chosen steel subgroup and monitor cutting conditions to exploit the grade’s wear resistance; selecting appropriate speeds and feeds will maximise both performance and cost-efficiency. Contact Metav Werkzeuge for tailored cutting data, availability and specialist advice on the DNMG110408-FW5 WPP10G insert from Walter Tools Technical data Article number: DNMG110408-FW5-WPP10G-WALTER Designation: DNMG110408-FW5 WPP10G Manufacturer: Walter Tools Facts Plate size: 11 Thickness: 04 Corner radius: 0.8 Clearance: 0° (negative) Tolerance class: M Special features Series: Tiger·tec Gold Grade: WPP10G (coated carbide) Chipbreaker: FW5 Shape: Rhombus 55° Material application: Steel (P) FAQ What materials is this insert intended for? The DNMG110408-FW5 WPP10G insert from Walter Tools is specified for machining steels (ISO group P), optimised to handle the heat and chip formation typical of unalloyed and alloyed steels. How does the Tiger·tec Gold coating benefit tool performance? The Tiger·tec Gold coating on the WPP10G grade improves wear resistance under thermal load, helping the insert maintain edge integrity and deliver more consistent tool life in steel turning operations. Which chip behaviour can be expected with the FW5 chipbreaker? The FW5 chipbreaker promotes controlled chip formation for steel machining, reducing the risk of built-up edge and supporting stable cutting forces for better surface quality. Is the negative clearance angle suitable for heavy-duty turning? The 0° negative clearance provides a robust cutting edge suitable for stable, heavier engagement compared with positive-clearance geometries, making the insert appropriate for demanding turning tasks where edge stability is required. What is the significance of the 0.8 mm corner radius? A 0.8 mm corner radius increases edge strength and distributes cutting forces, which helps to resist chipping and is beneficial in semi-finish and finish turning where a balance of strength and surface quality is needed. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen; Germany Protected trademarks and trade names are the property of their respective owners. Brand names and registered trademarks are mentioned for explanatory purposes only. There is no connection between our company and the named brands. The offered article is original, brand-new merchandise of Walter Tools. The Walter AG (brand presentation: Walter Tools) with headquarters in Tübingen is one of the world-leading manufacturers of precision tools for metalworking and is part of the Sandvik Group.
DNMG110408-FW5 WPP20G Wendeplatten - Walter Tools
Take advantage of the combination of Tiger‑tec Gold coating and the FW5 chipbreaker to secure longer tool life and consistent chip control; the robust rhombic geometry with a 0.8 mm corner radius supports stable turning of steels and reduces rework—order directly via Metav Werkzeuge or ask the consultants for cutting data and application support. DNMG110408-FW5 WPP20G – Turning insert, rhombic 55°, Tiger‑tec Gold by Walter Tools A DNMG110408-FW5 WPP20G turning insert designed for steel machining, combining the Tiger‑tec Gold coating with a FW5 chipbreaker to deliver reliable chip formation and productive metal removal Tiger‑tec Gold coated carbide grade WPP20G FW5 chipbreaker for reliable chip control Rhombic 55° shape with 0.8 mm corner radius Optimised for machining steel (ISO group P) Consistent cutting performance for steel turning The coated carbide grade WPP20G, part of the Tiger‑tec Gold series, is formulated for efficient machining of steels (ISO group P). The combination of a wear‑resistant coating and a universal substrate delivers improved tool life and predictable wear behaviour, which translates to reduced tool changes and higher uptime. In practice, this means more consistent component tolerances and fewer interrupted runs in batch production. The chemistry and coating structure are tuned to manage the heat and typical chip formation of steel, making this insert a pragmatic choice where process reliability and repeatability are priorities. Precision geometry that improves component quality The rhombic 55° insert form and 0.8 mm corner radius are designed to balance edge strength with dimensional accuracy. The 0° (negative) relief angle gives the insert a robust edge for interrupted cuts and heavy engagement, reducing the risk of chipping. This geometry helps maintain a stable cutting line and contributes to consistent surface finish, lowering the need for downstream finishing operations. For operations requiring repeatable parts and tight tolerances, the geometry supports predictable tool behaviour under varying cutting forces. Stable chip control and higher process security The FW5 chipbreaker is engineered to shape and evacuate chips reliably when turning steels, minimising the chance of entanglement and cycle interruptions. Effective chip control reduces machine downtime, protects workpiece surfaces and tooling, and simplifies coolant and chip conveyor requirements. Combined with the coated carbide substrate, the chipbreaker promotes uninterrupted machining at production speeds typical for steel turning tasks, delivering measurable productivity gains across mixed production runs. Practical application guidance and compatibility This insert is coded as DNMG110408-FW5 WPP20G and is suitable for a wide range of turning operations on unalloyed and alloyed steels. The insert thickness and size code provide mechanical stability in standard toolholders designed for DNMG geometry. Where heavy roughing or interrupted cuts are frequent, the negative relief and robust chipbreaker create resilience; where finer finishes are required, optimised feeds and speeds with moderate depth of cut will exploit the coating’s wear resistance to maintain surface quality. For precise cutting data, match the insert code with the machine capability and material grade, and consult the detailed cutting charts available from the supplier. Contact Metav Werkzeuge for tailored cutting data, application advice or to request the product DNMG110408-FW5 WPP20G from Walter Tools; eMail info@metav-werkzeuge.com or call +49 2822 7131930 for immediate assistance. Technical Data SKU: DNMG110408-FW5-WPP20G-WALTER Article designation: DNMG110408-FW5 WPP20G Manufacturer: Walter Tools Product type: Turning insert Numbers / Core technical data Insert size: 11 Thickness code: 04 Corner radius: 0.8 mm Relief angle: 0° (negative) Shape: Rhombic 55° Tolerance class: M Chipbreaker: FW5 Design / Special features Grade: WPP20G Series: Tiger‑tec Gold Coating/material: coated carbide Material application: steel (ISO group P) Execution: G ISO designation: DNMG110408-FW5 WPP20G FAQ What materials is this insert suited for? The DNMG110408-FW5 WPP20G insert is optimised for machining steels (ISO group P) and is formulated to handle the heat and chip characteristics typical of unalloyed and alloyed steels. How does the FW5 chipbreaker affect machining? The FW5 chipbreaker on this Walter Tools insert improves chip control and evacuation during turning, reducing the risk of chip entanglement and helping to maintain stable cutting conditions. Is the negative relief angle suitable for interrupted cuts? Yes, the 0° negative relief angle gives the insert a stronger cutting edge that is more tolerant of interrupted cuts and heavy engagement in turning applications. Can this insert be used for finishing operations? With appropriate cutting parameters and feed rates, the WPP20G grade and the insert’s geometry can produce good surface finishes; adjust depth of cut and speed according to the workpiece steel and machine rigidity. What does the Tiger‑tec Gold series provide? The Tiger‑tec Gold series provides a wear‑resistant coating and substrate combination that aims for extended tool life and consistent performance when machining steels with varied cutting conditions. Manufacturer/Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names are mentioned for explanation only; there is no affiliation between our company and the named brands. The offered item is an original, factory‑new product of Walter Tools.
DNMG110408-FW5 WSM20S WSM20S Wendeplatten - Walter Tools
Benefit from the combination of the Tiger·tec Silver coating, the FW5 chipbreaker and the rhombic 55° geometry for reliable chip control and extended edge life; order directly via Metav Werkzeuge or consult the specialists for process optimisation. DNMG110408-FW5 WSM20S turning insert — Tiger·tec Silver, FW5 chipbreaker (Walter Tools) A DNMG110408-FW5 WSM20S indexable turning insert engineered for secure machining of rostfreier Stahl and heat‑resistant superalloys, offering a rhombic 55° geometry and FW5 chip control. Tiger·tec Silver coating WSM20S For rostfreier Stahl and superalloys Rhombic 55° geometry, 0.8 mm corner radius FW5 chipbreaker for secure chip control Predictable cutting performance for demanding materials The insert delivers consistent edge life through a combination of a coated carbide substrate and the WSM20S grade, which is formulated for high thermal and mechanical loads. The FW5 chipbreaker stabilises chip flow, reducing the risk of built‑up edge and facilitating uninterrupted turning cycles; this leads to fewer interruptions and improved machine utilisation. The 0° negative rake supports robust engagement in heavy cuts, while the rhombic 55° form provides low‑interference access to both external and face turning operations. Coating and grade engineered for heat and adhesion resistance The Tiger·tec Silver coating technology enhances heat resistance and wear protection, which is particularly beneficial when machining rostfreier Stahl and materials in ISO group S (heat‑resistant superalloys and titanium). The WSM20S grade is a coated carbide designed to maintain a stable cutting edge under high temperatures and to support controlled chip formation. The insert’s 0.8 mm corner radius balances edge strength with surface finish, making it suitable for components where edge robustness and dimensional consistency are required. Process security and integration into machining cells Produced to tolerance class M, the insert supports repeatable clamping and predictable geometry across production batches. The part designation is optimised for standard toolholders that accept DNMG‑style plates, allowing straightforward integration into existing tool libraries. For applications requiring high process reliability, the combination of chip control, coating technology and geometry reduces scrap rates and improves overall throughput; basic setup parameters and cutting data are selectable according to workpiece material and operation type to achieve reproducible results. Contact Metav Werkzeuge for tailored recommendations on Walter Tools Tiger·tec Silver inserts and assistance with cutting data and availability Technical data Article number: DNMG110408-FW5-WSM20S-WALTER Designation: DNMG110408-FW5 WSM20S Series: Tiger-tec Silver Grade: WSM20S Key figures Geometry: Rhombus 55° Corner radius: 0.8 mm Free angle: 0° (negative) Chipbreaker: FW5 Size code: 11 Thickness code: 04 Tolerance class: M Materials & features Coating: Tiger·tec Silver (coated carbide) Suitable for: rostfreier Stahl (ISO group M) Suitable for: Heat‑resistant superalloys / titanium (ISO group S) Application focus: Heavy and difficult‑to‑machine materials Manufacturer: Walter Tools FAQ What materials is this insert suitable for? The DNMG110408‑FW5 WSM20S insert is designed for rostfreier Stahl (ISO group M) and heat‑resistant superalloys/titanium (ISO group S) due to the thermal stability of the WSM20S grade. How does the FW5 chipbreaker affect machining? The FW5 chipbreaker promotes controlled chip formation and secure evacuation, which reduces the risk of built‑up edge and enhances process stability for continuous turning operations. What is the purpose of the 0° negative rake? The 0° negative rake increases cutting edge robustness for interrupted or heavy cuts, providing improved resistance to mechanical and thermal shock during demanding operations. Can this insert be used in standard DNMG toolholders? Yes, the insert follows DNMG geometry and is compatible with toolholders designed for DNMG‑style indexable plates, enabling straightforward replacement and integration. What advantage does the Tiger·tec Silver coating provide? The Tiger·tec Silver coating increases thermal resistance and wear protection, extending edge life and maintaining consistent surface finish when machining hard or heat‑generating materials. Manufacturer/Responsible: Walter Deutschland GmbH, Derendinger Straße 53, 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and trademarks are mentioned solely for explanatory purposes. There is no affiliation between Metav Werkzeuge and the mentioned manufacturers. The offered article is an original, factory‑new product of the manufacturer.
DNMG110408-MK5 WKK10S WKK10S Wendeplatten - Walter Tools
Combining Tiger·tec Silver coating with a 0.8 mm nose radius and a robust MK5 chipbreaker, this indexable insert provides reliable, long-lasting performance in cast iron turning; order directly via Metav Werkzeuge or contact our consultants for tailored cutting data and selection support. DNMG110408-MK5 WKK10S indexable turning insert, Tiger·tec Silver – for cast iron | Walter Tools A DNMG110408-MK5 WKK10S insert engineered for high-productivity turning of cast iron, featuring a rhombic 55° geometry and a coated-carbide grade tuned to ISO group K materials. Tiger·tec Silver coating for wear resistance Optimised for abrasive cast iron machining Rhombic 55° shape for versatile turning 0.8 mm nose radius for defined profiles Durable coating that extends tool life and reduces downtime The combination of Tiger·tec Silver technology and a coated-carbide substrate delivers measurable advantages when machining cast iron. The coating is engineered to resist abrasive wear and thermal loading commonly encountered with grey and nodular cast irons, which results in longer insert life and more consistent component quality. By choosing a grade tailored to ISO group K, the insert supports stable performance across a broad range of iron alloys while reducing the frequency of tool changes and process interruptions. Geometry and chip control for reliable surface finish and productivity The rhombic 55° geometry, coupled with a 0° (negative) rake and the MK5 chipbreaker, is designed to produce short, controlled chips typical of cast-iron machining. A 0.8 mm nose radius provides a balance between profile definition and tool strength, enabling repeatable surface finishes without compromising tool life. These geometric choices translate directly into process reliability: predictable cutting forces, improved edge stability and consistent dimensional results in repetitive production environments. Application guidance and integration into production Specifically developed for ISO group K applications, the insert performs well with abrasive, brittle workpieces that generate short, breaking chips. The DNMG110408-MK5 WKK10S fits standard toolholders compatible with DNMG inserts and is suitable for both roughing and finishing passes when the machining strategy is adjusted to the grade’s strengths. For new process setups, testing with conservative feeds and optimised speeds is advisable to identify the best compromise between surface finish and tool life; Metav Werkzeuge can provide cutting-data suggestions and batch supply to support production ramp-up. Contact Metav Werkzeuge for specification support and supply of Walter Tools DNMG110408-MK5 WKK10S inserts — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: DNMG110408-MK5-WKK10S-WALTER Designation: DNMG110408-MK5 WKK10S Product type: Indexable turning insert Core data Insert size: 11 Thickness code: 04 Corner radius: 0.8 mm Plate form: Rhombus 55° Rake angle: 0° (negative) Special features Series: Tiger·tec Silver Grade: WKK10S (coated carbide) Chipbreaker: MK5 Material application: Cast iron (ISO group K) FAQ Which materials is this insert suitable for? The DNMG110408-MK5 WKK10S from Walter Tools is optimised for cast iron (ISO group K), designed to handle the abrasive nature and short-chip behaviour of these materials. What does the Tiger·tec Silver series offer? Tiger·tec Silver is a coating technology on a coated carbide substrate that enhances wear resistance and thermal stability for extended performance during cast-iron turning with the DNMG110408-MK5 WKK10S. How does the MK5 chipbreaker affect machining? The MK5 chipbreaker on this insert promotes short, controllable chips and stable cut evacuation, which improves process safety and consistency when turning cast-iron components. What is the benefit of the 55° rhombic geometry and 0.8 mm radius? Rhombic 55° geometry offers versatile approach angles for a range of turning operations, while the 0.8 mm nose radius balances profile accuracy with edge strength for reliable surface quality using the DNMG110408-MK5 WKK10S. Manufacturer / Responsible: Walter Deutschland GmbH; Derendinger Straße 53; 72072 Tübingen Protected trademarks and trade names are the property of their respective owners. Brand names and protected designations are mentioned for explanatory purposes only. There is no affiliation between our company and Walter Tools. The offered article is an original, factory-new product of the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com