Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
12.75mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
High-precision 12.75 mm inspection pin with a ±0.002 mm tolerance and a compact 50 mm length ensures reproducible end‑measurements and simple handling in fine‑mechanical and workshop environments; order directly via Metav Werkzeuge or consult our technical advisors for application advice. Inspection pin, single — 12.75 mm diameter, 50 mm length (Metav IndustryLine) A Inspection pin, single for precise end‑measurement, alignment and go/no‑go verification in fine mechanical, tooling and workshop inspection tasks. 12.75 mm diameter, 50 mm length High precision tolerance ±0.002 mm Special‑steel construction for durability Delivered in a protective transport case Precision where small tolerances determine part acceptance The inspection pin delivers a compact solution when repeatability and minimal measurement uncertainty are required. With a nominal diameter of 12.75 mm and a verified ±0.002 mm manufacturing tolerance, this pin suits sensitive end‑measurements and alignment tasks where millimetre‑level play is unacceptable. Classified in the Micro range of calipers and gauge pins, it is designed for fine‑mechanical work such as small shaft checks, dowel verification and end‑face gauging. The tight tolerance reduces rework and inspection time by providing a reliable reference for pass/fail decisions on small components. Robust workshop execution for everyday use Built as a workshop version, the gauge combines the handling convenience required on the shop floor with the dimensional stability needed in quality control. The 50 mm length provides a practical reach without compromising stiffness, while the special steel construction offers wear resistance under repeated engagement. Supplied in a protective transport case, the pin remains protected during storage and transit, preserving surface condition and dimensional integrity. Its modest mass facilitates quick manual handling and straightforward insertion into fixtures or measuring rigs. Seamless fit into inspection workflows and fixtures Integration into existing inspection routines is straightforward: the pin functions as a fixed reference for end stops, plug checks and alignment aids in assembly and fixture set‑ups. Traceable manufacturing tolerances enhance the efficiency of measurement loops and reduce uncertainty propagation in serial checks. The compact design supports rapid component throughput and minimal fixturing modifications, making the pin useful both for occasional verification and for repeatable quality control runs. Backed by the Metav IndustryLine quality standard, it contributes to a dependable measurement chain in small‑part production environments. For workshop measurement that demands reliable small‑part control, choose the Metav IndustryLine inspection pin and contact Metav Werkzeuge in Emmerich for tailored application advice and swift supply Technical Data Article number: M323.C75 GTIN: 4061905066498 Product type: Inspection pin (single) Material: Special steel Version: Workshop execution Packaging: Protective transport case Numeric data Diameter: 12.75 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Weight: 0.1 kg Materials & features Corrosion‑resistant surface profile (special steel) Suitable for end‑measurement and alignment tasks Compact form factor for micro‑precision applications Delivered single, ready for installation FAQ What tolerance can be expected from this inspection pin? The inspection pin is supplied with a manufacturing tolerance of ±0.002 mm, making it suitable for fine end‑measurements and precise alignment tasks in workshop environments. Is the pin suitable for repeated shop‑floor use? Yes, the Metav IndustryLine workshop version is designed for durable handling; the special‑steel construction and protective transport case preserve dimensional stability during repeated use. How does the pin integrate with existing fixtures and gauges? The pin's compact 50 mm length and precise diameter allow straightforward integration as an end stop or reference pin in fixtures, jigs and assembly checks without extensive modification. Can this pin be used for small shaft or dowel verification? Indeed — the 12.75 mm diameter and tight tolerance make the pin appropriate for shaft checks, dowel verification and similar micro‑part acceptance tests. Is calibration or a certificate included with the delivery? Standard delivery does not imply ISO 17025 calibration; the inspection pin is supplied in a protective case and ready for immediate use. Specific calibration services can be discussed with Metav Werkzeuge if traceable certification is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.76mm Gauge Pin Single 50mm Length Workshop Finish - Metav IndustryLine
High-precision gauge pin in a workshop design delivers repeatable end-measure checks with a tight ±0.002 mm tolerance and robust special steel construction; order the gauge pin directly via Metav Werkzeuge or ask our consultants for tailored advice. Gauge pin, single, 12.76 mm (50 mm length) — Workshop-grade gauge pin with ±0.002 mm tolerance, Metav IndustryLine The gauge pin, single, 12.76 mm is a workshop-grade cylindrical inspection pin intended for end-measure checks and verification tasks in machine shops and quality-control benches, with a 50 mm working length. Diameter 12.76 mm, nominal fit Tolerance ±0.002 mm precision Length 50 mm for end-measure checks Workshop-grade special steel construction Repeatable end-measure precision for inspection tasks Engineered for consistent dimensional checks, this cylindrical inspection pin provides a nominal diameter of 12.76 mm with a verified ±0.002 mm deviation. Such a tight tolerance reduces measurement scatter and shortens inspection cycles, so production-control processes run more predictably. The combination of precise diameter and controlled length makes the component particularly suited to quick go/no-go assessments, incoming material verification and final inspection steps where repeatable measurements are critical to maintaining quality standards. Durable workshop construction that endures handling Constructed from special steel and specified as a workshop version, the pin balances wear resistance with dimensional stability under routine use. The 50 mm working length gives adequate engagement for end-face and through-hole checks while remaining easy to handle at the bench. The robust material choice and workshop specification ensure the part withstands daily use without frequent rework, supporting longer service intervals and fewer production interruptions — an efficiency gain for busy metalworking and maintenance environments. Practical handling and integration into inspection routines With a plain cylindrical design and nominal diameter, the gauge pin integrates smoothly into existing inspection jigs and measuring setups. The straightforward geometry allows fast seating in fixtures and simple visual confirmation of fit, reducing operator decision time. Where repeated checks are required, the component’s stable dimensions support statistical process control and help to maintain traceable records of part conformity. For users seeking reliable reference elements for small-batch quality control or toolroom verification, this item offers a compact, low-complexity solution with high measurement confidence. For reliable end-measure checks with Metav IndustryLine components please contact Metav Werkzeuge GmbH in Emmerich for product details and procurement; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.C76 GTIN: 4061905066504 Manufacturer: Metav IndustryLine SKU: M323.C76 Facts Diameter: 12.76 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: special steel Label: Gauge pin, single, 12.76 mm length 50 mm Accuracy class: ±0.002 FAQ What is the nominal diameter and tolerance of the pin? The pin has a nominal diameter of 12.76 mm with a stated tolerance of ±0.002 mm for precise end-measure checks. Is this gauge pin suitable for daily workshop inspection? Yes; the workshop-grade specification and special steel construction make this pin suitable for routine inspection and verification tasks in a machine shop. What is the usable length of the inspection pin? The usable working length is 50 mm, providing stable engagement for end-face and through-hole checks. Can this component be used as a reference in processing jigs? The plain cylindrical geometry and stable diameter allow integration as a reference element in inspection jigs and simple fixtures. Which brand manufactures this gauge pin and what is the article number? This is a Metav IndustryLine gauge pin, article number M323.C76 (GTIN 4061905066504). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.77mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
The combination of consistent diameter control, tight tolerance and robust workshop design ensures repeatable measurement and secure fixture reference in production environments. Benefit from a durable, single-piece test pin that supports reliable end-length checks and straightforward stock integration; order directly via Metav Werkzeuge or consult the technical team for specification matching. Test pin, single – 12.77 mm Ø × 50 mm, workshop version (Metav IndustryLine) A test pin 12.77 mm Ø, length 50 mm designed as a precise reference for end-length inspection, fixture alignment and repeatable gauge tasks in workshop and inspection applications. Precision diameter 12.77 mm, tolerance ±0.002 mm Solid special-steel construction for durability Designed for end-length inspection and fixture use Single-piece supply, ready for immediate integration Consistent metrology for repeatable results The solid reference pin delivers high repeatability thanks to its controlled diameter of 12.77 mm and a verified displacement tolerance of ±0.002 mm. This level of precision supports quality assurance and fixture checks where reproducible contact points reduce cumulative error. Using a defined, hardened contact geometry minimises deformation under load, which translates directly into fewer rejections and steadier process control. Robust construction for workshop environments Manufactured from special steel, the component resists wear and preserves the reference surface over prolonged use. The 50 mm length provides adequate engagement for many gauge and fixture arrangements while remaining compact for easy handling and storage. The workshop specification signals a design focus on durability and practical operability rather than delicate lab-only handling, making the part suitable for everyday production use. Practical integration into inspection workflows Supplied as a single unit with a clear article identity, the pin simplifies inventory and toolroom logistics when used as an end gauge or datum element. Its straightforward geometry enables fast substitution in fixtures and jigs, supporting lean maintenance routines and shortening downtime during inspections. The combination of material choice and tight tolerance makes it a reliable reference for comparative or go/no-go checks in small-batch and series production. For precision fixture references and dependable end-length checks, contact Metav Werkzeuge to specify the Metav IndustryLine test pin M323.C77 or request tailored application advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.C77 GTIN: 4061905066511 Manufacturer: Metav IndustryLine Label: Test pin, single, 12.77 mm Ø length 50 mm eClass: 21170231 Specifications Diameter: 12.77 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Features Material: Special steel Version: Workshop execution Supply: Single-piece test pin Application hint: End-length inspection and fixture reference FAQ What is the core accuracy of this test pin? The test pin M323.C77 from Metav IndustryLine is manufactured to a tolerance of ±0.002 mm, providing a stable reference for end-length measurements and fixture checks. Which materials is the pin intended to work with? The Metav IndustryLine test pin is a hardened special-steel reference component suitable as a contact datum across common workshop materials where a durable reference point is required. How is the test pin supplied and identified? The item is supplied as a single test pin labelled as M323.C77 (GTIN 4061905066511) for straightforward stock control and immediate use in gauges and fixtures. Can this pin be used as a datum in jigs and fixtures? Yes, the 12.77 mm diameter and robust construction make the Metav IndustryLine test pin suitable as a datum or reference element in jigs and fixtures for repeatable checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.78mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of high repeatability and compact handling for reliable end‑dimension checks: the combination of ±0.002 mm tolerance, a 12.78 mm nominal diameter and workshop-ready construction ensures consistent measuring results in routine inspection work. Order the pin directly via Metav Werkzeuge or consult the specialists for application advice. Test pin M323.C78 — Gauge pin, Ø 12.78 mm, length 50 mm (Metav IndustryLine) The Test pin M323.C78 is a precision end‑measurement pin designed for workshop inspection, setting gauges and repeatable reference checks in fine mechanical environments. Workshop‑grade construction Diameter 12.78 mm precision Tolerance ±0.002 mm Supplied in protective transport case Consistent end‑measurement with fine tolerance A compact reference element for end‑dimension checks, this gauge pin provides ±0.002 mm tolerance, which corresponds to sub‑micron repeatability suitable for demanding workshop quality control. As a single, solid pin it serves as a fixed reference when setting fixtures or checking mating bores, reducing cumulative error in assembly tasks. The clear numerical specification of 12.78 mm diameter and 50 mm length enables straightforward selection and interchange with existing pin sets or gauge blocks. Durable, workshop‑ready material and handling Constructed from special steel, the pin withstands daily shop handling while maintaining dimensional stability. The 50 mm shank length balances reach and stiffness for handheld positioning or fitted checks in jigs. Supplied in a protective transport case, the item is designed for safe transit and organised storage on the shop floor, preserving the reference surface between uses. The workshop‑oriented design prioritises robustness without compromising the precision required for repeatable results. Easy integration into inspection routines As a compact precision element within the micro range, the pin suits fine mechanical and general machine‑shop contexts where repeatability and ease of use matter. The single‑piece format simplifies inventory management and replacement; clear labelling supports traceability in inspection processes. When paired with calibrated micrometres or bore gauges, the pin functions as a stable reference for setting tools and verifying end dimensions, helping to maintain throughput while meeting inspection tolerances. For workshop enquiries and to discuss the suitability of the Metav IndustryLine test pin for specific inspection tasks, contact Metav Werkzeuge in Emmerich by phone or e‑mail for tailored advice and order processing: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M323.C78 GTIN: 4061905066528 Label: Test pin, single, 12.78 mm, length 50 mm Facts Diameter: 12.78 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: special steel Supplied as single pin Delivered in protective case for transport Suitable for end‑measurement checks FAQ What accuracy can be expected from this test pin? The test pin M323.C78 is specified with a tolerance of ±0.002 mm, providing high repeatability for workshop inspection tasks. Is the pin suitable for routine jig and gauge setting? Yes, the gauge pin is designed as a workshop‑grade reference for setting fixtures and checking bores, offering a stable datum at 12.78 mm diameter. How is the item supplied and protected during transport? The pin is supplied as a single unit and comes in a protective transport case to preserve the measuring surfaces during handling and transit. Can this pin be used alongside calibrated micrometres or bore gauges? The M323.C78 is intended for integration into inspection routines and pairs well with calibrated micrometres and bore gauges as a stable reference element. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.79mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of precise locating and repeatable end‑size verification thanks to the 12.79 mm diameter and robust 50 mm length, paired with an exacting ±0.002 mm tolerance for consistent inspection results. Order the gauge pin directly via Metav Werkzeuge or ask the consultants for application advice. Gauge pin, single — 12.79 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin M323.C79 for end‑size inspection, fixture locating and workshop verification tasks Precision tolerance ±0.002 mm Diameter 12.79 mm, machined to fit 50 mm hardened length for stable seating Workshop‑grade special steel construction High‑precision geometry that stabilises inspection results The M323.C79 is engineered for reproducible locating and end‑size checks. With a diameter of 12.79 mm and a declared positional tolerance of ±0.002 mm, the pin offers the dimensional certainty required for go/no‑go fixtures, gauge plates and end‑of‑line checks. The close tolerance reduces uncertainty in measurement chains and limits rework by ensuring that locating surfaces and mating bores present consistent fits. Stated values are suitable for precision workshop use where stable repeatability is a decisive factor. Robust material and format for everyday workshop use Manufactured from special steel and supplied in a workshop version, the pin combines wear resistance with dimensional stability under regular handling. The 50 mm length provides sufficient engagement in locating bores while maintaining rigidity to prevent bending or tilt during insertion. The single‑piece design and machined finish simplify integration into jigs, test fixtures and bench gauges, delivering a practical balance between service life and handling convenience in typical production and inspection environments. Practical integration into inspection workflows Identification data such as GTIN 4061905067273 and the article code M323.C79 allow straightforward inventory management and traceability within procurement and quality systems. The pin suits use as a reference or interchange part in modular fixture concepts and can be paired with hardened bushings or alignment sleeves where precise seating and repeatable datum definition are required. The compact form factor supports easy storage and quick substitution during batch changes, supporting a smooth inspection routine without complex adaptation. Contact Metav Werkzeuge today for technical advice on the Metav IndustryLine M323.C79 gauge pin and to arrange prompt supply from Emmerich. Technical Data Article number: M323.C79 GTIN: 4061905067273 Manufacturer: Metav IndustryLine ECLASS: 21170231 Numbers Diameter: 12.79 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop version Single gauge pin Label: Prüfstift, einzeln, 12,79 mm Länge 50 mm FAQ What tolerance can be expected from this gauge pin? The gauge pin is specified with a tolerance of ±0.002 mm, ensuring high repeatability for workshop inspection and fixture locating tasks with the M323.C79 from Metav IndustryLine. Is the pin suitable for use in assembly fixtures and jigs? Yes, the 50 mm length and robust special steel construction make the pin suitable for fixtures, jigs and modular locating systems where stable seating and repeatable positioning are required. How is the product identified for ordering and inventory? The item is listed under article code M323.C79 and GTIN 4061905067273, which simplifies procurement and traceability in quality systems. Can the pin be used as a reference for end‑size verification? The manufactured tolerance of ±0.002 mm makes the pin appropriate for end‑size checks and comparison measurements in workshop and inspection environments. What material is used and how does it affect durability? Constructed from special steel, the pin delivers improved wear resistance and dimensional stability during routine handling and repeated seating operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.7mm Gauge Pin, Workshop Version, 50mm Length - Metav IndustryLine
Take advantage of a compact, workshop‑grade pin that combines high repeatability and robust handling for fast in‑process checks; the precise diameter and tight tolerance keep inspection times low and scrap rates down. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for specification support. Gauge pin, single, 12.7 mm dia, 50 mm length (Metav IndustryLine) The Gauge pin, single, 12.7 mm dia, 50 mm length is a workshop‑grade precision pin intended for end‑measure verification and tight‑tolerance gauging in fine mechanical and small‑parts inspection. Precise tolerance ±0.002 mm 12.7 mm nominal diameter 50 mm compact overall length Workshop version with transport case Consistent, repeatable checks for production control A compact gauge pin with a ±0.002 mm tolerance supports reproducible verification across batches. The tight tolerance reduces ambiguity during go/no‑go checks and speeds up decision making on the shop floor, which improves throughput and reduces rework. Made from special steel, the pin delivers stable dimensional behaviour under normal workshop conditions; corrosion resistance and surface finish are therefore key for preserving the measured nominal 12.7 mm over many cycles. The compact format shortens handling times, allowing operators to perform frequent checks without interrupting the production flow. Compact format tailored to micro and fine‑mechanical work With a nominal diameter of 12.7 mm and a 50 mm overall length, this item falls into the micro class for small‑part measurement, offering the balance of reach and stiffness needed for precision components. The short length minimises deflection and torsion during insertion, which matters when measuring small bores, pins or mating features in assemblies. This geometry is especially useful in watchmaking, instrumentation and micro‑assembly environments where reliable, tactile feedback and minimal operator influence on the result are essential. Built for workshop use and straightforward handling The workshop version construction focuses on everyday usability: it is robust enough for routine checks yet compact to remain convenient in a busy measurement desk. Delivery in a transport case protects the pin during storage and transit and helps preserve calibration state and surface condition. At approximately 0.1 kg, the pin is easy to manipulate while maintaining the mass required for stable seating in gauges and fixtures. The overall design prioritises fast inspection cycles and low maintenance, making it a practical tool for quality engineers and production technicians. For reliable, repeatable pin gauging choose the Metav IndustryLine gauge pin—order from Metav Werkzeuge for immediate supply or contact our Emmerich team for technical advice Technical data Article number: M323.C70 GTIN: 4061905066160 SKU: M323.C70 Brand: Metav IndustryLine Material: Special steel Version: Workshop version Facts Nominal diameter: 12.7 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.1 kg Special features Delivery: Transport case for safe handling Intended use: End‑measure verification and pin gauging Compact format suitable for micro / fine‑mechanical inspection Robust workshop execution for frequent use FAQ What is the nominal diameter and length of this gauge pin? The gauge pin has a nominal diameter of 12.7 mm and an overall length of 50 mm, specified as a compact inspection pin for small‑parts measurement. How precise is the pin for pass/fail checks? The pin is manufactured to a tolerance of ±0.002 mm, providing tight dimensional control for reliable go/no‑go and reference measurements. Which materials is this pin suitable to check? This precision pin is suitable for dimensional checks of small metallic and engineered parts where a hardened or finished bore is inspected; the pin itself is made from special steel for stable performance. Is the pin supplied ready for workshop use? Yes. The item is a workshop version and is delivered in a transport case to protect the surface and ensure safe handling between uses. Can this pin be used for metrological calibration labs? The pin is designed for production and workshop inspection tasks; for laboratory calibration use, please consult Metav Werkzeuge to confirm suitability and calibration requirements for specific procedures. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.81mm Gauge Pin Length 50mm Workshop Version, Special Steel - Metav IndustryLine
Take advantage of precise diameter control and low tolerance for repeatable inspection results; the combination of 12.81 mm nominal diameter, a ±0.002 mm tolerance and a robust 50 mm length ensures reliable go/no-go and reference checks in workshop environments. Order directly via Metav Werkzeuge or consult our specialists for application advice. Test pin, single, 12.81 mm diameter — 50 mm length (M323.C81) A single gauge pin 12.81 mm designed for precise end measurements and routine inspection tasks in workshops and quality control stations. 12.81 mm precision diameter Tolerance ±0.002 mm 50 mm hardened length Workshop version with transport case Accuracy that stabilises inspection routines A compact gauge pin with a nominal diameter of 12.81 mm and a measured tolerance of ±0.002 mm offers immediate, verifiable results when used for final diameter checks and reference measurements. The tight tolerance reduces decision uncertainty during go/no-go testing and supports faster throughput in incoming inspection and small-series production. Measurable performance translates into fewer rework loops and clearer pass/fail criteria for operators and inspectors alike. Robust design for everyday workshop use Manufactured from special steel and supplied in a workshop version, the pin combines dimensional stability with handling durability. The 50 mm length provides sufficient contact area for axial seating and repeatable orientation while remaining compact for bench-top use. Delivery includes a transport case to protect the instrument from knocks and contamination during storage and transit, preserving the geometric integrity that underpins repeatable measurements. Practical applications and integration into inspection workflows The pin is suitable for a range of inspection scenarios, from tactile checks to use as a reference in fixtures and gauges. Its compact form factor makes it convenient for spot checks on machined components and for assembly verification where clear end-measure data are required. The model M323.C81 from Metav IndustryLine fits directly into established measurement routines, offering improved repeatability and a pragmatic balance between reach and stiffness for everyday quality control tasks. For workshop-ready precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for tailored advice and efficient delivery to your workbench. Technical data Article number: M323.C81 GTIN: 4061905067297 Label: Prüfstift, einzeln, 12,81 mm Länge 50 mm Category: Messstifte Facts Nominal diameter: 12.81 mm Tolerance: ±0.002 mm Length: 50 mm Weight: 0.1 kg Materials & special features Material: Special steel Delivery: Single pin in transport case Version: Workshop execution Intended use: End measurements, go/no-go and reference checks FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.C81 is specified with a tolerance of ±0.002 mm, enabling consistent pass/fail assessment in inspection routines. Is the test pin suitable for workshop use and transport? Yes. The workshop execution and included transport case protect the pin during handling and storage while keeping it ready for routine checks. Can this pin be used as a reference in fixtures? The M323.C81 test pin is suitable for use as a reference feature in fixtures and simple gauges where a precise nominal diameter and short length are required. What material is the pin made from and why does it matter? The pin is made from special steel, chosen for dimensional stability and resistance to wear in regular inspection tasks, maintaining measurement integrity. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.82mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the high repeatability and tight tolerance of ±0.002 mm combined with the resilient special steel construction for consistent end‑measure checks; order directly via Metav Werkzeuge or consult our specialists for tailored procurement. M323.C82 gauge pin — 12.82 mm diameter, 50 mm length (Metav IndustryLine) M323.C82 is a precision gauge pin designed for end‑measure checks and plug‑fit verification in workshop and inspection settings. Workshop version for robust daily use Diameter 12.82 mm for tight tolerances Tolerance ±0.002 mm for reliable inspection Precision that reduces measurement uncertainty The M323.C82 is manufactured to a tolerance of ±0.002 mm, which positions it for tasks where repeatable, measurable fits are essential. This level of control reduces the risk of downstream rework by providing a clear go/no‑go reference for bores and fits. Using a hardened gauge pin with such a narrow tolerance gives labs and workshops a deterministic reference point during incoming inspection or final quality checks, improving throughput and lowering the incidence of non‑conforming parts. Built to withstand workshop handling while remaining easy to use Constructed from special steel, the pin resists wear and maintains dimensional stability under regular use. At 50 mm length and a compact design, the component is straightforward to handle and store, while the mass distribution keeps it steady during manual checks. The workshop version specification indicates a balance between robustness and precision, suitable for frequent measurement routines on the shop floor without compromising the nominal dimensions required for precise assembly operations. Fits into quality workflows and traceable inventory systems The plain cylindrical form makes the pin compatible with standard gauge sets and bench procedures; it serves as a quick reference for bore acceptance and plug tests. Identified by SKU M323.C82 and GTIN, the item integrates cleanly into production tracking and stock systems. Clear identification and repeatable geometry support documented inspection procedures, enabling reliable records for audits and supplier quality checks and helping teams meet production tolerances consistently. Discuss batch availability and supply options for the M323.C82 with Metav Werkzeuge to align delivery with production cycles and quality plans. Technical data Article number: M323.C82 GTIN: 4061905067303 Manufacturer: Metav IndustryLine Material: Special steel Label: Prüfstift, einzeln, 12,82 mm Länge 50 mm ECLASS: 21170231 Facts Diameter: 12.82 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Weight: 0.1 kg Measurement range (max): 12.82 mm Special features Workshop execution for everyday use Single test pin, plain cylindrical geometry Suitable for end‑measure and plug‑fit verification SKU: M323.C82 FAQ What applications is this gauge pin intended for? The M323.C82 gauge pin is designed for end‑measure checks, plug‑fit verification and quick bore acceptance tests in workshop and inspection environments. How tight is the dimensional accuracy of the pin? The M323.C82 is manufactured to an accuracy of ±0.002 mm, providing a high‑precision reference for fit and tolerance checks. Which material is used and what does that mean for durability? Made from special steel, the pin balances wear resistance with dimensional stability so it performs reliably under frequent handling in workshop conditions. How is the item identified for inventory and traceability? This test pin is listed under SKU M323.C82 and GTIN 4061905067303, allowing easy integration into stock and quality‑management systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.83mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Benefit from workshop‑grade durability and consistently repeatable results: the test pin combines special steel construction, a precise 12.83 mm diameter and a measured accuracy of ±0.002 mm to secure reliable end‑measurement and fixture alignment. Order the component directly via Metav Werkzeuge or consult our specialists for integration advice. Test pin M323.C83 – 12.83 mm diameter, 50 mm length (Metav IndustryLine) A Test pin M323.C83 for end‑dimension checks and gauge fixture use in workshop and inspection environments Workshop version for robust everyday use Diameter 12.83 mm for precise fit 50 mm overall length for gauge fixtures Accuracy ±0.002 mm for tight tolerances Precision designed for repeatable measurements The M323.C83 is engineered to deliver consistent measurement results where tolerances matter. With a nominal diameter of 12.83 mm and an indicated accuracy of ±0.002 mm, the pin supports tight repeatability during end‑measurements and reference setups. This level of precision reduces ambiguous readings and the need for corrective rework; the specified tolerance describes the maximum deviation expected under normal inspection conditions and therefore gives a clear quality benchmark for process control. Built for daily workshop use Constructed from special steel and released as a workshop version, the pin balances hardness and handling for everyday use in inspection benches and jigs. The 50 mm overall length provides a convenient projection for mounting and reference while remaining compact enough for tight fixture spaces. Robust material selection and a practical design minimise deformation risk during repeated handling, extending service life and maintaining dimensional integrity across production batches. Practical integration for gauges and fixtures Designed as a single inspection element for end‑measurements and gauge fixtures, this pin simplifies assembly into existing test rigs and reference layouts. The compact form factor reduces cycle‑time during manual gauging operations and aids quick alignment in small‑batch and series production. Where parts must be checked repeatedly, the component’s stable geometry and workshop orientation support reliable positioning and reproducible measurement outcomes, contributing to higher throughput and fewer quality interruptions. For workshop‑grade precision and reliable fixture integration, request the M323.C83 test pin from Metav Werkzeuge — our consultants at Metav Werkzeuge can advise on matching the component to existing gauges and production setups. Technical data Article number: M323.C83 GTIN: 4061905067310 SKU: M323.C83 Manufacturer: Metav IndustryLine Material: Special steel Facts Diameter: 12.83 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Workshop version Application: end measurements Label: Test pin, single piece Category: Measuring pins FAQ What are the primary dimensions of the test pin? The test pin has a diameter of 12.83 mm and an overall length of 50 mm, with an indicated accuracy of ±0.002 mm. Which material is used for the pin? The component is made from special steel, specified for robust workshop use. Is this pin suitable for gauge fixtures and end‑measurements? Yes, the workshop version is intended for use in gauge fixtures and end‑dimension checks where stable contact and repeatable references are required. What identifier should be used when ordering? Order using article number/SKU M323.C83; the GTIN is 4061905067310 for logistics and stock handling. How does the stated accuracy affect measurement processes? An accuracy of ±0.002 mm defines the expected maximum deviation during normal inspection use, supporting reliable comparative checks and consistent quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.84mm Test Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of precision and durable construction for consistent end-size checks; the 50 mm length and 12.84 mm diameter combine to deliver reliable repeatability in workshop environments. Order the gauge pin directly via Metav Werkzeuge or consult the technical team for specification support. Gauge pin, single, Ø 12.84 mm, length 50 mm (M323.C84) — Metav IndustryLine workshop version The gauge pin M323.C84 is a single inspection pin designed for repeatable end‑size and go/no‑go checks in workshop and inspection settings, providing a compact, high‑precision reference for assembly and quality control. Precision tolerance ±0.002 mm Ø 12.84 mm workshop grade Special steel construction Supplied in transport case Measured precision that reduces rework and uncertainty The gauge pin is engineered to a fine tolerance of ±0.002 mm, delivering a measurable advantage where conformity to tight limits is mandatory. For routine inspection tasks, this level of control reduces the need for repeated checks and lowers scrap rates; the narrow tolerance is particularly beneficial when used as a reference in jigs, fixture verification or end‑of‑line checks. The influence of material wear is minimised by the choice of special steel, which preserves dimensional integrity over repeated cycles. Built for workshop demands and repeat use This workshop version combines a compact 50 mm shaft with a stable 12.84 mm diameter to ensure handling comfort and resistance to deformation during frequent use. The construction suits manual inspection benches and can be integrated into simple gauge assemblies; the solid metal core supports consistent contact geometry, which in turn keeps measurement scatter low. The product’s robustness decreases downtime and maintenance intervals, offering operational efficiency for everyday production tasks. Practical handling, storage and traceability Supplied individually and packed in a transport case, the pin is protected against knocks and contamination during storage and transit. The single‑item delivery supports traceable handling when individual components are needed for specific inspection routines. A compact form factor ensures easy placement in inspection trays or pockets on the shop floor, while the clear marking and SKU M323.C84 facilitate inventory control and reorder processes. Why this choice supports dependable workflows Choosing a precisely manufactured gauge pin from a trusted line reduces uncertainty across multiple stages of production: set‑up, in‑process checks and final acceptance. The combination of special steel material and workshop design keeps the reference geometry stable under normal working conditions, helping teams reach consistent quality outcomes. Where repeated go/no‑go verifications are part of the routine, a dedicated, well‑specified pin like this one streamlines inspection procedures and strengthens quality documentation. For consistent end‑size verification and workshop durability, contact Metav Werkzeuge to request the M323.C84 gauge pin and secure dependable supply and expert advice from Emmerich. Technical data SKU: M323.C84 GTIN: 4061905067327 Brand: Metav IndustryLine Facts Diameter: 12.84 mm Length: 50 mm Mass: 0.1 kg Tolerance / accuracy: ±0.002 mm Special features Material: Special steel Workshop version Supplied in transport case FAQ What is the primary application of this gauge pin? The gauge pin M323.C84 is intended for end‑size checks, go/no‑go trials and fixture verification in workshop and light‑industrial inspection workflows. Is the material corrosion resistant? The pin is made from special steel designed for wear resistance; for specific corrosion resistance requirements, surface treatment options should be discussed with Metav Werkzeuge. Can this gauge pin be used in measurement fixtures? Yes, the robust geometry and defined tolerance of ±0.002 mm make the pin suitable as a fixed reference in simple fixtures and assembly checks. How is the item delivered and protected during transport? The pin is supplied individually and packed in a transport case to protect the reference surface and maintain traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.85mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of industrial accuracy, robust special steel construction and a compact 50 mm length for straightforward end‑measurement tasks; the pin gives repeatable reference points and low handling fatigue. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.C85 — single, Ø 12.85 mm, 50 mm length The Gauge pin M323.C85 is a compact test pin for precise end‑measurements and reference checks in workshop metrology. Compact Ø 12.85 mm diameter for tight fits High repeatability with ±0.002 mm tolerance 50 mm length for accessible end‑face checks Workshop design with durable special steel finish Precision where it matters: consistent, measurable accuracy The pin delivers ±0.002 mm repeatability, a level of control that supports high‑confidence inspection in production and assembly processes. Machined from special steel, the geometry of the cylindrical shaft and the flat end are optimised to provide a stable datum with minimal run‑out. This makes the component suitable as a fixed reference for end‑measurements, plug checks and alignment tasks where a defined, reproducible contact is required. The technical tolerance and material choice reduce variability during repeated cycles, which directly improves process reliability and lowers scrap risk. Practical workshop benefit: easy handling and reliable results With a 50 mm length and a compact Ø 12.85 mm profile, the component fits confined bores and narrow access points without sacrificing stiffness. The modest mass (approx. 0.1 kg) and straightforward geometry allow single‑handed placement and quick verification sequences at the bench or on a fixture. As a single gauge pin it is well suited to end‑face gauging, reference probing and temporary datum set‑up. The workshop specification ensures robustness under routine handling, while the surface finish of the special steel supports repeatable contact conditions and long service life. Proven supply chain and partner assurance Sourcing through Metav places the product within a quality‑filtered delivery system backed by decades of metrology experience. The component is offered with clear identification (SKU M323.C85, GTIN available) and concise technical data for procurement and traceability. Choosing this workshop‑grade pin means benefiting from Metav’s broad parts range and dependable logistics, which simplifies inventory management and supports uninterrupted production planning. Contact Metav Werkzeuge for ordering and technical clarification on the M323.C85 gauge pin—sales and product specialists in Emmerich are available by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.C85 GTIN: 4061905065156 Material: Special steel Category: Gauge pins Core data Diameter: Ø 12.85 mm Length: 50 mm Weight: 0.1 kg Tolerance / repeatability: ±0.002 mm Special features Workshop design (robust handling) Single gauge pin configuration Suitable for end‑measurements and reference checks SKU: M323.C85 FAQ What materials is the pin made from? The pin is manufactured from special steel, which provides wear resistance and stable contact properties for repeated measurements with the M323.C85 gauge pin. What level of accuracy can be expected? The gauge pin offers a repeatability of ±0.002 mm, making it suitable for precise end‑measurements and reference operations in workshop environments. Can this pin be used in tight bores and narrow fixtures? Yes — the Ø 12.85 mm diameter and 50 mm length are designed for confined access and make the M323.C85 appropriate for plug checks and alignment in restricted spaces. Is the pin delivered with traceable identification? The M323.C85 is supplied with its SKU and GTIN for procurement and traceability purposes; further documentation can be requested via Metav Werkzeuge. How should the gauge pin be maintained to ensure longevity? Regular cleaning to remove debris and light protection from corrosive environments will maintain the contact quality of the pin; handling and storage within the workshop best practices are recommended for long service life. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.86mm Test Pin, Single, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of precise end-measure checks with a compact, workshop-grade gage pin that combines tight tolerance and robust construction. With a 12.86 mm diameter held to ±0.002 mm and a 50 mm overall length, this single pin supports dependable fixture set-up and go/no‑go verification; order directly via Metav Werkzeuge or consult our specialists for application advice. Gage pin M323.C86 — 12.86 mm Ø, 50 mm length (Metav IndustryLine) The M323.C86 gage pin is a single precision pin designed for end‑measure verification and fixture alignment in workshop and inspection environments Diameter 12.86 mm precision pin Tolerance ±0.002 mm for accurate checks 50 mm overall length for end‑measure points Special steel, workshop grade Precise checks where repeatability matters The compact design delivers high repeatability for end‑measure and alignment tasks. Its nominal diameter of 12.86 mm is produced to a tight ±0.002 mm deviation, ensuring that fit checks and datum references remain consistent across repeated measurements. This level of mechanical accuracy supports quick comparative assessments on production lines and in maintenance work, reducing rework and helping to maintain process stability. Durable construction for frequent use Manufactured in special steel, the pin offers dimensional stability and wear resistance appropriate to a workshop environment. The 50 mm length provides sufficient engagement for many plug and fixture applications while remaining easy to handle. The workshop‑grade execution balances durability and machinability, meaning the component resists edge damage during regular insertion and removal yet stays serviceable for long inspection cycles. Practical applications and compatibility Ideal for end‑measure verification, fixture set‑up and bore alignment, the pin functions as a reliable reference in assembly jigs and go/no‑go procedures. Its compact mass and 0.1 kg weight make handling straightforward during repeated use, and the single‑piece delivery supports targeted replacement of worn reference elements. Where precise plug gauges or alignment pins are required, this component integrates well into existing inspection tool sets. Contact Metav Werkzeuge today for supply and technical advice on Metav IndustryLine gage pins from Emmerich, and ensure the right specification for measurement and fixture tasks Technical data SKU: M323.C86 GTIN: 4061905065163 Material: Special steel Length: 50 mm Diameter: 12.86 mm Tolerance: ±0.002 mm Weight: 0.1 kg Version: Workshop grade Facts Length: 50 mm Diameter: 12.86 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Single pin delivery Workshop‑grade execution Special steel construction ECLASS: 21170231 FAQ What is the nominal diameter and its tolerance? The nominal diameter is 12.86 mm; the manufacturing tolerance is ±0.002 mm for precise fit and verification. Is this pin suitable for workshop use and frequent handling? Yes — the workshop‑grade construction and special steel make the pin robust enough for repeated insertion and fixture work. Can the pin be used for fixture alignment and end‑measure checks? The pin is intended for end‑measure verification, fixture set‑up and go/no‑go checks; it integrates well with assembly jigs and reference tooling. How long is the gage pin and what is its mass? The overall length is 50 mm and the weight is approximately 0.1 kg, offering easy handling during repeated operations. Which product reference should be quoted when ordering or enquiring? Please refer to gage pin M323.C86 (Metav IndustryLine) or SKU M323.C86 when requesting supply or technical information. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.87mm Gauge Pin 50mm Length, Workshop Version, Special Steel - Metav IndustryLine
Take advantage of ±0.002 mm accuracy and a special steel construction to ensure repeatable end‑dimension checks; the slim 12.87 mm gauge pin with 50 mm length offers a reliable fit for precise inspection tasks. Order the gauge pin directly via Metav Werkzeuge or consult our advisors for application support. Gauge pin, single, 12.87 mm diameter — 50 mm length (Metav IndustryLine) The gauge pin, single, 12.87 mm, 50 mm length serves as a hardened reference for end‑dimension verification and precise fit checks in workshop and inspection environments High precision ±0.002 mm accuracy Special steel for dimensional stability 12.87 mm ground diameter, exact fit Delivered in protective transport case Consistent measurement where it matters The compact reference pin is engineered to deliver consistent, repeatable results in production and inspection routines. With a certified positional accuracy of ±0.002 mm, the pin minimises measurement uncertainty when checking bore diameters and mating parts. This level of control reduces rework and supports efficient quality assurance workflows, making the component a practical choice for routine in‑process inspection and final acceptance checks. Exact fit and practical handling for workshop use A ground diameter of 12.87 mm combined with a length of 50 mm provides a precise seating depth for end‑dimension assessments and insertion tests. The relatively low mass (0.1 kg) aids manual handling while the solid construction ensures dimensional stability during repeated use. Supplied in a protective transport case, the pin remains protected from handling damage and contaminants, preserving surface finish and tolerance integrity between uses. Integration into inspection processes and traceability Designed as a single gauge pin for targeted checks, this item is suitable for quick go/no‑go comparisons as well as documented inspection routines. The simple geometry and clear identification facilitate inventory control and traceability in the workshop. Combined with Metav’s quality filter and broad product portfolio, the pin supports streamlined purchasing and dependable replenishment for industrial measurement programmes. Contact Metav Werkzeuge today to discuss the M323.C87 gauge pin and secure a precise measurement solution tailored to workshop or inspection needs Technical data Article number: M323.C87 GTIN: 4061905065170 Label: Gauge pin, single, 12.87 mm length 50 mm Core data Diameter: 12.87 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Features Material: Special steel Version: Workshop execution Packaging: Protective transport case (plastic or wooden) Category: Gauge pins FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.C87 is specified with an accuracy of ±0.002 mm, suitable for tight tolerance inspections and repeatable fit checks. Is the pin suitable for routine go/no‑go checks? Yes. The single gauge pin is intended for quick insertion and go/no‑go verification in inspection processes and production control. How is the item delivered and protected in transit? The product is supplied in a protective transport case (plastic or wooden) to preserve the ground surface and dimensional integrity during storage and transport. Which materials is the pin made from and what does that mean for durability? Constructed from special steel, the pin offers dimensional stability and wear resistance appropriate for frequent workshop use. Can this pin be used for measuring end dimensions in bore checks? Yes. The 12.87 mm diameter and 50 mm length make the pin well suited to end‑dimension checks and seating tests in bore inspection applications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.88mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of precise end‑measurement control thanks to the combination of 12.88 mm nominal diameter, ±0.002 mm accuracy and a robust 50 mm working length in special steel for repeatable gauging. Order the test pin directly via Metav Werkzeuge or contact their consultants for application advice. Test Pin M323.C88 — 12.88 mm gauging pin, 50 mm length (Metav IndustryLine) The Test Pin M323.C88 is a compact gauging pin designed for precision end‑measurements and plug‑gauge checks in workshop and production inspection routines Precise 12.88 mm nominal diameter 50 mm hardened length for stability Tolerance ±0.002 mm for fine control Consistent measurement accuracy for quality control This gauging pin delivers a compact solution for repeatable end‑measurements by combining a nominal diameter of 12.88 mm with an achieved accuracy of ±0.002 mm. The tight tolerance reduces measurement scatter during pass/fail checks and comparative testing, which streamlines inspection steps and shortens quality gates. The pin form is ideal for checking bores and mating features where a stable reference diameter ensures reliable go/no‑go decisions. Robust construction for shop‑floor reliability Manufactured from special steel, the component offers the stiffness and wear resistance needed for frequent use in workshop environments. Its 50 mm overall length provides a secure engagement when inserted for plug‑gauge operations while keeping the centre of gravity low for easy handling. The workshop‑grade design supports routine use in production control without sacrificing dimensional stability, helping to reduce rework and downtime. Simple integration into inspection workflows Supplied as a single precision pin, the item fits into established gauging procedures and bench setups and is suitable for short, repeatable checks on components and assemblies. Identification via GTIN 4061905065187 and the clear article labelling facilitates inventory control and traceability in procurement systems. The compact weight and form factor make it straightforward to keep a set of reference pins at inspection points for fast comparative checks and documented quality routines. Contact Metav Werkzeuge for supply and technical matching — Metav Werkzeuge can advise on compatibility with existing gauging fixtures and ensure fast delivery from Emmerich Technical data Article number: M323.C88 GTIN: 4061905065187 Category: Test pins / Gauging pins Label: Test pin, single, 12.88 mm, length 50 mm eClass: 21170231 Facts Diameter: 12.88 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Workshop‑grade execution Material: Special steel Single piece supply Intended for end‑measurements and plug‑gauge checks FAQ What accuracy can be expected from this test pin? The M323.C88 delivers an accuracy of ±0.002 mm, making it suitable for fine inspection work and reliable pass/fail gauging in workshop and production environments. Is the pin suitable for plug‑gauge checks and bore inspection? Yes, the gauging geometry and 12.88 mm nominal diameter make the pin appropriate for plug‑gauge checks and short bore measurements as part of standard inspection routines. How is the item supplied and identified? The product is supplied as a single test pin (SKU M323.C88) and is identifiable via GTIN 4061905065187 for inventory and traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.89mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop robustness, fine dimensional accuracy and compact handling for consistent inspection results; order the pin directly via Metav Werkzeuge or consult the specialists for specification matching. Gauge pin M323.C89 — 12.89 mm diameter, 50 mm overall length (Metav IndustryLine) The Gauge pin M323.C89 is a single inspection pin designed for precise end‑dimension checks and fitting verifications in workshop and production environments. Workshop design for durable use Diameter precisely 12.89 mm Dimensional tolerance ±0.002 mm Supplied individually in a transport case Reliable dimensional control for routine inspection The M323.C89 delivers high repeatability by combining a compact geometry with a tight dimensional tolerance of ±0.002 mm, which corresponds to industrial fine‑measurement practice. Such a tolerance ensures that the pin functions as a dependable reference for end‑dimension checks, fitting trials and calibration of gauges. The solid construction reduces micro‑deformation during handling, so the measured result reflects the part, not the tool. Where clear pass/fail decisions are required, this level of precision supports efficient quality workflows. Engineered for workshop handling and long service life Built in a workshop specification, the pin is manufactured from special steel chosen for dimensional stability and wear resistance under typical shop conditions. The compact 50 mm overall length and low mass aid rapid manual use and reduce operator fatigue during repetitive checks. Delivered individually in a protective transport case, the item arrives ready for safe storage and mobility between bench and machine. The simple single‑piece design minimises handling complexity and supports routine cleaning and inspection. Practical uses and system compatibility Small‑diameter gauge pins such as this fall into the micro range (10–100 mm) and are therefore particularly suited to precise, small‑component work: bearings, housings, dowel fits and end‑face checks in assemblies. The pin serves as a go/no‑go reference, alignment aid or assembly gauge and integrates easily into existing measuring procedures. Traceable identification (SKU M323.C89) and stable geometry make it a useful companion to calipers, micrometres and bench gauges when an accurate physical datum is required. Choose the Metav IndustryLine gauge pin M323.C89 for dependable end‑dimension control — contact Metav Werkzeuge in Emmerich for procurement and technical guidance via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.C89 GTIN: 4061905065194 Manufacturer: Metav IndustryLine Category: Gauge pins / Messstifte Data Diameter: 12.89 mm Length: 50 mm Weight: 0.1 kg Dimensional tolerance: ±0.002 mm Special features Workshop version Material: Special steel Delivered individually in a transport case Single inspection pin for end‑dimension checks FAQ What is the exact diameter of this gauge pin? The pin has a diameter of 12.89 mm, specified for precision end‑dimension verification on the Metav IndustryLine gauge pin M323.C89. What tolerance can be expected from the pin? The dimensional tolerance is ±0.002 mm, providing fine measurement resolution suitable for workshop inspection tasks. Is the pin delivered ready for storage and transport? Yes — the product is supplied individually in a protective transport case to facilitate safe handling and storage between uses. Which applications are most suitable for this pin? Typical uses include end‑dimension checks, fitting and alignment tasks, go/no‑go references and small‑component assembly controls in mechanical workshops. How does this pin integrate with existing measuring tools? The M323.C89 complements calipers, micrometres and bench gauges as a physical reference or alignment aid; its stable geometry and SKU identification simplify incorporation into existing inspection procedures. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.8mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of precise workshop measurement with a durable pin that combines special steel construction and a fine ±0.002 mm tolerance for reliable end‑measure checks; order directly via Metav Werkzeuge or contact our consultants for specification advice. Gauge pin (single), 12.8 mm — 50 mm length, ±0.002 mm accuracy (Metav IndustryLine) Gauge pin (single) for end‑measurement tasks in workshop environments, combining compact handling with industrial repeatability Workshop design, robust for bench use Diameter 12.8 mm for end measurements Tolerance ±0.002 mm for precise checking Precision and what it means for measurement reliability The compact checking pin is specified with a diameter of 12.8 mm and an accuracy of ±0.002 mm. That tolerance corresponds to a deviation of two micrometres, which makes the pin suitable for high‑precision pass/fail checks and comparative gauging in component inspection. The clear, measurable specification reduces ambiguity in quality control procedures and supports reproducible results when used for end‑measurements or as a reference datum in short‑run checks. Robust material and practical handling for busy shops Manufactured from special steel, the pin is designed to withstand repeated use in a workshop environment while maintaining dimensional stability. At 50 mm length and approximately 0.1 kg weight, the component is easy to handle and compatible with common checking fixtures and bench setups. The item is supplied in a transport case to protect the surface finish during storage and transit, ensuring the gauge remains ready for immediate use without additional preparation. Integration into quality workflows and the Metav promise As a single checking pin from Metav IndustryLine, the product is intended for quick verification tasks and routine end‑measurement operations on production lines and in inspection stations. Clear identifiers (SKU M323.C80, GTIN 4061905067280) support traceability in inventory and documentation. Metav’s commitment to democratising precision means specialist tools like this are backed by straightforward supply from Emmerich and by decades of sourcing experience, helping to keep measurement standards consistent across workshops. For specification help or to secure supply of the Metav IndustryLine gauge pin (SKU M323.C80), contact Metav Werkzeuge directly at info@metav-werkzeuge.com or +49 2822 7131930 for prompt assistance and shipping from Emmerich Technical data Article number: M323.C80 GTIN: 4061905067280 SKU: M323.C80 Numbers / Core technical data Diameter: 12.8 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Special features / Design Material: Special steel Workshop version Delivered in transport case Single gauge pin for end measurements Category: Messstifte FAQ What applications is this gauge pin suitable for? The gauge pin is intended for end‑measurement checks and short‑range verification tasks; the Metav IndustryLine gauge pin (M323.C80) is commonly used for bench checking and pass/fail inspection. How precise is the measureability of the pin? The Metav IndustryLine gauge pin is specified to ±0.002 mm tolerance, equating to a two‑micrometre deviation suitable for fine comparative checks. Is the pin supplied protected for transport? Yes, the gauge pin is delivered in a transport case to preserve the surface and dimensional integrity during shipping and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.91mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
High repeatability and workshop-ready robustness combine in this precision plug gauge: the 12.91 mm diameter and ±0.002 mm tolerance deliver reliable end‑measurements, while the 50 mm shank length provides secure seating in fixtures. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge Pin M323.C91 — Single precision plug gauge, 12.91 mm, 50 mm length (Metav IndustryLine) The Gauge Pin M323.C91 is a single‑piece precision plug gauge designed for end‑measure checks and alignment tasks in workshop and inspection environments. Workshop version, robust design Diameter 12.91 mm for end measurements Tolerance ±0.002 mm for repeatable results Delivered in transport box for safe handling Precision where measurement consistency matters The plug gauge offers a finely controlled fit for end‑measurements thanks to its ±0.002 mm tolerance, ensuring consistent readings across repeat checks. As a single‑piece measuring element with a nominal diameter of 12.91 mm, it reduces uncertainty when verifying bore sizes, locating holes or checking assembly interfaces. The measurable benefit is fewer rework cycles and clearer go/no‑go decisions in quality control processes, deriving efficiency gains through predictable, comparable data. Built for workshop use and secure handling Manufactured in special steel and specified as a workshop‑grade item, the gauge pin combines surface hardness with the toughness required for everyday handling. The 50 mm overall length provides a stable engagement in fixturing and clamping applications without excessive overhang, supporting repeatable seating and alignment. For transport and on‑site protection the item is supplied in a transport box, which reduces the risk of damage during handling and keeps the measuring face free from contamination between uses. Practical applications and suitable measurement class This measuring plug belongs to the micro range (10–100 mm), making it ideal for precision tasks in toolmaking, fixture setup and component inspection where small diameters and tight fits are common. Typical uses include end‑measurement verification, fixture pinning, hole gauge checks and assembly verification. The compact geometry minimises bending and ensures a reliable reference when used as a locating element or for transfer checks in serial production environments. Reliable supply and professional backing from Metav As part of the Metav IndustryLine, the M323.C91 benefits from Metav’s quality filtering and close warehouse proximity in Emmerich, which supports dependable delivery and stock transparency. Metav’s broad range and experience reduce procurement complexity while providing auditability for industrial purchases. For specifications, batch availability or integration into existing inspection routines, the M323.C91 is documented and traceable within Metav’s assortment, supporting efficient workshop workflows. Contact Metav Werkzeuge for technical advice on the M323.C91 and swift supply from our Emmerich stock — expert consultants are available to support specification and compatibility checks. Technical Data Article number: M323.C91 GTIN: 4061905066313 Manufacturer: Metav IndustryLine Numbers / Core technical data Diameter: 12.91 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features / Materials Material: Special steel Workshop execution Supplied in transport box for protection Single‑piece plug gauge for end measurements FAQ What is the tolerance of this plug gauge? The M323.C91 plug gauge is specified with a tolerance of ±0.002 mm, suitable for repeatable workshop measurements. Which material is used for the gauge pin? This plug gauge is made from special steel and is offered as a workshop‑grade measuring element. Is the gauge pin supplied in protective packaging? Yes, the item is delivered in a transport box to reduce handling damage and keep the measuring surfaces protected. For which applications is this plug gauge best suited? Typical applications include end‑measurement checks, fixture locating, hole verification and alignment tasks in toolmaking and workshop inspection. Does the product include an ISO 17025 calibration certificate? The product data does not specify delivery with an ISO 17025 certificate; for certified calibration requests, Metav Werkzeuge can advise on available options. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.92mm Gauge Pin, Single, 50mm Length, Special Steel, Workshop Version - Metav IndustryLine
Compact workshop-grade gauge pin delivering reproducible end-measure checks thanks to 12.92 mm nominal diameter and ±0.002 mm tolerance; combined with a 50 mm length this makes for dependable routine verification. Order the part via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single, 12.92 mm, length 50 mm — Workshop-grade inspection pin (Metav IndustryLine) A gauge pin intended for precise end-measure verification and short-range reference tasks in production, inspection and workshop environments. Workshop-grade construction Nominal diameter 12.92 mm Length 50 mm for end measures High repeatability ±0.002 mm tolerance Consistent precision for end measurements The design offers ±0.002 mm repeatability, providing a reliable reference when checking end dimensions and mating fits. Manufactured as a compact inspection pin, it supports quick verification and calibration tasks on the shop floor; the tight tolerance reduces rework by ensuring measurements remain within the required window. This level of accuracy is particularly relevant where short-range end faces and bores must be confirmed repeatedly, giving a quantifiable basis for process decisions and traceable results. Durable workshop design that keeps performing Built in special steel and finished for workshop use, the component resists wear during frequent handling and insertion. The 50 mm length balances reach and rigidity: long enough for many end-measure jobs, yet short enough to avoid bending under normal use. The robust execution suits routine checking at assembly stations or inspection benches, where the part’s longevity and consistent surface condition maintain measurement integrity over time. Simple integration and practical handling The compact form factor and nominal 12.92 mm diameter make the item suitable for standard locating fixtures and simple gauge holders. The low mass and controlled geometry ease handling during batch inspections and spot checks, while the clear labelling and traceability support documentation of inspection routines. For bespoke fixture advice or integration into existing test jigs, Metav IndustryLine documentation and consultancy can assist with mounting options and usage recommendations. Contact Metav Werkzeuge for tailored technical advice and prompt supply of the Metav IndustryLine gauge pin M323.C92 directly from Emmerich; phone +49 2822 7131930 or e-mail info@metav-werkzeuge.com Technical Data Article number: M323.C92 GTIN: 4061905066320 Manufacturer: Metav IndustryLine Label: Prüfstift, einzeln, 12,92 mm Länge 50 mm Facts Diameter: 12.92 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop-grade execution Material: Special steel Category: Gauge pin FAQ What tolerance can be expected from this gauge pin? The gauge pin M323.C92 from Metav IndustryLine is specified with a tolerance of ±0.002 mm, suitable for fine workshop verification and repeatable end-measure checks. Is the pin suitable for routine shop-floor checks? Yes, the workshop-grade construction and 50 mm length make this inspection pin well suited to routine shop-floor verification tasks and short-range reference use. What material is used for the pin and how does that affect wear? The pin is made from special steel; this material choice combines dimensional stability with good wear resistance for frequent handling in inspection environments. Can this pin be used with standard locating fixtures? The nominal 12.92 mm diameter and compact form factor allow easy integration into common locating fixtures and simple gauge holders for quick verification tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.93mm Test Pin Length 50mm Workshop Version - Metav IndustryLine
Take advantage of precise diameter control, robust workshop design and a compact 50 mm length for reliable fixture and end‑dimension checks. Combine special steel construction with a tight ±0.002 mm runout for consistent inspection results. Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. M323.C93 test pin – 12.93 mm diameter, 50 mm length (Metav IndustryLine) The M323.C93 test pin is a precision gauge pin intended for end‑dimension inspection and fixture verification in metrology and workshop environments. Workshop‑grade construction Diameter 12.93 mm precision Compact 50 mm length for fixtures Tight runout tolerance ±0.002 mm Consistent measurement through tight tolerances A gauge pin with a nominal diameter of 12.93 mm and a specified runout of ±0.002 mm provides a predictable reference for go/no‑go fits and alignment tasks. The tight tolerance reduces cumulative error when used with mating components or in serial inspection setups, so measurements remain traceable and reproducible. Built from special steel, the pin resists wear under repeated insertion cycles, which supports long‑term repeatability and reduces the need for frequent replacement. Robust workshop design that fits routine use Designed as a workshop‑grade item with a 50 mm working length and a mass of approximately 0.1 kg, this single test pin balances stiffness and handling. The length is sufficient for most fixture checks while remaining compact enough for insertion into tight assemblies. The construction suits repeated manual handling and integration into gauge blocks or simple locating fixtures, offering a practical combination of lightweight operation and mechanical resilience for everyday quality control. Practical applications and workflow benefits The pin serves as a reference for end‑dimension inspection, assembly checks, and localisation in jigs and fixtures. When applied as a master datum or in matched sets, it streamlines inspection sequences by providing a standard physical gauge that complements optical and digital measuring devices. The compact format is especially useful where fast, reliable verification is required between machining steps, helping to shorten control loops and maintain production flow without complex setup changes. Request the Metav IndustryLine M323.C93 test pin via Metav Werkzeuge in Emmerich for dependable workshop inspection components or contact our advisors at info@metav-werkzeuge.com / +49 2822 7131930 to discuss compatibility with existing fixtures Technical data Article number: M323.C93 GTIN: 4061905066337 Brand: Metav IndustryLine Facts Diameter: 12.93 mm Length: 50 mm Tolerance / runout: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop model Single test pin Application: end‑dimension inspection and fixture checks FAQ What is the nominal diameter and tolerance of the test pin? The nominal diameter is 12.93 mm with a runout tolerance of ±0.002 mm for the M323.C93 test pin from Metav IndustryLine. Which materials is the pin suitable for checking? The M323.C93 test pin is intended as a dimensional reference for metallic and machined components; compatibility with specific materials depends on the inspection task rather than the pin material itself. How is the pin typically used in a workshop inspection routine? The pin is used for end‑dimension inspection, locating parts in fixtures and performing quick go/no‑go checks as part of in‑process or final inspection workflows. Is the M323.C93 supplied as a single item or in sets? This entry describes a single test pin supplied individually for integration into custom gauge sets or for standalone reference use. Can the pin be integrated with gauge blocks or fixtures? Yes, the compact 50 mm length and the precision diameter make the pin suitable for use with gauge blocks, locating fixtures and simple jigs to standardise repetitive checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.94mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop-grade durability, high-precision tolerance ±0.002 mm and a compact 50 mm length for reliable end‑dimension checks; order the item directly via Metav Werkzeuge or request guidance from our consultants. Test pin M323.C94 — measuring pin, 12.94 mm Ø, 50 mm length (Metav IndustryLine) The test pin M323.C94 is a single measuring pin designed for precise end‑dimension verification in workshop metrology and production control. Workshop version for robust use Diameter 12.94 mm for tight fits 50 mm overall length for compact checks Tolerance ±0.002 mm for high repeatability Precision where small deviations matter This measuring pin is engineered for applications in which repeatability and definable limits are decisive. With a nominal diameter of 12.94 mm and a verified tolerance of ±0.002 mm, the pin supports accurate end‑dimension checks and fits‑verification in gauges and fixtures. The combination of tight dimensional control and a short 50 mm overall length reduces lever effects during handling, making the measurement outcome more reliable and less prone to operator‑induced error. This is a rational choice where process stability and traceable results are required. Built for routine workshop use As a workshop version, the component is optimised for everyday handling and mechanical resilience. Constructed from special steel, the pin stands up to frequent insertion and withdrawal in checking fixtures without immediate signs of wear, which prolongs service intervals and lowers lifecycle costs. The compact form factor simplifies storage and handling in busy production environments while preserving the dimensional characteristics that matter for control charts and first‑article inspections. Integration into quality‑control workflows The design supports straightforward use in go/no‑go setups, fixture checks and end‑dimension verifications on assembly lines. Given its 12.94 mm nominal size and narrow tolerance band, the pin is suited to tasks such as final checks on turned parts, alignment of seating features and verification of mating bores. Its predictable behaviour enables efficient sampling plans and reduces rework by providing a clear, measurable reference point in inspection sequences. Handling, maintenance and documentation Careful handling extends useful life: avoid impact and contamination, and store the pin in a dry, clean environment. The special steel construction benefits from routine cleaning and light corrosion protection where required. For traceable quality assurance, keep records of inspection cycles and replacement intervals; the robust geometry and small mass make the pin easy to swap in modular gauge blocks or custom fixtures without affecting downstream measurements. For reliable workshop measurement with Metav IndustryLine precision, request the M323.C94 test pin from Metav Werkzeuge — our Emmerich‑based team can advise on availability and optimal use in existing inspection setups Technical Data Article number: M323.C94 GTIN: 4061905066344 SKU: M323.C94 Category: Messstifte Dimensions & Tolerance Diameter: 12.94 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Workshop version Material: special steel Designed for end‑dimension verification FAQ What is the exact diameter of the pin? The test pin M323.C94 has a nominal diameter of 12.94 mm, specified for tight‑fit checks. What tolerance does the pin meet? The measuring pin is specified with a dimensional tolerance of ±0.002 mm, ensuring high repeatability in workshop checks. Which length is supplied with the pin? This measuring pin is supplied with an overall length of 50 mm suitable for compact fixtures and quick inspections. What material is used for the pin? The component is manufactured from special steel, selected for durability in frequent measurement routines. For which inspection tasks is this pin suitable? The pin is intended for end‑dimension verification, seating and bore checks, and integration into go/no‑go fixtures where a 12.94 mm reference is required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.95mm Gauge Pin 50mm Length Workshop Version In Plastic Case - Metav IndustryLine
High repeatability from a ±0.002 mm tolerance and a compact 50 mm length combine with robust special steel construction for dependable end‑measurement in workshop environments. Delivered as a single reference pin and supplied ready for safe transport, this tool supports consistent gauge setting and quick pass/fail checks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.C95 — precision reference pin, ø 12.95 mm, length 50 mm (Metav IndustryLine) Gauge pin M323.C95 is a single precision reference pin for end‑measurement, gauge setting and inspection tasks in workshop and production metrology. Precision tolerance ±0.002 mm Diameter 12.95 mm, length 50 mm Special steel construction for durability Workshop version, delivered in transport box Reliable accuracy for routine inspection The M323.C95 is engineered to provide consistent dimensional reference for frequent checks. With a specified tolerance of ±0.002 mm, the pin supports repeatable pass/fail decisions and tight gauging tasks without elaborate setup. Its 12.95 mm nominal diameter and compact 50 mm length keep deflection minimal while allowing fast engagement in bores, gauges and fixture checks. For workshop environments where efficiency and traceability matter, this pin reduces cycle time for simple verification steps and minimises the need for temporary fixtures. Robust handling and prolonged service life Constructed from special steel, this single gauge pin resists mechanical wear from repeated insertion and withdrawal, helping to maintain dimensional integrity over many inspection cycles. The workshop‑grade finish is chosen for practical durability rather than delicate laboratory handling, making the pin suitable for frequent use at production benches. Supplied as an individual reference piece and protected in a transport case, the design balances ease of handling with protection during storage and movement between workstations. Practical integration into metrology workflows As a straightforward reference element, the pin is suitable for setting plug gauges, checking bore runout and confirming end‑measurements on subassemblies. Its compact form factor allows quick positioning in tight fixtures while the tight ±0.002 mm specification supports confident decisions in quality control routines. Where traceability or inventory management is required, the item’s SKU and GTIN enable seamless recording in inspection logs and procurement systems, ensuring the pin is recognised across workshop documentation and reorder processes. Contact Metav Werkzeuge to secure the Metav IndustryLine gauge pin M323.C95 for robust end‑measurement and reliable gauge setting in daily workshop operations Technical data Article number: M323.C95 GTIN: 4061905066351 Facts Diameter: 12.95 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop version Delivery: transport case for safe transport FAQ What applications suits this gauge pin? The gauge pin M323.C95 is intended for end‑measurement checks, setting plug gauges and quick bore verifications in workshop and production environments. What level of accuracy can be expected from this pin? The M323.C95 is manufactured to a tolerance of ±0.002 mm, providing high repeatability for routine inspection and gauge‑setting tasks. What material is the pin made from and how durable is it? This gauge pin is made from special steel and finished for workshop use; the material choice supports good wear resistance during repeated handling. Is the pin supplied individually and how is it packaged? The product is supplied as a single reference pin and delivered protected in a transport case to reduce handling damage during storage and transit. Can the pin be used to set gauges and record results in quality systems? Yes; the M323.C95 is suitable for setting plug gauges and can be referenced by its SKU and GTIN for traceability in quality control records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.96mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of precision, tight ±0.002 mm tolerance and workshop-grade durability for reproducible end-dimension checks; order the test pin directly via Metav Werkzeuge or consult our specialists for further application advice. Test pin M323.C96 — Gauge pin, 12.96 mm Ø, 50 mm length (Metav IndustryLine) A precision gauge pin intended for end-dimension and inspection tasks in workshop and metrology environments, offered as a single-piece instrument. Precision diameter 12.96 mm Tolerance ±0.002 mm Workshop-grade construction 50 mm length for deep checks Reliable accuracy for end-dimension verification The gauge pin is engineered for repeatable end-measurements where small deviations matter. With a nominal diameter of 12.96 mm and a verified tolerance of ±0.002 mm, the component provides a clear, measurable basis for go/no-go assessments and reference checks. Classified within the micro measurement range (max. 10–100 mm), this format balances compact handling with sufficient contact length to inspect small bores, seats and end faces. The given accuracy supports routine workshop quality control and critical dimensional verification without demanding specialised measuring machines. Durable construction and handling benefits Constructed from special steel, the pin is designed to withstand regular handling typical for a workshop-grade instrument. The 50 mm working length offers stable support during insertion and extraction, reducing the risk of tilting and measurement artefacts. At approximately 0.1 kg, the component combines tactile robustness with manageable weight for single‑hand operation or fixture mounting. The material choice and workshop execution minimise wear under normal use, ensuring consistent contact geometry and a long useful life for frequent inspection cycles. Traceability, identification and integration into workflows Supplied as a single item, the test pin carries clear identifiers for stock and process control: SKU M323.C96 and GTIN 4061905066368. These markers simplify inventory management and allow easy inclusion into measuring kits or gauge sets. The straightforward geometry of the pin makes it compatible with standard bench fixtures and depth gauges; when used as a reference element it simplifies documentation of end-dimensions and supports reproducible inspection routines. The compact form factor is particularly advantageous where space and quick handling are priorities. For procurement and application support relating to Metav IndustryLine gauge pins such as the M323.C96, contact Metav Werkzeuge for tailored advice and supply from Emmerich. Technical data SKU: M323.C96 GTIN: 4061905066368 Label: Test pin, single, 12.96 mm, length 50 mm Core dimensions Diameter: 12.96 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Materials & special features Material: special steel Workshop version Single-piece design Category: gauge pins FAQ What diameter and tolerance does this pin offer? The test pin M323.C96 has a nominal diameter of 12.96 mm with a stated tolerance of ±0.002 mm, suitable for precise end-dimension checks. Is the pin intended for fine mechanical or general workshop use? This gauge pin is classified in the micro range and is suitable for both fine mechanical inspection and everyday workshop quality control tasks where compact, repeatable checks are required. How is the product supplied for inventory and traceability? The product is supplied as a single item identified by SKU M323.C96 and GTIN 4061905066368 for straightforward stock control and documentation. What material is used and how does that affect durability? Manufactured from special steel, the pin is designed for workshop resilience and consistent contact geometry during repeated inspections. Can the pin be integrated into existing inspection routines? Yes, the simple geometry and standard dimensions of this gauge pin make it easy to integrate into fixtures, depth gauges and set-based inspection workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.97mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Benefit from the combination of ±0.002 mm dimensional accuracy, a special‑steel construction and a compact 50 mm length for reproducible end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin M323.C97 — single gauge pin, Ø 12.97 mm, 50 mm length (Metav IndustryLine) Gauge pin, single, Ø 12.97 mm, 50 mm length is a workshop‑grade measuring pin designed for precise end‑dimension verification and fixture set‑ups in inspection routines. Precision tolerance ±0.002 mm Robust special‑steel construction Compact 50 mm length for end‑measurements Precision for end‑dimension verification The Gauge pin M323.C97 delivers a nominal diameter of 12.97 mm with a tight tolerance of ±0.002 mm, making it suitable where repeatable end‑measurements are essential. The specification ensures consistent results when used as a reference plug in jigs, for bore checks or when verifying seating surfaces. By specifying a narrow tolerance, inspection routines gain measurable reliability, reducing uncertainty and supporting quicker go/no‑go decisions during quality checks. Built for the workshop: durability and handling Produced in a workshop execution, this measuring pin uses special steel to withstand everyday handling and the demands of a busy inspection bench. The 50 mm overall length keeps the pin compact and easy to position in confined setups while maintaining sufficient mass for stable seating. Delivered as a single unit in a transport box, the pin is protected during storage and transit, preserving the measuring surface and minimising downtime due to damage. Practical integration into metrology workflows Classified in the Mikro (10–100 mm) size range, the pin fits fine‑mechanical and general workshop applications where short, stiff gauge elements are preferred. Its compact dimensions and repeatable tolerance streamline integration into fixture layouts, go/no‑go assemblies and manual inspection steps. Clear identification via SKU and GTIN supports inventory management and traceability, contributing to efficient stock control and faster selection during routine inspections. Request Metav Werkzeuge’s Metav IndustryLine gauge pin M323.C97 for dependable ±0.002 mm end‑dimension control and assistance integrating it into workshop inspection kits Technical data Article number: M323.C97 GTIN: 4061905066375 Manufacturer: Metav IndustryLine Label: Prüfstift, einzeln, 12,97 mm Länge 50 mm Facts Diameter: 12.97 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Messbereich (max): 12.97 mm Special features Material: special steel Workshop execution Delivered in transport box for transport Category: gauge pins Single unit delivery FAQ What is the diameter and tolerance of the pin? The pin has a nominal diameter of 12.97 mm with a declared tolerance of ±0.002 mm for the Gauge pin M323.C97. Which material is used for this measuring pin? The gauge pin is made from special steel, specified for workshop durability and stable measuring surfaces. Is the pin suitable for bore and seating checks? Yes, the pin is intended for end‑dimension verification, including bore seating and fixture alignment tasks. How is the product supplied and protected? The item is supplied as a single unit and delivered in a transport box to protect the measuring surface during shipment. What size classification does this pin fall into? This measuring pin belongs to the Mikro (10–100 mm) range, suitable for fine‑mechanical and general workshop inspection work. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
12.98mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Benefit from a 12.98 mm precision pin with workshop‑grade construction and ±0.002 mm tolerance for consistent end‑measure checks; the item is supplied ready for transport in a protective case. Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.C98 — 12.98 mm diameter, 50 mm length (Metav IndustryLine) The test pin M323.C98 is a single precision gauge pin designed for workshop inspection and end‑measure verification, suited to go/no‑go fixtures and dimensional control tasks. Diameter 12.98 mm precision fit 50 mm hardened workshop length Special steel construction for durability Delivered in transport case Reliable dimensional control for repetitive checks A compact gauge pin with a 12.98 mm nominal diameter and a measured accuracy of ±0.002 mm provides a reliable reference for go/no‑go gauges and fixture seating. The tight tolerance reduces measurement scatter during repetitive checks, enabling faster decision cycles in production. Where consistent contact geometry matters, the precision fit of this pin minimises lateral play and supports repeatable seating without complex alignment procedures. Built for daily workshop use with durable materials The workshop specification and special steel construction translate into high wear resistance and long service intervals. At 50 mm overall length the pin balances handling and stability, making it straightforward to use in bench fixtures or portable check setups. The solid construction ensures inert behaviour under typical probe and gauge pressures, which reduces the need for frequent replacement and lowers total cost of ownership for routine inspection tasks. Easy integration and secure transport for organised workflows Supplied as a single pin in a protective transport case, the item is ready for immediate deployment or secure storage between shifts. The compact packaging protects the calibrated contact surface during handling and transport, helping to preserve the specified tolerance for longer. The single‑piece format suits modular gauge sets and is simple to combine with existing fixture plates, providing a practical, low‑complexity solution for repeatable end‑measure verification. Contact Metav Werkzeuge today to discuss the M323.C98 test pin and how its workshop specification and tight tolerance can be integrated into inspection routines — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.C98 GTIN: 4061905066382 ECLASS: 21170231 Facts Diameter: 12.98 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Special features Material: Special steel Version: Workshop execution Packaging: Transport case Category: Gauge pin (Messstifte) FAQ What tolerance can be expected from this test pin? The M323.C98 test pin (Metav IndustryLine) is specified with an accuracy of ±0.002 mm, making it suitable for fine workshop inspection and repeatable reference checks. Is the pin suitable for fixture and go/no‑go applications? Yes, the single‑piece M323.C98 gauge pin is designed for integration into fixture mounts and go/no‑go arrangements where a precise contact diameter is required. What material is used and how does it affect durability? Constructed from special steel, the pin offers enhanced wear resistance compared with untreated steel, supporting longer service life under regular workshop use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com