Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
14.62mm Inspection Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop-suited measuring solution that combines a 14.62 mm nominal diameter, a 50 mm length and a verified ±0.002 mm tolerance for repeatable end measurements; order the part directly via Metav Werkzeuge or consult the Metav team for specification support. Gauge pin, single — 14.62 mm diameter, 50 mm length (Metav IndustryLine) The single gauge pin designed for precise end measurements and everyday workshop use, offering a compact footprint and industrial-grade accuracy. Workshop-grade construction Diameter 14.62 mm precision fit Length 50 mm for compact setups Tolerance ±0.002 mm Precision that delivers reliable end-measure results This compact measuring element is engineered to support accurate end measurements where repeatability matters. The 14.62 mm nominal diameter and the ±0.002 mm tolerance specify the permitted deviation between manufactured units and establish the component’s suitability for close‑fit gauges and verification tasks. In practice, a tolerance of ±0.002 mm indicates a high level of dimensional control that reduces rework and accelerates inspection cycles, making this component appropriate for calibration jigs and small‑part test fixtures where tight clearances are common. Robust construction tailored to workshop conditions Manufactured from special steel, the pin is intended as a workshop‑version part that withstands routine handling and integration into test rigs. The chosen material supports dimensional stability under normal workshop stresses and contributes to long service life when used for repetitive locating or checking operations. The compact 50 mm length keeps the component easy to manoeuvre and mount in confined setups, while its single‑piece design simplifies storage and traceability in tool cabinets or inspection sets. Practical handling, traceability and system fit With a nominal 14.62 mm diameter and a short overall length, the pin is straightforward to insert, align and measure within gauge assemblies or as a reference mandrel. The product is supplied as a single item for flexible use in bespoke setups; the included GTIN facilitates inventory control and procurement workflows. Lightweight and small‑format, the component integrates cleanly into modular inspection stations and supports quick replacement without lengthy downtimes, improving throughput on the shop floor. Choose the Metav IndustryLine gauge pin for compact, high‑accuracy end measurements and contact Metav Werkzeuge in Emmerich for purchasing and technical guidance Technical data SKU: M323.E62 GTIN: 4061905068751 Material: Special steel Nominal diameter: 14.62 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Core measurements Diameter: 14.62 mm Length: 50 mm Weight: 0.1 kg Tolerance: ±0.002 mm Features Workshop version Single gauge pin Category: Gauge pins (Messstifte) GTIN for traceability FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 14.62 mm and a specified tolerance of ±0.002 mm for high repeatability. Is this component suitable for end‑measurement applications? Yes. The single gauge pin is intended for end measurements and small‑part checking in workshop and inspection contexts. What material is used and how does it affect use? The pin is made from special steel, which gives the part a robust workshop‑suitable construction and stable dimensional behaviour under normal handling. How is the item identified for procurement and inventory? The product is supplied with a GTIN (4061905068751) and the SKU M323.E62 to support ordering and stock management. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.63mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the ±0.002 mm accuracy and special steel construction for reliable fit checks and repeatable end‑measure verification in workshop environments; the compact 50 mm overall length and nominal 14.63 mm diameter make this gauge pin a practical choice for inline inspection and assembly control. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single, Ø 14.63 mm, 50 mm length — Workshop‑grade inspection pin, ±0.002 mm | Metav IndustryLine The gauge pin, single, Ø 14.63 mm, 50 mm length is a workshop‑grade precision inspection pin designed for end‑measure checks and fit verification in machining, assembly and inspection tasks. Workshop‑grade finish Diameter 14.63 mm nominal Tolerance ±0.002 mm 50 mm overall length Accurate control that reduces rework and inspection time A compact inspection pin with a nominal diameter of 14.63 mm and a specified tolerance of ±0.002 mm enables fast go/no‑go checks and precise reference measurements at the machine or test station. The tight tolerance reduces uncertainty during fit verification, which translates into fewer rejects and lower rework rates. For production lines and small‑batch workshops, this level of reproducibility supports consistent assembly quality without complex measuring devices. Robust construction for everyday workshop use Manufactured from special steel, this pin combines wear resistance with dimensional stability under typical shop conditions. The 50 mm length provides sufficient engagement for end‑measure tasks while keeping the tool easy to handle and store. The workshop version finish balances durability with cost‑effective manufacture, making the pin suitable for routine inspections, gauge sets and short‑run quality checks where a hardwearing surface and clear nominal size are required. Practical handling and integration into inspection routines The single gauge pin is compact and straightforward to use in pick‑and‑place checks, fixture set‑ups and manual gauging procedures. Its simple geometry permits quick comparison against mating bores or seats and can be paired with basic inspection equipment or inserted into block sets for more structured measurement sequences. The robust design and clear nominal dimension simplify operator training and speed up routine controls, helping maintain throughput without compromising accuracy. For workshop‑ready precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to discuss procurement of this gauge pin (SKU M323.E63) and suitability for specific inspection tasks. Technical data Article number: M323.E63 GTIN: 4061905068768 SKU: M323.E63 Weight: 0.1 kg Core dimensions and accuracy Nominal diameter: 14.63 mm Length: 50 mm Tolerance / accuracy: ±0.002 mm Features and applications Material: special steel Workshop‑grade finish Category: gauge pins (Messstifte) Typical use: end‑measure checks and fit verification FAQ What nominal diameter does this pin have? The gauge pin has a nominal diameter of 14.63 mm, suitable for checks of matching bores and seats. What accuracy is specified for the inspection pin? The inspection pin is specified with a tolerance of ±0.002 mm, enabling fine fit verification in workshop inspection tasks. Which material is used for the pin? This gauge pin is produced from special steel, chosen for wear resistance and dimensional stability in typical workshop conditions. For which applications is this gauge pin intended? The pin is intended for end‑measure checks, fit verification and simple go/no‑go inspections in machining, assembly and workshop quality control. What is the SKU for ordering and traceability? Order and traceability reference: SKU M323.E63 (GTIN: 4061905068768). Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.64mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, robust workshop construction and fine tolerance for dependable end-measure checks and fixture set-up. Order the gauge pin directly via Metav Werkzeuge or contact our consultants for compatibility advice and fast delivery. Gauge pin, single, 14.64 mm Ø, 50 mm length — Metav IndustryLine The Gauge pin, single, 14.64 mm Ø, 50 mm length is a workshop-grade end-measure pin designed for precise dimension checks, locating and fixture verification in inspection and production environments. Workshop-grade construction Diameter 14.64 mm for end-measure applications Accuracy ±0.002 mm Made from special steel Consistent accuracy for routine inspection A reliable gauge pin must deliver repeatable results under daily use; this workshop-version pin provides a stated accuracy of ±0.002 mm, enabling tight control in tolerance-critical checks. The solid cylindrical form and fixed length reduce variables during insertion and measurement, which translates into fewer re-measures and a more efficient inspection routine. For production lines and inspection benches the clear numerical accuracy offers a direct basis for process decisions and documentation. Built to withstand shopfloor demands Constructed from special steel, this gauge pin is specified for frequent handling and contact with various mating surfaces. The 50 mm length gives sufficient engagement for most end-measure tasks while remaining compact enough for quick positioning. The workshop execution emphasises mechanical robustness rather than delicate laboratory finishes, which helps to keep service intervals low and uptime high in machining and assembly environments. Practical use cases and handling benefits Designed as a single test pin, the component is suitable for hole checking, gauge stacks, locating operations and fixture alignment. The nominal 14.64 mm diameter matches end-measure reference sizes where precise fit and minimal play are required. Because the part is single, it integrates easily into existing gauge sets or bespoke test rigs and supports straightforward traceable measurements during first-article inspections or daily quality checks. Simple documentation and identification The item is supplied with identification data that eases stock-keeping and traceability: SKU M323.E64 and GTIN 4061905068775 simplify ordering and record-keeping. A measured mass of 0.1 kg and the combination of diameter and length make it straightforward to plan storage and handling on the calibration rack. Clear labelling and consistent material choice also support repeatable results in serial inspection tasks. Contact Metav Werkzeuge for a quotation or compatibility check on the Metav IndustryLine gauge pin M323.E64 — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.E64 GTIN: 4061905068775 SKU: M323.E64 Facts Diameter: 14.64 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution Single gauge pin for end-measure applications FAQ What applications suit this gauge pin best? The gauge pin is intended for end-measure checks, hole verification and locating tasks; the Metav IndustryLine gauge pin M323.E64 is therefore well suited to inspection benches and fixture set-up. How tight is the tolerance and what does it mean in practice? A tolerance of ±0.002 mm gives high repeatability for routine inspection; in practice the value indicates that the pin’s diameter deviates from nominal by no more than two micrometres. Is the gauge pin traceable for documentation? Yes, the item is supplied with clear identification (GTIN 4061905068775 and SKU M323.E64) to support traceability and inventory control. Can this pin be used directly in gauge sets and fixtures? The single-piece design and workshop-grade construction make it compatible with common gauge stacks and locating fixtures where a 14.64 mm diameter member is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.65mm Gauge Pin 50mm Length Workshop Version, Special Steel in Case - Metav IndustryLine
This gauge pin combines high repeatability with compact dimensions and robust workshop design — ideal for reliable end‑dimension checks in fine mechanical production. Benefit from ±0.002 mm tolerance and a 14.65 mm diameter finish for consistent fits. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. M323.E65 Gauge Pin — 14.65 mm Diameter, 50 mm Length (Metav IndustryLine) A gauge pin M323.E65 designed for precise end‑measurement and alignment tasks in workshop and inspection environments Precise 14.65 mm diameter fit Tolerance ±0.002 mm for fine inspection 50 mm length in special steel workshop version Accurate end‑dimension control for micro components The supplied test pin delivers precision where small tolerances decide part acceptance. With a nominal diameter of 14.65 mm and an indicated accuracy of ±0.002 mm, the component serves as a reliable reference for end‑measurement and fit verification in small assemblies. Classified in the micro range (10–100 mm), this product is particularly suitable for fine mechanical work such as instrument components and small housings. The tight tolerance reduces scrap and rework by providing a stable datum for repeatable checks. Workshop‑proof construction that withstands daily use Machined from special steel, the pin is engineered for durability in workshop conditions while retaining the fine finish required for gauge applications. The 50 mm overall length offers a convenient handling length without compromising stiffness, making measurements and fit checks straightforward during assembly or inspection. The compact mass supports quick manipulation on the bench and can be used with common fixture plates and alignment tools. The workshop version emphasises practical longevity and simple integration into existing quality routines. Practical applications and efficiency gains on the shop floor Used as a reference pin for end‑measurement, alignment, and component seating, this test pin helps streamline quality control processes. The dimension stability and repeatable fit facilitate fast go/no‑go checks, setup verification and alignment of mating parts, contributing to shorter inspection cycles and fewer production interruptions. As a single‑piece test pin, it is effective for both standalone checks and as a reference in comparative gauges, promoting consistent assembly outcomes and greater confidence in final part quality. Discuss batch availability and specification matching with Metav Werkzeuge to ensure the M323.E65 meets application requirements and production cadence Technical data Article number: M323.E65 SKU: M323.E65 GTIN: 4061905066603 Brand: Metav IndustryLine Core figures Diameter: 14.65 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Design & features Material: special steel Version: workshop execution Category: gauge pin / test pin Intended use: end‑dimension checks and alignment FAQ What tolerance does the gauge pin offer? The M323.E65 gauge pin is specified with an accuracy of ±0.002 mm, suitable for fine inspection and tight‑fit verification. Which materials is the pin suited for checking? The test pin itself is made from special steel and is intended as a dimensional reference for components made of various workshop materials during fit and alignment checks. Is this gauge pin suitable for watchmaking or micro‑mechanics? Yes — classified in the micro range (10–100 mm), the pin is designed for small parts and precision assemblies where compact, stiff references are required. How is the pin delivered and identified? Each item is supplied with the listed article details (SKU M323.E65 and GTIN) for clear identification and inventory tracking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.66mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of pinpoint accuracy, robust material choice and practical transport protection for dependable reference measurements in the workshop. The precise ±0.002 mm tolerance and compact 14.66 mm diameter make this probe ideal for repeatable end‑measurements; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.E66 — single inspection pin, 14.66 mm Ø, 50 mm length (Metav IndustryLine) The gauge pin M323.E66 is a single inspection pin designed for reliable end‑measurements and reference checks in workshop and inspection environments. High-precision ±0.002 mm tolerance Diameter 14.66 mm, length 50 mm Made from special steel for durability Delivered in protective transport case Reliable accuracy that reduces rework The compact probe offers a measured ±0.002 mm tolerance, which supports consistent reference measurements across production batches. Built for repeatability, the pin helps to minimise measurement variance during setup and inspection routines, which in turn reduces rework and saves machine time. The 50 mm working length provides sufficient engagement for many end‑measurement tasks while preserving stiffness, and the compact 14.66 mm diameter resists bending under normal contact forces, keeping readings stable and comparable. Robust construction for workshop environments Manufactured from special steel, the pin is specified for regular workshop use where surface durability and dimensional stability matter. The workshop version finish withstands handling and routine contact with fixtures and workpieces. For practical logistics, the item is supplied in a protective case to prevent transport damage and to keep reference surfaces clean until use. This combination of material and packaging supports longer service life and dependable performance during repetitive checks. Practical fit for inspection and tooling jigs As a single probe, the item integrates readily into simple go/no‑go stacks, fixture pins or manual checking routines. The geometry and hardness of the steel enable secure seating in locating bores and gauge blocks, making it suitable as a reference element for end‑measurements and alignment tasks. Where small end‑play and consistent contact surfaces are required, this probe is a compact, purpose‑built option that streamlines manual inspection workflows without complicating fixture design. Request supply from Metav Werkzeuge for immediate dispatch from Emmerich, or ask our consultants for specification and fitting advice tailored to the application. Technical Data SKU: M323.E66 GTIN: 4061905066610 Category: Gauge pins Workshop version Diameter: 14.66 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Material: Special steel Single probe pin Protective transport case included Intended for end‑measurements and reference checks FAQ What level of accuracy can be expected from this gauge pin? The gauge pin M323.E66 delivers an accuracy of ±0.002 mm, suitable for tight reference checks and repeatable end‑measurement tasks in the workshop. Which material is used for the pin and how does that affect durability? The pin is made from special steel, chosen for dimensional stability and resistance to wear in routine inspection use; this supports longer service life under regular handling. Is the gauge pin supplied ready for transport and use? Yes, the product is supplied in a protective transport case to prevent damage during shipping and to keep the measuring surfaces clean until deployed. Can this pin be used in fixture and jig locating applications? The probe is intended for reference and end‑measurement roles and is well suited to locating bores and simple fixture applications where a compact, rigid reference element is required. What is the product designation and who supplies it? This is the M323.E66 gauge pin from Metav IndustryLine, supplied and distributed by Metav Werkzeuge for workshop and inspection use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.67mm Gauge Pin 50mm Length Workshop Grade, Special Steel - Metav IndustryLine
Benefit from workshop-ready accuracy and sturdy construction: a single, workshop-grade test pin with a precise Ø 14.67 mm diameter, 50 mm shank length and a verified ±0.002 mm tolerance — ideal for repeatable end‑gauge checks. Order the item directly via Metav Werkzeuge or consult our technical team for matching inspection sets. Test pin M323.E67 — Single gauge pin, Ø 14.67 mm, 50 mm length (Metav IndustryLine) Test pin M323.E67 is a single, workshop‑grade gauge pin designed for precise end‑measurements and inspection applications in metrology environments Precision diameter Ø 14.67 mm, tolerance ±0.002 mm Length 50 mm for deep-seat measurements Workshop-grade special steel construction Delivered in protective transport case Repeatable measurement where tolerances matter The pin is engineered for consistent, repeatable checks, offering a nominal diameter of Ø 14.67 mm with a verified ±0.002 mm variation. Such tight tolerances place the component among tools used for fine inspection tasks in metrology and quality control, where component acceptance depends on repeatable outcomes rather than one-off readings. The design reduces measurement scatter, which streamlines throughput and lowers rework rates in batch inspection processes. Robust build for regular workshop use Manufactured in special steel and specified as a workshop‑grade execution, the pin tolerates the rigours of daily use without compromising dimensional stability. The material choice balances surface wear resistance with economical machinability, so the part maintains form under regular handling and seating in fixtures. The overall construction supports frequent insertion and withdrawal during tactile inspection routines common in maintenance, jigs testing and end‑of‑line checks. Practical geometry for inspection and end gauges With a 50 mm shank length, the component reaches into recessed features while keeping the handle or fixture clear, facilitating ergonomic measurement sequences and safer handling on the shop floor. The compact diameter/length ratio suits modular gauge blocks, go/no‑go fixtures and end‑dimension checks on turned or milled components. Because the item falls into the micro inspection class for gauges up to 100 mm, it is optimised for fine mechanical assemblies, small bearings and precision shafts where alignment and concentricity are critical. Ready for storage and integration in inspection workflows Supplied as a single test pin in a protective transport case, the item is immediately ready for integration into inspection kits and measuring benches. The SKU and traceable identifiers simplify stock keeping and replacement planning, while the workshop specification complements existing gauge sets. Backed by Metav’s distribution and technical advisory services from Emmerich, the component fits both retrofit and newly configured inspection lines, helping to democratise precise measurement for any sized workshop. Contact Metav Werkzeuge for tailored inspection sets, technical matching and ordering of Metav IndustryLine gauge pins directly from our Emmerich facility Technical Data Article number: M323.E67 GTIN: 4061905066627 Brand: Metav IndustryLine Facts Diameter: 14.67 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Materials & Special features Material: Special steel Workshop execution Supplied as a single gauge pin Delivered in a protective plastic or wooden transport case FAQ What applications suit this gauge pin best? This test pin M323.E67 (Metav IndustryLine) is ideal for end‑dimension checks, go/no‑go assemblies and fine inspection tasks on small mechanical parts where repeatable diametric measurement is required. Is the tolerance sufficient for precision assembly inspection? Yes; the ±0.002 mm tolerance specified for the M323.E67 meets the requirements for high‑precision workshop inspections and many quality‑control processes that demand narrow acceptance bands. How is the pin delivered and stored? The M323.E67 is supplied as a single pin in a protective transport case, enabling safe storage and straightforward integration into inspection kits. Can this pin be used with existing gauge blocks or fixtures? The geometry (Ø 14.67 mm, 50 mm length) is compatible with common modular fixtures and gauge block arrangements; check fixture seat dimensions to ensure full contact and alignment. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.68mm Gauge Pin 50mm Length Workshop Version, Hardened Special Steel - Metav IndustryLine
Take advantage of the compact workshop-grade design, special steel construction and high repeatability of ±0.002 mm for reliable end‑size checks; order the gauge pin directly via Metav Werkzeuge or consult the technical team for application advice. Gauge pin, single — Ø 14.68 mm / 50 mm length (Metav IndustryLine) A single gauge pin in a workshop‑grade design, intended for precise end‑measurement and fixture checks in the micro measurement range *Workshop-grade gauge pin design *Diameter 14.68 mm, precise fit *Length 50 mm for fixture use *Accuracy ±0.002 mm for fine inspection Compact construction for accurate end‑measurements This inspection pin is engineered for repeatable end‑size verification in confined assemblies. The Ø 14.68 mm diameter and 50 mm overall length offer a compact profile that minimises lever action and deflection, making it ideal where short, stiff probing elements are required. The specified tolerance of ±0.002 mm provides a clear technical basis for quality control and tool setting tasks; in practical terms this means measurable differences at the micron level are detectable and reproducible. A workshop‑grade gauge pin of this geometry reduces handling complexity during fixture alignment and end‑of‑line checks, enabling faster, more reliable inspection cycles. Material choice and surface finish that withstands shop use Made from special steel, the pin combines hardness with ductility to resist wear during repeated contact with mating bores and fixtures. The material selection supports good surface integrity after machining and, when properly maintained, extends service life under normal workshop conditions. The single‑piece construction minimises joints and potential play so that each measurement reflects the part rather than the gauge. For assemblies where consistent contact geometry matters, the robust material and finish reduce uncertainty and contribute to stable measurement results over many cycles. Integration into inspection routines and fixtures Designed as a practical gauge element for general workshop use, this pin serves both as a go/no‑go reference and as a precise locating dowel for fixture checks. Its micro range sizing (measuring range cap ~10–100 mm) makes it suitable for fine mechanical parts, small housings and precise alignment tasks common in toolroom and small‑batch production. The compact form permits simple clamping or seating in test rigs, and the clearly documented SKU M323.E68 and GTIN 4061905067426 simplify inventory and traceability. As a specialist gauge component, it complements broader inspection kits and supports consistent quality workflows when combined with calibrated measurement instruments. Contact Metav Werkzeuge for tailored advice on integrating this Metav IndustryLine workshop‑grade gauge pin (SKU M323.E68) into production checks and fixture setups Technical data Article number: M323.E68 GTIN: 4061905067426 Manufacturer: Metav IndustryLine Label: Prüfstift, einzeln, 14,68 mm Länge 50 mm Measurements Diameter: 14.68 mm Length: 50 mm Weight: 0.1 kg Accuracy: ±0.002 mm Features and materials Material: Special steel Version: Workshop execution Category: Gauge pin / inspection pin FAQ How precise is the gauge pin for end‑measurement tasks? The gauge pin offers an accuracy of ±0.002 mm, which makes the Metav IndustryLine single gauge pin suitable for fine inspection and reliable repeatability in fixture checks. Is the pin suitable for small, high‑precision components? Yes, with a diameter of 14.68 mm and a compact 50 mm length the pin is designed for the micro measurement range and for precision checks on small mechanical parts. What material is used and why is that important? Constructed from special steel, the pin balances wear resistance and toughness to preserve contact geometry during repeated use and to deliver stable measurement results. How does the SKU and GTIN help in workshop management? The SKU M323.E68 and GTIN 4061905067426 enable straightforward inventory tracking and traceability when the gauge pin is integrated into inspection sets or procurement systems. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.69mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of high measuring certainty with a tolerance of ±0.002 mm, a compact 50 mm working length and durable special steel construction for consistent end‑dimension verification in workshop environments; order the part directly via Metav Werkzeuge or consult our specialists if further technical guidance is required. Gauge pin M323.E69 — single test pin, Ø 14.69 mm, 50 mm length (Metav IndustryLine) Gauge pin, single, 14.69 mm, 50 mm length is a compact inspection pin designed for precise end‑dimension checks and fixture set‑up in production and workshop metrology Workshop version, robust design Diameter 14.69 mm Length 50 mm Tolerance ±0.002 mm Consistent measurement certainty for routine inspection The solid cylindrical gauge pin offers a clearly defined diameter of 14.69 mm and a working length of 50 mm, providing a compact instrument for fast end‑dimension verification. With a specification of ±0.002 mm, the pin supports fine tolerance checks and repeatable results in control operations. The geometry and tight tolerance reduce interpretation error and make the part suitable for go/no‑go testing, datum setting and comparative measurements in standard workshop processes. Durable construction tailored to workshop use Manufactured from special steel, this single test pin is intended for regular handling and integration into inspection routines. The workshop version highlights a focus on robustness and ease of use: the material choice balances hardness with resistance to wear, which preserves diameter integrity over multiple cycles. For bench and fixture use the sturdy design reduces the need for frequent replacement, helping maintain uptime in production and reducing variability in manual gauging tasks. Practical deployment in quality control and fixture set‑up The compact format and precise diameter make the pin well suited for checking small bores, verifying mating shaft fits and aligning components during assembly. Its single‑piece construction simplifies storage and identification in tool assortments, while the moderate mass supports stable handling during measurement. Where rapid visual or tactile verification is required, the component acts as a reliable reference for machinists and inspectors performing repetitive end‑dimension tests. For dependable end‑dimension verification, secure this Metav IndustryLine gauge pin through Metav Werkzeuge—our consultants can advise on integration into existing inspection routines and compatible fixture setups Technical data Article number: M323.E69 GTIN: 4061905067433 Eclass: 21170231 Facts Diameter: 14.69 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution Single piece design Category: Gauge pins / Messstifte FAQ What applications suit this gauge pin best? This gauge pin is intended for end‑dimension checks, bore verification and fixture alignment in workshop and production quality control; the M323.E69 from Metav IndustryLine is compact yet precise for these tasks. What level of accuracy does the test pin provide? The specification for the test pin is ±0.002 mm, which supports fine tolerance checks and repeatable inspection outcomes in routine metrology work. Which material is used for the pin? The pin is made from special steel, chosen to balance wear resistance and dimensional stability for frequent workshop use. Can the pin be used for both shaft and bore checks? Yes, its defined diameter and compact length make it suitable for checking mating shafts and small bores as part of go/no‑go or comparative inspections. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.6mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
The combination of compact dimensions, ±0.002 mm repeatability and robust special steel construction delivers dependable end‑measurement checks in the workshop; order the gauge pin directly via Metav Werkzeuge or contact their consultants for application advice. Gauge pin M323.E60 — 14.6 mm Ø, 50 mm length (Metav IndustryLine) The gauge pin M323.E60 is a single, precision test pin intended for end‑dimension verification and fine measurement tasks in workshop metrology. Precision tolerance ±0.002 mm Diameter 14.6 mm Length 50 mm Workshop version with special steel Consistent precision for repeatable end measurements The M323.E60 functions as a high‑precision reference for dimensional checks, offering a tolerance of ±0.002 mm that supports tight verification limits. Its compact diameter and measured length make it suitable for end‑dimension verification of shafts, bore gauges and mating parts where reproducibility matters. The tight specification reduces measurement uncertainty and simplifies pass/fail decisions in routine quality checks. Robust design that eases handling and storage Manufactured from special steel, this single gauge pin combines surface hardness with corrosion resistance suitable for regular shop use. The 50 mm length and substantial cross‑section provide stable seating in fixtures and gauges, while the compact format minimises handling errors during insertion and withdrawal. The workshop execution balances durability with practical ergonomics for repeated inspection cycles. Integration into inspection routines and tooling setups As a dedicated test pin, the item integrates easily into gauge sets, mandrel checks and fixture alignment procedures. The 14.6 mm diameter corresponds to standard bore and shaft sizes, enabling quick checks without extensive setup. Where traceable calibration is required, the pin’s high resolution supports supplementary verification steps within established quality processes and measurement plans. For precision end‑measure tasks, choose the Metav IndustryLine gauge pin M323.E60 — contact Metav Werkzeuge for ordering or to clarify fitment and batch availability at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.E60 GTIN: 4061905068737 Label: Prüfstift, einzeln, 14,6 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 14.6 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Workshop execution (Werkstatt‑Ausführung) Single gauge pin for end measurements Category: Messstifte FAQ What level of accuracy can be expected from this gauge pin? The gauge pin M323.E60 from Metav IndustryLine is specified at ±0.002 mm, providing high repeatability for fine inspection tasks and small‑part verification. Is the material suitable for frequent workshop use? Yes; the pin is made from special steel, selected for durability and resistance to routine wear in workshop inspection environments. Can this pin be used for checking bores and mandrels? The 14.6 mm diameter and 50 mm length make the M323.E60 suitable for quick bore checks, mandrel seating tests and alignment tasks in gauge fixtures. Does the product come with traceable calibration documentation? Calibration status is not specified for this listing; for calibrated items or certificates, please enquire about the specific M323.E60 batch and available documentation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.71mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of a compact, workshop‑ready gauge pin that combines high reproducibility with robust special‑steel construction; its tight tolerance of ±0.002 mm and compact 50 mm length support reliable end‑measure checks and fewer production rejections. Order the item directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin, single, Ø 14.71 mm, 50 mm length — Metav IndustryLine workshop version, ±0.002 mm accuracy A single gauge pin, Ø 14.71 mm and 50 mm long, intended for precise end‑measure checks in workshop metrology Workshop‑grade construction Exact Ø 14.71 mm nominal diameter Compact 50 mm length for tight checks Tolerance ±0.002 mm for repeatable results Precision where it reduces rework The short cylindrical reference provides unambiguous dimensional control for end‑measure and hole‑fit checks. With a specified tolerance of ±0.002 mm, the element supports clear pass/fail decisions that reduce non‑conformances and downstream corrective work. A gauge pin functions as a datum for verification: when fitted into a bore or mated to an assembly interface, it confirms whether manufactured parts meet the required end dimensions. The workshop configuration balances durability and handling to keep inspection routines fast and consistent. Compact format that improves handling and stability At 14.71 mm diameter and 50 mm length the component sits in the Micro class (10–100 mm), providing the stiffness needed for precise short‑range checks while remaining easy to position with one hand. The compact form reduces bending moment compared with longer pins and thus improves repeatability during serial checks or spot verifications. Supplied in a protective case, the unit stays clean and protected between uses, shortening setup time and ensuring readiness during inspection cycles. Durable construction and traceable identification Made from special steel for wear resistance, the pin withstands frequent contact and preserves dimensional integrity across repeated use, extending service life and lowering total cost of ownership. Catalogue identifiers and traceability are provided for inventory control: SKU M323.E71 and GTIN 4061905067457 assist in documentation and batch management. Specified weight and compact sizing make integration into routine quality control simple, while the precision rating supports reliable go/no‑go evaluation in machining and assembly environments. Choose the Metav IndustryLine gauge pin (SKU M323.E71) for dependable workshop checks and straightforward traceability — contact Metav Werkzeuge in Emmerich for procurement and technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.E71 GTIN: 4061905067457 Weight: 0.1 kg Material: Special steel Accuracy (tolerance): ±0.002 mm Type: Single gauge pin Diameter: 14.71 mm Length: 50 mm Dimensions & measurable data Diameter: 14.71 mm Length: 50 mm Measurement range: 14.71 mm Weight: 0.1 kg Special features Workshop version Supplied in protective case E‑class: 21170231 Category: Gauge pins (Messstifte) FAQ What is the nominal diameter and length of this gauge pin? The gauge pin is specified at a nominal diameter of 14.71 mm with a total length of 50 mm; the Metav IndustryLine item is catalogued as M323.E71. How precise is the measurement reference? This Metav IndustryLine gauge pin is manufactured to a tolerance of ±0.002 mm, providing high repeatability for end‑measure and fit checks in workshop environments. How is the pin delivered and protected in transit? The item is supplied protected in a case to preserve surface condition and dimensional integrity during storage and transport. For which inspection tasks is this pin best suited? The compact dimensions and high tolerance make it ideal for bore verification, end‑measure checks and assembly fit validation within the Micro measurement range (10–100 mm). How can the part be referenced in documentation or stock systems? Traceability is supported by the SKU M323.E71 and GTIN 4061905067457, which can be used in quality records and inventory lists. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.72mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of precision and compact dimensions together with durable special steel construction for reliable fixture verification. The small footprint and tight tolerance make this pin ideal for fine mechanical inspection and gauge stacks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.E72 — single test pin, 14.72 mm Ø | 50 mm length (Metav IndustryLine) The gauge pin M323.E72 is a single precision test pin designed for fixture and bore verification in workshops and small‑parts production. Single gauge pin, 14.72 mm diameter 50 mm length for fixtures Special steel for long service life Delivered in protective transport case Exceptional accuracy for fine mechanical checks The gauge pin is manufactured for demanding inspection tasks where small deviations matter. With a stated tolerance of ±0.002 mm, the pin supports repeatable pass/fail assessments and tight-fit verifications in assembly jigs and plug gauges. In practical terms, that accuracy minimises rework and reduces the need for repeated manual adjustments during setup. The compact geometry and short length favour stable seating in bores and holders, providing consistent contact and clear go/no‑go outcomes. Robust design intended for workshop environments Built as a workshop version, the test pin pairs a compact form with industrial durability. The use of special steel improves wear resistance under frequent insertion cycles and supports longevity on the production floor. The shaft finishes and diameter control aim to resist galling and preserve measurement integrity over time, which lowers replacement frequency and keeps inspection routines efficient. The item’s size class places it in the micro range (10–100 mm) category, making it particularly suited to fine mechanical components and small-bore checks. Practical handling and integration with inspection setups At 50 mm overall length and a diameter of 14.72 mm, the pin integrates smoothly into common fixture layouts and gauge stacks. Its manageable mass and stable seating reduce measurement scatter during manual handling, and the solid construction supports repetitive use in series testing. Supplied in a protective transport case, the pin arrives ready for storage and transport, guarding critical surfaces against damage and maintaining the calibrated condition expected for in‑house inspection tools. Contact Metav Werkzeuge for tailored advice and local supply from Emmerich — secure the Metav IndustryLine gauge pin for reliable workshop inspection and fixture validation Technical data Article number: M323.E72 SKU: M323.E72 GTIN: 4061905067464 Numbers / Core technical data Diameter: 14.72 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg ECLASS: 21170231 Special features Material: Special steel Version: Workshop execution Packaging: Protective transport case for delivery Intended use: Fixture and bore verification FAQ What level of accuracy does the pin provide? The gauge pin M323.E72 is specified with an accuracy of ±0.002 mm, suitable for tight tolerance checks in fine mechanical inspection. Which materials is the pin made from? This test pin is manufactured from special steel to improve wear resistance during repeated insertion and removal cycles. Is the pin suitable for use in small-bore fixtures? Yes, the pin’s 14.72 mm diameter and 50 mm length place it in the micro range (10–100 mm), making it appropriate for small‑bore and precision fixture work. How is the item supplied and protected? The product is supplied in a protective transport case to prevent damage to the measuring surfaces during handling and storage. Can this pin be used in gauge stacks and go/no‑go assemblies? The dimensional control and short length make it suitable for integration in gauge stacks and for go/no‑go verification in assemblies Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.73mm Gauge Pin Single 50mm Length Workshop Finish - Metav IndustryLine
Benefit from the combination of ±0.002 mm tolerance, special steel construction and a compact 50 mm length for precise end‑dimension checks; order the test pin directly via Metav Werkzeuge or consult our specialists if required. Test pin, Ø 14.73 mm — 50 mm length (Metav IndustryLine) Test pin 14.73 mm for workshop metrology and end‑measurement tasks across inspection fixtures and gauges Workshop‑grade construction Diameter 14.73 mm precision Tolerance ±0.002 mm Compact 50 mm overall length Repeatable precision for end‑dimension inspection The test pin is manufactured from special steel and finished to a tight ±0.002 mm deviation, providing reliable reference diameters for inspection, fixture set‑up and end‑measurement verification. The small form factor and precise diameter make this probe suitable for alignment checks and plug‑gage tasks where consistent contact geometry is essential. By reducing measurement scatter the component rejection rate falls and process stability improves, delivering clear cost‑efficiency in serial inspection. Robust workshop design that endures daily use Engineered as a workshop‑grade item, the probe combines wear‑resistant material selection with a compact 50 mm length to balance stiffness and handling. The relatively short shank limits bending and improves tactile control when fitted into holders or manual fixtures, while the special steel composition resists surface wear under typical workshop conditions. This durability translates into fewer replacements and predictable long‑term performance for routine production checks. Practical integration in inspection setups The probe’s defined diameter and short overall length simplify incorporation into go/no‑go fixtures, comparator stands and manual gauging systems. The precise diameter value of 14.73 mm allows repeatable seating in dedicated bushings or threaded adaptors, easing the creation of custom inspection aids. Traceability is supported through the provided SKU and GTIN, enabling inventory control and identification within structured quality systems. Contact Metav Werkzeuge in Emmerich for specification advice and supply of Metav IndustryLine test pins, and ensure the correct probe configuration for the measurement task at hand Technical Data Article number: M323.E73 GTIN: 4061905067471 Manufacturer: Metav IndustryLine Facts Diameter: 14.73 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg eClass: 21170231 Special features Material: Special steel Version: Workshop execution Label: Test pin, single, 14.73 mm length 50 mm Story trigger: end dimensions FAQ What applications is this test pin intended for? The test pin is intended for end‑dimension checks, fixture set‑up and insert gauges in workshop metrology, where a precise reference diameter is required. Is the tolerance of ±0.002 mm suitable for production inspection? Yes, the ±0.002 mm tolerance places this probe in a high‑precision category suited to demanding workshop and inspection tasks; Metav IndustryLine items are selected to support reproducible measurements. Which material is used and why does it matter? The pin is made from special steel, chosen for wear resistance and dimensional stability under repeated contact, which preserves measurement reliability over time. How is the product identified for ordering and inventory? Order and inventory using SKU M323.E73 and GTIN 4061905067471; these identifiers ensure correct procurement of the Metav IndustryLine test pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.74mm Gauge Pin Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of high repeatability and compact dimensions combined with workshop‑grade robustness for reliable end‑measure checks; order the gauge pin directly via Metav Werkzeuge or consult their advisors for application support. Gauge pin M323.E74 — Ø 14.74 mm, length 50 mm (Metav IndustryLine workshop version) The gauge pin M323.E74 is a single precision inspection pin designed for end‑measure verification and dimensional checks in workshop and production environments. Workshop execution, robust design Precision tolerance ±0.002 mm Diameter 14.74 mm, length 50 mm Supplied in protective transport case Small-part inspection with workshop precision Classified in the Micro category (measurement range within 10–100 mm), this inspection pin meets the needs of fine‑mechanical work where compact geometry and stiffness matter. The 14.74 mm nominal diameter and 50 mm usable length make the pin suitable for end‑measure checks and insertion gauges on small bores and seats. With a stated ±0.002 mm tolerance, the component offers a high level of dimensional certainty that supports consistent quality control on small batches and one‑off parts, reducing rework and ensuring parts meet drawing limits. Built for repeatable results in everyday production The pin is manufactured from special steel and executed as a workshop variant to withstand regular handling and inspection cycles. The material choice provides a balance of hardness and wear resistance without excessive brittleness, helping to keep gauge wear low over repeated use. Supplied in a protective transport case, the item travels and stores safely, preserving calibration drift and surface condition. These attributes contribute to repeatability in inspection workflows and allow quick comparisons against reference standards during routine checks. Integration into inspection routines and process control As an individual precision plug, the item integrates easily into existing measuring benches and manual inspection procedures. The compact form factor supports fast handling and straightforward seating in fixtures, making it a practical tool for production checks and incoming inspection. Traceability is ensured via the SKU and GTIN data provided with the product, and the robust execution supports frequent use in workshops where inspection reliability is a daily requirement. The single‑piece design keeps setup simple while delivering consistent contact geometry for reliable results. Contact Metav Werkzeuge GmbH in Emmerich to discuss the suitability of the Metav IndustryLine M323.E74 gauge pin for specific inspection tasks and to arrange supply directly from the European quality filter. Technical data SKU: M323.E74 GTIN: 4061905067488 Description: Gauge pin, single, 14.74 mm diameter, length 50 mm Weight: 0.1 kg Facts Diameter: 14.74 mm Length: 50 mm Tolerance: ±0.002 mm Measurement range class: Micro (10–100 mm) Special features Material: Special steel Version: Workshop execution Delivery: Protective transport case Single gauge pin (individual article) FAQ What are the nominal dimensions of this inspection pin? The M323.E74 gauge pin has a nominal diameter of 14.74 mm and an overall usable length of 50 mm. How precise is the plug for end‑measure checks? The inspection pin is specified with a tolerance of ±0.002 mm, providing high precision for dimensional verification in workshop environments. What material is used for the pin? The pin is made from special steel, selected for durability and stable contact geometry under regular use. Is the gauge pin supplied ready for safe transport and storage? Yes, the item is delivered in a protective transport case to preserve surface condition and reduce handling damage during storage and transit. Can this pin be used for small bore gauging and seat checks? The compact dimensions and micro‑class measurement range make the pin suitable for small bore gauging, seating controls and other end‑measure verifications Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.75mm Test Probe 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a compact, workshop-ready gauging solution that combines tight dimensional control and robust construction; the 14.75 mm diameter and ±0.002 mm tolerance support repeatable end‑dimension checks, while direct ordering via Metav Werkzeuge keeps supply straightforward and reliable. Test pin M323.E75 – Gauge pin, 14.75 mm Ø, 50 mm length (Metav IndustryLine) The test pin M323.E75 is a single gauge pin for precise end‑dimension checks and alignment in workshop metrology. 14.75 mm diameter for precise fits High accuracy ±0.002 mm tolerance Workshop design in special steel 50 mm length for end‑dimension checks Precision for reliable end‑dimension checks A compact gauge pin with a nominal diameter of 14.75 mm and an indicated tolerance of ±0.002 mm provides a measurable advantage when verifying bore sizes, seatings and end dimensions. The tight tolerance reduces uncertainty in pass/fail decisions and shortens inspection cycles, so production and quality teams benefit from faster, more consistent results. The solid geometry of the pin supports accurate contact geometry for quick visual and tactile verification. Built for workshop resilience and repeatability Designed as a workshop execution, the unit is manufactured from special steel to withstand frequent handling and repeated seating operations. The 50 mm length gives sufficient engagement for end‑dimension checks and alignment tasks while remaining easy to position in fixtures or jigs. Low mass contributes to simple handling during serial inspections and the overall construction supports dependable endurance in daily use. Practical handling and integration into inspection routines Supplied as a single item, the pin is suitable for insertion into existing gauging sets or for use as a reference probe in dimensional checks. With a listed weight of 0.1 kg and the compact footprint typical of plug gauges, the component integrates into bench inspection procedures without adding complexity. Metav IndustryLine’s European distribution and product range make it straightforward to match the pin to compatible fixtures and measuring programmes, supporting both workshop throughput and traceable quality routines. Contact Metav Werkzeuge in Emmerich for tailored technical advice and to reserve the M323.E75 gauge pin for immediate workshop supply Technical Data Article number: M323.E75 GTIN: 4061905068430 Brand: Metav IndustryLine Category: Messstifte Facts Diameter: 14.75 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop execution Delivery: single item Intended use: end‑dimension checks and alignment FAQ What inspections is this pin suitable for? The M323.E75 gauge pin from Metav IndustryLine is intended for end‑dimension checks, alignment verification and plug‑style gauging in workshop inspection routines. How precise is the diameter of the pin? The listed diameter is 14.75 mm with a tolerance of ±0.002 mm, which supports consistent pass/fail assessment in production checks. Can the pin be used with standard fixtures and jigs? Yes, the gauge pin’s compact form and standard nominal diameter make it compatible with common fixtures and bench gauging setups used in workshop metrology. Is the material suitable for frequent handling? The component is made from special steel and specified as a workshop execution to provide resilience under regular handling and inspection cycles. How is the item supplied and identified? The item is supplied as a single test pin and is identified by article number M323.E75 and GTIN 4061905068430 for inventory and traceability purposes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.76mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of high repeatability (±0.002 mm), robust special‑steel construction, and compact 50 mm length for reliable end‑size verification in production and inspection. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single, 14.76 mm (50 mm length) – Metav IndustryLine The gauge pin, single, 14.76 mm (50 mm length) is a workshop‑grade precision plug used for end‑size checks, alignment and go/no‑go verification in inspection jigs and assembly fixtures. ±0.002 mm calibration tolerance 14.76 mm precision gauge diameter 50 mm special‑steel, workshop version Accurate reference for end‑size verification This workshop gauge serves as a compact, traceable reference for dimensional checks where repeatability matters. With a specified deviation of ±0.002 mm, the pin is suited to fine inspection tasks and production sampling where small tolerances determine fit and function. The stated tolerance reduces uncertainty in pass/fail decisions and shortens decision cycles on the shop floor, helping to avoid rework. The hardened, machined surface provides consistent contact conditions for measuring holes, bores and bores in mounting plates, translating a technical specification into dependable daily results. Robust geometry for stable handling and fixturing Constructed from special steel and offered in a 50 mm shaft length, this gauge balances stiffness and accessibility: the diameter provides a stable datum while the shaft length keeps the element easy to position in fixtures or soft jigs. The compact format reduces deflection during handling, which supports repeatable measurements in serial testing. The workshop execution emphasises durability in everyday environments, resisting wear under normal inspection loads and maintaining surface integrity that is critical for reliable contact measurement. Designed for integration into inspection workflows The pin functions as a precise go/no‑go or reference gauge within existing inspection setups and is particularly useful for end‑of‑line checks and assembly verification. Its clear identification (SKU M323.E76) and GTIN allow straightforward inventory management and ordering. As a single‑piece gauge, it is simple to handle, store and replace in fixture arrays. For operations seeking reproducible pass/fail criteria or a compact reference element for jigs, this plug gauge offers a straightforward and effective solution that complements broader metrology routines and quality systems. For tailored advice on integrating the Metav IndustryLine gauge pin into inspection fixtures or for bulk supply enquiries, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss specifications and delivery options. Technical Data Article number: M323.E76 GTIN: 4061905068447 Label: Prüfstift, einzeln, 14,76 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 14.76 mm Length: 50 mm Weight: 0.1 kg Deviation / tolerance: ±0.002 mm Special features Workshop version Material: special steel Category: gauge pins (Messstifte) Single gauge pin design FAQ What accuracy can be expected from this gauge pin? The Metav IndustryLine gauge pin offers a stated deviation of ±0.002 mm, providing the repeatability required for fine end‑size verification and reliable go/no‑go checks. Is the material suitable for everyday workshop use? Yes, the pin is manufactured from special steel in a workshop execution that prioritises durability and resistance to normal inspection wear. Which applications suit a 14.76 mm gauge pin with 50 mm length? The pin is ideal for hole and bore verification, fixture alignment and end‑size checks in assembly and inspection workflows where a compact, stiff reference element is needed. How is the product identified for reordering or inventory? The gauge pin is listed under SKU M323.E76 and GTIN 4061905068447 for straightforward procurement and stock control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.77mm Gauge Pin Length 50 mm Workshop Version, Special Steel ±0.002 - Metav IndustryLine
Take advantage of workshop-grade construction and a tight ±0.002 mm tolerance for reliable end-measure checks; the compact 50 mm length and 14.77 mm diameter provide repeatable positioning and easy handling. Order direct through Metav Werkzeuge or contact the consultants for application advice. Gauge pin (single) Ø 14.77 mm, 50 mm – Metav IndustryLine The Gauge pin (single) Ø 14.77 mm, 50 mm is a workshop-grade inspection pin designed for precise end-measure verification and integration into gauge sets. Workshop-grade construction Diameter 14.77 mm for end-measure checks Tolerance ±0.002 mm for repeatable verification Accurate results for routine inspection Built for measured repeatability, this inspection pin delivers a ±0.002 mm tolerance that supports reliable pass/fail checks and dimensional verification. The compact 50 mm length keeps deflection low and eases handling in cramped jigs, while the precise diameter ensures consistent seating in bores and fixtures. Presented as a single-piece gauge, the component suits production sampling and incoming part inspection where quick, reproducible readings are required. The combination of measured tolerance and compact form reduces rework and speeds decision-making on the shop floor. Durable, workshop-suitable construction Manufactured from special steel, the pin is finished for routine use in workshop environments without sacrificing dimensional stability. The workshop-grade execution gives abrasion resistance and maintains geometry under normal handling, making the item suitable for frequent checks within assembly or machining cells. Where items are used repeatedly, the material choice limits wear and preserves the critical diameter over many cycles, increasing mean time between replacements and supporting continuous production. Easy integration and traceable checks The pin is compatible with standard gauge sets and inspection fixtures, enabling straightforward incorporation into existing quality procedures. Its size and form factor are optimised for end-measure tasks and handheld checks, while the tight tolerance supports statistical process control when used as a reference artefact. Documentation and traceable measurement practice are easily maintained when the pin is adopted in a calibrated workflow, supporting consistent quality records and supplier audits. Contact Metav Werkzeuge in Emmerich for supply or technical advice on the Metav IndustryLine gauge pin with 14.77 mm diameter and ±0.002 mm tolerance Technical data Article number: M323.E77 GTIN: 4061905068454 Brand: Metav IndustryLine Facts Diameter: 14.77 mm Length: 50 mm Tolerance/accuracy: ±0.002 mm Weight: 0.1 kg Special features Material: special steel Workshop execution Single-piece gauge pin Intended use: end-measure checks and gauge sets FAQ What is the intended use of this gauge pin? The gauge pin is intended for end-measure verification and integration into gauge sets; the Metav IndustryLine gauge pin M323.E77 is suited to routine workshop inspection. How precise is the diameter of the pin? The diameter is specified at 14.77 mm with a tolerance of ±0.002 mm, providing the precision required for repeatable verification. Which material is used for the pin? The pin is made from special steel, selected for durability and dimensional stability during repeated use. Can the pin be used in standard gauge sets and fixtures? Yes, the format and length make the pin compatible with common inspection fixtures and gauge sets for end-measure tasks. Is this pin suitable for frequent shop-floor checks? Yes, the workshop-grade construction and material selection make the Metav IndustryLine pin suitable for frequent handling and production sampling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.78mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of high form accuracy (±0.002 mm), special steel construction, and a compact 50 mm length for reliable end‑measure checks. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single — 14.78 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin, single, 14.78 mm diameter and 50 mm long, designed for precise fit and end‑measure verification in inspection and workshop applications Workshop version for daily use Nominal diameter 14.78 mm, high form accuracy Length 50 mm for standard end‑measure checks Accuracy ±0.002 mm for tight tolerances Consistent accuracy for reproducible fits The cylindrical gauge provides a reliable reference for end‑measure inspections, seating checks and go/no‑go verifications in production and assembly. Manufactured from special steel, the pin maintains dimensional stability under repeated use while the specified accuracy of ±0.002 mm ensures that mating parts meet narrow tolerance bands. This makes the item particularly suitable for tasks where repeatability and traceable fit are decisive, such as final inspection of turned bores or checking locating holes in fixtures. Built for workshop robustness and easy handling As a workshop version, the test pin combines a compact 50 mm length with a nominal diameter of 14.78 mm, providing a balance between reach and rigidity that simplifies handling at the bench. The material choice offers wear resistance for extended service life, reducing replacement frequency and downtime. The straightforward geometry enables quick insertion into locating features and easy visual assessment of clearance or interference, supporting faster quality decisions on the shop floor. Practical integration into inspection routines The cylindrical gauge is designed for direct use in standard metrology workflows and is compatible with common fixture and height‑gauge setups. Traceable measurement results are facilitated by the high form accuracy and stable material properties, helping to shorten setup time during batch checks. As a precise reference element, it supports process control measures that reduce scrap and rework, contributing to more efficient production and consistent product quality. For dependable end‑measure checks and workshop readiness, select the Metav IndustryLine M323.E78 gauge pin from Metav Werkzeuge — contact our Emmerich team for application guidance or ordering details Technical data Article number: M323.E78 GTIN: 4061905068461 Weight: 0.1 kg Material: Special steel Facts Diameter: 14.78 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Special features Workshop version Single gauge pin Compact cylindrical geometry FAQ What is the intended use of this gauge pin? The M323.E78 from Metav IndustryLine is intended as a precision reference for end‑measure checks, fit verifications and routine go/no‑go seating tests in workshop and inspection environments. Is the material specified for long service life? Yes, the pin is made from special steel, selected to provide wear resistance and dimensional stability for repeated use in production checks. How tight is the specified tolerance? The pin is produced to a form accuracy of ±0.002 mm, suitable for tight tolerances in precision assemblies and finishing operations. Which SKU should be ordered for this exact size? Order SKU M323.E78 to obtain the 14.78 mm diameter, 50 mm length gauge pin from Metav IndustryLine. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.79mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precision, workshop-grade durability and a compact format to streamline end-of-line inspections; the tight ±0.002 mm tolerance reduces rework and ensures repeatable checks. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Inspection pin, single — 14.79 mm Ø, 50 mm length (Metav IndustryLine) Inspection pin, single — 14.79 mm Ø, 50 mm length designed for end-measurements and shop-floor verification in production and quality-control environments Gauge pin Ø 14.79 mm, length 50 mm Workshop-grade special steel construction Tight tolerance ±0.002 mm for precision Single-pin format for end-measurements Precision where it matters The gauge pin is manufactured for consistent dimensional checks: with a nominal diameter of 14.79 mm and a verified tolerance of ±0.002 mm, it provides the narrow error band required in fine inspection tasks. Such a tight specification improves repeatability during routine checks and reduces the risk of false rejects. In practice, this means fewer adjustments on machining centres and more reliable GO/NO‑GO decisions when verifying end dimensions. Robust workshop design for regular use Constructed from special steel, the pin is optimised for regular handling and resistive wear on contact surfaces. The 50 mm usable length balances ease of handling with adequate engagement for most plug-type or end-face checks, while the compact mass supports quick manual positioning. The workshop execution emphasises durability over cosmetic finish, so the component is suited to daily shop-floor use where mechanical robustness is essential. Practical integration into inspection routines As a single inspection pin, this item is intended for targeted end-measurements and alignment checks during setup, assembly or final inspection. Its precise diameter makes it suitable as a master reference in gauging fixtures or as a go/no-go reference for bore and seat checks. The compact format simplifies storage in tool cabinets and rapid exchange in measurement benches, supporting faster throughput without compromising measurement certainty. Confidence from a specialist supplier Supplied under the Metav IndustryLine, the pin benefits from the supplier’s quality filter and broad product range. Metav’s approach—making precision accessible—means the component arrives as part of a dependable sourcing chain, backed by a company that serves thousands of customers across industry and trade. Choosing a workshop-grade pin from a known supplier supports consistent procurement and traceability in quality systems. For application-specific advice or to request supply of the Metav IndustryLine inspection pin M323.E79, contact Metav Werkzeuge for expert guidance and reliable delivery from Emmerich: info@metav-werkzeuge.com • +49 2822 7131930 Technical data Article number: M323.E79 GTIN: 4061905068478 Brand: Metav IndustryLine Category: Gauge pins Facts Diameter: 14.79 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.10 kg Special features Material: special steel Workshop execution Single-pin format for end-measurements Intended use: end and reference measurements FAQ What level of accuracy can be expected from this inspection pin? The inspection pin is specified with a ±0.002 mm tolerance, providing high repeatability for end-measurements and close-tolerance checks. Is the gauge pin suitable for routine workshop use? Yes. The workshop-grade special steel construction and compact 50 mm length make the pin resilient for daily handling and regular inspection workflows. Which applications is this pin best suited for? Typical uses include end-face verification, seating checks, alignment setups and use as a reference in simple gauging fixtures during production control. Does the product include a calibration certificate? No ISO 17025 calibration is indicated for this item in the data provided; standard factory verification is applied. For certified calibration options, Metav Werkzeuge can advise on available services. How does this pin support measurement traceability? Delivered under the Metav IndustryLine, the pin is part of a documented supply chain; pairing the component with internal inspection records supports traceable measurement routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.7mm Test Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Taking advantage of precise fit and stable geometry, the inspection pin delivers consistent reference points for jigging and end‑measure checks; its 14.7 mm diameter and 50 mm length combine with a tight ±0.002 mm tolerance to reduce setup time and rework. Order via Metav Werkzeuge or contact their consultants for supply and technical advice. Inspection pin M323.E70 — datum pin, 14.7 mm Ø, 50 mm length (Metav IndustryLine) The Inspection pin M323.E70 serves as a precision datum and reference dowel for alignment, end‑measure verification and fixture positioning in machine shops and metrology workbenches. Workshop-grade construction Ø 14.7 mm datum pin, 50 mm length Special steel for dimensional stability Tolerance ±0.002 mm for fine checks Precise reference points that speed up set‑ups The inspection pin is manufactured to a ±0.002 mm tolerance, which places it in the range required for fine dimensional checks and tight fixture references. With a nominal diameter of 14.7 mm and a nominal length of 50 mm, the component provides a reproducible contact surface for end measurements and alignment tasks. The high repeatability of the datum surface reduces the need for frequent readjustment and shortens machine set‑up cycles, delivering clear efficiency gains in batch and single‑piece production. Built for the workshop: stable form and handling Designed as a workshop‑grade datum element, the pin is fabricated from special steel to preserve geometry under regular handling. The moderate mass (approx. 0.1 kg) and compact shape make it easy to position and clamp in jigs or toolholders, while maintaining dimensional stability during repeated use. This combination of robustness and precise manufacturing helps maintain consistent seating and contact, which in turn supports reproducible measurement outcomes and reduces scrap caused by misalignment. Integrates into inspection and fixture workflows As a compact gauge element, the pin adapts to quality control, toolmaking and fixture production tasks where a reliable reference is required. It is suitable for alignment, end‑stop definition and positional referencing in mechanical assemblies and gauges. Traceability and clear identification ease stock management and replacement planning, supporting continuous production and predictable maintenance cycles. When a stable datum pin is required for repetitive measurements, this Metav IndustryLine component provides a practical balance between rigidity and handling convenience. For availability and technical consultation on the Metav IndustryLine inspection pin M323.E70, contact Metav Werkzeuge for stock information and application advice at +49 2822 7131930 or info@metav-werkzeuge.com Technical Data SKU: M323.E70 GTIN: 4061905067440 Category: Messstifte Manufacturer: Metav IndustryLine Facts Diameter: 14.7 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.1 kg ECLASS: 21170231 Special features Material: Special steel Workshop version Single inspection pin, individual item FAQ What accuracy can be expected from this inspection pin? The inspection pin is manufactured to a tolerance of ±0.002 mm, making it suitable for fine checks and high‑precision reference uses. What material is used for the pin and what benefit does it bring? The pin is made from special steel, which provides dimensional stability and mechanical robustness for repeated seating and handling. Which workshops or processes is this pin intended for? Typical applications include machine shops, fixture and jig construction, and quality control workbenches where stable datum points are needed for alignment and end‑measure verification. Can this component serve as a datum for fixture positioning? Yes, the pin is designed as a datum/reference dowel and is suitable for defining end‑stops and positional references in gauges and fixtures. How is the item identified for procurement and inventory? Identification can be made via SKU M323.E70 and GTIN 4061905067440 for ordering and inventory control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.81mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial precision, robust special steel construction and compact handling for reliable end‑measurement operations; order the gauge pin directly via Metav Werkzeuge or consult the technical team for application advice. Gauge Pin M323.E81 — 14.81 mm diameter, 50 mm length (Metav IndustryLine) A Gauge Pin M323.E81 designed as a workshop‑grade measuring dowel for end‑measurements, fixture checks and reference gauging in production and inspection environments. High-precision 14.81 mm diameter Hardened special steel construction 50 mm length for secure seating and reach Workshop version for robust everyday use Accuracy that speeds up inspection cycles The compact measuring dowel delivers a verified ±0.002 mm form tolerance, translating into repeatable reference points in go/no‑go checks and fixture set‑ups. This level of precision reduces rework by making first‑pass inspections more reliable; integrating a precise dowel into routine checks shortens decision time at the gauge table and supports consistent assembly quality. The measured tolerance is particularly relevant where tight fits and concentricity matter, so the component serves as a dependable datum in production workflows. Material and durability engineered for the shop floor Manufactured from special steel and finished for workshop resilience, the dowel withstands frequent handling and the abrasion typical of fixture work. The material choice balances hardness with fatigue resistance to maintain diameter stability over repeated insertions. The result is a tool that retains measurement integrity and reduces the frequency of replacement, supporting steady productivity and lowering lifecycle costs for inspection equipment. Practical design for reliable handling and fixturing With a nominal diameter of 14.81 mm and a 50 mm length, the dowel offers sufficient length for stable seating while remaining easy to position by hand or with simple clamping devices. The single‑piece supply format is ideal for selective use as a reference pin or as part of modular inspection kits. Its geometry supports quick insertion into bores, pins and gauge blocks, enabling efficient set‑up times and less time spent aligning temporary fixtures during batch checks. Traceability and industrial readiness The product is supplied with identifiable data (GTIN available) and is produced under the Metav IndustryLine specification for workshop tools, ensuring consistent manufacturing standards between batches. This traceability supports quality documentation and inventory management in medium‑ to large‑scale production environments, where identifiable parts simplify replacement and audit processes. For tailored advice on integrating the Metav IndustryLine gauge pin with your inspection routines or to request delivery from Metav Werkzeuge in Emmerich, contact our experts for precise application support and reliable fulfilment Technical data Article number: M323.E81 GTIN: 4061905068492 Label: Prüfstift, einzeln, 14,81 mm Länge 50 mm Facts Nominal diameter: 14.81 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Weight: 0.1 kg Design / Special features Material: special steel Workshop version (Werkstatt‑Ausführung) Supplied individually Suitable for end‑measurement and fixture reference FAQ What is the dimensional tolerance of this gauge pin? The M323.E81 gauge pin is manufactured to a tolerance of ±0.002 mm, suitable for precision reference and inspection tasks. Which material is used for the pin and why? The pin is made from special steel to combine surface hardness with fatigue resistance, ensuring stable diameters under repeated use. Is the 50 mm length suitable for fixture checks? Yes, the 50 mm length provides sufficient engagement for stable seating in fixtures while remaining easy to handle during set‑up. Can the pin be used as a reference for concentricity checks? The pin’s tight dimensional tolerance and cylindrical geometry make it appropriate as a reference for concentricity and bore alignment evaluations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.82mm Gauge Pin 50mm Length Workshop Finish - Metav IndustryLine
Benefit from high‑precision inspection with a compact, workshop‑grade gauge pin: the ±0.002 mm tolerance, special steel construction and 50 mm length combine to deliver reproducible end‑dimension checks and robust handling. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.E82 — Single gauge pin, Ø 14.82 mm, 50 mm length (Metav IndustryLine) A gauge pin M323.E82 designed for precise end‑dimension verification and reference checks in workshop metrology and quality control. High precision ±0.002 mm tolerance Solid special‑steel construction Compact 50 mm length for tight spaces Supplied in protective transport case Guarantees repeatable end‑dimension checks The gauge pin serves as a compact reference for end‑dimension measurement, providing a verified diameter of 14.82 mm with a tight ±0.002 mm tolerance. Such accuracy reduces measurement uncertainty and supports consistent pass/fail decisions on the shop floor. Classified in the micro range (10–100 mm), this format is particularly suited to finely detailed assemblies and small fixtures where reproducible reference sizes matter. Built for everyday workshop use Constructed from special steel and offered in a dedicated workshop version, the pin is engineered for repeated handling and integration into routine inspection benches. The 50 mm length and 0.1 kg mass make it easy to position in confined spaces without compromising stability. Delivery in a protective transport case preserves the calibrated geometry during storage and transfer; the case is intended for secure transport rather than permanent storage. Integrates into quality workflows with minimal friction This precision inspection pin simplifies checking processes by serving as an immediate go‑to reference for end‑measurements and small assembly checks. The compact design allows inclusion in existing inspection kits or use alongside handheld gauges and fixtures. Backed by Metav IndustryLine’s workshop range, the element supports reliable supply and traceable quality that helps maintain production flow and reduce rework. For precision reference needs, contact Metav Werkzeuge to discuss availability of the Metav IndustryLine gauge pin M323.E82 and to confirm delivery from our Emmerich centre: info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: M323.E82 GTIN: 4061905069338 Manufacturer: Metav IndustryLine Facts Diameter: 14.82 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.1 kg Special features Material: Special steel Version: Workshop version Application: End‑dimension checks / reference measurement Supplied in transport case for secure transport FAQ What tolerance does the gauge pin offer? The gauge pin M323.E82 is manufactured to a tolerance of ±0.002 mm, suitable for high‑precision reference checks. What material is the pin made from? The pin is made from special steel, supplied in the workshop version to withstand regular handling. Is the pin suitable for confined fixtures? Yes, the compact 50 mm length and precise 14.82 mm diameter make the pin appropriate for tight spaces and small assemblies. How is the pin delivered? The pin is supplied in a protective transport case to preserve geometry during transport and handling. Which inspection tasks is this pin intended for? Designed for end‑dimension verification and reference checks, the pin supports quick shop‑floor inspections and fixture validation. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.83mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of high measuring fidelity and robust workshop construction: the precision of ±0.002 mm combined with a special steel body ensures reliable fit checks and repeatable end‑measurements. Order the test pin directly via Metav Werkzeuge or consult our specialists for application advice and supply details. M323.E83 Test pin (Ø 14.83 mm, 50 mm length) – Metav IndustryLine A single test pin, Ø 14.83 mm and 50 mm long, designed for precise end‑measurements and fit verification in workshop metrology. Workshop-grade construction for daily use Diameter 14.83 mm with ±0.002 mm accuracy 50 mm length for reliable end measurements Made from special steel for dimensional stability Consistent precision for quality control The gauge pin delivers a measured accuracy of ±0.002 mm, making it suitable where tight tolerances are required. As a component of the micro-range (10–100 mm) measuring class, it combines short overhang with high stiffness to reduce bending and measurement variability. This level of repeatability supports efficient quality control processes, lowering the risk of rework and ensuring components meet assembly specifications with confidence. Durable workshop design that keeps production moving Built as a workshop‑grade test pin from special steel, the item resists deformation during routine handling and repeated insertion checks. The 50 mm length provides sufficient engagement for end‑measurements while remaining compact for handheld use or fixture mounting. The robust material choice and simplified geometry reduce maintenance needs and help maintain dimensional stability across frequent inspection cycles. Practical compatibility and straightforward application Delivered as a single test pin, the M323.E83 integrates easily into existing inspection routines and gauge sets for go/no‑go and clearance checks. Its nominal 14.83 mm diameter fits into precision holes and fixtures for clearance verification and assembly trials. The compact weight and form factor support fast handling in busy workshops, helping to streamline inspection steps without introducing unnecessary complexity. Contact Metav Werkzeuge for tailored technical advice or a supply proposal for the Metav IndustryLine test pin M323.E83 — local stock in Emmerich enables dependable delivery to the workshop. Technical data Article number: M323.E83 GTIN: 4061905069345 Brand: Metav IndustryLine Type: Test pin, single Weight: 0.1 kg Material: Special steel Length: 50 mm Diameter: 14.83 mm Accuracy: ±0.002 mm Facts Length: 50 mm Diameter: 14.83 mm Accuracy: ±0.002 mm Weight: 0.1 kg ECLASS: 21170231 Special features Workshop version Micro-range classification (10–100 mm) Single item delivery Suitable for end‑measurements and fit checks FAQ What tolerance can be expected from this test pin? The test pin M323.E83 is specified with an accuracy of ±0.002 mm, making it suitable for tight tolerance checks in workshop environments. Is the material corrosion‑resistant? The M323.E83 is manufactured from special steel; details on specific surface treatments are not included in the product data and can be requested from Metav Werkzeuge if required. Can this pin be used for plug‑gauge verification? Yes, the pin’s 14.83 mm diameter and 50 mm length make it suitable for plug and fit verification as part of a gauge set or inspection routine. How is the test pin supplied? The product is supplied as a single test pin (M323.E83) ready for immediate integration into inspection workflows. Which applications benefit most from this test pin? Typical uses include end‑measurements, clearance checks and assembly trials in mechanical workshops, toolrooms and small‑batch production where micro‑range accuracy is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.84mm Gauge Pin 50mm Length Workshop Version, Special Steel ±0.002mm - Metav IndustryLine
Take advantage of precise end‑dimension control and robust workshop design to maintain production quality with minimal rework; the combination of ±0.002 mm tolerance, special steel construction and compact form factor supports consistent inspection routines. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for application advice. M323.E84 gauge pin (Ø 14.84 mm, 50 mm length) — Metav IndustryLine The M323.E84 gauge pin is a solitary precision reference pin designed for end‑dimension checks and fixture set‑up in workshop and production metrology. High precision ±0.002 mm accuracy Hardened special-steel construction 50 mm length, Ø 14.84 mm for end-dimension checks Precision that reduces rework and speeds inspection The core benefit of a tight tolerance is predictable decision‑making during quality control. With a declared ±0.002 mm variation, this precision pin serves as a reliable reference for gauging small‑bore fits and verifying component end dimensions; repeatable results reduce the need for secondary inspections and lower scrap rates. The compact diameter and controlled form make it suitable for batch checks where quick, reproducible readings are essential, contributing directly to process efficiency and cost containment. Robust workshop design for everyday use Built for everyday use in production environments, the pin’s special steel composition provides dimensional stability under regular handling. The workshop design balances durability with handling convenience: the 50 mm length and compact mass ensure easy placement in fixtures and pin blocks while the material choice minimises wear over repeated contact cycles. This robustness supports consistent measurement points across production shifts and reduces the risk of unexpected downtime due to worn reference tools. Traceable reference that fits quality workflows Traceability and inventory control are simplified thanks to the clear article identifiers. The item integrates readily into standard inspection routines and pin sets, providing a fixed datum for pass/fail decisions. Markings such as the SKU and GTIN enable straightforward cataloguing within a laboratory or workshop management system, aiding batch documentation and audit trails. Lightweight and compact, the pin can be combined with holding fixtures or used as a stand‑alone checking tool where end‑dimension conformity is a priority. Contact Metav Werkzeuge for technical matching or order the M323.E84 gauge pin through our Emmerich specialists for immediate integration into inspection routines. Technical data SKU: M323.E84 GTIN: 4061905069352 Label: Prüfstift, einzeln, 14,84 mm Länge 50 mm Facts Diameter (mm): 14.84 Length (mm): 50 Weight (kg): 0.1 Accuracy: ±0.002 mm Special features Material: Special steel Workshop design (Werkstatt‑Ausführung) Category: Gauge pin FAQ What applications is this gauge pin suited for? The M323.E84 gauge pin is intended for end‑dimension checks, fixture set‑up and reference measurements in workshop and production metrology. Is the pin compatible with standard pin blocks and fixtures? Yes, the diameter and length make it compatible with common pin blocks and holding fixtures used for end‑dimension verification. How is traceability handled for this product? The gauge pin is supplied with a clear SKU and GTIN for inventory and quality documentation; these identifiers support integration into inspection records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
14.85mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of precision, robust special steel construction and compact length for reliable end‑dimension checks in workshop and production settings. Order the item directly via Metav Werkzeuge or consult our specialists for application advice. Test pin (single) — 14.85 mm diameter, 50 mm length — Metav IndustryLine A Test pin (single) designed for end‑dimension inspection and go/no‑go checks in workshop and production environments. Workshop‑grade construction Nominal diameter 14.85 mm Overall length 50 mm Measuring accuracy ±0.002 mm Consistent precision for end‑dimension inspection The test pin is manufactured for repeatable end‑dimension control, with a nominal diameter of 14.85 mm and an achieved measuring accuracy of ±0.002 mm. Such fine tolerances support process stability during routine checks and incoming inspection, reducing the risk of rework and ensuring components meet specification. The tolerance band indicated reflects the pin's capability to serve as a reliable master or reference for go/no‑go gauging tasks in mechanical workshops and light production. Durable build tailored to workshop demands Constructed from special steel, the component delivers a durable service life even under frequent handling. The overall length of 50 mm keeps the profile compact while providing sufficient engagement for secure seating in fixtures and gauge holders. The tool's workshop version designation signals practical finishing and dimensional robustness suited to everyday use on the shop floor, balancing longevity with straightforward maintenance. Easy integration into fixtures and inspection routines Designed as a single, standalone gauge element, the pin fits into a wide range of dedicated fixtures and testing apparatus. The compact geometry minimises the need for fixture redesign and facilitates quick verification steps during production runs. With a lightweight construction of approximately 0.1 kg, handling is user‑friendly while still providing the rigidity required for precise measurement transfers. The pin supports efficient quality workflows by shortening setup times for repetitive dimensional checks. Quality assurance and distributor reliability Sourcing through Metav provides transparent supply and a clear quality filter for European operations: dependable stock handling from Emmerich and a broad product portfolio tailored to industry needs. The manufacturer and distributor network ensures traceability and consistent availability for routine replacements or expansion of gauge sets, which helps maintain uninterrupted production and quality control cycles. Contact Metav Werkzeuge today for expert advice on integrating this test pin into existing gauges and for assistance sourcing matching inspection accessories from our Emmerich warehouse. Technical data Article number: M323.E85 GTIN: 4061905069369 Manufacturer: Metav IndustryLine Material: Special steel Nominal diameter: 14.85 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.1 kg Version: Workshop‑grade Facts Diameter: 14.85 mm Length: 50 mm Tolerance/Accuracy: ±0.002 mm Weight: 0.1 kg SKU: M323.E85 Special features Single test pin for end‑dimension checks Compact design for fixture compatibility Workshop execution for daily use Article group: Measuring pins FAQ What is the nominal diameter of the test pin? The test pin has a nominal diameter of 14.85 mm, specified for precise end‑dimension inspection. Is the pin suitable for everyday workshop use? Yes. The workshop‑grade execution and special steel construction make the pin appropriate for regular handling and routine gauging tasks. What accuracy can be expected from this measuring element? The measuring accuracy is ±0.002 mm, allowing its use as a reference for fine tolerancing and go/no‑go checks in production control. Which article number and SKU identify this product? This item is listed under article number M323.E85 with SKU M323.E85 and GTIN 4061905069369. Can this pin be used within existing fixtures and gauges? The pin’s compact 50 mm length and standardised diameter enable straightforward integration into many fixtures and testing arrangements without extensive modification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com