Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
18.72mm Test Pin 50mm Length Workshop Finish - Metav IndustryLine
Take advantage of the combination of workshop‑hardened construction, ±0.002 mm tolerance and compact dimensions for reliable end‑measurement checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.I72 — Precision gauge pin, 18.72 mm Ø, 50 mm length (Metav IndustryLine) A gauge pin M323.I72 engineered for accurate end‑measure verification and repeatable inspection tasks in workshop and quality‑control environments. Workshop version, robust construction Diameter 18.72 mm for end‑measure checks Tolerance ±0.002 mm for high repeatability Protective transport case included Accuracy that removes doubt from inspection The central technical advantage is the ±0.002 mm tolerance, which positions this gauge pin in the high‑precision segment for routine workshop inspections. Such a narrow deviation ensures repeatable end‑of‑shaft measurements and dependable reference checks during set‑up or final inspection. The specified accuracy minimises rework and supports consistent quality decisions in production and maintenance processes. Built for the workshop — durable and dependable Made from special steel and released as a workshop version, the pin withstands daily handling and moderate impacts typical in machine shops. The material choice balances hardness with toughness to preserve the measuring surface while resisting wear. Robust construction reduces the need for frequent replacement, ensuring stable measurement results over the part’s service life and saving time on recalibration cycles. Compact form factor for tight fixtures and assemblies With a diameter of 18.72 mm and a length of 50 mm, this precision pin suits confined measuring points and end‑dimension checks where access is limited. Classified within the micro range for calipers and pins (measurement ranges from 10–100 mm), the design combines adequate reach with low bending risk, enabling controlled, repeatable contact even in small jigs and fixtures. Practical handling and traceable delivery Supplied as a single, individually identified gauge pin, the item arrives ready for immediate use in inspection routines. Delivery includes a protective transport case to prevent surface damage during storage and transit, aiding traceability and preserving the calibrated surface finish. The compact mass and neat form factor make handling straightforward on the shop floor and simplify tool storage between measurement cycles. Contact Metav Werkzeuge for tailored advice on integrating the M323.I72 into inspection routines or to arrange immediate supply from our Emmerich stock Technical Data SKU: M323.I72 GTIN: 4061905072420 Manufacturer: Metav IndustryLine Weight: 0.15 kg Material: Special steel Length: 50 mm Diameter: 18.72 mm Tolerance / Accuracy: ±0.002 mm Label: Gauge pin, single, 18.72 mm diameter, 50 mm length Story trigger: end dimensions Facts Measurement range max: 18.72 mm Measurement range min: 18.72 mm Measurement resolution hundredths: 2 Measurement range tenths: 7 Special features Workshop design Delivered as single pin Protective transport case for transport and storage Ideal for end‑measure verification and inspection tasks FAQ What is the intended use of this gauge pin? This gauge pin is intended for end‑measurement verification and routine inspection tasks; the M323.I72 from Metav IndustryLine serves as a stable reference for end‑dimension checks. How precise is the measurement capability? The M323.I72 offers a tolerance of ±0.002 mm, providing high repeatability for shop‑floor inspection and set‑up verification. Which materials is the pin suited to measure or check? The pin is a dimensional reference rather than a cutting tool; it is suitable for gauging components made of metals and assemblies where an 18.72 mm reference diameter is required. Is the pin delivered ready for use and protected in transit? The gauge pin is supplied individually and comes in a protective transport case to preserve the measuring surface and simplify storage. Can the M323.I72 be used in tight fixtures and jigs? Yes; the compact 50 mm length and precise 18.72 mm diameter make it well suited to confined fixtures and end‑face measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.73mm Test Pin Single 50mm Length Workshop Version - Metav IndustryLine
Benefit from the combination of ±0.002 mm tolerance, Special steel construction and a compact 50 mm length for dependable end‑dimension control; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application support. Gauge pin M323.I73 — precision test pin, 18.73 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.I73 is a precision measurement pin designed for end‑dimension checks, fixture alignment and reference positioning in workshop and inspection environments. High precision 18.73 mm diameter ±0.002 mm Robust special steel workshop design Compact 50 mm length for easy handling Delivered in protective transport case Consistent dimensional control that reduces rework A small investment in a reliable reference element pays back through fewer rejected parts and shorter inspection cycles. With a declared tolerance of ±0.002 mm, this test pin provides repeatable end‑dimension checks that support statistical quality control and batch validation. The tight tolerance is particularly valuable in production lines where small deviations cause downstream assembly issues, enabling operators to identify out‑of‑spec components quickly and prevent costly rework. Durable workshop construction for everyday use Engineered as a workshop execution item, the pin combines a compact form with robust finishing for repeated use under workshop conditions. The Special steel material resists wear and preserves the functional diameter across many cycles, while the 50 mm shaft provides a balance between reach and rigidity. Its manageable mass makes handling and fixture placement straightforward, which contributes to consistent measurement results even during frequent changeovers. Easy integration with fixtures and alignment tools As a single precision pin, the component is suitable as a datum, alignment peg or go/no‑go reference in jigs and setups. The nominal 18.73 mm diameter fits into custom bushings or hardened locating holes and reduces setup time by delivering an immediately usable reference surface. Where fixture repeatability matters, the pin supports faster machine starts and more predictable assembly outcomes, translating into measurable efficiency gains on the shop floor. Protected transport and clear identification Delivered in a protective case, the pin arrives ready for safe storage and transport between workstations or the inspection bench. Each item is labelled for traceability, facilitating inventory control and preventing mix‑ups during maintenance tasks. The compact packaging also simplifies logistical handling when multiple precision elements are required across different production areas. For a reliable precision reference, contact Metav Werkzeuge in Emmerich to request the Metav IndustryLine gauge pin M323.I73 or speak with our consultants at +49 2822 7131930 / info@metav-werkzeuge.com for application advice and supply options. Technical data Article number: M323.I73 GTIN: 4061905072437 Label: Gauge pin, single, 18.73 mm, length 50 mm Facts Diameter: 18.73 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Design: Workshop execution Delivery: protective transport case Intended use: end‑dimension checks / fixture alignment FAQ What is the declared tolerance of this gauge pin? The declared tolerance for the gauge pin M323.I73 is ±0.002 mm, making it suitable for demanding dimensional checks. Is the pin suitable for fixture alignment in production jigs? Yes, the Metav IndustryLine gauge pin M323.I73 is designed for use as a datum or alignment element in fixtures and jigs. What material is used for the pin and how does that affect durability? The pin is made from Special steel, chosen for wear resistance and long service life under regular workshop use. How is the pin delivered and stored to avoid damage? The gauge pin is supplied in a protective transport case to prevent damage in transit and to simplify safe storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.74mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
The workshop-grade gauge pin combines ±0.002 mm repeatability with a 18.74 mm nominal diameter and a 50 mm length to ensure consistent end‑measurement and fit checks in serial or spot inspections; order directly via Metav Werkzeuge or consult the team for application advice. M323.I74 gauge pin by Metav IndustryLine — 18.74 mm diameter, 50 mm length The M323.I74 is a single workshop-grade gauge pin designed for precise end measurements and fit verification in production and inspection routines. Workshop-grade construction Diameter precisely 18.74 mm Length 50 mm for reach and stability Tolerance ±0.002 mm for repeatable checks Consistent accuracy for routine inspection and setup Engineered for stable, repeatable measurements in workshop environments, this gauge pin offers a tolerance of ±0.002 mm, which translates into reliable pass/fail decisions during assembly and setting operations. The tight tolerance reduces rework by providing a verifiable reference for holes and bores, while the compact 50 mm shank length balances reach and rigidity for straightforward handling. The design supports rapid comparative checks and is suitable for inline verification where reproducibility is critical. Robust material and workshop suitability for everyday use Made from special steel, the test pin resists wear and keeps gaging surfaces stable across repeated use, extending service life and reducing the frequency of replacements. The workshop execution prioritises durability and practical handling: a firm, machined finish ensures seating stability in fixtures and minimises micro‑movement during checking. For shops that require a durable reference part for set‑ups or maintenance, the construction provides a good compromise between toughness and dimensional stability. Efficient integration into inspection processes As a single, calibrated reference element with a nominal diameter of 18.74 mm and 50 mm length, the pin is straightforward to incorporate into existing jigs, test benches or handheld comparators. The compact form factor simplifies storage and transport within a production cell, while the precise diameter supports tight tolerance fits and go/no‑go assessments. Where traceable benchmark parts are required for frequent checks, this gauge pin serves as a compact, repeatable solution that complements broader metrology equipment. For reliable workshop precision and application support, contact Metav Werkzeuge in Emmerich to discuss the M323.I74 gauge pin and complementary measurement solutions via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.I74 GTIN: 4061905449420 Weight: 0.15 kg Facts Diameter: 18.74 mm Length: 50 mm Tolerance: ±0.002 mm Special features Material: Special steel Workshop execution Single test pin FAQ What is the nominal diameter and length of the pin? The pin has a nominal diameter of 18.74 mm and a length of 50 mm, designed for stable end‑measurement checks. How precise is the M323.I74 gauge pin? The M323.I74 gauge pin is specified with a tolerance of ±0.002 mm, suitable for repeatable workshop inspection tasks. Is the material suitable for heavy‑duty use? Constructed from special steel, the pin is intended for robust workshop use and maintains dimensional stability under frequent handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.75mm Gauge Pin Single 50mm Length Workshop Finish - Metav IndustryLine
Benefit from the combination of high repeatability, robust special‑steel construction and a compact 50 mm length for reliable end‑dimension checks; order the Test Pin directly via Metav Werkzeuge or consult our advisors for application advice. Test Pin M323.I75 — Precision test pin, 18.75 mm Ø, 50 mm length (Metav IndustryLine) The Test Pin 18.75 mm is a workshop‑grade precision pin for end‑dimension verification and fixture alignment in production and assembly environments. Workshop‑grade special steel construction Diameter 18.75 mm for precise fit checks Length 50 mm suited to confined assemblies Tolerance ±0.002 mm for high reproducibility Repeatable checks where tolerance matters Engineered for consistent verification, the Test Pin M323.I75 combines a nominal diameter of 18.75 mm with a declared tolerance of ±0.002 mm, enabling fast go/no‑go or seating checks during incoming inspection and assembly. The fine tolerance reduces ambiguous fits and helps to avoid rework cycles, delivering measurable time savings on repetitive tasks. By converting a visual or manual trial into a quantified reference, the pin supports streamlined quality control and faster decision‑making on the shop floor. Robust workshop construction for everyday handling Constructed from special steel in a workshop‑grade design, the pin offers mechanical resistance against knocks and frequent handling while maintaining dimensional integrity. The 50 mm shank length is optimised for confined spaces and typical fixture depths, ensuring the pin seats fully without excessive protrusion. The compact mass and balanced geometry keep handling comfortable and reduce the risk of bending during routine use, which in turn preserves calibration intervals and lowers lifecycle costs for tooling. Practical integration into inspection and assembly workflows As a single test pin for end‑dimension checks, it functions well as a reference plug for alignment, seat testing and verification of bore fits. The moderate weight and compact form make storage and rapid selection straightforward in busy workstations. Where multiple diameters are used, the consistent manufacture process across the Metav IndustryLine range ensures comparable tactile feedback and interchangeability between reference pins. The clearly legible SKU and GTIN facilitate inventory control and traceability in procurement and quality records. Choose the Metav IndustryLine Test Pin for reliable end‑dimension verification — contact Metav Werkzeuge for application guidance or to request compatibility information at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.I75 GTIN: 4061905449437 Label: Prüfstift, einzeln, 18,75 mm Länge 50 mm Facts Diameter: 18.75 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Workshop version Material: Special steel Single test pin Storytrigger: end‑dimension checks FAQ What tolerance can be expected from this test pin? The Test Pin M323.I75 is manufactured with a declared tolerance of ±0.002 mm, suitable for high‑repeatability seating and fit checks. Is the pin suitable for fixture alignment and bore seating checks? Yes — the 18.75 mm diameter and 50 mm length make it well suited for fixture alignment, bore seating and end‑dimension verification in assembly processes. What material is used for the pin and how does that affect durability? The pin is made from special steel in a workshop‑grade finish, offering resistance to everyday handling and maintaining dimensional stability under normal use. Can this pin be used alongside other Metav IndustryLine reference pins? Yes — the Metav IndustryLine family is produced to consistent manufacturing standards so that pins of different diameters provide comparable handling and interchangeability. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.76mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Reliable workshop-grade precision thanks to ±0.002 mm tolerance and special steel construction, combined with a compact Ø 18.76 mm / 50 mm length design and a protective transport case for safe handling — order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin Ø 18.76 mm — 50 mm length (Metav IndustryLine) The gauge pin Ø 18.76 mm, 50 mm is a workshop-grade inspection pin for end-dimension verification and fixture setting in production and maintenance environments. Workshop-grade construction Diameter Ø 18.76 mm, length 50 mm High dimensional accuracy ±0.002 mm Supplied in protective transport case Consistent metrology for fast in-process checks This compact gauge pin delivers repeatable results for routine end‑dimension and fit checks. With a declared dimensional tolerance of ±0.002 mm, the pin suits tasks where small deviations matter and where fast decisions on acceptance or rework shorten cycle times. The combination of a precise diameter and a short, rigid shank reduces deflection during insertion, which supports quicker verification on assembly benches or inspection jigs. This reliability translates into fewer interruptions and a steadier production flow. Durable construction that copes with workshop demands Manufactured from special steel, the pin offers enhanced wear resistance and long service life under regular workshop use. The workshop-grade finish tolerates handling and routine contact with fixtures, minimising surface damage that could affect measurement accuracy. Supplied in a protective transport case, the component remains protected during storage and transit, reducing the risk of accidental knocks and preserving the measurement surface for longer intervals between maintenance. Practical integration and application guidance The product is delivered as a single inspection pin suitable for use in plug‑gauge checks, fixture alignment and end‑dimension control on machining or assembly tasks. Its compact form factor and modest mass make it easy to handle at the bench or in a gauge block set without specialised tooling. For specific application setups or compatibility questions, Metav IndustryLine offers technical guidance to ensure correct selection and handling for intended measurement tasks. For precise end-dimension verification with the Metav IndustryLine gauge pin, contact Metav Werkzeuge for specialist advice and reliable supply from Emmerich. Technical data SKU: M323.I76 GTIN: 4061905449444 Material: Special steel Diameter: 18.76 mm Length: 50 mm Dimensional tolerance: ±0.002 mm Weight: 0.15 kg Version: Workshop-grade Packaging: Protective transport case Facts Diameter (numeric): 18.76 mm Length (numeric): 50 mm Tolerance (numeric): ±0.002 mm Weight (numeric): 0.15 kg Special features Single gauge pin delivery Robust surface finish for workshop use Protective transport case for safe handling Suitable for end-dimension verification and fixture setting FAQ What is the dimensional tolerance of this gauge pin? The Metav IndustryLine gauge pin has a specified dimensional tolerance of ±0.002 mm. Which material is used for the pin? The gauge pin (SKU M323.I76) is made from special steel, providing wear resistance suited to workshop conditions. Is a calibration certificate included with the product? The product data does not specify a calibration certificate; no ISO 17025 calibration is indicated for this item. How is the pin supplied and protected? The single pin is supplied in a protective transport case to preserve the measurement surface during storage and transit. What applications is this gauge pin best suited for? Designed for end-dimension checks, plug‑gauge verification and fixture alignment in production, maintenance and inspection workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.77mm Gauge Pin, Workshop Version, 50mm Length - Metav IndustryLine
Take advantage of precise workshop measurement with a robust single test pin that combines Ø 18.77 mm nominal diameter, tight tolerance ±0.002 mm and a solid 50 mm working length for reproducible end‑dimension checks; order directly via Metav Werkzeuge or consult Metav specialists for integration advice. M323.I77 test pin (gauge pin) – Ø 18.77 mm, 50 mm length by Metav IndustryLine A M323.I77 test pin designed for end‑dimension verification, fixture set‑up and go/no‑go checks in workshop and production inspection environments. Workshop‑grade single test pin Ø 18.77 mm nominal diameter ±0.002 mm tolerance for repeatable checks Solid 50 mm working length Delivered in a transport case Reliable inspection for everyday workshop use The M323.I77 is engineered as a workshop‑grade test pin that delivers consistent dimensional references in manual and semi‑automated inspection routines. With a nominal diameter of 18.77 mm and a declared tolerance of ±0.002 mm, the pin provides a verifiable reference for end‑dimension checks and fixture alignment. The compact 50 mm length gives sufficient engagement for stable seating while remaining easy to handle during repetitive checks. The combination of robust geometry and a precise manufacturing tolerance reduces rework and inspection time, supporting a steady production flow. How precision and material translate into dependable results Manufactured from special steel, the pin balances wear resistance with machinability, ensuring dimensional stability under typical workshop conditions. The stated tolerance corresponds to a high level of repeatability for a single plug‑type gauge, which makes the component suitable for pass/fail inspection, setting gauges and reference measurements. For users accustomed to micrometrology, this item fits between quick go/no‑go checks and more elaborate gauge procedures, offering a pragmatic compromise of accuracy and durability for everyday measurement tasks. Practical integration, handling and storage benefits The solid construction and standardised diameter facilitate straightforward use in fixture set‑ups, dedicated plug jigs or comparative checks against master gauges. The 50 mm length provides a comfortable gripping area while ensuring consistent seating in bores or against end faces. Delivery in a transport case protects the gauge during storage and transit, helping to maintain the rated tolerance and surface condition. Lightweight handling and the compact footprint support rapid changeovers on the inspection bench without adding significant tool inventory complexity. Recommended applications and workflow advantages This gauge pin is particularly suited to end‑dimension verification, assembly checks and quick reference measurements in metalworking and component assembly. Its workshop orientation makes it a practical tool for maintenance departments, small series production and quality control stations where reliable, repeatable checks are required without the overhead of specialised laboratory equipment. Where a traceable master or batch control is needed, the pin serves as a stable, low‑effort reference for everyday quality routines. Contact Metav Werkzeuge in Emmerich for tailored advice and prompt delivery of the Metav IndustryLine M323.I77 test pin, or ask our consultants for assistance integrating the pin into existing inspection workflows Technical data Article number: M323.I77 GTIN: 4061905449451 Label: Prüfstift, einzeln, 18,77 mm Länge 50 mm Manufacturer: Metav IndustryLine Category: Messstifte Facts Diameter: 18.77 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version Delivered in a plastic or wooden transport case Single test pin for end‑dimension verification FAQ What applications is this test pin suited for? This M323.I77 test pin by Metav IndustryLine is intended for end‑dimension verification, fixture set‑up and pass/fail checks in workshop and production inspection contexts. How precise is the gauge and what does the tolerance mean? The pin carries a tolerance of ±0.002 mm, which indicates the maximum deviation allowed from the nominal Ø 18.77 mm; this level of precision supports repeatable reference measurements in routine quality checks. What material is used and how does it affect wear? The component is made from special steel, chosen to offer a balance of wear resistance and dimensional stability for regular workshop usage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.79mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of exact diameter control, robust special steel construction and a finely matched length for reliable positioning and repeatable inspection cycles. Order the gauge pin directly via Metav Werkzeuge or contact the consultants for application advice. Gauge pin M323.I79 — 18.79 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.I79 is a single precision test pin made for workshop metrology tasks, offering a stable reference for end‑measurements, alignment and fit checks in small to medium‑sized assemblies. Precision diameter 18.79 mm fit Tight tolerance ±0.002 mm Special steel construction 50 mm length for workshop use Repeatable fits through controlled diameter and tolerance A controlled diameter of 18.79 mm combined with a stated tolerance of ±0.002 mm ensures highly repeatable fits when checking hole diameters, locating dowel seats or verifying mating parts. The close tolerance reduces variability in assembly checks and minimises the need for rework. For routine inspection tasks, this level of accuracy provides confidence that measured clearances and interference fits reflect the component reality rather than measurement scatter. Robust alloy for everyday workshop handling Manufactured from special steel, the pin is designed to tolerate frequent use in workshop environments without rapid wear. The choice of material provides an advantageous balance between surface hardness and toughness, which benefits longevity when the pin is used in fixture setups, gauging rigs or manual verification operations. At an overall length of 50 mm and a mass of 0.15 kg, the component remains easy to handle while delivering the rigidity required for consistent contact in inspection sequences. Integrates smoothly with standard inspection procedures As a precision test pin, this component slots into existing metrology workflows — from simple go/no‑go checks to documented inspection steps in quality control. The form factor supports secure seating in gauge blocks, holders or bespoke fixtures used for end‑measurement and alignment. Because the dimensioning is exact, the pin serves as a reliable reference for process stability and for validating tooling that relies on tightly defined plug diameters. Practical care to preserve accuracy To maintain the specified ±0.002 mm performance, routine care is recommended: keep the contact surfaces clean, protect the shaft from knocks, and store the pin in a dry environment to prevent surface corrosion. Occasional inspection for wear and a controlled handling procedure will extend service life and preserve measurement integrity. Where traceable documentation is required, consult Metav Werkzeuge about available calibration options and traceability practices. For workshop precision and dependable inspection results, request the Metav IndustryLine gauge pin M323.I79 from Metav Werkzeuge — expert advice and reliable delivery from Emmerich are available at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M323.I79 GTIN: 4061905449864 Description: Gauge pin, single, 18.79 mm diameter, 50 mm length Facts Diameter: 18.79 mm Length: 50 mm Accuracy / tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Category: Gauge pins (Messstifte) FAQ What is the indicated tolerance and what does it mean in practice? The stated tolerance of ±0.002 mm means the diameter of the gauge pin is held within two micrometres of the nominal 18.79 mm, providing a tight reference suitable for precision fit and inspection tasks with low variability. Can the pin be used for mounting and locating components in fixtures? Yes. The design and special steel construction make the pin suitable for locating, alignment and fixture tasks where a stable, precise plug diameter is required. Is the pin supplied as a single item or as part of a set? This entry describes a single gauge pin; the SKU M323.I79 identifies the individual component supplied on its own for bespoke or replacement use. How should the gauge pin be maintained to preserve accuracy? Keep the shaft clean and dry, avoid impacts and store in protective packaging when not in use; regular visual checks for wear are recommended to ensure ongoing measurement reliability. Which applications are typical for this type of gauge pin? Typical uses include end‑measurement checks, hole gauging, alignment of mating parts and use as a reference in manual or semi‑automatic inspection processes. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.7mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of high repeatability through a ±0.002 mm tolerance, robust special steel construction and practical transport packaging to keep inspection routines efficient; order directly via Metav Werkzeuge or consult our technical advisers for specification support. Gauge pin M323.I70 — 18.7 mm diameter, 50 mm length (Metav IndustryLine) The gauge pin M323.I70 is a workshop‑grade test pin designed for reliable end‑dimension and bore checks in inspection, assembly and fixture set‑up applications. Workshop‑grade execution Diameter 18.7 mm, length 50 mm Tolerance ±0.002 mm Supplied in transport box Precision where fit and repeatability count A compact measuring pin with a declared tolerance of ±0.002 mm delivers measurable gains in quality control: the low variation drastically reduces uncertainty when verifying bore diameters or mating parts. Where interchangeability and batch consistency are required, this level of repeatability shortens inspection time and lowers the risk of rework. The design supports quick reference checks and integration into standard inspection routines, providing a rational, efficiency‑driven improvement to production control. Durable design for workshop conditions Manufactured from special steel, the pin is intended for regular shop‑floor use; the material choice balances hardness with wear resistance to maintain dimensional stability over many cycles. The workshop‑grade execution means edges and surfaces are suited to handling and fixture contact without delicate treatment, which benefits users who require a robust, low‑maintenance measuring element. Where frequent insertion and removal are part of the process, longevity of the measuring surface preserves calibration intervals and reduces total cost of ownership. Practical handling and application benefits With a 50 mm length and a precise 18.7 mm diameter, the test pin is sized for end‑dimension checks and plug‑type verification tasks in assembly or inspection fixtures. Delivery in a transport box protects the gauge during storage and transit, ensuring the measuring face remains blemish‑free until first use. Clear identification via the SKU and GTIN simplifies inventory management and traceability in a centralised tool pool, helping to keep inspection workstreams orderly and efficient. Discuss application needs with Metav Werkzeuge and secure the Metav IndustryLine gauge pin for dependable bore and end‑dimension checks — contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com, +49 2822 7131930 Technical data SKU: M323.I70 GTIN: 4061905072406 Manufacturer: Metav IndustryLine Material: special steel Diameter: 18.7 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm Facts Diameter: 18.7 mm Length: 50 mm Weight: 0.15 kg Tolerance: ±0.002 mm GTIN: 4061905072406 Special features Workshop‑grade execution Supplied in transport box for transport protection Suitable for end‑dimension and bore checks Robust measuring surface for regular use FAQ What material is the test pin made from? The test pin M323.I70 is manufactured from special steel, chosen for a balance of hardness and wear resistance suitable for workshop inspection. What tolerance can be expected from this gauge pin? The gauge pin is specified with a tolerance of ±0.002 mm, ensuring high repeatability for dimensional checks. Is the test pin suitable for routine bore inspections on the shop floor? Yes, the workshop‑grade design and protective transport box make the measuring pin well suited to routine bore and end‑dimension inspections in production environments. How is the instrument delivered and protected? Delivery includes a transport box to protect the measuring surfaces during storage and transit; the packaging supports safe handling until the pin is first used. Which product identifiers help with traceability? Traceability is supported by SKU M323.I70 and GTIN 4061905072406, enabling straightforward inventory and procurement control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.82mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of precise, workshop‑ready measurement with a gauge pin that combines tight tolerance and robust construction for reliable end‑measurements; order the item directly via Metav Werkzeuge or consult our specialists for application advice. M323.I82 Gauge Pin – 18.82 mm diameter, 50 mm length (Metav IndustryLine) The M323.I82 gauge pin is a single precision inspection pin intended for end‑measurement, fixture setting and rapid go/no‑go checks in workshop and inspection environments. Precision tolerance ±0.002 mm Exact diameter 18.82 mm 50 mm length, workshop version Supplied in protective case Accuracy that secures measurement certainty This inspection pin delivers a consistent fit for end‑measurement tasks thanks to its declared tolerance of ±0.002 mm, which keeps dimensional variation within tight limits. Such accuracy reduces uncertainty when establishing reference points, so inspection routines and fixture set‑ups run with fewer adjustments and less rework. The specified 18.82 mm diameter is manufactured to an exact nominal size, making the pin suitable for rapid pass/fail checks and repeatable seating in bores, gage blocks or locating features. Emphasis on repeatability and minimal deviation underpins efficient quality control across short production runs and regular workshop checks. Durable construction designed for workshop use Manufactured in special steel, the pin is engineered for dimensional stability under frequent handling typical of a workshop environment. The 50 mm length offers sufficient engagement for many reference and seating applications while remaining compact for quick handling and insertion in fixtures. The product is supplied in a workshop version, signifying practical features for everyday use, and its modest mass (approx. 0.15 kg) supports convenient manual operation without compromising rigidity. The material choice and finish prioritise steady geometry over time, which helps maintain consistent measurement results and lowers the need for premature replacement. Practical integration into inspection workflows As a single gauge pin for end‑measurements, this tool integrates easily into fixture calibration, bore validation and assembly verification workflows. Its exact diameter simplifies the creation of reliable master references and aids rapid alignment of components during assembly or testing. Supplied in a protective case, the pin is protected during transport and storage, preserving the calibrated condition and surface quality required for accurate measurements. For workshop teams aiming to streamline inspection steps, the pin acts as a compact, low‑effort reference that complements gauges and measuring instruments in a coherent quality routine. Contact Metav Werkzeuge to confirm suitability of the M323.I82 for specific applications and to arrange prompt supply from Emmerich Technical data Article number: M323.I82 SKU: M323.I82 GTIN: 4061905449895 Dimensions & weight Diameter: 18.82 mm Length: 50 mm Weight: 0.15 kg Materials & features Material: Special steel Tolerance: ±0.002 mm Workshop version Supplied in protective case FAQ What is the declared tolerance of this gauge pin? The declared tolerance for the M323.I82 gauge pin is ±0.002 mm, ensuring tight dimensional control for end‑measurement tasks. Is the pin suitable for fixture setting and repeatable alignment? Yes, the gauge pin from Metav IndustryLine is intended for fixture setting, alignment and go/no‑go checks where precise diameter control is required. How is the item supplied and protected for transport? The M323.I82 is supplied in a protective case to safeguard the gauge pin during transport and storage. What material is used for the pin and why does it matter? The pin is made from special steel; this provides stable geometry under handling and contributes to long‑term measurement reliability. Which SKU should be referenced when ordering? Please reference SKU M323.I82 when enquiring or ordering to ensure the correct gauge pin is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.83mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop‑grade gauge pin that delivers consistent end‑dimension checks thanks to its precise Ø 18.83 mm diameter and ±0.002 mm tolerance; the robust special steel construction and 50 mm length ensure stable seating in fixtures and repeatable results—order through Metav Werkzeuge or request specialist advice from Metav consultants. Gauge pin M323.I83 – inspection pin, Ø 18.83 mm, length 50 mm (Metav IndustryLine) A gauge pin M323.I83 designed for precise end‑dimension verification and fixture alignment in workshop and production metrology. Workshop version, robust design Ø 18.83 mm for end‑dimension checks Length 50 mm for fixture alignment Made from special steel Reliable verification for end‑dimension checks The compact inspection pin provides a stable reference for end‑dimension checks and final inspection steps in component manufacturing. With a nominal Ø 18.83 mm and a stated tolerance of ±0.002 mm, the pin offers a repeatable datum for checking seats, bores and mating parts. The clear numeric specification and simple geometry reduce interpretation effort during quality assurance, enabling faster decisions in the measuring loop and fewer reworks. Workshop suitability and handling benefits Specified as a workshop version, the pin combines durability with straightforward handling. The 50 mm effective length suits fixture alignment and short‑reach gauges where rigidity and minimal deflection are essential. Its compact geometry simplifies insertion and extraction from jigs and gauges, so inspection cycles remain efficient even under frequent use. The single‑piece supply supports flexible inventory management for small series and maintenance tasks. Material choice and measurement confidence Manufactured from special steel, the pin maintains dimensional stability under typical workshop conditions and offers a balance of wear resistance and machinability. The declared measurement tolerance ±0.002 mm gives a clear expectation of fit and interchangeability, which simplifies specification sheets for production engineers and inspectors. The precise diameter and high material consistency reduce uncertainty when creating go/no‑go assemblies or when building gauge stacks. Integration into quality workflows As a straightforward inspection element, the pin integrates easily into existing gauge sets and fixture arrays. The simple form factor minimises sources of measurement error and supports rapid tactile verification as well as optical or machine‑assisted checks. Delivered as a single inspection pin with protective transport packaging, it is suitable for in‑line checks, fixture setup, and end‑of‑line acceptance testing where clear pass/fail criteria are required. Contact Metav Werkzeuge for application advice and reliable supply of the Metav IndustryLine gauge pin M323.I83—expert assistance from Emmerich ensures the right fit for production or maintenance tasks Technical data Article number: M323.I83 GTIN: 4061905449901 Material: Special steel Version: Workshop version Delivery: Protective transport case included Facts Diameter: 18.83 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Single piece supply Intended for end‑dimension checks and fixture alignment Robust design for frequent workshop use FAQ What tolerance does the gauge pin offer? The gauge pin M323.I83 is specified with a tolerance of ±0.002 mm, making it suitable for precise end‑dimension verification in workshop and production settings. Which material is used for this inspection pin? This inspection pin is made from special steel, selected for dimensional stability and durability in workshop applications under Metav IndustryLine. What are the dimensions and weight of the pin? Nominal diameter is 18.83 mm with a length of 50 mm; the item weight is approximately 0.15 kg for handling and storage considerations. Is the pin suitable for fixture alignment and gauge stacks? Yes—its 50 mm length and precise diameter make the M323.I83 appropriate for fixture alignment, gauge stacks and end‑mass checks where a stable datum is required. How is the product delivered? The gauge pin is supplied as a single piece and shipped in a protective transport case to secure the item during transit Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.84mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Precision measurement with repeatable fit: 18.84 mm diameter, ±0.002 mm tolerance and robust special steel construction ensure reliable end‑measurement checks. Order the gauge pin directly via Metav Werkzeuge or consult our experts for application advice. Gauge pin M323.I84 — Single gauge pin, Ø 18.84 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.I84 is a workshop-grade precision test pin for end‑measure checks and fitting tasks in mechanical assembly and quality control. Precise diameter 18.84 mm ±0.002 Special steel construction for durability 50 mm length for assembly and gauge blocks Delivered in a protective transport case Consistent fits for repeatable checks This single test pin delivers a consistent datum for go/no‑go checks and alignment tasks. The nominal 18.84 mm diameter with a verified ±0.002 mm deviation provides the level of repeatability demanded in series inspection and setup work, reducing trial adjustments and assembly rejects. Because the pin is manufactured from special steel, surface wear is limited and contact-induced distortion is minimised, which preserves measurement integrity during repeated use. Designed for workshop handling and inspection With a compact 50 mm working length the pin is optimised for confined spaces and fixture checks where a short, rigid gauge element is advantageous. The workshop execution balances stiffness and handling convenience, allowing rapid insertion and tactile confirmation of fit without elaborate fixturing. The design supports efficient process control: fewer interruptions, faster pass/fail decisions and clearer documentation of component conformity. Straightforward integration into QA routines The pin is suited to mechanical assembly, gauge setting and comparative checks within toolrooms and production lines. Traceable identification (SKU M323.I84, GTIN included in technical data) simplifies stock management and inspection records. Supplied in a protective transport case, the gauge reaches the bench ready for immediate use and safe storage between shifts, helping to maintain surface condition and dimensional reliability. Confidence through practical specification Specification-led selection reduces uncertainty in procurement: a compact test pin with a tight tolerance class supports both production monitoring and final inspection. The combination of measured accuracy, robust material and protective delivery results in a practical tool that supports throughput and lowers rework rates. For teams seeking predictable, workshop-ready measurement aids, this pin represents a pragmatic choice. For workshop-ready precision from Metav IndustryLine and supply from Metav Werkzeuge GmbH in Emmerich, request the gauge pin M323.I84 or contact our technical advisors at info@metav-werkzeuge.com or +49 2822 7131930 for application guidance and availability. Technical Data SKU: M323.I84 GTIN: 4061905449970 Weight: 0.15 kg Facts Diameter: 18.84 mm Length: 50 mm Tolerance: ±0.002 mm Special features Material: Special steel Version: Workshop execution Supplied in a protective transport case Category: Gauge pins FAQ What material is the pin made from? The gauge pin is produced from special steel, offering wear resistance and dimensional stability for routine inspection tasks. What tolerance does the pin meet? Tolerance is ±0.002 mm, providing a high level of repeatability suitable for fine inspection and assembly checks with SKU M323.I84. Can this pin be used for fixture alignment? Yes. The short, rigid 50 mm length and precise diameter make the pin suitable for fixture alignment and go/no‑go verification in workshop environments. How is the pin supplied for storage and transport? The pin is supplied in a protective transport case to safeguard the measuring surface during storage and movement. Is the gauge pin appropriate for micro‑component checks? With its compact dimensions and tight tolerance, the pin is well suited to fine mechanical tasks and small assembly verifications. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.85mm Gauge Pin Length 50mm Workshop Version - Metav IndustryLine
Precision‑engineered for repeatable end‑dimension verification, the gauge pin combines special steel construction with a nominal diameter of 18.85 mm, a 50 mm usable length and a manufacturing tolerance of ±0.002 mm for consistent inspection results. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin, single 18.85 mm / 50 mm (Metav IndustryLine) A gauge pin (18.85 mm, 50 mm length) intended for precise end‑measure checks, fixture set‑up and workshop inspection tasks. Workshop version for robust use Diameter 18.85 mm with ±0.002 mm tolerance 50 mm hardened special steel design Supplied individually for targeted checks Reliable dimensional control for end measurements The gauge pin M323.I85 is made for exacting inspection tasks where repeatability matters. With a nominal size of 18.85 mm and a tight tolerance of ±0.002 mm, this test pin delivers consistent reference geometry for go/no‑go checks, alignment of bore gauges and verification of end dimensions. The short, straight geometry reduces bending and ensures stable seating in inspection fixtures, so measurement variance is minimised and process capability improves. Robust material choice and workshop durability Manufactured from special steel and finished for workshop use, the pin is intended to withstand frequent handling and contact with hardened seating surfaces. The choice of material gives high wear resistance and dimensional stability during repeated cycles of insertion and withdrawal. The 50 mm shaft length provides sufficient engagement for typical bench fixtures while remaining easy to handle and position during rapid checks. Practical integration into inspection workflows Designed as an individual reference pin, this test piece is well suited to in‑process control and fixture calibration. The smooth cylindrical form supports reliable seating in bushings or gauging sockets, and the clearly defined nominal size aids quick traceability on inspection lists. Inclusion of the GTIN ensures easy stock management and line item identification in procurement and quality documentation. Benefits for throughput and quality assurance Using a dedicated gauge pin reduces adjustment time and lowers the risk of operator‑induced variance during inspection. The combination of tight tolerance and durable construction helps to avoid unnecessary rework, supporting higher first‑pass yield and a more efficient quality routine. For workshop and small‑batch environments, the compact design also aids storage and fast deployment at the inspection point. Contact Metav Werkzeuge to discuss suitability for specific inspection rigs, request delivery details or reserve stock of the Metav IndustryLine gauge pin for faster, more reliable end‑measure verification from Emmerich. Technical data SKU: M323.I85 GTIN: 4061905070273 Label: Gauge pin, single, 18.85 mm diameter, 50 mm length Facts Nominal diameter: 18.85 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Supplied individually FAQ What applications is this gauge pin intended for? This gauge pin is intended for end‑dimension verification, fixture set‑ups and go/no‑go checks in workshop and inspection environments. What is the declared tolerance and how does it affect measurements? The declared tolerance of ±0.002 mm ensures high repeatability; the tight tolerance reduces uncertainty when the gauge pin is used as a reference in inspection routines. Is the material suitable for frequent use in production? Yes, the gauge pin is made from special steel and finished for workshop use, providing wear resistance suitable for frequent insertion and withdrawal. Can this pin be used in existing gauging fixtures? The 18.85 mm nominal diameter and standard cylindrical form allow compatibility with many existing sockets and gauges; the SKU M323.I85 helps to identify the exact item for fixture adaptation. How is the product identified for procurement and inventory? Identification is supported by the SKU M323.I85 and GTIN 4061905070273 for straightforward ordering and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.86mm Gauge Pin Length 50mm Workshop Version, Special Steel In Plastic Case - Metav IndustryLine
A compact gauge pin in special steel with a nominal diameter of 18.86 mm, 50 mm length and a tolerance of ±0.002 mm provides repeatable end‑dimension checks and reliable fit verification; supplied in a transport case for safe handling. Order the M323.I86 via Metav Werkzeuge or consult their advisers for application support. Gauge pin M323.I86 — single gauge pin, Ø 18.86 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.I86, a single inspection pin for end‑dimension verification and fit testing in workshop metrology. Single gauge pin Ø 18.86 mm, length 50 mm Manufacturer tolerance ±0.002 mm Special-steel for robust wear resistance Supplied in transport case for secure storage Precision where measurement reliability reduces rework The M323.I86 is manufactured to a tight tolerance of ±0.002 mm, making it suitable for verification tasks where small deviations affect assembly quality. The 18.86 mm nominal diameter is produced with consistent roundness and surface finish to ensure reproducible contact points during inspection. This level of control reduces the need for repeated checks and supports quality assurance processes by providing a measurable reference for end‑dimension and bore verification. Durable construction for demanding workshop use Constructed from special steel, the pin is designed to withstand frequent handling and the abrasive conditions of a busy workshop. The 50 mm length provides stable engagement in holes or mating components while minimising deflection during inspection. The item is offered in a workshop version, optimised for routine use, and is supplied in a transport case to protect the gauge during storage and transit. These attributes together extend service life and maintain measurement integrity over many inspection cycles. Small-format gauge for fine mechanical and component checks This product falls within the micro range (up to 100 mm) of inspection tools, making it ideal for fine mechanical tasks and compact components where a short, rigid pin is required. The compact format supports ease of handling and fast set‑up on benches and fixtures commonly found in metalworking and precision engineering shops. As a single gauge pin, it serves as a precise go/reference element for dimensional checks and assembly verification in production and maintenance workflows. Contact Metav Werkzeuge in Emmerich to discuss the M323.I86 and secure the right gauge pin for workshop inspection tasks — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: M323.I86 GTIN: 4061905070280 Manufacturer: Metav IndustryLine Label: Prüfstift, einzeln, 18,86 mm Länge 50 mm Core specifications Diameter: 18.86 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Delivery: Supplied in a transport case Application: End‑dimension and fit checks FAQ What tolerance does this gauge pin offer? The M323.I86 gauge pin is manufactured to a tolerance of ±0.002 mm, providing high repeatability for end‑dimension checks and fit verification. What material is used for the inspection pin? The inspection pin is made from special steel, chosen for wear resistance and stable measuring behaviour under regular workshop use. Is the gauge pin delivered in protective packaging? Yes, the pin is supplied in a transport case to protect the gauge during storage and transit. Which measurement tasks suit this small gauge pin? This compact pin is intended for micro‑range inspection tasks — end‑dimension verification, bore and fit checks on small components typical in precision engineering and metalworking. Does the product include a calibration certificate? The product data does not specify a calibration certificate; the pin is supplied with the stated manufacturing tolerance of ±0.002 mm as the technical specification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.87mm Test Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop robustness, tight ±0.002 mm tolerance and a compact 50 mm length for reliable end‑dimension checks; order the test pin directly via Metav Werkzeuge or ask our consultants for application advice. M323.I87 Test Pin — Single precision test pin, Ø 18.87 mm, 50 mm length (Metav IndustryLine) M323.I87 is a single precision test pin intended as an end‑dimension reference for workshop metrology, compatible with gauge blocks and fixture checks. Workshop execution for everyday metrology Precision tolerance ±0.002 mm Solid special-steel construction Compact 50 mm length for fixture work Precision where it matters: accurate reference for end‑measurements The M323.I87 functions as a dedicated reference pin for end‑dimension verification and small‑batch inspections. With a nominal diameter of Ø 18.87 mm and a declared accuracy of ±0.002 mm, the pin delivers the repeatability required for tight tolerance checks and routine quality control. The tight tolerance is particularly useful when validating assembly fits, seating surfaces or measuring against calibrated master gauges. The compact geometry and consistent diameter reduce alignment error, providing a reliable tactile and dimensional reference in workshop environments. Robust design for daily workshop use and fast set‑up Manufactured from special steel, the pin combines material strength with a finely finished contact surface that resists wear during repeated use. The 50 mm nominal length balances reach and rigidity, making the component easy to handle and position in fixtures or measuring stands while maintaining profile stiffness. At approximately 0.15 kg, the solid construction feels substantial without being unwieldy, aiding stable placement during checks. This pragmatic design reduces set‑up time and contributes to efficient inspection cycles on the shop floor. Confidence through a trusted supply chain and proven service As part of the Metav IndustryLine, this test pin benefits from a vendor focus on accessible precision: well‑maintained stockholding in Emmerich and a broad metrology range for matching accessories. Metav’s established offering and inventory depth help streamline procurement and reduce supply‑chain risk for production or maintenance teams. The combination of pragmatic engineering and vendor reliability delivers a component that supports reproducible measurement outcomes and steady workshop throughput. For workshop-grade measurement needs, request the Metav IndustryLine M323.I87 precision test pin via Metav Werkzeuge — our Emmerich team can advise on compatibility with existing gauges and supply logistics Technical Data Article number: M323.I87 GTIN: 4061905071171 Brand: Metav IndustryLine Weight: 0.15 kg Material: Special steel Facts Diameter: 18.87 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Workshop execution Single test pin Designed for end‑dimension checks Compact design for fixture use FAQ What are the nominal diameter and length of this test pin? The M323.I87 test pin has a nominal diameter of 18.87 mm and a length of 50 mm. What accuracy can be expected from the pin? The declared manufacturing tolerance for the pin is ±0.002 mm. What material is used for this component? The component is made from special steel, chosen for wear resistance and dimensional stability. For which applications is this pin suitable? The pin is intended for end‑dimension reference checks, fixture setup, and use as a gauge reference in workshop metrology. Is calibration information provided with the product data? Calibration is not specified in the supplied product data. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.88mm Test Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
A compact, workshop-grade test artefact that combines 18.88 mm nominal diameter, 50 mm usable length and a fine ±0.002 mm tolerance to support reliable go/no-go checks and reference measurements; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.I88 — 18.88 mm diameter, 50 mm length (Metav IndustryLine) A gauge pin M323.I88 intended for precision bore checks and reference measurement tasks in workshop metrology and inspection. Precision tolerance ±0.002 mm Diameter 18.88 mm exact fit 50 mm ground length for stability Workshop-grade special-steel design Repeatable bore checks with micrometre-level control This test pin delivers a repeatable reference for bore verification, with a specified ±0.002 mm tolerance that defines its inspection suitability. The 18.88 mm nominal diameter is ground to provide a predictable fit in calibrated bores, making the component useful for go/no-go assessments and comparative gauging. Stating the tolerance as a measurable limit clarifies expected performance during setup and quality control activities and supports traceable decision-making in production. Material choice that withstands workshop use Constructed from special steel, the component is designed as a workshop-grade measurement element that resists routine wear while preserving surface integrity under normal handling. The material choice gives structural stiffness and long-term wear resistance, so dimensional stability is maintained across repeated insertions and withdrawals. Where bench tools and fixture checks demand robustness, this version balances durability with the dimensional precision required for inspection tasks. Compact length and clear traceability for fixture work A 50 mm usable length provides a stable engagement depth without excessive overhang, aiding reproducible seating in fixtures and jigs. The short form factor reduces bending effects during manual handling and supports stable reference surfaces for comparative measurement. Identification via M323.I88 and associated product codes ensures straightforward inventory control and process documentation for inspection routines, improving traceability within quality systems. For workshop-grade inspection components from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for specification support and procurement assistance. Technical data SKU: M323.I88 GTIN: 4061905071188 Manufacturer: Metav IndustryLine Numbers / Core technical data Diameter: 18.88 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Eclass: 21170231 Design / Special features Material: Special steel Version: Workshop execution Item: Single gauge pin Story trigger: endmasse FAQ What is the dimensional tolerance of this gauge pin? The gauge pin M323.I88 is specified with a tolerance of ±0.002 mm, which defines its suitability for fine inspection and repeatable fit checks. Is the component suitable for use as a reference in fixture set-up? Yes; the 50 mm length and ground diameter make it suitable as a reference element for fixture alignment and comparative gauging. What material is used for this test pin? The test pin is manufactured from special steel, selected for its stiffness and resistance to wear in workshop environments. Is the part supplied as a single item or as a set? This article is supplied as a single gauge pin, designated under SKU M323.I88 for inventory and traceability. How should the gauge pin be managed within a quality system? Record the SKU and GTIN in inspection documentation, store the pin in a clean, dry environment and include it in routine verification checks to ensure ongoing dimensional reliability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.89mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of high reproducibility, robust workshop construction and tight dimensional control to ensure reliable end‑dimension checks in production and inspection. Order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.I89 — Gauge pin, Ø 18.89 mm, length 50 mm, Metav IndustryLine Gauge pin M323.I89 is a single test pin intended for precise end‑dimension verification and fit control in workshop and quality‑assurance environments Workshop‑grade special steel construction Diameter 18.89 mm, length 50 mm Dimensional accuracy ±0.002 mm Ideal for end‑dimension checking Precision where final fit matters The gauge pin M323.I89 is manufactured for repeatable, end‑dimension verification where small deviations matter. With a nominal diameter of 18.89 mm and a length of 50 mm, the pin provides a stable reference for bore checks, go/no‑go testing and comparative inspection tasks. The specified ±0.002 mm tolerance defines the allowable deviation and supports tight acceptance criteria in quality control procedures; in practice this level of accuracy shortens decision time at the inspection bench and reduces the risk of production rework. Robust workshop construction for daily use Made from special steel and produced in a workshop‑grade execution, the pin resists wear from repeated seating and withdrawal in bores and gauges. The solid construction translates into consistent contact conditions and therefore improved repeatability of measurements over time. At a handled weight of 0.15 kg the component is substantial enough to feel secure in use yet compact for bench storage. These attributes support uninterrupted inspection workflows and reduce the frequency of tool replacement. Practical handling and inspection applications Designed as a single test item for end‑dimension and fit control, the pin is suited to quick functional checks and integration into standard inspection jigs. Operators benefit from a simple, robust geometry that minimises measurement variables: the cylindrical reference surface concentrates the control task on diameter and concentricity, while the length provides a useful reference for short bores and seat depths. Where clear specification of final mating condition is required, this component offers a pragmatic, low‑complexity solution that complements calipers and plug gauges. Contact Metav Werkzeuge today to discuss how the M323.I89 gauge pin from Metav IndustryLine can be integrated into existing inspection routines or measurement fixtures Technical data Article number: M323.I89 GTIN: 4061905071195 Category: Gauge pins Facts Diameter: 18.89 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Workshop version Single test pin Story trigger: end‑dimension checks FAQ What material is the pin made from? The gauge pin M323.I89 is manufactured from special steel, specified for workshop use and designed for mechanical durability in repeated inspection tasks. What is the dimensional tolerance of this test pin? The item delivers a dimensional accuracy of ±0.002 mm, making it suitable for tight end‑dimension verifications and fit assessments. Which inspection tasks is this pin suited to? The pin is intended for end‑dimension checks, bore verification and fit control where a precise cylindrical reference is required. What identifiers belong to this product? This product is listed as M323.I89 (SKU) with GTIN 4061905071195 and is part of the Metav IndustryLine gauge pin range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.8mm Test Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of robust workshop construction and high repeatability: the combination of Ø 18.8 mm diameter, 50 mm length and a stated dimensional accuracy of ±0.002 mm supports reliable end-measure checks and reduces rework. Order or request technical details via Metav Werkzeuge for rapid clarification. Inspection pin, single — Ø 18.8 mm, 50 mm length (Metav IndustryLine) The inspection pin is a workshop-grade test probe designed for precise end-measure verification and fixture checks in production and maintenance environments. Workshop-grade construction Diameter 18.8 mm for end-measure checks Length 50 mm for deep fixture access Dimensional accuracy ±0.002 mm Accurate end-measure control for reliable pass/fail decisions The probe delivers repeatable measurements thanks to its tight tolerance of ±0.002 mm, which supports consistent quality decisions on the shop floor. This level of precision minimises ambiguous results during incoming inspection or assembly control and contributes directly to reduced rework and improved first-pass yield. The stated accuracy is particularly relevant where small deviations translate into functional issues further down the production chain, so the pin functions as a compact, deterministic reference in gauging nests and check fixtures. Robust build for daily workshop handling Constructed from special steel and specified as a workshop execution, the probe withstands frequent handling and contact with toolroom environments while maintaining geometric integrity. With a 50 mm overall length it reaches into many fixture geometries without compromising stiffness, and the Ø 18.8 mm diameter provides a stable contact face for end-measure applications. The component's mass and geometry help reduce bending under normal use, which keeps measured values repeatable across many cycles and supports efficient, one-person handling in production or maintenance tasks. Traceable identification and simple integration into workflows The article is supplied individually and carries the stock identifier M323.I80 along with GTIN 4061905449871, enabling straightforward inventory control and traceability within existing procurement and quality-management systems. The probe integrates easily as a reference element in modular fixtures or as a spare gauge pin in inspection benches, providing a standardised, serviceable component that fits common workshop procedures. The use of familiar materials and dimensions keeps replacement and interchangeability uncomplicated across production lines. For dependable end-measure control in workshop environments, request a detailed data sheet from Metav Werkzeuge or enquire about batch availability from Metav IndustryLine via Metav Werkzeuge. Technical data SKU: M323.I80 GTIN: 4061905449871 Label: Prüfstift, einzeln, 18,8 mm Länge 50 mm Facts Diameter: 18.8 mm Length: 50 mm Weight: 0.15 kg Dimensional accuracy: ±0.002 mm Special features Material: special steel Workshop execution Supplied individually Category: test pins (Messstifte) FAQ What is the intended use for this inspection pin? This inspection pin is intended for end-measure verification and fixture checks in workshops and production lines, serving as a compact reference element for repeatable measurements. Which dimensions define the probe? The probe has a diameter of 18.8 mm and an overall length of 50 mm, identified in stock as M323.I80 for inventory and traceability. How precise is the component for gauging tasks? Dimensional repeatability is specified as ±0.002 mm, making the pin suitable for precise pass/fail inspections and routine fixture validation. Is the item traceable for procurement and quality records? Yes, the product is listed under SKU M323.I80 and GTIN 4061905449871 for straightforward traceability in quality and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.91mm Gauge Pin, Single, 50mm Length Workshop Version - Metav IndustryLine
Take advantage of a workshop-grade measuring solution that pairs high dimensional accuracy with robust construction for routine inspection tasks; the combination of Ø 18.91 mm diameter and ±0.002 mm tolerance ensures reproducible end‑dimension checks and reduces rework. Order the gauge pin directly via Metav Werkzeuge or ask our consultants for application advice. Gauge pin, single, 18.91 mm (length 50 mm) – workshop‑grade precision pin (Metav IndustryLine) The Gauge pin, single, 18.91 mm (length 50 mm) is a compact workshop instrument designed for precise end‑dimension verification and fixture alignment in metalworking and quality control environments. Precision diameter 18.91 mm Measuring length 50 mm High accuracy ±0.002 mm Workshop version with transport case Precision where small tolerances matter A compact measuring element delivers reliable, repeatable checks when manufacturing tolerances are tight. The M323.I91 gauge pin features a Ø 18.91 mm nominal diameter combined with a declared ±0.002 mm deviation, which provides measurable assurance for final‑dimension inspections. Classified in the micro range (measurement span within 10–100 mm), this size is ideal where short jaws and minimal deflection are beneficial: fine mechanical parts, small bores and delicate assemblies profit from the pin’s low bending tendency and consistent contact geometry. The clear numeric tolerance offers an immediate decision basis for acceptance or rework, supporting lean inspection routines. Robust workshop construction for everyday use Built as a workshop‑grade instrument, the pin is machined from special steel for wear resistance and dimensional stability under repeated use. The 50 mm working length balances insertion depth and handling comfort, while the compact mass (approx. 0.15 kg) makes placement and removal straightforward during batch sampling. Delivered in a dedicated transport case, the pin is protected in transit and storage — a practical detail that preserves calibration and surface condition between inspections. The construction emphasises durability without sacrificing the fine runout and concentricity required for reliable plug‑type gauging. Fits into established inspection workflows and tooling The gauge pin integrates seamlessly with existing fixtures, plug gauges and comparator setups, supporting repeatable checks at incoming inspection, in‑process control and final verification. Traceable identification (SKU M323.I91, GTIN available) simplifies inventory and quality records, while the precise nominal diameter reduces measurement uncertainty when used as a reference artefact. For production environments seeking to lower scrap rates and speed go/no‑go decisions, the pin acts as a simple, dependable standard that streamlines routine metrology tasks and improves throughput. Contact Metav Werkzeuge for tailored advice on workshop‑grade gauge pins and to ensure the right specification for the intended application; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M323.I91 GTIN: 4061905071218 Label: Gauge pin, single, 18.91 mm length 50 mm Core specifications Diameter: 18.91 mm Length: 50 mm Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Delivery: Transport case Category: Gauge pins FAQ What is the declared tolerance of this gauge pin? The declared tolerance of the M323.I91 gauge pin is ±0.002 mm, suitable for fine end‑dimension verification in precision workshops. Is the pin supplied ready for use or does it require calibration? The gauge pin is supplied ready for use; standard factory tolerances apply and traceable identification (SKU M323.I91) is provided for quality records. Which applications is this pin best suited for? This workshop‑grade pin is suited to end‑dimension checks, fixture alignment and plug‑type verification of small bores and mechanical components. What material is the pin made from and why does it matter? The pin is manufactured from special steel to ensure wear resistance and dimensional stability under repeated use, preserving the nominal diameter during routine inspection. Can this pin be integrated into existing gauging fixtures? Yes, the M323.I91 gauge pin is compatible with standard fixtures and plug gauges, offering a compact reference for repeatable checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.92mm Gauge Pin, Special Steel, 50mm Length, Workshop Version, Supplied in Case - Metav IndustryLine
Combining workshop‑ready robustness, Special steel construction and a tight tolerance of ±0.002 mm makes this single gauge pin a reliable choice for repeatable end‑size checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.I92 — single precision pin, 18.92 mm Ø, 50 mm length | Metav IndustryLine M323.I92 is a single precision gauge pin designed for end‑size inspection and dimensional verification in workshop metrology. Workshop version for robust use Diameter 18.92 mm with ±0.002 mm precision 50 mm pin length for stable handling Made from Special steel for wear resistance Consistent accuracy that reduces rework The pin delivers a declared ±0.002 mm runout, providing a measurable reduction in inspection uncertainty for small‑bore and end‑size assessments. Placed in the Micro range (10–100 mm) classification, this single‑piece gauge is optimised for fine mechanical and workshop tasks where short measurement spans demand high stiffness and minimal deflection. The tight tolerance narrows the window for batch rejection and supports faster decision‑making in quality control. Built for the workshop: durable and easy to handle Constructed from Special steel, the component balances surface hardness with corrosion resistance for frequent use on the shop floor. The 50 mm length offers a tactile, controllable grip during manual checks while maintaining a compact form factor that resists twisting under hand pressure. These attributes translate into longer service life and fewer replacements, which benefits maintenance planning and keeps inspection throughput steady. Traceable hardware that fits production workflows With a clear SKU and GTIN: 4061905071225, the pin supports inventory management and traceability within a calibrated metrology environment. Intended for end‑size verification, the single gauge pin integrates simply with existing plug gauge sets or measuring fixtures and provides a straightforward reference for go/no‑go checks. The combination of workshop design and precise geometry helps maintain reproducible results across shifts and operators, contributing to measurable process stability. For application advice or to secure stock of the Metav IndustryLine M323.I92 gauge pin, contact Metav Werkzeuge in Emmerich for tailored recommendations and fast processing Technical Data Article number: M323.I92 GTIN: 4061905071225 Manufacturer: Metav IndustryLine Facts Diameter: 18.92 mm Length: 50 mm Tolerance / Accuracy: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Version: Workshop execution Type: Single gauge pin Intended use: End‑size inspection and dimensional verification FAQ What measurement accuracy can be expected from this pin? The gauge pin M323.I92 is specified with an accuracy of ±0.002 mm, suitable for high‑precision workshop checks and end‑size verification. Is the material suited to frequent use in a production environment? Yes, the M323.I92 is made from Special steel and supplied in a workshop execution intended to withstand regular handling and inspection routines. Which measurement category does this pin belong to? With a diameter of 18.92 mm, the pin falls into the Micro range (10–100 mm), making it suitable for compact, high‑precision measurements. Can this pin be used as a reference in plug gauge sets? The single precision pin is appropriate for integration into manual plug gauge checks and as a reference element for go/no‑go assessments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.93mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Precision inspection assured by the combination of a ±0.002 mm tolerance and a special steel construction in a compact 50 mm length. Benefit from a robust workshop specification and straightforward procurement: order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.I93 — Ø 18.93 mm, 50 mm length (Metav IndustryLine) The gauge pin for quick dimensional checks and workshop inspection tasks, with a nominal diameter of 18.93 mm and an overall length of 50 mm. Precision tolerance ±0.002 mm Diameter Ø 18.93 mm 50 mm overall length, workshop version Special steel construction Accurate inspection that speeds up quality checks The compact design delivers repeatable results in routine inspection processes: a fine tolerance of ±0.002 mm ensures that pass/fail decisions and go/no-go evaluations can be made with confidence. The measured diameter of Ø 18.93 mm and the modest length reduce wobble during insertion, which helps preserve measurement integrity. As a single plug-style gauge pin, it is well suited for short-cycle checks on assemblies and components where quick verification is essential to maintain production flow. The combination of dimensional stability and clear nominal values supports faster decision-making on the shop floor and in incoming‑goods inspection. Robust material for regular workshop use Constructed from special steel, this gauge pin has been specified for durability under frequent handling. The material choice provides resistance against everyday wear and keeps surface integrity over many cycles of use, which in turn reduces the need for early replacement. The workshop execution (Werkstatt-Ausführung) indicates a build geared towards practical, hands-on environments where tools are expected to tolerate regular use without specialised handling. This makes the part economical for routine quality assurance tasks while still delivering the precision required for mechanical and metalworking contexts. Practical dimensions and handling benefits With an overall length of 50 mm and a weight of 0.15 kg, the pin is easy to position and manipulate in confined or awkward measurement situations. The compact length lowers leverage and the risk of deflection, thereby improving the reliability of short-range diameter checks. For operators, the modest mass and balanced geometry make insertion and extraction straightforward during repetitive checks, reducing operator fatigue and improving throughput. Where a single, precise reference diameter is needed, this component functions as a dependable, low‑complexity solution that integrates smoothly with standard inspection jigs and fixtures. Fit for purpose in inspection workflows The M323.I93 from Metav IndustryLine is designed as an individual gauge pin for direct use in workshop and inspection applications. Its nominal diameter and tight tolerance make it suitable for end‑dimension checks and for validating bore sizes where a single reference gauge is required. The clear specification simplifies part selection in purchasing and technical documentation, and the solid construction minimises downtime associated with tool replacement. For organisations seeking a pragmatic, accurate measuring aid, this gauge pin supports consistent quality monitoring in daily production routines. For precise inspection needs, contact Metav Werkzeuge to request the M323.I93 gauge pin and receive tailored application advice from our specialists in Emmerich. Technical Data Article number: M323.I93 GTIN: 4061905071744 Manufacturer: Metav IndustryLine Material: Special steel Weight: 0.15 kg Nominal diameter: 18.93 mm Overall length: 50 mm Tolerance: ±0.002 mm Core specifications Diameter Ø: 18.93 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Workshop execution Single gauge pin (individual supply) SKU: M323.I93 Category: Gauge pins / Messstifte FAQ What tolerance does the M323.I93 gauge pin offer? The M323.I93 gauge pin from Metav IndustryLine is specified with a tolerance of ±0.002 mm for precise dimensional checks. What material is the gauge pin made from? The gauge pin is manufactured from special steel, chosen for wear resistance and suitability for regular workshop use. What are the dimensions and weight of the gauge pin? The pin has a nominal diameter of 18.93 mm, an overall length of 50 mm and a weight of 0.15 kg. Is the component supplied individually or as part of a set? This article is supplied as a single gauge pin (individual unit), intended for standalone inspection tasks. Which inspection tasks is this pin best suited to? The M323.I93 is suitable for quick pass/fail diameter checks, end-dimension verification and use as a reference gauge in workshop and incoming-inspection workflows. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.94mm Gauge Pin 50mm Length Workshop Version - Metav IndustryLine
Take advantage of the combination of 18.94 mm nominal diameter, a 50 mm usable length and a tight tolerance of ±0.002 mm for consistent end‑measure verification in the workshop; order the gauge pin directly via Metav Werkzeuge or consult the team for application advice. Gauge pin, single — 18.94 mm diameter, 50 mm length (Metav IndustryLine) Gauge pin, single 18.94 mm is a workshop‑grade cylindrical gauge for precise end‑measure and insertion checks in production and inspection environments. Precision diameter 18.94 mm ±0.002 50 mm length for insertion and end checks Special steel for robust workshop use Workshop version supplied as a single piece Reliable verification for repetitive end measurements Designed for consistent use in production and inspection routines, this gauge pin offers a nominal diameter of 18.94 mm with a verified tolerance of ±0.002 mm, which minimises uncertainty when checking end measures or locating holes. The combination of tight dimensional control and a short, rigid shaft keeps repeatability high in fast assembly or inspection cycles. This makes the component particularly suitable where quick go/no‑go decisions or calibration references are required within a bench or machine environment. Robust build for frequent handling and insertion cycles Machined from special steel, the pin resists wear and maintains its gauge over many insertion cycles, reducing the need for frequent replacement and lowering process interruptions. The 50 mm length balances handling convenience with sufficient engagement depth for secure contact during checks. Surface finish and material selection aim to reduce burr formation and stick‑slip when entering fits, contributing to reliable tactile feedback during manual or fixture‑assisted inspection tasks. Practical workshop integration and traceable use The workshop execution emphasises straightforward integration into existing fixtures and measuring jigs used on the shop floor. Marking and SKU notation simplify inventory handling and traceability: this single gauge pin is identified as SKU M323.I94, making stock control and replacement planning convenient. Due to its focused design, it supports fast throughput in routine quality control and can serve as a reference element in setup procedures or comparative checks. Discuss application specifics with Metav Werkzeuge for a tailored recommendation based on the inspection task and fixture geometry Technical data SKU: M323.I94 GTIN: 4061905071751 Category: Gauge pins Version: Workshop version Numbers / Core technical data Nominal diameter: 18.94 mm Usable length: 50 mm Dimensional tolerance: ±0.002 mm Weight: 0.15 kg Materials & special features Material: Special steel Design: Single gauge pin for end‑measure verification Typical application: End‑measure and insertion checks Supply form: Single piece FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 18.94 mm with a stated dimensional tolerance of ±0.002 mm, suitable for precise end‑measure verification. Is this pin suitable for repeated insertion into press fits? Yes, the pin is made from special steel and the workshop design is intended for robust, repetitive use in insertion and end‑measure checks. How is the item identified for stock and ordering? This single gauge pin is listed under SKU M323.I94 and can be ordered through Metav IndustryLine channels. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.95mm Gauge Pin, Single, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of tight tolerance (±0.002 mm), special-steel construction and compact dimensions for dependable end-measurement checks. Order the gauge pin directly via Metav Werkzeuge or consult the specialists for application advice. Gauge pin, single, 18.95 mm diameter, 50 mm length — Metav IndustryLine precision gauge pin The gauge pin, single 18.95 mm diameter and 50 mm length, serves as a hardened reference element for end-measure verification and fixture checks in workshop and inspection environments. Workshop version for robust shop use Diameter 18.95 mm and length 50 mm Tolerance ±0.002 mm for tight checks Made from special steel Precision that stabilises quality control A compact hardened measuring pin designed for repeatable end-measure checks brings measurable improvements to inspection routines. With a declared tolerance of ±0.002 mm, the pin provides a narrow acceptance band that reduces ambiguity during go/no-go assessments and minimises rework. The specified accuracy supports consistent gauging in assembly and toolmaking workflows, where small deviations lead to fitment issues. By converting a physical dimension into a reliable reference, this component shortens decision times on the shop floor and stabilises process capability. Robust design engineered for everyday workshop use Built as a workshop version, the pin combines practical dimensions with a sturdy material choice: special steel that resists everyday handling and the occasional impact typical in production environments. The compact 50 mm length and 18.95 mm diameter are sized for end-stop and plug applications without compromising handling convenience. Supplied in a protective transport case, the item reaches the bench ready for use and protected during storage or transit. The construction emphasises straightness and surface finish to ensure repeatable contact points and long service life under normal workshop conditions. Practical integration and traceability for inspection tasks The pin is suited to plug and end-measure tests, fixture set-up, and dimensional references where a fixed diameter is required. Marking and traceability are supported by clear item identification (SKU M323.I95, GTIN 4061905071768), simplifying inventory and inspection records. The combination of compact geometry and defined tolerance makes the component suitable as a reference element in jigs, checking fixtures and assembly aids, where a reliable, repeatable contact surface accelerates alignment and reduces measurement scatter in routine checks. For tailored advice or to order this Metav IndustryLine gauge pin directly from Metav Werkzeuge in Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com for prompt, expert support. Technical data SKU: M323.I95 GTIN: 4061905071768 Article: Gauge pin, single, 18.95 mm × 50 mm Facts Diameter: 18.95 mm Length: 50 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Material: Special steel Workshop version Supplied in protective transport case Category: Gauge pins FAQ What are the exact dimensions of the pin? The gauge pin has a diameter of 18.95 mm and a length of 50 mm as specified for end-measure applications. Which tolerance class applies to this measuring element? The measuring element is specified with a tolerance of ±0.002 mm, suitable for tight go/no-go and reference checks. Is the pin suitable for use in fixture set-ups and jigs? Yes, the gauge pin is intended for fixture set-up, end-measure verification and as a hardened reference in jigs and checking fixtures. What material is the pin made from and how does that affect use? The pin is manufactured from special steel, providing robustness for workshop handling and a stable contact surface for repeatable measurements. How can the product be identified and tracked in inventory? Identification is possible via SKU M323.I95 and GTIN 4061905071768, which facilitate inventory control and documentation in quality records. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.96mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of the combination of high repeatability, tight tolerance and robust workshop design for reliable end‑measurement control. The Ø 18.96 mm diameter and 50 mm overall length provide a compact reference that integrates easily into inspection benches and gauge assemblies. Order the test pin directly via Metav Werkzeuge or ask our consultants if needed. Test pin M323.I96 (Ø 18.96 mm, 50 mm length) – Metav IndustryLine Test pin M323.I96 is a precision inspection pin intended for end‑measurement and reference applications in workshop metrology and inspection fixtures. Precision tolerance ±0.002 mm Diameter Ø 18.96 mm Length 50 mm Special steel construction Workshop execution Consistent dimensional control for production workflows A compact reference element for dimensional checks, the test pin guarantees consistent repeatability when used in comparative or go/no‑go fixtures. The specified tolerance of ±0.002 mm supports fine control over manufacturing deviations and aids quick decision making on the shop floor. As a single, purpose‑built pin, it is suitable for incorporation into manual gauges, transfer stages and fixture locators where a stable datum and minimal variation are essential. Design that supports fast inspection cycles The combination of Ø 18.96 mm nominal diameter and 50 mm length yields an element that is rigid enough for short‑span reference tasks yet compact for tight assemblies. The workshop execution denotes a practical balance between precision and handling: the profile resists minor knocks and can be handled without complex clamping, reducing time per check and raising throughput. Where short cycle times and repeatable outcomes matter, this configuration reduces fixture rework and measurement drift. Material choice and traceability for long‑term use Manufactured from special steel, the pin offers wear resistance suitable for repeated contact in inspection routines and maintains dimensional stability under normal workshop conditions. Traceability is supported by the listed identifiers (GTIN 4061905071775, SKU M323.I96), which simplify inventory and quality records. When integrated into a controlled inspection process, the pin becomes a reliable reference that contributes to consistent component quality across production batches. Contact Metav Werkzeuge for availability of the Metav IndustryLine test pin and to discuss supply or specification requirements for workshop inspection systems Technical data SKU: M323.I96 GTIN: 4061905071775 Brand: Metav IndustryLine Weight: 0.15 kg Facts Diameter: 18.96 mm Length: 50 mm Tolerance: ±0.002 mm Special features Material: Special steel Configuration: Single test pin Intended use: Workshop inspection and reference gauging FAQ What tolerance can be expected from this test pin? The test pin M323.I96 is specified with a tolerance of ±0.002 mm, making it suitable for fine inspection tasks and tight comparative gauges. Which environments is the pin designed for? Produced in a workshop execution and made from special steel, the pin is intended for regular shop‑floor use in inspection benches and fixture assemblies. Can this pin be used as a reference in gauge fixtures? Yes, the M323.I96 is designed for incorporation into gauge fixtures and transfer jigs where a stable end‑measurement datum is required. How is the component identified for traceability? Identification is facilitated by the GTIN 4061905071775 and SKU M323.I96, supporting inventory control and quality documentation. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18.97mm Gauge Pin 50mm Length Workshop Version, Special Steel - Metav IndustryLine
Take advantage of a workshop-grade inspection pin that combines high repeatability, a nominal diameter of 18.97 mm and a tight tolerance of ±0.002 mm to speed up acceptance checks and reduce rework. The compact 50 mm length and robust special-steel construction make this pin a reliable element for go/no-go fixtures or length gauges; order directly via Metav Werkzeuge or consult their specialists for application advice. Test pin, single, diameter 18.97 mm, length 50 mm — Metav IndustryLine A Test pin, single, diameter 18.97 mm, length 50 mm designed as a workshop-grade inspection component for repeatable dimensional checks and fixture use. Workshop-grade execution for robust use Diameter 18.97 mm with ±0.002 mm tolerance 50 mm length for stable seating Made from special steel for long service life Precision that reduces inspection time The inspection pin is engineered to deliver consistent measurement results with a specified tolerance of ±0.002 mm, which directly improves pass/fail decisions in production control. A nominal diameter of 18.97 mm and tightly controlled manufacturing variability mean fewer uncertain measurements and a reduced need for secondary checks; this increases throughput in repetitive inspection tasks and minimises stoppages caused by ambiguous results. The benefit is quantifiable: reduced cycle time for gauge checks and a sharper statistical basis for quality decisions. Built to withstand workshop conditions Designed as a workshop-grade item, the component uses special steel to combine wear resistance with stability under repeated use. The 50 mm effective length provides a stable seating depth in fixtures and reduces bending moments during manual handling, so measurements remain more reproducible over time. The single-piece design simplifies insertion into existing gauge holders or bespoke fixtures; the result is durable performance with low maintenance effort, supporting continuous inspection routines in machine shops and toolrooms. Traceability and integration into inspection routines Supplied as a single item and identified by article number M323.I97, the pin integrates easily into established gauge sets and inspection protocols. The compact format is particularly useful where space is limited but dimensional certainty is essential, for example in final inspection jigs or comparative master checks. With clear numerical specifications and a robust material choice, the component supports consistent documentation and audit trails in quality systems, making it straightforward to reference in inspection reports and measurement logs. For assistance with selecting the right Metav IndustryLine inspection components or to check availability of item M323.I97, please contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: M323.I97 GTIN: 4061905071782 Label: Test pin, single, diameter 18.97 mm, length 50 mm Material: Special steel Feature: Workshop-grade Facts Length: 50 mm Nominal diameter: 18.97 mm Tolerance: ±0.002 mm Weight: 0.15 kg Special features Single inspection pin Robust workshop execution Suitable for go/no-go and seating checks Identified by M323.I97 FAQ What is the nominal diameter and tolerance of this inspection pin? The inspection pin has a nominal diameter of 18.97 mm with a specified tolerance of ±0.002 mm for repeatable dimensional inspection. What is the overall length of the component? The component has an overall length of 50 mm and is intended for stable seating in fixtures and gauge holders. Which material is used for the pin? The pin is made from special steel, specified for wear resistance and durability in workshop environments. Is the item supplied individually or in sets? The product is supplied as a single inspection pin under article number M323.I97. For which inspection tasks is this pin most suitable? The pin is suitable for go/no-go checks, seating and length verification in workshop fixtures and gauge assemblies where a compact, precise master is required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com