Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
6.1mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of micrometric accuracy, compact dimensions and robust workshop design to speed up end‑measure checks and reduce rework. Order the gauge pin directly via Metav Werkzeuge or contact the consultants for tailored inspection advice. Gauge Pin M323.610 — Single precision test pin, 6.10 mm dia, ±0.001 mm A Gauge Pin M323.610 is a single test pin designed for precise end‑measure verification in workshop and shop‑floor inspection tasks. Precision tolerance ±0.001 mm Diameter 6.10 mm, ground finish Length 50 mm for end‑measure checks Supplied in transport case Precision that removes doubt The nominal 6.10 mm diameter and the ±0.001 mm tolerance are intended for applications where repeatable end‑measure verification is critical. Ground and finished to tight limits, the pin functions as a reference standard for plug checks, calibration fixtures and comparative gauges, giving a clear quantitative basis for acceptance or rejection decisions. The micro‑scale tolerance reduces uncertainty in pass/fail assessments and shortens decision cycles in quality control. Robust construction for everyday workshop use Made from special steel, the test pin combines corrosion‑resistant surface quality with the stiffness required for repeated seating in bores and fixtures. The workshop version denotes a build optimised for frequent handling: low mass (approx. 0.015 kg) and a 50 mm shank length that is long enough for stable seating yet compact for tight setups. Supplied in a dedicated transport case, the item reaches the bench protected against knocks and contamination, maintaining accuracy between uses. Integrates into inspection routines with minimal effort As a single test pin for end measures, the component is suitable for quick go/no‑go checks, pin‑gauge stacks and fixture templates. Its defined diameter and length simplify documentation of measurement steps and support traceable inspection procedures. The compact size and consistent geometry permit rapid swapping in jigs and checking stations, improving throughput on repetitive tasks while preserving metrological reliability. Procurement confidence and operational benefits Sourcing this gauge pin through a specialist distributor contributes to reliable supply and consistent quality. Metav’s emphasis on democratising precision ensures availability and practical aftermarket guidance, reducing the administrative effort for procurement teams. Combined with clear technical data and workshop‑oriented packaging, the product supports a straightforward integration into established quality workflows. Contact Metav Werkzeuge for expert advice on integrating this Metav IndustryLine gauge pin into inspection routines and to discuss supply options tailored to current production needs. Technical data SKU: M323.610 GTIN: 4061905060397 Brand: Metav IndustryLine Facts Diameter: 6.10 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Special features Material: Special steel Workshop execution Supplied in transport case FAQ What is the intended use of this gauge pin? The gauge pin M323.610 is designed for precise end‑measure verification, plug checks and fixture reference tasks on the shop floor. Is the tolerance of ±0.001 mm sufficient for calibration references? Yes, the ±0.001 mm tolerance makes the M323.610 suitable as a reference in many workshop inspection scenarios where micrometric precision is required. Can this pin be used in automated inspection jigs? The compact diameter and consistent geometry of the gauge pin permit integration into jigs and automated fixtures where a single reference pin is needed. How is the gauge pin protected during storage and transport? The product is supplied in a transport case to protect the finished surface and preserve dimensional integrity between uses. Which material is used and what are its advantages? Constructed from special steel, the pin offers a combination of surface stability and mechanical stiffness appropriate for frequent seating and repetitive inspection operations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.21mm Gauge Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
High-precision gauge pin with a 6.21 mm diameter and ±0.001 mm tolerance delivers repeatable end‑measurements; the 50 mm length and workshop-grade construction ensure robust handling and traceable checks. Order the gauge directly via Metav Werkzeuge or consult our advisors for batch supply and technical guidance. Gauge pin M323.621 (6.21 mm, ±0.001 mm) — Metav IndustryLine workshop version The Gauge pin M323.621 is a workshop-grade inspection pin designed for high-precision end‑measurement, plug and ring checks and fixture set-up in maintenance and production environments. Workshop-grade precision ±0.001 mm Diameter 6.21 mm ground to tolerance 50 mm special steel shaft for dependable wear resistance Delivered in protective transport case Repeatable accuracy where it matters Precision is the primary value of this inspection pin. With a specified tolerance of ±0.001 mm, the pin supports reliable go/no‑go and comparative checks that reduce uncertainty during incoming inspection or in‑process control. The compact diameter of 6.21 mm and moderate 50 mm length make the item suitable for tight bores and confined measuring spaces, while the fine tolerance helps to detect minute deviations that would otherwise affect assembly or function. The technical specification is ideal for workshop applications where small form‑factor precision tools are required. Built for workshop use and sustained service life The workshop version is engineered for everyday inspection routines. Manufactured from special steel, the shaft offers a balance of hardness and toughness that resists rapid wear under repeated contact inspections. The single‑piece supply simplifies inventory selection for toolrooms and gauges, and delivery in a protective transport case preserves the ground surface and concentricity during storage and transit. Together, these attributes lower the total cost of ownership by extending service intervals and maintaining measurement integrity between checks. Integrates cleanly into quality control processes As a precision inspection element, this gauge pin fits directly into established quality workflows: setting ring gauges, verifying bore diameters, and confirming fit tolerances on assemblies. The compact format supports rapid interchange and reduces handling time on the shop floor, contributing to faster inspection cycles and more consistent acceptance decisions. For those tracking inventory or referencing product data, the item is listed under SKU M323.621 and is supplied as an individual gauge pin suitable for routine dimensional control tasks. For sample requests, calibration options or volume supply, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or by email at info@metav-werkzeuge.com for personalised advice and delivery details Technical data Article number: M323.621 GTIN: 4061905061493 Brand: Metav IndustryLine Specifications Diameter: 6.21 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Features Workshop version Material: Special steel Supplied individually Protective transport case included FAQ What tolerance does this gauge pin provide? The inspection pin is specified with a tolerance of ±0.001 mm, suitable for high‑precision end‑measurement. What material is the shaft made from? The shaft is manufactured from special steel intended for workshop use and durable contact inspections. Is the gauge pin supplied individually or as a set? This item is supplied as an individual gauge pin under SKU M323.621. Which inspection tasks is this pin intended for? Typical uses include plug and ring checks, bore verification and fixture set‑up where a compact, precision pin is required. Does the product description include a calibration certificate? The product data does not specify an included calibration certificate; calibration status is not stated. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.22mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial-grade precision, a tight ±0.001 mm tolerance and a compact 50 mm length for reliable inspection and repeatable assembly checks; order the gauge pin directly via Metav Werkzeuge or consult the Metav experts for application advice. Gauge pin M323.622 — Test pin, 6.22 mm, ±0.001 mm (Metav IndustryLine) Gauge pin M323.622 is a single precision test pin intended for dimensional inspection and reference checks in workshop and production environments Diameter 6.22 mm precision Tolerance ±0.001 mm Length 50 mm workshop version Special steel construction Consistent dimensional control for everyday inspection tasks The compact design of this test pin delivers a clear benefit where repeatability matters: the nominal diameter 6.22 mm combined with a certified ±0.001 mm runout tolerance supports tight go/no‑go checks and reference measures. In practical terms, the small mass and controlled geometry reduce handling variation during sequential checks, improving repeatability on the shop floor. The specified 50 mm length offers sufficient engagement for bore and plug inspections while remaining easy to handle in jigs and fixtures. This balance of dimensions and tolerance translates directly into fewer measurement-related reworks and steadier quality control routines. Robust handling and fit for production environments Constructed from special steel, the pin is designed for stable dimensional behaviour under routine use and provides a reliable seating for comparative gauging and fixture set‑ups. The plain cylindrical form minimises seating errors and simplifies alignment in distinguishing bore limits or establishing reference lengths. Where quick, unequivocal verification is required during assembly or incoming‑goods inspection, the compact test pin serves as a fast, deterministic check that integrates with manual and semi‑automated inspection processes. The modest weight makes it convenient for bench tasks and for inclusion in inspection sets without affecting ergonomics. Integration into metrology workflows and documentation As an inspection tool from Metav IndustryLine, the pin is intended to complement existing measurement artefacts and gauge blocks in a calibrated toolbox. Its use-case extends from quick pass/fail checks to inclusion as a control gauge in first‑article inspection reports. The clearly defined tolerance band simplifies statistical process control entries and helps to document measurement traceability when logged with batch or process data. For customers requiring catalogue and traceability alignment, the item’s SKU and GTIN facilitate stockkeeping and integration into procurement or calibration records. Secure precise reference parts from Metav Werkzeuge — order the Metav IndustryLine M323.622 gauge pin or contact the Metav team in Emmerich for technical matching to specific inspection tasks Technical Data Article number: M323.622 GTIN: 4061905061509 Brand: Metav IndustryLine Type: Single gauge pin / test pin Data Diameter: 6.22 mm Length: 50 mm Tolerance / accuracy: ±0.001 mm Weight: 0.015 kg Special features Workshop version Material: Special steel Single item delivery SKU: M323.622 FAQ What is the primary use of this gauge pin? The gauge pin M323.622 is intended for dimensional inspection and reference checks, used as a go/no‑go or seating reference in bore and plug verification tasks. Does the pin meet very fine tolerance requirements? Yes, the pin is specified with a tolerance of ±0.001 mm, suitable for high‑precision shop and inspection applications where tight limits are required. Which material is the pin made from and what does this mean for durability? The pin is made from special steel, offering stable dimensional behaviour and wear resistance appropriate for regular inspection cycles in production environments. Can this pin be used in fixture set‑ups and jigs? Its 50 mm length and cylindrical form make it suitable for integration into fixtures and jigs as a reference element for alignment and verification tasks. How is the part identified for procurement and inventory? Stock and procurement reference is SKU M323.622 with GTIN 4061905061509 for clear traceability in ordering and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.23mm Gauge Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine tolerance, compact dimensions and robust workshop design for reliable end‑dimension checks; the test pin is delivered in a transport case for safe handling and quick storage. Order the M323.623 gauge pin directly via Metav Werkzeuge or consult our advisors for application support. Gauge pin M323.623 — precision 6.23 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.623 is a single precision test pin designed for rapid end‑dimension verification in workshop and production metrology, offering micron‑level repeatability for small‑part inspection. Precision tolerance ±0.001 mm Diameter 6.23 mm, length 50 mm Made from special steel Supplied in a transport case Engineered for dependable end‑dimension verification This compact test pin delivers an exact 6.23 mm nominal diameter with a ±0.001 mm tolerance, which places it in the high‑precision band for plug gauges and test pins. The tight tolerance supports reliable go/no‑go checks and repeatable measurement routines, reducing rework and downtime. As a solid test pin, it is particularly suitable for quick inspection of bore end‑masses and final dimensional checks where micrometre accuracy matters. Robust handling and workshop suitability Constructed from special steel in a workshop‑grade configuration, the pin balances wear resistance with manageable weight for daily use. The 50 mm length provides sufficient engagement in typical small bores while keeping handling straightforward on the shop floor. Supplied in a transport case, the item is protected in transit and ready for secure storage on the bench, preserving the measuring surface and extending service life. Traceability and integration into inspection routines The simple geometry and precise manufacturing of this plug gauge facilitate integration into standard inspection flows and fixture checks. Its repeatability makes it a pragmatic choice for batch verification and final QA gates, supporting process stability and clear pass/fail criteria. For those seeking a trusted supply chain partner, Metav Werkzeuge’s quality filter in Emmerich ensures consistent product availability and traceable sourcing for measurement tools. Contact Metav Werkzeuge in Emmerich for tailored application advice and swift supply of the M323.623 gauge pin Technical Data Article number: M323.623 GTIN: 4061905062322 Label: Prüfstift, einzeln, 6,23mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 6.23 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Special features Material: Special steel Version: Workshop design Supplied in transport case FAQ What tolerance does this test pin provide? The M323.623 gauge pin is manufactured to a tolerance of ±0.001 mm, offering micrometre‑level accuracy suitable for final dimensional checks. For which applications is this plug gauge intended? This precision pin is intended for end‑dimension verification and go/no‑go checks in production and workshop metrology, where small‑bore inspection and repeatable pass/fail criteria are required. How is the M323.623 delivered and protected? The gauge pin is supplied in a transport case to protect the measuring surface during storage and transit, preserving accuracy between uses. Can the pin be used for routine inspection on the shop floor? Yes, the workshop version of the M323.623 is designed for regular use in inspection stations and bench checks, combining robustness with precise geometry. Is the M323.623 suitable for integration into existing inspection fixtures? Its compact diameter and consistent manufacturing make the gauge pin straightforward to incorporate into fixtures for batch inspection and quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.24mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of extreme measuring precision, a compact 50 mm length and robust special steel construction to secure repeatable end‑dimension checks and reduce rework. Order the pin gauge directly via Metav Werkzeuge or consult the product advisors for application matching. Pin gauge M323.624 — single workshop‑grade gauging pin, Ø 6.24 mm, tolerance ±0.001 mm The Pin gauge M323.624 is a single, workshop‑grade measuring pin designed for reliable end‑dimension verification and go/no‑go fits in production and inspection environments Workshop‑grade precision construction Diameter 6.24 mm, tolerance ±0.001 mm 50 mm length for stable handling and reach Single unit delivery for targeted checks Precision that secures final dimensions The M323.624 delivers an exceptional ±0.001 mm tolerance on a nominal 6.24 mm diameter, making it suitable where micrometric conformity determines pass or fail at the final inspection stage. Such a tight tolerance removes ambiguity from end‑dimension checks and shortens decision paths on the shop floor: measurement results become comparable across shifts and machines, lowering scrap rates and reducing subsequent rework. The specification is especially valuable when used as a reference gauge in assembly jigs or as a benchmark during tool set‑up, where repeatable results are essential for production continuity. Robust build for everyday workshop use Manufactured from special steel, this single pin is intended for workshop environments and designed to withstand frequent handling without compromising accuracy. The 50 mm length provides a compromise between reach and rigidity, ensuring stable contacts in small bores or on turned parts while remaining easy to manoeuvre by hand. At approximately 0.015 kg the gauge is lightweight yet stiff enough to give reproducible readings; the compact form factor reduces the risk of levered deflection during measurement and supports faster inspection cycles in busy production lines. Practical applications that improve throughput This gauging pin is primarily intended for end‑dimension verification of shafts, holes and turned components, serving as a fast reference for go/no‑go decisions and routine quality control. Used in incoming inspection, in‑process checks and final acceptance, it supports a logic of quick, objective measurement rather than prolonged subjective assessment. The workshop execution makes it a dependable choice for maintenance shops, small batch production and fixture set‑ups where a precise, single‑diameter reference is required to maintain assembly tolerances and safeguard downstream processes. Contact Metav Werkzeuge today to confirm suitability of the M323.624 pin gauge for specific measurement tasks and to arrange supply directly from Emmerich: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: M323.624 GTIN: 4061905062339 Article: Pin gauge, single, Ø 6.24 mm, ±0.001 mm Facts Diameter: 6.24 mm Length: 50 mm Tolerance/accuracy: ±0.001 mm Weight: 0.015 kg Special features Material: special steel Workshop execution Single unit delivery Intended for end‑dimension checks FAQ What level of accuracy does the pin provide? The M323.624 pin gauge (Metav IndustryLine, pin gauge SKU M323.624) is specified with a tolerance of ±0.001 mm, suitable for high‑precision end‑dimension checks. Which measurement tasks is this gauge intended for? This single pin gauge is made for end‑dimension verification of shafts, bores and turned components and is suitable as a rapid go/no‑go reference in workshop and production inspection. What material is the pin made from and how does that affect use? The pin is produced from special steel, giving robust handling characteristics appropriate for workshop environments while maintaining the dimensional stability required for repeatable measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.25mm Gauge Pin ±0.001 mm Length 50 mm Workshop Finish - Metav IndustryLine
Take advantage of workshop‑grade construction, special‑steel durability and an exceptionally fine tolerance of ±0.001 mm to secure repeatable end‑measurement checks and jigging operations; order the gauge pin directly via Metav Werkzeuge or request advice from our consultants for batch requirements. M323.625 Gauge pin (6.25 mm, ±0.001 mm) — Metav IndustryLine The M323.625 gauge pin is a workshop‑grade precision plug designed for end‑measurements, go/no‑go checks and fixture setting in metrology and toolmaking environments. Precision tolerance ±0.001 mm Workshop‑grade special steel Length 50 mm for end measurements Delivered in a transport case High precision for consistent pass/fail verification The M323.625 is manufactured to an exacting tolerance of ±0.001 mm, which supports consistent go/no‑go assessments and dimensional spot checks on machined parts. That level of accuracy reduces the need for secondary verification and speeds up in‑process inspection, so batch acceptance decisions are based on reproducible, measurable criteria. The slim form makes the device suitable for plug and seat checks where surface conformity and bore concentricity are critical. Robust workshop design that withstands daily use Constructed from special steel and specified as a workshop‑grade tool, the pin is finished to resist wear from frequent handling and contact with mating parts. The 50 mm shank provides a stable reference length for end measurements and is long enough for most fixture and gauge applications while remaining easy to position. Supplied individually and protected for transit in a secure transport case, the component arrives ready for immediate use in production or toolroom environments. Fits into inspection workflows with clear traceability Marked with SKU M323.625 and the GTIN for inventory control, the pin integrates into standard inspection processes and documentation routines. Its small mass and compact dimensions allow simple handling and rapid changeover between checks, supporting lean metrology practices on the shop floor. Backed by Metav’s distribution and quality focus, the item benefits from a supply chain that emphasizes availability and consistent product quality for industrial and trade customers. Contact Metav Werkzeuge to discuss batch availability, sample inspection or to arrange delivery from Emmerich for your metrology and fixture needs Technical Data Article number: M323.625 GTIN: 4061905058790 SKU: M323.625 Facts Diameter: 6.25 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Special features Workshop‑grade design Material: special steel Delivered in transport case Single item supply FAQ What accuracy can be expected from this gauge pin? The M323.625 gauge pin is manufactured to a tolerance of ±0.001 mm, making it suitable for high‑precision pass/fail checks and precise fixture setting. Is the pin suitable for routine shop‑floor inspection? Yes, the workshop‑grade construction and protective transport case mean the gauge pin is designed for regular use in production and toolroom environments. Which material is used for the pin? The pin is made from special steel, chosen for wear resistance and dimensional stability during repeated contact inspections. How is the product identified for stock and traceability? The item is supplied with SKU M323.625 and the GTIN 4061905058790 for inventory control and documentation. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.26mm Gauge Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Combining ultra‑fine tolerance and a robust workshop design ensures reliable, repeatable inspections; benefit from the ±0.001 mm accuracy and compact 50 mm length when verifying small bores. Order the M323.626 gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. M323.626 gauge pin — 6.26 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) The M323.626 gauge pin is a single, high‑precision inspection pin for micro‑range dimensional checks in workshop and production environments. High precision ±0.001 mm tolerance Compact 6.26 mm diameter for micro checks Workshop‑grade construction for daily use Supplied in a protective transport case Precision that stabilises quality control Consistent measurement reduces rework and keeps production running to plan. The test pin delivers a diameter of 6.26 mm with a guaranteed ±0.001 mm tolerance, enabling reliable go/no‑go and reference checks on small bores and mating parts. Such fine tolerance minimises acceptance variance during incoming inspection and in‑process quality gates, so fewer components are rejected for marginal deviations and process capability is easier to maintain. Built for workshop resilience and simple handling Designed as a workshop version, the pin is manufactured from special steel to combine surface hardness with dimensional stability. With a length of 50 mm and a mass around 0.015 kg, it is straightforward to handle during manual inspection or when placed in a fixture. Delivery in a protective case reduces the risk of transport damage and helps preserve the geometry that underpins repeatable measurements, extending the useful life of the gauge. Straightforward integration into inspection routines The component supports traceable stock and quality processes via GTIN 4061905058806 and SKU M323.626, helping with inventory control and audit trails. As a micro‑range gauge (measurement range below 10 mm), the pin complements bench comparators and small‑bore fixtures, simplifying routine checks and accelerating quality verification. Because the design focuses on a single, well‑defined diameter, it is ideal for rapid verification tasks where speed and precision matter. For dependable micro‑inspection in daily production, contact Metav Werkzeuge in Emmerich to discuss how the Metav IndustryLine M323.626 gauge pin fits specific inspection workflows Technical data Article number: M323.626 GTIN: 4061905058806 Manufacturer: Metav IndustryLine Category: Gauge pin / Test pin Facts Diameter: 6.26 mm Tolerance / Accuracy: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Material: Special steel Workshop execution Supplied in a transport case Intended use: dimensional inspection of small bores FAQ What tolerance class does this pin have? The M323.626 gauge pin is specified with an accuracy of ±0.001 mm, suitable for high‑precision inspection tasks. Is the pin suitable for daily workshop use? Yes, the workshop execution and special steel construction make the inspection pin appropriate for frequent handling and routine checks. What is the measurement range classification for this item? This component falls into the micro range (measurement range below 10 mm), intended for fine mechanical and small bore applications. Does the product come with traceability identifiers? The gauge pin is identified by GTIN 4061905058806 and SKU M323.626 to support inventory and audit processes. How is the item delivered to protect dimensional integrity? The pin is supplied in a protective transport case to reduce the risk of damage in transit and preserve measurement geometry. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.27mm Test Pin ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of industrial precision and robust workshop design: the gauge presents a nominal diameter of Ø 6.27 mm with an ultra‑fine tolerance of ±0.001 mm, and a compact length of 50 mm for reliable end‑measure checks. Order the M323.627 directly via Metav Werkzeuge or request technical advice from our consultants. M323.627 Test Pin (Metav IndustryLine) – Ø 6.27 mm, ±0.001 mm, 50 mm M323.627 Test Pin is a single, workshop‑grade gauge pin for precise end‑measurement and fixture‑setting tasks in inspection and production environments. Workshop‑grade special steel construction Diameter Ø 6.27 mm with ±0.001 mm tolerance Length 50 mm for compact fixtures Delivered in protective transport case Accuracy that reduces rework and speeds inspection The gauge pin is specified with a tolerance of ±0.001 mm, which translates into highly repeatable pass/fail checks at the receiving end of production sequences. This level of precision supports decisive go/no‑go decisions during inline inspection and reduces costly rework by ensuring that bore and end‑dimension checks return consistent results. The clearly defined nominal diameter Ø 6.27 mm allows easy integration into existing plug gauges and test fixtures, improving throughput in quality control operations. Material and build tailored for workshop use Manufactured from special steel and labelled as a workshop version, the pin balances dimensional stability with everyday robustness. The combination of hardened machining and precise grinding yields a component that maintains geometry under normal handling and contact loads. The low mass (approx. 0.015 kg) and compact geometry contribute to effortless handling during repetitive inspection cycles while supporting long‑term serviceability in a busy production setting. Compact design and secure transport for on‑the‑job readiness With a length of 50 mm, the pin suits confined fixturing and quick insertion tasks where short gauges are required. Delivery in a protective transport case prevents incidental damage and keeps the pin ready for immediate use at the workstation or in a portable inspection kit. This practical packaging reduces downtime caused by handling damage and helps maintain the pin’s measurement integrity between uses. Practical uses and compatibility with inspection workflows Intended primarily for end measurements and plug‑type checks, the component is useful in assembly, fixture set‑up and repetitive quality checks where a defined reference diameter is needed. Its nominal diameter and tolerance make it suitable as a precision check gauge within production sampling plans and for aligning jigs or locating features. The compact design supports easy incorporation into handheld gauge sets and bench fixtures without disrupting established workflows. For reliable end‑measurement performance, choose the Metav IndustryLine M323.627 gauge pin — contact Metav Werkzeuge for procurement and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: M323.627 GTIN: 4061905058813 Label: Test pin, single, 6.27 mm, ±0.001 mm, length 50 mm Numbers / Core technical data Nominal diameter: 6.27 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Material: Special steel Workshop version Delivered in protective transport case Category: Messstifte Intended use: end measurements FAQ What tolerance and diameter does the M323.627 test pin offer? The Metav IndustryLine M323.627 test pin is specified at Ø 6.27 mm with a tolerance of ±0.001 mm, designed for highly repeatable end‑measurement checks. Is the gauge pin delivered ready for safe transport? Yes, the M323.627 is supplied in a protective transport case to prevent handling damage and to keep the pin ready for immediate use at the workstation. Which material is the pin made from and what does that mean in practice? The pin is made from special steel, providing dimensional stability and resistance to normal workshop wear, which helps preserve measurement integrity during routine use. For which inspection tasks is this test pin best suited? The pin is ideal for end‑measurement checks, plug‑type inspections and fixture alignment where a compact, high‑precision reference diameter is required. Can the M323.627 be integrated into existing fixtures and gauges? Yes, the compact 50 mm length and standardised nominal diameter make the pin suitable for integration into bench fixtures, handheld gauge sets and plug‑type measurement arrangements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.28mm Test Pin, Single, ±0.001mm, Length 50mm, Workshop Version - Metav IndustryLine
Take advantage of the proven combination of micrometre-level accuracy, compact handling and robust workshop design to secure repeatable end measurements and fewer rework cycles; order directly via Metav Werkzeuge or contact our consultants for technical advice. Gauge pin M323.628 (6.28 mm, ±0.001 mm, 50 mm length) — Metav IndustryLine The Gauge pin M323.628 is a single precision test pin for dependable end-measure checks and bore verification in workshop and inspection environments Diameter 6.28 mm, tolerance ±0.001 mm 50 mm length, workshop execution Made from special steel Supplied in protective transport case Micrometre-level tolerance for decisive quality control The core advantage lies in the ±0.001 mm specification, which translates into measurable gains in process reliability when verifying end measures and mating fits. For short-run inspections and final acceptance, the small geometric deviation reduces false rejects and minimises downstream correction work. Because the diameter is manufactured to 6.28 mm with a narrow error band, the pin serves as a reliable reference for checking bore sizes and alignment during setup and routine quality control. The precision achieved here supports leaner inspection steps and faster go/no-go evaluations. Robust, compact design that endures workshop use Manufactured in special steel and executed as a workshop-grade component, this test pin balances hardness with corrosion resistance for everyday handling. The 50 mm length and low mass (approx. 0.015 kg) make the pin easy to manoeuvre while retaining stiffness for accurate seating in bores. Supplied in a protective transport case, the unit is protected from knocks and contamination between uses, which preserves dimensional stability and extends service life. The straightforward form factor also simplifies storage in inspection trays or gauge sets. Practical integration into inspection routines and tooling Designed for end-measure applications, this pin is suitable for direct bore checks, fixture setup and reference gauging. The compact geometry eases insertion in confined spaces and supports repeatable seating against datum faces, delivering consistent reference points for measurement chains. Supplied as a single unit with the clear designation M323.628, the pin complements standardised inspection jigs and can be used alongside callipers and micrometres to confirm critical dimensions during final inspection stages. Trusted supply chain and competence from Metav Metav IndustryLine benefits from the Metav quality filter in Emmerich, ensuring parts are sourced and handled with industrial discipline. The combination of clear traceability, a broad product range for workshops and a long-standing distribution network provides practical reassurance when specifying precision components. Metav’s portfolio and advisory capability help integrate measurement items such as this pin into everyday inspection infrastructure, supporting higher first-pass yields and dependable delivery performance. For reliable end measurements and workshop-ready inspection tooling, contact Metav Werkzeuge in Emmerich for availability and technical pairing advice — eMail info@metav-werkzeuge.com or call +49 2822 7131930 to discuss the M323.628 gauge pin and suitable complementary gauges Technical data Article number: M323.628 GTIN: 4061905058820 Label: Prüfstift, einzeln, 6,28mm, +/- 0.001 mm Länge 50 mm Manufacturer: Metav IndustryLine Facts Diameter: 6.28 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Material: special steel Workshop execution Supplied in protective transport case Intended application: end measurements Category: Messstifte FAQ What is the intended use of this gauge pin? The gauge pin M323.628 from Metav IndustryLine is intended for end-measure checks and bore verification in workshop and inspection environments. Is the diameter tolerance suitable for high-precision fits? Yes, the ±0.001 mm tolerance of the M323.628 test pin is suitable for precision fit verification and careful end-measure assessments. What material is used and how does it affect durability? Made from special steel, the pin offers a balance of wear resistance and dimensional stability suited to regular workshop handling. Does the product come with protective packaging? The pin is supplied in a protective transport case, ensuring safe handling and reduced contamination during storage and transport. How can this pin be integrated into existing inspection workflows? The compact 50 mm length and precise diameter allow the M323.628 gauge pin to be used for fixture setup, bore checks and as a reference in multi-step inspection routines with callipers or micrometres. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.29mm Gauge Pin Single ±0.001 mm Length 50 mm, Workshop Version - Metav IndustryLine
Take advantage of a compact inspection tool that delivers repeatable end-dimension control through a combination of ultra‑fine tolerance, stable geometry and robust workshop design; the precise ±0.001 mm specification and a 6.29 mm diameter ensure reliable fits and consistent measurements in series testing. Order directly via Metav Werkzeuge or contact their consultants for tailored advice. M323.629 gauge pin (6.29 mm, ±0.001 mm) – Metav IndustryLine The M323.629 gauge pin is a single inspection pin designed for precise end‑dimension checks and tight‑fit verification in workshop and production environments. High precision tolerance ±0.001 mm Diameter 6.29 mm for tight-fit checks Length 50 mm for fixture and bore tests Workshop version, robust industrial design Precise tolerance for reproducible end measurements The core strength of this inspection pin lies in its ±0.001 mm tolerance, which makes it suitable for applications where minute dimensional deviations matter. Specified accuracy removes ambiguity when validating final dimensions on moderate‑run parts. The tight tolerance reduces rework and supports confidence in pass/fail decisions during incoming inspection and assembly verification. As a verification tool, the pin gives measurable, comparable results that integrate readily into routine quality checks. Compact geometry that suits tight bores and jigs With a 6.29 mm diameter and 50 mm overall length, the pin is engineered for insertion into small bores, locating holes and jigs where standard gauges may be too large. The compact geometry helps maintain alignment in fixtures and minimises bending or rocking during measurement, so readings remain stable. This makes the component a practical choice for bench checks and for confirming end measurements on assembled modules where accessibility and repeatability are required. Robust material choice for consistent dimensional stability Manufactured from special steel, this single test pin is produced for workshop use and regular handling. The material selection supports dimensional stability under typical shop conditions and contributes to wear resistance over many cycles. The design intent is to provide a resilient inspection aid that sustains precise contact geometry when used in standard production and maintenance routines, thereby preserving measurement quality over time. Designed for integration into inspection workflows As a single, clearly identified inspection element with a unique SKU and GTIN, the pin is easy to log into quality records and inventory systems. Its straightforward form factor allows rapid substitution in modular gauges or fixture checks and supports consistent comparison across batches. For customers seeking reliable end‑dimension control without complex setup, this gauge pin provides a direct, low‑overhead method to confirm hole sizes and locating features during the production process. For reliable end‑dimension inspection with the Metav IndustryLine gauge pin, contact Metav Werkzeuge for ordering and technical advice: info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M323.629 GTIN: 4061905058837 Category: Gauge pins Brand: Metav IndustryLine Facts Diameter: 6.29 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Special features Material: special steel Workshop version Single inspection pin Application: end‑dimension checks FAQ What is the declared tolerance of this inspection pin? The declared tolerance is ±0.001 mm for the M323.629 gauge pin, providing high‑precision control for end‑dimension verification. For which applications is this pin intended? This single test pin is intended for tight bore inspection, fixture checks and end‑dimension control in workshop and production environments. What material is used for the pin? The pin is made from special steel to offer dimensional stability and durability under routine inspection use. How long is the pin and which diameters does it suit? The pin has a length of 50 mm and a diameter of 6.29 mm, suited for small bores and locating features. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.2mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Grade - Metav IndustryLine
Take advantage of ultra‑fine tolerance (±0.001 mm) and a hard-wearing special‑steel construction combined with a compact 50 mm length for reliable end‑measure checks in everyday workshop use; order the M323.620 gauge pin directly via Metav Werkzeuge or consult our specialists for application guidance. M323.620 Gauge Pin — 6.20 mm, ±0.001 mm (Metav IndustryLine) The M323.620 is a single gauge pin designed for precise end‑measurement and fit checks in workshop environments, offering a compact 50 mm length and laboratory-grade dimensional stability. Ultra-fine tolerance ±0.001 mm Precisely ground Ø 6.20 mm Robust special-steel construction Workshop execution, length 50 mm Precision that shortens inspection cycles The M323.620 gauge pin was engineered to provide a clear, measurable benefit: repeatable dimensional control with a declared accuracy of ±0.001 mm. This level of precision minimises rework and reduces the time spent on secondary checks, making the gauge pin a practical tool for entry checks, end‑measure verification and go/no‑go fits. The 6.20 mm diameter is ground to size and held to tight tolerances, which supports consistent mating with fixtures and gauges and helps maintain throughput in small‑batch production or maintenance operations. Robust design for everyday workshop use Constructed from special steel, this single test pin resists everyday wear while maintaining surface integrity over many cycles. The workshop execution emphasises practical durability: surfaces are finely ground so that contact points stay stable, while the compact 50 mm length gives sufficient reach for most assembly and inspection tasks without adding unnecessary leverage or handling complexity. The low mass (approx. 0.015 kg) facilitates quick positioning and limits inertia during repeated measurements, improving operator handling and reducing measurement scatter. Integrates into quality workflows and traceability The gauge pin is supplied as a single, traceable item (GTIN: 4061905061486) suitable for use alongside existing plug‑gauge sets or as replacement pins in inspection rigs. Clear specification—diameter 6.20 mm, tolerance ±0.001 mm, length 50 mm—allows straightforward documentation in quality records and inventory systems. Relying on such defined physical parameters supports faster decision‑making on the shop floor, while the product’s straightforward geometry eases calibration planning and storage in controlled tool cabinets. Contact Metav Werkzeuge in Emmerich to discuss how the M323.620 gauge pin fits into your inspection process and to arrange expert technical advice or tailored supply. Technical data Article number: M323.620 GTIN: 4061905061486 Label: Prüfstift, einzeln, 6,20mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 6.20 mm Length: 50 mm Tolerance / Accuracy: ±0.001 mm Weight: 0.015 kg Special features Material: Special steel Version: Workshop execution Category: Gauge pin (single) Storytrigger / Application cue: end‑measure checks FAQ What level of dimensional accuracy does this gauge pin provide? The M323.620 gauge pin is specified to ±0.001 mm, making it suitable for high‑precision fit and end‑measure checks in workshop environments. Which materials is the pin made from and how does that affect wear? Manufactured from special steel, the M323.620 offers enhanced resistance to wear and maintains contact surface quality through repeated use. Can this pin be used in existing gauge sets or fixtures? Yes, the single‑piece design and standardised diameter of 6.20 mm mean the pin integrates easily with common plug‑gauge sets and inspection fixtures. Is the length suitable for recessed fit checks? The 50 mm length provides sufficient reach for many recessed and through‑hole verifications while remaining easy to handle during repetitive checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.31mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop durability, exacting ±0.001 mm tolerance and compact handling length for reliable end‑measure checks; order the part directly via Metav Werkzeuge or consult our advisors for batch and inspection advice. Gauge pin M323.631 – Single test pin, 6.31 mm ±0.001 mm, 50 mm A gauge pin M323.631 engineered for precise end‑measure verification and quick go/no‑go checks in workshop environments. High precision ±0.001 mm tolerance Robust workshop design for daily use Manufactured from special steel for wear resistance Stable 50 mm length for repeatable handling Accurate end‑measure verification without compromise The compact measuring element delivers repeatable results thanks to its ±0.001 mm tolerance and nominal diameter of 6.31 mm. This level of accuracy permits confident verification of end‑sizes, pins and bores where tight clearances determine fit and function. The single measuring pin concept keeps handling straightforward: a well‑defined reference diameter simplifies pass/fail routines and reduces interpretation time during first‑article inspections or random batch checks. Built for everyday workshop use and longevity Constructed from special steel, the component resists wear in high‑use environments while remaining simple to clean and store. The 50 mm overall length provides sufficient gripping area for manual handling and stable seating in fixtures, while the low mass (0.016 kg) minimises the risk of slippage during quick checks. The workshop specification balances robustness with the dimensional stability required for frequent in‑process inspection, extending service intervals and lowering the total cost of ownership through reduced rework. Integrates into inspection workflows and traceability systems The design supports efficient quality control processes: the compact measuring pin fits in benches, holders and customised gauges for rapid transfer of measured values into inspection reports. For inventory and procurement, note SKU M323.631 and GTIN 4061905059810 for unambiguous identification. Specifying a high‑precision measuring element of this class reduces scrap and downstream adjustments, helping maintain throughput and assuring customers of consistent component conformity. Choose Metav IndustryLine parts from Metav Werkzeuge for workshop‑ready precision and ask our consultants about tailored inspection solutions Technical data SKU: M323.631 GTIN: 4061905059810 Manufacturer: Metav IndustryLine Key measurements Nominal diameter: 6.31 mm Length: 50 mm Mass: 0.016 kg Tolerance: ±0.001 mm Features Material: special steel Single gauge / test pin design Workshop version suitable for frequent use FAQ What tolerance does the pin provide? The gauge pin M323.631 is manufactured to a tolerance of ±0.001 mm, making it suitable for tight end‑measure checks and precision fit verification. What material is the pin made from and how durable is it? This measuring pin is made from special steel and is supplied in a workshop specification intended for regular use; the material choice supports wear resistance and stable dimensional performance. Is a calibration certificate supplied with the item? The product data does not indicate a supplied calibration certificate; calibration status should be confirmed with Metav Werkzeuge if a certificate is required for quality records. Which applications are suitable for this gauge pin? The pin is intended for end‑measure checks, go/no‑go assessments and fixture‑mounted dimensional verification in machining, assembly and quality control operations. Can the pin be used with standard holders and measuring fixtures? Yes—the single‑pin design and standard nominal diameter allow integration into common holders and bespoke fixtures; refer to SKU M323.631 for compatible accessories. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.32mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of a compact, workshop‑grade reference pin that combines micrometre‑class accuracy and a stable 50 mm length for reliable end‑dimension checks; order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge Pin M323.632 — single test pin, 6.32 mm diameter, ±0.001 mm accuracy (Metav IndustryLine) The Gauge Pin M323.632 is a workshop‑grade reference pin for precise end‑dimension verification and fixture alignment in fine mechanical and small‑parts production Single gauge pin for precision checks Diameter 6.32 mm, tolerance ±0.001 mm Length 50 mm for stable referencing Workshop‑grade special steel construction Precision tailored to the micro range Classified for the Micro‑range, this reference pin delivers ±0.001 mm tolerance on a 6.32 mm diameter, providing the accuracy required for the smallest, most delicate parts. The sub‑millimetre tolerance makes the pin suitable for high‑precision end‑dimension checks where repeatability is essential; this converts measurement certainty into fewer reworks and faster process decisions. The compact format supports fine mechanical tasks while keeping handling and integration straightforward. Stable referencing for repeatable results With a 50 mm shank and a low mass of approximately 0.016 kg, the pin offers a combination of reach and dimensional stability that reduces measurement variation when used as a datum in fixtures or assembly jigs. The special steel construction has been chosen for dimensional integrity and wear resistance in workshop environments, ensuring consistent contact geometry over many cycles. The workshop‑grade execution supports routine in‑line checks without complex fixturing. Practical use in inspection and assembly Intended as a single, replaceable reference element, the test pin simplifies go/no‑go referencing, alignment checks and end‑dimension verification in small‑part manufacture. The controlled tolerance and compact form factor enable quick comparison tasks and integration into gauges or holding fixtures. For traceable inspection chains, the pin provides a stable physical reference that reduces measurement uncertainty and supports efficient quality control. The Metav IndustryLine pedigree signals a European quality filter behind the supply chain. For assured, repeatable end‑dimension control choose the Metav IndustryLine M323.632 — contact Metav Werkzeuge in Emmerich for tailored application advice at info@metav-werkzeuge.com or by phone for dispatch from our European quality hub Technical data Article number: M323.632 GTIN: 4061905059827 Category: Messstifte Facts Diameter: 6.32 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.016 kg Special features Material: special steel Workshop‑grade execution Single gauge pin (individual item) Application: end‑dimension checks FAQ What tolerance does this gauge pin provide? The M323.632 gauge pin provides a tolerance of ±0.001 mm, delivering micrometre‑class accuracy for precise end‑dimension checks. Is the pin suitable for fixture referencing in small parts production? Yes — the 50 mm length and compact diameter make this test pin suitable as a datum or reference in fixtures and assembly jigs for small parts. What material is the pin made from? The pin is manufactured from special steel designed for dimensional stability and wear resistance in workshop conditions. Can this single gauge pin be used for go/no‑go checks? Yes — the individual test pin functions as a stable physical reference for go/no‑go comparison and alignment tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.33mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Finish, Packed in Case - Metav IndustryLine
Combining ±0.001 mm accuracy with a compact 6.33 mm diameter and a 50 mm shaft delivers dependable end‑measurement performance for workshop inspection tasks; order directly via Metav Werkzeuge or consult our specialists for application advice. M323.633 gauge pin — inspection pin, 6.33 mm, ±0.001 mm tolerance The M323.633 gauge pin is a precision inspection pin engineered for reliable end‑measurements in workshop and metrology environments. Precision tolerance ±0.001 mm Diameter 6.33 mm, shaft length 50 mm Workshop version in special steel Supplied in transport case High‑precision control that reduces rework and inspection time The inspection pin is specified with a ±0.001 mm tolerance, which places it in the realm of high‑precision gauging for critical end measurements. Such repeatability reduces the need for secondary checks and shortens throughput time in quality control processes. The 6.33 mm diameter, paired with a 50 mm shaft, permits secure seating in pin fixtures and jigs while maintaining low thermal mass, so dimensional shifts due to handling are minimised. Specifying this probe in measurement plans supports traceable, reproducible results and a leaner inspection routine. Built for daily workshop use with robust materials and transport protection Manufactured in special steel and supplied as a workshop version, the pin balances corrosion resistance with wear characteristics that suit repetitive contact checks. Its compact mass and measured geometry make it easy to position in fixtures and to handle by operators without specialised tools. Delivery in a protective transport case prevents transit damage and preserves the datum surfaces ready for immediate use on the shop floor. This combination of material choice and protective packaging helps maintain accuracy across numerous inspection cycles. Simple integration into existing metrology workflows As a single inspection pin intended for end‑measurement tasks, the component sits readily within established gauging arrangements, plug fixtures and go/no‑go checking procedures. The M323.633 gauge pin complements calibrated master tools and can be adopted for both spot checks and systematic sampling in production runs, improving process control and reducing scrap. Documentation of physical dimensions and the compact form factor ease fixture design and spare‑part inventory planning, supporting efficient maintenance of measurement capability. For precision end‑measurements trust Metav IndustryLine's M323.633 gauge pin — contact Metav Werkzeuge for ordering and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.633 GTIN: 4061905059834 Manufacturer: Metav IndustryLine Facts Diameter: 6.33 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.016 kg Special features Material: Special steel Workshop version Supplied in transport case Single inspection pin for end measurements FAQ What tolerance does the pin provide? The M323.633 gauge pin is specified with a tolerance of ±0.001 mm for high‑precision end‑measurements. Which material is used for this inspection pin? The M323.633 is made from special steel, chosen for its durability in workshop inspection routines. How is the pin delivered? The inspection pin is supplied individually in a protective transport case to protect the measuring surfaces during transit. What inspection tasks suit this pin? The pin is intended for end‑measurement, fixture checking and plug‑gauge style inspections within quality control workflows. What are the pin's dimensions and mass? Diameter 6.33 mm, length 50 mm, weight approximately 0.016 kg; product reference M323.633 Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.34mm Gauge Pin, Single, ±0.001 mm, 50 mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of submicron tolerance, robust special steel and protective transit packaging for reproducible end‑dimension checks; order the gauge pin directly via Metav Werkzeuge or contact the consultants for application advice. M323.634 gauge pin — single 6.34 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) M323.634 gauge pin — single 6.34 mm, ±0.001 mm, 50 mm length is a precision reference pin for end‑dimension verification and fixture alignment in production and inspection environments High-precision tolerance ±0.001 mm Special steel for dimensional stability Supplied in protective transit case Stable reference for end‑dimension control The gauge pin provides a reliable reference for checking final dimensions and alignment of mating parts. With a diameter of 6.34 mm and a tight tolerance of ±0.001 mm, the pin serves as a high‑accuracy datum for Go/no‑Go testing, plug gauges or fixture set‑up. The compact 50 mm length reduces bending moments while maintaining sufficient engagement for most small to medium assemblies, making it suitable for toolrooms, quality control benches and assembly lines requiring repeatable end‑measurements. This precision level reduces rework and speeds up inspection cycles by supplying an unambiguous go/no‑go condition. Durable construction and handling benefits Manufactured from special steel, the pin resists wear and keeps its diameter stability even under frequent insertions, which extends service life and lowers lifetime cost. The workshop‑grade finish and the straightforward cylindrical geometry simplify cleaning and handling; the modest mass (approx. 0.016 kg) makes the pin easy to manoeuvre and store. The supplied protective case ensures safe transport and prevents nicks that would otherwise compromise accuracy, so the gauge remains ready for immediate use at the bench or in the fixture room. Integration into quality workflows and traceability The precision pin fits seamlessly into routine quality workflows as a tactile reference for end‑dimension verification and assembly checks. Identifiable by its SKU and GTIN, the component can be logged in inventory systems and traced across production batches. For customers seeking procedural certainty, the workshop version signals pragmatic robustness while preserving metrological performance for recurring use in calibration routines and process control documentation. For professional procurement or technical clarification, contact Metav Werkzeuge — Metav IndustryLine recommends this gauge pin for reliable end‑dimension checks in production and inspection setups Technical data Article number: M323.634 GTIN: 4061905059841 Material: Special steel Weight: 0.016 kg Length: 50 mm Tolerance: ±0.001 mm Core data Diameter: 6.34 mm Length: 50 mm Tolerance: ±0.001 mm Mass: 0.016 kg Messbereich max: 6.34 mm Special features Supplied in plastic/wooden case for transport Workshop execution Suitable for end‑dimension verification SKU: M323.634 FAQ What is the declared tolerance of this gauge pin? The gauge pin is manufactured to a tolerance of ±0.001 mm, guaranteeing tight dimensional control for end‑measure checks. Which material is used for the M323.634 gauge pin? The M323.634 gauge pin is made from special steel, selected for dimensional stability and wear resistance in routine inspection tasks. Is the gauge pin supplied ready for use and how is it protected in transit? The pin is delivered in a protective plastic or wooden case for transport, protecting the gauge pin from damage prior to use. For which applications is this single gauge pin suitable? This precision pin is intended for end‑dimension verification, fixture alignment and plug‑gauge comparisons in production and quality control environments. How can the M323.634 be recorded for traceability? The pin can be referenced by its SKU M323.634 and GTIN 4061905059841 for inventory and traceability systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.35mm Test Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of precise fit control and reproducible results thanks to the combination of a 6.35 mm nominal diameter, an ultra-fine ±0.001 mm tolerance and a 50 mm working length; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.635 — Precision gauge pin, 6.35 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge pin M323.635 is a workshop-grade precision pin designed for final diameter verification and go/no-go checks in production, inspection and assembly environments. Ultra-fine tolerance ±0.001 mm Nominal diameter 6.35 mm for standard bores Robust 50 mm length for secure engagement Workshop execution in special steel Fast, traceable diameter checks that save time on the line The gauge pin delivers repeatable pass/fail verification for bore diameters, enabling quicker in-process decisions and fewer scrapped parts. Manufactured from special steel and finished for tight form tolerances, the test pin provides a stable reference that reduces inspection time compared with labour-intensive measuring setups. The very fine ±0.001 mm tolerance makes the pin suitable where end-dimension control is critical; this level of conformity reduces rework and supports consistent assembly quality across batches. The compact design permits rapid handling at inspection stations and straightforward storage with other precision references. Durable construction for frequent workshop use Built as a workshop execution item, this plug-style test pin is intended for repeated insertion cycles and routine quality checks. The 50 mm length gives secure engagement depth while retaining low mass (approx. 0.016 kg) for easy handling. Surface finish and material choice are selected to sustain dimensional stability under normal workshop conditions; the result is a measuring aid that resists wear and preserves its nominal diameter over many cycles. Using a hardened, corrosion-resistant steel alloy extends service life and helps maintain measurement integrity between calibrations. Simple integration into inspection routines and tooling sets Designed as an end-mass verification tool, the gauge pin fits naturally into assembly jigs, inspection trays and gauge sets. Its 6.35 mm size corresponds to common bore standards, so it can be used as a go/no-go reference or as a master for quick visual or tactile control. The compact format reduces fixture modification and the pin can be combined with other sized pins to create an arranged reference set. Clear labelling (SKU M323.635, GTIN available) aids inventory management and traceability within quality documentation. Request stock and technical availability from Metav Werkzeuge in Emmerich or ask for a detailed specification sheet for the Metav IndustryLine gauge pin to ensure fit with existing inspection procedures Technical data Article number: M323.635 GTIN: 4061905059858 Category: Messstifte Facts Nominal diameter: 6.35 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.016 kg Material: Special steel Special features Workshop execution Designed for end-dimension checks Robust finish for repeated use Suitable for go/no-go verification FAQ What tolerances does the gauge pin offer? The gauge pin is manufactured with a tolerance of ±0.001 mm, providing ultra-fine conformity for final-dimension checks. Is the pin suitable for repeated in-line use in production? Yes; the plug-style pin in special steel is specified for workshop execution and supports frequent insertion cycles without rapid wear. Which nominal diameter and length are supplied for the SKU M323.635? The item M323.635 is supplied as a 6.35 mm nominal diameter pin with a 50 mm working length. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.36mm Test Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine ±0.001 mm accuracy, compact 50 mm length and robust special steel construction for reliable end‑measurement and reduced rework in everyday workshop inspection. Order the gauge pin directly via Metav Werkzeuge or consult the team for application support. Gauge pin M323.636 — single precision pin, Ø 6.36 mm, ±0.001 mm (Metav IndustryLine) The Gauge pin M323.636 is a single, precision ground pin designed for end‑measurement and quick go/no‑go inspection tasks in workshop and production quality control. Workshop version for robust everyday use Diameter Ø 6.36 mm with ±0.001 mm tolerance Length 50 mm for compact inspection tasks Precision ground from special steel Consistent micrometric accuracy that cuts rejects The gauge pin delivers a ±0.001 mm tolerance, a level of precision that supports fine end‑measurements and repeatable pass/fail checks. Such micrometric accuracy reduces uncertainty in inspection steps and helps to identify deviations before parts proceed to assembly. The tight tolerance translates into repeatability across measurement cycles, which is particularly valuable for short, critical runs or spot checks where a stable reference dimension avoids time‑consuming rework. Built for daily workshop handling and durability Manufactured from special steel and offered in a workshop specification, this precision pin resists routine wear while maintaining measurement integrity. The compact design minimises flex and handling error during insertion into bores or when used as a reference plug. As a result, the component stays serviceable for longer under typical workshop stresses, supporting a dependable inspection workflow and lowering lifecycle disruption from replacements. Compact size for fast, practical inspections With a nominal diameter of 6.36 mm and a length of 50 mm, the pin is tailored for quick verification of small bores and end dimensions. Its compact footprint enables fast positioning and straightforward use in fixtures or handheld checks, speeding up quality control without sacrificing accuracy. This makes the component suitable for final checks, setup verification and routine sampling where swift, trustworthy inspection data is required. Contact Metav Werkzeuge today to enquire about the M323.636 gauge pin, discuss integration into inspection routines or request application advice from the Metav team in Emmerich. Technical data Article number: M323.636 GTIN: 4061905060670 Manufacturer: Metav IndustryLine Facts Diameter: 6.36 mm Length: 50 mm Accuracy: ±0.001 mm Weight: 0.016 kg Special features Material: Special steel Workshop specification Single precision gauge pin for end measurement FAQ What tolerance does this gauge pin offer? The gauge pin M323.636 provides an accuracy of ±0.001 mm, suitable for micrometric end‑measurement tasks. What material is used for the pin? This precision pin is made from special steel, selected for dimensional stability and resistance to everyday workshop wear. What applications suit this pin? The pin is intended for end‑measurement and quick go/no‑go inspections in workshop and production quality control environments. Is the diameter and length suitable for bore checks? Yes. With a nominal Ø 6.36 mm and 50 mm length, the pin is well suited to verify small bores and serve as a reference for short inspection tasks. Is this item supplied as a single unit or part of a set? This listing describes a single precision gauge pin (SKU M323.636); multiple items can be combined to form a set where required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.37mm Gauge Pin Single ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Reliable workshop verification with ±0.001 mm tolerance and a 6.37 mm nominal diameter in a compact 50 mm length, enabling repeatable fit checks and minimal rework. Benefit from the robust special‑steel construction and fast procurement through Metav Werkzeuge for steady inspection throughput. Gauge Pin M323.637 — 6.37 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The Gauge Pin M323.637 is a workshop‑grade cylindrical verification pin designed for precise end‑measure and plug checks in production and inspection processes. ±0.001 mm measurement accuracy 6.37 mm nominal diameter 50 mm shaft length Workshop‑grade special steel construction Ensure repeatable fit and reduce production variance The high‑precision ±0.001 mm tolerance of this verification pin supports consistent fit verification across serial production. Such narrow tolerance limits make the pin suitable for final go/no‑go checks and comparative gauging where small dimensional shifts can lead to assembly issues or increased rejects. By using a dedicated cylindrical reference with a defined nominal diameter of 6.37 mm, inspection routines gain clarity: deviations are traceable and corrective actions can be applied promptly, improving overall quality assurance and reducing scrap rates. Robust, compact design for daily workshop use Constructed from special steel and specified as a workshop‑grade tool, the pin offers a balance of wear resistance and handling convenience. The 50 mm shaft length provides sufficient contact area for stable insertion while keeping the tool compact for fixture use and handheld checks. At approximately 0.016 kg, the component is easy to position without causing undue operator fatigue, and the solid construction minimises bending or surface damage during routine use, prolonging service life and maintaining dimensional reliability. Integrates simply into inspection and tooling setups As a single verification pin, this product is intended for targeted end‑measure checks, plug gauging and reference testing in fixtures and jigs. The straightforward geometry—cylindrical with a nominal 6.37 mm diameter—allows easy pairing with hardened bushings, fixture housings or comparison blocks. Traceable identification via the SKU and GTIN supports stockkeeping and audit trails, while the clear specification of accuracy helps to select the right reference part for tolerance stacks and assembly trials. This pragmatic approach reduces setup time and supports efficient throughput in quality control stations. For application guidance or to obtain the Metav IndustryLine gauge pin M323.637 for precision fit‑up and inspection tasks, contact Metav Werkzeuge in Emmerich for prompt technical advice and ordering information Technical Data Article number: M323.637 GTIN: 4061905060687 Weight: 0.016 kg Material: Special steel Length: 50 mm Diameter: 6.37 mm Accuracy: ±0.001 mm Label: Prüfstift, einzeln, 6,37mm, +/- 0.001 mm Länge 50 mm Facts Length: 50 mm Diameter: 6.37 mm Tolerance: ±0.001 mm Weight: 0.016 kg GTIN: 4061905060687 Special features Workshop‑grade execution Single test pin Compact cylindrical geometry Intended for end‑measure and plug checks FAQ What tolerance does this gauge pin provide? The gauge pin M323.637 is specified with a tolerance of ±0.001 mm, making it suitable for high‑precision verification tasks. What is the nominal size and length of the pin? The pin has a nominal diameter of 6.37 mm and a shaft length of 50 mm, designed for straightforward insertion into fixtures and housings. Is this supplied as an individual test pin? Yes, the item is delivered as a single verification pin intended for targeted plug and end‑measure checks. Which applications benefit most from this pin? Assembly verification, plug gauging and final fit checks in production and inspection routines benefit from the dimensional stability and high tolerance of this verification pin. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.38mm Test Pin, Single, ±0.001 mm, 50 mm Length, Workshop Version - Metav IndustryLine
Take advantage of ±0.001 mm accuracy together with a 6.38 mm diameter and a sturdy special steel construction for reproducible reference measurements; ideal for precision checking and plug‑gauge applications. Order the gauge pin directly via Metav Werkzeuge or contact the consultants for application advice. Gauge pin M323.638 — Single 6.38 mm, ±0.001 mm, Metav IndustryLine workshop edition The gauge pin M323.638 is a single, high‑precision reference pin designed for dimensional checking, assembly control and go/no‑go verifications in workshop and production environments. 6.38 mm precision diameter ±0.001 mm measurement tolerance 50 mm hardened length for stability Workshop edition in special steel Precision that reduces rework and inspection time A tolerance of ±0.001 mm places this reference pin in the high‑precision category used where micrometre accuracy matters. The extremely fine tolerance reduces uncertainty in pass/fail checks and supports faster decision cycles on the shop floor. With a compact 50 mm length and slim 6.38 mm diameter, the pin serves as a reliable reference for bore testing, fixture set‑up and repeatable gauging tasks, enabling quality teams to maintain throughput without rework. Robust material for consistent contact behaviour Manufactured from special steel, the pin combines surface hardness with dimensional stability, which keeps contact geometries consistent across repeated use. The chosen steel lowers the risk of wear‑induced measurement drift and preserves the effective gauge diameter under normal workshop loading. As a result, maintenance intervals can be extended and tool‑change downtime reduced, which supports overall equipment efficiency. Workshop design tailored to practical use The workshop edition focuses on ease of handling and durability in everyday production conditions. The 50 mm length provides good engagement depth while remaining manoeuvrable in tight assemblies; the compact format suits bench testing and fixture checks alike. Together with the high tolerance, this design supports quick, reproducible checks that feed directly into manufacturing control processes and SPC records. Clear evidence for quality assurance and traceability The compact reference pin is suitable for integration into incoming inspection routines and final checks where a clearly defined reference is required. Its specification—6.38 mm diameter, 50 mm length and ±0.001 mm tolerance—allows straightforward documentation in inspection protocols and parts lists. Using defined mechanical references like this pin contributes to demonstrable process control and reduces ambiguity during audits or supplier assessments. For precision work choose Metav IndustryLine components — contact Metav Werkzeuge for tailored advice and reliable delivery from Emmerich. Technical data Article number: M323.638 GTIN: 4061905060694 Manufacturer: Metav IndustryLine Facts Diameter: 6.38 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.016 kg Special features Workshop edition Material: special steel Single gauge pin FAQ What applications is this gauge pin suitable for? This gauge pin M323.638 is suitable for bore checks, fixture set‑up, reference gauging and go/no‑go verifications in workshop and production inspections. Is the tolerance of ±0.001 mm sufficient for tool setting? Yes, the ±0.001 mm tolerance of the pin supports high‑precision tool setting and verification where micrometre‑level accuracy is required. Which material is used and how does it affect wear? The pin is made from special steel; this provides improved surface hardness and dimensional stability to reduce wear over repeated use. Can this pin be used as a production reference in a quality system? The specification of the pin (6.38 mm, 50 mm, ±0.001 mm) makes it suitable as a documented reference tool within a quality system for repeatable measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.39mm Gauge Pin Single ±0.001mm Accuracy Length 50mm Workshop Finish - Metav IndustryLine
Take advantage of absolute dimensional certainty and robust workshop construction for consistent end‑measurement checks; the compact 6.39 mm diameter and ±0.001 mm tolerance ensure fast, reproducible decisions on the shop floor. Order directly via Metav Werkzeuge or consult their technical team for supply and batch planning. Gauge pin, single 6.39 mm ±0.001 mm, 50 mm – Metav IndustryLine The gauge pin, single 6.39 mm ±0.001 mm, 50 mm is a workshop‑grade inspection pin designed for precise end‑dimension verification and routine quality control of small bores and mating parts. Workshop‑grade construction Diameter 6.39 mm ±0.001 Length 50 mm for deeper checks Supplied in transport case Reproducible precision for end‑dimension checks The compact inspection mandrel provides ±0.001 mm repeatability, giving a reliable reference for go/no‑go decisions during final inspections. This level of control reduces ambiguity in acceptance criteria and lowers the risk of downstream rework. The narrow 6.39 mm diameter is optimised for small‑bore verification and end‑mass checks, enabling quick tactile confirmation where measuring equipment access is limited. Such a tool supports consistent quality control routines without adding complex measuring procedures. Robust workshop design that endures daily use Constructed from special steel and manufactured as a workshop‑grade item, the pin tolerates regular handling and resists premature wear. The 50 mm overall length reaches further into bores and confirms interfacing surfaces that shorter pins cannot. Supplied in a protective transport case, the component arrives ready for production use and is protected during storage and transport, preserving the calibrated surface finish and reducing the frequency of replacement. Streamlined inspection for faster throughput As a compact and simple inspection aid, this pin shortens inspection cycles and integrates smoothly into existing workflows on the production line. Its low mass and ergonomic proportions allow rapid manual checks, while the precise diameter and tight tolerance support dependable pass/fail judgements. Using such a standardised reference helps maintain traceable dimensional control across batches and speeds up decision‑making in assembly or incoming inspection processes. For supply and application advice relating to this Metav IndustryLine gauge pin (SKU M323.639), contact Metav Werkzeuge in Emmerich for delivery options and availability: info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.639 GTIN: 4061905060700 Brand: Metav IndustryLine Facts Diameter: 6.39 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.016 kg Special features Material: special steel Workshop‑grade execution Supplied in protective transport case FAQ What is the typical application for this gauge pin? The gauge pin is intended for end‑dimension verification, bore checking and quick go/no‑go inspection tasks on small components and mating parts. Is the diameter specification suitable for precision assembly checks? Yes, the 6.39 mm diameter with a ±0.001 mm tolerance provides a tight reference suitable for precise assembly and final inspection operations. How does the workshop execution affect durability? The workshop‑grade construction and chosen special steel increase resistance to wear during frequent handling and routine inspection use. Does the product come protected for transport? The pin is supplied in a protective transport case to safeguard the measuring surface during shipping and storage. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.3mm Gauge Pin, Single, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of a combination of ultra‑fine tolerance, robust special steel construction and compact 50 mm length to ensure repeatable end‑measurements in the workshop. The small form factor and precise ±0.001 mm accuracy reduce setup time and measurement uncertainty; order the gauging pin directly via Metav Werkzeuge or consult our specialists for procurement advice. Gauging pin M323.630 — Single 6.30 mm test pin, ±0.001 mm accuracy (Metav IndustryLine) The Gauging pin M323.630 is a precision test pin for end‑measurement and dimensional inspection, designed for workshop and inspection‑bench applications. Workshop execution for daily use Diameter 6.30 mm with ±0.001 mm tolerance 50 mm length for end‑measurement tasks Delivered in transport box for secure handling Repeatable precision for end‑measurements High repeatability is the central benefit of this test pin. With a declared tolerance of ±0.001 mm, the component serves as a reference for tight dimensional checks and end‑measurements where small deviations matter. The nominal 6.30 mm diameter provides a stable contact area that limits deflection and contact ambiguity; used in go/no‑go fixtures or as a reference in comparative checks, the pin helps to reduce measurement scatter and supports reliable pass/fail decisions in production control. Such precision is particularly beneficial when assessing final dimensions and when interchangeability of parts is required. Durable workshop design reduces downtime Built in a workshop configuration from special steel, the pin balances wear resistance with machinability. The compact 50 mm length and low mass make handling straightforward while remaining stiff enough for repeatable contact in common inspection setups. The robust finish resists abrasion during repeated placements and the item is supplied as a single unit in a protective transport box, which simplifies storage and prevents accidental damage during transit. These attributes together reduce rework and downtime caused by damaged or uncertain measuring references. Seamless fit into inspection workflows The test pin integrates easily into standard workshop routines: it functions as a handheld reference, a fixture insert or part of a pin‑stack in gauging arrangements. Lightweight construction aids fast placement while the precision tolerance ensures that the same reference can be used across several stations for consistent results. Traceability is aided by clear labelling and the included identifiers; the format supports rapid inventorying and straightforward replacement cycles, maintaining measurement integrity across production batches without complex calibration procedures on site. Contact Metav Werkzeuge for tailored procurement of the M323.630 gauging pin — Metav Werkzeuge GmbH in Emmerich offers expert advice and reliable supply: info@metav-werkzeuge.com, +49 2822 7131930 Technical Data Article number: M323.630 GTIN: 4061905059803 Brand: Metav IndustryLine Item: Single test pin Facts Diameter: 6.30 mm Length: 50 mm Declared tolerance: ±0.001 mm Weight: 0.016 kg Special features Material: Special steel Workshop execution Delivered in a protective transport box Intended use: end measurements FAQ What is the M323.630 suitable for? The M323.630 gauging pin is suitable for end‑measurement, dimensional verification and use in go/no‑go fixtures on the inspection bench. What accuracy does the pin offer? The M323.630 is specified with a declared accuracy of ±0.001 mm, making it suitable for fine tolerance checks. Which material is the test pin made from? The M323.630 is manufactured from special steel in a workshop finish designed for repeated handling. How is the item delivered? The M323.630 is supplied as a single pin in a protective transport box to safeguard the reference surface during storage and transit. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.41mm Gauge Pin ±0.001mm Length 50mm Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, micrometre-level tolerance and robust workshop finish for reliable end-dimension checks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. Gauge pin M323.641 — 6.41 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The gauge pin M323.641 is a workshop-grade precision plug used for end-dimension verification and go/no-go fitting tasks in production and inspection environments. Diameter 6.41 mm with ±0.001 mm tolerance Length 50 mm for stable probing and handling Manufactured from special steel for durability Workshop version for consistent fit and finish High-precision control for repeatable checks Engineered for repeatable end-dimension verification, this gauge pin delivers a nominal diameter of 6.41 mm with a certified tolerance of ±0.001 mm, enabling micrometre-class discrimination in tight fits. The narrow tolerance supports objective Go/No-Go assessments and reduces uncertainty during fit checks, which is particularly relevant in small-batch production and incoming inspection. Where traceable repeatability matters, the defined size and minimal runout translate directly into fewer false rejections and steadier process control, supporting leaner quality routines. Robust material and workshop finish for longevity Made from special steel with a workshop-grade finish, the probe resists wear in repetitive insertion tasks and retains its diameter tolerance over time. The 50 mm length offers a comfortable working grip and sufficient engagement depth for common fixtures and bores without excessive overhang, improving handling and reducing deflection. At an item weight of 0.016 kg the component is easy to position manually while remaining stiff enough for accurate seating. The combination of material choice and finish reduces surface damage to mating parts and extends in-service life, lowering replacement frequency and total operating cost. Practical integration into quality workflows Designed for seamless use in inspection benches and assembly jigs, the pin is suitable for end-dimension checks during final inspection, tooling set‑up and first-article verification. The compact form factor and strict tolerance make it an efficient tool for standardised measurement routines and sampling plans. Marked for traceability with SKU M323.641 and GTIN data, the item can be logged into asset lists or inventory systems to support calibration intervals and quality documentation. Employing such standardised reference sizes helps stabilise statistical process control (SPC) inputs and simplifies audit trails. For reliable end-dimension verification rely on Metav IndustryLine's precision gauge pin — contact Metav Werkzeuge for procurement advice and technical clarification at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.641 GTIN: 4061905060724 Brand: Metav IndustryLine Facts Diameter: 6.41 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.016 kg Special features Material: special steel Workshop version for consistent fit and finish Suitable for end-dimension verification and Go/No-Go checks FAQ What is the primary use of this gauge pin? The gauge pin M323.641 is intended for end-dimension checks and fit verification in production and inspection routines. Is the tolerance suitable for precision assembly tasks? Yes, the ±0.001 mm tolerance provides micrometre-level control appropriate for high-precision assembly and quality checks. Can the pin be used for penetrating small bores and seats? The 6.41 mm diameter and 50 mm length make the pin well suited to engage common small bores and seating surfaces for fit tests. What material is the pin made from and why does it matter? Manufactured from special steel, the pin offers improved wear resistance and dimensional stability under repeated use. How is the item identified for stock and traceability? Identification is possible via SKU M323.641 and GTIN 4061905060724 for inventory and calibration records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.42mm Gauge Pin ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop‑grade durability, submicron accuracy and compact handling for reliable end‑dimension inspection in production and quality control. Order the M323.642 gauge pin directly via Metav Werkzeuge or consult our experts for application guidance. M323.642 Gauge Pin — 6.42 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.642 gauge pin is a workshop‑grade inspection pin designed for precise end‑dimension checks and fixture verification in metalworking and assembly environments. Workshop-grade inspection pin, 50 mm length Diameter 6.42 mm with ±0.001 mm accuracy Hardened special steel for wear resistance Supplied in protective transport case Consistent submicron accuracy for end‑dimension inspection The compact gauge pin delivers an exceptional ±0.001 mm tolerance, making it suitable where reproducible end‑dimension verification is critical. This level of accuracy reduces uncertainty during go/no‑go checks and finish inspections, which in turn supports consistent production quality. The 6.42 mm diameter combined with a 50 mm datum length simplifies short‑span checks while preserving measurement repeatability in handheld or fixture situations. Robust workshop construction that endures daily use Built in a workshop‑grade design from special steel, the pin resists wear and maintains form under frequent engagement. The choice of material provides reliable surface hardness and dimensional stability, reducing the need for frequent replacement. Supplied in a protective transport case, the unit arrives ready for safe storage and on‑site handling, protecting the precision ground surfaces during transit and daily rotation. Compact handling and practical application benefits The small footprint of this inspection pin suits inspection of small components and hard‑to‑reach bores, and its moderate length balances accessibility with rigidity. Classified for fine mechanical and workshop tasks, the pin functions well in fixture alignment, plug gauge sets and assembly jigs where clear, repeatable reference points are required. For teams integrating these pins into measurement routines, Metav’s product range offers complementary items that streamline workflow and reduce measurement error. For an exact match to inspection requirements or to discuss larger quantities and delivery options, contact Metav Werkzeuge to arrange a technical consultation on the M323.642 gauge pin and related metrology equipment. Technical data SKU: M323.642 GTIN: 4061905061080 Label: Prüfstift, einzeln, 6,42mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 6.42 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.016 kg Special features Material: Special steel Workshop version Supplied in transport case High‑precision inspection pin for end‑dimension checks FAQ What tolerance does this inspection pin offer? The M323.642 gauge pin is specified at ±0.001 mm, providing submicron accuracy for precise end‑dimension verification. Is this pin suitable for workshop use and frequent handling? Yes, the workshop‑grade construction and special steel material make the pin robust for daily use in production and inspection environments. Does the pin come with protective packaging for transport? The inspection pin is supplied in a protective transport case to safeguard the ground surfaces during delivery and storage. For which applications is a 6.42 mm gauge pin most appropriate? A 6.42 mm diameter and 50 mm length are ideal for end‑dimension checks, fixture alignment and small‑component inspections where compact, repeatable reference points are required. Can this pin be integrated into existing gauge sets or fixtures? The M323.642 inspection pin is designed for straightforward integration into plug gauge sets, alignment fixtures and assembly jigs to improve measurement repeatability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.43mm Gauge Pin, Workshop Version, Length 50mm, ±0.001mm - Metav IndustryLine
Combine workshop-grade durability with a ±0.001 mm tolerance and a compact 6.43 mm diameter to secure repeatable end‑measurements and reliable fit checks. Order the gauge pin directly via Metav Werkzeuge or consult their advisors for application-specific recommendations. Gauge pin, single, 6.43 mm, ±0.001 mm, 50 mm (Metav IndustryLine) The Gauge pin, single, 6.43 mm, ±0.001 mm, 50 mm is a workshop‑grade pin gauge designed for precise end‑measurement, fit verification and assembly inspection in production and quality control environments. Extremely tight tolerance ±0.001 mm Diameter 6.43 mm, compact form 50 mm overall length for fixture checks Workshop‑grade special steel, boxed for transport High-precision fit for consistent inspection results The compact cylindrical gauge delivers a repeatable reference thanks to its ±0.001 mm specification and accurately machined 6.43 mm diameter. Such a narrow tolerance reduces uncertainty in go/no‑go and fit checks, so pass/fail decisions become faster and less ambiguous. This high level of precision supports process control in assembly lines and during final inspection, where a reliable reference standard shortens decision loops and reduces rework. Robust workshop design that copes with daily use Manufactured as a workshop‑grade item from special steel, the pin provides mechanical stability for routine handling and insertion tasks. Its 50 mm length balances reach and stiffness, making it suitable for checking bores and alignment points without excessive deflection. The small mass (approx. 0.016 kg) eases manual handling and reduces wear on fixtures. Delivery in a transport box ensures the gauge arrives protected and ready for immediate use on the shop floor. Practical advantages for inspection workflows Integration into inspection jigs and gauges is straightforward: the compact geometry simplifies fixture design and the precise diameter serves as a repeatable datum for comparative checks. The combination of tight tolerance and workshop durability supports efficient sampling plans and rapid in‑process verification, which in turn helps maintain production uptime. Additionally, the clear specification facilitates documentation in quality records and supports traceable measurement routines. For application advice or to secure this Metav IndustryLine gauge pin for workshop inspection tasks, contact Metav Werkzeuge in Emmerich for tailored recommendations and reliable European supply Technical data Article number: M323.643 GTIN: 4061905061783 Brand: Metav IndustryLine Material: Special steel Weight: 0.016 kg Length: 50 mm Diameter: 6.43 mm Tolerance: ±0.001 mm Workshop execution Core numerical data Diameter: 6.43 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.016 kg Special features and versions Workshop‑grade design Delivered in a plastic or wooden box for transport ECLASS: 21170231 SKU: M323.643 FAQ What tolerance does the gauge provide? The gauge pin M323.643 is specified to ±0.001 mm, providing a very tight tolerance suitable for fine acceptance checks and precision fit verification. For which inspection tasks is this pin most suitable? Its compact diameter and length make the pin ideal for end‑measurements, bore checks and quick assembly fit checks in workshop and production environments. What material is the pin made from? The pin is manufactured from special steel, supplied as a workshop‑grade item to withstand routine handling and insertion operations. Is the gauge supplied protected for transport? Yes. Delivery includes a plastic or wooden box for transport, ensuring the pin is protected during shipment and ready for immediate use upon arrival. What are the product identifiers for ordering? Reference the Metav IndustryLine gauge pin by SKU M323.643 and GTIN 4061905061783 when specifying or ordering. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com