Precise pin gauges for reliable bore and tolerance checking
Pin gauges are tactile, high-precision gauges used for exact bore, internal thread and radius inspection, offering straightforward go/no-go verification and process-secure dimensional control in toolmaking and quality assurance. Made from hardened gauge steel, wear-resistant ceramic or carbide and finely lapped for superb surface finish, these gauges deliver micrometre-level accuracy and long service life while eliminating electronic error sources. Available as individual pins or complete sets in wooden cases, they support tasks such as measuring bore spacing, checking tapers and setting reference sizes for indirect measuring devices and come in strict tolerance classes compliant with industrial standards.
5–6mm Precision Gauge Pin Set 70mm Length 0.01mm Steps Plastic Case - Metav IndustryLine
Take advantage of high incremental resolution and robust construction for reliable bore checking in production and inspection. The combination of 0.01 mm graduation, special steel construction and a 70 mm working length supports reproducible measurements and efficient quality control. Order via Metav Werkzeuge or consult the on-site experts for specification matching. Gauge pin set M318.855 — Metrology gauge pins, 5.00–6.00 mm, 0.01 mm graduation (Metav IndustryLine) A gauge pin set M318.855 designed for precise plug-gauge checks and step-wise bore verification in workshop inspection and quality control. High precision 0.01 mm steps Range 5.00–6.00 mm in fine increments 70 mm working length for deeper bores Delivered in a protective transport case Consistent dimensional control for small bores The set delivers high repeatability through a fine 0.01 mm graduation across the 5.00–6.00 mm range, making it ideal for routine acceptance testing and in-line inspections where small tolerances matter. Gauge pins are used to verify hole diameters and fit; the incremental spacing reduces the need for interpolation and speeds up decision-making on the shop floor. The calibrated increments provide a clear, measurable basis to document conformance and to compare against drawings or inspection plans. Robust build and practical ergonomics for workshop use Manufactured from special steel and finished for wear resistance, the pins are dimensionally stable under normal workshop conditions and resist deformation during repeated use. The 70 mm length allows access into moderately deep bores and fixturing without compromising handling. Delivery in a protective transport case secures the set during storage and transit, reducing the risk of damage that would otherwise affect measurement reliability. The overall design supports rapid exchange between sizes, shortening inspection cycles and improving throughput. Fit for industrial metrology and routine quality checks This set is a practical solution for dimensional verification tasks in general metrology and production control. Its fine gradation and sturdy material suit small component inspection, jigs and fixtures checks, and assembly tolerance audits. Combined with Metav IndustryLine’s logistics and stock depth, the set is positioned as a dependable tool for workshops and quality departments seeking consistent plug-gauge performance without unnecessary complexity. Secure production-grade plug-gauge accuracy with Metav IndustryLine — contact Metav Werkzeuge for tailored advice and fast delivery from Emmerich, email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M318.855 GTIN: 4054469182070 SKU: M318.855 Weight: 2.91 kg Core specifications Measuring range: 5.00–6.00 mm Graduation: 0.01 mm Length (working): 70 mm Materials & features Material: Special steel Set: delivered as a set Case: included (protective transport box) Category: Gauges / Lehren FAQ What tolerance precision can be expected from this gauge pin set? The gauge pin set M318.855 provides fine 0.01 mm increments suitable for close tolerance checks and routine bore verification tasks. Can the pins be used for medium-depth bores and fixtures? Yes, the 70 mm working length allows access into deeper bores and many fixture arrangements, supporting practical workshop measurement. Is the material suitable for repeated industrial use? The pins are made from special steel and finished for wear resistance, which supports repeated use in production environments without rapid degradation. Does the delivery include a case for storage and transport? Delivery includes a protective transport case to keep the pins organised and safe during storage and transit. Which applications suit this gauge pin set best? Typical applications are plug-gauge checks, bore verification, fixture and jig set-up, and routine quality inspections in machining and assembly contexts. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5–6mm Probe Holder For Go/No-Go Pins, Red Aluminium Mount - Metav IndustryLine
Take advantage of the combination of anodised aluminium construction, a precise 5–6 mm pin fit and a compact, single-sided design for reliable gauge assembly and straightforward workshop integration — order directly via Metav Werkzeuge or consult our specialists for application advice. Measuring-pin holder NOGO, 5–6 mm — red single-sided mount (Metav IndustryLine) The Measuring-pin holder NOGO 5–6 mm is a compact, anodised aluminium mount designed to accept and secure 5–6 mm measuring pins for jigs, gauges and fixture assemblies in production and inspection environments. Anodised aluminium body for corrosion resistance Compatible with 5–6 mm measuring pins Single-sided red mounting for visual identification Secure retention with lightweight construction The holder delivers a secure fit for standard 5–6 mm measuring pins while keeping added mass to a minimum. Manufactured from anodised aluminium, the component resists corrosion and reduces wear on mating pins, which supports reproducible measurements over time. Its compact geometry (approx. 55 mm long, 12 mm wide) makes it suitable for close‑tolerance gauge blocks or modular fixture plates where space and stiffness must be balanced. The red single‑sided mount gives quick visual identification on populated fixtures, aiding rapid assembly and inspection workflows. Practical handling and straightforward integration Designed for workshop and metrology applications, this mount simplifies pin replacement and fixture modification. The one‑sided interface allows easy access for insertion and removal of pins, while the lightweight alloy minimises effects on dynamic assemblies. The product is intended for mechanical retention of measuring pins and can be integrated into custom jigs or portable gauges without altering core measurement procedures. The clear material choice and geometry reduce the need for frequent maintenance, offering a pragmatic solution for routine production and quality checks. Consistent quality backed by an experienced partner As part of the Metav IndustryLine range, the holder benefits from a supplier network focused on dependable supply and consolidated product expertise. Metav’s approach to democratising precision means components like this are offered with clear specification and predictable availability, supporting procurement and production planning. For purchasers seeking to standardise on modular gauge components, this mount represents a practical, low‑complexity element that contributes to overall measurement reliability and efficient workshop organisation. Contact Metav Werkzeuge for application support and reliable supply of Metav IndustryLine components; our consultants in Emmerich are available at info@metav-werkzeuge.com or +49 2822 7131930 to assist with technical queries and order coordination Technical data SKU: M318.567.6 Designation: Measuring-pin holder NOGO 5–6 mm, red single-sided mount Brand: Metav IndustryLine Facts Length: 55 mm Width: 12 mm Compatible pin diameter: 5–6 mm Special features Material: anodised aluminium Colour: red Single-sided mount for easy pin access For uptake of measuring pins (accepts standard 5–6 mm pins) Intended for jig, gauge and fixture assemblies FAQ Which pin diameters are compatible with this holder? The measuring-pin holder is specified for 5–6 mm pins and is designed to accept standard measuring pins within that diameter range; see SKU M318.567.6 for reference. Is the mount suitable for use in a corrosion-prone environment? Yes — the holder is manufactured from anodised aluminium, which improves surface durability and corrosion resistance compared with untreated alloy. Can the holder be fitted on both sides of a plate? The product is a single-sided mount, intended for one-sided insertion and access; the red mount provides visual identification when integrated into fixtures. Does the mount come as part of a kit or single item? This entry describes the individual Measuring-pin holder NOGO 5–6 mm (Metav IndustryLine, SKU M318.567.6); availability of kits or sets depends on the specific offering from Metav Werkzeuge. Is the component recommended for portable gauges and jigs? Yes — the compact dimensions (55 mm × 12 mm) and lightweight anodised construction make it suitable for portable gauges, jigs and modular fixture assemblies. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
5–6mm Test Pin Holder Double-Sided Green/Red - Metav IndustryLine
Taking advantage of a compact, colour‑coded design and anodised aluminium construction ensures rapid visual checks and durable handling during routine inspections; the double‑sided GO/NO‑GO functionality for 5–6 mm measuring pins speeds up go/no‑go decisions and reduces throughput time. Order the holder directly via Metav Werkzeuge or consult the Metav advisers for application guidance. Measuring Pin Holder GO/NO-GO, double-sided, 5–6 mm — Metav IndustryLine A Measuring Pin Holder GO/NO‑GO, double‑sided 5–6 mm designed for quick visual inspection and secure retention of measuring pins in workshop and inspection jigs. Double-sided GO/NO-GO configuration For measuring pins 5–6 mm Anodised aluminium construction Colour-coded green and red for quick checks Rapid, unambiguous GO/NO‑GO inspection for routine checks The double‑faced GO/NO‑GO layout provides immediate pass/fail feedback without supplementary gauges. Fitted for 5–6 mm measuring pins, the holder enables a swift transfer of inspection decisions from bench to process control, reducing handling time and minimising interpretation errors. Colour contrast between green and red supports fast visual sorting in production lines and quality stations, ensuring a more efficient verification routine. Durable, lightweight design that suits regular workshop use Constructed from anodised aluminium, the holder offers a resilient surface finish with increased corrosion resistance while keeping mass low for ease of handling. With an overall length of 80 mm and a width of 12 mm, the item balances compactness and operability: it is long enough to accommodate stable pin seating yet short enough for hand‑held use in tight workstations. The robust material choice delivers longevity under everyday workshop conditions. Practical compatibility and straightforward mounting options Designed specifically for the reception of measuring pins, the holder accepts pins with diameters of 5–6 mm, making it compatible with common pin assortments used in dimensional checks and fixture setups. The reception geometry secures pins for inside, outside or stepped reference checks when used in conjunction with go/no‑go procedures. The component is suitable as a modular element in inspection jigs or a simple portable check tool for fast verification tasks. Efficiency and traceability in the inspection workflow Labelling with the item code M318.568.6 supports traceability within inventory and quality documentation. The concise form factor simplifies integration into existing inspection kits or tool trolleys, promoting orderly handling and faster line-side decisions. By combining colour-coding, a metal finish that resists wear, and dedicated pin compatibility, the holder contributes to a predictable, repeatable inspection step that aligns with shopfloor demands. For dependable GO/NO‑GO checks choose the Metav IndustryLine measuring pin holder and contact Metav Werkzeuge for product advice or order placement at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M318.568.6 SKU: M318.568.6 Brand: Metav IndustryLine Facts Length: 80 mm Width: 12 mm Measuring pin diameter: 5–6 mm Special features Material: anodised aluminium Double-sided GO/NO‑GO configuration Colour-coded green and red For the reception of measuring pins FAQ What pin diameters does the holder accept? The holder accepts measuring pins with a diameter of 5–6 mm, allowing secure seating for common inspection pins. How does the GO/NO‑GO colouring work? The two faces are colour-coded green and red to indicate pass or fail visually; the double‑sided design permits immediate comparison without additional markers. Is the holder suitable for bench jigs and mobile kits? Yes, the compact 80 mm length and lightweight anodised aluminium construction make the holder appropriate for bench jigs and portable inspection sets; the design keeps handling straightforward and repeatable. Can the holder be used with precision plug gauges? The holder is intended for measuring pins and plug‑type inspection pins of 5–6 mm diameter and integrates well into manual checks alongside precision gauges. What is the item code for ordering and inventory? The product is listed under the article/SKU M318.568.6 for streamlined ordering and inventory management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6,01-7mm Messstift-Sätze, Werkstatt-Ausführung, ± 0,004 mm
- aus Spezial-Stahl Werkstatt-Ausführung, Länge 50 mm Genauigkeit < ± 0,004 mm im Behältnis/KastenTechnische Daten- Messbereich: 6,01-7mm- Stufung: 0,01mm- Anzahl/Satz: 100
6,01–7 mm Gauge Pin Set 100 Pieces Step 0.01 mm Special Steel Plastic Case - Metav IndustryLine
Benefit from a complete 100-piece gauge pin set (6.01–7.00 mm, 0.01 mm increments) made from special steel and supplied in a secure transport case; this combination delivers reliable repeatability and simple handling for workshop inspection tasks. Order directly via Metav Werkzeuge or consult the team for technical advice and prompt delivery. Gauge Pin Set M318.556 — 100-piece, 6.01–7.00 mm, 0.01 mm increments (Metav IndustryLine) The Gauge Pin Set M318.556 offers a compact, graduated diameter range for quick Go/No‑Go checks and precise nominal-diameter verification in inspection and jig setup. 100 precision gauge pins, 0.01 mm increments Range 6.01–7.00 mm for small-diameter checks Special steel for sustained wear resistance Supplied in transport case for secure storage Speed and repeatability for everyday inspection The graduated pins provide a direct, tactile method for diameter verification that reduces measurement time compared with repeated instrument setups. With 0.01 mm increments across the set and an indicated accuracy of 0.002 mm, the kit supports fast Go/No‑Go and limit checking, improving process throughput in small-bore inspection tasks. The 100 pins allow immediate selection of the nominal or test diameter without improvised stacking, which lowers the risk of human error during routine checks. Robust construction that keeps service cycles long Manufactured from special steel, the pins resist wear under repeated entry into bores and gauges; the material choice balances hardness and dimensional stability to preserve fit tolerances. Each piece is finished for smooth insertion, which reduces scoring on delicate workpieces. Supplied together in a transport case, the set is protected in transit and storage, maintaining organisation on the workbench and ensuring that each pin remains traceable within the kit. Practical benefits in workshop and toolroom use The set is suited to rapid inspection, plug-testing mandrels and reamers, and use as reference gauges during assembly or setup. The physical nature of the pins means immediate visual and tactile feedback during a pass/fail check, shortening decision cycles on the shop floor. This straightforward method integrates well with existing quality-control routines, providing a low-hardware, high-confidence solution where optical or electronic methods are not required. Handling, content and compatibility notes Contents include the stepped diameter range from 6.01–7.00 mm at 0.01 mm intervals, arranged for quick retrieval. The overall kit weight of approximately 3 kg makes it easy to keep at a workstation or transfer between departments. Because the set is delivered as a complete kit in a protective case, storage and transport are simplified and the risk of loss or mix-up is reduced — an advantage for busy production environments that demand consistent inspection readiness. For dependable small-bore testing choose the Metav IndustryLine gauge pins — contact Metav Werkzeuge for tailored advice and reliable supply from Emmerich. Technical data SKU: M318.556 GTIN: 4054469129396 Manufacturer: Metav IndustryLine Facts Measurement range: 6.01–7.00 mm Increment (step): 0.01 mm Indicated accuracy: 0.002 mm Pieces per set: 100 Weight: 3 kg Tariff number: 90173000 Special features Material: special steel Supplied in transport case Set format for quick diameter selection Intended for Go/No‑Go and nominal checks FAQ What sizes are contained in the set? The set covers diameters from 6.01 to 7.00 mm in 0.01 mm steps; the Gauge Pin Set M318.556 comprises 100 individual pins for continuous coverage across that band. What material are the pins made from? The pins are manufactured from special steel, chosen for dimensional stability and wear resistance appropriate to frequent bore testing. Is the kit supplied in protective packaging? Yes, the complete set is delivered in a dedicated transport case to protect the pins during storage and handling. What accuracy can be expected when using these pins? The set lists an accuracy figure of 0.002 mm and provides 0.01 mm grading, making it suitable for fine workshop checks and repeatable pass/fail assessments. Which workshop tasks are typical for this gauge pin set? Common uses include plug checks of bores, set-up verification of mandrels and reamers, and quick Go/No‑Go inspection during assembly or incoming goods checks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.01-7.00mm Test Pin Set 101pcs With Holder 0.01mm Graduation - Metav IndustryLine
The set combines fine 0.01 mm gradation, ±0.004 mm measurement accuracy and a special-steel design for repeatable inspection results; supplied with a pin holder and protective case for secure transport. Order the kit directly via Metav Werkzeuge or consult the technical team for application-specific guidance. Gauge pin set, 101-piece (6–7 mm) — 0.01 mm gradation, Metav IndustryLine The Gauge pin set (6–7 mm) is a compact precision kit designed for dimensional checking and tolerance verification in workshop and quality‑control environments. Fine 0.01 mm gradation Measurement tolerance ±0.004 mm 6.01–7.00 mm measurement range Supplied with pin holder Delivered in protective case Precision that speeds inspection and reduces rework The 6.01–7.00 mm kit is tailored for fine‑mechanical measuring tasks where repeatability matters. With a 0.01 mm gradation and a measurement tolerance of ±0.004 mm, the pins provide a verifiable reference for go/no‑go checks and concentricity tests. The compact set format reduces probe changes and eases handling during batch inspections, which shortens setup time and lowers the risk of measurement‑related rework. Durable construction for everyday shop use Manufactured from special steel, the pins resist wear under frequent contact and maintain dimensional stability over time. The inclusion of a dedicated pin holder ensures secure mounting and faster alignment in gauges or test fixtures, while the protective case keeps the components organised during storage and transport. These practical design choices support reliable routine use in both maintenance and production environments. Application scope and compatibility Classified in the micro‑range for fine work, the set suits inspection tasks in toolrooms, small‑component assembly and precision maintenance. The pins serve as master gauges for plug measurements, bore checking and fixture setup; the tight ±0.004 mm tolerance makes the kit suitable where tight fits and small clearances are involved. The compact format also supports efficient inventory of reference standards in controlled inspection benches. For tailored inspection kits or application advice from Metav IndustryLine, contact Metav Werkzeuge at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M318.576 GTIN: 4054469168302 Label: Gauge pin set, 101-piece, 6–7 mm, with pin holder, 0.01 mm gradation Facts Measurement range: 6.01–7.00 mm Gradation: 0.01 mm Measurement tolerance: ±0.004 mm Weight: 2.68 kg Pieces per set: 101 Special features Material: special steel Supplied with pin holder Delivered in protective case for transport Tariff number: 90173000 FAQ What tolerance can be expected from this gauge pin set? The Metav IndustryLine gauge pin set (M318.576) is specified with a measurement tolerance of ±0.004 mm. Which measurement range is covered by the pins? The set covers the 6.01–7.00 mm range, supplied in fine 0.01 mm increments for stepwise reference. Is a holder included for easy handling? Yes, the kit includes a pin holder for secure mounting and quicker alignment during inspection tasks. What material are the pins made from? The pins are manufactured from special steel, chosen for wear resistance and dimensional stability. Is the set supplied ready for transport and storage? The components are delivered in a protective case to keep the pins organised and protected during transport. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.01mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from the combination of ±0.001 mm tolerance, a 6.01 mm diameter and workshop‑grade construction for reliable end‑measurement checks; order directly via Metav Werkzeuge or consult our specialists for specification support. Gauge pin M323.601 — 6.01 mm, ±0.001 mm, workshop design (Metav IndustryLine) A Gauge pin M323.601 engineered for accurate end‑measurement and insertion checks in inspection benches and workshop fixtures. Workshop design for robust daily use Diameter 6.01 mm with ±0.001 mm accuracy Length 50 mm for stable insertion Made from special steel for wear resistance Repeatable accuracy for dependable inspection results The gauge pin delivers ±0.001 mm dimensional accuracy, making it suitable for fine end‑measurement tasks where repeatability matters. Manufactured to tight tolerances, the 6.01 mm diameter ensures consistent seating in precision jigs and go/no‑go assemblies. This level of control reduces measurement scatter and supports quicker pass/fail decisions on production lines, improving throughput while maintaining documented quality evidence. Robust construction tailored to workshop environments Built as a workshop execution variant, the pin is made from special steel chosen for strength and surface durability. The 50 mm length provides a stable engagement depth during insertion, reducing lateral play and easing handling during repetitive checks. Delivered in a transport case, the unit reaches the workshop protected from transport damage and ready for immediate use in daily inspection routines where mechanical resilience is essential. Practical integration into inspection workflows The compact geometry and consistent finish of this test pin simplify its use in end‑dimension verification, alignment fixtures and component seating checks. Traceability is supported by the supplied SKU and GTIN, so the part can be logged into inventory and quality records without ambiguity. Where repeat sampling and quick verification are required, the pin acts as a reliable reference master for short‑run checks and incoming inspection of precision components. Discuss tolerance requirements with Metav Werkzeuge and request the M323.601 workshop gauge pin to ensure ±0.001 mm conformity; Metav Werkzeuge offers prompt dispatch from Emmerich and specialist advice if required Technical Data Article number: M323.601 GTIN: 4061905058516 Brand: Metav IndustryLine Category: Messstifte Label: Prüfstift, einzeln, 6,01mm, +/- 0.001 mm Länge 50 mm Facts Diameter: 6.01 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.014 kg Special features Workshop execution for everyday use Material: special steel Delivery in transport case Application focus: end measurements FAQ What level of accuracy does this gauge pin provide? The Gauge pin M323.601 (Metav IndustryLine, SKU M323.601) is manufactured to a tolerance of ±0.001 mm, making it suitable for high‑precision end‑measurement checks. How is the gauge pin supplied and protected for transport? The M323.601 is delivered in a transport case to protect the pin during shipment and storage, ensuring the surface finish and dimensional integrity on arrival. What material is the pin made from and why does that matter? The test pin is produced from special steel, selected to provide a durable surface and resistance to wear, which supports consistent seating and long service life in workshop conditions. Can this pin be used for alignment and seating checks? Yes — the M323.601 is designed for reliable insertion checks and end‑dimension verification in inspection fixtures and alignment procedures, where its 50 mm length aids stable engagement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.02mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of high repeatability, workshop-grade robustness and micrometric tolerance for assured inspection results; the pin’s ±0.001 mm accuracy and 6.02 mm diameter make it suitable for reference checks and Go/No‑Go verification. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. M323.602 Gauge pin (single) – 6.02 mm ±0.001 mm, 50 mm length — Metav IndustryLine A M323.602 gauge pin designed as a compact reference pin for precision checking, end‑measure verification and plug‑gauge applications in workshop and inspection environments. High-precision tolerance ±0.001 mm Diameter 6.02 mm precision fit 50 mm length for secure engagement Workshop version for routine use Consistent micrometric accuracy for reliable decisions The pin delivers a tolerance of ±0.001 mm, which translates into a measurable advantage when distinguishing acceptable from non‑conforming parts. In routine quality checks this level of accuracy reduces uncertainty at the go/no‑go stage and shortens inspection cycles by providing a clear, repeatable reference. Such consistency supports faster decision‑making in production and inspection, lowering the risk of rework and scrap. Workshop‑grade construction for everyday handling Manufactured from special steel, the pin balances compactness and durability for regular use on the shop floor. At 50 mm overall length and a mass of about 0.014 kg, the component is easy to handle and integrate into existing plug‑gauge sets or inspection benches. The workshop version designation indicates a design focused on robustness and straightforward usability under typical industrial conditions. Easy integration into quality workflows and traceability The precision pin is supplied as a single reference item with clear identification (SKU M323.602, GTIN 4061905059476), which simplifies inventory and traceability in the quality system. As a standard reference element it complements existing measuring equipment and supports repeatable bore checks, end‑dimension verification and assembly validation. The compact format aids storage and deployment across multiple workstations without specialised fixtures. For precise replacement parts and dependable measurement results, order the M323.602 gauge pin from Metav Werkzeuge — or contact Metav Werkzeuge GmbH in Emmerich for application advice and ordering support: info@metav-werkzeuge.com, +49 2822 7131930 Technical data Article number: M323.602 GTIN: 4061905059476 Eclass: 21170231 Facts Diameter: 6.02 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.014 kg Special features Material: special steel Designation: workshop version Type: single gauge pin Category: Messstifte FAQ What is the nominal diameter and tolerance of this gauge pin? The gauge pin has a nominal diameter of 6.02 mm with a tolerance of ±0.001 mm, specified for precise fit and reference measurements. Is this item suitable for everyday workshop use? Yes, the M323.602 is a workshop version engineered for routine inspection and plug‑gauge tasks in production and tool rooms. How is the product identified for stock and traceability? Identification is by SKU M323.602 and GTIN 4061905059476, which supports inventory management and traceability in quality records. Can this pin be used for end‑measure verification and plug checks? The pin is intended as a compact reference element for end‑dimension checks, plug‑gauge verification and similar inspection tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.03mm Test Pin ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
Benefit from the combination of ±0.001 mm accuracy, 6.03 mm nominal diameter and a 50 mm length in special steel for reproducible end‑dimension checks; order the pin directly via Metav Werkzeuge or consult the technical team for application advice. M323.603 Gauge pin (single) — 6.03 mm, ±0.001 mm, 50 mm by Metav IndustryLine The M323.603 gauge pin provides a workshop‑grade reference for precise end‑dimension checks and go/no‑go assemblies in production and inspection environments. 6.03 mm diameter, ±0.001 mm tolerance 50 mm length for secure seating Special‑steel construction, workshop version Delivered in a protective transport case Repeatable reference for end‑dimension control A compact, hardwearing reference pin ensures consistent results when checking shaft seats, bores and fixture alignments. The very fine tolerance of ±0.001 mm turns uncertain checks into verifiable data, reducing rework and scrap. Built for routine use on the shop floor, the component’s 6.03 mm nominal size and 50 mm length provide stable contact for both manual gauges and fixture checks, simplifying pass/fail decision making in quality control processes. Designed to withstand workshop handling The workshop configuration combines a special‑steel material with a compact form that resists deformation during repeated use. Lightweight yet stiff, the pin’s construction reduces the influence of handling errors and maintains geometry under normal assembly stresses. Supplied as a single unit in a protective transport case, the product arrives ready for immediate integration into inspection kits, reducing downtime and protecting the reference surface in transit. Clear identification and straightforward integration Traceability and part identification are straightforward: the pin is supplied under SKU M323.603 with GTIN 4061905059483, facilitating inventory control and traceable procurement. As a single gauge pin, it serves as a convenient master for end‑measure checks, plug gauges and fixture set‑ups. Using a defined reference such as this improves process stability and supports fast, rational decisions on machining tolerances and assembly acceptance. For precision checks requiring ±0.001 mm accuracy, contact Metav Werkzeuge for purchase and technical advice — Metav IndustryLine items are available from Metav Werkzeuge; eMail: info@metav-werkzeuge.com, Phone: +49 2822 7131930 Technical Data SKU: M323.603 GTIN: 4061905059483 Description: Gauge pin, single, 6.03 mm, ±0.001 mm, length 50 mm Category: Gauge pins (Messstifte) Core specifications Diameter: 6.03 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.014 kg Special features Material: special steel Workshop version Supplied in a protective transport case Single‑piece delivery FAQ What machining and inspection tasks is this gauge pin best suited for? The gauge pin M323.603 is intended for end‑dimension checks, bore seating verification and fixture alignment tasks where a 6.03 mm reference is required and ±0.001 mm repeatability improves decision making. Is the material corrosion resistant or hardened? The pin is made from special steel in a workshop design that balances wear resistance and dimensional stability suitable for regular inspection use. How should the pin be stored to maintain accuracy? Store the pin in the supplied protective transport case when not in use; this prevents surface damage and preserves the reference diameter for reliable measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.04mm Gauge Pin, ±0.001mm, 50mm Length, Workshop Version - Metav IndustryLine
Combine ±0.001 mm accuracy with a compact Ø 6.04 mm diameter and robust special steel construction to ensure reliable end‑measurements in workshop metrology; order the gauge pin directly via Metav Werkzeuge or ask the consultants for application advice. Gauge pin M323.604 — Ø 6.04 mm, ±0.001 mm tolerance, 50 mm length (Metav IndustryLine) Gauge pin M323.604 is a single measuring pin designed for precise end‑measurements and dimensional checks in workshop and inspection fixtures. High precision ±0.001 mm tolerance Diameter Ø 6.04 mm for end‑measurements Workshop version with robust special steel Accuracy that reduces rework and secures process control The ±0.001 mm tolerance defines a high‑precision reference suitable for tight inspection limits and fine tolerance checks. As a hardened measuring element, this gauge pin provides a stable datum when used in checking fixtures, go/no‑go nests or comparative inspection routines. The narrow diameter of Ø 6.04 mm minimises intrusion into small bores or cavities, enabling repeatable end‑measurements without disturbing adjacent features. The result is fewer false rejects and a more consistent production flow — a clear rational advantage for quality‑minded workshops. Engineered for workshop durability and handling Produced in special steel and specified as a workshop version, the measuring pin resists wear from repeated contact while retaining dimensional integrity. The 50 mm overall length gives sufficient engagement for most end‑measurement tasks while remaining compact for fixture integration. The robust material choice balances hardness and toughness so that the pin withstands everyday use in machining and assembly environments. This combination supports reliable measurement cycles with minimal maintenance effort. Practical packaging and traceable identity for industrial use Supplied as a single item and delivered in a transport box for safe handling, the pin is protected during storage and transit. The clear product identity (SKU M323.604; GTIN included in the technical data) simplifies inventory and traceability in a busy workshop. Using a clearly identified reference pin reduces search time and helps maintain consistent inspection routines — a pragmatic benefit that supports efficient shop‑floor practices. Suitable tasks and integration into inspection workflows The compact gauge pin is intended primarily for end‑measurements, plug checks and fixture reference points where tight tolerances are required. Its small footprint makes it straightforward to incorporate into existing nests and jigs or to use as a handheld reference in quick verification tasks. Where repeated, high‑frequency checks are needed, the pin’s construction and tolerance specification help maintain short cycle times while delivering precise, verifiable results. Contact Metav Werkzeuge for tailored advice on integrating the M323.604 gauge pin into inspection fixtures and to arrange supply from our Emmerich quality hub — eMail: info@metav-werkzeuge.com or Tel: +49 2822 7131930 Technical data Article number: M323.604 GTIN: 4061905059490 Label: Gauge pin, single, Ø 6.04 mm, ±0.001 mm, 50 mm Facts Diameter: Ø 6.04 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.014 kg Special features Material: special steel Version: workshop execution Packaging: supplied in transport box Application: end measurements Single item delivery FAQ What is the exact diameter and tolerance of this pin? The gauge pin M323.604 has a diameter of Ø 6.04 mm with a specified tolerance of ±0.001 mm, suitable for high‑precision end‑measurements. Which material is used for the pin? The measuring pin is made from special steel, selected for wear resistance and dimensional stability in routine workshop use. Is the pin supplied calibrated or with a certificate? The product data does not indicate a supplied calibration certificate; the item is delivered as a single gauge pin in transport packaging. For calibration options or certificates, Metav Werkzeuge can advise on available services. How is the pin typically used in inspection setups? This compact pin is intended as a reference for end‑measurements, plug checks and integration into inspection nests or fixtures where a narrow diameter and high tolerance are required. Can the pin be used in automated or high‑cycle environments? Yes — the robust workshop execution and the ±0.001 mm specification make the pin suitable for frequent checks and integration into repetitive inspection workflows, provided handling and fixture design limit impact and wear. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.05mm Gauge Pin Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Taking advantage of workshop-grade construction, ultra‑fine ±0.001 mm tolerance and a compact 50 mm shaft length ensures reproducible end‑measurements and reliable gauging in routine inspection tasks; order the gauge pin directly via Metav Werkzeuge or consult our specialists for application advice. M323.605 gauge pin — 6.05 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) The M323.605 is a workshop‑grade 6.05 mm gauge pin designed for precise end‑measurements, bore checking and fixture setting in metalworking and quality control environments Workshop‑grade construction Diameter 6.05 mm ±0.001 mm tolerance 50 mm shaft for stable handling Special steel for lasting wear resistance Reproducible accuracy for production control The pin delivers an accuracy of ±0.001 mm, equivalent to 1 µm, which supports tight tolerance checks and decisive go/no‑go assessments on machined parts. Such resolution reduces uncertainty during quality control, enabling quicker acceptance decisions and fewer reworks. Through a small form factor and stable diameter, this measuring element suits repetitive end‑measurements where dimensional consistency is critical. Durable design made for everyday workshop use Constructed from special steel, the component withstands regular handling and contact with machined surfaces while maintaining diameter stability over time. The 50 mm shaft length offers a practical balance between gripability and rigidity, simplifying manual positioning in jigs and fixtures. The workshop‑grade finish is optimised for routine inspection cycles, providing dependable performance on the shop floor without unnecessary fragility. Versatile role in fixturing and bore inspection This gauge pin is intended for insertion checks, setting reference depths and verifying bore diameters as part of final inspection sequences. Its compact diameter and high tolerance make it suitable for precision locating, end‑dimension verification and assembly checks within production processes. Integration into custom fixtures or pin sets is straightforward thanks to the standardised diameter and uniform shaft geometry. For procurement or technical advice on deploying this Metav IndustryLine gauge pin in inspection workflows, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 — our specialists will advise on suitability and delivery options Technical data Article number: M323.605 GTIN: 4061905059506 Brand: Metav IndustryLine Facts Diameter: 6.05 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.014 kg Special features Material: Special steel Design: Workshop version Single piece supply Intended use: End‑measurements and bore checking FAQ What tolerance does this gauge pin offer? The M323.605 gauge pin is supplied with a tolerance of ±0.001 mm, making it suitable for micrometric end‑measurements and precise bore checks in quality control routines. Which material is used for the pin? This Metav IndustryLine gauge pin is manufactured from special steel, chosen for wear resistance and dimensional stability under normal workshop use. For which applications is the pin intended? The component is intended for end‑measurements, bore verification and fixture setting; it is well suited to production inspection and assembly checking tasks. Is the item supplied individually or in sets? The product is offered as a single gauge pin with the designation M323.605; multiple units can be ordered to create matched sets if required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.06mm Test Pin, Single, ±0.001mm Accuracy, Length 50mm, Workshop Version - Metav IndustryLine
Combining workshop-grade robustness, a precise ±0.001 mm tolerance and an exact diameter of Ø 6.06 mm, this gauge pin delivers reproducible end‑measurement checks in production and inspection tasks. Order the part directly via Metav Werkzeuge or contact our consultants for application advice. Gauge pin, single Ø 6.06 mm – ±0.001 mm, 50 mm (Metav IndustryLine) A gauge pin, single Ø 6.06 mm designed for precise end‑dimension verification and routine inspection in workshop metrology. Industrial accuracy ±0.001 mm Exact diameter Ø 6.06 mm for fit checks 50 mm length in special steel for durability Supplied in protective case for transport Precision where end dimensions matter High‑accuracy inspection relies on stable reference elements. With a declared tolerance of ±0.001 mm, this single gauge pin offers the tight control required for repeatable end‑measurement verification. The very small permitted deviation makes the pin suitable for tasks where comparative checks and serial inspection require consistent, traceable references. The tight specification reduces measurement uncertainty and simplifies decision limits in quality control processes. Built for workshop use and repeatability Designed as a workshop execution, the pin combines a compact 50 mm length with special steel construction for wear resistance and handling robustness. The modest length keeps bending and handling errors low while the material choice sustains surface integrity under frequent contact. Supplied in a protective case, the test piece is shielded during transport and storage, so it arrives ready for immediate use at the bench or in a fixture. Smooth integration into inspection workflows The single‑piece design supports rapid manual checks and machine‑based verifications alike; the form factor suits quick go/no‑go checks, plug‑type comparisons and fixture validation. Clear identification by SKU and GTIN helps with inventory and traceability across production lines. Where consistent repeatability is required, the combination of defined diameter and narrow tolerance streamlines root‑cause analysis of fit issues and reduces rework caused by ambiguous measurement results. Contact Metav Werkzeuge for sample availability or technical consultation on the Metav IndustryLine gauge pin M323.606 to secure reliable end‑measurement performance for your workshop Technical Data Article number: M323.606 GTIN: 4061905059513 SKU: M323.606 Manufacturer: Metav IndustryLine Core specifications Diameter: 6.06 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.014 kg Special features Material: special steel Workshop execution Supplied in protective case Single gauge pin FAQ What accuracy does the gauge pin provide? The gauge pin M323.606 (Metav IndustryLine) is specified with an accuracy of ±0.001 mm for end‑measurement verification. What is the intended application for this pin? The pin is intended for end‑dimension checks, fit verification and routine inspection tasks where a precisely sized reference is required. How is the item supplied and protected? The Metav IndustryLine test pin is supplied as a single piece in a protective case for safe transport and storage. How can the part be ordered or identified? Order using SKU M323.606 or GTIN 4061905059513; references ensure correct stock and traceability for the Metav IndustryLine product. Is the pin suitable for repeated workshop use? Yes, the workshop execution and special steel construction make the pin suitable for frequent use while maintaining dimensional stability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.07mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Benefit from workshop-grade reliability paired with sub-micron tolerance: the combination of ±0.001 mm accuracy, a precise 6.07 mm diameter and compact 50 mm length ensures repeatable reference measurements and fast in-process checks. Order directly via Metav Werkzeuge or consult the team for specification matching. Gauge Pin M323.607 — single gauge pin, Ø 6.07 mm, ±0.001 mm The Gauge Pin M323.607 is a workshop-grade, single reference pin designed for high-precision end‑measure checks and quick go/no-go verifications in production environments. Workshop-grade precision gauge pin Diameter 6.07 mm with ±0.001 mm tolerance Hardened special-steel construction Supplied in protective transport case Accuracy that reduces rework and speeds inspection A diameter tolerance of ±0.001 mm (1 µm) positions this gauge pin among the instruments used where dimensional limits determine part acceptance. The compact 6.07 mm size and 50 mm usable length provide a stable reference for bore and pin checks without the handling complexity of larger gauges. That fine tolerance shortens decision cycles on the shop floor: measurement results are immediately actionable, helping to reduce scrap and minimise rework in repeat production. Durable design for daily workshop use Manufactured from special steel, the pin is specified for routine workshop conditions and repetitive handling. Its modest mass and compact geometry—weight approx. 0.014 kg and a 50 mm length—support fast placement in jigs and fixtures, while the protective case included in delivery preserves the surface finish during transport and storage. The workshop-grade build balances wear resistance and dimensional stability, keeping the reference dimension reliable over many inspection cycles. Integrates simply into inspection and setup processes The pin serves as a precise reference for a range of tasks: bore verification, fixture alignment, end‑measure checks and gauge-block comparisons. The narrow diameter is particularly useful for small features in precision components, where a defined reference point improves repeatability. Delivered as a single unit with a clear product identity, the pin is suitable for both small-batch quality control and routine assembly checks, supporting consistent outcomes across shifts and machines. Contact Metav Werkzeuge for detailed delivery information and advice on integrating the Metav IndustryLine Gauge Pin M323.607 into existing inspection routines Technical data Article number: M323.607 GTIN: 4061905059520 Label: Prüfstift, einzeln, 6,07mm, +/- 0.001 mm Länge 50 mm Numerical data Diameter: 6.07 mm Measurement tolerance: ±0.001 mm Length: 50 mm Weight: 0.014 kg Materials & features Material: special steel Workshop version Supplied in transport case FAQ What level of tolerance does this gauge pin provide? The gauge pin offers a tolerance of ±0.001 mm, which corresponds to 1 µm and is suitable for high‑precision reference and acceptance checks. Is the pin suitable for small‑bore verification? Yes, the compact Ø 6.07 mm geometry is intended for small‑bore and pin verifications where a narrow, stable reference is required. Does the product come with protective packaging? The pin is supplied in a protective transport case to safeguard the measuring surface during storage and transit. What material is used for the pin and how does that affect longevity? Constructed from special steel, the pin is specified for workshop use where surface integrity and dimensional stability support repeated measurements. Which applications suit this gauge pin best? Typical uses include go/no‑go checks, fixture alignment, bore verification and end‑measure reference tasks in machining and assembly workflows. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.08mm Gauge Pin, Single, ±0.001mm Accuracy, Length 50mm, Special Steel, Workshop Version - Metav IndustryLine
Take advantage of ±0.001 mm tolerance and a 50 mm working length for highly reproducible end‑measure checks; the compact design made from special steel and the workshop‑grade finish ensure durable daily use, with delivery in a robust transport case. Order the inspection pin directly via Metav Werkzeuge or consult the Metav team for application advice. Gauge pin M323.608 — 6.08 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) M323.608 gauge pin — a workshop‑grade inspection pin designed for precise end‑measure verification and set‑up tasks in metrology and production control. Workshop‑grade precision component Diameter 6.08 mm ±0.001 mm Length 50 mm for end‑measure checks Supplied in a transport case Precision that secures repeatable end‑measure checks The inspection pin is manufactured for high repeatability in end‑dimension tasks, offering a declared tolerance of ±0.001 mm (1 µm). Such fine accuracy reduces measurement uncertainty when used for go/no‑go verification, plug‑gauging or as a reference mandrel in fixture set‑up. The small diameter and short working length make the item especially suited to tight‑tolerance checks where minimal form error and consistent contact geometry are required. This performance supports faster in‑process decisions and tighter quality control limits. Robust material and workshop design for daily handling Constructed from special steel, the component resists wear under regular use in workshop environments while preserving its calibrated profile. The workshop‑grade finish balances corrosion resistance and dimensional stability, so the gauge retains its form after repeated insertions and cleanings. The design is intended for straightforward handling and long service life, making it a practical choice where inspection frequency and throughput are high. Practical traceability and fit for inspection routines The pin is supplied in a protective transport case to maintain condition between uses and during storage or transport. With a compact footprint and low mass (approx. 0.014 kg), it integrates easily into existing inspection kits and fixture systems. The clear, graded tolerance specification and manufacturer identity facilitate traceability in quality documentation and help maintain consistent sampling routines on the shop floor. Typical applications and integration into quality workflows Ideal for end‑measure verification, plug‑gauging, and assembly jigs, this inspection pin performs well in machine shops, toolrooms and metrology benches where fine diameters must be confirmed rapidly. The component can be used as a reference for setting bore gauges or aligning mating parts during assembly. Its workshop configuration makes it particularly suitable for repetitive production checks where robustness and repeatability are priorities. Contact Metav Werkzeuge in Emmerich for procurement and technical guidance — Metav provides local stock, expert advice and pragmatic delivery solutions for precision metrology tools Technical data SKU: M323.608 GTIN: 4061905059537 Manufacturer: Metav IndustryLine Numbers / Core technical data Diameter: 6.08 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.014 kg Materials / Special features Material: special steel Workshop execution Supplied in a transport case FAQ What degree of accuracy does this inspection pin offer? The M323.608 gauge pin is specified with a tolerance of ±0.001 mm, providing micrometre‑level accuracy suitable for fine end‑measure checks and precision verification tasks. Is the gauge pin suitable for frequent workshop use? Yes. The workshop‑grade finish and special steel construction of the M323.608 make it suitable for regular handling in industrial inspection routines. Can this pin be used as a reference for bore alignment and jigs? The component is intended for end‑measure verification and is commonly used as a reference mandrel for setting bores and aligning assembly fixtures in production environments. Does the product include protection for transport and storage? The inspection pin is supplied in a robust transport case to protect the measuring surface and maintain condition between uses. Which documentation accompanies the pin for quality records? Product identification (SKU and GTIN) and the declared tolerance are provided; Metav IndustryLine supplies items with the manufacturer details needed for traceability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.09mm Gauge Pin 50mm Length ±0.001 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of ultra‑fine tolerance (±0.001 mm), a compact 6.09 mm diameter and a 50 mm special‑steel length for reliable end‑measurement checks; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.609 — single precision test pin, 6.09 mm diameter, ±0.001 mm tolerance (50 mm length) by Metav IndustryLine The Gauge pin M323.609 is a single precision gauge pin designed for workshop use and end‑measurement control, offering a fine 6.09 mm diameter with a laboratory‑grade ±0.001 mm tolerance in a 50 mm length. Single precision gauge pin 6.09 mm ±0.001 mm 50 mm special steel construction Workshop version for rugged handling Measurement‑grade tolerance for repeatable checks Exceptional metrology accuracy for tight fits This test pin delivers submicrometre repeatability with a declared tolerance of ±0.001 mm (1 micrometre), which is critical when verifying bore sizes, dowel fits or precision assemblies. The very small diameter and fine tolerance reduce measurement uncertainty when used as an end‑mass reference or in pin‑gage stacks. Such accuracy shortens inspection cycles: fewer adjustments are required during assembly and QC, because the measurement result can be relied on for pass/fail decisions. Robust design optimised for workshop environments Manufactured from special steel and specified at 50 mm overall length, the component is a single, solid test pin intended for regular use in production areas. The workshop specification focuses on handling resilience and dimensional stability under typical shop conditions. The compact form factor keeps manipulation straightforward while the material choice balances wear resistance with dimensional integrity, reducing the need for frequent replacement and helping to maintain consistent process capability. Practical integration into quality workflows The component is supplied as a single test pin and integrates easily into existing gauges, fixtures and pin jigs used in final inspection or incoming‑goods control. By using a dedicated measurement‑grade pin for go/no‑go verifications and feature checks, throughput is improved and measurement variability is reduced. The result is a more efficient inspection routine that supports traceable production decisions and stable assembly tolerances across batches. Contact Metav Werkzeuge today for tailored advice on integrating Metav IndustryLine gauge pins into quality control processes or to place an order — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M323.609 GTIN: 4061905060380 eClass: 21170231 Category: Messstifte Facts Diameter: 6.09 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.014 kg Special features Material: Special steel Version: Workshop execution Form: Single test pin Intended use: End‑measurement / pin‑gage applications FAQ What tolerance does this gauge pin offer? The gauge pin M323.609 is manufactured to a tolerance of ±0.001 mm (1 micrometre), making it suitable for high‑precision fit checks. Which material is used for the test pin? This Metav IndustryLine test pin is made from special steel, chosen for dimensional stability and wear resistance in workshop use. Is the pin suitable for use in pin‑gage fixtures and jigs? Yes; the 6.09 mm diameter and 50 mm length are compatible with standard pin‑gage holders and fixture bores for end‑measurement tasks. Can this item be used for checking dowel or bore fits? The gauge pin M323.609 is designed specifically for fit verification and end‑measurement of small bores and dowel seats where a 6.09 mm reference is required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.11mm Test Pin Single ±0.001mm Length 50mm, Workshop Version - Metav IndustryLine
High-precision reference for end measurements: a gauge pin with a nominal diameter of 6.11 mm, repeatable tolerance of ±0.001 mm and a 50 mm length; workshop-grade construction in special steel, supplied in a protective transport box. Order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.611 — single gauge pin, 6.11 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.611 is a workshop‑grade, single reference pin designed for precise end‑measurements and verification tasks in production and inspection environments. High repeatability ±0.001 mm Workshop version in special steel Compact 50 mm length for tight fixtures Supplied in protective transport box Precision where repeatability matters A nominal diameter of 6.11 mm combined with a tolerance of ±0.001 mm provides a dependable reference for go/no‑go checks and comparative measurements. The extremely small tolerance reduces measurement uncertainty and supports consistent decision making during quality checks. The special steel construction keeps dimensional stability under routine handling, while the compact form factor makes the pin suitable for confined gauges and fixtures. This paragraph emphasises the operational benefit: faster inspection cycles with fewer ambiguous results, improving throughput without sacrificing traceability. Built for workshop conditions and practical handling Designed as a workshop version, the pin balances robustness with fine accuracy. At 50 mm overall length and a mass of 0.015 kg, the item is easy to position in tight assemblies and remains stable during contact measurements. The construction is aimed at routine use rather than delicate laboratory environments, so durability in daily production settings is a clear advantage. The delivery in a protective box reduces the risk of transport damage and helps preserve the reference geometry between uses. Use cases and compatibility with inspection workflows This single gauge pin is intended for end‑measurement tasks, calibration jigs, fixture setting and component verification. Its ±0.001 mm tolerance makes it suitable where high repeatability is required—such as batch acceptance testing or final inspection of turned and ground parts. The compact diameter and short length enable integration into small fixtures and modular inspection plates. Where traceability is needed, the pin’s defined geometry supports clear go/no‑go decisions and reliable position references within assembly processes. Handling, maintenance and storage to retain accuracy To maintain the pin’s performance, handle with clean, dry hands or gloves and avoid impacts. Store the item in its protective box between uses to prevent nicks and surface damage that would affect accuracy. Routine checks with a calibrated micrometre or a comparator are recommended if the pin is exposed to heavy handling; any visible wear or deformation should prompt replacement to avoid measurement drift. These simple measures preserve the pin’s benefits: consistent measurements, fewer rework loops and trustworthy inspection outcomes. For workshop‑grade precision from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for ordering and technical advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M323.611 GTIN: 4061905060403 Category: Messstifte Label: Gauge pin, single, 6.11 mm, ±0.001 mm, length 50 mm Facts Nominal diameter: 6.11 mm Length: 50 mm Tolerance / repeatability: ±0.001 mm Weight: 0.015 kg Special features Material: special steel Workshop version Delivered in protective transport box Intended for end‑measurements and fixture checks FAQ What tolerance does the gauge pin offer? The gauge pin M323.611 is specified with a repeatability of ±0.001 mm, making it suitable for high‑precision verification tasks. Is the pin suitable for fixture setting and end‑measurements? Yes, the M323.611 single gauge pin is intended for end‑measurements, fixture setting and go/no‑go checks in workshop inspection workflows. Does the product come with a calibration certificate? The product data does not indicate an ISO 17025 certificate for this item; please contact Metav Werkzeuge if an accredited calibration certificate is required. How should the gauge pin be stored to keep accuracy? Store the gauge pin in the supplied protective box, handle it with gloves, and avoid impacts; periodic checks with a calibrated micrometre are recommended to confirm continued dimensional accuracy. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.12mm Gauge Pin Single ±0.001mm Accuracy Length 50mm Workshop Version - Metav IndustryLine
The combination of submicron accuracy, compact dimensions and a robust workshop finish makes this gauge pin ideal for reliable end measurements; benefit from consistent fits and reduced rework. Order the gauge pin directly via Metav Werkzeuge or consult the Metav team for application advice. M323.612 Gauge Pin — 6.12 mm, ±0.001 mm (Workshop Version) by Metav IndustryLine M323.612 is a single gauge pin designed as a precise end-measurement master for workshop and inspection tasks Submicron tolerance ±0.001 mm Diameter accurately ground to 6.12 mm 50 mm length for stable seating and reference Workshop version with durable finish Reduce rejects with repeatable submicron precision The gauge pin is manufactured to a tolerance of ±0.001 mm, delivering repeatable results when used as an end-measurement master or reference pin. This level of precision minimises fit variation across production batches, cutting down on rework and inspection time. The 6.12 mm diameter is ground to size and held over the full length to ensure consistent contact geometry; the small mass also helps to avoid undue influence on delicate fixtures. Engineers and quality technicians benefit from faster decision-making thanks to fewer out-of-tolerance readings and clearer go/no-go outcomes. Built for stable seating and handling in workshop environments With a 50 mm overall length and a workshop-focused design, the pin provides a secure seating depth for probes, fixtures and assembly checks. The compact form reduces the risk of bending or deflection during handling while offering enough engagement to act as a reliable datum in jigs and checks. Made from special steel, the pin balances hardness and toughness to withstand regular use without rapid wear. The robust finish and straightness keep contact conditions consistent, which is crucial when measurements are used to validate mating parts or final assembly tolerances. Practical integration into inspection and production workflows The gauge pin is simple to incorporate into existing inspection routines: it serves as an end gauge, a locating pin for dimensional checks and a reference for comparative measurement setups. Traceability is supported by the clear SKU marking, and the compact weight (approx. 0.015 kg) makes handling straightforward during bench checks or when fitted into modular fixtures. For small-batch manufacturing and precision assembly, the pin reduces set-up variability and streamlines routine checks, providing measurable time savings in quality control cycles. For application-specific advice and to acquire the M323.612 gauge pin from Metav IndustryLine, contact Metav Werkzeuge for precise ordering and consultancy at info@metav-werkzeuge.com or by phone; Metav’s specialists will assist with selection and integration into existing measurement processes. Technical data SKU: M323.612 GTIN: 4061905060410 Product: Gauge pin, single, 6.12 mm, ±0.001 mm, length 50 mm Category: Gauge pins Manufacturer: Metav IndustryLine Facts Diameter: 6.12 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Measurement range min: 6.12 mm Measurement range max: 6.12 mm Special features Material: special steel Workshop execution Intended use: end measurements / reference pin Label: Prüfstift, einzeln (translated) FAQ What level of precision does this gauge pin offer? The M323.612 gauge pin is manufactured to a precision of ±0.001 mm, providing submicron-level repeatability suitable for tight-fit and end-measurement applications. Can the pin be used as a reference in fixture set-ups? Yes, the M323.612 gauge pin is intended for use as an end-measurement master and locating reference in jigs, fixtures and inspection routines. What material is the pin made from and how does that affect wear? The pin is made from special steel, chosen for a balance of hardness and toughness to resist wear under regular workshop handling while maintaining contact geometry. Is the diameter held over the full length? The diameter of 6.12 mm is ground and controlled for consistent contact; the 50 mm length ensures stable seating for measurement and fixture use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.13mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of workshop‑grade accuracy and robust construction to reduce inspection time and rework: the Ø6.13 mm diameter and ±0.001 mm tolerance deliver repeatable fit checks, while the 50 mm length eases access to deeper bores; order directly via Metav Werkzeuge or consult our advisers for batch supply and inventory support. Gauge pin M323.613 — Ø6.13 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.613 is a workshop‑grade test pin designed for precise end‑measure verification and fit checks in precision engineering and quality control applications. Workshop‑grade precision ±0.001 mm Diameter 6.13 mm for tight fit checks Length 50 mm for deeper bore access Supplied in protective case for transport Reduce rejects with micrometric accuracy The core advantage of this precision gauge pin is its tight dimensional tolerance of ±0.001 mm, which translates to measurable reductions in part mismatches and rework. In inspection workflows a stable reference diameter limits ambiguity during go/no‑go assessments and ensures interchangeability between mating parts. The Ø6.13 mm sizing is particularly suited to small bore gauges and end‑measure checks where clearance is minimal; the result is a faster inspection cycle and fewer downstream corrective actions. Built for the workshop: durable and easy to handle Manufactured from special steel, this test pin is prepared for routine use in workshop environments where mechanical resistance and surface integrity matter. The 50 mm length gives sufficient engagement for many bore and plug checks while remaining easy to manoeuvre by hand or in fixture setups. Supplied in a protective case, the pin is protected during transport and storage, preserving the reference surface and prolonging service life — a pragmatic choice for production floors and tool cabinets. Practical integration into inspection routines As a measuring aid, the pin functions as a simple reference for bore verification, fit trials and end‑of‑line checks. The polished shaft reduces measurement artefacts and permits swift tactile confirmation of fits. For users less familiar with gauges: a gauge pin is a hard, accurately ground shaft used to confirm that a bore or mating part meets its specified diameter — a compact and low‑complexity solution for frequent compliance checks without needing elaborate fixtures. Traceability and procurement made straightforward Identification and logistics are simplified by the clear SKU and GTIN, aiding inventory control and repeat ordering. The item is listed under measuring pins and carries the practical designation for workshop use, easing selection for production and maintenance teams. Metav’s position as a precision partner supports consistent supply: central warehousing in Emmerich and a wide product range mean fewer single‑source headaches and reliable replenishment for recurring measurement needs. Contact Metav Werkzeuge for availability of the Metav IndustryLine gauge pin M323.613 and tailored supply options; technical advice and order handling are available via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: M323.613 GTIN: 4061905060427 Manufacturer: Metav IndustryLine Facts Diameter: 6.13 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Material: special steel Workshop version Supplied in protective case Category: measuring pins FAQ What is the dimensional tolerance of this gauge pin? The gauge pin is manufactured to a tolerance of ±0.001 mm, making it suitable for tight fit assessments and precision verification with minimal uncertainty. Which materials is the pin intended to test? The test pin is a hard, accurately ground reference shaft intended for checking bore diameters and fits; it provides a reliable mechanical reference for components made from common engineering materials. Is a calibration certificate supplied with the pin? No calibration certificate is included by default; the item is delivered as a workshop‑grade gauge pin without an official calibration document. Can the pin be used as a master reference in measurement labs? The pin serves well for routine fit and go/no‑go checks; for laboratory master references with formal traceability, a laboratory calibration and certificate would be recommended. Is a case supplied for transport and storage? Yes, the gauge pin is supplied in a protective case to shield the shaft during transport and to reduce handling damage before use. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.14mm Gauge Pin ±0.001 mm Length 50 mm Workshop Version - Metav IndustryLine
Take advantage of the combination of workshop robustness, sub-micron repeatability and convenient transport packaging for dependable reference measurements; order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.614 — 6.14 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) A gauge pin M323.614 designed as a single reference pin for precise diameter checks and go/no‑go verification in workshop and inspection tasks. Precision tolerance ±0.001 mm Nominal diameter 6.14 mm 50 mm length, workshop version Special steel construction, transport case included Precise reference for fast, repeatable diameter checks The M323.614 serves as a compact, high‑precision reference for diameter verification where tight tolerances are essential. With a declared tolerance of ±0.001 mm, the cylindrical gauge provides the stability required for short comparative checks and fixture set‑up, reducing cycle time in routine inspection. The 6.14 mm nominal size and 50 mm overall length make it suitable for checking bores, pin fits and mating features where a reliable go/no‑go condition or a reference master is required. The specification supports efficient decisions in quality control processes by providing an unambiguous physical standard for pass/fail evaluation. Durable construction for daily workshop use Manufactured in special steel and specified as a workshop version, the pin balances wear resistance with dimensional stability for repeated handling. At approximately 0.015 kg, the component is easy to manoeuvre while remaining robust against incidental knocks typical in production environments. The delivery includes a transport case, protecting the gauge during storage and transit and helping to preserve the measured reference over time. These characteristics ensure that routine use on the shop floor does not compromise accuracy, so inspection intervals can be kept tight without increasing replacement costs. Practical integration into established metrology workflows This cylindrical reference element complements handheld and bench measurement tools by providing an immediate, tactile verification step that integrates with existing inspection routines. When used alongside calipers and dial gauges, the pin shortens inspection sequences by offering an exact physical dimension against which instruments or components can be compared. The clear numeric tolerance and compact form factor support traceable in‑process checks and quick fixture validation, enhancing throughput and reducing uncertainty in daily production checks. Reliable choice backed by Metav's supply chain and service Sourcing from Metav IndustryLine secures access to Europe‑centred logistics and a quality‑focused distribution hub in Emmerich. The gauge pin is supplied ready for immediate use in workshop applications; Metav's broad product range and longstanding market presence provide a dependable supply route for replacements or additional sizes. For specialised measurement chains or advice on selecting complementary reference standards, Metav Werkzeuge can provide pragmatic guidance to align the pin with specific application requirements. Contact Metav Werkzeuge for application advice and to secure the M323.614 gauge pin with prompt delivery from Emmerich Technical data Article number: M323.614 GTIN: 4061905060434 Description: Gauge pin, single, 6.14 mm, ±0.001 mm, length 50 mm Facts Diameter: 6.14 mm Length: 50 mm Tolerance: ±0.001 mm Weight: 0.015 kg Special features Material: Special steel Workshop version Delivered in transport case FAQ What is the declared tolerance of this gauge pin? The M323.614 gauge pin is specified with a tolerance of ±0.001 mm, offering sub‑micron repeatability for comparative checks. Which materials and applications suit this pin? Made from special steel, the pin is intended for general workshop inspection tasks such as bore checks, pin fits and go/no‑go verifications in metalworking and assembly environments. Does the delivery include protection for transport and storage? Yes, the gauge pin is supplied in a transport case to protect the reference surface during transit and workshop storage. How does this pin fit into existing inspection processes? The pin acts as a tactile reference for quick comparative measurements and fixture validation, complementing calipers and dial gauges to shorten inspection cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.15mm Gauge Pin Single, Workshop Version, ±0.001mm Accuracy, 50mm Length, Special Steel, Supplied in Case - Metav IndustryLine
Taking advantage of Ø 6.15 mm, ±0.001 mm tolerance and a 50 mm length ensures reliable end‑measurements and consistent fit verification in workshop inspection routines; the workshop‑grade construction and special steel deliver dimensional stability under repeated use. Order the gauge pin M323.615 directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.615 — single inspection pin, Ø 6.15 mm, ±0.001 mm (Metav IndustryLine) Gauge pin M323.615 is a workshop‑grade inspection pin designed for precise bore and fit verification in quality control and assembly environments Workshop-grade precision pin, ±0.001 mm Diameter Ø 6.15 mm for tight bore checks Length 50 mm for deep seat verification Made from special steel for dimensional stability Precise dimension control for critical fits The gauge pin provides high‑resolution reference for bore checks and end‑measurements, combining a tight tolerance of ±0.001 mm with a nominal diameter of Ø 6.15 mm. Such precision reduces uncertainty during inspection and supports reproducible acceptance criteria for mating parts. For teams assessing press fits, plug gauges or radial clearances, this inspection pin functions as a reliable datum: the narrow tolerance helps to quickly determine whether a bore is within a specified limit or requires rework, thereby streamlining quality decisions on the shop floor. Durable workshop construction that maintains accuracy Manufactured from special steel, the pin resists wear and maintains geometry during repeated insertions and extractions. The 50 mm length offers sufficient engagement for many practical checks while keeping handling straightforward; shorter tools can twist or deflect, but this design balances stiffness with accessibility. The workshop‑grade finish eases cleaning and prevents rapid corrosion in standard production environments, which helps to preserve the calibrated dimension over many cycles and reduces the need for frequent replacement. Practical handling and integration into inspection routines As a single gauge pin, the component simplifies set‑up compared with multi‑element fixtures: it is easy to seat, easy to visualise and quick to compare against limit gauges or master pins. The compact form factor speeds routine checks at receiving inspection, in‑process control or final assembly. Traceability is supported via the SKU and GTIN entries, enabling inventory control and clear identification in inspection logs. For bench testing and small jig work the pin serves as a straightforward reference that eliminates guesswork and shortens inspection time. Fit for purpose and shop‑floor benefits Engineered for consistent performance in repetitive tasks, this inspection pin offers measurable gains in throughput and measurement confidence. The tight accuracy reduces the margin for interpretation during pass/fail decisions, which lowers scrap and rework rates. Its simple geometry and robust material mean maintenance is limited to basic cleaning and periodic dimensional checks, maintaining uptime in high‑volume production. The result is a pragmatic, accurate tool that supports repeatable quality outcomes without complex handling. For workshop enquiries or to confirm compatibility with specific inspection setups, contact Metav Werkzeuge to secure the Metav IndustryLine gauge pin M323.615 and discuss inspection integration on the production line. Technical Data Article number: M323.615 SKU: M323.615 GTIN: 4061905061042 Brand: Metav IndustryLine Version: Werkstatt-Ausführung Material: Spezial-Stahl Numbers / Core technical data Nominal diameter: Ø 6.15 mm Tolerance / accuracy: ±0.001 mm Length: 50 mm Weight: 0.015 kg Messbereich min: 6.15 mm Messbereich max: 6.15 mm Genauigkeit versch: ±0.001 Designs / Special features Single gauge pin configuration Workshop‑grade finish Intended use: end measurements and bore verification Category: Messstifte Storytrigger: endmasse FAQ What material is the pin made from? The gauge pin M323.615 is manufactured from special steel, giving good wear resistance and dimensional stability for routine workshop use. Is the tolerance sufficient for precision fitting checks? Yes, the ±0.001 mm tolerance of this inspection pin supports verification of tight fits and small clearances where micrometre‑level accuracy is required. For which applications is the pin intended? The inspection pin is intended for end‑measurements, bore verification and fit checks in receiving inspection, in‑process control and assembly procedures. Does the pin include a traceable identifier for inventory and QC? The product is listed with SKU M323.615 and GTIN 4061905061042, enabling clear identification in inventory and inspection documentation. How should the pin be cared for to preserve accuracy? Regular cleaning after use, gentle handling to avoid knocks and periodic dimensional verification are recommended to maintain the pin's accuracy and service life. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.16mm Gauge Pin, ±0.001mm Accuracy, 50mm Length, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
A compact inspection solution that pairs ±0.001 mm accuracy with a 6.16 mm diameter and a robust special steel construction, making it ideal for repeatable end‑measure checks in workshop environments. Supplied as a single, 50 mm long gauge pin for straightforward integration into inspection routines — order the gauge pin directly via Metav Werkzeuge or ask our consultants if needed. Gauge pin M323.616 — 6.16 mm, ±0.001 mm (Metav IndustryLine) The gauge pin M323.616 is a single precision pin designed for end‑measure verification and go/no‑go checking in workshop and inspection settings. Workshop version for daily shop use Diameter precisely 6.16 mm Tolerance ±0.001 mm for high repeatability Length 50 mm, compact and easy to handle Precise measurement where it matters This single gauge pin delivers ±0.001 mm tolerance for demanding inspection tasks, translating into reliable go/no‑go decisions and reproducible end‑measure checks. The fine accuracy stabilises quality control processes by reducing measurement uncertainty at the point of contact; when combined with consistent handling, the result is fewer rework cycles and a clearer pass/fail signal on component inspection. The 6.16 mm diameter is held to tight tolerances to ensure repeatable fitment in gauges and fixtures. Tough workshop construction for everyday use Engineered as a workshop version, the pin is made from special steel that stands up to routine handling without compromising metrology properties. At 50 mm length and approximately 0.015 kg, it balances stiffness with ease of manipulation, simplifying insertion into jigs and test fixtures. Supplied individually and protected for transport in a case suitable for workshop environments, the construction minimises surface damage and preserves the reference diameter between uses. Practical applications and system integration Ideal for end‑measure verification, fixture checks and dimensional validation, the pin suits use in incoming inspection, assembly stations and maintenance workshops. The single‑piece design supports quick replacement in modular gauge systems and straightforward inclusion in calibration routines. Its compact size and precise diameter make it appropriate for checking bore quality, locating features and verifying mating parts where a defined reference diameter is required. For robust, repeatable inspection choose the Metav IndustryLine gauge pin M323.616 — contact Metav Werkzeuge for technical guidance or to arrange supply from our Emmerich centre Technical Data Article number: M323.616 GTIN: 4061905061448 ECLASS: 21170231 Designation: Gauge pin, single, 6.16 mm, ±0.001 mm, length 50 mm Facts Diameter: 6.16 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Material: special steel Workshop version Supplied individually in a protective transport case Suitable for end‑measure and go/no‑go tasks FAQ What inspection tasks is this gauge pin best suited for? The gauge pin M323.616 is intended for end‑measure verification, go/no‑go checking and fixture validation where a 6.16 mm reference diameter and ±0.001 mm precision are required. Is the pin supplied as a single item or in a set? This offering is a single gauge pin (SKU M323.616), supplied individually and protected for transport to preserve the measuring surface. What material is used and how does that affect use? Made from special steel, the pin combines wear resistance with dimensional stability, supporting frequent use in workshop inspection without rapid degradation. Can this pin be used in fixture systems and gauge blocks? Yes; the pin’s tight tolerance and compact 50 mm length make it suitable for integration into fixtures and modular gauge systems for reliable mating and measurement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.17mm Gauge Pin, Single, ±0.001mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of sub‑micrometre accuracy, workshop‑ready robustness and compact length for reliable end‑dimension inspection. Order the gauge pin directly via Metav Werkzeuge or request technical clarification from our consultants to ensure seamless integration with existing gauges and fixtures. Gauge pin M323.617 — precision test pin, 6.17 mm ±0.001 mm, 50 mm A gauge pin M323.617 designed for precise end‑dimension checks and workshop gauging tasks in machining and quality control environments. 6.17 mm diameter ±0.001 mm accuracy 50 mm length for deeper bore access Special steel for high wear resistance Workshop version delivered in protective case Consistent one‑micrometre precision for end‑dimension control The instrument delivers ±0.001 mm tolerance, corresponding to 1 µm resolution, which translates into significantly more reliable pass/fail decisions during final inspection. Such fine accuracy reduces uncertainty in end‑dimension verification and helps to cut rework rates; the precision is suitable for tight tolerance seats, pins and mating bores where reproducibility matters. Where traceable measurement is required, the pin’s specification supports integration into calibrated inspection routines and fixture checks. Robust construction that stands up to workshop use Manufactured from special steel and specified as a workshop version, the pin combines surface durability with a compact form factor. The 50 mm length permits access to deeper features while keeping handling straightforward; the low mass supports rapid gauging cycles without undue operator fatigue. Delivery in a protective case safeguards the finish during transport and storage, maintaining the contact geometry that underpins repeatable measurements. Practical applications and compatibility with inspection workflows Intended primarily for end‑dimension inspection, the pin is a versatile tool for bench gauging, fixture validation and batch end‑checking. The compact diameter of 6.17 mm makes it suitable for fine hole and bore verification where micro‑accuracy is required. Integration into existing gauge sets is straightforward: the component’s consistent geometry and workshop rating mean it can be used in manual or semi‑automated checking stations as a reference element or functional gauge. For reliable end‑dimension inspection using Metav IndustryLine precision parts, request the M323.617 gauge pin through Metav Werkzeuge for expert guidance and dependable delivery — contact info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M323.617 GTIN: 4061905061455 SKU: M323.617 Material: Special steel Accuracy: ±0.001 mm Length: 50 mm Diameter: 6.17 mm Weight: 0.015 kg Facts Diameter: 6.17 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Workshop execution Delivered in protective case for transport Intended for end‑dimension inspection Compact, low‑mass design for rapid handling FAQ What is the measurement tolerance of this gauge pin? The gauge pin M323.617 has a specified tolerance of ±0.001 mm, equal to 1 µm, suitable for high‑precision end‑dimension checks. Which materials is the pin suitable for checking? The pin itself is made from special steel and is intended as a reference element for inspection of machined components; compatibility with specific workpiece materials depends on the inspection method rather than the pin material. Is the gauge pin supplied ready for use in workshops? Yes, this workshop version is supplied in a protective case to preserve the contact surface during transport and handling. Can the pin be integrated into existing fixtures or gauge blocks? The compact diameter and standard geometry make the pin suitable for use as a reference in fixtures, gauges and manual checking stations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.18mm Test Pin, Single, ±0.001 mm Accuracy, 50mm Length, Workshop Version - Metav IndustryLine
Take advantage of the combination of extreme dimensional accuracy, robust workshop design and traceable identification for reliable end‑measurement tasks; order the single gauge pin directly via Metav Werkzeuge or consult the specialists for application advice. Gauge pin M323.618 — 6.18 mm, ±0.001 mm, 50 mm length (Metav IndustryLine) Gauge pin M323.618 is a single precision test pin for end‑measure verification and plug‑gauge tasks in workshop and inspection environments. ±0.001 mm tolerance for sub‑micron checks 6.18 mm diameter for end‑measure standards 50 mm length for versatile positioning Special steel, workshop version for durable use Accuracy that reduces uncertainty in inspection The central advantage of this precision test pin is its ±0.001 mm tolerance, which corresponds to a one‑micrometre limit and significantly lowers measurement uncertainty in critical fit and end‑dimension checks. By using a reference pin with such a tight specification, inspection routines become more reproducible and allow for clear go/no‑go assessment when validating mating parts. The tight tolerance is especially beneficial where small clearances determine assembly performance, as the single pin offers a fast, objective measure compared with subjective visual or feel‑based checks. Built for workshop handling and repeatability Made from special steel and specified as a workshop version, the pin combines wear resistance with practical handling for regular use. The 50 mm shank provides comfortable engagement in gauges, jigs or fixture sockets while the compact mass supports quick temperature equalisation to ambient conditions, reducing thermal drift during short checks. Robustness translates into fewer replacements and more consistent outcomes over time, which supports production continuity and reduces rework. Practical use and system integration As a single gauge pin for end‑measure tasks, this component suits inline checks, manual plug tests and setup operations where a defined reference diameter is required. The nominal 6.18 mm diameter is useful as a control measure for bores and mating features in precision assemblies. Labelling and clear identification facilitate traceable inspection records; pairing the pin with calibrated master gauges or digital measurement logs ensures results are auditable. For operations seeking straightforward, repeatable inspection steps, the pin streamlines decision points without complex fixturing. For dependable sub‑micron end‑measure verification, contact Metav Werkzeuge to discuss the M323.618 gauge pin and application‑specific recommendations from our specialists Technical Data Article number: M323.618 GTIN: 4061905061462 Brand: Metav IndustryLine Label: Prüfstift, einzeln, 6,18mm, +/- 0.001 mm Länge 50 mm Core specifications Diameter: 6.18 mm Tolerance/accuracy: ±0.001 mm Length: 50 mm Weight: 0.015 kg Features & materials Material: Special steel Version: Workshop execution Single test pin for end‑measure verification Intended use: Reference/plug checks FAQ What is the exact tolerance of the pin? The M323.618 gauge pin is specified at ±0.001 mm, providing one‑micrometre level tolerance for precise end‑measure checks. For which inspection tasks is this pin suitable? This single test pin is intended for end‑measurement and plug‑gauge checks, making it suitable for dimensional verification of bores, fit tests and setup controls in workshop and inspection processes. What material is used for the pin and why does it matter? The pin is manufactured from special steel, chosen for wear resistance and dimensional stability under normal workshop conditions, which prolongs service life and maintains repeatability. Can the pin be used as a reference in traceable measurement routines? Yes. The M323.618 functions as a straightforward reference artefact; when combined with calibrated masters or documented procedures, it supports auditable inspection results. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
6.19mm Gauge Pin, Single, ±0.001mm, Length 50mm, Workshop Version, Special Steel, Supplied in Case - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, ±0.001 mm dimensional accuracy and a 50 mm functional length for dependable end-measurement and gauge-setting tasks. Order the pin directly via Metav Werkzeuge or request specification advice from Metav's consultants. M323.619 Gauge Pin — single gauge pin, 6.19 mm diameter, ±0.001 mm tolerance (Metav IndustryLine) The M323.619 gauge pin is a workshop-grade, single end-measurement pin designed for precise plug and end-gauge tasks in quality control and inspection routines across mechanical workshops and metrology benches. Workshop-grade construction Diameter precisely 6.19 mm Tolerance ±0.001 mm for accuracy Supplied in protective transport box Reduce inspection uncertainty with micrometric tolerance The precision ±0.001 mm tolerance ensures that the pin performs reliably in pass/fail checks and gauge setting, reducing measurement uncertainty in repeat inspections. As a hard-ended, single-piece measuring pin, it delivers a consistent reference for go/no-go assessments and end-stop calibration. This level of accuracy supports traceable in-process checks and contributes to predictable quality output across production batches. Durable build for repeatable measurements in workshops Manufactured from special steel and finished for workshop use, the pin withstands the routine handling typical of industrial metrology. The robust material selection and compact geometry preserve dimensional stability during repeated seating and extraction cycles, which helps to keep instrument wear low and maintenance intervals predictable. The compact form factor also minimises the risk of deflection, supporting reproducible contact geometry for end-measurement tasks. Practical handling and integration into inspection workflows With a nominal diameter of 6.19 mm and a 50 mm usable length, the pin is suited to tight-fit checks, fixture set-up and end-measurement roles where precise datum control is required. Supplied in a transport box for secure shipping, the component is ready for storage or immediate use at the workshop bench. Its straightforward geometry allows fast visual identification and simple integration into existing gauge stacks or fixture insertions without special adapters. Contact Metav Werkzeuge today for application guidance or to request this Metav IndustryLine gauge pin with guaranteed workshop packing and specification details Technical data Article number: M323.619 GTIN: 4061905061479 Manufacturer: Metav IndustryLine Facts Diameter: 6.19 mm Tolerance: ±0.001 mm Length: 50 mm Weight: 0.015 kg Special features Workshop version Material: Special steel Supplied in transport box for safe shipping Single gauge pin for end-measurement applications FAQ What is the declared tolerance of this gauge pin? The M323.619 gauge pin is manufactured to a tolerance of ±0.001 mm, providing micrometric repeatability for inspection and gauge-setting tasks. Is the pin supplied ready for workshop use? The pin is delivered as a workshop-grade component in a protective transport box and is suitable for immediate integration into inspection setups. What material is used for the pin? The component is made from special steel, selected for dimensional stability and resistance to routine handling typical of workshop metrology. For which tasks is this gauge pin intended? The pin is intended for end-measurements, plug and go/no-go checks, and as a reference element for setting gauges and fixtures in quality control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Highest accuracy with immediate pass/fail certainty
Pin gauges (also known as gage pins or pin gauge sets) deliver micrometre-level certainty for bore, thread and radius inspection. Designed for industrial precision manufacturing, tool and mould making and quality assurance, these mechanical gauges provide an unequivocal physical result — pass or not pass — without reliance on electronics. The result is faster decision-making at the gauge or directly at the machine.
How pin gauges work in demanding production environments
Pin gauges are tactile reference tools for the quick verification of the smallest diameters, bore centres and form accuracy. Inserted into a bore or mating feature, a correctly sized pin gauge confirms dimensional conformity by fit; mismatches are immediately apparent. Their simple mechanical principle makes them ideal for in‑process checks on the shop floor as well as in the metrology room, and they are commonly used for bore inspection, internal thread checks, measuring tooth widths, assessing taper bores and setting indirect measuring devices.
Measurable benefits that matter on the shop floor
- Highest precision: available in standardized accuracy classes such as DIN 2269, with tolerances down to ±1 µm or ±2 µm, enabling reliable verification of the strictest quality requirements.
- Robust materials: manufactured from hardened gauge steel, wear‑resistant ceramic or carbide, providing long life under repetitive use.
- Exceptional surface quality: finely lapped and distortion‑free to ensure repeatable contact results.
- Clear identification: each pin is permanently and legibly marked with its nominal size, reducing errors during fast inspection cycles.
- Flexible supply: offered as individual pins or complete pin gauge sets in sturdy wooden cases for organised storage and rapid access.
Metav — practical precision for every workshop
Metav combines decades of metrology expertise with a comprehensive portfolio to democratise high‑accuracy measurement. From Emmerich, a “quality filter” for the European market, Metav supports industry and trade with over 250,000 products and the trust of more than 48,000 customers. That background makes Metav a pragmatic choice for workshops seeking reliable pin gauges and tailored inspection solutions.
Summary
For uncompromising micrometre accuracy in bore and form inspection, pin gauges and gage pins offer a direct, durable and process‑ready solution that reduces uncertainty and speeds up production decisions.
FAQ
What tolerance classes are available for pin gauges?
Pin gauges are supplied in standardised accuracy classes such as DIN 2269, with typical tolerances of ±1 µm or ±2 µm to meet rigorous industrial quality specifications.
Which materials are used for pin gauges?
Common materials include hardened gauge steel, wear‑resistant ceramic and carbide, selected according to the expected wear, handling and measurement environment.
How are pin gauges identified and stored?
Each pin is permanently engraved with its nominal size for unmistakable identification; sets are often supplied in organised wooden cases for safe storage and fast retrieval.
Can pin gauge sets be configured for specific series dimensions?
Yes. Metav’s range allows combination of individual pins into customised pin gauge sets, enabling tailored coverage for repetitive series dimensions and efficient inspection routines.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com