Precision angle gauges for reliable right-angle control
Angle gauges and inspection squares provide dependable verification of right-angle geometry and ensure accurate alignment in metalworking assemblies. Used for tasks ranging from rough marking with a machinist's square to high-precision verification with hardened and lapped control angles, these tools prevent fitment errors and functional faults by detecting even minute deviations from 90° and other set angles. For heavy-duty applications such as flange alignment in piping and vessel fabrication, robust flange squares offer stable seating on curved surfaces, while sine bars and adjustable angle gauges enable trigonometrically exact measurements for non‑standard angles. Regular calibration and inspection of leg flatness and wear are essential to maintain measurement integrity.
60cm Angle Electronic Protractor 0.05° Resolution 0.1° Accuracy, IP54 - BMI
Take advantage of precise angle measurement, a clear illuminated display and user-friendly handling to speed up setup and inspection tasks; order the device directly via Metav Werkzeuge or consult the Metav specialists for advice. Winkeltronic electronic angle meter (Winkelmessgerät) – 0–355°, 60 cm arms (BMI) A Winkeltronic electronic angle meter designed for precise measuring and transferring of angles across a near-full circle, ideal for workshop alignment and layout tasks Large illuminated display for clear readings High resolution of 0.05° for fine adjustments Symmetrical 60 cm arms for stable positioning Hold function and zeroing in any arm position High-precision measurement for reliable alignment The device provides a measuring range of 0–355° with a finely graduated resolution of 0.05° and an accuracy of ±0.1°, which together ensure measurements that meet demanding tolerance requirements. These specifications make the instrument suitable for precise layout, alignment and inspection operations where small angular deviations matter. Because the instrument records and transfers angles directly, setup time is reduced and repeated adjustments incur fewer cumulative errors, supporting more efficient and predictable workflows. Clear display and intuitive controls for faster work A large display with display illumination ensures readings remain legible under workshop lighting or in shadowed positions, reducing reading errors and rechecks. The integrated Hold function allows pausing of displayed values while repositioning the arms, and the ability to zero in any arm position simplifies relative measurements and comparative checks. An automatic shut-off after 3 minutes conserves power during intermittent use, while the option to use 4 x AA batteries or rechargeable 1.2 V cells keeps the device ready for on-site tasks with minimal interruption. Stable mounting and practical features for transfer tasks The instrument’s symmetrical 60 cm arms permit easy and stable placement against workpieces and fixtures, aiding accurate angle transfer between templates, machine beds and components. Built-in horizontal and vertical spirit levels support correct plumb and level during positioning, helping to avoid cumulative alignment faults. Durable construction and workshop-oriented functions translate the device’s technical specifications into everyday benefits: fewer setup iterations, clearer handovers between operators and a lower risk of alignment-related scrap. Contact Metav Werkzeuge for personalised advice on integrating the BMI Winkeltronic into workshop workflows or to request detailed technical clarification from the Metav team Technical data Article number: 4000857621NW Type: Winkeltronic Product type: Angle measuring device Brand: BMI Facts Measuring range: 0–355° Resolution: 0.05° Accuracy: ±0.1° Arm length: 60 cm Power supply: 4 x 1.5 V (AA) or 4 x 1.2 V rechargeable cells Auto-off: after 3 minutes Special features Large illuminated display Hold function Zeroing in any arm position Symmetrical arm arrangement for easy contact Integrated horizontal and vertical spirit levels Designed for measuring and transferring angles FAQ How accurate is the Winkeltronic for precision layout work? The Winkeltronic offers a resolution of 0.05° and an accuracy of ±0.1°, providing the precision required for fine alignment and layout tasks in workshop environments. Can the instrument transfer angles directly to a workpiece? Yes. The device is intended for both measuring and transferring angles, aided by its 60 cm symmetrical arms and integrated spirit levels for stable contact. What power options are available for the angle meter? The instrument accepts 4 x 1.5 V AA batteries or 4 x 1.2 V rechargeable cells, allowing flexible power choices depending on workshop preferences. Is the display readable in low-light conditions? The large display includes display illumination so measurements remain legible in shadowed areas or under poor ambient lighting. How does zeroing work on this angle measuring device? The device allows nulling in any arm position, enabling quick relative measurements and simplified comparative checks without complex reorientation. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
60cm Angle Measuring Device 0-180° Range Precision Measurement - NEDO GmbH & Co. KG
Take advantage of the combination of full-range 0–180° measurement, a generous 60 cm leg span and repeatable readings for efficient layout and inspection tasks; order the device via Metav Werkzeuge or contact our consultants for application advice. Winkelfix – Angle measuring instrument with 0–180° range and 60 cm legs (NEDO) The Winkelfix is a rugged angle measuring instrument designed for general workshop and on-site layout tasks, offering a full 0–180° measuring range and long legs for stable alignment. Full-range 0–180° measurement 60 cm leg length for extended reach Clear, repeatable graduations for reliable readings Compact, workshop-ready angle gauge Fast, verifiable angle measurement for production use The device provides a continuous 0–180° scale, which eliminates repeated repositioning and speeds up common alignment and marking operations. The long 60 cm legs increase contact area and stability, leading to repeatable readings and reduced rework. The construction and scale layout prioritise simple verification: the measuring range and graduations are immediately legible, enabling quicker decision-making on the shop floor and fewer measurement steps in the production chain. Practical benefits for assembly, layout and inspection By combining a full-angle range with long legs, the gauge reduces the need for multiple specialised jigs. The design supports fast alignment of components, scribing of reference lines and preliminary checks before machining or welding. These practical advantages translate directly into time savings and lower process variability, which are particularly relevant for production teams and maintenance technicians aiming to keep throughput consistent while maintaining tolerances. Trusted supply and application support from Metav Metav stands for the democratisation of precision: procurement teams benefit from straightforward access to reliable measuring tools and a transparent supply chain out of Emmerich. The distribution approach focuses on dependable availability and application advice, backed by a long-standing customer base and practical spare-part handling. For specialised requirements, Metav’s consultants can advise on integration into existing workflows and on complementary metrology equipment. For accurate angle setting and durable shop-floor performance, request the NEDO Winkelfix via Metav Werkzeuge or consult our specialists at info@metav-werkzeuge.com / +49 2822 7131930 Technical Data Article number: 4000857615NW Product type: Angle measuring instrument Brand: NEDO GmbH & Co. KG Model/Execution: maßxi Facts Measuring range: 0–180° Leg length: 60 cm Packaging unit: 1 UID: 4000857615NW Special features Full-range angle measurement 0–180° Long legs for improved stability (60 cm) Clear graduations for repeatability Suitable for workshop layout and inspection tasks FAQ How precise are readings with this instrument? Readings are reliably repeatable thanks to the clear graduations and the long legs; the Winkelfix is intended for layout and inspection where visual scale reading and stable contact are required. Is the device suitable for on-site construction layout? Yes. The full 0–180° range and 60 cm legs make the instrument well suited to on-site alignment and marking tasks in construction and assembly contexts. Can the gauge replace specialised protractors in the workshop? For general layout, marking and preliminary inspection the angle gauge offers a practical, time-saving alternative; specialised high-precision inspection may still require dedicated metrology tools. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
60mm Adjustable Hair Gauge With Hardened Stainless Steel Hair Edges, DIN 875/0, Supplied In Case - Metav IndustryLine
Combine the adjustable angle function with hardened hairline measuring edges to ensure repeatable squareness checks in production and inspection. Designed to DIN 875/0, this tool supports precise alignment and reliable quality control. Order the Hairline Square directly via Metav Werkzeuge or consult our specialists for application advice. Hairline Square M214.009 — adjustable stainless‑steel precision angle square (DIN 875/0) The Hairline Square M214.009 is an adjustable angle gauge for precise squareness and alignment tasks in workshops and inspection stations. Adjustable angle setting for repeatable checks Hardened hairline measuring edges for fine alignment Conforms to DIN 875/0 for grade 0 accuracy Robust stainless‑steel construction for daily use High‑precision squareness that supports consistent quality control The adjustable angle design delivers controlled alignment for repetitive tasks, reducing set‑up time and measurement variation. Manufactured in stainless steel with hardened hairline measuring edges, the instrument is built to withstand routine workshop use while maintaining its reference geometry. Conformance to DIN 875/0 signals a top accuracy class suitable for inspection benches and final checks, giving clear technical evidence for acceptance criteria and audit trails. Fine optical guidance for exact edge and corner checks The integrated hairline edge acts as a visual datum, allowing sharp optical alignment when inspecting components or setting up fixtures. The slim hairline profile (4 x 4 x 60 mm) provides a narrow reference without obscuring the workpiece, aiding precise positioning. Because the instrument is adjustable, small angular corrections can be made quickly on the bench, improving throughput where numerous identical set‑ups are required. Robust design for workshop and metrology environments A compact grip profile (40 x 23 x 10 mm) ensures secure handling during repeated measurements while the hardened measuring edges protect the reference from premature wear. The combination of durable materials and conformity to an established standard supports a dependable inspection routine and lowers the risk of rework. The tool is ideally suited for mechanical workshops, toolrooms and production inspection where reliable squareness is essential. Contact Metav Werkzeuge for tailored application guidance or to secure the Hairline Square M214.009 from Metav IndustryLine; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M214.009 GTIN: 4054469106038 eClass: 21170127 Customs tariff number: 90178090 Standard: DIN 875/0 Facts Grip dimensions: 40 x 23 x 10 mm Hairline ruler: 4 x 4 x 60 mm SKU: M214.009 Special features Material: stainless steel with hardened hair measuring edges Feature: adjustable Category: angle square Accuracy class: DIN 875/0 FAQ What accuracy class does the tool meet? The Hairline Square M214.009 meets DIN 875/0, indicating grade 0 accuracy suitable for high‑precision squareness checks. How does the hairline edge improve alignment? The hardened hair measuring edges provide a fine visual datum that makes optical alignment and edge‑to‑edge checks more precise with the Hairline Square M214.009. Is the instrument suitable for daily workshop use? Yes, the stainless‑steel construction and hardened measuring edges make the instrument robust enough for routine inspection and workshop environments. Can the angle be adjusted for repeat measurements? The adjustable mechanism allows repeatable angle setting, improving consistency across multiple set‑ups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
60mm Mitre Square Adjustable Handle 40x22x10mm, 60x4x4mm Hair Ruler - TECWERK
Take advantage of precise alignment, an adjustable handle and DIN 875/00 conformity to ensure consistent squareness in assembly and inspection processes; order the precision square directly via Metav Werkzeuge or contact our consultants for technical advice. TECWERK Precision Square — DIN 875/00 adjustable with hairline rule A precision square designed to deliver class-level squareness for workshop and inspection use, featuring an adjustable handle and an integrated hairline rule for fine alignment. DIN 875/00 accuracy class Adjustable handle for tailored positioning Integrated hairline rule 60 x 4 x 4 mm Handle dimensions 40 x 22 x 10 mm Dependable squareness for repeatable results The precision square conforms to DIN 875/00, providing a clear reference for tasks that demand reliable right-angle measurement. Compliance with this standard means the tool is manufactured to tight tolerances, which reduces rework and inspection time by ensuring components meet angular specifications first time. The integrated hairline rule facilitates visual alignment against edges and scribed lines, converting a simple mechanical square into an effective alignment aid for assembly and quality control. Built for practical workshop handling An adjustable handle with dimensions 40 x 22 x 10 mm improves accessibility when working on confined components or complex assemblies. The handle’s adjustability enables fine positional correction without introducing stress to the reference face, preserving the square’s accuracy during repeated use. The compact hairline element of 60 x 4 x 4 mm is sized for clarity without obstructing sightlines, supporting efficient set-up and quicker measurement cycles on the shop floor. What the technical specifications mean in practice The recorded knurl length and ruler dimensions relate directly to how the tool is used: the knurling provides a tactile reference where required, while the hairline rule supplies a precise visual datum for scribing or aligning. Adjustment mechanisms are engineered to retain the reference plane while allowing controlled movement; once set, the position remains stable for inspection runs. These features translate into shorter set-up times and reduced dependency on secondary fixtures for basic right-angle checks. Suitable applications and expected benefits This tool is intended for metrology benches, assembly jigs and inspection routines where quick, repeatable right-angle verification is needed. Typical advantages include faster alignment during component fitting, fewer measurement steps in incoming inspection and a lower likelihood of part rejection due to angular errors. The compact form factor and standard compliance make it a practical addition to both specialist metrology departments and general workshop equipment lists. Contact Metav Werkzeuge for tailored advice on the TECWERK precision square (SKU 2000858415NW) and arrange reliable supply from our Emmerich facility—email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: 2000858415NW Label: Haarwinkel DIN 875/00 Griff-L.40x22x10mm verstellb.TECWERK Product type: Haarwinkel / Precision square Manufacturer: TECWERK Packaging unit: 1 UID: 2000858415NW Numbers / Core technical data Handle dimensions: 40 x 22 x 10 mm Hairline rule: 60 x 4 x 4 mm Knurl length: 0 x 22 x 10 mm Compliance: DIN 875/00 Special features / Versions Adjustable handle (verstellbar) Integrated hairline rule Compact design for workshop use Suitable for inspection and alignment tasks FAQ What level of accuracy does this precision square provide? The TECWERK precision square is produced to DIN 875/00, indicating a high level of geometric accuracy suitable for repeatable right-angle checks in inspection and assembly. Is the handle position adjustable and stable during use? Yes, the tool features an adjustable handle (40 x 22 x 10 mm) that permits fine positioning and is designed to maintain stability once set for inspection runs. Can the hairline rule be used for scribing and visual alignment? The included hairline rule (60 x 4 x 4 mm) serves as a visual datum for scribing and precise edge alignment on parts and fixtures when using the TECWERK precision square. Which environments and users benefit most from this tool? Metrology departments, maintenance workshops and assembly technicians will find the square useful for quick, repeatable angular checks and set-ups where standard-compliant references are required. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
60×120cm Angle Measuring Device 0-270° Range, Long Legs - STABILA
Take advantage of the combination of a wide 0–270° measuring range and long 60 x 120 cm arms for efficient inspection of large components; the robust STABILA design supports consistent, repeatable angle checks. Order the WINKELSTAR directly via Metav Werkzeuge or consult our specialists for precise application advice. WINKELSTAR angle measuring device by STABILA — 0–270° range, 60 x 120 cm arms The WINKELSTAR is an angle measuring device for workshop and site use, built to check and set angles up to 270° on large components with long, rigid arms. 0–270° measuring range for wide angle checks 60 x 120 cm rigid arms for large workpieces STABILA build for stability and repeatability Faster inspection of large parts through an extended measuring range The combination of a 0–270° measuring range and long arm length significantly reduces the need to reposition components during inspection. This increases throughput in production and repair workflows by limiting setup time and potential handling errors. The extended range enables checks beyond a simple flat or right-angle measurement, which is particularly useful when working on complex assemblies or irregular geometries. The clear numeric span simplifies planning of sequential checks and supports a rational measurement routine in small and medium-sized workshops. Stable construction for repeatable results and fewer rechecks A rigid arm geometry and purpose-built angle mechanism provide stability and consistent contact with the workpiece, which translates into improved repeatability across successive measurements. Repeatable setups reduce scrap and rework and support quality control documentation. For teams that integrate angle verification into production steps, the sturdy configuration helps maintain alignment under modest handling, ensuring a reliable baseline for further machining or assembly tasks without introducing excessive measurement uncertainty. Designed to integrate into workshop metrology workflows The instrument suits carpentry, metalworking and general maintenance contexts where larger parts require quick, reliable angle verification. Supplied as a single unit, it can be stored with minimal fuss and incorporated into existing inspection routines. Clear labelling and straightforward geometry make it easy for trained staff to include angular checks in final inspection processes, helping to avoid assembly errors and ensuring components meet design intent. For procurement, the device is a practical choice when the emphasis is on efficient angle control and consistent results. Contact Metav Werkzeuge for tailored advice on integration and to secure a STABILA WINKELSTAR directly from our Emmerich facility on the Rhine Technical Data SKU: 4000857625NW Type: WINKELSTAR Product: Winkelmessgerät Brand: STABILA Label: Winkelmessgerät WINKELSTAR Messber.0-270Grad Schenkel-L.60x120cm BMI Facts Measuring range: 0–270° Arm dimensions: 60 x 120 cm Packaging unit: 1 Special features Large-range angle measurement Long, rigid arms for large workpieces Identifier: 4000857625NW Additional reference: 0-270: 4000 857 630 FAQ What angles can be measured with this instrument? The device covers a 0–270° range, enabling checks from flat to obtuse angles without frequent repositioning. What are the arm dimensions of the angle gauge? The gauge features arms of 60 x 120 cm, suitable for larger components and assemblies. Is the instrument intended for workshop use on large components? Yes; the long, rigid arms and wide measuring range make the product suitable for measuring and setting angles on larger workpieces typically found in workshops. How is the product identified for ordering or inventory? The item is listed under SKU 4000857625NW and does carry the label information shown in the product data. How is the device supplied? The product is supplied as a single unit (packaging unit: 1), ready for integration into existing inspection routines. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
630x400x63mm Granite Square 90° Grade 0, DIN 875/0 - Metav IndustryLine
Combine DIN 875/0 level accuracy with a massive, vibration-damping granite body and expansive measuring faces to ensure reliable 90° verification in production and inspection. Order the granite square directly via Metav Werkzeuge or consult our specialists for application-specific advice. Granite Square 90° (Grade 0) — 630 x 400 x 63 mm, DIN 875/0 | Metav IndustryLine A Granite Square 90° (Grade 0) designed for high-precision verification of machine spindles, fixtures and workpieces in metrology and workshop quality control. Grade 0 accuracy to DIN 875/0 Solid granite construction for thermal stability Precision-ground 630 x 400 x 63 mm faces 40 kg mass for vibration damping during checks Consistent right-angle reference for production inspection This reference square offers a repeatable right-angle datum suitable for machine shops and inspection benches where reproducibility matters. Built and finished to DIN 875/0, the instrument provides a high confidence level for go/no-go decisions in daily quality control. The large, precision-ground faces minimise the need for repositioning and reduce handling time, supporting faster, standardised inspection routines and lowering the risk of misleading measurements caused by unstable fixturing. Granite body for thermal and mechanical stability Made from natural granite, the component combines density and low thermal expansion to keep the measuring faces stable during routine use. The substantial 40 kg mass absorbs ambient vibration and makes the square a reliable reference when checking spindles, machine tooling or larger workpieces. Because granite is inherently wear-resistant and resists corrosion, the square maintains its geometry over long service intervals, which supports consistent measurement outcomes and reduces recalibration frequency. Designed for workshop integration and practical use With dimensions of 630 x 400 x 63 mm, the square balances reach and rigidity for use on inspection tables and against machine beds. The broad faces facilitate clear contact with workpieces and accessories, simplifying the alignment of fixtures and the verification of perpendicularity. The compact footprint compared with longer bars keeps handling manageable while offering sufficient area for most medium-format components, helping to speed up set-up and verification tasks without sacrificing precision. For dependable right-angle verification, choose the Metav IndustryLine granite square and contact Metav Werkzeuge in Emmerich for tailored delivery options and technical clarification — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M214.608 GTIN: 4054469109442 Label: Granite square 90° Grade 0 Manufacturer: Metav IndustryLine Facts Dimensions: 630 x 400 x 63 mm Weight: 40 kg Standard: DIN 875/0 Tariff number: 68022300 Special features Material: Granite Grade: 0 accuracy Application: Right-angle verification of spindles and workpieces Category: Angle squares / Metrology FAQ What degree of accuracy does this square provide? The granite square is finished to DIN 875/0, indicating Grade 0 accuracy suitable for high-precision right-angle verification. Is the square suitable for machine spindle alignment and workpiece checks? Yes — the design and the precision faces make the square ideal for spindle alignment and checking perpendicularity of fixtures and components. What are the physical dimensions and weight of the instrument? The faces measure 630 x 400 x 63 mm and the unit weighs 40 kg, which provides good stability and vibration damping during checks. Does the product include a calibration certificate? No calibration standard is specified in the provided product data, so a calibration certificate is not listed with this item. What material is used and what are the benefits? The body is made from granite, chosen for its low thermal expansion, wear resistance and natural damping properties that support reproducible measurements. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
70 x 200 mm Angle Column 90° Ground Base and Shaft, Accuracy 0.005 mm - Metav IndustryLine
Take advantage of the combination of 0.005 mm accuracy, a hardened special steel construction and a ground reference face for consistently reproducible right‑angle setups; order the component directly via Metav Werkzeuge or consult our technical advisors for application support. M214.622 Angle Reference Column — 90° precision, 70 x 200 mm The M214.622 angle reference column is a 90° reference component for workshop and inspection use, designed to provide a stable, high‑precision datum for angular measurement and alignment tasks. 90° ground reference face 0.005 mm high accuracy Hardened special steel construction Stable 7 kg mass for damping Reduce inspection time with true metrology precision The column serves as a compact angle reference that replaces improvised setups and reduces repositioning. With a certified 0.005 mm accuracy, the device establishes a clearly defined right‑angle datum that shortens setup times and lowers scrap rates. The geometry — 70 x 200 mm — is sized to give a sensible balance between reach and rigidity, making it suitable for bench inspection or integration into gauge fixtures. This level of precision supports consistent part acceptance criteria and streamlined quality control. Built for repeatable use and industrial handling Constructed from hardened special steel, the reference block resists wear and retains its surface integrity during repeated clamping and handling. Both the base and the mantle have been ground, producing flat, true faces that promote repeatable registration against workpieces or reference plates. The substantial 7 kg mass reduces the influence of incidental vibration, so measurement uncertainty is dominated by the instrument, not the environment. These attributes translate into fewer rechecks and a dependable reference for routine shop‑floor use. Integrates cleanly into inspection workflows The right‑angle reference is compact enough for bench use yet robust for workshop demands; it integrates with height gauges, dial gauges and coordinate equipment as a stable datum. The combination of ground faces and precise squareness supports comparative checks, alignment tasks and fixture verification. The component’s design reduces fixturing complexity: instead of fabricating bespoke stands, existing gauges can be referenced to the block, improving throughput and lowering fixturing cost. The unit is a practical investment for production lines and maintenance rigs seeking repeatable alignment. Contact Metav Werkzeuge today to request a technical quote or specification sheet for the M214.622 angle reference column from Metav IndustryLine and to discuss suitability for specific inspection tasks Technical data Article number: M214.622 GTIN: 4054469183794 Manufacturer: Metav IndustryLine Facts Dimensions: 70 x 200 mm Accuracy: 0.005 mm Weight: 7 kg Special features Hardened special steel, heat treated Stand face and mantle surface ground 90° reference geometry for angular alignment Category: Angle reference FAQ What applications is this reference column suited for? The M214.622 angle reference column is intended for angular inspection, fixture alignment and comparative checks where a stable 90° datum is required. How does the 0.005 mm accuracy affect daily use? An accuracy of 0.005 mm means the reference column offers high confidence for tolerance checks and reduces rework caused by imprecise setup when using the Metav IndustryLine component. Can the block be used on a shop floor? Yes; the hardened special steel and ground faces make the column suitable for workshop environments where repeated handling and light fixture contact occur. Is the M214.622 compatible with height gauges and dial indicators? The column’s ground faces and standardised geometry allow straightforward referencing with height gauges, dial indicators and comparator fixtures. What maintenance is required to keep accuracy? Regular cleaning and careful handling of the ground faces will preserve the column’s performance; periodic verification against certified standards is recommended. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
700x300 Carpenter's Square Stainless Steel With Mm Scale And Scriber Holes, Powder Coated - Metav IndustryLine
Take advantage of a corrosion-resistant stainless steel body and a precise millimetre scale with 5 mm scribe holes for reliable site layout. Combine a stable 35 x 1.2 mm profile with lightweight handling for efficient marking and measuring. Order the M214.931 carpenter's square directly via Metav Werkzeuge or ask our consultants if needed. M214.931 Carpenter's square — 700 x 300 mm, stainless, powder-coated M214.931 is a robust framing square designed for accurate layout and marking in carpentry, joinery and general site use. Seamless stainless steel construction Yellow powder-coating for corrosion resistance Millimetre scale with 5 mm scribe holes Stable 35 x 1.2 mm profile for consistent results Durable construction for demanding sites The square is formed from seamless stainless steel, finished with a yellow powder-coating that reduces corrosion and keeps graduations legible for longer. The continuous profile prevents weak spots that can appear with welded joints, so the tool maintains its geometry under regular on-site use. A profile of 35 x 1.2 mm provides a favourable stiffness-to-weight ratio, limiting flex during marking and helping to deliver repeatable right-angle checks across repetitive tasks. Precise layout and fast marking Equipped with a clear millimetre scale and regularly spaced scribe holes every 5 mm, this framing square speeds up transfer and layout operations. The perforations allow direct scribing through the blade, which simplifies repetitive marking on timber or sheet materials and reduces back-and-forth measurement. With overall dimensions of 700 x 300 mm, the tool covers common framing and cladding tasks while keeping edges accessible for interior and external layouts. Practical handling and workshop reliability At approximately 0.45 kg the tool is light enough for single-person handling yet solid enough to remain stable during use; this supports efficient work flow without compromising accuracy. The bright finish improves visibility on both pale and dark surfaces, helping users maintain alignment under varied lighting. Designed for craftsmen who value durability and speed, the square suits framing, joinery, stair work and general workshop layout where a dependable right angle and clear marking are required. Choose the Metav IndustryLine M214.931 for durable, accurate marking and layout — contact Metav Werkzeuge to arrange purchase or technical advice via info@metav-werkzeuge.com or +49 2822 7131930. Technical data Article number: M214.931 GTIN: 4054469183480 Manufacturer: Metav IndustryLine Facts Dimensions: 700 x 300 mm Cross-section: 35 x 1.2 mm Weight: 0.45 kg Special features Material: stainless steel, seamless, yellow powder-coated Millimetre scale with scribe holes every 5 mm Corrosion-resistant finish FAQ What material is the square made from and how durable is the finish? The blade is manufactured from seamless stainless steel and is powder-coated in yellow for enhanced corrosion resistance and long-term legibility. Can the scribe holes be used directly for marking timber? Yes. The scribe holes are spaced every 5 mm to allow direct scribing through the blade, enabling quick and repeatable layout lines on wood and sheet materials. Is the size suitable for standard framing and cladding tasks? With overall dimensions of 700 x 300 mm the tool covers common framing, cladding and stair layout requirements while remaining manageable for single-person use. How does the cross-section affect performance? The 35 x 1.2 mm profile offers a balanced stiffness that reduces flex during marking, supporting consistent right-angle checks and repeatable measurements across multiple pieces. Is this square useful in both workshop and on-site environments? Yes. The combination of corrosion-resistant finish, clear millimetre graduations and a stable profile makes it suitable for workshop layout and on-site carpentry or joinery tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
700x300 mm Carpenter's Square Stainless Seamless 35x1.2 mm With Mm Scale, No Punch Holes - Metav IndustryLine
Benefit from the combination of seamless stainless-steel construction, a clear millimetre scale and a rigid 35 x 1.2 mm cross-section for dependable large-format layout work; order via Metav Werkzeuge or consult our specialists for application advice. Carpenter's square M214.911 – 700 x 300 mm, seamless stainless steel (Metav IndustryLine) The Carpenter's square M214.911 is a large-format layout square for framing, joinery and workshop layout tasks, combining a continuous millimetre scale with a stiff cross-section for repeatable measurements. Seamless stainless steel for long-term durability Millimetre scale engraved for clear layout Robust 35 x 1.2 mm cross-section reduces flex Large 700 x 300 mm format for framing tasks Engineered for precise, repeatable large-format layout The square is manufactured from seamless stainless steel, providing a straight, corrosion-resistant reference that keeps measurements reliable over time. Its millimetre scale is integrated along the edge to support quick, traceable marking and ensures layout accuracy across the larger arm. The cross-section of 35 x 1.2 mm increases torsional stiffness compared with thin-sheet competitors, reducing deflection when aligning long edges; this is especially beneficial for framing, roofing and metal fabrication where consistent right angles matter. The combination of material and profile delivers precision and durability without adding unnecessary weight. Practical handling for busy workshops and sites With a 700 x 300 mm format the square balances reach and manageability: the long arm covers sizeable layout spans while the shorter arm remains easy to seat against workpieces. The tool’s overall mass of 0.45 kg gives sufficient heft for stable positioning without becoming awkward to handle on ladders or at awkward angles. The product is supplied without scribe holes, preserving a continuous straight edge for marking and protecting against moisture ingress points; this keeps the reference edge true and reduces contamination. The smooth edges and robust profile make the square a practical choice for everyday use in joinery, carpentry and plate work. Designed for professional workflows and reliable supply As part of the Metav IndustryLine, this layout square is aimed at workshops that require dependable, repeatable tools rather than frequent replacement. The stainless construction minimises maintenance, while the clear millimetre graduation speeds up layout tasks and reduces rework — a direct contribution to shop-floor efficiency. For procurement teams the M214.911 is a straightforward specification item: robust material, fixed dimensional format and a rigid cross-section that supports consistent measurement procedures. Combined with Metav’s distribution and quality filter in Emmerich, the square is positioned as a practical, professional tool for everyday measurement tasks. Contact Metav Werkzeuge for purchasing advice and reliable supply from Emmerich; call +49 2822 7131930 or email info@metav-werkzeuge.com to discuss suitability for specific workshop applications Technical data Article number: M214.911 GTIN: 4054469183404 Material: seamless stainless steel Dimensions: 700 x 300 mm Cross-section: 35 x 1.2 mm Weight: 0.45 kg Special: millimetre scale; without scribe holes Facts Long arm length: 700 mm Short arm length: 300 mm Cross-section width x thickness: 35 x 1.2 mm Mass: 0.45 kg Special features Seamless stainless steel construction Millimetre scale engraved No scribe holes for a continuous edge Straight, durable reference for layout FAQ What material is the square made from and why does it matter? The square is made from seamless stainless steel, which provides corrosion resistance and a stable straight edge; the material choice keeps the reference accurate over prolonged use. Is the millimetre scale suitable for workshop layout and marking? Yes, the integrated millimetre scale on the M214.911 supports clear, repeatable marking and speeds up layout work in carpentry and metal fabrication. How does the 35 x 1.2 mm cross-section affect performance? The 35 x 1.2 mm profile increases rigidity and reduces flex along the long arm, improving angle stability for larger framing and layout tasks. Why are there no scribe holes and what is the benefit? The absence of scribe holes preserves a continuous straight edge for marking and reduces potential points for corrosion, giving a cleaner, more reliable reference. Which applications are best suited to this format? The 700 x 300 mm format is ideal for framing, joinery, cabinetmaking and general workshop layout where a large, stable right-angle reference is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
700x300 mm Carpenter's Square With Holes 35x1.2 mm Stainless Steel With mm Scale, Holes Every 5 mm - Metav IndustryLine
Take advantage of a seamless stainless-steel construction with a clear millimetre scale and evenly spaced scribing holes every 5 mm to speed up layout work and ensure reproducible marks; order directly via Metav Werkzeuge or consult their specialists for application advice. Carpenter's square M214.921 – Metav IndustryLine stainless, 700 × 300 mm with 5 mm scribing holes A carpenter's square M214.921 designed for precise marking and angle checks in timber and light metalwork, featuring a millimetre graduation and a rigid 35 × 1.2 mm profile. Seamless stainless steel construction Millimetre scale for clear layout Scribing holes every 5 mm for repeat marks Robust 35 × 1.2 mm profile, 700 × 300 mm Faster, more reliable layout for production tasks A rigid layout tool such as this square reduces rework by providing a stable reference for repetitive marking tasks. The 700 × 300 mm format combines reach with manageable handling for framing and component work, while the 35 × 1.2 mm profile contributes to torsional stiffness so lines stay true during transfer. The millimetre scale printed along the blade simplifies immediate measurement and layout without the need for separate rulers, improving throughput on the shop floor and speeding up cycle times for repetitive operations. Corrosion resistance and longevity on site Made from seamless stainless steel, the square resists corrosion in humid or outdoor environments and keeps its straightness through long-term use. For workshops that alternate between wet and dry conditions, the material choice reduces maintenance intervals and replacement costs. The seamless fabrication also avoids crevices where dirt or moisture could collect, supporting consistent performance and a longer service life in both joinery and light metalworking settings. Practical features that cut marking time Equipped with scribing holes every 5 mm, the square enables rapid, repeatable transfer marks for stair stringers, stud layouts or patterned cuts without measuring each time. The evenly spaced holes work with scribing tangs or awls to transfer datum lines quickly and accurately. Combined with the millimetre graduation, this arrangement turns a single tool into both a straightedge and a repetitive marking jig, saving setup time and reducing secondary operations on the bench. Workshop-ready design that fits existing workflows The tool’s balanced weight (approx. 0.45 kg) and open frame make it easy to position and align on workpieces while still providing the mass needed for stable marking. The combination of stainless construction, a clear mm scale and multiple scribing points makes the product a suitable choice for on-site carpentry as well as for use in a dedicated workshop. Integration into existing kits is straightforward: the square complements common layout processes and is rugged enough for daily use. Contact Metav Werkzeuge to secure the Metav IndustryLine carpenter's square M214.921 or to discuss which layout tools best match production requirements Technical data Article number: M214.921 GTIN: 4054469183442 Manufacturer: Metav IndustryLine Facts Dimensions: 700 × 300 mm Cross-section: 35 × 1.2 mm Weight: 0.45 kg Special features Material: stainless steel, seamless Millimetre scale Scribing holes every 5 mm Category: angle / square (Winkel) FAQ What materials is this square suited for? The carpenter's square M214.921 is made from seamless stainless steel, making it suitable for timber and light metal layout tasks where corrosion resistance and durability are needed. How are the scribing holes arranged and used? Scribing holes are spaced every 5 mm, providing quick datum transfer for repeat marks; they work with awls or scribing pins to speed up repetitive layout work. Is the scale metric and easy to read on site? Yes, the tool features a clear millimetre scale along the blade to facilitate immediate measurement and marking without extra instruments. Which SKU should be referenced when ordering? Reference SKU M214.921 and the Metav IndustryLine designation when enquiring to ensure the correct 700 × 300 mm, 35 × 1.2 mm configuration is supplied. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
700x300mm Carpenter Square Stainless Steel Laser-Scaled No Scribing Holes - TECWERK
Benefit from the combination of stainless steel durability, a laser‑etched mm scale and the generous 700×300 mm L‑shape for precise large‑format layout and repeatable marking. Order the carpenter's square directly via Metav Werkzeuge or ask the consultants for tailored advice. Carpenter's square L 700×300 mm — stainless steel L‑square with laser‑etched mm scale (TECWERK) A Carpenter's square L 700×300 mm engineered for accurate right‑angle marking and layout tasks in woodworking and general workshop applications. Stainless steel construction for corrosion resistance Laser-etched mm scale for durable, precise readings L-shaped 700×300 mm for large-format layout work Supplied without scribing holes for a continuous edge Durable material for reliable right‑angle accuracy Constructed from stainless steel, this L‑square delivers stable performance in workshop environments where occasional moisture or heavy use would degrade lesser materials. The robust metal body reduces the risk of distortion over time, maintaining the critical 90° relationship between the legs. Combined with the 700×300 mm leg format, the tool supports larger boards and panels without flex, promoting consistent accuracy across repeated layout operations and reducing the need for frequent readjustment. Laser‑etched millimetre scale for long‑lasting legibility The laser‑etched mm scale ensures measurements remain readable even after extended use; unlike painted graduations, the marking will not flake or wear off. Laser etching produces a fine, high‑contrast graduation that enables quick, unambiguous readings at the layout stage, improving workflow efficiency. For operators who value repeatable setups, the permanent scale contributes directly to time savings and fewer measurement errors on production runs. Practical L‑shape geometry optimised for workshop tasks The L‑shaped geometry with a long and short leg is designed for versatile layout: the longer leg provides an extended reference edge for straight cuts and framing, while the shorter leg allows access in tighter positions. The tool is supplied without scribing holes, resulting in a continuous straight edge that is ideal for pencil marking or for running along a guide. This configuration suits joinery, cabinet making and light metal layout where an uninterrupted datum edge is preferable. Simple integration into daily workshop routines This L‑square is suitable for carpenters, joiners and general workshop technicians who require a straightforward, rugged layout instrument. The combination of a corrosion‑resistant material and a durable engraved scale reduces downtime and maintenance, helping to keep projects on schedule. If additional technical data or application guidance is needed for a specific task, Metav Werkzeuge can provide expert advice and clarifications to ensure the tool matches the intended production use. For reliable layout and marking, choose the TECWERK stainless steel L‑square and contact Metav Werkzeuge for purchase advice or specifications—info@metav-werkzeuge.com • +49 2822 7131930. Technical data Article number: 2000858529NW Description: Carpenter's square L 700×300 mm, stainless steel, laser‑etched mm scale, without scribing holes Manufacturer: TECWERK Packaging unit: 1 Dimensions and numerical data Leg dimensions: 700×300 mm Scale division: millimetre Packaging unit: 1 UID: 2000858529NW Materials and features Stainless steel Laser‑etched mm scale Without scribing holes L‑shaped configuration FAQ Is the square suitable for outdoor use? The stainless steel construction improves resistance to moisture and outdoor conditions; the TECWERK L‑square with laser‑etched scale is therefore better suited to workshops and sheltered outdoor use than plain steel versions. How accurate is the scale on the tool? The laser‑etched millimetre graduation provides precise and durable markings, ensuring repeatable measurements for layout and marking tasks with the 700×300 mm L‑square (SKU 2000858529NW). Can the continuous edge be used with scribers? Yes, the edge supplied without scribing holes offers an uninterrupted datum for pencil or scribe marking and for use as a straight guide during transfers. Which trades benefit most from this L‑square? Joinery, carpentry and general workshop operations gain the most from the large‑format reference edge and robust stainless steel construction of this TECWERK L‑square. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
700x300mm Carpenter Square With Scribing Holes, Stainless Steel Laser-Engraved Scale - TECWERK
Combine the stainless steel construction with the laser‑etched mm graduations and precise scribing holes for dependable, repeatable layout work — order the tool directly via Metav Werkzeuge or consult our advisors for application guidance. TECWERK Carpenter's L‑Square 700 x 300 mm — stainless steel, laser‑etched mm scale A TECWERK Carpenter's L‑Square 700 x 300 mm designed for precise marking, squaring and layout tasks in carpentry and general workshop use. Robust stainless steel body Laser-etched mm graduations Scribing holes for exact marking 700 x 300 mm L-shaped legs Accurate layout and marking for faster assembly The L‑shaped layout tool delivers precision marking across long and short legs, enabling consistent right‑angle checks and transfer marks on timber, sheet materials and metal. The clear mm graduations, produced by laser etching, remain legible under heavy workshop use, so measurements are repeatable and layout errors are reduced. This reliability supports smoother assembly processes and fewer trial fits, which improves overall shop productivity. Built for durability and dependable readings Made from stainless steel, the profile resists corrosion and maintains flatness over time, contributing to long‑term durability on the bench. The laser‑etched mm scale is not a printed finish; it is a permanent mark that resists abrasion and solvent exposure, ensuring that the scale stays accurate even after prolonged use. The robust L profile also provides a stable reference edge for scribing and clamping, reducing measurement drift and rework in everyday tasks. Practical features that speed up workshop tasks Integrated scribing holes allow rapid transfer of marks using a scribe or awl, making repetitive layout operations quicker and more precise. The combination of a long and short leg in a single tool eliminates the need to switch gauges for many jobs, saving handling time and reducing the chance of alignment errors. Suitable for joiners, site carpenters and workshop technicians, this L‑square supports efficient marking, cutting and assembly workflows while offering the consistent performance expected from professional tools. For further technical information or specific application advice, Metav Werkzeuge can provide additional data and guidance. Contact Metav Werkzeuge for tailored advice or to place an order for the TECWERK Carpenter's L‑Square 700 x 300 mm — available directly from Metav Werkzeuge, Emmerich. Technical data Article number: 2000858531NW Brand: TECWERK Designation: Carpenter's L‑square 700 x 300 mm, with scribing holes Numbers Legs: 700 x 300 mm Packaging unit: 1 UID: 2000858531NW Special features Stainless steel construction Laser‑etched mm graduations Scribing holes for layout marking L‑shaped profile FAQ What materials is this L‑square suitable for? The TECWERK Carpenter's L‑Square 700 x 300 mm is suitable for timber, sheet materials and light metal layout; the stainless steel profile provides a stable reference for marking. How do the scribing holes improve marking accuracy? Scribing holes enable direct transfer of points using a scribe or awl, so marks are positioned precisely on the workpiece when using the L‑square. Will the scale remain readable after heavy use? Yes — the laser‑etched mm graduations on the L‑square are permanent and resist abrasion, ensuring long‑term legibility under workshop conditions. Is the profile resistant to corrosion? The robust stainless steel construction offers corrosion resistance, helping to preserve flatness and measurement accuracy over time. Can this tool be used for on‑site carpentry and bench work? The 700 x 300 mm L profile is versatile for both on‑site and workshop tasks, providing a reliable right‑angle reference for layout and cutting. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
70mm 100mm Centre Angle L-Arm 90mm Cross Section, Precision Steel - TECWERK
Take advantage of the combination of L-shaped geometry, precise leg dimensions (100 × 70 mm) and a 90 mm cross-section for a stable centring reference — order through Metav Werkzeuge or consult the technical advisors for application support. L-shaped Centring Angle 100 × 70 mm — TECWERK, 90 mm cross-section The L-shaped Centring Angle 100 × 70 mm by TECWERK provides a compact reference aid for alignment and fixture setup in workshop and production environments. L-shaped geometry for stable referencing Leg lengths 100 × 70 mm for adaptable set-ups 90 mm cross-section for increased rigidity Single unit packaging for immediate use Reliable geometry for precise referencing The L-shaped geometry establishes two perpendicular reference faces that simplify the alignment of workpieces during fixturing and inspection. With leg lengths of 100 × 70 mm and a 90 mm cross-section, the device supplies a clear physical datum for centring tasks and quick comparative measurements. The design reduces setup time by providing a repeatable mechanical reference, which supports efficient processes and consistent results in routine workshop use. Practical use in clamping and centring operations Designed as a compact centring aid, this angle is suited to positioning, visual alignment and supporting small fixtures. The right-angled legs create an obvious datum plane and a lateral surface for checks against jaws, stops or straight edges. The simple form factor means compatibility with common clamping accessories and bench setups, enabling accurate orientation without complex tooling — a pragmatic solution where fast, reliable alignment is required. How the dimensions translate into performance The specified dimensions — 100 × 70 mm legs and a 90 mm cross-section — contribute to stability and resistance to tipping or flex under light handling. The larger cross-section improves the mechanical behaviour of the reference during repeated use, helping to preserve the flatness of the datum faces and supporting repeatable alignment results. For precision-oriented tasks, the defined geometry offers a tangible benefit over improvised reference aids. Support and integration into workshop workflows Metav Werkzeuge provides technical guidance for integrating centring angles into measurement and fixturing routines. Advice is available on pairing the angle with clamps, parallels or vice jaws, and on simple checks to verify datum integrity before use. For bespoke integration or clarifications about suitability in specific applications, Metav Werkzeuge can supply additional information and advice by email or phone. Contact Metav Werkzeuge for application advice on TECWERK centring angles and to arrange procurement — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 2000858031NW Label: Zentrierwinkel Schenkel-L.100x 70mm TECWERK Product type: Centring angle Brand: TECWERK Packaging unit: 1 Facts Cross-section: 90 mm Leg lengths (L-shaped): 100 × 70 mm Special features L-shaped geometry for centring and referencing Single-piece unit SKU: 2000858031NW FAQ What is the primary application for this centring angle? The centring angle is intended as a reference aid for alignment, fixture set-up and comparative positioning in workshop and production environments. Which dimensions define the datum faces? The datum is formed by the two legs with 100 × 70 mm lengths and a 90 mm cross-section giving stable reference faces. Is the product supplied ready to use? Yes, the item is supplied as a single unit and ready for immediate integration into bench and clamping setups. Can this angle be used with standard bench vices and clamps? The L-shaped geometry is compatible with common clamping accessories and vice jaws for positioning and support during set-up operations. How can further technical questions be addressed? Technical queries can be directed to Metav Werkzeuge; product identification: TECWERK centring angle, SKU 2000858031NW. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
75 x 50mm Angle Bracket With Stop, 15 x 4mm Cross-Section - TECWERK
Take advantage of a compact, repeatable measuring aid that combines a lightweight aluminium construction with a stable 15 x 4 mm cross-section for reliable layout and inspection tasks; order the TECWERK L-angle directly via Metav Werkzeuge or consult our advisers for application support. TECWERK L-angle 75 x 50 mm (with stop) — precision aluminium angle for workshop layout TECWERK L-angle 75 x 50 mm (with stop) is a compact L-shaped angle in aluminium, designed for accurate edge referencing and repeatable positioning in general workshop and maintenance tasks. Robust aluminium L-angle, corrosion-resistant Legs 75 x 50 mm for clear reference edges Integrated stop for repeatable positioning Cross-section 15 x 4 mm for dimensional stability Reliable, repeatable positioning for routine layout and inspection The compact L-angle, with leg lengths of 75 x 50 mm, offers a stable reference for marking, checking squareness and quick setup tasks. The integrated stop guarantees repeatable positioning, which reduces setup time and minimises cumulative error during repetitive operations. Because the cross-section is 15 x 4 mm, the tool resists bending under light manual pressure, enabling consistent alignment on small parts or fixtures. This makes it suitable for everyday workshop checks, quality control samples and fast assembly tasks where reproducible results are required. Lightweight aluminium construction that keeps handling efficient Constructed from aluminium, the angle combines lightweight handling with sufficient structural stiffness for routine workshop use. The material choice reduces fatigue during frequent hand-held checks and speeds up inspection cycles, while being naturally corrosion-resistant for longer service life in standard shop environments. The modest mass also supports quick repositioning on benches and machines, improving workflow efficiency during setup phases and iterative adjustments. Practical integration: where this compact angle proves its value The design with an integrated stop is particularly helpful when consistent edge-to-edge measurements or repeated references are needed, for example in joinery checks, small-part assembly and fixture alignment. The compact footprint suits congested workstations and portable inspection kits; the 15 x 4 mm cross-section ensures the angle maintains its geometry during normal handling. For workshops seeking a simple, durable reference tool, this aluminium L-angle is straightforward to include in quality routines and jigs without extensive adaptation. For reliable, repeatable layout work, choose the TECWERK L-angle and contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 for tailored advice and prompt dispatch from Emmerich. Technical Data Article number: 2000858067NW Label: Winkel Schenkel-L.75x50mm m.Anschlag Alu.TECWERK Product type: Angle Execution: with stop Facts Cross-section: 15 x 4 mm Legs: 75 x 50 mm Packaging unit: 1 UID: 2000858067NW Special features Material: aluminium Integrated stop for repeatable positioning Manufacturer: TECWERK FAQ What applications is this angle suitable for? This aluminium L-angle is suitable for workshop layout, small-part inspection and fixture alignment where a compact, repeatable reference is required. Does the angle provide repeatable positioning? Yes, the integrated stop ensures repeatable positioning, which helps to reduce setup time and improve consistency during repetitive checks with the TECWERK L-angle. Is the tool robust enough for daily workshop use? The 15 x 4 mm cross-section and aluminium construction provide sufficient stiffness and corrosion resistance for everyday workshop handling and routine inspection tasks. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
75 x 50mm Angle Plate Without Stop, 15 x 5mm Section - TECWERK
Take advantage of a compact reference tool with a 75 x 50 mm leg format and a 15 x 5 mm cross-section for stable positioning; the execution without stop ensures unobstructed alignment in layout and inspection tasks. Order directly via Metav Werkzeuge or consult the technical team for specification checks. TECWERK Angle DIN 875/I – Legs 75 x 50 mm, without stop TECWERK Angle DIN 875/I offers a precision reference for workshop layout and squaring tasks, designed for straightforward alignment in industrial and craft applications. DIN 875/I accuracy class Legs 75 x 50 mm for versatile marking Cross-section 15 x 5 mm for stable support Without stop for unobstructed alignment Precise reference for consistent layout and squaring A compact precision angle built to the DIN 875/I standard provides a reliable reference edge for marking and squaring operations. Thanks to the 75 x 50 mm leg geometry, the tool supplies a defined working face that reduces guesswork during setup and inspection. This results in fewer rework cycles and steadier production throughput, as the consistent reference improves process repeatability and supports efficient quality control. Stable profile for everyday workshop use The 15 x 5 mm cross-section delivers mechanical stability while keeping the profile slim for easy handling and storage. The version without stop allows unobstructed access to corners and edges, making the device suitable for a range of layout tasks where a fixed stop would impede positioning. The compact design combines usability with a robust feel for routine use on benches and trolleys in busy shops. Integrates into inspection and process workflows As a basic squaring and layout implement, this angle slots into inspection benches and measuring routines with minimal adaptation, providing a quick visual and tactile reference. The simple form factor supports fast checks and short setup times, contributing to smoother workflows. For further technical data or specific application advice, Metav Werkzeuge is available to assist with detailed requirements and compatibility questions. For precise squaring work using the DIN 875/I specification, contact Metav Werkzeuge for ordering and expert advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: 2000858443NW Article: Angle DIN 875/I, legs 75 x 50 mm Product type: Angle Brand: TECWERK Execution: without stop Facts Leg lengths: 75 x 50 mm Cross-section: 15 x 5 mm Packaging unit: 1 UID: 2000858443NW Special features DIN 875/I accuracy class No stop for unobstructed alignment Stable profile for layout and squaring FAQ What standard does this angle conform to? The TECWERK Angle DIN 875/I (SKU 2000858443NW) conforms to the DIN 875/I specification and is intended as a precision reference for layout and squaring tasks. What are the dimensions of the legs and profile? Leg lengths are 75 x 50 mm and the cross-section is 15 x 5 mm, giving the angle a compact but stable profile suitable for workshop use. Does this version include a stop for positioning? The supplied execution is without stop, providing an unobstructed edge for alignment and marking where a fixed stop would be restrictive. Can this angle be integrated into inspection setups? Yes, the compact geometry and DIN 875/I reference make the angle suitable for simple inspection benches and quick visual checks in production workflows. Who to contact for more technical details or compatibility checks? For detailed inquiries regarding the TECWERK Angle DIN 875/I (SKU 2000858443NW), Metav Werkzeuge offers technical support and ordering assistance. TECWERK: Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
750 x 375 mm Angle Plate Without Stop, 50 x 9 mm Cross-Section - TECWERK
Take advantage of the combination of long-legged format and a solid cross-section for reliable right-angle checks on large workpieces; the design without a stop allows flexible fixturing and integration into inspection workflows. Order the item directly via Metav Werkzeuge or consult the Metav team for technical guidance. TECWERK Engineer's Square DIN 875/II – Legs 750 x 375 mm, without stop TECWERK Engineer's Square DIN 875/II – Legs 750 x 375 mm, without stop is a precision workshop square designed for verifying right angles on large-format components and assemblies in production and inspection settings. Engineered to DIN 875/II accuracy Legs 750 x 375 mm for large workpieces Solid cross-section 50 x 9 mm Supplied without stop for flexible mounting Accurate right-angle verification for large components The DIN 875/II classification denotes a recognised level of accuracy for workshop squares; this standardised tolerance supports consistent, repeatable checks during incoming inspection and assembly tasks. With leg dimensions of 750 x 375 mm, this tool allows alignment and squareness control across extended edges and large plates, reducing the need for repeated repositioning. The substantial 50 x 9 mm cross-section ensures geometric stability during measurement, which translates into fewer setup iterations and more efficient quality checks on the shop floor. Flexible mounting and stable support for varied workflows Supplied without a stop, the square offers adaptable fixturing options: it can be clamped, bolted or used with magnetic fixtures where appropriate, enabling customised setups for different workpieces. The open design supports straightforward clamping to surface plates or machine beds, so the tool integrates smoothly into production jigs and inspection rigs. The robust geometry of the legs provides a reliable datum for layout, marking-out and assembly verification tasks, improving throughput by simplifying handling of large components. Practical integration into quality control processes As a precision layout instrument, the square complements surface plates, height gauges and other inspection equipment to form a coherent metrology routine. The long legs and clean geometry make it suitable for use in workshop inspection, fixture checking and straightness references on fabricated assemblies. Specification conformity to DIN 875/II helps maintain traceable workflows and supports communication of tolerance expectations across purchasing, production and quality teams. For additional technical details or compatibility questions, Metav Werkzeuge provides advisory support via e-mail or telephone. Contact Metav Werkzeuge for personalised advice on using the TECWERK engineer's square in production or inspection, or request a quotation and delivery options from our Emmerich team. Technical data Article number: 2000858275NW Label: Winkel DIN 875/II Schenkel-L.750x375mm o.Anschlag TECWERK Manufacturer: TECWERK Facts Legs (L x W): 750 x 375 mm Cross-section: 50 x 9 mm Packaging unit: 1 Special features Execution: without stop Standard: DIN 875/II FAQ What level of accuracy does this square provide? The TECWERK engineer's square conforms to DIN 875/II, indicating accuracy suitable for standard workshop inspection and layout tasks where grade II tolerances are required. Can the square be clamped or fixed to a surface plate? Yes. Supplied without a stop, the square is intended for flexible mounting and can be clamped or secured to a surface plate or fixture to form a stable datum for measurements. For which tasks is the long-legged design most useful? The extended 750 x 375 mm legs are ideal for checking squareness on large panels, welded assemblies and large-format components where shorter squares would require repositioning. Does the cross-section contribute to measurement stability? The 50 x 9 mm cross-section provides structural rigidity, reducing flex during handling and ensuring consistent right-angle reference during layout and inspection. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
750 x 375 mm Fabrication Square Flat Galvanised, Flat Face, Factory Standard - Metav IndustryLine
Take advantage of a flat, galvanised special‑steel construction and generous 750 x 375 mm leg length for stable, repeatable right‑angle layout. The robust profile and workshop‑grade finish deliver long service life and reliable marking edges. Order the fabrication square directly via Metav Werkzeuge or consult the technical team for application advice. Fabrication Square M214.511 – Flat galvanised special‑steel angle, 750 x 375 mm (Metav IndustryLine) Fabrication Square M214.511 is a flat, galvanised workshop angle designed for precise right‑angle layout, marking and assembly tasks in metalworking and fabrication. Flat galvanised special‑steel construction Large 750 x 375 mm legs for big parts Workshop‑grade accuracy and durability Ideal for layout, marking and assembly Stable reference edge for accurate layout and marking The heavy‑duty, flat galvanised profile provides a low‑warp reference that keeps edges true when laying out or scribing large components. With special steel construction and a generous leg length of 750 x 375 mm, the tool offers an extended straight edge that reduces flex during handling, which translates into fewer reworks and faster set‑ups on the shop floor. The combination of a stable profile and corrosion‑resistant finish supports repeatable right‑angle checks across fabrication, welding fixtures and assembly jigs. Designed for workshop durability and practical use A simple, resilient design makes this square suitable for daily use in demanding environments. The flat profile sits flush against faces for reliable marking, while the galvanised coating protects the surface from routine wear and rust—helping to preserve the right‑angle reference over time. The square’s dimensions allow layout of larger plates and frames without sacrificing manoeuvrability, and the manageable weight supports single‑operator handling on bench or floor work. Clear specification and maintenance guidance Specified to Werksnorm and finished galvanised, the square requires minimal upkeep: wipe clean after use, avoid prolonged exposure to corrosive media, and store flat to retain straightness. The robust material choice makes it a pragmatic tool rather than a laboratory instrument—optimised for workshop‑grade accuracy where reliable, repeatable squaring and marking are essential to production flow. Traceability is supported by catalogue identifiers for procurement and stock control. Choose the Metav IndustryLine fabrication square for durable, straight‑edge layout control and contact Metav Werkzeuge in Emmerich for availability or specification support on +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M214.511 GTIN: 4054469108988 Tariff code: 90178090 Manufacturer: Metav IndustryLine Core data Dimensions: 750 x 375 mm Weight: 2 kg Finish: Galvanised Special features Material: Special steel, galvanised Design: Flat profile for stable reference edge Standard: Werksnorm FAQ What materials is this fabrication square suitable for? The Fabrication Square M214.511 is made from special steel with a galvanised finish, making it suitable for typical metalworking tasks such as steel plate and structural fabrication. How should the square be stored to maintain accuracy? Store the Fabrication Square M214.511 flat and dry after cleaning; avoid stacking heavy items on top to preserve the straight reference edge. Is the finish corrosion‑resistant for workshop use? Yes, the galvanised coating on the Fabrication Square M214.511 provides practical corrosion resistance for general workshop environments. Can this square be used for welding set‑ups and fixture alignment? The flat profile and long legs of the Fabrication Square M214.511 make it well suited to layout, marking and preliminary alignment tasks in welding and fixture work. Does the product comply with any formal standard? The square is produced to Werksnorm, indicating factory specification and quality control appropriate for workshop equipment. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
750 x 375mm Angle Plate With Stop, 50 x 9mm Section - TECWERK
Made for reliable layout and inspection tasks, this angle delivers DIN 875/II accuracy with long legs and a robust cross-section; the integrated stop enables repeatable positioning on large components. Order the TECWERK angle directly via Metav Werkzeuge or consult the Metav team for application guidance and additional technical data. Precision Engineer's Square DIN 875/II — TECWERK, 750 x 375 mm legs (with stop) This Precision Engineer's Square DIN 875/II is designed for accurate workshop layout and inspection, featuring long 750 x 375 mm legs and an integrated stop for repeatable measurements Precision to DIN 875/II accuracy Long legs 750 x 375 mm for large layouts Robust 50 x 9 mm cross-section Integrated stop for repeatable positioning Accurate layout on large workpieces The long leg combination of 750 x 375 mm provides a stable reference for marking and checking larger assemblies, reducing the need for secondary fixturing. Thanks to the DIN 875/II tolerance class, the square offers a defined angular deviation useful in inspection routines and alignment tasks; this measurable standard supports quality assurance procedures and traceable results. The long legs plus a 50 x 9 mm section reduce flex under light contact, which improves the repeatability of layout operations and minimises rework. Built for durability and workshop use A solid cross-section of 50 x 9 mm combines rigidity with manageable weight for regular handling on the shop floor. The construction is intended for everyday industrial use: the profile resists minor knocks and preserves squareness over time, helping to keep maintenance intervals low. The integrated stop gives a physical reference for repeated measurements, speeding up process cycles and reducing time spent re-clamping or re-aligning components. Practical benefits for inspection and assembly Using a calibrated engineer's square in DIN 875/II class simplifies conformity checks against drawing tolerances and supports incoming inspection or in-process control. The prominent leg lengths make it suitable for layout on sheet metal, welded frames and fixtures, where a longer datum reduces measurement uncertainty. The tool's repeatability contributes directly to process efficiency and lowers scrap rates by catching angular deviations early. Integration into workshop workflows The design suits machinists, fitters and quality technicians who require a dependable, manual reference for squareness. Where precision layout must be combined with throughput, the square’s long legs and repeatable stop help streamline tasks such as marking, aligning jigs and verifying right angles on assemblies. For users seeking clear, verifiable results, the square supports routine checks and helps document consistency across shifts and operators. Contact Metav Werkzeuge for procurement or application advice on the TECWERK precision square — technical consultants are available by phone or e‑mail to discuss suitability for specific materials and processes Technical Data Article number: 2000858375NW Facts Leg lengths: 750 x 375 mm Cross-section: 50 x 9 mm Packaging unit: 1 Special features Product type: Angle (engineer's square) Execution: with stop Standard: DIN 875/II Manufacturer: TECWERK FAQ What tolerance class does the square meet? The square conforms to DIN 875/II, which defines the permissible angular deviation for this class of precision engineer's squares. Is the angle suitable for layout on large frames? Yes, the long 750 x 375 mm legs and robust cross-section make the tool suitable for marking and checking larger frames and sheet assemblies. Does the square allow repeatable measurements? The integrated stop provides a fixed physical reference for repeatable positioning and faster inspection cycles. Manufacturer/Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
750 x 375mm Fitting Square Without Stop, 30 x 5mm Cross-Section - TECWERK
Take advantage of a large-format layout tool that combines a robust L-shaped profile with clear dimensional reach for reliably squaring and marking oversized workpieces; the combination of legs 750 x 375 mm and a 30 x 5 mm cross-section ensures stable alignment in fabrication and workshop tasks. Order via Metav Werkzeuge or consult our specialists for technical guidance. TECWERK Engineer's Square – L-legs 750 x 375 mm (no stop) The TECWERK engineer's square is a heavy-duty L-shaped layout instrument designed for marking and checking right angles on large components in metalworking and general workshop environments, supplied without an integrated stop for flexible positioning. Large L-shaped layout, stable and rigid Legs 750 x 375 mm for extended reach 30 x 5 mm rectangular cross-section Supplied without stop for flexible positioning Reach and accuracy for large-format marking The elongated legs 750 x 375 mm provide extended reach for sheet material, plates and framed parts, enabling precise transfer of right angles across larger assemblies. Thanks to the extended leg lengths, measurements and scribing can be executed without repeated repositioning, which reduces cumulative error and speeds up layout work. The long-armed design is particularly useful where a single verified reference edge is used to square multiple items, supporting consistent part preparation and repeatable workmanship on the shop floor. Rigid profile for repeatable squaring A 30 x 5 mm rectangular cross-section gives the tool a stiff, non-twisting profile that supports repeatable alignment when squaring or inspecting components. This sectional geometry minimises flex under light loading and maintains a straight reference edge for marking and visual inspection. For workshops that require reliable mechanical aids rather than consumable guides, the stable profile reduces the need for constant rechecking and promotes a faster, more predictable workflow when laying out right angles. Flexible handling without a stop for adaptable setup Supplied without a stop, the square offers unobstructed placement along edges and across corners, allowing bespoke clamping and fixture solutions when a fixed stop would restrict positioning. The absence of an integrated stop permits direct contact with irregular surfaces and facilitates positioning against bespoke jigs or temporary fixtures. Operators benefit from the simplicity of an unobstructed L-profile when aligning awkward geometries or when using auxiliary stops and clamps to create custom datum arrangements. Choose the TECWERK engineer's square for dependable large-scale layout and contact Metav Werkzeuge for availability and application advice from our Emmerich hub Technical data Article number: 2000858075NW Label: Schlosserwinkel Schenkel-L.750x375mm o.Anschlag TECWERK Product type: Schlosserwinkel Manufacturer: TECWERK SKU / UID: 2000858075NW Facts Leg dimensions: 750 x 375 mm Cross-section: 30 x 5 mm Packaging unit: 1 Special features L-shaped layout square Supplied without stop (ohne Anschlag) Suitable for workshop marking and squaring applications FAQ What are the exact leg lengths of the square? The TECWERK engineer's square features legs of 750 x 375 mm, providing extended reach for large-format marking and alignment. Is the square supplied with an integrated stop? No, the tool is supplied without a stop, allowing flexible placement and the use of external clamps or datum blocks for bespoke fixtures. How does the cross-section affect performance? The 30 x 5 mm rectangular cross-section increases rigidity and reduces twisting, which supports repeatable squaring and more reliable reference edges during layout tasks. Can the square be used for both metal and woodworking layout? The L-profile is designed for general workshop layout and checking of right angles; suitability for specific materials depends on the application and handling methods employed. Where can further technical information be obtained? Detailed application advice and availability are provided by Metav Werkzeuge, who can assist with selection for particular workshop requirements. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
750 x 375mm Machinist Square With Stop, 30 x 5mm Cross-Section - TECWERK
Take advantage of a sturdy L‑leg profile and an integrated stop to speed up layout, marking and right‑angle checks while keeping repeatability high. With the 750 x 375 mm legs and a compact 30 x 5 mm cross‑section, this square offers a clear balance of reach and rigidity. Order the item directly via Metav Werkzeuge or contact the consultants for application advice. Engineer's Square L‑leg 750 x 375 mm with stop by TECWERK The Engineer's Square L‑leg 750 x 375 mm with stop is a precision L‑square designed for layout, marking and setup tasks in metalworking and fabrication. Robust L‑shape profile Integrated stop for repeatable positioning Large legs 750 x 375 mm for extended reach Consistent 30 x 5 mm cross‑section for stiffness Accuracy where it matters on the shop floor The solid L‑leg geometry of this layout tool delivers dependable right‑angle references across larger workpieces. The long leg of **750 x 375 mmlegs provide extended reach for plates and frames, while the compact 30 x 5 mm cross‑section contributes to dimensional stability under routine handling. For workshop operatives and setup technicians, the result is fewer alignment iterations and reduced marking errors, which translates into more consistent downstream machining and welding outcomes. The device functions as a simple, direct way to control squareness during layout without relying on laser systems or complex fixturing. Faster, repeatable setups with an integrated stop An integrated stop permits repeatable positioning and helps standardise measurement routines. In practical terms, the stop acts as a fixed datum against which parts are held; this reduces the need for repeated clamping adjustments and cuts setup time on recurring tasks. For teams executing batch work or repeated assembly checks, the stop supports consistent part placement and makes transfer measurements quicker. Where traceability and reproducibility matter, this physical end‑stop is a pragmatic solution that improves workflow efficiency without adding electronic components. Designed for workshop durability and handling The L‑square’s form factor is optimised for everyday workshop use: the length combination ensures access into larger assemblies while keeping the tool manageable during transport between benches. The balanced leg dimensions provide a compromise between reach and rigidity, enabling reliable contact with edges and faces. Operatives will appreciate the predictable behaviour of a compact cross‑section when aligning parts or verifying right angles, especially during welding preparation and mechanical assembly. This tool is tailored for fabrication, maintenance and general metal‑working tasks where robust manual measuring aids remain essential. Practical integration into workshop routines This layout square integrates easily into standard marking and inspection setups. It complements common hand tools and measuring aids, serving as a straightforward reference for scribers, centre punches and clamping fixtures. Routine upkeep is minimal: a clean, dry surface and simple storage prevent damage and preserve the accuracy of faces and edges. For any uncertainty about fit or application in a specific process, technical advice is available to ensure the tool matches the intended tasks, particularly where larger format squaring is needed. For precision layout and reliable repeatability, specify the TECWERK L‑leg square via Metav Werkzeuge—contact Metav Werkzeuge for application guidance and supply from Emmerich. Technical data Article number: 2000858175NW SKU: 2000858175NW Label: Schlosserwinkel Schenkel‑L.750x375mm m.Anschlag TECWERK Dimensions & core data Legs: 750 x 375 mm Cross‑section: 30 x 5 mm Packaging unit: 1 Features & design L‑leg square with stop Product type: Engineer's square Brand: TECWERK FAQ What is the primary use of this L‑leg engineer's square? The square is intended for layout, marking and right‑angle checks in metalworking and fabrication; the integrated stop supports repeatable positioning during batch work. Can the tool be used for welding layout on large plates? Yes, the leg combination of 750 x 375 mm makes the square suitable for welding preparation and plate layout where extended reach is required. How does the integrated stop improve workflows? The stop provides a fixed datum for repeatable part placement, reducing setup time and improving consistency across repeated operations. Is the product identified by a specific SKU or article number? The item is listed under article number/SKU 2000858175NW for ordering and stock reference. Manufacturer / Responsible: NORDWEST Handel AG; Robert‑Schuman‑Straße 17; 44263 Dortmund
750x375 mm Machinist Square With Stop, Zinc Plated Special Steel, Works Standard - Metav IndustryLine
Take advantage of the combination of a galvanised, special‑steel construction, a built‑in stop for repeatable positioning and the generous 750 × 375 mm working face to speed up layout and alignment tasks; order directly via Metav Werkzeuge or consult the Metav team for application advice. Machinist's square M214.531 — Machinist's square, 750 × 375 mm, galvanised with stop (Metav IndustryLine) The Machinist's square M214.531 is a heavy‑duty angle tool intended for alignment, scribing and simple setting tasks in metalworking and fabrication environments. Heavy-duty galvanised special steel construction Built-in stop for repeatable positioning Size 750 × 375 mm for large components Factory-standard accuracy and robust finish Precise alignment across a large working face The large 750 × 375 mm face provides a stable reference for bigger assemblies while remaining manageable for one- or two-person handling. Constructed from special steel with a galvanised finish, the tool combines rigidity with corrosion resistance so that squaring and scribing remain consistent over time. The enlarged faces reduce deflection when pressing the square against plates or profiles, delivering reliable results for alignment and basic inspection tasks without requiring specialised fixturing. Repeatable positioning for efficient workflow A built‑in stop allows for quick, repeatable location of parts and jigs, reducing cycle time during repetitive marking or setup operations. The square’s mass of 3.2 kg contributes to stable contact and helps prevent movement during scribes or clamp‑on operations. Delivered to factory standard, the tool offers a predictable reference under normal workshop conditions and is suitable where robust, straightforward accuracy is required for day‑to‑day production and maintenance work. Durable finish and workshop suitability The galvanised coating protects the working faces and edges from workshop wear and environmental effects, extending service life and lowering lifecycle costs compared with untreated steels. The design suits common metalworking tasks such as marking, assembly alignment and basic welding set‑up. Its combination of robust construction and practical features makes it a dependable option for machine shops, maintenance departments and tradespeople who need a solid angle reference without unnecessary complexity. For dependable layout and repeatable setup choose the Metav IndustryLine Machinist's square M214.531 — contact Metav Werkzeuge in Emmerich for delivery information or technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data SKU: M214.531 GTIN: 4054469109091 Manufacturer: Metav IndustryLine Material: Special steel, galvanised Feature: With stop Facts Dimensions: 750 × 375 mm Weight: 3.2 kg Tariff number: 90178090 Special features Factory standard (Werksnorm) Corrosion‑resistant galvanised finish Intended use: alignment, marking and simple setting tasks Category: Angle (Winkel) FAQ What tasks is this square best suited to? The M214.531 machinist's square is intended for alignment, scribing and basic setting tasks in metalworking and fabrication where a large, stable reference face is required. Does the square require special maintenance to retain accuracy? Routine cleaning and protection of the galvanised faces are sufficient; avoid heavy knocks and store the square flat to preserve the factory‑standard reference surface. Is the stop adjustable or fixed? The built‑in stop is provided to enable repeatable positioning for workshop tasks; the square M214.531 from Metav IndustryLine is configured for robust, repeatable use in fabrication and maintenance settings. Which materials is the square suitable for working with? The M214.531 is a layout and alignment tool for metalworking applications and is commonly used on steel, aluminium and other workshop materials during marking, assembly and set‑up. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75cm Angle Measuring Device 0.05° Resolution 0.1° Accuracy IP65 - BMI
Take advantage of precise angle transfer, a clear illuminated display and a robust 75 cm arm length to speed up layout and assembly tasks; order directly via Metav Werkzeuge or contact their consultants for technical advice. Winkeltronic angle gauge 0–355° — 75 cm arms, 0.1° accuracy A Winkeltronic angle measuring device for accurate measuring and transferring of angles in workshops and industrial layout work. Precise 0.05° resolution and ±0.1° accuracy Large illuminated display for clear readings Symmetrical 75 cm arms for easy placement Integrated horizontal and vertical spirit levels Precision that keeps production on target Highly exact measurement values minimise rework and improve assembly repeatability. The 0.05° resolution paired with a stated ±0.1° accuracy provides a reliable basis for alignment and angular transfer tasks in fabrication and maintenance. Where tight tolerances matter, the fine resolution reduces interpretation errors and shortens inspection cycles, which contributes directly to consistent throughput and fewer adjustments on subsequent operations. Designed for straightforward positioning and readout A clear, large display with display illumination ensures readings remain legible in dim workshops or on-site environments, reducing eye strain and misreads. The device’s symmetrical arms (75 cm) simplify contact with workpieces and enable stable positioning; the built-in horizontal and vertical spirit levels help maintain plumb and level while taking or transferring an angle. These features combine to make angle measurement faster and more dependable during assembly, layout and set-up tasks. Practical operation for everyday workshop use Operational convenience reduces downtime: the digital meter includes a hold functionand auto power-off after three minutes , and allows zeroing in any arm position, which aids repeated measurements and comparative checks. Power is supplied by four AA cells (1.5 V) or rechargeable AA cells (1.2 V), ensuring easy replacement and compatibility with common workshop batteries. The broad 0–355° range covers nearly a full circle, making the instrument versatile for most angular measurement requirements. Contact Metav Werkzeuge to discuss how the Winkeltronic angle gauge can integrate into current workflows and to arrange delivery or technical consultation — Metav Werkzeuge provides expert advice from Emmerich and reliable supply across Europe (info@metav-werkzeuge.com, +49 2822 7131930) Technical data SKU: 4000857639NW Type: Winkeltronic Product: Angle measuring device Measuring range: 0–355° Arm length: 75 cm Packaging unit: 1 UID: 4000857639NW Facts Resolution: 0.05° Accuracy: ±0.1° Power supply: 4 × 1.5 V AA or 4 × 1.2 V rechargeable AA Automatic shut-off: after 3 minutes Measuring range numeric: 0–355° Special features Large illuminated display Hold function Zeroing in any arm position Symmetrical arm arrangement for easy placement Integrated horizontal and vertical spirit levels Suitable for measuring and transferring angles FAQ What measuring range does the instrument cover? The measuring range is 0–355° for the Winkeltronic angle gauge (SKU 4000857639NW), allowing nearly full-circle measurements for most workshop tasks. How precise is the angle reading on this device? The device offers a 0.05° resolution with an accuracy of ±0.1°, giving highly precise readings suitable for layout and alignment work. Can the angle reading be locked for transfer? Yes, the unit includes a hold function so readings can be frozen and transferred without losing the measured value. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75x50 mm Angle Plate With Stop, Hardened Stainless Steel, DIN 875/1 - Metav IndustryLine
Take advantage of a compact right‑angle reference that combines hardened stainless steel construction with DIN‑level accuracy for reliable setup and inspection tasks. The small footprint and integrated stop ensure fast positioning and repeatable squaring; order the component directly via Metav Werkzeuge or consult our specialists for application advice. Stop square 75 × 50 mm, DIN 875/1 — hardened stainless‑steel right‑angle reference (Metav IndustryLine) The Stop square 75 × 50 mm is a compact hardened stainless‑steel right‑angle reference designed for workshop layout, inspection, and fixture set‑up where accurate squaring and a positive stop are required. DIN 875/1 accuracy class Hardened stainless‑steel construction Compact 75 × 50 mm for confined spaces Consistent squareness for fast inspection and setup The small right‑angle reference offers a reliable datum for rapid checks and setup operations. Made from hardened stainless steel, the item resists wear and maintains its measuring faces under frequent use, supporting long‑term precision. Conformance to DIN 875/1 signals a defined tolerance band for squareness, which simplifies documentation and quality routines in manufacturing or maintenance environments. This makes the tool suitable as a repeatable reference for short‑run inspections and assembly alignment. Space‑saving design with an integrated stop for repeatable positioning With a 75 × 50 mm footprint and a built‑in stop, the device enables quick, reproducible positioning against edges and workpieces. Its compact form factor is particularly useful where sovereign clearance is limited or multiple inspection points must be addressed in rapid succession. The positive stop reduces setup time by holding the part in a consistent position, thereby improving throughput without adding complexity to clamping or fixturing operations. Corrosion resistance and low maintenance for everyday workshop use The stainless construction provides inherent corrosion resistance, reducing the need for frequent surface care in humid or oily shop environments. Thanks to the hardened finish, the reference faces sustain contact‑induced wear and prolong the interval between reconditioning. Routine cleaning and occasional light lubrication of contact zones will preserve accuracy and surface condition, supporting dependable service life and stable measuring performance. For application support or to reserve the Metav IndustryLine stop square (SKU M214.333) for your next project, contact Metav Werkzeuge in Emmerich by phone or e‑mail for tailored advice and fast dispatch. Technical Data Article number: M214.333 GTIN: 4054469108179 Manufacturer: Metav IndustryLine Material: hardened stainless steel Standard: DIN 875/1 Dimensions & core data Dimensions: 75 x 50 mm Tariff code: 90178090 ECLASS: 21170119 Features & finish With stop for repeatable positioning Hardened measuring faces Compact right‑angle reference for workshop use Label: Anschlagwinkel 75x50 mm, DIN 875/1, INOX FAQ What level of accuracy does this square provide? The stop square meets the DIN 875/1 criterion for right‑angle references, offering a defined tolerance suitable for workshop inspection and many production controls. Is the material suitable for humid workshop environments? Yes — the tool is made from hardened stainless steel, which provides enhanced corrosion resistance for everyday workshop conditions. Can the stop square be used for layout and fixture setup? The compact 75 × 50 mm size and integrated stop make it well suited for layout tasks, fixture alignment and repeatable positioning in confined areas. How is the item identified for ordering or inventory? The product is listed under SKU M214.333 and GTIN 4054469108179 for procurement and stock management. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
75x50 mm Angle Stop With Stop, DIN 875/2, Normal Steel - Metav IndustryLine
Benefit from defined squareness, a compact 75 x 50 mm footprint and robust carbon steel construction for reliable setup and repeatable positioning. Order the angle square directly via Metav Werkzeuge or ask our consultants if needed. Metav IndustryLine Angle square M214.572 — Engineer's square, 75 x 50 mm (DIN 875/2) A Metav IndustryLine Angle square 75 x 50 mm (DIN 875/2) for precise squaring and fixture setting in metalworking, inspection and assembly operations DIN 875/2 accuracy class Compact 75 x 50 mm format Solid carbon steel construction Integrated stop for secure seating Precision where alignment matters The small-format engineer's square delivers reproducible right angles for setup and inspection tasks. Built to DIN 875/2, the gauge provides a defined tolerance band for squareness that supports routine workshop control and machine setup. The compact 75 x 50 mm face keeps deflection low while enabling quick placement against workpieces; this makes it suitable for short runs, jigs and detailed machining operations. The defined standard ensures compatibility with inspection routines and simplifies acceptance criteria in production documentation. Durable construction for everyday use Constructed from carbon steel, the tool combines rigidity with long-term wear resistance. The solid material and machined faces maintain geometry under normal workshop loads, reducing the need for frequent reconditioning. A positive mechanical stop is incorporated to ensure the square seats consistently against a reference surface, which reduces variations when transferring layout lines or checking perpendicularity. The finish and material choice favour a balance between robustness and cost-efficiency for everyday industrial use. Practical benefits for the workshop The compact format and robust build accelerate setup times and reduce rework: a clearly defined squaring reference shortens alignment procedures at machines and in assembly jigs. The square is easy to handle and store; its small footprint suits bench work and tight fixturing environments. Where repeatability matters, the combination of standardised tolerances and a secure seating stop makes the tool a reliable companion for repetitive tasks, quality checks and first-article inspection. Specification and compliance in the supply chain Supplied under the Metav IndustryLine designation and identified as SKU M214.572, the gauge fits established quality processes and traceability practices. Identification via GTIN and classification codes facilitates inventory management and purchasing in industrial supply chains. The product is a pragmatic choice when a standard-compliant squaring reference is required without the complexity of larger angle plates or dedicated metrology fixtures. Contact Metav Werkzeuge for a detailed suitability check and secure this Metav IndustryLine square for consistent workshop alignment tasks Technical data Article number: M214.572 GTIN: 4054469109244 eCl@ss: 21170119 Facts Dimensions: 75 x 50 mm Standard: DIN 875/2 Tariff number: 90178090 Special features Material: Normalstahl (carbon steel) With stop for secure seating Category: Winkel (measuring angle) FAQ What is the intended use of this angle square? The angle square (Metav IndustryLine Angle square 75 x 50 mm, DIN 875/2) is intended for checking and setting right angles during assembly, fixture setup and routine inspection tasks. How does DIN 875/2 affect accuracy? DIN 875/2 specifies the tolerance class for squareness; the Angle square 75 x 50 mm is manufactured to that class to ensure consistent and documented angular accuracy for workshop use. Is the square suitable for use on a machine table? Yes, the compact format and integrated stop allow the square to be used for quick checks and fixturing on machine tables, particularly where a small, rigid reference is required. What material is used and how does that influence durability? The square is made from carbon steel (Normalstahl), which provides a sturdy, wear-resistant face that maintains geometry under normal workshop conditions. Which identifiers should be used for procurement and stock control? Use SKU M214.572 and GTIN 4054469109244 for ordering and inventory; the eCl@ss 21170119 supports catalogue classification. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Ensure right angles every time with precision angle gauges
Angle measurement is decisive in metalworking, where even the smallest deviation from a 90° geometry can cause assembly errors or functional faults. The category covers both fixed verification tools and variable measuring instruments, presented here as angle gauges, with common synonyms control squares and sine bars used throughout.
Where and how these tools make the difference on the shop floor
For basic layout and rough alignment, the engineer’s square (a simple flat or bench square) serves as the workshop baseline; it is useful for marking and quick checks but not intended for precision components. When higher accuracy is required, control squares with hardened and lapped faces are used; they are produced in accuracy classes referenced by DIN 875 and designed for the light gap method, which reveals form errors by inspecting the gap between gauge and workpiece under illumination. In pipeline and vessel fabrication, the flange square provides a robust contact geometry to align flanged faces to pipe axes and to withstand high mechanical loading. For angles other than 90°, a sine bar enables trigonometrical determination by using end measures, achieving resolutions into the seconds of arc when set up correctly. Regular calibration and checks for wear and flatness of the legs are essential, since a rounded or damaged leg will distort results.
Practical advantages that reduce rework and speed production
- Reduced fitting errors through repeatable reference geometry using control squares.
- Clear detection of form errors with the light gap method (fast visual indication).
- Durable contact surfaces thanks to hardened and lapped faces, extending service life.
- Accurate non-90° measurement via sine bar setups, enabling fine angular adjustments.
- Stable alignment of flanged components with purpose-built flange squares, lowering assembly time.
Why Metav is the reliable partner for precision angle measurement
Metav stands for democratisation of precision. As an experienced precision partner, Metav combines decades of know-how with a comprehensive range for industry, craft and trade; over 48,000 customers trust this quality filter based in Emmerich. With a broad assortment and consistent supply, Metav simplifies procurement and ensures a dependable source for angle gauges, calibration accessories and workshop standards.
Quick summary
Accurate angle gauges — from basic engineer’s squares to high-precision control squares and sine bars — prevent costly fit problems and support reliable, repeatable manufacture. Choose tools matched to the required accuracy class and maintain them regularly to keep measurement integrity.
FAQ
What is the difference between an engineer’s square and a control square?
An engineer’s square is a workshop baseline for marking and rough checks, while a control square features hardened and lapped faces and is manufactured to tighter tolerances (per DIN 875) for inspection and detection of form errors.
How does the light gap method work for checking right angles?
The light gap method places the workpiece against a control square; uneven gaps visible under a light source indicate deviations from perpendicularity, providing an immediate visual assessment of form errors.
When should I use a sine bar instead of a fixed angle gauge?
Use a sine bar when you need precise angles other than 90°. By stacking end measures you set the desired angle trigonometrically, achieving much finer resolution than most fixed gauges allow.
How often should angle gauges be checked for wear?
Regular inspection of flatness and leg condition is mandatory; any rounding or damage to the legs can significantly falsify measurements, so schedule checks according to usage intensity and your quality control procedures.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com