Precision gauge blocks and plug gauges for reliable dimensional control
Mechanical gauge blocks and plug gauges are essential for tactile verification of threads, bores and gap dimensions, providing fast, unambiguous go/no-go results that enhance process reliability and reduce scrap. Designed for industrial metalworking and toolmaking, these precision tools support incoming inspection and final quality checks by delivering traceable measurements in applications such as thread inspection, bore diameter testing and spacing checks. Manufactured from specially hardened, low-distortion alloys and fine-lapped for minimal measurement uncertainty, the range includes thread plug gauges, precision plug gauges and calibration gauge blocks to ensure long-term repeatability and wear resistance.
M13 x 0.75 Three-Point Thread Go Ring, Right-Hand, Hardened Gauge Steel, DIN 13 6g - Metav IndustryLine
Reliable thread acceptance for fine-pitch assemblies is achieved through hardened gauge steel and DIN‑aligned tolerances; benefit from consistent Go verification and reduced rework. Order the thread ring gauge directly via Metav Werkzeuge or ask our consultants if needed. Thread ring gauge M13 x 0.75 (Go) — ring gauge, DIN 13, 6g — Metav IndustryLine Thread ring gauge M13 x 0.75 (Go) is a right‑hand ring gauge designed to verify conformity of metric ISO fine threads in production and incoming inspection. Go ring gauge for M13 x 0.75 metric fine thread Hardened gauge steel for lasting dimensional stability Conforms to DIN 13 tolerance class 6g Right‑hand thread verification for process control Ensure correct fit for fine‑pitch assemblies The Go ring gauge provides a fast, objective check that an M13 x 0.75 internal thread meets the specified form and size. By allowing only parts that pass the gauging plane, the gauge simplifies go/no‑go decisions at the inspection station and shortens cycle time for quality control. Constructed from hardened gauge steel, the tool resists wear and preserves a stable reference diameter, which supports repeatable acceptance testing and reduces scrap through reliable conformity checks. Built to DIN standards for predictable tolerances Compliance with DIN 13 and the 6g tolerance class means the gauge references an established interchangeability standard; this provides traceable limits that can be integrated into documented inspection plans. The nominal designation M13 x 0.75 identifies the thread diameter and pitch, while the right‑hand orientation matches common production threads. For manufacturers and inspection labs, this standardised approach enables consistent decisions across shifts and sites, improving throughput and minimizing measurement disputes. Practical advantages in workshop and production use The compact ring form factor facilitates rapid handling at control benches and assembly lines, so thread verification becomes a seamless step in the workflow rather than a bottleneck. The hardened gauge steel construction preserves calibration between checks; when combined with a clear part‑handling routine, the gauge helps maintain a stable quality baseline. Lightweight at 0.13 kg, the ring is easy to place and remove without compromising stiffness, delivering practical benefits where speed and accuracy matter most. Traceability and identification for quality records The ring is supplied with clear identification data (SKU and GTIN) suitable for process documentation and inventory control, supporting traceability across production batches. Using a dedicated ring gauge for M13 x 0.75 threads reduces ambiguity during audits and supports root‑cause analysis when nonconforming threads are found. Integrating the gauge into a documented inspection sequence helps demonstrate controlled measurement procedures and consistent application of the DIN 13 standard. Specify the Metav IndustryLine thread ring gauge for reliable M13 x 0.75 verification — contact Metav Werkzeuge in Emmerich for delivery options and technical advice Technical Data Article number: M315.113.3 GTIN: 4054469124049 SKU: M315.113.3 Thread: M13 x 0.75 Weight: 0.13 kg Orientation: Right‑hand Facts Pitch: 0.75 mm Diameter class: M13 Tolerance class: 6g Standard: DIN 13 Special features Go ring gauge for metric ISO fine threads Material: gauge steel, hardened Category: gauges / ring gauges Suitable for process and incoming inspection Compact, workshop‑friendly form FAQ What does the Go specification mean for this ring gauge? The Go designation indicates the ring checks whether an internal thread meets the maximum material condition; the thread ring gauge M13 x 0.75 (Go) from Metav IndustryLine confirms acceptance when the part passes fully onto the gauge. Can this gauge be used for both production and incoming inspection? Yes. The Metav IndustryLine ring gauge is designed for routine checks in production and receiving inspection to ensure M13 x 0.75 threads conform to DIN 13, 6g. How should the gauge be stored to preserve accuracy? Store the ring gauge in a dry, dust‑free environment and protect it from impact; using a dedicated storage tray or labelled compartment helps maintain the hardened reference surface and ease traceability for SKU M315.113.3. Does the ring gauge indicate if a thread is oversize or undersize? The Go ring gauge confirms whether a thread meets the acceptance limit; if the part does not pass the gauge, it indicates the thread is outside the permitted size or form and requires further inspection. Is the material resistant to wear during frequent use? Yes. The gauge is manufactured from hardened gauge steel, which provides high resistance to abrasion and maintains dimensional stability under repeated gauging cycles. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M13x0.75 Thread Go Ring Metric ISO Fine Right-Hand DIN 13, 6g Hardened Gauge Steel - Metav IndustryLine
Take advantage of the combination of DIN 13 conformity, hardened gauge steel and a compact 0.08 kg mass to secure reproducible thread checks in production. The ring serves as a clear reference for quality assessment of metric fine threads and supports efficient inspection routines. Order the thread ring gauge directly via Metav Werkzeuge or ask our consultants if needed. Thread ring gauge M13 x 0.75 mm — DIN 13, tolerance 6g (Metav IndustryLine) Thread ring gauge M13 x 0.75 mm designed as a precision reference for metric ISO fine threads in production and inspection environments, right-hand thread DIN 13 compliant, tolerance class 6g Hardened gauge steel for durable use For metric ISO fine thread M13 x 0.75, right-hand Precise reference for production control Ensure reproducible conformity checks with a traceable reference The thread ring gauge M13 x 0.75 mm is specified to meet DIN 13 with a 6g tolerance class, providing a dependable, standardised benchmark for thread acceptance. As a purpose-made ring gauge, it supplies a direct, mechanical comparison that removes ambiguity from visual inspection; when a component passes the gauge, its basic thread geometry conforms to the defined limits. This approach shortens decision loops on the shop floor, reduces rework and supports consistent quality reporting in batch production. Built for longevity and repeatable measurement on the shop floor Constructed from hardened gauge steel, this ring gauge resists wear that would otherwise alter the functional fit over time. The compact mass of 0.08 kg and the right-hand thread form a stable, easy-to-handle tool that is suited to repeated use in assembly or incoming inspection. The robust material choice minimises profile deformation and ensures the gauge preserves its reference geometry, which translates into fewer tool replacements and predictable measurement intervals. Fits smoothly into inspection workflows and documentation As a physical reference, the ring gauge integrates into existing go/no-go and acceptance procedures without the need for specialised instruments. It is ideal for routine sampling, first-article inspection and in-process checks where a quick mechanical pass/fail decision is required. Using a dedicated ring gauge streamlines documentation of conformity and facilitates traceable inspection records when paired with internal calibration routines and control plans. Metav IndustryLine supplies precision tools from Emmerich with centralised stock and support for European workshops, supporting reliable supply and consistent tool quality. For a reliable addition to the inspection bench, contact Metav Werkzeuge to discuss the Metav IndustryLine thread ring gauge M13 x 0.75 mm and receive tailored advice from our Emmerich specialists Technical data Article number: M315.213.3 GTIN: 4054469125701 Weight: 0.08 kg Material: hardened gauge steel Nominal: M13 x 0.75 Standard: DIN 13, 6g Tariff number: 90173000 Core figures Nominal size: M13 Thread pitch: 0.75 mm Tolerance class: 6g Mass: 0.08 kg Special features Right-hand metric ISO fine thread Hardened gauge steel construction Category: Gauges / Ring gauge Intended use: production and inspection reference FAQ What is this ring gauge used for? The ring gauge is used as a mechanical reference to verify thread conformity for M13 x 0.75 mm metric ISO fine threads; it provides a clear pass/fail check during inspection. Does the ring gauge comply with recognised standards? Yes, the gauge is manufactured to DIN 13 with a 6g tolerance class, ensuring measurements align with common thread standards. Which materials is the gauge made from? The ring gauge is made from hardened gauge steel, chosen to preserve thread geometry and withstand repeated use. Is this a right-hand or left-hand thread gauge? This product is supplied as a right-hand thread ring gauge for metric ISO fine threads. What is the SKU for ordering and traceability? The product is listed under SKU M315.213.3 and GTIN 4054469125701 for ordering and inventory tracking. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M13x0.75 Thread Go/No-Go Plug Gauge Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Combine robust hardened construction, DIN‑compliant tolerance (6H) and precise M13×0.75 sizing for dependable Go/No‑Go thread inspection; order the limit thread plug gauge directly via Metav Werkzeuge or consult our specialists for application guidance. Limit thread plug gauge M13 x 0.75 — Right‑hand metric ISO fine‑thread limit gauge (Metav IndustryLine) The Limit thread plug gauge M13 x 0.75 is a right‑hand metric ISO fine‑thread limit gauge designed for fast Go/No‑Go checks in production and inspection. Hardened gauge steel construction Metric ISO fine thread M13×0.75 DIN 13 tolerance class 6H Fast, repeatable thread verification on the production line This inspection plug is engineered for quick acceptance testing and routine quality checks, enabling high throughput without compromising accuracy. As a classic limit gauge, it provides an immediate Go/No‑Go decision: the “Go” end verifies conformity to nominal internal thread dimensions, while the “No‑Go” end confirms that the thread does not exceed permissible limits. Constructed from hardened gauge steel, the tool resists wear in daily use and maintains repeatability over many cycles, reducing rework and preventing downstream assembly issues. Simple integration into quality workflows with clear benefits The compact, single‑piece design supports straightforward handling and minimal operator training, which speeds up inspection steps and keeps throughput steady. Dimensional conformity is ensured by compliance with DIN 13, 6H, a widely accepted tolerance class for metric internal threads; this makes the gauge suitable for shop‑floor checks as well as incoming inspection. The combination of clear pass/fail feedback and durable materials helps standardise process control and reduces measurement ambiguity during fast‑paced production. Built for practical workshop and inspection use With a nominal size of M13×0.75 and a lightweight build, the gauge is easy to store and manoeuvre on the bench or in an inspection kit. The right‑hand thread orientation matches the majority of standard components and fasteners used in fine‑thread applications. As a purpose‑made limit thread plug gauge, it complements visual and dimensional quality checks, providing a tactile, unambiguous verification method that integrates well with existing inspection routines and fixture setups. For application advice or to request the Metav IndustryLine limit thread plug gauge for use in production inspection, contact Metav Werkzeuge in Emmerich at +49 2822 7131930 or info@metav-werkzeuge.com Technical Data Article number: M315.013.3 GTIN: 4054469122373 Weight: 0.1 kg Thread: M13 x 0.75 mm Tolerance: DIN 13, 6H Material: gauge steel, hardened Hand: right‑hand Category: Limit thread plug gauge Core technical figures Nominal diameter: 13 mm Thread pitch: 0.75 mm Weight: 0.1 kg Zolltarifnummer: 90173000 Special features Hardened gauge steel Suitable for metric ISO fine threads DIN 13 tolerance class 6H Right‑hand thread Designed for Go/No‑Go inspection FAQ What is the purpose of this gauge? The limit thread plug gauge checks internal metric threads for conformity; the Go/No‑Go arrangement delivers an immediate pass or fail assessment for the M13×0.75 internal thread. Which thread standard does the gauge follow? This Metav IndustryLine plug gauge is made to DIN 13 with tolerance class 6H, which corresponds to the standard internal thread acceptance criteria for metric ISO fine threads. Can this gauge be used on fine‑thread components in production? Yes, the M13×0.75 limit plug gauge is intended for shop‑floor and inspection use where quick verification of fine metric threads is required. What material is the gauge made from and how durable is it? Manufactured from hardened gauge steel, the tool is built for wear resistance and stable performance during frequent Go/No‑Go checks. Is the gauge right‑hand or left‑hand? The gauge is produced with a right‑hand thread, matching the common orientation of metric ISO fine threads. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M13x1 Thread Gauge Ring Right-Hand Metric ISO Fine Thread DIN 13, 6g Hardened Gauge Steel - Metav IndustryLine
Reliable pass/fail inspection is provided by a hardened‑steel No‑Go ring for metric ISO fine threads; conformity to DIN 13 with a 6g tolerance guarantees consistent acceptance criteria and repeatable quality control. Secure the gauge via Metav Werkzeuge for reliable stock supply or consult their specialists for application guidance. Thread gauge ring M13 × 1 mm (No‑Go) — hardened gauge steel, DIN 13 (6g) | Metav IndustryLine Thread gauge ring M13 × 1 mm (No‑Go) for direct verification of metric ISO fine threads in production and inspection environments, right‑hand configuration Hardened gauge steel construction Conforms to DIN 13 tolerance 6g Designed for M13 × 1 fine threads Right‑hand No‑Go ring for pass/fail checks Precise thread control that reduces rework and rejects A dedicated No‑Go ring offers a clear, objective criterion for thread acceptance: a part that enters the ring is outside the permissible limits and must be rejected. Built for the workshop floor or inspection bench, this ring follows DIN 13 with a 6g tolerance so that thread size and profile are evaluated against established standards. Using a dedicated ring gauge removes subjectivity from visual checks and speeds up batch approval, delivering measurable time savings in production lines. Durable construction for continuous use Manufactured from hardened gauge steel, the ring resists wear and retains dimensional stability under frequent use. The compact mass (0.08 kg) and robust metallurgy provide a low overall cost of ownership through extended service life and reduced need for replacement. The right‑hand configuration matches standard metric ISO fine threads and the mechanical design helps prevent false passes, maintaining reliable inspection performance over many cycles. Practical fit for quality assurance workflows Intended for routine thread control, the ring gauge integrates into incoming inspection, in‑process checks and final release procedures. Its clear pass/fail behaviour simplifies operator training and lowers the probability of escape of non‑conforming parts. Specified as a control tool rather than a measuring instrument, it complements dimensional checks and supports statistical process control strategies, improving production consistency and customer confidence. Order the Metav IndustryLine M13 × 1 No‑Go ring gauge through Metav Werkzeuge for robust thread control and dependable stock supply; call +49 2822 7131930 or email info@metav-werkzeuge.com for procurement and specification advice Technical data Article number: M315.213.4 GTIN: 4054469125718 Weight: 0.08 kg Material: Gauge steel, hardened Norm: DIN 13, 6g Function: No‑Go ring gauge (Ausschuss) Thread hand: Right Facts Thread size: M13 × 1 mm Tariff number: 90173000 Category: Gauges / Thread control Special features For metric ISO fine threads Right‑hand configuration Hardened for wear resistance Suitable for production and inspection use FAQ What does a No‑Go ring gauge check? The No‑Go ring gauge M13 × 1 mm (Metav IndustryLine, SKU M315.213.4) is used to identify threads that exceed the upper limits of the permitted tolerance; any part entering the ring indicates a non‑conforming thread. Which tolerance and standard apply to this ring? This ring follows DIN 13 with a 6g tolerance class, meaning the control criterion is aligned with established metric ISO fine‑thread specifications for M13 × 1. What is the ring made from and how durable is it? The thread gauge ring M13 × 1 mm is produced from hardened gauge steel, providing high wear resistance and sustained dimensional stability for repetitive inspection tasks. Can this ring be used on left‑hand threads? The manufactured configuration is for right‑hand threads; use must match the thread direction of the parts under inspection to ensure correct pass/fail evaluation. Where is this ring typically used in the production process? The ring gauge is suited to incoming inspection, in‑process checks and final acceptance tests where quick, binary verification of metric ISO fine threads is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M13x1 Thread Go/No-Go Plug Gauge Metric ISO Fine Thread Right-Hand DIN 13 6H Hardened Gauge Steel - Metav IndustryLine
Take advantage of a precise, standards‑compliant inspection solution: the combination of DIN 13 / 6H conformity, hardened gauge steel construction and compact handling ensures reliable thread verification and consistent production quality. Order the limit plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Limit plug gauge M13 × 1 mm — right‑hand (Metav IndustryLine) A precision limit plug gauge M13 × 1 mm designed for quick go/no‑go verification of metric ISO fine threads in production and quality control environments. Hardened gauge steel construction Conforms to DIN 13, tolerance 6H Metric fine thread M13 × 1, right‑hand Designed for repeatable go/no‑go inspection Fast, reliable thread acceptance testing that keeps production moving A limit plug gauge provides an immediate, binary check whether a threaded bore meets the specified form and tolerance. The M13 × 1 mm right‑hand gauge is manufactured to DIN 13 with tolerance class 6H, delivering measurable assurance at the inspection stage. Using a dedicated go/no‑go item reduces cycle time compared with measuring instruments and eliminates interpretation variance: a go fit confirms acceptance, a no‑go fit flags deviation. This pragmatic approach lowers scrap rates and helps maintain throughput on production lines. Durable materials and geometry for thousands of inspection cycles Made from hardened gauge steel, the gauge resists wear and retains its functional dimensions under repeated use, ensuring long service life and fewer replacements. The compact, machined profile and correct thread geometry give consistent tactile feedback during inspection, so operators obtain unambiguous results even under fast‑paced conditions. The material choice and heat treatment provide the necessary surface hardness to protect the reference profile, preserving calibration intervals and reducing operational costs through longevity. Easy integration into quality systems and traceable inventory The plug gauge is provided with clear identifiers for workshop logistics and quality records: SKU M315.013.4 and GTIN 4054469122380 facilitate stock management and traceability. As a standard inspection tool, it complements fixed gauges and dimensional measuring equipment within a quality control plan, supporting documented acceptance procedures. Procurement via Metav IndustryLine grants access to a broad range of comparable gauges, ensuring consistent standards across multiple sizes and production cells. Specify the Metav IndustryLine limit plug gauge M13 × 1 mm for robust, standards‑based thread inspection and contact Metav Werkzeuge in Emmerich for ordering or technical clarification at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M315.013.4 GTIN: 4054469122380 Manufacturer: Metav IndustryLine Material: gauge steel, hardened Standard: DIN 13, 6H Facts Thread: M13 × 1 mm, right‑hand Tolerance class: 6H Weight: 0.1 kg Customs tariff number: 90173000 Special features Limit plug gauge for metric ISO fine thread Hardened gauge steel for wear resistance Category: Gauges / Limit plug gauge Designed for go/no‑go thread verification FAQ What does a limit plug gauge check? A limit plug gauge performs go/no‑go checks on internal threads; the M13 × 1 mm plug gauge verifies whether metric ISO fine threads meet the acceptance limits without dimensional measurement. Which standard and tolerance does this gauge follow? This gauge is manufactured to DIN 13 with tolerance class 6H, providing a recognised reference for thread form and fit in industrial quality control. What material is used and how durable is the gauge? The gauge is made from hardened gauge steel, which offers significant wear resistance so the reference profile remains stable over many inspection cycles. Is this gauge suitable for right‑hand threads only? Yes. The item is specified as a right‑hand metric fine thread gauge for M13 × 1 mm applications; left‑hand variants require the corresponding left‑hand version. How is the product identified for ordering and inventory? The gauge is listed under SKU M315.013.4 and GTIN 4054469122380, which can be used to order identical replacements and to document inspection tools in inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M13x1 Thread Ring Gauge Go Metric ISO Fine Thread Right 6g, Hardened Gauge Steel DIN 13 - Metav IndustryLine
Take advantage of fast, unambiguous thread verification and long service life thanks to hardened gauge steel construction and adherence to DIN 13, tolerance 6g; the M13×1 right‑hand Go ring delivers reproducible acceptance checks for ISO metric fine threads. Order directly via Metav Werkzeuge or contact our consultants for specification support. Thread ring gauge M13×1 (Go) – DIN 13, 6g | Metav IndustryLine A thread ring gauge M13×1 (Go) for quick verification of metric ISO fine threads on right‑hand fasteners, suited to production inspection and incoming goods control Hardened gauge steel construction For metric ISO fine thread M13×1 Tolerance DIN 13, 6g Right‑hand Go ring gauge Faster, more reliable thread acceptance in production The ring is designed to reduce inspection time without compromising certainty: as a Go acceptance gauge it confirms whether threads meet the specified tolerance M13×1 by passing the part through the ring. Compliance with DIN 13 and the 6g tolerance class provides a clear, standardised decision criterion that integrates into quality plans and inspection protocols. This approach supports traceable sampling and helps maintain production throughput by avoiding ambiguous measurements and rework. Durable construction for sustained repeatability Manufactured from hardened gauge steel, the gauge resists wear and preserves dimensional stability across repeated use, which directly improves repeatability of pass/fail checks on the shop floor. The robust material choice minimises frequency of replacement and maintains consistent acceptance limits, so line-side operators and quality engineers obtain the same result across shifts. The compact weight (0.13 kg) and solid geometry make handling straightforward while the hardened finish reduces the risk of false rejects due to gauge wear. Integrates into inspection workflows and quality documentation The ring gauge supports straightforward process control in machining and assembly environments where ISO metric fine thread verification is required. As a dedicated inspection tool it simplifies operator training: one simple pass/fail action replaces time‑consuming measurements when only tolerance conformance is needed. The product is suitable for incoming inspection, final checks and first‑article verification, and complements statistical process control schemes by providing a fast binary result that links to lot traceability and quality records. For standardised, robust thread verification, order the Metav IndustryLine M13×1 Go ring via Metav Werkzeuge or speak to our specialists at info@metav-werkzeuge.com or +49 2822 7131930 for technical advice. Technical Data Article number: M315.113.4 GTIN: 4054469124056 Tariff number: 90173000 Weight: 0.13 kg Facts Thread: M13×1 Tolerance class: 6g Direction: Right‑hand Standard: DIN 13 Special features Material: Gauge steel, hardened Type: Go (acceptance) ring gauge Category: Thread inspection gauge FAQ What does “Go” mean for this ring gauge? The Go designation indicates that the ring is an acceptance gauge; if a threaded part passes the M13×1 Go ring gauge it conforms to the intended tolerance class (DIN 13, 6g) for fit acceptance. Can this gauge be used for left‑hand threads? No, this ring is produced for right‑hand metric ISO fine threads; left‑hand threads require a corresponding left‑hand gauge or a separate left‑hand variant. Which standard is this gauge manufactured to? The gauge is made and specified to the DIN 13 standard with tolerance class 6g, providing a recognised reference for acceptance testing of ISO metric fine threads. How does the hardened material benefit inspection? Hardened gauge steel increases wear resistance and dimensional stability, which preserves the acceptance limit over many cycles and ensures consistent inspection results with the M13×1 Go ring. Is this suitable for production line spot checks? Yes, the ring gauge is ideal for rapid pass/fail checks in production and incoming inspection, where quick, unequivocal verification of thread acceptability is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M13x1.5 Thread Ring Gauge Go, Metric ISO Fine Thread Right-Hand, Hardened Gauge Steel DIN 13 6g - Metav IndustryLine
Compact, hardened construction and DIN 13 conformity make this gauge a durable choice for repeatable thread inspection; the M13×1.5 size suits fine metric threads in production and maintenance. Order the appropriate Go ring gauge directly via Metav Werkzeuge or consult our specialists for application guidance. Go ring gauge M13 × 1.5 mm (DIN 13) — metric ISO fine thread, right-hand — Metav IndustryLine The Go ring gauge M13 × 1.5 mm is a precision checking tool for external metric ISO fine threads, manufactured to DIN 13 and executed as a right-hand Go ring for efficient pass/fail inspection. Hardened gauge steel construction for long service life Conforms to DIN 13 with 6g tolerance class For metric ISO fine thread M13×1.5, right-hand Consistent, repeatable thread verification to support quality control A Go ring gauge made from hardened gauge steel provides a stable reference that resists wear and preserves the inspection limit over many cycles; this material choice translates into repeatable checks and reduced rework in production. The ring format performs a single, unambiguous inspection: the component passes when it enters the gauge freely, which simplifies go/no-go decisions on the shop floor. Specified to DIN 13 and the 6g tolerance class, the gauge aligns with common engineering standards for metric ISO fine threads, giving a clear, standards-based basis for acceptance criteria. Efficient inspection workflow and practical workshop handling The compact mass of 0.13 kg and the straightforward Go-only geometry allow quick inline or bench inspection without specialist fixturing, which supports faster cycle times and simpler process control. The gauge is particularly suitable where frequent checks of external threads are required, such as assembly lines, maintenance departments or incoming part inspections. Because the tool refers directly to the DIN 13 limit, recorded pass counts and simple sampling plans can be implemented with minimal training, improving throughput while maintaining compliance with inspection routines. Durable design that lowers measurement uncertainty The combination of a hardened material and precise manufacturing to the stated thread form reduces wear-induced tolerance drift and keeps measurement uncertainty low over time. The right-hand configuration and the M13×1.5 sizing are suited to fine-thread applications in mechanical assemblies and machine components where consistent engagement and alignment are essential. Clear identification for traceability — including article coding and a global trade item identifier — supports stock management and documentation for quality records, making the gauge a practical component of an audit-ready inspection toolkit. For reliable thread inspection choose the Metav IndustryLine Go ring gauge and contact Metav Werkzeuge for tailored advice and prompt dispatch from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article code: M315.113.6 GTIN: 4054469124063 Label: Gewinde‑Lehrring M13 x 1,5 mm, Go, DIN 13 Facts Nominal thread: M13 × 1.5 mm Tolerance class: 6g (DIN 13) Weight: 0.13 kg Tariff code: 90173000 Special features Material: hardened gauge steel Type: Go ring gauge (right-hand) Application: Verification of metric ISO fine external threads Category: Precision gauges / inspection rings FAQ What does the Go function verify on a threaded part? The Go ring verifies that the external metric ISO fine thread meets the minimum acceptance form and size; the Go ring gauge M13 × 1.5 mm allows the part to pass if it enters freely and confirms the external thread is within the manufactured limit. For which thread standard is this gauge intended? This gauge is manufactured to DIN 13 and targets external metric ISO fine threads in the 6g tolerance band, making it suitable for standardised fine-thread inspections. What are the construction and durability characteristics? Constructed from hardened gauge steel, the ring offers high wear resistance and stable inspection limits, supporting repeated checks with low drift over time. How does the gauge support traceability in the workshop? The inspection ring is supplied with clear identification and a global trade item number, facilitating inventory control and documentation of inspection equipment within quality systems; the article code is M315.113.6. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M13×1.5 Thread Gauge Ring Right-Hand Fine Pitch DIN 13, 6g, Hardened Gauge Steel - Metav IndustryLine
Take advantage of fast, unambiguous thread verification and durable construction for consistent quality control; procure the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Thread ring gauge M13 x 1.5 — right-hand, DIN 13 (6g) by Metav IndustryLine The Thread ring gauge M13 x 1.5 is a right-hand metric ISO fine-thread gauge designed for quick verification of external threads in production and inspection environments. *DIN 13 tolerance 6g *Hardened gauge steel construction *Metric fine thread M13 x 1.5 right-hand *Compact and lightweight 0.08 kg Fast, unambiguous verification to reduce rework The primary advantage of this gauge is its ability to deliver immediate go/no-go results for external threads, speeding up routine inspections and shop-floor checks. By applying a simple pass/fail measurement principle, the device removes ambiguity from thread assessment and supports a smoother production flow. The M13 x 1.5 profile, matched to the DIN 13 specification, ensures compatibility with standard metric fine-thread components and reduces the risk of costly rework. Durable build for repeated workshop use Manufactured from hardened gauge steel, the component is optimised for frequent handling and maintains measurement integrity over many cycles. The robust material and heat treatment resist wear at the thread flanks, so the gauge retains its form under regular use. At 0.08 kg, the item is sufficiently light for handheld checks while offering the stiffness required for reliable engagement on external threads, making it a practical tool for both bench and production-line environments. Conformance to standards gives documentary confidence Engineered to DIN 13 with tolerance class 6g, the gauge supports traceable conformity checks against metric ISO fine-thread requirements. Using documented standards simplifies quality procedures and streamlines communication with suppliers and customers. Where documented inspection results are required, the product’s specification allows clear reference to the applicable norm, reducing interpretation errors in quality records and part acceptance. Simple integration into existing inspection routines The compact format and familiar working principle allow easy integration into established quality workflows without specialist training. The device is intended for external-thread verification of right-hand threads and can be used alongside optical or tactile inspection methods to confirm fit. Clear labelling and a concise profile mean that the gauge can be stored with other inspection tools and retrieved for rapid use during routine audits or incoming goods checks. Choose Metav IndustryLine’s thread ring gauge for dependable daily checks — contact Metav Werkzeuge in Emmerich for procurement and technical guidance at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M315.213.6 GTIN: 4054469125725 Weight: 0.08 kg Material: Gauge steel, hardened Standard: DIN 13, 6g Facts Thread size: M13 x 1.5 Direction: Right-hand Tariff code: 90173000 Category: Gauges / Inspection tools Special features Design: Metric ISO fine-thread verification Suitable for external thread inspection Compact, workshop-friendly format FAQ What thread form does this gauge check? The thread ring gauge M13 x 1.5 checks external metric ISO fine threads with a 1.5 mm pitch, manufactured to the DIN 13 profile. Is the gauge suitable for left-hand threads? No, this specific item is a right-hand gauge and is intended for verification of right-hand external threads only. What does the tolerance class 6g mean for inspection? Tolerance class 6g indicates the acceptance limits for external thread geometry under DIN 13, so the gauge confirms whether an external thread falls within those limits. How durable is the gauge in daily use? Made from hardened gauge steel, the M13 x 1.5 gauge is designed for repeated engagement and retains its profile under typical workshop conditions. Can this gauge be used for internal thread checks? This ring gauge is intended for external thread verification; internal threads require a corresponding thread plug gauge or other suitable internal-measurement method. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M13×1.5 Thread Go/No-Go Plug Gauge Right-Hand Metric ISO Fine Pitch DIN 13 6H, Hardened Gauge Steel - Metav IndustryLine
Take advantage of precise thread verification with a hardened gauge steel construction and conformity to DIN 13 (6H); this reduces rework and secures assembly fit. Order the limit thread plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Limit thread plug gauge M13 x 1.5 – Metric ISO fine thread, right‑hand (Metav IndustryLine) The Limit thread plug gauge M13 x 1.5 is a hardened, right‑hand gauge for rapid verification of metric ISO fine threads in production and inspection environments Hardened gauge steel construction Conforms to DIN 13, tolerance class 6H Metric fine thread M13 x 1.5 Right‑hand thread form Ensuring reproducible thread quality on the shop floor A limit thread plug gauge provides an objective pass/fail check of internal threads, enabling fast decisions during incoming inspection or final assembly. Manufactured from hardened gauge steel, the instrument resists wear and preserves the thread profile across repeated use. Conformity with DIN 13 and tolerance class 6H means that mating parts produced to the same standard will fit reliably, reducing the risk of production stoppages. The compact mass of 0.1 kg keeps handling straightforward and supports rapid sampling routines without compromising measurement integrity. Robust material choice that supports long service life The choice of gauge steel, hardened for the body offers a clear operational benefit: consistent contact geometry under load and resistance to deformation. This durability translates into fewer gauge replacements and lower process variability over time, which in turn supports predictable assembly yields. The right‑hand thread form and the metric ISO fine pitch M13 x 1.5 are common in precision mechanical assemblies, so the gauge integrates directly into established quality processes, supplying a simple technical statement of conformity rather than subjective judgement. Practical application in inspection and production workflows Designed as a straightforward limit gauge, the component fits into lean inspection stations and portable tool sets alike. Use the item for spot checks during production runs or as a go/no‑go control in batch acceptance; the normative reference DIN 13, 6H provides a traceable acceptance criterion for quality documentation. The lightweight design and clear thread designation facilitate rapid operator training and quick identification on the workbench. By implementing standardised mechanical gauges like this, process engineers improve throughput while maintaining documented evidence of dimensional compliance For advise on application suitability or to secure supply of the Metav IndustryLine limit thread plug gauge M13 x 1.5, contact Metav Werkzeuge GmbH in Emmerich by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930 — our technical team will assist with selection and delivery options Technical data Article number: M315.013.6 GTIN: 4054469122397 Weight: 0.1 kg Facts Thread size: M13 x 1.5 Tariff number: 90173000 ECLASS: 21170235 Special features Material: gauge steel, hardened Norm: DIN 13, 6H Thread direction: right‑hand Category: Gauges; Measuring pins Manufacturer brand: Metav IndustryLine FAQ What is the primary function of this gauge? The limit thread plug gauge is used to verify internal metric ISO fine threads; the Metav IndustryLine limit thread plug gauge M13 x 1.5 confirms conformity to DIN 13, 6H. Which materials and thread forms does the gauge address? This gauge checks metric ISO fine thread profiles in right‑hand format; the hardened gauge steel construction ensures the contact geometry remains stable during routine inspections. How is conformity documented when using this gauge? Acceptance is made against the normative criterion DIN 13, tolerance class 6H; entries in inspection records refer to the gauge designation (Limit thread plug gauge M13 x 1.5, SKU M315.013.6) and the pass/fail outcome. Can this instrument be used at the production line for spot checks? Yes, the gauge is suited to rapid spot checks and routine quality control at assembly or inspection points thanks to its compact mass and standard thread size. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14 x 0.75 Thread Master Ring For Metric ISO Fine Thread Right-Hand, Hardened Gauge Steel DIN 13 6g - Metav IndustryLine
Combine consistent thread verification with hardened gauge‑steel construction and DIN 13 tolerance for dependable in‑process inspection; order the M14 thread ring gauge directly via Metav Werkzeuge or consult our specialists for application advice. Thread ring gauge M14 x 0.75 mm — DIN 13 6g, hardened gauge steel A Thread ring gauge M14 x 0.75 mm intended for fast verification of external metric ISO fine threads in production and quality control environments. Verification to DIN 13, tolerance 6g Hardened gauge steel construction Suitable for M14 x 0.75 metric fine threads Right‑hand 'go' ring for production checks Dependable verification that reduces rework and scrap The ring is designed as a dedicated 'go' gauge for external metric ISO fine threads, providing a clear, binary verification: the part either passes the ring (within the upper and lower limits set by DIN 13) or it requires attention. This straightforward check shortens inspection cycles and supports lean production workflows, because a single, robust gauge removes ambiguity during rapid sampling. The combination of standardised tolerance 6g and hardened construction ensures repeatable dimensional control without frequent adjustment. Robust materials and clear traceability for long service life Manufactured from hardened gauge steel, the gauge resists wear in daily use while preserving measurement integrity over time. The material selection and heat treatment deliver surface hardness that minimises profile erosion, so calibration intervals are extended and replacement costs fall. The compact form and modest mass of 0.14 kg make the item easy to handle in busy inspection bays, while the DIN reference offers unambiguous traceability for quality documentation and auditing processes. Practical fitment: how the gauge is used in inspection routines This ring is intended for right‑handed metric threads M14 x 0.75 mm and functions as the 'go' verification in a pair of gauges or as a standalone check. In practice, the thread must enter the gauge smoothly; any binding or failure to start indicates non‑conformity. Because the gauge follows DIN 13 tolerancing, it integrates directly with existing ISO‑aligned inspection plans and sampling procedures, enabling consistent pass/fail decisions and straightforward recording in inspection logs. Efficiency and compliance for production environments Adopting standardised gauges shortens decision time on the shopfloor and reduces dependency on subjective assessments. The simple mechanical design requires no power or electronics, which eliminates setup time and potential downtime related to battery or sensor faults. Paired with a regular calibration schedule and documented control plans, the gauge supports continuous compliance and contributes to a predictable, auditable quality chain. For reliable thread control with Metav IndustryLine, request the M14 x 0.75 mm ring gauge via Metav Werkzeuge or ask our inspection consultants in Emmerich for compatibility advice at +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M315.114.3 GTIN: 4054469124094 Weight: 0.14 kg Material: hardened gauge steel Facts Thread size: M14 x 0.75 mm Tolerance class: DIN 13, 6g Customs tariff number: 90173000 Special features Right‑hand metric ISO fine thread 'Go' ring verification for external threads For production and inspection use Compact, low mass for easy handling FAQ What does the 'go' designation mean for this ring gauge? The 'go' ring verifies that external threads meet the permitted maximum material condition; the M14 x 0.75 mm ring gauge (Metav IndustryLine, SKU M315.114.3) should accept compliant parts smoothly. Is this gauge suitable for metric ISO fine threads only? Yes, the ring is made specifically for metric ISO fine threads of size M14 x 0.75 mm and is manufactured to DIN 13 tolerancing. How durable is the material used for the gauge? Constructed from hardened gauge steel, the gauge offers high wear resistance and long service life under normal inspection use. Can this ring be used for on‑machine checks? The gauge is a mechanical verification tool intended for inspection stations; it requires manual handling and visual assessment during the check. How should the gauge be stored to preserve accuracy? Store the ring in a dry, dust‑free environment and handle it carefully to avoid nicks; keep it in protective packaging when not in use to extend intervals between calibrations. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14 x 1.25 Thread Ring Gauge Go Right-Hand Metric ISO Fine Pitch DIN 13, 6g, Hardened Gauge Steel - Metav IndustryLine
Robust, hardened construction and DIN 13 tolerance class ensure efficient, repeatable go/no-go checks of M14×1.25 metric fine threads; combined with compact handling and low weight this creates a cost-effective inspection process for small-batch and series production. Order the gauge directly via Metav Werkzeuge or consult our technical advisors for application support. Thread ring gauge M14 × 1.25 (Go) — Metric ISO fine thread, hardened gauge steel — Metav IndustryLine The Thread ring gauge M14 × 1.25 (Go) is a hardened go ring for rapid acceptance checks of M14×1.25 metric ISO fine threads (right-hand), ideal for workshop and production control. Hardened gauge steel for long service life Conforms to DIN 13 tolerance class 6g For M14×1.25 metric ISO fine threads Fast, reliable acceptance checks for threaded parts A dedicated Go ring gauge provides immediate pass/fail decisions for threaded components, reducing time spent on dimensional analysis. The gauge is made for M14×1.25 metric fine threads and conforms to DIN 13, 6g, which defines the tolerance band used in production control. By using a dedicated ring for acceptance, inspection cycles are shortened and scrap rates fall, because incorrect threads are identified at first touch rather than after assembly steps or machining downstream. Built to withstand workshop handling and frequent use Constructed from gauge steel, hardened, the ring offers durability under repeated use and resists deformation that would otherwise compromise measurement integrity. At around 0.1 kg, the item is easy to handle on the shop floor and quick to pass between operators or inspection stations. The compact form allows snug engagement with the thread flank, ensuring the intended interference is checked without elaborate fixtures; fewer handling steps translate into lower process overhead and less downtime for maintenance. Integrates into quality routines and inventory systems The ring is suited to routine production inspection, incoming goods checks and final assembly controls where metric ISO fine threads are present. Use of a Go gauge streamlines standard operating procedures and supports consistent results across shifts. The gauge can be logged into stock systems via its SKU and GTIN for traceability and ordering, helping maintain a controlled inventory of precision tools and ensuring timely replacement when wear limits are reached. Metav’s distribution and quality filter in Emmerich support reliable supply for industrial customers. Request a technical quote or application advice from Metav Werkzeuge for this Metav IndustryLine M14 Go ring gauge; contact our consultants at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific production tasks Technical data Article number: M315.114.5 GTIN: 4054469124117 Weight: 0.1 kg Facts Thread size: M14 × 1.25 Tolerance class: DIN 13, 6g Thread direction: Right-hand Special features Type: Go ring gauge (acceptance) Material: Gauge steel, hardened Application: Metric ISO fine thread inspection FAQ What is the primary function of this ring gauge? The ring gauge is a Go (acceptance) gauge for quick go/no-go checks of metric fine threads; it verifies that an M14×1.25 thread lies within the specified DIN 13, 6g tolerance. Can this gauge be used on both left- and right-hand threads? This particular ring gauge is intended for right-hand metric ISO fine threads and will not fit left-hand thread forms. How does the DIN 13, 6g specification affect inspection? DIN 13, 6g establishes the tolerance band for the thread; the ring gauge is manufactured to that class so it represents the acceptable maximum material condition for a go check. Is the material suitable for frequent workshop use? Yes, the gauge is made from hardened gauge steel, designed to resist wear from repeated engagement with threaded parts in routine inspection tasks. How should the gauge be managed for traceability and replacement? Log the SKU and GTIN into the inventory system and follow a wear-replacement routine; the GTIN facilitates reordering and stock control. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14x0.5 Thread Go Ring For Metric ISO Fine Thread Right-Hand, Hardened Gauge Steel DIN 13 6g - Metav IndustryLine
Take advantage of precise pass/fail checking and robust construction to speed up thread inspection while reducing scrap. The hardened gauge steel body and conformity to DIN 13 (6g) ensure reproducible results for metric fine threads. Order the thread ring gauge directly via Metav Werkzeuge or consult our specialists for application advice. Thread Ring Gauge M14 x 0.5 (Go) — DIN 13, hardened gauge steel — Metav IndustryLine The Thread Ring Gauge M14 x 0.5 (Go) is a compact pass gauge for rapid verification of right‑hand metric ISO fine threads in production and quality control. DIN 13 tolerance class 6g Hardened gauge steel construction For M14 x 0.5 mm ISO fine threads Right‑hand Go pass gauge for quick checks Ensure fast, reliable go/no‑go inspection on the shopfloor A dedicated pass gauge delivers decisive go/no‑go results without complex setup. The M14 x 0.5 Go ring provides an immediate check that a thread falls within the DIN 13 tolerance band, reducing downtime spent on micrometric measurement where only conformity needs confirmation. Manufactured from hardened gauge steel, the ring maintains its form and thread profile over repeated use, enabling consistent inspection throughput and fewer uncertain decisions during production runs. Robust design for repeated use and minimal maintenance Built to resist wear in an industrial environment, this pass gauge prioritises longevity and low upkeep. The hardened gauge steel composition offers high surface hardness and dimensional stability, so recalibration intervals are extended and handling routines remain simple. The compact body and straightforward engagement make the gauge suitable for bench checks and in‑process control, supporting lean inspection workflows while keeping replacement and maintenance costs low. Practical fit into quality systems and traceable inspection Using a dedicated pass gauge streamlines quality routines: a positive fit on the Go side confirms acceptable thread form, enabling rapid acceptance without elaborate instrumentation. The ring corresponds to the 6g tolerance class for metric ISO fine threads, a common standard in mechanical assemblies, which simplifies documentation and supplier control. Its light weight (0.14 kg) and clear designation support traceability in inspection logs and parts lists, aiding audits and standardised procedures. Contact Metav Werkzeuge GmbH for application guidance and to secure this Metav IndustryLine M14 x 0.5 Go thread ring gauge for dependable thread verification on your production line Technical data Article number: M315.114.2 SKU: M315.114.2 GTIN: 4054469124087 Facts Thread size: M14 x 0.5 Tolerance class: DIN 13, 6g Weight: 0.14 kg Tariff number: 90173000 Special features Material: hardened gauge steel Type: Go (pass) ring gauge Thread form: metric ISO fine thread, right‑hand Category: Gauges / Measuring instruments FAQ What does the Go designation mean for this ring gauge? The Go designation indicates that the ring gauge is a pass gauge; the Thread Ring Gauge M14 x 0.5 (Go) must engage the test thread without force for the part to be accepted within the specified tolerance. Can this gauge be used for inspection on the shopfloor? Yes, the Metav IndustryLine ring gauge is designed for routine shopfloor checks; its hardened gauge steel construction resists wear from repeated use and supports quick in‑process verification. Which tolerance class is covered by this gauge? This ring corresponds to DIN 13 with tolerance class 6g, suitable for standard metric ISO fine thread acceptance and common in mechanical assembly quality criteria. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14x0.5 Thread GO/NO‑GO Plug Gauge Metric ISO Fine Thread Right-Hand Hardened Gauge, DIN 13 6H - Metav IndustryLine
Ensure consistent assembly quality by combining hardened gauge steel construction with the DIN 13 tolerance class 6H for reliable pass/fail inspections; the compact M14 × 0.5 right‑hand plug gauge speeds routine checks and reduces rework. Order the gauge directly via Metav Werkzeuge or consult their specialists for selection support. Limit thread plug gauge M14 × 0.5 (right‑hand) — Thread plug gauge, hardened gauge steel — Metav IndustryLine The Limit thread plug gauge M14 × 0.5 (right‑hand) is a go/no‑go inspection tool designed for rapid verification of metric ISO fine threads in production and workshop environments. Hardened gauge steel construction Conforms to DIN 13 tolerance class 6H Right‑hand M14 × 0.5 nominal thread Compact workshop weight 0.1 kg Faster, dependable pass/fail inspection for fine threads A dedicated thread plug gauge such as this offers a rapid, unequivocal method for pass/fail inspection of threaded parts. The M14 × 0.5 nominal dimension and fine‑pitch profile enable direct verification of mating parts and taps without time‑consuming measurement setups. By reducing uncertainty at the inspection stage, this gauge helps limit assembly errors and lowers downstream rework rates — a clear efficiency gain for repetitive production runs and incoming goods checks. Durable construction that follows recognised standards Manufactured from hardened gauge steel, the gauge resists wear under frequent use and maintains dimensional stability across inspection cycles. Compliance with DIN 13 and tolerance class 6H provides a recognised baseline for thread fit and interchangeability; the specification ensures the tool corresponds to common engineering practice for metric ISO fine threads. The right‑hand orientation matches standard thread directions used in most components, and the compact mass supports fast handling at the inspection bench. Simple integration into quality routines and traceable checks Designed for straightforward use as a go/no‑go plug gauge, the tool fits easily into existing inspection protocols and gauges stacks. Its clear acceptance criteria speed decision making on the shop floor, while the robust material choice minimises the need for early replacement. Metav IndustryLine supplies this gauge as part of a broad quality‑assurance range, supporting traceable workflows and dependable availability for small workshops through to industrial users. The compact format also aids ergonomic handling during repetitive checks. For assured thread acceptance and continuity of supply, request the Metav IndustryLine thread plug gauge via Metav Werkzeuge or contact their product specialists in Emmerich for tailored advice and fast fulfilment Technical data SKU: M315.014.2 GTIN: 4054469122410 Weight: 0.1 kg Thread size: M14 × 0.5 Hand: Right‑hand Material: Gauge steel, hardened Standard: DIN 13, 6H Data Nominal diameter: 14 mm Pitch: 0.5 mm Weight (approx.): 0.1 kg Customs tariff number: 90173000 Special features Go/no‑go plug gauge function Hardened gauge steel for wear resistance Tolerance class 6H for metric ISO fine threads Compact format for bench inspection Category: Gauges / Thread plug gauges FAQ What does the M14 × 0.5 designation mean for the gauge? The M14 × 0.5 marking denotes a metric nominal diameter of 14 mm with a fine thread pitch of 0.5 mm; the limit thread plug gauge checks that this specific thread form meets fit requirements. Is the gauge suitable for workshop use and frequent checking? Yes, the hardened gauge steel construction is designed for routine go/no‑go inspections in workshop and production environments, offering durable service under regular handling. Which standard does the gauge follow and why is that important? The tool conforms to DIN 13 with tolerance class 6H, providing a recognised reference for thread fit and ensuring compatibility with standard metric ISO fine threads. Can this gauge replace full dimensional measurement during incoming inspection? A limit plug gauge provides quick acceptance testing; it is ideal for fast pass/fail decisions. For full dimensional characterisation, complementary measurement tools are recommended. What is the intended application for a right‑hand plug gauge? Right‑hand plug gauges verify threads that turn clockwise to tighten, which is the predominant thread direction in general engineering and assembly. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14x0.75 Thread Go Gauge For Metric ISO Fine Thread, Right-Hand, Hardened Gauge Steel, DIN 13 6g - Metav IndustryLine
Take advantage of a compact, standards‑compliant inspection tool that combines hardened gauge steel, exact metric sizing and easy handling for routine thread verification; order directly via Metav Werkzeuge or contact the consultants for technical advice. Thread ring gauge M14 × 0.75 — hardened gauge steel, DIN 13 (6g) A thread ring gauge M14 × 0.75 for fast verification of metric ISO fine right‑hand threads in production and incoming inspection. Hardened gauge steel construction DIN 13 tolerance 6g compliance For metric ISO fine thread M14 × 0.75 Lightweight at 0.08 kg Accurate conformity for process control The ring is manufactured to DIN 13 with tolerance 6g, making it suitable for routine pass/fail checks on metric ISO fine threads. Thanks to the hardened gauge steel body, the instrument maintains dimensional stability under frequent use, which supports consistent production decisions and reduces rework. The clearly defined thread size M14 × 0.75 and right‑hand orientation streamline inspection protocols and simplify go/no‑go assessments on shop‑floors and test benches. Built for repeatable inspections and workshop use Compact mass and robust construction ensure easy handling and repeatable results during serial checks. At 0.08 kg the gauge is convenient to position and rotate, while the hardened material resists wear that would otherwise erode tolerances over time. This durability translates into fewer replacements and less measurement drift, so verification intervals remain predictable and traceable within quality routines. The form factor also makes integration into manual inspection workstations straightforward. Designed to support quality systems and documentation The gauge aligns with established metrology practice for thread control and is appropriate for manufacturers and inspection labs that rely on standardised tools to demonstrate part conformity. Using a dedicated ring gauge for M14 × 0.75 simplifies traceable acceptance procedures and supports clear documentation of inspection outcomes; this fosters objective decision‑making in incoming goods checks and final inspections, reinforcing overall process reliability. Select the Metav IndustryLine thread ring gauge for reliable M14 × 0.75 verification and contact Metav Werkzeuge for procurement or technical consultation. Technical data Article number: M315.214.3 GTIN: 4054469125756 Mass / thread: M14 × 0.75 Weight: 0.08 kg Facts Standard: DIN 13 Tolerance: 6g Tariff code: 90173000 Eclass: 21170214 Special features Material: hardened gauge steel Thread direction: right‑hand Category: gauges, measuring instruments Label: Gewinde‑Lehrring for metric ISO fine thread FAQ What is the intended use of this ring gauge? This ring gauge is intended for verification of M14 × 0.75 metric ISO fine right‑hand threads in production and inspection environments. Which standard does the gauge comply with? The gauge is manufactured to DIN 13 with tolerance 6g, suitable for routine go/no‑go inspections. What material is the gauge made from and why does that matter? The gauge is made from hardened gauge steel, offering wear resistance and dimensional stability for repeatable inspections. Can this gauge be used for left‑hand threads? This specific item is for right‑hand threads; left‑hand checks require a correspondingly specified ring gauge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14x0.75 Thread Go/No-Go Plug Gauge Right-Hand Metric ISO 6H Hardened Gauge Steel - Metav IndustryLine
Reliable inspection of M14×0.75 metric fine threads through a compact, hardened gauge-steel design delivering repeatable acceptance checks; the plug meets DIN 13, 6H and handles right‑hand threads with minimal wear. Order the thread limit plug directly via Metav Werkzeuge or ask our consultants if needed. M315.014.3 Thread limit plug — M14 x 0.75 (DIN 13, 6H) · Metav IndustryLine The M315.014.3 is a hardened gauge-steel thread limit plug for verification of M14×0.75 metric ISO fine threads, right‑hand, designed for workshop and inspection use Hardened gauge-steel construction Conforms to DIN 13, 6H Compact 0.1 kg for easy handling Right-hand metric fine thread M14×0.75 Consistent acceptance checks for fine threads A purpose-built thread limit plug offers an immediate, objective decision at the inspection point: acceptable or out of tolerance. With designation M14×0.75 and compliance to DIN 13, 6H, this plug gauge provides a defined limit standard that supports reproducible acceptance in incoming inspection and final quality control. The measured geometry directly corresponds to the ISO fine-thread profile, reducing interpretation effort and accelerating go/no-go decisions on small‑pitch threaded components. Durable construction for repeatable measurements Constructed from hardened gauge steel, the gauge is dimensionally stable under normal workshop conditions and resists premature wear that would otherwise undermine inspection repeatability. Its compact mass of 0.1 kg and slim form factor make handling straightforward at the test bench or on the shop floor; the low weight aids rapid tactile assessment without compromising stiffness. These material and form choices reduce downtime caused by frequent replacements and simplify routine verification tasks. Practical use in production and quality workflows The plug is intended for right‑hand metric fine threads and suits batch sampling, assembly checks and spot inspections where a quick acceptance verdict is required. When used as part of a documented inspection routine, the gauge complements torque and fit control by verifying the internal thread form against an established limit. Its clear nominal designation and standard conformity support traceable documentation and easier integration into existing quality plans and production control routines. Choose Metav IndustryLine thread limit plugs for reliable, repeatable thread inspection — contact Metav Werkzeuge in Emmerich for availability and expert advice. Technical data Article number: M315.014.3 GTIN: 4054469122427 Customs tariff: 90173000 Facts Thread: M14 x 0.75 Weight: 0.1 kg Standard: DIN 13, 6H ECLASS: 21170235 Special features Material: hardened gauge steel Right-hand metric fine thread Category: gauges / plug gauges Suitable for workshop and inspection use FAQ What thread size does this gauge check? This plug gauge verifies M14×0.75 metric ISO fine threads; the M315.014.3 is specified for this nominal and pitch. Does the gauge meet a recognised standard? Yes, the M315.014.3 is manufactured to conform with DIN 13, 6H, providing a standardised acceptance criterion for inspection. What material is the gauge made from and why does it matter? The gauge is made from hardened gauge steel to ensure dimensional stability and resistance to wear, which sustains repeatable acceptance checks. Is this plug suitable for production sampling and final inspection? The design and conformity to DIN 13 make it appropriate for both routine production sampling and final quality inspections of metric fine threads. How is the right‑hand designation relevant? The plug is manufactured for right‑hand thread forms; this ensures correct profile engagement and prevents misleading results when checking standard right‑hand metric threads. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14x1 Thread Go Ring Gauge For Metric ISO Fine Thread Right Hand, DIN 13 6g - Metav IndustryLine
Take advantage of precise thread verification through DIN 13 conformity and hardened gauge steel for durable, repeatable inspections; order directly via Metav Werkzeuge or consult the specialists for integration into existing quality workflows. Thread ring gauge M14 x 1 mm — ISO metric fine thread inspection ring, right-hand The Thread ring gauge M14 x 1 mm is a hardened inspection ring designed to check compliance with ISO metric fine threads (DIN 13, tolerance 6g) on right-hand components DIN 13, tolerance 6g Hardened gauge steel construction For M14 x 1 mm ISO fine thread, right-hand Compact 0.08 kg inspection ring Ensure conformity with clear reference limits A calibrated thread ring gauge provides an objective go/no-go reference that removes ambiguity from visual checks. Built to DIN 13 with a 6g tolerance, the inspection ring defines the acceptable boundary for external threads: parts that pass the ring meet the specified dimensional and form criteria, while parts that fail are immediately identifiable. This method shortens inspection time and reduces downstream rejects by introducing a physical verification step that is straightforward to apply in incoming inspection or final assembly. Robust material and simple handling for routine use Manufactured from hardened gauge steel, the inspection ring resists wear and maintains dimensional stability through repeated use, ensuring long service life and consistent results. The compact, lightweight construction (approx. 0.08 kg) makes the tool easy to position on the production line or at the measurement bench, while the right-hand geometry matches common assembly parts. As a dedicated ring for ISO metric fine thread sizes, it complements optical and tactile measuring methods by offering a quick, deterministic check that integrates well into SPC routines. Practical benefits for quality assurance and production flow Incorporating a dedicated inspection ring into quality processes delivers measurable efficiency: faster acceptance of conforming parts, clear rejection criteria for non-conforming items and reduced rework cycles. The ring serves as a first-line control during machining, after heat treatment or prior to shipment, enabling teams to make rapid decisions without complex instrumentation. For regulated environments, a consistent mechanical gauge like this supports documentation of inspection steps and standardised handling across shifts and sites. Contact Metav Werkzeuge for expert advice on thread verification and to source this inspection ring directly from Emmerich; order assistance and compatibility checks are available via info@metav-werkzeuge.com or by phone at +49 2822 7131930 Technical Data Article number: M315.214.4 GTIN: 4054469125763 Thread size: M14 x 1 Weight: 0.08 kg Standard: DIN 13, 6g Facts Tolerance class: 6g Country tariff number: 90173000 Category: Gauges / Inspection rings Special features Material: gauge steel, hardened Thread direction: right-hand Application: ISO metric fine thread inspection Compact design for routine checks FAQ What does the DIN 13, 6g marking mean for inspection? The DIN 13, 6g marking identifies the thread form and tolerance band used by the Thread ring gauge M14 x 1 mm; it indicates that the ring corresponds to the 6g acceptance class for ISO metric threads, providing a defined limit for go/no-go checks. Can this ring gauge be used on plated or coated threads? Plated or coated threads may alter the effective diameter; the inspection ring M14 x 1 mm should be used with consideration of coating thickness to avoid false rejects—measurements or supplier specifications for the plating should be referred to when in doubt. How should the ring gauge be stored to preserve accuracy? The inspection ring should be kept clean, dry and protected from mechanical damage; storing in a protective case and avoiding contact with hard particulates will help the hardened gauge steel retain its dimensional integrity. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14x1 Thread Ring Gauge, Right-Hand ISO Metric Fine Pitch, DIN 13 6g, Hardened Gauge Steel - Metav IndustryLine
Combine cost-effective design, hardened gauge steel and DIN‑compliant 6g tolerance for dependable pass/fail checking of metric fine threads; order the Go thread ring gauge M14 x 1 directly via Metav Werkzeuge or ask our consultants if needed Go thread ring gauge M14 x 1 — hardened gauge steel, DIN 13 (Metav IndustryLine) The Go thread ring gauge M14 x 1 is a right‑hand metric ISO fine‑thread ring gauge intended for rapid go/no‑go verification in production and quality control environments Hardened gauge steel construction DIN 13 tolerance class 6g Right‑hand metric ISO fine thread Lightweight 0.07 kg for easy handling Ensure fast, standards‑based pass/fail inspection The go ring gauge provides an unequivocal pass/fail check that speeds up routine inspections on the shop floor. Conforming to DIN 13 with a tolerance class of 6g, the gauge delivers consistent acceptance criteria for M14 x 1 fine threads. Using a ring gauge eliminates interpretation of measurement charts: if the thread fits the gauge, the thread is within tolerance. This approach reduces inspection time, lowers the risk of rejected assemblies and supports a predictable production flow by making quality decisions immediate and reproducible. Designed for everyday workshop use and comfortable handling Manufactured from hardened gauge steel, the ring gauge combines wear resistance with a compact form factor. At approximately 0.07 kg, it is easy to handle during repetitive checks and can be operated single‑handed on assembly lines or in maintenance jobs. The compact mass reduces operator fatigue and helps keep cycle times low. For workshop environments where throughput matters, the simple go/no‑go criterion provided by the gauge supports quick decisions without complex metrology equipment. Material integrity and measurement repeatability The gauge body is produced from hardened gauge steel, ensuring dimensional stability and long service life under normal workshop conditions. The choice of material and heat treatment reduces wear-induced drift, so periodic verification suffices to retain traceable results. As a direct comparison tool rather than a measuring instrument, the ring gauge offers high repeatability for go‑checks and is compatible with routine quality protocols that require reliable, rapid assessments of threaded components. Practical integration into inspection workflows Using a go thread ring gauge simplifies documentation and training: acceptance is binary and records can reference the applied standard (DIN 13) and tolerance class (6g). The gauge is suitable for incoming inspection, in‑process checks and final assembly control of metric ISO fine threads. Its robust construction makes it suitable for frequent use in industrial contexts, aiding process standardisation and supporting consistent output quality across shifts. Choose Metav IndustryLine's hardened ring gauge for reliable thread verification and benefit from Metav Werkzeuge's supply and advisory services in Emmerich Technical data SKU: M315.114.4 GTIN: 4054469124100 Eclass: 21170214 Facts Thread size: M14 x 1 Pitch: 1 mm Tolerance class: 6g Weight: 0.07 kg Special features Material: gauge steel, hardened Standard: DIN 13 Thread direction: right‑hand Function: Go (pass) ring gauge FAQ What does "go" mean for this ring gauge? The term "go" indicates a pass gauge: if the thread accepts the Go thread ring gauge M14 x 1, the thread meets the specified tolerance and is considered acceptable. Which standard does the gauge comply with? The gauge is manufactured to DIN 13 with a tolerance class of 6g, providing a standardised acceptance limit for M14 x 1 metric ISO fine threads. How often should the gauge be checked for wear? Inspection intervals depend on usage frequency; the ring gauge should be verified regularly against a calibrated reference to ensure continued accuracy and repeatability. Is this gauge suitable for production line checks? Yes. The hardened construction and simple go/no‑go function make the gauge well suited for high‑throughput production and routine quality control tasks. Can this gauge be used on left‑hand threads? No. This item is a right‑hand thread ring gauge; left‑hand threads require a corresponding left‑hand gauge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14x1.25 Thread Gauge Ring Right-Hand ISO Fine Thread DIN 13, Hardened Gauge Steel - Metav IndustryLine
Ensure consistent thread conformity with the combination of hardened gauge steel, the DIN 13 (6g) tolerance and precise M14 x 1.25 dimensions; benefit from a compact, shop‑ready inspection tool. Order the gauge directly via Metav Werkzeuge or consult the technical team for application-specific advice. Thread ring gauge M14 x 1.25 — Metric ISO fine thread, DIN 13 (6g) The thread ring gauge M14 x 1.25 is a precision inspection ring designed to verify external metric ISO fine threads in production and quality control environments DIN 13 tolerance class 6g Hardened gauge steel construction For metric ISO fine thread M14 x 1.25 Suitable for right‑hand threads Reliable verification for fine threads on the shop floor A compact inspection ring that delivers fast, repeatable checks of external threads: the body is made from hardened gauge steel, providing stable geometry and wear resistance for long inspection intervals. The conformity to DIN 13 with tolerance class 6g places this gauge in the common industrial band for external metric threads, allowing reliable acceptance testing during assembly or final inspection. As a plain functional control, the ring confirms whether an M14×1.25 thread meets the nominal profile and pitch, supporting traceable quality decisions without over‑complex procedures. Practical use and benefits for production and inspection Engineered for routine checks, the ring is particularly suited to workshop inspection benches and inline control points where simple, objective evidence of conformity is required. The nominal sizing M14 x 1.25 corresponds to a 14 mm major diameter and a 1.25 mm pitch, which are typical for metric fine‑thread components. The inspection ring’s compact form and low weight facilitate quick handling and reduce operator fatigue during repetitive checks, while the robust gauge steel construction helps maintain dimensional stability under everyday workshop conditions. Care, traceability and integration in quality workflows Weighing approximately 0.08 kg, the gauge is easy to store and transport between workstation and inspection area. Regular cleaning and dry storage are recommended to preserve the hardened surface and measurement integrity; light lubrication where permitted will reduce corrosion risk. The ring integrates naturally into standard quality routines as a tactile, immediate verification tool that complements measuring instruments and provides a clear pass/ fail outcome for threaded parts. Its compact design supports both small series shops and larger assembly lines seeking reproducible thread control. For robust, shop‑ready thread verification, contact Metav Werkzeuge to request detailed technical guidance or to add the Metav IndustryLine thread ring gauge M14 x 1.25 to your inspection equipment. Technical Data Article number: M315.214.5 GTIN: 4054469125770 Material: gauge steel, hardened Thread size: M14 x 1.25 Facts Nominal diameter: 14 mm Pitch: 1.25 mm Weight: 0.08 kg Tolerance class: DIN 13, 6g Special features For metric ISO fine thread, right‑hand Category: Gauges / Inspection rings Manufacturer range: Metav IndustryLine FAQ What does the tolerance class 6g indicate for this gauge? The 6g rating refers to the external thread tolerance band defined in DIN 13; it represents a commonly used industrial tolerance for metric threads and is the basis for acceptance checks performed with the thread ring gauge M14 x 1.25. Can the gauge be used for left‑hand threads? This inspection ring is manufactured for right‑hand threads and is suitable for standard right‑hand metric ISO fine threads size M14 × 1.25. How should the ring gauge be maintained to ensure longevity? Regular cleaning, dry storage and protection from corrosive environments preserve the hardened gauge steel; light corrosion protection is advised when parts are stored long‑term. Is the gauge appropriate for production‑line checks? Yes, the ring is intended for straightforward production and incoming inspection tasks where rapid, repeatable verification of M14 × 1.25 external threads is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14x1.25 Thread Go/No-Go Plug Gauge Metric ISO Fine Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Product data inconsistent: the quality status contains contradictory entries (both "good" and "scrap" indicated). This inconsistency may lead to errors or confusion in downstream processes, such as inventory management, production planning, or customer communication. Please check the source data thoroughly to identify the root cause of the conflict and resolve it promptly. Ensuring accurate and consistent quality status is essential for maintaining reliable product descriptions and overall data integrity. Once the issue has been addressed, a product description can be generated without risk of misrepresentation or further complications. Accurate data is critical for operational efficiency and decision-making processes.
M14x1.5 Thread Limit Go Gauge Metric ISO Fine Pitch Right-Hand, Hardened Gauge Steel, DIN 13 6H - Metav IndustryLine
Benefit from reliable thread verification and repeatable acceptance checks thanks to hardened gauge steel and compliance with DIN 13, 6H; the compact right‑hand design ensures fast inspection of metric fine threads. Order the limit thread plug gauge directly via Metav Werkzeuge or consult our specialists for application advice. Limit Thread Plug Gauge M14 × 1.5 — Metric ISO fine thread, right‑hand The Limit Thread Plug Gauge M14 × 1.5 is a right‑hand metric ISO fine‑thread gauge designed for quick pass/no‑go verification in production and incoming inspection. Hardened gauge steel construction Metric ISO fine thread M14 × 1.5 Tolerance class DIN 13, 6H Compact right‑hand plug gauge, 0.1 kg Ensure correct threads with standardised verification A limit thread plug gauge is the fastest way to confirm whether a threaded component meets specification. Thanks to the M14 × 1.5 geometry and DIN 13, 6H tolerance class, the gauge allows objective acceptance checks without interpretation. The tool serves as a binary control: the “go” condition verifies minimum material and thread fit, while the “no‑go” condition guards against oversize or out‑form threads. Such measured verification shortens inspection time and reduces scrap by preventing incorrect assemblies from progressing through production. The compact form factor supports rapid sampling on the shop floor and in receiving inspection. Robust construction for consistent, repeatable checks Manufactured from hardened gauge steel, this plug gauge resists wear and maintains dimensional integrity over repeated use. The right‑hand configuration reflects standard thread direction for most metric fasteners and simplifies handling during serial checks. At approximately 0.1 kg, the gauge is easy to position yet substantial enough to avoid accidental damage when used correctly. The material choice and heat treatment provide long service life and predictable wear patterns, making measurement intervals and maintenance planning straightforward for quality engineers. Integrates into quality processes and traceability The plug gauge is a practical instrument for production control, assembly verification and incoming goods inspection where conformity to metric ISO fine threads is required. Its compact size suits batch sampling and inline process checks, supporting cycle‑time improvements. Identification details such as SKU and GTIN facilitate traceability and stock management within a calibrated tool pool. For regulated environments, the use of standardised gauges contributes to documented measurement procedures and reproducible results, assisting certification and audit processes. Choose the Metav IndustryLine limit thread plug gauge for dependable thread control and contact Metav Werkzeuge for procurement or technical clarification at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M315.014.6 GTIN: 4054469122458 SKU: M315.014.6 Facts Thread size: M14 × 1.5 Weight: 0.1 kg Tariff number: 90173000 Standard: DIN 13, 6H Special features Material: gauge steel, hardened Right‑hand metric ISO fine thread Category: plug gauge / limit gauge FAQ What does the M14 × 1.5 designation mean for the gauge? The designation denotes a metric ISO fine thread with a nominal diameter of 14 mm and a pitch of 1.5 mm; the Limit Thread Plug Gauge M14 × 1.5 checks conformity to that thread form. Is this a go or no‑go gauge or both in one tool? The item is supplied as a limit thread plug gauge offering the standard go/no‑go verification concept for pass/fail inspection of threads. Which tolerance class does the gauge check to? The gauge is made for the DIN 13, 6H tolerance class, suitable for standard metric ISO internal thread acceptance checks. What material and treatment ensure gauge durability? The plug gauge is manufactured from hardened gauge steel, chosen for wear resistance and dimensional stability during repeated inspections. Can the gauge be used for left‑hand threads? This specific gauge is right‑hand; left‑hand thread verification requires the corresponding left‑hand version. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14x1.5 Thread Ring Gauge ISO Metric Fine Pitch Right-Hand, DIN 13 6g Hardened Gauge Steel - Metav IndustryLine
Take advantage of the clear pass/fail control provided by a M14 x 1.5 thread ring gauge with DIN 13 tolerance class 6g and hardened gauge steel construction for durable shop‑floor inspection; order directly via Metav Werkzeuge or consult our specialists for application advice. Thread ring gauge M14 x 1.5 — No‑go ring gauge, DIN 13, hardened gauge steel (Metav IndustryLine) A Thread ring gauge M14 x 1.5 configured as a no‑go inspection tool for right‑hand metric ISO fine threads, designed for rapid acceptance testing in production and incoming inspection M14 x 1.5 metric ISO fine thread DIN 13 tolerance class 6g Hardened gauge steel construction Right‑hand thread inspection tool Fast, reliable pass/fail inspection to keep production moving The ring is manufactured to DIN 13 and tolerance 6g, enabling unambiguous go/no‑go evaluation during routine checks. As a no‑go gauge, it serves a single, decisive purpose in a quality workflow: to identify threads that exceed permissible limits and prevent out‑of‑tolerance parts advancing through the process. This direct check reduces rework, shortens inspection time and supports a predictable production throughput. Durable design for continuous shop‑floor use Crafted from hardened gauge steel, the gauge resists wear under frequent contact and maintains dimensional stability. The compact mass of 0.08 kg and robust finish ensure handling is straightforward while inspection points remain repeatable. Durable construction reduces replacement frequency and creates a reliable reference for routine thread verification, which in turn lowers total cost of ownership across production runs. Integrates cleanly into quality documentation and traceability The ring gauge is supplied with clear identification (SKU: M315.214.6, GTIN: 4054469125787) for inventory and traceability purposes, simplifying record keeping for inspection protocols. Using standardised gauges eases communication with suppliers and auditors and supports consistent results across shifts. The product from Metav IndustryLine is intended for systematic in‑line checks and incoming part control where rapid, objective decisions are required. Choose Metav IndustryLine thread gauges for robust, standards‑based inspection and contact Metav Werkzeuge in Emmerich for application guidance and supply logistics Technical data Article number: M315.214.6 GTIN: 4054469125787 SKU: M315.214.6 Facts Thread size: M14 x 1.5 Weight: 0.08 kg Standard: DIN 13, 6g Special features Material: hardened gauge steel Thread direction: right‑hand Application: metric ISO fine thread inspection Classification: no‑go (reject) ring gauge FAQ What is the intended use of this ring gauge? The ring gauge is designed as a no‑go inspection tool for M14 x 1.5 metric ISO fine threads to detect threads that exceed the permitted tolerance (DIN 13, 6g). Is the ring gauge suitable for production and incoming inspection? Yes, the hardened construction and DIN 13 tolerance make the gauge suitable for rapid pass/fail checks on the shop floor and for incoming part control. Which material is the gauge made from and how does that benefit use? The gauge is made from hardened gauge steel; this provides wear resistance and dimensional stability for repeated inspections. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14x1.5 Thread Ring Gauge Metric ISO Fine Right-Hand DIN 13, 6g Hardened Gauge Steel - Metav IndustryLine
The hardened go thread ring gauge M14 x 1.5 ensures repeatable verification of metric ISO fine threads and supports efficient quality control thanks to its DIN 13 tolerance class and robust gauge-steel construction. Benefit from consistent inspection results and long service life; order via Metav Werkzeuge or consult our technical team for fitment advice. Go thread ring gauge M14 x 1.5 — DIN 13 (6g), hardened gauge steel (Metav IndustryLine) A go thread ring gauge M14 x 1.5 designed for fast, reliable verification of metric ISO fine threads in production and inspection environments Go thread ring gauge M14×1.5, DIN 13 6g Hardened gauge steel for wear resistance Rapid verification in production inspections Ensure conformity with a single check The primary function of this ring gauge is a straightforward pass/fail verification of internal threads. Built to DIN 13 (6g), the gauge gives a clear, objective measurement standard that reduces ambiguity in daily quality checks. Using a dedicated go ring gauge simplifies inspection flow—components that pass the gauge meet the target tolerance and can proceed to assembly without additional measuring steps—contributing directly to faster throughput and fewer production hold‑ups. The combination of standard conformity and a compact verification method supports lean inspection routines and helps maintain consistent product quality. Durable design for repeated use and traceable results Manufactured from hardened gauge steel, the ring resists wear during repeated engagement, which preserves dimensional integrity over many cycles and lowers the need for frequent replacements. The chosen material and heat treatment minimise profile degradation and therefore sustain the original gauge limit, keeping maintenance overheads low. For traceability in regulated environments the item is supplied with clear identification (SKU M315.114.6, GTIN 4054469124124), aiding documentation in quality-control systems and simplifying inventory management. Practical fit for workshop and shop‑floor inspection Engineered as a right‑hand go gauge for metric ISO fine threads, the tool integrates directly into standard inspection benches and incoming‑goods routines. The lightweight construction (approx. 0.12 kg) enables fast handling during repetitive checks without compromising stiffness or user comfort. Where speed and reliability are priorities, this gauge replaces multi‑step measurement procedures with a single mechanical verification, cutting cycle time while maintaining a defensible inspection record for audits and process control. Request supply of the Metav IndustryLine go ring gauge from Metav Werkzeuge; technical advisors in Emmerich can confirm suitability for specific thread classes and production workflows — info@metav-werkzeuge.com | +49 2822 7131930 Technical data SKU: M315.114.6 GTIN: 4054469124124 Thread: M14 x 1.5 Standard: DIN 13, 6g Weight: 0.12 kg Material: Gauge steel, hardened Key figures Tariff number: 90173000 eClass: 21170214 Mass / thread form: M14 x 1.5 Features and applications Type: Go ring gauge for internal thread verification Thread form: Metric ISO fine, right‑hand Application: Production inspection and quality control Intended use: Fast pass/fail checks in workshop and shop floor environments FAQ What does the DIN 13, 6g marking mean for thread acceptance? DIN 13 specifies metric thread tolerances; the 6g tolerance band defines the acceptance limits for external threads that should pass the go thread ring gauge M14 x 1.5. Is this gauge suitable for production or laboratory use? The M14 go ring gauge is designed for production and shop‑floor inspection, providing a rapid, repeatable check suitable for incoming goods and final assembly control. How long can the gauge be expected to remain accurate under daily use? Durable hardened gauge steel construction extends service life under routine use; longevity depends on handling, cleaning and storage practices. Can this gauge be used for left‑hand threads? This specific item is a right‑hand go ring gauge for metric ISO fine threads; left‑hand versions require a dedicated left‑hand gauge. Which identifiers assist traceability in documentation and audits? Use the SKU M315.114.6 and GTIN 4054469124124 to record inspections and maintain traceable quality records for the gauge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14x2 Thread Gauge Ring Right-Hand Metric ISO Thread DIN 13, 6g Hardened Gauge Steel - Metav IndustryLine
Take advantage of the combination of DIN 13 conformity, hardened gauge steel and compact handling for reliable, repeatable thread verification in production and inspection. Order the gauge directly via Metav Werkzeuge or contact the consultants for application advice. M14 x 2 mm Thread Ring Gauge – DIN 13, 6g (Metav IndustryLine) The M14 x 2 mm Thread Ring Gauge is a hardened inspection gauge for verifying external ISO metric threads (right-hand) to DIN 13 and tolerance class 6g. Hardened gauge steel for wear resistance DIN 13 tolerance class 6g certified Designed for M14 x 2 mm ISO threads Right-hand metric thread verification Ensure correct fit and fewer rejects with standardised inspection This ring gauge provides a straightforward, standards-based method for confirming that external threads meet the geometric limits required for reliable assembly. Manufactured from hardened gauge steel, the tool resists wear so that the M14 x 2 mm thread profile remains consistent over many inspection cycles. Compliance with DIN 13 and the 6g tolerance class means inspection results are directly comparable with drawings and supplier certificates; this reduces uncertainty at goods-in and helps to cut rework and assembly failures. The compact form and low mass support quick, repeatable checks on the shop floor without complex set-ups. Robust construction for repeatable, precise checks Built for repetitive use, the ring gauge combines a hard-bodied material with precision ground thread flanks, delivering stable go/no-go assessment of external threads. The hardened construction maintains the thread profile under routine handling and prevents the gradual rounding that undermines accuracy. As a result, inspection teams gain measurable time savings: fewer false rejects, faster throughput, and a reliable acceptance criterion that integrates cleanly into quality control procedures. The clear specification against ISO metric thread standards makes it simple to include this gauge in inspection plans and calibration schedules. Practical workshop integration and traceable results The gauge's concise design is optimised for everyday use in production, incoming inspection and maintenance environments. Markings and the SKU allow straightforward inventory control and traceability within quality records. For businesses aiming to harmonise tool fleets across locations, this item offers a direct performance-to-cost proposition: a standardised method for thread verification that supports consistent assembly quality and reduces downstream troubleshooting. Metav’s experience in supplying precision tools ensures compatibility with common inspection procedures and offers peace of mind through dependable product quality. For assured thread inspection and application guidance, request the M14 x 2 mm gauge from Metav Werkzeuge—technical consultants in Emmerich are available to advise on integration and supply. Technical Data Article number: M315.214 GTIN: 4054469125732 eClass: 21170214 Customs tariff number: 90173000 Numbers / Facts Thread size: M14 × 2 mm Pitch: 2 mm Tolerance class: 6g Standard: DIN 13 Special features Material: hardened gauge steel Thread form: ISO metric, right-hand Category: gauges (Lehren) SKU: M315.214 FAQ What thread form does this gauge check? The M14 x 2 mm Thread Ring Gauge checks external ISO metric threads, right-hand form, in accordance with DIN 13 and the 6g tolerance class. Is the gauge suitable for incoming inspection on production parts? Yes, the gauge is designed for routine incoming and in-process inspection to confirm that external M14 × 2 mm threads meet the specified tolerance limits. How does hardened gauge steel benefit workshop use? Hardened gauge steel increases wear resistance so the gauge retains accurate thread flanks over extended use, ensuring consistent results when using the M14 x 2 mm ring gauge. Can this gauge be included in calibration schedules? The gauge can be integrated into a company’s calibration routine and inventory control; use the SKU M315.214 for traceability in quality records. What standard should be referenced when recording inspection results? Inspection results should be recorded against DIN 13 and the stated 6g tolerance class to ensure clear, standardised acceptance criteria. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
M14x2 Thread Ring Gauge, Right-Hand, Tolerance 6g DIN 13, Hardened Gauge Steel - Metav IndustryLine
Take advantage of a compact, standards‑compliant inspection tool that combines DIN 13 / 6g tolerance control with wear‑resistant hardened gauge steel, ensuring fast go/no‑go checks and long service life; order the thread ring gauge directly via Metav Werkzeuge or ask our consultants for application advice. Thread ring gauge M14 x 2 mm 'go' — DIN 13, hardened gauge steel (Metav IndustryLine) The Thread ring gauge M14 x 2 mm 'go' is a precision ring gauge for verifying external metric ISO threads to DIN 13, designed for right‑hand M14 × 2 mm threads in production and inspection environments. DIN 13, tolerance 6g for metric ISO threads Hardened gauge steel for long service life Suitable for M14 × 2 mm right‑hand threads Faster decisions with a single go/no‑go check A dedicated 'go' ring gauge provides an immediate pass result for external threads, making it ideal for rapid quality control at incoming inspection stations or on the shop floor. The nominal size M14 x 2 mm and the 6g tolerance correspond to the ISO metric standard, so acceptance testing is consistent with common engineering drawings. Because the gauge is manufactured from hardened gauge steel, wear is minimised and repeatability is maintained over many cycles — a practical advantage when several hundred threaded parts are checked each shift. Reduce rework and protect downstream assembly Using a calibrated ring for quick verification reduces the risk of assembling out‑of‑tolerance components and the costs that follow. The ring’s compliance with DIN 13 gives a clear numerical basis for decisions in reject or accept workflows, supporting traceable quality processes and lowering scrap rates. The compact format and light mass enable fast handling and easy integration into routine inspection jigs; the result is measurable time savings and more predictable assembly outcomes. Robust handling and straightforward integration into quality routines The ring’s construction in hardened gauge steel resists deformation and provides consistent seating on the thread flank, which is essential for reproducible checks. The tool is a straightforward addition to a gauge set or inspection bench and complements dial or digital comparators for more detailed assessments. For procurement and process planning, Metav’s role as a European quality filter ensures reliable supply and technical advice from Emmerich, supporting workshop-level precision without unnecessary complexity. Contact Metav Werkzeuge for tailored advice on integrating this Metav IndustryLine ring gauge into inspection routines and to secure prompt delivery from our Emmerich stock Technical data Article number: M315.114 GTIN: 4054469124070 Nominal size: M14 × 2 Material: hardened gauge steel Standard: DIN 13, tolerance 6g Weight: 0.14 kg Facts Thread pitch: 2 mm Nominal diameter: 14 mm Tolerance grade: 6g Tariff number: 90173000 Type: 'go' ring gauge Special features Designed for metric ISO threads (right‑hand) Conforms to DIN 13 Wear‑resistant hardened gauge steel Category: Gauges / Ring gauges Manufacturer brand: Metav IndustryLine FAQ What does the 'go' function mean for this ring gauge? A 'go' ring gauge verifies that an external thread meets the minimum material and form requirements; the Thread ring gauge M14 x 2 mm 'go' confirms acceptance of M14 × 2 mm threads within the DIN 13, 6g tolerance. Can this ring gauge be used for left‑hand threads? No, this gauge is specified for right‑hand metric threads; left‑hand checks require a corresponding left‑hand gauge. How does the material affect the gauge life? Manufactured from hardened gauge steel, the ring resists flank wear and maintains dimensional stability, extending service life compared with softer materials. Is the gauge suitable for production line checks? Yes, the compact M14 × 2 mm ring is well suited for routine in‑process or incoming inspections where fast go/no‑go decisions reduce cycle time. What documentation is supplied with the gauge? The gauge is supplied with product identification and conformity to the stated standard; for specific calibration certificates or traceability requirements, please consult Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Fast, tactile checks where electronics are impractical
Gauges and test pins provide unequivocal go/no-go results for threads, bores, gaps and radii without relying on electronics. The range covers plug gauges and ring gauges for internal and external threads, feeler gauges and precision feeler strips for micro‑gap assessment, plus probe pins and measuring pins for tactile diameter and pitch checks.
How these tools work in the production environment
Mechanical gauges operate as direct reference standards: a plug gauge or ring gauge verifies conformity to thread profiles and mating ability, while limit gauges separate accept from reject in a single step. Test pins are used to tactilely measure small bore diameters, centre‑to‑centre distances and radii. Manufactured from hardened gauge steel or ceramic and often precision lapped, these instruments deliver immediate physical results that are ideal for incoming inspection, machine‑side checks and final control.
Measurable benefits that affect production performance
- Reduced scrap and rework through rapid, unambiguous pass/fail assessment.
- Increased repeatability thanks to very low measurement uncertainty and fine lapping.
- Lower downtime: quick checks at the machine save cycle time and reduce setup periods.
- Durable construction with high wear resistance from specialised, low‑distortion alloys.
- Versatile delivery formats: individual gauges, organised sets in wooden cases or metre‑length feeler rolls compliant with DIN 2269.
Why Metav is the practical choice for precision supplies
Metav combines decades of expertise with a broad warehouse and quality filtering from Emmerich. As a precision partner for industry, craft and trade, Metav supplies a comprehensive selection of gauges and test pins alongside complementary tools such as precision calipers and setting rings. With over 48,000 customers and a catalogue exceeding 250,000 items, Metav is positioned to supply reliably, reduce vendor complexity and support traceable quality control to national standards.
Summary
Gauges and test pins are indispensable for dependable, repeatable quality assurance where tactile, mechanical verification is preferred. Choose these plug gauges, ring gauges, feeler strips and probe pins when immediate, robust measurement decisions are required on the shop floor.
FAQ
What materials are gauges and test pins typically made from?
Gauges and test pins are usually manufactured from hardened gauge steel for durability and wear resistance; ceramic variants are available where thermal stability and minimal wear are critical.
How do thread gauges ensure mating capability?
Thread plug gauges and ring gauges check flank diameters and thread form against standards, providing a clear go/no‑go verdict that confirms pairability with mating parts.
Which tolerance class should I choose for probe pins and gauge sets?
Select tolerance classes aligned with your inspection requirements; for high‑precision tasks, sets produced to DIN 2269 or equivalent tolerance classes ensure micrometre‑level control and repeatability.
Can feeler gauges measure contact gaps in valve and engine work reliably?
Yes. Feeler gauges and precision feeler strips, supplied either as a fan or metre‑length rolls, allow accurate assessment of valve clearances and contact gaps down to micrometre increments.
How do limit gauges speed up in‑process inspection?
Limit gauges separate good from bad in a single, tactile operation, enabling rapid go/no‑go checks at the machine and reducing both inspection time and the likelihood of human interpretation errors.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com