TPGA 110204 TH10 Wendeplatten - Tungaloy
The sharp combination of an uncoated carbide TH10 grade and a 0.4 mm corner radius delivers low cutting forces and clean surface finishes, while the ISO-standard triangular geometry ensures straightforward integration into existing tool systems; order the part directly via Metav Werkzeuge or consult our specialists for compatibility guidance. TPGA110204 TH10 triangular insert for Turning — Tungaloy TPGA110204 TH10 indexable insert for ISO-standard external and internal turning, optimised for low cutting forces and high-quality surface finishes on non‑ferrous materials ISO-standard triangular geometry Uncoated carbide TH10 for low cutting forces 0.4 mm corner radius for fine surface finish Cylindrical hole for secure, repeatable clamping High efficiency and surface quality with a sharp uncoated grade The TPGA110204 TH10 insert is an ISO-standard triangular turning insert engineered as an economical, sharp uncoated carbide solution for operations where reduced cutting forces and clean surfaces matter. The TH10 grade is a universal, sharp grade tailored for non‑ferrous materials and applications that benefit from a keen cutting edge rather than a coated geometry. A 0.4 mm corner radius reduces burr formation and supports a finer surface finish without excessively increasing cutting forces, which aids throughput on lighter machining setups. For users seeking tangible productivity gains, the insert’s geometry supports stable cutting at appropriate feeds, yielding consistent component appearance and fewer secondary operations. Fit and system integration explained for predictable results Compatibility with toolholders is determined by a combination of form, relief angle, tolerance class, fastening method, size and thickness. The insert features an 11° relief angle and a 60° triangular profile, with a cylindrical hole to secure placement and repeatability in the pocket. When selecting a clamping system, consider the matching pocket form and the correct shim or clamping set; the typical system comprises the ISO insert, a compatible outer holder or boring bar, a backing shim or clamp set, and replacement screws. Using properly specified components preserves the insert’s seating accuracy, reduces vibration and secures the intended geometry transfer from cutter to component, which in turn supports predictable component tolerances and surface quality. Application guidance and selection criteria for best results This insert is supplied without a chipbreaker, making it suitable where chip form is already controlled by workpiece material or process settings, or where uninterrupted chip flow is acceptable. For turning aluminium alloys, copper and other non‑ferrous substrates the TH10 grade often outperforms coated alternatives in terms of cutting force and surface appearance. However, for abrasive or hardened steels a different coated or tougher grade should be chosen. When specifying the insert, match the insert size (11), thickness (2.38 mm) and seating form to the holder to ensure clamp stability. If in any doubt about selecting the optimal grade or holder combination, technical consultation can avoid costly trial and error and improve first‑pass yield. Contact Metav Werkzeuge today to confirm holder compatibility for the Tungaloy TPGA110204 TH10 insert and to arrange an order or technical consultation — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6808768 Manufacturer SKU: TUN6808768 Model series: ISO turning inserts Material: carbide Grade: TH10 Coating: uncoated Shape: triangular Size: 11 Thickness: 2.38 mm Corner radius: 0.4 mm Relief angle: 11° Included angle: 60° Hole: with cylindrical hole Application: Turning Numbers Thickness: 2.38 mm Size: 11 Corner radius: 0.4 mm Relief angle: 11° Included angle: 60° Article number: 6808768 SKU: 6808768-Tungaloy Special features ISO‑standardised triangular insert Uncoated carbide, universal sharp grade TH10 suited to non‑ferrous materials No chipbreaker Cylindrical hole for secure positioning Compatibility determined by form, relief angle, tolerance class, fastening, size and thickness System components: holder, backing shim/clamp set, replacement screws FAQ What materials is this insert best suited for? The TPGA110204 TH10 insert is designed primarily for non‑ferrous materials such as aluminium and copper alloys; the TH10 uncoated grade delivers low cutting forces and clean surface finishes in these applications. Does the insert require a specific holder type? Compatibility depends on matching form, relief angle, tolerance class, fastening method, size and thickness; the TPGA110204 should be used in holders specified for ISO triangular inserts with matching seat geometry. What does the lack of a chipbreaker mean in practice? A insert supplied without a chipbreaker produces simpler chip geometry control requirements; the TPGA110204 TH10 is best where chip evacuation is managed by process parameters or where continuous chips are acceptable. How does the 0.4 mm corner radius affect machining? The 0.4 mm corner radius balances edge strength and surface finish: it helps reduce burrs and improve appearance while keeping cutting forces moderate for a sharper uncoated edge. Is this insert suitable for internal turning as well as external turning? Yes — the ISO design and the TPGA geometry support both external and internal turning when used in an appropriately configured boring bar or holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 110302 BX360 Wendeplatten - Tungaloy
Take advantage of the combination of high wear resistance, ISO compatibility and precise finishing geometry for reliable, repeatable turning operations; the CBN grade ensures long tool life on hardened components while the triangular 60° form gives stable engagement and easy indexing. Order the insert directly via Metav Werkzeuge or consult the sales engineers for guidance on holder compatibility and optimal machining parameters. TPGA 110302 BX360 — TPGA indexable insert for Turning by Tungaloy TPGA 110302 BX360 TPGA indexable insert for precision turning and finishing of hardened components, designed for ISO-system holders and stable clamping. CBN grade BX360 for hardened steels Triangular ISO insert, 60° cutting angle Cylindrical hole, secure clamping 0.2 mm corner radius for fine finishing High-performance cutting for wear-intensive finishing The TPGA110302 BX360 insert combines a cubic boron nitride (CBN) cutting material with an engineered grade for sustained performance on hardened steels. The CBN substrate provides superior abrasive wear resistance compared with conventional carbide, enabling consistent dimensional results during last-pass turning and plunge finishes. This translates into longer intervals between indexings, reduced tooling consumption and a measurable improvement in surface integrity when finishing high-hardness components. ISO conformity and mechanical fit cut setup time Built to ISO indexable insert standards, the triangular geometry and cylindrical hole guarantee secure fixation with compatible holders. The specified relief angle of 11° and 60° insert form ensure predictable engagement and force distribution, reducing vibration and runout. As a result, changeovers and re‑indexing are quicker and set-up reproducibility improves, supporting higher machine utilisation. If uncertain about holder compatibility or the best clamping arrangement, the technical team can provide clarification by email at info@metav-werkzeuge.com or by phone at +49 2822 7131930. Application focus and economic advantages Designed primarily for turning applications, the insert is optimised for finishing on high-hardness workpieces and, depending on component requirements, can also address certain cast iron operations. The fine 0.2 mm corner radius supports tight tolerances and reduces edge chipping during light cuts, while the absence of a dedicated chipbreaker simplifies edge preparation for consistent finishes. Overall, the material and geometry selection delivers a favourable balance between process stability and tool-life economy, particularly in small-batch and high-precision machining contexts. Contact Metav Werkzeuge for specialist advice on integrating the Tungaloy TPGA 110302 BX360 insert into production and to secure the right holder and feed/speed recommendations Technical Data Article number: 6808774 Manufacturer SKU: TUN6808774 Dealer SKU: 6808774-Tungaloy Model series: ISO-Drehwendeschneidplatten Brand: Tungaloy Facts Insert form/angle: 60° Relief angle: 11° Corner radius: 0.2 mm Plate thickness: 3.18 mm Inscribed circle / size: 11 mm ISO designation: 110302 Special features Material: carbide Cutting material: cubic boron nitride (CBN) Grade: BX360 Application: Turning Plate shape: triangular Hole: with hole (cylindrical) Chipbreaker: none Typical system: ISO indexable insert compatible FAQ What materials is this insert suitable for? The TPGA 110302 BX360 insert (Tungaloy indexable insert, SKU 6808774-Tungaloy) is primarily intended for hardened steels and, in certain grades, can be used for cast iron finishing depending on component and process demands. How does the BX360 grade differ from carbide inserts? BX360 is a CBN-based grade; unlike carbide, the BX360 cutting material excels in abrasive wear resistance on hardened materials, giving longer tool life in finish turning applications. Is a chipbreaker required for good surface finish? This insert is supplied without a chipbreaker, relying on the CBN edge and fine 0.2 mm corner radius for controlled cutting and fine finishes; chip evacuation depends on holder geometry and cutting parameters. Can this insert be used with standard ISO holders? Yes — the insert conforms to ISO indexable insert dimensions and the triangular form with a cylindrical hole ensures compatibility with corresponding ISO-system holders when matched for form, thickness and tolerance class. What cutting geometry helps to achieve consistent results? The combination of the 60° insert form, 11° relief angle and 0.2 mm corner radius provides stable engagement, reduced vibration and repeatable dimensional control in finishing passes. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 110302 DX140 Wendeplatten - Tungaloy
Combining the PCD cutting edge of DX140 with a precise 60° triangular geometry and a 0.2 mm nose radius delivers sustained high-speed performance for aluminium and other non-ferrous materials; the result is fewer tool changes and a more predictable production rhythm. Order the Tungaloy insert directly via Metav Werkzeuge or consult our specialists for application-specific selection. TPGA110302 DX140 ISO triangular turning insert — PCD grade by Tungaloy The TPGA110302 DX140 is an ISO triangular turning insert with a polycrystalline diamond cutting surface, optimised for high-speed turning of aluminium and non‑ferrous materials. PCD grade DX140 for extended tool life Triangular ISO form, 60° included angle 0.2 mm nose radius for fine detail Cylindrical-holed insert, 3.18 mm thick Maximised productivity through PCD technology The DX140 grade uses a polycrystalline diamond (PCD) cutting surface that is inherently hard-wearing and chemically stable against non-ferrous alloys. When machining aluminium and similar materials, the PCD edge enables significantly higher cutting speeds and a much longer tool life, which reduces downtime for insert changes and increases part throughput. The material behaviour of PCD minimises built-up edge on soft metals, which translates into more consistent surface finish and fewer scrap parts. This results-oriented design supports efficient production planning and clear cost-per-part improvements. Geometry and clamping for repeatable accuracy The insert’s triangular ISO form with a 60° included angle and a 0.2 mm nose radius provides a balance between cutting stability and detail capability. The 11° clearance angle ensures adequate relief to avoid rubbing while maintaining a strong cutting edge. Compatibility with standard ISO holders is governed by the insert’s form, clearance angle, tolerance class, fastening method, size and thickness, so reliable clamping and repeatable positioning are achieved when the correct holder and pad are selected. Predictable tool behaviour from the geometry reduces setup variability and supports tight process control. Robust substrate and application range for economical machining Brazed or bonded onto a cemented carbide substrate, the PCD layer on this insert is designed to combine the hardness of diamond with a shock‑resistant core. Grade DX140 is intended for aluminium, non-ferrous metals and abrasive non-metallic materials where long tool life and high cutting rates are required. The insert is supplied without a chipbreaker, so the selection of a chipformer and the appropriate grade should match workpiece material, machining type and machine stability. Reduced tool consumption and fewer tool changes mean lower process costs over production runs. System considerations and practical use recommendations An ISO insert functions as part of a system: the insert, a suitable external holder or boring bar, a support pad/clamping set and the correct fastening screws must be matched for secure operation. The TPGA110302 DX140 is supplied with a cylindrical hole for positive clamping and is 3.18 mm thick, which contributes to the overall stiffness of the cutting arrangement. For best results, select a holder that provides rigid support and favourable rake/clearance conditions; when machining thin-walled or unstable components, reduce feed or engage a different grade designed for lower vibration. If application conditions are uncertain, consultation on holder choice and process parameters is recommended to ensure consistent, economical machining. Contact Metav Werkzeuge for tailored advice on Tungaloy PCD inserts and to secure TPGA110302 DX140 for high-speed turning; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and delivery options Technical Data Article number: 6808773 Manufacturer SKU: TUN6808773 Product SKU: 6808773-Tungaloy Model series: ISO turning inserts Designation: TPGA110302 DX140 Manufacturer: Tungaloy Application: Turning Core specifications Size: 11 mm Thickness: 3.18 mm Nose radius: 0.2 mm Clearance angle: 11° Included angle: 60° Hole: with cylindrical hole Special features Polycrystalline diamond (PCD) cutting material Grade DX140 for aluminium and non‑ferrous metals Cemented carbide substrate No chipbreaker supplied Triangular plate form Compatible with ISO holders and bars System composition: insert, outer holder/boring bar, pad/clamping set, spare screws FAQ What materials is this insert best suited for? The TPGA110302 DX140 uses a PCD cutting surface and is optimised for aluminium, other non‑ferrous metals and abrasive non‑metallic materials where high cutting speeds and long tool life are required. Can the insert be used for internal and external turning? Yes; the insert is designed for both external and internal turning when paired with the appropriate external holder or boring bar, clamping pad and fastening hardware. How does the lack of a chipbreaker affect performance? The TPGA110302 DX140 is supplied without a chipbreaker, so chip control depends on the selected chipformer and machining parameters; this allows flexibility to match chip management to the workpiece and operation. What does the cylindrical hole mean for clamping? The cylindrical hole ensures secure, repeatable clamping when used with compatible holders and clamping sets; correct matching of the hole style to the clamping hardware is essential for process stability. Is the DX140 grade suitable for high-speed production runs? Yes, the DX140 grade is formulated for high cutting speeds and extended tool life in appropriate materials, offering economic advantages over frequent insert replacement. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 110302 NS9530 Wendeplatten - Tungaloy
Data inconsistency: the product is described as "Hartmetall" (carbide) in one field but as an uncoated cermet in another — please verify and correct the material specification to ensure accuracy and consistency across all fields, as this discrepancy could lead to confusion or errors in product classification, selection, or usage, particularly for customers or stakeholders relying on precise material details for technical applications, procurement decisions, or quality assurance processes; addressing this issue promptly will help maintain trust, prevent potential misunderstandings, and uphold the integrity of the product's documentation, which is crucial for effective communication and operational efficiency in relevant contexts.
TPGA 110302 TH10 Wendeplatten - Tungaloy
Take advantage of a proven combination of ISO conformity, an uncoated carbide TH10 grade and compact geometry to achieve low cutting forces and clean surfaces in non‑ferrous turning operations; order directly via Metav Werkzeuge or ask the consultants for application guidance. TPGA110302 TH10 Tungaloy insert — ISO triangular turning insert, 60° geometry, cylindrical hole The TPGA110302 TH10 is a triangular ISO turning insert for external and internal turning applications, designed for efficient machining of non‑ferrous materials where a sharp, uncoated cutting edge reduces cutting forces and improves surface finish. ISO triangular insert, 60° geometry Uncoated carbide TH10 for low cutting forces 11° clearance, 0.2 mm corner radius Cylindrical hole for secure clamping Consistent, efficient cutting for non‑ferrous materials The insert is made from carbide in the TH10 grade and is uncoated, which supports a particularly sharp edge. This results in lower cutting forces and a cleaner surface on materials such as copper alloys and aluminium. The combination of a defined 60° geometry and a 0.2 mm corner radius helps to distribute cutting loads while maintaining dimensional control; this is particularly useful in finishing passes where surface quality matters. For production environments seeking predictable tool behaviour, the sharp, uncoated edge of this insert offers a practical balance between economy and performance. Reliable seating and holder compatibility for uninterrupted production Designed to ISO standards, the insert’s triangular form and cylindrical hole ensure compatibility with a wide range of ISO turning holders and boring bars when the correct form, clearance and tolerance class are observed. The 11° clearance minimises rubbing and improves chip evacuation, which in turn reduces vibration and wear on the holder assembly. Proper seating and the use of the correct clamping set or screw maintain positional accuracy and repeatability, supporting longer runs with fewer interruptions. Clear selection criteria and predictable process results Selection of this insert should be based on workpiece material, machining stability and desired surface finish. The uncoated carbide makes the grade well suited to light to medium cutting conditions and to applications where low cutting force is a priority. In less stable setups, pairing the insert with an appropriate chipbreaker or a more robust holder reduces the risk of chatter; where a fine surface is required, smaller corner radii and the sharp TH10 edge enable improved finish without excessive cutting loads. The ISO conformity simplifies integration in existing tool inventories and supports fast, error‑free selection. Practical benefits for workshop workflows Using an ISO‑standard insert reduces setup time and allows quick replacement during scheduled tool changes, improving overall machine uptime. The triangular form provides three usable cutting edges per insert, optimising tooling cost per edge when compared with single‑edge alternatives. Moreover, the simple geometry and uncoated edge allow predictable regrinding or inspection approaches in toolrooms that prefer manual edge maintenance. These operational advantages contribute to reliable cycle times and consistent part quality across batch runs. Contact Metav Werkzeuge for tailored advice on using the Tungaloy TPGA110302 TH10 insert in specific machining scenarios and request application support or order details from Metav Werkzeuge. Technical data Article number: 6808772 Manufacturer SKU: TUN6808772 Material: carbide Model series: ISO turning inserts ISO designation: TPGA110302 Shape: triangular Size: 11 mm Thickness: 3.18 mm Corner radius: 0.2 mm Clearance angle: 11° Insert angle: 60° Hole style: cylindrical hole Grade / sort: TH10 Application: turning Facts Thickness: 3.18 mm Insert size: 11 mm Corner radius: 0.2 mm Clearance angle: 11° Main angle: 60° Article number: 6808772 Manufacturer SKU: TUN6808772 Special features Uncoated carbide grade TH10 Triangular insert with three cutting edges Cylindrical hole for positive clamping ISO‑compliant geometry for holder compatibility Intended for turning, external and internal FAQ What materials is this insert best suited for? The TPGA110302 TH10 insert is optimised for non‑ferrous materials such as aluminium and copper alloys, where the sharp, uncoated TH10 edge promotes low cutting forces and good surface finish. How does the insert secure to the holder? The triangular insert features a cylindrical hole and ISO geometry that enable secure clamping in compatible holders when the correct clamp and screw are used. Can this insert be used for finishing passes? Yes — the combination of a 0.2 mm corner radius and the sharp carbide edge of the TH10 grade is suitable for finishing operations that require reduced cutting force and improved surface quality. Is the insert compatible with standard ISO holders? The ISO designation TPGA110302 ensures compatibility with ISO‑standard turning holders, subject to correct matching of form, clearance angle and tolerance class. How many cutting edges are available per insert? The triangular shape provides three usable cutting edges, offering cost efficiency through multiple indexed positions. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 110304 BX360 Wendeplatten - Tungaloy
Take advantage of the BX360 CBN grade, precise 0.4 mm corner radius and ISO TPGA form for reliable hard-turning performance; order the TPGA110304 insert directly via Metav Werkzeuge or ask our consultants if needed. TPGA110304 BX360 — Tungaloy triangular turning insert, CBN grade for hardened-steel finishing The TPGA110304 BX360 is an ISO triangular turning insert designed for precision external and internal turning of hardened steels and, depending on the application, cast iron. CBN grade BX360 for hardened steels ISO TPGA triangular insert form 0.4 mm corner radius for fine finishes 11° clearance angle for secure cutting Supplied without chipbreaker High-performance CBN for wear-intensive finishing The core advantage of the insert is its CBN cutting material, BX360, which delivers exceptional wear resistance on high-hardness components. Where conventional tools wear quickly, this grade keeps the cutting edge stable, enabling longer uninterrupted cycles and more consistent part geometry. The combination of CBN and a carbide substrate provides thermal stability and abrasion resistance, which translates into a measurable improvement in process reliability for hard-turning applications. Geometry tailored for precision and surface quality The insert’s geometry—TPGA triangular form with an included angle of 60°, an inscribed circle of 11 mm, a 0.4 mm corner radius and 3.18 mm thickness—is engineered for reproducible clamping and repeatable machining results. The 11° clearance prevents rubbing and reduces cutting forces, helping to achieve a superior surface finish and minimised tool deflection. These defined dimensions support predictable tool life and make component set-up faster in production environments. Process benefits and recommended use cases Optimised for finishing and hard-turning, this grade excels in applications where dimensional accuracy and surface integrity are paramount. The absence of an integrated chipbreaker means the insert is intended for stable set-ups and controlled cutting conditions; choose a compatible holder and cutting parameters to match material, operation and machine rigidity. The result is efficient material removal with reduced rework and a consistent finish on hardened steels. System compatibility and handling guidance Compatibility with toolholders depends on form, clearance angle, tolerance class, fixing method, size and thickness; the insert is supplied with a cylindrical hole for positive clamping. Typical system components include the ISO triangular insert itself, the appropriate external holder or boring bar, a shim/clip and replacement clamping screw. For secure integration, verify holder geometry and torque settings and select the correct grade and chip control strategy for the component material and operation. For high-hardness finishing tasks choose the Tungaloy TPGA110304 BX360 insert and contact Metav Werkzeuge for procurement or technical advice at info@metav-werkzeuge.com or +49 2822 7131930 — our technical consultants will assist with holder compatibility and process optimisation. Technical Data Article number: 6808777 Manufacturer SKU: TUN6808777 SKU: 6808777-Tungaloy Manufacturer: Tungaloy Grade: BX360 Material: carbide Data Inscribed circle: 11 mm Thickness: 3.18 mm Corner radius: 0.4 mm Clearance angle: 11° Included angle: 60° Hole: with cylindrical hole Special features CBN cutting material suited for hardened steels ISO triangular insert TPGA form Supplied without chipbreaker Compatibility determined by form, clearance, tolerance, fixing, size and thickness System components: insert, outer holder or boring bar, shim/clip and replacement screw FAQ Which materials is this insert suitable for? The TPGA110304 BX360 insert is designed primarily for hardened steels and can be used for certain cast-iron applications depending on the workpiece and cutting conditions. What advantages does BX360 CBN offer over conventional carbide inserts? BX360 CBN provides superior wear resistance and thermal stability on hard materials, resulting in longer tool life and more consistent surface quality compared with conventional carbide grades. How does the insert clamp into standard holders? Clamping depends on form, clearance, tolerance class, fixing method, size and thickness; the TPGA110304 has a cylindrical hole for positive fixing and requires a matching ISO TPGA holder or boring bar. Is there a chipbreaker fitted on this insert? This insert is supplied without a chipbreaker; chip control should be managed via holder geometry, cutting parameters or a chosen chip-control insert style where required. What key dimensions should be checked before ordering holders? Verify the inscribed circle (11 mm), thickness (3.18 mm), corner radius (0.4 mm) and clearance angle (11°) to ensure correct holder compatibility with the TPGA110304. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 110304 DX140 Wendeplatten - Tungaloy
Take advantage of the DX140 PCD grade and the ISO-standard triangular form for efficient, high-speed aluminium turning with extended tool life; compatibility with standard holders ensures predictable integration into existing tooling systems. Order the TPGA110304 DX140 Tungaloy indexable insert directly via Metav Werkzeuge or ask our consultants if further advice is needed. TPGA110304 DX140 Tungaloy indexable turning insert — PCD grade, triangular insert, 11° clearance TPGA110304 DX140 Tungaloy is an ISO-standard indexable turning insert engineered for high-speed turning of aluminium, non-ferrous and abrasive non-metal materials. PCD cutting material DX140 for aluminium ISO-standard triangular insert, 60° angle 11° clearance, 3.18 mm plate thickness Cylindrical hole for secure clamping Faster machining and markedly longer tool life for aluminium work The DX140 polycrystalline diamond (PCD) grade provides exceptionally high wear resistance when machining aluminium and other non-ferrous materials. Because PCD has a diamond cutting layer, it supports significantly higher cutting speeds compared with conventional carbide grades while maintaining a fine surface finish. The result is a measurable increase in throughput and a reduction in downtime for insert changes, translating into lower operating costs per component. This combination of PCD and the triangular geometry delivers a dependable balance between performance and predictable lifetime. Stable clamping and repeatable geometry for consistent parts Designed to the ISO indexable insert form, the triangular shape with a nominal 60° included angle and a cylindrical hole offers secure and repeatable clamping in compatible holders. The 11° clearance minimises rubbing on the flank while keeping the cutting edge engaged optimally, which reduces vibration and improves dimensional consistency. Compatibility is determined by insert form, clearance angle, tolerance class, attachment method, size and thickness, so the insert integrates smoothly into standard turning tool systems for reliable results. Carbide substrate with PCD cutting layer for process security The insert combines a diamond cutting layer with a robust carbide substrate to ensure mechanical support and resistance to edge chipping. The 3.18 mm plate thickness and corner radius of 0.4 mm provide a stable cutting edge suited to a range of feed and depth settings, while the PCD layer resists abrasive wear. For machining tasks where abrasive non-metals or high-speed aluminium operations are common, this construction offers a predictable and secure machining window, reducing scrap rates and rework. Application-focused design for production environments This indexable insert is intended primarily for turning operations and is supplied without an integrated chipbreaker (no chipbreaker), allowing selection of cutting geometry and feed strategy to match the component and stability conditions. The TPGA110304 designation indicates the ISO geometry and size; the DX140 grade is optimised for non-ferrous alloys and abrasive materials, enabling very long tool life under appropriate cutting parameters. Choosing the correct holder, clamping torque and cutting data will unlock the full productivity benefits of the grade. For predictable high-speed aluminium turning with long tool life, request the TPGA110304 DX140 Tungaloy insert from Metav Werkzeuge or contact our technical advisors at info@metav-werkzeuge.com / +49 2822 7131930 for guidance on holder compatibility and cutting data Technical Data Article number: 6808776 SKU: 6808776-Tungaloy Manufacturer SKU: TUN6808776 Model series: ISO-Drehwendeschneidplatten Product designation: TPGA110304 DX140 Tungaloy-Wendeplatte Core measurements Insert form size: 11 Plate thickness: 3.18 mm Corner radius: 0.4 mm Clearance angle: 11° Included angle: 60° Design and features Cutting material: polycrystalline diamond (PCD) Grade: DX140 Substrate material: carbide Plate shape: triangular Hole: with cylindrical hole Chipbreaker: none Application: turning FAQ What materials is this insert suitable for? The TPGA110304 DX140 insert is designed for aluminium, non-ferrous metals and abrasive non-metal materials; the PCD cutting layer ensures long life under high cutting speeds. Can this insert be used in standard ISO holders? Yes — the insert follows ISO geometry standards; compatibility depends on holder form, clearance angle, size, thickness and fixing method, so matching to an ISO-compatible turning holder is recommended. Does the insert include a chipbreaker? No — this TPGA indexable insert is supplied without a chipbreaker, allowing process-specific chip control via cutting parameters and toolholder selection. What is the corner radius and how does it affect performance? The corner radius is 0.4 mm, offering a compromise between edge strength and surface finish; a larger radius increases edge robustness, while a smaller radius favours finer finishes. Is the cutting layer a bonded diamond or solid carbide? The cutting material is polycrystalline diamond (PCD) bonded to a carbide substrate, combining wear resistance with mechanical support. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 110304 TH10 Wendeplatten - Tungaloy
Take advantage of a sharp, universal uncoated carbide grade and ISO-standard geometry to ensure low cutting forces and clean surfaces in non‑ferrous turning operations. The combination of a compact 60° triangle shape, a 0.4 mm corner radius and a 3.18 mm plate thickness delivers stable clamping and reliable repeatability — order genuine inserts or consult Metav Werkzeuge for holder compatibility and application advice. TPGA 110304 TH10 — ISO triangle turning insert for Drehen by Tungaloy, uncoated carbide, 60° main angle A TPGA110304 TH10 ISO-standard triangle insert engineered for external and internal turning, offering a sharp, universal uncoated carbide grade suited to non‑ferrous materials and applications requiring low cutting forces and good surface finish TPGA110304 60° triangle insert Uncoated carbide grade TH10 0.4 mm corner radius for versatility 3.18 mm thickness with cylindrical hole Consistent fit with ISO tool systems reduces setup time and errors The insert follows the ISO standard geometry, so compatibility with a toolholder is determined by form, clearance angle, tolerance class, clamping method, size and thickness. This standardisation enables predictable mounting and repeatable positioning, which reduces set‑up time and minimises clamping errors on production lines. For workshops and job shops that run mixed batches, the standard form simplifies inventory planning and ensures the insert integrates smoothly into existing turning systems. Sharp, uncoated grade for low cutting forces and clean surfaces The TH10 grade is an uncoated carbide chosen for its sharp cutting edge and universal performance on non‑ferrous materials. In practice this means lower cutting forces and improved surface quality when turning aluminium, brass or similar alloys. An uncoated edge avoids excess built‑up edge on softer metals and supports predictable chip formation where a fine finish and reduced cutting temperature are priorities. Geometry that balances strength and finish for reliable machining The triangle shape with a 60° included angle provides multiple usable cutting edges per insert while maintaining edge strength. A 0.4 mm corner radius gives a compromise between robust edge life and surface finish, and the 11° relief (clearance) angle helps prevent rubbing during entry. The cylindrical hole and standard clamping interface deliver secure fastening and consistent repeatability under load, while the 3.18 mm plate thickness increases stability during heavy or interrupted cuts. Practical application advice for turning operations Designed for both external and internal turning, the insert is supplied without a chipbreaker, which suits straightforward chip flow in non‑ferrous machining; where chip control is essential, select a matching chipformer and grade to the workpiece and machining conditions. Typical system components include the ISO indexable insert, a compatible external holder or boring bar, a locating pad or clamp set and the appropriate screw. For optimisation of cutting data and holder choice, consult the supplier’s product guidance before first use. For application guidance or to request genuine Tungaloy TPGA110304 TH10 inserts, contact Metav Werkzeuge — our specialists advise on holder compatibility and process optimisation Technical Data Article number: 6808775 SKU: 6808775-Tungaloy Manufacturer SKU: TUN6808775 Model series: ISO-Drehwendeschneidplatten Label: TPGA110304 TH10 Tungaloy-Wendeplatte Dimensions & ratings Plate thickness: 3.18 mm Corner radius: 0.4 mm Relief angle: 11° Included angle: 60° Plate size: 11 mm Hole: with hole Features & applications Material: cemented carbide Grade: TH10 (uncoated) Insert shape: triangular Chipbreaker: without Hole style: cylindrical hole Typical use: turning (external and internal) System: ISO insert compatible with standard holders FAQ What materials is this insert suitable for? The TPGA110304 TH10 insert by Tungaloy is optimised for non‑ferrous materials such as aluminium and brass; the uncoated carbide grade supports low cutting forces and clean surface finishes. How is compatibility with a toolholder determined? Compatibility depends on insert form, relief angle (11°), tolerance class, clamping method, plate size (11 mm) and thickness (3.18 mm); match these parameters to the holder specifications when using the TPGA110304 TH10. How many cutting edges are available per insert? A triangular insert provides three primary cutting edges; the TPGA110304 TH10 can be indexed to present a fresh edge when required. What does 'without chipbreaker' mean for machining? 'Without chipbreaker' indicates the insert does not have a dedicated chip control geometry; for the TPGA110304 TH10 this is suitable for straightforward chip flow in non‑ferrous turning or when a separate chipformer is used. What is the advantage of the 0.4 mm corner radius? A 0.4 mm corner radius balances edge strength and surface finish, offering versatility between light finishing cuts and moderate roughing operations with improved tool life. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 110308 DX140 Wendeplatten - Tungaloy
Take advantage of the combination of PCD cutting performance, ISO compatibility and long tool life to increase throughput and reduce tool changes; order genuine inserts via Metav Werkzeuge or consult their technical advisors for application support. TPGA 110308 DX140 PCD Turning Insert for High‑Speed Turning — Tungaloy A TPGA 110308 DX140 PCD turning insert engineered for external and internal turning of aluminium, non‑ferrous and abrasive non‑metal materials. PCD grade DX140 for aluminium and non‑ferrous metals ISO‑standard triangular insert, 60° geometry Extremely high cutting speeds and long tool life Cylindrical centre hole for secure clamping Boosted productivity through PCD performance The DX140 polycrystalline diamond grade delivers a reliable balance of very high cutting speeds and extended tool life, making it particularly effective for high‑volume aluminium machining. By using a PCD cutting edge, chip wear is significantly reduced and the interval between indexings or insert changes is extended, which lowers the effective tooling cost per part. This benefit is especially relevant where short cycle times and consistent surface finish are required. Reliable fit and secure clamping for consistent results Designed to the ISO‑standard geometry, the triangular insert with its 60° cutting angle and cylindrical centre hole ensures predictable seating and repeatable clamping. Compatibility with the matching external holder or boring bar is defined by form, clearance angle, tolerance class, fixing method, size and thickness, so the system—insert, holder, shim/clamp set and replacement screws—delivers stable cutting conditions and reduced vibration. The result is improved process reliability and reproducible part quality. Application range and process stability for delicate materials The cutting material is polykristalliner Diamant (PCD), optimised in grade DX140 for aluminium, other non‑ferrous metals and abrasive non‑metallic workpieces. The insert’s 0.8 mm corner radius, 11° clearance angle and 3.18 mm thickness combine to offer a balance between edge strength and fine surface generation. Selection of the appropriate chipbreaker (DIA) and grade depending on workpiece alloy and machining strategy ensures stable chip formation and minimises edge build‑up while maintaining the required surface integrity. For specific machining recommendations or to obtain original Tungaloy TPGA 110308 DX140 inserts, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 for direct advice and availability. Technical Data Article number: 6808778 SKU: 6808778-Tungaloy Manufacturer SKU: TUN6808778 Model series: ISO‑Drehwendeschneidplatten Core dimensions Size: 11 mm Thickness: 3.18 mm Corner radius: 0.8 mm Clearance angle: 11° Insert angle: 60° Features & applications Cutting material: polycrystalline diamond (PCD), grade DX140 Chipbreaker: DIA Substrate material: carbide Shape: triangular Centre hole: with cylindrical hole Application: turning (external and internal), suited to aluminium, non‑ferrous and abrasive non‑metal materials FAQ What materials is this insert suitable for? The TPGA 110308 DX140 insert is intended for machining aluminium, other non‑ferrous metals and abrasive non‑metallic materials using its PCD cutting edge and DIA chipbreaker. How does the PCD grade DX140 affect productivity? DX140 provides high cutting speeds and prolonged edge life, so the TPGA 110308 DX140 reduces tool changes and improves throughput in serial aluminium turning. Which holder types are compatible with this insert? Compatibility depends on holder form, clearance angle, tolerance class, fixing method, size and thickness; the insert is ISO‑standard and matches corresponding external holders or boring bars designed for triangular TPGA inserts. What are the key dimensions to check before ordering? Confirm size (11 mm), thickness (3.18 mm), corner radius (0.8 mm) and that the holder accepts a 60° triangular insert with a cylindrical centre hole. Is the insert supplied with fastening screws or clamps? The insert is part of a system that typically includes holder, underlay/clamp set and replacement screws; these items are selected separately to match the seating and fixing requirements. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 160302 BX360 Wendeplatten - Tungaloy
High wear resistance and a CBN cutting grade deliver consistent finishing on hardened components; the ISO TPGA 160302 form and cylindrical hole enable reliable clamping in standard holders. Order via Metav Werkzeuge or consult the technical team for tailored cutting parameters. TPGA 160302 BX360 ISO turning indexable insert for hardened steels — Tungaloy The TPGA 160302 BX360 is an ISO-format turning insert designed for finish turning of hardened steels and, depending on execution, for certain cast-iron applications. CBN grade BX360 for hardened steels ISO TPGA 160302 compatibility Triangle 60° form with 0.2 mm nose radius Cylindrical hole for secure clamping Consistent finishing on hardened components The insert combines a CBN cutting surface in the BX360 grade with a carbide substrate, producing high wear resistance and thermal stability that suit abrasive, high-hardness finishing passes. The use of cubic boron nitride is particularly advantageous for sustained tool life when machining hardened steels, since the material maintains cutting-edge integrity where conventional coatings would break down. This results in predictable surface quality and reduced frequency of insert changes, supporting efficient process planning in series production. Seamless integration into ISO tooling systems Compliance with the ISO TPGA geometry means the plate fits a wide range of standard external holders when form, relief, tolerance class, fixation, size and thickness match. The 11° relief angle and 3.18 mm thickness are decisive positioners for support and clamping; matching these parameters minimises chatter and improves repeatability. For production environments, this compatibility reduces setup time and simplifies spare-part stocking, enabling faster tool changes and steady throughput. Precision and surface quality from a small nose radius A 0.2 mm nose radius on a triangle plate with a 60° included angle concentrates cutting forces for fine finish passes and dimensional control. With the insert specified without a chipbreaker, the geometry is optimised for final machining and light cuts where chip form is managed by cutting data and coolant strategy rather than a pronounced groove. The TPGA form therefore supports high-quality finishes on shoulders and profiles where minimal allowance and tight tolerances are required. Practical handling and system composition for production The TPGA system is built from the indexable insert plus a suitable holder, a clamping set or shim and replacement screws; the insert’s cylindrical hole ensures secure, repeatable seating. Intended for both external and internal turning, the grade selection and presence or absence of a chipbreaker should be matched to material and process stability. For mixed batches that include hardened parts and certain cast irons, BX360 offers broad performance; for different cutting strategies, consider alternative grades or geometries to balance life and surface finish. For specification support, stock information or application recommendations for the Tungaloy TPGA 160302 BX360 insert, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 to speak with a technical consultant. Technical data SKU: 6808780-Tungaloy Manufacturer SKU: TUN6808780 Manufacturer article number: 6808780 Model series: ISO turning indexable inserts Facts Inscribed circle / size: 16 mm Thickness: 3.18 mm Nose radius: 0.2 mm Relief angle: 11° Included angle: 60° Manufacturer SKU: TUN6808780 Special features CBN cutting material BX360 Carbide substrate Triangle plate form With cylindrical hole Without chipbreaker For turning operations Suitable for hardened steels ISO TPGA 160302 compatibility FAQ What materials is this insert intended for? The TPGA 160302 BX360 insert (Tungaloy, SKU TUN6808780) is primarily specified for hardened steels and, depending on its exact execution, can be used for certain cast-iron applications. Is the insert suitable for finish machining? Yes — the BX360 CBN grade and a 0.2 mm nose radius are optimised for finishing passes where surface quality and dimensional accuracy are priorities. How is the insert fixed in the holder? Fixing relies on ISO-compatible geometry and the cylindrical hole; proper matching of form, relief angle, tolerance and clamping set ensures stable seating and repeatable positioning. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 160302 DX140 Wendeplatten - Tungaloy
Benefit from the combination of PCD cutting material, exceptional wear resistance and ISO compatibility for a reliable turning process; the DX140 grade enables sustained high cutting speeds and long tool life. Order the insert directly via Metav Werkzeuge or consult the Metav specialists for cutting data and holder compatibility. TPGA160302 DX140 — TPGA triangular turning insert, PCD grade (Tungaloy) The TPGA160302 DX140 is a triangular ISO turning insert designed for high‑speed machining of aluminium, non‑ferrous metals and abrasive non‑metallic materials. PCD grade DX140 for high wear resistance Optimised for high cutting speeds ISO triangular shape, 60° included angle Compatible with ISO turning holders Consistent high performance for aluminium and non‑ferrous machining The TPGA160302 DX140 combines a polycrystalline diamond (PCD) cutting layer with a robust carbide body to deliver very low flank wear when machining abrasive or non‑ferrous materials. The PCD grade DX140 is engineered for high cutting speed applications and preserves edge sharpness over extended production runs, which reduces the frequency of index changes and boosts process uptime. This makes the insert particularly suited to long series where surface finish and repeatability matter. Straightforward integration into ISO turning systems With an ISO TPGA geometry and a 60° included angle, the insert fits standard ISO turning holders provided form, clearance angle, tolerance class, clamping method, size and thickness match the holder specifications. The combination of a triangular shape and a corner radius 0.2 mm allows secure clamping and predictable chipflow for external and internal turning operations. Compatibility with common holder styles simplifies tool assortment and shortens setup time on the shop floor. Practical benefits: economy and predictability Using a PCD‑tipped insert such as this reduces unplanned downtime thanks to long tool life and stable wear behaviour; one or two tool changes per batch can often replace multiple carbide inserts under similar cutting conditions. The 3.18 mm plate thickness provides adequate mechanical support for the PCD layer while maintaining a compact insert package that minimises overhang and vibration for improved surface quality. Application guidance and selection tips Select the DX140 grade and an appropriate chipformer based on workpiece material, cutting parameters and machine rigidity. Although this insert is supplied without a chipbreaker, pairing it with the correct feed and depth of cut yields controlled chips and consistent results in aluminium and other non‑ferrous alloys. Where holder compatibility is uncertain, verify form and clamping details against the ISO standard to ensure safe, repeatable operation. For machining requirements involving Tungaloy PCD inserts, contact Metav Werkzeuge to request cutting data, confirm holder compatibility or obtain recommendations tailored to specific aluminium or non‑ferrous applications — eMail: info@metav-werkzeuge.com / Tel: +49 2822 7131930 Technical data Article number: 6808779-Tungaloy Manufacturer article number: 6808779 Manufacturer SKU: TUN6808779 Model series: ISO turning inserts WPL designation: TPGA160302 DX140 Facts Corner radius: 0.2 mm Plate size: 16 mm Plate thickness: 3.18 mm Relief angle: 11° Included angle: 60° Special features Cutting material: DX140 polycrystalline diamond (PCD) Body material: carbide Plate shape: triangular Hole: with cylindrical hole Chipbreaker: without chipbreaker Application: turning; suited to aluminium, non‑ferrous metals and abrasive non‑metallics ISO‑standard geometry; compatible with corresponding ISO holders FAQ What materials is this insert best suited for? The TPGA160302 DX140 insert is optimised for aluminium, non‑ferrous metals and abrasive non‑metallic materials thanks to its DX140 PCD cutting layer and carbide support. Does the insert require a specific holder type? Compatibility depends on holder form, clearance angle, tolerance class, clamping method, size and thickness; the TPGA160302 follows ISO geometry and is intended for ISO turning holders meeting those specifications. Is a chipbreaker included with the insert? This variant is supplied without a chipbreaker; chip control is achieved through appropriate feeds, depths of cut and holder selection. What advantages does the DX140 grade offer over conventional carbide tips? DX140 PCD provides higher wear resistance and extended service life at high cutting speeds, which improves process stability and reduces tool change frequency in suitable materials. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
TPGA 160304 BX360 Wendeplatten - Tungaloy
Take advantage of the combination of CBN wear resistance, ISO compatibility and a compact 0.4 mm corner radius for consistent finish turning of hardened components. Order the insert directly via Metav Werkzeuge or consult our advisers for application-specific setup and stock availability. TPGA 160304 BX360 turning insert by Tungaloy — CBN grade for hardened steels The TPGA160304 BX360 turning insert is an ISO-standard triangular insert designed for precision external and internal turning of hardened steels and, depending on specification, cast iron. CBN grade BX360 for hardened steels ISO TPGA160304 triangular insert form 0.4 mm corner radius for precision finishes Cylindrical hole for secure clamping High-wear performance for demanding finishing operations The TPGA160304 BX360 is manufactured to deliver high abrasion resistance through its CBN cutting material and the BX360 grade. This combination is intended for end finishing and high-hardness turning where tool life and surface quality are critical. By using cubic boron nitride as the cutting medium, the insert offers significantly greater resistance to flank wear compared with conventional carbide tools when machining hardened steels. The result is more consistent part geometry and reduced need for frequent tool changes, supporting uninterrupted production and predictable downtime planning. Reliable fit in ISO systems for straightforward tool interchangeability Compatibility with the toolholder is defined by the insert geometry, ISO-standard designation, relief angle and fastening method. The triangular triangular form and the cylindrical hole ensure consistent seating and repeatable location in standard TPGA-style holders. Because tolerance class, size and thickness are standardised, the insert can be integrated into existing tool systems without modifying fixtures, which simplifies inventory management and reduces setup time for changeovers. Precise finishing and surface integrity from optimised edge form The 0.4 mm corner radius supports smooth material flow at the cutting edge and contributes to a fine surface finish in finishing cuts. For high-hardness materials the CBN edge maintains dimensional stability under thermal and mechanical stress, producing fewer vibrations and a reduced tendency for built-up edge. In practice this means fewer rework steps and an improved first-pass yield when finishing bearing seats, shafts or other components requiring tight tolerances and consistent surface quality. Practical considerations for secure clamping and process reliability The insert is supplied in a form that requires a compatible outer holder or boring bar, a suitable clamping pad or clamp set, and the correct fastening screw. Selection of the holder and stability of the assembly are decisive for the achievable feed rates and surface finish; a rigid setup extends insert life and enables higher metal removal rates for roughing-to-finishing sequences. If additional machining parameters or holder recommendations are needed, documented cutting data can be provided to align the insert with machining centre capability and the chosen process window. For applications that demand stable, repeatable finishing of hardened parts, contact Metav Werkzeuge to discuss the Tungaloy BX360 CBN insert and to arrange supply or technical consultation Technical Data Article number: 6808784 Manufacturer SKU: TUN6808784 Vendor SKU: 6808784-Tungaloy Model series: ISO-Drehwendeschneidplatten Material: cemented carbide Facts ISO designation: 160304 Insert form: triangular Corner radius: 0.4 mm Relief angle: 11° Plate thickness: 3.18 mm Plate size: 16 mm Wedge angle: 60° Special features Cutting material: cubic boron nitride (CBN), grade BX360 Mounting: with cylindrical hole for secure clamping Typical application: external and internal turning of hardened steels; possible use on cast iron depending on grade System components: insert, compatible outer holder or boring bar, clamping pad/kit and replacement screws FAQ What materials is this insert best suited for? The TPGA160304 BX360 insert is optimised for hardened steels and, in specific variants, for cast iron; the CBN cutting material ensures strong wear resistance on high-hardness workpieces. How does the BX360 grade affect tool life? BX360 is a CBN grade designed for wear-intensive finishing; the BX360 formulation prolongs tool life in comparison with conventional grades when machining hard materials. Is the insert compatible with standard TPGA holders? Yes, the ISO designation and the cylindrical hole permit seating in standard TPGA holders, but compatibility also depends on holder form, tolerance class and clamping method. What surface finish can be expected with a 0.4 mm corner radius? A 0.4 mm radius supports fine finishing passes and contributes to stable cutting conditions that typically yield improved surface integrity and reduced need for rework. Are replacement screws and clamping pads required for installation? A complete system includes the insert, a matching holder or boring bar, the appropriate clamping pad or clamp kit, and the correct replacement screws to ensure secure fastening and repeatable indexing. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 160304 DX140 Wendeplatten - Tungaloy
Benefit from the combination of PCD-grade DX140 and ISO triangular geometry for high-speed aluminium turning with significantly extended tool life; order directly via Metav Werkzeuge or contact our advisors for application support. TPGA160304 DX140 TPGA turning insert by Tungaloy — PCD grade for high-speed aluminium and non-ferrous turning The TPGA160304 DX140 is an ISO triangular indexable insert designed for high-speed external and internal turning of aluminium and other non-ferrous materials with excellent wear resistance Polycrystalline diamond (PCD) grade DX140 Optimised for aluminium and non-ferrous metals ISO triangular 60° geometry, 0.4 mm radius Compatibility with standard ISO turning holders High-speed aluminium turning with predictable tool life The combination of polycrystalline diamond (PCD) cutting material and the DX140 grade provides a clear productivity advantage when machining aluminium and abrasive non-metallic materials. The insert’s PCD layer resists abrasive wear and preserves a sharp cutting edge, which allows for high cutting speeds and consistent surface finish over extended runtimes. For production environments this translates into fewer insert changes, lower downtime and a reduced cost per component compared with conventional carbide solutions. Geometry and edge form that support consistent accuracy A triangular insert with a 60° included angle and a 0.4 mm corner radius offers a balance between edge strength and formability, enabling accurate profiling and light-radius turning operations. The nominal 11° clearance and standard ISO dimensions ensure stable seating in matching holders, while the carbide substrate provides the mechanical support required under interrupted cuts. Together, these features produce reproducible results and reduce the need for frequent rework in precision machining tasks. Application guidance and system compatibility for reliable setup The insert is supplied as an ISO-format turning grade intended for use with compatible external holders, boring bars and clamping sets; compatibility is determined by form, clearance angle, tolerance class, fixing method, size and thickness. As a solution for aluminium and non-ferrous parts, this PCD-tipped insert eliminates built-up edge and improves chip flow, particularly when machining abrasive or glass-filled materials. For bespoke setups, match holder geometry and clamping torque to maintain stability and reach the expected service life. Operational benefits and process optimisation Using a PCD insert of this specification reduces frequency of tool changeovers and improves process stability, especially in continuous production. The long-lasting cutting edge decreases inventory turnover for spare inserts and minimises machine idle time. When applied correctly, the DX140 grade contributes to a consistent surface finish and reliable dimensional control, helping to meet tighter tolerances with fewer corrective operations. Contact Metav Werkzeuge for application advice, availability and to discuss DX140 PCD inserts for high-speed aluminium turning — info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 6808783 Manufacturer SKU: TUN6808783 Model series: ISO turning indexable inserts Type designation: TPGA160304 Core specifications Size: 16 mm Thickness: 3.18 mm Corner radius: 0.4 mm Included angle: 60° Clearance angle: 11° ISO code: 160304 Materials & features Substrate material: carbide Cutting material: polycrystalline diamond (PCD), grade DX140 Plate shape: triangular Hole: with cylindrical hole Chipbreaker: none Application: turning (external and internal) Typical use: aluminium and non-ferrous metals; abrasive non-metals FAQ What materials is this insert best suited to? The TPGA160304 DX140 insert is engineered for aluminium, non-ferrous metals and abrasive non-metallic materials, where the PCD cutting surface delivers long life and excellent finish. How does the DX140 grade affect machining performance? DX140 is a PCD grade formulated for high wear resistance and stability; when used in the correct holder and cutting conditions, the grade extends tool life and supports higher cutting speeds. Which holders are compatible with this ISO insert? Compatibility depends on holder form, clearance angle, tolerance class, fixing method, size and thickness; use standard ISO turning holders designed for TPGA-style triangular inserts. Is a chipbreaker included on the insert? This insert is supplied without a chipbreaker; chip control must be addressed via cutting parameters, tool overhang and coolant strategy where applicable. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 160304 NS9530 Wendeplatten - Tungaloy
Take advantage of the finishing-grade NS9530 uncoated cermet and its low cutting forces combined with ISO compatibility for reliable, high-quality turning operations; order the inserts directly via Metav Werkzeuge or contact the consultants for application advice. TPGA160304 NS9530 triangular indexable insert for turning — Tungaloy The TPGA160304 NS9530 is an ISO-standard triangular indexable insert designed for precision finishing in turning applications, optimised for steel finishing with a sharp cutting edge and continuous-cut conditions. ISO triangular insert TPGA160304, 60° geometry Uncoated cermet grade NS9530 for fine finishing Low cutting forces and sharp cutting edge Compatible with ISO turning holders, with cylindrical hole Achieve superior surface finish with a dedicated finishing grade The insert is manufactured as an uncoated cermet finishing grade, NS9530, tailored for low-force cutting and consistent surface quality when turning steel. Thanks to the sharp cutting edge and the material composition based on a carbide substrate with cermet cutting edges, the geometry produces reduced rubbing and minimal built-up edge during continuous cuts. This results in a measurable improvement in component finish and can reduce downstream polishing or grinding operations, enhancing cycle-time efficiency without compromising dimensional control. Secure mounting and ISO compatibility for predictable clamping Designed to conform to ISO turning insert standards, the plate’s triangular form and 60° included angle ensure broad holder compatibility. The insert features a cylindrical hole for positive axial locating and repeatable clamping, paired with a defined 11° relief angle that supports stable cutting engagement. These characteristics simplify tool-room stocking and reduce setup variations, since holders can be matched by form, free angle, tolerance class, fastening method, size and thickness to guarantee correct seating and secure fixation during machining. Improve productivity through reduced cutting forces and stable cutting With a corner radius of 0.4 mm and a plate thickness of 3.18 mm, the geometry is optimised for small depths of cut and continuous finishing passes. The combination of sharp geometry and the cermet grade leads to low cutting forces and consistent edge condition, which contributes to longer insert life in finishing cycles and stable process windows. Selecting the correct chipbreaker and matching the grade to the workpiece material and machining stability will further enhance cycle consistency and part quality, delivering measurable productivity gains in serial production. Practical system considerations for integration into your toolset The ISO-series system approach means the indexable plate is part of a wider system comprising a compatible external holder or boring bar, a backing pad or clamping set, and replacement screws. When replacing or stocking inserts, the standardised designation eases identification: size 16, triangular sheet, thickness 3.18 mm, with a cylindrical mount hole and an included angle of 60°. This clarity reduces tooling errors and supports a predictable spare-part strategy in the workshop or on the shop floor. Contact Metav Werkzeuge for tailored application support on the Tungaloy TPGA160304 NS9530 insert and to confirm optimal holder selection; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6998024 Manufacturer SKU: TUN6998024 SKU: 6998024-Tungaloy Designation: TPGA160304 NS9530 Series: ISO turning indexable inserts Material: carbide Facts Corner radius: 0.4 mm Relief angle: 11° Insert size: 16 mm Thickness: 3.18 mm Included angle: 60° Special features Uncoated cermet grade NS9530 Finishing grade for steel with sharp cutting edge With cylindrical mounting hole Triangular plate form, no chipbreaker Suitable for continuous cut and small depths of cut FAQ What materials is this insert suitable for? The TPGA160304 NS9530 insert is designed primarily as a finishing grade for steel and performs best in continuous turning operations on steel workpieces. Does the insert fit standard ISO turning holders? Yes, the triangular geometry and ISO designation ensure compatibility with ISO-standard turning holders when form, free angle and size match; confirm holder specifications before use. What is the corner radius and how does it affect the finish? The insert has a corner radius of 0.4 mm, which supports fine surface finishes and is appropriate for small-depth finishing passes. Is there a coating on the cutting edge? No, the NS9530 is supplied as an uncoated cermet finishing grade to provide a sharp edge and low cutting forces for improved surface quality. What is the manufacturer SKU and article reference for procurement? The article number is 6998024 and the manufacturer SKU is TUN6998024 for the TPGA160304 NS9530 triangular indexable insert. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 160304 TH10 Wendeplatten - Tungaloy
Take advantage of the combination of ISO‑standard compatibility, a sharp TH10 uncoated carbide grade and a compact 0.4 mm corner radius for efficient, low-force turning of non-ferrous materials; order the TPGA160304 TH10 Tungaloy insert directly via Metav Werkzeuge or ask our consultants if needed. TPGA 160304 TH10 – Indexable turning insert (Turning) by Tungaloy TPGA160304 TH10 Tungaloy‑Wendeplatte is an ISO‑standard triangular indexable insert designed for general turning applications, especially where low cutting forces and clean surfaces are required ISO‑standard triangular insert Universal TH10 uncoated carbide grade 11° clearance angle for stable cutting Central cylindrical hole for secure clamping Consistent performance for productive turning operations The uncoated carbide composition of this indexable insert provides predictable wear behaviour and reduced cutting forces, making it especially suitable for machining non‑ferrous materials and mixed batches. The combination of a sharp universal grade TH10 and the ISO‑standard interface ensures compatibility with a wide range of holders; the result is reliable chip control and repeatable part quality. This technical setup supports a high material removal rate where low cutting resistance and a clean surface finish are priorities. Accurate geometry that supports surface quality and tool life A defined 0.4 mm corner radius and an 11° clearance angle create a cutting edge geometry that balances strength and finish: the corner radius helps to distribute cutting loads and reduce edge chipping, while the clearance angle minimises rubbing and heat buildup. The triangular geometry with a central cylindrical hole provides stable clamping and easy indexing, reducing downtime during tool changes and supporting consistent cycle times across production runs. Practical benefits and application guidance for workshops Designed for external and internal turning, the insert features a 16 mm inscribed circle and a plate thickness of 3.18 mm, offering a compact solution where space and rigidity are factors. The absence of a dedicated chipbreaker makes this insert best suited to applications where the workpiece material and cutting parameters naturally produce manageable chips; for other situations, pairing the insert with an appropriate holder and cutting strategy will deliver the intended productivity and surface quality. Compatibility depends on holder form, relief angle, tolerance class, fastening method, size and thickness. For reliable, high‑productivity turning with Tungaloy quality, contact Metav Werkzeuge for ordering and technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: 6808782 Manufacturer SKU: TUN6808782 Internal SKU: 6808782-Tungaloy Model series: ISO‑Drehwendeschneidplatten Designation: TPGA160304 TH10 Tungaloy‑Wendeplatte Facts Inscribed circle: 16 mm Thickness: 3.18 mm Corner radius: 0.4 mm Clearance angle: 11° Included angle: 60° Hole: cylindrical, with central hole Special features Material: uncoated carbide (Hartmetall) Grade: TH10, sharp universal grade for non‑ferrous materials Plate shape: triangular Chipbreaker: none Compatibility: ISO‑standard insert; fits holders matched by form, relief, tolerance, fastening, size and thickness FAQ What materials is this insert best suited for? The TPGA160304 TH10 Tungaloy insert is optimised for non‑ferrous materials and mixed batches where an uncoated carbide cutting edge supports low cutting forces and a clean surface finish. How is the insert clamped in the holder? Clamping is achieved via a central cylindrical hole and the ISO‑standard geometry; the triangular form and 11° relief ensure secure indexing in compatible turning holders. Can this insert be reused by indexing? Yes, the triangular geometry provides multiple cutting edges; the TPGA160304 TH10 insert can be indexed to a fresh edge as part of standard tool maintenance procedures. What factors determine compatibility with a toolholder? Compatibility depends on holder form, clearance/relief angle, tolerance class, fastening method, insert size and thickness; matching these parameters ensures correct fit and repeatable performance with the TPGA160304 TH10. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGA 160308 BX360 Wendeplatten - Tungaloy
Take advantage of the combination of CBN cutting performance, precise geometry and ISO compatibility for reliable finishing of hardened components; order directly via Metav Werkzeuge or request consultancy for machining setup. TPGA160308 BX360 TPGA ISO 160308 triangular indexable insert for turning — Tungaloy The TPGA160308 BX360 is an ISO triangular indexable insert designed for turning applications, optimised for wear‑intensive finishing of hardened steels and, depending on variant, cast iron. CBN grade BX360 for hardened steels ISO TPGA 160308 triangular format 0.8 mm nose radius for fine finishing With cylindrical hole, 11° clearance angle High‑performance finishing of hardened components The insert uses cubic boron nitride (CBN) technology, coded as BX360, which is developed specifically for wear‑intensive finishing of high‑hardness steels. CBN provides a combination of abrasion resistance and edge stability that translates into consistent surface quality and longer tool life under finishing conditions. The grade is engineered to retain a sharp cutting edge when machining demanding materials, helping to reduce downtime for insert changes and to maintain dimensional stability across runs. Precise geometry and mounting for predictable results Compatibility with the workholding system is determined by form, clearance angle (11°), tolerance class, fastening method, size and thickness. The insert is supplied in the ISO TPGA format with a 60° included angle, triangular profile and a 0.8 mm nose radius, together with a cylindrical hole for secure clamping. The 3.18 mm plate thickness and 16 mm inscribed circle ensure the insert sits correctly in matching holders; secure, repeatable seating reduces vibration and supports consistent chip flow even without an integrated chipbreaker. Substrate and application guidance for efficient machining The construction combines a hard carbide substrate with a CBN cutting layer, delivering a balance between toughness and hardness suitable for finishing operations. The insert is intended for external and internal turning where high hardness and wear demand specialist grades; selection of the correct chipformer and cutting parameters should be aligned with workpiece material, operation type and machine stability. In stable setups, the absence of a chipbreaker on this variant can aid in producing an even, controlled cut and excellent surface finish for typical end‑of‑line machining. For precision finishing of hardened steels, request availability of the Tungaloy BX360 TPGA160308 from Metav Werkzeuge and obtain tailored machining advice at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: 6808787 Manufacturer SKU: TUN6808787 Label: TPGA160308 BX360 Tungaloy‑Wendeplatte Facts ISO code: 160308 Insert size (inscribed circle): 16 mm Plate thickness: 3.18 mm Nose radius: 0.8 mm Included angle: 60° Clearance angle: 11° Hole: with hole (cylindrical) Special features Grade: BX360 Cutting material: cubic boron nitride (CBN) Substrate material: carbide Shape: triangular Chipbreaker: none Typical application: turning; external and internal finishing Series: ISO turning indexable inserts Compatibility determined by form, clearance angle, tolerance, fastening, size and thickness FAQ Which materials are suitable for this insert? The TPGA160308 BX360 insert from Tungaloy is intended primarily for high‑hardness steels and, depending on the specific variant, for certain cast irons; the CBN cutting material targets wear‑intensive finishing tasks. Does this variant include a chipbreaker? This TPGA160308 BX360 variant is supplied without an integrated chipbreaker, which makes it most suitable for stable setups where controlled cutting conditions and edge integrity are preferred. How is compatibility with holders ensured? Compatibility depends on ISO format, the 60° triangular geometry, the 11° clearance angle, plate thickness and the cylindrical hole; matching holder form and tolerance class ensures secure clamping and repeatable positioning. What does the BX360 grade indicate? BX360 denotes a Tungaloy CBN grade formulated for high wear resistance and stable edge life in finishing operations on hardened steels, prioritising consistent surface quality and extended intervals between insert changes. Can this insert be used for internal turning? Yes, the TPGA160308 geometry is suitable for both external and internal turning operations provided the holder and machine setup deliver the required rigidity and the cutting parameters are adapted for hardened materials. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
TPGA 160308 DX140 Wendeplatten - Tungaloy
Combining PCD durability with ISO compatibility, the insert delivers exceptionally long tool life and enables high cutting speeds in non‑ferrous turning operations. Order the TPGA160308 DX140 directly via Metav Werkzeuge or ask our consultants if needed. TPGA160308 DX140 turning insert by Tungaloy — ISO triangular insert for non‑ferrous machining The TPGA160308 DX140 is an ISO‑format turning insert designed for external and internal turning of aluminium, non‑ferrous metals and abrasive non‑metals, providing high‑speed performance and extended life. PCD grade DX140 for abrasive materials ISO‑standard triangular insert 16 mm Suitable for high cutting speeds Cylindrical hole for secure clamping Optimised high‑speed performance for non‑ferrous turning The insert is engineered around a polycrystalline diamond (PCD) cutting layer, graded DX140, which is specified for high abrasiveness and aggressive feed rates. This combination results in very long tool life and reduced tool change frequency, improving uptime in serial production. The cutting concept is particularly efficient for aluminium and non‑ferrous alloys, where the hard PCD surface maintains a sharp edge at elevated speeds and resists abrasive wear from non‑metallic inclusions. Precise geometry and measurable advantages in set ups Compatibility with ISO holders is defined by form, clearance angle, tolerance class, attachment method, size and thickness, and this insert follows ISO conventions to simplify tool‑planning. Key geometry data such as a 16 mm inscribed circle, 0.8 mm corner radius and 3.18 mm thickness enable predictable cutting forces and surface finish. Using standardised inserts reduces set‑up time and ensures interchangeability across machines and carriers, making process planning more reliable. Secure clamping and stable machining behaviour The insert comes with a cylindrical hole, allowing controlled clamping and repeatable positioning relative to the toolholder. A triangular plate form with a 60° included angle and 11° clearance provides a stable cutting edge engagement and predictable chip formation when matched to an appropriate holder and feed strategy. Where surface quality and dimensional control matter, the stable geometry helps maintain concentricity and reduces vibration-induced deviation. Application focus and practical benefits on the shop floor Designed for turning, this insert performs best in applications requiring efficient removal of aluminium, brass and abrasive non‑metallic compounds. The absence of a chipbreaker means chip control relies on correct feed rates and holder geometry; this allows process engineers to tailor chip formation to machine capacity and workpiece geometry. The result is improved productivity through fewer interruptions and consistent component quality across batches. For high‑speed non‑ferrous turning applications, contact Metav Werkzeuge to request the Tungaloy TPGA160308 DX140 insert and receive tailored technical guidance via info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Manufacturer article number: 6808786 Manufacturer SKU: TUN6808786 SKU: 6808786-Tungaloy Model series: ISO turning inserts Core specifications Inscribed circle: 16 mm Corner radius: 0.8 mm Thickness: 3.18 mm Clearance angle: 11° Wedge/included angle: 60° Materials & special features Material: carbide Cutting material: polycrystalline diamond (PCD), DX140 grade Plate form: triangular Hole: cylindrical hole (with hole) Chipbreaker: without Application: turning (external and internal) Typical use: aluminium, non‑ferrous metals, abrasive non‑metals ISO‑standard insert; compatibility determined by form, clearance angle, tolerance class, attachment, size and thickness FAQ What materials is this insert suitable for? The TPGA160308 DX140 insert is designed for aluminium, other non‑ferrous metals and abrasive non‑metallic materials, utilising its PCD cutting layer for high wear resistance. Does the insert require a specific holder type? Compatibility is defined by ISO form, clearance angle, tolerance class, attachment method, size and thickness; the insert is intended for holders matching the ISO TPGA form. Can the insert be used at high cutting speeds? Yes, the DX140 PCD grade is formulated for elevated cutting speeds typical in non‑ferrous turning, delivering extended life under suitably optimised conditions. How does the cylindrical hole affect clamping? The cylindrical hole allows secure, repeatable clamping and precise positioning in compatible toolholders, contributing to consistent machining performance. Is a chipbreaker integrated into the insert design? This variant is supplied without a chipbreaker, so chip control is achieved via appropriate feed, depth of cut and holder geometry. Manufacturer/Responsible: Tungaloy‑NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
TPGA 160308 TH10 Wendeplatten - Tungaloy
Take advantage of a sharp, uncoated carbide grade that supports low cutting forces and clean surfaces while maintaining ISO compatibility for straightforward holder integration. Combine the TH10 grade's universal cutting behaviour with a compact 0.8 mm corner radius and reliable clamping features for smooth production flow. Order the TPGA160308 TH10 insert directly via Metav Werkzeuge or ask our consultants if needed. TPGA160308 TH10 — TPGA ISO turning insert, uncoated carbide, 60° (Tungaloy) The TPGA160308 TH10 is an ISO-format indexable turning insert designed for external and internal turning, optimised for non‑ferrous materials and applications requiring a clean, low‑force cut ISO-format triangular insert, 60° geometry Uncoated carbide grade TH10 for low cutting forces 0.8 mm corner radius for balanced edge strength Cylindrical hole and 3.18 mm plate thickness for secure clamping Productive turning with an uncoated universal grade The combination of an uncoated carbide cutting edge and the TH10 grade delivers a universally useful solution for machining non‑ferrous alloys and cases where a clean surface finish is crucial. The sharp, uncoated edge helps to reduce cutting forces and limits built‑up edge formation on softer materials, which can improve dimensional stability and surface quality. As an ISO-format insert, the component integrates into established tool systems; compatibility is dictated by holder geometry, relief angle, tolerance class, fastening style, size and thickness, so the insert can be matched precisely to the chosen tool holder for predictable results. Robust geometry for consistent edge life and surface quality A triangular shape with a 60° included angle provides multiple indexed cutting edges and good accessibility for both external and internal turning operations. The 0.8 mm corner radius strikes a pragmatic balance between edge robustness and achievable surface finish: it supports moderate feed rates while maintaining a resistant cutting edge in interrupted or less stable cuts. The insert’s 3.18 mm plate thickness and cylindrical hole ensure reliable clamping and repeatable positioning, helping to reduce vibration and improve tool life even when working close to tolerance limits. Note that this variant is supplied without a chipbreaker, making it best suited to applications where a sharp, unobstructed cutting profile is preferred. System considerations and workflow benefits Integrating this insert into a production setup is straightforward: the typical system comprises an ISO insert, a matching external holder or boring bar, a suitable shim/clamp set and spare screws. Selecting the correct chipformer and grade for the workpiece material and the machining stability remains essential for optimised performance, but the universal nature of this grade simplifies inventory and reduces the number of specialised items required. The geometry and ISO conformity enable fast changeovers and consistent process parameters across different machines, contributing to higher throughput and predictable, repeatable results. For application advice, availability or to request compatible holder recommendations for Tungaloy inserts, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our consultants will assist with selection and supply. Technical Data Article number: 6808785 Manufacturer SKU: TUN6808785 Brand: Tungaloy Designation: TPGA160308 TH10 Facts Corner radius: 0.8 mm Included angle: 60° Relief angle: 11° Plate thickness: 3.18 mm Plate size: 16 mm Special features Material: carbide, uncoated Plate form: triangular Hole: cylindrical Chipbreaker: none Application: turning (external and internal) ISO-format insert Compatibility: holder form, relief angle, tolerance class, fastening, size and thickness System components: holder, shim/clamp set, spare screws FAQ What materials is this insert best suited for? The TPGA160308 TH10 insert is designed primarily for non‑ferrous materials and situations where an uncoated cutting edge promotes low cutting forces and a clean surface finish. Is the TPGA160308 TH10 coated? No, this insert is supplied as an uncoated carbide grade (TH10) to provide a sharp edge and lower cutting resistance for the intended material range. What are the key geometry specifications of the insert? The insert features a 60° included angle and a 0.8 mm corner radius, with a plate thickness of 3.18 mm, which together deliver balanced edge strength and accessibility. How can compatibility with a holder be ensured? Compatibility is determined by the holder’s form, relief angle, tolerance class, fastening method, size and thickness; check these parameters against the insert’s ISO designation before assembly. Can this insert be used for internal turning? Yes, the ISO-format design and triangular geometry allow use in both external and internal turning when paired with a suitable boring bar or holder. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand‑new product from the manufacturer.
TPGH 080202 GT9530 Wendeplatten - Tungaloy
Take advantage of the combination of durable GT9530 coated cermet, precise 60° triangular geometry and a small 0.2 mm corner radius for consistent finishing and extended tool life; order directly via Metav Werkzeuge or request machining data from our specialists. TPGH 080202 GT9530 turning insert (Tungaloy) — Coated cermet, 60° triangular geometry TPGH080202L-W10 GT9530 Tungaloy insert offers a wear-resistant finishing grade for stable steel turning operations, optimised for surface quality and extended runtimes Coated cermet grade GT9530 Triangular ISO 60° geometry Designed for finishing and light universal turning 0.2 mm corner radius for refined edges High-performance finishing that raises productivity The GT9530 coating on a cemented carbide substrate delivers reliable finishing performance in stable turning setups. The coated cermet grade is designed to combine good surface quality with longer tool life, which reduces downtime for insert changes and contributes to predictable cycle times. In tandem with the triangular 60° geometry, the cutting edges provide repeatable engagement and consistent chip formation, helping to maintain part tolerances across batches. Proven compatibility and straightforward system integration As an ISO-standardised indexable insert, the component suits standard holders and boring bars when form, clearance, tolerance class, fixing method, size and thickness match. The insert’s cylindrical hole with one-sided countersink (70°–90°) ensures secure clamping and straightforward replacement in modular tool systems. When assembled with a compatible external holder and the correct clamping accessories, the system supports reliable repeatability and fast set-up routines for turning tasks. Material and coating explained for informed machining decisions The term coated cermet refers to a ceramic–metal composite with a surface layer that improves wear resistance and thermal stability. For finishing operations in steel, this combination balances edge strength and surface preservation, so the GT9530 grade is particularly suitable where a fine finish and longer edge life are required. The 0.2 mm corner radius moderates cutting forces and helps avoid edge chipping at light depths of cut, while retaining the geometry needed for accurate profiling. Practical application advice and process benefits Used for both external and internal turning, the insert’s W10 chipbreaker is matched to finishing and light general-purpose cuts under stable conditions. The moderate 11° clearance supports smooth entry and effective chip evacuation without excessive rubbing. Selecting this insert as part of a matched tool system can reduce scrap rates and improve surface finish consistency. For advice on feeds, speeds and holder pairing, Metav Werkzeuge can supply recommended cutting data tailored to the material and machine rigidity. Contact Metav Werkzeuge for tailored cutting data, holder compatibility checks and fast delivery of Tungaloy inserts; call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 6997889 SKU: 6997889-Tungaloy Manufacturer SKU: TUN6997889 Model series: ISO-Drehwendeschneidplatten Product name: TPGH080202L-W10 GT9530 Numbers / Core technical data Geometry angle: 60° Thickness: 2.38 mm Corner radius: 0.2 mm Clearance angle: 11° Plate size: 08 Special features / Designs Coating/grade: GT9530 (coated cermet) Material: Cemented carbide Hole: with cylindrical hole + one-sided countersink (70°–90°) Chipbreaker: W10 Application: Turning FAQ What materials is this insert best suited for? The TPGH080202L-W10 in GT9530 is formulated for machining steel, offering a balance between surface finish and tool life in stable finishing conditions. Which toolholders are compatible with this insert? Compatibility depends on holder form, clearance, tolerance class, fastening method, size and thickness; the ISO-standard triangular form of the TPGH080202L-W10 fits standard triangular turning holders designed for size 08 inserts. How does the 0.2 mm corner radius affect surface finish? A 0.2 mm corner radius smooths the cutting action and reduces the risk of edge chipping during finishing passes, supporting improved surface quality and dimensional stability. Is the GT9530 grade suitable for heavy roughing? The GT9530 coated cermet is optimised for finishing to light universal turning rather than heavy roughing; for high-feed or heavy interrupted cuts, a tougher grade is preferable. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGH 080202 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of precise finishing performance, ISO compatibility and a low-force cutting geometry for reliable turning operations; order the insert through Metav Werkzeuge or consult our specialists for application-specific recommendations. TPGH 080202 NS9530 indexable turning insert — Tungaloy, 60° geometry, W10 chipbreaker TPGH080202L-W10 NS9530 Tungaloy insert designed for finishing turns on steel components, supplied as an ISO-standard triangular, hole-mounted turning insert. ISO TPGH triangular insert size 08 NS9530 cermet for fine finishing W10 chipbreaker for continuous cuts 11° clearance, 60° main geometry High-precision finishing with low cutting forces The NS9530 cermet grade is optimised for finishing steel where a sharp cutting edge and low cutting forces are priorities. This uncoated cermet delivers a high surface finish on continuous cuts and small depths of cut, reducing the need for downstream polishing. The insert geometry gives stable contact and predictable wear progression, which supports consistent component tolerances and repeatable part quality. Clear guidance on system compatibility and secure clamping Manufactured to ISO form and dimensions, the insert fits standard holders when the form, clearance, tolerance class, fastening method, size and thickness match. The TPGH080202L-W10 uses a cylindrical hole with a single-sided countersink (70°–90°), so correct clamping with the matching screw and clamp set is essential for repeatable positioning. Using the appropriate holder and a verified clamping kit minimises runout and improves tool life. Productivity and predictable process behaviour With its W10 chipbreaker and cermet cutting material, the insert enables high surface quality while maintaining productive machining cycles. Lower cutting forces reduce spindle load and can allow higher feed rates within the finishing window, improving throughput without sacrificing finish. The combination of geometry and grade is particularly economical for series production of turned parts where consistent surface quality is required. Practical selection and application tips for turning Choose this insert for external and internal finishing operations on unalloyed and alloyed steel, favouring continuous cuts and small depths of cut. The 11° clearance angle and 60° main geometry suit fine cuts; avoid heavy interrupted cuts to prevent chipping of the sharp cermet edge. For best results, pair the insert with a rigid holder, correct screw/clamp components and a stable setup to exploit the grade’s surface-quality advantages. Contact Metav Werkzeuge for tailored application advice and to reserve the Tungaloy TPGH 080202 NS9530 insert (SKU TUN6997996) for upcoming turning operations Technical data Article number: 6997996-Tungaloy Manufacturer SKU: TUN6997996 Manufacturer item number: 6997996 Model series: ISO-Drehwendeschneidplatten Facts Geometry angle: 60° Clearance angle: 11° Corner radius: 0.2 mm Thickness: 2.38 mm Special features ISO-standard triangular insert (size 08) Uncoated cermet grade NS9530 W10 chipbreaker; hole: cylindrical + single-sided countersink (70°–90°) Application: Turning; suited to continuous finishing cuts FAQ What materials is this insert intended for? The Tungaloy TPGH 080202 NS9530 insert is specified as a finishing grade for steel and performs best on continuous turning operations for improved surface quality. How is the insert clamped and mounted? The insert features a cylindrical hole with a single-sided countersink (70°–90°) and is mounted with the corresponding screw, clamp and holder; follow the ISO holder specification to ensure correct seating. Can this grade be used for roughing operations? The NS9530 uncoated cermet is optimised for finishing; the TPGH080202L-W10 is not recommended for heavy roughing or highly interrupted cuts due to its sharp cutting edge. Which chipbreaker should be selected for fine finishing? The supplied W10 chipbreaker on this insert is intended for continuous cuts and fine finishing, offering controlled chip formation and improved surface finish. Is there a specific holder geometry required for compatibility? Compatibility depends on the holder’s form, clearance, tolerance class, fastening and size; the insert conforms to ISO dimensions, so use an ISO-compatible holder matching the insert thickness and form. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGH 080204 GT9530 Wendeplatten - Tungaloy
Take advantage of the combination of coated cermet wear resistance, precise 60° cutting geometry, and reliable ISO compatibility for consistent finishing results in turning operations; order the TPGH080204 GT9530 directly via Metav Werkzeuge or ask our consultants for application support. TPGH 080204 GT9530 – Tungaloy indexable turning insert, coated cermet, 60° TPGH080204 GT9530 is a triangular, ISO‑compliant indexable insert for turning, designed for fine finishing and light universal machining where surface quality and extended tool life under stable conditions are required. Triangle insert TPGH080204 GT9530 Coated cermet for fine finishing 60° cutting angle, 0.4 mm corner radius Cylindrical hole with single-sided countersink Optimised performance for finishing and light universal turning This indexable cutting insert delivers predictable performance in turning thanks to its coated cermet grade and rigid geometry. The Cermet coating balances wear resistance with a polished cutting edge, which improves surface finish while reducing the need for rework. For applications requiring consistent dimensional accuracy and a fine part appearance, the combination of a 60° cutting angle and a 0.4 mm corner radius supports stable chip formation and controlled cutting forces, resulting in reduced vibration and fewer surface defects. Compatibility and secure clamping for predictable production Mounted inserts depend on exact fit and tolerance; the ISO designation and form of this insert ensure compatibility with standard holders that match the insert shape, thickness and fastening method. The triangular form and the specified hole style — a cylindrical hole with a single‑sided countersink (70°–90°) — allow secure clamping in the appropriate external holder or boring bar, which increases process reliability and repeatability during batch production. Choosing the correct holder and tightening torque prevents slippage and preserves tool life. Material suitability and operational benefits The GT9530 grade was developed as a wear‑resistant coated cermet for finishing to light universal machining of steel, offering longer life under stable machining conditions. The insert’s carbide backing provides the necessary rigidity for interrupting cutting loads, while the cermet coating enhances thermal stability at the cutting edge. As a result, the insert lowers overall tooling costs by extending intervals between indexings and enabling improved first‑pass quality — a clear rational advantage in precision turning workflows. Selecting the right insert and process tips When specifying this ISO insert for turning, pick a single‑sided chipbreaker and match feed and speed to the recommended range for cermets: moderate cutting speeds with stable setup typically yield the best compromise between surface finish and tool life. For roughing‑to‑finishing transitions, the geometry and grade support a move to lighter cuts for superior part appearance without tool change. For further guidance on holder match and cutting data, consult technical datasheets or request application advice to secure optimal results. For tailored compatibility checks, batch supply or to request the TUN6997890 specification sheet, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 for expert consultancy and ordering assistance Technical data Manufacturer article number: 6997890 SKU: 6997890-Tungaloy Model series: ISO-Drehwendeschneidplatten ISO designation: TPGH080204 Type: indexable turning insert Facts Thickness: 2.38 mm Corner radius: 0.4 mm Cutting angle: 60° Relief angle: 11° Size: 08 Hole: with hole Special features Grade: GT9530 coated cermet Substrate: cemented carbide Chipbreaker: one-sided Hole style: cylindrical hole + single-sided countersink (70°–90°) Shape: triangular Application: Turning FAQ What materials is this insert suited for? This insert is designed for machining steel and is supplied in the GT9530 coated cermet grade to provide wear resistance and improved surface finish for finishing to light universal operations. Which holders are compatible with this ISO insert? Compatibility depends on holder form, relief angle, tolerance class, fastening method, size and thickness; the insert’s ISO designation TPGH080204 helps to select a matching external holder or boring bar. How does the 0.4 mm corner radius affect part quality? A 0.4 mm corner radius produces a stronger cutting edge and smoother workpiece surfaces at finishing feeds, while reducing the risk of edge chipping under stable conditions. Is this insert suitable for interrupted cuts or unstable setups? The cemented carbide substrate offers rigidity, but the GT9530 cermet coating is optimised for stable conditions; for heavily interrupted cuts or unstable setups, evaluate alternative grades with higher toughness. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGH 080204 NS9530 Wendeplatten - Tungaloy
Take advantage of the combination of precise finishing performance, ISO compatibility and easy holder integration to maintain a smooth turning process; order the insert via Metav Werkzeuge or consult our specialists for selection and delivery. TPGH 080204 NS9530 turning insert for Turning — Tungaloy TPGH 080204 NS9530 is an ISO-format turning insert designed for finishing operations on steel, combining a sharp edge geometry with ISO compatibility for secure clamping and consistent surface quality Triangle insert, size 08, 60° included angle Uncoated cermet finishing grade NS9530 Sharp edge for low cutting forces and fine finish Central hole with cylindrical seat and countersink Dependable finishing with a cermet cutting edge The insert is made from an uncoated cermet material formulated as the finishing grade NS9530, which focuses on delivering a sharp cutting edge and low cutting forces. This composition reduces chatter and improves surface integrity during light cuts, making it well suited for applications where a high surface finish is required. For customers new to cermets: cermet combines ceramic hardness with metallic toughness, offering a balance of wear resistance and edge stability that benefits finishing passes in steel. ISO geometry that simplifies holder selection and set-up Produced as an ISO turning insert, the item follows standard dimensions so compatibility with clamping systems is governed by form, relief angle, tolerance class, fastening and thickness. The insert has an 11° relief angle, a 2.38 mm thickness and a 0.4 mm corner radius, which together determine the contact geometry with the toolholder and the resulting cutting forces. Specifying these values when selecting a matching outside holder or boring bar ensures repeatable positioning and reliable clamping, shortening set-up time and reducing trial cuts. Predictable machining for continuous and fine finishing cuts The single-sided chipbreaker and the uncoated cermet grade are optimised for continuous cuts and small depths of cut, producing consistent chip form and minimizing rework. That predictability translates into predictable cycle times and lower scrap rates in finishing operations. Where dimensional stability and surface quality are priorities, the insert supports a controlled process that favours fewer follow-on operations and steadier productivity on production runs. Application scope and system components explained The insert is intended for external and internal turning on steel in finishing-mode applications. It is supplied as part of an ISO-system consisting of the insert, a compatible external holder or boring bar, a mounting pad/clamping set and replacement screws; the insert’s with hole and cylindrical seat plus single-sided countersink (70°–90°) provides secure mechanical location for repeated indexing. For workshops seeking a simple upgrade path, matching the plate geometry and thickness to the existing tooling system delivers a fast route to improved surface quality without major tooling changes. For application advice or to secure Tungaloy finishing inserts, contact Metav Werkzeuge by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — our specialists will advise on suitability, holder selection and availability. Technical data Manufacturer article number: 6997997 SKU: 6997997-Tungaloy Manufacturer SKU: TUN6997997 Manufacturer: Tungaloy Series: ISO turning inserts Material: carbide Facts Size: 08 Thickness: 2.38 mm Relief angle: 11° Corner radius: 0.4 mm Included angle: 60° Mounting: with hole Special features Uncoated cermet grade NS9530 Finishing grade for steel with sharp cutting edge Single-sided chipbreaker Triangle plate form With hole: cylindrical seat + one-sided countersink (70°–90°) Compatible with ISO holders by form, relief angle, tolerance, fastening, size and thickness System components: external holder/boring bar, pad/clamping set and replacement screws FAQ Which materials is this insert suitable for? The TPGH 080204 NS9530 turning insert from Tungaloy is formulated as a finishing grade for steel and performs best in light finishing passes on carbon and alloy steels. Can the insert be used for internal turning operations? Yes; the geometry and central mounting hole make this insert suitable for both external and internal turning when paired with the appropriate boring bar or internal holder. How is the insert fastened in the holder? The insert features a central cylindrical hole with a one-sided countersink (70°–90°) and is secured using the matching pad/clamping set and replacement screws as part of the ISO system. What does NS9530 indicate? NS9530 designates the uncoated cermet grade used for this insert, optimised for finishing with a sharp edge and low cutting forces to produce superior surface quality. What kind of cutting conditions is the chipbreaker designed for? The single-sided chipbreaker is intended for continuous cutting with small depths of cut, promoting controlled chip formation and consistent surface results. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
TPGH 090204 GT9530 Wendeplatten - Tungaloy
Product data are inconsistent: the material is specified as cemented carbide while the cutting-grade is described as a coated cermet. Please verify the source data to ensure accuracy and consistency, as discrepancies like these can lead to confusion or potential errors in application, selection, or performance evaluation. It is crucial to confirm whether the material classification aligns with the intended use and whether the cutting-grade description accurately reflects the product's properties. Double-checking the original documentation or consulting with the relevant technical team might help clarify these inconsistencies and provide the necessary corrections to maintain data integrity.
TPGH 090204 NS9530 W10 Wendeplatten - Tungaloy
Benefit from the combination of a sharp, uncoated cermet cutting edge, ISO compatibility and a finely tuned W10 chipbreaker for reliable finishing on steel; order the insert directly via Metav Werkzeuge or consult the technical team for machining guidance. TPGH 090204 NS9530 Tungaloy — ISO turning indexable insert with W10 chipbreaker and 11° clearance A TPGH 090204 NS9530 Tungaloy ISO-standard triangular insert designed for precision finishing in turning applications on steel. Uncoated cermet grade NS9530 for fine finishing Sharp cutting edge with low cutting forces ISO-standard triangular 09 size, 11° clearance 0.4 mm corner radius and W10 chipbreaker Precision finishing performance for turning operations The insert is engineered as a finishing grade to produce superior surface quality in continuous cutting on steel. Its uncoated cermet composition delivers a sharp, wear-resistant cutting edge that maintains profile integrity during extended runs, while the combination of low cutting forces and a tuned chipbreaker reduces vibration and heat generation. These properties result in consistent dimensional accuracy and reduced rework, making the insert a pragmatic choice where surface finish and repeatability are priorities. The technical specification supports stable machining at small depths of cut and modest feed rates typical for finishing passes. Reliable compatibility and geometrical clarity Supplied in an ISO-standard triangular format (09 size) with an included angle of 60°, the insert fits a wide range of external holders and boring bars when the holder’s form, clearance angle (11°), tolerance class, mounting arrangement, size and thickness are matched. The insert thickness of 2.38 mm, the 0.4 mm corner radius and the presence of a cylindrical hole with one-sided countersink (70°–90°) are decisive for seating and clamping stability. These well-defined geometric parameters simplify selector checks and reduce the time needed to confirm holder compatibility, enabling a faster set-up and more predictable process control. Process advantages and application guidance The NS9530 grade and W10 chipbreaker are tailored for continuous finishing cuts on steel, offering a balance between edge sharpness and wear resistance. The insert’s design reduces cutting forces, which helps to protect both the tool and the workpiece from chatter and thermal distortion. For best results, choose a matching holder and feed strategy consistent with finishing practice: shallow depths of cut, stable fixture, and reduced feed to exploit the cermet’s edge quality. Where interrupted cuts or heavy build-up occur, select a different chipbreaker or a more robust grade to maintain process security. Integration into the tooling system and practical notes As part of a standard ISO insert system, each component functions in concert: the indexable insert, a matched external holder or boring bar, and the appropriate clamping set and replacement screws form the complete tooling solution. The insert’s sharp cutting geometry and uncoated surface favour applications where surface appearance and tight tolerances are required. When ordering or specifying, reference the model series and article codes to ensure the correct variant is supplied; for complex applications, Metav Werkzeuge’s technical advisors can provide parameter recommendations and help with holder selection to optimise cycle time and component quality. The Tungaloy finishing insert is particularly effective where consistent surface integrity matters. For precise finishing with Tungaloy cermet inserts, contact Metav Werkzeuge for application advice and availability via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 6997998 Manufacturer SKU: TUN6997998 Label: TPGH090204L-W10 NS9530 Tungaloy-Wendeplatte Core dimensions Size: 09 Thickness: 2.38 mm Included angle: 60° Clearance angle: 11° Corner radius: 0.4 mm Features & applications Uncoated cermet grade NS9530 W10 chipbreaker Triangular shape With hole; cylindrical hole + one-sided countersink (70°–90°) For turning; finishing on steel Model series: ISO turning indexable inserts FAQ Is this insert suitable for finishing operations on steel? Yes. The NS9530 uncoated cermet grade of the TPGH 090204 NS9530 Tungaloy insert is designed as a finishing grade for steel, offering a sharp edge and low cutting forces for high surface quality. Which holder characteristics determine compatibility with the insert? Compatibility is determined by the holder’s form, clearance angle, tolerance class, mounting, size and thickness; the insert’s 11° clearance and 2.38 mm thickness are key reference values. What does the W10 chipbreaker mean for chip control? The W10 chipbreaker is tuned to provide controlled chip formation during continuous finishing cuts, reducing the risk of long, stringy chips and supporting stable machining performance. Can the insert be used for internal and external turning? Yes. The ISO triangular format and the insert’s geometry allow use in both external holders and appropriate boring bars for internal turning, provided the holder matches the insert’s dimensions and clamping style. How should the 0.4 mm corner radius influence feed selection? A 0.4 mm corner radius is small and suited to finishing feeds; selecting a moderate feed rate helps achieve the desired surface finish while avoiding excessive edge loading. Manufacturer/Responsible: Tungaloy-NTK Germany GmbH, Katzbergstraße 3a, 40764 Langenfeld - Protected trademarks and product names are the property of their respective owners. Brand names and protected trademarks are mentioned solely for explanatory purposes. There is no affiliation between our company and the mentioned brands. The item offered is an original, brand-new product from the manufacturer.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com