Secure and precise workholding for metalworking productivity
Workholding devices such as workpiece clamps and chuck systems provide absolute positional stability and vibration damping during milling, turning, drilling and grinding, ensuring parts remain free of play under high CNC cutting and feed forces. By transferring clamping loads into the machine table or spindle without deforming the component, a well engineered workholding solution improves machining accuracy, surface finish and process reliability while reducing set-up times. Modular systems from machine vices and chucks to zero-point systems and specialised fixtures enable fast changeovers and support both serial and single-part production, delivering consistent clamping force, repeatability and enhanced throughput.
21.5mm Rubber Flex Collet Holder For VTA7 Threading Attachment, Ø4–Ø7mm Compatible - Vertex
Take advantage of the combination of flexible rubber clamping, precise centring and compact dimensions for reliable thread cutting operations; order the collets directly via Metav Werkzeuge or consult the team for selection advice. Rubber-Flex Collets FC for VTA7 Thread Cutting Attachment (Ø21.5 mm) The Rubber-Flex Collets FC for VTA7 are flexible clamping inserts designed to secure small-diameter tool shanks in a thread cutting attachment for workshop and light industrial use. Flexible rubber clamping element for secure hold Designed for VTA7 thread cutting attachment Nominal diameter Ø21.5 mm for compact fixtures Suitable for shanks Ø4–Ø7 mm with fine centring Reliable clamping for consistent thread cutting The set of collets provides elastic clamping that adapts to minor shaft tolerances and reduces runout during threading. Built for use with the VTA7 thread cutting attachment, the inserts convert radial compliance into a stable grip, lowering the risk of chatter and premature tool wear. This behaviour benefits repetitive operations where consistent thread geometry is required and supports steady cycle times on manual and semi-automatic equipment. Measured compatibility and performance benefits With a nominal external diameter of Ø21.5 mm and a length of 13 mm, the collets present a compact interface that suits confined toolholders and short overhangs. The internal clamping range of Ø4–Ø7 mm accommodates common small shank sizes used in thread cutting. Caution: the elastic design compensates for minor dimensional variation but is not a substitute for properly ground tool shanks. The result is improved centring and reduced axial and radial deviation, which translates into more precise thread profiles and fewer scrap parts. Durable operation and workflow advantages Engineered for repeatable use in workshop environments, the Rubber-Flex inserts combine simple replacement with operational robustness. Their rubber-based clamping surface cushions the tool shank, decreasing point loads and minimising marring on delicate shafts. Stocking these collets alongside conventional rigid chucks can improve setup flexibility and shorten machine downtime. Metav’s logistics and quality control in Emmerich ensure dependable availability for production runs and maintenance cycles. Choose the Vertex FC-20 Rubber-Flex collets for improved thread-cutting stability and ask Metav Werkzeuge for assistance with compatibility or ordering to ensure an optimal match for the tooling setup Technical Data Article number: FC-20 GTIN: 4061905094866 Manufacturer: Vertex Core dimensions External diameter: Ø21.5 mm Length: 13 mm Internal clamping range: Ø4–Ø7 mm Compatibility & features Designed for thread cutting attachment VTA7 Flexible rubber clamping inserts Category: clamping collet series FC FAQ How do the Rubber-Flex collets improve thread quality? The Rubber-Flex collets reduce runout through elastic clamping, improving the centring of the tool shank and resulting in more consistent thread profiles when used with the VTA7 attachment. Which shank diameters are supported by these collets? The collets accept shanks in the Ø4–Ø7 mm range; the FC-20 design adapts to small tolerances within that span to maintain grip and precision. Are these collets compatible with other thread cutting systems? They are specifically designed for the VTA7 thread cutting attachment; alternative systems may require different collet geometries or adaptors to ensure proper seating and clamping. What maintenance is required to keep performance stable? Periodic inspection for wear of the rubber surface and cleaning of the collet bore preserves clamping performance; replacement is advised when deformation or hardening is observed. Is the FC-20 suitable for high-speed threading operations? The elastic clamping improves stability for typical threading speeds used with VTA7; for high-speed or heavy-duty machining, selection should be validated against the specific tooling and spindle conditions. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
210x730mm Precision Cross Table 405x345mm Base, 16mm T‑Slot, 35 Kg Capacity - Vertex
Take advantage of a compact solution that combines high repeatability, secure fixturing and a generous work surface — ideal for accurate set-ups and small-series machining. The combination of accuracy 0.02 mm, a 210 x 730 mm table and a 35 kg load capacity supports reliable production throughput. Order the VCT-830 directly via Metav Werkzeuge or ask our consultants if needed. VCT-830 Precision cross table by Vertex — 210 x 730 mm, 35 kg load The VCT-830 is a precision cross table designed for accurate positional work and versatile fixturing in machine shops and inspection benches. 210 x 730 mm work surface High positioning accuracy 0.02 mm Max load 35 kg T-slot 16 mm for secure fixturing Consistent, high-precision positioning for repeatable results A low-backlash lead screw and rigid guideways deliver precision that reduces rework and shortens inspection cycles. The combination of a wide 210 x 730 mm table and the stated accuracy 0.02 mm means repeatable positioning for milling, drilling and measurement tasks where tolerances matter. This level of control translates into predictable part quality and fewer adjustment steps during setup, supporting efficiency on the shop floor. Built for stable, versatile fixturing across applications The work surface includes T-slot 16 mm provision for secure clamping and a footprint optimised for bench- or machine-mounting. With a 35 kg maximum load and a compact base, the table is suitable for precision tooling, optical inspection and small component machining. Robust construction minimises vibration transfer and keeps axes aligned under load, which preserves dimensional integrity when performing through-feed or short-length machining operations. Serviceable design that supports workshop workflows The unit’s footprint and mounting pattern (405 x 345 mm base) aid integration into existing setups without extensive modification. Accessible adjustment points and standard fixturing interfaces reduce downtime during tool changes and calibration. Supplied specifications and measurable characteristics enable planning for fixtures and process control, helping maintain throughput while ensuring compliance with quality checks. Contact Metav Werkzeuge to secure Vertex precision positioning with the VCT-830 and request tailored advice from our Emmerich specialists Technical data SKU: VCT-830 GTIN: 4061905089022 ECLASS: 21041714 Facts Table surface: 210 x 730 mm Footprint: 405 x 345 mm Accuracy: 0.02 mm Max load: 35 kg Weight: 100 kg T-slot: 16 mm Special features Manufacturer: Vertex Precision cross table for positioning and machining Compatible with T-slot clamping accessories FAQ What level of positional accuracy can be expected from this cross table? The VCT-830 offers a stated positional accuracy of 0.02 mm, enabling precise set-ups for measuring, milling and drilling tasks where tight tolerances are required. Can the table support typical small-part machining loads? Yes, the precision cross table supports a maximum load of 35 kg, which is suitable for many small-part machining and inspection applications when mounted correctly. Which table size is available for fixture planning? The work surface measures 210 x 730 mm, providing ample room for fixturing and multiple clamping points for small- to medium-sized components. How is workpiece clamping achieved on the table? Clamping is achieved via a T-slot: 16 mm profile integrated into the table, allowing standard T-slot fixtures and clamps to be used for secure fixing. Is the VCT-830 suitable for integration into an inspection bench or milling machine? The VCT-830 is intended as a precision positioning device and can be integrated into inspection benches or machine tables provided the mounting footprint and load limits are observed. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
213mm Vertical Clamp With Safety Lock, Zinc Coated, 2,000N Thrust / 2,500N Hold - Kukamet
Take advantage of a robust, galvanised construction combined with an integrated safety lock and a compact, lightweight design to secure fixtures reliably in confined setups; order the 213 vertical clamp directly via Metav Werkzeuge or contact our consultants for application advice. 213 vertical clamp — Vertical toggle clamp with safety lock and galvanised finish The 213 vertical clamp is a vertical toggle clamp designed for securing workpieces on jigs and fixtures, fitted with an angle base for fixed mounting in industrial and workshop applications. Galvanised finish for corrosion resistance Built-in safety lock for secure clamping 2,500 N maximum holding force Secure clamping for confined workstations The 213 vertical clamp delivers dependable holding performance where space is limited. With a maximum holding force of 2,500 N, the clamp provides stable retention for assembly and welding fixtures, reducing the need for repeated repositioning. The galvanised construction offers corrosion resistance, which extends service life in humid or workshop environments and keeps maintenance needs low. The compact form and low mass (0.47 kg) ease handling during fixture set-up and reduce fixture load without compromising stability. Fast, durable mounting and repeatable positioning Fitted with an angle base, the clamp mounts quickly to plates or brackets, enabling straightforward integration into existing jigs. The pressure spindle is sized M8x50, allowing secure contact adjustment and predictable clamping stroke. These tangible, machine‑oriented features translate into faster fixture assembly and consistent part repeatability, meaning shorter cycle times and fewer rejects on repetitive operations. The galvanised finish and robust mechanism support regular industrial use and long-term reliability. Safe operation and clear functional advantages Operation is enhanced by the safety lock, which prevents accidental release during machining or handling and thereby protects tooling and workpieces. The vertical toggle mechanism provides direct downward force with minimal lever travel, simplifying clamp actuation and improving operator ergonomics. Taken together, the design decisions reduce process interruptions and offer measurable gains in throughput and workplace safety, making this clamp suitable for production workbenches and dedicated fixture systems. For reliable vertical clamping with proven holding force, contact Metav Werkzeuge for tailored advice and secure supply from Emmerich: info@metav-werkzeuge.com · +49 2822 7131930 Technical Data SKU: 213-3-L GTIN: 8680731502015 Manufacturer: Kukamet Core data Weight: 0.47 kg Maximum holding force: 2,500 N Maximum pressing force: 2,000 N Pressure spindle: M8x50 ECLASS: 21041717 ETIM: EC011973 Special features Material: galvanised Mounting: angle base Integrated safety lock Category: vertical toggle clamp Story trigger: lever clamp FAQ What applications suit this clamp best? The 213 vertical clamp is appropriate for jigs, assembly fixtures and welding tables where a vertical clamping action and strong retention (2,500 N) are required. How is the clamp mounted to a fixture? Mounting is via the angle base; the 213 installs directly to plates or brackets and is compatible with an M8x50 pressure spindle for contact setup. Does the clamp include a safety mechanism? Yes, the 213 vertical clamp features an integrated safety lock to prevent unintended release during machining or handling. What material is the clamp made from and how does that affect use? The clamp is made from galvanised steel, which provides corrosion resistance and reduces maintenance in workshop environments. Is the holding force sufficient for heavy-duty tasks? With a maximum holding force of 2,500 N, the 213 is suitable for many production and fixture tasks requiring reliable retention. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
215mm Extension Lever Metal For Clamping Levers, 20.5mm Wide x 10mm Thick - Kukamet
Taking advantage of the metal construction and the 215 mm length provides extended reach and increased leverage for lever-clamping tasks; the lightweight design at 0.307 kg keeps handling straightforward and reduces operator fatigue. Order the extension lever directly via Metav Werkzeuge or ask our consultants for compatibility advice. Extension lever 220 — Metal extension arm, 215 mm (Kukamet) A 220 extension lever engineered to extend reach and improve leverage for lever clamps in workshop and industrial clamping applications Robust metal construction 215 mm length for extra reach Lightweight at 0.307 kg Compatible with lever clamps Greater leverage with a compact profile The compact extension lever delivers measurable mechanical advantage where additional reach is required. By extending the lever arm to 215 mm, the component increases torque transmission from existing clamp handles without altering the clamp body, enabling firmer engagement with the same manual input. This characteristic reduces operator effort and helps maintain consistent clamping force across repetitive cycles, supporting reliable production throughput and fewer rework steps. The design is particularly beneficial in confined set-ups where space for the clamp handle is limited but more reach is necessary. Built for workshop reliability and simple maintenance Constructed from metal, the lever is designed for routine industrial use and occasional impact. The solid material choice supports long-term wear resistance and contributes to predictable behaviour under load. At 0.307 kg, the component remains easy to handle during assembly and adjustment while still offering the mass needed for stable operation. The robust construction minimises the need for frequent replacement, reducing downtime and maintenance interruptions in a production environment. Easy integration with existing clamping systems The extension arm is intended for straightforward retrofitting to lever-type clamps and spanners. Clear mechanical interfaces allow for rapid installation, meaning line-side changeovers or jig adjustments can be completed with minimal tooling. The part is identified as SKU 220-6-06-C1, which simplifies ordering and parts management. Compatibility with standard lever clamp assemblies ensures that integration does not require bespoke adapters, keeping installation time and associated costs low. Practical choice for daily workshop use Precision in everyday clamping starts with appropriate tooling: the lever extension supports repeatable set-ups and safer handling by increasing clearance between the operator and the workpiece. Its construction and dimensions make it suitable for a range of general workshop and light industrial applications where enhanced reach and consistent clamp actuation are required. For buyers seeking dependable components from an established supply chain, the product benefits from Metav’s European distribution, which acts as a quality filter and ensures accessible stock and reliable fulfilment. For enhanced reach in lever-clamping applications, request the Kukamet extension lever (220) from Metav Werkzeuge — contact our Emmerich team at info@metav-werkzeuge.com or call +49 2822 7131930 for availability and expert advice. Technical data SKU: 220-6-06-C1 GTIN: 4061905076831 ECLASS: 21170613 Facts Height: 215 mm Width: 20.5 mm Thickness: 10 mm Weight: 0.307 kg Materials & features Material: Metal Category: Spanner Manufacturer: Kukamet Asset: 220-2-06-main.jpg FAQ How does the extension lever 220 increase clamping leverage? The extension lever 220 increases lever arm length to 215 mm, raising torque for existing lever clamps and allowing firmer clamp engagement with the same manual input. Is the extension arm suitable for heavy industrial use? The part is made from metal and designed for workshop and light industrial environments; it offers robust behaviour under routine loads but is not specified as a heavy-duty machine element. Which SKU should be ordered to replace or add this accessory? Order SKU 220-6-06-C1 for the Kukamet extension lever 220 to ensure correct fit and traceability. Can the lever be fitted to different clamp brands? The extension is compatible with standard lever clamps and spanners; its design allows retrofit to common clamp assemblies without bespoke adapters. What are the exact dimensions to check for fitment? Key dimensions are height 215 mm, width 20.5 mm and thickness 10 mm; use these values to verify mechanical clearance and mounting geometry. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
215mm Extension Sleeve MK3×MK3 Hardened Ground According To DIN 2187 - TECWERK
Benefit from the combination of DIN 2187 accuracy, fully hardened and ground surfaces, and a 215 mm overall length for reliable extended-reach machining. Order the extension sleeve directly via Metav Werkzeuge or ask our consultants for technical advice. Extension sleeve DIN 2187 MK3×MK3 – TECWERK The Extension sleeve DIN 2187 MK3×MK3 is an industrial extension sleeve that extends Morse taper tooling to reach deeper bores while maintaining precision and interchangeability for workshop and toolroom applications DIN 2187 accuracy version Fully hardened and ground inside and out For tools with Morse taper MK3 Total length 215 mm for extended reach Engineered for consistent machining accuracy Manufactured to the DIN 2187 specification, this extension sleeve is designed as an accuracy version to ensure repeatable positioning and stable results in precision operations. The internal and external surfaces are hardened and ground, which reduces surface distortion and helps preserve the intended geometry under load. As a consequence, tool runout is minimised and concentricity is maintained, delivering reliable component tolerances in milling, drilling and reaming tasks where repeatability is essential. Extended reach with retained rigidity With a total length of 215 mm and a usable length of 112 mm, the sleeve provides additional reach for machining tasks that would otherwise require inconvenient setups or special tooling. The larger outer diameter (D 36 mm) contributes to torsional stiffness, so extended-reach applications do not come at the expense of stability. This design reduces the need for multiple tool changes and simplifies clamping strategies, improving workflow efficiency on production runs and one-off engineering tasks alike. Built to withstand regular workshop use The sleeve is supplied in a fully hardened and ground finish both internally and externally, which enhances surface wear resistance and reduces the frequency of replacement. The robust treatment of contact faces ensures long service life in continuous-shop environments, while precision grinding provides smooth mating with mating tapers. The Extension sleeve DIN 2187 MK3×MK3 by TECWERK is therefore suited to workshops that demand dependable tooling performance with low maintenance overhead. Easy integration and broad compatibility Standardised to DIN 2187 and fitted with MK3 internal and external tapers, this sleeve is compatible with a wide range of Morse taper tooling and spindles, enabling straightforward interchangeability across machines and fixtures. The adherence to the norm simplifies procurement and setup, allowing toolrooms to maintain consistent inventories and reduce adapter complexity. That interoperability supports faster changeovers, fewer assembly errors and a more predictable production flow. For detailed application advice or to arrange supply from Metav Werkzeuge’s Emmerich warehouse, contact Metav Werkzeuge for expert guidance and dependable delivery Technical Data Article number: 2000832340NW Standard: DIN 2187 Product: Extension sleeve Manufacturer: TECWERK Packaging unit: 1 Facts Total length L2: 215 mm Usable length L1: 112 mm Outer diameter D: 36 mm Internal taper: MK3 External taper: MK3 Special features Accuracy version to DIN 2187 Fully hardened and ground inside and out Designed for tools with Morse taper FAQ What tolerance and precision can be expected from this sleeve? The extension sleeve complies with the DIN 2187 accuracy version; the TECWERK extension sleeve is ground and hardened to preserve concentricity and provide consistent repeatability. Is the sleeve compatible with MK3 tooling and spindles? Yes, the product features an internal and external MK3 taper and is intended for use with Morse taper tooling, ensuring direct compatibility. What are the main dimensions of the sleeve? The TECWERK extension sleeve has a total length of 215 mm (L2), a usable length of 112 mm (L1) and an outer diameter of 36 mm. Can the sleeve be used for deep-hole drilling or long-reach operations? The 215 mm overall length is specifically provided to extend tool reach while retaining rigidity, so the sleeve is suitable for many deep or hard-to-access machining tasks. How is the sleeve finished and what does that mean for service life? The extension sleeve is fully hardened and ground inside and out; this surface treatment improves wear resistance and helps maintain precise taper contact over prolonged use. Manufacturer / Responsible: NORDWEST Handel AG, Robert‑Schuman‑Straße 17, 44263 Dortmund
215mm Extension Sleeve MK4 to MK2 Hardened Ground, DIN 2187 - TECWERK
Combining DIN 2187 precision with a hardened and ground finish and a Morse taper transition from MK4 to MK2, this extension sleeve provides stable tool seating and consistent run-out control for demanding machining operations; secure supplies and technical advice are available through Metav Werkzeuge. Extension Sleeve DIN 2187 MK4 x MK2, hardened & ground — TECWERK A Extension Sleeve DIN 2187 MK4 x MK2 (TECWERK) engineered to adapt larger spindles to MK2 tools while maintaining concentricity and reliable clamping in industrial machine shops. DIN 2187 compliance for tool holders Morse taper MK4 to MK2 adaptation Hardened and ground inside and out Precision dimensions D 30 mm, L 215 mm High-precision adaptation for consistent machining results The sleeve is designed to provide a secure Morse taper transition between MK4 and MK2 interfaces, ensuring reduced runout and stable tool seating during operation. Manufactured to DIN 2187 and executed in a precision accuracy version, the component is hardened and ground both internally and externally, which minimises deformation under load and preserves concentricity over repeated use. This translates into fewer rejects, longer tool life and predictable performance in milling, drilling and reaming applications where concentricity is critical. Robust construction that supports productive uptime A fully worked and finished sleeve delivers mechanical reliability: the hardened substrate resists wear, while the ground surfaces ensure a close fit with the mating tapers. The combination of surface treatment and accuracy grading reduces fretting and micromovement between spindle and tool, which supports repeatable setups and limits vibration. With a nominal diameter of D 30 mm and a total length of 215 mm, this component is suitable for operations requiring extended reach without compromising stability. Practical compatibility and quick integration into existing toolrooms The sleeve is intended for tools presented with a Morse taper, facilitating straightforward adaptation of MK2 shanks to MK4 spindles. Key dimensions such as L1 97.5 mm and overall length 215 mm allow planners to check clearance and engagement depth at a glance. Installation is simple: clean contact surfaces, press-fit the sleeve according to standard machine practice and verify seating; correct mounting secures the intended concentricity benefits. Regular inspection of the tapered faces and routine cleaning will maintain the performance advantages over long service intervals. For tailored advice on application and delivery from Metav Werkzeuge — including compatibility checks and supply from Emmerich — contact our technical team via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 2000832364NW Standard: DIN 2187 Type: Extension sleeve Brand: TECWERK Facts Total length L2: 215 mm Engagement length L1: 97.5 mm Diameter D: 30 mm Inner taper: MK2 Outer taper: MK4 Special features Hardened and ground inside and out Accuracy execution (precision version) For tools with Morse taper Designed per DIN 2187 FAQ What applications is this extension sleeve suitable for? The Extension Sleeve DIN 2187 MK4 x MK2 (TECWERK, SKU 2000832364NW) is suitable for adapting MK2 shank tools to MK4 spindles in machining tasks where concentricity and stiffness are required. How does the hardened and ground finish benefit workshop use? A hardened and ground finish on the sleeve ensures wear resistance and precise mating surfaces, which for the TECWERK extension sleeve reduces runout and extends the life of both the sleeve and the mounted tools. Are the dimensions compatible with standard Morse taper tooling? Yes; the component follows DIN 2187 and provides an MK4 outer taper to accept an MK2 inner taper, with key dimensions D 30 mm, L2 215 mm and L1 97.5 mm for easy verification against existing tooling. What maintenance is recommended to preserve accuracy? Keep the tapered faces free from debris and corrosion, inspect mating surfaces for nicks, and follow standard machine-shop mounting procedures; regular checks maintain the precision benefits of this TECWERK extension sleeve. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
217mm Horizontal Clamp With Massive Holding Arm And Safety Lock, 90° Angle - Kukamet
Benefit from robust clamping with a 217 mm reach, a 5,000 N holding force and a secure safety lock to maintain consistent workpiece position in production. Order the (Kukamet 113 horizontal toggle clamp) directly via (Metav Werkzeuge) or ask our consultants if needed. Kukamet 113 Horizontal Toggle Clamp — 217 mm arm, 5,000 N holding force Kukamet 113 horizontal toggle clamp designed for demanding workshop and light industrial clamping tasks where repeatable, safe fixation is essential. Massive holding arm for secure clamping Safety locking mechanism prevents opening 217 mm arm for wide reach Angle base for stable mounting Reliable holding capacity for consistent production The clamp offers a combination of high holding force and compact design that supports steady machining and assembly processes. With a 5,000 N holding force and a 4,500 N clamping force, the unit secures medium to heavy workpieces without frequent readjustment, reducing cycle time and rework. Its measured mass and geometry contribute to repeatable results on jigs and fixtures, making the device suitable for general workshop tasks and small-batch industrial production where stability and speed matter. Built for safety and long service life A massive holding arm and an integrated safety lock deliver both mechanical strength and operational confidence. The locking mechanism prevents unintentional release under vibration or sudden loads, which reduces scrap and improves operator safety. The component carries a black blued finish that offers basic corrosion resistance and a professional appearance while maintaining serviceability. The clamp strikes a balance between robustness and straightforward maintenance for everyday use. Flexible mounting and practical handling The right-angle angle base provides a stable mounting footprint and straightforward integration into fixtures, pallets or bench plates. The 217 mm arm extends reach without compromising leverage, enabling secure clamping of larger parts or assemblies. At a weight of 1.84 kg the unit remains easy to position during set-up yet substantial enough to resist deflection under load. Suitable for fabrication, welding jigs and assembly stations, the clamp supports efficient workflows and enhanced process control. For durable, safety-focused clamping opt for the Kukamet 113 and contact Metav Werkzeuge for ordering and installation advice — info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data Article number: B113-5-D-L-C3 SKU: B113-5-D-L-C3 ETIM: EC011973 eClass: 21041719 Facts Arm length: 217 mm Weight: 1.84 kg Clamping force (max): 4,500 N Holding force (max): 5,000 N Angle: 90° Special features Material / finish: black blued finish Mounting type: angle base Massive holding arm Safety locking mechanism Suitable for lever clamp applications FAQ What is the maximum holding force of this clamp? The Kukamet 113 horizontal toggle clamp provides a maximum holding force of 5,000 N, suitable for a range of workshop and light industrial tasks. Can the clamp be mounted on custom fixtures? Yes, the clamp’s angle base allows straightforward mounting on fixtures, pallets or bench plates for bespoke jigs and workholding solutions. What finish does the clamp have and how does it affect durability? The unit features a black blued finish, which provides basic corrosion resistance and a durable surface for everyday workshop environments. Is this clamp suitable for repetitive production use? The combination of massive holding arm, safety lock and robust forces makes this clamp well suited to repetitive clamping in assembly and machining operations. Which applications are best suited to this type of clamp? Typical uses include welding jigs, assembly stations and general fabrication where secure, repeatable holding and quick operation are required. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
218.5mm Vertical Clamp With Angle Base, Massive Holding Arm, 4.5kN Thrust, 5kN Hold - Kukamet
Combine robust clamping performance with a compact footprint: the 213 Vertical Clamp delivers a massive holding arm, up to 5,000 N static holding force and a 218.5 mm reach for secure fixtures. Order the clamp directly via Metav Werkzeuge or consult our specialists for application advice. 213 Vertical Clamp – Vertical lever clamp with 5,000 N holding force and 218.5 mm arm (Kukamet) The 213 Vertical Clamp is a vertical lever clamp designed for secure fixturing in workshop and light industrial applications, featuring a solid holding arm and a right‑angle mounting base for fixed installation Robust solid holding arm for heavy loads Up to 5,000 N static holding force 218.5 mm reach for deeper fixtures Right-angle base for fixed mounting Consistent, measurable clamping for repeatable processes The clamp provides clearly defined mechanical performance: a holding force of 5,000 N and a closing force of 4,500 N, values that translate directly into reliable workholding during machining and assembly. These figures indicate the permissible static and actuation loads, allowing planners to calculate fixture safety margins and cycle security. The solid holding arm reduces deformation under load, so clamping remains consistent across repetitive operations. Small footprint, flexible installation for workshop integration With a reach of 218.5 mm and a right‑angle mounting base, this clamp integrates into compact fixture layouts while keeping the working envelope accessible. The right‑angle base permits secure bolting to machine tables or fixture plates without additional adapters. At approximately 1.836 kg, the unit balances heft for stability with manageable handling during assembly of jigs and fixtures. Durable finish and simple lever action for low maintenance A black oxide finish provides surface protection and reduces glare in a workshop environment, while the lever‑type actuation offers rapid clamp/unclamp cycles for high throughput. The combination of a massive holding arm and solid mechanical construction reduces wear on moving parts, supporting longer service intervals and predictable maintenance planning. Where quick, repeatable clamping is required, the lever mechanism preserves cycle time without sacrificing grip. Designed for reliable workshop performance Engineered as a vertical acting clamp, the device suits general clamping tasks in metalworking and workshop contexts where repeatability and clear force ratings matter. The compact design and robust components support use in fixtures, assembly stations and prototyping benches, providing a pragmatic solution for production and repair environments that prioritise measurable results over guesswork. Select the Kukamet 213 Vertical Clamp for reliable, repeatable clamping — contact Metav Werkzeuge for application-specific advice or to arrange purchase via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: B213-5-D-C3 GTIN: 8680731508086 Manufacturer: Kukamet Core specifications Arm length: 218.5 mm Holding force: 5,000 N Closing force: 4,500 N Weight: 1.836 kg eClass: 21041717 ETIM: EC011973 Special features Mounting type: Right-angle base Finish: Black oxide Massive holding arm Lever clamp (vertical actuation) Category: Clamping devices FAQ What maximum holding force does the clamp provide? The 213 Vertical Clamp offers a maximum static holding force of 5,000 N and a closing (actuation) force of 4,500 N for predictable workholding. How is the clamp mounted? Mounting is via a right‑angle base enabling secure bolting to fixture plates and machine tables. What is the effective reach of the clamping arm? The clamping arm extends 218.5 mm, providing clearance for deeper or recessed workpieces. What is the unit weight and how does that affect fixture design? Weight is approximately 1.836 kg; the mass supports fixture stability while remaining manageable for assembly. What finish and construction features support durability? A black oxide finish and a solid, massive holding arm provide surface protection and reduced deformation under load. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
218.5mm Vertical Clamp With Angle Foot, Massive Holding Arm, 4.5kN Thrust 5kN Holding Force, Galvanised - Kukamet
Take advantage of a robust clamping solution with a massive holding arm, galvanised corrosion protection and a 5,000 N maximum holding force for secure fixture set-ups; order directly via Metav Werkzeuge or consult our specialists for application advice. 213 vertical clamp by Kukamet — massive holding arm, 5,000 N holding force The 213 vertical clamp is a compact vertical clamping device designed for workshop jigs and fixture tables, offering a long reach and reliable repeatability for small- to medium-scale production tasks. Massive holding arm for stable clamping 218.5 mm arm reach for deep applications Galvanised steel construction for corrosion resistance 5,000 N maximum holding force Secure clamping for repeatable production quality The clamp is engineered for consistent, repeatable holding: the 5,000 N maximum holding force and a separate 4,500 N pressing capacity ensure workpieces remain stable during machining and assembly. The heavy-duty arm provides mechanical advantage for lever-actuated locking, reducing the chance of part movement under cutting forces. For operators transitioning from manual setups, the device’s straightforward function reduces setup time and contributes to predictable cycle times on the shop floor. The combination of defined clamping forces and rigid construction supports quality control and reduces rework. Flexible installation and clear specifications for fixture design Mounting is via an angle foot, enabling secure attachment to t-slotted tables, plates or custom subplates; the 218.5 mm arm length extends reach into deeper jigs while keeping the overall footprint compact. The nominal mass of 1.836 kg balances robustness with ease of handling during fixture assembly. Numeric values such as arm reach and rated forces are provided to aid CAD layout and strength calculations during fixture design, allowing planners to position clamps with adequate spacing to avoid deformation or interference in multi-clamp assemblies. Durable finish and low-maintenance operation for workshop conditions A galvanised surface finish protects components from corrosion in industrial environments and minimises surface wear during repetitive use. The heavy holding arm is designed for mechanical resilience, reducing sensitivity to knocks and frequent actuation. Maintenance is primarily visual inspection and light lubrication at pivot points; this straightforward care routine keeps downtime low and supports long service life, making the clamp a practical choice for maintenance shops, toolrooms and small production lines. For reliable delivery from our Emmerich stock and application support for Kukamet clamping solutions — contact Metav Werkzeuge for tailored advice on integrating the robust 213 vertical clamp into existing fixture systems: phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: 213-5-D-C3 GTIN: 8680731502138 Brand: Kukamet Material finish: Galvanised Category: Clamping Facts Arm length: 218.5 mm Holding force max: 5,000 N Pressing force max: 4,500 N Weight: 1.836 kg SKU: 213-5-D-C3 Special features Mounting: Angle foot Massive holding arm Compact vertical clamp design Suitable for workshop and jig fixtures FAQ What clamping force can be expected from this clamp? The Kukamet 213 vertical clamp offers a maximum holding force of 5,000 N with a separate pressing capacity rated to 4,500 N for secure fixture retention. How is the clamp mounted to a fixture plate? Mounting is via the angle foot configuration, allowing the clamp to be bolted to t-slot tables, base plates or bespoke subplates for stable installation. Is the surface finish suitable for industrial environments? Yes, the galvanised finish on the 213 vertical clamp provides corrosion resistance suited to typical workshop and production environments. What is the reach of the clamping arm and how does that affect layout planning? The arm reach is 218.5 mm, which should be considered when spacing multiple clamps to avoid interference and to ensure even distribution of clamping forces. Manufacturer: Kukamet Fevzi Çakmak Mah.10644 Sk. No:61-63 42050 Karatay / KONYA TÜRKİYE / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
218mm Clamping Ring For Soft Jaw Inserts - Vertex
Take advantage of precise clamping, compatibility with soft jaw inserts and a compact design that simplifies handling in daily workshop use. The combination of a 218 mm diameter and stable clamping behaviour supports repeatable setups and steady machining results. Order the VFR-08 clamping ring directly via Metav Werkzeuge or ask our consultants if needed. VFR-08 clamping ring — 218 mm diameter for soft jaw inserts (Vertex) The VFR-08 clamping ring is a dedicated clamping accessory designed for use with soft jaw inserts in chuck systems, providing a reliable interface for repeatable workholding across turning and fixture operations. 218 mm diameter for soft jaw setups Precise clamping for stable machining Compact weight at 2.4 kg Consistent accuracy for repetitive turning and fixturing A robust clamping solution delivers predictable results; the clamping ring acts as a uniform radial support when used with soft jaw inserts, ensuring concentric contact and minimised runout. The design focuses on even force distribution rather than aggressive bite, which benefits delicate or reworked components and reduces the need for repeated adjustment. This stability enables consistent cycle times and contributes to higher first-pass accuracy on series parts. Faster changeovers and straightforward integration with chuck systems Integration into established chuck setups is straightforward: the ring is specified for use with an 8-inch chuck jaw system and interfaces with soft jaw inserts to shorten fixture changeovers. Clear mechanical fitment reduces alignment work during setup, which translates into measurable time savings at the machine. Where quick toolchanger-style swaps are not an option, optimised accessory geometry supports efficient manual handling and repeatable repositioning between batches. Practical workshop performance and handling benefits Weighing 2.4 kg, the component is light enough for manual handling yet substantial enough to remain stable under clamping forces, aiding safe and efficient workshop routines. Constructed as a dedicated clamping component, the ring supports processes where controlled pressure and surface protection are required for softer jaws. Availability through a reliable supplier network helps maintain uninterrupted operations in production and repair environments. For compatibility checks, supply options and technical advice on Vertex clamping rings, contact Metav Werkzeuge in Emmerich for local support and precise product matching. Technical Data Article number: VFR-08 GTIN: 4061905086489 Brand: Vertex Data Diameter: 218 mm Weight: 2.4 kg eCl@ss: 20069202 Special features For soft jaw inserts Suitable for 8-inch chuck jaw Category: Vertex FAQ What applications is this clamping ring suitable for? The VFR-08 clamping ring by Vertex is suitable for turning and fixturing operations where soft jaw inserts are used to protect or shape the workpiece surface. Which chuck systems is the ring compatible with? Compatibility is stated as for 8-inch chuck jaw systems; the VFR-08 is intended to integrate with standard 8‑inch jaw configurations and the corresponding soft jaw inserts. How does the ring affect setup time? By providing a defined interface for soft jaws, the clamping ring reduces alignment effort and supports quicker changeovers compared with ad hoc fixturing methods. Is the VFR-08 heavy to handle during manual setup? At 2.4 kg, the VFR-08 offers a balance between manageable handling and sufficient mass for stable clamping, suitable for routine manual installation and removal. Can the clamping ring be used for delicate or reworked components? Yes, when combined with soft jaw inserts the ring provides controlled pressure distribution, making it appropriate for delicate surfaces and reworked parts. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
21mm Ball Washer for M20 Screws D1:21 D3:36 H2:6.3 R:27, DIN 6319C - AMF
Take advantage of the DIN‑compliant fit combined with a Ø21 mm bore and clearly defined seating geometry for reliable bolted assemblies — order directly via Metav Werkzeuge or ask the consultants for application support. Spherical washer DIN 6319C by AMF — for M20 screws, bore Ø21 mm The spherical washer DIN 6319C provides a self‑aligning seating surface for hexagon screw connections, engineered for industrial bolted joints where controlled contact geometry and repeatable alignment are required. DIN 6319C standard compliant Bore Ø 21 mm for M20 screws Outer diameter 36 mm, height 6.3 mm Precision radius R 27 mm Reliable standard compliance for secure connections Meeting DIN 6319C ensures consistent seating and repeatable performance in production and maintenance environments. The standardised geometry minimises misalignment between screw head and component, which reduces the risk of uneven clamping forces and subsequent joint loosening. This results in fewer rework cycles and steadier assembly quality across batches, supporting lean production and predictable maintenance intervals. Precise dimensions that speed up assembly The defined bore of Ø21 mm together with an outer diameter of 36 mm and a height of 6.3 mm provides a tight, predictable fit for M20 fastenings. The specified radius R 27 mm aids in distributing contact stresses evenly, lowering the likelihood of surface indentation or component distortion. Such dimensional clarity simplifies fixture planning and reduces the time spent checking tolerances during installation. Improved joint performance through controlled seating A spherical seating element with correct geometry helps the bolted joint accommodate minor angular deviations without imposing additional bending moments on the screw. The result is a more uniform clamping force and improved fatigue behaviour in cyclic loads. For applications that demand stability under vibration or variable loads, this component supports longer service life and lowers the probability of unscheduled downtime. Practical advantages for workshops and industrial users Supplied by AMF and packaged per unit, the part is suited to both repair shops and production lines that require single‑piece ordering for bespoke maintenance tasks. The compact design and familiar standard make it straightforward to stock as a spare part, while the clearly documented dimensions facilitate integration into inventory systems and CAD libraries. Procurement and supply continuity for professionals The component is identified by SKU 4000833461NW and is available through Metav’s procurement channels; selecting standardised parts like this spherical seating washer simplifies logistics and reduces supplier complexity. Professional purchasers benefit from predictable availability and the documentation necessary for quality management and traceability. Contact Metav Werkzeuge for AMF components and expert guidance on dimensional suitability and stocking strategies — the Metav team provides application advice and reliable supply from Emmerich. Technical data Article number: 4000833461NW Standard: DIN 6319C Type: Spherical washer Facts Bore diameter D1: 21 mm Outer diameter D3: 36 mm Height H2: 6.3 mm Radius R: 27 Packaging unit: 1 Special features Compatible with M20 screws Brand: AMF Label: Spherical washer for M20, bore Ø21 mm FAQ Is this washer suitable for M20 screw connections? Yes. The spherical washer is specified for use with M20 screws and features a Ø21 mm bore for correct fit. Which standard does the component comply with? The part complies with DIN 6319C, ensuring standardised seating geometry and repeatable assembly characteristics. What are the key dimensions to check for installation? Key dimensions are the bore Ø21 mm, outer diameter 36 mm and height 6.3 mm; these determine compatibility with mating parts. Can this washer reduce joint loosening under vibration? Yes. The washer’s spherical seating and radius R 27 mm help distribute loads evenly, improving clamping uniformity and resistance to loosening. How is the part identified for ordering and stock control? The article is listed under SKU 4000833461NW and described as a spherical washer to DIN 6319C for M20. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
21mm Clamping Screw M7 8mm Square For Indexable Holder - TECWERK
Take advantage of a compact spare screw that combines a standard M7 thread, a precise 21 mm overall length and an 8 mm square drive to maintain secure clamping in quick-change turning holders. Order the part directly via Metav Werkzeuge or consult our technicians for compatibility checks and stock advice. Clamping screw Size A, M7, 21 mm, 4-square 8 mm – TECWERK clamping screw for interchangeable holder The Clamping screw Size A, M7, 21 mm is a spare clamping component for TECWERK interchangeable holders for turning tools, designed to secure the insert holder via an 8 mm square drive. Precision spare screw M7 21 mm overall length for compact fit 8 mm square drive for reliable torque Secure fastening that keeps production steady A dedicated M7 clamping screw provides a standardised thread interface that simplifies maintenance and replacement. The 21 mm overall length is suited to compact holders where space is limited, while the 8 mm square drive ensures a secure transfer of torque from the wrench to the clamping element. Engineers benefit from consistent clamping force and predictable assembly behaviour, which together reduce the risk of tool movement and unplanned stoppages. Designed for quick replacement and compatibility As a spare part for TECWERK interchangeable holders, this clamping screw supports quick swaps during tool changes and servicing. The part is intended for use with quick-change turning tool holders that incorporate a prism locating feature; this alignment aid ensures repeatable positioning when the screw is reinstalled. Maintaining a small stock of these screws minimises downtime and keeps change-over procedures lean. Practical workshop handling and inventory benefits Supplied individually, the component is straightforward to store and identify by its thread and drive dimensions. The 4-sided (square) 8 mm drive type is compatible with common workshop spanners and torque tools, making torque application reliable and maintenance predictable. Keeping matching spare screws avoids improvised repairs and supports a consistent toolholding standard across lathe stations, which is essential for quality and repeatability. Contact Metav Werkzeuge to confirm fitment and reserve compatible M7 clamping screws for TECWERK interchangeable holders; our Emmerich-based team will advise on availability and delivery options Technical Data Article number: 2000832427NW Product type: Clamping screw Manufacturer: TECWERK Label: Spannschraube Größe=A M7 L.21mm 4-KT.8mm z.Wechselhalter TECWERK Dimensions and core data Thread: M7 Overall length: 21 mm Square drive: 8 mm Type: A Packaging unit: 1 Applications and special features Spare part for TECWERK interchangeable holder for turning tools and prism Replacement screw for quick-change clamping systems Four-sided drive (4-kt) 8 mm for secure torque transfer Compact dimensions for confined assemblies FAQ What are the thread and length specifications of this clamping screw? The clamping screw is specified with an M7 thread and an overall length of 21 mm; it is listed under SKU 2000832427NW for easy identification. Is this screw compatible with TECWERK interchangeable holders? Yes, the spare clamping screw is intended as a replacement part for TECWERK interchangeable holders for turning tools and the prism locating variant. What drive type is required to tighten the screw? The component uses an 8 mm square drive (4-kt), compatible with common square-drive spanners and torque tools found in workshop tool sets. Manufacturer/Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
21mm Collet 5C Precision Collet, 0.02mm Runout Accuracy - Vertex
Take advantage of the combination of high concentricity (0.02 mm), a 21 mm nominal diameter and a compact 87 mm length for consistent, low-setup machining. Order the collet directly via Metav Werkzeuge or consult the team for application advice. 5C collet — 21 mm precision clamping sleeve by Vertex The 5C collet is a precision clamping sleeve designed for secure toolholding in machining environments where repeatable concentricity and compact reach are required. 21 mm nominal diameter Concentricity 0.02 mm accuracy Length 87 mm for deeper reach Manufacturer Vertex Precision that reduces rework and cycle variation A concentricity specification of 0.02 mm provides a measurable basis for improved machining accuracy. Reduced radial runout means less vibration and lower risk of dimensional deviation during turning or milling, which translates into fewer rejects and less rework. The combination of tight concentricity and a 21 mm bore is beneficial where small tolerances are mandatory; the result is a more stable spindle behaviour and predictable part quality. The stated accuracy is a clear, verifiable performance indicator for process control. Compact design for reliable clamping and accessible tool placement With a length of 87 mm and a weight of 0.21 kg, the collet offers a balance between secure clamping and compact installation. The shorter profile helps to reduce overhang and improve rigidity in the toolholder, supporting higher cutting stability. Mass is kept low to avoid unnecessary spindle load while maintaining robust clamping force. In practice, this means longer tool life and reduced tool-change downtime where access and space are limited. Material-neutral specification and workshop integration As a component from Vertex, the collet is intended for integration into standard 5C toolholding systems and workshop workflows that require reliable repeatability. The item is identified by SKU 5C-21 and can be referenced directly for procurement and inventory. Where exact material compatibility is relevant, process engineers can align clamping choice with tooling and workpiece materials to ensure optimal cutting performance and safety. Clear data such as diameter, length and accuracy allow straightforward comparison during purchasing and process planning. Contact Metav Werkzeuge in Emmerich for tailored advice on integrating the Vertex 5C collet into production—consultants are available at info@metav-werkzeuge.com or by telephone on +49 2822 7131930. Technical data Article number: 5C-21 GTIN: 4061905090332 Manufacturer: Vertex eClass: 21041712 Facts Diameter: 21 mm Length: 87 mm Accuracy: 0.02 mm Weight: 0.21 kg Special features Type: 5C collet Brand: Vertex SKU: 5C-21 Image available: 5c-3-main.jpg FAQ What machining benefit does the 0.02 mm concentricity offer? The 0.02 mm concentricity of the Vertex 5C collet reduces radial runout, improving surface finish and dimensional accuracy while lowering scrap rates in precision turning and milling operations. Is this collet compatible with standard 5C toolholders? Yes, the product is a 5C collet (SKU 5C-21) and is intended for use with standard 5C toolholding systems, enabling straightforward integration into existing setups. How does the 87 mm length affect rigidity and reach? The 87 mm length provides a compact reach that reduces overhang compared with longer holders, increasing rigidity and enhancing cutting stability for delicate or high-precision tasks. Where can the Vertex 5C collet be sourced and who to contact for technical queries? The Vertex 5C collet (SKU 5C-21) can be ordered via Metav Werkzeuge; for technical questions Metav’s consultants can be contacted by email or phone as provided in the product listing. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
21mm Hexagon Nut DIN 6331 M14 Machined Faces Strength Class 10 - AMF
Take advantage of the combination of DIN 6331 standardisation, strength class 10 reliability and precise dimensions for consistent, high‑force clamping in production. Order the AMF hexagon nut directly via Metav Werkzeuge or consult our specialists for specification support. Hexagon nut DIN 6331 M14 – SW 21 mm, strength class 10 (AMF) Hexagon nut DIN 6331 M14 engineered as a high‑strength metric fastening solution for industrial assemblies and machine construction DIN 6331 compliance for interchangeability Strength class 10 for high clamping loads SW 21 hexagon for standard spanners Compact overall height of 21 mm for tight spaces Consistent clamping force for heavy‑duty joints The M14 thread in combination with strength class 10 provides a clear advantage where elevated clamping forces are required. The reinforced material grade behind this classification allows the fastener to transmit higher preload without premature deformation, which directly improves joint reliability in production environments. For engineers and assemblers this means fewer re‑work cycles and a lower risk of joint loosening under dynamic loads, translating into measurable process stability. Standardised form for rapid assembly and serviceability Compliance with DIN 6331 and the standard SW 21 across the hexagon faces ensures compatibility with common tools and automated tightening equipment. The specified overall height 21 mm and corner‑to‑corner dimension 23.4 mm (Eckenmaß) support predictable wrench engagement and torque application. The pressed and milled manufacturing method yields defined contact faces and accurate geometry, which improves torque transfer and reduces the chance of rounding during tightening — a practical benefit for maintenance intervals and in-line assembly. Reduced assembly time and dependable inventory handling Using a standardised hexagon nut like this AMF fastener simplifies procurement and stock management: metric thread designation M14, clear article identification and single‑unit packaging keep logistics straightforward. The compact design supports installation in confined assemblies without compromising load capacity. For operations managers this reduces inventory complexity and supports just‑in‑time workflows while maintaining the required mechanical performance. Contact Metav Werkzeuge for specification advice and secure supply of AMF hexagon nuts in strength class 10 to suit production demands Technical data SKU: 4000833411NW Type: M14 Standard: DIN 6331 Brand: AMF Facts Overall height: 21 mm Spanner width: 21 mm Corner across corners: 23.4 mm Strength class: 10 Packaging unit: 1 Special features Pressed and milled manufacturing Metric thread, hexagon profile Designed for industrial bolted joints Compact design for space‑restricted assemblies FAQ What load capacity can be expected from this nut? The Hexagon nut DIN 6331 M14 (AMF, SKU 4000833411NW) is rated strength class 10, which indicates suitability for high clamping loads in industrial bolted connections when used with appropriate bolts of matching strength. Is the nut compatible with standard spanners and sockets? Yes, the nut features SW 21 across‑flat width, making it compatible with standard spanners and socket tools commonly found in workshops and automated tooling stations; the M14 designation matches standard metric bolts. How does the pressed and milled finish affect assembly? The pressed and milled production results in accurate seating faces and defined hexagon edges, improving torque transfer and reducing the chance of rounding during tightening on the AMF hexagon nut. Can this nut be used in compact assemblies? With an overall height of 21 mm and a compact hexagon profile, the Hexagon nut DIN 6331 M14 is designed for installations where space is limited but reliable clamping is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
21mm Hexagon Nut M14 DIN 6330B Strength Class 10, Height 21mm - AMF
Reliable fastening for mechanical assemblies is achieved by the M14 thread and strength class 10 combined with a 21 mm spanner width, ensuring consistent clamping force and repeatable installation; order this component directly via Metav Werkzeuge or consult the technical advisors for specification matching. Hexagon nut DIN 6330B M14 — high-strength fastening, 21 mm across-flats (AMF) The Hexagon nut DIN 6330B M14 provides a standardised, high-strength fastening solution for mechanical assemblies, maintenance and machine construction where secure bolted connections are required. Strength class 10 for high clamping force Complies with DIN 6330B standard 21 mm across‑flats for secure wrenching Robust performance for demanding bolted joints The fastener is specified to DIN 6330B and manufactured to deliver reliable mechanical behaviour under load. With a nominal thread of M14 and strength class 10, the component offers superior clamping capacity compared with lower grades, which reduces the risk of loosening in dynamic applications. The standard conformity simplifies selection and quality assurance processes in industrial procurement and supports predictable assembly behaviour in production environments. Precise geometry for correct tool engagement and assembly Measured dimensions such as 21 mm across‑flats and an overall height of 21 mm ensure compatibility with common spanner and socket tools, improving assembly speed and torque transmission. The listed corner width of 23.40 mm provides the geometric context for handling and clearance calculation in tight assemblies. These precise measures make inventory management easier and reduce downtime caused by mismatched tooling or incorrect fastener choices. Simplified sourcing and traceability for workshop supply chains Marked with the AMF designation and the SKU, the component integrates into standard procurement and storage routines. The compact packaging unit (1) is suitable for targeted replacement tasks and small-batch maintenance orders. Clear standardisation, visible on the fastener, supports traceability and documentation in quality systems and helps reduce the administrative overhead when specifying replacement or spare parts for production lines. For technical advice on AMF hexagon nuts or to source DIN 6330B fasteners directly, contact Metav Werkzeuge for expert assistance and reliable supply. Technical data Article number: 4000833396NW UID: 4000833396NW Brand: AMF Product type: Hexagon nut Standard: DIN 6330B Numbers / Core technical data Thread size: M14 Across‑flats (spanner size): 21 mm Overall height: 21 mm Corner width: 23.40 mm Strength class: 10 Packaging unit: 1 Features / Standards Hexagon nut design Strength class 10 indicated DIN 6330B compliance SKU: 4000833396NW Intended for mechanical assembly and maintenance FAQ What does DIN 6330B signify for this fastener? DIN 6330B denotes the dimensional and geometric standard to which the hexagon nut conforms, ensuring that the Hexagon nut DIN 6330B M14 fits and functions with mating parts produced to the same norm. How does strength class 10 affect application? Strength class 10 indicates a high-strength grade; the AMF hexagon nut with this rating provides greater clamping capability than lower classes, making it suitable for joints subject to elevated stresses. Which spanner or socket fits this nut? A 21 mm across‑flats dimension requires a 21 mm spanner or socket for correct torque application to the M14 hexagon nut (SKU 4000833396NW). Is the overall height relevant for installation? Yes, the overall height of 21 mm influences thread engagement depth and clearance calculations; this geometric data assists in specifying compatible bolts and washers for secure assemblies. What is the packaging unit and how is it supplied? The item is supplied in a packaging unit of 1, enabling single-part replacement and controlled procurement for maintenance tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
21mm Hexagon Nut M14 SW22 Pressed And Milled Strength Class 10 AMF - AMF
Combine high tensile capacity and precise DIN 6331 geometry for dependable bolted connections; the M14 hexagon nut provides secure clamping with standardised fit and measurable torque behaviour. Order the AMF hexagon nut directly via Metav Werkzeuge or ask the consultants for specification advice. AMF Hexagon Nut M14 (DIN 6331) — SW 22, Strength Class 10, Pressed and Milled The AMF Hexagon Nut M14 (DIN 6331) is a high-strength fastening element designed for industrial assemblies where standard conformity and repeatable clamping force are required. Hexagon nut M14 to DIN 6331 specification Strength class 10 for high clamping loads Spanner width 22 mm, corner size 24.5 mm Pressed and milled finish, overall height 21 mm Engineered for dependable clamping performance The design follows DIN 6331, which guarantees thread and form compatibility with standard bolts and reduces the risk of joint failure in production environments. With strength class 10, the component is rated for elevated tensile and yield limits, so assemblies subject to dynamic or high static loads can be calculated with confidence. The metric M14 thread is a common industrial dimension; its predictable load-bearing behaviour simplifies selection for fixtures and structural joints. This results in fewer rejects and a more stable production process when the correct tightening procedures are applied. Precision geometry that simplifies assembly and maintenance A defined spanner width of 22 mm and a corner size of 24.5 mm ensure consistent engagement with conventional tools, reducing the chance of rounding and tool slippage during torqueing. The pressed and milled finish produces flat seating faces and accurate flank contact, which lowers stress concentrations and improves clamping distribution. The overall height of 21 mm provides sufficient thread engagement for standard bolts, enabling reliable torque transmission while retaining accessibility for maintenance operations. Such geometry is particularly beneficial where reproducible torque is required across multiple joints. Application scope and practical benefits in workshop and industrial use The component is suitable for bolted joints in machines, jigs, and structural assemblies where standardised parts are preferred for interchangeability. Compliance with DIN 6331 facilitates procurement and quality control, since the fastener can be inspected against recognised tolerances. Supplied individually (packaging unit 1), the item is convenient for replacement tasks or small-batch assembly. For customers requiring additional verification, technical documentation and specification checks can be provided to match the nut to bolt grade and application-specific torque charts, supporting safe and efficient engineering decisions. For secure, standard-compliant fastening solutions, rely on AMF components supplied through Metav Werkzeuge — contact the Metav consultants at info@metav-werkzeuge.com or +49 2822 7131930 for specification matching and reliable supply from Emmerich. Technical data Article number: 4000833412NW Product type: Hexagon nut Brand: AMF Facts Thread size: M14 Overall height: 21 mm Spanner width: 22 mm Corner size: 24.5 mm Strength class: 10 Special features Standard: DIN 6331 Finish: pressed and milled Packaging unit: 1 FAQ What load class does this nut meet and why does it matter? The AMF hexagon nut is specified as strength class 10, which indicates higher tensile and yield properties suitable for assemblies subject to elevated clamping forces; this allows safer design margins where stronger bolted joints are required. Is the nut compatible with standard M14 bolts to DIN specifications? Yes, the item conforms to DIN 6331 and is dimensioned for M14 threads, ensuring interchangeability with bolts produced to the same standard. Which spanner size is required for assembly? A spanner width of 22 mm is required; the corresponding corner size is 24.5 mm, which supports secure tool engagement and consistent torque application. How does the pressed and milled finish affect performance? The pressed and milled finish yields accurate seating faces and reduced form deviation, which improves load distribution and lowers the potential for fretting or uneven clamping in long-term service. Can the nut be used for high-vibration applications? Given the strength class 10 rating and precise geometry, the nut is suitable for applications with dynamic loads when combined with the correct bolt grade and appropriate locking methods. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
21mm Washer DIN 6340 For M20 Bolts 50mm Outer Diameter 6mm Thick - AMF
Benefit from DIN 6340 conformity, a 21 mm bore tailored for M20 fastenings and a robust 6 mm thickness that delivers reliable load distribution; order directly via Metav Werkzeuge or consult our technical advisers for specification support. U-washer (DIN 6340) for M20 screws, bore Ø21 mm – AMF A U-washer (DIN 6340) engineered to ensure secure M20 screw connections in industrial assemblies and standard workshop applications. DIN 6340 compliant 21 mm bore for M20 bolts 6 mm robust thickness 50 mm outer diameter Consistent standard compliance for predictable assemblies Conformity with DIN 6340 guarantees dimensional accuracy and repeatable fit, which reduces variations in production and maintenance. For procurement and inventory planning this standardisation means fast replacement and assured interchangeability. The compliance also simplifies quality control procedures: inspection protocols can reference the recognised DIN tolerances rather than bespoke measurements, saving time in acceptance testing and enabling predictable joint behaviour in series assemblies. Optimised geometry for M20 bolting and pressure distribution The combination of a 21 mm bore, a 50 mm outer diameter and 6 mm thickness provides effective surface contact and even stress distribution beneath the bolt head or nut. The slightly oversized outside diameter lowers the unit pressure on softer substrates, limiting embedment and preserving component surfaces. Where a reliable clamp force is required, this form factor improves joint stiffness and reduces the risk of localised deformation, making the AMF washer a practical choice for heavy-duty threaded connections. Practical benefits in workshop and industrial use With its standardised design, the washer supports streamlined assembly workflows and reduces rework. The U-washer is suitable for repeat installations and maintenance cycles where consistent joint behaviour is critical. Because the component is manufactured to a recognised standard, documentation and parts lists remain concise and unambiguous, which helps logistics and service teams speed up repairs and lowers the risk of incorrect part selection. How the washer improves bolted-joint performance Beyond basic spacing, the primary function is load distribution and protection of the clamped surfaces. By increasing contact area, the washer reduces localised stress peaks and helps maintain clamp preload under dynamic loads. In applications combining metric M20 bolts with standard nuts or heads, this washer complements torque settings by offering a predictable interface that supports reliable clamp force transmission and longer joint life. For specification advice or to secure standard-compliant AMF washers for M20 applications, contact Metav Werkzeuge in Emmerich for tailored recommendations and prompt supply: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 4000833442NW SKU/UID: 4000833442NW Manufacturer: AMF Product type: Washer Standard: DIN 6340 Dimensions / Core data Bore diameter (D1): 21 mm Outer diameter (D2): 50 mm Thickness (S): 6 mm Suitable for: M20 Packaging unit: 1 Features / Applications For use with M20 bolts and standard nuts Standardised geometry for interchangeability Designed for industrial and workshop assemblies Label: U-Scheibe DIN 6340 f.Schrauben M20 Bohrungs-D.21mm AMF FAQ What standard does this washer comply with? The washer complies with DIN 6340, ensuring standardised dimensions and tolerances for reliable replacements. Is the bore size suitable for M20 bolts? Yes, the 21 mm bore is specified for M20 threaded connections and pairs correctly with standard M20 bolts and nuts. What are the key dimensions to check for compatibility? Check the 21 mm bore, 50 mm outer diameter and 6 mm thickness to ensure compatibility with mating components and surface load requirements. Can this washer be used in heavy-duty clamping applications? The washer’s 6 mm thickness and wide outer diameter provide improved load distribution, making it suitable for many heavy-duty bolted joints. Which SKU identifies this AMF washer? The product is listed under SKU/UID 4000833442NW, labelled as a DIN 6340 washer for M20 screws. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
21x32mm Coupling M12x1.75mm Threaded, 65g - Vertex
Take advantage of a compact 21×32 mm footprint and a standard M12×1.75 threaded connection to achieve reliable mechanical joins with minimal installation time; the low mass of 0.065 kg reduces moving-part inertia and helps maintain cycle consistency on assembly lines. Order the coupling directly via Metav Werkzeuge or consult our advisors for application guidance. 2614M coupling by Vertex — M12×1.75 thread, compact 21×32 mm design The 2614M coupling is a compact mechanical connector designed for secure joining in clamping and fixture applications across workshops and light industrial assemblies. Compact 21×32 mm footprint M12×1.75 threaded connection Lightweight at 0.065 kg Reliable connections in a confined space The small 21×32 mm form factor delivers a space-saving option where clearance is limited, while the standard M12×1.75 thread ensures compatibility with a wide range of fastening components. The compact design translates into easier integration into existing fixtures and tooling without compromising joint integrity. By prioritising a minimal profile, the component helps maintain accessibility around assemblies and reduces the need for larger adapters or rework during retrofits. This makes it particularly suitable for machine enclosures, jig fixtures and compact assemblies where every millimetre of clearance matters. Faster assembly and lower dynamic load With a mass of 0.065 kg, the coupling contributes to lower rotating or reciprocating mass on moving subassemblies, which can improve cycle stability and reduce bearing stress over time. The standard threaded interface facilitates a quick-fit installation using common M12 tooling, cutting assembly time and simplifying inventory decisions. The straightforward mechanical design eliminates complex alignment procedures, enabling maintenance teams to replace or reconfigure connectors quickly and with repeatable results. These practical advantages support throughput improvements and predictable downtime windows. Consistent quality and broad application scope Manufactured by Vertex, the component is intended for robust workshop and light industrial use, offering a dependable option for clamping technology and fixture setups. The precise external dimensions and standardised thread form support predictable mating and repeatable clamping forces when used with appropriate fasteners. For procurement and systems engineering, the combination of compactness, standard interface and low weight represents a practical balance between installation convenience and operational reliability. Technical clarification or compatibility checks are available for bespoke assemblies with unusual tolerances or environmental requirements. Choose Vertex's 2614M coupling for compact, standard-threaded connections — order via Metav Werkzeuge or contact our consultants for specification support and application advice Technical Data Article number: 2614M GTIN: 4061905093241 Manufacturer: Vertex ECLASS: 21131711 Facts Dimensions: 21×32 mm Weight: 0.065 kg Thread: M12×1.75 mm Special features Compact design for restricted spaces Standard M12×1.75 threaded connection Suitable for clamping and fixture applications FAQ What is the thread specification of the coupling? The coupling features a standard M12×1.75 mm threaded connection for compatibility with common fasteners and fittings. What are the external dimensions and weight? External dimensions are 21×32 mm and the weight is 0.065 kg, making the component suitable for compact assemblies. Is the coupling suitable for fixture and clamping technology? Yes, the design is intended for clamping and fixture applications where a compact, standard-threaded connector is required. Who manufactures the 2614M coupling? The coupling is manufactured by Vertex, a producer of precision mechanical components. How does the compact design benefit an assembly? The small footprint reduces spatial conflicts, simplifies retrofits and helps lower moving-part inertia in dynamic subassemblies. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
21x32mm Coupling M14x2mm Threaded, 60g Lightweight - Vertex
The compact dimensions and standard M14×2 mm thread ensure straightforward integration into confined assemblies, while the low mass supports easy handling and storage; order the part directly via Metav Werkzeuge or consult Metav's advisers for specification matching. Coupling 2614M-1 — compact mechanical coupling with M14×2 mm thread (Vertex) The Coupling 2614M-1 is a compact mechanical connector intended for precise joining of threaded components in small assemblies and workshop fixtures. Compact 21 x 32 mm design Threaded connection M14×2 mm Lightweight 0.06 kg Space-saving fit for tight assemblies The compact footprint of the component, specified as 21 x 32 mm, makes it suitable where installation space is limited. The small external dimensions permit installation in confined fixtures and compact machine modules without extensive rework of adjacent parts. The reduced envelope helps preserve existing clearances and supports denser component layouts while maintaining a secure mechanical joint. Standardised thread for reliable mating A defined M14×2 mm thread enables secure, repeatable connections with components that conform to common metric thread standards. Using a standardised thread size simplifies parts selection and reduces the need for bespoke adaptors. The standard thread also helps maintain consistent torque characteristics and predictable clamping when assembled with appropriate fasteners or mating parts. Clear identification for inventory and traceability The item is supplied under SKU 2614M-1 and is registered with GTIN 4061905091995, which supports efficient stock management and traceability across supply chains. Clear identifiers simplify reordering, prevent part-mix errors and allow rapid reconciliation of consignments. Technical drawings and detail images are available to verify fit before installation. Practical benefits for workshop handling and logistics With a mass of only 0.06 kg, the component is easy to handle during assembly and reduces shipping weight across larger orders. The compact and light design also reduces storage footprint and facilitates faster throughput in assembly processes. Supplied by Vertex, the part aligns with expectations for consistent manufacture and batch identification, supporting quality control routines and standard procurement processes. For specification checks or to confirm compatibility with an application, contact Metav Werkzeuge in Emmerich — request detailed drawings or place an order via email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data Article number: 2614M-1 GTIN: 4061905091995 Manufacturer: Vertex Facts Dimensions: 21 x 32 mm Thread: M14×2 mm Weight: 0.06 kg Special features ECLASS: 21131711 Images: technical drawing and detail view available SKU: 2614M-1 FAQ What is the thread size of this coupling? The coupling is manufactured with an M14×2 mm thread, as specified for Vertex Coupling 2614M-1 What are the external dimensions and weight? Dimensions are 21 x 32 mm and the mass is 0.06 kg for the Vertex part listed as SKU 2614M-1 How is the part identified for ordering and inventory? Identification is via SKU 2614M-1 and GTIN 4061905091995, which should be used for procurement and stock control Are technical drawings available to check fitment? A technical drawing and detailed images are available to verify installation and are linked to the product data for the Vertex coupling Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
22 mm T-Slot Nut Single M20 Thread - Vertex
Benefit from reliable compatibility with common 22 mm T-slots and a robust M20 thread for secure clamping and reduced set-up time; order genuine Vertex parts via Metav Werkzeuge or consult our experts for integration advice. 3417M — T-slot nut, 22 mm T-slot, M20 thread (Vertex) The 3417M is a single T-slot nut designed for secure fastening in machine tables and fixtures, compatible with standard 22 mm T-slots for general workshop and industrial clamping applications. Compatible with 22 mm T-slots M20 threaded for heavy-duty fixings Single-piece design for easy installation Secure clamping where it matters The T-slot nut provides a straightforward solution for anchoring fixtures and accessories to machine tables. With a 22 mm T-slot compatibility and an M20 thread, the component delivers a stable connection between the table and the fastening bolt, reducing lateral movement under load. This solidity supports consistent positioning of jigs and stops, which in turn helps to maintain repeatable machining results and minimise downtime caused by retightening. The proven geometry of the fastener simplifies selection for standardised systems and supports efficient workshop workflows. Streamlined workflow and inventory benefits A single-piece design reduces assembly steps and simplifies stock keeping for production and maintenance departments. Instead of multiple complex components, the compact fastener serves as a readily available fixing element for routine set-ups. For teams managing several machines or fixtures, this reduces the variety of spare parts required and speeds up clamping changes during tool or job swaps. The item’s clear SKU reference and standard interface make ordering and replacement straightforward, supporting uninterrupted operation on the shop floor. Integration, compatibility and practical considerations The fastener uses an M20 thread, compatible with standard M20 bolts and nuts, enabling direct pairing with widely available fixings. When integrating the part into an assembly, ensure proper thread engagement and appropriate tightening torque as specified for the mating bolt to achieve the intended clamping force; consult machine or fixture guidelines where necessary. The GTIN and SKU provided with the component allow exact identification for procurement and asset tracking, reducing the risk of mismatched parts and supporting traceability in industrial environments. Secure workshop compatibility with genuine Vertex components — request the 3417M T-slot nut via Metav Werkzeuge or contact our consultants for specification checks and stock information Technical Data SKU: 3417M GTIN: 4061905090219 Manufacturer: Vertex Facts Dimensions: 21.7x38x14 mm T-slot compatibility: 22 mm Thread: M20 eClass: 21029107 Special features Designation: T-nut Version: single-piece Brand: Vertex Available assets: technical drawing and detail images FAQ What is the intended use of this T-slot nut? The 3417M T-slot nut is intended as a fastening element for machine tables and fixtures that use a 22 mm T-slot, providing a threaded anchor point for M20 bolts. Is the 3417M compatible with standard M20 bolts? Yes, the 3417M uses an M20 thread and is compatible with standard M20 bolts and nuts when correct thread engagement is observed. How does the single-piece design benefit workshop operations? A single-piece configuration reduces assembly complexity and spare parts variety, simplifying logistics and enabling faster fixture set-up during production changes. Can the 3417M be used across different machine tables? The component is compatible where a 22 mm T-slot is present; verify slot dimensions and clearances before installation to ensure proper fit on the specific table. How can the part be identified for ordering or inventory? Use the SKU 3417M and the GTIN 4061905090219 to ensure exact identification when procuring or logging the item. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
220mm Self-Centring Extra-Flat 3-Jaw Lathe Chuck 1800 kgf - Vertex
Take advantage of the combination of robust clamping performance and a low-profile, space-saving design for efficient, repeatable turning. The self-centring mechanism and high clamping force ensure fast set-up and secure workholding — order the 3-jaw chuck directly via Metav Werkzeuge or ask our consultants for installation advice. Vertex VNBK-6 3-jaw lathe chuck — self-centring, extra-flat, 220 mm The Vertex VNBK-6 3-jaw lathe chuck is a self-centring, extra-flat chuck engineered for reliable clamping on turning machines and lathes Self-centring, extra-flat design 220 mm outer diameter 1,800 kgf clamping force Robust construction, 12.4 kg weight Faster set-up through reliable centring The self-centring jaw system reduces set-up time by aligning workpieces automatically when clamped, so changeovers are quicker and repeatability is improved. For batch production and frequent part changes, this mechanism minimises manual adjustment and the associated downtime. The three-jaw arrangement distributes force evenly for consistent positioning, which is particularly advantageous when a precise concentric hold is required for turning operations. High clamping force for stable turning Designed to deliver 1,800 kgf of clamping force, this chuck provides a firm grip that reduces the risk of slippage during heavy cuts or interrupted machining. The 220 mm diameter suits medium-sized components and offers a balance between accessibility and holding capacity. The VNBK-6 is specified to maintain secure contact under operational loads, helping to protect tooling and workpieces while supporting higher material removal rates where process stability is essential. Low-profile design for improved access and safety The extra-flat profile shortens the distance between the workpiece and the spindle, improving tool clearance and accessibility for the cutting tool. As a lathe chuck with a compact form, it reduces overhang and the lever effect on the spindle, which can help to lower dynamic loads and vibration. The robust build, reflected in a 12.4 kg mass, contributes to stable rotation while keeping the footprint minimal for tighter setups on modern turning centres. Contact Metav Werkzeuge for tailored advice and to reserve the Vertex VNBK-6 self-centring 3-jaw chuck for prompt dispatch from Emmerich. Technical Data Article number: VNBK-6 GTIN: 4061905083181 eClass: 21020401 Category: Vertex Dimensions & Performance Diameter: 220 mm Weight: 12.4 kg Clamping force: 1,800 kgf Features & Materials Type: Three-jaw lathe chuck Design: Self-centring, extra-flat Weight indication included in specifications FAQ What is the main advantage of a self-centring chuck? A self-centring chuck like the Vertex VNBK-6 aligns workpieces automatically when the jaws are tightened, reducing set-up time and improving concentricity for repeat operations. Which machines is this chuck suitable for? The VNBK-6 is intended for installation on turning centres and lathes that accept a 220 mm chuck and can accommodate the chuck's mass and mounting requirements. How much clamping force does the chuck provide? The chuck delivers a clamping force of 1,800 kgf, which is designed to hold components securely during demanding turning operations. Does the low-profile design affect accessibility? Yes, the extra-flat design shortens the spindle-to-workpiece distance, improving tool access and reducing overhang compared with taller chuck designs. Is the chuck balanced for high-speed use? The VNBK-6 is built for stable rotation; balancing requirements depend on the specific machine and operating speeds, and final balancing is recommended according to the lathe manufacturer's guidance. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
220mm Waterproof Lamp Halogen or LED, Light IP67 Arm IP20 - Vertex
Take advantage of the combination of robust waterproofing, flexible positioning and dual-voltage compatibility for continuous workshop illumination; order the lamp directly via Metav Werkzeuge or consult our experts for tailored advice. Lamp VHL-400M – Waterproof inspection lamp, halogen or LED, Vertex The Lamp VHL-400M is a waterproof industrial inspection lamp designed for workshop and maintenance tasks, offering halogen or LED compatibility and a stable articulated arm for precise positioning Waterproof light housing (IP67) Adjustable 220x220 mm arm Dual voltage: 110V / 220V Compatible with halogen 12V/50W or LED Consistent illumination where accuracy matters The head's IP67 rating ensures reliable performance in wet or oily environments, keeping the light source protected against dust and temporary immersion. With 110V/220V compatibility and options for halogen or LED fittings, the unit delivers dependable brightness without complex electrical conversions. This combination of sealed protection and versatile power support reduces installation complexity and allows continuous operation across different workshop power supplies, helping maintain steady inspection conditions and minimise production interruptions. Precise positioning for detailed work An articulated 220x220 mm arm provides controlled reach and micro-adjustments for close-up inspection, while the assembly's overall 3.5 kg mass contributes to stability during extended use. The arm is finished to an IP20 standard, offering mechanical protection where the head needs more environmental sealing than the support structure. This design supports repeatable placement and reduces the time spent re-aiming the light, improving workflow efficiency when examining components or performing assembly and repair tasks. Workshop-ready design that supports uptime Compatibility with 12V/50W halogen bulbs or retrofit LED modules makes the unit adaptable to varying lighting preferences and energy strategies, enabling an easy transition to more efficient illumination without replacing the fixture. Built for the demands of routine workshop use, the construction emphasises durability and serviceability to limit replacement cycles and downtime. As a Vertex product, the lamp meets industrial expectations for sturdy performance and straightforward integration into existing workstations and inspection setups. For waterproof, dependable workshop lighting from Vertex, contact Metav Werkzeuge in Emmerich to discuss the VHL-400M and obtain individual technical guidance Technical data Article number: VHL-400M GTIN: 4061905091483 Manufacturer: Vertex Machinery Works Co., Ltd. ECLASS: 27110640 ETIM: EC001959 Facts Weight: 3.5 kg Arm dimensions: 220 x 220 mm Voltage: 110 V / 220 V Light power (halogen): 12 V / 50 W Special features Light head protection: IP67 Arm protection: IP20 Compatible with halogen or LED fittings Workshop inspection application FAQ Is the lamp suitable for use in wet or oily environments? Yes. The VHL-400M features a IP67 rated light head providing protection against dust and temporary immersion, while the articulated arm has IP20 protection. Can the lamp operate on both 110V and 220V supplies? Yes. The lamp supports 110V/220V, allowing use across common workshop power systems without additional transformers. Does the unit accept LED bulbs or only halogen? The lamp is compatible with halogen 12V/50W fittings and can be fitted with LED alternatives where appropriate, enabling energy-efficient retrofits. How does the arm support precise positioning during inspections? The articulated 220x220 mm arm offers controlled reach and repeatable positioning, and the fixture's 3.5 kg weight contributes to stability for detailed inspection work. Is the lamp suitable for industrial inspection tasks? Yes. Designed by Vertex for workshop and inspection environments, the VHL-400M combines robust sealing, adaptable power options and stable mounting for routine industrial use. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
220x110x6mm Plastic Holder For VMS-5 Collets, Lightweight 0.2kg - Vertex
Compact and lightweight storage with a focus on organisation and protection: the plastic construction and the compact dimensions 220 x 110 x 6 mm keep VMS-5 collet sleeves ready for use while saving bench space. Order the VMS-5 Plastic Holder directly via Metav Werkzeuge or ask our consultants if needed. VMS-5 Plastic Holder for Collet Sleeves – Compact 220 x 110 x 6 mm by Vertex The VMS-5 Plastic Holder is a compact storage solution for workshop and tooling environments, engineered to keep VMS-5 collet sleeves organised and protected within a small footprint. Durable plastic construction Compact 220 x 110 x 6 mm format Lightweight at just 0.2 kg Designed for VMS-5 collet sleeves Better organisation, less downtime A streamlined storage solution reduces searching and handling time, directly supporting workflow efficiency. The plastic tray is shaped for orderly placement of collet sleeves, enabling quick access and clear separation of tooling. With a compact footprint of 220 x 110 x 6 mm, the tray fits into standard tool cabinets and bench shelving, contributing to a tidier workstation and fewer misplaced parts. This organisation helps to maintain production rhythm and minimise interruptions. Robust protection without bulk Made from resilient plastic, the holder offers protection from knocks and contamination while remaining exceptionally lightweight at 0.2 kg. The low mass minimises stress on storage systems and makes handling effortless during tool changes. The material resists common workshop soiling and is easy to wipe clean, preserving the condition of stored components and reducing maintenance of both holder and tooling. Such protection supports consistent clamping performance and prolongs the service life of precision parts. Easy integration into existing setups The holder is designed specifically for VMS-5 collet sleeves and adapts well to established tool-storage arrangements. Its slim profile saves shelf depth and allows several units to be placed side by side, creating modular storage arrays for different sleeve sizes or types. The simple, functional design requires no additional fixtures and can be combined with bench organisers or drawer inserts to form a compact, efficient storage system that helps maintain order in busy shops. Secure organised clamping storage with the Vertex VMS-5 Plastic Holder — contact Metav Werkzeuge in Emmerich for technical advice and reliable supply. Technical Data Article number: VMS-5 GTIN: 4061905084768 Manufacturer: Vertex Machinery Works Co., Ltd. Material: Plastic Dimensions: 220 x 110 x 6 mm Weight: 0.2 kg Facts Dimensions (L x W x H): 220 x 110 x 6 mm Weight: 0.2 kg ECLASS: 21022190 GTIN numeric: 4061905084768 Special features For collet sleeves: VMS-5 Brand: Vertex Compact, low-profile design Easy-to-clean plastic material FAQ How compatible is the holder with different collet sleeve types? The VMS-5 Plastic Holder is designed specifically for VMS-5 collet sleeves and provides correct seating and separation for that sleeve type, ensuring consistent organisation for compatible tooling. What material is the holder made from and how durable is it? The Vertex VMS-5 plastic holder is manufactured from a resilient plastic that resists workshop dirt and provides impact protection while remaining lightweight for easy handling. Can the holder be used in drawers or on open shelving? The slim 220 x 110 x 6 mm profile makes the holder suitable for both drawer storage and open bench shelving, allowing modular arrangement alongside other workshop organisers. Does the holder require special maintenance? Maintenance is minimal: the plastic surface can be wiped clean with a cloth; the design of the VMS-5 holder avoids crevices that trap debris, simplifying routine upkeep. Is the product identified for ordering by a catalogue number or GTIN? Yes, the holder is listed under article number VMS-5 and GTIN 4061905084768 for straightforward procurement and inventory management. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
220x220mm Waterproof Inspection Light Halogen/LED 12V–24V, Light IP67 Arm IP65 - Vertex
Reliable workshop illumination that pairs a waterproof lamp head with a sturdy articulated arm to keep inspection tasks precise and uninterrupted; benefit from flexible halogen or LED configurations and dual-voltage compatibility for different workshop supplies. Order the VHL-500M directly via Metav Werkzeuge or consult our specialists for technical clarifications and delivery options. VHL-500M – Industrial inspection lamp with IP67 head and 220 x 220 mm arm (Vertex) The VHL-500M is a waterproof industrial inspection lamp designed for focused illumination in workshops and production lines, offering halogen or LED operation and a compact articulated arm for accurate positioning Robust head with IP67 protection Flexible 220 x 220 mm articulated arm Halogen or LED options for versatile lighting Continuous protection for reliable inspection work The lamp combines an IP67-classified light head with an IP65-rated arm to provide high resistance to dust and water ingress, ensuring reliable illumination even in demanding workshop environments. An IP67 head means temporary immersion protection for the light unit, while the IP65 arm prevents dust and low-pressure water jets from affecting articulation; this reduces downtime and the need for frequent replacements. Such protection supports consistent visual inspections and measurement tasks in metalworking and assembly areas. Precise positioning and adaptable light output The compact 220 x 220 mm articulated arm enables fine adjustment of light direction, improving visibility in tight or congested working spaces. Options for halogen (12 V/50 W – 24 V/50 W) or LED illumination accommodate different inspection needs: halogen lamps deliver concentrated, warm light for contrast-critical tasks, while LED variants typically offer longer life and lower heat generation for continuous use. The unit accepts 110 V/220 V mains supplies, increasing compatibility with varied workshop electrical systems. Built for workshop practicality and easy integration With a net weight of approximately 3.8 kg, the lamp balances stability and manoeuvrability for bench or fixed installations. The design suits routine inspection, maintenance benches and precision assembly stations where consistent, glare-free illumination is essential. Electrical compatibility and the choice between lamp technologies simplify integration into existing setups and make the unit a practical choice for facilities seeking durable, serviceable lighting that supports quality control processes. For specification advice or to order the Vertex VHL-500M, contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or call +49 2822 7131930 — our consultants will assist with compatibility, delivery and configuration details. Technical data Article number: VHL-500M GTIN: 4061905094019 Manufacturer: Vertex Facts Weight: 3.8 kg Arm reach: 220 x 220 mm Voltage: 110 V/220 V Halogen lamp: 12 V/50 W – 24 V/50 W Special features Light head: IP67 protection Articulated arm: IP65 protection Waterproof design, halogen or LED options Brand: Vertex FAQ What level of water and dust protection does the lamp offer? The VHL-500M features an IP67 light head and an IP65 arm, meaning the head resists temporary immersion while the arm is protected against dust and low-pressure water jets. Can the lamp be used with different mains supplies? Yes. The VHL-500M accepts 110 V/220 V mains voltages for compatibility with varied workshop electrical systems. Which lamp types are available and what are their specifications? The unit is offered with halogen or LED options; halogen variants are rated at 12 V/50 W to 24 V/50 W and are suited to contrast-critical tasks, while LED provides longer service life and reduced heat. Is the lamp suitable for precision inspection benches? Yes. The articulated arm and focused light output make the VHL-500M well suited to inspection benches, assembly stations and other tasks requiring controlled illumination. How heavy is the lamp and how does that affect installation? Weighing approximately 3.8 kg, the lamp offers a stable platform for bench or fixed installation without excessive mass for mounting supports. Manufacturer: Vertex Machinery Works Co., Ltd.; No. 296, Sec. 1, Feng Shih Road, Fengyuan District, Taichung City 420, Taiwan
Secure components with reliable workpiece clamps
Workpiece clamps, also known as workholding clamps or workholding devices, form the essential mechanical interface between machine and part in industrial fabrication. They keep components absolutely play-free, positionally accurate and vibration-resistant during milling, turning, drilling or grinding.
How workpiece clamps ensure process stability
A correctly specified clamping concept transfers the high cutting and feed forces of modern CNC machines into the machine table or spindle without deforming the part. The right combination of mechanical, hydraulic, pneumatic or magnetic solutions enables fast, repeatable setups and supports automated part change where required. Typical applications range from single-part turning to high-volume series milling and complex five-axis machining.
Concrete production benefits at a glance
- repeatable positioning: reduces scrap and rework
- high clamping forces: withstands aggressive cutting without part movement
- reduced set-up time: modular systems and quick-change features speed throughput
- improved surface finish: vibration damping for finer results and tighter tolerances
- flexible compatibility: vices, chucks, clamping plates and zero-point systems for diverse geometries
Why Metav's range is the practical choice
Metav combines decades of specialist know-how with a broad, handpicked range that democratises precision for workshops and industry alike. Based in Emmerich, Metav acts as a quality filter for the European market and supplies more than 250,000 products from precision metrology to complete workshop equipment. With the trust of over 48,000 customers, Metav offers a single-source approach that reduces supplier complexity and secures dependable delivery to your workbench.
Technical data
- function: mechanical interface between machine and workpiece
- primary requirements: absolute positional accuracy; vibration reduction; high clamping forces
- technologies: mechanical, hydraulic, pneumatic, magnetic
- typical components: machine vices; chucks; clamping plates; zero-point systems; pratzen; clamping jaws
- application areas: milling; turning; drilling; grinding; automated part change systems
- production benefits: reduced set-up time; enhanced process security; optimised series and single-part production
The practical summary
Workpiece clamps bring the stability and repeatability required to meet tight tolerances and excellent surface quality, making them indispensable across machining operations. Choosing the right workholding clamps and modular workholding devices is a decisive step towards higher productivity and consistent part quality.
FAQ
What types of workpiece clamps are suitable for automated machining?
Workholding clamps with quick-change modules, hydraulic actuation or magnetic systems are commonly used for automated machining. These workholding devices enable fast, repeatable part changes and integrate with zero-point systems.
How do workpiece clamps affect surface finish and tolerances?
A stable clamping concept minimises vibration and part movement; this improves surface finish and supports achieving narrow tolerances when using high-precision workpiece clamps or workholding devices.
Can the same workpiece clamps handle different part geometries?
Modular workholding clamps and adaptable clamping jaws allow flexible fixturing for varied geometries; combining vices, clamping plates and pratzen increases versatility on the shopfloor.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com