Precision boring bars with internal coolant for deep hole accuracy
Boring bars with internal coolant are precision tools designed to enlarge and finish existing holes, delivering tight dimensional and form tolerances while preventing tool breakage and surface damage; they are essential for deep bores and blind holes where external cooling cannot reach the cutting edge. These systems force high-pressure coolant through axial channels directly to the cutter, which reduces thermal stress and efficiently evacuates chips, making them ideal for machining difficult-to-cut or long-chipping materials. As a compact tool solution they combine rigidity, chip control and cooling to improve cycle times and extend tool life, with the main advantages being enhanced hole quality, repeatability and reduced rework for production and maintenance machining operations.
40mm S32T PWLNL Boring Bar PWLN for WNMG 0804, 32mm Shank Diameter 60mm Cutting Height, Left-Hand - Teknik Makina
Take advantage of the combination of robust build, precise compatibility with WNMG 0804 inserts and an optimised 95° cutting angle for consistent chip control; order directly via Metav Werkzeuge or consult the team for application-specific advice. Boring bar PWLN for WNMG indexable inserts (S32T PWLNL) by Teknik Makina — 32 mm shank, left‑hand The PWLN boring bar for WNMG indexable inserts delivers a left‑hand turning solution for internal and external machining where stable clamping and predictable chip flow matter most 32 mm shank diameter Compatible with WNMG 0804 inserts Left‑hand design for internal turning 95° cutting angle for reliable chip control Precision that raises throughput and reduces rework The bar is engineered to provide repeatable results under industrial conditions. Its 32 mm shank and ISO designation S32T PWLNL ensure stable mounting in standard tool holders, reducing vibration and the risk of tool chatter. The geometry, matched to WNMG 0804 indexable inserts, translates into consistent cutting engagement and predictable tool life; fewer interruptions for tool changes mean higher effective machine uptime and improved process economy. Easy integration and mechanical reliability on the lathe With a 300 mm overall length, 40 mm diameter and a cutting height of 60 mm, the bar fits typical turret and tool‑post set‑ups while keeping the centre‑of‑mass close to the holder. The left‑hand configuration and a 95° cutting angle support controlled chip evacuation and stable side cutting forces, which simplifies set‑up and reduces the need for frequent readjustment. The component’s mass (approx. 1.764 kg) contributes to damping without excessive inertia, helping to maintain surface finish and dimensional accuracy during extended cuts. Practical application advantages for workshop and production use Compatibility with WNMG 0804 inserts means fast indexable insert changes and broad grade options for different materials and cutting conditions. The holder’s design supports a wide range of turning tasks where left‑hand engagement is required, from finishing grooves to light roughing passes. As a standardised tool, it enables straightforward stock management and quick replacement in multi‑machine environments, supporting predictable scheduling and lower downtime. Contact Metav Werkzeuge for tailored advice on integrating this tool into production and to secure supply from Emmerich — phone +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: P372TM Brand: Teknik Makina Designation: PWLN for WNMG indexable inserts ISO designation: S32T PWLNL Dimensions / Core data Shank diameter: 32 mm Diameter: 40 mm Overall length: 300 mm Cutting height: 60 mm Cutting angle: 95° Weight: 1.764 kg Special features Compatible inserts: WNMG 0804 Cutting direction: left Clamping holder designation: 08 FAQ What insert size is required for this holder? The boring bar accepts WNMG 0804 indexable inserts; the holder geometry is matched to this insert size for correct seating and chip control. Is the tool suitable for left‑hand turning only? Yes — the bar is a left‑hand design and is intended for operations where left‑hand cutting is required. What is the ISO designation of the tool? The tool carries the ISO code S32T PWLNL, which defines the shank and holder style for standard tool posts. Can grades and coatings of inserts be varied for different materials? Different grades and coatings for WNMG 0804 inserts can be selected to suit specific materials and cutting speeds while using this holder. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm S32T PWLNR Boring Bar For WNMG 0804 Inserts 32mm Shank, 60mm Cutting Height, 95° Cutting Angle - Teknik Makina
Benefit from the robust S32T PWLNR design combined with compatibility for WNMG 0804 indexable inserts to secure stable turning and predictable tool life. Take advantage of the 32 mm shank and 300 mm overall length for deeper machining with reduced vibration — order via Metav Werkzeuge or consult the team for tailored application advice. Boring bar PWLN for WNMG indexable inserts (S32T PWLNR, 32 mm shank) by Teknik Makina The PWLN for WNMG indexable inserts is a right-hand boring bar engineered for secure turning with WNMG 0804 inserts in industrial and workshop turning applications S32T PWLNR design for stable clamping Compatible with WNMG 0804 indexable inserts 32 mm shank diameter for secure mounting 300 mm overall length for deep operations Stable clamping for consistent turning performance The S32T configuration delivers a compact, rigid toolholder geometry that promotes secure clamping and reduced chatter in interrupted cuts. With a 32 mm shank and the specified ISO designation, the holder provides standardised mounting that simplifies fixture selection and repeatability across setups. Using indexable inserts means only the cutting edge requires replacement, lowering downtime and enabling consistent component tolerances. Reach deeper with a balanced, vibration‑resistant design A 300 mm overall length combined with a 40 mm head diameter gives reach for deeper bores while maintaining a controlled mass distribution. The 95° cutting angle and a 60 mm cutting height support efficient chip control and stable engagement in right‑hand cuts. These dimensions make the tool suitable where extended reach is necessary without sacrificing surface finish or dimensional stability in the machined part. Simplified tool integration and predictable productivity Marked as S32T PWLNR, the bar fits common toolholders and complements workflows that rely on WNMG 0804 inserts. The standardised insert interface reduces setup complexity and enables quick insert changes to adapt to different materials and cutting conditions. The tool’s measured weight (approx. 1.764 kg) and nominal geometry aid in balancing considerations for spindle and turret operations, supporting steady cycle times. Practical guidance for selecting inserts and applications This boring bar accepts WNMG 0804 indexable inserts; the choice of insert grade and geometry determines cutting performance for specific materials and feeds. The right‑hand cutting direction aligns with standard lathe configurations. As the bar is a modular component, selecting an appropriate insert coating, grade and chipbreaker will tailor the combination to priorities such as tool life, surface finish or productivity without altering the holder. For secure, repeatable turning with a robust 32 mm shank and standard WNMG 0804 compatibility, contact Metav Werkzeuge for application guidance or to arrange procurement through Metav Werkzeuge GmbH in Emmerich Technical data SKU: P362TM Manufacturer: Teknik Makina Article designation: Boring bar PWLN for WNMG indexable inserts ISO designation: S32T PWLNR Facts Shank diameter: 32 mm Cutting height: 60 mm Overall length: 300 mm Head diameter: 40 mm Cutting angle: 95° Weight: 1.764 kg Cutting direction: right Special features Compatible with WNMG 0804 indexable inserts Right‑hand boring bar Clamping size: 08 FAQ What insert type does this boring bar accept? The boring bar accepts WNMG 0804 indexable inserts; the insert determines the cutting performance and material suitability. Is the bar suitable for deep bore operations? Yes. The 300 mm overall length and balanced geometry make the bar suitable for deeper turning operations while maintaining stability. What is the shank diameter and why does it matter? The shank diameter is 32 mm; a larger shank diameter improves clamping rigidity and reduces deflection during cutting. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm S32T SDQCL Bohr Bar For DC-- 11T3 Indexable Inserts, 107.5° Cutting Angle, 300mm - Teknik Makina
Benefit from a rigid 32 mm shank, compatibility with DC-- 11T3 indexable inserts and a precise 107.5° cutting angle for stable left‑hand boring; order the S32T SDQCL boring bar (K281TM) directly via Metav Werkzeuge or request advice from our consultants. S32T SDQCL Boring Bar (K281TM) — 32 mm Shank, 300 mm Length by Teknik Makina A S32T SDQCL boring bar engineered for left‑hand turning with DC-- 11T3 indexable inserts, suitable for medium‑duty CNC turning applications 32 mm sturdy shank for stable machining Compatible with DC-- 11T3 indexable inserts 300 mm overall length for deeper reach Left‑hand cutting orientation, 107.5° approach angle Reduced vibration and consistent surface finish through stiff mounting The boring bar is built around a 32 mm shank, providing increased rigidity that minimises deflection during moderate cantilever use. With a cutting height of 50 mm and a mass of 1.833 kg, the design balances stiffness and handling to deliver vibration‑reduced cuts and more consistent component geometry. Reduced chatter improves tool life and lowers rework rates, a tangible efficiency gain for production runs where repeatability matters. Fast indexable‑insert changes and predictable chip formation The tool is compatible with indexable inserts, specifically DC-- 11T3, allowing quick replacement without regrinding and therefore reduced downtime. The geometry, featuring a 107.5° cutting angle, is optimised for predictable chip flow and reliable edge engagement in left‑hand cutting operations. Indexable technology offers cost‑effective maintenance: worn inserts can be rotated or swapped in seconds, maintaining process stability across batches. Reach for deeper bores while retaining control An overall length of 300 mm and an outer diameter of 40 mm give the holder extended reach for internal operations and face bores where access is limited. The combination of length and a robust shank diameter helps maintain concentricity when working at depth; when longer reach is required, the tool’s dimensions make it suitable for setups that balance access and rigidity. This enables machining of stepped bores or operations where extended tool engagement is unavoidable. Reliable choice for workshop and small‑series production Manufactured by Teknik Makina, the holder is designed for routine use in workshops and small production cells where efficient insert changes and predictable performance are priorities. The left‑hand cutting orientation is advantageous for specific lathe setups and component orientations. Overall, the component is a pragmatic choice when a straightforward, serviceable indexable‑insert boring solution is needed, combining practical handling with stable cutting geometry. Contact Metav Werkzeuge for delivery options and technical advice on the Teknik Makina S32T SDQCL boring bar (K281TM) and to discuss compatibility with current CNC setups Technical Data SKU: K281TM Manufacturer: Teknik Makina ISO designation: S32T SDQCL English designation: SDQC for DC-- Indexable Inserts Dimensions & Weights Shank diameter: 32 mm Cutting height: 50 mm Overall length: 300 mm Diameter: 40 mm Weight: 1.833 kg Cutting angle: 107.5° Compatibility & Features Compatible inserts: DC-- 11T3 Cutting direction: left Clamp holder designation: 11 eClass: 21180806 FAQ What inserts fit this boring bar? The boring bar accepts DC-- 11T3 indexable inserts; the S32T SDQCL holder is machined to seat these inserts securely for predictable chip control. Is the cutting orientation left‑hand or right‑hand? This holder is manufactured for left‑hand cutting and is therefore suited to operations that require that orientation. What are the main dimensions to check for machine compatibility? Key dimensions are a 32 mm shank, 300 mm overall length and 40 mm body diameter; confirm these against the lathe’s tool post and overhang limits. Can this tool be used in small‑batch production? Yes, the S32T SDQCL’s use of indexable inserts and straightforward clamping makes it well suited to small‑series production where fast insert changes reduce downtime. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40mm S32T SDQCR Boring Bar For DC-- 11T3 Indexable Inserts, 107.5° Cutting Angle, 300mm Length - Teknik Makina
Take advantage of a rigid 32 mm shank and a long 300 mm overall length to improve stability and reach in deep boring operations; the SDQC clamping and compatibility with DC-- 11T3 indexable inserts reduce changeover time and support consistent surface quality. Order the tool directly via Metav Werkzeuge or contact their consultants for application advice. S32T SDQCR boring bar — SDQC clamping for DC-- 11T3 indexable inserts, 32 mm shank (Teknik Makina) The S32T SDQCR boring bar is a right-hand turning tool engineered for demanding lathe and CNC operations, combining a sturdy shank with an SDQC clamping interface to accept DC-- 11T3 indexable inserts for efficient insert changes and reliable chip control. 32 mm shank for rigid clamping Compatible with DC-- 11T3 indexable inserts 300 mm overall length for extended reach 107.5° cutting angle for stable cutting Stable machining through increased stiffness and predictable dynamics A substantial 32 mm shank diameter significantly raises bending resistance and reduces vibrational tendencies during deep cuts, which directly improves repeatable accuracy and surface finish. The tool’s 50 mm cutting-edge height contributes to a robust cutting head geometry that keeps the insert seated firmly in the SDQC clamp, decreasing the risk of chatter and the need for frequent rework. With a mass of 1.833 kg, the bar provides a balance between rigidity and manageable handling for setup and tool changes. Reduced downtime with standardised inserts and quick clamping The SDQC clamping arrangement is designed for efficient insert replacement and consistent seat positioning, making the bar ideal for production environments where throughput matters. Compatibility with DC-- 11T3 indexable inserts allows consolidation of insert stock across multiple toolholders, simplifying logistics and lowering inventory complexity. The right-hand cutting orientation matches common turning operations and keeps tooling layouts straightforward on the shop floor. Improved chip flow and cutting geometry for dependable material removal A 107.5° cutting angle yields predictable chip formation and deflection, supporting cleaner evacuation of chips from the cut and reducing thermal loading on the cutting edge. An outer diameter of 40 mm and the extended 300 mm overall length provide reach for internal and mid-depth turning while preserving sufficient rigidity near the cutting zone. These geometric choices help maintain cutting stability and enable consistent part tolerances under repeat production cycles. Practical integration and workshop benefits The ISO designation S32T SDQCR denotes a recognisable tool interface that eases replacement and cross-referencing in tooling lists. The bar’s design supports standard workshop workflows and can be deployed on conventional lathes and CNC turning centres without bespoke adapters. As a Teknik Makina product, the tool is intended to fit into established tool systems and to reduce set-up times through predictable mechanical interfaces and standard insert use. For reliable turning with a robust 32 mm shank and SDQC clamping, contact Metav Werkzeuge for tailored supply and technical guidance on integrating the Teknik Makina S32T SDQCR into existing production processes. Technical Data Article number: K152TM Manufacturer: Teknik Makina ISO designation: S32T SDQCR Facts Shank diameter: 32 mm Cutting-edge height: 50 mm Overall length: 300 mm Weight: 1.833 kg Cutting angle: 107.5° Outer diameter: 40 mm Cutting direction: Right-hand Special features SDQC clamping for DC-- 11T3 indexable inserts Compatible with DC-- 11T3 insert geometry Ideal for lathe and CNC turning applications FAQ Which inserts fit this boring bar? The bar accepts DC-- 11T3 indexable inserts; the SDQC clamping system secures the inserts for repeatable positioning. Is the S32T SDQCR suitable for right-hand turning only? Yes. The S32T SDQCR is specified for right-hand cutting and is optimised for conventional right-hand turning operations. What machine types is this tool designed for? The Teknik Makina boring bar is intended for use on lathes and CNC turning centres where extended reach and rigid clamping are required. How does the 107.5° cutting angle benefit machining? A 107.5° approach angle helps manage chip flow and reduces cutting forces at the insert edge, promoting consistent material removal and surface quality. Can the bar be integrated into existing tool inventories? The ISO-style S32T SDQCR interface and compatibility with standard DC-- 11T3 inserts simplify integration into common tooling systems. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm S32T SDUCL Drilling Bar 32mm Shank, 45mm Cutting Height, 93° Cutting Angle - Teknik Makina
Take advantage of a robust combination of stable mounting, precise indexable-insert compatibility and a compact overall length to maintain machining consistency. Order the S32T SDUCL directly via Metav Werkzeuge or consult the Metav team for application-specific recommendations. Teknik Makina S32T SDUCL boring bar – SDUC for DC-- indexable inserts, left-hand cut, shaft Ø 32 mm A S32T SDUCL boring bar engineered for internal boring operations with SDUC indexable inserts, suited to left-hand cutting applications in precision turning and machining centres Left-hand cutting orientation Shaft Ø 32 mm for rigid setup Overall length 300 mm for compact reach Compatible with DC-- 11T3 indexable inserts Increase process efficiency with a purpose-built insert holder The boring bar is configured to accept SDUC style indexable inserts, offering a reliable conversion of insert geometry into predictable internal finishes. Thanks to the shaft diameter 32 mm, the holder provides enhanced rigidity that reduces vibration and stabilises chip formation, which in turn improves tool life and repeatability. Integration of this insert-style approach allows economical blade replacement without the need to regrind solid tools, supporting lean tooling strategies in production environments. Precision compatibility that simplifies tool selection and setup Designed around a clear insert fitment, the tool guarantees compatibility with DC-- 11T3 inserts and presents a cutting angle 93° that balances radial engagement and cutting force direction. The cutting edge height 45 mm is matched to common insert geometries so that insert clamping and seat datum are consistent, reducing setup time and the risk of alignment errors. These traits make the holder suitable for workshops seeking repeatable internal bore results with straightforward insert logistics. Practical handling and installation for fast changeover With an overall length 300 mm and a measured mass of 1.833 kg, the holder offers a compact footprint while remaining easy to handle during tool changes. The left-hand cutting orientation is clearly indicated to ensure correct mounting and rotation direction on the lathe or machining centre. The combination of measured dimensions and the insert system delivers a serviceable balance between accessibility in tight bores and the rigidity needed for finishing passes, therefore helping to shorten non-productive time without sacrificing surface quality. Contact Metav Werkzeuge for tailored guidance on integrating the S32T SDUCL boring bar into existing tool inventories and to confirm the best DC-- 11T3 insert grades for specific materials Technical data SKU: K263TM ISO designation: S32T SDUCL Type: SDUC for DC-- Indexable Inserts Manufacturer: Teknik Makina Facts Shaft diameter: 32 mm Cutting edge height: 45 mm Overall length: 300 mm Weight: 1.833 kg Cutting angle: 93° Diameter: 40 mm Compatible inserts: DC-- 11T3 Cutting direction: left Special features Left-hand cutting orientation Designed for SDUC indexable inserts Compact overall length for confined bores Robust shaft for improved stability FAQ What insert type does the holder accept? The holder is designed for SDUC-style indexable inserts and is specifically compatible with the DC-- 11T3 insert form. Is the cutting direction left-hand or right-hand? This boring bar uses a left-hand cutting orientation; ensure spindle rotation and clamping match the left-hand specification. What are the key dimensions for machine set-up? Key measured values are shaft diameter 32 mm, overall length 300 mm, cutting edge height 45 mm, and a cutting angle of 93°, which assist in fixture and turret planning. Can the tool achieve high rigidity in small bores? The 32 mm shaft diameter combined with the insert clamping design provides an improved rigidity-to-length ratio suitable for finishing and semi-finishing internal operations. What is the product SKU for ordering and reference? Order reference is K263TM; use this SKU when specifying the Teknik Makina S32T SDUCL boring bar. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm S32T SDUCR Boring Bar For DC-- 11T3 Indexable Inserts, 93° Cutting Angle, 300mm Length - Teknik Makina
Combine robust ISO design, a 32 mm shank and a 300 mm overall length for improved rigidity and predictable chip control; order directly via Metav Werkzeuge or consult our specialists for application support. S32T SDUCR Boring Bar – 32 mm shank, for SDUC indexable inserts (Teknik Makina) A S32T SDUCR boring bar engineered for right-hand cutting with SDUC-style indexable inserts, intended for external boring and turning tasks where stability and quick insert changes are essential. 32 mm shank for stable machining Compatible with DC-- 11T3 inserts 300 mm overall length for deep reaches Right-hand cutting with 93° approach angle Improved rigidity for consistent surface quality The bar's 32 mm shank and calculated overhang deliver increased stiffness, reducing deflection during heavy cuts and improving surface finish. With a 300 mm overall length and a mass of 1.833 kg, the design balances reach and stability so that chatter is minimised when used in properly rated holders. Stiff toolholding translates into fewer scrapped parts and more predictable cycle times, because a rigid set-up keeps the cutting edge on the intended path and reduces flank wear. Fast indexable insert changes and reliable chip control Built for SDUC-style indexable inserts, specifically DC-- 11T3, the boring bar accepts quick, repeatable insert changes that lower tooling downtime. The 45 mm cutting height ensures a positive seat for the insert and consistent chip flow. Indexable inserts offer cost-effective regrinding and replacement compared with brazed tools; the modular approach supports both rapid maintenance and inventory control in production environments. Geometry tuned for efficient metal removal A 93° cutting angle produces an approach that spreads cutting forces and helps evacuate chips efficiently, which benefits both tool life and component integrity. The tool is configured for right-hand cutting, fitting standard lathe orientations and insert geometries without the need for special adapters. In practice, this geometry reduces radial loading and often enables higher feed rates on suitable workpiece materials when combined with correct speeds. Practical handling and application guidance Clamping provisions correspond to holder size 11, allowing secure fixation and repeatable runout performance; attention to correct torque and clean contact surfaces will preserve accuracy. When extended reach is necessary, consider the relationship between overhang and rigidity: a shorter overhang improves results, while the provided 300 mm length permits access to deeper features when required. Metav's supply chain supports consistent availability and a quality filter based in Emmerich for European customers seeking dependable metrology and tooling solutions. For reliable, precision boring with Teknik Makina components, contact Metav Werkzeuge in Emmerich for tailored advice and fast supply — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: K134TM Manufacturer: Teknik Makina ISO designation: S32T SDUCR Core technical data Shank diameter: 32 mm Cutting height: 45 mm Overall length: 300 mm Weight: 1.833 kg Diameter: 40 mm Cutting angle: 93° Cutting direction: right Special features For indexable inserts: DC-- 11T3 Compatible with SDUC indexable inserts Clamping holder designation: 11 Right-hand tool configuration FAQ Which inserts are compatible with this boring bar? This S32T SDUCR boring bar accepts SDUC-style indexable inserts, specifically the DC-- 11T3 format for secure seating and reliable chip control. Is the tool intended for right-hand cutting only? Yes — the bar is configured for right-hand cutting, matching common lathe orientations and insert geometries. What are the most important dimensions to consider when setting up? Key dimensions: shank diameter 32 mm, overall length 300 mm, cutting height 45 mm, and diameter 40 mm; overhang and holder rigidity will directly affect machining accuracy. Which holder size is required for safe clamping? The clamping provision corresponds to holder designation 11; use a holder that matches this specification and ensure proper torque for repeatable runout. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40mm S32T SDXCR Drill Bar 55mm Cutting Height 120° Cutting Angle, Right-Hand - Teknik Makina
Take advantage of a stable combination of rigidity and reach: the bar’s 32 mm shank and 300 mm overall length deliver low vibration and consistent surface finish in deep internal turning; order directly via Metav Werkzeuge or contact our consultants for tailored advice. S32T SDXCR Boring Bar — boring bar for DC-- 11T3 indexable inserts, right-hand, 32 mm shank The S32T SDXCR boring bar is a right-hand tool designed for precision internal turning and extended-reach boring with indexable inserts Right-hand cutting orientation Compatible with DC-- 11T3 inserts 32 mm shank diameter for secure clamping 300 mm overall length for extended reach Reliable performance for precision internal turning The bar is engineered to provide stable cutting in internal turning operations: the combination of a 32 mm shank and a balanced mass distribution reduces chatter, which in turn improves dimensional accuracy and surface finish. With a 120° cutting angle, chip evacuation is promoted and insert life is extended under typical finishing and semi-finishing conditions. This configuration supports efficient machining cycles and predictable process results in production and workshop environments. Secure clamping and extended reach reduce rework A secure clamping interface and the solid 32 mm shank provide enhanced rigidity compared with slimmer holders, meaning less flex during deep bores. The 300 mm overall length offers reach into recessed features without compromising stability, so fewer setup changes are required. Reduced vibration leads to longer insert life and lower scrap rates—an economic advantage that supports faster throughput in small to medium series production. Fast insert changes and simplified tooling logistics Designed for use with DC-- 11T3 indexable inserts, the bar accepts a widely available insert form factor for rapid replacement and consistent cutting edges. Indexable technology minimises downtime because inserts can be rotated or changed without regrinding; tooling management becomes simpler and inventory more predictable. The bar’s ISO designation S32T SDXCR aligns it with established tooling families, easing integration into existing toolholders and processes. Built for workshop reliability and predictable supply The construction and geometry focus on dependable, repeatable results in industrial and trade settings. The robust design supports conservative feeds and speeds where surface quality is paramount, while the right-hand cut direction matches standard lathe configurations. Paired with Metav’s supply and quality filter in Emmerich, the tooling solution aims to combine technical suitability with reliable availability for precision workshops. For Teknik Makina quality and rapid supply from Metav Werkzeuge, request expert advice or tailored delivery via info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application specifics and compatibility with existing tooling systems Technical data Article number: K474TM Brand: Teknik Makina ISO designation: S32T SDXCR Type: SDXCR for DC-- Indexable Inserts Cutting direction: Right Core dimensions Shank diameter: 32 mm Overall length: 300 mm Outer diameter: 40 mm Cutting height: 55 mm Cutting angle: 120° Weight: 1.833 kg Compatible insert: DC-- 11T3 Features Right-hand cutting orientation Compatible with DC-- 11T3 indexable inserts ISO series S32T SDXCR Long reach for deep internal turning FAQ What insert type suits this boring bar best? The bar is specified for DC-- 11T3 indexable inserts; this form factor fits the SDXCR pocket and permits fast insert changes. Is the bar suitable for deep internal boring? Yes — the 300 mm overall length and solid 32 mm shank provide the extended reach and rigidity required for many recessed bore operations. Which cutting direction does the tooling use? This holder is manufactured for right-hand cutting, matching standard lathe feed directions. How does the 120° cutting angle affect machining? A 120° cutting angle supports effective chip formation and distribution of cutting forces, which helps maintain surface quality during finishing passes. Can the bar be used with existing SDXCR tooling families? The ISO designation S32T SDXCR ensures compatibility with holders and clamping systems designed for this series and simplifies integration. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm S32T SVQBL Boring Bar SVQB For VBMT Inserts 50mm Cutting Height, Left-Hand - Teknik Makina
Take advantage of a rigid, ISO-classified tool that combines stable support and straightforward insert compatibility for efficient turning operations; the combination of a Ø32 mm shank, compatibility with VBMT 1604 inserts and a 300 mm overall length supports consistent cycle times. Order the K316TM directly via Metav Werkzeuge or consult the Metav team for application-specific setup and availability. Boring bar K316TM — SVQB for VBMT indexable inserts (left-hand, Ø40 mm) by Teknik Cutting Tools A Boring bar K316TM engineered to accept VBMT 1604 indexable inserts for robust turning tasks, offering stable geometry and ISO S32T SVQBL compatibility for workshop and production environments Left-hand cutting direction, 107.5° cutting angle Compatible with VBMT 1604 indexable inserts ISO S32T SVQBL designation with Ø32 mm shank 300 mm overall length, robust 1.79 kg weight Greater rigidity for repeatable turning quality The tool is built around a Ø32 mm shank that provides increased stiffness compared with smaller holders; this rigidity directly reduces deflection during interrupted cuts and contributes to a steadier surface finish. The 107.5° cutting angle is optimised to balance shear formation and chip control when paired with VBMT geometry, helping to maintain insert life. At 1.79 kg the assembly offers a robust feel without excessive mass, which aids stable spindle behaviour and predictable tool dynamics during cycle runs. Insert compatibility that speeds tool changes and reduces costs Acceptance of VBMT 1604 indexable inserts means rapid replacement and straightforward grade selection for varied workpiece materials. The ISO designation S32T SVQBL clarifies seat and mounting compatibility on modern toolposts, allowing straightforward cross-referencing with insert catalogs. Designed for left-hand cutting, this holder adapts to operations that require reverse cutting direction, while indexable inserts permit economical reuse of the carbide body by rotating or replacing only the cutting tips, supporting a favourable cost-per-part ratio. Practical dimensions to streamline setup and machine integration A 300 mm overall length and Ø40 mm body give a clear installation envelope for many lathe applications, easing reach into deeper bore operations while keeping vibration under control. The combination of measured geometry and standardised ISO interface simplifies tool changeover procedures, minimises downtime and supports consistent production flow. Supplied as a defined ISO holder, the design aligns with established workshop stocks and Metav’s logistics, ensuring reliable availability from the Emmerich quality hub. For tailored recommendations on the Teknik Cutting Tools K316TM or to arrange supply and delivery from Metav Werkzeuge in Emmerich, please contact Metav Werkzeuge for expert advice and availability. Technical data Article number: K316TM Brand: Teknik Makina Designation: SVQB for VBMT indexable inserts ISO designation: S32T SVQBL Numbers / Core technical data Shank diameter: 32 mm Overall length: 300 mm Body diameter: 40 mm Cutting height: 50 mm Cutting angle: 107.5° Weight: 1.79 kg Compatibility / Features Compatible inserts: VBMT 1604 Cutting direction: left ISO compatibility: S32T SVQBL SKU: K316TM FAQ Which insert size fits this tool? The K316TM boring bar by Teknik Cutting Tools is specified for VBMT 1604 indexable inserts, offering direct compatibility with that insert format. What are the main dimensions to consider for setup? The K316TM presents a Ø32 mm shank, Ø40 mm body diameter and a 300 mm overall length, which should be checked against turret clearance and holder reach. Is this tool suited for left-hand machining? Yes, the holder is configured for left-hand cutting and features a 107.5° cutting angle matched to VBMT cutting-edge geometries. What ISO designation identifies the holder type? The product is designated S32T SVQBL, enabling straightforward cross-reference to ISO holder standards and accessory lists. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm S32T SVQCL Boring Bar For VCMT 1604 Indexable Inserts 50mm Cutting Height, Left Hand - Teknik Makina
Take advantage of a rigid left‑hand boring bar with a 32 mm shank and 300 mm overall length for stable internal turning operations; the tool supports VCMT 1604 indexable inserts and combines precise geometry with robust clamping for consistent bore quality — available via Metav Werkzeuge or consult Metav’s specialists for technical guidance. K324TM S32T SVQCL Boring Bar (left‑hand) — for VCMT 1604 inserts, Ø32 mm shank K324TM S32T SVQCL is a left‑hand turning/boring bar designed for internal and facing operations with indexable inserts, optimised for workshop use and industrial turning centres Left‑hand cutting orientation Shank Ø 32 mm for high rigidity Compatible with VCMT 1604 inserts 300 mm overall length for deep reach Consistent bore quality through optimised rigidity The bar’s 32 mm shank and 300 mm overall length deliver a balance between reach and stiffness that reduces vibration during internal turning. Reduced chatter improves surface finish and extends insert life, which translates into lower tooling costs per part. The specified cutting angle of 107.5° helps control cutting forces in left‑hand operations, so the tool maintains concentricity in demanding bore and shoulder cuts. This mechanical stability is particularly beneficial in serial production, where repeatability and minimal rework are priorities. Insert compatibility and geometry that boost productivity Designed for VCMT 1604 indexable inserts, the holder accepts widely used carbide grades and geometries, enabling flexible process optimisation. The S32T SVQCL ISO designation indicates the shank and head configuration suitable for standard clamping systems; this simplifies toolholder selection at the machine and reduces setup time. With a cutting height of 50 mm and a head diameter of 40 mm, the geometry supports effective chip control and predictable cutting behaviour, helping to maintain cycle times and throughput. Workshop integration and safe handling for reliable use The tool’s weight of 1.786 kg and a clear left‑hand orientation make it straightforward to fit and check during tool changes. The explicit ISO designation and compatibility notes facilitate inventory management and spare‑part planning. For retrofit and replacement workflows, the bar’s conventional dimensions mean minimal adaptation of existing clamping systems; the listed clamp size (16) aligns with common holder fixtures. Practical handling and robust construction contribute to safer operation and steady machine performance across shifts. Contact Metav Werkzeuge today for tailored advice on Teknik Makina’s K324TM boring bar and to arrange reliable supply from our Emmerich warehouse Technical Data Article number: K324TM Product name: S32T SVQCL boring bar Brand: Teknik Makina Type designation: SVQC for VCMT indexable inserts ISO code: S32T SVQCL Core data Shank diameter: 32 mm Overall length: 300 mm Head diameter: 40 mm Cutting height: 50 mm Weight: 1.786 kg Cutting angle: 107.5° Special features Left‑hand cutting direction Suitable for VCMT 1604 inserts Clamp size: 16 Designed for internal turning and facing SKU: K324TM FAQ What insert type fits this boring bar? The boring bar is suited for VCMT 1604 indexable inserts; the S32T SVQCL configuration supports standard carbide VCMT geometries for general turning. Is the bar suitable for deep‑hole boring operations? With an overall length of 300 mm and a 32 mm shank, the K324TM offers reach for many internal machining tasks while maintaining sufficient rigidity for repeatable results. Which cutting direction does the tool support? The holder is configured for left‑hand cutting; the left‑hand orientation is specified in the S32T SVQCL code and in the product data. How does the cutting angle affect machining performance? The 107.5° cutting angle helps control cutting forces and chip flow in internal turning, improving tool life and surface finish when using the recommended inserts. What information is needed to replace an existing boring bar? Provide the SKU K324TM, the ISO code S32T SVQCL, and the clamp size (16) to ensure correct selection and compatibility with existing fixtures. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm S32T SVQCR Boring Bar For VCMT 1604 Indexable Inserts, 107.5° Cutting Angle, 50mm Insert Height - Teknik Makina
Take advantage of a rigid 32 mm shank and compatibility with VCMT 1604 inserts for stable external turning and predictable chip behaviour; the 300 mm overall length and right-hand cutting orientation ensure accessibility in standard lathes. Order via Metav Werkzeuge or consult the technical team for a tailored specification. S32T SVQCR Boring Bar — SVQC holder for VCMT 1604, Ø32 mm shank (Teknik Makina) A S32T SVQCR boring bar designed as an SVQC-style external turning holder for VCMT 1604 indexable inserts, optimised for right-hand cutting in conventional and CNC lathes Shank Ø32 mm for high rigidity Compatible with VCMT 1604 indexable inserts 300 mm overall length for extended reach Cutting angle 107.5° for reliable chip flow Stable, precision-focused design for external turning The holder is engineered to combine rigidity and accessibility: the shank diameter of 32 mm and the 300 mm overall length offer a balance between stiffness and reach that reduces chatter and improves surface finish on external turning tasks. The ISO-style designation S32T SVQCR identifies a solid shank SVQC configuration that accepts common triangular inserts; this familiar interface simplifies tool planning and inventory. With a defined cutting angle of 107.5°, the geometry supports controlled chip guidance, which translates into consistent cycle times and fewer reworks for series production. The design is suitable for machining typical external contours where insert indexability and repeatability matter. Reliable insert clamping and chip management for efficiency This SVQC holder is matched to VCMT 1604 inserts and provides a cutting height of 50 mm, ensuring the insert sits at the correct centre height for standard toolpost setups. The listed clamp size 16 indicates a robust clamping interface that secures the insert during interrupted cuts and medium-depth turning, reducing the risk of movement under load. Effective chip flow is supported by the holder's 107.5° approach, which helps direct chips away from the workpiece and toolface to maintain tool life and reduce manual chip clearing. These factors combine to lower downtime and improve throughput in batch and single-piece workflows. Practical workshop benefits and support from a trusted supplier With a listed weight of 1.786 kg, the holder is easy to handle during tool changes while remaining substantial enough to damp vibrations. The SVQC configuration and compatibility with widely used VCMT 1604 inserts make this tool holder a straightforward addition to an existing tooling set-up, reducing the need for special inserts. As a commercial partner, Metav provides logistical reliability from Emmerich and a broad range of complementary tooling; this supply-chain proximity supports predictable lead times and quality assurance across the tool range. For operations seeking dependable repeatability and less scrap, the combination of mechanical stability and standard insert compatibility delivers practical gains on the shop floor. For specification queries or to request a tailored cutting strategy with this Teknik Makina SVQC holder, contact Metav Werkzeuge GmbH in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone at +49 2822 7131930 for expert advice and purchasing support Technical data Article number: K224TM Manufacturer: Teknik Makina ISO designation: S32T SVQCR Product type: SVQC holder for VCMT indexable inserts Facts Shank diameter: 32 mm Cutting height: 50 mm Overall length: 300 mm Diameter: 40 mm Weight: 1.786 kg Cutting angle: 107.5° Cutting direction: right Suitable for inserts: VCMT 1604 Clamp holder size: 16 Special features SVQC-style indexable-insert holder Designed for external turning / boring operations Right-hand cutting orientation Compatible with standard VCMT 1604 inserts Brand: Teknik Makina SKU: K224TM FAQ Which inserts fit this holder? The holder is designed for VCMT 1604 indexable inserts; compatibility is confirmed for the SVQC clamping geometry used with this style of insert. Is this a right- or left-hand tool? This SVQC holder is specified for right-hand cutting, indicated by the product geometry and cutting direction data. What is the shank size and why does it matter? The 32 mm shank diameter gives the holder rigidity needed to reduce vibration and improve surface finish during external turning operations. Can the holder reach recessed areas on longer workpieces? With a 300 mm overall length, the tool provides added reach for many external turning tasks while maintaining acceptable stiffness for medium-depth cuts. How heavy is the tool and is it easy to handle during tool changes? The tool has a weight of 1.786 kg, offering a balance between robustness and manageable handling for routine tool changes. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm S32T SVUBR Boring Bar SVUB For VBMT Indexable Inserts 50mm Cutting Height, 93° Cutting Angle - Teknik Makina
Take advantage of a compact, rigid boring solution that combines straightforward insert replacement with reliable geometry for consistent bore finishes; the result is efficient tool changes and predictable cycle times. Order the tool directly via Metav Werkzeuge or consult the technical team for application-specific setup. S32T SVUBR boring bar — SVUB for VBMT indexable inserts by Teknik Makina, right-hand, Ø40 mm, 300 mm S32T SVUBR boring bar designed for precise internal turning and boring with VBMT indexable inserts, suitable for industrial CNC lathes and turning centres Right-hand cutting orientation Compatible with VBMT 1604 inserts Ø40 mm cutting diameter 300 mm overall length Stable insert system for predictable cycle times The S32T SVUBR boring bar is built around compatibility with VBMT 1604 indexable inserts, enabling rapid insert changes and predictable tool life management. The use of standard insert formats keeps spare-part logistics simple and reduces machine downtime, which improves overall process efficiency on the shop floor. The modular approach means companies can invest in a single holder and cover multiple bore sizes by stocking a small set of inserts, translating into lower inventory complexity and faster set-up times. Rigidity and geometry that support repeatable bore quality A shaft diameter of 32 mm combined with a nominal cutting diameter of Ø40 mm provides the stiffness required for accurate material removal in demanding turning operations. The specified cutting height 50 mm and the 93° cutting angle contribute to stable cutting forces and controlled chip formation, which reduces chatter and preserves tool life. The bar’s weight of 1.822 kg reflects a balanced construction that assists in vibration damping without excessive overhang, helping to maintain concentricity and surface finish across repeated cycles. Workshop integration and application benefits With an overall length of 300 mm and a right-hand cutting orientation, this bar integrates directly into common lathe toolposts and clamping systems; the clamp designation 16 allows straightforward mounting and secure fixing. The ISO designation S32T SVUBR simplifies procurement and documentation, ensuring compatibility with existing tool libraries and CAM setups. The design suits everyday industrial turning tasks where quick indexable insert changes, reliable repeatability and easy identification of tool geometry are priorities, supporting steady production throughput. For application advice or to confirm fitment for a specific machine, contact Metav Werkzeuge to discuss the Teknik Cutting Tools S32T SVUBR specification and arrange supply from Emmerich. Technical data SKU: K209TM ISO designation: S32T SVUBR Compatible inserts: VBMT 1604 Cutting direction: right Facts Shaft diameter: 32 mm Cutting height: 50 mm Overall length: 300 mm Cutting diameter: Ø40 mm Weight: 1.822 kg Cutting angle: 93° Special features Designed for VBMT indexable inserts Clamp designation: 16 Right-hand boring bar Brand: Teknik Makina FAQ What insert size fits this boring bar? The bar is specified for VBMT 1604 indexable inserts and will accept standard VBMT 1604 geometries for economical replacement and straightforward stock management. Is the cutting direction right-hand or left-hand? This model is a right-hand boring bar, indicated in the technical data and suitable for conventional right-hand turning operations. What are the key dimensions for planning tool set-up? Key dimensions include a shaft diameter of 32 mm, overall length 300 mm, cutting height 50 mm and cutting diameter Ø40 mm, which aid in fixture and collision planning. Can this bar be integrated into existing tooling systems? The S32T SVUBR carries a common ISO designation and a clamp designation of 16, facilitating integration with standard clamping units and lathe toolposts Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm S32T SVUCL Boring Bar 32mm Shank 50mm Cutting Height Left-Hand, 93° Angle - Teknik Makina
Benefit from the combination of rigid 32 mm shank and precise insert seating for VCMT 1604, which together deliver stable left-hand turning and consistent surface finish; order directly via Metav Werkzeuge or request specialist advice from our consultants. SVUC for VCMT Indexable Inserts – S32T SVUCL boring bar, 32 mm shank, left-hand The SVUC for VCMT Indexable Inserts is a left-hand boring bar designed for secure clamping of VCMT 1604 indexable inserts in external turning operations, offering extended reach and repeatable positioning. Left-hand cutting orientation 32 mm shank for rigid clamping For VCMT 1604 indexable inserts 300 mm overall length for extended reach Greater rigidity for consistent turning results The boring bar is engineered around a 32 mm shank, which increases stiffness at the toolholder interface and reduces vibration during cutting. This rigidity translates into improved surface finish and longer insert life, because the insert seating remains stable under cutting forces. The ISO designation S32T SVUCL indicates the standardised shank form and mounting geometry, which supports compatibility with a wide range of commercial toolholders. For workshops focused on predictable cycle times, the combination of shank size and secure clamping reduces rejects and rework. Clear fit and effective chip control with VCMT 1604 inserts Compatibility with VCMT 1604 indexable inserts means the toolholder accepts a commonly stocked insert form, keeping tooling costs and changeover times low. The geometry provides a cutting height of 50 mm and a 93° cutting angle, which together influence chip flow and radial engagement; the result is controlled chip evacuation and stable cutting when working on external diameters. As indexable inserts are replaced rather than re-sharpened, maintenance is quick and repeatable, supporting high uptime in production environments while preserving dimensional accuracy across batches. Practical handling and workshop integration With an overall length of 300 mm and a nominal tool diameter of 40 mm, the bar offers reach for deeper shoulders and extended external work while keeping balance suitable for rigid setups. The unit weighs 1.833 kg, which aids stable seating but still allows straightforward handling during insert changes. Left-hand orientation is matched to specific lathe feed directions; when combined with proper toolholder selection the arrangement minimises chatter and supports consistent tolerances. The design supports efficient workflows by simplifying insert indexing and repeatable clamping. Contact Metav Werkzeuge for tailored advice on Teknik Makina’s S32T SVUCL boring bar and ensure optimal toolholder selection from our Emmerich quality stock; email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: K306TM Manufacturer: Teknik Makina Product name: SVUC for VCMT Indexable Inserts ISO designation: S32T SVUCL Core dimensions Shank diameter: 32 mm Cutting height: 50 mm Overall length: 300 mm Diameter: 40 mm Weight: 1.833 kg Cutting angle: 93° Design & compatibility Compatible inserts: VCMT 1604 Cutting direction: left-hand Designation: SVUC for VCMT Indexable Inserts SKU: K306TM Manufacturer: Teknik Makina FAQ What inserts fit this boring bar? The SVUC for VCMT Indexable Inserts is designed specifically for VCMT 1604 indexable inserts, allowing straightforward replacement and standardised insert stock across the workshop. Is the bar suitable for deep external turning? The 300 mm overall length and 40 mm tool diameter make this boring bar suitable for extended reach external turning applications while maintaining sufficient rigidity for medium-duty cuts. What does left-hand cutting direction mean in practice? Left-hand cutting direction indicates the insert orientation and feed direction required on the lathe; the SVUC holder is intended for operations where the tool advances from the chuck towards the tailstock in a left-hand feed. How does the shank diameter affect performance? A 32 mm shank increases stiffness in the toolholder assembly, reducing vibration and helping to maintain surface finish and dimensional accuracy during cutting. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm S32T SVUCR Boring Bar SVUC for VCMT Indexable Inserts 50mm Cutting Height, 300mm Overall Length - Teknik Makina
Take advantage of a rigid, right-hand SVUC toolholder with a Shaft Ø 32 mm and compatibility with VCMT 1604 indexable inserts for efficient, repeatable internal machining — order directly via Metav Werkzeuge or consult our specialists for tailored support. Boring bar SVUC for VCMT indexable inserts — Teknik Makina, rigid toolholder with 32 mm shaft and 300 mm length Boring bar SVUC for VCMT indexable inserts offers a compact, purpose-built solution for internal turning and boring where stiffness and reliable insert seating are essential Right-hand cutting orientation Shaft Ø 32 mm for enhanced rigidity Compatible with VCMT 1604 inserts Overall length 300 mm for deep reach Increased stability for better surface finishes The S32T SVUCR configuration provides a stout, well-balanced holder that reduces chatter and improves concentricity during internal operations. With a Shaft Ø 32 mm and Overall length 300 mm, the assembly keeps deflection to a minimum so the toolholder transfers cutting forces efficiently into the machine. The listed weight 1.833 kg contributes to a predictable dynamic behaviour, which results in more consistent component tolerances and prolonged insert life. For workshops seeking measurable improvements in cycle-time reliability, the combination of shaft diameter and mass offers a clear advantage in rigidity over slimmer alternatives. Fast, economical machining with standard indexable inserts Engineered for use with VCMT 1604 indexable inserts, the toolholder accepts common insert sizes for quick changes and predictable cutting geometry. The cutting angle 93° and cutting edge height 50 mm ensure correct seating and alignment of the insert, reducing setup time and the risk of incorrect clamping. Using indexable inserts keeps consumable costs transparent and enables targeted selection of grades for specific operations. In practical terms, the design supports efficient material removal rates and repeatable surface quality while keeping tooling overhead low. Practical range and safe clamping for workshop use Designed for right-hand operations, the toolholder’s Right-hand cutting orientation and nominal diameter 40 mm shank offer compatibility with a wide range of toolposts and holders. The specified clamping interface (designation 16) facilitates secure fixation and simple set-up when pairing with standard clamping systems. The robust geometry simplifies alignment checks and reduces the need for frequent reworking. For production environments that value uptime, the holder’s straightforward configuration supports rapid insert replacement and predictable maintenance cycles, contributing to smooth shop-floor throughput. Speak to Metav Werkzeuge for specification advice on Teknik Makina boring bars and secure reliable supply from Emmerich — phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: K214TM ISO designation: S32T SVUCR Type: SVUC for VCMT indexable inserts Brand: Teknik Makina Facts Shaft diameter: 32 mm Shank/outer diameter: 40 mm Overall length: 300 mm Cutting edge height: 50 mm Cutting angle: 93° Weight: 1.833 kg Cutting direction: right Clamping designation: 16 Special features For VCMT 1604 indexable inserts S32T SVUCR configuration Right-hand orientation Robust, stiff construction Quick insert replacement FAQ Which inserts fit this boring bar? The boring bar is specified for VCMT 1604 indexable inserts; the geometry and seating are matched to that insert form for secure clamping and correct cutting height. Is the holder suitable for deep internal boring? With an Overall length 300 mm and Shaft Ø 32 mm, the holder is intended for deeper reach where increased rigidity is required compared with slimmer bars. What is the orientation of the cutting edge? The toolholder is configured for right-hand cutting, which should be selected according to the lathe or turning machine’s setup and the intended machining direction. How does the tool ensure insert alignment? The cutting edge height 50 mm and cutting angle 93° provide a defined seating plane and repeatable alignment for VCMT inserts, minimising set-up variation. What identifiers should be quoted when enquiring? Quote the SKU K214TM, the ISO designation S32T SVUCR, and the brand Teknik Makina to ensure precise correspondence. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm S32U CKUNR Boring Bar For KNUX 1604 Indexable Inserts, Right Hand 93° 350mm - Teknik Makina
Take advantage of a robust combination of rigidity, compatibility with KNUX 1604 indexable inserts and a compact 32 mm shank for reliable internal turning operations; order the tool via Metav Werkzeuge or consult our specialists for application advice. Boring bar S32U CKUNR (CKUNR for KNUX Indexable Inserts) — right‑hand, 32 mm shank, 350 mm overall length The boring bar S32U CKUNR is a right‑hand internal turning tool designed for use with KNUX 1604 indexable inserts, suitable for medium to heavy finishing operations on CNC lathes High rigidity 32 mm shank Compatible with KNUX 1604 inserts 350 mm overall length for deep bores Right‑hand cut direction Increased stability for accurate internal turning A solid design with a 32 mm shank and a mass of 2.264 kg reduces vibration and runout for more consistent bore diameters. The tool's geometry, including the cutting angle of 93°, improves insert support and chip flow, which together enhance surface finish and dimensional repeatability. For workshops aiming to reduce rework, the emphasis on mechanical stability translates directly into fewer rejects and shorter cycle‑time variance. Designed for fast insert changes and continuous production Compatibility with KNUX 1604 indexable inserts simplifies maintenance and minimises downtime: worn edges are replaced quickly rather than regrinded, improving throughput. The S32U CKUNR specification denotes a standard interface that integrates cleanly with common clamp systems, while the 52 mm cutting height and 40 mm nominal diameter provide a balance between cutting capacity and access in constrained bores. These features support efficient shift planning and predictable tool life. Practical fit for a range of machining tasks With a 350 mm overall length, this boring bar reaches deeper bores without compromising stiffness, making it suitable for internal finishing and light roughing on medium‑sized components. The right‑hand cutting direction suits conventional lathe setups and simplifies programming for automated sequences. As a result, production engineers find it easier to specify this bar where dependable, repeatable internal turning is required with indexable insert convenience. For tailored application advice or to confirm compatibility with existing holders, contact Metav Werkzeuge — Teknik Cutting Tools' RK754TM boring bar can be evaluated with our specialists via info@metav-werkzeuge.com or by phone at +49 2822 7131930, directly from Emmerich. Technical Data Article number: RK754TM Manufacturer: Teknik Cutting Tools / Teknik Makina Type designation: S32U CKUNR Description: CKUNR for KNUX Indexable Inserts Weight: 2.264 kg Data Shank diameter: 32 mm Cutting height: 52 mm Nominal diameter: 40 mm Overall length: 350 mm Cutting angle: 93° Special features Right‑hand cutting direction Compatible with KNUX 1604 indexable inserts ISO style S32U CKUNR Designed for internal turning and boring FAQ Which inserts fit this boring bar? The boring bar accepts KNUX 1604 indexable inserts; the CKUNR mounting form matches the insert pocket and clamp geometry used for that series. Is the bar suitable for deep‑bore applications? Yes, the 350 mm overall length of the RK754TM boring bar offers reach for deeper bores while retaining practical stiffness for finishing operations. What is the shank size and why does it matter? The tool has a 32 mm shank, which provides increased rigidity compared with smaller diameters and helps to reduce vibration and dimensional deviation in internal cuts. Can this bar be used for roughing as well as finishing? The design is appropriate for light roughing and finishing; pairing the bar with the correct KNUX grade insert allows adaptation to either higher material removal rates or superior surface quality. Which cutting direction does the tool use? This model is specified for right‑hand cutting, compatible with standard CNC lathe programmes and tool cycles. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
40mm S32U DCLNR Boring Bar For CN-- 1606 Indexable Inserts, 95° Cutting Angle, 350mm - Teknik Makina
Take advantage of the combination of rigid clamping, precise geometry and insert compatibility for dependable external turning operations; the 32 mm shank and compatibility with CN-- 1606 inserts ensure repeatable results. Order the boring bar directly via Metav Werkzeuge or consult the team for application advice. Bohrstange DCLN for CN-- Indexable Inserts — S32U DCLNR, 32 mm shank (Teknik Makina) The Bohrstange DCLN for CN-- Indexable Inserts is a right-hand external boring bar designed for turning operations that accept CN-- 1606 indexable inserts. Right-hand cutting for turning operations ISO designation S32U DCLNR 32 mm shank for rigid clamping Compatible with CN-- 1606 indexable inserts Stable, repeatable external turning with a rigid shank The boring bar is engineered to deliver consistent turning performance through a robust 32 mm shank that reduces deflection under load. With an overall length of 350 mm and a moderate weight of 2.272 kg, the tool balances accessibility with stability, supporting controlled cutting forces during external turning. This geometry is particularly beneficial when machining long workpieces or when aiming to maintain tolerance across multiple components, as the reduced vibration directly improves surface finish and dimensional repeatability. Secure clamping and reliable seating of inserts The tool’s S32U DCLNR ISO designation describes a secure shank-to-body interface and a cutter head geometry optimised for indexable inserts. The bar accepts CN-- 1606 plates and works with a clamp-holder reference of 16, which together provide positive insert retention and straightforward index changes. The clear-cut arrangement reduces setup time and minimises the risk of insert movement during interrupted cuts, resulting in fewer downtime interruptions and more predictable cycle times on production lathes. Geometry and cutting behaviour explained for process planners A 95° cutting angle and a 60 mm cutting height create a robust contact geometry that supports effective chip formation and controlled cutting loads on the insert edge. The right-hand cutting orientation suits conventional lathe arrangements and ensures predictable chip flow away from the operator and machine tool. These parameters translate into practical benefits: longer insert life where cutting conditions match the geometry, and easier process tuning when integrating the tool into existing turning cycles. Practical fit for workshop workflows and industrial production Designed as a production-ready turning tool, the bar combines a clear standard designation with simple insert compatibility to streamline inventory and tool management. The compatibility with widely used CN-- 1606 inserts simplifies procurement and reduces the number of unique spare parts required. For workshops aiming to centralise tooling without sacrificing performance, the bar offers a pragmatic balance between rigidity, accessibility and interchangeability that supports steady throughput and lower process variability. Contact Metav Werkzeuge for tailored application advice on the Teknik Makina boring bar S32U DCLNR (SKU K370TM) and secure reliable supply from our Emmerich hub Technical Data Article number: K370TM Manufacturer: Teknik Makina ISO designation: S32U DCLNR Product type: DCLN boring bar for indexable inserts Facts Shank diameter: 32 mm Cutting height: 60 mm Overall length: 350 mm Diameter: 40 mm Weight: 2.272 kg Cutting angle: 95° Cutting direction: right Special features Compatible with CN-- 1606 indexable inserts Clamp holder reference: 16 Right-hand external turning application Robust geometry for reduced deflection FAQ What type of inserts does this boring bar accept? The boring bar accepts CN-- 1606 indexable inserts; this compatibility simplifies insert sourcing and replacement during turning operations. Is the tool suitable for production lathes with standard holders? Yes, the S32U DCLNR designation and 32 mm shank make the bar compatible with common clamping systems; verify the holder size matches the shank and clamp reference. What is the cutting direction of the bar and what does this mean in practice? The bar is a right-hand cutting tool, which means the cutting action is produced when the workpiece rotates and the tool feeds from right to left in most conventional lathe setups. How does the 95° cutting angle affect machining? A 95° cutting angle gives a sturdy cutting geometry that supports good chip control and load distribution, which can extend insert life under appropriate cutting conditions. What is the SKU and manufacturer information for ordering? This item is listed as SKU K370TM and is manufactured by Teknik Makina; use the SKU to ensure precise ordering and stock checks. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm SIR S32T Boring Bar For 27 IR Indexable Inserts 60mm Cutting Height, Right-Hand - Teknik Makina
Take advantage of a rigid, purpose‑built boring solution that combines a Ø40 mm body, 32 mm shaft stiffness and compatibility with IR27 indexable inserts for consistent turning results — order directly via Metav Werkzeuge or consult the team for application advice. Boring bar SIR S32T (K347TM) by Teknik Makina — right‑hand, Ø40 mm, for IR indexable inserts A robust SIR for IR Indexable Inserts boring bar designed for right‑hand turning tasks in workshop and light industrial settings. Right‑hand cutting direction for conventional turning Compatible with IR27 indexable inserts Ø40 mm overall body for enhanced rigidity Shaft Ø32 mm and 250 mm overall length for stable machining Stable clamping and proven compatibility for indexable inserts The SIR S32T designation identifies a boring tool built specifically for use with IR27 indexable inserts, delivering quick insert changes and predictable cutting geometry. The clamping system uses an M5x18 Torx screw together with a TA065 support plate, secured with a T20 Torx key, which keeps the insert pocket fixed during engagement. For buyers seeking reproducible results, the combination of standardised insert seatings and secure fastening reduces setup variation and supports repeatable surface finishes in serial production. Rigidity and cutting engagement that improve process reliability A larger tool body of Ø40 mm combined with a 32 mm shaft increases stiffness at the toolholder, reducing vibration and deflection under load; this translates into more consistent bore tolerances and extended insert life. The 60 mm cutting height increases the contact area for IR inserts, allowing efficient metal removal in right‑hand operations without sacrificing stability. Such mechanical advantages reduce scrap rates and improve cycle stability, offering a measurable benefit where tight tolerances matter. Fast assembly, straightforward maintenance and dependable supply Assembly and maintenance follow common workshop practice: the insert is clamped with the supplied screw and Torx key and located on the TA065 plate for correct seating. The tool’s ISO designation and clear mechanical interfaces make it compatible with existing systems and spare‑part processes. Metav Werkzeuge supports availability and European distribution, ensuring a reliable parts supply and technical documentation when planning tool inventories or replacement cycles. Contact Metav Werkzeuge in Emmerich for stock availability, technical advice on Teknik Makina boring bars and application support — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: K347TM Manufacturer: Teknik Makina ISO designation: SIR S32T For indexable inserts: 27 IR U‑plate: TA065 Facts Diameter: 40 mm Shaft diameter: 32 mm Overall length: 250 mm Cutting height: 60 mm Weight: 1.523 kg Torx screw: M5x18 Torx key: T20 Special features Right‑hand cutting direction Clamping designation: IR27 Bezeichnung (English): SIR for IR Indexable Inserts SKU: K347TM Brand: Teknik Makina FAQ Which insert size is compatible with this boring bar? The tool accepts IR27 indexable inserts; the SIR S32T design ensures correct seating and clamping for those inserts. Is the cutting direction right‑hand or left‑hand? This boring bar is specified for right‑hand cutting operations. What are the key dimensions to check for toolholder compatibility? Relevant dimensions: Ø40 mm overall diameter, 32 mm shaft diameter and 250 mm overall length. How is the insert secured in the tool? Insert clamping uses an M5x18 Torx screw tightened with a T20 key and located on the TA065 plate for positive positioning. What is the ISO designation and SKU for ordering? ISO designation SIR S32T, SKU K347TM, manufactured by Teknik Makina. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
40mm Thread Milling Cutter For S14 S21 S30 S40 Indexable Inserts, S30 Compatible - Teknik Makina
Take advantage of a precision-oriented, versatile thread milling solution that combines compatibility with multiple insert sizes and robust toolholding for consistent cycle times; order the cutter directly via Metav Werkzeuge or contact our consultants for application support. DC216TM — Thread milling cutter Ø40 mm with indexable inserts (Teknik Makina) A DC216TM thread milling cutter for CNC metalworking, designed to accept indexable inserts for flexible thread production across a range of applications Thread milling cutter for indexable inserts S14–S40 40 mm nominal diameter for deep thread profiles 130 mm overall length, compact design 32 mm shank for secure holder clamping Faster thread production through adaptable insert compatibility The combination of indexable inserts compatibility and a sizeable cutting diameter means the tool is optimised for efficient cycle times in serial production. By accepting S14, S21, S30 and S40 insert sizes, the cutter reduces tooling changeover and inventory complexity, which translates into tangible productivity gains on CNC lathes and milling machines. This adaptability supports an improved cost-benefit ratio for workshops that need to switch between metric and imperial thread forms or varying material families without stocking multiple dedicated thread cutters. Secure clamping and dimensional stability for repeatable accuracy A robust 32 mm shank and a 130 mm overall length deliver stable toolholding, reducing chatter and preserving thread form during interrupted cuts. Stable clamping minimises run-out and contributes directly to repeatable surface finish and tolerance compliance in threaded components. For users not specialised in toolholder selection, the tool’s standard shank allows straightforward integration into common holders, ensuring the thread profile is produced consistently across batches and lowering scrap risk from poor fixation. Practical maintenance and quick indexable insert changes The cutter design uses standard fastenings (Torx M5x12 screws tightened with a T20 key) which simplifies insert replacement and maintenance routines. Quick insert changes shorten downtime and let production teams maintain throughput without specialised tooling for the changeover. Clear mechanical fixings also support reproducible clamping torque, which helps maintain insert seating and tool life; this delivers operational confidence and reduces the frequency of unscheduled interventions. Application range and recommended use cases With a nominal diameter of Ø40 mm, this thread mill is suited to medium-to-large threaded features in components manufactured from steels and common alloys where indexable inserts provide economic advantages. The tool serves job shops and manufacturers seeking scalable threading solutions that can adapt to various thread sizes by swapping insert types, ensuring versatility for wearing parts, housings and mechanical assemblies. When paired with appropriate feeds and speeds on CNC platforms, the cutter provides a balance of material removal rate and thread accuracy that supports both prototyping and series production. For tailored technical advice on the Teknik Makina DC216TM thread milling cutter and to discuss suitable inserts or holder options, contact Metav Werkzeuge for personalised support from Emmerich. Technical data Article number: DC216TM Name: Thread milling cutter For indexable inserts: for S14, S21, S30 and S40 Indexable Inserts Manufacturer: Teknik Makina Core data Diameter: 40 mm Overall length: 130 mm Shank diameter: 32 mm Torx screw: M5x12 Torx key: T20 SKU: DC216TM Special features Compatible insert types: S14, S21, S30, S40 Designed for CNC thread milling Robust shank for secure clamping Quick-change insert fastening (Torx) FAQ What insert sizes are compatible with this cutter? The DC216TM accepts indexable inserts in sizes S14, S21, S30 and S40, enabling quick adaptation to different thread forms and production needs. What diameter and overall length does the tool feature? The thread milling cutter has a nominal diameter of 40 mm and an overall length of 130 mm, suited to medium-to-large threaded features. Which clamping and fastening standards are used for insert changes? Insert clamping uses Torx M5x12 screws with a T20 key, allowing secure and repeatable insert replacement on the DC216TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
41mm Boring Bar for VER27 Indexable Inserts L300mm, 32mm Shank - Teknik Makina
Take the robustness of a 41 mm tool body together with a 32 mm shank and 300 mm overall length to maintain stable boring cycles and reduced vibration; the compatibility with VER27 indexable inserts ensures fast replacement of cutting edges and predictable runtime. Order the K345-5TM via Metav Werkzeuge or consult our advisers for application-specific setup. Boring bar K345-5TM — 41 mm, L 300 mm (Teknik Makina) Boring bar K345-5TM for secure machining with VER27 indexable inserts, designed for medium-deep boring tasks and stable toolholding 41 mm diameter body for rigidity Compatible with VER27 indexable inserts 300 mm overall length for extended reach 32 mm shank diameter for firm clamping Stable cutting performance for consistent cycle times The solid design provides a rigid toolbody that reduces chatter and maintains concentricity throughout the cut. With a 41 mm diameter and an overall length of 300 mm, the bar is engineered to deliver predictable results in repetitive operations; this stability translates directly into reduced rework and improved part quality. The use of VER27 indexable inserts means cutting edges can be exchanged without regrinding, which keeps spindle downtime to a minimum and supports continuous production. Fast set-up and secure clamping to save machine time Clamping is simplified by the 32 mm shank and a dedicated clamping area, with the top insert clamping width at 25 mm ensuring the cutting head sits firmly. The required Torx T20 connection standardises the tightening procedure and shortens tool changes. These design choices result in shorter set-up times on the machine and more predictable tool life, aiding shop-floor scheduling and increasing throughput. Compatibility with established insert systems reduces inventory complexity and speeds maintenance. Workshop-ready construction and practical handling Weighing 1.95 kg, the bar balances mass and handling for both manual and automated tool changes. The geometry supports insertion of VER27 indexable inserts and is identified under K345-5TM, making reordering straightforward. The tool is produced by Teknik Makina to machining-oriented tolerances suitable for production environments; documentation and SKU labelling support traceability and inventory control. For operations requiring extended reach and reliable repeatability, this bar provides a robust platform for efficient boring cycles. Contact Metav Werkzeuge for bespoke machining advice and to secure the K345-5TM 41 mm boring bar from Teknik Cutting Tools; phone +49 2822 7131930 or eMail info@metav-werkzeuge.com for prompt assistance and dispatch from Emmerich Technical data Article number: K345-5TM Product type: Boring bar Brand: Teknik Makina Core data Diameter: 41 mm Overall length: 300 mm Shank diameter: 32 mm Clamp/head width: 25 mm Weight: 1.95 kg Special features Compatibility: VER27 indexable inserts Torx key: T20 Label: 41mm boring bar VER27 L300mm Category: Bohrstangen / Boring bars FAQ Which insert type fits this boring bar? This boring bar accepts VER27 indexable inserts; the K345-5TM is configured for that insert family and straightforward edge replacement. What are the main dimensions to check for holder compatibility? Key dimensions are 41 mm body diameter, 32 mm shank diameter and 300 mm overall length for reach and clamping planning. Which toolholder or collet is required for the shank? The 32 mm shank requires a holder compatible with a 32 mm shank diameter and a clamping system able to secure the bar for boring operations. What fastener is used for the insert clamping? Insert clamping uses a Torx T20 interface; ensure the correct bit is available for secure tightening. How is the product identified for reordering? Reorder by SKU K345-5TM, labelled as a 41 mm boring bar for VER27 inserts and supplied by Teknik Makina. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
45mm Drill Bar STI For IR/ER Indexable Inserts 40mm Shank 300mm Overall Length, Right-Hand - Teknik Makina
Take advantage of a rigid, indexable-insert solution that combines 45 mm cutting diameter and a 40 mm shank for stable drilling and fewer tool changes; order directly via Metav Werkzeuge or consult our technical team for application advice. Drill bar S40T STIR (STI for IR/ER Indexable Inserts) – 45 mm diameter, 300 mm overall length (Teknik Makina) The S40T STIR drill bar is a right-hand indexable-insert holder engineered for IR/ER 22 inserts, intended for precision hole-making and production drilling in workshop and industrial environments *For IR/ER 22 indexable inserts *45 mm cutting diameter *300 mm overall length, 40 mm shank *Right-hand orientation, robust 60 mm cutting height Reliable indexable-insert performance for production drilling The S40T STIR is designed to accept IR/ER 22 indexable inserts, providing a practical balance between cutting capacity and tool economy. Using indexable inserts reduces downtime for resharpening and keeps inventory manageable while maintaining consistent hole quality. The 45 mm cutting diameter and 60 mm cutting height allow for stable engagement in through-holes and interrupted cuts, and the right-hand configuration matches standard spindle rotations in most machining centres. This configuration translates to measurable improvements in cycle stability and fewer unscheduled tool changes, supporting higher throughput in repetitive drilling tasks. Stiff shank design that improves hole accuracy A solid 40 mm shank delivers rigidity where it matters: at the tool-to-spindle interface. Increased rigidity minimises deflection under load, which directly benefits positional accuracy and surface finish in bores. The 300 mm overall length gives reach without excessive overhang, reducing vibration risk in deep-hole applications. For workshops without specialist toolholders, the standard shank diameter simplifies mounting and promotes repeatable clamping values, which means fewer scrap parts and faster setup times on the shopfloor. Compatibility and operational clarity for engineers and buyers Compatibility with the common 22 IR insert size simplifies tooling decisions across milling and turning centres; the holder’s ISO designation S40T STIR clarifies its role in established tooling systems. Specifying a single holder type for a range of components reduces tool-change complexity and allows production planners to forecast insert consumption more accurately. The indexable-insert approach preserves cutting-edge geometry without altering the holder, so maintenance is limited to insert replacement rather than complete tool refurbishment, lowering total lifecycle effort. Robustness and workshop suitability With a mass of 2.831 kg, the holder indicates substantial build quality while remaining manageable for manual handling during tool changes. Its construction is optimised for frequent use in industrial environments rather than occasional hobby tasks; the rigidity and geometry balance sustained cutting forces and thermal loads to maintain consistent performance. For operations requiring dependable repeatability and simplified inventory, this indexable-insert drill bar offers a pragmatic solution that supports workflow continuity and reduces the need for multiple specialist tools. For tailored application advice or to secure reliable delivery from Emmerich, contact Metav Werkzeuge for a consultation on integrating the S40T STIR into existing processes—email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: K360-1TM Manufacturer: Teknik Makina ISO designation: S40T STIR Numbers / Core Technical Data Cutting diameter: 45 mm Shank diameter: 40 mm Overall length: 300 mm Cutting height: 60 mm Weight: 2.831 kg Cutting direction: right Designs / Special features STI for IR/ER indexable inserts Compatible with 22 IR indexable inserts Right-hand orientation SKU: K360-1TM FAQ Which insert type fits this holder? The holder is compatible with IR/ER 22 indexable inserts; the S40T STIR accepts STI-style insert seats designed for that insert size. What are the key dimensions to check for toolholder compatibility? Check the 45 mm cutting diameter, 40 mm shank diameter and 300 mm overall length to ensure correct clearance and clamping in the machine spindle and toolholder. Is the shank size suitable for standard toolholders? The 40 mm shank is a common industrial size that fits many conventional toolholder systems and ensures a rigid connection for improved bore accuracy. Can this holder be used for interrupted cuts or tough materials? The geometry and 60 mm cutting height support interrupted cuts, while indexable inserts can be selected specifically for tougher materials; insert specification should match the intended workpiece. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
45mm SIL S40T Boring Bar For 16 ER Indexable Inserts, 40mm Shank × 300mm - Teknik Makina
Take advantage of a rigid 40 mm shank and a substantial 60 mm cutting height for stable, heavy‑duty internal turning; the SIL S40T design ensures reliable compatibility with 16 ER indexable inserts and fast changeovers. Order the tool via Metav Werkzeuge or consult Metav's specialists for application advice. Boring bar SIL S40T by Teknik Cutting Tools — 40 mm shank, left‑hand A SIL S40T boring bar designed for left‑hand internal turning with 16 ER indexable inserts, suitable for CNC lathes and precision workshop applications SIL S40T design for 16 ER inserts 40 mm shank for rigid clamping 60 mm cutting height for deep cuts Left‑hand cutting direction Stable clamping for improved surface finish and tool life The combination of a 40 mm shank and a robust construction delivers reduced vibration and greater rigidity during internal turning, which directly benefits surface finish and cutter life. With a 300 mm overall length and a mass of 2.839 kg, this tool balances reach and stability for medium‑depth boring operations. Operators and process planners will notice fewer reworks and more consistent cycle times when a rigid bar is used instead of undersized alternatives. Fast insert changes and predictable cutting performance Engineered specifically for 16 ER indexable inserts, the SIL geometry simplifies insert seating and repeatability, shortening downtime at tool change. The 60 mm cutting height provides a deep, secure insert pocket for heavy cuts and chip control, enabling efficient material removal rates without compromising safety. This configuration supports standard ER16 clamping arrangements and integrates smoothly into existing toolholding systems. Left‑hand orientation for tailored turning strategies A left‑hand cutting direction suits specific machining setups and complements toolpaths where reverse orientation improves chip flow or access. The left feed orientation, combined with the tool’s geometry, allows reliable engagement in internal boring tasks on CNC lathes and turning centres. The design is particularly useful when machining features that require a left‑hand approach to meet fixture or lathe‑axis constraints. Order the Teknik Cutting Tools SIL S40T boring bar (SKU K333TM) through Metav Werkzeuge for reliable supply and application guidance — Metav's specialists are available at info@metav-werkzeuge.com or +49 2822 7131930 to discuss machine compatibility and setup Technical data Article number: K333TM Manufacturer: Teknik Cutting Tools Model designation: SIL S40T Description: SIL for 16-22ER Indexable Inserts Dimensions & mass Shank diameter: 40 mm Diameter: 45 mm Cutting height: 60 mm Overall length: 300 mm Weight: 2.839 kg Cutting direction: left Compatibility & features Compatible inserts: 16 ER Collet/holder designation: ER16 Suitable for indexable insert boring For CNC/lathes internal turning FAQ Which indexable inserts fit this tool? The SIL S40T boring bar from Teknik Cutting Tools is specified for 16 ER indexable inserts and is designed to accommodate the seating and clamping geometry typical for that size. What are the key mounting dimensions? Relevant dimensions are a 40 mm shank diameter, 45 mm diameter, 300 mm overall length and 60 mm cutting height, which determine clamping and reach requirements for the machine setup. Is the cutting direction important for setup? Yes; the tool is manufactured for left‑hand cutting and should be used in operations and toolpaths that call for left‑hand engagement to ensure correct chip evacuation and cutting forces. Which toolholders are compatible? The bar is compatible with ER16 clamping systems and integrates into standard ER16 collet holders and corresponding tool posts on lathes and machining centres. Can the tool be used on CNC lathes for medium‑duty production? Yes; the SIL S40T boring bar is built for CNC and lathe internal turning in production environments where a rigid shank and reliable insert seating are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
48mm SIR S40T Boring Bar For 27 IR Indexable Inserts, 60mm Cutting Height, Right-Hand - Teknik Makina
Take advantage of the combination of stable cutting performance, broad IR27 insert compatibility and an extended reach for consistent turning results; order the K347-1TM directly via Metav Werkzeuge or consult the specialists for application advice. K347-1TM boring bar (SIR S40T) — 48 mm Ø, 300 mm overall length by Teknik Makina A K347-1TM boring bar engineered for right-hand turning with SIR clamping for IR indexable inserts, ideal for medium-duty lathe and turning-centre applications. SIR clamping for IR27 indexable inserts 48 mm outer diameter for stable cutting 300 mm overall length for extended reach Right-hand cutting orientation for standard lathes Engineered stability for consistent material removal The bar delivers stable performance by combining a substantial 48 mm outer diameter with a robust shank, reducing vibration during cutting. This geometry is particularly effective when machining interrupted cuts or harder materials where chatter compromises surface finish. The resulting process reliability helps to maintain dimensional tolerances over longer runs, supporting predictable cycle times and reduced scrap rates. Secure clamping and wide insert compatibility A SIR clamping system provides straightforward insert retention and repeatable seat location, optimised for IR27 inserts to ensure secure engagement and predictable cutting geometry. The clamping arrangement, combined with the specified Torx T20 drive and M5x18 fastening, allows efficient insert changes and reliable torque transmission, which benefits both tool life and operator safety in repetitive tool swaps. Practical design for workshop productivity and serviceability With a 300 mm overall length and a 40 mm shank diameter, the bar balances reach and rigidity for access into deeper workpieces without sacrificing stability. The modular nature of the clamping plate (U‑plate TA065) simplifies maintenance and reduces downtime; spare parts such as the clamping screw and plate are standardised, enabling fast replacement. The compact, service-friendly layout supports fleet standardisation on turning centres and manual lathes alike. Contact Metav Werkzeuge for availability, technical matching and local delivery of the K347-1TM boring bar; phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: K347-1TM Name: Boring bar (SIR for IR indexable inserts) Manufacturer: Teknik Makina Dimensions & weight Outer diameter: 48 mm Shank diameter: 40 mm Overall length: 300 mm Cutting height: 60 mm Weight: 2.89 kg Features & compatibility SIR clamping for IR indexable inserts Compatible with 27 IR inserts Clamping holder designation: IR27 ISO designation: SIR S40T Cutting direction: right Torx key: T20 Torx screw: M5x18 U‑plate: TA065 FAQ Which inserts are compatible with this boring bar? The K347-1TM boring bar is designed for IR27 indexable inserts and uses a SIR clamping system to secure the insert reliably. Is the cutting direction right-hand or left-hand? This tool is specified for right-hand cutting, suitable for standard lathe and turning-centre orientations. What are the key dimensions for machine setup? Key setup data: 48 mm outer diameter, 40 mm shank diameter and 300 mm overall length for the K347-1TM boring bar. How is the insert secured to the bar? Insert retention is achieved via the SIR clamping mechanism with a Torx T20 fastener and M5x18 screw paired with the TA065 clamping plate. Can this bar be used for extended-reach turning tasks? Yes, the 300 mm overall length provides extended reach while the robust diameter maintains cutting stability for deeper turning operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
48mm Thread Milling Cutter for S12 S14 S21 S30 S40 Indexable Inserts, 153mm Overall Length - Teknik Makina
Benefit from the combination of robust indexable‑insert compatibility and rigid mounting geometry: a 48 mm cutting diameter paired with a 40 mm shank and a 153 mm overall length delivers stable thread forms and predictable cycle times. The Torx fixing (M5x18, T20) reduces set‑up effort. Order the tool directly via Metav Werkzeuge or consult the technical team for process integration. Thread milling cutter DC209TM — for S12, S14, S21, S30 and S40 indexable inserts, Ø 48 mm (Teknik Makina) A Thread milling cutter DC209TM engineered for industrial thread milling tasks, compatible with a range of indexable inserts and built for repeatable performance in production environments Thread mill for S12–S40 indexable inserts Ø 48 mm cutting diameter 40 mm shank for rigid mounting Torx fixing M5x18 with T20 key Stable geometry for consistent thread quality The cutter’s construction focuses on stable geometry to maintain thread accuracy across serial production. With a 48 mm nominal cutting diameter and a 153 mm overall length, the design balances reach with rigidity, reducing vibration and improving surface finish. This stability supports predictable tool life and lowers the risk of premature insert wear, which in turn benefits process reliability and scrap reduction in small‑batch and series production. Fast insert changes to reduce downtime Quick and secure insert replacement is enabled by the Torx fixing system: M5x18 screws tightened with a T20 key. The use of standardised indexable inserts for S12, S14, S21, S30 and S40 formats permits straightforward stocking of spare tips and rapid re‑turn to cut. The result is reduced set‑up time and easier maintenance planning, which helps keep machining cells productive and simplifies shift handovers in multi‑operator environments. Engineered for production reliability A 40 mm shank enables a rigid clamping interface in appropriate holders, supporting repeatability and stable axial load transfer during thread milling cycles. The cutter’s proportions are chosen to suit workshop toolholders while preserving the cutting geometry required for consistent thread form generation. The robust mounting contributes directly to surface quality and tool life, supporting predictable machining costs and fewer process interventions. Practical handling and application notes The tool is intended for conventional thread milling operations using indexable inserts; the modular approach allows different insert grades to be chosen for specific workpiece materials and cutting conditions. The 40 mm shank provides secure locking in compatible toolholders, and the Torx screw arrangement simplifies routine checks. Where insert grade selection or holder compatibility requires clarification, refer to the machining strategy or consult technical advice to match cutting data with production demands. Contact Metav Werkzeuge for supply and machining advice on the Teknik Makina DC209TM thread milling cutter; email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific setups Technical Data Article number: DC209TM Manufacturer: Teknik Makina eClass: 21180805 ETIM: EC011860 Core measurements Diameter: 48 mm Overall length: 153 mm Shank diameter (Ø): 40 mm Torx screw: M5x18 Torx key: T20 Compatibility & features For S12, S14, S21, S30 and S40 indexable inserts Tool type: Thread milling cutter SKU: DC209TM FAQ Which insert sizes are compatible with this cutter? The cutter is compatible with S12, S14, S21, S30 and S40 indexable inserts; the article DC209TM accepts these standard insert formats for flexible grade and geometry selection. How is the insert secured to the cutter body? Inserts are fixed with an M5x18 Torx screw and tightened using a T20 key, providing a secure and easily serviceable connection. What are the key dimensions to check when mounting? Ensure a holder suitable for a 40 mm shank diameter and sufficient clamp length for the 153 mm overall length; these dimensions are central to achieving the cutter’s designed rigidity. Is the cutter suitable for serial production? Yes; the DC209TM is designed with a rigid shank and stable cutting geometry to support repeatable thread milling in production environments. What should be considered when selecting inserts for different materials? Insert grade and coating should be matched to workpiece material and cutting conditions; the DC209TM accepts standard S‑series inserts so grades can be selected to optimise performance and tool life. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
48mm Thread Milling Cutter for S21 S30 S40 Indexable Inserts, 210mm Overall Length - Teknik Makina
Take advantage of precise thread milling, secure clamping and simple insert compatibility for reliable production runs; benefit from the combination of a Ø48 mm cutting diameter, a 40 mm shank and robust Torx fastening — order the tool directly via Metav Werkzeuge or consult the application specialists for tailored advice. Thread milling cutter DC213TM — Ø48 mm, 40 mm shank, for S21, S30 and S40 indexable inserts (Teknik Makina) A Thread milling cutter DC213TM designed for efficient thread generation in CNC operations, compatible with S21, S30 and S40 indexable inserts and engineered for stable clamping and predictable tool life. Precision Ø48 mm thread diameter 40 mm shank for stable clamping Compatible with S21, S30, S40 inserts Torx M5x18 fastening with T20 key Faster, more economical thread production with indexable inserts Thread milling with indexable tooling reduces component rejects and lowers per-thread cost by allowing individual cutting edges to be replaced. The combination of an indexable insert system and the tool’s geometry supports repeatable thread milling cycles on modern CNC lathes and milling centres. Because inserts for different thread profiles can be selected independently, this solution is suitable for mixed production where flexibility and predictable consumable costs matter. The result is a measurable improvement in process efficiency while maintaining component quality. Stable machining through a robust interface and diameter control A consistent clamping interface is essential when producing threads to tolerance. The DC213TM offers a shank Ø 40 mm that provides secure attachment in standard toolholders, reducing run-out and vibration. With a Ø48 mm cutting diameter the tool maintains centreline stability during entry and exit, which helps to preserve flank form and surface finish. This mechanical reliability translates into fewer reworks and longer uninterrupted machining cycles — a decisive advantage in serial production. Quick, repeatable insert retention minimises downtime Tool change and maintenance time are cut by using a single Torx M5x18 screw for insert retention, tightened with a T20 key. The straightforward fastening method simplifies workshop routines, shortens downtime during insert changes and reduces the risk of incorrect assembly. Clear mechanical interfaces and standardised fastenings also make it easier to document maintenance intervals in machine schedules, supporting predictable uptime and easier spare-part planning. Designed for integration into CNC workflows and robust shop floors With an overall length of 210 mm, the tool provides the reach required for many turret and milling spindle set-ups while still offering the rigidity needed for consistent thread form. As a product from Teknik Makina, the cutter is conceived for professional environments where compatibility with S21, S30 and S40 indexable inserts is a central requirement. The construction supports inline process control and is suitable for workshops seeking to centralise tool inventories without sacrificing the ability to adapt to varied thread profiles. Contact Metav Werkzeuge for application-specific guidance on the DC213TM and for help selecting the correct insert grade and clamping arrangement to match production requirements — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: DC213TM Manufacturer: Teknik Makina Product type: Thread milling cutter Facts Diameter: 48 mm Overall length: 210 mm Shank diameter: 40 mm Torx screw: M5x18 Torx key: T20 Special features For S21, S30 and S40 indexable inserts Indexable insert fastening system Compact overall length for turret/spindle use Standard Torx retention for quick insert changes FAQ What insert types fit this cutter? The cutter is compatible with S21, S30 and S40 indexable inserts as specified for flexible thread machining. Is the shank size suitable for standard toolholders? Yes, the tool has a 40 mm shank diameter designed for standard clamping systems to ensure stable retention. Which fastening is used for the insert? Insert retention is secured by a Torx M5x18 screw, tightened with a T20 key to provide repeatable clamping. What is the overall length and how does it affect setup? The overall length is 210 mm, offering sufficient reach for many turret and milling spindle set-ups while balancing rigidity. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
49mm Boring Bar for VER27 Indexable Inserts, 300mm Length, 40mm Shank - Teknik Makina
Benefit from the combination of a 49 mm cutting diameter and a 300 mm overall length to achieve stable, repeatable internal boring with VER27 indexable inserts; order the drill bar directly via Metav Werkzeuge or request technical advice from the sales team. Drill bar for VER27 indexable inserts — 49 mm diameter, L300 mm (Teknik Makina) Drill bar engineered for indexable-insert boring operations, compatible with VER27 inserts and suited to production and workshop machining tasks. 49 mm nominal diameter for rigid cutting 300 mm overall length for deeper reaches Compatible with VER27 indexable inserts 40 mm shank diameter for secure mounting Stable, high-precision boring through larger diameter and length The tool’s 49 mm nominal diameter combined with a 300 mm overall length provides a favourable stiffness-to-length ratio that supports stable cutting in internal boring applications. By accepting VER27 indexable inserts, the system separates cutting geometry from the bar itself, enabling fast insert changes and consistent edge geometry for repeatable results. Indexable inserts reduce setup time and materials waste compared with brazed tips, while enabling easy replacement when wear occurs. This configuration benefits production runs where maintaining surface finish and dimensional accuracy across multiple parts is critical. Secure mounting and quick insert handling to reduce downtime A 40 mm shank ensures robust seating in standard holders, minimising micro-movement that can generate chatter or uneven tool wear. The clamping head is 25 mm wide, which provides a compact interface for the insert seat and promotes even clamping forces across the cutting edge. Clamping screws are tightened with a T20 Torx key, specified for repeatable torque application and straightforward maintenance. These design choices translate into fewer interruptions on the shop floor, lower rework rates and a measurable improvement in cycle-time efficiency for indexable-insert operations. Integration into workshop tooling and production lines Designed for machine-shop environments, the bar is compatible with common tool posts and boring heads where a 40 mm shank is accepted, facilitating straightforward integration into existing setups. The overall mass of the assembly (approx. 3.11 kg) contributes to inertial stability during cutting, while the modular nature of indexable inserts supports economical stocking strategies: replacement inserts rather than whole-tool renewals. Specification-led procurement and clear technical data simplify purchasing and spare-part planning, which aligns with Metav’s approach to reliable supply and centralised workshop provisioning. For ordering and compatibility checks, choose Teknik Makina’s robust 49 mm drill bar and contact Metav Werkzeuge for detailed integration support and procurement assistance. Technical data Article number: K345-6TM Label: 49mm Bohrstange VER27 L300mm Product type: Drill bar Brand: Teknik Makina Diameter: 49 mm Overall length: 300 mm Shank diameter: 40 mm Clamping head width: 25 mm Weight: 3.11 kg eClass: 21180806 Compatible with VER27 indexable inserts Torx key required: T20 Category: Drill bars FAQ Which indexable inserts fit the bar? The bar is compatible with VER27 indexable inserts as specified for the Tekniк Makina K345-6TM drill bar. What are the main dimensions of the tool? The tool features a 49 mm diameter and an overall length of 300 mm, with a 40 mm shank diameter. What clamping interface is used for the inserts? Insert clamping is handled via a 25 mm clamping head with screws requiring a T20 Torx key for secure tightening. Is the shank suitable for standard toolholders? A 40 mm shank is specified to ensure secure mounting in holders and tool posts designed for that shank size. What advantages do indexable inserts provide in this setup? Using indexable inserts allows rapid edge replacement, consistent cutting geometry and cost-efficient spare-part stocking compared with fixed-tip tools. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Achieve exact bores with a boring bar with internal coolant
A boring bar with internal coolant is a specialised tool for internal machining on lathes and machining centres, designed to enlarge and finish existing holes to precise dimensional and form tolerances. Also referred to as an internal coolant boring bar or coolant‑fed boring bar, this tool class routes coolant through the tool body so that cutting edges are supplied directly with fluid under pressure.
How internal coolant keeps deep and blind bores reliable
When machining with external coolant only, the fluid is delivered from outside via machine nozzles and often fails to reach the cutting zone in longer bores, leaving chips trapped and increasing thermal load. A boring bar with internal coolant contains axial coolant channels that run through the tool shank to the cutting edge, delivering high‑pressure coolant where it is needed. This arrangement is essential for machining deep bores, blind holes and for materials that produce long, continuous chips; it lowers local temperatures, flushes chips out of the bore and reduces the risk of tool breakage and surface damage.
Key advantages that improve productivity
- Faster cycle reliability: internal coolant reduces thermal distortion and helps maintain tight tolerances over longer runs.
- Improved chip evacuation: pressurised coolant clears chips from the cutting zone, preventing chip clogging and re-cutting.
- Extended tool life: cooler cutting edges and effective flushing reduce wear and the likelihood of catastrophic tool failure.
- Process versatility: suitable for deep bores and blind holes, especially in difficult‑to‑machine or long‑chipping materials.
Metav as the practical partner for precision tooling
Metav stands for the democratisation of precision and is positioned as a pragmatic partner for industry and workshops. Based in Emmerich, Metav combines hands‑on technical expertise with a broad supply range: over 250,000 products and a proven track record with more than 48,000 customers, ensuring steady availability and a quality filter for the European market. For buyers seeking coolant‑fed solutions, Metav offers curated assortments and selection guidance for boring bars with internal coolant.
In summary, a boring bar with internal coolant delivers targeted cooling and chip control that is indispensable for deep and blind bores, improving tolerance control, tool life and process stability.
FAQ
When should a boring bar with internal coolant be chosen over external coolant?
Select a boring bar with internal coolant whenever bores are deep or blind, or when machining hard‑to‑cut or long‑chipping materials; the internal coolant ensures reliable chip evacuation and temperature control where external coolant cannot reach.
How do axial coolant channels reduce the risk of tool breakage?
Axial coolant channels feed high‑pressure coolant directly to the cutting edge, lowering thermal stress at the point of generation and flushing chips away, which together reduce flank wear and the chance of sudden tool failure when using a boring bar with internal coolant.
Can internal coolant boring bars be used on both lathes and machining centres?
Yes. The internal coolant design is compatible with standard toolholders used on lathes and machining centres, making the internal coolant boring bar a flexible choice across machine platforms.
Which workpiece materials benefit most from coolant‑fed boring bars?
Materials that produce long, continuous chips or that are prone to thermal softening during cutting—such as certain stainless steels and high‑strength alloys—benefit markedly from the chip flushing and cooling provided by a boring bar with internal coolant.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com