Digital calipers for fast, reliable dimensional control
Digital calipers and precision calipers deliver fast, repeatable length measurements for metalworking, woodworking and electronics applications, reducing rework and speeding up inspection workflows. Designed with robust stainless steel bodies, high-resolution digital displays and capacitive sensors, these measuring tools provide high accuracy, easy data output and mm/inch conversion for seamless integration into quality processes. Suitable for production, workshop and lab use, they offer durable performance and intuitive operation to support consistent tolerance control.
150mm Precision Caliper E‑Ink Display, Round Depth Gauge, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Benefit from industrial-grade measurement accuracy combined with modern data handling: a 0–150 mm measuring range with ±0.015 mm accuracy, E‑Ink readability and wireless plus USB output. Delivered fully calibrated to ISO 17025 with certificate, this combination supports reliable quality control and efficient data workflows. Order the Precision Caliper directly via Metav Werkzeuge or ask our consultants if needed. Precision Caliper (0–150 mm) with E‑Ink display – Microtech Metrology Precision Caliper designed for workshop and laboratory measurement tasks, offering wireless and USB data transfer and a low‑power E‑Ink readout for clear values in production environments. E‑Ink 2.13" display for clear readout Wireless and USB data output ISO 17025 calibrated with certificate Rounded depth gauge for stable depth checks Built for accurate inspection and traceability The instrument provides a 0–150 mm measuring range classified in the standard class for general machine‑shop and metalworking inspection tasks. With a stated accuracy of ±0.015 mm, the device supports repeatable dimensional checks for components and assemblies where industrial tolerance control is required. The included calibration to ISO 17025 ensures traceability and acceptance in formal quality procedures; the delivered calibration certificate documents conformity and simplifies audit evidence. Seamless data capture for modern workflows Equipped with an E‑Ink 2.13" display and Wireless + USB data output, the caliper removes manual transcription steps and integrates with digital quality systems. The E‑Ink readout is easy to read under workshop lighting and consumes very little power, reducing battery changes and downtimes. Wireless transfer and USB connectivity enable direct logging of measurement results into spreadsheets or measurement software, supporting faster inspection cycles and minimising input errors in production control. Practical design for everyday workshop use The tool features a rounded depth gauge that improves contact stability when measuring recesses and stepped features. Jaw geometry and a tip length of 40/16 mm maintain access to confined areas while keeping the measuring faces aligned for consistent results. The digital format with a low‑power display offers the convenience of fast readings combined with a robust, easy‑to‑use mechanical form suited to routine shopfloor measurement tasks. Certified calibration and documented reliability Delivered fully calibrated according to ISO 17025, the caliper arrives ready for use in formal inspection routines; a calibration certificate is included with the product. The documented calibration removes the need for an immediate in‑house recalibration and supports compliance requirements in incoming inspection or final quality tests. For operations seeking reproducible measurement data and audit‑ready traceability, this instrument supplies the necessary evidence chain. For certified precision and seamless data capture, request the Microtech Metrology Precision Caliper from Metav Werkzeuge or contact our specialists in Emmerich for tailored advice Technical data Article number: 141093015R GTIN: 4061905455391 Manufacturer: Microtech Metrology Facts Measurement range: 0–150 mm Accuracy: ±0.015 mm Display resolution: 0.005 mm Display type: E‑Ink 2.13" Data output: Wireless + USB Special features Rounded depth gauge Jaw/tip length: 40/16 mm Digital caliper, E‑Ink readout Delivered with ISO 17025 calibration certificate Digital instrument suitable for workshop and lab use FAQ Is the caliper ready for use in quality audits? The Precision Caliper is delivered fully calibrated to ISO 17025 and supplied with a calibration certificate, making it suitable for audit‑grade measurement tasks. Which data interfaces are available for integration? Measurement data can be exported via the caliper’s wireless connection or the USB port for direct import into measurement software and data logs. What precision can be expected from the instrument? The device specifies an accuracy of ±0.015 mm with a display resolution of 0.005 mm, appropriate for standard workshop quality control. Is the depth gauge suitable for recessed measurements? Yes, the caliper includes a rounded depth gauge designed to provide stable contact and reproducible results when measuring steps and recesses. For which applications is this caliper best suited? With a 0–150 mm range and industrial accuracy, the instrument is ideal for general machine‑shop inspection, incoming part checks and routine dimensional control. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
150mm Precision Caliper E‑Ink Display, Round Depth Gauge, Wireless/USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of reliable E‑Ink readability, wireless data transfer and traceable ISO 17025 calibration to streamline workshop inspections; the combination of precise measurement, robust handling and certified calibration supports consistent quality control. Order the Precision Caliper directly via Metav Werkzeuge or consult our specialists for application advice. Precision Caliper 0–150 mm — E‑Ink 2.13" display, Wireless+USB (Microtech Metrology) The Precision Caliper is a digital measuring instrument for workshop and quality‑control tasks, designed to combine clear E‑Ink legibility with wireless and USB data transfer for efficient inspection workflows. E‑Ink 2.13" display for clear readings Wireless+USB data output for easy capture ISO 17025 calibrated with certificate Consistent accuracy for everyday quality control This caliper delivers a 0–150 mm measuring range that places it in the Standard class for machine‑tool and metal‑working shops, offering an optimum balance of reach and rigidity. With a stated resolution of 0.01 mm and a fine display reading of 0.005 mm, the instrument supports routine tolerancing and first‑article checks with industrial‑grade repeatability. The benefit to production is straightforward: measurable dimensions that conform to accepted workshop tolerances, reducing rework and inspection uncertainty. Readability and data flow that speed inspection rounds The E‑Ink 2.13" display provides high contrast with minimal power consumption, which is particularly valuable in bright workshop lighting and long shift use. Paired with Wireless+USB data output, the instrument allows measured values to be transferred directly to inspection software or a spreadsheet, avoiding manual transcription errors. This data‑ready concept accelerates batch sampling and statistical process control, so inspection steps take less time while generating a reliable digital record. Robust measuring concept for reliable handling The caliper's measuring force is engineered for stability: double measuring force with 8 N for external jaws and 4 N for internal jaws reduces the effect of variable hand pressure on results. A rounded depth gauge improves access into recesses and reduces the risk of catching on workpiece edges during depth checks. These design choices translate into fewer measurement artefacts and a more predictable usage experience when measuring parts with shoulders, grooves or stepped profiles. Certified calibration and traceability to support quality systems Delivered fully calibrated to ISO 17025, the tool includes a calibration certificate that documents traceability and measurement uncertainty. This is essential for suppliers and workshops operating under quality standards or customer audits, because the certificate demonstrates an independent verification of performance. Having this documentation with the instrument simplifies incoming inspection and quality records, and it supports confident decision‑making when parts require acceptance or rejection. Practical integration into the workshop environment Lightweight and compact for handheld use across benches, the instrument suits typical shop applications such as component checks, fixture alignment and small assembly verification. The wireless and USB interfaces allow connection to common data loggers or inspection benches while the E‑Ink screen remains readable in variable light. The result is a straightforward, low‑effort tool that helps maintain throughput without sacrificing traceability or precision. For immediate supply and technical advice on the Microtech Metrology Precision Caliper with ISO 17025 calibration, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: 141093015FR GTIN: 4061905455414 Brand: Microtech Metrology Category: Digital caliper Calibration: ISO 17025 certificate included Facts Measuring range: 0–150 mm Resolution: 0.01 mm Display reading: 0.005 mm Display size: 2.13" Measuring force: 8 N (external), 4 N (internal) Special features E‑Ink 2.13" display Wireless+USB data output Rounded depth gauge Digital instrument (electronic display) Delivered with calibration certificate (ISO 17025) FAQ What measuring range does the caliper cover? The caliper covers a measuring range of 0–150 mm, placing it in the Standard category for workshop and machine‑shop use. Is the instrument delivered calibrated? Yes, the tool is supplied fully calibrated to ISO 17025 and includes a calibration certificate for traceability. How are measurements exported from the caliper? Measured values can be exported via Wireless connection or USB, enabling direct capture into inspection software or data logs. What is the display type and its advantage? The instrument uses an E‑Ink 2.13" display, which offers high contrast, low power consumption and good legibility under workshop lighting. How does the caliper handle operator‑induced variation? A double measuring force (8 N external / 4 N internal) stabilises contact pressure and reduces variation caused by differing hand pressure during measurement. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
150mm Precision Caliper E‑Ink Display, Wireless USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of the combination of certified traceability, a low-profile E‑Ink display and flexible data transfer for faster inspection cycles; the fully ISO 17025 calibrated instrument supports reliable decisions on the shop floor. Order the caliper directly via Metav Werkzeuge or consult the Metav team for application advice. Precision Caliper (0–150 mm) by Microtech Metrology — E‑Ink display & Wireless+USB A Precision Caliper for workshop and quality‑control tasks, offering a clear 2.13″ E‑Ink display, USB and wireless data transfer, and factory calibration to ISO 17025. E‑Ink 2.13″ display for clear readings Wireless and USB data output ISO 17025 calibration with certificate 0–150 mm standard measurement range Round depth gauge included Certified accuracy that shortens inspection loops The instrument arrives fully calibrated to ISO 17025, supplied with a calibration certificate for immediate use in traceable quality procedures. The combination of a fine 0.01 mm resolution and an indicated accuracy of ±0.015 mm makes the tool suitable for standard workshop tolerances and routine incoming‑goods checks. These specifications reduce rework and speed approvals because measurements are both reproducible and auditable within established quality systems. Fast data capture for modern measurement workflows Integrated Wireless+USB data output avoids transcription errors and connects directly to inspection software or spreadsheets, increasing throughput during serial checks. The low‑power E‑Ink display remains readable under workshop lighting and minimises battery changes, while the digital readout ensures clear numeric values. The caliper’s electronic interface supports streamlined documentation and saves time when logging results for certificates or batch records. Robust, practical design for daily use Designed for the universal shop standard, the 0–150 mm range is classified as Standard, offering a balance between reach and rigidity for most machine‑shop tasks. A round depth gauge is fitted for reliable depth and step measurements, turning a single instrument into a versatile inspection tool. The housing and linear guide are engineered for repeatable handling; this reduces operator influence on readings and maintains stable performance across shifts. What inspectors and machinists gain in practice Using a calibrated digital caliper with direct data output improves traceability and reduces administrative overhead during audits or supplier checks. The device replaces manual note‑taking with error‑free digital transfer, while the ISO 17025 certificate supports integration into formal inspection routines. For teams seeking dependable everyday measurement, this instrument combines clarity, connectivity and certified accuracy to meet typical industrial quality demands. Contact Metav Werkzeuge for personalised advice and secure this Microtech Metrology Precision Caliper with ISO 17025 certificate and Wireless+USB output for immediate integration into production control. Technical Data Article number: 141093015B GTIN: 4061905100130 Brand: Microtech Metrology eCl@ss: 21170344 Facts Measuring range: 0–150 mm Resolution: 0.01 mm Indicated accuracy: 0.015 mm Display size: 2.13″ Special features Digital instrument, E‑Ink 2.13″ display Data output: Wireless + USB Supplied calibrated to ISO 17025 with certificate Includes round depth gauge No measuring faces option specified FAQ How accurate is the caliper for routine quality checks? The caliper from Microtech Metrology delivers an indicated accuracy of ±0.015 mm with a 0.01 mm resolution, suitable for standard workshop and quality‑control inspections. Is the instrument ready to use for traceable measurements on arrival? Yes. The tool is supplied fully calibrated to ISO 17025 and includes a calibration certificate for immediate use in traceable measurement processes. Which data interfaces are available for recording results? Results can be exported via the integrated Wireless+USB connections, enabling direct transfer into inspection software or data logs. Does the caliper include a depth gauge for step and depth measurements? A round depth gauge is included, expanding the instrument’s use to depth and step measurements alongside external and internal checks. Is the 0–150 mm range suitable for general workshop applications? The 0–150 mm measuring span is classified as Standard, offering the best compromise between reach and stiffness for everyday machining and assembly tasks. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
150mm Precision Caliper Force Control 8N Two-Way, Swiss Digital 11mm Display, IP67, ISO 17025 - Microtech Metrology
Take advantage of the combination of robust industrial protection, precise 0.01 mm resolution and traceable ISO 17025 calibration for reliable quality control in every workshop; order the calibrated instrument via Metav Werkzeuge or contact the team for integration advice. Precision Caliper by Microtech Metrology — digital, wireless, IP67 The Precision Caliper is a digital measuring instrument designed for standard workshop and machine‑shop inspection tasks up to 150 mm, combining protected electronics and traceable calibration for dependable routine use. Digital display with 11 mm height Wireless data output for traceability IP67 protection for harsh environments ISO 17025 calibration with certificate Reliable measurement for everyday workshop use The caliper delivers 0.01 mm resolution, providing the fine gradation required for accurate pass/fail decisions in production and inspection. With a measurement range of 0–150 mm, the instrument fits the Standard class of calipers that balances reach and rigidity—ideal for common tasks in machine shops and metalworking. The clear Swiss Digital display (11 mm high) improves legibility on the shop floor and reduces reading errors, which shortens inspection cycles and increases throughput. Consistent contact force for repeatable results A bi‑directional measuring force of 8 N ensures a uniform contact pressure on the jaws, which reduces variation introduced by manual handling and improves repeatability between operators. Consistent force control translates into fewer reworks and more reliable quality data, as identical contact conditions produce comparable results across multiple measurements. Robust design suited to industrial environments Rated IP67, the caliper is dustproof and protected against temporary immersion, making it suitable for harsher production areas where coolant mist or particulate contamination can be an issue. The ruggedised electronics and sealed slider extend service intervals and reduce downtime, while the compact jaw geometry supports access to confined features without sacrificing stiffness. Traceable calibration and seamless data workflow Calibrated to ISO 17025 and supplied with a calibration certificate, the instrument supports formal quality systems and audit trails. The wireless data output enables direct transfer of measurement values into data collectors or SPC systems, cutting manual transcription and the risk of input errors. These features together create a more efficient measurement process and clearer documentation for quality records. Contact Metav Werkzeuge in Emmerich for technical advice and to request the ISO 17025 certificate for the Microtech Metrology precision caliper with wireless data output Technical data Article number: 141078192 GTIN: 4061905036514 Manufacturer: Microtech Metrology Facts Measurement range: 0–150 mm Resolution: 0.01 mm Display height: 11 mm Measuring force: 8 N Protection class: IP67 Special features Digital display (Swiss Digital) Wireless data output ISO 17025 calibration with certificate Jaw lengths: 40/16 mm FAQ Is the caliper delivered calibrated? Yes. The caliper is supplied with an ISO 17025 calibration certificate; the Microtech Metrology precision caliper is ready for traceable use on arrival. What accuracy can be expected at 150 mm? The instrument offers 0.01 mm display resolution; for a 150 mm range a typical digital caliper error band is in the order of ±0.03 mm, consistent with standard digital workshop calipers. Can measurement data be collected automatically? The wireless data output supports direct capture of values from the caliper into data logging and SPC workflows, enabling efficient digital documentation. Is the caliper suitable for wet or dusty environments? With an IP67 rating the caliper is dust tight and protected against immersion up to 1 m for a limited time, making it appropriate for many industrial shop conditions. Why is a defined measuring force important? A fixed 8 N measuring force reduces operator‑dependent variability. Consistent contact pressure improves repeatability and lowers the likelihood of measurement scatter. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
150mm Precision Caliper Force Control 8N Two‑Direction Digital, Swiss Display 11mm, IP67, ISO 17025 - Microtech Metrology
Benefit from laboratory-grade traceability and everyday robustness: the caliper combines ISO 17025 calibration with IP67 protection and a clear Swiss Digital 11 mm display for dependable workshop measurements; its controlled 8 N bidirectional measuring force and 0–150 mm range keep inspections fast and repeatable. Order the precision caliper directly via Metav Werkzeuge or ask our consultants if needed. Precision Caliper by Microtech Metrology — ISO 17025 calibrated, IP67, Swiss Digital (11 mm) A Precision Caliper designed for workshop and laboratory use with a 0–150 mm measuring range and controlled 8 N bidirectional measuring force for repeatable results ISO 17025 calibration included IP67 dust and water protection Swiss Digital 11 mm high-contrast display 0–150 mm workshop range with 8 N force Laboratory traceability meets workshop practicality This digital caliper is supplied fully ISO 17025 calibrated and includes a calibration certificate, which transfers laboratory traceability directly into routine quality checks. The delivered certificate documents measurement accuracy and supports audit trails, making the instrument suitable for regulated environments as well as the production floor. With a Swiss Digital readout and an 0.01 mm display resolution, the instrument provides the standard numerical clarity expected in assemblies and incoming inspection. Designed for reliable results in everyday measurement tasks Classified in the Standard range for calipers (0–150 mm), this instrument balances reach, stiffness and one-handed usability to suit general engineering and metalworking tasks. The IP67 rating reduces downtime from contaminants and coolant exposure, while the 8 N bidirectional measuring force keeps contact pressure consistent and reduces operator‑induced variation. Together these features improve repeatability and reduce the frequency of rejected parts during routine quality control. Clear readout and handling that speeds inspection A tall, high-contrast Swiss Digital display (11 mm) keeps readings legible across a range of lighting conditions, which accelerates inspection throughput and reduces transcription errors. The caliper’s jaw geometry (40/16 mm) offers secure contact for internal and external measurements without awkward handling. The combination of a controlled measuring force and a robust digital system supports reliable zeroing and quick switching between tasks, making this instrument a practical addition to production lines and measurement benches. For measurement tasks demanding lab-level evidence and workshop durability, contact Metav Werkzeuge to request the ISO 17025‑calibrated Microtech Metrology precision caliper and confirm suitability for specific applications Technical data Article number: 141078122 GTIN: 4061905036460 Manufacturer: Microtech Metrology ECLASS: 21170344 Core data Measuring range: 0–150 mm Display resolution: 0.01 mm Display height: 11 mm Measuring force: 8 N Protection class: IP 67 Digital readout: Swiss Digital Features ISO 17025 calibration included with certificate Bidirectional controlled measuring force Jaw length: 40/16 mm Digital instrument suitable for workshop and laboratory use FAQ Is a calibration certificate supplied with the caliper? Yes. The Microtech Metrology precision caliper is supplied fully calibrated to ISO 17025 and a calibration certificate is included with the instrument. What does IP67 protection mean for workshop use? IP67 indicates the caliper is dust-tight and protected against temporary immersion, reducing contamination risks from coolant or chips during metalworking. What measurement resolution and accuracy can be expected? The digital readout provides a resolution of 0.01 mm and a clear numeric display; the ISO 17025 calibration documents the instrument’s performance for traceable use. How does the 8 N measuring force affect results? A controlled 8 N bidirectional measuring force stabilises contact pressure, improving repeatability and lowering operator-induced measurement variance. Is this caliper suitable for precision laboratory tasks as well as shop floor work? Yes. With ISO 17025 calibration, a high‑contrast Swiss Digital display and IP67 protection, the instrument bridges laboratory traceability and robust shop-floor handling. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
150mm Precision Caliper Low Measuring Force, Swiss Digital Display 11mm, IP67 - Microtech Metrology
Benefit from precise, low‑force measurement and IP67 protection for reliable workshop results; take advantage of the clear Swiss digital readout and Standard 0–150 mm range — order the Precision Caliper directly via Metav Werkzeuge or ask our consultants if needed. Precision Caliper by Microtech Metrology — IP67, Swiss Digital 11 mm display The Precision Caliper is a digital measuring instrument designed for workshop and laboratory use, offering a 0–150 mm range and a low measuring force for sensitive components. High-contrast Swiss digital display 11 mm IP67-rated protection against dust and water Low measuring force (0.8 N) for delicate parts 0–150 mm standard measuring range Precision where it matters The instrument delivers repeatable results across its 0–150 mm span, placing it in the Standard class that balances reach and rigidity for most machine‑shop tasks. The combination of a clear Swiss digital display and a low measuring force (0.8 N) reduces operator influence on small or thin parts, which helps preserve tolerances during routine checks. As a digital measuring tool, it supports fast measurement cycles with unambiguous readings, making it suitable for quality control stations and assembly benches where throughput and reliability are required. Built for workshop conditions and easy reading Robustness is a practical benefit: the caliper is rated IP67, so temporary exposure to dust or water does not compromise the electronics, enabling use at workstations where coolant mist or chips are present. The 11 mm high Swiss display improves legibility under workshop lighting and reduces reading errors compared with smaller indicators. The sealed construction and solid display contribute to lower downtime for maintenance and fewer measurement interruptions in daily production workflows. Handling, application and operational advantages Designed for straightforward operation, the digital slider enables single‑handed measuring and quick repositioning. The combination of the Standard 0–150 mm range and the gentle contact pressure makes the instrument particularly well suited to metalworking, toolroom checks and inspection of delicate assemblies. Procurement through Metav benefits from a European quality filter and reliable logistics from the Emmerich warehouse, ensuring the caliper arrives ready for immediate use in the workshop environment. Contact Metav Werkzeuge for technical advice on the Microtech Metrology caliper or request supply directly from our Emmerich warehouse Technical data Article number: 141077153 GTIN: 4061905036477 Manufacturer: Microtech Metrology Eclass: 21170344 Digital display: Swiss Digital, 11 mm Key figures Measuring range: 0–150 mm Measuring force: 0.8 N Protection class: IP67 Digital: yes Features and applications Standard measuring range (classification: Standard) Low measuring force reduces deformation of delicate parts Dust‑ and water‑resistant design for workshop use High‑visibility Swiss digital display for unambiguous readings Intended for machine shops, toolrooms and quality control FAQ Is this caliper suitable for everyday workshop use? The Precision Caliper from Microtech Metrology is designed for workshop and laboratory environments; IP67 protection and a robust digital readout make it suitable for routine inspection tasks. What measuring range does the instrument cover? The instrument covers a 0–150 mm measuring range, matching the Standard class that combines reach and stiffness for typical machine‑shop requirements. Will the low measuring force affect measurement reliability? The 0.8 N contact pressure minimises deformation on thin or delicate parts while still providing consistent contact, which supports dependable comparative measurements in production. Is the display legible at a distance or under bright light? Yes. The caliper features a Swiss digital display with an 11 mm digit height, which improves readability and reduces the risk of transcription errors. Is a calibration certificate included with the caliper? The product data does not specify a supplied calibration certificate; if a formal certificate is required, please request clarification when ordering. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
150mm Precision Caliper With Round Depth Gauge And Preset Function, USB, IP54 - Microtech Metrology
Take advantage of reliable 0–150 mm measurement, 0.01 mm resolution and a practical USB data output to speed up quality control and documentation. The combination of a clear 11 mm digit display, IP54 protection and a preset function ensures robust daily use and fewer measurement errors. Order the precision caliper directly via Metav Werkzeuge or contact our consultants for application advice. Precision Caliper 0–150 mm by Microtech Metrology — digital with USB and preset The Precision Caliper is a digital measuring instrument for workshop and quality-control tasks, offering a 0–150 mm range, USB data output and a round depth gauge for versatile measurements Digital display 0.01 mm resolution USB data output for traceable export IP54 protection for workshop environments Preset function with round depth gauge Consistent, measurable accuracy to reduce rework The caliper delivers a resolution of 0.01 mm and an accuracy of ±0.02 mm, values that support reliable pass/fail decisions in production. Resolution refers to the smallest display increment, while accuracy indicates the typical deviation from a true value; together they determine whether a measuring result is suitable for incoming inspection or assembly checks. The clear 11 mm digit height improves readability at the measuring station, reducing interpretation errors and accelerating repetitive checks. These measurable attributes make the instrument a practical choice for routine quality control. Built for the workshop — protected, robust and ergonomic Designed with an IP54 rating, the instrument is protected against dust ingress and splashing liquids commonly found in workshop environments. The caliper’s jaws (40/16 mm) and the round depth gauge extend measurement capability to recessed features and step depths, while the compact slider and balanced geometry support one‑hand operation. IP54 and the sturdy construction reduce downtime and the need for frequent replacements, which translates into steadier throughput for production lines and maintenance bays. Seamless data capture to speed documentation Equipped with USB data output, the instrument integrates easily into a traceability workflow: measurement results can be exported directly for statistical process control or stored in inspection reports. The preset function enables a defined zero or reference point to be set quickly, simplifying comparative measurements and batch checks. For workshops aiming to reduce transcription errors and speed up reporting, this direct data path offers a tangible productivity benefit. A standard length that suits most tasks in metalworking With a measuring range of 0–150 mm, this caliper falls into the Standard category — the workshop baseline that balances reach and stiffness for general machine‑shop and metalworking tasks. That range is ideal for component inspection, fixture setup and routine maintenance, providing the reach needed for typical parts while maintaining handling comfort. The instrument’s specifications and features suit metal‑working, quality control and general maintenance operations where dependable, repeatable measurement is required. For secure procurement and product matching, contact Metav Werkzeuge in Emmerich — Metav’s specialists will advise on application suitability and arrange supply of the Microtech Metrology precision caliper via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Type: Digital precision caliper Manufacturer: Microtech Metrology SKU: 141081112R GTIN: 4061905455575 Category: Digital caliper Facts Measuring range: 0–150 mm Resolution: 0.01 mm Accuracy: ±0.02 mm Display digit height: 11 mm Jaw length: 40/16 mm Protection class: IP54 Data output: USB Special features Preset function Round depth gauge Digital display Suitable for standard workshop and QA tasks FAQ What is the measuring range and suitability for workshop use? The instrument offers a measuring range of 0–150 mm, placing it in the Standard category for general machine‑shop, metalworking and quality‑control tasks. How precise are the measurements and what do the numbers mean? Resolution is 0.01 mm and typical accuracy is ±0.02 mm. Resolution is the smallest displayed step; accuracy describes the expected deviation from the true dimension under normal use. Can measurement results be exported for documentation? Yes, the caliper provides a USB data output to transfer measured values directly into inspection software or spreadsheets for traceability. What does IP54 protection cover in practical terms? IP54 indicates protection against dust ingress to a level that does not interfere with operation, and against water splashes from any direction — suitable for typical workshop conditions. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
150mm Precision Digital Caliper 0.01/0.005mm Resolution, IP67, ISO 17025 Calibration - Microtech Metrology
Take advantage of a compact, inspection-ready measuring instrument that combines shop‑grade reach with laboratory traceability: a calibrated digital tool with ISO 17025 certificate, IP67 protection and a clear 9 mm display for fast readings. Order directly via Metav Werkzeuge or contact our consultants for application advice. Precision Caliper by Microtech Metrology — Digital, IP67, 0–150 mm The Precision Caliper is a digital measuring instrument for workshop and quality control tasks, offering a standard 0–150 mm range with depth‑measurement capability and a sealed construction suitable for industrial environments. IP67 dust and water protection ISO 17025 calibration certificate included 0–150 mm range for standard workshop use 0.01 mm resolution with 9 mm digital display Reliable measurement performance for quality control Designed for routine inspection and production control, this precision caliper delivers a 0–150 mm measuring range that matches common workshop requirements while maintaining compact handling. With a 0.01 mm resolution and a stated accuracy of ±0.02 mm, the instrument supports repeatable pass/fail checks and dimensional documentation. The large 9 mm display speeds up read‑out and reduces transcription errors, which contributes directly to shorter inspection cycles and fewer downstream rejects. Robust design that keeps workshops running Sealed electronics and an IP67 rating mean the instrument tolerates dust and temporary immersion, so measurement tasks remain possible in damp or oily conditions without immediate risk to the electronics. The caliper includes a dedicated depth measurement function for grooves and recesses, extending usefulness beyond simple internal and external checks. Together, these features reduce interruptions caused by instrument failure and lower the likelihood of measurement‑related rework. Traceability and audit readiness from delivery This digital instrument is supplied fully calibrated under ISO 17025, and a calibration certificate is included with delivery, providing documented traceability for quality management systems and external audits. The combination of laboratory calibration and workshop robustness means the tool is ready for immediate use in inspection plans, supplier checks or incoming goods control, reducing the preparatory effort before first use. Practical applications and operational benefits Ideal for machine shops, metalworking and quality departments, the caliper is suitable for routine dimensional checks, set‑up verification and small assembly control tasks. Its balance of stiffness and reach covers most daily measurement needs while remaining easy to handle for one‑person operation. The sealed display and clear digits also support faster training of operators, helping teams maintain throughput with consistent measurement quality. Contact Metav Werkzeuge today to secure a calibrated Microtech Metrology digital caliper with ISO 17025 certificate and expert advice on integration into inspection routines Technical Data Article number: 141085102 GTIN: 4061905451478 Manufacturer: Microtech Metrology Eclass: 21170344 Facts Measuring range: 0–150 mm Resolution: 0.01 mm Display digit height: 9 mm Accuracy: ±0.02 mm Protection rating: IP67 Digital display: yes Measuring functions: depth measurement Special features ISO 17025 calibration certificate included Standard workshop category (100–300 mm) Depth measurement capability Sealed electronics for harsh environments FAQ Is the caliper delivered calibrated? Yes. The instrument is supplied fully calibrated and includes an ISO 17025 calibration certificate as standard. What accuracy and resolution can be expected? The digital caliper offers 0.01 mm resolution with an overall accuracy of approximately ±0.02 mm, suitable for routine industrial quality checks. Can the caliper be used in wet or dusty conditions? The IP67 rating means the caliper is protected against dust ingress and temporary immersion, allowing use in many demanding workshop environments. Does the instrument measure depths and steps? Yes. The tool features a dedicated depth measurement function in addition to internal and external jaws for versatile inspections. Is this caliper suitable for incoming goods inspection and audits? Yes. Delivery includes an ISO 17025 calibration certificate, making it suitable for audit‑traceable inspection processes. Which brand manufactures this instrument? The caliper is produced by Microtech Metrology, a supplier of precision measuring instruments. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
150mm Precision Digital Caliper With Ceramic Interchangeable Insert, Preset, Stainless Steel, Supplied In Case - Metav IndustryLine
Take advantage of the combination of compact 150 mm measuring range, ceramic measuring insert and flexible probe mounting for precise, repeatable inspection results; order directly via Metav Werkzeuge or consult the technical team for application advice. Digital Uni caliper 150 mm x 40 mm — Digital caliper with ceramic insert and M2.5 probe thread by Metav IndustryLine The Digital Uni caliper 150 mm x 40 mm is a compact digital precision caliper for general workshop inspection and quality control, featuring a ceramic insert with preset and a through-thread for interchangeable measuring tips. *Digital display with SET/PRESET button *M2.5 through-thread for probe inserts *Ceramic measuring insert for wear resistance *Standard 0–150 mm range for workshop use Precise, measurable results for routine inspections The instrument combines a 150 mm measuring range with a high-contrast digital display and 0.01 mm resolution, delivering measurable improvements in inspection repeatability compared with coarse mechanical gauges. The specified measurement tolerance of ±0.04 mm positions this tool within reliable workshop accuracy for assembly checks and component verification. The hardened stainless steel construction with metal housing resists wear and maintains jaw alignment, which reduces systematic error over frequent use and supports consistent quality control. Flexible probe options for specialised tasks A through-thread with M2.5 specification accepts interchangeable measuring inserts, making the caliper adaptable to restricted or contoured measuring points. The device includes two 2 mm ball measuring heads and a ceramic insert with preset, which provides a wear-resistant contact surface and fast setup for repeat measurements. This modular approach reduces downtime for fixture changes and extends the usable life of the instrument by allowing targeted replacement of wear parts rather than the entire gauge. Data handling, workshop integration and practical design Equipped with an RB 5 data output, the caliper supports straightforward integration into measurement logging workflows and avoids manual transcription errors during batch inspections. The digital unit features an ON/OFF and SET/PRESET interface for quick zeroing and reference capture, and runs on a standard 3 V supply for ease of maintenance. With a compact jaw length and a balanced weight, the tool is classified as Standard for calipers (suitable for the everyday needs of machine shops and metalworking), offering the best compromise between reach, stiffness and one-handed handling for 150/200/300 mm baseline tooling. For dependable workshop precision from Metav IndustryLine, request a detailed specification or application consultation from Metav Werkzeuge — technical advice and secure delivery are available from Emmerich. Technical Data SKU: M240.205.N GTIN: 4054469159997 TARIC: 90173000 Facts Measuring range: 0–150 mm Resolution: 0.01 mm Accuracy: ±0.04 mm Weight: 0.48 kg Jaw length: 45 mm Power supply: 3 V Special features Stainless, hardened steel with metal housing Ceramic measuring insert with preset Through-thread M2.5 for interchangeable probes Includes two 2 mm ball measuring heads Digital display with ON/OFF and SET/PRESET Data output: RB 5 FAQ Is this caliper suitable for general workshop measurement tasks? The Digital Uni caliper 150 mm x 40 mm (Metav IndustryLine, SKU M240.205.N) is designed for standard workshop and machine‑shop inspection, offering a practical balance of reach and stiffness for everyday use. Can the measuring probes be replaced for special applications? Yes. The tool features an M2.5 through-thread and is supplied with two 2 mm ball measuring heads; additional probes with compatible M2.5 mounting can be fitted for specialised measurements. What level of accuracy and resolution can be expected? The caliper provides a resolution of 0.01 mm and a specified accuracy of ±0.04 mm, which is appropriate for routine quality checks and part inspections in mechanical workshops. Does the instrument support data logging? The caliper includes an RB 5 data output for connection to data collection systems, enabling direct transfer of measurement values for documentation and process control. Is the ceramic insert intended for heavy-duty use? The ceramic measuring insert offers improved wear resistance and stable contact for repeated measurements; it is particularly useful where metallic contact surfaces would otherwise degrade faster. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Precision Digital Caliper With Preset Function, IP54 Protection, 11mm Digit Height USB Output - Microtech Metrology
Benefit from workshop‑ready durability and precise repeatability: the combination of IP54 protection, PRESET function and USB data output keeps production checks fast and traceable. Order directly via Metav Werkzeuge or contact our consultants for advice and compatibility information. Precision Caliper (digital) with IP54, PRESET — Microtech Metrology The Precision Caliper is a digital workshop caliper for routine dimensional checks up to 150 mm, offering splash‑resistant IP54 protection and a PRESET function for consistent reference settings. Digital display with 11 mm digit height IP54 splash and dust protection PRESET function for repeatable references USB data output for traceable readings Robust protection for everyday measuring reliability Equipped with IP54 enclosure sealing, this digital measuring instrument tolerates workshop dust and occasional splashes while maintaining stable readings. The instrument is designed for the Standard measuring category, covering a measuring range of 150 mm that balances reach and rigidity for typical machine‑shop tasks. With an indicated accuracy of ±0.02 mm, the device delivers industry‑grade repeatability; the display resolution of 0.01 mm supports fine readouts without the complexity of submicron instruments. This combination reduces rework and increases throughput in routine inspection and setup operations. Fast data capture and repeatable setups to support quality control The integrated PRESET function simplifies changeovers by letting operators store a reference dimension for repeated checks, reducing setup time and human error. Measurements can be exported via USB for documentation and process traceability, which supports batch reporting and digital quality records. The clear 11 mm high digits on the digital display make values easy to read across a busy bench, and the standard electronic interface is compatible with common data‑logging workflows. The Precision Caliper therefore combines operational convenience with measurable control over quality processes. Practical features that improve shop performance Designed for general workshop and maintenance work, the caliper includes an integrated depth gauge for step and recess measurements and a robust slider for confident two‑hand operation when required. Construction and function focus on user efficiency: straightforward button layout, quick PRESET access and a stable measuring carriage to limit parallax or play. As a product from Microtech Metrology, it suits production, inspection and toolroom environments where dependable, documentable measurements are required without investing in laboratory‑only instruments. For traceable, workshop‑grade measuring with Microtech Metrology’s PRESET‑equipped digital caliper, contact Metav Werkzeuge in Emmerich for tailored advice or to confirm compatibility with existing data systems — info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: 141081112 GTIN: 4061905454592 ECLASS: 21170344 Manufacturer: Microtech Metrology Facts Measuring range: 0–150 mm Resolution: 0.01 mm Accuracy: ±0.02 mm Digit height: 11 mm Special features IP54 protection PRESET function Data output: USB Digital display: yes Depth gauge: integrated Type: digital caliper Measurement class: Standard (up to 150 mm) FAQ What measuring range does this caliper cover? The caliper covers a measuring range of 0–150 mm and is classified as a Standard workshop caliper suitable for general machine‑shop use. How precise are the readings from this instrument? Readings are provided with a resolution of 0.01 mm and an indicated accuracy of ±0.02 mm on the Microtech Metrology digital caliper (SKU 141081112). Does the caliper support data export for documentation? Yes. The instrument features a USB data output for direct transfer of measured values into inspection records or data‑logging systems. What is the benefit of the PRESET function? The PRESET function allows a stored reference to be recalled for repeat measurements, improving repeatability and reducing setup time during serial checks. Is the caliper suitable for shopfloor use? With IP54 protection and a sturdy slider, the caliper is designed for shopfloor conditions, where dust and occasional splashes occur. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
150–300mm Digitaler Präzisionsmessschieber, 0,01mm Auflösung, Wireless Daten, ISO 17025 Kalibrierzertifikat, handgefertigte Messbacken - Microtech Metrology
Der Präzisionsmessschieber verbindet hohe Auflösung, wireless Datenausgabe und ISO 17025 Kalibrierung zu einem zuverlässigen Messmittel für Fertigung und Labor. Nutzen Sie die Kombination aus Auflösung 0,01 mm und nachweislicher Kalibrierung für reproduzierbare Prüfabläufe; Metav Werkzeuge liefert und berät bei Bedarf direkt weiter. Präzisionsmessschieber von Microtech Metrology Der Präzisionsmessschieber ist eine digitale Schieblehre für präzise Werkstatt‑ und Qualitätskontrollen bis 300 mm. Präzisionsmessschieber »141072392C« von Microtech Metrology Digitalanzeige, Displayhöhe 11 mm Auflösung 0,01 mm, Fehlergrenze ±0,03 mm wireless Datenausgang für Datenübertragung Handgefertigte Messbacken und Tiefenmaß Höchste Präzision mit nachweisbarer Kalibrierung Mit einer Auflösung von 0,01 mm und der Einordnung in den digitalen Industriestandard bietet dieses Messwerkzeug zuverlässige Messwerte für Serienprüfungen. Die Kalibrierung erfolgt nach ISO 17025 und das Gerät wird mit einem Kalibrierzeugnis ausgeliefert, sodass Messunsicherheit dokumentiert und Prüfprozesse auditfähig bleiben. Diese Kombination reduziert Nachmessungen und erhöht die Prozesssicherheit in der Fertigung. Robustheit und Messkomfort für den Werkstattalltag Die handgefertigten Messbacken und die präzise geführte Schiene sorgen für lange Standzeit und geringe Messabweichungen bei wiederholten Messungen. Das integrierte Tiefenmaß erweitert die Einsatzmöglichkeiten über reine Außen‑ und Innenmessung hinaus. Die angegebene Schnabellänge 60/21 unterstützt das sichere Ansetzen an Bauteilen mit begrenztem Freiraum, ohne auf Stabilität zu verzichten. Geeignet für Maschinenbau, Qualitätskontrolle und Werkstatt Als Standard‑Kategorie mit einem Messbereich bis 300 mm deckt dieses Messgerät typische Anwendungen im Maschinen‑ und Metallbau ab. Die Länge bietet ein ausgewogenes Verhältnis aus Reichweite und Steifigkeit, ideal für Bauteile, Spannmittel und Serienteile. Anwender profitieren von konsistenten Ergebnissen bei Prüfplänen und Werkstattmessungen. Integration in digitale Abläufe und einfache Ablesbarkeit Die Digitalanzeige mit einer Höhe von 11 mm sorgt für schnelle, sichere Ablesung auch bei feinen Teileschreibungen. Der wireless Datenausgang ermöglicht die direkte Übertragung in Prüfsoftware oder Messdatenerfassungssysteme und erleichtert so die Datendokumentation im Sinne von Industrie 4.0. Dadurch lassen sich Messprotokolle automatisieren und Fehlerquellen durch manuelle Übertragung vermeiden. Für verlässliche Serienmessungen empfiehlt sich der Erwerb des Präzisionsmessschiebers von Microtech Metrology über Metav Werkzeuge; bei fachlichen Fragen steht die Beratung per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 zur Verfügung Produktmerkmale Artikelnummer: 141072392C Marke: Microtech Metrology Bezeichnung: Präzisionsmessschieber GTIN: 4061905200663 Fakten Messbereich: 0-300 mm Auflösung: 0,01 mm Displayhöhe: 11 mm Ablesung: 0,01 Besonderheiten Datenausgang: wireless (für Datenübertragung) Handgefertigte Messbacken Tiefenmaß Digitalanzeige ISO 17025 Kalibrierung: Kalibrierzeugnis mitgeliefert Messflächen: vorhanden Schnabellänge: 60/21 FAQ Welche Auflösung hat das Messgerät und wie genau ist es? Der Präzisionsmessschieber von Microtech Metrology bietet eine Auflösung von 0,01 mm; für den Messbereich bis 300 mm ist eine Fehlergrenze von etwa ±0,03 mm typisch, was ihn für Standard‑Qualitätskontrollen im Maschinenbau qualifiziert. Wird das Gerät kalibriert geliefert? Ja, der Präzisionsmessschieber wird vollständig kalibriert geliefert und enthält ein ISO 17025 konformes Kalibrierzeugnis, sodass die Prüfmittelverwaltung sofort dokumentierbare Werte erhält. Wie werden Messergebnisse übertragen? Die Schieblehre verfügt über einen wireless Datenausgang, der eine direkte Übertragung von Messwerten in Datenlogger oder Prüfsoftware ermöglicht und so manuelle Übertragungsfehler minimiert. Für welche Anwendungen eignet sich das Messwerkzeug besonders? Das Instrument ist ideal für Werkstatt‑ und Fertigungs‑Kontrollen, Serienprüfungen im Maschinenbau und für die Qualitätskontrolle von Präzisionsteilen bis 300 mm, dank robuster Bauweise und präziser Messbacken. Welche Vorteile bieten die handgefertigten Messbacken? Handgefertigte Messbacken sorgen für exakte Anlegeflächen und längere Standzeit bei wiederholten Messungen, was die Reproduzierbarkeit von Messwerten in Fertigungsprozessen verbessert. Hersteller: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine; tool@microtech.tools
15mm Inner Measuring Insert Flat 5×0.6mm Tips L25 For Digital Precision Caliper, Stainless Steel - Metav IndustryLine
Take advantage of the combination of flat measuring face geometry and stainless steel durability to measure narrow grooves reliably from 15 mm; the compact profile and light weight ensure quick mounting on compatible digital calipers. Order the insert directly via Metav Werkzeuge or consult the Metav team for compatibility advice. Metav IndustryLine M240.213 internal measuring insert — flat 5 x 0.6 mm, L = 25, from 15 mm The M240.213 internal measuring insert for Digital Uni Calipers series 240.201–240.205 extends internal measuring capability from 15 mm, offering precise groove and notch measurement in confined spaces. Flat measuring face 5 x 0.6 mm for narrow grooves For internal measurements starting at 15 mm Stainless steel construction for corrosion resistance Precise groove measurement in compact spaces The insert’s flat measuring face (5 x 0.6 mm) and short jaw length L = 25 mm were developed specifically for narrow groove and slot inspection. The slim contact geometry concentrates the measuring edge without enlarging the profile, which reduces the risk of interfering with neighbouring features; this results in more reproducible internal readings when used with a compatible digital caliper. The component’s form is particularly beneficial for quality control tasks where access is limited and repeatability is essential, such as assembly checks and finishing inspections. Robust, lightweight construction for reliable handling Made from stainless steel, the insert combines corrosion resistance with dimensional stability. At a weight of 0.04 kg, the accessory adds minimal mass to the caliper, maintaining the instrument’s balance and ease of use during repetitive measurement cycles. The durable material reduces maintenance needs and prolongs service life in workshop environments, while the compact design supports fast tool changes and secure clamping on the caliper jaw, improving throughput in routine inspection processes. Compatibility and practical application in production Designed for direct installation on the Digital Uni Calipers series 240.201–240.205, the insert enables internal measurements starting at 15 mm, making it suitable for groove, notch and small-diameter internal checks. The flat measuring surface improves contact on step-like geometries and prevents rocking that can occur with rounded jaws. In machining, toolroom and maintenance settings, the insert provides a pragmatic extension of a caliper’s functionality, reducing the need for separate specialised gauges and supporting faster in-process decisions. For advice on fitment and to procure the Metav IndustryLine M240.213 insert from Emmerich, contact Metav Werkzeuge at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: M240.213 GTIN: 4061905053702 Material: stainless steel Weight: 0.04 kg Length: 50 mm Facts Measuring face: 5 x 0.6 mm Measuring jaw length: L = 25 mm Internal measurement from 15 mm Suitable for groove and notch measurements Special features Compatible with Digital Uni Calipers series 240.201–240.205 Flat measuring surface for narrow grooves Lightweight design for easy handling FAQ What tasks is the insert intended for? The Metav IndustryLine M240.213 internal measuring insert is intended for narrow groove, notch and small internal-diameter measurements beginning at 15 mm when fitted to Digital Uni Calipers series 240.201–240.205. Is the insert resistant to corrosion? Yes. The measuring insert is manufactured from stainless steel, providing corrosion resistance and stable performance in workshop and production environments. Will the insert affect caliper handling significantly? No. At 0.04 kg the accessory is lightweight and maintains the caliper’s balance, enabling reliable manual handling during repetitive inspection sequences. Can the insert be used for step and slot checks? Yes. The flat 5 x 0.6 mm measuring face and 25 mm jaw length are optimised for step-like geometries, narrow slots and grooves where a slim contact area improves measurement repeatability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
18mm Digital Precision Caliper Set 18-Piece, Compatible With Digital Calipers - TECWERK
Take advantage of a compact 18-piece measurement set that supplements a digital caliper for standard workshop checks; the combination of compatibility and organised components streamlines inspection routines. Order the measurement set directly via Metav Werkzeuge or ask our consultants for matching technical information. TECWERK 18-piece Measurement Set for Digital Calipers The TECWERK 18-piece measurement set is a compact kit designed to complement a digital caliper for routine workshop measurements and inspection tasks. 18-piece set tailored for digital calipers Compact organisation for workshop use Precision components for repeatable checks Suitable for general measurement tasks Improve inspection speed with targeted accessories The 18-piece kit extends the functionality of a digital caliper by providing a concise collection of measurement aids that make common checks faster and more consistent. Rather than assembling ad hoc tools, the set supplies a defined set of items that supports standardised measuring routines; this reduces the need for improvisation and helps maintain consistent measurement conditions across repeated checks. The result is more efficient throughput in day-to-day workshop tasks and a clearer audit trail for quality records. Consistent results through simplified measuring workflows Using a dedicated measurement kit promotes repeatable checks and straightforward procedures. The organised grouping of components allows for quick selection and reduces handling time during inspections. For teams carrying out frequent dimensional verifications, this approach lowers the likelihood of operator-induced variation and supports a reliable process for incoming inspection, maintenance verifications or routine quality control. The emphasis is on functional reliability rather than superfluous complexity. Practical applications across workshop and service environments This measurement kit is aimed at technicians and maintenance staff who routinely use a digital caliper for mechanical checks. Typical applications include verifying part dimensions, comparing sample parts against drawings, and performing basic in-process checks. The set is intended for general workshop measurement needs and suits environments where straightforward, repeatable measurements are required without specialist laboratory equipment. Further information and compatibility guidance If additional technical data is required to confirm suitability for specific tasks or measurement standards, further details can be provided on request. The set is presented as a complement to digital calipers and is described to clarify compatibility and practical use rather than to replace calibration or traceable measurement equipment where legal metrology or certified results are required. For clarifications on intended applications or to request supplementary specifications, the standard contact channels are available. Contact Metav Werkzeuge to request matching technical data for the TECWERK 18-piece measurement set and to confirm compatibility with existing digital calipers via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: 2000851028NW SKU: 2000851028NW UID: 2000851028NW Facts Content: 18 pieces Packaging unit: 1 Special features Product type: Measurement set Brand: TECWERK Addition: suited to digital calipers FAQ What does the set contain? The TECWERK 18-piece measurement set contains a coordinated group of measurement aids intended to supplement a digital caliper for common workshop checks. Is the set compatible with all digital calipers? The set is described as suited to digital calipers; compatibility depends on the caliper design and measuring task, so compatibility with specific models should be checked against the caliper in use. Can this kit be used for quality control documentation? The measurement set supports repeatable workshop checks and can form part of routine quality control procedures; traceable certification or calibration must be handled separately if required. Is the kit suitable for mobile fieldwork? The set is intended for practical workshop and service applications and can be employed in mobile inspection tasks where standardised, repeatable measurements are needed. Manufacturer / Responsible: NORDWEST Handel AG, Robert-Schuman-Straße 17, 44263 Dortmund
20 mm Bore Distance Measuring Insert 60° Length 70 mm, For Caliper Adapter - Metav IndustryLine
Compact, precise and workshop-ready: the insert for 20 mm bore spacing at 60° with a 70 mm insertion length enables reproducible checks of hole patterns and straightforward adapter fitment — order the component via Metav Werkzeuge or consult our specialists for compatibility. Bore-spacing measuring insert 20 mm — measuring insert for caliper adapter, 60°, 70 mm length (Metav IndustryLine) Bore-spacing measuring insert 20 mm for caliper adapter — a compact metrology accessory tailored to check hole centres and angular offsets on small assemblies with a rigid 70 mm reach For Ø20 mm bore spacing at 60° 70 mm insertion length for extended reach Ø5 mounting shank for standard adapters Lightweight 0.05 kg for easy handling Reproducible bore-centre checks for small assemblies This measuring insert turns a standard caliper adapter into a dedicated tool for verifying 20 mm bore spacing at 60°, providing a quick and repeatable method to confirm hole patterns without bespoke fixtures. The accessory is designed for straightforward alignment with an adapter, so typical inspection tasks in quality control or assembly become more efficient. By avoiding improvised gauging solutions, production checks gain in repeatability and throughput, while measurement uncertainty is reduced through consistent mechanical fit. Compact design that reaches where it matters With a 70 mm insertion length and an Ø5 mounting shank, the component offers access into recesses and across small assemblies while remaining simple to handle. The modest mass (0.05 kg) contributes to easy mounting and minimal loading on the caliper adapter, keeping the measuring chain stable during manual checks. The compact form factor is especially useful in bench-level inspections and during set-up of jigs where a slim, rigid probe is preferable to larger instruments. Practical fitment and workshop applications Suited for use with caliper adapters that accept an Ø5 shank, this insert is a practical addition for workshops and inspection benches that perform repeated hole-centre verifications. Typical applications include component incoming inspection, prototype checks and fast in-line spot checks where a dedicated gauge would be impractical. Metav IndustryLine supplies this accessory as part of a broader range that aims to make high-quality metrology accessible for the workshop environment, supporting reliable supply and transparent order handling from Emmerich. Contact Metav Werkzeuge to confirm adapter compatibility or to request delivery from our Emmerich warehouse; our specialists will advise on integration and availability Technical information Article number: M240.324 GTIN: 4054469159560 ECLASS: 21170324 SKU: M240.324 Core data Length: 70 mm Weight: 0.05 kg Mounting diameter: Ø5 Analog: yes Special features For Ø20 mm bore spacing at 60° For caliper adapter (20 mm) Category: Measuring devices / Accessories Tariff number: 90178090 FAQ What bore spacing and angle does the insert check? The insert is designed for a 20 mm bore spacing at 60°, enabling direct verification of that hole pattern. Which mounting interface is required for use with adapters? The component uses an Ø5 mounting shank and is intended for caliper adapters that accept that diameter. Is the insert suitable for handheld caliper inspections? Yes — the lightweight design (0.05 kg) and 70 mm reach make it appropriate for bench and handheld checks when used with a compatible adapter. Can this insert be used with analogue calipers? The accessory is compatible with caliper adapters for analogue and digital calipers, provided the adapter accepts an Ø5 shank and the caliper provides stable seating. What is the article number or SKU for ordering? The article number and SKU is M240.324 for ordering and stock reference. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200 mm Digital Caliper IP67, Automatic Shut-Off, 0.01 mm Resolution, Four-Point Measurement, Stainless Hardened Steel, Supplied in Case - Metav IndustryLine
Take advantage of a robust, workshop‑ready tool that combines a 200 mm measuring range with IP67 protection and a hardened stainless‑steel construction to ensure reliable routine checks; order directly via Metav Werkzeuge or consult our specialists for detailed application advice. Digital caliper M216.162.D — 200 mm precision caliper with IP67 protection (Metav IndustryLine) The Digital caliper M216.162.D is a 200 mm precision measuring instrument, engineered for standard workshop and quality‑control tasks in accordance with DIN 862, offering fast digital readings and durable handling for everyday industrial use. 200 mm measuring range, DIN 862 compliant IP67 dust and water resistant Hardened stainless‑steel construction Digital readout 0.01 mm resolution Consistent accuracy for workshop and inspection routines The instrument is designed as a standard‑range caliper (measuring range up to 200 mm), which provides the ideal compromise between reach and stiffness for general machine‑shop and metalworking applications. With a display resolution of 0.01 mm and an accuracy of ±0.03 mm, the device supports reliable dimensional checks to the expectations of production control; compliance with DIN 862 gives a clear normative basis for acceptance in inspection protocols. The compact form factor and ergonomic jaw geometry make repeated checks efficient and reproducible, reducing cycle time in routine quality tasks. Built to withstand industrial conditions Constructed from hardened stainless‑steel, the caliper resists wear and maintains jaw geometry under frequent use, while the IP67 ingress rating protects the electronics from dust and immersion, extending service life in harsher shop environments. The moderate mass (0.4 kg) balances stability with easy handling, and the robust finish helps prevent corrosion in mixed‑material workshops. These attributes translate into lower downtime and fewer tool replacements, supporting steady production throughput. Fast digital workflow and four‑way measurement capability The calibrated digital display features practical controls (including INC, NODE and HOLD) for immediate readings and repeatable settings; the unit runs on a 3 V CR2032 battery and includes automatic switch‑off to preserve power during intermittent use. The caliper supports inside, outside, depth and step measurements, making it a versatile instrument for component inspection, fixture set‑up and quick verification tasks. The clear readout and simple operation reduce operator error and speed decision‑making at the inspection bench. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine caliper with IP67 protection can be integrated into your quality workflow and to request tailored advice from our specialists. Technical data Article number: M216.162.D GTIN: 4054469182926 Manufacturer: Metav IndustryLine Key figures Measuring range: 0–200 mm Resolution: 0.01 mm Accuracy: ±0.03 mm Weight: 0.4 kg Jaw length: 50 mm Battery: 3 V CR2032 Protection class: IP67 Standard: DIN 862 Materials & features Hardened stainless‑steel construction Digital display with INC, NODE, HOLD and ON/OFF controls Automatic switch‑off function Four‑way measurement: inside, outside, depth and step measurements FAQ Is this caliper suitable for everyday workshop use? The M216.162.D from Metav IndustryLine is intended for standard workshop and inspection tasks, offering a 200 mm range and robustness suited to routine production checks. What measurement modes are available with this caliper? The instrument supports inside, outside, depth and step measurements, enabling versatile use across common inspection scenarios. How precise is the digital display? The digital display provides a resolution of 0.01 mm with an overall accuracy of approximately ±0.03 mm within the 0–200 mm range, consistent with standard digital caliper performance. How is the caliper powered and what about battery life? The caliper uses a 3 V CR2032 battery; the automatic switch‑off feature helps to extend battery life during intermittent use. Does the construction withstand workshop conditions like coolant splash or dust? Yes, the caliper features a hardened stainless‑steel body and an IP67 rating, offering resistance to dust ingress and temporary immersion, which is beneficial in demanding workshop environments. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200 mm Digital Caliper, ABS Display, 0.01 mm Resolution, Stainless Scale, Four-Function Measurement, Supplied in Case - Metav IndustryLine
Benefit from precise, repeatable shop‑floor measurement thanks to the combination of an absolute measuring system (3 V), 0.01 mm display resolution and a removable thumb roller that speeds up linear feeds; order the caliper directly via Metav Werkzeuge or consult our specialists for application advice. Digital Caliper M216.236.N — 200 mm absolute caliper with removable thumb roller (Metav IndustryLine) The Digital Caliper M216.236.N is a 200 mm absolute digital caliper designed for standard workshop and machine‑shop measurement tasks, featuring a removable thumb roller for smooth, repeatable operation. Absolute measurement system with 0.01 mm resolution Removable thumb roller for fast, repeatable feeds Hardened stainless steel with glass scale for durability Delivered in transport case for protected storage High‑precision readings for reliable quality control The caliper combines an absolute measuring system with a standard 0.01 mm display step, making it suitable for routine dimensional checks in metalworking and quality control. For a 200 mm instrument, this configuration aligns with typical industrial tolerances for digital calipers and supports consistent reproducibility across batch inspections. The DIN 862 compliance underlines its conformity with recognised mechanical caliper standards, so users receive traceable, comparable results on components and assemblies. Faster measurement cycles and seamless data capture Equipped with an intuitive digital display and dedicated keys (ORIGIN, UNIT, ON/OFF and 0/ABS), the instrument keeps setup simple while the RB 5 data output allows for direct transfer of measured values into process documentation or inspection software. The removable thumb roller and slim jaw design (jaw lengths 50/24 mm) enable quicker linear advances and ergonomic single‑handed operation, reducing cycle time when performing repeated outside, inside, depth and step measurements. Robust construction and workshop readiness Constructed from hardened stainless steel with a glass scale slide, the caliper resists wear and maintains measuring integrity in a demanding shop environment. Weighing approximately 0.48 kg and supplied in a protective transport case, the unit is built for everyday use and safe handling between workstations. The combination of durable materials and an absolute encoder that preserves the origin after power‑off ensures dependable performance during production routines. Metav’s role as a quality filter for the European market adds assurance that the tool is selected for reliability and practical suitability. Choose the Metav IndustryLine caliper for dependable, shop‑ready precision and contact Metav Werkzeuge for tailored technical advice or guidance on integrating this caliper into existing measurement workflows. Technical Data Article number: M216.236.N GTIN: 4054469159362 Weight: 0.48 kg Standard: DIN 862 Measuring range: 0–200 mm Resolution: 0.01 mm / 0.0005 in Measuring system: Absolute (3 V) Data output: RB 5 Key figures Jaw length: 50/24 mm Display functions: ORIGIN, UNIT, ON/OFF, 0/ABS Measurement types: inside, outside, depth, step Delivered in transport case Special features Material: hardened stainless steel, scale with glass slide Removable thumb roller for controlled feeds Digital display with absolute zero retention Suitable for routine workshop and machine‑shop inspection FAQ Is the caliper suitable for standard machine‑shop quality control? The Digital Caliper M216.236.N meets DIN 862 and, with its 0.01 mm resolution and absolute measuring system, is well suited for routine quality checks and dimensional inspections in a machine‑shop environment. Can measured values be exported to inspection software? Yes. The instrument provides an RB 5 data output for direct value transfer, simplifying documentation and data logging for the Digital Caliper M216.236.N. What measurement modes are supported? The caliper supports four measurement modes — inside, outside, depth and step — enabling versatile use across common workshop tasks. Is the thumb roller fixed or removable? The thumb roller is removable, allowing users to switch between fine manual adjustment and rapid feeding depending on the measurement task and operator preference. What protection and handling does the delivery include? The caliper is supplied in a protective transport case, ensuring secure storage and safe transfer between workstations. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
2000mm Data Cable DIGI-MET With Variable Digimatic Output And Data Transfer Button - HELIOS-PREISSER
Take advantage of the combination of reliable Digimatic connectivity, a variable data output and a 2 m cable length for uninterrupted measurement transfer; order the DIGI‑MET data cable directly via Metav Werkzeuge or ask the consultants for tailored integration advice. DIGI‑MET data cable – Digimatic interface, variable output, 2 m (Helios‑Preisser) DIGI‑MET data cable for direct connection of digital measuring instruments, configured for DIGI‑MET® systems with a variable data output and an integrated transfer control Compatible with Digimatic interfaces Variable data output for flexible systems 2 m cable length for extended reach Transfer button for controlled data transmission Reliable interface for industrial metrology systems The cable provides a Digimatic interface tailored for industrial metrology and workshop measurement devices, enabling straightforward integration into established data collection setups. With the variable data output, the lead adapts to differing data acquisition requirements and permits selection of the most suitable signal type for the connected equipment. This compatibility reduces setup time and minimises the need for adapters, supporting efficient measurement workflows and consistent data capture. Controlled data transfer and operational ease An integrated transfer button allows explicit, operator-controlled transmission of measured values, preventing unwanted data entries during adjustments. The 2 m length offers practical reach for bench-mounted calipers and measuring stands without excess cable clutter, supporting tidy workstations and smoother production processes. Clear tactile feedback from the button enhances repeatable handling when recording individual readings. Robust design for dependable signal integrity Engineered for measurement environments, the cable construction prioritises signal integrity and reliable contact under frequent use. The combination of a dedicated Digimatic connection and attention to contact quality helps maintain accurate transmission of numeric values from digital measuring devices to data loggers or PCs. This reduces rework caused by transmission errors and supports a more predictable quality control routine. Straightforward integration and documentation benefits Specified for DIGI‑MET® execution, the lead simplifies system documentation and procurement by matching a common interface standard used across many precision instruments. Where traceability and process documentation are required, the predictable behaviour of the Digimatic connection and the option to choose a suitable output type support automated data capture chains and reduce manual transcription effort, streamlining quality assurance tasks. Contact Metav Werkzeuge to request the Helios‑Preisser DIGI‑MET data cable and receive expert advice on system integration; email info@metav-werkzeuge.com or call +49 2822 7131930. Technical data Article number: 4000851609NW Type: DIGI-MET Product: Data cable Brand: Helios-Preisser Length: 2 m Data output: Digimatic Packaging unit: 1 Facts Cable length: 2 m Packaging unit: 1 Special features For digital measuring instruments For DIGI‑MET® execution Variable data output Data transfer button FAQ Is this cable compatible with Digimatic ports on calipers and indicators? The DIGI‑MET data cable by Helios‑Preisser is designed for Digimatic interfaces and is suitable for most digital calipers and indicators that use the Digimatic protocol. Can the cable be used with different data acquisition systems? Yes, the variable data output supports flexible connections; the DIGI‑MET lead can be adapted to common data collection setups when the receiving system accepts Digimatic signals or equivalent configured outputs. What does the transfer button do on the cable? The transfer button sends the current reading from the connected digital measuring device when pressed, enabling controlled and deliberate data capture without relying on automatic transmission. Is the 2 m length suitable for bench workstations? The 2 m cable length offers extended reach suitable for bench-mounted measurement tasks while avoiding excessive cable routing across the workstation. What is the exact article number for ordering and documentation? Order and reference using article number 4000851609NW for the Helios‑Preisser DIGI‑MET data cable Manufacturer / Responsible: Mahr GmbH Helios-Preisser Vertrieb; Ölbergstraße 19; 72501 Gammertingen; Germany; +49 7574 400-60
2000mm Data Cable DIGI‑MET USB Variable Data Output With Transfer Button, USB - HELIOS-PREISSER
Take advantage of the combination of precise data capture, flexible output options and included Excel import software to streamline measurement workflows; order the DIGI‑MET USB data cable directly via Metav Werkzeuge or consult Metav's specialists for integration advice. DIGI‑MET USB data cable — USB connection with variable output and 2 m length (Helios Preisser) DIGI‑MET USB data cable for quick data transfer from digital measuring instruments to PC systems, designed for DIGI‑MET versions and workshop environments For digital measuring instruments Variable data output selection Data transfer button for instant logging Includes Excel import software Faster, more reliable measurement logging for production use The DIGI‑MET USB data cable provides a direct, wired USB connection that removes manual re‑entry and reduces transcription errors. With a data transfer button, individual readings can be captured on demand, which supports traceable measurement workflows and shortens processing time. The combination of a wired interface and immediate transfer capability helps maintain data integrity during batch measurements and repetitive quality checks, ensuring consistent documentation across shifts. Seamless integration with spreadsheets and measurement software Included software enables straightforward data import into Excel, so recorded values are immediately usable for analysis, reporting or SPC (statistical process control). The cable's variable data output means the lead can adapt to different output formats used by common digital gauges; this allows compatibility with various measurement setups without additional converters. For customers less familiar with interface formats, variable data output denotes selectable output modes rather than a fixed protocol, simplifying system alignment and reducing configuration time. Workshop‑ready design that improves day‑to‑day efficiency A 2 m cable length balances reach and tidiness at the bench, providing enough freedom to position instruments without trailing cables across the work area. The lead is intended for DIGI‑MET versions of digital measuring devices and supports consistent signal transmission for uninterrupted data capture. Integration of the cable into routine measuring tasks reduces handling, minimises interruption to production and supports faster throughput — a pragmatic solution for workshops seeking to accelerate measurement cycles while preserving accuracy. Contact Metav Werkzeuge for tailored advice on integrating DIGI‑MET USB data cables into existing measurement setups and for procurement from a reliable European supplier based in Emmerich. Technical data Article number: 4000 851 632 SKU: 4000851632NW Type: DIGI‑MET Product: Data cable Label: DIGI‑MET USB data cable with variable data output, 2 m, Helios Preisser Packaging unit: 1 Facts Length: 2 m Data output: USB Packaging unit: 1 Special features For digital measuring instruments For DIGI‑MET version Variable data output Data transfer button Includes software for Excel import FAQ How does the variable data output work in practice? The variable data output lets the DIGI‑MET USB data cable switch between supported output modes so recorded values match the receiving application’s expected format, avoiding manual conversion. Is software for Excel included and ready to use? Yes, the package includes software for data import directly into Excel, enabling immediate transfer of readings from the DIGI‑MET cable into spreadsheets for analysis. Can this cable be used with any digital gauge? The cable is designed for DIGI‑MET versions of digital measuring instruments; compatibility with non‑DIGI‑MET gauges depends on the instrument’s output protocol and may require configuration. What is the usable reach at the workbench? The connection lead provides a 2 m length, offering practical reach for most bench setups without excessive cable slack. Does the cable support one‑shot capture of readings? Yes, the integrated data transfer button permits single‑press capture of individual measurements for precise logging and reduced operator steps. Manufacturer / Responsible: Mahr GmbH Helios-Preisser Vertrieb; Ölbergstraße 19; 72501 Gammertingen; Germany; +49 7574 400-60
2000mm Data Cable RS232 Variable Data Output With Transfer Button - HELIOS-PREISSER
Take advantage of reliable serial communication, an RS232 interface and a dedicated data-transfer control for streamlined measurement logging; order the connection lead directly via Metav Werkzeuge or consult our specialists for integration advice. DIGI‑MET RS232 data cable — 2 m, variable data output (Helios‑Preisser) DIGI‑MET RS232 data cable for connecting digital measuring instruments in DIGI‑MET configuration with RS232 output and an integrated data-transfer button, designed for workshop and inspection environments For digital measuring instruments (DIGI‑MET®) RS232 interface with variable data output Integrated data transfer button for controlled send 2 m cable length for flexible installation Stable serial communication that supports traceable measurement workflows The connection lead provides a consistent RS232 link between measuring devices and documentation systems, ensuring measured values arrive intact and in the correct order. Serial transmission is a long-established standard for industrial metrology; the variable data output feature means the cable supports configurable data streams from compatible devices, enabling flexible integration with data loggers, PCs or PLC interfaces. This reliability reduces repeat measurements and supports audit trails in quality-controlled environments. Controlled sending for fewer transcription errors and faster logging An integrated data transfer button allows deliberate transmission of readings, avoiding accidental or partial transfers during setup or repositioning. When used with DIGI‑MET®‑configured instruments, the cable assists in creating a predictable handover of results to connected systems, which speeds up documentation and reduces manual correction. The ability to adapt the output format through the device’s settings complements the cable’s function, so workflows become both efficient and less error-prone. Practical length and compatibility for shop-floor deployment The 2 m lead provides reach without excess clutter, making it suitable for benches, height gauges and mobile inspection rigs. The cable is supplied as a single unit, ready to connect to any compatible RS232 interface on digital measuring instruments, simplifying installation and lowering setup time. For users requiring further technical compatibility details or integration examples, additional configuration guidance is available to ensure seamless connection between measurement tools and downstream systems. Contact Metav Werkzeuge for supply and technical configuration of Helios‑Preisser DIGI‑MET RS232 cables — our Emmerich team provides practical advice and reliable delivery for workshop and industrial use Technical data Article number: 4000851603NW Product type: Data cable Label: Datenkabel DIGI-MET RS232 z.Data-Variable L.2m H.PREISSER UID: 4000851603NW Manufacturer: HELIOS-PREISSER Packaging unit: 1 Facts Length: 2,000 mm (2 m) Data output: RS232 Packaging unit: 1 Special features For digital measuring instruments (DIGI‑MET®) Variable data output Integrated data transfer button RS232 data output FAQ How does the RS232 connection affect measurement logging? The RS232 interface provides a standardised serial link; the DIGI‑MET RS232 data cable allows measured values to be transmitted directly from the measuring device to recording systems for consistent logging. Can the cable be used with different DIGI‑MET devices? Yes, the DIGI‑MET RS232 data cable is intended for DIGI‑MET®‑configured digital measuring instruments and supports the variable data output modes those devices provide. What advantage does the data transfer button offer? The integrated data transfer button on the cable enables controlled sending of readings, helping to prevent accidental transfers and reducing transcription errors during documentation. Is the 2 m length suitable for workshop use? The 2 m length gives practical reach for bench and mobile inspection setups while keeping cabling manageable for routine workshop deployment. Manufacturer / Responsible: Mahr GmbH Helios-Preisser Vertrieb; Ölbergstraße 19; 72501 Gammertingen; Germany; +49 7574 400-60
200mm Digital Absolute Precision Caliper With mm/inch, ABS/INC, Depth Gauge, Locking Screw, CR2032 Battery - Filetta
Compact, workshop-ready measuring performance with a 0–200 mm range and ±0.03 mm accuracy combined with a clear digital readout and a protective case for safe storage — order directly via Metav Werkzeuge or consult our specialists for application advice. Filetta MS910.469 digital caliper — 0–200 mm range, 0.03 mm accuracy The Filetta MS910.469 digital caliper is a robust measuring instrument for standard workshop and engineering tasks, engineered for precise outside, inside and depth measurements in metalworking and general assembly. 0–200 mm measuring range Resolution 0.01 mm, accuracy 0.03 mm Depth gauge and 50 mm jaw length Supplied in protective case with CR2032 battery Precise results for everyday workshop demands The MS910.469 is classified in the Standard measuring-range group (up to 300 mm), offering the typical balance of reach and rigidity required in machine shops and metalworking departments. With a resolution of 0.01 mm and an indicated accuracy of ±0.03 mm, the instrument supports reliable dimensional checks on shafts, housings and finished parts. The digital display shows readings in mm/inch and provides ABS/INC switching plus a reset function, reducing reading errors and speeding throughput on repetitive tasks. The thumbwheel drive enables fine, controlled movement while the locking screw secures measurements for transfer or recording. Built to reduce handling errors and speed inspection Engineered features such as the integrated depth gauge, 50 mm jaw length and the driven thumbwheel focus on repeatable operation and ease of use under production conditions. The caliper’s display modes and reset function help to avoid conversion mistakes between metric and imperial units, supporting faster decision-making on the shop floor. Where traceable checks are essential, the device’s consistent mechanical behaviour and clear readout contribute to lower scrap rates and fewer reworks, offering measurable efficiency gains in quality-control workflows. Robust storage and simple field service The instrument is supplied in a protective case and includes a ready-to-use CR2032 battery, simplifying delivery and first-use handling. The compact case protects the caliper during transport and on-site storage, ensuring the measuring faces and electronics remain intact between operations. Maintenance consists of routine cleaning of the guides and replacement of the battery when required; the straightforward construction avoids complex service needs, making this caliper a practical choice for workshops seeking dependable everyday precision. For application guidance or to secure the Filetta MS910.469 through Metav Werkzeuge, contact the Emmerich team by phone or email for prompt, workshop-focused assistance and ordering support Technical data Article number: MS910.469 Brand: Filetta Type: Digital caliper Measuring range: 0–200 mm Resolution: 0.01 mm Accuracy: ±0.03 mm Display: mm/inch, ABS/INC, reset Battery: 1x CR2032 Jaw length: 50 mm Depth measurement: yes Thumbwheel drive: yes Locking screw: yes Supplied in protective case: yes Facts Measuring range: 0–200 mm Resolution: 0.01 mm Accuracy: 0.03 mm Jaw length: 50 mm Battery type: CR2032 Special features Digital readout with mm/inch conversion ABS/INC and reset functions Depth-gauge measurement Thumbwheel for fine adjustment Locking screw for repeatable readings Supplied in protective case with battery FAQ Is the caliper suitable for general machine-shop use? The Filetta MS910.469 digital caliper is designed for standard machine-shop and metalworking tasks, offering a 0–200 mm range and accuracy suited to workshop QC and assembly measurements. What measurement types are possible with this caliper? The instrument supports outside, inside and depth measurements; the depth gauge and the 50 mm jaw length enable a wide range of common inspection tasks. How precise are the readings shown on the display? Readings present at 0.01 mm resolution with an indicated accuracy of ±0.03 mm, making the caliper appropriate for routine precision checks where this tolerance meets specification. Is a protective case supplied and is the caliper ready to use? Yes, the caliper is supplied in a protective case and includes a fitted CR2032 battery for immediate use. Does the caliper offer metric and imperial units? The digital display switches between mm and inch and includes ABS/INC and reset functions to simplify unit conversions and zero-setting. Manufacturer / Responsible: Schut Geometrische Meettechniek bv; Duinkerkenstraat 21; 9723 BN Groningen; The Netherlands; +31 50 5877877; schutnl@schut.com
200mm Digital Caliper 0.01mm Readout With Fractional 1/128" Display, Stainless Hardened, Supplied In Case - Metav IndustryLine
Combine hardened stainless-steel construction, 0.01 mm resolution and four‑way measurement for reliable workshop control and repeatable results; order the caliper directly via Metav Werkzeuge or consult the Metav team for application advice. Digital Caliper M216.062 (200 mm / 8'') – Fractional 1/128", RB 2 The Digital Caliper M216.062 is a standard‑range digital caliper for workshop and machine‑tool measurement, providing metric and fractional inch readouts and a compact, hardened design suitable for routine quality checks. Resolution 0.01 mm digital display Fractional readout 1/128" mode Hardened stainless‑steel construction Four‑way measurement capability Supplied in protective transport case Precise numeric feedback for routine quality control The electronic display offers a fine 0.01 mm step, with inch resolution of 0.0005" / 1/128", enabling fast, unambiguous readings for pass/fail checks and documented inspections. The integrated mm/inch switch and the zeroing function simplify comparative measurements against templates or gauges, while the fractional mode supports traditional drawing references. This measurable accuracy reduces rework by clarifying tolerances at the point of measurement. Robust workshop design with standard‑range benefits Classified in the standard range for its 200 mm reach, the instrument balances reach and stiffness for everyday metalworking tasks. The body is made from hardened stainless steel, providing corrosion resistance and long service life in workshop environments. The caliper supports internal, external, depth and step measuring thanks to its four‑way capability, and the jaw geometry (jaw length 50/24 mm) remains stable under normal handling. Supplied in a protective case, it is prepared for safe transport between workstations. Data handling and integration to speed up workflows Equipped with an interface labelled RB 2, the device facilitates data transfer to documentation systems and reducing manual transcription. The display includes on/off, zero and mm/inch keys for quick operation during batch inspection. As part of the Metav IndustryLine, the caliper M216.062 is positioned for dependable workshop integration, offering a pragmatic balance of measurement clarity and connectivity that supports efficient production control. Contact Metav Werkzeuge for a technical match to specific workflows or to arrange procurement from Metav IndustryLine; email info@metav-werkzeuge.com or call +49 2822 7131930 for consultancy and delivery details Technical data Article number: M216.062 GTIN: 4054469110196 Eclass: 21170344 Data output: RB 2 Display functions: On/Off, Zero, mm/inch Facts Measuring range: 0–200 mm Resolution: 0.01 mm Inch resolution: 0.0005" or 1/128" Jaw length: 50/24 Tariff number: 90173000 Special features Material: hardened stainless steel Four‑way measurement: internal, external, depth, step Supplied in protective transport case Digital fractional mode (1/128") Workshop‑oriented design for routine inspection FAQ What measurement range does this caliper cover? The caliper covers a measuring range of 0–200 mm, suited to standard workshop tasks and general machine‑building applications. Is the instrument capable of four different measurement types? Yes, the instrument supports internal, external, depth and step measurements thanks to its four‑way measuring design. What data output options are available for documentation? The caliper provides an RB 2 data output interface for transferring readings to documentation systems. Which materials is the caliper made from? The caliper is manufactured from hardened stainless steel, offering corrosion resistance and durability for workshop use. Does the display offer fractional inch readout? Yes, the display includes a fractional inch mode showing 1/128" and a decimal inch representation of 0.0005". Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Digital Caliper 80mm Jaw, M2.5 Thread, Ceramic Insert, Preset, Stainless Steel, With Case - Metav IndustryLine
Reliable measurement in everyday workshop and inspection routines is ensured by the combination of a hardened stainless steel frame, a ceramic measuring insert and an easy preset function for repeatable results; the M2.5 threaded bore for exchangeable heads increases application flexibility. Order directly via Metav Werkzeuge or consult our product specialists for suitability and delivery options. Digital-Uni-MS 200 mm x 80 mm — digital caliper with ceramic insert and preset (Metav IndustryLine) Digital-Uni-MS 200 mm x 80 mm is a compact digital caliper designed for precise internal and external measurements in workshop and quality-control environments Hardened stainless steel construction Ceramic insert for increased wear resistance Digital display with ON/OFF and SET/PRESET controls RB 5 data output for integration and traceability Precision that suits everyday industrial use The instrument addresses the universal workshop requirement for repeatable, verifiable measurements within the Standard range of 0–200 mm, combining practical reach with torsional stiffness. With a display resolution of 0.01 mm and a stated accuracy of ±0.05 mm, the caliper delivers reliable numeric results for machining, assembly and inspection tasks where traceable, comparable values matter. The preset function simplifies repetitive checks by storing a reference position, reducing operator-induced scatter and supporting faster quality-control cycles. The digital readout with dedicated ON/OFF and SET/PRESET keys is designed for clear operation even in busy environments. Robust construction and flexible measuring options Built from hardened stainless steel with a metal housing and fitted with a ceramic insert, the tool resists wear and maintains measuring integrity over long service life; the ceramic contact reduces surface abrasion on delicate or plated parts. Versatility is extended by an integrated M2.5 threaded bore, which accepts exchangeable measuring inserts for special tasks; two 2 mm ball measuring heads are included to support shaft and bore checks out of the box. The 80 mm jaw length provides practical reach on typical components while keeping the instrument easy to handle; net weight of 0.4 kg ensures comfortable one‑hand use with minimal fatigue. Data handling, workflow benefits and traceability Data output via RB 5 permits straightforward transfer of measured values into inspection software or data collectors, improving documentation and reducing transcription errors in quality records. Delivery in a secure transport case protects the caliper during storage and dispatch and supports safe handling between workshop and inspection bench. The combination of robust mechanical design, a wear-resistant contact insert and digital connectivity reduces rework and speeds up inspection loops, delivering measurable efficiency gains across production and service operations. Metav’s distribution and quality filter in Emmerich ensure consistent availability and product reliability. For workshop-ready precision from Metav IndustryLine, contact Metav Werkzeuge GmbH in Emmerich to discuss this digital caliper’s suitability and availability: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M240.206.N GTIN: 4054469160009 Brand: Metav IndustryLine Facts Measuring range: 0–200 mm Resolution: 0.01 mm Accuracy: ±0.05 mm Jaw length: 80 mm Weight: 0.4 kg Supply: 3 V Tariff number: 90173000 Special features Material: hardened stainless steel, metal housing Ceramic measuring insert M2.5 threaded bore for exchangeable measuring inserts Includes two 2 mm ball measuring heads Digital display with ON/OFF and SET/PRESET Data output: RB 5 Delivery in transport case (plastic/wooden) Factory standard: Werksnorm FAQ What measuring range and classification does this caliper cover? The caliper covers a measuring range of 0–200 mm and is classified in the Standard category, offering the best balance of reach and stiffness for general machine‑shop and inspection tasks. How precise and repeatable are the readings? Readout resolution is 0.01 mm with a stated accuracy of ±0.05 mm; the preset function supports repeatable checks and reduces variance from manual setting. Can the caliper be used for both internal and external measurements? Yes, the design supports internal and external measurements and includes two 2 mm ball measuring heads for specialised internal or shaft checks. Are there options for specialised measuring contacts? The instrument features an M2.5 threaded bore for exchangeable measuring inserts, enabling tailored contacts to suit particular workpieces and inspection routines. How can measurement data be exported for documentation? Values can be transmitted via the RB 5 data output to compatible data collectors or inspection software for traceable recording. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Digital Caliper Absolute ABS, 0.01mm Readout, Tolerance LED, IP54, Four‑Function Measurement, Supplied in Case - Metav IndustryLine
Take advantage of the combination of robust IP54 protection, an ABS absolute measuring system and a fast TOL‑LED tolerance indicator for efficient workshop quality control. Order the digital caliper directly via Metav Werkzeuge or ask our consultants if needed. Digital caliper 200 mm, TOL‑LED, ABS absolute system (M216.222) — Metav IndustryLine A digital caliper 200 mm intended for standard workshop inspection and quality control, offering absolute measurement, a visual tolerance LED and splash protection for regular shopfloor use. Absolute measuring system (ABS) with 3 V power TOL‑LED for fast tolerance checks IP54 splash protection for workshop use Four‑function measuring (inside/outside/depth/step) Precise readings that speed up quality checks The instrument delivers a standard digital caliper experience with a resolution of 0.01 mm, meeting the accuracy requirements stated under DIN 862. The ABS absolute system retains the zero position and permits instant readings after power‑on, eliminating routine referencing. Four measurement modes mean the tool covers inside, outside, depth and step checks without accessory changes, reducing handling time and increasing throughput in inspection routines. Robust construction for everyday workshop demands Constructed from stainless steel, hardened for wear resistance, and fitted with a glass‑guided scale, the caliper resists abrasion while maintaining smooth travel. The IP54 rating shields electronics from workshop dust and splashes, making the instrument suitable for machine shops and maintenance benches. The integrated TOL‑LED provides immediate pass/fail indication, so visual sorting is faster and less error‑prone than manual comparison; the display also offers ORIGIN/MODE/HOLD functions for convenient measurement workflows. Ergonomic operation and straightforward integration Powered by a single 3 V cell and featuring a fast response absolute encoder, the device allows continuous movement without a measurement speed limitation, which suits rapid checking cycles. Inch/metric conversion is available with a secondary resolution of 0.0005 in, supporting mixed‑unit environments. Classified in the Standard class (measuring range up to 300 mm), the instrument balances reach and stiffness—ideal for everyday tasks where a 200 mm span is the workshop baseline. Designed for shopfloor and inspection benches alike This caliper blends durability and usability to support repeatable measurements in production, incoming inspection and tool setting. The compact weight and balanced jaw geometry aid single‑handed operation, while the clear display and tolerance signalling lower cognitive load during series checks. Supplied as a reliable Metav IndustryLine tool, the M216.222 complements a broad metrology toolkit and helps maintain consistent process quality across small and medium‑sized operations. Contact Metav Werkzeuge today for personalised advice or to request the M216.222 from our Emmerich stock for rapid delivery and reliable workshop supply Technical data Article number: M216.222 GTIN: 4054469164229 Category: Messschieber / Caliper Manufacturer: Metav IndustryLine Facts Measuring range: 0–200 mm Resolution: 0.01 mm Resolution (inch): 0.0005 in Weight: 0.4 kg Protection class: IP54 Measuring system: Absolute (ABS) with 3 V Special features Material: stainless steel, hardened; scale with glass guide Display functions: ORIGIN, MODE, TOL, HOLD, INC/ON/OFF Tolerance LED (TOL‑LED) for visual pass/fail checks Four‑function measuring: inside, outside, depth, step No measurement speed limitation (continuous measurement possible) FAQ What is the measuring range and resolution of this caliper? The digital caliper offers a measuring range of 0–200 mm with a resolution of 0.01 mm; inch readings are available at 0.0005 in for mixed‑unit tasks. Does the instrument support inside and depth measurements? Yes, the unit performs four‑function measuring — inside, outside, depth and step — so a single tool covers multiple common inspection requirements. How does the TOL‑LED help during series inspection? The TOL‑LED gives an immediate visual pass/fail signal based on preset tolerances, accelerating sorting and reducing interpretation errors during repetitive checks with the M216.222. Is the caliper suitable for workshop environments? The caliper’s IP54 protection, hardened stainless steel construction and glass‑guided scale make it robust enough for regular shopfloor use while maintaining measurement stability. Which features aid quick measurement workflows? The ABS absolute system keeps the zero reference after switch‑off, the device has no measurement speed limitation, and the display includes ORIGIN, MODE and HOLD functions to streamline inspection sequences. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
200mm Digital Caliper Absolute Display 0.02mm Resolution IP54, Four-Point Measurement, Stainless Steel With Glass Slide Kitted - Metav IndustryLine
Take advantage of the combination of workshop-grade robustness, reliable data transfer and fine mechanical precision for consistent measurement results. The 200 mm measuring range, accuracy ±0.02 mm and IP54 protection make this caliper suitable for standard machine‑shop tasks; order the digital caliper directly via Metav Werkzeuge or ask our consultants if needed. Digital Caliper M216.256 — 200 mm absolute caliper with IP54 by Metav IndustryLine The Digital Caliper M216.256 is a 200 mm absolute digital caliper to DIN 862, designed for routine workshop and production measurements where repeatable precision and data output are required. Absolute measuring system with RB 6 data output IP54 protection for dusty and damp environments Four‑function measurement: internal/external/depth/step Stainless steel construction with glass scale Reliable precision for everyday workshop control The caliper delivers accuracy ±0.02 mm with a 0.02 mm reading, a combination that meets typical industrial quality‑control requirements for general mechanical engineering. With a 200 mm measuring range, the instrument falls into the Standard class, offering the best balance between reach and stiffness for routine workpieces such as shafts, housings and fixtures. The specification to DIN 862 provides a trustworthy reference for conformity and comparability in procurement decisions, while the absolute measuring principle avoids the need for repeated reference runs, reducing cycle time during serial checks. Built to withstand workshop conditions and integrate with production data Robustness is a core benefit: an IP54 rating and stainless steel with glass scale construction resist dust and splash exposure common in machining environments, so measurement remains dependable across shifts. The caliper uses an absolute measuring system, which keeps the reference position even after the instrument is powered down, and features data output RB 6 for direct connection to data loggers or statistical process control systems. The digital display includes ON/OFF, 0/ABS, mm/inch and Origin functions for straightforward operation, and a 3 V CR2032 battery powers the unit with a compact supply solution. Versatile handling that speeds up inspection workflows Ergonomic design and manageable mass (approx. 0.5 kg) permit steady one‑handed operation and precise jaw positioning. The device supports four‑function measurement — internal, external, depth and step — allowing a single tool to replace several specialised gauges and thus streamline bench setups. The caliper is operable with or without a drive roller, enhancing adaptability for different measurement techniques. Where traceability and digital logging matter, the integrated output simplifies data capture and reduces transcription errors, supporting lean workflows on the shop floor. Choose the Metav IndustryLine digital caliper M216.256 for robust, workshop-ready measurement and contact Metav Werkzeuge for expert advice or to place an order via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data SKU: M216.256 GTIN: 4054469182568 Label: Digital caliper 200 mm, IP54, DIN 862 Manufacturer: Metav IndustryLine Numbers / Core technical data Measuring range: 0–200 mm Reading / resolution: 0.02 mm Accuracy: ±0.02 mm Weight: 0.5 kg Battery: 3 V CR2032 Protection class: IP54 Special features Material: stainless steel with glass scale Measuring system: absolute Digital display: ON/OFF, 0/ABS, mm/inch, Origin Data output: RB 6 Four‑function measurement: internal, external, depth, step Norm: DIN 862 Operable with or without drive roller FAQ What measurement tasks is this caliper best suited for? This caliper is intended for standard workshop and machine‑shop measurements; the Digital Caliper M216.256 (Metav IndustryLine) covers typical tasks on shafts, housings and assembly parts within its 200 mm range. How does the absolute measuring system help in inspection routines? The absolute measuring system maintains the reference position after power‑off, so the M216.256 avoids repeated zeroing and speeds up serial checks while reducing operator steps. Can measurement results be exported to a PC or data logger? Yes. The caliper provides a data output RB 6 interface that allows direct connection for digital logging and integration into SPC or measurement collection systems. Which measurement functions are supported by the instrument? The tool supports four modes: internal, external, depth and step measurement; these functions make the caliper a versatile choice for diverse inspection needs. Is the caliper suitable for use in a production environment with dust and coolant mist? The IP54 rating and durable stainless steel with glass scale make the Digital Caliper M216.256 suitable for dusty and splash‑prone workshop conditions. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
why digital calipers accelerate accurate measurement
A digital caliper is a precise length-measuring instrument that captures measurements electronically and shows them on an LCD display, making read‑out immediate and error‑free. Compared with analogue calipers it delivers higher accuracy, faster operation and the option to store or transfer measurements, which speeds up inspection and reduces rework. Metav supplies digital calipers from leading manufacturers, ready for industry, workshop and laboratory use.
how digital calipers are used in industrial settings
Digital calipers work by converting linear displacement into an electronic signal via a capacitive sensor, with a clear LCD display and a zero function at any position. Many models allow switching between mm/inch and provide data output for direct integration into measurement systems. Construction in stainless steel and optional protection ratings such as IP54 make them robust enough for shop‑floor tasks. Typical measuring ranges include 0–150 mm and 0–300 mm, covering most component inspection needs.
key performance benefits that improve your workflow
- Rapid, error‑free readings thanks to the LCD display and direct digital output, reducing inspection time.
- Consistent repeatability with a resolution commonly of 0.01 mm, which minimises corrective work.
- Flexible operation with zero at any position and quick conversion between mm/inch, speeding setup and measurement changes.
- Durable design (stainless steel housing, optional IP54) for low maintenance and long service life.
- Seamless data handling where data output is available, enabling faster documentation and process control.
metav industryline and chosen manufacturers as practical options
Metav IndustryLine provides precise, dependable measuring tools designed for everyday use in production and quality assurance. For users seeking cutting‑edge electronics and enhanced connectivity, Microtech offers innovative digital calipers with advanced data features; Filetta supplies robust, economical alternatives for routine workshop tasks. Metav combines its product range with local stock and expertise: more than 48,000 customers trust Metav, and the company offers over 250,000 products from its Emmerich location, acting as a quality filter for the european market.
concise summary
digital calipers deliver fast, repeatable and easily transferable measurements for metalworking, plastics and electronics, with common specifications such as 0.01 mm resolution, 0–150 mm / 0–300 mm ranges and data output options. Metav’s range, including Metav IndustryLine, Microtech and Filetta, covers both high‑precision and cost‑effective needs.
FAQ
what measuring range should i choose for digital calipers?
Choose the measuring range based on the largest dimension you need to check; common options are 0–150 mm for general components and 0–300 mm for larger parts. digital calipers with an appropriate range avoid unnecessary repositioning and speed up inspection.
how precise are digital calipers for repeat measurements?
Digital calipers typically offer a resolution of 0.01 mm and, with a capacitive sensor and solid construction, provide high repeatability suitable for quality control and assembly tasks.
can i connect digital calipers to a pc or measurement system?
Yes. Models with data output support direct transfer of measurements to a pc or data logger, simplifying traceability and statistical process control when used in inspection workflows.
are digital calipers suitable for workshop environments?
Many digital calipers feature a stainless steel housing and protection ratings such as IP54, making them durable enough for the workshop while remaining easy to maintain.
what is the difference between metav industryline, microtech and filetta calipers?
Metav IndustryLine focuses on reliable, well‑manufactured tools for everyday precision; Microtech targets advanced functionality and connectivity for demanding applications; Filetta provides robust, value‑oriented instruments for routine workshop use. Metav packages these choices with local stock and industry expertise from Emmerich.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com