End gauges for precise length calibration
End gauges provide exact reference lengths for calibrating measurement instruments and ensuring consistent dimensional accuracy in metalworking and inspection processes. Used in production and laboratory settings, these end gauges—made from steel, ceramic or carbide—allow technicians to compensate for wear and thermal effects and maintain measurement traceability, especially when employed alongside parallel end gauges, cylinder gauges and calibration masters. Classes 0, 1 and 2 define practical tolerance levels for workshop, inspection-room and production use respectively, delivering the repeatable precision required for machining and quality control.
1.05 mm Gauge Block, Hardened Special Steel, DIN EN ISO 3650 Grade 1 - Metav IndustryLine
Take advantage of the combination of DIN EN ISO 3650 Grade 1 accuracy, hardened special steel construction and compact cross‑section for dependable reference measurements in quality control; order the gauge via Metav Werkzeuge or contact our advisers for application support. End gauge 1.05 mm – DIN EN ISO 3650, Grade 1 by Metav IndustryLine A precision End gauge 1.05 mm intended as a calibrated reference for dimensional inspection and routine verification in inspection labs and production environments. DIN EN ISO 3650 Grade 1 accuracy Hardened special steel for longevity Compact cross-section 30×9 / 35×9 mm Reliable reference for dimensional control The DIN EN ISO 3650 specification and Grade 1 classification designate this gauge as a high‑accuracy reference suitable for validation of measuring instruments and short‑range inspection tasks. As a calibrated small‑sized end gauge, it provides a stable dimensional standard that supports traceable measurement chains and reduces uncertainty in pass/fail checks. The nominal size of 1.05 mm and the precise ground surfaces make this component practical for repeatable verification steps in workshop and laboratory routines. Durable build for repeated use and low wear Manufactured from hardened special steel, the piece resists deformation and preserves the measuring surfaces over extended use. The material selection emphasises wear resistance and dimensional stability, so routine contact with gauge blocks, comparator anvils or part seats does not quickly degrade the reference. With a mass of just 0.004 kg, handling is effortless while the hardness ensures the gauge remains a reliable benchmark for many inspection cycles. Compact geometry that enhances handling and stability The cross‑section follows practical dimensions: up to 10 mm nominal size the profile is 30×9 mm, and from 10.1 mm the profile is 35×9 mm. This geometry combines a low profile for insertion into fixtures with sufficient sectional stiffness to prevent twisting during measurement and comparison tasks. The compact format helps maintain alignment in gauge stands and reduces the risk of operator‑induced error, thereby supporting faster, more consistent checks on small parts and assemblies. Suited uses and contribution to quality workflows Designed for use in calibration benches, incoming inspection and periodic verification procedures, this item supports compliance activities and helps streamline quality assurance processes. Its adherence to recognised standards aids documentation and auditability; keeping reference artefacts like this to hand accelerates setup and minimises downtime during measurement tasks. Confidence in results increases when a traceable, grade‑specified gauge is used as the reference in routine checks. Contact Metav Werkzeuge for application advice or to obtain the Metav IndustryLine end gauge and integrate a Grade 1 reference into inspection workflows; Metav’s specialists in Emmerich can advise on traceability and storage options. Technical data Article number: M319.0105.1 GTIN: 4054469130255 Tariff number: 90173000 Nominal size: 1.05 mm Weight: 0.004 kg Standard: DIN EN ISO 3650 Grade: 1 Facts Nominal dimension: 1.05 mm Cross-section up to 10 mm: 30 × 9 mm Cross-section from 10.1 mm: 35 × 9 mm Special features Material: Special steel, hardened Category: End gauges Application: Reference measurement and inspection FAQ What tolerance class does this end gauge conform to? The end gauge conforms to DIN EN ISO 3650, Grade 1, offering the accuracy expected for grade‑specified reference standards. Which material is used for the gauge and what benefit does it provide? The gauge is made from hardened special steel, which provides long‑term wear resistance and dimensional stability for repeated comparative measurements. Is the 1.05 mm gauge suitable for calibration benches and incoming inspection? Yes, the End gauge 1.05 mm is designed for use in calibration benches, incoming inspection and routine verification workflows where a stable, traceable reference is required. How does the cross‑section affect handling and measurement stability? The defined cross‑sections (30×9 mm up to 10 mm and 35×9 mm from 10.1 mm) give a low profile for easy insertion while maintaining sufficient stiffness to reduce torsion and handling error. Can this gauge be used as a routine production check standard? As a DIN EN ISO 3650 Grade 1 reference, this item is suitable for routine production checks when a high‑accuracy short‑range standard is required Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.05mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of a Grade 1 reference length with the thermal stability of ceramic and a compact 1.05 mm nominal size to secure reproducible setups and quick checks on comparators and micrometres. Order the gauge block directly via Metav Werkzeuge or contact our consultants for advice on integration and delivery. Ceramic gauge block M324.001.05 — Grade 1, 1.05 mm (Metav IndustryLine) The Ceramic gauge block M324.001.05 is a compact precision reference length designed for calibration tasks and setting operations in workshop and laboratory metrology. Grade 1 accuracy (DIN 861/1) Stable, wear‑resistant ceramic material Nominal length 1.05 mm Precision reference for calibration Reliable reference length for calibration and setup The ceramic gauge block is specified as Grade 1 (DIN 861/1), which makes it suitable where consistent reference lengths are required for workshop‑level calibration and instrument setup. With a nominal length of 1.05 mm, the block serves as a compact standard for quick verification of micrometres, comparators and gauge stacks. The declared grade signals manufacturing and inspection tolerances in line with recognised metrology practice, supporting faster decision‑making during quality control and reducing rework by providing a dependable baseline measurement. Durable ceramic design that keeps calibration stable Manufactured from ceramic, the block offers wear‑resistant surfaces and low thermal expansion, so its length remains stable during routine handling and short temperature fluctuations common in production environments. Ceramic material also contributes to a non‑magnetic, corrosion‑resistant reference standard that requires minimal maintenance compared with metallic blocks. These properties translate into longer intervals between recalibrations and more reproducible readings when used as a reference in measurement chains or as part of a slip‑gauge set. Easy to integrate into quality processes and test benches As a compact reference standard, this block is suitable for integration into gauge stacks, comparator checks and verification procedures in both machine shops and inspection labs. The small footprint simplifies storage and handling while still providing the precision expected from a Grade 1 instrument. Supplied with clear identification (SKU M324.001.05) and traceable labelling, the block supports organised workflows and simplifies documentation for internal quality systems. For a reliable Grade 1 ceramic reference, contact Metav Werkzeuge for purchasing and tailored advice — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M324.001.05 GTIN: 4054469142425 Tariff number: 90173000 Material: Ceramic Nominal length: 1.05 mm Grade: 1 (DIN 861/1) Weight: 0.001 kg Facts Nominal length: 1.05 mm Weight: 0.001 kg GTIN: 4054469142425 Tariff number: 90173000 Special features Wear‑resistant ceramic Non‑magnetic and corrosion‑resistant Category: Gauge block EClass: 21170108 FAQ What accuracy class does this gauge block provide? The block is specified as Grade 1 according to DIN 861/1, offering the tolerances and manufacturing quality associated with that class for workshop and calibration use. Is the material suitable for repeated handling and stacking? Yes, the ceramic construction is wear‑resistant and exhibits low thermal expansion, making it well suited to repeated handling and use in gauge stacks and comparator checks. Can this block be used for micrometre and comparator verification? The product serves as a compact reference length for setting and checking micrometres, dial indicators and comparators in routine metrology tasks. How is the product identified for inventory and traceability? Identification is provided by the SKU M324.001.05 and GTIN 4054469142425, which simplify inventory control and documentation. Is this reference suitable for an inspection lab or a production workshop? The Grade 1 ceramic block is appropriate for both workshop and inspection‑lab applications where a stable, compact reference length is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.06 mm Gauge Block Single End Measurement Grade 0 DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
High-precision reference for calibration and inspection: DIN EN ISO 3650 grade 0 accuracy combined with a hardened special steel body ensures stable length and long service life. The compact form factor and traceable specification simplify routine checks and documentation. Order the single end gauge directly via Metav Werkzeuge or ask our consultants if needed. Single end gauge 1.06 mm — Metav IndustryLine end gauge with DIN EN ISO 3650 grade 0 accuracy Single end gauge 1.06 mm serves as a compact, high-accuracy reference standard for laboratory and workshop inspection tasks, designed for repeatable length verification and gauge block comparison. DIN EN ISO 3650 grade 0 tolerance Hardened special steel construction Reference size 1.06 mm for calibration tasks Compact cross-section for bench use Reliable reference for precision inspection A precision reference gauge with a nominal dimension of 1.06 mm offers a clear, verifiable basis for calibration and acceptance tests. Manufactured to DIN EN ISO 3650 and produced to grade 0, this gauge functions as a stable benchmark in quality control processes where tight dimensional conformity is required. The documented tolerance class reduces ambiguity during inspections and supports consistent pass/fail decisions on production lines and in metrology laboratories. Durable construction for long-term reproducibility Constructed from hardened special steel, the gauge resists wear and maintains dimensional stability under regular use. This material choice minimises surface deformation and abrasion, which translates into fewer replacement cycles and more consistent measurement results over time. The compact mass and rigid profile help to avoid bending during handling, ensuring that repeated comparisons remain within expected limits and that measurement uncertainty is kept low. Practical dimensions that support easy handling and integration The gauge’s cross-section is dimensioned for practical clamping and handling: 30 x 9 mm for sizes up to 10 mm, increasing to 35 x 9 mm for larger diameters. These profiles balance stiffness and gripability, making the part straightforward to seat in comparator fixtures or bench setups. The light weight and small footprint allow integration into existing gauge sets and inspection trays without significant changes to workflow or storage arrangements. Professional suitability and supply chain confidence Designed for professional workshops and inspection laboratories, this end gauge provides a traceable, industry-recognised reference for routine checks and comparative measurements. Supplied by Metav IndustryLine, it fits into a broader quality assurance strategy that values predictable results and dependable availability. The clear specification and robust material choice make it an efficient tool for maintaining inspection throughput while protecting measurement integrity. Contact Metav Werkzeuge for availability and expert advice on the Metav IndustryLine single end gauge 1.06 mm (SKU M319.0106.0) and to discuss calibration options Technical Data Article number: M319.0106.0 GTIN: 4054469130262 Label: Single end gauge 1.06 mm, DIN EN ISO 3650, grade 0 Facts Nominal dimension: 1.06 mm Grade: 0 Material: Special steel, hardened Weight: 0.004 kg Cross-section: up to 10 mm: 30 x 9 mm; from 10.1 mm: 35 x 9 mm TARIC/HS code: 90173000 Special features Standard: DIN EN ISO 3650 Category: End gauges Supplier series: Metav IndustryLine FAQ What tolerance class does this gauge meet? The single end gauge meets DIN EN ISO 3650 specifications at grade 0, making it suitable as a high-precision reference for comparative checks. Which material is used for the gauge? The gauge is manufactured from hardened special steel, chosen for wear resistance and dimensional stability under repeated use. Is the size documented for integration into gauge sets? Yes; the nominal size is 1.06 mm and the cross-section is specified as 30 x 9 mm (up to 10 mm) and 35 x 9 mm (from 10.1 mm), enabling straightforward fixture and tray integration. What is the article number if a replacement or matched set is required? The SKU for ordering and documentation is M319.0106.0 and the GTIN is 4054469130262. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.06 mm Go Gauge Pin, Hardened Special Steel, Grade 1, DIN EN ISO 3650 - Metav IndustryLine
Order a dependable reference standard that combines traceable conformity, Grade 1 accuracy and durable construction for repeatable workshop inspections; acquire directly via Metav Werkzeuge or consult our specialists for application advice. End gauge 1.06 mm (DIN EN ISO 3650) — Grade 1, hardened special steel — Metav IndustryLine An End gauge 1.06 mm designed as a compact, certified reference for dimensional checks and routine verification in production and inspection environments. DIN EN ISO 3650 compliant, Grade 1 accuracy Hardened special steel construction Compact cross-section 30 x 9 mm for stability Lightweight 4 g for easy handling Dependable accuracy that supports quality control The product is manufactured to DIN EN ISO 3650 and rated Grade 1, providing a clearly defined tolerance band for reference measurements. As a 1.06 mm nominal size standard, it serves as a precise benchmark for gauge checks and comparator setups, reducing measurement uncertainty in routine inspections. The normative conformity means laboratories and workshops can rely on a repeatable reference when documenting dimensional conformity against established standards. Robust material and form for long-term stability Crafted from hardened special steel, the reference maintains dimensional integrity under frequent use and resists rapid wear that would compromise repeatability. With a compact cross-section 30 x 9 mm, the gauge offers a favourable stiffness-to-size ratio, helping to avoid torsion during handling. The unit’s lightweight nature (approx. 4 g) aids fast placement in test fixtures and minimises operator fatigue during serial checks, while the hardened surface extends service life and keeps maintenance effort low. Practical role in calibration and inspection workflows This compact reference functions as a reliable end measure in inspection routines, alignment procedures and master comparisons. Integration into daily quality checks simplifies pass/fail assessments and supports traceable documentation across production batches. The End gauge 1.06 mm from Metav IndustryLine is suitable for workshop metrology where a small, authoritative standard is required to validate measuring instruments and to corroborate process control decisions. Contact Metav Werkzeuge for tailored advice on integrating Metav IndustryLine end gauges into inspection routines and to ensure the correct reference standards are selected for the measurement task at hand. Technical data Article number: M319.0106.1 GTIN: 4054469130279 Norm: DIN EN ISO 3650 Material: Spezialstahl, gehärtet Grade: 1 Facts Nominal size: 1.06 mm Weight: 0.004 kg (approx. 4 g) Cross-section: up to 10 mm: 30 x 9 mm; from 10.1 mm: 35 x 9 mm Tariff number: 90173000 Special features Category: End measures (end gauges) Compact dimensions for stiff, repeatable contact Suitable as a workshop and calibration reference Manufacturer brand: Metav IndustryLine FAQ What level of accuracy does this end gauge provide? The end gauge conforms to DIN EN ISO 3650 and is specified as Grade 1, giving a defined tolerance suitable for reliable workshop and inspection use with documented repeatability. Is the material suitable for regular use in production environments? Yes, the hardened special steel construction of the Metav IndustryLine end gauge ensures wear resistance and long-term dimensional stability under frequent handling. Which nominal size is this reference available in and what is its cross-section? This reference is the 1.06 mm nominal size; for nominal sizes up to 10 mm the cross-section is 30 x 9 mm, providing a stable form factor for contact measurement. Can this end gauge be used as a master for comparator setups? The End gauge 1.06 mm from Metav IndustryLine is designed for use as a compact master in comparator and verification tasks where a small, normative reference is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.06mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Compact, wear‑resistant ceramic reference with Grade 1 (DIN 861/1) accuracy and a nominal length of 1.06 mm, delivering a stable, space‑saving standard for fine length setting; order directly via Metav Werkzeuge or ask our consultants if needed Ceramic gauge block 1.06 mm — Grade 1 (DIN 861/1) by Metav IndustryLine The Ceramic gauge block 1.06 mm is a compact reference standard designed for precision length setting and fine calibration tasks in metrology and quality inspection Grade 1 accuracy per DIN 861/1 Ceramic material for corrosion and wear resistance Compact 1.06 mm reference gauge block Mass 0.001 kg for precise handling Consistent, measurable accuracy for tight tolerances As a Grade 1 reference produced to DIN 861/1, this ceramic gauge block offers dependable dimensional performance for routine verification and setup tasks. The small nominal length of 1.06 mm provides a precise building block for gage stacks and comparator references, reducing the time spent on iterative adjustments and improving process throughput. The clearly defined specification reduces interpretation effort during inspection planning and supports repeatable results in workshop and laboratory environments. Material benefits that support repeatable measurements Manufactured from ceramic, the block delivers wear resistance and dimensional stability under normal handling, which together extend service life and lower lifetime replacement costs. The very low mass (0.001 kg) makes the component easy to manoeuvre during stacking and inspection, while the non‑metallic composition minimises corrosion risk in standard ambient conditions. These material characteristics contribute to reduced measurement drift and a lower rate of corrective recalibrations, which is particularly valuable for frequent short‑cycle checks. Practical fit for inspection workflows and reference stacks This compact reference is intended for integration into established calibration routines: it complements sets for micro‑measurements, serves as a spacer in gauge stacks and functions as a quick verification artefact at the inspection bench. Its small footprint saves tray space and simplifies handling during fast throughput checks. The clear technical identity of the item streamlines inventory control and traceability when used alongside larger standards and locking fixtures, helping to maintain a robust quality regime with minimal operational friction. Trusted supply and sector relevance Provided under the Metav IndustryLine umbrella, the item benefits from a supplier that focuses on making precision accessible across workshops and industry. Metav’s distribution and inventory approach supports reliable replenishment and consistent product quality for companies seeking to reduce supplier complexity. The combination of compact form, ceramic durability and Grade 1 specification makes this block particularly suitable for laboratories, fine mechanical workshops and quality departments that require small, stable references for everyday use. For enquiries about matching gauge block sets, traceability options or application advice for Metav IndustryLine ceramic gauge blocks (SKU M324.001.06), contact Metav Werkzeuge for tailored guidance and supply solutions Technical data Article number: M324.001.06 GTIN: 4054469142432 Tariff code: 90173000 Manufacturer: Metav IndustryLine Numbers / Core technical data Nominal length: 1.06 mm Mass: 0.001 kg Grade: 1 eClass: 21170108 Special features / Materials Material: Ceramic Category: Gauge block (Endmasse) Intended use: Reference standard for precision length setting Story trigger: endmasse FAQ What accuracy level does this gauge block provide? The ceramic gauge block is specified as Grade 1 according to DIN 861/1, offering a standard industrial accuracy suitable for reference stacking and routine verification. Is the ceramic material suitable for regular shop use? Yes. The ceramic composition provides good wear resistance and reduced corrosion risk in normal ambient conditions, making the block suitable for frequent handling and everyday inspection tasks. How should this gauge block be handled and stored to preserve accuracy? Handle the block with clean, dry hands or gloves, avoid hard impacts and store it in a dry, dust‑free environment. Regular cleaning with a soft, lint‑free cloth and controlled storage reduces surface contamination and preserves dimensional stability. Can this item be used in a gage block set or combined with other standards? This Ceramic gauge block 1.06 mm (Metav IndustryLine, SKU M324.001.06) is designed for stacking with other gauge blocks and reference standards to build specific nominal lengths for calibration and inspection. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.07 mm Gauge Block DIN EN ISO 3650 Grade 1, Hardened Special Steel - Metav IndustryLine
Take advantage of DIN EN ISO 3650 Grade 1 accuracy combined with a hardened special steel body and a compact 1.07 mm nominal size to secure a reliable dimensional reference in the workshop or calibration bench. Order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. End gauge 1.07 mm — Precision gauge block, DIN EN ISO 3650, Grade 1 (Metav IndustryLine) The End gauge 1.07 mm is a precision gauge block designed as a dimensional reference and setting standard for metrology, measurement benches and workshop calibration tasks. DIN EN ISO 3650 Grade 1 accuracy Hardened special steel construction Compact 1.07 mm nominal size Dependable reference for measurement and setup As a compact precision reference, this gauge block meets DIN EN ISO 3650 and is classified Grade 1, offering a stable baseline for setting instruments and verifying small dimensions. The nominal size of 1.07 mm provides a clearly defined reference step that simplifies the calibration of micrometers, comparators and small gauges. Because the geometry adheres to recognised standards, traceability within measurement chains is supported and results remain comparable across shifts and locations. Robust construction for repeatable readings Manufactured from hardened special steel, the block resists wear in regular use and retains its dimensional integrity over time. The specified cross-section (up to 10 mm: 30 x 9 mm; above 10.1 mm: 35 x 9 mm) balances handling and stiffness, reducing the risk of twist or deformation during placement. The light mass aids safe manipulation while the hardened finish minimises surface degradation, so the reference remains consistent for routine checks and repeated seating in gauge stacks. Integrates smoothly into quality processes The compact form factor and standard conformity make this block suitable for both workshop verification and laboratory routines where small-step references are required. Identified by SKU M319.0107.1 and GTIN 4054469130293, the component is straightforward to log into inventory and trace within quality documentation. For process planners, the block serves as a pragmatic element of a modular set of references, enabling quick comparative checks and ensuring measurement chains remain aligned with inspection requirements. Engage Metav Werkzeuge for supply of this Metav IndustryLine gauge block and benefit from direct access to European stock and measurement expertise in Emmerich; contact our team for application support or to request a quotation at info@metav-werkzeuge.com Technical data Article number: M319.0107.1 GTIN: 4054469130293 Tariff number: 90173000 Facts Nominal size: 1.07 mm Weight: 0.004 kg Cross-section: up to 10 mm — 30 x 9 mm; from 10.1 mm — 35 x 9 mm Special features Material: hardened special steel Standard: DIN EN ISO 3650 Grade: 1 Category: End gauges (gauge blocks) FAQ What level of accuracy does this gauge provide? The End gauge 1.07 mm is manufactured to DIN EN ISO 3650 Grade 1, offering the precision expected from Grade 1 gauge blocks for reliable workshop and metrological use. Is the gauge block suitable for routine calibration tasks? Yes; the block's conformity to DIN EN ISO 3650 and its hardened special steel construction make the End gauge 1.07 mm appropriate as a setting and comparative reference in routine calibration and verification procedures. How is the item identified for inventory and traceability? This Metav IndustryLine gauge block is listed under SKU M319.0107.1 with GTIN 4054469130293, facilitating straightforward recording in quality and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.07 mm Gauge Block Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of a grade 0 reference standard that combines DIN EN ISO 3650 conformity, hardened special steel construction and a compact cross‑section for reliable workshop checks; order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Single end gauge 1.07 mm — DIN EN ISO 3650, Grade 0, hardened special steel (Metav IndustryLine) A single end gauge in hardened special steel designed as a precise reference for inspection and dimensional verification in industrial metrology and workshop calibration. DIN EN ISO 3650 compliant, grade 0 Hardened special steel construction Nominal size 1.07 mm reference standard Compact cross-section for stable handling Consistent reference quality for routine inspection The 1.07 mm single end gauge is manufactured to DIN EN ISO 3650 with grade 0 tolerance, delivering a reproducible reference that supports repeatable pass/fail checks and simple verification tasks. As a hard gauge in hardened special steel, it provides dimensional stability under normal workshop conditions and resists wear during contact inspection. The calibrated nominal size serves as a reliable standard for setting comparators, verifying micrometres or checking small measuring fixtures, reducing uncertainty in routine quality control. Robust design and handling benefits for everyday use A compact cross‑section—specified as 30×9 mm for sizes up to 10 mm and 35×9 mm from 10.1 mm—ensures a stiff, easy‑to‑grip profile that minimises bending and improves tactile feedback when seating the gauge. The modest mass (approx. 0.004 kg) and hardened construction enable frequent use without rapid degradation, making the block well suited for inspection benches and gauge sets where durability and consistent contact surfaces matter. The simple geometry also eases storage and integration into existing gauge trays or sets. Practical applications and trust in supply This single end gauge is intended for industrial metrology tasks where a small but accurate reference standard is required: presetting small measurement tools, comparator checks and spot verification in assembly lines. Being part of the Metav IndustryLine, the article suits workshops and quality departments that value a transparent supply chain and consistent technical standards. The robust norm compliance and material choice provide a rational basis for choosing this gauge as a baseline reference in serial inspection workflows. Contact Metav Werkzeuge for specification advice and to order the Metav IndustryLine single end gauge 1.07 mm; our Emmerich team will advise on delivery, traceability and suitability for your inspection process. Technical Data Article number: M319.0107.0 GTIN: 4054469130286 Norm: DIN EN ISO 3650 Grade: 0 Nominal size: 1.07 mm Facts Weight: 0.004 kg Cross-section: 30×9 mm (≤10 mm) / 35×9 mm (≥10.1 mm) Tariff number: 90173000 Special features Material: hardened special steel Category: end gauge Manufacturer series: Metav IndustryLine FAQ What tolerance class does this gauge follow? The single end gauge is supplied to grade 0 tolerance in accordance with DIN EN ISO 3650, offering a reliable reference for workshop inspection. Which material is used for the gauge and what is the benefit? The gauge is produced from hardened special steel, which improves wear resistance and dimensional stability during repeated contact measurements. Can this gauge be used to set micrometres and comparators? Yes, the 1.07 mm nominal size is suitable as a reference for setting and checking micrometres, comparators and small measuring fixtures in inspection routines. Is the cross-section the same for all sizes? The cross-section follows the specification: 30×9 mm for sizes up to 10 mm and 35×9 mm for sizes from 10.1 mm, providing appropriate stiffness for the respective nominal ranges. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.07mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the combination of Grade 1 accuracy, ceramic thermal stability and a precisely defined 1.07 mm nominal size for consistent reference measurements; order directly via Metav Werkzeuge or consult our specialists for integration into calibration routines. Ceramic gauge block 1.07 mm – Grade 1 precision (Metav IndustryLine) A Ceramic gauge block 1.07 mm, Grade 1 DIN 861/1 engineered as a compact reference standard for laboratory checks and workshop inspection tasks. Grade 1 accuracy per DIN 861/1 Stable, non-corroding ceramic material Nominal size 1.07 mm for fine references Consistent precision for everyday calibration needs The block delivers Grade 1 conformity according to DIN 861/1, making it suitable where repeatable length standards are required. As a compact reference element, the component reduces uncertainty in comparator checks and routine calibration sequences. The combination of a defined 1.07 mm nominal size and the inherent dimensional stability of the ceramic body supports reproducible results across repeated measurements, which aids throughput in quality assurance workflows. Material benefits that reduce handling effects Made from high-density ceramic, this gauge block offers low thermal expansion compared with many metals, improving short-term dimensional stability during measurement exchanges. The material is also inherently non-corroding, which reduces maintenance effort and preserves the reference surface over long inspection intervals. These properties translate into fewer re-measurements and more reliable baselines for internal quality control. Compact format for precision sub-millimetre references The small nominal dimension provides a stable reference for fine calibration tasks and microfabrication checks. Its compact geometry minimises bending or handling errors when compared with longer standards, which is advantageous in bench-top metrology environments. The compact block is therefore well suited for laboratory fixtures and small-part inspection where space and rigidity are decisive factors. Integration into test benches and comparators The geometry and grade specification make the component compatible with comparator stands and optical measuring instruments commonly used in calibration labs. Where traceable references are required for instrument verification, the piece acts as a convenient short-length standard for transfer measurements or as a calibration artefact in periodic verification plans. Durability and lifecycle considerations The ceramic construction combines wear resistance with surface stability, offering a long service life under normal handling. For organisations aiming to reduce the frequency of replacement standards, the material choice supports extended intervals between surface reconditioning. The element’s robustness under routine use makes it a practical investment for busy metrology departments. Identification and practical handling Compact and lightweight, the element is easy to store and reference within a calibrated set. The product is identified as part of the Metav IndustryLine range and supplied with a clear article designation for inventory control. Its small mass reduces the need for elaborate handling aids, while the precise nominal size ensures it functions reliably as a short reference in multi-step calibration procedures. Prefer Metav IndustryLine when specifying compact length standards—contact Metav Werkzeuge for precise ordering guidance and assistance integrating this ceramic reference into existing calibration plans Technical data Article number: M324.001.07 GTIN: 4054469142449 Category: Endmasse (gauge blocks) Material: Ceramic Nominal size: 1.07 mm Grade: 1 (DIN 861/1) Weight: 0.001 kg Tariff number: 90173000 Facts Nominal size: 1.07 mm Weight: 0.001 kg Grade: 1 GTIN: 4054469142449 Special features Ceramic material for thermal stability Suitable as precision length standard Manufactured for Metav IndustryLine Product image available FAQ What tolerance class does this gauge block meet? The Ceramic gauge block 1.07 mm, Grade 1 DIN 861/1 conforms to Grade 1 tolerances as specified by DIN 861/1 and is suitable for routine laboratory reference tasks. Is the material suitable for long-term reference use? Yes. The ceramic composition of the Metav IndustryLine gauge block provides low thermal expansion and good wear resistance, making it suitable for repeated use as a short-length standard. How should this reference be handled and stored? Handle the block with clean, dry gloves and store it in a dust-free environment. The compact size reduces handling-induced bending, but careful storage in a protective case is recommended to preserve surface quality. Can this block be used with optical comparators and microscope stages? The nominal size and Grade 1 accuracy make it compatible with comparator stands and optical measurement setups where short, stable references are required. What is the product identification for ordering and inventory? Order and stock under SKU M324.001.07 (GTIN 4054469142449) in the Metav IndustryLine range for consistent identification in procurement and calibration records. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.08 mm Gauge Block Single End, Hardened Special Steel, DIN EN ISO 3650 Grade 0 - Metav IndustryLine
Benefit from Grade 0 conformity to DIN EN ISO 3650 and a hardened special steel construction that delivers stable, repeatable reference measurements; combine high‑precision performance with robust handling for everyday calibration tasks. Order this single gauge block directly via Metav Werkzeuge or consult our specialists for further technical advice. Single gauge block 1.08 mm — Grade 0 reference piece, DIN EN ISO 3650 (Metav IndustryLine) Single gauge block 1.08 mm is a compact, high‑precision reference for calibration and dimensional verification in metrology laboratories and workshop environments Grade 0 accuracy (DIN EN ISO 3650) Hardened special steel construction Compact nominal size 1.08 mm Reliable reference accuracy for traceable measurements This grade‑0 gauge block is manufactured to DIN EN ISO 3650, providing a well‑defined tolerance class suitable for calibration masters and comparison standards. The product’s nominal size of 1.08 mm is held to tight limits, enabling repeatable and traceable checks of micrometrology instruments. As a result, inspection routines and setting procedures benefit from reduced uncertainty and clearer pass/fail criteria, which supports consistent production quality and helps maintain documented measurement procedures. Durable construction that keeps calibration intervals long Made from hardened special steel, the block combines surface wear resistance with thermal stability for everyday workshop use. The specified cross‑section dimensions (up to 10 mm → 30 x 9 mm; from 10.1 mm → 35 x 9 mm) give the piece a practical contact face and handling geometry, reducing the risk of edge damage during assembly or stacking. Low mass (approx. 0.004 kg) aids delicate positioning without inducing excessive handling force, and the material choice helps ensure long‑term stability between recalibrations. Practical use in calibration benches and verification procedures As a single reference element the block functions as a setting standard for gauge blocks sets, comparators and high‑precision calipers. Its Grade 0 rating makes it suitable for high‑accuracy reference tasks where nominal dimensions must be reproduced reliably. The combination of the DIN normative backing and robust material means the block is equally at home in a laboratory environment or a production quality area, providing a compact solution for routine verification and assembly inspection. For supply or application advice on this Metav IndustryLine reference standard, contact Metav Werkzeuge in Emmerich for delivery options and technical consultation at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M319.0108.0 GTIN: 4054469130309 Standard: DIN EN ISO 3650 Facts Nominal size: 1.08 mm Grade: 0 Weight: 0.004 kg Special features Material: hardened special steel Cross-section: up to 10 mm → 30 x 9 mm; from 10.1 mm → 35 x 9 mm Category: gauge block (single) FAQ What tolerance class does this reference comply with? The single gauge block 1.08 mm is manufactured to Grade 0 in accordance with DIN EN ISO 3650, providing the tolerance class specified for high‑precision reference usage. Which material is used and how does it affect handling? This reference is made from hardened special steel, chosen for wear resistance and dimensional stability; the material supports repeated use and reduces frequency of reconditioning. Can the block be used as a master for caliper verification? Yes, the single gauge block 1.08 mm serves as a compact master for setting and checking calipers, comparators and small gauge block stacks in workshop and laboratory contexts. What are the cross‑section dimensions and why do they matter? Cross‑section is 30 x 9 mm for blocks up to 10 mm and 35 x 9 mm from 10.1 mm; these profiles provide robust bearing faces that ease handling and stacking while protecting edges during routine use. Is the nominal size traceable to a standard? The nominal dimension of 1.08 mm is produced under the traceability framework implied by conformity to DIN EN ISO 3650, supporting documented calibration chains where required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.08mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
The combination of ceramic construction, Grade 1 conformity to DIN 861/1 and a compact 1.08 mm nominal length provides a stable and wear‑resistant reference for fine calibration tasks; order directly via Metav Werkzeuge or contact our consultants for application advice. Ceramic gauge block 1.08 mm, Grade 1 (DIN 861/1) — Metav IndustryLine precision reference The Ceramic gauge block 1.08 mm, Grade 1 (DIN 861/1) is a compact reference standard designed for high‑precision length measurement and routine calibration in metrology laboratories and workshop quality control. High thermal stability ceramic Grade 1 tolerance (DIN 861/1) Nominal size 1.08 mm for fine calibration Compact, lightweight reference standard Stable material for reproducible references Made from ceramic, this gauge block combines low thermal expansion with high surface hardness to deliver consistent dimensional behaviour in typical workshop and laboratory environments. The result is a reference standard that resists wear and maintains its nominal length over repeated use, reducing the need for frequent replacement and helping to sustain measurement quality across production batches. Accuracy suitable for precision calibration and inspection Manufactured to Grade 1 in accordance with DIN 861/1, the block serves as a reliable datum for calibration benches and comparator setups. Its specification supports traceable checks of micrometrology instruments and small‑part inspection routines, contributing directly to process stability and fewer non‑conforming parts. The compact nature of the item allows simple integration into existing reference sets or use as a standalone calibration artefact. Practical handling and identification for everyday use With a nominal length of 1.08 mm and a mass of 0.001 kg, the block is exceptionally compact and easy to handle during tight‑tolerance checks. The small form factor minimises thermal lag during short tasks and is convenient for assembly‑level inspections where space is limited. Clear product identification (SKU and GTIN) supports inventory control and documentation of calibration assets within maintenance or quality systems. For certified reference standards from Metav IndustryLine, contact Metav Werkzeuge in Emmerich for procurement and technical advice — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: M324.001.08 GTIN: 4054469142456 Material: Ceramic Nominal size: 1.08 mm Weight: 0.001 kg Grade: 1 (DIN 861/1) Tariff number: 90173000 Facts Nominal size: 1.08 mm Weight: 0.001 kg GTIN: 4054469142456 Tariff number: 90173000 Special features Compact ceramic gauge block Conforms to DIN 861/1, Grade 1 Category: Gauge blocks / End measures SKU: M324.001.08 FAQ What is the primary application for this ceramic gauge block? The ceramic gauge block 1.08 mm, Grade 1 (DIN 861/1) is intended as a reference standard for precision length measurement, calibration of small instruments and verification tasks in metrology and workshop quality control. What does Grade 1 (DIN 861/1) signify for measurements? Grade 1 according to DIN 861/1 denotes a high manufacturing class that ensures the block is suitable as a fine calibration reference; it indicates tight manufacturing control and suitability for routine precision checks. How does the ceramic material affect performance? Ceramic provides thermal stability and superior surface hardness compared with many metals, which helps the gauge block maintain its nominal dimension and resist wear during repeated use. Are there special handling recommendations for this reference standard? Handle the block with clean, lint‑free gloves or tweezers, avoid impacts and store in a dry, clean environment to preserve the measuring faces. The compact mass (0.001 kg) reduces thermal transients during short measurements. Which identification details help with asset management? The product is listed under SKU M324.001.08 and GTIN 4054469142456, which supports tracking, documentation and cataloguing in quality and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.08mm End Gauge DIN EN ISO 3650 Grade 1, Hardened Special Steel - Metav IndustryLine
Take advantage of DIN EN ISO 3650 conformity, Grade 1 accuracy and a hardened special steel construction for reproducible gauge stacks; Order the gauge block directly via Metav Werkzeuge or ask our consultants if needed. Gauge Block 1.08 mm – DIN EN ISO 3650, Grade 1 (Metav IndustryLine) A gauge block 1.08 mm designed as a precise length standard for calibration, inspection and high-precision stacking in metrology laboratories and workshop environments DIN EN ISO 3650 Grade 1 accuracy Hardened special steel construction Nominal length 1.08 mm for precision stacks Low mass 4 g for easy handling Consistent, certified accuracy for calibration tasks The block is manufactured to DIN EN ISO 3650 and delivered as a Grade 1 length standard, providing a dependable reference for length comparisons and stack assemblies. Certified conformity supports consistent results across repeated measurements, which reduces uncertainty in inspection routines and minimises rework. The nominal size of 1.08 mm makes this block suitable as a fine increment in precision gauge stacks, allowing incremental step‑ups when determining calibrated lengths or when setting up comparative checks on micrometers and calipers. This focus on reproducibility is a rational advantage for quality-controlled production and laboratory workflows. Practical design that supports efficient handling and longevity Constructed from hardened special steel, the block combines surface stability with resistance to wear, ensuring long service life even under frequent handling. The compact cross‑section (30 x 9 mm for nominal lengths up to 10 mm) and low mass (4 g) allow straightforward placement and removal during stacking, improving throughput in routine calibration sequences. The geometry aids thermal equalisation between blocks when building stacks, which helps maintain dimensional integrity during short measurement cycles. The robust finish also simplifies surface care and inspection, contributing to predictable performance with minimal maintenance. Applications where the block adds measurable value This gauge block serves as a high-resolution element for calibration benches, workshop quality control and laboratory standards where fine increments are required. Typical uses include forming reference stacks for comparative measurement, verifying the accuracy of dial indicators and setting precise gauge lengths for fixture inspection. The compact nominal size and Grade 1 tolerance make it particularly useful in metrology tasks that demand fine-step adjustments rather than bulk length coverage. For facilities seeking traceable components, the product's identification enables straightforward inventorying and process documentation. For traceable calibration and Grade 1 accuracy order the Metav IndustryLine gauge block (1.08 mm) from Metav Werkzeuge in Emmerich or request technical advice by email at info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data Article number: M319.0108.1 GTIN: 4054469130316 Norm: DIN EN ISO 3650 Grade: 1 Facts Nominal length: 1.08 mm Weight: 0.004 kg Cross-section: 30 x 9 mm (nominal length ≤ 10 mm) Tariff number: 90173000 Special features Material: hardened special steel Category: gauge block / end measure Compact geometry for precision stacks Suitable for laboratory and workshop calibration FAQ What tolerance class does this block meet? The block meets Grade 1 tolerance according to DIN EN ISO 3650, providing a reliable reference for calibration and inspection tasks. Is the material suitable for regular workshop use? Yes, the hardened special steel construction is designed for regular handling and retains dimensional stability under typical workshop conditions. How is this block best used within a gauge stack? The 1.08 mm nominal length is intended as a fine increment within precision gauge stacks, allowing accurate stepwise extension of reference lengths for measurement setups. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.09 mm Gauge Block Single End Measure DIN EN ISO 3650 Grade 0, Hardened Special Steel - Metav IndustryLine
Precision and DIN EN ISO 3650 Grade 0 accuracy, combined with a hardened special steel construction and compact dimensions, deliver a stable, repeatable reference for workshop and inspection tasks; order the single end gauge directly via Metav Werkzeuge or consult our advisors for application support. Single end gauge 1.09 mm — gauge block, DIN EN ISO 3650, Grade 0 — Metav IndustryLine The single end gauge 1.09 mm serves as a traceable, handheld reference for setting and checking measuring instruments in inspection, toolmaking and production metrology. DIN EN ISO 3650 Grade 0 accuracy Hardened special steel construction Nominal size 1.09 mm Reliable reference that reduces setup time The compact reference element offers a nominal size of 1.09 mm and conforms to DIN EN ISO 3650 at Grade 0, providing a defined tolerance band that simplifies go/no‑go checks and gauge comparisons. As a calibrated physical standard it shortens instrument setup and minimises adjustment cycles, which translates into measurable time savings on repetitive tasks. The standardised tolerance class supports consistent quality checks across shifts and machines, improving throughput without sacrificing measurement confidence. Robust, easy‑to‑handle design for frequent use Manufactured from hardened special steel, the block is machined to tight form specifications and finished for corrosion resistance and long service life. The cross‑section for sizes up to 10 mm is 30 x 9 mm, giving a stable contact face while keeping the element light at around 0.004 kg, so handling is intuitive and fatigue is reduced during repetitive inspections. This construction ensures a durable reference that resists deformation from normal handling, preserving the dimensional integrity required for precise setting of micrometres, callipers and comparator fixtures. Proven quality and practical logistics for the workshop Supplied under the Metav IndustryLine label and traceable via SKU M319.0109.0, the compact gauge block fits into standard inspection kits and is suitable for production floors and calibration benches alike. The combination of standard conformity, resilient material and compact footprint makes it a pragmatic choice where space is limited but measurement certainty remains critical. For procurement and application advice, Metav’s European distribution and quality‑filter approach ensure reliable delivery and practical support for industrial customers. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine single end gauge 1.09 mm can be integrated into existing inspection routines or to request further technical details via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M319.0109.0 GTIN: 4054469130323 Norm: DIN EN ISO 3650 Grade: 0 Material: Spezialstahl, gehärtet Nominal size: 1.09 mm Weight: 0.004 kg Customs tariff number: 90173000 Numbers / Core technical data Nominal size: 1.09 mm Weight: 0.004 kg Cross-section: bis 10mm 30 x 9 mm, ab 10,1mm 35 x 9 mm GTIN: 4054469130323 Customs tariff number: 90173000 Special features / Versions Conformity: DIN EN ISO 3650 Grade 0 Construction: hardened special steel Category: End gauges (gauge blocks) Label: Einzel-Endmaß 1,09 mm FAQ What level of accuracy does this gauge provide? The single end gauge 1.09 mm is manufactured to DIN EN ISO 3650 Grade 0, offering the tight tolerances associated with that grade and a reliable reference for workshop verification and instrument setting. Which materials is the gauge suitable for when checking instruments? As a reference artefact, the gauge block is made of hardened special steel and is intended to set or check measuring devices rather than to interact directly with workpiece materials. How should the gauge be cared for to preserve accuracy? Handle the Metav IndustryLine gauge with clean hands or gloves, store it dry and free from abrasive contact, and avoid shocks; periodic inspection against higher standards is recommended to confirm ongoing conformity. How can the gauge be ordered or referenced for procurement? Order using SKU M319.0109.0; the GTIN 4054469130323 and the DIN EN ISO 3650 Grade 0 designation aid procurement and inventory tracking. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.09 mm Gauge Block, DIN EN ISO 3650, Grade 1, Hardened Special Steel - Metav IndustryLine
A compact, high‑accuracy inspection tool: the plain plug gauge offers DIN EN ISO 3650 conformity and Grade 1 tolerance, delivering reliable dimensional checks for small bores. Made from hardened special steel, it combines long service life with consistently repeatable results — order via Metav Werkzeuge or consult the specialists for application advice. Metav IndustryLine plain plug gauge 1.09 mm (DIN EN ISO 3650, Grade 1) A plain plug gauge 1.09 mm for precise verification of bore diameters in precision engineering and small‑part quality control DIN EN ISO 3650 compliance Grade 1 tolerance class Hardened special steel construction Compact plug for precise bore checks Consistent accuracy that supports faster inspection The gauge is manufactured to DIN EN ISO 3650, Grade 1, and a nominal size of 1.09 mm, ensuring conformity with recognised metrology standards. This certification focus delivers a stable reference for comparative measurements and pass/fail checks, reducing variability in routine inspection. As a compact inspection implement, the plug performs rapid dimensional verification, supporting efficient process control and fewer downstream rejects through repeatable measurement behaviour. Robust materials for long service life and low maintenance Constructed from hardened special steel, the plug gauge resists normal workshop wear and maintains dimensional integrity across repeated use. The material choice offers favourable wear resistance and stability under handling, so calibration intervals remain practical for production environments. The modest mass and compact geometry also ease handling in tight assemblies while preserving the contact quality required for small‑bore evaluation. Practical role in documentable quality workflows As a purpose‑built gauge for bore assessment, this plug is suited to use in inspection stations, fixture checks and routine acceptance testing where precise nominal diameters must be confirmed. The tool’s conformity to a formal standard supports traceable quality documentation and aligns with typical shop‑floor inspection plans, making it a reliable artefact for control plans and routine dimensional audits. A dependable metrology choice from a dedicated supplier Supplied under the Metav IndustryLine label, the gauge benefits from a European distribution and quality‑control approach that emphasises accessible precision for workshops and industrial users. The compact design and standard conformity make it a practical addition to inspection kits where small, repeatable measurements are essential and where tool longevity reduces replacement frequency. Secure precise bore verification with the Metav IndustryLine plug gauge — contact Metav Werkzeuge for specification matching and local supply from Emmerich: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M319.0109.1 GTIN: 4054469130330 Nominal size: 1.09 mm Material: Spezialstahl, gehärtet Standard: DIN EN ISO 3650 Grade: 1 Weight: 0.004 kg Tariff number: 90173000 Facts Cross‑section small sizes: up to 10 mm → 30 x 9 mm Cross‑section larger sizes: from 10.1 mm → 35 x 9 mm Special features Plain plug gauge design Compact geometry for small bores Suitability: precision inspection and quality control FAQ What standard and tolerance class does this plug gauge follow? The plain plug gauge is specified to DIN EN ISO 3650 and produced to Grade 1 tolerance class, providing a standardised reference for small‑bore inspection. What is the gauge made from and how durable is it? The Metav IndustryLine plain plug gauge is manufactured from hardened special steel, offering good wear resistance and stable contact characteristics for repeated checks. For which inspection tasks is a 1.09 mm plug best suited? A 1.09 mm plug gauge is intended for verification of small bore diameters in precision engineering, fixture checks and routine dimensional control where a compact reference is required. Does the product support traceable quality documentation? The plug gauge’s conformity to DIN EN ISO 3650 facilitates its use within traceable inspection routines and quality documentation as a standardised measurement artefact. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.09mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Achieve repeatable micro‑measurements with a combination of ceramic construction, Grade 1 accuracy (DIN 861/1) and the compact 1.09 mm nominal size; ideal as a stable reference in precision workshops and calibration labs. Order the ceramic gauge block directly via Metav Werkzeuge or ask our consultants if needed. Ceramic gauge block 1.09 mm, Grade 1 (DIN 861/1) — Metav IndustryLine precision end gauge The ceramic gauge block 1.09 mm, Grade 1 is a thermally stable reference standard for lab calibration and fine‑mechanical verification, designed for incorporation into precision stacks and quality‑control routines. Ceramic material for thermal stability Grade 1 tolerance to DIN 861/1 Nominal size 1.09 mm for precision reference Reliable accuracy for reference and calibration The block serves as a compact reference standard, offering the repeatability required in calibration environments. Manufactured from ceramic, it presents low thermal expansion compared with many metals, which reduces size drift during temperature fluctuations and short handling times. The Grade 1 specification under DIN 861/1 signals a narrow tolerance band suitable for laboratory checks and reference stacks. Engineers and technicians benefit from a stable artefact for verifying micrometre and caliper performance, where dimensional certainty is the primary requirement. Practical role in measurement workflows As a small‑format end gauge, this item integrates easily into standard stacks or can be used singularly for spot checks on production machines. The 1.09 mm nominal size fills a fine increment in gauge sets, enabling closer step sizes between reference values. Its low mass and compact footprint simplify handling and storage while still delivering trustworthy contact surfaces for slip gauges and comparator use. The physical robustness of ceramic also minimises wear on faces that see repeated touching during routine verification, supporting consistent measurement outcomes. Handling, maintenance and compatibility Routine care extends the service life of ceramic reference standards: gentle cleaning, soft‑lined storage and avoidance of sharp impacts preserve flatness and surface integrity. The block’s material resists many common shop contaminants and will not corrode, which reduces maintenance effort compared with some metallic gauges. For compatibility, this reference element complements existing flat reference sets and can be combined into calibrated stacks for traceable master values. The combination of thermal stability and durable faces translates into lower drift and fewer recalibrations over time. Evidence and application scenarios Used in calibration labs, toolrooms and inspection benches, the block provides a measurable improvement in traceability when inserted into verification sequences. Its adherence to DIN 861/1 ensures acceptance in standards‑driven quality systems, while the ceramic body supports measurements where minimal thermal influence is critical. For applications requiring a compact but precise reference — such as micromechanical checks or fine production tolerancing — the block offers a reliable building block for measurement certainty. For traceable reference standards and tailored advice on integrating the Metav IndustryLine ceramic gauge block into existing calibration routines, contact Metav Werkzeuge for personalised consultation and ordering guidance Technical Data SKU: M324.001.09 GTIN: 4054469142463 Brand: Metav IndustryLine Material: Ceramic Nominal size: 1.09 mm Grade: 1 (DIN 861/1) Tariff number: 90173000 Weight: 0.001 kg Facts Nominal size: 1.09 mm Weight: 0.001 kg GTIN: 4054469142463 Tariff number: 90173000 Special features Ceramic material for low thermal expansion Grade 1 tolerance to DIN 861/1 Compact end gauge for reference stacks Category: Gauge block / end measure FAQ What level of accuracy does this gauge block provide? The ceramic gauge block is manufactured to Grade 1 in accordance with DIN 861/1, providing a narrow tolerance band suitable for laboratory and workshop reference use. Can this reference be combined into a calibrated stack? Yes, the ceramic gauge block 1.09 mm is intended for inclusion in gauge stacks and complements other end measures for creating traceable master sizes. Is the material suitable for routine shop use? The ceramic construction offers good resistance to corrosion and reduced thermal expansion, making it appropriate for regular verification tasks when handled and stored correctly. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.0mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Combining ceramic thermal stability, Grade 1 conformity and compact nominal size delivers a reliable reference standard for repeatable inspections; Order the ceramic end gauge M324.001 directly via Metav Werkzeuge or ask our consultants if needed. Ceramic End Gauge M324.001 — Grade 1, 1.0 mm (Metav IndustryLine) Ceramic end gauge M324.001 designed as a 1.0 mm Grade 1 reference for precision metrology and workshop calibration tasks. Ceramic for excellent thermal stability Grade 1 per DIN 861/1 accuracy Nominal size 1.0 mm for reference use Lightweight for safe handling Reference accuracy for repeatable measurements As a compact reference standard, this end gauge is manufactured to Grade 1 in accordance with DIN 861/1, which positions it for demanding inspection work and comparator use. The combination of minimal mass and the inherent dimensional stability of ceramic supports reproducible results when used as a gauge block or reference element. In routine quality-control cycles, such a reference reduces uncertainty caused by material expansion and wear, making it suitable for bench comparators and verification of micrometers or small measuring instruments. Stable material and workshop advantages The choice of ceramic as the construction material provides clear practical benefits: low thermal expansion, high hardness and strong wear resistance. These attributes translate into lower drift during temperature changes and extended service life compared with softer reference materials. The light mass also reduces the risk of damage when handling small gauges, while the non‑corroding surface minimises the need for frequent maintenance. For workshops that run repeated checks, this means fewer adjustments to the measuring chain and more consistent inspection throughput. Practical use and handling in inspection routines In inspection processes the gauge functions as a fixed standard for short-range comparisons and calibration checks. Proper storage on a dedicated reference surface and gentle handling preserve the polished measuring face; avoid hard impacts to keep the geometry intact. Clean using lint-free cloths and approved solvents; do not use abrasives. When integrated into a traceable measurement routine, the M324.001 supports stable control limits and helps to document measurement capability in shop-floor logs and audit reports. For guaranteed traceability and swift supply of this ceramic end gauge, contact Metav Werkzeuge at info@metav-werkzeuge.com or +49 2822 7131930 — our precision specialists will advise and arrange delivery directly Technical data Article number: M324.001 GTIN: 4054469142272 Label: Keramik-Endmaß 1,0mm, Güte 1 DIN 861/1 Category: End gauges Measurements Nominal size: 1.0 mm Weight: 0.001 kg Grade: 1 Customs tariff number: 90173000 Materials & Standards Material: Ceramic Standard: DIN 861/1 Brand: Metav IndustryLine FAQ What does Grade 1 under DIN 861/1 mean for this gauge? Grade 1 indicates a high level of manufacturing precision according to DIN 861/1; the ceramic end gauge M324.001 is made to that standard to serve as a reliable workshop reference for short-range comparisons and verification tasks. Is ceramic suitable for regular workshop use? Yes, ceramic provides thermal stability, hardness and corrosion resistance that make the M324.001 well suited to repeated inspection routines, provided it is handled and stored correctly to avoid impact damage. How should the end gauge be cleaned and stored? Use a lint-free cloth and approved solvent for cleaning; avoid abrasive agents. Store the gauge on a dedicated reference surface or in a padded box to protect the measuring faces and maintain dimensional integrity. Can the ceramic end gauge be used to check micrometers and calipers? The gauge is intended for reference and comparator use and can be employed to corroborate the accuracy of micrometers and calipers in regular inspection cycles, supporting documented measurement procedures. What handling precautions are recommended to preserve accuracy? Limit handling to clean, gloved hands or with suitable tweezers; avoid dropping or striking the gauge. Keep it free from contaminants and return it to protected storage immediately after use to maintain stability. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.1 mm Gauge Block Grade 1 DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of the combination of DIN EN ISO 3650 conformity, Grade 1 tolerance and a hardened special steel construction for consistent verification in inspection routines; order the gauge directly via Metav Werkzeuge or consult the technical advisors for application guidance. End gauge 1.1 mm — DIN EN ISO 3650, Grade 1, hardened special steel A compact, precision end gauge intended for dimensional verification and inspection tasks in laboratories and quality departments, complying with DIN EN ISO 3650 and produced to Grade 1 tolerance. DIN EN ISO 3650, Grade 1 Hardened special steel construction Ideal for fine measurement and verification Compact nominal size for tight tolerances Reliable conformity that simplifies inspection decisions The instrument is manufactured to DIN EN ISO 3650, providing an objective reference for acceptance checks and Go/No‑Go assessments. Built to Grade 1 tolerance, this gauge offers a reproducible reference point for comparative measurements and routine checks on small components. The clear standard compliance reduces interpretation effort during audits and supports consistent decision‑making in production and incoming inspection. Material and handling that improve longevity and repeatability Constructed from hardened special steel, the component resists wear and maintains its geometry over extended use, which reduces replacement frequency and unplanned downtime. The compact format suits fine adjustment and small‑part inspection, while the robust material keeps surface integrity stable under normal workshop handling. Fewer retests are required when a durable reference piece is employed, enhancing throughput in quality control workflows. Practical advantages for quality teams and inspection benches As a precision reference with a 1.1 mm nominal size, this tool integrates easily into existing inspection routines and fixturing where small, explicit reference dimensions are required. The lightweight construction supports swift positioning during batch checks yet retains sufficient rigidity for reproducible results. Traceable production to the cited standard helps to document measurement chains and supports regulatory or customer requirements without introducing complexity. For application advice or to secure this Metav IndustryLine end gauge for inspection kits, contact Metav Werkzeuge and benefit from direct technical guidance from the Emmerich quality centre. Technical data Article number: M319.011.1 GTIN: 4054469130354 Material: Spezialstahl, gehärtet Weight: 0.004 kg Facts Nominal size: 1.1 mm Standard: DIN EN ISO 3650 Cross-section: bis 10mm 30x9mm; ab 10,1mm 35x9mm Tariff number: 90173000 Special features Grade: 1 Category: Endmasse FAQ What is the intended use of this end gauge? The end gauge is designed as a reference for dimensional verification and Go/No‑Go assessments in laboratory and inspection environments; the M319.011.1 supports repeatable checks on small components. Is the material suitable for routine workshop use? Yes, the hardened special steel construction of the M319.011.1 delivers wear resistance appropriate for regular inspection tasks while maintaining dimensional stability. Does this gauge comply with recognised standards? The gauge is produced to DIN EN ISO 3650 and manufactured to Grade 1, providing a clear conformity basis for quality documentation. Can the gauge be used as a master for calibrating other instruments? As a Grade 1 reference, the gauge serves as a stable comparative standard for routine calibration checks; for formal calibration chains, follow organisational procedures. What cross-section applies to this nominal size? For nominals up to 10 mm the cross-section specification is 30×9 mm, as indicated in the technical information for this series. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.1 mm Gauge Block, Grade 0, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of Grade 0 accuracy and a hardened special‑steel construction for dependable reference measurements; the compact cross‑section ensures stable handling during routine checks. Order the single end gauge directly via Metav Werkzeuge or ask the Metav consultants for application advice. Single end gauge 1.1 mm — Grade 0, DIN EN ISO 3650 (Metav IndustryLine) A single end gauge 1.1 mm is a precision reference for dimensional verification in workshop and laboratory metrology, designed as an elementary standard for traceable inspection tasks. Grade 0 accuracy according to DIN EN ISO 3650 Hardened special steel construction Nominal size 1.1 mm for fine calibration Reliable accuracy for routine quality control The gauge provides Grade 0 accuracy under DIN EN ISO 3650, making it suitable as a reference standard for precision inspection and calibration tasks. Because the nominal size is 1.1 mm, the part is particularly useful for verifying small features where minimal deviation is critical. The hardened special‑steel body resists wear during repeated contact checks, which maintains metrological integrity over long service periods and reduces the need for frequent replacement. Compact form that improves handling and repeatability With a compact cross‑section of 30 x 9 mm for sizes up to 10 mm, the gauge is engineered for stable support and low torsion during measurement. The small mass and slim profile help reduce measurement errors caused by awkward positioning, so checks are faster and more repeatable. The straightforward geometry simplifies seating against parts and fixtures, translating the material and form stability directly into improved day‑to‑day efficiency on the inspection bench. Simple integration into verification workflows The end gauge is a practical addition to calibration sets and inspection routines: its nominal 1.1 mm size fits common comparative checks and plug‑gauge tests. As an elemental standard, it supports traceable measurement chains when used alongside calibrated instruments and documented procedures. The clear specification under DIN EN ISO 3650 eases record keeping and helps maintain compliance within established quality‑control systems. For traceable Grade 0 reference work choose the Metav IndustryLine single end gauge and contact Metav Werkzeuge in Emmerich for procurement or tailored measurement advice Technical data Article number: M319.011.0 GTIN: 4054469130347 Tariff number: 90173000 Nominal size: 1.1 mm Accuracy grade: 0 Standard: DIN EN ISO 3650 Material: Special steel, hardened Cross-section (≤10 mm): 30 x 9 mm Weight: 0.004 kg Facts Nominal size: 1.1 mm Weight: 0.004 kg Cross-section dimensions: 30 x 9 mm Tariff number: 90173000 GTIN: 4054469130347 Materials & features Hardened special steel for wear resistance Grade 0 accuracy suitable for reference checks Conforms to DIN EN ISO 3650 Category: End gauges FAQ What tolerance class does this end gauge meet? The single end gauge meets Grade 0 tolerance according to DIN EN ISO 3650 and is intended as a reference standard for fine inspection tasks. Is the material suitable for repeated contact with hardened gauges? Yes, the gauge is manufactured from hardened special steel, which provides good wear resistance for routine comparative checks. Can this gauge be used for calibration records and traceability? Yes, the 1.1 mm end gauge is specified to DIN EN ISO 3650 and is suitable for inclusion in calibration records as a reference artefact. What is the cross‑section for handling and seating? For sizes up to 10 mm the cross‑section is 30 x 9 mm, offering a stable footing for repeatable contact measurements. Which SKU should be ordered for this item? Order item M319.011.0, the single end gauge 1.1 mm from the Metav IndustryLine range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.11 mm Gauge Block Single End, Hardened Special Steel, DIN EN ISO 3650 Grade 0 - Metav IndustryLine
Take advantage of DIN EN ISO 3650 Grade 0 accuracy, a hardened special-steel construction and the compact 1.11 mm nominal size for reproducible calibration and reliable workshop use; order the end gauge directly via Metav Werkzeuge or ask our consultants if needed. Single end gauge 1.11 mm — End gauge, DIN EN ISO 3650 Grade 0 (Metav IndustryLine) A single end gauge 1.11 mm for precision verification and setting tasks in metrology, calibration labs and quality control workflows. DIN EN ISO 3650, Grade 0 accuracy Hardened special steel construction Nominal size 1.11 mm for calibration Reproducible accuracy for calibrated processes The gauge is manufactured to DIN EN ISO 3650 and delivered in Grade 0, guaranteeing a clearly defined tolerance band suitable for high-precision verification. The nominal dimension of 1.11 mm serves as a traceable reference when setting comparators, checking micrometers or referencing master gauges. Specified conformity simplifies documentation in quality procedures and reduces uncertainty in repeated measurements, which supports faster decision-making during production and inspection. Robust material and long service life in daily use Constructed from hardened special steel, the gauge offers high wear resistance and dimensional stability under normal handling. The compact geometry (cross-section 30 × 9 mm for sizes up to 10 mm) provides a solid feel and resists bending during routine use. Low mass and ergonomic edges improve handling when placing and removing the reference, while the surface finish eases cleaning and prevents contamination that could affect readings. These attributes help maintain the reference value over many inspection cycles. Direct benefits and typical applications in industry As a fixed nominal reference, this gauge reduces setup time when calibrating hand tools or machine-mounted measuring devices, improving throughput in workshop and laboratory environments. Typical applications include calibration benches, comparator settings, tool presetting and traceable checks within inspection routines. The combination of standard conformity and durable construction ensures consistent results across shifts and operators, supporting reproducible quality control in metalworking and precision engineering contexts. For procurement or technical clarification regarding the Metav IndustryLine end gauge, contact Metav Werkzeuge in Emmerich for expert advice and reliable supply — info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M319.0111.0 Manufacturer: Metav IndustryLine GTIN: 4054469130361 Facts Nominal size: 1.11 mm Weight: 0.004 kg Cross-section (≤10 mm): 30 × 9 mm Special features Material: special steel, hardened Standard: DIN EN ISO 3650 Grade: 0 Tariff code: 90173000 FAQ What tolerance class does this gauge conform to? The gauge is delivered as a Grade 0 reference according to DIN EN ISO 3650, ensuring a narrow tolerance suitable for precise verification tasks with the single end gauge 1.11 mm. Is the material suitable for frequent workshop use? Yes — the single end gauge 1.11 mm is made from hardened special steel, which provides high wear resistance and dimensional stability during repeated handling. Can this gauge be used to set micrometers and comparators? The gauge is intended as a fixed nominal reference and is well suited for setting micrometers, comparators and other workshop standards where a 1.11 mm reference is required. What are the physical dimensions relevant for handling? For nominal sizes up to 10 mm the cross-section is 30 × 9 mm; the compact form factor and low weight support safe, repeatable placement. How should the gauge be stored to preserve accuracy? Store the gauge clean, dry and protected from mechanical shocks; regular checks against a master standard are recommended to document continued conformity of the end gauge 1.11 mm. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.11 mm Gauge Block, Hardened Special Steel, DIN EN ISO 3650 Grade 1 - Metav IndustryLine
Take advantage of proven metrology standards and compact handling: a DIN EN ISO 3650 Grade 1 gauge, manufactured from hardened special steel and finished to a nominal size of 1.11 mm, provides a stable reference for calibration and routine checks. Order this precision gauge directly via Metav Werkzeuge or consult the Metav specialists for procurement advice. End gauge 1.11 mm — Gauge block to DIN EN ISO 3650, Grade 1 (Metav IndustryLine) The End gauge 1.11 mm is a precision gauge block intended as a traceable reference in laboratory and workshop quality control for dimensional inspection and tool setting. DIN EN ISO 3650 Grade 1 accuracy Hardened special steel construction Nominal size 1.11 mm for fine reference checks Reliable reference for calibration and quality control Manufactured to DIN EN ISO 3650 and rated Grade 1, this gauge block serves as a stable, high‑quality reference for dimensional verification and calibration tasks. The Grade 1 classification signals a level of geometric and dimensional consistency suitable for laboratory and industrial metrology where repeatable measurements reduce uncertainty. The small nominal size of 1.11 mm makes this block particularly useful when setting up comparators, verifying micrometre carriers or checking fine features on parts; the component functions as a compact standard that integrates seamlessly into existing measurement routines. Emphasis on standard conformity supports quality documentation and helps maintain process reliability. Robust design that supports frequent handling Constructed from hardened special steel, the block combines wear resistance with a compact cross‑section appropriate for small reference gauges. The cross‑section dimension applicable to this nominal size is 30 x 9 mm, providing a stable contact area while keeping the piece lightweight for convenient handling. The material selection and heat treatment increase service life and resistance to surface damage, which in turn lowers the need for frequent replacement and helps ensure consistent contact geometry over time. Such durability benefits throughput and reduces interruptions in production and inspection workflows. Seamless inclusion in procurement and inventory systems This precision block is supplied with a clear product identity for logistical and quality‑management processes: GTIN and SKU are assigned for stock control, and the manufacturer designation links the item to Metav IndustryLine’s quality assurance channel. Using standardised reference blocks simplifies traceability between measurement results and production decisions, supporting compliance and audit requirements. For procurement managers and quality engineers, the combination of internationally recognised standard adherence and a compact reference size minimises administrative effort while delivering the technical reliability expected in industrial metrology. For assured reference measurements, specify the Metav IndustryLine End gauge 1.11 mm and contact Metav Werkzeuge in Emmerich for tailored procurement support and technical clarification via info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M319.0111.1 GTIN: 4054469130378 Manufacturer: Metav IndustryLine Material: Spezialstahl, gehärtet Nominal size: 1.11 mm Standard: DIN EN ISO 3650 Grade: 1 Category: Endmasse Tariff number: 90173000 Facts Nominal size: 1.11 mm Weight: 0.004 kg Cross-section: 30 x 9 mm GTIN: 4054469130378 Special features Hardened special steel Manufactured to DIN EN ISO 3650 Grade 1 accuracy SKU: M319.0111.1 FAQ What applications is this gauge block suited for? The End gauge 1.11 mm from Metav IndustryLine is suited for calibration, comparator setting and fine dimensional checks in laboratory and workshop quality control. Is the material suitable for frequent use? Yes, the gauge block is made from hardened special steel which gives the End gauge 1.11 mm good wear resistance for regular inspection tasks. Which standard does the gauge comply with? This gauge block is manufactured to DIN EN ISO 3650 and delivered as Grade 1, ensuring conformity with common metrology requirements. How is the product identified for inventory and traceability? The item is listed under SKU M319.0111.1 and GTIN 4054469130378, facilitating stock control and traceability within quality systems. Can this gauge be used in calibration laboratories? Its Grade 1 classification and DIN EN ISO 3650 conformity make the End gauge 1.11 mm appropriate as a reference in many calibration and laboratory contexts. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.11mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of a ceramic reference body combined with Grade 1 tolerance for a stable, compact length standard. The combination of 1.11 mm nominal size and ceramic construction supports reproducible comparative measurements and routine reference tasks. Order the ceramic gauge block directly via Metav Werkzeuge or ask our consultants if needed. Ceramic Gauge Block 1.11 mm — Grade 1 (DIN 861/1) | Metav IndustryLine The Ceramic Gauge Block 1.11 mm is a compact, high‑stability length standard designed as a precise reference for workshop and laboratory metrology applications Ceramic construction for dimensional stability Grade 1 accuracy according to DIN 861/1 Nominal length 1.11 mm, compact reference Reliable accuracy for routine reference measurements As a Grade 1 length standard under DIN 861/1, this ceramic gauge block provides a dependable reference for comparative checks and daily inspection routines. The 1.11 mm nominal dimension is held within tight tolerances appropriate for workshop calibration and quality control, giving a clear technical basis for comparative gauging, plug checks and assembly verification. The block’s consistency in size supports repeatable setups on comparators and surface plates, reducing uncertainty in frequent checks and simplifying decision‑making in production control. Long‑term stability from ceramic construction Made of high‑performance ceramic, the block offers inherent resistance to wear and dimensional drift compared with softer materials. The material’s low thermal expansion and corrosion resistance contribute to dimensional stability across normal workshop temperature variations, which helps maintain reference performance between periodic verifications. For measuring tasks where contact wear and surface integrity matter, the ceramic surface reduces abrasion and maintains gauge geometry for extended service life, supporting fewer replacements and steadier process control. Compact format and clear identification for inventory and use The compact design and light mass make the block easy to handle and integrate into existing inspection routines without excessive fixturing. Identifiers such as SKU M324.001.11 and GTIN 4054469142487 enable straightforward inventory tracking and traceability in procurement systems. The small footprint makes the item convenient as part of a set of reference blocks or as an individual standard for specialised checks, while offering a robust reference for precise assembly and small‑part inspection workflows. For a dependable Grade 1 ceramic reference, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 to discuss suitability for specific metrology tasks. Technical Data Article number: M324.001.11 GTIN: 4054469142487 Customs tariff number: 90173000 Facts Nominal length: 1.11 mm Weight: 0.001 kg Quality grade: 1 Special features Material: Ceramic Standard: DIN 861/1 Category: Gauge block (Endmasse) FAQ What tolerance class does this gauge block meet? The Ceramic Gauge Block 1.11 mm is manufactured to Grade 1 in accordance with DIN 861/1, providing the tolerance class required for many workshop and inspection tasks. Why choose a ceramic gauge block over a metal alternative? The ceramic construction of this gauge block offers improved dimensional stability and enhanced wear resistance compared with many metals, helping to keep the reference size steady under normal workshop conditions. Can this block be used as part of a set for comparator checks? Yes, the compact 1.11 mm block is suitable as an individual reference or combined within sets for comparative measurements on comparators and inspection benches. How should the Ceramic Gauge Block 1.11 mm be handled to preserve accuracy? Handle with clean, dry hands or tweezers and store in a clean, dry case; avoid abrasive contact and keep the reference free from oils and contaminants to preserve surface integrity and dimensional performance. Which identifiers help to order or log this item in an ERP system? Reference SKU M324.001.11 and GTIN 4054469142487 when ordering or recording the ceramic gauge block in procurement and inventory systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.12 mm Gauge Block Single, Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of Grade 0 accuracy, a hardened special‑steel construction and a compact cross‑section for a stable, long‑lasting reference standard; order the gauge block directly via Metav Werkzeuge or contact our consultants for specification support. Single gauge block 1.12 mm (DIN EN ISO 3650) — Metav IndustryLine, Grade 0, hardened special steel Single gauge block 1.12 mm for use as a precision length standard in inspection, calibration and laboratory environments Grade 0 accuracy to DIN EN ISO 3650 Hardened special‑steel construction Nominal length 1.12 mm for precise stacks 30 x 9 mm cross‑section for stable handling Consistent Grade 0 performance for traceable length standards The single gauge block is manufactured to DIN EN ISO 3650 in Grade 0, delivering a defined tolerance class for reliable reference measurements. The nominal 1.12 mm dimension and carefully controlled geometry permit the formation of wrung stacks to establish a range of lengths from a compact set. This conformity to an international standard supports repeatable measurement routines and reduces uncertainty in routine inspection and quality control processes. Durable construction that maintains accuracy over time Constructed from hardened special steel, the block resists wear and preserves contact surfaces during repeated use. The compact 30 x 9 mm cross‑section offers a balance of handling stability and minimal thermal mass, which helps to limit dimensional drift during short measurement cycles. The robust finish and material selection ensure the block remains a dependable reference across many calibration cycles, providing measurable value in production and laboratory settings. Practical integration with existing gauge sets and workshop workflows The block’s standardised dimensions and Grade 0 tolerance make it suitable for integration into established gauge block sets and comparative measurement procedures. Its small footprint simplifies storage and stacking while the flat, precision surfaces enable secure wringing behaviour when combined with other calibrated blocks. As a purpose‑made length standard, the item supports efficient setup of comparative gauges and micrometre checks without complex ancillary equipment. Reliability and supply backed by Metav’s quality filter Sourcing this length standard from Metav IndustryLine benefits from Metav’s role as a quality filter for the European market. With decades of experience and a broad product range, Metav provides consistent availability and selection for workshops and laboratories seeking dependable metrology equipment. The combination of a trustworthy supplier and a Grade 0, hardened reference component helps to secure reproducible measurement results and long‑term operational reliability. Contact Metav Werkzeuge for detailed technical matching and to secure this Grade 0 length standard from Metav IndustryLine Technical Data Article number: M319.0112.0 GTIN: 4054469130385 Material: Hardened special steel Nominal length: 1.12 mm Accuracy grade: 0 Standard: DIN EN ISO 3650 Weight: 0.004 kg Cross‑section: 30 x 9 mm Facts Nominal length: 1.12 mm Weight: 0.004 kg Cross‑section: 30 x 9 mm Tariff number: 90173000 GTIN: 4054469130385 Special features Conforms to DIN EN ISO 3650 Grade 0 tolerance class Hardened special‑steel construction Compact cross‑section for stable handling Intended as a precision length standard for calibration and inspection FAQ What tolerance class does this gauge block meet? The single gauge block meets Grade 0 tolerances in accordance with DIN EN ISO 3650, providing defined limits for precision measurement. Is the block suitable for wringing and stacking? Yes. The precision ground faces and standardised geometry enable wringing behaviour so the block can be combined with other blocks to create exact lengths for comparative measurement. What is the nominal dimension and cross‑section of the item? The nominal dimension is 1.12 mm and the cross‑section for this size is 30 x 9 mm, making it compact yet stable for handling. Which material is used and how does it affect durability? The gauge block is made from hardened special steel, which enhances surface wear resistance and helps preserve measurement accuracy over repeated use. Can this block be used as a reference in calibration routines? The block is designed as a precision length standard and, given its Grade 0 conformity, is suitable for comparative calibration tasks; for accredited calibration services, request the appropriate certificate from the calibration provider Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.12 mm Gauge Block, DIN EN ISO 3650 Grade 1, Hardened Special Steel - Metav IndustryLine
Take advantage of certified precision and a wear‑resistant, hardened steel construction to secure repeatable reference measurements; order the gauge block directly via Metav Werkzeuge or consult our specialists for application advice. Gauge block 1.12 mm — Grade 1, hardened special steel (DIN EN ISO 3650) | Metav IndustryLine The gauge block 1.12 mm is a high‑precision reference standard for calibration and dimensional inspection in laboratory and workshop metrology. DIN EN ISO 3650, Grade 1 Hardened special steel construction Nominal length 1.12 mm reference Cross-section 30×9 mm for compact sizes Measurement certainty for routine calibration and quality control Compliance with DIN EN ISO 3650 and classification as Grade 1 provide a verifiable basis for traceable calibration work and routine inspection tasks. The nominal length of 1.12 mm serves as a stable reference that reduces measurement uncertainty across inspection routines, enabling faster decision‑making in quality assurance. Where repeatability matters, the standard conformity supplies objective evidence for audits and process control, making the component suitable for accredited laboratories and in‑house gauge sets alike. Robust material for long service life and low maintenance Manufactured from hardened special steel, the reference block offers high wear resistance and dimensional stability under normal workshop handling. The chosen material minimises surface abrasion during repeated wringing and avoids micro‑deformation that would otherwise compromise long‑term accuracy. As a result, lifecycle costs are reduced through extended intervals between inspection and replacement, while daily handling remains straightforward thanks to the compact mass and form. Compact form factor that simplifies handling and stacking For nominal lengths up to 10 mm, the compact cross‑section (30×9 mm) ensures easy stacking, fast selection from sets and reliable wringing behaviour on flat reference surfaces. The small footprint supports efficient bench layout and rapid sequence checks without sacrificing ergonomics during manual operation. Clear, reproducible seating and a stable geometry make this format particularly suitable for calibration benches and mobile test rigs where space and repeatability are both critical. Practical advantages for workshop integration Integration into measurement routines is simplified by the block's standardised dimensions and conformity with industry practice for gauge blocks. The modest weight and compact geometry make it straightforward to combine this reference with other blocks in a slip gauge set, while the Grade 1 accuracy supports typical workshop and inspection tasks that demand certified references. The product is designed to support throughput and traceability in production environments, contributing to smoother workflows and reliable inspection records. Select the Metav IndustryLine gauge block for dependable reference measurements and contact Metav Werkzeuge in Emmerich for tailored advice and delivery coordination via info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: M319.0112.1 GTIN: 4054469130392 Standard: DIN EN ISO 3650 Grade: 1 Facts Nominal length: 1.12 mm Weight: 0.004 kg Cross-section (≤10 mm): 30×9 mm Customs tariff number: 90173000 Special features Material: Special steel, hardened Category: Gauge blocks (Endmasse) Suitable for calibration and dimensional inspection FAQ What level of accuracy can be expected from this block? The gauge block 1.12 mm (Metav IndustryLine, SKU M319.0112.1) is manufactured to DIN EN ISO 3650 Grade 1, providing a stable reference suitable for routine calibration and inspection tasks. Is the material resistant to regular wringing and handling? Yes, the hardened special steel construction of the gauge block offers high wear resistance and preserves dimensional stability during repeated wringing and use. Can this block be used in a standard slip gauge set? The compact cross‑section (30×9 mm for sizes up to 10 mm) makes the block fully compatible with common slip gauge sets and facilitates efficient stacking and combination. Is the block suitable for workshop quality control rather than only lab use? Grade 1 conformity allows the gauge block to serve both workshop quality control and laboratory calibration where traceable reference standards are required. How is traceability documented for this reference piece? Traceability is supported by its compliance with DIN EN ISO 3650; further documentation can be provided via Metav Werkzeuge on request. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.12mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the combination of Grade 1 accuracy and a compact 1.12 mm nominal length in a wear‑resistant ceramic construction for dependable length standards; order the Ceramic gauge block 1.12 mm, Grade 1 (DIN 861/1) directly via Metav Werkzeuge or ask our consultants if needed. Ceramic gauge block 1.12 mm, Grade 1 (DIN 861/1) — Metav IndustryLine A Ceramic gauge block 1.12 mm, Grade 1 (DIN 861/1) that serves as a compact, high‑precision length standard for calibration and reference measurement in metrology and quality control. Grade 1 accuracy (DIN 861/1) Wear-resistant ceramic construction Nominal length 1.12 mm Weight 0.001 kg, compact and precise Consistent reference performance for metrology tasks This Grade 1 gauge block is specified to DIN 861/1, delivering a reproducible length standard for laboratory and workshop reference tasks. The 1.12 mm nominal size provides a precise datum for setting instruments and verifying small assembly features; its small footprint supports integration into calibration sets and gauge stacks. By adhering to an established standard, the block supports measurement routines that demand traceability and comparable results across inspection setups. Material choice that supports longevity and dimensional stability Manufactured from ceramic, the block combines low wear with a stable reference surface, making it suitable for repeated comparison measurements and as a master reference in environments where surface durability matters. The ceramic material is chosen to reduce surface degradation over time while maintaining a consistent contact face for tactile gauges and optical comparators. The low mass and compact geometry aid handling during short, precise adjustments, reducing the risk of accidental deformation. Practical use: where small precision matters As a compact reference element, this gauge block is intended for precision tasks such as small‑part inspection, fixture verification and fine‑mechanical assembly control. Its compact nominal length of 1.12 mm makes it ideal for creating short gauge stacks or checking instrument zero points without occupying excessive bench space. Lightweight at 0.001 kg, the block is easy to manoeuvre when composing stacks or aligning with measurement surfaces, supporting efficient workflows in both production sampling and quality labs. Contact Metav Werkzeuge for application advice and to secure this Grade 1 ceramic gauge block for precision reference tasks at your facility Technical Data Article number: M324.001.12 GTIN: 4054469142494 Tariff number: 90173000 Manufacturer: Metav IndustryLine Category: Endmasse Facts Nominal length: 1.12 mm Weight: 0.001 kg Grade: 1 (DIN 861/1) Special features Material: Ceramic Intended use: Precision length standard / gauge block SKU: M324.001.12 FAQ What is the nominal length of this gauge block? The Ceramic gauge block 1.12 mm, Grade 1 (DIN 861/1) has a nominal length of 1.12 mm. Which material is used for the block? The Ceramic gauge block 1.12 mm, Grade 1 (DIN 861/1) is manufactured from ceramic. To which standard does this product conform? The block meets DIN 861/1 requirements as a Grade 1 gauge block. How much does the gauge block weigh? The Ceramic gauge block 1.12 mm, Grade 1 (DIN 861/1) has a weight of 0.001 kg. What are typical applications for this gauge block? The Ceramic gauge block 1.12 mm, Grade 1 (DIN 861/1) is used as a reference length in calibration sets, small‑part inspection and precision assembly checks Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.13 mm Gauge Block Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of the combination of Grade 1 tolerance and hardened special steel for reliable, repeatable dimensional checks; the nominal 1.13 mm size suits fine-pitch inspection tasks. Order this end gauge directly via Metav Werkzeuge or consult our specialists for application advice. End gauge 1.13 mm (DIN EN ISO 3650) — Grade 1 precision by Metav IndustryLine The End gauge 1.13 mm (DIN EN ISO 3650) is a compact, hardened limit gauge designed for precise dimensional verification in inspection, assembly and quality-control workflows. DIN EN ISO 3650, Grade 1 tolerance Hardened special steel construction Nominal size 1.13 mm for precision checks Reliable accuracy for strict tolerances This Grade 1 limit gauge provides a clear reference for acceptance testing where tight tolerances matter. Compliance with DIN EN ISO 3650 ensures interchangeability with other standard gauges and supports consistent pass/fail decisions on the production line. The nominal 1.13 mm size is manufactured to close dimensional limits, reducing ambiguity in go/no‑go assessments and enabling faster quality decisions without lengthy measurement chains. Robust material and stable geometry for repeatable readings Manufactured from hardened special steel, the gauge resists wear and maintains form over repeated use, which preserves measurement integrity and minimises rework. The specified cross‑section (30×9 mm or 35×9 mm depending on size) contributes to stable seating in fixtures and reduces flex during engagement. Such mechanical stability translates into repeatability in inspection routines and a lower rate of false rejects, improving throughput in routine quality checks. Practical handling and integration into workflows The compact design and low mass make the gauge easy to manipulate in bench or fixture-based tests while keeping handling errors low. The slim profile suits confined inspection points and can be incorporated into custom jigs or assembly gauges as a hard reference. Clear marking of nominal size and standard compliance simplifies documentation and traceability in inspection records, supporting efficient process audits. Trusted supply and precision service Sourcing from a known precision range like Metav IndustryLine combines product consistency with logistics reliability. The Metav approach focuses on making high-precision tools accessible to workshops and production facilities, backed by a broad catalogue and dependable fulfilment from Emmerich. Choosing this limit gauge supports a measured, long-term quality strategy and reduces vendor complexity for procurement teams. Contact Metav Werkzeuge to discuss fitment options for the Metav IndustryLine end gauge or to reserve stock for upcoming inspection cycles Technical Data Article number: M319.0113.1 GTIN: 4054469130415 Label: Endmaß 1,13 mm, DIN ISO 3650, Güte 1 DIN ISO 3650 Facts Nominal size: 1.13 mm Weight: 0.004 kg Cross-section: until 10 mm → 30 × 9 mm; from 10.1 mm → 35 × 9 mm Tariff number: 90173000 Special features DIN EN ISO 3650 compliance Grade 1 tolerance Material: special steel, hardened Category: End gauges FAQ What tolerance class does this limit gauge follow? The end gauge conforms to Grade 1 tolerance under DIN EN ISO 3650, providing a high level of dimensional certainty for pass/fail testing. Is the gauge suitable for repeated use in production environments? Yes, the gauge’s hardened special steel construction and robust cross‑section are designed to withstand frequent engagement and preserve dimensional integrity. What is the nominal dimension and how is it marked? The nominal dimension is 1.13 mm; the gauge is labelled with the nominal size and standard designation for easy identification during inspection routines. Can this gauge be used in fixture-mounted checks? The slim profile and defined cross‑section make the gauge practical for incorporation into fixtures or jigs as a fixed reference for go/no‑go verifications. Which SKU identifies this product for ordering? This item is listed as SKU M319.0113.1 in the Metav IndustryLine range for catalogue and procurement reference. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
ensure traceable length calibration with gauge blocks
gauge blocks, also called slip gauges or end gauges, are precision length standards designed to transfer exact measures during calibration and setup. Manufactured and graded for metrological use, they provide the reference dimensions needed to verify and adjust measuring instruments in industrial workshops and calibration labs.
how gauge blocks work and where they are essential
gauge blocks are used to create known lengths by wringing individual blocks together or by using a single block as a reference. length calibration in industry commonly relies on parallel gauge blocks, while angle, cylinder and sphere end gauges serve specialised tasks. these blocks are produced in steel, ceramic or carbide, and their material choice balances wear resistance with thermal behaviour. regular calibration—typically performed annually—by DAkkS-accredited laboratories ensures traceability. the highest-precision reference work, class K, is certified by the PTB using laser techniques; classes 0, 1 and 2 are tested under progressively less controlled conditions (class 0 in a climate-controlled lab, class 1 in a standard measurement room, class 2 in production).
measurable benefits that cut downtime and uncertainty
- consistent, traceable length standards reduce rework and measurement disputes by enabling reliable instrument calibration.
- choosing the correct material (steel, ceramic, carbide) extends service life and limits wear in high-use environments.
- selecting the right accuracy class (K, 0, 1 or 2) matches calibration effort to application needs and avoids over‑specification.
- annual calibration by accredited labs maintains documented compliance and supports quality systems such as ISO.
why Metav is a smart partner for precision standards
Metav combines specialist knowledge with a broad range of measurement technology, making the procurement of gauge blocks straightforward and dependable. with over 48,000 customers and more than 250,000 products stocked from Emmerich, Metav acts as a pragmatic quality filter for European workshops, reducing supplier complexity and ensuring consistent supply.
In short, gauge blocks deliver traceable, material‑appropriate and class‑matched references that keep calibration workflows efficient and auditable.
faq
what materials are gauge blocks available in and why does it matter?
gauge blocks are typically supplied in steel, ceramic or carbide. material choice affects wear resistance, stability and thermal expansion; selecting the right material for your environment optimises longevity and measurement stability.
how often should gauge blocks be calibrated?
industry practice is an annual calibration cycle, carried out by DAkkS-accredited laboratories, though frequency can be increased depending on usage and required uncertainty.
what do the accuracy classes k, 0, 1 and 2 indicate?
the classes denote graded tolerances and test conditions: K is the highest precision (certified by PTB with laser measurement), class 0 is checked under climate-controlled lab conditions, class 1 in a normal measurement room and class 2 in production environments.
are parallel gauge blocks always used for length calibration?
yes; for length calibration the parallel gauge blocks are the primary standard because they provide exact planar faces for wringing and stacking to create precise lengths.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com