End gauges for precise length calibration
End gauges provide exact reference lengths for calibrating measurement instruments and ensuring consistent dimensional accuracy in metalworking and inspection processes. Used in production and laboratory settings, these end gauges—made from steel, ceramic or carbide—allow technicians to compensate for wear and thermal effects and maintain measurement traceability, especially when employed alongside parallel end gauges, cylinder gauges and calibration masters. Classes 0, 1 and 2 define practical tolerance levels for workshop, inspection-room and production use respectively, delivering the repeatable precision required for machining and quality control.
1.21 mm Gauge Block Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
The combination of Grade 1 accuracy, hardened special steel construction and compact mass ensures reliable, repeatable measurements in inspection and calibration tasks. Benefit from a standard-compliant gauge that supports consistent quality control — order the end gauge directly via Metav Werkzeuge or ask our consultants for application advice. End gauge 1.21 mm — Grade 1, DIN EN ISO 3650 (Metav IndustryLine) The End gauge 1.21 mm is a precision inspection gauge for dimensional verification and calibration tasks in metrology and manufacturing. DIN EN ISO 3650 Grade 1 tolerance Hardened special steel construction Compact mass: 0.005 kg for stable handling Cross-section 30 x 9 mm for sizes ≤ 10 mm Precision that supports trustworthy decisions Manufactured to DIN EN ISO 3650 and rated Grade 1, this precision end gauge delivers a narrowly defined tolerance band that underpins objective pass/fail decisions in production and lab environments. The nominal size of 1.21 mm is produced with tight dimensional control, enabling it to serve as a reference for small-feature inspection or as a member of a master gauge set. The combination of standard conformity and measurable specification reduces ambiguity during inspections and offers a clear technical basis for quality documentation. Built for repeatability and long service life Constructed from hardened special steel, the gauge resists wear and maintains its form through repeated contact with measured parts. The specified cross-section of 30 x 9 mm (applicable for sizes up to 10 mm) provides a balance between rigidity and ease of handling, keeping deformation and thermal influence minimal during use. Low mass (0.005 kg) contributes to reduced thermal drift and simple positioning on fine parts, supporting reproducible measurements with less operator-induced variability. Integrates cleanly into quality workflows This precision gauge is designed for straightforward inclusion in inspection routines and gauge sets; its traceable identifiers support inventory control and documentation. The product is listed with GTIN and customs tariff information to simplify logistics and compliance in procurement processes. As a standardised measuring tool, it complements comparators, microscope-assisted checks and manual gauge benches, providing a compact, reliable reference for small-diameter verification tasks. Metav IndustryLine: reliable precision, practical availability Metav IndustryLine supplies this gauge as part of a broad precision portfolio intended to make high-quality metrology accessible to workshops and quality departments. With a staging and quality filter in Emmerich, Metav ensures consistent order fulfilment and product checks for the European market. The result is a durable Grade 1 measuring tool supported by a supplier network experienced in precision equipment for industry and trade. For Grade 1 verification and application guidance, request product and technical support from Metav Werkzeuge — contact info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability for specific inspection tasks. Technical data Article number: M319.0121.1 GTIN: 4054469130576 Customs tariff number: 90173000 Numeric specifications Nominal size: 1.21 mm Weight: 0.005 kg Cross-section: 30 x 9 mm (for sizes ≤ 10 mm) Material & standards Material: Special steel, hardened Standard: DIN EN ISO 3650 Grade: 1 Category: End gauges FAQ What accuracy class does this gauge comply with? The End gauge 1.21 mm complies with DIN EN ISO 3650 and is supplied as Grade 1, providing a defined tolerance range suitable for standard precision inspection. Which material is the gauge made from and why? The gauge is made from hardened special steel, chosen for wear resistance and dimensional stability under normal inspection conditions; this ensures longevity of the reference size. Can this gauge be used within a master set for small-part verification? Yes, the End gauge 1.21 mm is intended for inclusion in gauge sets and serves as a compact reference for small-diameter checks and comparative inspection routines. How does the cross-section affect handling and stability? The 30 x 9 mm cross-section (for sizes up to 10 mm) provides stiffness that minimises bend and deformation while remaining manageable for manual placement on small features. What identifiers aid in procurement and inventory control? The product is listed with GTIN 4054469130576 and the article number M319.0121.1 to support traceability and logistical handling. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.21 mm Gauge Block Single End, Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of Grade 0 accuracy under DIN EN ISO 3650 and the durable special hardened steel construction to establish a stable reference point for dimensional checks. Order the part directly via Metav Werkzeuge or consult the Metav team for application-specific advice. Single gauge block 1.21 mm — Grade 0 calibration standard by Metav IndustryLine The Single gauge block 1.21 mm serves as a precision reference for dimensional calibration and comparison tasks in inspection benches and quality-control fixtures. Grade 0 accuracy to DIN EN ISO 3650 Hardened special steel construction Nominal size 1.21 mm with tight tolerance Compact weight 0.005 kg for easy handling Accuracy that makes routine checks reliable A Grade 0 reference defined by DIN EN ISO 3650 provides a predictable baseline for laboratory measurements and in-process verification. The nominal dimension of 1.21 mm is produced and finished to tight tolerances, so the block functions as a stable reference standard for comparative gauging or for verifying measuring instruments. This level of precision reduces uncertainty in acceptance testing and supports reproducible results across inspection cycles. Robust material and compact handling for long service life Manufactured from special hardened steel, the block resists wear and surface damage during repeated handling and stacking. The compact mass of 0.005 kg and the defined cross-section ensure comfortable manipulation and minimal influence on thermal drift during short-term measurements. The material choice balances hardness with dimensional stability, helping to preserve the calibrated surface over sustained use and thereby lowering lifetime maintenance needs. Seamless integration into quality workflows As a single block intended for use in sets or as an individual reference, this item supports traceable measurement chains and instrument checks. Identification via SKU M319.0121.0 and GTIN allows straightforward inventory control and documentation inside calibration management systems. The combination of normative compliance, durable construction and compact handling streamlines daily metrology tasks, making this reference suitable for calibration laboratories, toolrooms and production quality departments. Contact Metav Werkzeuge to discuss how this Grade 0 gauge block fits specific calibration plans and to arrange supply directly from Emmerich. Technical data SKU: M319.0121.0 GTIN: 4054469130569 Article: Single gauge block 1.21 mm, DIN EN ISO 3650, Grade 0 Facts Nominal size: 1.21 mm Weight: 0.005 kg Tolerance grade: 0 (Grade 0) Tariff number: 90173000 Cross-section: up to 10 mm → 30 x 9 mm; from 10.1 mm → 35 x 9 mm Special features Material: special hardened steel Standard: DIN EN ISO 3650 Category: Gauge blocks Application: precision dimensional reference FAQ What level of tolerance does this gauge block provide? This gauge block is manufactured to Grade 0 tolerance according to DIN EN ISO 3650, offering a high-precision reference suitable for calibration and comparative measurements; identification: M319.0121.0 by Metav IndustryLine. Which material is used and what are the benefits? The block is made from special hardened steel, providing wear resistance and dimensional stability for repeated handling and long-term use in inspection and calibration environments. For which applications is this reference most suitable? The product is intended for calibration benches, quality control checks, assembly into gauge sets and comparative gauging where a fixed, normative reference is required. Can this block be used alone or as part of a set? The single gauge block is suitable both as an individual reference and as a component in precision gauge sets; its compact form factor and standard dimensions facilitate stacking and set assembly. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.21mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the combination of ceramic construction, Grade 1 accuracy (DIN 861/1) and a compact 1.21 mm nominal length for reliable reference measurement in the workshop or laboratory; order the gauge block directly via Metav Werkzeuge or ask their consultants for tailored advice. Ceramic gauge block 1.21 mm, Grade 1 (DIN 861/1) — Metav IndustryLine The Ceramic gauge block 1.21 mm is a compact length standard designed for high-stability reference measurements and calibration checks in metrology and precision engineering. Ceramic construction for thermal stability Grade 1 accuracy to DIN 861/1 Nominal length 1.21 mm for fine calibration Extremely low mass: 1 g facilitates delicate use Consistent, repeatable reference for production and inspection The Grade 1 tolerance specified by DIN 861/1 ensures the block performs as a dependable reference in routine verification and comparative measurements. With a nominal length of 1.21 mm, the item is suited to fine adjustments and small-gap checks where repeatability matters. The specified grade indicates established production tolerances, which helps quality departments maintain traceable control of measuring instruments and fixtures. Material advantages that reduce measurement uncertainty Made from ceramic, the block offers superior thermal stability and excellent wear resistance compared with many metallic standards. Ceramic’s low coefficient of thermal expansion limits length variation with temperature changes, so batch checks and short-term comparisons remain consistent. The material is also largely non-magnetic, which avoids interaction with magnetic fixtures and helps preserve surface integrity over repeated use. Practical handling and integration in the workshop Thanks to its compact size and lightweight construction, the block integrates easily into existing gauge sets, comparator fixtures and precision toolrooms. The small mass reduces stress on delicate clamping arrangements and makes the standard convenient for portable inspection kits. As part of a set of grade-rated blocks, this piece contributes to a modular approach to length standards, supporting efficient metrology workflows and fewer measurement interruptions. Contact Metav Werkzeuge today to secure this Metav IndustryLine ceramic gauge block for Grade 1 reference work, or consult the Metav team in Emmerich for application-specific recommendations via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M324.001.21 GTIN: 4054469142586 Tariff number: 90173000 Material: Ceramic Nominal length: 1.21 mm Weight: 0.001 kg Grade: 1 (DIN 861/1) Facts Nominal length: 1.21 mm Weight: 0.001 kg Grade: 1 Tariff code: 90173000 Special features Ceramic material Grade 1 tolerance per DIN 861/1 Category: Gauge blocks (Endmasse) Manufacturer brand: Metav IndustryLine FAQ What level of precision does this gauge block offer? The ceramic gauge block 1.21 mm is manufactured to Grade 1 per DIN 861/1, providing a stable and repeatable reference suitable for workshop inspections and comparator checks. Can this block be used as a reference for calibrating callipers and micrometres? Yes, the Metav IndustryLine ceramic gauge block is intended as a length standard for comparative calibration of callipers, micrometres and other measuring instruments. How should the ceramic gauge block be cared for to preserve accuracy? Handle the M324.001.21 with clean, dry hands or gloves, avoid knocks and abrasions, and store it in a dry, temperature‑stable environment to maintain its surface and dimensional stability. Is the ceramic material magnetically neutral and chemically stable? Ceramic is largely non-magnetic and chemically inert, making the gauge block suitable for use where magnetic interaction or corrosion would otherwise affect measurements. Is the block suitable for use on a mobile inspection bench or in a fixed laboratory setup? The low mass and compact dimensions of the ceramic gauge block make it adaptable to both portable inspection kits and fixed laboratory comparators, serving as a precise short-length reference. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.22 mm Gauge Block Grade 1 DIN EN ISO 3650 Hardened Special Steel - Metav IndustryLine
Take advantage of DIN EN ISO 3650 conformity and the Grade 1 accuracy to secure repeatable inspection results; the hardened special-steel construction ensures stable metrological reference points and long service life. Order the end gauge directly via Metav Werkzeuge or ask our consultants if needed. End gauge 1.22 mm — Limit gauge, DIN EN ISO 3650, Grade 1 (Metav IndustryLine) The End gauge 1.22 mm is a hardened special‑steel limit gauge intended for precise dimensional verification and workshop inspection tasks in industrial metrology. DIN EN ISO 3650 compliance, Grade 1 Hardened special steel construction Compact, lightweight precision gauge Suitable for workshop and lab inspection Traceable inspection standard for reliable decision-making The gauge follows DIN EN ISO 3650, delivering a certified reference point with Grade 1 tolerance for critical inspection operations. As a dedicated small‑format limit gauge it provides a clear, objective pass/fail criterion during incoming inspection or final checks, reducing ambiguity in measurement decisions. The nominal size of 1.22 mm is presented as a stable, calibrated dimension that supports consistent quality control workflows. Robust materials for stable measurements over time Manufactured from hardened special steel, the component resists wear and maintains form stability through repeated contact checks. The compact mass and controlled geometry lower the risk of deformation, so the gauge remains a dependable standard in daily use. The combination of material choice and finishing reduces maintenance cycles and assures prolonged dimensional fidelity under typical workshop conditions. Designed for practical use in workshop and laboratory environments The slim profile and low weight make the gauge straightforward to handle and store while still delivering industrial‑grade precision. Its construction supports efficient inspection procedures, integrating into both bench routines and portable check sets. The rigid cross‑section provides the necessary stiffness for repeatable placement, aiding rapid throughput without sacrificing measurement certainty. Stiffness and geometry that support repeatability Cross‑section geometry has been selected to balance rigidity and ease of handling; this lowers the influence of handling variability during verification tasks. Consistent contact faces and tight manufacturing tolerances contribute directly to reproducible results, so inspection records reflect process realities rather than tool drift. The gauge therefore functions as a compact, reliable reference in quality assurance chains. Contact Metav Werkzeuge for procurement advice and to obtain the original Metav IndustryLine end gauge with full specification details and supply options Technical Data Article number: M319.0122.1 GTIN: 4054469130590 Description: End gauge 1.22 mm; DIN EN ISO 3650; Grade 1 Core technical data Nominal size: 1.22 mm Weight: 0.005 kg Tariff number: 90173000 Materials and special features Material: hardened special steel Standard: DIN EN ISO 3650 Grade: 1 Cross‑section: up to 10 mm → 30 x 9 mm; from 10.1 mm → 35 x 9 mm FAQ What tolerance class does this end gauge meet? The end gauge meets Grade 1 tolerance per DIN EN ISO 3650, providing a high level of dimensional accuracy suitable for industrial inspection. Is the gauge suitable for routine workshop inspection? Yes, the Metav IndustryLine end gauge is designed for workshop and laboratory inspection, offering a compact, wear‑resistant reference for pass/fail checks. What material is the gauge made from and how does that help? Made from hardened special steel, the gauge resists wear and preserves contact geometry, which supports stable, repeatable measurement results. Which nominal size is supplied for this item? The supplied nominal size is 1.22 mm (Article number M319.0122.1), intended as a precise reference dimension for verification tasks. How does cross‑section geometry affect use? The specified cross‑section dimensions improve stiffness and handling, reducing deformation risk during measurement and supporting reproducible results. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.22 mm Gauge Block Single End, Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Precision length standard with Grade 0 accuracy and conformity to DIN EN ISO 3650 ensures a stable reference for calibration and inspection. Benefit from the compact, hardened construction and order the single gauge block directly via Metav Werkzeuge or request technical advice from our consultants. Single gauge block 1.22 mm (Grade 0) — Metav IndustryLine, DIN EN ISO 3650 The single gauge block 1.22 mm is a high-precision length reference designed for calibration, inspection and assembly verification in workshops and metrology labs. DIN EN ISO 3650 Grade 0 accuracy Hardened special steel construction Nominal length 1.22 mm precision reference Compact, low-mass traceable standard Reliable reference for calibration routines The Grade 0 tolerance, specified under DIN EN ISO 3650, makes this gauge block an accurate and reproducible length reference. With a nominal size of 1.22 mm, the component serves as a stable standard for comparison checks, incoming inspection and instrument cross‑verification. The hardened construction minimises dimensional drift, supporting consistent measurement results and reducing uncertainty in routine calibration tasks. Practical handling for workshop and laboratory use The compact format and low mass simplify handling and short measurement cycles. The block's cross-section for nominal lengths up to 10 mm is 30 × 9 mm, which provides a rigid profile for easy seating and manipulation on flat reference surfaces. Weighing just 0.005 kg, the item integrates cleanly into existing gauge sets and bench workflows, enabling rapid reference checks without extensive setup or specialised fixtures. Traceability and specification clarity for quality systems Manufactured to DIN EN ISO 3650 and delivered under the Metav IndustryLine designation, the block supports traceable measurement routines and documentation needs. The clear specification of material: hardened special steel and the visible SKU ensure straightforward identification within inventory and quality records. This stability and conformity aid in maintaining process control, reproducible assembly tolerances and audit-readiness in production environments. For a traceable Grade 0 length standard from Metav IndustryLine, request availability or technical consultation via Metav Werkzeuge GmbH in Emmerich (info@metav-werkzeuge.com / +49 2822 7131930) Technical Data SKU: M319.0122.0 GTIN: 4054469130583 Label: Single gauge block 1.22 mm, DIN EN ISO 3650, Grade 0 Facts Nominal size: 1.22 mm Weight: 0.005 kg Cross-section: 30 × 9 mm (for nominal lengths ≤ 10 mm) Tolerance grade: 0 (DIN EN ISO 3650) Customs tariff number: 90173000 Special features Material: hardened special steel Category: End gauge block Manufacturer brand: Metav IndustryLine Intended use: calibration reference, inspection, assembly verification FAQ What accuracy class does this gauge block hold? The single gauge block 1.22 mm is produced to Grade 0 according to DIN EN ISO 3650, offering a tolerance level suitable for high‑precision workshop and laboratory comparisons. Which material is used for the block? The block is made from hardened special steel, chosen for dimensional stability and wear resistance under normal handling and storage conditions. How should the gauge block be stored and handled? The single gauge block 1.22 mm should be kept clean, dry and protected from knocks; storage in a dedicated protective case and use with clean fingers or tweezers preserves the measuring faces and long‑term accuracy. Is this gauge block suitable for routine workshop calibration? Yes. The Metav IndustryLine gauge block in 1.22 mm is designed as a stable reference for routine calibration, spot checks and instrument cross‑verification within production and inspection areas. What are the exact dimensions and identification details? Nominal length: 1.22 mm; cross-section: 30 × 9 mm; weight: 0.005 kg; SKU: M319.0122.0 Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.22mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
A compact, stable length standard that combines the ceramic material with Grade 1 (DIN 861/1) tolerance to deliver a reliable reference at 1.22 mm nominal size; ideal where thermal stability and wear resistance matter. Order the gauge block directly via Metav Werkzeuge or consult our specialists for application guidance. Ceramic gauge block 1.22 mm, Grade 1 (DIN 861/1) — Metav IndustryLine precision standard A ceramic gauge block 1.22 mm engineered as a high-stability length reference for calibration benches, laboratory use and quality control checks Ceramic construction for thermal stability Grade 1 tolerance per DIN 861/1 Precise nominal size 1.22 mm Stable reference for repeatable measurements The block serves as a proven length standard where repeatability is essential. Made from ceramic, the material offers low thermal expansion and high surface hardness, which reduces dimensional drift during short-term temperature fluctuations and everyday handling. The Grade 1 specification according to DIN 861/1 defines the tolerated deviation band, so the component functions as a trustworthy reference in routine verification and comparison tasks. Designed to reduce uncertainty in quality processes With a nominal size of 1.22 mm, this end standard is intended for fine adjustment and verification of micrometre-scale settings. Its compact form and minimal mass support quick comparisons on a measurement bench and simplify handling during set-up. By using a dedicated ceramic reference, the likelihood of wear-induced error is lowered, contributing to consistent precision across repeated checks and helping to stabilise process capability in production or inspection environments. Practical advantages of ceramic in metrology Ceramic gauges combine dimensional stability with chemical inertness, making them suitable for environments where metal standards might be affected by corrosion or magnetism. The wear resistance of the ceramic surface preserves the reference dimension over time, which reduces the need for frequent replacement and supports long-term traceability when paired with documented calibration routines. This makes the product particularly appropriate for laboratories and workshops seeking low-maintenance, reliable standards. Integration into calibration and inspection workflows The gauge block is a straightforward element within a calibration set or a dedicated control routine. It can be used as a primary comparator for small instruments or as an insertion element in jigs and fixtures for set-up checks. Clear labelling and a compact footprint allow efficient storage and easy retrieval during shift changes, supporting uninterrupted measurement routines and quick decision-making in quality control. For thermally stable, Grade 1 length references from Metav IndustryLine, contact Metav Werkzeuge in Emmerich to discuss the M324.001.22 and ensure the correct standard selection for calibration and inspection tasks Technical data Article number: M324.001.22 GTIN: 4054469142593 Tariff number: 90173000 Material: Ceramic Nominal size: 1.22 mm Grade: 1 (DIN 861/1) Weight: 0.001 kg Core data Nominal dimension: 1.22 mm Tolerance class: Grade 1 Weight (approx.): 0.001 kg Special features Category: End standard / gauge block Label: Keramik-Endmaß 1,22mm, Güte 1 DIN 861/1 Manufacturer brand: Metav IndustryLine FAQ What is the intended use for this ceramic gauge block? The ceramic gauge block is intended as a stable, repeatable length reference for calibration benches, laboratory checks and routine quality control, with the nominal size 1.22 mm serving fine-measurement applications. Does the block meet a recognised tolerance standard? Yes, the block is specified as Grade 1 in accordance with DIN 861/1, which defines the acceptable tolerance band for this class of length standard. What advantages does the ceramic material provide? Ceramic offers low thermal expansion and good wear resistance, making the gauge block suitable where dimensional stability and reduced maintenance are priorities. How should the block be stored to maintain accuracy? Store the gauge block in a clean, temperature-stable environment, free from abrasive contact and strong humidity, to preserve the surface and ensure continued measurement reliability. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.23 mm Gauge Block Grade 1, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of a compact, factory-grade reference that combines DIN EN ISO 3650 conformity with a hardened special-steel construction for durable, repeatable measurements; the precise 1.23 mm nominal size and Grade 1 accuracy make this gauge block ideal for routine calibration and inspection tasks. Order directly via Metav Werkzeuge or consult our specialists for application advice. Gauge block 1.23 mm – Grade 1, DIN EN ISO 3650 (Metav IndustryLine) A Gauge block 1.23 mm designed as a high-precision end standard for reference measurements and calibration in workshops and inspection laboratories. Grade 1 accuracy to DIN EN ISO 3650 Hardened special steel construction Nominal size 1.23 mm for fine calibration Compact, low-mass precision standard Consistent precision that supports reliable quality control The block is manufactured to DIN EN ISO 3650 and supplied as a Grade 1 reference, providing a stable baseline for comparison and calibration routines. As a compact gauge block, it is purpose-made for establishing traceable lengths in inspection setups and for creating calibrated stacks. The conformity to the standard assures compatibility with established metrology procedures and simplifies integration into existing quality workflows. This emphasis on standardisation reduces measurement uncertainty in downstream processes and speeds up decision-making in production control. Robust material and handling benefits for daily use Made from hardened special steel, the end standard resists wear and maintains form under repeated contact, which extends service life and lowers replacement frequency. The low mass (approx. 0.005 kg) and compact dimensions favour easy handling and rapid stacking with other blocks during set-up. The specified cross-section (up to 10 mm: 30 × 9 mm; from 10.1 mm: 35 × 9 mm) provides sufficient face area for stable clamping and temperature equalisation. These material and geometric choices deliver a balance of durability and user-friendly handling in routine inspection tasks. Practical use: how it fits into inspection and calibration workflows The block functions as a primary end standard for creating calibrated stacks, setting up slip gauges, and verifying gauge fixtures. Its 1.23 mm nominal size makes it particularly suitable for fine adjustments, small-gap verification and for use alongside other precision standards in comparative measurements. Stacking allows building larger reference lengths while preserving traceability; the compact format streamlines transport within the workshop and speeds up exchange between measuring stations. The robust finish minimises surface damage during normal use and supports repeatable contact measurement techniques. Why this Metav IndustryLine standard is a pragmatic choice Choosing a standard that combines recognised ISO conformity, hardened construction and a compact profile translates into lower process risk and predictable measurement behaviour. The gauge block is a practical investment for inspection labs and maintenance teams that require dependable references without complex handling procedures. As part of the Metav IndustryLine range, this end standard benefits from the supplier’s European quality filter and logistics base in Emmerich, which supports reliable availability for industry and trade. Secure Metav IndustryLine gauge blocks through Metav Werkzeuge in Emmerich—contact the Metav Werkzeuge team at info@metav-werkzeuge.com or +49 2822 7131930 for purchasing advice and supply details Technical data SKU: M319.0123.1 GTIN: 4054469130613 Norm: DIN EN ISO 3650 Grade: 1 Facts Nominal size: 1.23 mm Weight: 0.005 kg Tariff code: 90173000 Cross-section: up to 10 mm — 30 × 9 mm; from 10.1 mm — 35 × 9 mm Special features Material: special steel, hardened Category: gauge block / end measure Brand: Metav IndustryLine Intended use: reference and calibration standard FAQ What level of accuracy does this block provide? The gauge block is supplied as a Grade 1 end standard manufactured to DIN EN ISO 3650, offering the accuracy and repeatability expected for routine calibration and inspection tasks. Can the block be stacked with other blocks for larger reference lengths? Yes, the block is designed for stacking with other gauge blocks and end standards to build combined reference lengths while preserving traceability and measurement stability. What material is used and how does it affect longevity? The block is made from hardened special steel, which improves wear resistance and ensures a durable contact surface for frequent use. Is this item suitable for laboratory reference and shop-floor inspection? The compact format and DIN EN ISO 3650 conformity make the block suitable for both laboratory and workshop calibration duties, offering a practical compromise between precision and handling. What is the exact product identifier for ordering? Order using SKU M319.0123.1; this identifies the Gauge block 1.23 mm from the Metav IndustryLine range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.23 mm Gauge Block Single End, Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
High-precision reference dimensions from a hardened special-steel gauge block with DIN EN ISO 3650 compliance and tolerance grade 0 provide reproducible calibration points; the nominal size of 1.23 mm makes this single block ideal for assembling precise gauge sets or verifying micrometre and caliper lines. Order directly via Metav Werkzeuge or consult our specialists for tailored quantities and delivery. Single gauge block 1.23 mm — DIN EN ISO 3650, grade 0 (Metav IndustryLine) Single gauge block 1.23 mm for traceable dimensional referencing in inspection benches and calibration laboratories DIN EN ISO 3650, tolerance grade 0 Hardened special steel construction Nominal size 1.23 mm for calibration tasks Reproducible accuracy for calibration and inspection A compact reference element engineered to the DIN EN ISO 3650 standard, this single gauge block delivers the dimensional reliability required in calibration and quality assurance workflows. The block’s grade 0 tolerance ensures tight conformity to nominal dimensions, reducing uncertainty when comparing measuring instruments or building a set of reference standards. Designed as a reference rather than a measuring instrument, this component supports consistent results across repeated comparative checks and helps maintain traceability chains within laboratory environments. Durable construction that retains reference over time Manufactured from hardened special steel, the block resists wear and maintains flatness and parallelism under normal handling, which preserves its role as a stable datum. The choice of material reduces the need for frequent refurbishment and limits measurement drift, so reference assemblies and comparator setups remain dependable. The small mass and compact geometry also make handling straightforward during assembly of gauge stacks, while the specified cross-section dimensions contribute to mechanical stability in stacking and clamping situations. Practical integration into workshop and laboratory routines Supplied as a single reference length, the unit integrates easily into existing gauge block sets or serves as a targeted reference for setting up micrometres, calipers and comparator jaws. Clear conformity to the DIN EN ISO 3650 standard simplifies documentation and quality records, aiding acceptance during internal audits or supplier assessments. Where tight tolerances are essential, this block functions as a quick, traceable check to confirm instrument behaviour before critical measurements are taken. For traceable precision from Metav IndustryLine, contact Metav Werkzeuge for ordering or technical consultation at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss batch sizes and lead times Technical data Article number: M319.0123.0 GTIN: 4054469130606 Description: Single gauge block 1.23 mm, DIN EN ISO 3650, grade 0 Manufacturer: Metav IndustryLine Label: Einzel-Endmaß 1,23 mm, DIN ISO 3650, Güte 0 DIN ISO 3650 Facts Nominal size: 1.23 mm Weight: 0.005 kg Cross-section: up to 10 mm → 30 x 9 mm; from 10.1 mm → 35 x 9 mm Tolerance grade: 0 Customs tariff number: 90173000 Special features Material: Special hardened steel Standard: DIN EN ISO 3650 Category: Gauge blocks (Endmasse) Suitable as reference element for gauge sets FAQ What does tolerance grade 0 mean for a gauge block? Tolerance grade 0 indicates a very tight dimensional tolerance under DIN EN ISO 3650; the single gauge block 1.23 mm meets these limits and is suitable where high reproducibility of the reference dimension is required. Is this gauge block suitable for use as a calibration reference? Yes. The block is designed as a reference element and, when used within a controlled process, supports calibration and comparative checks of measuring instruments and gauge stacks. Which material is used and how does this affect wear? The block is made from hardened special steel, chosen for its wear resistance and dimensional stability, which helps to maintain the reference dimension through regular use. Can the block be stacked with other gauge blocks? The geometry and cross-section dimensions are compatible with standard gauge-block stacking procedures, allowing integration into sets for compound lengths and reference assemblies. How should the block be stored to preserve accuracy? Store the block in a clean, dry environment and avoid abrasive contact; typical practice is to keep gauge blocks in a protective case or drawer to prevent nicks and contamination. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.23mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of Grade 1 accuracy and the inherent wear resistance of ceramic to secure a compact reference standard for fine inspection tasks; order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Keramic End Gauge 1.23 mm — Ceramic end gauge, Grade 1 (DIN 861/1) The Keramic End Gauge 1.23 mm is a compact ceramic reference for high-precision inspection and calibration work, suitable for toolrooms and laboratory environments where a stable, hard-wearing master is required Grade 1 accuracy (DIN 861/1) High wear resistance ceramic material Compact reference for calibrations and inspections Consistent reference performance for quality control This compact ceramic end gauge provides a stable reference standard thanks to the combination of Grade 1 tolerance and the intrinsic properties of ceramic. The nominal size of 1.23 mm ensures reliable dimensional comparison where a small master is required. For manufacturers and inspection departments this means fewer reworks and a clearer acceptance decision when checking micro-components. Durable material that reduces maintenance cycles Made from high‑hardness ceramic, the gauge resists abrasion and maintains dimensional stability under normal workshop handling. The material choice reduces the frequency of surface rework compared with softer masters, which in turn lowers downtimes for recalibration or replacement. The low mass and compact footprint also simplify handling during routine checks. Integrates into traceable measurement routines The product functions as a stable datum for calibration benches and incoming inspection. When used as part of a documented control plan, the ceramic end gauge supports consistent pass/fail decisions and enables clear traceability in measurement records. Its small size makes it particularly suitable for verification of micrometres, small fixtures and precision instruments. For reliable master measurements and application guidance contact Metav Werkzeuge in Emmerich — Metav Werkzeuge can advise on integrating this Grade 1 ceramic end gauge into existing QA processes and discuss calibration options; eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical Data Article number: M324.001.23 GTIN: 4054469142609 Tariff number: 90173000 Facts Nominal size: 1.23 mm Weight: 0.001 kg Grade: 1 (DIN 861/1) Special features Material: ceramic Category: End gauges Compact form factor for micro‑inspection tasks FAQ What tolerance class does this end gauge meet? The Keramic End Gauge 1.23 mm is manufactured to Grade 1 in accordance with DIN 861/1, providing a stable reference for fine measurements. Is the gauge suitable for use in a calibration laboratory? Yes, the ceramic composition and Grade 1 accuracy make this gauge appropriate as a reference master within calibration and inspection routines. How does ceramic compare with steel masters for wear? Ceramic gauges generally offer superior wear resistance and dimensional stability under standard inspection conditions compared with many steel masters, extending service intervals. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.24 mm End Gauge Grade 1 DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of precise nominal sizing, hardened special steel construction and conformity to DIN EN ISO 3650 for reliable, repeatable plug checks. The nominal diameter of 1.24 mm in Grade 1 quality combines compact handling with high wear resistance for routine inspection tasks. Order the End gauge 1.24 mm directly via Metav Werkzeuge or ask our consultants if needed. End gauge 1.24 mm — DIN EN ISO 3650 Grade 1 (Metav IndustryLine) The End gauge 1.24 mm is a precision nominal plug for verification of small bore diameters in machining and quality control environments Grade 1 accuracy to DIN EN ISO 3650 Hardened special steel construction Compact cross-section for stable handling Precision where it counts for small-bore inspection The End gauge 1.24 mm is produced to DIN EN ISO 3650 and supplied in Grade 1, which defines the tolerances and intended use for nominal plug gauges. With a 1.24 mm nominal size this master element is ideal for verifying tight bores and for spot-checks on production runs. The adherence to a recognised international standard supports traceable inspection routines and makes the gauge suitable for shop-floor quality checks and laboratory comparisons alike. By specifying a defined tolerance class, the gauge provides a reliable pass/no‑pass reference that reduces uncertainty during acceptance tests. Built for repeatable inspection and long service life Manufactured from hardened special steel, the plug offers a hardened surface that resists wear under repeated use, maintaining dimensional stability over time. The compact 30 x 9 mm cross‑section (applicable for nominal sizes up to 10 mm) improves grip and reduces the tendency to tilt during manual insertion, supporting consistent seating and repeatability in measurements. The lightweight construction minimises handling fatigue while the robust finish ensures the calibrated form remains intact through daily use, contributing to lower replacement and downtime costs. How it enhances workflow and quality assurance As a certified nominal element, this plug gauge simplifies routine inspection steps: quick verification of bores, setting reference limits on gauges and gaging fixtures, and fast acceptance checks at the production station. Using a standardised master reduces the risk of false rejects and rework by providing an unequivocal reference for pass/no‑pass decisions. The compact size eases storage and integration into existing inspection kits, while the clear specification promotes interoperability with established inspection procedures and documentation, improving throughput without compromising accuracy. Contact Metav Werkzeuge in Emmerich for tailored procurement advice on Metav IndustryLine end gauges and to ensure the right selection for your inspection workflow Technical Data Article number: M319.0124.1 GTIN: 4054469130637 Nominal size: 1.24 mm Material: Special steel, hardened Standard: DIN EN ISO 3650 Grade: 1 Weight: 0.005 kg Tariff code: 90173000 Cross-section: 30 x 9 mm (for nominal sizes ≤ 10 mm) Facts Nominal size: 1.24 mm Weight: 0.005 kg Cross-section: 30 x 9 mm Grade: 1 GTIN: 4054469130637 Tariff number: 90173000 Special features Hardened special steel DIN EN ISO 3650 conformity Compact profile for stable handling Category: End gauges SKU: M319.0124.1 FAQ What tolerance class does this gauge meet? The End gauge 1.24 mm is manufactured to DIN EN ISO 3650 and supplied in Grade 1, providing defined tolerances for routine pass/no‑pass checks. Which material is used for the gauge? The gauge is made from hardened special steel, chosen for its wear resistance and dimensional stability under frequent use. How is this type of gauge typically used in the workshop? This plug is used as a nominal reference for verification of small bore diameters, for fixture setting and for quick acceptance checks during production. What cross-section and handling benefits does the gauge offer? The compact 30 x 9 mm cross-section (for nominal sizes up to 10 mm) improves grip stability and helps ensure consistent seating during manual inspections. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.24 mm Gauge Block Single End, Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of the combination of Grade 0 accuracy, hardened special steel and a compact cross-section for reliable reference measurements in workshop and inspection settings; order this precision gauge directly via Metav Werkzeuge or consult our specialists for application advice. Gauge block 1.24 mm — Grade 0 reference gauge (DIN EN ISO 3650) The gauge block 1.24 mm is a single precision reference used for traceable length comparison and stacking in inspection, calibration and toolroom environments. Hardened special steel construction Grade 0 accuracy to DIN EN ISO 3650 Nominal length 1.24 mm Compact cross-section 30x9 mm Precision that secures process quality This compact reference element delivers Grade 0 reproducibility as defined in DIN EN ISO 3650, which means the block provides a standard of accuracy suited for calibration tasks and high‑precision checks. A gauge block at 1.24 mm nominal length serves as a fine incremental element in a stack or as an individual reference when verifying micrometres, comparators and calibrated fixtures. The standardised tolerance class reduces rework and inspection uncertainty, supporting faster decision‑making on the shop floor and in the quality laboratory. Durability for repeated reference use Manufactured from hardened special steel, the block maintains flatness and wear resistance under frequent wringing and handling. The compact 30x9 mm cross‑section (applicable for nominal lengths below 10 mm) combines stiffness with easy handling, making this single element practical for daily stack configuration without unnecessary bulk. The small mass and robust finish reduce the risk of handling damage and help preserve the reference surface quality over many cycles. Easy integration into calibration routines As an individual precision element, this block fits seamlessly into existing reference stacks and inspection jigs, simplifying incremental calibration procedures and comparative checks. The small size and established DIN EN ISO 3650 grading ensure compatibility with common metrology practices and gauge sets. For specific application questions or stacking recommendations, Metav Werkzeuge can advise on best practice and complementary reference measures to build a consistent, auditable measurement chain using this gauge block, SKU M319.0124.0. Choose the Metav IndustryLine gauge block for Grade 0 accuracy and long‑term reliability — contact Metav Werkzeuge for tailored advice on integrating this reference into your quality workflow. Technical data Article number: M319.0124.0 GTIN: 4054469130620 Tariff number: 90173000 Facts Nominal length: 1.24 mm Weight: 0.005 kg Cross-section (applicable): 30 x 9 mm Accuracy grade: 0 Standard: DIN EN ISO 3650 Special features Material: Special steel, hardened Category: Gauge block / end measure Intended use: Reference and comparison measurements FAQ What tolerance class does this gauge block have? The gauge block is specified in grade 0 according to DIN EN ISO 3650, which designates its permissible dimensional deviation and suitability as a precision reference. What material is used for the block and why does it matter? This single gauge is made from hardened special steel, chosen for its stability and wear resistance; the material helps maintain flatness and measurement fidelity during repeated wringing and use. Is the gauge block suitable for stacking with other reference elements? Yes, the block is designed for use in stacks and comparison sets; its 1.24 mm nominal length and standardised grade ensure compatibility with common metrology practices. Which applications are typical for this reference element? The block is intended for precision checks in inspection, calibration and toolroom contexts — ideal for verifying micrometres, setting up comparators and forming part of a traceable reference chain. What is the exact designation and SKU for ordering? The product is offered as Gauge block 1.24 mm, Grade 0 (DIN EN ISO 3650), SKU M319.0124.0, from the Metav IndustryLine range. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.24mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Benefit from the combination of ceramic construction, Grade 1 accuracy to DIN 861/1 and a compact 1.24 mm nominal size for a stable, wear‑resistant reference in length measurement. Order the gauge block directly via Metav Werkzeuge or consult our specialists for application advice. M324.001.24 Ceramic Gauge Block, 1.24 mm — Grade 1 (DIN 861/1) by Metav IndustryLine The M324.001.24 ceramic gauge block is a compact reference standard designed for high‑precision length calibration and inspection, suitable for metrology laboratories and quality control environments Grade 1 accuracy to DIN 861/1 Wear‑resistant ceramic material Compact 1.24 mm nominal size Consistent accuracy for repeatable measurements The combination of Grade 1 classification and conformity to DIN 861/1 ensures a reliable baseline for comparative length checks and instrument verification. This level of conformity communicates a clear technical expectation: measurements conducted against this reference are reproducible within the tolerance band defined for Grade 1. For organisations that prioritise measurable improvement in process control, the block functions as a concise, traceable standard that supports decision‑making in inspection and assembly workflows. Material benefits that support longevity and stability Constructed from ceramic, the gauge block delivers high surface hardness and good resistance to wear, reducing the need for frequent replacement in daily use. The material choice also minimises chemical reactivity compared with untreated metals, which helps preserve the block’s functional surface over many cycles of contact. These attributes translate directly into lower lifecycle disturbance and predictable behaviour during comparative gauging, which is particularly advantageous where small form factors are required for exacting fits and micro‑components. Integration into calibration and inspection routines At 1.24 mm nominal size the block fills a specialised niche within a set of reference standards, enabling precise small‑gap and thin‑part inspections without resorting to compound shimming. Its lightweight construction eases handling and rapid positioning during routine checks. When combined with a structured calibration regime and documented measurement methods, the block supports efficient throughput in quality control: fewer interruptions for rework, clearer pass/fail decisions and consistent traceability for audit purposes. For application guidance or to secure supply of the Metav IndustryLine ceramic gauge block, contact Metav Werkzeuge in Emmerich for technical advice and reliable delivery options Technical data SKU: M324.001.24 GTIN: 4054469142616 Tariff number: 90173000 Manufacturer: Metav IndustryLine Facts Nominal size: 1.24 mm Weight: 0.001 kg Grade: 1 Special features Material: Ceramic Standard: DIN 861/1 Category: Gauge blocks FAQ What accuracy can be expected from this gauge block? The M324.001.24 ceramic gauge block is specified as Grade 1 to DIN 861/1, providing the precision expected of that grade for comparative metrology tasks. Is ceramic suitable for everyday workshop use? Yes; the ceramic construction of the M324.001.24 offers high surface hardness and wear resistance, making it appropriate for repeated comparative measurements in laboratory and production inspection areas. Can this block serve as a reference in a calibration set? The M324.001.24 is intended as a reference length standard and can be integrated into calibration sequences where a compact 1.24 mm nominal gauge is required. How should the gauge block be stored when not in use? Store the M324.001.24 in a stable, dry environment separate from abrasive media; use protective packaging to avoid contact damage and maintain the reference surface condition. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.25 mm Gage Block Grade 1, Hardened Special Steel, DIN EN ISO 3650 - Metav IndustryLine
Take advantage of Grade 1 accuracy and DIN EN ISO 3650 conformity combined with a hardened special steel construction for a compact, traceable reference in precision measurement; order the gauge block directly via Metav Werkzeuge or contact our consultants for application advice. End gauge 1.25 mm (DIN EN ISO 3650), Grade 1 — Hardened special steel precision gauge block The End gauge 1.25 mm (DIN EN ISO 3650), Grade 1 is a compact precision gauge block designed as a traceable reference for calibration tasks and dimensional verification in metrology and quality‑control environments. Grade 1 accuracy to DIN EN ISO 3650 Hardened special steel construction Precision nominal size 1.25 mm Reliable reference for repeatable measurements A compact reference standard such as this offers stable contact geometry and minimal thermal response, ensuring repeatable measurement points in routine checks. Manufactured to DIN EN ISO 3650 and produced in hardened special steel, the block provides a stable datum for comparative gauging and master‑setting tasks. Its Grade 1 classification records conformity to industry tolerances, which simplifies acceptance during internal audits and when establishing measurement chains. Robust design for handling and longevity The hardened substrate and defined cross‑section produce a resilient working surface that resists wear during regular use, reducing the need for early replacement. The modest mass and compact dimensions facilitate easy handling and integration into inspection workflows, while the clearly specified cross‑section for sub‑10 mm sizes (30 x 9 mm) supports secure clamping and seating in small fixtures. As a result, the gauge block sustains metrology routines without compromising on stability. Practical integration into quality systems This precision piece functions as a portable calibration artefact and a reference in workshop and laboratory settings, where traceability and conformity matter. The nominal dimension of 1.25 mm is suited for fine step checks and as part of a set of gauge blocks for building compound lengths. Technical staff benefit from straightforward implementation: the block can be used for direct comparison checks, reference setting on micrometers or callipers, and as a baseline for short‑range dimensional verification workflows. Choose Metav IndustryLine’s Grade 1 gauge block for a compact, traceable reference—contact Metav Werkzeuge in Emmerich for tailored advice and secure supply. Technical data Article number: M319.0125.1 GTIN: 4054469130651 Standard: DIN EN ISO 3650 Nominal size: 1.25 mm Weight: 0.005 kg Tariff code: 90173000 Material: Hardened special steel Quality grade: 1 Cross-section: up to 10 mm → 30 x 9 mm Category: End gauges FAQ What tolerance class does this gauge meet? The gauge meets Grade 1 tolerances according to DIN EN ISO 3650, providing an industry‑recognised accuracy class for reference measurements. Is the nominal dimension 1.25 mm suitable for small‑part inspection? Yes, the 1.25 mm nominal size is ideal as a short reference for fine dimensional checks and for composing precise compound lengths with other gauge blocks. What material is used and why does it matter? The block is made from hardened special steel, chosen for surface hardness and wear resistance so that the reference surface remains stable under regular use. Can this gauge be used for setting micrometers and callipers? Yes, this gauge block serves as a stable reference for setting and verifying short‑range measuring instruments such as micrometers and precision callipers. What is the article number and where can it be sourced? The article number is M319.0125.1 and it is supplied through Metav IndustryLine channels. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.25 mm Gauge Block, Hardened Special Steel, DIN EN ISO 3650 Grade 0 - Metav IndustryLine
Take advantage of DIN EN ISO 3650 conformity and Grade 0 accuracy combined with a hardened special steel body for reliable, repeatable reference measurements; order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Single gauge block 1.25 mm — Grade 0, DIN EN ISO 3650 (Metav IndustryLine) Single gauge block 1.25 mm for high-precision length standards and laboratory or workshop calibration tasks Grade 0 accuracy to DIN EN ISO 3650 Hardened special steel construction Compact 1.25 mm nominal size Manufacturer SKU M319.0125.0 Accuracy that supports quality systems and inspection routines The gauge block is manufactured to DIN EN ISO 3650 and carries Grade 0 accuracy, making it suitable as a reference element in inspection benches and calibration chains. With a nominal size of 1.25 mm, this single block enables the construction of master lengths or verification standards when combined with other blocks. The standard-based tolerance class ensures compatibility with established measurement protocols in production control and metrology labs, supporting traceable and reproducible results in routine checks and sample inspections. Robust material and compact design for enduring use Made from hardened special steel, the block resists wear and keeps measurement faces stable over repeated wringing and handling cycles. Its compact cross-section of 30 x 9 mm (applicable for nominal sizes up to 10 mm) provides a comfortable grip while limiting thermal mass, which helps to reduce short-term thermal drift during short measurement tasks. The low mass (approx. 0.005 kg) makes the piece easy to handle and integrate into sets; the hardened surface preserves accuracy and extends service life under normal workshop conditions. Practical application and integration into workshop workflows The single block is supplied as an individual reference piece suitable for building bespoke sets or replacing individual elements in existing collections. Identified as M319.0125.0 and GTIN 4054469130644, it integrates straightforwardly into inventory and quality documentation. As a Grade 0 end gauge, it is ideal where high conformity and interchangeability matter — for example, in final inspection, gauge calibration, or as a reference for setting micrometres and length-measuring instruments. Careful storage and handling will maintain performance and ensure long‑term repeatability. Contact Metav Werkzeuge for delivery options, application guidance and precise logistics from Emmerich — Metav IndustryLine specialists are available by email or phone to advise on integrating this reference into existing calibration routines Technical data Article number: M319.0125.0 GTIN: 4054469130644 Material: Special steel, hardened Standard: DIN EN ISO 3650 Facts Nominal size: 1.25 mm Weight: 0.005 kg Cross-section: 30 x 9 mm Tariff number: 90173000 Special features Accuracy grade: 0 Category: End gauges Manufacturer designation: Metav IndustryLine FAQ What accuracy class does this gauge block meet? The single gauge block meets Grade 0 accuracy according to DIN EN ISO 3650, providing a reference level appropriate for laboratory and high‑precision workshop use. Is the block suitable for building a precision set? Yes, the Single gauge block 1.25 mm (M319.0125.0) is designed for combination with other blocks to form master lengths and can be used to supplement existing sets. What material is used and how does it affect durability? The block is made from hardened special steel, which increases wear resistance of the measuring faces and supports long-term repeatability when handled and stored correctly. How is the item identified for inventory and traceability? Identification is by manufacturer SKU M319.0125.0 and GTIN 4054469130644, enabling straightforward entry in quality records and stock systems. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.25mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
The combination of ceramic construction, Grade 1 conformity (DIN 861/1) and a compact 1.25 mm nominal length provides a stable, wear‑resistant reference for fine calibration tasks; order the gauge block directly via Metav Werkzeuge or contact our consultants for application advice. Ceramic gauge block 1.25 mm, Grade 1 (DIN 861/1) — Metav IndustryLine A Ceramic gauge block 1.25 mm, Grade 1 (DIN 861/1) intended as a compact length standard for precision calibration and workshop measurement tasks. Ceramic for thermal stability Grade 1 accuracy per DIN 861/1 Nominal length 1.25 mm for fine calibration Reliable accuracy for calibration and inspection The gauge block is manufactured to Grade 1 in accordance with DIN 861/1, making it a trustworthy short‑range length standard for routine inspection and adjustment work. This conformity means the component can be used as a reference when verifying micrometres, comparators and small‑format measurement setups. The short nominal length of 1.25 mm suits fine adjustment tasks and reduces handling uncertainty, helping to maintain consistent measurement chains in both workshop and laboratory environments. Ceramic construction delivers stability and longevity Made from ceramic, the block benefits from inherently low thermal expansion and high surface hardness compared with many metallic alternatives. These material properties translate into thermal stability during short measurement cycles and excellent resistance to surface wear, which prolongs the reference life and reduces the need for frequent reconditioning. The lightweight format also simplifies handling and integration on precise fixtures where minimal mass is advantageous. Practical use and integration into measurement routines As a compact reference element, the block is useful for setting reference points, checking machine zero‑points and supporting comparative measurements on small parts. Its geometry and material suit repeated positioning on flat reference surfaces and measurement benches. For traceable workflows, the item can be combined with larger reference sets to create a scalable calibration kit that covers a wide spectrum of nominal lengths while keeping the short‑range checks highly reproducible. Proven supply chain and application support The product is supplied under the Metav IndustryLine label, backed by a European quality filter headquartered in Emmerich. This supply and quality control approach supports reliable availability and helps purchasing teams reduce supplier risk. For customers seeking documentation, integration tips or clarification about suitability for particular measuring instruments, Metav’s technical team can provide the necessary guidance to align the reference block with established measurement procedures. Request tailored technical advice or a specification confirmation from Metav Werkzeuge to ensure the Metav IndustryLine ceramic gauge block meets specific calibration needs Technical Data SKU: M324.001.25 GTIN: 4054469142623 Manufacturer: Metav IndustryLine Facts Nominal length: 1.25 mm Weight: 0.002 kg Grade: 1 Customs tariff number: 90173000 Special features Material: Ceramic Standard: DIN 861/1 Category: Endmasse eClass: 21170108 FAQ What tolerance class does this gauge block meet? The gauge block meets Grade 1 tolerances in accordance with DIN 861/1, making it suitable as a short‑range reference for calibration tasks. Can the ceramic block be used in routine workshop checks? Yes, the ceramic construction and compact 1.25 mm nominal length make the block appropriate for routine workshop checks and fine adjustments where a stable short reference is required. Is this block part of a larger reference set? The item can be combined with other length standards to form a reference set; Metav IndustryLine supplies individual blocks and coordinated sets for scalable calibration chains. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.26 mm Gauge Block Grade 0, DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of a certified reference standard with Grade 0 accuracy and conformity to DIN EN ISO 3650 for reliably reproducible measurements; the 1.26 mm nominal size and hardened special steel construction ensure stable reference points with minimal wear. Order this single gauge block directly via Metav Werkzeuge or contact our consultants for application advice and delivery options. Gauge block 1.26 mm (Grade 0) — Metav IndustryLine, DIN EN ISO 3650 The Gauge block 1.26 mm (Grade 0) is a single end measure for precise calibration tasks and metrological reference use in workshop and laboratory environments compliant with DIN EN ISO 3650. Grade 0 accuracy (DIN EN ISO 3650) Hardened special steel construction Nominal size 1.26 mm for fine calibration Compact, low-mass reference standard Deliver consistent measurement results with a certified reference A certified Grade 0 reference reduces uncertainty in calibration routines and provides a stable benchmark for comparative checks. Conformity to DIN EN ISO 3650 means the block meets recognised tolerances for length standards, allowing reliable use with comparators, micrometres and gauge block wringing procedures. The 1.26 mm nominal size is particularly suited to fine-setting tasks and insert checks where small, reproducible lengths are required; using a recognised standard lowers the risk of assembly deviations and rework, improving process efficiency. Robust material and handling for long service life Manufactured from hardened special steel, the single gauge block resists surface wear under normal wringing and storage conditions, preserving dimensional integrity over repeated use. The compact mass and profile make it straightforward to handle in routine calibration workflows while limiting thermal inertia during short handling periods. Appropriate cleaning, controlled handling and storage in a dry environment maintain surface quality; periodic comparison against a higher-level standard preserves traceability and ensures continued measurement reliability. Practical integration into the calibration workflow As a single end measure, this gauge block functions as a precise reference for setting micrometres, verifying thickness gauges, and cross-checking small-length features on production components. Its small footprint simplifies storage in organised inspection kits and reduces the space required in gauging benches. When used as part of a calibration programme, the block supports quicker setup times and clearer pass/fail decisions, contributing directly to higher throughput in quality control while maintaining metrological rigour. Contact Metav Werkzeuge for tailored advice on how the Grade 0 1.26 mm gauge block fits into existing calibration procedures and to request delivery or certification details. Technical data Article number: M319.0126.0 GTIN: 4054469130668 Nominal size: 1.26 mm Standard: DIN EN ISO 3650 Grade: 0 Weight: 0.005 kg Facts Material: Special steel, hardened Cross-section: up to 10 mm: 30 x 9 mm; from 10.1 mm: 35 x 9 mm Customs tariff number: 90173000 Special features Single end gauge block Compliant with DIN EN ISO 3650 Low mass for easy handling FAQ What accuracy class does this gauge block have? The gauge block supplied is a Grade 0 reference, specified under DIN EN ISO 3650, providing tight manufacturing tolerances suitable for high-precision checks. Which material is used for the block and why does it matter? This block is made from hardened special steel, which provides wear resistance and dimensional stability for repeated wringing and calibration use. How is the 1.26 mm gauge block typically used in a workshop? The 1.26 mm block serves as a small-length reference for setting and verifying micrometres, comparator gauges and small assembly fixtures, helping to standardise measurement procedures. Is the block suitable for portable inspection kits? Yes, the compact size and low mass make the block convenient for inclusion in inspection kits and for use at gauging benches without occupying significant space. Can this single gauge block be combined with others for different lengths? Individual blocks such as this 1.26 mm end measure can be wrung together with compatible blocks to create composite lengths for broader calibration tasks. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.26 mm Gauge Block Grade 1 DIN EN ISO 3650, Hardened Special Steel - Metav IndustryLine
Take advantage of Grade 1 accuracy and the conformity to DIN EN ISO 3650 for reproducible dimensional checks; the hardened special steel construction and compact mass ensure safe handling and long service life. Order the gauge directly via Metav Werkzeuge or request advice from its consultants for procurement and quality‑assurance planning. End gauge 1.26 mm — Grade 1 precision (DIN EN ISO 3650) by Metav IndustryLine The End gauge 1.26 mm is a precision reference gauge designed for dimensional inspection and quality control tasks where a certified nominal size and clear traceability are required. Grade 1 accuracy to DIN EN ISO 3650 Hardened special steel construction Compact mass: 0.005 kg GTIN: 4054469130675 Minimise measurement uncertainty with standardised reference accuracy As a Grade 1 reference, this gauge complies with DIN EN ISO 3650, providing a recognised baseline for comparative checks and verification tasks. The nominal size of 1.26 mm is produced to tight form and size tolerances associated with Grade 1 work, which reduces uncertainty when comparing measuring instruments or validating production runs. Using a standardised reference simplifies calibration chains and supports repeatable decision rules in quality control. Durable design for repeatable handling and inspection routines Constructed from hardened special steel, the gauge combines wear resistance with dimensional stability; the compact mass of 0.005 kg aids careful handling and lowers the risk of accidental damage during routine use. For nominal sizes up to 10 mm the cross‑section is 30 x 9 mm, ensuring sufficient stiffness for repeatable contact in bench and fixture applications. The robust material and consistent geometry support long service life and predictable measurement behaviour in workshop and inspection environments. Traceability and procurement clarity for quality systems Traceability is supported by the onboard identifiers: GTIN 4054469130675 and the internal article number M319.0126.1, which facilitate inventory control and documentation in quality management systems. Supplied as an item within the end gauge category, this reference gauge helps standardise inspection procedures across shifts and sites, simplifying supplier qualification and internal audits. Procurement via Metav Werkzeuge leverages an established European supply chain and central stock management for reliable availability. For certified Grade 1 end gauges and procurement guidance from Metav Werkzeuge in Emmerich, contact the Metav Werkzeuge team to discuss ordering quantities and delivery options. Technical data Article number: M319.0126.1 GTIN: 4054469130675 Nominal size: 1.26 mm Standard: DIN EN ISO 3650 Grade: 1 Facts Weight: 0.005 kg Cross-section: up to 10 mm: 30 x 9 mm; from 10.1 mm: 35 x 9 mm Customs tariff number: 90173000 Materials / Features Material: hardened special steel Category: end gauges Label: End gauge 1.26 mm, DIN ISO 3650, Grade 1 FAQ What does Grade 1 mean for this end gauge? Grade 1 indicates compliance with the tolerancing and form requirements of DIN EN ISO 3650, making the gauge suitable as a high‑precision reference in standard inspection tasks. What is the gauge made from? The End gauge 1.26 mm is manufactured from hardened special steel, chosen for wear resistance and long‑term dimensional stability. How can this item be identified for stock and documentation? Identification is possible via GTIN 4054469130675 and article number M319.0126.1, which support traceability within quality documentation and procurement records. What is the cross‑section for this nominal size? For nominal sizes up to 10 mm the cross‑section is 30 x 9 mm, offering stiffness appropriate for repeatable inspection contact. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.26mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Take advantage of the ceramic construction and Grade 1 (DIN 861/1) tolerance to secure a stable reference for fine inspection tasks; the compact 1.26 mm nominal size and ultra‑low mass suit delicate assemblies and minimised thermal influence. Order the gauge directly via Metav Werkzeuge or consult our specialists for application advice. Ceramic End Gauge 1.26 mm, Grade 1 (DIN 861/1) — Metav IndustryLine The Ceramic End Gauge 1.26 mm, Grade 1 (DIN 861/1) is a precision reference element for laboratory and workshop measurement tasks, engineered for repeatable thickness checks and fine calibration work Ceramic measurement shim, high wear resistance Grade 1 tolerance (DIN 861/1) for calibrated accuracy Compact 1.26 mm nominal thickness, ultra-low mass Reliable conformity for quality control The Grade 1 (DIN 861/1) specification ensures the gauge functions as a trustworthy reference in routine inspection and setup tasks. Calibrated reference pieces with a defined tolerance enable clear pass/fail decisions on small thicknesses; the 1.26 mm nominal value provides a precise datum for comparative checks. This element is suited to production monitoring where documented conformity and repeatability reduce rework and inspection time. Material advantages that reduce drift Made from ceramic, the block offers dimensional stability and resistance to surface wear in environments where metallic references can corrode or magnetically interfere. The low mass and material properties lower thermal inertia, helping to keep short‑term measurement drift minimal during repeated contact checks. These characteristics translate into a longer service life for the reference and fewer replacement cycles. Practical handling and traceability in the workshop The compact format and minimal weight simplify handling during fine measurement sequences and make the gauge easy to store in precision drawers. The item is supplied with clear identification (SKU and GTIN) to support inventory and traceability processes in the quality system. For tasks requiring a stable, documented gauge for regular verification routines, this ceramic reference integrates smoothly into inspection benches and calibration sets. For assured traceability and delivery from Emmerich, contact Metav Werkzeuge to request the Metav IndustryLine ceramic end gauge or to discuss calibration and supply options. Technical data Article number: M324.001.26 Material: Ceramic Nominal size: 1.26 mm Grade: 1 (DIN 861/1) Weight: 0.002 kg GTIN: 4054469142630 Tariff number: 90173000 Facts Nominal size: 1.26 mm Weight: 0.002 kg Grade: 1 (DIN 861/1) GTIN: 4054469142630 Tariff number: 90173000 Special features Material: Ceramic Category: End measures / End gauge SKU / Article number: M324.001.26 Brand: Metav IndustryLine Label: Keramik-Endmaß 1,26mm, Güte 1 DIN 861/1 FAQ What tolerance class does the gauge meet? The gauge meets Grade 1 (DIN 861/1), providing a clearly defined tolerance band for precise thickness reference. Is the material suitable for corrosion‑sensitive environments? Yes, the ceramic composition offers excellent resistance to corrosion compared with typical metallic gauges, making it appropriate for corrosive or non‑magnetic measurement applications. Can this item be used as a workshop reference for incoming inspection? The Metav IndustryLine ceramic end gauge serves as a compact reference for incoming inspection where a documented, stable thickness element is required. How is the item identified for traceability? Identification is provided via SKU M324.001.26 and GTIN 4054469142630 to support inventory control and calibration records. What handling precautions are recommended? Handle the gauge with care to avoid chipping; store in a padded drawer or compartment and avoid hard impacts that could alter the reference surface. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.27 mm Gauge Block Grade 1 DIN EN ISO 3650 Hardened Special Steel - Metav IndustryLine
Take advantage of the combination of exacting measurement standard compliance, robust hardened special steel construction and compact nominal size for reliable reference measurements; order the gauge block directly via Metav Werkzeuge or consult our specialists for application advice. Gauge block 1.27 mm — DIN EN ISO 3650 Grade 1, hardened special steel A precision gauge block for laboratory and workshop calibration, suitable as a reliable length reference in inspection and production environments. DIN EN ISO 3650 Grade 1 accuracy Hardened special steel construction Nominal size 1.27 mm reference dimension Precision that supports reproducible inspection results This slip gauge is manufactured to comply with DIN EN ISO 3650, delivering the repeatability required for high-quality calibration work. The 1.27 mm nominal dimension provides a compact reference that is especially useful when verifying micrometre settings, plug gauges or fine fixtures. The combination of standard conformity and a hardened special steel body ensures long-term dimensional stability and resistance to surface wear, helping to reduce uncertainty in routine measurement tasks. The result is a compact, dependable reference for both laboratory and shop‑floor checks. Robust material and geometry for consistent handling Constructed from hardened special steel, the block is designed to retain its gauge surface integrity under frequent use. The small mass and compact cross‑section make it easy to position in tight set‑ups while offering sufficient stiffness for short span references: the listed cross‑section dimensions indicate the manufacturing profile used for blocks below 10 mm. The slender format and low weight simplify handling during stack assembly or single‑piece comparison, and the surface finish supports stable wringing and low friction when assembling stacks. Practical benefits for calibration workflows As a Grade 1 reference, this block supports traceable length setting within inspection routines and tool calibration procedures. Its compact nominal size facilitates quick verification of measurement devices where full‑length standards are impractical. The product’s conformity to recognised standards reduces administrative effort in quality documentation and promotes consistent results across repeated measurements. For workshops aiming to tighten process control, this small reference element provides an efficient way to validate and adjust measuring instruments. Integration into metrology sets and inspection benches The block is suitable for inclusion in a set of gauge blocks or as a standalone reference for specific dimensions. Its compatibility with standard wringing and stacking methods makes it straightforward to combine with other reference elements to achieve a wide range of calibrated lengths. Where space is limited or very small reference values are required, this compact gauge block offers a reliable solution that fits into established inspection workflows without the need for bespoke fixtures. For delivery from stock and technical clarification, contact Metav Werkzeuge in Emmerich for expert advice and reliable supply of precision metrology products Technical data Article number: M319.0127.1 GTIN: 4054469130699 Standard: DIN EN ISO 3650 Grade: 1 Nominal size: 1.27 mm Material: Hardened special steel Net weight: 0.005 kg Tariff number: 90173000 Facts Nominal dimension: 1.27 mm Cross-section up to 10 mm: 30 x 9 mm Cross-section from 10.1 mm: 35 x 9 mm Weight: 0.005 kg Special features Compliance: DIN EN ISO 3650 Grade 1 Construction: hardened special steel Category: Gauge blocks (Endmasse) Intended use: length reference for calibration and inspection FAQ What standard does this gauge block comply with? The gauge block meets DIN EN ISO 3650 requirements and is specified as Grade 1 for high‑precision reference use. What is the material and why does it matter? This block is made of hardened special steel, chosen for wear resistance and dimensional stability under repeated wringing and handling. Is the nominal size suitable for fine calibration tasks? The 1.27 mm nominal dimension is ideal for fine calibration, small stack assemblies and verification of micrometres or fine gauges. Which article number should be referenced when ordering? Please refer to article number M319.0127.1 for ordering and inventory purposes Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.27 mm Gauge Block, Hardened Special Steel, DIN EN ISO 3650 Grade 0 - Metav IndustryLine
Benefit from Grade 0 accuracy and DIN EN ISO 3650 conformity combined with a hardened special-steel construction for a reliable reference standard; the compact dimensions ensure easy handling and reproducible stacks. Order the single gauge block 1.27 mm directly via Metav Werkzeuge or ask our consultants if needed. Single gauge block 1.27 mm — Grade 0, DIN EN ISO 3650 (Metav IndustryLine) A single gauge block 1.27 mm designed as a compact, Grade 0 reference for precision calibration, workshop setting and high‑accuracy inspection tasks. DIN EN ISO 3650 Grade 0 accuracy Hardened special steel construction Compact 30×9 mm cross-section Reliable reference for precision workflows The single gauge block 1.27 mm provides a deterministic reference point for setting and verifying measuring instruments. Conforming to DIN EN ISO 3650 at Grade 0, it offers tight tolerances that reduce uncertainty in gauge stacks and calibration routines. The nominal size of 1.27 mm is ideal for building exact stacks for micrometres, comparators and height gauges, ensuring repeatable setups and minimising machine downtime through faster, accurate adjustment. Durable material and compact handling for daily use Manufactured from hardened special steel, the block resists wear and maintains flatness over repeated wringing and stacking operations. The compact 30×9 mm cross-section (applicable for sizes up to 10 mm) keeps handling comfortable while providing sufficient mass for stable wringing; the listed weight of 0.005 kg reflects a finely finished, easy-to-manage element. The hardened steel surface supports reliable wringing, enabling firm molecular adhesion between blocks and thus stable, low‑error stacks for measurement transfer. Practical applications and measurable benefits As a precision reference, this gauge block is suitable for use in tool rooms, inspection benches and calibration laboratories. Using the block in calibration stacks permits quick verification of micrometres, gauge pins and comparators, improving throughput and measurement confidence. Traceable labelling and a consistent manufacturing standard reduce administrative effort in quality management, while the compact format simplifies storage and transport within a busy workshop environment. For assured reference measurements choose the Metav IndustryLine single gauge block 1.27 mm; contact Metav Werkzeuge in Emmerich for procurement or technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M319.0127.0 GTIN: 4054469130682 Standard: DIN EN ISO 3650 Category: Gauge blocks Facts Nominal size: 1.27 mm Grade: 0 Weight: 0.005 kg Cross-section: 30×9 mm (≤ 10 mm) Tariff number: 90173000 Special features Material: hardened special steel Suitable for calibration stacks and reference measurements Compact format for easy handling Precision finish for reliable wringing FAQ What tolerance class does this gauge block follow? The single gauge block 1.27 mm is manufactured to Grade 0 in accordance with DIN EN ISO 3650, offering tight tolerance limits suitable for workshop and laboratory reference use. Can this block be used in gauge stacks for calibrating micrometres? Yes. The 1.27 mm block (SKU M319.0127.0) is intended for inclusion in calibration stacks to set and verify micrometres, height gauges and comparators, providing a stable reference element. What is the material and how does it affect durability? The block is made from hardened special steel, which provides wear resistance and long-term flatness retention, supporting repeated wringing and stacking without rapid degradation. How should the block be handled and stored to maintain accuracy? Handle the block with clean gloves or a tissue to avoid oils; store in a dry, protected case and avoid impacts. Proper handling preserves the precision finish essential for reliable wringing. Is this gauge block suitable for shop-floor and laboratory environments? Yes. The compact dimensions and DIN EN ISO 3650 Grade 0 specification make it appropriate for both workshop settings and calibration laboratories where a robust, accurate reference is required. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.27mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
The combination of Grade 1 accuracy (DIN 861/1), ceramic wear resistance, and a compact 1.27 mm nominal size delivers a stable reference for fine inspection tasks; order this end gauge directly via Metav Werkzeuge or consult our specialists for tailored specification support. Ceramic end gauge 1.27 mm, Grade 1 DIN 861/1 — Metav IndustryLine reference standard for precise dimensional checks The Ceramic end gauge 1.27 mm, Grade 1 DIN 861/1 is a compact, wear‑resistant reference standard designed for high‑precision inspection and calibration within mechanical workshops and metrology laboratories. Ceramic material for thermal stability and wear resistance Grade 1 accuracy to DIN 861/1 Nominal size 1.27 mm as traceable reference Lightweight 2 g for easy handling in inspection benches Reliable reference for repeatable measurements As a Grade 1 end gauge conforming to DIN 861/1, this small‑format standard provides a robust baseline for comparative measurement tasks. The combination of a precisely manufactured 1.27 mm nominal dimension and the inherent dimensional stability of ceramic makes it suitable as a reference in comparator checks and gauge block cross‑checks. By using a non‑metallic reference with low thermal expansion, measurement variability due to temperature shifts is reduced, supporting reproducible results across short measurement cycles. Low‑maintenance, long‑life inspection standard The use of ceramic gives the gauge a highly wear‑resistant contact face and resistance to typical workshop corrosion mechanisms; this translates into a lower need for frequent reconditioning compared with softer metallic gauges. The very low mass (approx. 2 g) and compact geometry facilitate handling for fine inspection tasks and assembly‑level checks, while preserving surface integrity over extended use. For routine quality control, the gauge functions as a dependable physical limit that retains dimensional fidelity under normal inspection conditions. Practical integration into metrology workflows This end gauge is intended for direct use as a tactile reference in inspection benches, comparator fixtures and manual verification routines. Marked with a unique GTIN and supplied as a single, traceable item, it fits into existing tool inventories and quality documentation systems. When incorporated into regular measurement routines, the gauge supports process stability and simplifies pass/fail decision making by providing an unambiguous physical standard that is quick to position and verify. Contact Metav Werkzeuge in Emmerich for procurement and specification assistance on Metav IndustryLine end gauges and to confirm suitability for specific inspection tasks Technical data Article number: M324.001.27 GTIN: 4054469142647 Tariff number: 90173000 ECLASS: 21170108 Facts Nominal size: 1.27 mm Weight: 0.002 kg Grade: 1 Material: Ceramic Material and special features Ceramic material Category: End gauges / Endmaß Label: Ceramic end gauge 1.27 mm, Grade 1 DIN 861/1 Part of Metav IndustryLine FAQ What level of accuracy does this end gauge provide? The end gauge provides Grade 1 accuracy according to DIN 861/1, offering a reliable reference for fine measurement and comparative checks. Is the material suitable for use near magnetic equipment? Yes, the ceramic composition of the end gauge is non‑magnetic and therefore suitable where magnetic interference must be avoided. How should the gauge be handled and stored to preserve accuracy? Store the gauge in a clean, dry environment and handle it by non‑contact edges where possible; the ceramic surface is wear‑resistant but benefits from careful handling to maintain the Grade 1 condition. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.28 mm Gauge Block Single-End, Hardened Special Steel, DIN EN ISO 3650 Grade 0 - Metav IndustryLine
Take advantage of Grade 0 accuracy and hardened special steel construction to establish a dependable reference in daily metrology work; order directly via Metav Werkzeuge or consult our specialists for specification support. Single gauge block 1.28 mm — precision reference gauge block, DIN EN ISO 3650, Grade 0 (Metav IndustryLine) Single gauge block 1.28 mm serves as a high-precision reference length for calibration and comparative measurement tasks in workshops and inspection rooms, specified to DIN EN ISO 3650 for reliable dimensional standards Grade 0 tolerance for reference measurements Conforms to DIN EN ISO 3650 standard Hardened special steel for long service life Nominal size 1.28 mm for precise calibration Seamless accuracy for routine quality control This reference piece, specified as 1.28 mm nominal, delivers repeatable precision where micro-scale conformity matters. Manufactured to DIN EN ISO 3650 and classified Grade 0, it provides the dimensional stability required for setting and verifying measuring instruments, gauges and comparator systems. The defined tolerance band of a Grade 0 block minimises uncertainty in calibration chains and reduces iteration during inspection, which in turn shortens setup times and supports consistent production throughput. Robust construction that endures daily handling The block is produced from special steel, hardened, and finished with precision grinding to preserve dimensional integrity under frequent use. Its compact cross-section offers convenient handling and secure seating in gauge holders or wringing assemblies; the listed cross-section dimensions ensure compatibility with standard clamp styles. Light in mass yet rigid in form, the component withstands workshop handling without compromising the flatness and parallelism required for reliable wringing and stacking operations, extending service life and lowering replacement frequency. Practical traceability and integration into measurement systems As a single reference element, this block functions either alone or as part of a larger set to build calibrated length chains for inspection benches. Clear identification and an industry-standard specification facilitate documentation in quality records and measurement procedures, supporting internal traceability. When combined with systematic calibration routines, these properties translate into measurable benefits: fewer measurement disputes, faster incoming inspections and a more robust quality-control workflow that scales with production demands. Secure consistent measurement quality with the Metav IndustryLine 1.28 mm gauge block — contact Metav Werkzeuge for procurement and technical advice at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M319.0128.0 GTIN: 4054469130705 Standard: DIN EN ISO 3650 Grade: 0 Facts Nominal size: 1.28 mm Weight: 0.005 kg Cross-section: up to 10 mm — 30 x 9 mm; from 10.1 mm — 35 x 9 mm Special features Material: special steel, hardened Surface: precision ground for wringing Category: gauge block / reference standard Application: dimensional reference for calibration and inspection FAQ What tolerance class does this gauge block meet? The single gauge block meets Grade 0 tolerance according to DIN EN ISO 3650, providing a high-accuracy reference for laboratory and workshop checks. Which material is used for the block and why? The block is made from special steel, hardened, chosen to maintain dimensional stability and surface quality during regular handling and wringing operations. Can this block be used as a standalone reference in inspection routines? Yes, the 1.28 mm element serves as a standalone reference or as part of a length chain for setting comparators and calibrating measuring tools. How should the gauge block be stored to preserve accuracy? Store the block in a clean, dry environment and avoid direct contact with abrasive surfaces; use protective packaging during transport and handling to maintain the ground surfaces. Is this gauge block suitable for building calibrated stacks? The block’s DIN EN ISO 3650 conformity and Grade 0 tolerance make it suitable for stacking with other blocks to assemble required reference lengths. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.28 mm Go Gauge, DIN EN ISO 3650 Grade 1, Hardened Special Steel - Metav IndustryLine
Precise, durable and standards‑compliant: take advantage of the combination of DIN EN ISO 3650 conformity, hardened special steel construction and a compact 1.28 mm nominal size for dependable reference measurements; order directly via Metav Werkzeuge or consult the advisers for application guidance. End measure 1.28 mm – DIN EN ISO 3650, Grade 1 (Metav IndustryLine) The End measure 1.28 mm, DIN EN ISO 3650, Grade 1 is a hardened special‑steel reference gauge designed for laboratory and workshop length verification, offering a compact cross‑section suited to fine comparative measurements and master‑gauge applications DIN EN ISO 3650 Grade 1 accuracy Hardened special steel construction Nominal size 1.28 mm Cross-section 30x9 mm for ≤10 mm Dependable reference accuracy for traceable checks Manufactured to DIN EN ISO 3650 and marked Grade 1, this end measure functions as a precise reference for inspection, gauge setting and comparative measurement tasks. The 1.28 mm nominal size is produced to narrow tolerance bands, ensuring repeatable results when used as a master standard for calipers, comparators or small gaging fixtures. Conformity with the international standard provides a verifiable basis for quality control and supports clear documentation of measurement chains. Robust material and geometry for consistent performance Constructed from hardened special steel, the gauge offers a combination of surface hardness and dimensional stability that reduces wear and maintains datum integrity over repeated use. The specified cross‑section (30x9 mm for sizes up to 10 mm) gives the block a compact, low‑mass geometry that is easy to position while preserving sufficient stiffness for short‑span comparative measurements. The material choice and geometry together minimise deformation risk under normal handling, supporting long‑term reproducibility. Practical use in workshop and metrology environments As a small, precision reference, this gauge is suited to calibration benches and production inspection points where space and handling speed matter. Its compact form and light mass allow quick placement during routine checks, while the standardised grade simplifies acceptance criteria for incoming inspection and in‑process control. The product acts as a reliable comparator when establishing zero points for handheld measuring tools and for verifying micrometre or caliper accuracy against a recognised standard. Contact Metav Werkzeuge today for delivery information and expert advice on integrating the certified end measure into existing inspection routines Technical Data Article number: M319.0128.1 SKU: M319.0128.1 GTIN: 4054469130712 Material: Spezialstahl, gehärtet Standard: DIN EN ISO 3650 Category: End measures Facts Nominal size: 1.28 mm Weight: 0.005 kg Tariff number: 90173000 Special features Tolerance: Grade 1 Cross-section: up to 10 mm: 30x9 mm; from 10.1 mm: 35x9 mm Intended use: reference gauge for inspection and setting Low mass for easy handling FAQ What tolerance class does the end measure meet? The gauge conforms to Grade 1 tolerance as specified in DIN EN ISO 3650, providing a defined accuracy level for reference measurements. What is the nominal dimension of this reference gauge? The nominal size is 1.28 mm, produced and verified to the dimensional requirements of the DIN EN ISO 3650 standard. Which material is used in the construction of the gauge? The body is made from hardened special steel, chosen for durability and dimensional stability under normal workshop conditions. Is this product suitable as a master for caliper checks? Yes, the end measure is designed as a compact reference gauge suitable for comparator and caliper verification tasks where a small, stable datum is required. What are the cross‑section dimensions for handling and clamping? For nominal sizes up to 10 mm the cross‑section is 30x9 mm; for sizes from 10.1 mm the cross‑section is 35x9 mm, offering secure seating and handling geometry. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1.28mm Ceramic Gauge Block Grade 1 DIN 861/1 - Metav IndustryLine
Combine Grade 1 accuracy, ceramic dimensional stability and the compact 1.28 mm nominal size to secure a reliable reference standard for precision length checks; order the ceramic gauge block directly via Metav Werkzeuge or consult the Metav advisors for specification guidance. Ceramic gauge block 1.28 mm, Grade 1 DIN 861/1 — precision reference gauge by Metav IndustryLine A Ceramic gauge block 1.28 mm, Grade 1 DIN 861/1 designed as a stable reference for calibration benches, laboratory use and workshop inspection routines. Ceramic for low thermal expansion Grade 1 accuracy per DIN 861/1 Nominal size 1.28 mm Lightweight 0.002 kg Reference accuracy for repeatable measurements The compact reference is manufactured for Grade 1 tolerance according to DIN 861/1, offering a predictable limit for comparative length checks. With a nominal length of 1.28 mm, the block serves as a micro reference in sets or as an individual standard for fine inspection tasks. The clearly defined grade allows engineers and technicians to plan tolerance stacks and gauge comparisons on a rational basis, reducing rework and inspection uncertainty through consistent reference values. The combination of standard conformity and a small nominal size makes it suitable where tight traceability and predictable measurement behaviour are required. Stable ceramic material for long service life Made from high-performance ceramic, the block provides low thermal expansion and excellent wear resistance compared with many metallic standards. This material choice yields improved dimensional stability over short-term temperature fluctuations and resists corrosion and magnetic interference in typical workshop environments. The result is a reference standard that preserves its geometry during routine handling, contributing to longer intervals between verification and fewer replacements. The low mass (approx. 0.002 kg) also simplifies handling when assembling precision sets or loading comparator fixtures. Practical use in calibration and inspection workflows As a compact gauge block the item integrates readily into master sets, comparator checks and laboratory reference chains. Its small footprint allows use in micro-assembly inspection, tool setting, and spot checks on production lines where space is limited but repeatability is essential. The clearly stated conformity to DIN 861/1 aids documentation and selection for quality systems and inspection plans. By using a defined, stable reference such as this block, process engineers achieve faster acceptance of measurement results and a clearer justification for decisions in quality assurance. For traceable reference standards choose the Metav IndustryLine ceramic gauge block and contact Metav Werkzeuge in Emmerich for personalised advice and reliable supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: M324.001.28 GTIN: 4054469142654 Customs tariff number: 90173000 Manufacturer: Metav IndustryLine Label: Keramik-Endmaß 1,28mm, Güte 1 DIN 861/1 Facts Nominal size: 1.28 mm Weight: 0.002 kg Grade: 1 (DIN 861/1) Material: Ceramic Category: Gauge blocks / End gauges Special features Ceramic material for low thermal expansion Grade 1 accuracy per DIN 861/1 Compact reference for micro measurements Lightweight design for easy handling FAQ What material and accuracy class does this gauge block have? The ceramic gauge block 1.28 mm, Grade 1 DIN 861/1 is made from ceramic and conforms to Grade 1 accuracy under DIN 861/1 for precision reference use. Can the gauge block be used in a laboratory comparator chain? Yes, the Metav IndustryLine ceramic gauge block is suitable as a stable reference within comparator chains and laboratory measurement setups. Is the block suitable for workshop spot checks and tool setting? The compact 1.28 mm nominal size makes the gauge block appropriate for micro-assembly inspections, tool setting and spot checks where a small, stable standard is required. How should the block be handled to preserve accuracy? Handle the ceramic gauge block with care, avoiding impacts and rapid temperature changes; store in a clean, dry environment to maintain dimensional stability. What identification helps with procurement and traceability? Use the article number M324.001.28 and GTIN 4054469142654 for ordering and traceability of the ceramic gauge block. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
ensure traceable length calibration with gauge blocks
gauge blocks, also called slip gauges or end gauges, are precision length standards designed to transfer exact measures during calibration and setup. Manufactured and graded for metrological use, they provide the reference dimensions needed to verify and adjust measuring instruments in industrial workshops and calibration labs.
how gauge blocks work and where they are essential
gauge blocks are used to create known lengths by wringing individual blocks together or by using a single block as a reference. length calibration in industry commonly relies on parallel gauge blocks, while angle, cylinder and sphere end gauges serve specialised tasks. these blocks are produced in steel, ceramic or carbide, and their material choice balances wear resistance with thermal behaviour. regular calibration—typically performed annually—by DAkkS-accredited laboratories ensures traceability. the highest-precision reference work, class K, is certified by the PTB using laser techniques; classes 0, 1 and 2 are tested under progressively less controlled conditions (class 0 in a climate-controlled lab, class 1 in a standard measurement room, class 2 in production).
measurable benefits that cut downtime and uncertainty
- consistent, traceable length standards reduce rework and measurement disputes by enabling reliable instrument calibration.
- choosing the correct material (steel, ceramic, carbide) extends service life and limits wear in high-use environments.
- selecting the right accuracy class (K, 0, 1 or 2) matches calibration effort to application needs and avoids over‑specification.
- annual calibration by accredited labs maintains documented compliance and supports quality systems such as ISO.
why Metav is a smart partner for precision standards
Metav combines specialist knowledge with a broad range of measurement technology, making the procurement of gauge blocks straightforward and dependable. with over 48,000 customers and more than 250,000 products stocked from Emmerich, Metav acts as a pragmatic quality filter for European workshops, reducing supplier complexity and ensuring consistent supply.
In short, gauge blocks deliver traceable, material‑appropriate and class‑matched references that keep calibration workflows efficient and auditable.
faq
what materials are gauge blocks available in and why does it matter?
gauge blocks are typically supplied in steel, ceramic or carbide. material choice affects wear resistance, stability and thermal expansion; selecting the right material for your environment optimises longevity and measurement stability.
how often should gauge blocks be calibrated?
industry practice is an annual calibration cycle, carried out by DAkkS-accredited laboratories, though frequency can be increased depending on usage and required uncertainty.
what do the accuracy classes k, 0, 1 and 2 indicate?
the classes denote graded tolerances and test conditions: K is the highest precision (certified by PTB with laser measurement), class 0 is checked under climate-controlled lab conditions, class 1 in a normal measurement room and class 2 in production environments.
are parallel gauge blocks always used for length calibration?
yes; for length calibration the parallel gauge blocks are the primary standard because they provide exact planar faces for wringing and stacking to create precise lengths.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com