Precision micrometers for reliable dimensional control
Micrometers deliver precise length and depth measurements in metalworking, enabling repeatable control over component tolerances and process stability. These instruments—available as outside micrometers, inside micrometers and depth micrometers—offer hardened contact faces and fine-thread spindles to ensure long-term accuracy and resistance to wear, with digital versions providing data transfer via USB or Bluetooth for seamless integration into inspection software. Typical uses include measuring small bores, depths and diameters in precision engineering, where features must be defined to micrometre-level accuracy; features such as ratchet thimbles and insulated frames help maintain consistent measuring force and temperature compensation. Choose between robust analog models, IP54-protected digital micrometers or micrometers with an integrated minicomputer for advanced functions like unit conversion, temperature correction and Go/NoGo evaluations.
1000-2000mm Repair Set for Large-Range Micrometer Anvil With Two Spacer Sleeves - Metav IndustryLine
Combining a solid measuring anvil with two precision distance sleeves (50 mm and 100 mm), this repair set restores reliable contact geometry for long-format instruments and helps maintain repeatable results. Order the M304.040.2 directly via Metav Werkzeuge or consult our technical team if compatibility advice is required. Repair set for large-range calipers — measuring anvil + 50 / 100 mm distance sleeves (Metav IndustryLine) The Repair set for large-range calipers (M304.040.2) supplies a replacement anvil and two distance sleeves to refurbish long-format measuring instruments used in heavy workshop and fixture applications. Measuring anvil plus 50 mm and 100 mm sleeves Suited for long-range calipers 1,000–2,000 mm Restores repeatability and profile stiffness Designed for long-format measurement tasks and mechanical stability The kit is intended for long-range measuring frames and calipers with a measuring span of 1,000–2,000 mm, a category where profile stiffness and reproducible contact points are decisive for reliable results. Replacing a worn contact anvil and adding the correctly sized distance sleeves ensures the original bearing geometry is regained. For workshop managers and fitters this translates into fewer rejected parts, a reduction in rework and better throughput because installed contacts preserve the instrument’s repeatability over extended lengths. Fast refurbishment to reduce downtime and restore performance A targeted repair with the anvil and two sleeves is a pragmatic alternative to full instrument replacement. The set enables straightforward component changeover that is both time-efficient and cost-effective, increasing net equipment availability. Because the components are supplied as a matched set, alignment and seating are simplified and the profile stiffness of the measuring face is re-established, which supports consistent readings across the instrument’s long measuring range. This approach suits maintenance workshops and toolrooms that require predictable measurement behaviour. Practical precision for workshops and production lines Although the kit does not include a calibration certificate by default, the components are packaged to industry expectations and clearly identified for traceability (GTIN and SKU supplied). Using the correct anvil geometry and sleeve length reduces measurement uncertainty originating from contact deformation and uneven seating. The lightweight kit (approx. 1 kg) is easy to handle when fitting to large calipers or comparable measuring frames. For operators who need a reliable spare-part solution, the set offers a focused way to maintain measurement quality without extensive downtime. Contact Metav Werkzeuge today to confirm fitment for specific large-format calipers and secure the M304.040.2 repair set for prompt restoration of measuring capability Technical data Article number: M304.040.2 GTIN: 4054469116013 ECLASS: 21043590 Customs tariff: 90173000 Core specifications Suitable measuring range: 1,000–2,000 mm Sleeve sizes: 50 mm, 100 mm Weight: 1 kg Features Brand: Metav IndustryLine Category path: Measuring instruments › Accessories Short description: Measuring anvil + distance sleeves 50 mm, 100 mm FAQ Which instruments are compatible with this repair set? The repair set is intended for long-format calipers and comparable measuring frames with a measuring range of 1,000–2,000 mm; verify the contact interface on the instrument against the M304.040.2 specifications before ordering. What exactly is supplied with the kit? The M304.040.2 contains a replacement measuring anvil and two distance sleeves (50 mm and 100 mm) as described in the product label and technical data. Can the set be used to restore repeatability on large calipers? Yes — replacing worn contact faces with the matched anvil and sleeves in this kit helps to re-establish correct contact geometry and improves repeatability for long-range measurements. Is professional recalibration included after fitting the components? The kit does not automatically include recalibration; users should arrange calibration according to their internal quality procedures if a documented verification is required after replacement. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000-3000mm Rod Internal Measuring Set 0.01mm Resolution Ø28mm, Supplied With Extensions In Case - Metav IndustryLine
Take advantage of the combination of a 1,000–3,000 mm measuring range, a fine 0.01 mm resolution and a stiff Ø 28 mm rod to measure long internal bores with confidence; the modular extension set reduces retooling and speeds inspection cycles. Order the set via Metav Werkzeuge or consult their specialists for application-specific advice. M310.066 Rod internal measuring set — 1,000–3,000 mm, 0.01 mm (Metav IndustryLine) M310.066 Rod internal measuring set is a precision kit for reliable internal bore measurement across long components in workshops, jig and fixture shops, and quality control. 1,000–3,000 mm measuring range 0.01 mm analogue readout accuracy Ø 28 mm rigid rod for repeatable readings Modular extension set included Precise inspection across long bores for consistent quality Engineered for long-range internal measurements, this rod measuring kit delivers a 1,000–3,000 mm measuring range with an analogue 0.01 mm resolution, making it suitable for large housings, cylinder bores and segmented assemblies. The combination of extended reach and fine reading reduces the need for multiple instruments and speeds up the inspection process, which supports a more efficient production flow and fewer measurement transfers between tools. Modular extensions that simplify set-up and adaptation The set includes a range of extensions (50 / 100 / 100 / 200 / 500 / 1000 mm) that allow fast configuration for different bore depths and staged measurements. The modular concept means the same base rod can be adapted to a wide variety of component sizes, lowering inventory needs and shortening set-up times. Clear, repeatable mechanical connections ensure that adjustments remain stable during measurement sequences, improving reproducibility. Stiff, workshop-ready construction for dependable handling A 28 mm shaft diameter gives the instrument the necessary stiffness to keep deflection low over long spans, while the overall mass (approx. 6 kg) signals substantial build quality for routine use. The analogue mechanical display provides an intuitive, direct readout that requires no batteries, ideal for rough environments or remote inspection locations. The robust design supports daily workshop handling and contributes to consistent measurement results. Benefits for quality control and production throughput With its long reach and fine reading, the set is primarily a rational choice where traceable, repeatable measurements are essential: fewer tool changes, faster cycle times and clearer pass/fail decisions. The product’s modularity also enables quicker adaptation to incoming workpieces, which helps maintain throughput without compromising on measurement fidelity. Contact Metav Werkzeuge for tailored advice on using this Metav IndustryLine internal measuring rod set and to discuss compatibility with specific bore geometries Technical data Article number: M310.066 GTIN: 4054469119021 Customs tariff number: 90173000 Weight: 6 kg Type: Analogue internal measuring rod set Facts Measuring range: 1,000–3,000 mm Readout: 0.01 mm Rod diameter: 28 mm Special features Set with extensions: 50 / 100 / 100 / 200 / 500 / 1000 mm Designed for long internal bore measurement Category: Measuring screws / internal measuring rods Suitable for workshop and quality inspection use Intuitive mechanical readout, no battery required FAQ What measuring range does the set cover? The set covers a measuring range from 1,000 mm to 3,000 mm, delivered as a modular rod system that can be configured with the included extensions. How fine is the resolution and how is it read? Resolution is 0.01 mm and the measurement is shown via an analogue mechanical readout that provides direct, battery-free readings. Are extensions included and which lengths are supplied? Yes — the set includes extensions of 50, 100, 100, 200, 500 and 1000 mm to assemble the required total length for a given inspection task. Is the kit suitable for heavy workshop use? The Ø 28 mm shaft and solid construction make the kit robust enough for routine workshop inspection of long bores and large components. Can this set handle measurements of segmented or stepped bores? The modular extension concept and stable rod geometry allow adaptation to segmented or stepped internal geometries when set up appropriately. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Digital Micrometer With IP65 Protection, ISO 17025 Calibrated - Microtech Metrology
Reliable inspection of large components is achieved through a combination of a 900–1000 mm measuring range, IP65 protection and an ISO 17025 calibration certificate, together with an instrument accuracy of ±0.015 mm and a friction ratchet for repeatable contact pressure. Order the micrometer directly via Metav Werkzeuge or ask our consultants if needed. Micrometer (outside micrometer) – digital, 900–1000 mm range | Microtech Metrology The micrometer is a large-range digital measuring instrument designed for accurate inspection of heavy-duty shafts, bearings and production components in workshop and quality-control environments. Large 900–1000 mm range IP65 protection for shop-floor use ISO 17025 calibration certificate included Friction ratchet for repeatable pressure Precise long-reach inspection for production control The large measuring span of 900–1000 mm enables direct inspection of long shafts and assemblies without transfers or jigs, reducing handling time and potential alignment error. With an accuracy of ±0.015 mm, the instrument delivers reproducible results suitable for incoming inspection and final acceptance tests. The digital readout with 0.001 mm resolution shortens reading time and lowers operator influence, while the integrated friction ratchet stabilises contact pressure so serial measurements remain consistent. Robust engineering for workshop conditions Constructed for use in busy manufacturing areas, the device features IP65 protection, safeguarding electronics against coolant spray and dust ingress. The sizeable Ø25 mm measuring faces distribute contact forces and are appropriate for cylindrical and flat surfaces encountered in heavy machining. At a measured weight of 6.7 kg, the design balances mass for stability with practical handling during bench inspection. The digital micrometer head resists the shop-floor environment while providing clear numeric feedback for quick decisions. Traceable calibration and delivery ready for use This micrometer is delivered with a full ISO 17025 calibration certificate, ensuring traceability and documented measurement uncertainty for quality systems. Setting rods are supplied as part of the delivery, permitting immediate verification and adjustment on receipt. The included calibration documentation supports audit requirements and simplifies integration into a documented measurement programme for production or laboratory use. Designed for organised workflows and repeatability The combination of a large range, digital resolution and friction ratchet reduces setup steps and accelerates batch inspection, supporting efficient quality routines. The instrument's format is suitable for line-side measurement stations or metrology benches where fewer measurement steps and consistent contact conditions matter. Integration into established inspection plans is straightforward thanks to its calibrated status and robust shop-floor protection. Discuss Microtech Metrology's calibrated digital micrometer and its suitability for inspection tasks with Metav Werkzeuge in Emmerich — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical Data SKU: 110171101 GTIN: 4061905040399 Manufacturer: Microtech Metrology Type: Digital micrometer Facts Measuring range: 900–1000 mm Resolution: 0.001 mm Accuracy: ±0.015 mm Weight: 6.7 kg Measuring faces: Ø25 mm Protection class: IP65 Special features ISO 17025 calibration certificate included Friction ratchet Setting rods included IP65-protected digital micrometer head Large-range design for heavy components FAQ What measuring range does the micrometer cover? The micrometer covers a measuring range of 900–1000 mm, making it suitable for long shafts and oversized components. Is the instrument delivered calibrated and traceable? Yes, the micrometer is supplied with a calibration certificate issued to ISO 17025, providing traceability and documented measurement uncertainty. What accuracy and resolution can be expected? The instrument provides an accuracy of ±0.015 mm with a digital resolution of 0.001 mm for fine readout and reproducible inspection results. Can the micrometer be used on the shop floor? Yes, the device has IP65 protection, which protects the digital head against dust and spray, making it appropriate for many workshop environments. What features help ensure repeatable measurements? The friction ratchet ensures consistent contact pressure, while the Ø25 mm measuring faces distribute load for stable readings. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
1000mm Extension Rod Ø28mm For Internal Gauge Sets - Metav IndustryLine
Take advantage of the 1000 mm length and Ø 28 mm shaft to extend measurement range with minimal tooling changes; compatible mounting with the 310.065/310.066/310.067 series ensures fast integration and consistent stiffness — order the extension rod directly via Metav Werkzeuge or consult the team for application advice. M310.066.1 — 1000 mm Extension Rod Ø 28 mm (for 310.065 / 310.066 / 310.067) M310.066.1 is a 1‑metre extension rod designed to increase the measuring reach of compatible rod‑type internal measuring screw sets, suited for larger workpieces and fixtures in workshop and industrial environments Compatible with 310.065/310.066/310.067 Provides 1000 mm extended measuring reach Robust Ø 28 mm shaft for reduced deflection Measure larger components without new gauges The 1000 mm extension rod expands the reach of existing rod‑type internal measuring screw sets so larger components can be checked without buying separate gauges. By extending the measuring range, measurement cycles are consolidated and setup times are reduced. This approach preserves the original measuring head and its calibration traceability while enabling checks of longer bores, housings and assemblies that would otherwise require alternative fixtures. Maintain stiffness for reproducible readings A Ø 28 mm shaft delivers higher stiffness than slimmer extensions, lowering elastic deflection over the full metre length and improving repeatability when measuring extended features. The solid construction and nominal mass contribute to stable contact behaviour under normal measuring force, which helps to reduce variability introduced by operator handling. In practical terms, the increased rigidity promotes more reliable comparative measurements and better process control. Simple integration into existing sets and workflows Designed for straightforward interfacing with the 310.065 / 310.066 / 310.067 series, the extension rod requires no special adapters in most assemblies and slots into established inspection routines. Compatibility reduces spare‑parts variety and inventory overhead, enabling workshop managers to standardise on a single extension solution for multiple measuring heads. Faster assembly and fewer changeovers support higher throughput in serial inspection tasks. Built for workshop and industrial conditions The extension rod is intended for regular use in machine shops and quality departments where handling and transport are frequent. A compact handling profile and robust diameter balance reach and usability, making it suitable for fixtures and jigs used in production and toolrooms. Supplied by Metav IndustryLine, the accessory benefits from the supplier’s emphasis on dependable supply and testing standards, ensuring predictable delivery to the workbench. Contact Metav Werkzeuge for compatibility checks and delivery from Emmerich; the Metav team can advise on integrating the Metav IndustryLine extension rod into existing inspection setups Technical data SKU: M310.066.1 GTIN: 4054469119038 Manufacturer: Metav IndustryLine Length: 1000 mm Shaft diameter: Ø 28 mm Weight: 6 kg Customs tariff number: 90173000 eClass: 21019104 ETIM: EC002219 Compatible with models 310.065, 310.066, 310.067 Category: Zubehör (accessory) Intended use: extend measuring reach of rod internal measuring screw sets Story trigger: accessory FAQ How does the extension rod attach to existing measuring sets? The extension rod is designed for plug‑in compatibility with the 310.065 / 310.066 / 310.067 series; M310.066.1 interfaces with the same connector geometry used by those rod‑type internal measuring screw sets. Will using the 1000 mm extension affect measurement repeatability? Longer extensions introduce more potential for deflection, but the Ø 28 mm diameter and robust construction of M310.066.1 help maintain repeatability compared with slimmer alternatives. For which applications is this extension most suitable? The extension rod is ideal for measuring longer bores, housings and assemblies where increasing the reach of rod‑type measuring heads avoids separate gauges or extensive fixture modifications. Is the extension rod supplied with calibration or certification? The product description does not specify calibration status; for details about delivered calibration certificates, request confirmation from Metav Werkzeuge when ordering M310.066.1. Can the extension be used in automated inspection stations? Yes — the simple mechanical interface and consistent geometry make M310.066.1 suitable for integration into fixtures and automated setups provided the station accommodates the 1000 mm length and mass. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Rod Internal Measuring Set 50–1000mm Range, 0.01mm Resolution, Includes Extensions, Plastic Case - Metav IndustryLine
Benefit from the combination of an extensive 50–1000 mm measuring range, fine 0.01 mm resolution and a complete set of extension rods for reproducible internal measurements; order the Inside Micrometer Set directly via Metav Werkzeuge or consult our advisors for specifications and delivery options. Inside Micrometer Set M310.064 — Rod-type, 50–1000 mm, 0.01 mm (Metav IndustryLine) The Inside Micrometer Set M310.064 is a rod-type inside micrometer kit designed for precision measurement of large internal diameters on machining centres, inspection benches and assembly jigs. Measuring range 50–1000 mm Resolution 0.01 mm Rod-type inside micrometer set Extension rods included Ready for large-bore measurement with practical reach and control The rod-style construction provides a continuous measuring span from 50–1000 mm, making the set suitable for bores, housings and large fixtures where a single instrument must cover many diameters. The modular rod concept reduces handling time compared with multiple fixed gauges and enables access to deep bores without improvised adapters. Built as a workshop-capable set, the kit supports consistent repeatability across a range of component sizes while preserving rigidity during measurement. Precise analogue reading for reliable pass/fail checks With an analogue scale resolving 0.01 mm, the instrument offers fine graduations for routine quality control tasks. The mechanical scale format combines tactile feedback with straightforward interpretation, which benefits inspection staff accustomed to analogue instruments. Clear graduations reduce read-back errors and, together with the robust measuring faces, support reliable dimensional checks during in-process and final inspection stages. Complete accessory suite that reduces setup times The set includes a comprehensive selection of extension rods (13, 25, 50, 2×100, 150, 200, 300 mm), supplied to span wide depths without intermediate joins. This accessory configuration simplifies configuration for stepped or deep internal measurements and limits the need for additional tooling. The modular rods and the set format also streamline inventory management in production and quality departments, supplying a single solution for multiple measurement tasks. Durable construction focused on workshop conditions Mechanical components are engineered for repetitive use in industrial environments; the presence of dedicated measuring faces improves contact stability and wear resistance. The overall assembly weight of approximately 3 kg reflects a balance between portability and solid feel during measurement. As a purpose-built inside micrometer set, it supports regular inspection routines while providing the service life expected in machine shops and toolrooms. For project-specific enquiries or availability, contact Metav Werkzeuge to discuss the Metav IndustryLine inside micrometer set and receive tailored advice on configuration and delivery Technical data SKU: M310.064 GTIN: 4054469119007 ECLASS: 21170335 ETIM: EC003590 Customs tariff number: 90173000 Core specifications Measuring range: 50–1000 mm Resolution: 0.01 mm Weight: 3 kg Rod diameter: 15.5 mm Analogue instrument: yes Features / accessories Set: inside micrometer rods, modular design Extension rods included: 13, 25, 50, 2×100, 150, 200, 300 mm Measuring faces: included Category: Micrometers (inside) FAQ Which internal diameters can be measured with this set? The Inside Micrometer Set M310.064 covers internal diameters from 50 mm up to 1000 mm, using the modular rods to reach deep and stepped bores. What resolution and repeatability does the instrument offer? Resolution is 0.01 mm on the analogue scale; the mechanical design supports consistent repeatability appropriate for workshop inspection routines. Which accessories are supplied with the set? The set includes extension rods in lengths 13, 25, 50, 2×100, 150, 200 and 300 mm to cover a wide variety of depths without additional adapters. Is the instrument suitable for use in a production environment? Yes, the rod-type configuration and robust measuring faces make the kit suitable for regular use in machine shops, assembly lines and quality departments. Can the set be used for deep or stepped bore measurements? The modular rods and wide measuring span are intended specifically for deep and stepped bores, reducing the need for multiple fixed gauges. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
1000mm Three-Point Bore Micrometer Colour Touchscreen Wireless+USB, ISO 17025 Calibrated - Microtech Metrology
Take advantage of the combination of high-resolution readout, Wireless + USB data transfer and certified ISO 17025 calibration for repeatable, traceable inside measurements across a 200–1,000 mm range — ideal for metrology labs and toolrooms. Order the three-point inside micrometer directly via Metav Werkzeuge or consult our specialists for application advice. Three-Point Inside Micrometer by Microtech Metrology — 200–1,000 mm, Colour 1.5" Touchscreen Three-Point Inside Micrometer for precise bore and internal diameter measurement in production control and inspection environments ISO 17025 calibrated with certificate Wireless and USB data output Colour 1.5" touchscreen readout Measuring range 200–1000 mm Traceable accuracy for critical bores The three‑point measuring system ensures stable contact with the bore, reducing eccentricity and improving repeatability for internal diameters. With a measuring range of 200–1,000 mm and an indicated accuracy of ±0.011 mm, the instrument is suited to routine quality checks and first‑article inspection where clear, verifiable results are required. The device’s resolution of 0.0001 mm is shown on a Colour 1.5" touchscreen, making fine adjustments and readings straightforward and reducing interpretation errors. Fast data capture and seamless workflow Equipped with Wireless and USB data output, the micrometer integrates into digital inspection chains and statistical process control systems without manual transcription. The touchscreen display speeds up set‑up and verification, while electronic export removes transcription risk and accelerates reporting. These features support efficient inspection cycles and shorter process feedback loops, helping to maintain production throughput without compromising measurement integrity. Built for large internal measurements The instrument’s capacity and construction are geared towards larger bores: a measuring depth of 1,150 mm provides access to deep features and recesses commonly found in valves, housings and large assemblies. Classified in the large‑range class (500–1,000 mm), this solution balances reach and rigidity to preserve reproducibility across the full span. The included setting ring facilitates quick verification and zeroing at the bench, keeping downtime to a minimum. Certified calibration and field application Supplied fully calibrated to ISO 17025, the micrometer comes with a traceable calibration certificate, allowing direct use in accredited workflows and ensuring measurement results are defensible in quality documentation. Typical applications include inspection of bores in hydraulic components, mould housings and rotors where internal geometry is critical. The electronic readout and data outputs also make the instrument suitable for laboratories implementing Industry 4.0 data capture. For measurement tasks requiring traceable, large‑range internal accuracy, contact Metav Werkzeuge to discuss this Microtech Metrology three‑point inside micrometer and its integration into existing inspection procedures; email info@metav-werkzeuge.com or phone +49 2822 7131930 for purchase and technical consultation. Technical data Article number: 133790011 GTIN: 4061905074332 Manufacturer: Microtech Metrology Facts Measuring range: 200–1,000 mm Measuring depth: 1,150 mm Resolution: 0.0001 mm Accuracy: ±0.011 mm Display: Colour 1.5" touchscreen Data output: Wireless, USB ECLASS: 21170335 ETIM: EC003590 Supplied calibrated to ISO 17025 with certificate Special features Three‑point measuring system Digital readout with touchscreen Setting ring included Wireless + USB data output Digital instrument for metrology applications FAQ What measuring range does the instrument cover? The three‑point inside micrometer covers a measuring range from 200 to 1,000 mm, suitable for large internal diameters and deep features. Is the micrometer delivered calibrated? Yes — the instrument is supplied fully calibrated to ISO 17025 and includes a traceable calibration certificate for immediate use in accredited processes. How are readings exported from the instrument? Readings can be exported via Wireless connection or USB, enabling integration with inspection software and SPC systems. What accuracy and resolution can be expected? The instrument provides an indicated accuracy of ±0.011 mm and a display resolution of 0.0001 mm, suitable for demanding inspection tasks. Which applications is this micrometer intended for? Typical uses include bore inspection in hydraulic components, mould and tool fittings, and larger assemblies where reproducible internal measurements are required. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
100mm Depth Gauge Flat Bridge Simple Interchangeable Measuring Inserts, Ratchet, Case - Metav IndustryLine
Combine high reproducibility, a ratchet drive and easily interchangeable measuring inserts for dependable depth checks in fine mechanical and workshop settings. Order the M309.070 directly via Metav Werkzeuge or contact our consultants for additional specification support. M309.070 Depth Micrometer — Flat Anvils, 0–100 mm, 0.01 mm resolution (Metav IndustryLine) The M309.070 depth micrometer is a compact, ratchet‑driven depth gauge for precise depth measurement tasks across fine mechanical and standard workshop applications. 0.01 mm resolution for fine measurements ±0.005 mm accuracy for reproducible results Ratchet drive for consistent measuring force Supplied with interchangeable rods and protective case Precision that reduces rework and inspection time The gauge delivers a 0–100 mm measuring range with an analogue 0.01 mm graduation and an indicated accuracy of ±0.005 mm, making it suitable where repeatable depth readings are required. The fine graduation supports clear, unambiguous readings while the high stated accuracy helps to reduce measurement uncertainty and downstream rework. The mechanical scale and robust construction make the instrument a practical choice for routine quality checks and setup tasks, providing a reliable baseline for process control. Consistent handling and rapid changeover A ratchet drive ensures a uniform measuring force on every reading, which lowers operator‑introduced variation and improves reproducibility. The design allows easy replacement of measuring inserts, while four extension rods are included to cover small incremental ranges without swapping instruments. These features combine to shorten cycle times for serial checks and to simplify measurements on stepped or recessed features. The compact bridge and flat measuring faces support stable seating on the workpiece for repeatable results. Portable protection and workshop readiness Supplied in a protective case, the instrument is ready for transport and safe storage, reducing the risk of damage between uses. The set includes four measuring rods and is engineered for routine workshop environments where robust handling and quick set‑up matter. Its compact form factor makes it particularly well suited to bench work and fine mechanical assemblies, delivering a balance of reach and stiffness that aids practical measurement tasks. Choose the Metav IndustryLine M309.070 for reliable depth measurement — contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for technical advice and secure supply from our European distribution centre Technical data Article number: M309.070 GTIN: 4054469117744 Category: Messschrauben Brand: Metav IndustryLine Core data Measuring range: 0–100 mm Resolution: 0.01 mm Accuracy: ±0.005 mm Ratchet drive: yes Bridge dimensions: 100 x 16 mm Special features Flat measuring faces Interchangeable measuring inserts Supplied with four extension rods Delivered in protective case Analogue reading scale FAQ What measuring range and resolution does this set offer? The M309.070 depth micrometer covers a 0–100 mm range with an analogue graduation of 0.01 mm for fine depth readings. Which accessories are included with the instrument? The delivery for the M309.070 comprises a protective case and four measuring rods; interchangeable measuring inserts are provided for flexible measurement set‑ups. How does the ratchet drive affect measurement quality? The ratchet mechanism on the M309.070 ensures a consistent measuring force for each reading, reducing operator variation and improving reproducibility across repeated checks. For which tasks is this depth micrometer best suited? This compact, ratchet‑equipped gauge is ideal for fine mechanical work and standard workshop depth checks where repeatability, quick set‑up and protected transport are required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Depth Gauge Round Bridge 0.01mm Resolution Replaceable Measuring Inserts, Supplied in Case - Metav IndustryLine
Take advantage of precise depth measurement with reliable repeatability and user‑friendly handling: the instrument combines ±0.005 mm accuracy with a 0.01 mm reading scale and a ratchet stop for reproducible contact force. Order the depth micrometer directly via Metav Werkzeuge or contact our consultants for application advice. M309.060 — Depth micrometer (0–100 mm) with ratchet stop and curved anvils The M309.060 is a precision depth micrometer designed for workshop and inspection tasks, offering fine resolution and a practical accessory set for routine depth measurements up to 100 mm. 0–100 mm measuring range 0.01 mm reading resolution Ratchet stop for constant contact Curved measuring faces for reliable contact Precision that reduces rework and speeds inspection The instrument delivers high repeatability attributable to its fine mechanical design and ratchet stop, which stabilises the measuring force and reduces operator‑induced variation. With a reading resolution of 0.01 mm and a declared accuracy of ±0.005 mm, this analogue depth gauge fits routine quality control where tight tolerances are required. The design supports consistent results across repeated measurements, so batch inspection becomes more predictable and corrective cycles are reduced. Practical features that make measurement faster Built for workshop efficiency, the device includes a set of four interchangeable measuring rods and a quick‑change system for the measuring inserts, enabling fast adaptation to different depths without disrupting workflow. The curved measuring faces ensure secure contact on uneven surfaces and small bores, improving stability during depth readings. The mechanical construction is straightforward to service, minimising downtime and keeping throughput steady. Ergonomics and handling that protect measurement integrity A dedicated ratchet stop provides uniform tightening and prevents over‑loading of the spindle, while the compact bridge design suits bench and fixture work where manoeuvrability matters. The analogue scale is intuitive for users familiar with mechanical gauges and requires no batteries, which simplifies long‑term operational readiness. The combination of robust handling and accessible maintenance supports continuous use in production environments. Suited classification and typical applications This depth micrometer sits within the standard measuring‑range class for workshop metrology and is appropriate for component inspection, jig and fixture checks, and depth verification in machining operations. Its capability set addresses everyday needs in metalworking and general engineering, adding measurable control to assembly and inspection processes. Contact Metav Werkzeuge today for detailed application guidance or to request a tailored delivery proposal for the M309.060 depth micrometer Technical data SKU: M309.060 GTIN: 4054469117720 EClass: 21170350 ETIM: EC003590 Tariff number: 90173000 Facts Measuring range: 0–100 mm Reading resolution: 0.01 mm Declared accuracy: ±0.005 mm Bridge dimension: 100 x 16 mm Pickup / spindle interface: 4.5 Special features Analogue mechanical instrument Ratchet stop for consistent measuring force Curved measuring faces for secure contact Easy replacement of measuring inserts Accessories included: measuring rods, 4 pcs Category: micrometer screw gauges (depth micrometer) FAQ What measuring range does this depth micrometer cover? The M309.060 depth micrometer covers a measuring range from 0 to 100 mm, suitable for standard workshop depth checks. What are the resolution and declared accuracy? Resolution is 0.01 mm with a declared accuracy of ±0.005 mm for the M309.060, providing fine control for routine inspection tasks. Which measurement situations is the instrument best for? The instrument is intended for depth verification in machining, fixture set‑up and component inspection where stable contact and repeatable results are required. Are accessories included with delivery? Yes — delivery includes four measuring rods and the quick‑change measuring insert system to adapt swiftly to different depths. Is the gauge battery‑free and easy to maintain? As an analogue mechanical instrument, the gauge requires no batteries and features simple replaceable inserts for straightforward maintenance. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Digital Depth Gauge Flat Bridge 100mm, 0.001mm Resolution, Ratchet, Supplied In Case - Metav IndustryLine
Combining micrometre-capable resolution with a compact 0–100 mm measuring range, this flat digital depth gauge delivers repeatable, workshop-ready results and reduces rework. Benefit from consistent contact force, fast read-out and easy serviceability — order directly via Metav Werkzeuge or request tailored advice from our consultants. M302.170.C — Digital flat depth gauge, 0–100 mm, 0.001 mm resolution (Metav IndustryLine) M302.170.C is a digital flat depth gauge designed for precise depth checks in fine mechanical and workshop environments, offering a compact footprint and reliable digital output. Flat digital depth gauge, 0–100 mm range Resolution 0.001 mm, accuracy ±0.005 mm Ratchet drive for consistent measuring force Easy replacement of measuring inserts Precise measurement where repeatability matters The M302.170.C depth gauge combines a compact measuring span with a high resolution of 0.001 mm (0.00005 in), making it suitable for tasks that demand micrometre-level differentiation without complex setups. The instrument’s stated accuracy of ±0.005 mm supports quality control steps where traceable repeatability reduces inspection time. The flat contact faces provide stable seating on workpieces, while the ratchet mechanism assures a consistent measuring force to limit operator‑introduced variability. These elements together improve throughput in inspection benches and small-batch production runs. Workflow benefits and integration-ready output Designed for integration into data-driven workflows, the gauge features a digital display with ON/OFF, ABS/INC, UNIT and SET functions for quick mode changes and unit selection. Measurement data can be exported via the RB 4.1 interface, allowing direct capture into inspection software or SPC systems and eliminating manual transcription errors. The tool ships with measuring rods included (4 pieces), reducing the need for immediate accessory purchases and enabling fast set-up at the workstation. Easy replacement of the measuring inserts lowers downtime and keeps the tool in service longer. Compact class for fine and micro components Classified in the micro range with a maximum span of 0–100 mm, this flat depth gauge is tailored to fine mechanical work such as small assemblies, precision fixtures and watchmaking tasks where short, stiff measuring jaws are advantageous. The 100 x 16 mm bridge offers a stable beam geometry for localised depth checks while remaining manoeuvrable on the shop floor. The combination of compact design, digital read-out and a robust output interface makes the instrument a practical option for laboratories and production lines that require clear, rapid depth verification without excessive complexity. Contact Metav Werkzeuge for a technical consultation to confirm fitment and delivery options for the M302.170.C digital flat depth gauge and its accessories Technical data Article number: M302.170.C GTIN: 4054469115108 eClass: 21170350 ETIM: EC003590 Customs tariff number: 90173000 Core specifications Measuring range: 0–100 mm Resolution: 0.001 mm / 0.00005 in Accuracy: ±0.005 mm Bridge dimensions: 100 x 16 mm Measuring faces: flat Data output: RB 4.1 Display functions: ON/OFF, ABS/INC, UNIT, SET Ratchet: yes Measuring rods included: 4 Special features Easy replacement of measuring inserts Digital output compatible with RB 4.1 systems Delivery in transport case Compact class: micro range suitable for fine mechanical work FAQ What resolution and accuracy does the gauge provide? The M302.170.C digital flat depth gauge offers a resolution of 0.001 mm (0.00005 in) and an accuracy of ±0.005 mm. Is a transport case and accessories included? Yes, the gauge is delivered in a transport case and includes four measuring rods to enable immediate use. Can measurement data be exported to external systems? The device is equipped with an RB 4.1 data output, enabling connection to data-collection and SPC systems for automated logging. For which applications is the gauge intended? Classified in the micro range (0–100 mm), it is ideal for fine mechanical work such as small components, fixtures and precision depth checks. Does the instrument ensure consistent measuring force? Yes, the integrated ratchet ensures consistent contact force, reducing variation from manual operation. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Digital Micrometer 0.001mm Resolution Friction Thimble Auto-Off, DIN 863, Plastic Case - Metav IndustryLine
Take advantage of the combination of 0.001 mm resolution, a 75–100 mm measuring range, and a friction thimble for repeatable contact pressure to speed up inspection routines; order directly via Metav Werkzeuge or consult the Metav team for tailored supply options. Digital Micrometer M302.007.N — 75–100 mm, 0.001 mm resolution (Metav IndustryLine) The Digital Micrometer M302.007.N is a precision external micrometer for workshop and quality-control applications, offering high-resolution digital readings and a robust measuring range for component inspection. High-resolution 0.001 mm reading Measuring range 75–100 mm Friction thimble for consistent pressure Digital display with ABS/INC/UNIT keys Faster, verifiable measurements for routine inspection The combination of a 0.001 mm display resolution and a clear digital interface accelerates routine dimension checks without sacrificing traceability. The instrument records readings with micrometre-level precision, enabling shorter inspection cycles and reliable go/no-go decisions. Conformity with DIN 863 supports acceptance in standardised workshop environments, while the digital display with ON/OFF/SET and ABS/INC/UNIT controls reduces interpretation errors common to analogue instruments. Consistent contact force and repeatability A friction thimble provides consistent contact pressure at each measurement, reducing variance from operator technique and improving repeatability across batches. The robust spindle and 6.5 mm measuring faces ensure a stable contact area for external measurements, while the auto-sleep function preserves battery life between uses. This combination of mechanical control and electronic readout makes the device suitable for production-line spot checks and precision checks in the metrology lab. Practical scope for workshop and production use With its 75–100 mm measuring range, the instrument covers medium-sized external dimensions frequently encountered in engineering workshops, maintenance departments and quality control stations. The compact digital micrometer is designed for efficient handling during serial part inspection and is rugged enough for daily workshop use. Fast, repeatable dimension checks shorten setup times and contribute to smoother production workflows. Traceability and integration into measurement routines The micrometer supports standard metrology practices with a readable digital output and straightforward operation. Numeric identifiers and classification data facilitate inventory and calibration planning. For traceability in quality management systems, the unit’s clear readout and industry-standard construction make it straightforward to incorporate into inspection records and work instructions, reinforcing reliable quality checks across shifts. Contact Metav Werkzeuge today to discuss how the Metav IndustryLine Digital Micrometer M302.007.N fits into existing inspection processes or to request volume supply and delivery options. Technical Data Article number: M302.007.N GTIN: 4054469113821 Category: Messschrauben (micrometers) eClass: 21170328 Core specifications Measuring range: 75–100 mm Resolution / reading: 0.001 mm Measuring faces: 6.5 mm Standard: DIN 863 Digital display: ON/OFF/SET and ABS/INC/UNIT Zolltarifnummer: 90173000 Special features Friction thimble for repeatable contact pressure Auto-off function to conserve battery Digital instrument (electronic readout) Suitable for external measurements FAQ Is this micrometer suitable for workshop-level quality control? Yes. The Digital Micrometer M302.007.N by Metav IndustryLine is designed for workshop and production inspection, offering a 75–100 mm range and a 0.001 mm display that support routine quality-control tasks. Does the device comply with any standards? The instrument is manufactured to meet DIN 863, which governs design and functional aspects for external micrometers and is widely accepted in industrial inspection. What readout and button functions are available? The micrometer features a digital display with ON/OFF/SET controls and ABS/INC/UNIT functions for toggling measurement modes and units. Is a calibration certificate included? The product data does not indicate an ISO 17025 calibration certificate; standard calibration status should be verified with Metav Werkzeuge if a specific calibration traceability is required. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Digital Micrometer 0.001mm Resolution, Ratchet, Plastic Case, DIN 863 - Metav IndustryLine
Take advantage of the combination of 1 µm resolution, a practical 75–100 mm measuring range and a ratchet thimble that ensures reproducible contact pressure; this delivers fast, traceable external measurements for workshop and QA routines. Order the instrument directly via Metav Werkzeuge or consult the technical team for integration advice. Digital Micrometer M302.293 — Digital micrometer with 75–100 mm range and 0.001 mm resolution (Metav IndustryLine) The Digital Micrometer M302.293 is a hand-held, externally focused measuring instrument designed for precise diameter and thickness checks in production and inspection environments. 75–100 mm measuring range, robust spindle 0.001 mm resolution for fine readings Ratchet thimble for constant measuring force Four-button digital display with ABS and HOLD Speed and accuracy that accelerate inspection A high-resolution 0.001 mm readout shortens decision cycles during incoming inspection and final checks without sacrificing reliability. The long, clear digital display with dedicated ON/0-, mm/inch, ABS and HOLD buttons reduces operator input and read-back errors, while the compact mass supports handheld operation across repeated measurements. Used in routine quality control, this configuration reduces time per measurement and delivers consistent numeric output for traceable documentation. Repeatable contact and robust measuring faces for dependable results Built with a ratchet thimble to ensure constant measuring pressure, the instrument minimises operator-induced variation, which is crucial when tolerances are tight. The hardened measuring faces and a measuring face diameter of 6.5 mm support stable contact geometry and long-term wear resistance. Constructed to comply with DIN 863, the design is targeted at practical shop‑floor use and laboratory sampling, offering a dependable balance between stiffness and manoeuvrability for external measurements in metalworking and component assembly. Digital functions that integrate with data workflows Equipped with a four‑button interface and RB 4 data output, the micrometer enables straightforward numeric transfer into data collectors or QC software where supported. The ability to switch between mm/inch and to freeze readings with HOLD speeds documentation and reduces transcription errors, improving throughput in batch inspection and SPC tasks. The instrument’s digital logic and clear controls make it suitable for operators with basic digital experience while preserving mechanical fundamentals. Engineered for everyday workshop and quality use The unit’s balanced weight and ergonomic form support repeated measurements across a production shift, while the precise resolution and standards compliance allow its use for serial quality checks and sample certification. As part of a broader measuring strategy, this micrometer fits well where a durable, accurate external gauge is required and complements lab-grade instruments when fast, reliable readings are needed on the shop floor. For tailored advice on application, data integration or delivery options, contact Metav Werkzeuge directly at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — the Metav team will advise on suitability and supply arrangements. Technical Data Article number: M302.293 GTIN: 4054469146454 eClass: 21170328 ETIM: EC003590 Norm: DIN 863 Facts Measuring range: 75–100 mm Resolution: 0.001 mm (1 µm) Weight: 0.5 kg Measuring face diameter: 6.5 mm Digital readout: yes Special features Ratchet thimble for constant force Digital display with ON/0-, mm/inch, ABS and HOLD Data output: RB 4 Hardened measuring faces Category: Micrometers FAQ What resolution does the micrometer provide? The micrometer delivers a 0.001 mm resolution for fine external measurements, suitable for standard workshop and QA tasks. Is the measuring range suitable for medium-sized components? Yes, the 75–100 mm range covers many shafts, bushings and turned parts common in mechanical production. Does the instrument support data transfer to inspection software? A data output marked RB 4 is provided for numeric transfer where compatible systems are available. How does the ratchet thimble help measurement consistency? The built-in ratchet ensures a repeatable contact pressure, reducing user variation and improving reproducibility of readings with the micrometer. Is the micrometer compliant with recognised standards? The device is built to DIN 863 specifications, aligning it with common industrial practice for mechanical micrometers. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Digital Three-Point Internal Micrometer Carbide Measuring Faces, IP65, Setting Ring, Transport Case - Metav IndustryLine
The combination of IP65 protection, carbide measuring faces and a 0.005 mm declared accuracy ensures reliable shop‑floor performance and long service life; order the instrument directly via Metav Werkzeuge or contact our consultants for specification advice. Digital three-point internal micrometer 87–100 mm by Metav IndustryLine — IP65, carbide faces The Digital three-point internal micrometer 87–100 mm is a compact, shop‑ready instrument for precise internal measurements, especially suited to blind‑hole inspection and fine mechanical tasks. Digital readout with mm/inch and hold function IP65 protection for shop‑floor use Carbide measuring faces for wear resistance Includes setting ring and extension High precision: 0.005 mm accuracy Precise measurement for blind bores and small cavities The three‑point internal micrometer is designed to deliver repeatable results in restricted spaces. With a measuring range of 87–100 mm and declared accuracy of 0.005 mm, the instrument provides a clear advantage where tight tolerances are required. The carbide measuring faces resist wear, preserving measuring geometry during frequent use; combined with the 0.001 mm resolution of the digital display, this makes the device suitable for quality control tasks where micrometre‑level differentiation matters. Data transfer is possible via the RB 6 output, enabling integration into SPC workflows and reducing transcription errors. Robust construction and usability for daily workshop use Built to withstand real production environments, the gauge features IP65 protection, keeping dust and water jets from impairing operation and electronics. The digital module offers ON/PRESET, mm/inch conversion and a HOLD function for straightforward readout of awkward positions. Classified in the micro range (max. 100 mm), the tool balances compactness and stiffness, making it ideal for precision engineering, micro‑assembly and toolroom applications where short‑span stability is essential. Ergonomic handling, plus the included setting ring and extension, speeds up set‑up and repeat measurements on series parts. Practical benefits: setup, traceability and shop integration Delivery includes a protective case for safe transport and the accessories required to work immediately: the setting ring and a dedicated extension for deeper bores. Conformance with DIN 863 underlines workshop suitability and established tolerances for mechanical calipers; the instrument’s three‑point geometry ensures centralised contact in blind holes, preventing tilt‑errors common with two‑point gauges. The instrument’s weight and balance aid controlled measurement strokes while the durable measuring faces and sealed electronics reduce maintenance intervals, improving uptime and measurement consistency. For dependable internal measurement on the shop floor, choose the Metav IndustryLine three‑point internal micrometer 87–100 mm — contact Metav Werkzeuge in Emmerich for technical advice or to discuss integration at info@metav-werkzeuge.com or +49 2822 7131930 Technical Data Article number: M312.242.PN GTIN: 4054469179186 Label: Digital three‑point internal micrometer 87–100 mm Facts Measuring range: 87–100 mm Minimum range: 87 mm Maximum range: 100 mm Resolution: 0.001 mm Accuracy: 0.005 mm Weight: 3.5 kg Protection class: IP65 Standard: DIN 863 Special features Carbide measuring faces Digital display with ON/PRESET, mm/inch, HOLD Data output RB 6 Includes setting ring and extension Suitable for blind‑hole measurement Delivered in protective case Three‑point internal measuring geometry FAQ Is this micrometer suitable for measuring blind bores? Yes. The Digital three‑point internal micrometer 87–100 mm is specifically configured for blind‑hole measurement and its three‑point contact ensures centralised and repeatable readings. What accuracy and resolution can be expected? The instrument offers a declared accuracy of 0.005 mm and a display resolution of 0.001 mm, suitable for demanding workshop and inspection tasks. Can the digital output be connected to quality systems? Yes. The micrometer provides an RB 6 data output for connection to compatible SPC and data‑logging equipment. What does IP65 mean for everyday use? IP65 indicates protection against dust ingress and low‑pressure water jets; the sealed electronics and mechanical design make the device appropriate for typical shop‑floor environments. Are accessories included for deeper bores and set‑up? Delivery includes a setting ring and an extension, allowing quick calibration and measurement of deeper blind bores with the same instrument. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Digital Three-Point Internal Micrometer With Carbide Measuring Faces RB6, For Blind Holes - Metav IndustryLine
Take advantage of digital three-point measurement and carbide measuring faces for reliable blind‑hole checks in the 87–100 mm range; the instrument’s reading of 0.001 mm and accuracy ±0.005 mm support tight tolerances in production. Order the M312.222 directly via Metav Werkzeuge or consult our advisors for application-specific guidance. Digital three-point internal micrometer M312.222 (87–100 mm) – RB6, carbide faces A Digital three-point internal micrometer M312.222 for precise measurement of internal diameters in blind holes, designed for repeatable workshop and inspection use in the 87–100 mm range. Digital readout with mm/inch and hold Carbide measuring faces for wear resistance Accuracy ±0.005 mm for high-precision measurement Precise blind‑hole measurement with repeatable results The three‑point measuring principle provides concentric contact around the bore, yielding more stable readings than single‑edge probes; combined with the RB6 spindle system this reduces eccentricity errors when assessing blind holes. Delivering a resolution of 0.001 mm and an accuracy of ±0.005 mm, the instrument is suitable for quality control tasks where reproducibility matters. The digital readout with ON/OFF/SET and HOLD functions allows quick capture of values and straightforward unit switching between mm/inch, simplifying documentation during inspection rounds. Durable construction for production environments Carbide (HM) measuring faces ensure long service life even under frequent use, maintaining measurement integrity when checking components made from a variety of materials. The robust build contributes to stable contact pressure and repeatable results; this is particularly beneficial when checking series‑produced parts or jigs. The design supports efficient measurement workflows by reducing the need for frequent rechecks and thus contributes to measurable time savings on the shop floor. Easy integration into inspection routines Equipped with a clear digital display and essential control keys, the instrument fits into standard workshop routines without elaborate setup. The instrument is tailored for blind‑hole measurement and marked by practical ergonomics for single‑handed operation where applicable. Traceability is supported through clear numerical output, and the unit’s specifications make it a reliable choice for machinists and inspection staff who need fast, precise readings as part of incoming‑goods checks, in‑process control or final inspection. For application advice and supply from Emmerich, contact Metav Werkzeuge about the Metav IndustryLine M312.222 to ensure the instrument matches the measurement task and workshop workflow. Technical data Article number: M312.222 Brand: Metav IndustryLine GTIN: 4054469169194 Facts Measuring range: 87–100 mm Resolution (reading): 0.001 mm Accuracy: ±0.005 mm Weight: 4.3 kg Special features Carbide (HM) measuring faces RB6 spindle system Digital display with ON/OFF/SET/HOLD/mm/inch Suitable for blind‑hole measurement FAQ What measuring range does the instrument cover? The instrument covers an internal measuring range of 87–100 mm, making it suitable for medium‑sized bores and blind‑hole checks. What level of precision can be expected? The micrometer offers a resolution of 0.001 mm and an accuracy of ±0.005 mm, appropriate for high‑precision workshop inspection tasks. Are the measuring faces wear‑resistant? Yes, the device uses carbide (HM) measuring faces, which provide enhanced wear resistance and long service life under regular use. Is this instrument suitable for blind‑hole measurement? The tool is explicitly designed for blind‑hole measurement and incorporates a three‑point contact system to improve concentricity and repeatability when evaluating such features. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Extension Ø15.5mm for Rod Internal Micrometer Sets, Accessory - Metav IndustryLine
Take advantage of a precise 100 mm reach increase and a dedicated Ø 15.5 mm shank for stable connections; the extension delivers reliable extension of internal measuring capacity and straightforward compatibility with existing micrometer sets. Order the extension directly via Metav Werkzeuge or ask our consultants if needed. Extension 100 mm Ø 15.5 mm for 310.060/61/64 — Accessory for rod internal micrometer sets The Extension 100 mm Ø 15.5 mm for 310.060/61/64 is an accessory designed to extend internal measuring reach for rod-style internal micrometers, enabling measurements in deeper bores and hard-to-reach cavities. 100 mm extension element Ø 15.5 mm precision shank Compatible with 310.060/61/64 sets Lightweight 0.2 kg for easy handling Extend internal reach without losing accuracy The extension offers a simple, mechanical way to increase the measuring range by 100 mm, keeping the original micrometer mechanics intact. By adding this rigid extension the effective reach is increased while preserving the measuring axis alignment, which reduces repositioning and setup time in repetitive checks. The Ø 15.5 mm shank provides a snug fit with the corresponding micrometer spindles, improving concentricity during insertion and lowering the risk of wobble that could affect results. Maintain repeatability for workshop routine checks For production and inspection environments where throughput and consistency matter, a precisely fitting extension helps sustain repeatable internal measurements. The design focuses on a stable connection to the parent instrument so that successive measurements remain comparable; this rational benefit supports faster in-process control and fewer re-measures. The modest mass of 0.2 kg keeps hand‑held handling manageable and avoids introducing extra inertia that might shift readings during contact. Simple handling and long-term workshop value The extension is conceived as a practical workshop aid: it is easy to mount and remove, requires no special tools, and integrates directly with the matching micrometer sets. This convenience translates into lower cycle times for inspection tasks and reduced operator fatigue when accessing deeper features. The accessory’s straightforward function – extend, secure, measure – makes it suitable for maintenance shops, small-series production and quality departments that need a reliable extension without recalibrating the base instrument. Compatibility and trust in supply chain quality Compatibility with sets 310.060, 310.061 and 310.064 is guaranteed by the matched shank diameter and connection geometry, which ensures fast retrofitting into existing tool inventories. Supplied by Metav IndustryLine, the accessory benefits from the vendor’s emphasis on accessible precision: a European distribution hub in Emmerich that acts as a quality filter for the market. This provenance supports procurement decisions where traceable sourcing and dependable availability matter. Contact Metav Werkzeuge today for compatibility confirmation and to secure the M310.061.4 extension as a reliable addition to existing internal micrometer sets Technical data Article number: M310.061.4 GTIN: 4054469118895 Tariff number: 90173000 Category: Accessory (Zubehör) Dimensions / Core data Length: 100 mm Shank diameter: 15.5 mm Mass: 0.2 kg SKU: M310.061.4 Compatibility / Special features Compatible with sets 310.060 / 310.061 / 310.064 Accessory for rod internal micrometer screw sets Lightweight design for handheld and workshop use Intended to extend internal measuring reach FAQ Can the extension be used with any internal micrometer? The extension is designed specifically for compatibility with the 310.060, 310.061 and 310.064 micrometer sets; using the M310.061.4 with other models is only recommended if the connection geometry matches. Does the extension affect measurement accuracy? When fitted to the matching micrometer set the extension maintains axis alignment and repeatability; correct seating of the Ø 15.5 mm shank is essential to preserve measurement integrity. Is the extension suitable for handheld inspection tasks? Yes, the lightweight construction (0.2 kg) of the extension makes it practical for handheld use during routine inspection and maintenance operations. Are any additional parts required to use the extension with the micrometer sets? No additional components are normally needed for the compatible sets; the extension M310.061.4 mounts directly to the matching rod‑internal micrometer assemblies. What material is the extension made from and is it corrosion resistant? Material data is not provided for this item in the specification; for specific material or coating information please refer to the detailed product sheet or contact Metav Werkzeuge. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Extension Ø22 For Rod Inside Micrometer Sets - Metav IndustryLine
Take advantage of the 100 mm extension with a Ø22 mm connector to increase measuring reach while preserving handling and repeatability; compatible with the 310.062 and 310.063 rod micrometer sets and supplied as a compact, lightweight add-on via Metav Werkzeuge for straightforward procurement. M310.063.3 extension 100 mm (Ø22 mm) for internal micrometer rod sets — Metav IndustryLine The M310.063.3 extension increases the measuring reach of rod‑style internal micrometers, enabling reliable measurements in deeper bores and assemblies where the base set lacks sufficient length. 100 mm extension length Ø22 mm connector diameter Compatible with 310.062 and 310.063 sets Extend reach without compromising accuracy The 100 mm extension sleeve provides a pragmatic way to reach deeper internal diameters without replacing the base measuring instrument. By adding a precisely machined extension, the measuring range is extended while preserving the instrument’s original alignment and zero point. The accessory is intended for use with rod‑type internal micrometer sets and connects via a Ø22 mm interface that ensures a repeatable mechanical fit and consistent axial guidance. This approach reduces the need for multiple specialised sets and keeps inventory lean while maintaining measurement integrity. Reliable mechanical interface for repeatable results A compact mass of 0.2 kg gives the extension a balance between stiffness and ease of handling, improving rigidity compared with improvised extensions that can introduce deflection and measurement error. The precise connector geometry supports a stable transfer of the measuring axis, which is crucial for repeatable readings when inspecting bores or stepped internal features. For production environments, this translates into fewer setup adjustments and faster inspection cycles, contributing directly to process efficiency and reduced scrap rates. Seamless workshop integration and supply assurance Designed as a dedicated accessory for rod internal micrometer systems, the extension accepts standard mounting practice for the referenced sets (310.062 / 310.063), ensuring quick interchangeability and minimal retraining. The solution suits repair shops, metrology benches and production control points where occasional reach extension is required without compromising traceability. Delivered through Metav’s European supply chain, the product benefits from a local quality filter and dependable logistics — an assurance that workshop planners value when consolidating suppliers and expecting predictable restocking. Discuss compatibility and application with Metav Werkzeuge in Emmerich to ensure optimal integration of the extension into existing micrometer sets or request tailored configuration advice by phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: M310.063.3 GTIN: 4054469118970 Manufacturer: Metav IndustryLine Customs tariff number: 90173000 Core specifications Extension length: 100 mm Connector diameter: Ø22 mm Weight: 0.2 kg ECLASS: 21019104 ETIM: EC002219 Features Compatible with sets 310.062 and 310.063 Category: Accessory for measuring instruments Story trigger: accessory Thumbnail and product image available FAQ Which micrometer sets are compatible with this extension? The extension is compatible with the 310.062 and 310.063 rod internal micrometer sets and fits the Ø22 mm connector interface used on those assemblies. What are the exact dimensions of the extension? The accessory provides a 100 mm extension length with a Ø22 mm connector and a total mass of 0.2 kg. Will the extension affect measurement repeatability? When mounted correctly on the corresponding rod micrometer set, the extension maintains axial alignment and supports repeatable measurements thanks to its precise connector geometry. Is the extension suitable for production and bench inspections? Yes; the extension is intended for workshop and production metrology tasks where additional reach is required without replacing the base instrument. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Micrometer Caliper With Four Interchangeable Carbide Faces, Ratchet Spindle, Matte Chrome Drum, Supplied In Case - Metav IndustryLine
Combine high reproducibility from the ratchet stop, long-term wear resistance of the carbide measuring faces and fine 0.01 mm reading accuracy for consistent inspection workflows; the set is supplied in a protective case and includes interchangeable anvils for flexible part contact. Order the outside micrometer directly via (Metav Werkzeuge) or ask our consultants if needed. Outside micrometer 0–100 mm — Metav IndustryLine (4 interchangeable anvils, carbide faces) Outside micrometer 0–100 mm for workshop and quality-control tasks, fitted with a ratchet spindle and four interchangeable anvils to measure a wide variety of external dimensions accurately Carbide measuring faces for long wear life Ratchet stop for consistent measuring force Four interchangeable anvils for varied parts Matt chrome-plated thimble and robust frame Reliable accuracy for repeatable quality control The instrument delivers a measuring range of 0–100 mm with an analogue reading to 0.01 mm and an evaluated accuracy of ±0.009 mm, making it suitable for standard workshop verification and fine inspection tasks. The ratchet stop ensures a constant measuring force, reducing operator-induced variation on each measurement, while the 0.5 mm spindle pitch provides smooth, predictable advances per revolution. These technical characteristics result in dependable results when documenting part dimensions or comparing batches against drawing tolerances. Robust design that reduces maintenance and downtime Built for frequent use, the micrometer features carbide measuring faces that resist wear and preserve measuring geometry over time. The matt chrome-plated thimble improves legibility and limits glare in workshop lighting, while the supplied protective case keeps the instrument safe during transport and storage. The set of four interchangeable anvils allows contact with differing part geometries without improvised adapters, shortening setup time and enhancing process efficiency for repetitive checks. Practical calibration and workshop integration Setting gauges at 25 / 50 / 75 mm are included as reference points for quick verification to factory tolerance; the instrument is supplied to factory standard and the analogue mechanism permits intuitive readings without electronics. Its stabile frame construction and a weight of approximately 1.1 kg give tactile feedback and a balanced feel during measurement sequences. The model M304.028 integrates straightforwardly into routine inspection protocols and is suited to machining shops, maintenance departments and small-series quality checks thanks to its blend of resilience and measuring fidelity. For procurement or technical clarification regarding the Metav IndustryLine outside micrometer, contact Metav Werkzeuge for ordering and application support Technical data Article number: M304.028 GTIN: 4054469115856 Brand: Metav IndustryLine Category: Micrometers / Measuring instruments Numbers / Core technical data Measuring range: 0–100 mm Resolution / reading: 0.01 mm Accuracy: ±0.009 mm Spindle pitch: 0.5 mm Weight: 1.1 kg Special features / Versions Carbide measuring faces Ratchet stop for consistent measuring force Four interchangeable anvils Matt chrome-plated thimble Analogue instrument (mechanical) Factory standard (Werksnorm) Delivered in protective case FAQ What measuring range does the micrometer cover? The outside micrometer covers a measuring range of 0–100 mm and is supplied as article M304.028 from Metav IndustryLine. How fine is the reading and how accurate are measurements? Readings are at 0.01 mm resolution with an evaluated accuracy of ±0.009 mm, suitable for routine inspection and workshop checks. Are the measuring faces resistant to wear? Yes, the tool is fitted with carbide measuring faces, which extend service life and maintain contact geometry under repeated use. Does the set include accessories for verification? Reference setting gauges at 25 / 50 / 75 mm are provided for quick verification to factory tolerances. Is the instrument supplied ready for transport and storage? The micrometer is delivered in a protective case to safeguard the instrument during transport and storage. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Micrometer Holder Foldable, Adjustable Angle, 750g - Metav IndustryLine
Take advantage of a compact, foldable design combined with an adjustable tilt angle for reliable, repeatable positioning of micrometers up to 100 mm; the holder streamlines setup and reduces handling error in routine inspection tasks. Order the micrometer holder directly via Metav Werkzeuge or ask the consultants for application advice. Micrometer holder M304.005 — Foldable holder with adjustable tilt for micrometers up to 100 mm (Metav IndustryLine) Micrometer holder M304.005 provides secure, hands-free positioning for bench and workshop measurements, supporting standard frame micrometers and offering an adjustable tilt for better access and alignment Foldable design for compact storage Adjustable tilt for ergonomic alignment Holds micrometers up to 100 mm Stable weighted base for steady measurements Engineered for repeatable, hands-free measurement The holder is designed to deliver consistent repeatability by fixing the measuring instrument in a defined position, which reduces variability from manual handling. With a foldable structure and a mechanically simple tilt adjustment, the accessory allows quick set-up and stable clamping of standard micrometers. This improves throughput in inspection routines and supports quality control by making individual readings more comparable between operators and over time. Key mechanical interactions are minimised so focus can remain on the measured part rather than instrument orientation. Improved ergonomics and faster inspection cycles An adjustable tilt angle gives better visual and physical access to the spindle and thimble, which eases reading and operation during repetitive tasks. The holder’s layout supports bench-based workflows and small-batch production, enabling an operator to position the micrometer, align the part and record results without constantly reorienting the instrument. The result is a measurable gain in convenience and process consistency, helping to reduce fatigue during longer measuring sessions and to speed up typical inspection steps. Practical compatibility for workshop use Built as an accessory for measuring instruments, the unit accepts micrometers up to 100 mm and is suitable for use alongside standard inspection benches and fixtures. The simple mechanical design requires no power supply and integrates easily into existing measuring stations. Because the accessory is foldable, it is straightforward to store or transport between workstations when the layout of the shop floor changes. The holder is particularly useful where repeatable orientation and stable support of the micrometer are required for series checks or assembly-level verifications. Choose the Metav IndustryLine micrometer holder M304.005 to secure micrometers for stable, repeatable measurements — contact Metav Werkzeuge for detailed application guidance or to confirm suitability for a specific measuring task: info@metav-werkzeuge.com / +49 2822 7131930 Technical data Article number: M304.005 GTIN: 4054469115832 ECLASS: 21029090 Facts Compatible micrometer size: up to 100 mm Customs tariff number: 90173000 Category: Messgeräte > Zubehör Special features Foldable design Adjustable tilt angle Suitable for micrometers up to 100 mm Accessory for measuring instruments SKU: M304.005 FAQ Is the holder suitable for all micrometers? The holder is designed for standard frame micrometers with measuring ranges up to 100 mm; the M304.005 secures common bench and workshop instruments within that range. Can the angle be adjusted while measuring? Yes, the adjustable tilt angle on the M304.005 permits fine alignment before securing the micrometer, improving access and reducing the need to reorient the workpiece. Does the holder need a fixed mounting on a bench? The accessory is freestanding and foldable for flexible placement on inspection benches; it can be repositioned as required for different measuring tasks. Is electrical power required for operation? No power supply is necessary; the holder is a purely mechanical accessory intended to stabilise and orient micrometers. What improvements in measurement practice does this accessory provide? By fixing the instrument in a repeatable orientation and improving ergonomic access, the holder reduces handling variability and speeds up routine checks with micrometers up to 100 mm. Metav IndustryLine: Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Micrometer Holder Swivelling With Adjustable Tilt, 1.5 kg Capacity - Metav IndustryLine
Data inconsistency detected: the compatible micrometer range is given as both up to 100 mm and up to 200 mm, and the weight/load is listed as both 1.5 kg and 0.9 kg. These discrepancies in the specifications create confusion and must be addressed to ensure clarity and accuracy. Please resolve these conflicting details regarding the micrometer range and weight/load capacity before a product description can be generated. Accurate and consistent specifications are essential for creating a reliable product description that meets customer expectations and avoids potential misunderstandings. Kindly review and update the conflicting data to proceed with the description creation process.
100mm Micrometer Set 1 µm Resolution, ISO 17025 Calibrated, Ratchet Stop - Microtech Metrology
Take advantage of the combination of laboratory-grade accuracy, ISO 17025 traceability and ready-to-use delivery for reliable inspection routines; order the set directly via Metav Werkzeuge or consult our specialists for integration advice. MICRON OUTSIDE Certi Met micrometer set — 1 µm resolution, ISO 17025 calibrated (Microtech Metrology) The MICRON OUTSIDE Certi Met micrometer set is a precision outside‑measurement toolset intended for metrology labs and precision workshops, offering sub‑micron readout and documented traceability. 1 µm resolution, high-precision reading ISO 17025 calibration certificate included Ratchet thimble for consistent measuring force Measure with laboratory-grade repeatability The set delivers 1 µm resolution and a claimed high accuracy of ±2 µm, which reduces measurement uncertainty in routine inspections. Supplied with an ISO 17025 calibration certificate, the instruments arrive ready for traceable quality control and can be integrated directly into documented measurement processes. The mechanical friction thimble design and clear analog readout support fast, repeatable readings while keeping handling straightforward for trained staff. Practical design for consistent results A built-in ratchet thimble ensures uniform measuring force, limiting operator‑induced variation and improving reproducibility across batches. The delivery includes a set of 4 micrometers and a setting rod plus a calibration protocol, making the kit suitable for sequential gauging across the 0–100 mm range without interruption. The solid micrometer head construction and tactile thimble reduce slippage during delicate adjustments, so fewer rechecks are necessary in daily inspection work. Fast adoption within quality workflows Because the instruments are supplied calibrated to ISO 17025, documentation for audits and process validation is already available, shortening preparation time for quality audits. The analog readout combined with micron‑level resolution supports both quick shop‑floor checks and formal laboratory tasks, helping to streamline non-conformance detection and corrective action. The compact design of each gauge in the set favours efficient storage and quick tool changes in production environments. Where this micrometer set adds most value The kit is designed for outside measurements of small to medium components across precision engineering, toolmaking and laboratory contexts. Its calibrated status and repeatable measuring force make it particularly suitable where traceability and reduced measurement uncertainty are priorities. The combination of robust mechanics and certified accuracy supports both routine dimensional checks and documented quality assurance tasks. For fully traceable precision from Microtech Metrology, request the MICRON OUTSIDE Certi Met micrometer set via Metav Werkzeuge or contact our metrology team at info@metav-werkzeuge.com / +49 2822 7131930 for specification matching and delivery options Technical Data Article number: 110110110 GTIN: 4061905456886 Manufacturer: Microtech Metrology Set: 4 pieces Delivery: Calibration protocol, setting rod Facts Measuring range: 0–100 mm Resolution: 0.001 mm Accuracy: ±2 µm (stated) Calibration: ISO 17025 certificate included Readout type: analog / mechanical Special features Ratchet thimble for consistent measuring force Friction thimble micrometer head High accuracy up to ±2 µm Set out of 4 micrometers FAQ What measuring range is covered by this micrometer set? The set covers the full 0–100 mm range, supplied as four sequential micrometers for continuous outside measurements. Is the micrometer set delivered calibrated? Yes, the MICRON OUTSIDE Certi Met micrometer set is delivered with an ISO 17025 calibration certificate and a calibration protocol. What resolution and accuracy can be expected? The instruments offer 1 µm resolution with a stated accuracy of ±2 µm, suitable for high‑precision inspection tasks. Which features help reduce operator error? The ratchet thimble and friction thimble design provide consistent measuring force, improving reproducibility across operators and shifts. Is this set suitable for laboratory and shop‑floor use? Yes, the combination of micron resolution, robust mechanics and traceable calibration makes the set appropriate for both laboratory procedures and precision workshop checks. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
100mm Micrometer With 20mm Anvil Faces, Digital Display, ISO 17025 Calibration Certificate - Microtech Metrology
High-precision measurement with 0.005 mm accuracy and 0.001 mm resolution ensures reproducible results for fine mechanical and laboratory work; the instrument is fitted with 20 mm disc faces and a non-rotating spindle for gentle, repeatable contact and is delivered fully calibrated to ISO 17025 with a calibration certificate. Order the Microtech Metrology digital micrometer via Metav Werkzeuge or contact our consultants for specification support. Digital micrometer by Microtech Metrology — 75–100 mm, 0.005 mm accuracy The Digital micrometer provides precise thickness and external measurements for fine mechanical, watchmaking and laboratory applications in the 75–100 mm measuring range. High accuracy 0.005 mm 0.001 mm reading resolution 20 mm disc measuring faces Delivered calibrated to ISO 17025 Precision and performance for fine work The digital micrometer combines a fine resolution of 0.001 mm with an overall accuracy of 0.005 mm, delivering measurement stability that supports traceable quality control. The instrument’s non-rotating spindle prevents rotation-induced run-out while the 20 mm disc faces distribute contact force evenly, reducing local deformation on thin or delicate parts. These features translate into consistent, reproducible results when comparing batches or verifying incoming components, and the digital readout minimises reading errors common to mechanical scales. Compact range tailored to delicate components Classified in the micro range (measuring range 75–100 mm), this micrometer is optimised for compact yet precise tasks where stiffness and handling balance is critical. The shorter frame improves rigidity and makes the instrument easy to position in confined setups, which is helpful for watchmakers, small-part assembly and precision laboratory measurements. The disc-shaped anvils are particularly suitable for measuring flat or slightly rounded surfaces without marking, so delicate samples remain undamaged while measurement repeatability is maintained. Digital ergonomics and assured calibration The instrument features a clear digital display with 0/MODE, SET, UNIT and HOLD keys for straightforward zeroing, function selection, unit switching and locking of readings. These controls support a fast measurement routine and simplify data capture during inspection sequences. Delivered fully calibrated to ISO 17025, the micrometer arrives with a calibration certificate, providing documented traceability for in-house quality systems and audit requirements. The combination of ergonomic controls and certified calibration supports efficient, auditable workflows on the shop floor. Contact Metav Werkzeuge to request detailed specifications or to reserve the Microtech Metrology digital micrometer for precision measurement tasks — local stock and expert advice available from Emmerich. Technical Data SKU: 110781001 GTIN: 4061905457999 Manufacturer: Microtech Metrology Facts Accuracy: 0.005 mm Resolution: 0.001 mm Measuring range: 75–100 mm Measuring face diameter: 20 mm Special features Digital display with 0/MODE, SET, UNIT and HOLD buttons Non-rotating spindle Delivered calibrated to ISO 17025 with calibration certificate Category: Micrometer FAQ Is the instrument delivered calibrated? Yes. The Microtech Metrology digital micrometer (SKU 110781001) is delivered fully calibrated to ISO 17025 and includes a calibration certificate. What accuracy and resolution can be expected? The device provides an accuracy of 0.005 mm and a resolution of 0.001 mm, suitable for fine mechanical and laboratory checks. What is the measuring range and which tasks is it suited for? The measuring range is 75–100 mm, making it ideal for compact components, precision workshop tasks, watchmaking and small-part inspection. Which measuring faces are fitted and why are they used? Equipped with 20 mm disc measuring faces, the micrometer offers gentle contact and even force distribution; the spindle is non-rotating to improve repeatability. How are readings and functions handled on the display? Readings are shown on a digital display controlled by 0/MODE, SET, UNIT and HOLD keys for zeroing, mode selection, unit change and measurement hold. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
100mm Micrometer With Pointed Measuring Faces, Colour Touchscreen, IP65, ISO 17025 - Microtech Metrology
Benefit from the combination of reliable wireless data transfer, robust IP65 protection and an ISO 17025 calibration certificate to secure traceable, production-ready measurements; order the micrometer directly via Metav Werkzeuge or contact our consultants for application guidance. Microtech micrometer — 75–100 mm, 2.4″ colour touchscreen A Microtech micrometer for high-precision external measurement tasks in fine mechanical and industrial metrology Wireless and USB data transfer ISO 17025 calibration certificate included IP65 CNC-machined aluminium housing 2.4" colour touchscreen with 2,000-value memory Laboratory-grade accuracy and certified traceability This micrometer combines exceptional measuring resolution with formal traceability: the instrument reads to 0.0001 mm and achieves an accuracy of 0.004 mm, values that support repeatable quality control and fine-tolerance assembly. Supplied with an ISO 17025 calibration certificate (Ilac MRA), the device meets accredited laboratory standards so measurement results can be accepted across suppliers and internal audit trails. The certified calibration reduces uncertainty in documented inspection records and supports process-capability analysis. Integrated data flow for modern production control Connectivity is designed for efficient data capture: the unit offers wireless and USB transfer modes, compatibility with Windows/Android/iOS/MacOS apps and a 2000-value memory with folder and statistics management. The built-in DataMet POINT functionality and the MICS system enable online graphs, Go/NoGo checks, Max/Min logging, formula and temperature correction—features that simplify downstream evaluation and SPC routines. Optional Modbus RTU (RS-485) allows direct industrial network integration for automated logging and process feedback. Engineered for workshop durability and everyday usability Mechanical design focuses on robustness and handling: a CNC-machined aluminium housing with IP65 protection withstands workshop dust and coolant splashes while keeping electronics safe. The instrument uses pointed measuring faces, a rotating spindle and a friction ratchet for consistent measuring force—advantages when accessing small grooves or stepped features. A bright 2.4" colour touchscreen provides intuitive menus, and the housing and interface choices reduce operator error and speed up inspection cycles. The 75–100 mm measuring range places this instrument in the micro class for fine mechanical work, making it suitable for precision components, gauges and delicate assemblies. Contact Metav Werkzeuge in Emmerich for tailored application advice and to secure this Microtech micrometer with ISO 17025 calibration; eMail: info@metav-werkzeuge.com — Tel: +49 2822 7131930 Technical data Article number: 110451008 GTIN: 4061905040832 Manufacturer: Microtech Metrology Facts Measuring range: 75–100 mm Resolution: 0.0001 mm Accuracy: 0.004 mm Display: 2.4" colour touchscreen Memory: 2000 values Special features Digital instrument with MICS DataMet POINT system Data output: Wireless + USB (four transfer modes incl. HID) Optional Modbus RTU (RS-485) for industrial connection CNC-machined aluminium housing IP65 protection class Calibration certificate included (ISO 17025, Ilac MRA) Pointed measuring faces Friction ratchet and rotating spindle FAQ What measuring range does the micrometer cover? The Microtech micrometer covers 75–100 mm, a micro-class range suited to fine mechanical components and tight-tolerance external measurements. Is an accredited calibration delivered with the device? Yes, the micrometer is delivered with a calibration certificate issued under ISO 17025 (Ilac MRA), ensuring traceable, laboratory-grade results. How can measurement data be exported to a PC or network? Data can be transferred wirelessly to the MDS app (Windows/Android/iOS/MacOS), via Wireless HID, Wireless HID+Mac or USB HID; an optional Modbus RTU interface provides industrial RS-485 connectivity. What level of protection does the housing provide in a workshop environment? The CNC-machined aluminium housing is rated IP65, protecting electronics from dust ingress and low-pressure water jets commonly encountered on the shop floor. Which article number should be quoted when ordering or requesting documentation? Please quote article number 110451008 when enquiring about this Microtech micrometer or requesting the ISO 17025 certificate. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
100mm Outside Micrometer Ratchet Stop, Calibration Certificate ISO17025, Set of 4 - Microtech Metrology
Take advantage of precise, traceable measurements combined with consistent measuring force and workshop-ready robustness: the set provides ISO 17025 calibration, a ratchet-stop spindle and 0.01 mm resolution across the 0–100 mm range. Order the calibrated micrometer set via Metav Werkzeuge or consult our specialists for application advice. Outside Micrometer Set by Microtech Metrology — ISO 17025 calibrated, ratchet stop A compact, calibrated outside micrometer set Outside Micrometer Set designed for repeatable external measurements across the 0–100 mm range in workshop and inspection environments. ISO 17025 calibration certificate included Ratchet-stop spindle for repeatable force 0.01 mm resolution analogue thimble Set covering the 0–100 mm measuring range Traceable precision for critical dimensions High-resolution analogue micrometers deliver measurable improvements in process control and first-pass quality. With a 0.01 mm thimble graduation and a supplied calibration certificate issued to ISO 17025, the instruments provide documented accuracy suitable for incoming inspection and quality assurance. The built-in ratchet stop reduces variation from operator-applied pressure, which helps to lower measurement scatter and improve reproducibility during batch inspections. These features translate directly into fewer reworks and more predictable production outcomes. Consistent handling and repeatability in every measurement The four-piece composition of the set covers the full 0–100 mm span while keeping each instrument compact and easy to handle. An anvil Ø6.5 mm provides a stable seating area for shafts and bars, reducing local deformation on small-diameter parts. The analogue design with clear thimble graduations is robust against shop-floor conditions and allows quick verification without reliance on electronics. As a result, routine measuring tasks are faster to perform and less prone to interruption, increasing throughput in small-batch and repair work. Practical technique that reduces user error The ratchet-stop spindle enforces a consistent contact force, which is particularly valuable where many operators share the same instruments. The analogue thimble readout at 0.01 mm resolution gives an immediate, intuitive result while supporting traceable documentation when paired with the supplied calibration certificate. For operators accustomed to micrometre technique, the combination of tactile feedback and precise graduation streamlines measurement routines and lowers the learning curve for new staff. Suitable applications and who benefits Mechanical workshops, maintenance departments and production inspection teams benefit most from a calibrated micrometer set that balances accuracy with durability. Typical uses include checking shaft diameters, bearing journals, turned parts and assembled components where external dimensions are critical. The four-piece set format keeps workbenches tidy and ensures the right tool is at hand for small to medium components, while the ISO 17025 traceability supports formal quality systems and audits. For calibrated precision and traceable results, contact Metav Werkzeuge to secure the Microtech Metrology outside micrometer set and request the ISO 17025 calibration certificate — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: 110110111 GTIN: 4061905458910 Manufacturer: Microtech Metrology Numbers / Core technical data Measuring range: set 0–100 mm Resolution: 0.01 mm Pieces per set: 4 Anvil diameter: Ø6.5 mm Analogue reading Ratchet-stop spindle: yes Calibration: ISO 17025 certificate included Special features Four-piece outside micrometer set Ratchet-stop for reproducible contact force Analogue thimble with 0.01 mm graduation Supplied with ISO 17025 calibration certificate Suitable for workshop and inspection use FAQ Is the micrometer set supplied calibrated to an accredited standard? Yes. The Outside Micrometer Set from Microtech Metrology is delivered fully calibrated to ISO 17025 and includes a calibration certificate; SKU 110110111. What resolution and reading accuracy does the set provide? The micrometers feature an analogue thimble with 0.01 mm graduation; combined with proper technique and the included calibration, this supports consistent readings for standard workshop inspection tasks. How does the ratchet-stop spindle improve measurements? The ratchet-stop enforces a repeatable contact force, reducing measurement variation between operators and improving reproducibility across repeated checks. Which measuring range is covered by the set? The four-piece set covers the 0–100 mm measuring span, providing continuous coverage for small to medium external dimensions. What typical tasks are these micrometers used for? Common applications include measuring shafts, journals and turned parts in maintenance, production and quality control environments, where external dimension accuracy is essential. Manufacturer / Responsible: Microtech, Nizhneyurkovska str., 45a, 04080 Kyiv, Ukraine, tool@microtech.tools
100mm Outside Micrometer Set 4-Piece Friction Thimble Matt Chrome Finish In Case - Metav IndustryLine
Take advantage of precise, repeatable external measurement with a satin chrome‑plated measuring drum and an integrated friction ratchet for consistent measuring force; order the set directly via Metav Werkzeuge or consult the specialists if further technical advice is required. M304.240 Outside Micrometer Set — 0–100 mm, 4‑piece, friction ratchet | Metav IndustryLine A robust M304.240 outside micrometer set designed for accurate external measurements across 0–100 mm, supplied as a four‑piece kit in a protective cassette Friction ratchet for repeatable measuring force 0.01 mm graduation for precise readings Satin chrome‑plated measuring drum for durability Comprehensive 4‑piece set with setting standards Precision that reduces rework and inspection time The set is an analog micrometer family that delivers a 0.01 mm reading by combining a spindle pitch 0.5 mm with fine thimble graduations, which equals 0.01 mm per division. This mechanical arrangement provides a direct, tactile measurement method that is easy to verify and calibrate. Conformity with DIN 863 ensures the instruments meet recognised workshop standards, making them suitable for routine dimensional checks where traceable, repeatable readings are required. The clear graduations and satin finish on the measuring drum reduce parallax and glare, aiding consistent interpretation of results. Consistent measuring force for reliable results A built‑in friction ratchet controls the applied measuring pressure and reduces operator‑related variability during the final approach. This feature is particularly valuable when multiple operators inspect identical parts or when short‑term repeatability is critical to maintain process capability. The micrometer spindle uses a conventional 6.5 mm diameter design and the measured mechanical arrangement is optimised for stable axial movement; as a result, measurements show lower scatter under normal workshop handling. The analogue mechanism also allows immediate verification and maintenance without electronic dependencies. Practical kit layout that supports workshop efficiency Supplied as a 4‑piece set with setting standards at 25 / 50 / 75 mm, the instruments cover the common measurement intervals used in production and inspection. Each micrometer is housed in a purpose‑made cassette for organised storage and safe transport between workstations. The satin chrome‑plated measuring drum resists wear and provides a tactile, low‑reflection surface that keeps scales legible over time. Together, the modular design and exchangeable sizes reduce tool changes and speed up inspection cycles on the shop floor. Built for everyday workshop use and straightforward maintenance As an analog solution, the instruments are mechanically simple to service; routine checks include cleaning the spindle faces, verifying the setting standards and ensuring the ratchet mechanism remains free of debris. The DIN 863 reference and the robust surface plating make these micrometers a practical choice for environment‑tolerant inspection points in machine shops and maintenance departments. The set format also streamlines inventory control and allows teams to match the right micrometer to the task without delay. For supply and specialist advice on the Metav IndustryLine M304.240 outside micrometer set, contact Metav Werkzeuge in Emmerich to arrange procurement and technical clarification Technical data Article number: M304.240 GTIN: 4054469116532 eClass: 21170328 ETIM: EC003590 Customs tariff number: 90173000 Facts Measuring range: 0–100 mm Resolution: 0.01 mm Spindle pitch: 0.5 mm Measuring spindle diameter: 6.5 mm Pieces per set: 4 Setting standards included: 25 / 50 / 75 mm Special features Friction ratchet for repeatable measuring force Satin chrome‑plated measuring drum Conforms to DIN 863 Analog measurement principle Delivered in a protective cassette FAQ What measuring range does the set cover? The set covers an external measuring range from 0 to 100 mm with four instruments that step through the standard intervals. What resolution and graduations are provided? Each micrometer offers a 0.01 mm graduation, achieved with a 0.5 mm spindle pitch combined with fine thimble divisions. How is consistent measuring force achieved? A built‑in friction ratchet provides a uniform end‑stop torque to reduce variation caused by differing operator pressure. Is the set suitable for everyday workshop inspection? Yes, the kit conforms to DIN 863 and is designed for routine dimensional checks in production and maintenance environments. What does the cassette provide? The cassette organises the four instruments and their setting standards, protecting them from impact and making storage and transport straightforward. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Set Of Outside Micrometers With Setting Gauge, Ratchet, Powder-Coated Frame - Metav IndustryLine
Take advantage of a robust workshop set that combines repeatable measuring force, a clear 0.01 mm reading and quick verification with supplied setting gauges; the result is efficient in-process inspection and lower rework rates. Order the set directly via Metav Werkzeuge or contact the consultants for specification support. Metav IndustryLine Micrometer set M304.420 – 0–100 mm, ratchet stop The Micrometer set M304.420 is a four-piece outside micrometer set for workshop and inspection use, covering 0–100 mm and supplied with setting gauges for rapid verification. Four-piece 0–100 mm set Ratchet stop for consistent measuring force Conforms to DIN 863 Blue powder‑coated frame and matt‑chrome drum Repeatable measurements for production control The four-piece set covers 0–100 mm in short, easy-to-handle increments, which speeds routine checks and reduces the need for multiple single instruments. The mechanical design includes a ratchet stop, which ensures a consistent measuring pressure and reduces operator-induced variation; this leads directly to reproducible results on batch inspections. With an analogue reading resolution of 0.01 mm, the set matches standard workshop tolerances and aligns with the DIN 863 specification for outside micrometers, offering a reliable balance between precision and everyday usability. A finish built to withstand the shop floor The frame is blue powder‑coated, providing corrosion resistance and a durable surface that tolerates regular handling; the measuring drum is matt‑chrome, which improves contrast for the engraved scale and reduces glare during reading. The spindle diameter of 6.5 mm contributes to axial stiffness and steadiness when measuring, while the overall set weight of approximately 2.1 kg conveys a robust construction without sacrificing portability. Supplied setting gauges (25 / 50 / 75 mm) simplify zero checks and speed up setup so that measuring time is reduced and throughput improves. Workflow advantages and supplier confidence Supplied as a complete four-piece set with ergonomic ratchet control and clear scales, the micrometers are suited for in-process control, incoming inspection or maintenance tasks where rapid, repeatable checks are required. The mechanical construction, together with the 0.5 mm spindle pitch, supports fine adjustment and tactile feedback for careful measurement. Procurement through Metav IndustryLine brings the practical advantage of a European quality filter and reliable logistics from Emmerich, backed by a broad product range for centralised tool sourcing and consistent availability. Contact Metav Werkzeuge in Emmerich for tailored advice on the M304.420 micrometer set and to arrange delivery: +49 2822 7131930 or info@metav-werkzeuge.com Technical data Article number: M304.420 GTIN: 4054469116990 Category: Messschrauben / Micrometers Facts Measuring range: 0–100 mm Resolution / reading: 0.01 mm Spindle diameter: 6.5 mm Spindle pitch: 0.5 mm Weight: 2.1 kg Tariff number: 90173000 Features Frame: blue powder‑coated Measuring drum: matt‑chrome Ratchet stop Supplied with setting gauges: 25 / 50 / 75 mm Set of 4 micrometers Conforms to DIN 863 Analogue reading FAQ What measuring range does the set cover? The M304.420 micrometer set covers a total measuring range of 0–100 mm across four instruments. What is the smallest increment readable on the scale? The micrometers provide an analogue reading resolution of 0.01 mm for standard workshop tolerances. Are setting gauges included for verification and adjustment? Yes, the set is supplied with setting gauges of 25, 50 and 75 mm to facilitate quick checks and adjustment. Does the set meet any recognised standards? The instruments conform to DIN 863, which governs outside micrometer dimensions and performance. How does the ratchet stop benefit measurements? The integrated ratchet stop delivers a consistent measuring force, reducing operator variation and improving repeatability of results. Manufacturer / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
Precision micrometers built for repeatable accuracy
Micrometers—also referred to as micrometer screw gauges or micrometer callipers—are compact, robust instruments for fast, highly accurate length measurement of small to medium workpieces. Designed for routine use on the shop floor, these tools combine mechanical reliability with options for digital data capture, making them indispensable where repeatable tolerances matter.
How micrometers work and where they belong in production
Micrometers operate on a finely threaded spindle that brings two measuring faces into alignment with the workpiece; many designs follow the Abbe comparator principle so that the measuring axis and scale are collinear, reducing tilting errors. Typical outside micrometers (bühlermessschrauben) provide readings down to 1/1000 mm (0.001 mm) in analogue form; internal micrometers and specialised two- or three-point gauges enable accurate diameter and bore measurements, while depth micrometers cover depths from 0–300 mm. Hardened carbide (HM) measuring faces are standard to prevent wear and maintain accuracy over time. Digital variants offer easy reading, unit switching (mm/inch) and data output via USB, RS interface or Bluetooth; advanced models with an integrated minicomputer support Go/NoGo checks, temperature compensation and wireless transmission up to 50 m.
Practical benefits that improve shop‑floor performance
- Reduced rework and higher first-pass yield thanks to repeatable accuracy and carbide-tipped measuring faces.
- Faster, safer measurement cycles by using the ratchet/coupling to limit measuring force to 5 N to 10 N, protecting both part and instrument.
- Flexible inspection workflows with analogue, digital and minicomputer options, including wireless data transfer and mm/inch toggle.
- Versatile coverage with outside, internal, depth and built-in micrometers offering measuring ranges from a few millimetres up to 300 mm and resolution down to 2 µm (internal) or 0.003 mm (standard depth micrometers).
- Durable operation in workshop environments: mechanical models resist dust and moisture, while digital versions are available with IP54 protection.
Metav — a precision partner you can rely on
Metav combines decades of technical expertise with a broad, quality-filtered product range from its Emmerich hub. Over 48,000 customers trust Metav’s offer of more than 250,000 products, which simplifies procurement and secures reliable supply for industry, trade and specialist retailers. For buyers seeking micrometers with consistent performance and traceable data capture, Metav’s selection and technical support make it a practical, long-term choice.
In short
Micrometers provide robust, highly repeatable measurement for external, internal and depth applications, available in analogue, digital and minicomputer formats to match precision requirements and data‑management needs.
FAQ
How precise are micrometers for internal measurements?
Internal micrometers in the micrometers category can achieve accuracies around 2 µm when correctly used; digital and minicomputer models improve readout convenience and data integration for traceable inspection results.
When is a digital micrometer preferable to an analogue one?
Choose a digital micrometer when easy readout, unit conversion (mm/inch), or data transmission is required. Digital models with IP54 rating also offer dust and splash protection, while analogue micrometers remain the most robust option in harsh environments.
What measuring force should be used to ensure consistent results?
The recommended measuring force for micrometers is 5 N to 10 N. Use the ratchet or friction thimble to apply this consistent force and rely on the insulating sleeve to minimise heat transfer from the hand.
Can depth micrometers measure small bores and tight features?
Yes. Depth micrometers use a fine needle or flat measuring face and, with suitable extensions, cover narrow or deep features; standard depth micrometers typically span 0–300 mm with accuracies near 0.003 mm, while specialised digital systems offer even higher resolution.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com