Modular screw-in cutters for adaptable deep machining
Screw-in cutters are modular milling tools designed to be screwed into extensions or toolholders to adjust overhang for deep or recessed machining and to make tool systems more economical by allowing only the front milling head to be replaced; they are indispensable in tool and mould making for such reasons. Where machining requires coolant delivered through the tool, internal cooling provides continuous, directed supply through channels to the cutting edges, whereas designs without internal cooling rely on external nozzles and suit only very shallow, easily accessible operations. For deep cavities and long extensions, the combination of long extensions and internal coolant ensures high flush pressure to evacuate chips against gravity, reduce thermal load and prevent chip clogging and vibration. Key advantages include improved tool longevity, higher process reliability and easier tool maintenance, with the primary use being precision metalworking and cavity finishing.
100mm Extension For Screw-In Milling Cutter 16mm Shank M8 Thread - Teknik Makina
Take advantage of the combination of extended reach, a secure M8 screw-in connection and compact weight to improve milling accessibility without compromising rigidity; order the extension directly via Metav Werkzeuge or consult our specialists for fit verification. Extension for Screw-in Cutters VT503TM — M8 thread, 100 mm overall length A Extension for Screw-in Cutters designed to extend tool reach and adapt screw-in milling cutters for operations requiring a 16 mm shank interface M8 thread for secure screw-in connection 100 mm overall length for extended reach 16 mm shank diameter compatible with standard holders 30 mm conical seat for precise centring Greater reach with maintained rigidity This extension provides an efficient way to access recessed features without sacrificing tool stability. The combination of a 100 mm overall length with a 16 mm shank preserves the balance between reach and lateral rigidity, reducing chatter in shallow pockets. The M8 thread and the 30 mm conical seat ensure a secure fit with screw-in cutters, which keeps the cutting edge concentric and repeatable across tool changes. The design is aimed at workshop environments where precise positioning and consistent cutting results are required. Compatibility that speeds up workflows Designed for straightforward integration into standard tool holdings, the adapter shortens setup time and supports faster changeovers. The 14 mm opening for the screw-in cutter and the 16 mm shank diameter match common holder specifications, enabling compatibility with a wide range of screw-in milling cutters. The unit’s lightweight construction (approx. 0.15 kg) minimises added inertia, facilitating quick tool changes while maintaining the spindle’s responsiveness. For production runs where uptime matters, this extension contributes to measurable efficiency gains. Precision alignment for reliable machining Accurate machining depends on consistent alignment; the extended conical engagement and secure M8 thread help to maintain concentricity between tool and spindle under load. That stability translates into cleaner surface finishes and reduced rework for components milled in confined areas. The component is suitable for use in both manual and CNC milling contexts where a screw-in cutter requires additional reach. For project planning, refer to the technical data below to verify dimensions and intended applications before integration into a machine setup. Choose Teknik Makina’s VT503TM extension for reliable extra reach — contact Metav Werkzeuge for purchase and technical advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: VT503TM Manufacturer: Teknik Makina Designation: Extension for screw-in cutters Facts Overall length: 100 mm Shank diameter: 16 mm Cutter opening diameter: 14 mm Conical seat length: 30 mm Weight: 0.15 kg Thread: M8 Special features For screw-in milling cutters Conical seat for precise centring Lightweight design for reduced inertia Compact extension for recessed machining FAQ What thread does the extension use? The extension is fitted with an M8 thread for screw-in cutters, ensuring a secure mechanical connection with compatible tooling. Which shank diameter is required for the holder? The holder must accept a 16 mm shank; the extension’s shank diameter is 16 mm and the cutter-opening diameter is 14 mm. Is the VT503TM suitable for CNC applications? Yes, the VT503TM extension from Teknik Makina is suitable for CNC and manual milling where additional reach and maintained concentricity are needed. How much additional reach does the extension provide? The component adds an overall length of 100 mm, with a 30 mm conical engagement to maintain alignment under load. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
100mm Extension For Screw-In Milling Cutter M10 Shaft Ø20mm, 17.7mm Screw-In Opening - Teknik Makina
Take advantage of a compact extension that combines M10 thread security, a 20 mm shaft for stability and a 100 mm overall reach to maintain machining accuracy in confined setups — order the Teknik Makina extension via Metav Werkzeuge or consult our advisers for application guidance. Extension for screw-in milling cutters — 100 mm, M10 thread (Teknik Makina) The Extension for screw-in milling cutters is a threaded extension rod for use with thread-mounted milling cutters, designed to increase reach while retaining concentricity and stability in milling and CNC operations. M10 thread for secure cutter mounting 100 mm total length for extended reach 20 mm shaft diameter for stable clamping 17.7 mm cutter shank opening for compatibility Precision where length is required without sacrificing rigidity This extension delivers a measured increase in reach while minimising flex. The 100 mm total length is engineered to provide additional clearance in fixtures and deep cavities, yet the 20 mm shaft preserves lateral stiffness to reduce vibrations. The threaded interface with an M10 thread and a 30 mm cone seating ensures a firm mechanical connection; this reduces radial runout and supports repeatable positioning during serial machining. By selecting an extension with defined tolerances, shops can maintain part accuracy without resorting to ad‑hoc improvisation. Straightforward integration with thread-mounted cutters Designed for compatibility with screw-in style cutters, the extension features a 17.7 mm cutter shank opening and a 30 mm cone length for reliable seating of the cutter body. The geometry supports standard thread-mounted tooling systems commonly found in milling spindles and toolholders. Installation is a simple mechanical step: the extension is secured by the M10 thread into the cutter or holder and checked for concentricity before operation. This predictable assembly reduces setup time and helps teams keep production running smoothly. Built for dependable workshop use and supply continuity Constructed for routine industrial use, the extension offers a robust, low-mass solution at 0.235 kg that minimises added inertia while providing the necessary reach. The compact weight helps preserve spindle dynamics compared with longer, heavier adapters. Supplied by Teknik Makina and available through Metav Werkzeuge, the component is part of a broader catalogue that supports centralised sourcing, helping workshops reduce supplier complexity and secure dependable replenishment for precision tooling. For compatibility checks and fast supply of the Teknik Makina VT509TM extension, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 Technical data SKU: VT509TM Manufacturer: Teknik Makina Thread: M10 Total length: 100 mm Shaft diameter: 20 mm Cutter shank opening: 17.7 mm Cone length for screw-in cutter: 30 mm Weight: 0.235 kg eCl@ss: 21189208 ETIM: EC002219 Data Total length: 100 mm Shaft diameter: 20 mm Cutter shank opening: 17.7 mm Cone length: 30 mm Weight: 0.235 kg Thread: M10 Special features Application: screw-in milling cutters Compatible with thread-mounted cutters Files: 2 product documents attached Brand: Teknik Makina FAQ What is the main purpose of this extension? The extension VT509TM by Teknik Makina increases reach for thread-mounted milling cutters, providing an additional 100 mm overall length while maintaining secure mounting via the M10 thread. Which cutter shank sizes fit the extension? The extension accepts cutter shanks up to the specified opening of 17.7 mm, allowing direct seating of compatible screw-in milling cutters. How is the extension mounted and secured? Mounting is via the M10 threaded interface; the 30 mm cone length provides seating for the cutter and ensures a firm mechanical connection once tightened. Will using the extension affect spindle balance? The extension weighs 0.235 kg, which is modest; however, balancing should be checked after installation if high-speed machining or precision balancing is required with the extended assembly. What are the key dimensions to verify before use? Verify the 100 mm total length, shaft diameter 20 mm, cutter opening 17.7 mm and the M10 thread to ensure compatibility with the intended cutter and toolholder. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
100mm Extension for Screw-In Milling Cutter With 20mm Shank, M10 Thread - Teknik Makina
Take advantage of an increased working reach combined with secure clamping and a compact, lightweight design for smoother toolpaths and reliable machining cycles. The extension’s 20 mm shank, M10 thread and 100 mm overall length deliver practical reach without compromising stability — order the extension directly via Metav Werkzeuge or ask the consultants for application advice. Extension for Screw-in Milling Cutters VT508TM — 100 mm overall length, 20 mm shank | Teknik Makina The Extension for Screw-in Milling Cutters VT508TM is a precision adapter designed to extend screw-in milling cutters for CNC and manual milling operations, offering increased reach and stable seating for demanding toolpaths. Stable 20 mm shank for secure clamping M10 thread for screw-in cutter compatibility 100 mm overall length for extended reach Lightweight 0.238 kg for reduced spindle load Extend reach without compromising machining stability Extending the working length of a screw-in cutter allows access to deeper pockets or recessed features without resorting to long, flexible toolholders. The VT508TM acts as a precision adapter that preserves the cutter’s seating geometry while adding reach. Longer reach is achieved without significant loss of stiffness thanks to the carefully dimensioned shank and taper interface, which maintain concentricity and help avoid chatter. This results in more consistent surface finish and fewer interrupted machining cycles, supporting higher throughput in both prototype and production environments. Secure clamping and predictable dynamic behaviour A reliable connection between cutter and holder is essential for repeatable results. The adapter’s 20 mm shank and M10 thread provide a firm mechanical interface and a defined engagement length, while the conical seating section of 30 mm ensures axial alignment. The combination of secure thread engagement and a tapered fit reduces the risk of micro-movement under load, improving runout behaviour and tool life. The extension’s lightweight construction (0.238 kg) keeps additional centrifugal load low, helping to preserve spindle bearings and maintain dynamic balance at typical machining speeds. Easy integration into workshop tooling and process flow The extension is intended for straightforward use with standard screw-in milling cutters and common toolholding setups, so integration into existing tool libraries is simple. By avoiding special bespoke holders, shops can reduce inventory complexity and react faster to changing job requirements. The adapter supports efficient preparation on the toolbench and contributes to a leaner workflow: fewer tool changes and less repositioning mean shorter cycle times. Combined with Metav’s emphasis on reliability and supply from the Emmerich quality hub, this extension supports consistent production results across diverse applications. For a tailored recommendation on using the VT508TM extension from Teknik Makina, contact Metav Werkzeuge in Emmerich for application guidance — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: VT508TM Manufacturer: Teknik Makina SKU: VT508TM Numbers / Core technical data Shaft diameter: 20 mm Shank opening for screw-in cutter: 17.7 mm Cone length for screw-in cutter: 30 mm Overall length: 100 mm Weight: 0.238 kg Thread: M10 eCl@ss: 21189208 ETIM: EC002219 Special features Suitable for screw-in milling cutters Precision adapter for extended reach Compact and lightweight design Designed for stable seating and reduced runout FAQ What is the shank diameter of the extension? The extension has a 20 mm shank; the VT508TM is specified with this diameter to ensure stable clamping in compatible toolholders. Which thread does the adapter use for the cutter connection? The adapter features an M10 thread, making it compatible with screw-in milling cutters that employ the same thread form. How long is the extension in total? The overall length is 100 mm, providing extra reach where standard holders are too short. Is the extension heavy and will it affect spindle balance? At 0.238 kg the VT508TM is lightweight; this helps to keep additional centrifugal loading minimal and supports predictable dynamic behaviour. Which cutter type is this designed for? This adapter is intended for screw-in milling cutters and enables secure mounting and extended reach when those cutters are employed. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
100mm Extension For Screw-In Milling Cutter With M8 Thread, 16mm Shank Diameter - Teknik Makina
Take advantage of a compact, M8‑threaded connection and a 100 mm overall length to extend tool reach without sacrificing rigidity; the 16 mm shank and 14 mm cutter opening ensure a secure fit for standard screw‑in milling cutters. Order the (Extension for screw‑in cutter) directly via (Metav Werkzeuge) or ask our consultants if needed. Extension for Screw‑In Cutter VT502TM — 100 mm overall length, M8 thread (Teknik Makina) The Extension for screw‑in cutter VT502TM is a purpose‑built holder extension that increases machining reach for screw‑in milling cutters while maintaining run‑out stability in workshop and light industrial applications Secure M8 threaded connection for reliable mounting 16 mm shank for rigid machine tool clamping Compatible with 14 mm cutter openings 100 mm overall length for extended reach Increased reach with retained rigidity for precision machining This extension is engineered to extend the working envelope of screw‑in milling cutters without compromising stability. The 100 mm overall length provides extra reach for recessed features and hard‑to‑access geometries, while the 16 mm shank maintains a robust clamping interface to reduce vibration and run‑out. The M8 threaded joint is standardised, giving a tight mechanical coupling that supports consistent tool positioning; this reduces setup iterations and contributes directly to higher first‑pass accuracy in series and single‑piece production. Quick fitting and secure interface explained Fitting is straightforward: the extension accepts cutters with a 14 mm cutter opening and seats against the tool via a 30 mm cone engagement, ensuring axial alignment. The 30 mm cone length acts as a guiding seat that centres the insert‑style cutter, while the M8 thread secures axial load transfer during milling. For machinists unfamiliar with threaded cutter systems, the combination of a locating cone and fine mechanical thread means fewer adjustments are required at the machine, shortening preparation time and improving throughput on repetitive tasks. Practical benefits for workshop and jobbing environments Designed for everyday use in workshops and small production facilities, the extension combines lightweight handling (approx. 0.153 kg) with mechanical reliability. The compact mass reduces additional inertia on the spindle in hand‑operated setups and portable machines, which is beneficial where delicate control of cutting forces is required. By choosing a purpose‑made extension rather than ad‑hoc adaptors, shops gain predictable performance and reduced risk of tool failure, supporting a continuous production flow and consistent surface finish quality. For precise advice on integrating this Teknik Makina extension into existing toolholders, or to request order details from Metav Werkzeuge, please contact our team who can confirm suitability and availability. Technical data Article number: VT502TM Manufacturer: Teknik Makina Measurements Overall length: 100 mm Shank diameter: 16 mm Shank opening for cutter: 14 mm Cone length for screw‑in cutter: 30 mm Thread: M8 Weight: 0.153 kg Special features Suitable for screw‑in milling cutters Threaded M8 connection for secure mounting Locating cone for axial alignment Lightweight design for reduced spindle inertia FAQ What cutter types fit this extension? The extension accepts screw‑in milling cutters designed for a 14 mm opening; the locating cone and M8 thread provide a secure seat for standard screw‑in cutter systems such as those used in light milling operations. Is the extension compatible with my collet or holder? Compatibility depends on the machine’s toolholder accepting a 16 mm shank; the extension’s 16 mm diameter is intended for holders and collets rated for that shank size and will give a rigid connection when correctly clamped. How does the 30 mm cone length benefit accuracy? The 30 mm cone engagement centres the cutter axially before the thread is tightened, improving concentricity and reducing run‑out compared with non‑locating adaptors; this supports repeatable machining results. Can the extension be used for long overhang operations? The 100 mm overall length increases reach but also raises bending moment; the extension is optimised for moderate overhangs where the 16 mm shank still provides sufficient stiffness for accurate cuts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
10mm Screw-In Cutter For APMT 0602 Indexable Inserts, M6 Thread, 2 Flutes - Teknik Makina
Combining a secure M6 screw mounting, a compact 10 mm cutting diameter and two cutting edges, this screw-in milling cutter delivers consistent, efficient steel machining and straightforward insert changes; order the part directly via Metav Werkzeuge or consult our specialists for application advice. Screw-in milling cutter VT220TM by Teknik Makina — compact 10 mm diameter, M6 thread The screw-in milling cutter VT220TM is designed for precision metalworking where a compact head and secure screw mounting are required, suitable for use with Korloy indexable inserts in workshop and production environments. Secure M6 thread for stable mounting 10 mm cutting diameter for compact machining Two cutting edges for efficient material removal Compatible with Korloy indexable inserts Faster setup and dependable cutting performance for production runs The screw-mounted head offers a stable M6 connection and a 15 mm thread height, which together reduce vibration and ensure repeatable positioning on the toolholder. This results in consistent cutting conditions and fewer rejects during series production. The compact 10 mm diameter focuses forces close to the spindle axis, allowing tighter access in confined geometries while maintaining a clean chip flow. The design is especially suited to steel machining where rigidity and repeatability are priorities. Easy insert changes and low-maintenance handling to reduce downtime A utilitarian fastening system using a Torx screw (M1.8×4.1) with a T6 key enables quick and secure insert replacement without specialised tooling. The cutter’s two-edged configuration simplifies reconditioning intervals and makes index changes fast, which translates into reduced machine idle time and higher overall equipment effectiveness. Clear, standardised fixing components mean maintenance can be executed reliably by trained workshop staff. Compact design that supports versatility and workshop efficiency With an overall length of 40 mm and a weight of approximately 0.01 kg, this insert-holding cutter keeps the centre of gravity close to the spindle, helping to preserve surface finish and tool life in fine machining tasks. The screw-in system suits a modular tool strategy: heads can be swapped quickly to adapt to different operations without changing the holder. Compatibility with Korloy indexable inserts broadens tooling choices and supports inventory rationalisation for production planners. Contact Metav Werkzeuge for tailored advice on the Teknik Makina VT220TM screw-in milling cutter and arrange supply directly from Emmerich by phone +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: VT220TM Manufacturer: Teknik Makina Diameter: 10 mm Overall length: 40 mm Thread: M6 Thread height: 15 mm Cutting edges: 2 Weight: 0.01 kg Torx screw: M1.8x4.1 Torx key: T6 Compatible inserts manufacturer: Korloy Mounting type: screw-in cutter FAQ What insert types are compatible with this screw-in milling cutter? The VT220TM is specified for use with Korloy indexable inserts and accepts standard APMT-style indexable inserts compatible with Korloy designs. How is the cutter secured in the toolholder? The cutter uses an M6 screw mounting with a 15 mm thread height for secure fixation; the insert is locked using the supplied Torx screw (M1.8×4.1) tightened with a T6 key. Is the VT220TM suitable for steel machining? Yes, the cutter’s compact geometry and rigid M6 connection make the VT220TM appropriate for demanding steel machining tasks where stability and repeatability are required. Can the insert be changed quickly on the shop floor? Insert replacement is fast and maintenance-friendly thanks to the Torx screw fastening system and standardised fixing components. Does the cutter support versatile tool strategies in small batch production? The compact design and screw-in mounting enable rapid head changes and flexible tooling setups, supporting small-batch and mixed-production workflows. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
12mm Screw-In Milling Cutter For APMT 0602 Indexable Inserts, M6 Thread, 3 Flutes - Teknik Makina
Take advantage of a compact, precision‑engineered screw‑in milling cutter that delivers secure clamping and reliable chip control in restricted spaces; its 12 mm body and M6 thread ensure compatibility with standard small‑diameter setups while the Torx fastening and three cutting edges reduce downtime. Order directly via Metav Werkzeuge or request bespoke advice from our consultants. VT221TM Screw-in Milling Cutter — 12 mm, M6 thread, Teknik Makina VT221TM screw‑in milling cutter for APMT 0602 indexable inserts, optimised for compact machining and quick insert changes Compact 12 mm diameter for tight spaces M6 thread with 15 mm thread height Secure Torx fastening M1.8 x 4.1, T6 Three cutting edges for stable chip control Stable clamping for consistent machining results The solid design with an M6 thread and 15 mm thread height gives the tool reliable seating in small adaptors and compact spindles. With a 12 mm body and total length of 40 mm, the holder minimises overhang and reduces vibration, which supports a steady surface finish and longer insert life. The supplied Torx screw specification (M1.8 x 4.1) and T6 key interface provide a repeatable, maintenance‑friendly fastening method that helps to shorten tool change cycles and improve uptime. Economical insert strategy for efficient maintenance Designed to accept APMT 0602 indexable inserts, the cutter enables quick insert swaps and straightforward wear management. Compatibility with Korloy‑type inserts ensures a broad choice of grades and geometries for different materials and cutting conditions. The indexable approach reduces tooling costs over time because worn cutting edges are replaced rather than the whole cutter body, combining operational economy with predictable process control. Process benefits from an optimised cutting geometry Equipped with three cutting edges, the design balances chip formation and radial forces for secure cutting in interrupted and continuous milling operations. The lightweight construction (approx. 0.02 kg) lowers centrifugal stresses at higher speeds and helps maintain toolpath accuracy. These characteristics translate into dependable cycle times and repeatable part quality, making the holder suitable for small‑batch production or finishing passes where stability matters. Practical handling and serviceability on the shop floor The assembly is engineered for straightforward service: the Torx screw can be accessed with a common T6 wrench, and insert replacement is rapid thanks to the screw‑in clamp concept. The compact dimensions also make storage and logistics simpler, while the clear specification of fastening and thread details aids purchasing and inventory management. The VT221TM is produced by Teknik Makina, reflecting industrial manufacturing standards for precision holders. For reliable supply of the Teknik Makina VT221TM screw‑in milling cutter and expert advice on insert selection or application, contact Metav Werkzeuge in Emmerich: info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: VT221TM Manufacturer: Teknik Makina SKU: VT221TM Dimensions & measures Diameter: 12 mm Total length: 40 mm Thread: M6 Thread height: 15 mm Weight: 0.02 kg Cutting edges: 3 Features & compatibility For APMT 0602 indexable inserts Compatible insert manufacturer: Korloy Torx screw: M1.8 x 4.1 Torx key size: T6 Screw‑in holder design FAQ Which inserts fit this holder? The holder is specified for APMT 0602 indexable inserts and is compatible with Korloy‑type APMT inserts. What fastening is used to secure the insert? Insert clamping is achieved with a Torx screw (listed as M1.8 x 4.1) that is tightened with a T6 key. What are the key dimensions to check for machine compatibility? Important dimensions are 12 mm diameter, 40 mm overall length and an M6 thread with 15 mm thread height. Who manufactures this screw‑in milling cutter? This product is manufactured by Teknik Makina and is distributed through Metav Werkzeuge under the SKU VT221TM. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Extension For Screw-In Cutters M12, 25mm Shank Diameter, 40mm Taper Length - Teknik Makina
Take advantage of a secure M12 connection and a 150 mm overall length to extend machining reach without compromising rigidity; the compact 25 mm shank ensures compatibility with standard holders. Order the extension via Metav Werkzeuge or consult the Metav team for technical matching. Extension for screw-in cutters VT514TM by Teknik Makina — 150 mm reach, M12 thread Extension for screw-in cutters VT514TM provides additional reach for screw-in cutter systems, designed for milling applications where extended tool projection is required without sacrificing runout performance. M12 thread for secure connection 150 mm overall length for extended reach 25 mm shank diameter for standard holders 40 mm cone length ensuring stable seating Greater reach while maintaining stability With an overall length of 150 mm, this extension increases operational reach for screw-in cutter setups while preserving axial integrity. The 25 mm shank is sized for common toolholder standards, keeping the centre of mass predictable during rotation. Longer projections are often associated with greater deflection; the combination of shank diameter and a precise seating geometry reduces lateral movement and helps maintain consistent machining results. This makes the accessory suitable for tasks that demand extended clearance, such as machining deep pockets or accessing recessed features, while retaining a focus on measurable performance. Secure interface and precise seating for repeatable results A dependable connection is central to repeatable machining. The M12 thread pairs with a 40 mm cone length to provide a secure seating area, and the 20.7 mm opening for the screw-in cutter ensures correct alignment at the interface. These dimensions are chosen to deliver a compact but robust joint that resists loosening under typical milling loads. By translating geometric accuracy into operational reliability, the extension supports consistent runout behaviour, which is essential for maintaining surface finish and tool life in production environments. Designed for workshop efficiency and compatibility The extension is tailored to integrate with common screw-in cutter systems and standard holders, reducing the need for multiple bespoke adaptors. At a weight of 0.546 kg, the component is substantial enough to feel robust without unduly increasing spindle load. Workshops benefit from lower tooling complexity: utilising a single, well-specified extension can streamline tool changeovers and lower inventory diversity. The compact design simplifies storage and handling while enabling longer reach where required, supporting more flexible job planning on milling machines and machining centres. Reliability, procurement and quality assurance Manufactured for consistent function, the extension focuses on precise mechanical interfaces rather than surface treatments or coatings; declared dimensions translate directly to fit and stability in operation. Sourcing through a specialist distributor provides an additional quality filter: Metav Werkzeuge combines wide stock availability with technical competence, supporting reliable supply chains and practical advice for industrial users. The product’s straightforward specification aids specification checks and reduces the risk of mismatched interfaces during procurement and assembly. Contact Metav Werkzeuge for delivery and technical matching of the VT514TM extension — the Metav team can advise on suitability for specific cutter systems and arrange prompt dispatch from Emmerich Technical data Article number: VT514TM Manufacturer: Teknik Makina Name: Extension for screw-in cutters Weight: 0.546 kg Dimensions and core data Overall length: 150 mm Shank diameter: 25 mm Opening for screw-in cutter: 20.7 mm Cone length: 40 mm Thread: M12 Features and compatibility Suitable for screw-in cutters Standard shank for common holders Designed for extended reach in milling applications FAQ What machines is the extension compatible with? The extension for screw-in cutters VT514TM is compatible with milling machines and machining centres that accept standard holders and screw-in cutter systems; confirmation of holder sizes is advised before fitting. How does the M12 thread affect connection security? The M12 thread on the VT514TM provides a compact, secure mechanical interface that, when combined with the cone length, ensures stable seating and reduced risk of loosening under normal milling loads. Is the extension suitable for heavy-duty machining? The extension is designed for extended reach applications with a robust shank diameter and precise seating; suitability for heavy-duty operations depends on the specific machine, speeds and feeds, and should be evaluated against those parameters. What are the critical dimensions to check before ordering? Confirm the overall length (150 mm), shank diameter (25 mm), the opening for the screw-in cutter (20.7 mm) and the thread (M12) to ensure compatibility with the existing tool system. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Extension For Screw-In Milling Cutter 16mm Shank, M8 Thread - Teknik Makina
Take advantage of a precise combination of extended reach and secure threaded attachment: the 150 mm overall length and M8 interface enable deeper machining without compromising clamping stability. Order the VT504TM directly via Metav Werkzeuge or consult Metav's technical team for application matching. Extension for screw-in cutter VT504TM — Teknik Makina, 150 mm, M8 thread Extension for screw-in cutter VT504TM delivers a compact solution for extending the reach of screw-in milling cutters in constrained setups and deeper machining operations. *150 mm overall length *M8 threaded interface for secure attachment *16 mm shank for standard toolholders *Lightweight design at 0.234 kg Extended reach with industrial-grade stability The VT504TM extension provides a reliable method to increase working depth while maintaining machining stability. With an overall length of 150 mm, the component allows access to recessed features and deeper pockets without the need for improvised extensions that increase runout. The M8 thread forms a positive, repeatable mechanical connection to compatible screw-in cutters; this threaded coupling reduces axial play and supports consistent tool positioning. For production or maintenance environments where tool repeatability is essential, this extension balances reach with functional rigidity to support accurate machining outcomes. Secure connection and controlled concentricity Designed for compatibility with screw-in milling cutters, the extension features a 16 mm shank and a screw-in opening sized at 14 mm, matched to a 30 mm cone length for the cutter interface. The combination of 16 mm shank geometry and a precision-threaded M8 interface promotes stable clamping in common collet or chuck setups. By keeping shank runout low and the clamped length sufficient, the accessory helps to preserve cutting-edge life and surface finish. The product’s geometry is explained here in plain terms: the cone length ensures the cutter seats fully in the extension, the shank diameter suits standard holders, and the thread locks the assembly for repeatable performance. Low mass for improved handling and dynamic behaviour At just 0.234 kg, this extension is lightweight yet purpose built for workshop use. Reduced mass at the tool end lowers centrifugal forces during rotation and simplifies dynamic balancing when high spindle speeds are required. For machinists, this translates into easier tool changes, reduced spindle load, and a lower tendency for chatter in many common applications. The modest weight also supports manual handling during set-up and maintenance, while still providing sufficient material to withstand regular workshop use. Practical compatibility and straightforward installation The unit has been specified to fit into standard machining workflows: an M8 threaded interface for the cutter, a 14 mm screw-in opening to accept the cutter root, and a 16 mm shank to suit common holders. Installation is mechanical and direct — the cutter is screwed into the extension and the shank is secured in the toolholder — eliminating the need for adaptors or special fixtures. For complex assemblies or unusual machine interfaces, Metav’s documentation and product experts are available to clarify fitment options and to recommend appropriate clamping practices to preserve accuracy and safety. For detailed application advice, to confirm fitment on specific machines, or to order the Teknik Makina VT504TM extension with its M8 threaded interface, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or e‑mail info@metav-werkzeuge.com Technical data Article number: VT504TM Manufacturer: Teknik Makina Facts Total length: 150 mm Shank diameter: 16 mm Screw-in cutter opening: 14 mm Cone length for screw-in cutter: 30 mm Thread: M8 Weight: 0.234 kg Special features Threaded interface for screw-in cutters Compatible with screw-in milling cutters Compact extension for deeper reach FAQ Which cutters are compatible with this extension? The VT504TM extension for screw‑in cutter by Teknik Makina is compatible with screw-in milling cutters that match an M8 threaded connection and a 14 mm root diameter; check cutter specifications against these dimensions. How does the M8 thread affect setup security? An M8 threaded interface on the VT504TM creates a positive mechanical connection between extension and cutter, improving axial stability and repeatability during repeated mounting and demounting. Can the extension be used for deep pocket machining? Yes, the 150 mm overall length enables deeper reach for recessed machining tasks while the design aims to maintain clamping stability for consistent cutting performance. Will the 0.234 kg weight influence spindle dynamics? The lightweight construction of 0.234 kg reduces tool end inertia and generally aids dynamic behaviour at higher spindle speeds, while still offering sufficient mass for stable handling. What holder dimensions are required for the shank? The shank diameter is 16 mm; the extension is intended for holders or collets that accept a 16 mm shank and secure it with the usual clamping methods. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Extension For Screw-In Milling Cutter 20mm Shank M10 Thread 17.7mm Opening, 150mm Length - Teknik Makina
Take advantage of the combination of dependable mounting, extended reach and precise compatibility to streamline machining setups. The M10-threaded extension delivers stable clamping with a 20 mm shaft and a 150 mm overall length, making it a practical choice for workshop and production environments — order via Metav Werkzeuge or consult our specialists for fitment advice. Extension for screw-in cutters VT510TM — M10 thread, 150 mm overall length (Teknik Makina) A robust Extension for screw-in cutters VT510TM engineered to extend tool reach in milling and finishing tasks while maintaining secure mounting for screw-in cutter systems. M10 thread for secure tool mounting 150 mm overall length for extended reach 20 mm shaft diameter for stable clamping Compatible with screw-in cutters with 17.7 mm opening Greater reach without sacrificing rigidity This shaft extension provides an effective way to reach recessed or hard-to-access features while retaining machining stability. The 150 mm total length increases working reach, and the 20 mm shaft diameter helps preserve torsional stiffness during cutting operations. For setups that require screw-in cutter systems, the integrated M10 thread ensures a positive mechanical connection, reducing unwanted micro-movement. This results in fewer re‑setups and less downtime, which can translate into measurable efficiency gains on the shop floor. Precise fit and concentric mounting for consistent finishes Compatibility with cutters that have a 17.7 mm opening is ensured by the designed shaft geometry and taper. The 40 mm taper at the tool end promotes accurate seating and concentricity, helping to maintain surface finish and dimensional consistency across serial parts. Where surface quality and repeatability matter, a correctly matched extension reduces vibration and run‑out, producing smoother tool engagement and less tool wear — a clear advantage for both prototype work and small-batch production. Practical workshop benefits and handling Weighing in at approximately 0.357 kg, the extension is easy to handle during tool changes yet substantial enough to avoid flex under moderate cutting loads. The unit’s compact profile and standard thread format simplify storage and tool management within existing arbors, so integration into current tool inventories is straightforward. For shops using screw-in cutters, this accessory increases versatility by enabling a greater range of machining envelopes without additional specialised holders. Contact Metav Werkzeuge for specification checks or to confirm compatibility of the Teknik Makina extension VT510TM with existing screw-in cutters; our Emmerich team provides expert guidance and reliable supply for industrial tooling needs Technical Data SKU: VT510TM Manufacturer: Teknik Makina Thread: M10 Total length: 150 mm Weight: 0.357 kg Shaft diameter: 20 mm Cutter opening diameter: 17.7 mm Taper length: 40 mm FAQ What thread does the extension use and is it standard for screw-in cutters? The extension uses an M10 thread, which is a common mounting thread for many screw-in cutter systems; VT510TM is therefore compatible with standard M10 fittings used in workshop tooling. Can the extension maintain concentricity for finishing passes? Yes, the 40 mm taper and precise shaft dimensions of the VT510TM support accurate seating and help maintain concentricity for consistent finishing results. Which shaft diameter ensures stable clamping during milling? The 20 mm shaft diameter provides a balance between rigidity and accessibility, supporting stable clamping under typical milling and finishing loads. Is the extension suitable for deep or recessed machining operations? The 150 mm overall length is intended to extend reach for recessed features while preserving mounting security, reducing the need for complex holder assemblies. How heavy is the extension and does weight affect handling? At about 0.357 kg, the extension is light enough for easy handling during tool changes while remaining robust enough to minimise flex during operation. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Extension For Screw-In Milling Cutter 40mm Cone Length, M10 Thread - Teknik Makina
Take advantage of a secure M10 connection, a 20 mm shank for stable clamping and a compact 150 mm overall length to reach deeper pockets without compromising rigidity; order directly via Metav Werkzeuge or consult our specialists for compatibility and supply. Extension for screw‑in cutters VT511TM — M10 threaded, 150 mm overall length (Teknik Makina) Extension for screw‑in cutters VT511TM designed to extend tool reach for milling operations where a precise, secure connection to screw‑in cutters is required M10 threaded connection for secure fitting 150 mm overall length for extended reach 20 mm shank diameter for stable clamping Compatible with screw‑in cutters (17.7 mm opening) Reach deeper features with maintained stiffness The extension delivers an extended reach of 150 mm overall length while keeping axial stiffness high. By increasing reach without resorting to longer, unsupported tooling, the adapter reduces vibration and maintains cutting accuracy; the combination of a 20 mm shank and a precisely machined taper ensures that the toolholder remains rigid under load. This means fewer reworks and improved component quality in milling and finishing operations. Secure mechanical interface for reliable toolholding A decisive element is the M10 thread and the internal seating designed for screw‑in cutters with a 17.7 mm opening. The engagement is aided by a 40 mm taper length, which centres the cutter and minimises radial runout. For operations where repeatability matters, this mechanical interface provides a secure fit and quick replacement of cutters while preserving concentricity and surface finish. Practical workshop advantages and compatibility Weighing in at 0.354 kg, the extension is lightweight yet sufficiently robust for typical workshop use. The standard 20 mm shank makes it compatible with common collet chucks and toolholders that accept this diameter. As an accessory for screw‑in milling cutters, the component simplifies setups by extending reach without introducing complex fixturing, improving throughput in small-batch production and maintenance tasks. For precise extension solutions from Teknik Cutting Tools, contact Metav Werkzeuge for tailored advice and reliable supply from Emmerich — eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: VT511TM Manufacturer: Teknik Makina Overall length: 150 mm Shank diameter: 20 mm Cutter opening diameter: 17.7 mm Taper length: 40 mm Weight: 0.354 kg Thread: M10 Suitable for screw‑in cutters Brand: Teknik Makina FAQ Is the extension compatible with standard screw‑in cutters? Yes. The extension is designed for screw‑in cutters with a 17.7 mm opening and secures via the M10 threaded connection, matching the VT511TM specification. Which shank holders accept this extension? The extension uses a 20 mm shank and is suitable for toolholders and collets that accept 20 mm shanks. How does the taper length influence accuracy? The 40 mm taper length centres the cutter in the seating to reduce radial runout, improving concentricity and surface finish during milling. What are the exact dimensions and weight? Overall length 150 mm, shank diameter 20 mm, cutter opening 17.7 mm, taper length 40 mm; weight 0.354 kg. How is the cutter secured to the extension? The cutter is secured by the M10 threaded connection and the internal taper seating, providing a mechanically stable interface. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Extension For Screw-In Milling Cutter Holder M8, 16mm Shank Diameter - Teknik Makina
Take advantage of the combination of precise fitment, extended reach and light weight to streamline machining set-ups and reduce tool changes; order the extension directly via Metav Werkzeuge or ask the consultants for compatibility advice. Extension for screw-in cutters VT505TM — 150 mm reach, M8 thread (Teknik Cutting Tools) A compact tool extension, the Extension for screw-in cutters VT505TM increases reach for threaded milling cutters in CNC and manual machines while maintaining secure clamping and low additional spindle load. 150 mm overall length for increased reach M8 thread for standard screw-in cutters 16 mm shaft for robust tool clamping Lightweight: 0.23 kg reduces spindle load Secure connections and extended working range for improved cycle flow The extension is engineered to provide a reliable threaded connection and added reach without compromising stability. With a M8 screw interface and a full 150 mm overall length, the device is intended to extend the effective working distance of screw-in milling cutters while preserving concentricity. This reduces the need for repositioning or specialised long-reach cutters and supports smoother production sequences in batch and single-part operations. The combination of defined thread geometry and controlled dimensions translates into predictable behaviour under cutting loads. Compatibility clarified: what the dimensions mean for tool choice Compatibility is straightforward: the extension accepts screw-in cutters designed for a 14 mm opening and a cone length of 30 mm, and is mounted on a 16 mm shaft for standardised clamping. For workshops unfamiliar with these terms, the opening diameter refers to the receptacle on the cutter body, while the cone length describes the tapered engagement region that ensures axial and radial location. By matching these dimensions, the extension allows existing screw-in milling cutters to be used at increased reach without modifying cutter geometry or machine interfaces. Lower spindle stress and consistent clamping for reliable finishing Weighing just 0.23 kg, the accessory adds minimal rotating mass, which helps to keep spindle loads and dynamic imbalance low during operation. The 16 mm shaft diameter supports robust clamping, reducing runout risk compared with slender adapters. In practice this improves surface finish stability and reduces the frequency of rework caused by vibration-induced tool deviation. The result is a dependable extension that supports consistent part quality and efficient machine uptime. Practical supply and service considerations for workshop integration Sourced from Teknik Cutting Tools and distributed through Metav, the extension fits into a pragmatic supply chain designed for industry use. Metav’s inventory approach and product range support quick replacement and centralised procurement, which simplifies stock management for workshops and small manufacturers. If application-specific data or dimensional drawings are required for fixture checks, these details can be requested to verify fit before installation. For tailored compatibility checks or to arrange supply from Metav Werkzeuge, contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or call +49 2822 7131930 to discuss machine interfaces and delivery options Technical data Article number: VT505TM ECLASS: 21189208 ETIM: EC002219 Facts Overall length: 150 mm Shaft diameter: 16 mm Cutter opening diameter: 14 mm Cone length (cutter engagement): 30 mm Thread: M8 Weight: 0.23 kg Special features Designed for screw-in milling cutters Threaded M8 connection 16 mm shaft for standard clamping systems Light construction to reduce added spindle mass FAQ What types of cutters fit this extension? The extension is designed for screw-in milling cutters with a 14 mm opening and a 30 mm cone engagement; these dimensions ensure correct seating and secure clamping. Is the VT505TM suitable for CNC and manual milling machines? Yes, the VT505TM extension from Teknik Cutting Tools is intended for both CNC and manual setups where increased reach is required while maintaining a robust 16 mm shaft clamping. How does the weight influence spindle performance? At 0.23 kg the accessory adds minimal rotating mass; this helps to keep spindle load and dynamic imbalance low compared with heavier extensions. Can this extension be used with any M8-threaded cutter? The M8 thread provides a standardised connection, but correct fitment also depends on the cutter’s 14 mm opening and 30 mm cone length; matching all three dimensions is recommended. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Extension for Screw-In Milling Cutter M10 Shank 19mm, 17.7mm Screw-In Opening, 30mm Taper Length - Teknik Makina
Take advantage of a secure M10 screw-in connection, a 150 mm overall length for extended reach and a stable 19 mm shank to improve machining access and process reliability; order the extension directly via Metav Werkzeuge or consult our specialists for integration advice. Extension for screw-in cutters — M10 thread, 150 mm overall length by Teknik Makina The Extension for screw-in cutters is a threaded mounting adapter designed to increase tool reach and maintain concentricity when using thread-mounted milling cutters in CNC and manual machining setups. M10 threaded interface for secure mounting 150 mm overall length for extended reach 19 mm shank diameter for stable clamping Lightweight at 0.324 kg for easy handling Reach deeper without compromising stability The extension combines a 150 mm overall length with a 19 mm shank diameter to permit machining in deeper bores and recesses while preserving tool alignment. The longer reach reduces the need for intermediate setups and fixtures, which can shorten cycle times and lower logistical overhead. Thanks to the robust geometry, the adapter supports consistent runout behaviour, so concentricity is maintained and surface finish quality is not sacrificed when accessing difficult-to-reach features. Secure seating and reliable thread connection A standard M10 thread provides a repeatable, mechanical interface with thread-mounted cutters; the integrated seating cone of 30 mm length ensures a firm axial location for the cutter body. This design reduces micromovement under cutting loads and simplifies mounting: the screw-in system guarantees a direct mechanical lock that transfers torque efficiently, while the modest mass of 0.324 kg keeps dynamic imbalance to a minimum. The specified seating opening of 17.7 mm is the reference for compatible cutter bodies and clamping sockets. Practical fit into workshop workflows Intended for use with thread-mounted milling cutters within cutting-tool and CNC environments, the extension is a straightforward solution to extend tool reach without complex toolholder changes. The compact, lightweight nature supports quick handling during tool changes and minimises additional spindle load. By enabling access to deeper or recessed machining areas, this adapter can reduce fixturing time and increase throughput, supporting a smoother production flow and higher machine utilisation. Contact Metav Werkzeuge for advice on integrating the Teknik Makina extension into existing tooling setups and to secure reliable supply from Emmerich. Technical data Article number: VT507TM Manufacturer: Teknik Makina SKU: VT507TM eClass: 21189208 ETIM: EC002219 Facts Overall length: 150 mm Shank diameter: 19 mm Cutter seating opening: 17.7 mm Seating cone length: 30 mm Thread: M10 Weight: 0.324 kg Special features For screw-in cutters Thread-mounted interface Long cone for axial seating Lightweight design for reduced spindle load Suitable for CNC and manual milling applications FAQ What thread does the extension use? The extension uses an M10 threaded connection for screw-in mounting, ensuring a secure mechanical interface with thread-mounted cutters. Which cutter seating dimensions are required? The adapter is specified for cutter bodies with a seating opening of 17.7 mm and a seating cone engagement of 30 mm. How long is the extension and what benefit does that provide? With an overall length of 150 mm, the extension allows access to deeper bores and recessed features, reducing the need for additional fixturing or secondary setups. Is the adapter heavy and will it affect spindle balance? At 0.324 kg the adapter is lightweight; its compact mass helps to minimise additional imbalance, though final balance depends on the specific tool assembly. Which applications are best suited to this extension? The product is intended for use in milling and machining workflows with thread-mounted cutters, particularly where extended reach or reduced setup complexity is required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Extension for Screw-In Milling Cutter M12, 24mm Shank Opening 20.7mm, 40mm Taper Length - Teknik Makina
The combination of a secure M12 threaded connection and a 150 mm overall length provides extended reach without compromising seating stability; this supports efficient machining in recessed or hard-to-access areas. Order the extension directly via Metav Werkzeuge or ask our consultants if additional technical details are required. Extension for screw-in cutter VT512TM — M12 thread, 150 mm overall length (Teknik Makina) The Extension for screw-in cutter VT512TM is a precision tool extension designed to increase reach and ensure stable seating of screw-in cutters for milling and CNC toolholders. M12 thread for secure mounting 150 mm overall length for extra reach 24 mm shank diameter for standard holders 40 mm long taper for stable cutter seating Reach further while keeping tool stability The extended design delivers 150 mm overall length to access deeper bores and recessed features while retaining a compact footprint in the tool chain. The combination of a 24 mm shank and a long taper (40 mm) supports axial and radial stability, so concentric performance is preserved during high-precision operations. Choosing an extension with these dimensions reduces the need for secondary setups and enables machining tasks that would otherwise require bespoke fixturing or multiple operations. Secure connection engineered for repeatability A robust M12 thread provides a positive, reproducible interface; when combined with the 20.7 mm opening for the screw-in cutter, the connection is engineered to minimise runout and vibration. The extension’s mass (approx. 0.508 kg) has been balanced for stable handling in many standard toolholders, so the assembly is suited to routine workshop usage where repeatable positioning and quick changeovers are valued. Where concentricity is critical, the precise taper length improves seating and alignment. Practical benefits for workshop productivity Built to integrate into established tool systems, the VT512TM from Teknik Makina reduces handling complexity for tasks that need extra reach without sacrificing precision. The extension simplifies set-up procedures and shortens machining cycles by allowing cutters to remain mounted in a stable position while reaching otherwise inaccessible areas. The net effect is improved throughput and fewer interruptions for re-clamping or tool swaps, which supports more efficient batch and single-part production alike. Compatibility notes and installation guidance This extension is intended for use with screw-in cutters that fit an M12 seat and a cutter shank opening of 20.7 mm; the 24 mm exterior shank diameter matches many standard holders. The 40 mm taper length secures the cutter in the extension and promotes reliable seating. Compatibility should be confirmed against holder and cutter dimensions before ordering to ensure a correct fit and optimal performance. For tailored advice on the VT512TM extension from Teknik Makina or to confirm compatibility and delivery options, contact Metav Werkzeuge in Emmerich by phone +49 2822 7131930 or by email at info@metav-werkzeuge.com Technical data SKU: VT512TM Manufacturer: Teknik Makina Thread: M12 Overall length: 150 mm Weight: 0.508 kg Shank diameter: 24 mm Shank opening for screw-in cutter: 20.7 mm Long taper for screw-in cutter: 40 mm Core specifications Shaft diameter: 24 mm Opening for cutter: 20.7 mm Taper length: 40 mm Overall length: 150 mm Thread: M12 Weight: 0.508 kg Special features Suitable for screw-in cutters Secure M12 threaded connection Extended reach for deep milling Balanced design for stable seating FAQ Is the extension compatible with standard M12 screw-in cutters? The VT512TM extension is designed for cutters that use an M12 threaded seat and a shank opening of 20.7 mm; compatibility should be checked against the cutter and holder dimensions. Will the extension affect concentricity in critical operations? The long taper and 24 mm shank diameter are intended to maintain concentricity and stable seating; correct installation and inspection of the threaded connection will help ensure repeatable alignment. What toolholders are suitable for this extension? The extension’s 24 mm shank is compatible with holders that accept that diameter; confirm holder clamping range and runout specifications before use. How heavy is the extension and does weight require counterbalance? The VT512TM weighs approximately 0.508 kg; in most standard setups this mass is acceptable, but balance considerations should be made for very high-speed applications. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Extension For Screw-In Milling Cutter With 25mm Shank And M12 Thread, 40mm Cone Length - Teknik Makina
Take advantage of a secure M12 connection and a 150 mm reach to extend machining capability while preserving rigidity; the combination of a 25 mm shank and a 20.7 mm cutter opening supports stable clamping and predictable tool engagement. Order the extension for screw-in milling cutters directly via Metav Werkzeuge or ask our consultants if needed Extension for screw-in milling cutters VT515TM — M12 thread, 150 mm overall length (Teknik Cutting Tools) Extension for screw-in milling cutters VT515TM is a dedicated toolholder designed to increase reach for screw-in milling operations while maintaining concentricity and clamping stability in production environments M12 thread for secure cutter attachment 150 mm overall length for extended reach 25 mm shank diameter for rigid clamping Weighs 0.542 kg for balanced handling Gain extended reach without compromising engagement The extension provides a 150 mm overall length that allows deeper access to workpieces or additional clearance for fixturing, while the M12 thread and a 40 mm cone engagement ensure the cutter is positively located. The internal opening of 20.7 mm matches standard screw‑in cutter shanks, reducing adaptor stacks and preserving axial alignment. This construction minimises wobble and contributes to reliable repeatability in serial production, which in turn reduces scrap rates and set‑up iterations. Improve rigidity and surface quality with a stout shank A 25 mm shank diameter gives the assembly the necessary stiffness for moderate cutting loads, improving surface finish and extending cutter life through reduced vibration. The extension’s mass (approx. 0.542 kg) is optimised to balance inertia and dynamic stability, so toolpaths remain predictable at typical feed rates used in milling centres. For machine shops seeking consistent results, this means fewer corrective passes and a more efficient machining cycle. Integration and shopfloor benefits for production use Designed for compatibility with screw‑in milling cutters, the component simplifies tooling inventories by enabling existing cutters to reach otherwise inaccessible features. The straightforward mechanical interface shortens changeover time and supports standardised maintenance checks. In practice, the extension is suited to CNC machining centres and toolrooms where extended reach, secure attachment, and dimensional reliability contribute directly to throughput and process stability. For technical advice or to arrange supply of the Teknik Cutting Tools extension (VT515TM), contact Metav Werkzeuge’s specialists at info@metav-werkzeuge.com or call +49 2822 7131930 — assistance and regional supply from Emmerich are available Technical data Article number: VT515TM Manufacturer: Teknik Makina Thread: M12 Weight: 0.542 kg Core dimensions Overall length: 150 mm Shank diameter: 25 mm Cutter opening: 20.7 mm Cone engagement length: 40 mm Special features Screw‑in cutter compatibility Stout shank for improved rigidity Balanced mass for stable handling FAQ Which cutter shank sizes fit this extension? The extension accepts screw‑in milling cutters with a shank opening of 20.7 mm; the M12 threaded interface gives secure axial engagement for standard screw‑in cutters (Teknik Cutting Tools VT515TM). Is the component suitable for use in CNC machining centres? Yes — the 25 mm shank and robust design make the extension appropriate for CNC applications where added reach and rigidity are required. How much extra reach does the extension provide? The overall length of 150 mm increases access compared with standard holders, allowing machining of deeper pockets or improved clearance for fixtures. What ensures the cutter is securely retained? Retention is delivered through the M12 thread combined with a 40 mm cone engagement, which together ensure positive location and repeatable concentricity for the cutter. Can this extension affect surface finish or tool life? By increasing stiffness through the 25 mm shank and limiting play at the connection, the extension supports improved surface finish and can reduce premature cutter wear under comparable cutting conditions. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Extension For Screw-In Milling Cutter With M10 Thread, 19mm Shank Diameter - Teknik Makina
Take advantage of a precise, rigid extension designed for screw-in cutters: M10 thread for secure mounting and a 150 mm overall length for extra reach while maintaining concentricity and balance; order the extension via Metav Werkzeuge or request bespoke advice for integration into existing toolholders. Extension for screw-in milling cutters – M10 thread, 150 mm length by Teknik Makina The Extension for screw-in milling cutters is a purpose-built toolholder component that extends the working reach of screw-in cutters while preserving rigidity and runout control for workshop and CNC applications M10 thread for secure attachment 150 mm overall length for extended reach Shaft Ø 19 mm for rigid support Compatible with cutters with 17.7 mm opening Longer reach without compromising rigidity Extending cutter reach can often lead to vibration and loss of accuracy; this extension is engineered to avoid that. With a 150 mm overall length and a substantial shaft diameter of 19 mm, the bar provides added reach while maintaining lateral stability on the spindle. The design reduces deflection compared with slimmer extensions, so machining cycles remain predictable. In practice, this means fewer scrap parts and more consistent surface finish when working on longer or recessed profiles. Secure seating and consistent concentricity A precision M10 thread and a long taper of 30 mm on the seating section ensure that the cutter seats accurately and remains concentric under load. The mating opening of 17.7 mm is specified to match common screw-in cutter geometries, enabling a firm mechanical engagement that supports repeatable runout figures. For toolroom planners and production engineers, this translates into reliable radial control and reduced need for frequent re-adjustment during batch runs. Balanced weight and straightforward handling for workshop use Weighing 0.329 kg, the extension keeps spindle load modest while offering the extra length required for specialised operations. The moderate mass assists in maintaining rotational balance, which is advantageous on both high-speed and general-purpose machines. As a component for cutting tool assemblies, the unit helps streamline setups: fewer intermediate holders, more direct positioning and a lower risk of introducing additional error sources during assembly. For secure extended-reach milling applications, contact Metav Werkzeuge to discuss the Teknik Cutting Tools extension VT506TM and confirm compatibility with existing toolholders; Metav Werkzeuge provides fast, localised supply from Emmerich and practical advice for integration. Technical data Article number: VT506TM Manufacturer: Teknik Makina ECLASS: 21189208 ETIM: EC002219 Facts Overall length: 150 mm Shaft diameter: 19 mm Cutter opening (compatible): 17.7 mm Long taper (seating): 30 mm Thread: M10 Weight: 0.329 kg Special features For screw-in milling cutters Long taper seating for secure engagement Engineered for reduced deflection Suitable for workshop and CNC tool assemblies FAQ Is this extension compatible with all screw-in cutters? Compatibility depends on the cutter's mating opening and thread; the VT506TM by Teknik Makina is designed for cutters with a 17.7 mm opening and an M10 thread match What concentricity performance can be expected? When used with correctly matched screw-in cutters and a properly torqued M10 connection, the extension VT506TM delivers stable concentricity suitable for many finishing and profiling tasks Can the extension be used on high-speed spindles? The VT506TM’s 19 mm shaft and balanced mass of 0.329 kg support use on higher spindle speeds, provided the machine tool and holder meet the required balance and runout specifications How is the extension installed and secured? The component fits via the M10 thread and seats on a 30 mm taper; correct tightening and verification of seating ensure reliable engagement for routine machining Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
150mm Extension For Screw-In Milling Cutter With M8 Thread, 15mm Shank Diameter - Teknik Makina
Take advantage of the combination of extended reach, a secure M8 connection and a lightweight, workshop-ready design to keep machining processes efficient and reliable; order the extension directly via Metav Werkzeuge or consult our specialists for application guidance. Extension for Screw‑in Cutters VT501TM – M8 threaded arbor, 150 mm overall length (Teknik Makina) The Extension for Screw‑in Cutters is a threaded arbor extension designed to increase reach for screw‑in milling cutters in workshop and CNC environments. M8 thread for secure connection 150 mm overall length for extended reach 15 mm shank for standard toolholders Low weight 0.202 kg for balanced handling Extended reach while maintaining rigidity The arbor extension provides an additional 150 mm of overall length without compromising on rigidity. With a 15 mm shank, the extension is compatible with many common toolholders, enabling longer overhangs where access is restricted. This reduces the need for special long‑reach cutters and simplifies setups, allowing precise machining in deep or awkward positions while maintaining acceptable run‑out and stability for milling operations. Threaded seating for repeatable accuracy A secure M8 threaded connection and a 30 mm taper seating ensure a repeatable mechanical interface between the extension and screw‑in cutters. The tapered seating promotes concentric clamping and reduces micro‑movement under load, which translates into consistent tool performance and predictable surface finish. For users unfamiliar with tapered fittings: the cone creates a tight mechanical contact that centres the cutter and resists loosening during rotation. Balanced handling and quick integration Weighing 0.202 kg, the extension remains light enough to avoid excessive imbalance on high‑speed spindles while providing meaningful reach. Its geometry supports straightforward integration into existing tooling systems: the larger shank diameter offers mechanical stiffness, and the reduced mass compared with longer adaptors helps to limit spindle strain. Compatibility with standard holders reduces changeover time and simplifies stock management in mixed production environments. Practical productivity gains for workshops By using this threaded arbor extension, setups become more versatile: one arbor can serve multiple screw‑in cutters, cutting down on the number of specialised tools required. The result is fewer tool changes, reduced inventory complexity and faster turnaround on small to medium production runs. Combined with Metav Werkzeuge’s reliable supply chain and technical support from the Emmerich hub, this extension supports continuous workshop operation and gives buyers confidence in consistent product quality. Contact Metav Werkzeuge for tailored advice on Teknik Makina extensions and secure procurement from our Emmerich hub; technical consultants are available to discuss compatibility and ordering. Technical data SKU: VT501TM Manufacturer: Teknik Makina eClass: 21189208 ETIM: EC002219 Facts Shank diameter: 15 mm Cutter opening diameter: 12.7 mm Cone/taper length: 30 mm Overall length: 150 mm Weight: 0.202 kg Thread: M8 Special features Threaded arbor extension for screw‑in cutters Suitable for workshop and CNC applications Lightweight design for reduced spindle load Standard interface dimensions for common toolholders FAQ Is this extension compatible with standard screw‑in milling cutters? Yes. The Extension for screw‑in cutters (VT501TM) uses an M8 threaded connection and a 12.7 mm cutter opening diameter compatible with common screw‑in milling cutters from typical suppliers. How does the tapered seating affect accuracy? The 30 mm taper seating centres the cutter and increases clamping stability; this design improves concentricity and helps maintain consistent run‑out during milling. Will the weight impact spindle balance at high speeds? At 0.202 kg the extension is intentionally light to minimise imbalance; however, users should always check total assembly balance for very high spindle speeds and perform dynamic balancing if required. Can this arbor extension reduce the need for long‑reach cutters? Yes. By extending reach by 150 mm while keeping a rigid 15 mm shank, the extension allows standard cutters to access deeper features, reducing the necessity for a larger set of specialised long‑reach tools. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Extension For Screw-In Milling Cutter With M8 Thread, 15mm Shank Diameter - Teknik Makina
Take advantage of an extended, stable tool connection that improves accessibility in deeper cuts while keeping spindle load low; the M8 thread and 150 mm reach combine to deliver a reliable, repeatable mounting for screw-in indexable cutters. Order directly via Metav Werkzeuge or consult the technical team for selection and supply. Extension for screw-in cutters — 150 mm reach, M8 thread (Teknik Makina) Extension for screw-in cutters for use with screw-in indexable insert cutters, designed to extend working reach while maintaining concentricity and simple mounting 150 mm overall length for deeper reach M8 thread for secure screw-in connection 15 mm solid shaft for rigid support 12.7 mm opening for standard insert cutters Longer reach with predictable, machine-friendly performance The extension arbor provides a controlled increase in working distance without sacrificing precision. With an overall length of 150 mm, the unit is engineered to reduce the need for complex fixturing when machining recessed features or tooling fixtures. The solid 15 mm shaft offers stable support, which helps to reduce unwanted vibration and runout during operations, and the relatively low mass of 0.208 kg minimises additional spindle load. For workshop planners and production engineers, this means predictable machining cycles and fewer interruptions caused by tool instability. Secure mounting that keeps repeatability high Threaded connection via the M8 thread ensures a positive mechanical joint to the cutter body and contributes to consistent concentricity across repeated installations. The internal opening of 12.7 mm suits many screw-in indexable cutters and supports straightforward assembly with standard fastening hardware. The 30 mm cone length creates a reliable seating surface for the cutter, translating to repeatable radial and axial positioning. The result is an extension that preserves the original tool geometry and repeatability, reducing scrap rates and setup time. Simple integration into existing tooling systems Designed for practical compatibility, the extension fits into common tool setups for indexable cutters and is particularly useful where increased reach is required without converting to long overhang cutters. The component’s straightforward geometry permits quick verification of fit and alignment on the bench; the absence of complex adapters means fewer parts to manage in inventory. This practical design supports leaner tool management and faster changeovers in small-batch or mixed-production environments. Durable, production-oriented specification Although detailed material specifications are not supplied in the product data, the component’s dimensions and thread standardisation reflect a production-orientated mindset: standardised thread (M8), defined seating cone length (30 mm) and a measured shaft diameter (15 mm). These measurable parameters allow engineering teams to assess stiffness and dynamic behaviour in context with machine and cutter characteristics. Where higher rigidity or specific coatings are required, the extension can be evaluated alongside suitable cutter bodies to ensure compatibility with the intended machining task. For procurement or technical advice on Teknik Makina extensions: contact Metav Werkzeuge via info@metav-werkzeuge.com or call +49 2822 7131930 to confirm fitment and secure supply from Emmerich Technical data Article number: VT500TM Manufacturer: Teknik Makina Facts Overall length: 150 mm Shaft diameter: 15 mm Opening for screw-in cutter: 12.7 mm Cone length (seating): 30 mm Thread: M8 Weight: 0.208 kg Special features For screw-in indexable cutters Simple, standardised connection Low additional spindle mass Designed for repeatable mounting FAQ Which cutter types are compatible with this extension? The extension for screw-in cutters (VT500TM) is intended for screw-in indexable insert cutters; compatibility is determined by the cutter’s 12.7 mm mounting opening and M8 screw connection. How does the M8 thread affect mounting stability? The M8 thread used on the Technik Makina extension (VT500TM) provides a secure mechanical connection that contributes to repeatable seating and reduced axial movement during machining. What are the key dimensions to check before fitting? Confirm the cutter’s mounting opening (12.7 mm), the machine-side holder clearance for a 150 mm overhang, and the 15 mm shaft diameter to ensure correct fit and stiffness with the selected cutter body. Will the extension significantly increase spindle load? With a weight of 0.208 kg, the extension adds minimal mass; assessment should still be made in context with the spindle speed and cutter mass to maintain dynamic stability during operation. Can the extension be used with different brands of indexable cutters? The extension (VT500TM) is compatible with cutters that match the listed mounting dimensions and an M8 thread; cross-brand fit should be verified by checking the cutter’s mounting geometry. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
150mm Extension for Screw-In Milling Cutter, M12 Thread, 24mm Shank Diameter - Teknik Makina
Take advantage of the combination of precise fit, extended reach and solid connection for reliable milling operations. The extension’s 24 mm shank and M12 thread ensure consistent clamping and minimal runout, supporting smoother production. Order the extension directly via Metav Werkzeuge or consult the specialists for application advice. Extension for Screw-in Milling Cutter VT513TM — 24 mm shank, M12 thread (Teknik Makina) The Extension for Screw-in Milling Cutter is a tool extension designed to increase reach and maintain secure seating for screw-in cutters in milling and CNC applications. Solid 24 mm shank diameter M12 thread connection for secure attachment 150 mm overall length for extended reach 40 mm taper for tight cutter seating Extend reach while keeping rigidity and control The extension delivers a balance between reach and stiffness: with a 24 mm shank and a 150 mm overall length, the component provides increased access to recessed features while aiming to preserve tool stability. Longer tool extensions often risk vibration and loss of precision; the measured shank diameter here reduces that risk by maintaining a robust connection to the spindle or holder. This makes the accessory suitable where additional length is required without sacrificing repeatable performance. Reliable cutter seating and repeatable connection Designed for screw-in cutter systems, the tool features an M12 thread, a 20.7 mm cutter opening and a 40 mm taper for the mating cutter. The combination of thread and taper distributes clamping forces and supports axial alignment, which contributes to secure clamping and reduced runout compared with loose-fit adapters. The taper length enhances axial stability during milling, explaining why a properly matched extension can help preserve cutting geometry and surface finish in precision operations. Workshop compatibility and practical handling With a compact weight of 0.502 kg and straightforward geometry, the extension integrates into standard workshop workflows and CNC tool inventories. The accessory is intended for use with screw-in milling cutters and is produced for robust handling in repetitive machining contexts. Technical enquiries and specification checks are supported by Metav Werkzeuge, whose role as a precision partner helps ensure correct selection and a reliable supply chain for production and maintenance demands. Contact Metav Werkzeuge for tailored advice on integrating the Teknik Makina VT513TM extension into existing tooling setups and to discuss availability or delivery options Technical data Article number: VT513TM Manufacturer: Teknik Makina Product name: Extension for screw-in milling cutter Facts Shank diameter: 24 mm Cutter opening diameter: 20.7 mm Taper length (screw-in cutter): 40 mm Overall length: 150 mm Thread: M12 Weight: 0.502 kg Special features Intended for screw-in milling cutters M12 thread connection 40 mm taper for cutter seating Compact, workshop-friendly weight FAQ What shank diameter does the extension use? The extension is supplied with a 24 mm shank diameter, suitable for holders and collets designed for this dimension. Which thread and taper specifications are provided for cutter mounting? The VT513TM uses an M12 thread, a 20.7 mm cutter opening and a 40 mm taper to seat screw-in cutters securely. What is the overall length of the extension? The overall length is 150 mm, offering extended reach for machining deeper or recessed areas. How heavy is the extension and is it easy to handle? The extension weighs 0.502 kg, a compact mass that supports easy handling and practical workshop use. For which applications is this extension intended? The extension is intended for milling and CNC operations requiring increased tool reach with screw-in cutter systems. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com
16mm Screw-In Cutter 100° For BLMP 0603 Indexable Inserts, M8 Thread - Teknik Makina
Take advantage of a compact, screw‑in design that combines compatibility with BLMP 0603 indexable inserts, a 100° cutting angle for stable engagement and fast insert changes via a Torx screw—ideal for streamlined machining operations; order directly via Metav Werkzeuge or consult our specialists for application advice. Screw-in milling cutter VT190TM — 16 mm, 100° for BLMP 0603 Indexable Inserts (Teknik Makina) Screw-in milling cutter VT190TM for BLMP 0603 indexable inserts, designed for compact holders and precise, repeatable milling tasks in production and workshop environments 16 mm shank diameter for compact setups 100° cutting angle for stable engagement Compatible with BLMP 0603 indexable inserts M8 thread and M3x6.5 Torx screw (T8) Lightweight 44 g for easy handling High compatibility and mechanical clarity for standard indexable systems The screw‑in milling cutter VT190TM is engineered to interface reliably with common indexable systems. Its 16 mm diameter and M8 thread provide a compact mounting footprint while ensuring secure clamping. Compatibility with BLMP 0603 indexable inserts from Taegutec simplifies procurement and inventory: standardised inserts make tool replenishment predictable and keep set‑up times low. For operators new to indexable tooling, this configuration reduces complexity by using familiar insert geometries and a conventional screw‑in mounting. Stable cutting performance with straightforward handling A 100° cutting angle offers a balanced compromise between shearing and edge strength, promoting steady chip formation and reducing chatter in many milling operations. The tool features two cutting edges and a 25 mm cutting height, delivering effective material engagement across the insert length. At 41 mm total length and weighing only 44 g, the tool is easy to handle and manoeuvre in tight setups; the result is reduced operator fatigue and quicker changeovers when multiple tools are in use. Fast insert changes and efficient maintenance routines Insert replacement uses an M3x6.5 Torx screw secured with a T8 Torx key, allowing quick, repeatable fastening without specialised fixtures. The screw‑in design keeps assembly straightforward and maintenance predictable: worn inserts can be swapped in minutes, lowering machine downtime and improving throughput. This configuration supports a rational approach to tooling costs—indexable inserts and a durable cutter body keep life‑cycle expenses transparent and easier to manage than many integral tools. Practical applications and workshop integration The compact, screw‑in format suits shops that prioritise versatility and inventory efficiency. The tool works with the BLMP 0603 insert family and is often chosen where quick insert indexing and a secure clamping interface are required. Its modest overall length and lightweight construction make it well suited to smaller spindle clearances or secondary operations in a production cell. For customers seeking predictable, repeatable milling results with standard insert systems, this screw‑in cutter provides a pragmatic balance of performance and serviceability. Contact Metav Werkzeuge today to discuss how the VT190TM from Teknik Makina fits specific machining setups or to request stock information from our Emmerich warehouse at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: VT190TM Manufacturer: Teknik Makina Product name: Screw-in milling cutter Secondary designation: for BLMP 0603 Indexable Inserts eClass: 21180806 ETIM: EC011860 Core technical data Diameter: 16 mm Thread: M8 Thread height: 16 mm Cutting angle: 100° Cutting edges: 2 Cutting height: 25 mm Total length: 41 mm Weight: 0.044 kg Screw: M3x6.5 (Torx) Torx key: T8 Compatible inserts: BLMP 0603 Compatible insert manufacturer: Taegutec Special features Screw‑in mounting design Compatible with BLMP 0603 indexable inserts Secured with M3x6.5 Torx screw (T8) Compact overall length for confined set‑ups Two cutting edges for effective engagement FAQ Which indexable inserts fit this cutter? The screw‑in milling cutter VT190TM is compatible with BLMP 0603 indexable inserts and is optimised for inserts from Taegutec What is the shank diameter and thread specification? The VT190TM has a 16 mm shank diameter and an M8 thread for screw‑in mounting How are the inserts secured in the cutter? Inserts are fastened with an M3x6.5 Torx screw using a T8 key on the VT190TM How many cutting edges does the tool provide? The VT190TM features two cutting edges, delivering consistent engagement across the insert What are the key dimensions of the cutter? Key dimensions for the VT190TM: total length 41 mm, cutting height 25 mm, weight 0.044 kg Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com
16mm Screw-In Cutter 90° For ADMX 0702 Indexable Inserts M8, 4 Cutting Edges, M2x4.2 Torx Screw - Teknik Makina
Take advantage of compact, secure mounting and 90° cutting geometry to achieve precise shoulder cuts in confined setups; combine low mass and easy insert replacement for shorter downtime. Order the tool directly via Metav Werkzeuge or consult our specialists for delivery and suitability advice. Screw-in milling cutter VT200TM – 16 mm diameter, 90° cutting angle by Teknik Makina A compact screw-in milling cutter VT200TM designed for turning and face operations with ADMX 0702 indexable inserts, engineered for tight-access machining and rapid insert changes. 16 mm diameter for compact machining M8 screw-in thread, 18 mm thread length 90° cutting angle for square shoulder cuts Four cutting edges for balanced cutting action Compatible with Pramet ADMX 0702 inserts Precise performance in confined spaces The VT200TM offers a 16 mm body and an overall length of 41 mm, which reduces overhang and improves rigidity in restricted tool positions. The small mass of 0.041 kg lowers centrifugal forces and vibration, resulting in steadier cutting conditions and improved surface finish. For operations where access and stability matter, the compact geometry enables repeatable shoulder and facing cuts while maintaining consistent tool life. The design therefore translates directly into fewer rejects and less rework, supporting efficient production flow. Fast, secure mounting and straightforward insert handling Mounting is accomplished via an M8 screw-in thread with a thread engagement height of 18 mm, ensuring a secure connection to the toolholder; the clamping screw specification is M2x4.2 and requires a T6 Torx key. The cutter is configured for ADMX 0702 indexable inserts from Pramet, allowing quick replacement without complex realignment. Indexable inserts mean that when a cutting edge wears, the insert is rotated or replaced rather than remanufacturing the whole cutter — a workflow that reduces downtime and lowers lifetime costs. Clear torque and key specifications make maintenance tasks predictable and efficient. Application focus and measurable productivity benefits With a 90° cutting angle and four teeth, this screw-in cutter is optimised for square shoulders and face machining where dimensional accuracy is critical. The cutting height of 23 mm supports adequate chip load for stable material removal in short-reach setups. By combining a compact diameter with multi-edge cutting, the tool balances material removal rate with surface integrity, enabling faster cycle times on small-diameter features. For workshops seeking dependable, repeatable results in precision turning and facing, this configuration offers a reliable compromise between accessibility and cutting performance. For tailored procurement of the Teknik Cutting Tools screw-in milling cutter VT200TM with ADMX 0702 compatibility, contact Metav Werkzeuge for expert advice and reliable supply directly from Emmerich. Technical data SKU: VT200TM Name: Screw-in milling cutter for ADMX 0702 indexable inserts Brand: Teknik Makina ECLASS: 21180806 ETIM: EC011860 Facts Diameter: 16 mm Total length: 41 mm Thread: M8 Thread height: 18 mm Cutting height: 23 mm Number of cutting edges: 4 Cutting angle: 90° Weight: 0.041 kg Torx screw: M2x4.2 Torx key: T6 Special features Compatible with ADMX 0702 indexable inserts Designed for Pramet insert system Compact design for limited-access machining Balanced multi-edge geometry for stable cutting FAQ Which insert type fits this cutter? The cutter is configured for ADMX 0702 indexable inserts and is compatible with Pramet ADMX 0702 inserts as specified for the VT200TM. What is the mounting thread and screw specification? Mounting uses an M8 screw-in thread with 18 mm thread engagement; the clamping screw is M2x4.2 and the required Torx key is T6. What machining tasks is the cutter intended for? The 90° cutting geometry and four cutting edges make the tool suitable for square-shoulder cutting and facing in compact setups where rigidity and repeatability are required. How many cutting edges does the tool have and what is the benefit? The cutter has four cutting edges, which provide balanced material removal, lower vibration and improved surface quality for short-reach operations. What are the key dimensions that affect rigidity? Key dimensions are the 16 mm diameter, 41 mm total length and 0.041 kg mass; these combine to reduce overhang and improve stability during machining. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
16mm Screw-In Cutter 90° For APKT 1003 Indexable Inserts, M8 Thread - Teknik Makina
Take advantage of the combination of compact design, precise 90° cutting geometry and straightforward insert compatibility for consistent face-milling results; order directly via Metav Werkzeuge or consult their advisors for matching inserts and setup assistance. Screw-in Milling Cutter VT136TM — 90° shank cutter for APKT 1003 indexable inserts by Teknik Makina The Screw-in Milling Cutter VT136TM is a compact, 90° screw-in cutter intended for precision face milling and short overhang operations with Korloy APKT 1003 indexable inserts. 90° cutting angle for reliable face milling Compatible with Korloy APKT 1003 inserts M8 screw-in shank, Ø 16 mm Torx fastener M2.5x5.5, keyed with T8 High-precision mounting and stable tool geometry for repeatable results The VT136TM is engineered as a screw-in milling cutter with a screw-in shank (M8) and a compact diameter of Ø 16 mm, enabling a low overhang and predictable tool behaviour. Compatibility with Korloy APKT 1003 indexable inserts ensures that proven insert geometries are available for a wide range of face-milling tasks. The design reduces setup variability: the central threaded connection and clear reference surfaces permit consistent orientation, while the cutter’s defined 90° cutting angle produces square shoulders and accurate board finishes. This combination supports process stability in repeated cycles and simplifies tool selection in mixed-production environments. Rapid insert changes and secure clamping to reduce downtime The tool uses a single Torx fastener (size M2.5x5.5) tightened with a T8 key for insert clamping, which provides a straightforward and secure retention method. With 2 cutting edges and an overall length of 41 mm, the cutter is optimised for short, controlled engagements where fast indexable-insert replacement keeps cycle times low. The compact dimensions and low mass (approx. 0.05 kg) contribute to lower centrifugal loads and make it well suited to machines with limited tool magazine capacity. Where quick changeovers are required, the simple Torx fixation minimises handling time and the risk of incorrect seating. Practical applications and workshop benefits for everyday production This screw-in tool is intended for workshops and production lines that require accurate face milling with standard APKT 1003 inserts and a robust 90° geometry. The compact form factor supports tight set-ups and confined work envelopes, while the proven insert family from Korloy provides options for finishing and general-purpose cutting. For users seeking predictable results and reduced set-up complexity, the unitary screw-in mounting and standardised insert interface make tool management more efficient and less error-prone. If further clarification on fitting or suitable insert grades is needed, Metav’s technical advisors can be consulted for application-specific guidance. For delivery, technical matching and procurement of the Teknik Makina VT136TM screw-in milling cutter contact Metav Werkzeuge for supply and expert advice at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data SKU: VT136TM Manufacturer: Teknik Makina Facts Diameter: 16 mm Thread: M8 Thread height: 16 mm Cutting-edge height: 25 mm Cutting angle: 90° Number of cutting edges: 2 Overall length: 41 mm Weight: 0.05 kg Torx fastener: M2.5x5.5 Torx key: T8 Compatible inserts manufacturer: Korloy Special features Screw-in mounting Compatible with APKT 1003 indexable inserts Compact design for reduced overhang Torx-secured insert clamping FAQ Which inserts are compatible with this cutter? The cutter is compatible with Korloy APKT 1003 indexable inserts; the APKT family provides a range of grades for finishing and general-purpose milling. What is the required fastening tool for insert changes? Insert clamping is secured with a Torx fastener M2.5x5.5 and requires a T8 key for correct torque application. How does the cutter’s geometry affect machining? The 90° cutting angle creates square shoulders and precise face finishes; the compact Ø 16 mm body reduces overhang for improved rigidity during short engagements. Is the cutter suitable for automated tool magazines? With an overall length of 41 mm and a mass of approximately 0.05 kg, the design is compatible with many automatic tool-change systems and smaller tool magazines. What machine applications are recommended for this type of cutter? The tool is intended for face milling and short-reach operations in small to medium series production where standard APKT 1003 inserts deliver the required surface quality. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
16mm Screw-In Cutter for APMT 0903 Indexable Inserts L41mm With Internal Coolant, M08 Thread - Teknik Makina
Take advantage of the combination of precise compatibility with APMT 0903 indexable inserts, robust M08 thread mounting and internal coolant for longer tool life; order the cutter directly via Metav Werkzeuge or consult our specialists for application advice. Screw-in milling cutter VT224-1TM — 16 mm, internal coolant, for APMT 0903 indexable inserts (Teknik Makina) Screw-in milling cutter VT224-1TM for use with APMT 0903 indexable inserts, offering compact geometry and integrated coolant for stable milling performance in workshop and production settings. 16 mm diameter for compact machining Internal coolant supply to the cutting zone Compatible with Korloy APMT 0903 inserts Secure M08 thread mounting with Torx fastening Precision and rigidity that reduce rework The compact design combines a 16 mm diameter with an overall length 41 mm to offer a short overhang and improved stiffness during interrupted or light milling operations. The tool’s two cutting edges and a cutting-edge height of 25 mm provide consistent chip engagement and balanced cutting forces, which reduces vibration and the likelihood of rework. Integrated internal coolant directs fluid to the cutting zone, supporting improved tool life and more reliable surface finishes. These features translate directly into higher first-pass yield and fewer subsequent dressing or finishing operations. Quick insert changes and secure mounting for minimal downtime Designed for rapid serviceability, the cutter uses a standard M08 thread with a thread height of 16 mm to ensure positive seating and repeatable concentricity after tool changes. Insert retention is achieved with a Torx screw ( M2.5x5.5 ) requiring a Torx T8 key, enabling fast, safe replacement of inserts with minimal setup time. The lightweight construction (approx. 0.04 kg) eases handling and tool magazine management, while the simple fastening procedure helps to keep machine downtime to a minimum and increase overall equipment effectiveness. Compatibility and straightforward workshop integration The holder is made to accept APMT 0903 indexable inserts and is specified as compatible with Korloy inserts, making it easy to integrate into existing tooling inventories. The combination of internal coolant and compact geometry suits a wide range of milling tasks where APMT 0903 inserts are preferred, from semi-finish to finishing passes. Technical clarifications and application recommendations are available for those planning toolpath strategies or machine setup adjustments; practical guidance helps to align cutting parameters with the holder’s capabilities for efficient, predictable results. For availability, detailed application advice or to arrange supply of the VT224-1TM screw-in milling cutter with internal coolant, contact Metav Werkzeuge — reliable delivery from Emmerich and expert consultancy are available. Technical data Article number: VT224-1TM Label: 16mm Einschraubfräser APMT 0903 L41mm mit Innenkühlung Manufacturer: Teknik Makina SKU: VT224-1TM Core data Diameter: 16 mm Overall length: 41 mm Weight: 0.04 kg Thread: M08 Thread height: 16 mm Cutting edges: 2 Cutting-edge height: 25 mm Torx screw: M2.5x5.5 Torx key: T8 Special features Internal coolant supply For APMT 0903 indexable inserts Compatible with Korloy inserts Compact holder geometry FAQ Which inserts fit this cutter? The VT224-1TM accepts APMT 0903 indexable inserts and is specified as compatible with Korloy inserts. Is there internal coolant on the tool? Yes — the cutter provides internal coolant directed to the cutting zone to support tool life and improved surface quality. How is the cutter mounted? Mounting is via an M08 thread with a thread height of 16 mm; the insert is secured with an M2.5x5.5 Torx screw tightened using a Torx T8 key. How many cutting edges does the holder provide? The tool is equipped for two cutting edges, with a cutting-edge height of 25 mm, providing balanced engagement for stable machining. What are the identification and manufacturer details? The SKU is VT224-1TM and the tool is manufactured by Teknik Makina. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
16mm Screw-In Cutter for BLMP 0603 Indexable Inserts With Internal Cooling, M08 Thread - Teknik Makina
Reliable machining performance with internal coolant and compatibility for BLMP 0603 indexable inserts ensures efficient chip evacuation and consistent surface quality; order the screw-in milling cutter directly via Metav Werkzeuge or ask our consultants for application advice. Screw-in milling cutter VT190-1TM — 16 mm diameter, internal coolant (Teknik Makina) A Screw-in milling cutter VT190-1TM engineered for secure insert clamping and high-efficiency face and shoulder milling using BLMP 0603 indexable inserts. Internal coolant for stable cutting Compatible with BLMP 0603 inserts (Taegutec) Compact 16 mm diameter, L 41 mm Two cutting edges for smooth material removal Small-diameter performance with controlled cooling The compact design delivers focused cutting power in restricted workspaces while the internal coolant channel reduces heat at the cutting zone and improves tool life. With a 16 mm diameter and an overall length of 41 mm, the tool provides a rigid cutting geometry that helps maintain dimensional accuracy during face or shoulder milling. The combination of coolant-fed cutting and a short overhang reduces chatter and improves surface finish, translating into higher first-pass yields and fewer reworks. Fast insert changes and reliable clamping for uninterrupted machining Designed for BLMP 0603 indexable inserts, the cutter features secure fixation with an M3x6.2 Torx screw tightened using a Torx T8 key, enabling quick, repeatable insert changes. The thread-in connection (thread: M08) ensures stable mounting in compatible holders and simple tool replacement without the need for specialised adapters. With two cutting edges and a cutting-edge height of 25 mm, the assembly balances metal removal rates and chip control for many common milling tasks, supporting efficient shifts in batch production. Integration into workshop workflows and consistent quality delivery Lightweight at approximately 0.044 kg and compatible with inserts from Taegutec, the tool is suited to standard small-diameter milling applications where repeatability and uptime matter. The thread-in format simplifies inventory and toolholder management in production environments, while the coolant-fed design supports longer insert life and reduced thermal distortion. For procurement and planning, the SKU VT190-1TM allows straightforward ordering and stock tracking within a centralised tool management approach. For procurement or application support for the Teknik Makina screw-in milling cutter, contact Metav Werkzeuge in Emmerich for tailored advice and to arrange supply: info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: VT190-1TM Manufacturer: Teknik Makina Product type: Screw-in milling cutter Label: 16mm Einschraubfräser BLMP 0603 L41mm mit Innenkühlung Facts Diameter: 16 mm Overall length: 41 mm Thread height: 16 mm Thread: M08 Cutting edges: 2 Cutting height: 25 mm Weight: 0.044 kg Special features Internal coolant Compatible with BLMP 0603 indexable inserts Compatible insert manufacturer: Taegutec Torx screw: M3x6,2 Torx key: T8 FAQ What inserts fit this screw-in milling cutter? The tool is specified for BLMP 0603 indexable inserts, compatible with inserts from Taegutec for standard face and shoulder milling applications. Is the cutter coolant-fed and how does that benefit machining? Yes — the internal coolant channel supplies cutting fluid directly to the cutting zone, which reduces heat and improves insert life for the VT190-1TM screw-in milling cutter. What thread and mounting does the tool require? The cutter uses an M08 thread with a 16 mm thread height for secure mounting in suitable holders, enabling stable operation in demanding cycles. Manufacturer/Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
16mm Screw-In Cutter for EPMT 0603 Indexable Inserts L41mm With Internal Coolant, M08 Thread - Teknik Makina
Take advantage of a compact, high‑precision design that combines a 16 mm diameter, secure M08 screw‑in clamping and internal coolant for improved tool life and consistent cycle times; order directly via Metav Werkzeuge or consult our specialists for application advice. VT230-1TM screw-in cutter — for EPMT 0603 indexable inserts with internal coolant (Teknik Makina) The VT230-1TM screw-in cutter provides a compact, coolant-fed milling solution for operations that require quick insert changes and stable clamping in confined tool setups 16 mm diameter for compact machining Internal coolant for efficient chip removal M08 screw-in thread with 25 mm engagement Compatible with EPMT 0603 indexable inserts Consistent clamping for accurate finishes The combination of an M08 screw‑in interface and a long 25 mm engagement means the tool is designed for stable, repeatable clamping with minimal runout. A reduced radial overhang and a 16 mm body diameter contribute to lower vibration and improved surface quality, while the 2 cutting edges deliver balanced cutting forces for steady feed rates. This results in predictable tool behaviour that supports tighter tolerances and fewer reworks on batch production runs, translating directly into improved process reliability. Enhanced chip evacuation and coolant flow for longer runtimes Equipped with integrated internal coolant, the cutter directs cooling and lubrication precisely to the cutting zone, lowering temperatures and reducing built‑up edge formation. The tool accepts EPMT 0603 indexable inserts from Hitachi, allowing rapid insert replacement without compromising cutting geometry. Efficient coolant flow and focused chip control extend insert life and maintain consistent cutting performance, which helps to reduce downtime and the frequency of tool changes in medium‑ to high‑volume milling tasks. Service‑friendly design that suits busy workshop environments The compact overall length (L41 mm) and low mass (0.04 kg) make the tool simple to handle and less prone to accidental collisions in congested setups. Fast maintenance is supported by standard fastenings — Torx T8 drive and M2.5x5.5 Torx screw — enabling quick insert swaps with common workshop tools. The slim profile and straightforward assembly support efficient inventory management and minimise machine idle time, an advantage for operations aiming to maintain steady throughput without complex tool handling procedures. For specialist advice or immediate availability of the Teknik Makina VT230-1TM screw-in cutter with internal coolant, contact Metav Werkzeuge in Emmerich by e‑mail at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data SKU: VT230-1TM Manufacturer: Teknik Makina Product type: Screw-in cutter Facts Diameter: 16 mm Overall length: 41 mm Thread engagement height: 25 mm Thread: M08 Weight: 0.04 kg Cutting edges: 2 Cutting-edge height: 16 mm Features Internal coolant Compatible with EPMT 0603 indexable inserts Compatible insert manufacturer: Hitachi Torx key: T8 Torx screw: M2.5x5.5 FAQ Which inserts fit this cutter? The VT230-1TM is designed for EPMT 0603 indexable inserts; compatibility with Hitachi‑made inserts is specified for consistent seating and cutting geometry. Does the tool support internal coolant? Yes, the cutter is equipped with internal coolant, supplying the cutting edge directly to assist thermal control and chip evacuation. What fastener is required to change inserts? Insert retention uses an M2.5x5.5 Torx screw and a T8 Torx key for reliable clamping and simple servicing. Is this cutter suitable for confined toolholders? The compact 16 mm diameter and L41 mm overall length make the cutter suitable for applications with limited clearance or tight tool layouts. How many cutting edges does the tool have? The design features 2 cutting edges, providing balanced cutting forces and stable material removal. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com
Maximise reach and flexibility with screw-in cutters
Screw-in cutters, also known as modular screw-in milling heads or threaded cutter heads, are modular milling tools with a threaded rear that are screwed into extensions or basic toolholders. They allow the tool overhang to be adapted precisely to the depth of the machining area, providing the reach and adaptability required for complex tool and mould work.
Why these modular heads are essential in deep machining
Screw-in cutters are designed so that only the front milling head needs replacing when worn, while the carrier assemblies and extensions remain in service — a setup that reduces tooling costs and simplifies logistics in production environments. Versions without internal coolant rely on external nozzles to feed coolant to the cutting zone, which is adequate for shallow, easily accessible operations but becomes ineffective for deep contours. For deep internal work the industrial standard is screw-in cutters with internal coolant: inner channels run through the connection thread right to the cutting edges, ensuring centred coolant delivery, reliable chip transport and effective heat control.
- the internal coolant supply generates the high flushing pressure necessary to evacuate chips against gravity from narrow cavities
- thermal load on the concealed cutting zone is reduced, lowering the risk of thermal damage and deformation
- improved chip evacuation prevents spalling and vibration, dramatically reducing the likelihood of tool breakage during extended overhangs
Practical benefits that improve throughput and cost-efficiency
- replaceable milling heads cut tooling expenditure and inventory complexity
- modular carrier systems and extensions reduce retooling and shorten changeover times
- reliable chip evacuation and cooling increase tool life and process stability
- consistent performance for deep cavities minimises scrap and rework
Metav as your precision partner for modular tooling
As a specialist partner, Metav brings decades of expertise and a broad offering that suits industry and workshops alike. With over 48,000 customers and a catalogue spanning more than 250,000 products, Metav combines a pragmatic supply chain from Emmerich with technical competence that helps engineers specify the right screw-in cutters and supporting extensions. If you need advice on selecting a modular screw-in milling head or determining the correct internal coolant routing for a cavity, our technical team can advise on specifications and compatibility.
In short: screw-in cutters provide modular reach, cost-effective head replacement and indispensable internal coolant performance for deep, confined machining.
FAQ
What is the difference between screw-in cutters with internal coolant and those without?
Screw-in cutters with internal coolant feature internal channels that feed coolant directly to the cutting edges via the connection thread, providing the flushing pressure required to evacuate chips from deep cavities; cutters without internal coolant rely on external nozzles and are suitable only for shallow, easily accessible operations.
How do modular screw-in milling heads reduce tooling costs?
Because the design allows only the worn front milling head to be replaced while the carrier and extensions remain in use, modular screw-in milling heads lower component consumption and simplify inventory management, leading to clear cost savings over time.
Which machining scenarios require threaded cutter heads with internal coolant?
Threaded cutter heads with internal coolant are essential when machining deep bores, cavities or internal contours where chips must be transported out against gravity and where external coolant cannot reach the cutting zone reliably.
Can long extensions be used with screw-in cutters without compromising chip evacuation?
Long extensions are feasible, but reliable chip evacuation under long overhangs depends on internal coolant delivery; without it, external coolant will often be blocked by deep part walls and chip clogging becomes a significant risk.
Fragen zu diesen Produkten??
Mit mehr als 30 Jahren Erfahrung beraten wir Sie gerne persönlich.
Tel.: +49 2822 7131930
Mail: info@metav-werkzeuge.com