Gibt es einen Hahn und Kolb Online Shop?

Benefit from a compact, high-stability tool head that combines a 63 mm diameter and internal coolant with compatibility for WNMU 0706 indexable inserts; this arrangement delivers consistent edge life and reliable chip control. Order directly via Metav Werkzeuge or contact the consultants for specification matching and fast supply from Emmerich. Corner tool head — 63 mm, internal coolant (Teknik Makina) The corner tool head for WNMU 0706 indexable inserts provides a compact solution for precise shoulder and angle turning in coolant-fed machining environments. 63 mm head diameter for stable machining Internal coolant for improved chip evacuation Compatible with WNMU 0706 indexable inserts 90° cutting angle with six usable edges Increased process reliability through measurable stiffness The compact design with a 63 mm head diameter and an overall length of L40 mm gives a low overhang, which directly reduces vibration and improves surface finish. This geometry, together with the 90° cutting angle, enables repeatable shoulder and profile operations while maintaining tool life. For production environments that prioritise cycle-time consistency, the combination of reduced deflection and six usable cutting edges results in fewer tool changes and higher net productivity per insert. Optimised cooling and chip control for stable machining Equipped with internal coolant, the head channels cutting fluid close to the cutting zone to promote better heat dissipation and more reliable chip evacuation. This reduces thermal softening of the insert and the workpiece surface layer, especially during continuous or high-feed operations. Where process thermal stability matters, internal feed-through coolant supports longer insert life and fewer interruptions for manual cleaning, contributing to predictable machining windows and less scrap. Simple maintenance and broad compatibility for flexible tooling The head accepts WNMU 0706 indexable inserts and is compatible with Sumitomo-specified grades, allowing easy integration into existing tool sets. Fastening is via a Torx screw M5x12 (Torx key T20), so replacement is straightforward with common workshop tools. The compact assembly and standardised fixing mean shorter downtime during insert changes and uncomplicated inventory management for spare parts. The robust design also supports frequent use in mixed-production shops where quick tool swaps and compatibility with established insert systems are essential. For enquiry or to arrange immediate delivery from Metav Werkzeuge, request full specifications for the Teknik Makina corner tool head (SKU T316TM) and discuss suitability for specific materials and grades with our technical team Technical data SKU: T316TM Manufacturer: Teknik Makina Product type: Corner tool head Facts Diameter: 63 mm Overall length: 40 mm Cutting angle: 90° Number of usable cutting edges: 6 Torx screw: M5x12 Torx key: T20 Special features Internal coolant For WNMU 0706 indexable inserts Compatible with Sumitomo inserts Compact L40 mm design FAQ Which inserts fit this tool head? The corner tool head accepts WNMU 0706 indexable inserts; compatibility with Sumitomo-specified grades is indicated for the Teknik Makina T316TM. Is the head suitable for coolant-fed operations? Yes — the T316TM is equipped with internal coolant, designed to deliver fluid close to the cutting edge for improved heat control and chip evacuation. How many cutting edges can be used per insert position? The design supports six usable cutting edges on the inserts in the corner tool head, contributing to extended tool life and lower tooling costs. What fasteners are required for insert clamping? Insert clamping uses a Torx screw M5x12, tightened with a T20 Torx key for secure and repeatable clamping of the insert. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from the combination of a 63 mm tool body, a 90° cutting angle and integrated coolant for stable, repeatable turning operations; the compact 40 mm length and compatibility with WNMU 0807 indexable inserts (Sumitomo) ensure straightforward integration into existing tool assemblies. Order or discuss the item via Metav Werkzeuge for a reliable production upgrade. Corner turning head T297TM — 63 mm diameter, internal coolant (Teknik Makina) Corner turning head T297TM for WNMU 0807 indexable inserts, engineered for precision square-shoulder turning and robust external machining in CNC turning centres 63 mm diameter for stable machining Internal coolant for improved chip removal Compatible with WNMU 0807 Sumitomo inserts 90° cutting angle for square-shoulder turning Increased rigidity and repeatable geometry for cleaner finishes The robust tool body with a 63 mm diameter delivers higher stiffness, which reduces vibration during cutting and improves surface quality on the workpiece. Designed around a 90° cutting angle, the holder is optimised for square-shoulder and profiling operations where dimensional accuracy matters. The head accepts WNMU 0807 style indexable inserts, providing six cutting edges to extend usable life and lower tooling costs per part. This rigidity and defined geometry help maintain repeatable results across production runs, supporting consistent tolerance control and fewer reworks. Coolant-fed cutting zone for longer tool life and reliable chip control An integrated internal coolant channel directs fluid directly to the cutting edge, reducing temperature at the cutting zone and improving flank wear behaviour. The result is extended insert life and more stable cutting parameters when machining at higher feed rates. Compatibility with Sumitomo WNMU 0807 indexable inserts allows users to select grades tailored to the job, while the coolant-fed design assists chip evacuation and reduces built-up edge—advantages that translate into longer unattended cycle times and improved process security for batch production. Quick, secure clamping for efficient tool changes and shop-floor uptime The insert is fastened with an M5x12 Torx screw operated with a T20 key, enabling predictable torque and quick replacement under production conditions. With an overall length of 40 mm, the head is compact enough for tight-tooling envelopes yet long enough to provide stable support for the insert pocket. The combination of standardised fixing hardware and compact design minimises downtime during tool changes and simplifies spares handling in the tool crib, making the head suitable for both job shop and high-volume turning cells. Discuss your application with Metav Werkzeuge and secure the Teknik Makina T297TM corner turning head with internal coolant to improve process stability and cutting-edge performance on your CNC turning machines Technical data SKU: T297TM Product type: Eckmesserkopf Manufacturer: Teknik Makina ECLASS: 21181015 Dimensions & core data Diameter: 63 mm Overall length: 40 mm Cutting angle: 90° Cutting edges: 6 Screw: M5x12 Torx key: T20 Internal coolant: yes Special features Compatible with WNMU 0807 indexable inserts Designed for square-shoulder turning Coolant-fed insert pocket Standard Torx fastening for secure clamping Compact design for tight tooling envelopes FAQ Which insert type fits this tool head? The tool head accepts WNMU 0807 indexable inserts; it is supplied to work with Sumitomo-style inserts for a secure fit. Does the holder provide internal coolant? Yes — the T297TM features internal coolant that supplies fluid directly to the cutting zone. What are the key dimensions of the head? Diameter is 63 mm with an overall length of 40 mm, and the cutting geometry is 90°. How is the insert secured in the pocket? The insert is clamped using an M5x12 Torx screw tightened with a T20 key for repeatable fixation. For which operations is this head best suited? The head is optimised for square-shoulder turning and external turning tasks where rigidity, coolant supply and quick insert changes improve cycle stability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a combination of precise geometry and active cooling to maintain stable corner milling cycles; the compact 40 mm length and 63 mm diameter minimise overhang while the internal coolant supports chip control. Order the Tek​nik Makina cutting head directly via Metav Werkzeuge or ask our consultants for application support. Corner milling head T855-1TM — 63 mm, internal coolant, for XNKT 0604 indexable inserts (Teknik Makina) Corner milling head for XNKT 0604 indexable inserts designed for accurate corner machining with internal coolant and a 90° cutting angle 63 mm diameter for stable machining Internal coolant for enhanced cooling Fits XNKT 0604 indexable inserts (Korloy) Eight cutting edges and 90° cutting angle High stability and repeatable geometry for corner milling The corner milling head delivers consistent results through a compact design featuring a 63 mm diameter and total length 40 mm, which together reduce overhang and vibration during interrupted cuts. The arrangement of eight cutting edges and the 90° cutting angle provide predictable contact conditions at each index, supporting precise corner generation and repeatability on production runs. The relatively low mass (0.527 kg) aids dynamic stability without compromising rigidity. Fast insert changes and secure clamping for reliable production Clamping is executed with a Torx screw (M3x7) tightened with a T8 key, enabling secure, repeatable seating of XNKT-style inserts. Compatibility with XNKT 0604 indexable inserts — including those from Korloy — simplifies stock management and reduces tooling downtime by allowing common insert types to be used across multiple toolholders. The component’s identification T855-1TM helps streamline ordering and inventory tracking within a workshop environment. Improved cooling and chip control for demanding cycles Integrated internal coolant channels direct fluid close to the cutting edge, which improves heat evacuation and chip formation. This targeted cooling helps maintain cutting-edge integrity and surface finish during longer cycles, while reducing the frequency of unscheduled tool changes. The internal coolant feature is particularly beneficial when consistent machining parameters and thermal stability are priorities on medium- to high-volume turning or milling operations. Practical integration into the tooling system and workshop workflow Designed as a drop-in solution for corner operations, this tool head supports established indexable insert systems and simple maintenance routines, making it suitable for jobbing shops and production lines alike. The combination of established insert compatibility and a compact form factor makes the head an efficient choice for tasks where reliable corner accuracy and straightforward serviceability are required. The labelled SKU T855-1TM and robust fastening details aid clear documentation in tool libraries and CAM setups. For a tailored recommendation on using the Teknik Makina T855-1TM with Korloy XNKT 0604 inserts, please contact Metav Werkzeuge’s Emmerich team for application advice or to arrange supply from our local warehouse. Technical data Article number: T855-1TM Label: 63 mm corner milling head XNKT 0604 L40 mm with internal coolant Product type: Corner milling head Brand: Teknik Makina Core data Diameter: 63 mm Total length: 40 mm Weight: 0.527 kg Number of cutting edges: 8 Cutting angle: 90° Torx screw: M3x7 Torx key size: T8 Compatible inserts: XNKT 0604 Special features Internal coolant Compatible with Korloy XNKT 0604 indexable inserts Compact design for reduced overhang Robust Torx clamping system FAQ What insert type is required for this tool head? The corner milling head accepts XNKT 0604 indexable inserts; compatibility with Korloy inserts is specified for straightforward replacement. How is coolant supplied to the cutting edge? The tool head features internal coolant channels that deliver fluid close to the insert edge to improve cooling and chip control. Which fastener is used to secure the insert? Insert clamping is via a Torx screw (M3x7) that is tightened with a T8 Torx key for secure and repeatable fastening. Is the T855-1TM suitable for production runs with frequent indexing? Yes, the combination of eight cutting edges, secure Torx clamping and compact geometry supports frequent indexing and consistent performance in production environments. How should the tool be referenced in inventory and CAM systems? Use the SKU T855-1TM and the label “63 mm corner milling head XNKT 0604 L40 mm with internal coolant” to ensure clear identification across tooling lists and CAM libraries. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid 90° corner tool head with XNKT 0604 indexable insert compatibility and a 22 mm mounting shank for secure machine attachment — a pragmatic choice for stable turning operations; order the component directly via Metav Werkzeuge or consult the Metav team for machine-fit advice. Eckmesserkopf — 90° corner tool head for XNKT 0604 indexable inserts by Teknik Makina The Eckmesserkopf is a 90° corner turning head designed for external turning tasks that accept XNKT 0604 indexable inserts, combining a compact footprint with a robust Ø63 mm head diameter for improved cutting stability. 90° cutting angle for precise corner turning For XNKT 0604 indexable inserts Ø63 mm head with 22 mm mounting shank Torx M3x7 screw; T8 key size Precise corner turning without compromise A 90° cutting geometry delivers consistent, repeatable corner profiles while keeping the machining setup compact. The combination of a 90° cutting angle and support for XNKT 0604 indexable inserts provides a predictable cutting edge orientation, which simplifies programming and process planning. The head’s Ø63 mm diameter helps maintain rigidity during interrupted cuts, reducing chatter and improving surface finish. For users less familiar with insert codes: XNKT 0604 denotes a small, rectangular/triangular indexable insert format commonly used for fine external turning and profiling. Secure fastening and straightforward insert replacement Fast, reliable clamping is provided via the specified M3x7 Torx screw and the corresponding T8 key size, ensuring repeatable seating of the insert seat. The holder’s 22 mm mounting shank is intended for stable attachment to compatible tool posts or modular adaptors, reducing deflection under load and helping to extend insert life. Because the cutting edge is supplied by indexable inserts rather than a brazed tip, routine maintenance is limited to insert changes and a quick screw torque check, which keeps downtime and overall tooling costs low. Compatibility that eases tooling logistics This turning head is adapted to work with inserts from established manufacturers such as Korloy, making it straightforward to source replacement edges and standardise tooling across machine fleets. Standard insert formats reduce procurement complexity and allow workshops to consolidate stock. The head’s compatibility with XNKT 0604 inserts supports a range of external turning and profiling tasks while maintaining interchangeability between holders and cutters. Compact design that supports shopfloor flexibility With an overall length of 40 mm and a mass of 0.527 kg, the unit is compact enough for constrained setups while offering the mass required to dampen vibration in many turning operations. The modest footprint and standardised mounting diameter enable installation on smaller lathes or multi-axis turning centres where space and accessibility are limited. This balance of rigidity and compactness helps achieve consistent parts quality in high-mix, low-volume production and in specialised machining cells. Contact Metav Werkzeuge for a compatibility check and supply from Emmerich — Metav Werkzeuge offers tailored advice for machine fit and fast delivery from its European warehouse, e‑mail info@metav-werkzeuge.com or phone +49 2822 7131930 Technical data Article number: T855TM Name: Eckmesserkopf for XNKT 0604 indexable inserts Manufacturer: Teknik Makina Key dimensions Head diameter: 63 mm Mounting shank: 22 mm Overall length: 40 mm Weight: 0.527 kg Cutting angle: 90° Number of cutting edges: 8 Features Torx screw: M3x7 Torx key size: T8 Compatible insert manufacturer: Korloy Suitable for: XNKT 0604 indexable inserts eClass: 21180902 Files (refs): 62de7efb0aced56449540edd, 62de7dc7bd24461b3d5f79f5 FAQ What insert type does this turning head accept? The turning head accepts XNKT 0604 indexable inserts, a compact format suitable for precise external turning and profiling. Is the holder compatible with Korloy inserts? Yes — the head is specified as compatible with inserts from Korloy, simplifying sourcing of replacement edges. What mounting diameter is required for the holder? The holder is designed for a 22 mm mounting shank, suitable for tool posts and adaptors that accept that diameter. Which screw and key size secure the insert? Insert clamping uses an M3x7 Torx screw and requires a T8 key size for tightening. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the precise 90° cutting geometry and integrated internal coolant to improve cycle stability and tool life; the robust 63 mm head, compatible with XNKT 0805 indexable inserts, supports efficient chip evacuation and repeatable shoulder machining. Order the component directly via Metav Werkzeuge or consult our specialists for application advice. Corner cutter head (Eckmesserkopf) T904-1TM — 63 mm, internal coolant (Teknik Makina) Corner cutter head (Eckmesserkopf) T904-1TM for XNKT 0805 indexable inserts, designed for shoulder and face operations where a compact, coolant-fed solution is required 63 mm diameter head Internal coolant feed Compatible with XNKT 0805 inserts 90° cutting angle, six cutting edges Accurate geometry for consistent shoulder machining The head delivers a stable 90° cutting geometry that simplifies square shoulder and face finishing. By combining a compact 63 mm diameter with a total length of 45 mm, the assembly minimises overhang while maintaining rigidity, which reduces vibration and improves surface quality. The compatibility with XNKT 0805 inserts—common in many production environments—ensures reproducible cutting edges for batch production, while the mass of 0.575 kg contributes to steady dynamic behaviour on the toolpost or turret. Integrated coolant for longer tool life and better chip control Built-in internal coolant directs fluid directly to the cutting zone, supporting effective chip evacuation and temperature control during high-material-removal operations. The result is prolonged insert life and fewer unplanned tool changes, which raises machine uptime and lowers unit cost per part. The clamping hardware uses T15 Torx for secure fixing and M4x10 screws for reliable retention, enabling straightforward maintenance and rapid insert changes during shift work. Designed for flexible workshop use and proven compatibility This cutter head accepts XNKT 0805 inserts from established suppliers such as Korloy, providing broad availability and selection of grades for steel, stainless, and non-ferrous applications. The design, with six effective cutting edges and a robust body manufacture, supports both finishing and light roughing operations where repeatability is essential. For teams evaluating tooling strategies, the compact design balances accessibility with mechanical stiffness, making it suitable for series parts and repair jobs alike. Contact Metav Werkzeuge for tailored advice on integrating the Teknik Makina corner cutter head into production and to request detailed application data — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 Technical data SKU: T904-1TM Manufacturer: Teknik Makina Product type: Corner cutter head Compatible inserts: XNKT 0805 Compatible insert brand: Korloy Internal coolant: Yes Total length: 45 mm Diameter: 63 mm Weight: 0.575 kg Cutting edges: 6 Cutting angle: 90° Torx key: T15 Screw: M4x10 eClass: 21181015 Facts Diameter: 63 mm Length: 45 mm Weight: 0.575 kg Cutting angle: 90° Cutting edges: 6 Screw size: M4x10 Torx: T15 Special features Internal coolant feed Compatible with XNKT 0805 inserts Robust body for reduced vibration Quick insert replacement with Torx fixation Suitable for shoulder and face operations FAQ What inserts fit this cutter head? The corner cutter head accepts XNKT 0805 indexable inserts; grades from Korloy are commonly used for a range of materials. Does the head provide coolant to the cutting zone? Yes, the T904-1TM features internal coolant to improve chip removal and thermal control at the cutting edge. Which screw and key are required for maintenance? Retention is secured with M4x10 screws and a T15 Torx key for stable clamping and quick insert changes. Is the head suitable for finishing and light roughing? The combination of 90° cutting geometry and a compact 63 mm diameter makes it appropriate for finishing and moderate roughing tasks where rigidity is needed. What are the physical dimensions and weight? Total length is 45 mm, diameter 63 mm, and the component weighs 0.575 kg, supporting a compact, stiff setup. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from compact stability and targeted cooling: the combination of a 63 mm diameter body and internal coolant delivers steady, repeatable corner turning for tight-tolerance work. Compatible with XOMX 1204 indexable inserts and supplied under SKU T514-1TM, this solution is available directly from Metav Werkzeuge or via consultation with our specialists. Corner tool head for XOMX 1204 indexable inserts — 63 mm, internal coolant (Teknik Makina) The Corner tool head is a compact angle turning head developed for XOMX 1204 indexable inserts, offering internal coolant supply for controlled chip evacuation and consistent cutting conditions. 63 mm diameter for stable machining Internal coolant for improved chip control Accepts XOMX 1204 indexable inserts Robust construction, weight 0.618 kg Stable cutting results where space is limited Engineered for operations that demand precise cornering, the tool head’s 63 mm diameter provides a rigid mounting platform that reduces vibration and improves surface finish. Designed to accept XOMX 1204 indexable inserts, the holder supports repeatable index changes and predictable tool life. The combination of a compact body and six cutting positions means frequent insert rotations are possible without the need for multiple toolholders, improving uptime and reducing set‑up frequency. For machinists working to tight tolerances, the resulting stability translates directly into higher first-pass yield and less rework. Controlled cooling for longer tool life and consistent chip flow The integrated internal coolant channel delivers lubricant and cooling directly to the cutting edge, helping to control temperatures and flush chips away from the cutting zone. This focused coolant delivery reduces thermal wear and decreases the risk of built-up edge on inserts, which supports longer insert life and more consistent cycle times. Maintenance is straightforward: the clamping screw and assembly are fastened with a T10 Torx drive and the replacement screw specification is M3.5x8.5, enabling quick, toolroom‑standard servicing during scheduled tool changes. Quick setup and predictable repeatability With a compact 40 mm overall length and a manageable mass of 0.618 kg, the holder balances rigidity with ease of handling during toolset changes. The design is compatible with insert standards from SECO, ensuring broad availability of cutting grades and geometries for different materials. The 90° cutting angle offers straightforward geometry for common turning and profiling tasks, and the six available cutting edges reduce tooling costs by extending the usable life per insert. For production environments, this combination simplifies inventory and keeps changeover times low. Suited applications and productivity improvements The angle head is particularly effective in finishing and semi‑finishing passes on components where corner accuracy and surface integrity are critical. It is suitable for general turning tasks where a compact head is required on multi‑tool turrets or tight work envelopes on CNC lathes. By pairing the holder with optimised insert grades, workshops can achieve measurable productivity gains through fewer tool swaps and improved process stability. The compact format also aids access in complex set‑ups, minimising the need for extended overhangs that can compromise tool life. For tailored application advice and reliable supply from Metav Werkzeuge, request the Teknik Makina corner tool head (SKU T514-1TM) with internal coolant via eMail or telephone and receive guidance specific to the intended material and machine set‑up. Technical data Article number: T514-1TM UID: T514-1TM ECLASS: 21181015 Facts Diameter: 63 mm Overall length: 40 mm Weight: 0.618 kg Cutting angle: 90° Number of cutting edges: 6 Special features Internal coolant For XOMX 1204 indexable inserts Compatible with SECO inserts Torx key: T10 Torx screw: M3.5x8.5 Product type: Corner tool head Manufacturer: Teknik Makina Label: 63mm Eckmesserkopf XOMX 1204 L40mm mit Innenkühlung FAQ Which insert series fits this holder? The holder accepts XOMX 1204 indexable inserts; insert compatibility includes variants supplied by SECO and equivalents conforming to that geometry. Is the coolant internal or external? This model provides internal coolant, delivering lubricant directly to the cutting edge for improved chip evacuation and thermal control. What fastening tools are required for maintenance? Assembly and replacement use a T10 Torx drive; the clamping screw specification is M3.5x8.5 for straightforward servicing. Can this head be used for finishing passes on small components? Yes; the compact 40 mm overall length and 63 mm body support rigid mounting for finishing and semi‑finishing operations in confined work envelopes. What is the SKU for ordering and reference? Reference SKU T514-1TM when enquiring or ordering to ensure the correct Teknik Makina corner tool head is supplied. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the combination of robust rigidity, internal coolant and proven compatibility with LNMX 1510 indexable inserts for reliable turning operations; order the part via Metav Werkzeuge or consult our specialists for application guidance. Corner tool head for LNMX 1510 indexable inserts — 63 mm, internal coolant | Teknik Makina Corner tool head for LNMX 1510 indexable inserts offers a compact, coolant-fed solution for precision turning and facing operations where insert interchangeability and chip control are priorities 63 mm diameter for increased stability Internal coolant for improved chip evacuation Designed for LNMX 1510 indexable inserts Compact 45 mm overall length for close-profile work Compatible with Korloy insert grades and T15 fastening Higher process stability through robust geometry The corner tool head provides a 63 mm diameter body and a 90° cutting angle, delivering a stable toolholder interface that reduces vibration and improves surface finish. The head is configured for LNMX 1510 indexable inserts, a commonly used insert geometry for medium-duty turning, which simplifies stocking and replacement. Fastening uses a Torx T15 key and M4x12.5 screw, enabling secure, repeatable clamping; these standardised fittings reduce setup time and support consistent cutting performance across shifts. Coolant-fed design that extends tool life and improves cycle times An integrated internal coolant channel supplies cutting fluid directly to the cutting edge, enhancing cooling and chip evacuation at the point of contact. This targeted coolant delivery helps to lower cutting temperatures and evacuate chips more efficiently, which can prolong insert life and reduce the frequency of tool changes. The head’s 45 mm overall length and mass of 0.616 kg contribute to a compact, rigid package suited to operations where tool projection must be minimised while maintaining stiffness for reliable machining. Compatibility, maintenance and application scope Engineered for use with LNMX 1510 indexable inserts and compatible with Korloy insert variants, the head supports quick insert changes and straightforward maintenance. The design accommodates multiple insert edges before indexing, helping to reduce tooling costs over time. The standard Torx T15 interface and supplied screw size simplify replacement procedures and allow modern workshops to maintain fast tool-change routines. For applications demanding predictable performance in general turning and profiling, this indexable head is a pragmatic choice that balances compactness with coolant capability. For coolant-critical turning tasks, secure the Teknik Makina 63 mm corner tool head (SKU T374-1TM) through Metav Werkzeuge and arrange an application review with our consultants to ensure optimal insertion and coolant strategy Technical data Article number: T374-1TM ECLASS: 21181015 Label: 63mm Eckmesserkopf LNMX 1510 L45mm mit Innenkühlung Manufacturer: Teknik Makina UID: T374-1TM Facts Diameter: 63 mm Overall length: 45 mm Weight: 0.616 kg Cutting angle: 90° Number of cutting edges: 6 Torx key: T15 Torx screw: M4x12.5 Special features Internal coolant channel For LNMX 1510 indexable inserts Compatible with Korloy insert grades Product type: Corner tool head Brand: Teknik Makina FAQ Which insert type does this tool accept? The corner tool head is designed for LNMX 1510 indexable inserts, ensuring compatibility with standard LNMX geometries and facilitating straightforward insert replacement. Is internal coolant routed directly to the insert? Yes; the head features internal coolant that directs fluid towards the cutting edge to assist cooling and chip removal during machining. What fastening hardware is required for insert retention? Insert clamping uses a Torx T15 key and an M4x12.5 screw, providing secure and repeatable retention for the insert pocket. Can this head work with Korloy inserts? The component is specified as compatible with Korloy inserts for the LNMX 1510 geometry, allowing use of common Korloy grades where appropriate. Is the tool suitable for close-proximity machining? With a 45 mm overall length and a compact, rigid body, the head suits operations requiring limited projection and enhanced stability. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Choose the combination of a 90° cutting geometry, a sturdy 63 mm head and a standard 27 mm shank for reliable shoulder turning — order the T643TM directly via Metav Werkzeuge or request advice from our technical consultants. Corner turning head T643TM by Teknik Makina — 90° head for ANHX 1206 indexable inserts, 63 mm diameter Corner turning head T643TM is a compact turning head designed for shoulder and profile turning with ANHX 1206 indexable inserts; suitable where repeatable right‑angle cuts and stable clamping are required 90° cutting angle for shoulder turning 63 mm head diameter for stability 27 mm shank diameter for standard holders Compatible with ANHX 1206 Palbit inserts Consistent shoulder turning with defined 90° geometry The T643TM has a precisely machined 90° cutting angle, which provides a predictable shoulder finish and reduces the need for secondary operations. The defined angle simplifies set‑up on the lathe and helps maintain part tolerances across batches. Thanks to the 63 mm head diameter, radial stiffness is increased, reducing chatter and improving surface quality during transverse cuts. Fast insert changes and secure clamping for production environments A single Torx M3.5x8.5 fixing screw (Torx key T15) secures the insert, enabling quick index changes and short tool‑down times. The design supports ANHX 1206 indexable inserts from Palbit, ensuring a wide choice of grades for roughing and finishing. The combination of positive clamping and an accessible screw position reduces the likelihood of incorrect seating, so set‑up remains efficient even in mixed‑operator workshops. Compact dimensions with industrial compatibility With a 27 mm shank diameter and a total length of 40 mm, the holder suits standard tool posts and indexable systems, allowing straightforward integration into existing tool stations. The compact footprint makes it suitable for confined turret spaces while the head diameter balances rigidity with access to tight features. The unit weight of 0.619 kg contributes to stable dynamic behaviour without overloading the turret. Designed for reliable batch production Five cutting edges and a robust body geometry support repeatable performance in short to medium production runs. The construction and choice of fixing hardware prioritise uptime: fewer interventions, consistent insert orientation and dependable torque on the Torx screw. For operations where predictable cycle times and surface results matter, this tool head offers a pragmatic combination of rigidity and serviceability. For procurement or technical clarifications regarding the Teknik Makina T643TM corner turning head, contact Metav Werkzeuge for tailored recommendations and delivery from our Emmerich stock. Technical Data Article number: T643TM Manufacturer: Teknik Makina Product name: Eckmesserkopf for ANHX 1206 indexable inserts Brand: Teknik Makina Facts Head diameter: 63 mm Shank diameter (take‑up): 27 mm Cutting angle: 90° Total length: 40 mm Weight: 0.619 kg Number of cutting edges: 5 Special features Torx screw: M3.5x8.5 Torx key size: T15 Compatible inserts: ANHX 1206 (Palbit) Application: shoulder/corner turning SKU: T643TM FAQ Which indexable inserts fit this head? The head accepts ANHX 1206 indexable inserts; Palbit grades are compatible and commonly used with the T643TM for a range of steel and cast iron operations. What is the shank size required in the tool post? The T643TM requires a 27 mm take‑up or bore in the toolholder, matching standard 27 mm shank tool posts. Is the fixing screw and key included? The unit is specified with a Torx screw M3.5x8.5 and uses a T15 key for clamping; check the product contents at time of order for delivery scope. Which operations is this head best suited to? The turning head is optimised for 90° shoulder and profile turning, offering good rigidity for transverse cuts and repeatable part faces. Can the head be used for finishing as well as roughing? Yes — by selecting the appropriate ANHX 1206 insert grade, the T643TM can be set up for both roughing and finishing passes while maintaining consistent results. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Optimise machining productivity with a compact milling head that combines precise RDMT 1204 insert compatibility and six indexed cutting edges for efficient material removal; its Torx fixation simplifies insert changes and reduces downtime. Order the round insert milling cutter directly via Metav Werkzeuge or ask our consultants if needed. Round Insert Milling Cutter for RDMT 1204 indexable inserts, Ø 63 mm, L 40 mm — Teknik Makina The Round Insert Milling Cutter is a compact milling head designed for general milling tasks that use RDMT 1204 indexable inserts, delivering fast indexability and consistent cutting performance in confined set-ups. Ø 63 mm compact cutter, L 40 mm Compatible with RDMT 1204 indexable inserts Six indexed cutting edges for efficient machining Torx T15 fixation with M3.5x8.5 screws Faster cycle times through precise insert seating The tool is engineered for repeatable seating of RDMT 1204 indexable inserts, which means every index or replacement restores the original cutting geometry without lengthy regrinding. With six cutting edges available on the head, tool life is effectively extended by distributing wear across multiple edges; this reduces the frequency of tool changes and supports higher material removal rates. The design targets rational productivity gains, favouring predictable machining cycles and easier process planning. Reduced maintenance and secure clamping for reliable shifts Fast, tool-free insert changes are supported by a Torx system that ensures consistent torque and secure screw retention. The Torx T15 interface together with M3.5x8.5 screws enables repeatable clamping force, helping to avoid micro-movements that cause premature wear or poor surface finish. Routine maintenance is straightforward: indexed inserts rotate to a fresh edge, and the fastening system requires only a single Torx key for both inspection and replacement, reducing non-productive time on the shop floor. Compact form factor for flexible machine integration With a nominal diameter of Ø 63 mm and overall length L 40 mm, the cutter fits machines and fixtures where space is limited, without compromising on cutting capacity. The compact footprint supports close-tool positioning and multi-head arrangements, enabling denser tool layouts in turret-style or gantry setups. This balance of small form factor and multi-edge indexing delivers an economical way to increase throughput while maintaining modest spindle load and good chip evacuation. Industrial reliability with clear traceability Supplied by Teknik Makina, the milling head combines familiar indexable-insert standards with industrial-grade manufacturing, offering a straightforward replacement strategy for existing RDMT 1204 tool families. The product's concise specification and SKU allow for clear inventory control and quick procurement, supporting lean stock management. Its measured mass and geometry contribute to stable run-out characteristics, aiding repeatable finishing and semi-finishing operations across production batches. Contact Metav Werkzeuge for tailored application advice and to secure the Teknik Makina round insert milling cutter compatible with RDMT 1204 indexable inserts; our Emmerich team is available by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical data Article number: T142TM SKU: T142TM Manufacturer: Teknik Makina Label: 63mm Rundplattenfräser RDMT 1204 L40mm ECLASS: 21180902 Core specifications Diameter: 63 mm Overall length: 40 mm Weight: 0.512 kg Cutting edges: 6 Materials / Features Compatible with RDMT 1204 indexable inserts Torx T15 fixation Torx screw M3.5x8.5 Product type: Round insert milling cutter Category: Planing cutter head FAQ Is this cutter compatible with RDMT 1204 inserts? Yes. The round insert milling cutter is designed specifically for RDMT 1204 indexable inserts and secures them for repeatable cutting geometry. How many cutting edges are available per head? The milling head offers six indexed cutting edges, allowing wear to be distributed across multiple edges for longer service intervals. Which fastening system is used for the inserts? Inserts are secured using a Torx T15 interface with M3.5x8.5 screws to ensure consistent clamping and simple replacement procedures. Can the cutter be used in compact machine setups? Yes. With a diameter of Ø 63 mm and length L 40 mm, the cutter is suitable for tight tool arrangements and compact fixture designs. What is the SKU and mass for inventory purposes? The SKU is T142TM and the weight is 0.512 kg, useful for stock control and handling calculations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Taking advantage of a compact 45 mm overall length and a 22 mm shank for secure fixture, this tool head provides a stable 90° cutting geometry that supports repeatable external turning with APKT 1604 indexable inserts; order via Metav Werkzeuge or contact our advisers for fitment guidance. Corner Tool Head T185TM — Corner turning head for APKT 1604 indexable inserts, 90° cutting angle (Teknik Cutting Tools) The Corner Tool Head T185TM is designed for external turning operations using APKT 1604 indexable inserts and offers a compact, rigid configuration for workshop and production environments. Compact 45 mm overall length for tight access Secure M4x10 Torx fastening, T15 key Compatible with Korloy APKT 1604 inserts 22 mm shank for stable mounting Rigidity and repeatability for accurate external turning A robust 22 mm shank combined with the 90° cutting angle provides a rigid mounting platform that reduces deflection and improves dimensional repeatability during external turning operations. The mass and geometry of the head are tuned to deliver stable cutting behaviour, which helps to maintain tool life and workpiece quality over series runs. Engineers benefit from consistent results when machining shoulders and faces because the head’s construction limits vibration and supports predictable tool engagement. Fast insert changes and standardised retention Compatibility with APKT 1604 indexable inserts—including those from Korloy—means insert selection is straightforward and tooling costs can be optimised through widely available grades. The insert is secured with an M4x10 Torx screw, tightened with a T15 key, enabling fast, repeatable clamping and minimal downtime for index changes. This standardised retention reduces maintenance complexity on the shop floor and keeps changeover times low in high-mix environments. Compact form factor for accessibility and balance With a 45 mm overall length and 63 mm diameter, the head presents a compact profile that improves accessibility in confined turning setups while offering sufficient mass (approx. 0.578 kg) for damping cutting forces. The relatively short overhang helps when working close to fixtures or when multiple operations are staged on a single spindle. The head’s design supports stable cutting across common turning tasks and simplifies integration into existing tool posts and holders with 22 mm mounting interfaces. For tailored advice or to arrange supply through Metav Werkzeuge, please contact our technical team in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930; our advisers can confirm compatibility and delivery options for the T185TM corner tool head. Technical data Article number: T185TM Manufacturer: Teknik Makina Product name: Corner tool head (Eckmesserkopf) For indexable inserts: APKT 1604 Facts Diameter: 63 mm Overall length: 45 mm Shank diameter (D): 22 mm Weight: 0.578 kg Cutting angle: 90° Number of cutting edges: 6 Special features For APKT 1604 indexable inserts Compatible with Korloy inserts M4x10 Torx screw retention Torx key size: T15 Compact design for confined machining FAQ Which inserts fit this tool head? The T185TM accepts APKT 1604 indexable inserts; compatibility with Korloy inserts is indicated in the product data. What fastening hardware is used to secure the insert? Insert retention is by an M4x10 Torx screw, tightened with a T15 key as specified for the Corner Tool Head T185TM. What shank size is required for mounting? The tool head uses a 22 mm mounting diameter (shank) for secure installation in compatible holders. Is the head suitable for tight access applications? Yes, the compact 45 mm overall length and 63 mm diameter were chosen to improve accessibility while maintaining stability during turning. How does the T185TM contribute to machining repeatability? The combination of a 22 mm shank, 90° cutting geometry and a robust clamping system reduces deflection and supports consistent dimensional results during series turning operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Eckmesserkopf für SPMT 1204 Wendeplatten (T651-1TM) Der Eckmesserkopf ist ein Präzisionswerkzeug für die Zerspanung, optimiert für den Einsatz mit SPMT 1204 Wendeplatten und für hohe Standzeiten bei Serienfertigung ausgelegt Kompatibel mit SPMT 1204 Wendeplatten Innenkühlung reduziert Werkzeugtemperatur Durchmesser 63 mm für stabile Aufnahme Gesamtlänge 50 mm für Serienbearbeitung Befestigung mit Torx Schlüssel T20 und M5x12 Schraube Höhere Standzeit durch integrierte Innenkühlung Die Innenkühlung des Werkzeugs leitet Kühlschmierstoff direkt an die Schneidkante, sodass die Temperatur während der Bearbeitung deutlich sinkt und sich die Standzeit der Wendeplatten verlängert. Diese direkte Kühlung verbessert die Spanabfuhr und reduziert thermische Belastung, was besonders bei Dauerläufen in der Serienfertigung zu weniger Stillstandzeiten führt. Durch die gezielte Kühlung bleibt die Schnittqualität konstant und Nachbearbeitung wird minimiert Stabile Aufnahme für präzise Ergebnisse Die Kombination aus Durchmesser 63 mm und Aufnahme Ø 22 mm sorgt für eine formstabile Verbindung zwischen Werkzeug und Halter. Der definierte Schnittwinkel von 90° gewährleistet reproduzierbare Schnittbedingungen und gleichmäßige Oberflächen. Weniger Vibrationen bedeuten geringeren Werkzeugverschleiß und konstante Maßhaltigkeit bei wiederholten Bearbeitungsschritten, was die Prozesssicherheit in Fertigungslinien erhöht Einfache Montage und sichere Befestigung Die Montage erfolgt mit dem mitgelisteten Torx Schlüssel T20 und einer Torx Schraube M5x12, wodurch ein schneller Wechsel der Wendeplatten möglich ist. Die Befestigungstechnik reduziert Montagezeiten und ermöglicht einen werkstattgerechten Umgang bei Wartung oder Umrüstungen. Klare Schraubvorgaben und zugängliche Schraubenpositionen vereinfachen die Handhabung auch unter beengten Platzverhältnissen Effizient in der Serienbearbeitung dank durchdachter Geometrie Mit Gesamtlänge 50 mm und fünf Schneiden ist das Werkzeug auf kontinuierliche Bearbeitung ausgelegt und bietet wirtschaftliche Laufzeiten bei hohen Stückzahlen. Die Geometrie ist so gewählt, dass sie Spanvolumen und Schnittkräfte optimal verteilt, was die Performance bei kontinuierlichem Vorschub stabilisiert. Dadurch sinken Stillstandsrisiko und Werkzeugkosten pro Bauteil in der Fertigung Empfehlung: Für konstant präzise Zerspanung auf Serienmaschinen empfiehlt sich der Einsatz des robusten Eckmesserkopfs von Teknik Makina; für technische Beratung und Bestellung steht Metav Werkzeuge per eMail info@metav-werkzeuge.com oder Telefon +49 2822 7131930 zur Verfügung Produktmerkmale Artikelnummer: T651-1TM Marke: Teknik Makina Bezeichnung: Eckmesserkopf für SPMT 1204 Wendeplatten Daten Durchmesser: 63 mm Gesamtlänge: 50 mm Aufnahme Durchmesser: 22 mm Schneiden: 5 Schnittwinkel: 90 ° Gewicht: 0.772 kg Besonderheiten Innenkühlung (kanalisiert, direkter Kühlmittelzufluss) Torx Schlüssel: T20 Torx Schraube: M5x12 Passend für Wendeplatten: SPMT 1204 SKU: T651-1TM FAQ Ist der Eckmesserkopf mit SPMT 1204 Wendeplatten kompatibel? Der Eckmesserkopf T651-1TM von Teknik Makina ist speziell für SPMT 1204 Wendeplatten ausgelegt und ermöglicht sicheren Sitz sowie zuverlässige Schnittbedingungen mit dieser Plattengeneration. Wie verbessert die Innenkühlung die Standzeit? Die integrierte Innenkühlung des Eckmesserkopfs leitet Kühlschmierstoff direkt an die Schneidkante, reduziert Wärmeentwicklung und verbessert die Spanabfuhr, wodurch die Belagsbildung minimiert und die Standzeit der Wendeplatten erhöht wird. Welche Werkzeuge werden für die Montage benötigt? Für die Befestigung sind Torx Schlüssel T20 und die Torx Schraube M5x12 vorgesehen; mit diesen Komponenten lässt sich der Eckmesserkopf schnell und sicher montieren oder umrüsten. Eignet sich das Werkzeug für Serienfertigung? Der Eckmesserkopf T651-1TM wurde für den Dauerbetrieb konzipiert: fünf Schneiden und die stabile Geometrie reduzieren Stillstandzeiten und senken die Kosten pro bearbeitetes Bauteil. Welche Schnittgeometrie liefert konstante Oberflächen? Der definierte Schnittwinkel von 90° in Kombination mit dem Durchmesser von 63 mm sorgt für gleichmäßige Schnitte und reproduzierbare Oberflächen bei wiederholten Bearbeitungszyklen. Hersteller: Teknik Makina, Nolu Sokak, No 9, Selcuklu, Türkei, eMail: info@teknik-makina.com / Verantwortlich: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from precise material removal and reliable cooling: the 63 mm diameter mill with internal through‑coolant and five cutting edges delivers consistent face milling performance. Order the cutter directly via Metav Werkzeuge or contact the consultants for application advice. Round face mill T273-1TM – 63 mm diameter, internal coolant (Teknik Makina) The Round face mill is a compact milling head designed for efficient face milling with RDMT 1604 indexable inserts in industrial machining environments 63 mm diameter for wide face milling Internal through-coolant for chip evacuation Compatible with RDMT 1604 indexable inserts Five cutting edges for stable material removal Robust design, overall length 45 mm Faster cycles and extended tool life through active cooling The combination of 63 mm diameter and internal coolant improves heat control at the cutting zone, which reduces thermal wear and helps maintain cutting geometry over long cycles. For shops aiming to increase throughput, the integrated coolant channel supports uninterrupted machining and contributes to longer insert life, lowering replacement frequency and improving overall machining economy. The design supports consistent surface quality when running continuous face‑milling passes. Stable cutting and predictable chip control with five edges Equipped with five cutting edges, the milling head distributes cutting forces evenly across the tool body, reducing vibration and promoting a more stable cut. The assembly uses M4x10 screws with a T15 Torx drive for secure seat retention, simplifying reindexing and maintenance. The stable platform enabled by this configuration is suited to repeatable production runs where dimensional consistency and toolpath predictability are priorities. Quick setup and durable construction for daily workshop use Compatibility with RDMT 1604 indexable inserts allows rapid tool changes and standardised inventory management. With an overall length of 45 mm and a compact mass of 0.512 kg, the cutter is straightforward to handle during setup while still offering the rigidity expected in production environments. The item is supplied under SKU T273-1TM by Teknik Makina, making it a practical choice for operations seeking a balance of performance and straightforward maintenance. Contact Metav Werkzeuge for tailored application recommendations and order the Teknik Makina round face mill T273-1TM with internal coolant for improved machining throughput and reliability Technical data SKU: T273-1TM Manufacturer: Teknik Makina Product type: Round face mill Label: 63mm Rundplattenfräser RDMT 1604 L45mm mit Innenkühlung Facts Diameter: 63 mm Overall length: 45 mm Cutting edges: 5 Weight: 0.512 kg Screw: M4x10 Special features Compatible with RDMT 1604 indexable inserts Internal through-coolant Torx key: T15 Category: Planmesserkopf eClass: 21180902 FAQ Which inserts fit this milling head? The milling head accepts RDMT 1604 indexable inserts; compatibility is specified for the T273-1TM model by Teknik Makina Does the cutter support through‑coolant operation? Yes, the tool features internal coolant to feed cutting zones directly for improved cooling and chip evacuation during continuous machining What fastening hardware is required for insert mounting? Insert clamping uses M4x10 screws with a T15 Torx drive as supplied for secure retention Is the tool suitable for high‑volume production? Designed for repeatable face milling duties, the compact construction and coolant provision make the cutter appropriate for continuous production applications What is the product identifier for ordering and stock checks? Reference SKU T273-1TM when enquiring about the round face mill from Teknik Makina Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of a 63 mm cutting diameter, internal coolant and compatibility with XNMX 0606 inserts for consistent, high-volume stock removal; order the face milling head directly via Metav Werkzeuge or consult our specialists for selection and delivery. Face milling head T736TM – 63 mm diameter with internal coolant (Teknik Cutting Tools) Face milling head T736TM for precision roughing and semi-finishing with XNMX 0606 indexable inserts, designed for stable, high-performance milling in workshop and industrial environments 63 mm diameter for robust material removal Internal coolant for improved chip evacuation Compatible with XNMX 0606 Korloy indexable inserts Six cutting edges; secure M4x12.5 Torx screws High removal rates with controlled engagement The 63 mm cutter body combined with six cutting edges offers a high material removal rate while maintaining cutting stability. The specified 51° cutting angle reduces cutting forces and distributes load across the inserts, which improves surface quality during roughing. As a result, the tool provides predictable tool paths and consistent cycle times on castings, steel and alloy components. This balanced geometry helps maintain spindle load within expected limits and supports efficient machining strategies. Reliable cooling and maintenance-friendly design Built-in internal coolant channels direct cutting fluid to the insert seat, improving chip evacuation and heat dissipation at the cutting edge. The secure clamping arrangement uses M4x12.5 Torx screws with a T15 key drive, enabling quick insert changes and reproducible torque application. The compact 40 mm overall length offers access in tighter setups while still allowing adequate coolant flow; routine maintenance and insert replacement remain straightforward and fast, reducing downtime on the shop floor. Broad compatibility and production continuity Engineered for use with XNMX 0606 indexable inserts and optimised for inserts from Korloy, this cutter head supports a wide range of cutting grades and geometries for different materials and operations. Manufactured by Teknik Cutting Tools, the component is suitable for both small jobbing shops and industrial production lines that require dependable supply and consistent performance. Combined with Metav Werkzeuge’s distribution and quality oversight, the assembly ensures traceable sourcing and availability for replacement parts. For tailored technical advice or reliable supply of this face milling head from Teknik Cutting Tools, contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or call +49 2822 7131930 to discuss suitability and lead times Technical data Article number: T736TM Label: 63mm Planmesserkopf XNMX 0606 L40mm mit Innenkühlung Manufacturer: Teknik Makina Facts Diameter: 63 mm Overall length: 40 mm Shank bore / reception diameter: 22 mm Cutting edges: 6 Cutting angle: 51° Suitable inserts: XNMX 0606 Special features Internal coolant Compatible insert manufacturer: Korloy Torx key size: T15 Torx screws: M4x12.5 Product type: face milling head FAQ Which inserts fit this cutter head? The face milling head T736TM is designed for XNMX 0606 indexable inserts and is supplied to work reliably with Korloy insert geometries. Is internal coolant available on this model? Yes, this cutter head features internal coolant channels to improve chip evacuation and thermal control at the cutting edge. What drive and screws are required for insert clamping? Insert clamping uses M4x12.5 Torx screws with a T15 drive for secure, repeatable tightening. For what applications is this cutter head intended? The cutter head is suitable for roughing and semi-finishing operations where stable material removal and good chip control are required. What is the overall length and reception diameter? Overall length is 40 mm and the reception (shank bore) diameter is 22 mm, enabling compact setups and good accessibility. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 55° cutting geometry and secure Torx clamping for steady material removal and predictable tool behaviour; the compact ø63 mm head with a 22 mm shank offers a rigid interface for short overhangs. Order this milling head via Metav Werkzeuge or consult the specialists for compatibility and delivery. Planmesserkopf 55° – face milling head by Teknik Makina for HNHX 1006 indexable inserts, ø63 mm, 5 cutting edges The Planmesserkopf is a 55° face milling head engineered for use with Taegutec HNHX 1006 indexable inserts, providing a compact solution for precision facing and planing operations. 55° cutting angle for stable cutting Compatible with Taegutec HNHX 1006 inserts 63 mm head diameter, 5 cutting edges 22 mm shank diameter with M5x12 Torx screw T20 Increased material removal with controlled entry angle The 55° cutter geometry delivers a balance between axial engagement and radial load, enabling smoother chip formation and reduced vibration during facing operations. By combining a 55° cutting angle with an optimised head diameter, the tool reduces impact at each insert entry, which supports a consistent surface finish and extends insert life. For workshops seeking reliable cycle times, this orientation promotes higher effective feed per tooth without compromising stability. Rigid connection and straightforward insert fixing A 22 mm shank interface and a compact overall length ensure minimal deflection under load; the short overhang supported by the 50 mm total length increases stiffness at the cutting zone. The inserts are secured by an M5x12 Torx screw (Torx key T20), allowing reproducible clamping force and quick service intervals. The assembly weight of 0.675 kg contributes to controlled handling on the toolholder while maintaining robust contact with the spindle, so set-ups remain efficient and predictable in production. Designed for indexable inserts and industrial use Specified for use with Taegutec HNHX 1006 indexable inserts, the head accepts standard insert geometry for facing tasks and is suitable where a 55° approach angle is required. The 63 mm head diameter and five cutting edges make it well suited to operations that demand short to medium-length passes and consistent radial engagement. Selection of the appropriate HNHX 1006 grade determines performance for different materials, so the head functions as a versatile carrier for tailored insert choices in diverse machining scenarios. Contact Metav Werkzeuge for tailored advice on Teknik Makina face milling heads and secure delivery from Emmerich – eMail info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T470TM Manufacturer: Teknik Makina Suitable for indexable inserts: Taegutec HNHX 1006 Torx screw: M5x12 Torx key: T20 Dimensions & core data Head diameter: 63 mm Shank diameter: 22 mm Overall length: 50 mm Number of cutting edges: 5 Cutting angle: 55° Weight: 0.675 kg Special features For HNHX 1006 indexable inserts Planing/face milling head design Quick clamping with Torx screw SKU: T470TM FAQ What inserts fit this milling head? The milling head is designed for Taegutec HNHX 1006 indexable inserts, enabling straightforward use of those standard insert sizes. Which toolholder interface is required? A 22 mm shank diameter (aufnahme 22 mm) is provided; the head mounts where a 22 mm interface is supported. How are the inserts secured? Inserts are clamped with an M5x12 Torx screw and tightened using a T20 Torx key for consistent, repeatable fixing. Is this head suitable for long overhangs? The head’s compact overall length of 50 mm and the 22 mm shank are optimised for short to medium overhangs to maintain stiffness and reduce deflection. What are the main handling characteristics in the workshop? The unit’s weight of 0.675 kg and standard Torx clamping provide easy handling and quick insert changes while preserving rigid contact at the spindle. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust milling solution that combines a 100° cutting angle with compatibility for ENMX 0905 indexable inserts to ensure stable face milling and fewer tool changes; order supply and technical advice via Metav Werkzeuge for dependable delivery from Emmerich. Face milling head T702TM by Teknik Makina (for 100° ENMX 0905 indexable inserts) A face milling head designed for precision face milling with 100° cutting angle, compatible with ENMX 0905 indexable inserts and built for reliable workshop integration. 100° cutting angle for stable face milling Fits ENMX 0905 inserts (YG‑1 compatible) 63 mm diameter with 22 mm shank Torx T10 fastening, M3.5x8.5 screw Consistent surface quality through controlled geometry The milling head's defining geometry—notably the 100° cutting angle—delivers controlled chip flow and reduced vibration during facing operations, which leads to a more consistent surface finish and fewer rejects. Paired with the standard ENMX 0905 insert pocket, the tool provides a predictable cutting condition across repeated cycles; this stability is especially valuable for batch production where reproducibility matters. The design reduces the need for repeated set‑ups, which in turn saves machine time and supports higher overall throughput. Fast, secure insert clamping reduces downtime Fast maintenance and reliable clamping are central to sustained productivity. The head uses a Torx T10 interface and M3.5x8.5 fixing screw for each insert pocket, enabling quick insert changes with standard workshop tools and consistent torque application. With five cutting edges distributed across the insert geometry, tool life is optimised through usable indexing, so fewer inserts are consumed per production run. The combination of positive clamping and indexed insert life reduces unplanned stoppages and keeps machining cycles running smoothly. Built for easy integration with common toolholders Dimensionally, the component is suited to compact face milling set‑ups: a 63 mm external diameter and a 22 mm shank diameter support straightforward mounting in compatible holders. The overall height of 50 mm ensures a low overhang for improved rigidity. Because the head accepts ENMX 0905 inserts from established suppliers such as YG‑1, it integrates with widely available inserts and grades, simplifying stocking and procurement. This compatibility helps consolidate tooling portfolios and reduces supplier complexity while maintaining machining performance. Contact Metav Werkzeuge in Emmerich for ordering and application advice on the Teknik Makina face milling head T702TM — email info@metav-werkzeuge.com or call +49 2822 7131930 to discuss compatibility and delivery from our European stock Technical Data Article number: T702TM Type: Face milling head Designation: for 100° ENMX 0905 indexable inserts Brand: Teknik Makina Facts Diameter: 63 mm Overall height: 50 mm Shank diameter (d): 22 mm Cutting angle: 100° Number of cutting edges: 5 Special features Compatible inserts: ENMX 0905 Compatible insert manufacturer: YG‑1 Torx key size: T10 Fixing screw: M3.5x8.5 Suitable for face milling operations FAQ How does the 100° cutting angle affect facing performance? The 100° cutting angle on the face milling head reduces axial force and improves chip breaking during facing, which produces a steadier cut and more uniform surface finish when using ENMX 0905 inserts. Which inserts fit the milling head? The milling head accepts ENMX 0905 indexable inserts; compatible grades from manufacturers such as YG‑1 can be used for varied material applications and optimised cutting data. What are the key mounting dimensions to check before purchase? Check the head diameter of 63 mm, overall height of 50 mm and 22 mm shank diameter to ensure compatibility with the intended toolholder and to maintain rigidity in the setup. Can the insert be changed with common workshop tools? Yes, inserts are secured with a Torx T10 interface and a M3.5x8.5 screw, allowing quick changes with standard Torx drivers and consistent clamping torque. Is this head suitable for batch production environments? The combination of stable cutting geometry, indexed insert life and simple clamping makes this head well suited for repetitive facing tasks in batch production where uptime and reproducibility are priorities. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Precise machining and secure mounting combine in this compact face milling solution: compatibility with LOGU 0303 indexable inserts, a Ø63 mm head and a 22 mm shank bore deliver stable cutting performance and easy integration into standard toolholders. Order the face milling head T734TM directly via Metav Werkzeuge or ask our consultants if needed. Face milling head T734TM — for LOGU 0303 indexable inserts, Ø63 mm | Teknik Makina The face milling head T734TM is a compact milling cutter head engineered for robust face milling tasks with LOGU 0303 indexable inserts in industrial milling setups. Compatible with LOGU 0303 indexable inserts Ø63 mm head diameter for broad cutting paths 22 mm shank bore for rigid mounting Torx T15 retention with M3x7 screw Consistent, accurate face milling for production workflows The cutter head is designed to translate insert geometry into a reliable production result: by accepting LOGU 0303 indexable inserts the head keeps chip control and cutting geometry consistent across tool changes, which supports reproducible surface quality and reduced rework. The 22 mm shank bore improves rigidity in the toolholder, limiting deflection under load and enabling higher material removal rates without sacrificing dimensional stability. This performance-oriented configuration suits batch production where process repeatability matters. Quick insert changes and secure fixation to reduce downtime Fast, straightforward insert replacement is enabled by the Torx retention system: a Torx T15 driver and M3x7 screw secure each insert position firmly while allowing rapid service intervals. The head provides 9 cutting positions, which allows rotation or replacement with minimal intervention and keeps machine idle time to a minimum. Reliable clamping geometry maintains the correct cutting angle after each change, so cycle time savings are realised without compromising tool life or component finish. Compact dimensions and workshop integration for smooth installation With a Ø63 mm head diameter and 50 mm overall height the unit fits into many standard setups while offering a wide cutting path for efficient face milling. Compatibility with Kyocera LOGU 0303 inserts ensures access to a broad range of grades and edge geometries for specific materials. The compact footprint supports close clearance operations and simple tool balancing, making the head suitable for high-throughput shops that require dependable, repeatable performance within constrained machine envelopes. Request a technical consultation from Metav Werkzeuge to specify the right Teknik Makina face milling head T734TM for the application and secure fast delivery from Emmerich — email info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T734TM Name: Planmesserkopf English designation: for LOGU 0303 Indexable Inserts Manufacturer: Teknik Makina Core dimensions Diameter: 63 mm Overall height: 50 mm Shank bore: 22 mm Cutting positions: 9 Torx key: T15 Torx screw: M3x7 Special features For LOGU 0303 indexable inserts Compatible with Kyocera inserts Retention with Torx T15 and M3x7 screw Ø63 mm head with compact 50 mm height FAQ Which inserts fit this milling head? The face milling head T734TM accepts LOGU 0303 indexable inserts and is compatible with Kyocera LOGU 0303 grades. How are inserts secured on the head? Inserts are retained with a Torx T15 screw (M3x7) on the Teknik Makina face milling head T734TM for secure fixation and quick replacement. What are the critical dimensions for toolholder compatibility? Key dimensions are a Ø63 mm head diameter, 50 mm overall height and a 22 mm shank bore; these determine mounting and clearance for the T734TM. How many cutting positions does the head provide? The head provides nine cutting positions, allowing rotation or replacement of insert edges to extend service life and reduce downtime. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Data inconsistency: the item is listed as compatible with PNMU 1206 indexable inserts in the article description, while the insert specification indicates PNMU 1006. This discrepancy creates confusion and could lead to potential issues for customers or users relying on accurate product information. Please confirm the correct insert designation so a complete product description can be prepared, ensuring clarity and avoiding any misunderstandings or errors in the future. Accurate and consistent data is essential for maintaining trust and ensuring that the product meets the needs and expectations of its intended users, so your prompt clarification would be greatly appreciated.

Benefit from a robust combination of stable clamping, a 45° cutting angle and a compact 63 mm head that delivers predictable flat finishes; order the planing cutter head directly via Metav Werkzeuge or request specialist advice from our consultants. Planing cutter head T165TM — compact head for SNEU 1206 indexable inserts, 63 mm diameter The Planing cutter head T165TM is a compact cutting-head engineered for precision face-planing operations with SNEU 1206 indexable inserts. 63 mm head diameter for rigid cutting Compatible with SNEU 1206 indexable inserts 45° cutting angle for flat finishes 22 mm shank for secure clamping Predictable surface quality from optimised geometry The head’s 45° cutting angle and defined geometry produce controlled chip formation and a consistent finish on planed faces. A tilted cutting geometry reduces vibration and spreads cutting forces over the insert edge, which helps maintain dimensional stability during pass-by-pass machining. For workshops seeking repeatable flatness and surface consistency, this configuration translates directly into shorter setup times and fewer reworks. Secure mounting and straightforward insert changes A 22 mm shank and a 63 mm head diameter create a steady support for the toolholder, reducing deflection under load. Insert retention is by an M5x12 Torx screw with a T20 key, allowing quick and secure indexing without specialized tooling. The combination of a compact overall length of 40 mm and a known fastener standard simplifies handling at the bench and speeds up maintenance cycles, improving uptime in production environments. Built for continuous productivity with multiple cutting edges Equipped to accept SNEU 1206 indexable inserts, the head design offers six cutting edges, which provides multiple usable cutting positions before replacement. This reduces stoppages for tool change and contributes to a lower cost-per-cut in repetitive operations. Compatibility with a widely used insert format makes the head suitable for mixed-production shops where flexibility and fast turnaround are essential. Suitable for workshops that value straightforward specifications The T165TM’s clear, measurable features — 63 mm diameter, 40 mm overall length, and 0.582 kg weight — make it simple to plan for clearances, spindle reach and tool balancing. These objective values support deterministic setup planning: they help to avoid surprises at the machine and to integrate the cutter head into existing tool lists without trial-and-error. Technical teams benefit from this clarity when compiling tool assemblies and defining process windows. Contact Metav Werkzeuge for tailored advice on Teknik Cutting Tools’ T165TM and secure prompt delivery from Emmerich — eMail: info@metav-werkzeuge.com or call +49 2822 7131930 Technical Data Article number: T165TM Name: Planing cutter head Manufacturer: Teknik Makina Suitable for: SNEU 1206 indexable inserts Data Diameter: 63 mm Overall length: 40 mm Shank diameter: 22 mm Cutting angle: 45° Cutting edges: 6 Weight: 0.582 kg Special features Torx screw: M5x12 Torx key size: T20 EClass: 21181015 SKU: T165TM FAQ What insert type is recommended for this cutter head? The planing cutter head accepts SNEU 1206 indexable inserts, which are specified for the T165TM and provide multiple usable edges. How is the insert secured in the head? Inserts are clamped with an M5x12 Torx screw; a T20 key is used for tightening and indexing on the T165TM. Which shank diameter is required for mounting? A 22 mm shank is specified for the toolholder interface and ensures a secure fit and low deflection in use. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high‑precision cutter head that combines a 45° cutting angle with compatibility for SNKX 1206 indexable inserts, delivering smooth finishing and predictable tool life; order directly via Metav Werkzeuge or consult the technical team for application matching. Face milling head T322TM by Teknik Makina — compact cutter for SNKX 1206 indexable inserts, 45° cutting angle The Face milling head T322TM is a compact cutter designed for light face milling and finishing operations using SNKX 1206 indexable inserts. 45° cutting angle for smooth finishing Compatible with SNKX 1206 indexable inserts 63 mm body diameter, Ø max cutting 76 mm Solid 22 mm shank for stable clamping Improved surface quality with predictable cutting forces The inclined 45° cutting angle reduces axial shock and spreads cutting forces over the insert, which results in a finer surface finish and more consistent tool life. As a result, the cutter head is particularly suitable where dimensional consistency and surface integrity matter; choosing an assembly built for SNKX‑type inserts ensures easy indexability and swift re‑clamping. The geometry is optimised for finishing passes, so cycle times can be shortened by taking slightly deeper but smoother cuts, while the insert‑based concept keeps consumable costs controllable. Robust geometry for repeatable set‑ups and quick maintenance A compact body with a 63 mm diameter and a 22 mm shank provides rigid support for short overhangs and repeatable set‑ups on standard toolholders. The tool’s overall length (44 mm) and modest mass (0.71 kg) reduce toolholder imbalance and vibrational tendencies in light‑duty milling. Fixing is achieved with a Torx screw M4x12.5 (Torx key T15), enabling rapid insert changes and secure clamping with common workshop tools. The head accommodates six cutting positions, so indexable inserts can be rotated or replaced with minimal downtime, supporting steady production throughput. Practical fitment and reliable supply chain for workshop use Engineered to accept SNKX 1206 inserts and compatible with insert ranges from Böhlerit, Korloy and Palbit, this cutter head is suited to mixed‑material workshops that favour indexable tooling for economical finishing. The combination of a standardised insert interface and a compact head reduces stocking complexity and simplifies supplier management. Metav Werkzeuge’s position as a precision partner ensures consistent availability and a quality filter for the European market, which helps maintain uninterrupted production planning and predictable lead times. For an application check, compatibility confirmation or delivery options, contact Metav Werkzeuge — the specialists in Emmerich who make precision tools accessible for every workshop Technical data Article number: T322TM Designation: Face milling head (Planmesserkopf) For inserts: SNKX 1206 Indexable Inserts Manufacturer: Teknik Makina Dimensions & core values Body diameter: 63 mm Max cutting diameter: 76 mm Shank diameter (d): 22 mm Total length: 44 mm Weight: 0.71 kg Cutting angle: 45° Number of cutting edges: 6 Fixings & compatibility Torx screw: M4x12.5 Torx key: T15 Compatible insert manufacturers: Böhlerit; Korloy; Palbit Suitable for SNKX 1206 indexable inserts FAQ Which inserts fit this milling head? The face milling head T322TM is designed for SNKX 1206 indexable inserts and is compatible with insert ranges from Böhlerit, Korloy and Palbit. How many cutting positions does the cutter head offer? The milling head provides six cutting positions, enabling multiple indexes per insert before replacement. What are the main dimensions affecting holder selection? Key dimensions are a 22 mm shank diameter and a 63 mm body diameter; the overall length is 44 mm and the maximum cutting diameter is 76 mm. Which screw and tool are required for insert changes? Insert fastening uses an M4x12.5 Torx screw and a T15 Torx key for secure and fast maintenance. For which operations is this head primarily intended? The T322TM cutter head is optimised for light face milling and finishing passes where a 45° cutting angle supports a high‑quality surface finish. Teknik Makina: Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Technical Specifications: Order Number: T574TM Item: Face Mill usable with ANKX 125 Indexable Inserts of ISCAR Brand: Teknik Makina Quantitative Specifications: Diameter: 63mm Cutting Edges: 6 Weight: 0.596kg Total length: 45mm Diameter Connection: 22mm Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Comprehensive Technical Specifications: Item: Face Mill Brand: Teknik Makina Order Number: T958TM usable with LNGU 15T6 Indexable Inserts the Hersteller's Kennametal Diameter: 63mm Angle: 90° Total length: 40mm Diameter Connection: 22mm Cutting Edges: 6 Weight: 0.541kg Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Product Technical Specifications: Order Number: T539TM Item: Face Mill usable with BDMT 1704 Indexable Inserts of Kyocera Brand: Teknik Makina Metric Information: Diameter: 63mm Cutting Edges: 6 Weight: 0.516kg Total length: 40mm Diameter Connection: 22mm Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Technical Information: Order Number: T624TM Item: Face Mill usable with SNKX 1206 Indexable Inserts of Palbit Brand: Teknik Makina Numbers and Data: Diameter: 63mm Cutting Edges: 6 Weight: 0.608kg Total length: 40mm Diameter Connection: 22mm Manufacturer Teknik Makina, Nolu Sokak, No 9, Selcuklu, Turkey, eMail: info@teknik-makina.com Responsible for Europe Metav Werkzeuge GmbH, Parkring 45, 46446 Emmerich, Germany, eMail: info@metav-werkzeuge.com

Combine compact size, secure Torx clamping and compatibility with standard RCKT 1204 indexable inserts to reduce changeover time and ensure consistent finishing. Order directly via Metav Werkzeuge or consult their specialists for application and mounting advice. Round Insert Milling Cutter T462TM — 63 mm diameter for RCKT 1204 indexable inserts (Teknik Makina) The Round Insert Milling Cutter T462TM is a compact indexable-insert milling head engineered for finishing and light face milling, designed to accept RCKT 1204 inserts and fit standard 22 mm toolholders. 63 mm cutting diameter for compact milling Accepts RCKT 1204 indexable inserts 22 mm mounting bore for standard toolholders Secured with M3.5x8.5 Torx screws (T15) Precise finishing in tight spaces The compact 63 mm diameter and relatively short overall length deliver stable finishing where larger heads cannot be used. With 5 cutting edges arranged for continuous material engagement, the cutter offers consistent surface quality without excessive axial overhang. The head’s 22 mm mounting bore and 40 mm overall length make integration into existing setups straightforward, reducing the need for dedicated adaptors. Using indexable inserts simplifies maintenance: individual edges are replaced rather than the whole tool, lowering per-cutting-costs while keeping machine downtime to a minimum. Fast, secure insert changes for higher uptime Tool changes are designed with workshop efficiency in mind. The inserts are clamped with M3.5x8.5 Torx screws and require a T15 key, providing repeatable clamping torque and quick replacement. Compatibility with Sandvik RCKT 1204 insert geometries ensures access to a wide range of carbide grades and chipbreakers for specific finishing tasks. This approach reduces set-up time and supports rapid grade swaps for different materials, making the cutter a practical choice for mixed-production environments where speed and repeatability matter. Built for reliable, everyday production At a weight of 0.436 kg, the milling head balances rigidity with low centrifugal loading, which helps maintain concentricity during high-speed rotation. The design focuses on robust seating and simple assembly to keep vibration low and insert life predictable. Where shorter tool projection and compact tooling are required, this cutter keeps the machining envelope tight and the production process stable. Technical documentation and compatibility details are documented for planning tool lists and ensuring seamless procurement. For consistent finishing in compact setups, contact Metav Werkzeuge to discuss the Teknik Makina T462TM, confirm holder compatibility and arrange supply directly from Emmerich Technical Data Article number: T462TM Manufacturer: Teknik Makina Designation: Round insert milling cutter for RCKT 1204 indexable inserts Facts Diameter: 63 mm Number of cutting edges: 5 Mounting bore: 22 mm Overall length: 40 mm Weight: 0.436 kg Special features Compatible inserts: Sandvik RCKT 1204 Torx screw: M3.5x8.5 Torx key: T15 eClass: 21180902 ETIM: EC011860 FAQ Which inserts fit this cutter most reliably? The T462TM is designed for RCKT 1204 indexable inserts; Sandvik variants to that specification are suitable and commonly used. What is the mounting diameter required? Mounting is via a 22 mm bore, suitable for standard toolholders that accept that shank size. How many cutting edges are fitted? The cutter carries 5 cutting edges, arranged to provide steady material removal and a fine surface finish. Which screw and key are needed for insert changes? Insert retention uses M3.5x8.5 Torx screws and is tightened with a T15 key for reliable clamping. Is the cutter suitable for finishing operations in compact setups? Yes; with a 63 mm diameter and compact overall length, the T462TM is intended for light face milling and finishing where space is limited. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com