Gibt es einen Hahn und Kolb Online Shop?

Take advantage of a robust combination of precise square‑shoulder machining, broad compatibility with XNEX 0806 indexable inserts, and simple serviceability for a steady production flow. Order or request guidance directly via Metav Werkzeuge to ensure the component fits the intended toolholder and shortens setup times. Corner Insert Head T844TM — 90° cutting angle, Ø80 mm — Teknik Makina The Corner Insert Head T844TM is a compact indexable insert holder designed for square‑shoulder turning and shoulder finishing in CNC turning centres 90° cutting angle for precise square turning Ø80 mm head diameter for increased rigidity Compatible with XNEX 0806 indexable inserts Torx M4x12.5 screw with T15 key for secure clamping Achieve consistently accurate square shoulders with rigid support The T844TM corner insert head is engineered for repeatable square‑shoulder machining by combining a 90° cutting angle with an Ø80 mm head diameter, offering a stable cutting geometry that reduces chatter and deflection. The holder’s shank diameter 27 mm and compact overall length 50 mm contribute to a stiff assembly that maintains dimensional tolerances across batches. Such mechanical stability improves first‑pass yield and reduces finishing operations, delivering measurable productivity gains for medium‑duty turning applications. Broad compatibility reduces inventory complexity and downtime Designed for use with XNEX 0806 indexable inserts, the head accepts inserts from major manufacturers including SECO and WINSTAR, which simplifies supply chain management and gives flexibility when sourcing cutting edges. Fast, tool‑room maintenance is supported by the Torx M4x12.5 fixing screw and the matching T15 key, enabling quick insert changes and reliable clamping torque. The result is shorter tool change intervals, fewer stoppages and a lower total cost of ownership for production lines that handle varied batches. Performance characteristics that support efficient shop workflows With seven cutting edges allocated across its geometry, the turner benefits from efficient load distribution and predictable wear behaviour, which extends effective cutting time between edge changes. The holder’s mass (approximately 1.063 kg) and balanced design help maintain spindle stability at typical turning speeds, while the square‑angled configuration is ideally suited to shoulder finishing, profiling and precision line turning. These attributes translate directly into consistent surface finish and reduced scrap rates for precision‑sensitive components. Simple installation and clear specifications for integration Installation requires only a T15 Torx key to secure the M4x12.5 fixing screw, and the Ø27 mm mounting diameter fits compact toolposts and modular carriers designed for small to medium‑sized lathes. The T844TM designation and clear dimensional data make it straightforward to confirm compatibility with existing toolholders and adapters. For operations upgrading to indexable tooling, the head provides a compact, reliable option that balances rigidity and accessibility, supporting both batch production and bespoke machining tasks. For tailored advice on integrating the Teknik Cutting Tools T844TM corner insert head into existing toolholder systems, contact Metav Werkzeuge in Emmerich by email at info@metav-werkzeuge.com or by phone on +49 2822 7131930 — the team will assist with compatibility checks, supply options and efficient implementation. Technical Data SKU: T844TM Name: Corner insert head for XNEX 0806 indexable inserts Brand: Teknik Makina Fixing screw: Torx M4x12.5 Torx key: T15 Facts Diameter: 80 mm Shank diameter (d): 27 mm Overall length: 50 mm Cutting angle: 90° Cutting edges: 7 Weight: 1.063 kg Special features Compatible with XNEX 0806 indexable inserts Suitable for inserts from SECO and WINSTAR Torx M4x12.5 fixing screw Torx key size T15 SKU T844TM Manufacturer: Teknik Cutting Tools FAQ What inserts are compatible with this head? The corner insert head accepts XNEX 0806 indexable inserts and is compatible with inserts from SECO and WINSTAR, enabling straightforward sourcing of cutting edges. Is the head suitable for square‑shoulder finishing? Yes. The 90° cutting angle and Ø80 mm head diameter make the component specifically suitable for precise square‑shoulder turning and shoulder finishing operations. Which fixing hardware is required for insert clamping? Clamping is performed with a Torx M4x12.5 screw using a T15 key, facilitating quick and secure insert changes. What are the mounting dimensions needed for toolholder integration? The head requires a 27 mm mounting diameter and an overall length of 50 mm, making it compatible with compact toolholders and modular carriers designed for medium‑duty turning. How does the design influence machining stability? The combination of a rigid Ø80 mm head, compact length and balanced mass (≈1.063 kg) reduces deflection and vibration, improving dimensional stability and surface finish during turning. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, rigid toolhead with a 90° cutting angle and compatibility with ANKX 0706 indexable inserts; its robust Ø80 mm head and M5x12 Torx fastening ensure stable corner turning and easy insert replacement — order via Metav Werkzeuge or consult their specialists for application advice. Angle Turning Head T446TM — 90° tool head for ANKX 0706 indexable inserts by Teknik Makina The Angle Turning Head T446TM is a purpose-built corner turning toolhead for CNC lathes and turning centres, engineered to accept ANKX 0706 indexable inserts and deliver reliable 90° shoulder and profile turning in a compact form. 90° cutting angle for precise corner turning Compatible with ANKX 0706 indexable inserts Torx M5x12 fastening, T20 key required Robust Ø80 mm head, 1.238 kg mass Achieve accurate corner turning with a defined 90° geometry The head’s 90° cutting angle provides a predictable cutting geometry for shoulder, profiling and facing operations. By accepting standard ANKX 0706 indexable inserts, the holder allows quick insert changes and consistent results across production runs. The defined geometry reduces setup variables and supports repeatable axial positioning, which improves machining accuracy and lowers scrap rates. For shops moving between roughing and finishing passes, the stable angle facilitates predictable tool engagement and surface finish control. Secure clamping and vibration-resistant design for stable machining A secure fastening system based on Torx M5x12 screws (drive size T20) holds the insert assembly firmly, while the 27 mm shank interface ensures correct seat in compatible toolholders. The combination of a solid connection and a substantial Ø80 mm head mass (approx. 1.238 kg) increases damping during cutting, reducing chatter on medium-duty lathes and turning centres. This stability translates into longer insert life and fewer rework cycles — a direct efficiency gain for batch production or single-part setups. Flexible operations and straightforward maintenance for workshop efficiency The compact 52 mm overall length and provision for six cutting edges allow for compact toolpaths without sacrificing insert capacity, making the head suitable for confined turrets and multi-axis configurations. The design focuses on quick insert replacement and low downtime: worn inserts are changed without complex adjustments, restoring cutting performance rapidly. Built for compatibility with ISCAR-manufactured inserts, the unit supports common tooling standards, simplifying inventory and reducing the need for bespoke tooling solutions. For robust, repeatable corner turning choose the Teknik Cutting Tools Angle Turning Head T446TM—contact Metav Werkzeuge in Emmerich for tailored application advice and parts supply via info@metav-werkzeuge.com or +49 2822 7131930. Technical data Article number: T446TM Name: Eckmesserkopf / Angle turning head Manufacturer: Teknik Makina Core specifications Shank diameter: 27 mm Weight: 1.238 kg Diameter: 80 mm Overall length: 52 mm Cutting angle: 90° Cutting edges: 6 Fastening screw: M5x12 Features / Compatibility Compatible inserts: ANKX 0706 Indexable Inserts Suitable for inserts by: ISCAR Torx key size: T20 SKU: T446TM Files: 62de7ef5a9cff922f4703d5a, 62de7e6e0aced56449540ea5 FAQ Which indexable inserts fit this toolhead? The head is specified for ANKX 0706 indexable inserts; the Angle Turning Head T446TM accepts these standard inserts for shoulder and profile turning. What torque or driver is required for insert clamping? Insert clamping uses a M5x12 Torx screw; a T20 Torx key is required to secure and remove the fastening screw on the T446TM. Which manufacturers’ inserts are compatible? The toolhead is compatible with inserts from ISCAR and other suppliers offering ANKX 0706-format indexable inserts; the Angle Turning Head T446TM follows that common insert interface. What machines is the head suited to? With a 27 mm shank interface and compact 52 mm length, the head is suited to conventional turrets and compact turrets on medium-duty CNC lathes and turning centres; its mass and diameter support stable cutting. How many cutting edges are available before replacement? The design provides for six cutting edges, enabling multiple indexings per insert and extended service intervals for the Angle Turning Head T446TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of the robust combination of replaceable CCMT 0602 inserts, a compact 80 mm diameter and a 27 mm shank for stable mounting — designed to cut set-up time and tooling costs while keeping productivity high. Order the cutter directly via Metav Werkzeuge or ask our consultants for application advice. Indexable Disc Cutter DF152TM by Teknik Makina — 80 mm, CCMT 0602 compatible The Indexable Disc Cutter DF152TM is an indexable disc cutter engineered for efficient slotting and shoulder milling tasks in CNC machining, using CCMT 0602 inserts for economical component production 80 mm diameter for stable slotting 10 mm cutting height for deep cuts Compatible with CCMT 0602 indexable inserts 27 mm shank diameter for secure mounting Boost throughput with indexable inserts and a compact design The replaceable CCMT 0602 inserts provide the main economic benefit: rapid index changes instead of full-tool replacement, which reduces downtime and tooling expenditure. The disc's 80 mm diameter and 10 mm cutting height allow reliable engagement for typical slotting and shoulder operations, while the relatively light overall mass keeps spindle load moderate. This combination supports higher feed rates and continuous production cycles without frequent interruptions, making the tool suitable for batch machining and repetitive operations where tool-change efficiency matters. Quick and secure set-up for dependable machining A 27 mm shank diameter ensures a rigid connection to tool holders, improving stability during cuts. The cutter is secured with M2.5x7 Torx screws (Torx key T08), enabling fast and repeatable insert clamping with standard workshop tools. The construction balances accessibility and rigidity, so flange runout is reduced and insert life is extended. The compact tool weight of 0.289 kg simplifies handling and storage while still delivering the clamping forces needed for consistent cutting performance. Practical use cases and machining advantages Designed primarily for slotting and face-turning-style operations on standard machining centres, the indexable design allows controlled material removal without custom regrinding. With an axial engagement of 16 mm and the specified insert form, the cutter supports efficient chip formation and predictable tool wear, which eases planning of reconditioning intervals and inventory of spare inserts. Process planners benefit from the straightforward geometry and widely available CCMT inserts, which simplify procurement and reduce lead times. Contact Metav Werkzeuge for tailored machining advice and secure supply from Emmerich — call +49 2822 7131930 or e‑mail info@metav-werkzeuge.com to discuss the DF152TM and compatible tooling solutions Technical data Article number: DF152TM Manufacturer: Teknik Makina Core specifications Diameter: 80 mm Cutting height: 10 mm Axial engagement: 16 mm Shank diameter: 27 mm Weight: 0.289 kg Design features Compatible with CCMT 0602 inserts Torx screw M2.5x7 Torx key T08 Indexable disc cutter design FAQ What inserts are compatible with this cutter? The cutter accepts CCMT 0602 indexable inserts; the DF152TM is designed for straightforward insert replacement to keep downtime minimal. What is the maximum cutting height of the tool? The tool provides a 10 mm cutting height, enabling robust slotting and shoulder cuts in typical CNC operations. Which shank diameter is required for mounting? A 27 mm shank diameter is specified for secure mounting of the DF152TM in standard tool holders. Which screw and key are needed to secure the inserts? Insert clamping is achieved with M2.5x7 Torx screws and a T08 Torx key for reliable and repeatable fixing. For which machining tasks is this cutter best suited? The tool is best suited to slotting and shoulder milling where indexable inserts and quick changeover support efficient batch production using the DF152TM Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust indexable inserts, proven mounting security and reduced downtime for continuous production performance; order the disc cutter directly via Metav Werkzeuge or ask Metav consultants for application support. Disc cutter DF150TM — indexable disc cutter, Ø 80 mm, CCMT 0602 compatible (Teknik Makina) The Disc cutter DF150TM is an indexable milling tool designed for medium-to-heavy duty slotting and peripheral milling with CCMT 0602 inserts, suited to workshop and industrial toolrooms Indexable disc cutter Ø 80 mm Compatible with CCMT 0602 inserts 10 cutting edges for efficient material removal 27 mm arbor bore, secure M2.5x7 Torx fixing Increase material removal while maintaining component quality The DF150TM delivers consistent cutting performance thanks to its Ø 80 mm diameter and 10 cutting edges, which together allow higher material removal rates with stable chip formation. The cutter’s 16 mm axial depth capability gives a practical balance between productivity and machine load; in practice this means fewer passes to achieve the required section, shortening cycle times and improving throughput. The combination of several indexed edges and a compact tool body helps maintain a uniform surface finish across repeats while keeping vibration to a minimum. Secure mounting and rapid serviceability for reduced downtime A reliable interface is essential in production. The tool’s 27 mm arbor bore ensures accurate seat on a matching arbor and contributes to concentric running. Inserts are retained with Torx M2.5x7 screws, tightened with a T08 key, enabling quick and repeatable insert changes and a secure clamping force. The specified 8 mm cutting height improves rigidity at the cutting zone, reducing tendency to chatter and lowering risk of premature insert wear. These features combine to simplify maintenance routines and shorten stoppage times during routine servicing. Indexable inserts: predictable costs and simple logistics Using standard CCMT 0602 indexable inserts allows cost-effective running: each insert provides multiple renewal faces, so toolholders remain in service longer and stocking requirements are minimised. Indexable systems separate cutting edge wear from the cutter body, which lowers consumable spend and simplifies logistics for procurement. For operations less familiar with insert systems: indexable inserts are small, replaceable carbide pieces that are clamped into the cutter head; when an edge wears, the insert is indexed or replaced without the need to change the complete cutter body. A trusted supply chain and practical support from Metav Sourcing through Metav Werkzeuge brings the advantage of a centralised precision supply and experienced application advice. Metav’s European distribution hub functions as a quality filter for workshop tools, backed by decades of experience and a broad stock range. For procurement managers and workshop supervisors this means reliable availability, straightforward ordering and the reassurance of tested product performance in everyday production environments. For tailored application advice or to place an order for the Teknik Makina DF150TM indexable disc cutter via Metav Werkzeuge, please contact Metav’s technical sales team by e‑mail or phone for precise integration guidance and delivery options. Technical data Article number: DF150TM Manufacturer: Teknik Makina Product name: Disc cutter DF150TM Data Diameter: 80 mm Cutting edges: 10 Axial depth (ap): 16 mm Cutting height: 8 mm Arbor bore: 27 mm Insert type: CCMT 0602 Fixing screw: M2.5x7 (Torx) Torx key: T08 Weight: 0.236 kg SKU: DF150TM eClass: 21180704 ETIM: EC011860 Special features Indexable insert system Rapid insert replacement Secure Torx clamping Balanced geometry for reduced vibration Suitable for workshop and industrial milling FAQ Which inserts fit this cutter? The cutter accepts CCMT 0602 indexable inserts; the DF150TM is designed around this insert format for stable cutting and simple replacement. What arbor diameter is required for mounting? Mounting requires a 27 mm arbor bore; the 27 mm arbor bore provides a concentric fit for precise running. How many cutting edges are available per tool? The tool has 10 cutting edges on the cutter body, enabling effective material removal and extended on‑tool life. What is the recommended axial depth for cutting? The specified axial depth for the tool is 16 mm, offering a compromise between removal rate and machine load for many shop applications. Which fixing hardware is supplied or required? Inserts are fastened with M2.5x7 Torx screws and the key size for servicing is T08 as noted for the DF150TM. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of a robust 80 mm cutting diameter, six cutting edges and a secure 27 mm arbor results in efficient material removal and stable tool life; order the cutter directly via Metav Werkzeuge or consult our experts for application advice. Round insert face mill T274TM — 80 mm diameter, 6 cutting edges (for RDMT 1604 indexable inserts) by Teknik Makina The Round insert face mill T274TM is a compact milling head for general-purpose and production milling where RDMT 1604 indexable inserts are used, delivering stable engagement and straightforward indexable-insert changes 80 mm cutting diameter for broad engagement Six cutting edges for continuous chip load distribution Compatible with RDMT 1604 indexable inserts 27 mm arbor for secure clamping and repeatability High productivity through geometry and edge count The milling head combines an 80 mm diameter with six cutting edges to increase cutting continuity and reduce the load per tooth. This geometry enables higher feed per rev while maintaining surface quality, so production cycles run more predictably. The distributed cutting action lowers vibration and contributes to longer insert life, which reduces tool change frequency and supports steady throughput on the shop floor. Secure clamping and standardised maintenance features The tool body is engineered for repeatable seating and easy maintenance: a 27 mm arbor provides stable mounting, while the locking arrangement uses a M4x10 locking screw and a M4.5x11 Torx screw for insert retention. A Torx key T20 and the U-plate reference BSP010 simplify replacement and indexing of inserts. These details mean less downtime for service and consistent cutting geometry after each insert change. Compact design for handling and process stability With an overall length of 50 mm and a weight of about 0.89 kg, the cutter balances rigidity and manoeuvrability. The relatively short overhang reduces bending moments and improves chatter resistance, which is beneficial in both small jobbing machines and larger CNC centres. The compact form factor also eases tool storage and handling during routine maintenance. Versatility in common milling workflows Designed for use with RDMT 1604 indexable inserts, the tool suits a variety of face milling and light profiling operations where indexed inserts are preferred. The combination of standard fasteners and a common insert format ensures spare parts and replacements are readily available, supporting uninterrupted production and a straightforward spare-parts strategy. Contact Metav Werkzeuge for tailored application advice or to secure supply of the Teknik Cutting Tools round insert face mill T274TM from our Emmerich distribution centre — call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data SKU: T274TM Manufacturer: Teknik Makina Product name: Round insert face mill T274TM Facts Diameter: 80 mm Cutting edges: 6 Shank / arbor diameter: 27 mm Overall length: 50 mm Weight: 0.89 kg Special features For RDMT 1604 indexable inserts Locking screw: M4x10 Torx screw: M4.5x11 Torx key size: T20 U-plate: BSP010 FAQ What insert type does this cutter use? The cutter is designed for RDMT 1604 indexable inserts, which allow quick indexing and predictable cutting geometry. How is the cutter clamped to the spindle? Clamping is provided via a 27 mm arbor diameter for secure mounting and repeatable positioning. Which screws and tools are required for insert changes? Insert retention uses a M4x10 locking screw and a M4.5x11 Torx screw; a T20 Torx key is specified for maintenance. Is the tool suitable for high-volume production? Yes; the combination of multiple cutting edges and a stable arbor connection supports continuous production with reduced insert wear. What are the dimensional limits to consider when fitting the cutter? Key dimensions are 80 mm cutting diameter, 50 mm overall length and 27 mm arbor — verify these against the machine’s tool holder clearances. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

The combination of an 80 mm diameter, six cutting edges and integrated internal coolant delivers reliable material removal and extended insert life; choose this compact, secure system for stable face milling operations. Order the round insert milling cutter directly via Metav Werkzeuge or consult the specialists for integration advice. Round Insert Milling Cutter for RPMT 1606 Indexable Inserts — 80 mm, internal coolant (Teknik Makina) The Round Insert Milling Cutter is a compact face milling head designed for stable, high-feed operations using RPMT 1606 indexable inserts and offering coolant through the body for controlled heat management. 80 mm diameter for stable material removal Six cutting edges for high productivity Internal coolant for improved chip evacuation Compatible with RPMT 1606 inserts (Korloy) Faster material removal with stable cutting geometry The 80 mm diameter head and the arrangement of the six cutting edges create a robust cutting geometry that reduces vibration and increases metal removal rates. In practical terms, this means shorter cycle times and more consistent surface finishes when machining castings or steel components. The design supports predictable tool behaviour at moderate to high feeds, translating the cutter’s specifications into measurable productivity gains on batch and single-part production alike. Coolant-through design protects inserts and reduces downtime The internal coolant channel supplies cutting fluid directly to the cutting zone to support chip evacuation and control heat generation. Direct coolant reduces thermal loads on the cutting edges and lowers the risk of built-up edge, which in turn improves tool life and stabilises part tolerances. For workshops where changeover and tool cost are critical, this feature helps reduce unplanned insert replacement and keeps machines running to schedule. Secure clamping and simple serviceability for workshop efficiency Fast, repeatable fastening is provided via M5x12 Torx screws and a T20 key, ensuring secure clamping of the indexable inserts and straightforward maintenance procedures. The cutter accepts RPMT 1606 inserts and is compatible with inserts from Korloy, enabling flexible inventory management. The compact overall length and modest mass make handling and tool changes easier for operators, while the clearly defined screw and key types simplify spare part stocking and service routines. Practical applications and integration into production Designed as a face milling head for a variety of workpieces, the tool is well suited to light to medium-duty roughing and finishing tasks on steel, cast iron and alloy components where RPMT 1606 grades perform best. The compact form factor and coolant feed make it a practical choice for machining centres with limited tool clearance. For procurement and supply reliability, Metav’s European distribution offers a dependable channel for fast replenishment and expert advice from a partner experienced in precision tooling. Contact Metav Werkzeuge today to secure availability of this Teknik Cutting Tools face milling solution and to discuss the best RPMT 1606 insert grades for the intended application Technical Data SKU: T718-1TM Diameter: 80 mm Overall length: 50 mm Number of cutting edges: 6 Weight: 1.048 kg Facts Insert type: RPMT 1606 Insert manufacturer compatibility: Korloy Torx screw: M5x12 Torx key: T20 Coolant through body: Yes Special features Face milling head design Compact overall length Secure Torx clamping Suitable for workshop and industrial machining FAQ What insert type does this cutter accept? The cutter accepts RPMT 1606 indexable inserts; it is supplied to work with Korloy grades and similar geometries suitable for face milling. Is the cutter coolant-fed and how does that help? Yes — the tool features internal coolant, which directs fluid to the cutting zone for improved chip evacuation and longer tool life. Which fastening hardware is required for insert replacement? Insert retention uses M5x12 Torx screws tightened with a T20 key for secure and repeatable clamping. What applications suit this face milling head? The design is ideal for face milling tasks on steel and cast iron components where a compact, coolant-fed head and six cutting edges deliver stable material removal. What is the product SKU for reorder or spare part queries? The SKU for this face milling cutter is T718-1TM, which should be referenced for ordering or spare hardware. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact tool head that combines secure clamping, precise 90° geometry and wide compatibility with LNGU 15T6 indexable inserts for steady, repeatable turning performance — order via Metav Werkzeuge or consult our specialists for application advice. T960TM right-angle turning head – 90° cutting geometry, for LNGU 15T6 indexable inserts (Teknik Makina) T960TM right-angle turning head for turning and shoulder operations with LNGU 15T6 indexable inserts, designed for stable mounting in standard 27 mm toolholders 90° cutting angle for perpendicular turning Compatible with LNGU 15T6 indexable inserts 27 mm shank diameter for sturdy mounting Torx M4x11 clamping screw, T15 key 80 mm head diameter, 7 cutting edges Precision and rigidity for consistent component quality The T960TM is engineered to provide a 90° cutting angle that simplifies shoulder and face turning while preserving dimensional accuracy. A 27 mm shank delivers increased stiffness at the toolholder interface, which reduces vibration and secures a more consistent surface finish and tighter tolerances in serial production. The compact 80 mm head diameter and an overall length of 50 mm make the unit well suited to confined setups where rigidity and accessibility are equally important. These design choices translate into fewer reworks and higher first-pass yield for repetitive machining tasks. Fast insert changes and secure clamping to keep production moving The tool head accepts LNGU 15T6 indexable inserts and is specified as compatible with Kennametal insert geometries, enabling rapid plate changes and straightforward inventory management. Insert retention is provided by a Torx M4x11 clamping screw driven with a T15 key, offering a reliable clamp force with minimal setup time. Quick, repeatable insert changes reduce machine downtime and support lean workflows on the shop floor, allowing operators to maintain cycle times without compromising safety or clamping integrity. Robust geometry and simple integration for versatile turning tasks With seven defined cutting facets and a balanced mass of 1.133 kg, this right‑angle tool head is dimensioned for stability during interrupted cuts and heavier engagement. The short 50 mm overall length helps to limit overhang and maintain cutting stability even in heavier machining conditions. Compatibility with standard 27 mm toolholders ensures easy integration into existing turret and toolpost arrangements, so the head can be deployed across multiple lathes without extensive fixturing changes. The result is a practical, durable solution that supports predictable throughput and long service intervals. Contact Metav Werkzeuge today to discuss the T960TM right‑angle turning head from Teknik Makina, request technical matching for specific insert grades or arrange specialist advice via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: T960TM Manufacturer: Teknik Makina Facts Shank diameter: 27 mm Head diameter: 80 mm Overall length: 50 mm Weight: 1.133 kg Cutting angle: 90° Number of cutting facets: 7 Special features Compatible insert type: LNGU 15T6 Compatible insert manufacturer: Kennametal Clamping screw: Torx M4x11 Torx key size: T15 FAQ What inserts fit this turning head? The T960TM is specified for LNGU 15T6 indexable inserts and is compatible with Kennametal insert types of the same designation. Which shank diameter is required for mounting? This right‑angle turning head requires a 27 mm toolholder bore for correct and secure mounting. How is the insert secured in the head? Inserts are retained with a Torx M4x11 clamping screw that is tightened with a T15 key to ensure consistent clamping force. Is the tool head suitable for shoulder and facing operations? Yes; the 90° cutting angle and compact geometry make the head well suited to perpendicular turning, face cutting and shoulder work where rigidity is essential. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Benefit from a compact, indexable design that combines an 80 mm diameter, compatibility with SCMT 09T3 inserts and a 27 mm shank for stable machining; this reduces downtime and keeps set-up straightforward. Order the disc cutter directly via Metav Werkzeuge or ask our consultants if needed. Indexable Face Mill DF086TM – 80 mm diameter, for SCMT 09T3 inserts by Teknik Makina The Indexable Face Mill DF086TM is a compact disc cutter optimised for face and light slot milling where quick insert changes and predictable performance are required Indexable design for SCMT 09T3 inserts 80 mm diameter for medium face milling 8 cutting edges for efficient material removal 27 mm shank, 10 mm cutting height Faster machining through indexable-insert efficiency The indexable insert concept reduces unproductive time: with compatibility for SCMT 09T3 inserts and 8 cutting edges, re-indexing is minimised and insert changes are fast. The combination of an 80 mm diameter and a recommended axial engagement of 17 mm allows stable chip formation for many standard face-milling tasks, while the 10 mm cutting height gives scope for deeper passes within the cutter’s compact envelope. These technical attributes translate directly into improved throughput and shorter cycle times on batch runs. Reduced tooling complexity and secure clamping A 27 mm shank offers robust mounting in common toolholders and supports accurate centring during operation. The cutter uses M4x11 Torx clamping screws with a T15 key interface for reliable insert retention and repeatable tightening torque — a setup that reduces the risk of loose clamps and scrap parts. At only 0.229 kg, the tool is easy to handle during changeover while remaining rigid enough for stable cutting. The result is simplified tool management and fewer set-up interruptions in a busy workshop. Dependable design that supports production continuity Replaceable inserts mean predictable maintenance intervals and lower long-term tooling costs compared with solid tools. The disc cutter’s modular approach supports fast replacement routines and consistent cutting geometry over time, which is beneficial for repeat production. Paired with Metav Werkzeuge’s distribution and technical support, the tool integrates into a supply chain designed for reliable availability and practical advice, helping maintain steady output without unnecessary downtime. For procurement advice and technical clarification on the DF086TM indexable face mill, contact Metav Werkzeuge for personalised support and delivery options at info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: DF086TM Manufacturer: Teknik Makina eClass: 21180704 ETIM: EC011860 Data Diameter: 80 mm Cutting edges: 8 ap (axial depth): 17 mm Cutting height: 10 mm Shank diameter (aufnahme): 27 mm Weight: 0.229 kg Special features Compatible inserts: SCMT 09T3 Torx screw: M4x11 Torx key size: T15 Indexable, replaceable inserts Compact disc cutter design FAQ What inserts fit this face mill? The Indexable Face Mill DF086TM accepts SCMT 09T3 inserts; this compatibility simplifies parts provisioning and ensures secure seating for each cutting edge. What is the maximum axial engagement recommended? The cutter is specified with an axial engagement of 17 mm, which balances material removal with stable engagement for routine face-milling operations. Which shank size is required for mounting? A 27 mm shank diameter is required for mounting the DF086TM in a compatible toolholder to ensure stable clamping and concentricity. How does the clamping system work? Clamping is achieved with M4x11 Torx screws tightened using a T15 key, providing repeatable and secure insert retention for consistent cutting performance. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; info@metav-werkzeuge.com

Take advantage of a compact, production-ready turning solution that combines machining stability and straightforward setup for fast insert changes; the combination of Ø80 mm head diameter and a 90° cutting angle delivers consistent corner turning performance — order via Metav Werkzeuge or consult our specialists for application advice. Corner tool head T128TM — 90° corner turning head, Ø80 mm, for indexable inserts The Corner tool head T128TM is a robust clamping head for turning operations, engineered to accept TPKN 1603–2204 indexable inserts for precision corner cutting on lathes and CNC turning centres. 90° cutting angle for corner turning Designed for TPKN 2204 indexable inserts Ø80 mm head diameter for rigidity 32 mm shank, M8x24 fixing screw Stable machining and consistent corner results The compact head geometry with a 90° cutting angle and Ø80 mm diameter increases stiffness at the cutting zone, which results in improved process stability and reduced chatter during corner turning. The tool head has four cutting edges configured to support repeatable engagement and even wear distribution; such mechanical balance helps to maintain part quality across serial production runs. This design supports efficient material removal where right‑angled cuts or shoulder finishes are required, while the mass of 0.795 kg contributes to vibration damping without compromising toolholder compatibility. Quick clamping and straightforward insert changes Setup and maintenance are kept simple by the exposed fixing arrangement: the head is secured with an M8x24 hex screw and requires a 5 mm Allen key for tightening. The 32 mm shank diameter facilitates secure seating in standard toolholders and reduces changeover time on the shop floor. The overall length of 52 mm allows a compact footprint in tight turret stations; as a result, changeover and re‑indexing procedures are faster, contributing to shorter downtimes and more predictable cycle times during shift work. Built for workshop durability and universal compatibility Designed specifically for TPKN 2204 inserts and listed as compatible with TPKN 1603–2204 insert types, the head fits common insert families used in general turning and finishing tasks. The combination of a substantial head diameter and multiple cutting edges promotes longer service intervals by distributing cutting forces more evenly across the insert seat. The compact form factor makes the component suitable for both conventional lathes and modern CNC turning centres that demand reliable, repeatable tool performance in corner and face turning operations. For application advice or to confirm fitment of Teknik Makina’s corner tool head T128TM with existing tool posts, contact Metav Werkzeuge for tailored support at info@metav-werkzeuge.com or by phone on +49 2822 7131930 Technical Data SKU: T128TM Manufacturer: Teknik Makina Description: for TPKN 1603-2204 indexable inserts Facts Shank diameter: 32 mm Head diameter: 80 mm Cutting angle: 90° Number of cutting edges: 4 Overall length: 52 mm Weight: 0.795 kg Fixing screw: M8x24 Required Allen key: 5 mm Special features Suitable for TPKN 2204 indexable inserts Compatible with TPKN 1603–2204 insert family Four cutting edges for even wear Compact 52 mm overall length Designed for use in lathes and CNC turning centres FAQ How does the head secure the insert and which screw is required? The Corner tool head T128TM secures the insert with an M8x24 fixing screw; tightening is performed with a 5 mm Allen key. Which insert types are compatible with this turning head? This clamping solution is compatible with the TPKN 2204 insert family and supports the TPKN 1603–2204 indexable inserts for right‑angle corner turning. Will the T128TM fit standard toolholders? The T128TM has a 32 mm shank diameter and a 52 mm overall length, designed to fit common toolholders used on lathes and CNC turning centres. How many cutting edges does the head provide and what is the benefit? The head features four cutting edges, which promote even wear distribution and more consistent machining results across serial batches. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, robust turning solution with a 90° cutting angle, compatibility with APKT 1003 indexable inserts and a sturdy 27 mm shank for stable toolholding; order or discuss tooling requirements directly via Metav Werkzeuge for reliable supply and expert advice. Eckmesserkopf T179TM — 90° corner turning head for APKT 1003 inserts by Teknik Makina The Eckmesserkopf T179TM is a compact corner turning head designed for precision external turning and profiling using APKT 1003 indexable inserts, suitable for workshop and production environments 90° cutting angle for precise profiling Compatible with APKT 1003 indexable inserts Fits Korloy APKT 1003 insert geometry 27 mm shank with 80 mm head diameter Engineered rigidity for consistent turning results Built with a focus on stability, the head’s Ø 80 mm diameter and 27 mm shank deliver a rigid connection to the toolpost, reducing vibration and supporting repeatable part geometry. The 90° cutting angle provides predictable engagement for external profiling and square shoulder operations, enabling consistent surface finish and dimensional control. The stated weight of 1.205 kg contributes to mass damping without excessive tool overhang, which helps maintain concentricity and prolong insert life. Fast, secure insert changes minimise downtime Maintenance and index changes are simplified thanks to compatibility with APKT 1003 indexable inserts and a straightforward fastening system. The insert is secured with an M2.5x5.5 Torx screw operated by a T8 key, which allows quick tightening and reliable clamping force for repeatable seating. The Eckmesserkopf T179TM from Teknik Makina supports efficient shopfloor routines: reduced set‑up time and fast insert exchange mean less idle machine time and higher productivity per shift. Practical dimensions and simplified inventory management The head’s 50 mm overall length and compact profile make it suitable for confined setups and multi‑operation fixtures, while the availability for Korloy APKT 1003 inserts reduces the need for specialised spare stocks. With eight cutting edges the configuration supports indexed tool life extension when combined with multi‑edge inserts, and the standardised interface facilitates integration into existing toolholder systems. Clear, measurable data such as shank diameter and head Ø simplify purchasing decisions and ensure interchangeability across compatible toolholders. Contact Metav Werkzeuge for tailored application advice and delivery options for Teknik Makina tooling: info@metav-werkzeuge.com | +49 2822 7131930 Technical data Article number: T179TM Manufacturer: Teknik Makina Designation: Eckmesserkopf for APXT 1003 Indexable Inserts Facts Weight: 1.205 kg Head diameter: 80 mm Shank diameter: 27 mm Overall length: 50 mm Cutting angle: 90° Number of cutting edges: 8 Special features Compatible inserts: APKT 1003 Compatible insert brand: Korloy Torx screw: M2.5x5.5 Torx key size: T8 FAQ Which insert type fits this turning head? The Eckmesserkopf T179TM is designed for APKT 1003 indexable inserts; Korloy APKT 1003 geometry is explicitly compatible. How is the insert fastened to the head? Insertion is secured with an M2.5x5.5 Torx screw, tightened using a T8 Torx key for consistent clamping. What are the key dimensions to check for mounting? Relevant dimensions are head Ø 80 mm, shank 27 mm and overall length 50 mm; weight is 1.205 kg. Is the head suitable for 90° profiling and shoulder turning? Yes, the integrated 90° cutting angle is configured for precise profiling and square shoulder operations. Can other insert brands be used with the same geometry? The head accepts inserts matching the APKT 1003 geometry; brands that adhere to that ISO form, such as Korloy, will be compatible. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 90° cutting geometry and the stable 27 mm shank for reliable corner turning; order the corner turning head directly via Metav Werkzeuge or consult the technical advisers for application-specific guidance. Corner Turning Head T230TM — indexable insert holder for LNMT 1306, 90° cutting angle (Teknik Makina) The Corner Turning Head T230TM is a compact tool head engineered for turning operations with LNMT 1306 indexable inserts, offering a combination of accurate corner geometry and robust clamping for workshop environments Compatible with LNMT 1306 inserts (ISCAR) 90° cutting angle for predictable corner geometry 27 mm shank for secure machine mounting 80 mm diameter and 50 mm overall length Predictable cornering for consistent part geometry The 90° cutting geometry delivers a defined cutting direction that reduces the need for secondary finishing and simplifies process planning. By pairing the body with LNMT 1306 indexable inserts, the holder ensures repeatable engagement at the corner, which translates to precision in profile and form tolerances. The design supports consistent chip flow and surface quality, enabling machines to run predictable cycles with fewer interventions. Secure clamping and fast insert handling to improve throughput A robust clamping concept combined with the 27 mm shank improves tool stability and vibration damping during interrupted cuts. Fixing is achieved with an M4x10 Torx screw, tightened using a T15 key, allowing quick and secure insert changes while keeping set-up time to a minimum. The unit’s modest 50 mm length and 80 mm diameter balance accessibility in tight assemblies with sufficient mass for stable operation; the assembly weight of 1.227 kg contributes to reduced chatter and enhanced surface finish. Workshop compatibility and streamlined logistics Compatibility with standard insert contours from established manufacturers ensures broad applicability across turning applications and makes stocking simple. The tool head accepts inserts produced to the LNMT 1306 specification and is listed as ISCAR compatibility, so existing insert inventories can be used without modification. The result is lower tooling complexity on the shop floor and easier procurement planning when replacing or expanding tool sets. Contact Metav Werkzeuge to confirm fitment for specific machines, check stock availability in Emmerich, or request application advice for the Teknik Makina T230TM corner turning head — eMail: info@metav-werkzeuge.com • Tel: +49 2822 7131930 Technical data Article number: T230TM Manufacturer: Teknik Makina Facts Diameter: 80 mm Shank diameter (d): 27 mm Total length: 50 mm Weight: 1.227 kg Cutting angle: 90° Special features Compatible with LNMT 1306 indexable inserts ISCAR compatibility Torx screw M4x10 Torx key size T15 Number of cutting edges: 9 FAQ Which inserts fit the tool head? The T230TM accepts LNMT 1306 indexable inserts and is compatible with ISCAR-manufactured inserts to that specification. What is the nominal cutting angle? The holder is configured with a 90° cutting angle, ensuring well-defined corner geometry for predictable machining. How is the insert secured? Insert retention uses an M4x10 Torx screw, tightened with a T15 key for secure clamping and straightforward replacement. Is the tool head suitable for tight installations? Yes — the compact overall length of 50 mm and 80 mm diameter make the holder suitable for constrained setups while maintaining rigidity. Which shank diameter is required for mounting? The holder requires a 27 mm shank for proper machine mounting and secure clamping. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, purpose-built 90° turning head that combines precise corner machining with secure clamping and straightforward serviceability; the robust design and compatibility with Sandvik R390-1704 indexable inserts support consistent production results. Order the Teknik Makina tool directly via Metav Werkzeuge or consult the Metav team for application advice. Eckmesserkopf T411TM — 90° turning head for R390-1704 indexable inserts (Teknik Makina) The Eckmesserkopf is a compact 90° turning head for R390-1704 indexable inserts, engineered for accurate corner machining and reliable mounting in demanding turning operations. 90° cutting angle for accurate corner machining Compatible with Sandvik R390-1704 inserts 27 mm shank for secure toolholder mounting Torx M3.5×8.5 screw, T15 key fastening Accurate corner machining with 90° geometry The 90° geometry delivers a predictable tool path for corner and shoulder turning, reducing the need for secondary finishing. The combination of a defined 90° cutting angle and compatibility with R390-1704 indexable inserts ensures consistent contact conditions at the cutting edge, which contributes to repeatable surface quality. For operators unfamiliar with insert design, indexable inserts are replaceable cutting tips that allow fast renewal of cutting edges without regrinding, lowering total tool life costs while maintaining process stability. Stable clamping and straightforward fastening for repeatable results A 27 mm shank provides a rigid connection to the turret or holder, helping to minimise vibration and runout during heavy cuts. The insert is secured with a Torx M3.5×8.5 screw and released with a T15 key, a common fastening standard that simplifies maintenance and tool change procedures in the workshop. The secure clamping arrangement reduces the risk of insert movement under load, improving dimensional accuracy and prolonging insert life. Compact form that supports productivity in tight setups With a head diameter of 80 mm and an overall length of 52 mm, the toolhead is designed for access into constrained bores and close-quartered turned features. The relatively compact profile, combined with a weight of 1.168 kg, balances rigidity with manoeuvrability on the turret. The specification of 7 cutting edges indicates the number of usable cutting positions inherent to the compatible insert family, enabling multiple indexed positions before replacement and supporting continuous production runs. Compatibility, handling and workshop integration The toolhead is specified for use with Sandvik R390-1704 inserts, making it straightforward to source replacements from common industrial suppliers. Mounting requires only a T15 Torx key to remove or clamp the M3.5×8.5 screw, simplifying routine insert changes and minimising downtime. The robust mechanical features mean that the corner turning head integrates readily into established turning processes, offering predictable performance without additional special tool interfaces. Contact Metav Werkzeuge for tailored application guidance on the Teknik Makina T411TM Eckmesserkopf and to confirm compatibility with specific machine turrets — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for prompt assistance Technical data Article number: T411TM Brand: Teknik Makina Product: Eckmesserkopf For: for R390-1704 Indexable Inserts Torque screw: M3.5×8.5 Torx key: T15 Compatible insert maker: Sandvik Facts Shank diameter: 27 mm Overall length: 52 mm Diameter: 80 mm Weight: 1.168 kg Cutting angle: 90° Cutting edges: 7 Special features Suitable for R390-1704 indexable inserts Torx fastened insert clamping Compact head for tight machining zones SKU: T411TM Brand: Teknik Makina FAQ Which inserts fit this turning head? The turning head accepts R390-1704 indexable inserts; the design is matched to the insert geometry specified for that family. What is the shank diameter for mounting? The shank diameter is 27 mm, providing a rigid fit for standard turret toolholders. How is the insert secured and which key is required? The insert is secured with an M3.5×8.5 Torx screw, removable and tightened using a T15 key for straightforward servicing. What cutting angle does the toolhead provide? The toolhead features a 90° cutting angle, optimised for accurate corner and shoulder turning operations. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the compatibility with SPMG 0904 indexable inserts and a true 90° cutting angle for reliable corner operations; secure fastening via a M3.5x8.5 Torx screw and compact dimensions support quick changeovers. Order the corner tool head directly via Metav Werkzeuge or ask our consultants if needed. Corner tool head T342TM — for SPMG 0904 indexable inserts, 90° cutting angle (Teknik Makina) The Corner tool head is a compact turning head designed for use with SPMG 0904 indexable inserts, intended for precision cornering and face-turning tasks in small-batch and job-shop environments. For SPMG 0904 indexable inserts 90° cutting angle for accurate cornering Ø 80 mm head diameter 27 mm shank diameter Precision and compatibility for consistent turning results The T342TM corner tool head is designed around the widely used SPMG 0904 insert form to deliver repeatable edge engagement and controlled chip formation. The 90° cutting angle ensures that the cutting edge meets the workpiece at a defined geometry, which simplifies tool path planning and reduces the need for compensatory adjustments. This focus on fixed geometry supports efficiency on small-series parts where setup time has a direct impact on cost per piece. The compact tool design incorporates established insert standards, so familiar insert grades and coatings can be deployed without additional tooling investment. Robust mounting and service-friendly fastening A secure connection is provided by the 27 mm shank and a standard Torx clamping system, which is optimised for workshop turnaround. The 27 mm diameter shank gives a stable axial fit in compatible toolholders, while the clamping screw specification (M3.5x8.5) and the T15 driver allow fast replacement of inserts and straightforward maintenance. Because replacement is quick and repeatable, set-up times are reduced and tool downtime is minimised — a practical benefit for production shops where uptime drives throughput. Balanced dimensions for controlled chip removal and stability The tool head’s Ø 80 mm diameter and overall length of 52 mm create a compact centre of mass that improves rigidity during shoulder and face operations. The unit weight (1.088 kg) contributes to a well-damped assembly when installed in standard holders, helping to avoid chatter in many typical machining conditions. The design accommodates 7 cutting edges on the head assembly, which aids in distributing cutting forces and supports consistent surface finish over repeated cycles. These dimensional choices were made to favour steadiness over extreme outreach, making the head suitable where stability and predictable performance are priorities. Application scenarios and specification guidance This corner tool head is a practical choice for workshops and contract manufacturers working with square inserts from recognised brands such as Taegutec. The unit is supplied as a compact turning head that pairs with standard indexable inserts, so component programmers and tooling buyers can specify it by its SKU, T342TM, when planning inventories. For buyers seeking a reliable supply route and technical advice, Metav’s distribution offers a quality filter for the European market and can support selection of insert grades and coatings to match particular workpiece materials. For specification, availability and supply from Metav Werkzeuge in Emmerich, request a detailed parts and compatibility consultation referencing the T342TM corner tool head — eMail info@metav-werkzeuge.com or call +49 2822 7131930 to arrange prompt support and delivery. Technical data Article number: T342TM Name: Corner tool head Brand: Teknik Makina Compatible inserts: SPMG 0904 Compatible insert manufacturer: Taegutec Numbers / Core technical data Head diameter: 80 mm Shank diameter: 27 mm Overall length: 52 mm Weight: 1.088 kg Cutting angle: 90° Cutting edges: 7 Special features / Versions Torx screw: M3.5x8.5 Torx key size: T15 For SPMG 0904 indexable inserts Compact turning/cornering head design SKU: T342TM FAQ What insert size does this head accept? The head accepts SPMG 0904 indexable inserts, a square-format insert commonly used for cornering and face-turning operations. Which toolholder shank is required for mounting? A toolholder able to accept a 27 mm shank is required; the shank diameter is specified as 27 mm on the T342TM unit. How is the insert secured to the head? The insert is secured using a Torx clamping screw specified as M3.5x8.5; a T15 driver is recommended for tightening. Is the head compatible with Taegutec inserts? Yes, the T342TM is specified as compatible with inserts from Taegutec listed under SPMG 0904. What are the main dimensional constraints to check before ordering? Confirm the Ø 80 mm head diameter and overall length (52 mm) fit the intended clearance envelope and that the toolholder accepts a 27 mm shank. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a robust 90° indexable tool head combining a standard 27 mm shank with secure Torx clamping for stable corner turning and reduced setup times. Order directly via Metav Werkzeuge or consult our specialists for application advice and delivery from Emmerich. Eckmesserkopf — 90° indexable tool head for XNKT 0604 inserts by Teknik Cutting Tools The Eckmesserkopf is a 90° indexable tool head designed for precise corner turning and shoulder work with XNKT 0604 indexable inserts in general workshop and production turning operations 90° cutting angle for precise corner turning Compatible with XNKT 0604 indexable inserts 27 mm shank diameter for standard mounts Torx M3x7 clamp screw for secure fixing Precision corner turning with proven cutting geometry The 90° cutting geometry delivers a reliable solution for machining sharp shoulders and external corners, ensuring repeatable results on each workpiece. Built to accept XNKT 0604 indexable inserts, the head allows quick insert changes while preserving process stability. The design reduces the need for regrinding and complicated set-ups, enabling shorter cycle times and consistent profile accuracy across batches. For operations where tolerances matter, the combination of a defined cutting angle and indexable tooling supports predictable component quality. Secure mounting and mechanical stability that reduces vibration A 27 mm shank and an overall length of 50 mm create a compact, rigid connection to the holder, improving chatter resistance during turning. The head’s 80 mm diameter contributes to mass and damping, while the Torx clamping arrangement — M3x7 clamp screw with T8 interface — ensures a positive, repeatable fixation of the insert seat. At approximately 0.938 kg, the unit balances inertia and handling convenience, making it easier to position and tighten without compromising stability. These construction choices translate into improved surface finish and reduced scrap rates in production runs. Compatibility and operational efficiency for workshop use Designed for compatibility with Korloy-type inserts and specifically for the XNKT 0604 geometry, the tool head supports common insert inventories and simplifies procurement. The availability of multiple cutting edges (ten in the specified configuration) lowers the frequency of full-tool exchanges and helps sustain machining uptime. Intended for serial turning and finishing passes, the component integrates with existing indexable-insert workflows to deliver quick insert indexing, straightforward maintenance and lower overall tool management effort, making it suitable for both jobbing shops and in-house production departments. For a reliable 90° indexable tool head from Teknik Cutting Tools and support tailored to the application, contact Metav Werkzeuge for expert advice and supply from Emmerich. Technical Data SKU: T856TM Manufacturer: Teknik Makina Product: Eckmesserkopf — for XNKT 0604 indexable inserts Facts Shank diameter: 27 mm Weight: 0.938 kg Cutting angle: 90° Head diameter: 80 mm Overall length: 50 mm Number of cutting edges: 10 Clamp screw: M3x7 Torx key size: T8 Special features Compatible insert type: XNKT 0604 Compatible insert manufacturer: Korloy Application: corner turning, shoulder machining FAQ What insert type is required for this tool head? The Eckmesserkopf accepts XNKT 0604 indexable inserts; Korloy XNKT 0604 geometry is specified for correct fit and performance. Which shank size is used for mounting? Mounting is achieved with a 27 mm shank diameter, offering compatibility with standard tool holders designed for that dimension. How is the insert secured in the head? The insert is clamped using a Torx M3x7 clamp screw; the matching torx key size is T8 for tightening. Is the head suitable for heavy-duty turning operations? With a robust 80 mm head diameter and a mass of about 0.938 kg, the tool head provides good damping and stability for many turning tasks, especially shoulder and corner machining. How does the 90° geometry benefit production processes? The 90° cutting angle simplifies shoulder creation and profiling, improving repeatability and reducing set-up adjustments in serial production. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a rigid, industry-ready turning solution that pairs precision 90° geometry with direct compatibility for LOEX 1207 indexable inserts, enabling consistent shoulder finishes and reduced setup time; order via Metav Werkzeuge or consult our technical team for application support. Corner Tool Head T588TM — 90° turning head for LOEX 1207 indexable inserts by Teknik Makina The Corner Tool Head T588TM is a 90° turning head designed for LOEX 1207 indexable inserts, built for accurate external turning, facing and shoulder operations in general workshop and industrial turning applications 90° cutting angle for precise shoulder cuts Compatible with LOEX 1207 indexable inserts by SECO 27 mm tool holder shank diameter Torx fixing M4x10 with T15 drive Head Ø80 mm, overall height 50 mm, weight 1.03 kg Accurate shoulder machining with repeatable results This turning head features a 90° cutting geometry that delivers clear, square shoulders with minimal rework. By accepting LOEX 1207 indexable inserts, the head provides the advantage of fast insert replacement and consistent cutting edges without the need for regrinding; indexable inserts are replaceable carbide plates that rotate to fresh edges, which reduces downtime and keeps cycle times predictable. The head's geometry is especially beneficial where right-angled shoulders and stepped diameters are frequent, as a single set-up now produces repeatable results and reduces downstream finishing operations. Rigid mounting and straightforward serviceability Rely on a stable toolholder configuration: the head mounts on a 27 mm shank and uses a Torx M4x10 clamping screw with T15 drive for secure insert fixation and quick servicing. The combination of a 27 mm shank and a head mass of 1.03 kg increases stiffness at the cutting zone, reducing chatter and improving surface finish. Maintenance is simplified by the Torx connection, which allows controlled torque and fast, repeatable insert changes, so wear is managed without lengthy machine downtime. Compact design for effective integration and productivity With a head Ø80 mm and overall height of 50 mm, the holder balances compactness and rigidity to fit many toolposts while maintaining clearance for complex part geometries. The unit lists seven cutting edges, which supports extended tool life through indexed insert rotation and reduces the frequency of replacement—translating into measurable productivity gains on batch work. Compatibility with SECO-style inserts ensures easy sourcing from standard suppliers and smooth integration into existing tooling systems, enabling cost-efficient upgrades to turning capacity. For application recommendations or to place an order for the Teknik Makina Corner Tool Head T588TM, contact Metav Werkzeuge for tailored advice and supply via info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T588TM E-class: 21181015 Manufacturer: Teknik Makina Facts Shank diameter: 27 mm Head diameter: 80 mm Overall height: 50 mm Weight: 1.03 kg Cutting angle: 90° Cutting edges: 7 Special features Compatible inserts: LOEX 1207 (SECO) Torx screw: M4x10 Torx key size: T15 SKU: T588TM Files available: 66c4a4ca2a22f06ba2d88a20, 66c4a4caacd42255e1a26153 FAQ Is this head compatible with SECO LOEX 1207 inserts? Yes. The Corner Tool Head T588TM is designed for LOEX 1207 indexable inserts and is compatible with inserts supplied under the SECO system. What shank size is required for mounting? The turning head uses a 27 mm shank diameter; ensure the toolpost or holder accepts a 27 mm shank for secure mounting. Which screw and driver are required for insert clamping? Insert clamping is secured with a Torx M4x10 screw; a T15 Torx driver is specified for controlled tightening. What applications suit this turning head best? The head is optimised for external turning, facing and square shoulder machining where a 90° geometry improves repeatability and finish quality. How does the design affect vibration and finish? The combination of a 27 mm shank, Ø80 mm head and a mass of 1.03 kg increases rigidity at the cutting point, which helps to reduce vibration and improve surface finish. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of 80 mm diameter, internal coolant and a precise 90° cutting angle to improve process stability and reduce rework; order the corner tool head directly via Metav Werkzeuge or consult the technical team for application advice. Corner tool head for ADKT 10T3 indexable inserts — 80 mm, internal coolant (Teknik Makina) Corner tool head for shoulder and profiling operations, compatible with ADKT 10T3 indexable inserts and designed for robust machining in production environments Large 80 mm diameter for robust engagement Integrated internal coolant for improved chip control Compatible with ADKT 10T3 indexable inserts Secure Torx T8 fastening with M2,5x5,5 screws Precision and stability for reliable shoulder machining The combination of the 80 mm diameter and a compact 50 mm overall length produces a rigid tooling solution that reduces vibration during shoulder turning and facing operations. The 90° geometry delivers consistent square shoulders with minimal secondary machining, while the distribution of the eight cutting edges helps to spread cutting forces and extend the life of each indexable tip. By using an indexable system, maintenance becomes straightforward: worn tips are rotated or replaced without single-point regrinding, which shortens downtime and increases throughput. Coolant-through design that improves tool life and surface quality Built with internal coolant, the head directs coolant close to the cutting zone to aid chip evacuation and heat control. This targeted cooling reduces thermal load on the insert’s cutting edge, which can postpone edge chipping and crater wear and thus lengthen insert life. For customers unfamiliar with the term: internal coolant (coolant-through) means the coolant is channelled through the tooling body and delivered at the insert seat, enhancing lubrication and flushing chips away from the cutting zone for improved surface finish and process reliability. Fast, repeatable set-up and secure fastening Assembly and insert clamping are simplified by the Torx system: the head uses a T8 Torx key and M2,5x5,5 fastening screws for consistent torque and repeatable seating. Compatibility with Korloy ADKT 10T3 inserts ensures easy sourcing of tips and proven cutting grades for a wide range of steels. At 0.88 kg, the head balances mass for stability without excessive load on the toolholder; the compact design supports quick tool changes and predictable repeatability in series production. Where this head generates the most value on the shop floor This tooling head excels where square shoulders, tight tolerances and economic insert usage are required: small-batch production, toolroom rework, and medium-series turning. The ADKT 10T3 interface enables flexible grade selection for steel, alloy and general-purpose turning tasks, while internal coolant and robust fastening reduce unexpected stops. For procurement teams, the head offers a straightforward route to improved cutting consistency without complex adaptation of existing holders. For a direct technical match and to secure the Teknik Makina corner tool head with internal coolant, contact Metav Werkzeuge in Emmerich via info@metav-werkzeuge.com or call +49 2822 7131930 to discuss application specifics and delivery options. Technical data Article number: T700TM SKU: T700TM Product type: Corner tool head Brand: Teknik Makina Label: 80mm Eckmesserkopf ADKT 10T3 L50mm mit Innenkühlung Facts Diameter: 80 mm Overall length: 50 mm Weight: 0.88 kg Cutting angle: 90° Cutting edges: 8 Torx key: T8 Torx screw: M2,5x5,5 ECLASS: 21181015 Special features Internal coolant (coolant-through) For ADKT 10T3 indexable inserts Compatible insert manufacturer: Korloy Secure Torx fastening for repeatable assembly FAQ What insert type does this head accept? The head is designed for ADKT 10T3 indexable inserts and is specified for use with Korloy insert variants. Does the tooling head provide coolant-through capability? Yes, the corner tool head features internal coolant to improve chip evacuation and cooling at the cutting edge. Which fastening method is used for the inserts? Insertion is secured with a Torx system; the head requires a T8 key and uses M2,5x5,5 screws for repeatable clamping. Is this head suitable for producing square shoulders? The 90° cutting angle and robust 80 mm diameter make the head well suited to accurate shoulder and profile turning. Can the head be used with inserts from other manufacturers? The tooling head is specified for ADKT 10T3 inserts; compatibility with other brands depends on the exact insert geometry but Korloy ADKT 10T3 are confirmed. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine the adjustable 80–130 mm clamping range with proven compatibility for CCMT 09T3 inserts and secure Torx fastening to streamline internal turning operations; order the cartridge directly via Metav Werkzeuge or consult our advisers for application support. Cartridge 80-130mm for Boring Tool (THB09TM) — Teknik Makina, compatible with CCMT 09T3 The Cartridge 80-130mm for Boring Tool is a precision mounting component for internal boring and turning applications, engineered to deliver consistent seating and repeatable results in production and workshop environments Adjustable 80–130 mm diameter range Compatible with CCMT 09T3 inserts Torx T15 fastening, M3.5x8.5 screw Consistent internal machining through a wide adjustable range The mounting unit offers an adjustable 80–130 mm clamping range that removes the need for frequent holder swaps on varied bore diameters. This flexibility shortens set-up times and supports a steady production flow by allowing one holder to cover multiple shaft sizes. The design emphasises precision and repeatability: controlled clamping and accurate insert positioning reduce radial runout and the risk of rework. For workshops aiming to optimise throughput, the cartridge acts as a reliable element within a modular boring system. Secure fastening and simple serviceability for less downtime Fastening is achieved via a Torx T15 drive and a M3.5x8.5 screw, providing a robust fastening method that resists loosening under cutting loads. The clear screw specification ensures compatible spares and straightforward maintenance routines. The insert pocket accepts standard brazed and indexable tools, so insert changes are quick and toolholding integrity is maintained. Reduced maintenance complexity translates directly into lower process interruptions and predictable toollife management in everyday shop-floor use. Compatible insert system that simplifies tooling logistics Designed for use with CCMT 09T3 indexable inserts, the holder minimises inventory pressure by standardising on a widely available insert format; this compatibility supports lean stocking and straightforward replacement cycles. The cartridge is intended for integration into a boring tool set, enabling modular upgrades without complete holder replacement. Built under Teknik Makina manufacturing guidelines, the component balances practical workshop demands with engineering robustness, helping maintain consistent surface finish and dimensional control in internal turning tasks For application advice or to secure the Cartridge 80-130mm from Teknik Makina (SKU THB09TM), contact Metav Werkzeuge in Emmerich at info@metav-werkzeuge.com or +49 2822 7131930 for tailored support and rapid supply Technical data Article number / SKU: THB09TM Manufacturer: Teknik Makina Designation (EN): Cartridge 80-130mm for Boring Tool eClass: 21041590 Specifications Clamping range: 80–130 mm Torx key: T15 Torx screw: M3.5x8.5 Compatible inserts: CCMT 09T3 Special features For boring tool set Insert compatibility with CCMT 09T3 Robust Torx T15 fastening Files: 62de7e64a9cff922f4703d2f, 62de7ef033927e49dbf32799 FAQ Which insert type fits the cartridge? The cartridge is compatible with CCMT 09T3 indexable inserts and is designed to accept that insert format for stable internal turning. What clamping range does the holder support? The clamping range is 80–130 mm, allowing one mounting unit to service a range of bore diameters in a boring tool set. What fastening hardware is specified? Fastening uses a Torx T15 drive and a M3.5x8.5 screw to ensure secure assembly and reliable resistance to cutting forces. Is this component suitable for modular boring systems? Yes, the cartridge is intended for integration into modular boring tool sets and reduces the need for multiple dedicated holders. How is the product identified for ordering? Order reference is THB09TM, listed under Teknik Makina as the Cartridge 80-130mm for Boring Tool. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combining a 75° cutting geometry with a robust Ø 80 mm body and six indexable edges provides stable, repeatable facing and reduced downtime; the 27 mm shank adds secure mounting for heavy cuts. Order the face milling head directly via Metav Werkzeuge or ask our consultants if needed Face milling head T152TM — for SPKN 1203 indexable inserts, 75° cutting angle (Teknik Makina) A face milling head engineered for reliable facing and finishing with SPKN 1203 indexable inserts, suitable for production and workshop environments. Face milling head for SPKN 1203 inserts 75° cutting angle for flat surfaces Ø 80 mm with six cutting edges 27 mm shank, robust 1.26 kg construction Stable, accurate facing for repeatable results The tool’s 75° cutting angle and compact diameter deliver a stable cutting geometry that supports consistent surface quality across repeated jobs. With six cutting edges, the system lengthens productive cutting time between indexings and lowers the frequency of tool changes, which directly improves machining throughput. The combination of the compact Ø 80 mm body and the defined cutting geometry reduces vibration and helps achieve a uniform finish on facing operations, making the assembly particularly suited to tasks where a flat, even surface is required. Efficient insert system that reduces downtime and handling Designed for SPKN 1203 indexable inserts, the head accepts widely used insert types, simplifying procurement and stock management. Mounting and service are straightforward thanks to the delivered fasteners (M8x24-L) and standard 5 Allen tool engagement, enabling rapid insert changes and secure clamping. The 27 mm shank ensures positive locating in the toolholder, translating into reliable runout characteristics and repeatable positioning for each index. These features together reduce non-productive time and support predictable cycle planning in a busy production schedule. Workshop-ready construction and clear handling benefits At 1.26 kg overall weight and a compact overall length 55 mm, this cutter head balances rigidity and manoeuvrability for manual set-up and CNC applications alike. The design concentrates mass close to the spindle, aiding stable cutting under moderate loads while the modular insert principle keeps long‑term running costs down: worn inserts are replaced rather than the entire head. For those new to indexable tooling, indexable inserts are replaceable cutting tips that permit quick renewal of the cutting edge without regrinding, which simplifies maintenance and reduces tooling waste in the long run. For reliable facing performance choose the Teknik Makina T152TM face milling head — contact Metav Werkzeuge in Emmerich for tailored technical advice or to arrange supply via info@metav-werkzeuge.com or +49 2822 7131930 Technical data Article number: T152TM Name: Face milling head (Planmesserkopf) Brand: Teknik Makina eClass: 21180902 Facts Diameter: 80 mm Shank diameter: 27 mm Cutting angle: 75° Number of cutting edges: 6 Overall length: 55 mm Weight: 1.26 kg Fastener: M8x24-L Key size: 5 Allen Special features For SPKN 1203 indexable inserts Compact design for stable facing Modular insert system for quick renewal Suitable for production and workshop use FAQ Which inserts are compatible with this milling head? The face milling head accepts SPKN 1203 indexable inserts, offering a standardised insert format for easy replacement and inventory management. How is the milling head secured in the toolholder? The T152TM uses a 27 mm shank for positive locating; fastening is performed with the supplied M8x24-L screw and a 5 Allen key for secure clamping. Is the head suitable for finishing passes? Yes — the 75° cutting angle and six cutting edges make the head appropriate for facing and finishing applications where a smooth, flat surface is required. What dimensions should be considered when setting up the tool? Key dimensions are Ø 80 mm diameter, 55 mm overall length and 27 mm shank diameter; account for these when selecting a compatible toolholder. Does the design support quick insert changes in production? The modular nature and standard fastening allow fast insert changes, which reduces downtime and supports continuous production workflows. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of robust 80 mm diameter, six cutting edges and a precise 43° cutting angle for efficient face milling with OFCR 0704 indexable inserts; order directly via Metav Werkzeuge or request technical advice from our consultants. Planing Cutter Head T264TM – 80 mm, 6‑edge cutter for OFCR 0704 inserts (Teknik Makina) A Planing Cutter Head T264TM designed for high‑efficiency face milling applications with OFCR 0704 indexable inserts, suitable for use in production and workshop milling systems. 80 mm head diameter Six cutting edges for continuous cutting Compatible with OFCR 0704 indexable inserts Ø27 mm shank with BK300 clamping Precision and higher throughput in face milling The T264TM head translates a compact design into measurable productivity gains: the 80 mm diameter combined with a 43° cutting angle produces a favourable chip flow and lower cutting forces, which helps achieve consistent surface finish and extended insert life. By using OFCR 0704 indexable inserts, the tool enables rapid insert changes and predictable cutting performance, reducing unplanned downtime and simplifying tool management in small to medium batch production. Secure clamping and straightforward maintenance A robust clamping concept is provided by the BK300 clamp and a M8x18 locking screw, supported by a 4 mm Allen key for routine service. This arrangement ensures reliable seating of each insert and repeatable indexing; the solid Ø27 mm shank secures the head in common toolholders. The result is minimal vibration and stable cutting conditions, which lowers scrap rates and keeps set‑up times short — a direct benefit for busy workshops and CNC cells where throughput and repeatability matter. Versatile suitability and application reasoning Designed for processors of general steels and typical workshop materials, the cutter head accepts OFCR 0704 inserts that are adjustable for a range of feed and depth settings. The head's six cutting edges allow for balanced material removal and can be rotated or replaced to match job demands. Explaining the term: indexable inserts are separate carbide cutting pieces that are clamped into the head, offering cost‑efficient renewal of the cutting geometry without changing the complete tool body. Operational advantages that affect the bottom line Using this cutter head supports a rational approach to tooling: fewer full tool replacements, quicker maintenance cycles and consistent machining quality. The compact overall length of 50 mm keeps the tool‑overhang short for improved rigidity, while a dedicated design for OFCR 0704 inserts helps standardise inventory across similar milling operations. These factors combine to enhance machining economy and support predictable production planning. For Teknik Makina quality and practical tool advice, contact Metav Werkzeuge for availability and technical consultation — Metav Werkzeuge is ready to advise from Emmerich: +49 2822 7131930 or info@metav-werkzeuge.com Technical Data Article number: T264TM Manufacturer: Teknik Cutting Tools Brand: Teknik Makina Facts Diameter: 80 mm Cutting edges: 6 Overall length: 50 mm Shank diameter: Ø27 mm Cutting angle: 43° Weight: 1.205 kg Special features Suitable for OFCR 0704 indexable inserts Clamping: BK300 Locking screw: M8x18 Service tool: 4 mm Allen key FAQ What inserts fit this cutter head? The cutter head is designed for OFCR 0704 indexable inserts; Teknik Makina specifies this interface to ensure correct seating and cutting geometry. How is the head secured in the toolholder? Securing is via a Ø27 mm shank with BK300 clamping; the M8x18 locking screw provides axial retention. Can inserts be changed quickly on the shop floor? Yes, the tool uses indexable inserts so replacement is fast and does not require changing the whole cutter head. Is the cutter head suitable for heavy roughing? The six cutting edges and 43° cutting angle support robust material removal, while the compact design reduces overhang and improves rigidity for demanding cuts. What maintenance tools are required? A 4 mm Allen key is used for the locking screw; routine checks of clamp and insert seating are recommended. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the combination of 45° cutting geometry, secure Torx fastening and compatibility with SNEU 1206 inserts for consistent surface quality and reliable cycle times — order directly via Metav Werkzeuge or request application advice from our consultants. Face milling head T166TM — 45° cutting angle, Ø 80 mm, for SNEU 1206 indexable inserts (Teknik Makina) Face milling head T166TM — a robust milling solution suited to face cutting and light shoulder milling operations with SNEU 1206 indexable inserts and standard 27 mm mounting Compatible with SNEU 1206 indexable inserts 45° cutting angle for controlled chip evacuation Ø 80 mm cutter head diameter M5x12 Torx screw with T20 key for secure fixing Consistent surface finish through optimised cutting geometry The head's 45° cutting angle is designed to balance cutting force and surface quality: the approach reduces radial load while improving chip formation, which results in a more even finish on machined faces. With compatibility for SNEU 1206 indexable inserts the assembly supports economical insert usage and straightforward regrinding strategies. These characteristics help maintain stable cycle times on serial and job-shop production runs while limiting vibration and tool deflection. The combination of geometry and insert compatibility therefore produces a measurable improvement in process reliability. Secure mounting and simple service routines A short, rigid mounting with a 27 mm shank and fastening via an M5x12 Torx screw (T20 key) provides a compact clamping system that reduces run-out and simplifies changeover. The compact overall length contributes to stability during face milling operations, and the straightforward screw-and-insert arrangement reduces downtime during maintenance or indexable insert changes. The relatively low mass of 1.252 kg supports faster spindle acceleration and deceleration where applicable, improving throughput without compromising stiffness. High material removal potential with multiple cutting edges With an outside diameter of Ø 80 mm and 7 cutting edges, the cutter head spreads cutting forces across several inserts, lowering the unit load per cutting edge. This distribution supports longer insert life and enables consistent material removal rates on steels and general workshop materials. The head's layout is particularly suited to finishing passes and light-medium roughing where surface integrity and dimensional stability are priorities. Applications, users and workshop benefits The component is targeted at machine shops and industrial workshops requiring a compact, reliable milling solution for face machining and light shoulder work on conventional and CNC mills. The tool's construction emphasises process stability and reproducible results, making it appropriate for production environments that demand repeatability rather than experimental tool trials. If process validation is required, the Metav Werkzeuge team can advise on suitable insert grades and cutting parameters to match batch sizes and material types. For precision milling with a reliable 45° face milling head, contact Metav Werkzeuge for technical guidance and fast supply — eMail info@metav-werkzeuge.com or call +49 2822 7131930 for application recommendations and availability. Technical Data Article number: T166TM Manufacturer: Teknik Makina Product: Face milling head for SNEU 1206 indexable inserts Diameter: 80 mm Total length: 50 mm Number of cutting edges: 7 Shank diameter / mounting: 27 mm Weight: 1.252 kg Cutting angle: 45° Torx screw: M5x12 Torx key size: T20 Compatible inserts: for SNEU 1206 indexable inserts Intended use: face milling / light shoulder milling Mounting system: Torx screw fixation Construction: compact, short overall length Application focus: stability and repeatable surface quality FAQ What insert type is recommended for this milling head? The face milling head T166TM is specified for use with SNEU 1206 indexable inserts to ensure correct seating and cutter geometry. Which fastening hardware secures the inserts and head? Fixing is accomplished with an M5x12 Torx screw, tightened with a T20 Torx key for reliable clamping. What diameter and number of cutting edges does the head provide? The cutter has an Ø 80 mm diameter and 7 cutting edges, a combination chosen to improve load distribution and surface finish. Is the head suitable for heavy roughing operations? The design prioritises stability and finishing capability; it is best used for face milling and light to medium material removal rather than heavy roughing. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of the 80 mm diameter, six cutting edges and secure M5x12 Torx clamping to increase material removal rates and reduce tool change frequency; order the planing cutter head directly via Metav Werkzeuge or consult our specialists for integration advice. Planing cutter head T211TM – 80 mm diameter, for ODHT 0605 indexable inserts (Teknik Makina) The Planing cutter head T211TM is a compact tool head designed for face planing and finishing with ODHT 0605 indexable inserts, suitable for production and job-shop milling applications 80 mm diameter for broad cutting paths Six cutting edges for continuous material removal For ODHT 0605 indexable inserts (Walter compatible) Clamped with M5x12 Torx screw (T20) Faster throughput through optimised cutter geometry The T211TM tool head combines an 80 mm diameter with a 43° cutting angle, which yields smooth chip formation and steady cutting forces. This geometry is aimed at improving cycle times on face-planing operations while maintaining surface quality. The combination of diameter and cutting angle reduces chatter risk in typical milling set-ups, allowing shops to pursue higher feed rates without compromising stability. The design is particularly effective when used with high-performance indexable inserts intended for finishing and roughing sequences. Quick insert changes and reliable clamping for uptime Tool changes are simplified by the standardised clamping arrangement: a M5x12 Torx clamping screw with a T20 key interface secures each insert. The use of ODHT 0605 inserts means insert indexing is straightforward and repeatable, reducing downtime during maintenance. Compatibility with Walter-type inserts ensures access to a wide range of grades and geometries for various materials, so the cutter head supports flexible process planning and quick adaptation to different workpieces. Robust shank and compact overall size for versatile mounting A 27 mm tool shank and an overall length of 50 mm make this cutter head easy to integrate into common toolholders while keeping the overhang short, which helps to preserve rigidity. The head's mass (approx. 1.07 kg) contributes to stable cutting behaviour on both manual milling machines and CNC equipment, particularly in interrupted cutting where momentum aids consistency. These dimensions are suited to shops that require a compact, yet capable, tool head for face milling and planing tasks. Practical benefits for workshops and production lines Specifying a purpose-built cutter head like the T211TM supports predictable shop-floor results: fewer tool changes, consistent tool seating and wide insert availability for different materials. The head is intended for industrial users who prioritise uptime and repeatable geometry; it fits into multi-step machining processes where a reliable face-planing solution is needed. For procurement, the compatibility with common ODHT 0605 inserts simplifies stock management and provides access to established insert technology. Contact Metav Werkzeuge for detailed integration advice on the Teknik Makina T211TM planing cutter head and to discuss compatible insert grades—call +49 2822 7131930 or email info@metav-werkzeuge.com Technical data Article number: T211TM Manufacturer: Teknik Makina Designation: Planing cutter head for ODHT 0605 indexable inserts Core data Diameter: 80 mm Overall length: 50 mm Shank diameter / Aufnahme: 27 mm Cutting angle: 43° Cutting edges: 6 Weight: 1.07 kg Clamping screw: M5x12 Torx key size: T20 Features Compatible with ODHT 0605 indexable inserts Suitable for Walter insert systems Compact tool head for face planing applications FAQ Which inserts fit this cutter head? The T211TM accepts ODHT 0605 indexable inserts; the cutter head is designed for that insert size and is compatible with standard Walter-formatted grades. How is the insert secured in the tool head? Inserts are clamped using an M5x12 Torx screw; the recommended key interface is T20 for secure and repeatable fastening of the insert. What are the key dimensions to check for mounting? Important dimensions include the 80 mm cutter diameter, 27 mm shank diameter and 50 mm overall length—these determine holder compatibility and overhang. Is the cutter head suitable for production use? Yes, the Teknik Makina T211TM is designed for industrial face-planing and finishing operations where predictable tool behaviour and quick insert changes are required. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact, high-performance face-milling solution with a robust Ø80 mm head, 8 cutting edges and a standard 27 mm clamping shank for consistent chip removal and long tool life; purchase and technical advice are available through Metav Werkzeuge. Planmesserkopf — face-milling head for PNMU 1206 indexable inserts by Teknik Makina, Ø80 mm, 8 cutting edges A Planmesserkopf designed for heavy-duty face milling and fine finishing in mixed production environments, compatible with PNMU 1206 indexable inserts and standard workshop toolholders Ø80 mm head diameter for high metal removal rates 8 cutting edges for uniform surface quality 27 mm clamping shank for secure attachment Compatible with PNMU 1006 / PNMU 1206 indexable inserts Increase throughput with a balanced Ø80 mm design The Ø80 mm head diameter combined with eight cutting edges delivers a stable cutting action that improves cycle times while maintaining surface finish. The multi-edge layout reduces individual cutting load and spreads wear, which extends insert life and keeps changeover frequency to a minimum. For machining operations that demand both stock removal and controlled finish, this cutter head provides a reliable compromise between aggressive removal rates and surface integrity. The solid mechanical design ensures consistent results even under varying feed rates. Fast insert replacement and standardised clamping for uninterrupted work Integration with common indexable formats such as PNMU 1206 (and compatible PNMU 1006) simplifies logistics and tooling planning. The head uses M4x10 fixing screws and a Torx T15 interface to secure inserts, enabling quick, repeatable changes with standard workshop tools. The 27 mm shank offers a secure mounting in conventional toolholders, reducing runout and vibration. These features minimise downtime and make the component easy to service during planned maintenance windows, supporting continuous production workflows. Engineered for repeatability and predictable performance A total height of 50 mm and the head’s geometry contribute to a rigid setup that helps maintain concentricity and repeatable cutting conditions. The arrangement of eight teeth produces a steady chip flow and lowers the load per tooth, which reduces the risk of thermal peaks and edge chipping. Where process stability and reproducible tolerances are essential, the head’s construction supports predictable tool behaviour across batches. Documentation and compatibility with common insert manufacturers further simplify procurement and quality planning. For tailored advice or to secure supply through Metav Werkzeuge — contact our specialists at info@metav-werkzeuge.com or call +49 2822 7131930; Metav’s technical team will advise on integration and cutting data for specific materials Technical Data Article number: T724TM Name: Planmesserkopf Description: for PNMU 1206 Indexable Inserts Manufacturer: Teknik Makina Facts Head diameter: 80 mm Total height: 50 mm Cutting edges: 8 Shank / clamping diameter: 27 mm Fixing screw: M4x10 Torx key size: T15 Special features Compatible inserts: PNMU 1006 / PNMU 1206 Insert grade / designation: TGTC Compatible insert manufacturer: YG-1 Suitable for face-milling applications Robust, workshop-friendly clamping system FAQ Which insert type fits the head? The head accepts PNMU 1206 format inserts; PNMU 1006 inserts are also listed as compatible and the cutter is aligned to common PNMU geometries. What fixing hardware is required for insert replacement? M4x10 screws secure the inserts; a Torx T15 key is used for straightforward, repeatable tightening during servicing. What are the key dimensions to check for toolholder compatibility? Verify a head diameter of 80 mm and a 27 mm clamping shank; these dimensions are critical for correct seating and concentricity in the toolholder. Is the cutter suitable for finishing as well as roughing? With eight cutting edges and a stable head geometry, the cutter head balances material removal and surface quality, making it suitable for both roughing and light finishing passes when paired with appropriate inserts. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Take advantage of a compact corner tool holder that combines a 90° cutting geometry with secure clamping and broad compatibility for efficient turning operations; order the component directly through Metav Werkzeuge or consult our specialists for application-specific setup and delivery from Emmerich. Corner tool holder T493TM — for LNGX 1307 indexable inserts, 90° cutting angle (Teknik Makina) A robust corner turning head designed for external turning and facing tasks, the corner tool holder T493TM suits workshops requiring repeatable, precise 90° corner cuts with LNGX 1307 indexable inserts 90° cutting geometry for precise corner turning Compatible with LNGX 1307 indexable inserts 27 mm shank diameter for secure clamping M4x10 Torx screw; T15 Torx key required Consistent, accurate corner turning from the 90° geometry The central advantage of this tool is its 90° cutting angle, which delivers predictable corner profiles and simplifies toolpath planning on lathes or turning centres. Fitted for LNGX 1307 indexable inserts, the holder supports efficient chip removal and repeatable seating, with seven cutting edges providing multiple index positions before replacement is required. This arrangement reduces non-productive time and improves process reliability, while the defined geometry aids programmers and operators in achieving consistent part geometry across production runs. Fast, secure mounting that keeps set-up time low A 27 mm shank provides a stiff interface to the turret or toolpost, reducing chatter and keeping tolerances tight during interrupted cuts. The insert is clamped using an M4x10 Torx screw, released and tightened with a T15 key, allowing quick insert changes and straightforward torque application with standard maintenance tools. These features combine to shorten machine downtime and deliver a dependable clamping solution that supports predictable tool life and surface finish. Broad system compatibility for flexible tooling strategies Compatibility with LNGX 1307 indexable inserts and proven fitment for Walter insert systems makes the holder a practical choice when consolidating tooling inventories or switching between supplier inserts. The acceptance of established insert formats means straightforward integration into existing tooling families, enabling shops to standardise on a small number of holders while retaining a wide range of cutting grades and geometries from different insert manufacturers. Durable dimensions engineered for workshop conditions With an 80 mm diameter head and 50 mm overall length, the toolholder balances reach and rigidity for many external turning tasks; the unit weight of 1.124 kg provides mass that dampens vibration without excessive bulk. The construction and geometry aim to withstand the rigours of daily workshop use, supporting stable cutting conditions and contributing to consistent surface quality and dimensional control on finished parts. Contact Metav Werkzeuge for tailored advice on Teknik Makina tooling and fast supply of the T493TM corner tool holder — call +49 2822 7131930 or email info@metav-werkzeuge.com for application guidance and delivery from Emmerich Technical data Article number: T493TM Manufacturer: Teknik Makina Designation: Corner tool holder for LNGX 1307 indexable inserts ECLASS: 21181015 Facts Shank diameter: 27 mm Head diameter: 80 mm Overall length: 50 mm Cutting edges: 7 Cutting angle: 90° Weight: 1.124 kg Special features Torx screw: M4x10 Torx key: T15 For indexable inserts: LNGX 1307 Compatible with insert manufacturer: Walter FAQ What insert type does this holder accept? The holder is designed for LNGX 1307 indexable inserts and is compatible with systems from Walter, enabling use of standard insert grades. Which fastener is used to secure the insert? An M4x10 Torx screw secures the insert; a T15 Torx key is recommended for correct tightening and release. What shank diameter is required for mounting? The tool has a 27 mm shank diameter, which fits turrets and toolposts designed for that shaft size and offers increased rigidity. Is the T493TM suitable for heavy-duty cuts? The combination of a substantial head (Ø 80 mm) and 27 mm shank provides good stiffness for many external turning operations; select cutting data and insert grade according to workpiece material and depth of cut. How does the holder improve uptime? By accepting widely used LNGX 1307 inserts and using a simple M4x10/T15 clamping method, the holder reduces insert-change time and supports predictable tool life, helping to maintain steady production. Manufacturer: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; +49 2822 7131930; eMail: info@metav-werkzeuge.com

Combine robust Ø80 mm cutting performance with 7 cutting edges and a secure 27 mm shank for reliable machining results; order the round insert cutter T294-1TM via Metav Werkzeuge or contact our consultants for integration advice. Round Insert Cutter T294-1TM — Ø80 mm, for RDMT 1003 indexable inserts by Teknik Cutting Tools Round Insert Cutter T294-1TM for precision indexable-insert milling in production and workshop environments Ø80 mm cutting diameter 7 cutting edges for smooth stock removal 27 mm shank diameter for secure clamping Compatible with RDMT 1003 indexable inserts High cutting capacity for steady material removal The T294-1TM is designed for consistent chip evacuation and stable cutting in repetitive machining tasks. With a Ø80 mm cutting diameter and 7 cutting edges, the tool distributes cutting forces across multiple inserts to reduce vibration and improve surface finish. Using round indexable inserts simplifies edge changes and lowers tooling costs compared with solid cutters; worn geometry is restored by replacing individual inserts rather than the complete head. This configuration is particularly suited to CNC milling operations where cycle-time stability and predictable tool life translate directly into measurable productivity gains. Secure clamping and fast serviceability to reduce downtime A 27 mm clamping diameter provides a rigid interface with compatible toolholders for repeatable concentricity. The cutter uses a locking screw M3.5 and a Torx retention screw M3.5x8.5, serviceable with a T15 Torx key, enabling quick insert changes with minimal setup time. The modest mass (approx. 1.048 kg) contributes to a compact, well-balanced assembly that is easy to handle during tool changes. Together, these features support efficient maintenance cycles and limit machine downtime — an operational advantage for medium- and high-volume production environments. Compatibility and practical workshop applications Specifically configured for RDMT 1003 indexable inserts, this cutter is a pragmatic choice where insert interchangeability and flexibility matter. The tool’s geometry and insert interface are aimed at general-purpose milling tasks such as light roughing and finishing where round inserts offer predictable wear patterns. Because inserts can be rotated or replaced individually, the cutter supports cost-effective tool management and reduces overall tooling spend. The simple mechanical setup and widely available Torx hardware also make the cutter straightforward to integrate into existing tool libraries. For reliable deployment and to discuss application-specific recommendations for Teknik Cutting Tools' round insert cutter, contact Metav Werkzeuge for personalised advice and ordering at info@metav-werkzeuge.com or call +49 2822 7131930 Technical data Article number: T294-1TM Manufacturer: Teknik Makina Designation: for RDMT 1003 Indexable Inserts Core technical data Diameter: 80 mm Shank diameter: 27 mm Total length: 50 mm Cutting edges: 7 Weight: 1.048 kg Special features Suitable for RDMT 1003 indexable inserts Locking screw: M3.5 Torx screw: M3.5x8.5 Torx key: T15 FAQ Which inserts fit this cutter? The cutter accepts RDMT 1003 indexable inserts as specified for the T294-1TM round insert cutter. What is the shank diameter for toolholder selection? The tool features a 27 mm shank diameter, suitable for holders matching that diameter. How many cutting edges are on the cutter head? The cutter is supplied with 7 cutting edges, optimised for balanced cutting performance. Which fastening hardware is required for insert changes? Insert retention uses an M3.5x8.5 Torx screw and a T15 Torx key; the locking screw is M3.5. What are the overall dimensions to check for tool clearance? The main dimensions are Ø80 mm diameter and 50 mm total length for the T294-1TM. Manufacturer / Responsible: Teknik Cutting Tools, Buyukkayacık OSB Mah.422 Nolu Sokak.No:9, Selcuklu/KONYA/TURKEY / Responsible: Metav Werkzeuge GmbH; Parkring 45; 46446 Emmerich; Germany; +49 2822 7131930; eMail: info@metav-werkzeuge.com